Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 660 views

    FGTech Galletto V54 Instruciones

    Uploaded by

    jk
    This document discusses troubleshooting an issue connecting an FGTech Galletto V54 ECU programming tool to a computer. It describes the problem of the software being unable to find the device driver and lists the following solutions: 1) Download and install virtual COM port drivers from the FTDI website 2) Connect the FGTech device only after installing the drivers when it shows as a blank device 3) Use the CMD Uninstaller to remove any overlaying drivers, then reprogram the FGTech firmware and install the Galletto V54 software as outlined in the user manual.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    FGTech Galletto V54 Instruciones

    Uploaded by

    jk
    660 views2 pages
    This document discusses troubleshooting an issue connecting an FGTech Galletto V54 ECU programming tool to a computer. It describes the problem of the software being unable to find the device driver and lists the following solutions: 1) Download and install virtual COM port drivers from the FTDI website 2) Connect the FGTech device only after installing the drivers when it shows as a blank device 3) Use the CMD Uninstaller to remove any overlaying drivers, then reprogram the FGTech firmware and install the Galletto V54 software as outlined in the user manual.

    Original Description:

    FGTech Galletto V54 Instruciones

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document discusses troubleshooting an issue connecting an FGTech Galletto V54 ECU programming tool to a computer. It describes the problem of the software being unable to find the device driver and lists the following solutions: 1) Download and install virtual COM port drivers from the FTDI website 2) Connect the FGTech device only after installing the drivers when it shows as a blank device 3) Use the CMD Uninstaller to remove any overlaying drivers, then reprogram the FGTech firmware and install the Galletto V54 software as outlined in the user manual.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    660 views2 pages

    FGTech Galletto V54 Instruciones

    Uploaded by

    jk
    This document discusses troubleshooting an issue connecting an FGTech Galletto V54 ECU programming tool to a computer. It describes the problem of the software being unable to find the device driver and lists the following solutions: 1) Download and install virtual COM port drivers from the FTDI website 2) Connect the FGTech device only after installing the drivers when it shows as a blank device 3) Use the CMD Uninstaller to remove any overlaying drivers, then reprogram the FGTech firmware and install the Galletto V54 software as outlined in the user manual.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 2

    FGTech Galletto

    V54
    FgTech Galletto 4 Master V54 ECU programming tool
    software, installation and technical support.

    2/18/2016

    FGTech galletto v54 Can not find driver problem


    Problem:

    When install FGTech galletto 4 V54 master software, the FTReadWrite replied Cant find
    device error message. When trying to uninstall the driver, the window screen warmed it is not
    FGTECH device, but USB-to-Serial device. If install the driver, fgtech v54 software did not run
    andFTReadWrite or MProg didn't find the ftdi chip. Try to install the driver on both win 7 and win
    xp computer over and over, but in vain.

    Solution:

    1) Download and install the Virtual Com Port drivers from FTDI website:

    Virtual COM Port Drivers


    http://www.ftdichip.com/Drivers/VCP.htm

    2) Then connect the FGTech to computer via USB port which had no device programmed and 1
    blank device when the MProg Utility it shows.

    NOTE: If you had backup and reprogram with the ept file. The system will not recognize the
    FGTECH and will not reprogram the firmware bin file. The Virtual Com Port
    Drivers would overlay thefgtech ECU programmer. Then you have to again download the
    related driver in FTDI website.

    CMD Uninstaller 1.4


    http://www.ftdichip.com/Support/Utilities.htm

    3) After install the right drivers, FTReadWrite programmed the backup firmware file, run galletto
    v54 software by referring to the user manual on obd365 webpage.

    You might also like