MAINTENANCE MANUAL

JP-402
2857 PUMPS
JP-100
JP-75 0293
0414

JP-300
0640
JP-150
0431

MQUINAS AGRCOLAS JACTO S.A.

Rua Dr. Luiz Miranda, 1650
17580-000 - Pompia - SP - Brazil
Tel.: +55 14 452-1811 - Fax: +55 14 452-1306
E-mail: jacto@jacto.com.br

08/99 - 750935 - MI-0097

 STATEMENT OF LIMITED WARRANTY

WARRANTY EXCLUSIONS:
- Parts considered as normal maintenance such as: filtering elements, belts, hoses,
nozzles, pistons, pressure gauges, as well as usual maintenance, adjustments,
retightening, lubrication and painting.
- Parts which show wear or tear due to use, UNLESS THEY SHOW DEFECTS IN
WORKMANSHIP, ASSEMBLY OR MATERIAL.
- Hydraulic, lubricating oils and grease.
- Injuries of personal or material nature to the user, owner, or third parties.
- Additional charges resulting from paralyzation and repair of the equipment.
- Freight charges, pick up and delivery charges.
- Damages of any nature resulting from action of gases or liquids used in the equipment.

GENERAL INFORMATION:
- Defective parts replaced under warranty period shall be property of JACTO.
- Eventual delays in performing services do not confer to the owner the right to
indemnity or to extension of the warranty period.
- JACTO reserves the right to change its products or to interrupt manufacturing the
equipment.
- THIS LIMITED WARRANTY shall be understood by its expressed terms, and no one in
anyway subject to JACTO shall be authorized to modify or amplify the conditions prescribed
herein.
- In case of need for warranty request, call for the authorized dealer supplying all
information required for a prompt compliance. Do not forget the identification of the
equipment, total hours of work, and the noticed defect.

FOR THIS WARRANTY TO BECOME EFFECTIVE THE PRODUCT REGISTRATION

CARD FOUND IN THE INSTRUCTION MANUAL MUST BE FILLED IN AND RETURNED
TO YOUR JACTO DEALER. THIS CARD MUST BE SIGNED BY THE ORIGINAL RETAIL
BUYER, INDICATING THAT HE HAS READ AND UNDERSTOOD ALL SAFETY AND
OPERATIONAL INTRUCTIONS IN THE MANUAL. FURTHER THE RETAILING DEALER
HAS EXPLAINED TO THE ORIGINAL RETAIL BUYER ALL SAFETY INSTRUCTIONS. IN
NO CASE WILL WARRANTY BE SUPPLIED UNTIL THIS CARD, PROPERLY COMPLETED
AND SIGNED, IS ON FILE WITH JACTO RETAILING DEALER. A COPY OF THE PRODUCT
REGISTRATION CARD SHOULD BE KEPT BY THE ORIGINAL OWNER, AS WELL AS
THE COMMERCIAL INVOICE.

