Mil HDBK 773a
Mil HDBK 773a
Mil HDBK 773a
com
NOT MEASUREMENT
SENSITIVE
MIL-HDBK-773A
30 June 2005
________________
SUPERSEDING
MIL-HDBK-773
1 April 1988
DEPARTMENT OF DEFENSE
HANDBOOK
ELECTROSTATIC DISCHARGE
PROTECTIVE PACKAGING
MIL-HDBK-773A
FOREWORD
1. This handbook is approved for use by all Departments and Agencies of the Department of
Defense (DoD).
2. Military packaging has experienced many changes in the packaging of electrical devices.
Many of the new electronic parts and devices are highly susceptible to damage from static
electricity, even at levels that can be neither seen nor felt. Electrostatic Discharge (ESD) affects
many components such as transistors, resistors, integrated circuits, and many types of
semiconductor devices. Static charge can degrade or destroy electronic devices during shipping,
handling, and installation. Often it takes only a small charge to cause this damage. In fact,
nearly half of todays new semiconductors, with their denser geometries, have a static sensitivity
of 100 volts or less. This means that almost any moving object can generate a dangerous charge
in an unprotected environment. A spark discharge resulting from the accumulation of
electrostatic charges does not necessarily destroy a device or cause a circuit in which it is used to
become nonfunctional. The device can be permanently damaged, yet performs its intended
function. Additional exposures to these spark discharges or using the device in a circuit can
further damage and degrade it until failure occurs. This is known as a latent failure and can
seriously affect a systems reliability.
3. It is essential that everyone involved in the acquisition, handling, transporting, and storing of
Electrostatic Discharge Sensitive (ESDS) items be concerned about ESD. All ESDS items
should be packaged, shipped, and stored in ESD protective materials, including condition code F
returns (economically reparable materiel which requires repair, reconditioning, or overhaul).
4. Reducing damage to ESDS items begins with understanding the problem. This handbook is
intended to provide guidelines on precautionary measures for reducing failures as they relate
specifically to packaging and handling of ESDS items.
ii
Downloaded from http://www.everyspec.com
MIL-HDBK 773A
CONTENTS
PARAGRAPH PAGE
FOREWORD ii
1. SCOPE 1
1.1 Scope 1
1.2 Application 1
2. APPLICABLE DOCUMENTS 1
2.1 General 1
2.2 Government documents 1
2.2.1 Specifications, standards, and handbooks 1
2.3 Non-Government publications 3
3. DEFINITIONS 4
4. GENERAL GUIDANCE 6
4.1 Generation of electrostatic charges 6
4.1.1 Dry and moist materials 6
4.1.2 Static charge 7
4.2 ESD damage 7
4.3 Description of an integrated circuit 7
4.3.1 Damage by spark discharge 7
4.3.2 Microscope view 7
4.4 Identification/acquisition 7
4.4.1 Special protective devices 8
4.5 U.S. Air Force 8
5. DETAILED GUIDANCE 8
5.1 Identifying ESDS items 8
5.2 Packaging of ESDS items 9
5.3 Transporting before final unit pack 11
5.4 Condition code F material 11
5.5 ESD protective packaging materials 11
5.6 The ESD protective worksite 11
5.7 Precautions 12
5.8 Typical ESD-controlled workstation 13
iii
Downloaded from http://www.everyspec.com
MIL-HDBK 773A
CONTENTS
PARAGRAPH PAGE
6. NOTES 14
6.1 Intended use 14
6.2 Subject term (key word) listing 14
6.3 Changes from previous issue 14
TABLES
FIGURE
1. Magnified views of ESD caused failure of high-performance 18
operational amplifier
2. ESDS item preservation 19
3. Electrostatic sensitive device labels 20
4. Use of PPP-B-1672, Fast Pack 21
5. Example of ESD protective workstation 22
6. ESD protective worksite items 23
7. Typical ESD protective field service kit 24
A-1. ESD field service kit components 25
APPENDIXES
CONCLUDING MATERIAL 38
iv
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
1. SCOPE
1.1 Scope. This handbook provides detailed guidance for DoD personnel who use,
handle, package, or store Electrostatic Discharge Sensitive (ESDS) items. It is designed to
promote the use of standardized packaging materials as well as promote an understanding of the
Electrostatic Discharge (ESD) threat through all levels of maintenance and supply. This
handbook is for guidance only and cannot be cited as a requirement.
1.2 Application. This handbook is applicable to all DoD personnel involved in assembly,
handling, packaging, and storing of ESDS items.
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed below are not necessarily all of the documents
referenced herein, but are those needed to understand the information provided by this handbook.
FEDERAL SPECIFICATIONS
1
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
2
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
(Copies of ANSI documents are available online at www.ansi.org or from the American National
Standards Institute, 25 West 43rd Street, New York, NY 10036, telephone (212) 642-4900,
facsimile (212) 398-0023.)
(Copies of EIA documents are available online at www.eia.org or from the Electronic Industries
Alliance, 2500 Wilson Boulevard, Arlington, VA 22201, telephone (703) 907-7500.)
(Copies of ESD documents are available online at www.esda.org or from the Electrostatic
Discharge Association, 7900 Turin Road, Building 3, Rome, NY 13440-2069, telephone
(315) 339-6937, facsimile (315) 339-6793.)
ASTM INTERNATIONAL
3
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
3. DEFINITIONS
3.1 Definitions. General definitions of terms unique to this standard are listed below.
Definitions of other terms commonly used in the packaging community may be found in
ASTM D 996.
3.2 Antistatic. Refers to the property of a material that inhibits triboelectric charge
generation effects.
3.3 Antistatic fast pack. Reusable container with antistatic cushioning and the word
antistatic printed on both ends.
3.4 Antistatic tote tray. Conductive containers ideal for static-free storage, kitting, and in-
process handling and transporting of static-sensitive assemblies or devices.
3.5 Conformal coatings. Liquid materials applied directly to Printed Circuit Boards
(PCBs) and electronic components during final manufacture. Once hardened they will provide
physical, electrical, and environmental protection.
3.6 Conductive. Materials defined as being either surface or volume conductive. Such
materials may be either metal or impregnated with metal, carbon particles, or other conductive
ingredients or whose surface has been treated with such materials through a process of
lacquering, plating, metallizing, or printing.
4
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
3.11 Electrostatic Discharge Sensitive (ESDS) items. Electronic items which are
susceptible to damage or degradation as a result of an electrostatic discharge event.
3.12 Electrostatic discharge sensitive (ESDS) labels. All unit packs, intermediate
and exterior containers of ESDS devices (or other electronic items that are alone or are
part of assemblies) that are susceptible to damage from ESD should be marked with an
approved ESDS device attention label.
3.13 Intermediate pack. A wrap, box, or bundle that contains two or more unit
packs of identical items.
3.18 Static electricity. Electrical charge at rest. The electrical charge is due to the
transfer of electrons within a body or from one body to another.
5
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
3.19 Static safe area. Any area that is capable of limiting or controlling static
charge on people and conductive/nonconductive materials.
3.22 Unit pack. The first tie, wrap, or container applied to a single item or a
quantity thereof or to a group of items of a single stock number, preserved or
unpreserved, which constitutes a complete or identifiable package.
4. GENERAL GUIDANCE
4.1.1 Dry and moist materials. Separating dry materials generates greater
electrostatic charges than moist materials because the moistness is sufficiently conductive
and helps to dissipate the charge. For this reason, ESD effects are more noticeable in the
winter since heating systems reduce moisture on the surfaces of furniture and other
objects. Any circumstance that results in a low relative humidity will permit a greater
accumulation of electrostatic charges.
6
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
4.2 ESD damage. As shown in table II, activities such as walking, working at a
bench, and handling common materials can generate thousands of volts of static
electricity. If a spark discharge occurs from an accumulation of electrostatic voltage,
electronic components, PCB components, and other electronic assemblies can be
destroyed or damaged. Spark discharges cannot be felt if the electrostatic voltage is less
than the threshold level for that particular individual. This threshold level is usually
within the range of 2,500 to 4,000 volts of electrostatic charge.