39
 STATEMENT OF LIMITED WARRANTY TABLE OF CONTENTS

Presentation
MQUINAS AGRCOLAS JACTO S.A. warrants the equipment described Introduction ............................................................................................................. 04
herein and agrees to repair or replace parts and components which, under normal Identification plate .................................................................................................. 04
Specifications ......................................................................................................... 05
operation and wear, following the technical recommendations, show DEFECTS Maintenance tools ........................................................................................... .05
IN MATERIAL OR WORKMANSHIP. Maintenance of JP-402 pump
Disassembling the pump
- WARRANTY PERIOD I - Disassembling the hydraulic part ................................................................... 07
II - Disassembling the mechanical part................................................................. 08
- One (1) year from the purchase date by the original retail purchaser. Assembling the pump
III - Crankshaft ...................................................................................................... 10
- WARRANTY APPLICATION: IV - Crankshaft and pump body ............................................................................. 12
V - Piston ............................................................................................................. 13
VI - Valves ............................................................................................................. 14
Jacto or its authorized representative shall honor this warranty, if any part or VII - Valve Analysis ................................................................................................ 15
component shows confirmed defect in workmanship. VIII - Head ........................................................................................................16
IX - Lubrication ...................................................................................................... 16
- IT SHALL BE UNDERSTOOD THAT THE REPLACEMENT OF ASSEMBLIES X - Final tests ....................................................................................................... 17
Maintenance of JP-75 / 100 / 150 / 300 pumps
SHALL BE ONLY PERFORMED IN CASE THAT THE DEFECT CANNOT BE Trouble-shooting
REPAIRED BY REPLACING PARTS AND/OR COMPONENTS. 1 - Excessive liquid leakage through the drain hole .............................................. 19
2 - Liquid leakage between the cylinder and head ................................................. 19
THIS WARRANTY IS NULL AND VOID IF: 3 - Lubricating oil leakage through the drain hole .................................................. 20
4 - Defficient suction and pumping ........................................................................ 20
- Equipament is not used in accordance with the INSTRUCTIONS MANUAL, 5 - Inner noises .................................................................................................... 21
6 - Preventive maintenance ................................................................................... 21
overwork or accidents, Disassembling the pump
1 - Disassembling the hydraulic part .................................................................... 22
- Improper preventive maintenance or performed by unauthorized people. 2 - Disassembling the mechanical part ................................................................. 24
Checking the parts condition
- Modification of the equipment in any way from the original design. 1 - Piston cup ...................................................................................................... 26
2 - Tappet/Connecting rod .................................................................................... 26
- Change, damage, or loss of the product indentification plate. 3 - Rod guide housing .......................................................................................... 27
4 - Crankshaft ...................................................................................................... 27
- Utilization of parts and components not supplied by JACTO. 5 - Valves ............................................................................................................. 27
6 - Valve spring test ............................................................................................. 28
PRODUCT REGISTRATION CARD MUST BE COMPLETED BY THE 7 - Valve seal test ................................................................................................ 28
Assembling the pump
ORIGINAL RETAIL PURCHASER, AND RETURNED TO JACTO DEALER 1 - Bearing and crankshaft ................................................................................... 29
WITHIN 30 DAYS OF THE PURCHASED DATE. 2 - Connecting rod and rodded guide .................................................................... 30
3 - Crankshaft ...................................................................................................... 31
4 - Flanges ........................................................................................................... 32
5 - Cylinder guide and ceramic cylinder ................................................................ 33
6 - Valves ............................................................................................................. 34
7 - Head and valves cover ..................................................................................... 34
8 - Plugs ............................................................................................................. 35
9 - Assembling and filling ..................................................................................... 36
10- Lubrication ...................................................................................................... 37
Statement of limited warranty ................................................................................... 38
38 03
 INTRODUCTION ASSEMBLING THE PUMP

10-LUBRICATION
INTRODUCTION
If used under good conditions, that is, with clean and sand-free water, properly RECOMMENDED
PRODUCT PUMP QUANTITY FREQUENCY
diluted agrochemicals and daily cleaning, Jacto pumps are able to work for more PRODUCTS
than 500 hours with no need for repairs. JP-75 1.5 liters
1st change: API-SB or
On the other hand, when using water containing sand and ill-diluted wettable Lubrication JP-100 2.0 liters 30 hours
Superior
powders, the pistons suffer early wear due to use and thus cause liquid leakages oil
JP-150 2.5 liters Further: every SAE-30
through the drain hole . Operating the pump of your sprayer for prolonged time with JP-300 4.0 liters 100 h
leakages will contaminate the grease (JP-402)and the lubricating oil (other pumps)
and incorrect lubrication will cause damage to the connecting rods and bearings,
NOTE: The pump must be placed on a level surface.
thus raising the maintenance cost.
- Fit the level plug and oil plug (breather).
-Test the pump with clean water under around 14 kgf/cm (200 psi) during
IDENTIFICATION PLATE 10 minutes.
In requesting replacement parts or maintenance, always specify the model
and serial number of your pump for prompt and efficient service. These data are
shown on the identification plate affixed to your pump. ATTENTION: Check for eventual leakages, vibrations, strange or excessive
noize. In case of doubt, please do not hesitate to contact your Jacto dealer.