4.3 Description of an integrated circuit. Since the advent of the integrated circuit,
electronic components have become smaller and their functional capabilities have
become greater. A microprocessor, the core element in a microcomputer, is less than
one-half of a cubic inch in volume. Because of the micro-miniature size of the functional
components in an integrated circuit, they are much more susceptible to ESD damage than
their earlier, significantly larger counterparts. Table III provides the relative ranges for
possible damage.
4.3.1 Damage by spark discharge. Considering the threshold levels at which most
people can feel a spark discharge from electrostatic voltage, it is easy to understand how
electronic parts can unknowingly be damaged during handling. If it is not immediately
destroyed, the damaged part may not cause a functional system failure until after it
reaches the user.
7
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
4.4.1 Special protective devices. The requirements for the use of special
protective devices prior to packaging, as with shunting bars, clips, or non-corrosive
conductive foams for protection, is the responsibility of the Government activity involved
in item acquisition. MIL-HDBK-263 and MIL-PRF-87893 provides further guidance in
this area.
4.5 U.S. Air Force. U.S. Air Force activities have been instructed to utilize
ANSI/ESD S20.20 instead of MIL-STD-1686 and ANSI/ESD S541 instead of
MIL-HDBK-263.
5. DETAILED GUIDANCE
5.1 Identifying ESDS items. Due to the tremendous volume of electronic parts
presently used by the military and the methods needed to accomplish the task, identifying
parts that are ESDS is essential. ESDS items are categorized as follows:
a. The FEDLOG Army Master Data File (AMDF) Response for National Stock
Numbers (NSNs) contains a data field identified as ESDC (Electrostatic Discharge
Code). This is a one character alpha code (for example, A, B, C, or D) that indicates
whether an item is susceptible to ESD or electromagnetic interference damage. If there is
not a code in this field, do not assume that item is not ESDS. All owners of ESDS items
have not entered a code in this FEDLOG AMDF data field.
c. All printed circuit cards and wiring boards with mounted ESDS components.
e. The U.S. Army Aviation and Missile Command has identified FSCs 5955,
Oscillators and Piezoelectric Crystals, 5963, Electronic Modules, and 7042, Mini and
Microcomputer Control Devices as ESDS items.
f. The Defense Electronic Supply Center has identified specific resistors and
semiconductors listed below as ESDS items.
8
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
(b) Insulated gate field effect transistors (Metal Oxide Semiconductor Field
Effect Transistors (MOSFET)).
g. A number 3, used to specify a Type Cargo Code (TCC), can be found in the
FEDLOG AMDF Freight Data Response File. In this data file, TCC is a one character
alpha/numeric code used for all shipments via water to identify the type of cargo included
within the shipping unit. The number 3, used in this field, identifies ESDS items, for
example, materiel subject to damage caused by ESD.
5.2 Packaging of ESDS items. In all cases, the first contacting layer (with bare
item) of the selected protective material will be static dissipative and not conductive.
Such a layer may be in the form of a homogeneous single film or cushion thickness, or a
multi-layered structure either as a flat film or cushioning pad as in a pouch configuration.
Shielding will be required to protect against the effects of static discharge. This
protection is normally available in materials through the use of conductive layers attained
by carbon loading metallization or other manufacturing techniques as provided by
MIL-PRF-81705. Selection of the appropriate preservation materials will be based on the
nature of the item and prescribed packaging data. MIL-STD-2073-1 identifies
9
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
procedures for the packaging of ESDS items with the specialized preservation code GX
in table J.Ia, and marking requirements via a special marking code, 39, found in table J.X.