SPRAYER NUMBER

WARNING
MODEL:
The maintenance instructions herein must only be applied to the pump
MAX. PRESSURE kgf/cm
ROTATION: rpm POWER.: HP
after the expiration of the one-year warranty term which shall be in force
FLOW RATE: liters/min as of the purchase date. Within said period the user shall be authorized
MQUINAS AGRCOLAS JACTO S.A - CGC 55.064.562/0001-90 only to perform the replacement of parts subject to usual wear such as
POMPIA - S.P. - MADE IN BRAZIL
piston cups, seals and change of lubricating oil. This except, contact your
Jacto dealer.

Jacto is trademark registered by Mquinas Agrcolas Jacto S.A.

04 37
 ASSEMBLING THE PUMP SPECIFICATIONS

9- Mounting and Filling SPECIFICATIONS

-Install the cork seal and mount the cover PUMP MODEL
FEATURES
- Install the drain plug with the ring. JP-402 JP-75 JP-100 JP-150 JP-300
- Fill the pump with lubricating oil up to the level plug. Max. rotation on crankshaft 540 rpm 540 rpm 540 rpm 540 rpm 540 rpm
Maximum working pressure 300 psi 500 psi 500 psi 500psi 500 psi
Flow rate (liters/min at 540 rpm) 40 75 100 150 300
0419 Power required at 400 psi 2.2 HP 5.3 HP 7.0 HP 10.7 HP 24.0 HP
Cork seal Breather Weight 19.5 kg 37kg 47kg 60kg 125kg

MAINTENANCE TOOLS
Cover
PUMP MODEL
DESCRIPTION
Level plug
JP-402 JP-75 JP-100 JP-150 JP-300
L 1/2" spanner X X
Oil level
L 9/16" spanner X X X
L 3/4" spanner X X X X
7/16" multiended wrench X
1/2" multiended wrench X X X X
3/4" multiended wrench X X
3/4" open-ended spanner X X
15/16" multiended wrench X X
15/16" open-ended spanner X X
Pliers for inner plastic ring X X X X X
Plastic mallet X X X X X
Drain plug Torque wrench X X X X X
Ring
1/2" socke wrench X X X X
9/16" socket wrench X X X
3/4" socket wrench X X X X
15/16" socket wrench X X

36 05
 ASSEMBLING THE PUMP

JP-402 PUMP 8- Plugs

-Mount the plugs with chemical bond or teflon tube sealer.

MAINTENANCE NOTE: The position of plugs and inlet and outlet nipples can vary according to the
equipment. Please note their positions when disassembling the pump.

0415

Outlet Plug

2857
Plug Inlet

06 35
 ASSEMBLING THE PUMP DISASSEMBLING THE PUMP

6- VALVES 417
Guide ring
- Fit the spring and the disc into the cage. Seat I - Disassembling the hydraulic part (heads)
Valve seal
- Position the seat and the guide ring.
- Install the valve seal.
outlet
ATTENTION:
Make sure the parts are clean, free from Disc
impurities and mainly from abrasive
Spring Cage
chemicals

7- Head and valves cover

- Apply two drops of low 0416 Clearance inlet
torque chemical bond to the allowed 2807 2808
Torque
stud bolts and assemble. (4.5 kgf/m
for JP-75 1 - Identify and mark the liquid inlet and 2 - Remove the heads and observe how
-Mount the clip plate, install and JP-100 outlet of the pump. the inlet and outlet valves are mounted,
and 5.5 kgf/ in order to not mount it invert.
the lock washers, apply two m for JP-
drops of medium torque 150 and
300)
chemical bond to the stud Grease
bolt, fit all nuts and next
tighten them with 4.5kgf/m
Ceramic
torque for the JP-150 and sleeve Stud bolt Inlet valve
JP-300 pump. Outlet
Clip plate
Packing valve
ring
NOTE:
Always observe the arrow Head
when mounting the head and Valve
the valves. Valve cover 2809 2810

Torque (4.5 kgf/m for

JP-75 and JP-100, and
5.5 kgf/m for JP-150 and 300)
34 07
 DISASSEMBLING THE PUMP ASSEMBLING THE PUMP

3 - Remove the bolt that is fixing the piston 5-Sleeve guide and ceramic sleeve
and take out the whole assembly. -Install the seal, snap ring and scraper ring in the sleeve guide.
- bolt, NOTE: Make sure the seal is positioned correctly.
- Position the paper seal and mount the sleeve guide to the pump body.
- piston,
-Mount the piston cup and the piston to the ceramic liner.
- piston cup, - Position the paper seal on the liner guide and the piston cup base on the rod.
- sleeve, - Mount the sleeve with the piston cup, position the ring, install the brass washer,
- connecting rod guide, etc. apply two drops of medium torque chemical bond to the rod thread and next fit the
2813
nut.
- Tighten the nut all the way with 4.5 kgf/m torque for the JP-75 & JP-100 pumps
4 - Repeat this operation on the other head. and 5.5 kgf/m torque for the JP-150 & JP-300 pumps.
0420
Torque Nut
Brass waher
Piston

II - DISASSEMBLING THE MECHANICAL PART Piston cup base Ring

Piston
Ceramic sleeve cup
Paper seal
Sleeve guide
Cover Scraper ring

Seal

Protector Snap ring

Pump body Paper
seal
Connecting
rod
2817 2818

1 -Remove the cover and the connecting 2 - Remove the dust guard and the seal
rod. with a spatula.

08 33
 ASSEMBLING THE PUMP DISASSEMBLING THE PUMP

4- Flanges
- Lubricate with oil (API-SB ou superior SAE-30) the flanges housing and install Brass or Crankshaft
Snap ring wood stick
the seal.
- Lubricate the seal with grease. Next mount the paper seal.
- Mount the flanges to the pump body and fit all screws.
- Tighten the screws with 1.6 kgf/m torque.

0422
Seal Bearing flange Small bearing
shaft
2819 2820

3 - Remove the snap ring that is placed 4 - Tap the crankshaft with a brass stick
Make sure the seal is in the pump body. to remove it from the pump body.
correctly positioned.
Attention: Never tap the small bearing
shaft to avoid damaged.

Bearing Flange

Packing

Torque
(1.6 kgf/m)

2821

5 - Remove the cranksaft bearings with an extractor, or use a press properly

supported.
32 09
 ASSEMBLING THE PUMP ASSEMBLING THE PUMP

III - Crankshaft 3-Crankshaft

- Lubricate with oil (API-SB or superior SAE-30) the bearings housing.
- Mount the crankshaft with the bearings to the pump body.
-Lubricate with oil (API-SB or superior SAE-30) the crankshaft journals.
- Mount the other part of the connecting rod and fit the screws (apply low torque
chemical bond) by following the numerical sequence engraved on the connecting
2844 rod.
- Tighten the screws all the way: 1.9 kgf/m torque for the JP-75 & JP-100 pumps
and 2.8 kgf/m torque for the JP-150 pump.
NOTE: Make sure the crankshaft can be turned with the hands after being tightened.

0421
Tube
The position of the crankshaft may vary on each
equipment. Please note the groove position
Bearing* when disassembling the pump.
Rod
Lubrication
channel

Wood basis Crankshaft

Pump body
2823 2824

1 - Check if the lubrication channels are 2 - Mount the bearing (with the grease
obstructed. deflector toward the outside). Tap until Connecting
it rests. rod
*The bearing is armor-plated on one
side, which must be toward the outside Bearing
so that the other receives the lubrication.
The crankshaft assembly way and
numerical sequence of the connecting
NOTE: THE TUBE USED TO MOUNT THE BEARING SHOULD TOUCH ONLY rod: a) 1.1, 2.2, 3.3 (3 -piston model)
b) 1.1, 2.2, 3.3, 4.4 (4-piston model).
THE BEARING INNER TRACK.
Groove