Unpreserved ESDS items should be handled only at an ESD protective workstation by
trained personnel (see Appendix C), who can effectively employ the protective materials
and equipment provided. Only antistatic preservation materials will be used to form the
unit pack. Preserve and pack ESDS items using the following procedures (see figure 2):
b. Place the wrapped or cushioned item in a bag meeting the criteria specified in
MIL-DTL-117, type I, class F, style 1, made from material conforming to MIL-PRF-
81705, type I, class 1 or 2. The bag should be made of one piece of material folded in
half and heat sealed on three sides. This becomes the unit pack holding the ESDS item
and can now be handled as you would any non-ESDS item.
c. Place an ESDS device unit pack label (see figure 3) on the unit pack as
illustrated in figure 4. In the absence of NSNs, local purchase procedures should be
followed when ordering this unit pack sensitive electronic device label. Should this label
be temporarily unavailable, unit packs may be marked on two opposing sides with the
ESDS device symbol and the statement: DO NOT OPEN - EXCEPT AT APPROVED
FIELD FORCE PROTECTIVE WORKSTATION or DO NOT OPEN EXCEPT AT
APPROVED STATIC- FREE WORKSTATION.
d. Most ESDS items (for example, circuit cards, resistors, semiconductors) can
utilize 1 of the 12 reusable PPP-B-1672, type II, style D, folding convoluted fast packs,
which are the only fast packs authorized for ESDS items (see figure 4). ESDS items that
will not fit into 1 of the 12 authorized fast packs will be packed according to prescribed
packaging instructions, or into ASTM D 5118/D 5118M fiberboard containers. Allow for
antistatic cushioning, measure for desired size fiberboard container and refer to the
recommended fiberboard most frequently used container list (see latest revision of
MIL-STD-2073-1). The listed sizes may be requisitioned through normal supply
channels. If box-making equipment is available, containers should be fabricated in
accordance with ASTM D 5118/D 5118M. After closure of carton that was
accomplished in accordance with ASTM D 1974, apply a sensitive intermediate, or
exterior electronic device caution label on the appropriate container (see figures 3 and 4).
Label and mark according to MIL-STD-129.
10
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
5.3 Transporting before final unit pack. If the unit pack needs to be opened for
any purpose, it should be opened at an ESD-controlled workstation (see figure 5). If the
item needs to be transported to several areas before it is converted to a unit pack (for
example, from receiving inspection, to repair and test, to inspection, then to final unit
pack), use the following procedures:
c. Fold the open edge over and place a rubber band around the bag to hold the flap
down. Common adhesive tape should not be used, since it can generate an electrostatic
charge when removed from the roll, or the bag. Antistatic adhesive tape can be used to
hold the flap down.
d. Transport the item by using a covered antistatic tote tray, or by placing the item
in an antistatic type II, style D (folding convoluted), fast pack, PPP-B-1672. Protecting
items in this manner ensures that the item is first placed in an antistatic environment and
then transported.
5.4 Condition code F materiel. All reparable ESDS items should be rendered the
level of packaging that would prevent further deterioration of the item. Returned
condition code F materiel should be given the same applicable packaging referenced on
the preceding pages beginning with paragraph 5.2, for example, condition code A,
repaired, or newly procured ESDS items.
5.5 ESD protective packaging materials. Materials with known NSNs are included
in appendix B. The list may not be all-inclusive because of the rapid technological
changes which affect items available from supply sources.
5.6 The ESD protective worksite. An ESD worksite containing a workstation will
require a minimum floor area of 150 square feet. It is recommended that the workstation
occupy approximately 70 square feet and be centrally located within this site. The outer
perimeter will be identified as a restricted area for trained personnel to handle ESDS
items. This work area will be visibly marked, with overhead sign(s): Caution ESD
Workstation. Figure 5 is a sketch of an ESD-controlled workstation, with items that are
crucial in handling ESDS parts safely. The ionizer is a precautionary device that, within
its effective area of control, will aid in removing electrostatic discharges from
nonconductive surfaces such as the surface of an inadvertently placed Styrofoam cup.
Heel straps and a static dissipative floor mat are also included with the essential worksite
11
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
items. Heat-sealing equipment should be located adjacent to the workbench so that the
wrist strap remains attached while heat-sealing bags. The tabletop and floor mat ground
wires should each go to ground directly (see figure 5, item 6). To prevent the possibility
of shocks from high-voltage sources, wrist straps for use at ESD-controlled workstations
contain a protective resistor (usually one megohm). Grounding points should be
constantly checked for proper grounding.
5.7 Precautions. Observe two basic rules: Handle all ESDS items at a static-
safeguarded worksite and transport all ESDS items in static protective containers or
packages. Adhere to the following precautions when using an ESD-controlled
workstation.
b. Be sure to attach the wrist strap (mandatory) and heel straps (if used) before
handling any ESDS items.
f. If more than one ESD-controlled workstation is located in the same area, do not
connect the tabletops or floor mats grounding points in series; individually ground each
one.
g. Do not use waxes, polishes, or similar material on the floor mat or tabletop.
They may deposit an insulating layer of residue reducing or eliminating the effectiveness
of the floor mat or tabletop. For the same reason, the use of topical antistatic spray is not
recommended on packaging materials.
h. Sweep dust and dirt from the tabletop and floor mat as often as needed to
prevent any accumulation which will also insulate them and make them ineffective.
12
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
j. Check wrist straps daily to ensure that the protective resistor (usually one
megohm) is still in the circuit and that personnel are properly grounded. If the wrist strap
resistance is less than 250K ohms, or indicates an open circuit, do not use it.
5.9 ESD workstation conductive material. The term conductive is often used in
reference to ESD protective tabletops, floor mats, and chairs, but this term is a misnomer.
They are not conductive as are common metals (for example, copper, aluminum, etc.),
but are classified between metal conductors and insulators of electricity such as ceramic,
dry paper, and mica. The resistance characteristics of static dissipative table tops, floor
mats, and chairs prevent the possibility of a spark discharge or high current flow. They
allow an electrostatic charge to be safely dissipated across the surface to the ground.
5.10 ESD field service kit. ESD protection is required where formal workstations
are not practical (that is, remote locations such as shelters and vans). ESD control field
service kits provide the next most effective means of preventing ESD damage. Their
primary use is in support of personnel who remove ESDS items from service or who
place them in operation during which time items are outside of prescribed packaging.
Kits are available which allow protection for ESDS items at the ultimate user level (see
appendix A). Figure 7 reflects a typical kit as described in Appendix A. It is noted that
these static dissipative mats with accessories are not a substitute for a complete ESD
protective workstation. The kit is a field expedient and contains only the minimum
requirements for ESD-control. This supplemental handling procedure for repair type
ESDS items is the only interim technique where the reuse of ESD preservation material is
encouraged.
13
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
6. NOTES
6.1 Intended use. This handbook provides guidance on procedures, materials, and
practices that can be used to protect and extend the service life of ESD sensitive items.
Information is provided on how to receive, handle, pack, mark, and ship ESD items.
6.3 Changes from previous issue. Marginal notations are not used in this revision
to identify changes with respect to the previous issue due to the extent of the changes.
14
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
15
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
Measured voltages
____________________________________
Means of
static generation 10% to 20% RH 65% to 90% RH
________________________________________________________________________
Component Volts
_______________________________________________________________________
Transistors 30-7,000
Operational amplifiers (modules) 200-2,500
Diodes 300-2,500
Film resistors 300-3,000
Low-power, integrated circuit logic 500-2,500
Silicon controller rectifier 700-1,000
16
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
17
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
18
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
19
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
NOTE: Preferred color is yellow hand on black triangle per ASTM D 5445, symbol 28.
Size may vary.
20
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
21
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
22
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
23
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
24
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX A
A.1 SCOPE
A.1.1 Scope. This appendix provides information on the ESD field service kit
(MIL-PRF-87893, type III), its components, and the basic instructions on how they
should be used to handle and protect ESD sensitive items.
A.2 PROCEDURE
A.2.1 ESD protective field service kit instructions. The following steps should be
followed when working with ESD protective field service kit instructions.
CAUTION: Only trained personnel should handle unprotected ESDS items. Disconnect
all power before handling any item.
STEP 1. Place unfolded work mat on table or floor near work area or service location.
NOTE: Remove all ESD packaging material from pockets (A and B) and place away
from mat.
STEP 2. Attach ground cord to mat fastener A or B. Attach bulldog clip to mainframe,
chassis, or other bare metal surface near item to be replaced or removed. This surface has
to be a part of unit to be replaced or removed, and be a part of unit assembly containing
item.