10 31
 ASSEMBLING THE PUMP ASSEMBLING THE PUMP

2- Connecting rod and rodded guide NOTE: The armor -plated side must
face the outside. Small bearing shaft
NOTE: Make sure they are clean. housing
- Fit the connecting rod into the rodded guide.
Spacer ring
- Lubricate with oil (API-SB or superior SAE-30) the connecting rod pin and
mount the assembly. Small
bearing
- Lubricate with oil (API-SB or superior SAE-30) the rodded guide and the guide shaft
housing (on the pump body). Next mount this assemly to the pump body as shown
in the figure below.
Base
Base 2825 2826

0418 3 - Install the spacer ring and the other NOTE: To support the crankshaft use a
bearing with the grease deflector facing piece of wood with a hole,in which to fit
Rod
the outside. the small bearing shaft.

Rod guide

Connecting
rod Oil

Pin

2827 2828

4 - Needle bearing. - Mount the bearing and lock it.

30 11
 ASSEMBLING THE PUMP ASSEMBLING THE PUMP

IV - Mounting the crankshaft assembly to the pump body Some specifc tools are required for assembling the pump. In case you do not
have them, try to use those available, provided that you do not damage the parts.
Follow strictly the sequence shown below.
1- Bearing and crankshaft assembly
NOTE: Make sure they are clean.
- Place the crankshaft on the aluminum plate.
- Install the bearing guide
- Position the bearing with the numbers upward.
2845
- Press the bearing until it is set to the indicated position.
2846
- Disassemble the extension and guide.
1 - Align the crankshaft assembly to the
NOTE: To follow the same sequence for mounting the other bearing..
pump body and tap the external cap (use 2 - Lock the entire assembly by
a tube) until housing completely the instaling the snap ring.
assembly.
0423

3 - Place the seal and the dust guard. Extension

NOTE: Place the seal with the edge upward,
so the seal can eliminate the grease excess
Bearing guide
and prevent dirts from entering.

2847 Crankshaft

4 -Install the matching cover and the external cover. Bearing

-Fit the screws and tighten them sequenced
crosswise with 0.5 kgf/m torque.
Aluminum plate
Matching cover Bearing seat

2848

5 - Lubricate the pump with

grease. Gasket tightener
2848 External cover

12 29
 CHECKING THE PARTS CONDITION ASSEMBLING THE PUMP

6- Valve spring 0426 V - Mounting the pistons assembly

-Fit the spring, packing disc and

seat in the cage.
200 g 100 g
-Place weights of 100 g (for JP-75 &
JP-100 pumps) and 200 g (for JP-150
& JP-300 pumps) on the seat and Seat
check if the seat rests on the cage. If
Spring
not, replace the spring and test again.
Cage

Valve with improper seal caused by wear, impurities or stuck disc results in 2851
2850
deficient suction and pumping.
1 - Install the seal and the seat washer. 2 - Fit the spacer bushing and the o-ring
over the spacer bushing.
7- Valve seal
- Place a thin sandpaper on a straightener and smooth the seating sides of the
disc and valve seat with 8-shaped movements.
- Mount the valve and pour water as
shown in the figure.
- If it leaks, replace the valve.
Water

Seal

0427
2836 2852

ATTENTION 3 - Mount the ceramic sleeve and the 4 -Install the tappet on the connecting
Replace the seals whenever disassembling the valve for repair. rod with the piston cup guide.
o-ring around the sleeve.
28 13
 ASSEMBLING THE PUMP CHECKING THE PARTS CONDITION

3- Rod guide housing

-Check if it is not slack or worn.

0398

Rod guide
2853
housing
2854

5 - Install the piston cup with the 6 - Fit the fixing bolt with the o-ring
piston. and the flat washer.

7 - Tighten it with 3.5 kgf/m torque. 4- Crankshaft

- Check if the crankshaft journal is not scratched.