STEP 3. The wrist strap coil containing resistor will be attached to the same mat fastener
as the grounded connectors A or B. Adjust wrist strap over wrist against bare skin.
25
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX A
STEP 4. Proceed now to remove, replace, or handle the ESDS item only on the mat
surface. Keep all other tools or non-ESDS items off the mat.
STEP 5. ESDS items to be returned (for example, condition code F) for repair or
otherwise removed from the static dissipating mat should be packaged to prevent any
further deterioration (see paragraph 5.2). Place item in antistatic pouch D, made from
material conforming to MIL-DTL-81997, type II. Fold over opening and place in
shielding bag E, made from material conforming to MIL-PRF-81705, type I. Fold the
opening, and place a rubber band over this shielding bag. Do not use adhesive tape. Item
can now be handled as you would any other non-ESDS item.
NOTES:
1. Do not disassemble the field service kit until all procedures have been completed.
2. Ground cord and wrist strap cord are usually connected together on the kits ground
snap(s).
3. Follow manufacturers test method and frequency for evaluating the electrical and
mechanical characteristics of wrist strap and ground cord.
26
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX A
27
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX A
NOTES:
1. Use the FEDLOG, any service (for example, Army has a tank icon), to determine
availability (AAC code) and cost of ESD workstation and components. Individual
NIIN/NSN data can be reviewed, or do an Interactive Query. Go to the open field for
Part Number, and print: MILW87893, MIL-W-87893, or MILPRF87893. This is a
specification for ESD workstations, MIL-PRF-87893, Workstation, Electrostatic
Discharge (ESD) Control. Next, place cursor arrow on Search block, bottom right of
screen and click. A screen titled, Part Number Pick List will appear on monitor screen.
Click cursor on, Tag All for Part Numbers available in FEDLOG, bottom left of screen.
Go to top of screen and find the Toolbar Icons (below File bar), click cursor on either
arrow icon, or . Clicking cursor on an arrow ( ) icon will provide data
associated with an NSN in the listing of NSNs associated with this specification.
Decide on what data files you want to review on these NSNs. Click cursor on Data
Views found on the Main Menu bar. Click cursor on Select ViewsF3 and leave the
checkmarks on those NSN data fields that will be reviewed (for example, Army Master
Data (AMDF Management) Data (AAC, Cost, UI), Reference Number Data, Supplier
Data, and Characteristics Data file). The Reference Number Data Response File gives
part numbers used by suppliers (CAGE Code) in their supply catalogs, bulletins,
advertisements. After pertinent data has been reviewed on an NSN, move cursor arrow to
bottom left of screen, point and click on the icon block Next NSN.
2. There is a Qualified Product List (QPL-87893-01, dated 1 May 1995) for ESD
workstation products qualified under the military specification, MIL-PRF-87893. Go to a
search browser on a personal computer (PC) and type in
http://assist.daps.dla.mil/quicksearch/. A screen appears on the PC monitor, Tell Us
What You Want!. At the middle of this page are the words: Document Number
(underlined). Type in the numbers 87893. Click PC mouse on Submit. This action
brings up another web page, look for and click PC mouse on QPL-87893-1. Another
web page is displayed. At the top of this page click PC mouse on icon (picture) of a book
to the left of the words: Click here to access document images. Another web page is
displayed. Go to the lower left of this page and under Media, click PC mouse on the
small icon stating: PDF. This action brings you to a QPL document listing of ESD
workstation components NSNs and approved U.S. Air Force suppliers.
28
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX B
B.1 SCOPE
B.1.1 Scope. This appendix provides National Stock Numbers (NSN) assigned to
approved and tested ESD materials. Barrier and cushioning materials meeting ESD
protective performance criteria are listed under appropriate Federal and military
specifications, and Commercial Item Descriptions (CIDs). The listed NSNs meet the
protective criteria set forth in the identified specifications and CIDs. It should be noted
that NSNs for these specifications are periodically added, or dropped from the FEDLOG
for various acquisition reasons. Therefore, prior to ordering, an NSNs FEDLOG AMDF
Acquisition Advice Code (AAC) should be checked to verify if the item is active, and to
determine how and under what restrictions the item can be acquired.