0407

2855
Crankshaft
8 - Do the same with the other piston assembly. journal

5-Valves 0411
0417
VI- VALVES Guide ring Check: 6 5 4 3 2 1
- Fit the spring and the disc into the cage. Seat 1-Cage
Valve seal 2- Spring
- Position the seat and the guide ring.
3- Packing disc
- Install the valve seal. 4- Seat
5- Seal
ATTENTION: 6- Valve guide
Make sure the parts are clean, free from Disc
impurities and mainly from abrasive Spring Cage ATTENTION: Overcharge on the valve spring will result in deficient suction
and pumping.
chemicals

14 27
 CHECKING THE PARTS CONDITION ASSEMBLING THE PUMP

1-Piston cup VII- VALVE ANALYSIS

Condition Causes 1- Valve spring 3158

Thinner wall Normal wear due to time of use. -Fit the spring, packing disc and
a) Improper maintenance - the inside of the pump seat in the cage. 100 g
is not rinsed after the application of wettable
powdered agrochemicals which are built up on -Place weights of 100 g (for JP-75 & Seat
the cylinder and head walls.
Wear and scratch JP-100 pumps) and 200 g (for JP-150
b) Use of water containing sand - improper
filtering during the filling operation. & JP-300 pumps) on the seat and
Spring
c) Chemical mixture leakage when using wettable check if the seat rests on the cage. If
powdered agrochemicals.
not, replace the spring and test again. Cage
Normal Worn Worn or scratched piston
cups cause liquid leakage
through the drain hole.

0434 0435
Valve with improper seal caused by wear, impurities or stuck disc results in
deficient suction and pumping.
ATTENTION: Whenever disassembling the sleeve and piston cup assembly for
repair, replace the following parts (see figure 0430): sleeve seal (3), packing ring 2- Valve seal
(06) and packing ring(10). - Place a thin sandpaper on a straightener and smooth the seating sides of the
disc and valve seat with 8-shaped movements.
2- Tappet - Connecting rod
- Check if the guides and rods are not worn or scratched. - Mount the valve and pour water
- Check if the connecting rod pin is not worn. as shown in the figure.
Water
- Check if the connecting rod eye is not worn. - If it leaks, replace the valve.
- Check if the connecting rod bearing is not worn or scratched.

0400
Pin
Seal

0427

Rod Guide Connecting Connecting ATTENTION

rod rod bearing Replace the seals whenever disassembling the valve for repair.
26 15
 ASSEMBLING THE PUMP DISASSEMBLING THE MECHANICAL PART

VIII - Assembling the head 2.4- Pull out all the tappets to the front so as to free the crankshaft.
- Mount the heads according to the identification (inlet and outlet) made on the NOTE: Remove the crankshaft carefully in order to avoid impact on the
begining of the disassembling. connecting rod journal.

0404
TORQUES: Crankshaft

1st fase
1.4 to 2 kgf/m (10 to 15 lb/foot).
2nd fase
2.8 to 3.5 kgf/m (20 to 35 lb/foot).
3rd fase:
2843
3.5 kgf/m (25 lb/foot).
- Mount the bearing and lock it.
2.5 - Remove the tappets with the connecting rod and the connecting rod pin.

0405 Connecting
IX - Lubrication Tappet rod
-Lubricate the pump daily, using Lithiun base NGLI-2 grease.

2857

Connecting rod
pin

Grease nipple

16 25
 DISASSEMBLING THE MECHANICAL PART ASSEMBLING THE PUMP

2- Disassembling the mechanical part

X - FINAL TESTS
After finishing the pump assembly, do the following tests to check if the
2.1- Remove the crankcase cover. 0432
pump was correctly repaired.
Drain
plug
1st test: Operate the pump for 10 minutes with no pressure in the circuit.
2nd test:. LIQUID LEAKAGE THROUGH THE DRAIN HOLE.
Check if the leakage was eliminated by operating the pump with pressure
in the circuit.
Crankcase
cover 3rd test: WEAR OF MOVING PARTS
Check if the clearance on the bearings and the strong metallic noises were
eliminated with the pump running at the working pressure.

2.2- Remove the bolts that fix the 0433 4th test: SUCTION AND PUMPING DEFICIENCY
connecting rods. Connecting rod Determine the pump actual capacity.( REFER TO THE INFORMATION
SHEET )

Crankshaft

2.3-Remove the bolts and 0403

the flanges

Flange

24 17
 JP-75 / 100 / 150 / 300 DISASSEMBLING THE HYDRAULIC PART

PUMPS MAINTENANCE 1.4- Remove the sleeve with the piston cup and the base.
- Repeat this operation with the other cylinders.
0425

JP-75 JP-100
0293
0414
1.5- Remove the sleeve seal and the 0401

packing. Sleeve

Seal
JP-300 Packing
0640
JP-150
0431 1.6- Drain the oil. Remove the sleeve Sleeve guide
guide.

0424

1.7-Remove the snap ring from the

sleeve guide and the seal. Sleeve guide
- Snap ring
- Seal

0406

18 23
 DISASSEMBLING THE HYDRAULIC PART TROUBLE-SHOOTING

1- Excessive liquid leakage through the drain hole.

ATTENTION: Observe the parts when disassembling the pump in order to
identify those damaged. There will be leakage if:
- the piston cup is damaged (fig. 0430 - part 8).
1-Disassembling the hydraulic part - the nut fixing the piston cup is not tightened. (fig. 0430 - part 12).
Valves
- Remove the stud bolts fixing the cover
- the packing ring is damaged (fig. 0430 - part 10).
valves cover.
0402
- Remove the valves cover.

Stud bolt

0409

Drain
1.1- Remove the nuts fixing the head, 1.2- Remove the nut fixing the piston
clip plates and head. cup.
0408 Drain
0410

2- Liquid leakage between the sleeve and head.

Clip plate - Retighten the head nuts (fig. 0429).
- If the leakage continues, replace the packing ring (fig. 0430 - part 6).

Head 0429 0428

2

1.3- Remove the nut (12), brass washer (11), packing ring (10) and piston ( 9). 3

0430
1 2 3 4 3 5 6 7 8 9 10 11 12
Packing ring

1
4

22 19
 TROUBLE-SHOOTING TROUBLE-SHOOTING

3- Lubricating oil leakage through the drain hole 5- Inner noises

This can happen due to obstruction in the breather, deficient rod seal
(part 02) and sleeve guide seal (part 3) or improper tightening of the nuts fixing the These noises result from wear on the connecting rod bearing.
head.
01 - Snap ring 07 - Piston cup seat ATTENTION: Check for the exact location of the noises. There may also be noises
02 - Seal 08 - Piston cup
if the filter is obstructed or a valve is not operating properly, thus leading you to a
03 - Packing 09 - Piston
04 - Sleeve guide 10 - Packing ring wrong diagnosis.
05 - Sleeve 11 - Flat washer
06 - Packing ring 12 - Nut
0400
1 2 3 4 3 5 6 7 8 9 10 11 12

0430

4- Deficient suction and pumping Connecting rod

It can be caused by: bearing
-Damaged valve;
- deficient packing on the valves due to impurities or stuck disc;
- incorrect mounting of valves.

To confirm if this deficiency is really caused by the valves, measure the pump
actual flow rate.

- Disconnect the return hose from the control valve and connect the filler unit hose. 6- Preventive maintenance
- Run the sprayer with 540 rpm at PTO.
- Collect water for one minute. Pumps have parts which usually operate under rigorous conditions and thus are
- Measure the volume collected. Return hose subject to normal wear after a reasonable time of use. On our pumps the piston cup,
NOTE: The volume collected should Filler unit which is in continuous contact with abrasive chemical mixtures, is subject to wear
approximate this shown below for each hose
pump model: and therefore can cause liquid leakage through the drain hole. To avoid that such
JP-402 = 40 litersmin a simple problem damage other parts of the pump, a preventive maintenance at the
JP-75 = 75 liters/min
JP-100 = 100 liters/min end of the spraying season or every 300 hours is advisable , with the examination
JP-150 = 150 liters/min of the pistons set and replament of the damaged parts.
JP-300 = 300 liters/min
0412

20 21