B.2.1 General. The documents listed below are not necessarily all of the
documents referenced herein, but are those needed to understand the information
provided by this Appendix.
FEDERAL SPECIFICATIONS
29
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX B
30
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX B
NSN SIZE
8135-00-092-3220 3 ft x 600 ft
8135-01-185-6816 3 ft x 150 ft
NSN SIZE
8135-01-158-7786 48 in x 48 in
8135-01-163-3486 24 in x 36 in
NSN SIZE
NSN SIZE
8135-01-087-3602 1 / 4 in x 24 in x 375 ft
8135-01-087-3603 1 / 4 in x 12 in x 375 ft
8135-01-088-3850 1 / 4 in x 48 in x 375 ft
31
Downloaded from http://www.everyspec.com
MIL-HDBK-773
APPENDIX B
NSN SIZE
8105-01-197-2965 12 in x 12 in
NSN SIZE
8105-01-197-2966 10 in x 10 in
8105-01-097-7846 10 in x 12 in
8105-01-215-0462 8 in x 8 in
8105-01-216-7804 8 in x 12 in
8105-01-356-6362 3 in x 5 in
8105-01-360-6563 6 in x 6 in
NSN SIZE
8105-01-096-9527 5 in x 8 in
8105-01-096-9528 12 in x 18 in
8105-01-097-4507 8 in x 12 in
8105-01-119-8109 18 in x 18 in
8105-01-119-8110 10 in x 24 in
8105-01-120-3370 15 in x 18 in
8105-01-120-3371 14 in x 18 in
8105-01-120-3772 12 in x 16 in
8105-01-120-3373 11 in x 15 in
8105-01-120-3374 10 in x 14 in
8105-01-120-3375 10 in x 12 in
8105-01-120-3376 8 in x 10 in
8105-01-120-3377 8 in x 8 in
8105-01-120-3378 6 in x 10 in
8105-01-120-3379 5 in x 10 in
32
Downloaded from http://www.everyspec.com
MIL-HDBK-773
APPENDIX B
8105-01-120-3380 4 in x 6 in
8105-01-120-3381 4 in x 4 in
8105-01-120-3382 3 in x 5 in
NSN SIZE
8105-01-162-2174 6 in x 10 in
8105-01-180-7919 10 in x 12 in
8105-01-181-5534 8 in x 10 in
8105-01-185-2632 24 in x 36 in
8105-01-185-9680 10 in x 16 in
8105-01-217-3773 6 in x 8 in
NSN SIZE
NSN SIZE
8105-01-236-0149 8 in x 12 in
8105-01-236-0150 10 in x 14 in
8105-01-236-5944 4 in x 6 in
8105-01-243-6628 20 in x 14 in
8105-01-243-6629 15 in x 25 in
33
Downloaded from http://www.everyspec.com
MIL-HDBK-773
APPENDIX B
NSN SIZE
8115-00-101-7638 9 in x 6 in x 3 1/2 in
8115-00-101-7647 9 in x 6 in x 2 1/2 in
8115-00-787-2142 6 in x 5 in x 2 1/2 in
8115-00-787-2146 12 in x 8 in x 2 1/2 in
8115-00-787-2147 6 in x 5 in x 3 1/2 in
8115-00-787-2148 12 in x 8 in x 3 1/2 in
8115-01-019-4084 18 in x 12 in x 3 1/2 in
8115-01-019-4085 18 in x 12 in x 2 1/2 in
8115-01-057-1243 13 in x 13 in x 3 1/2 in
8115-01-057-1244 10 in x 10 in x 3 1/2 in
8115-01-057-1245 16 in x 16 in x 3 1/2 in
8115-01-093-3730 24 in x 16 in x 3 1/2 in
8115-01-449-0898 6 in x 9 in x 4 1/2 in
PPP-B-1672, type II, style D, fast packs are used for ESDS items and have the word
antistatic printed on both ends.
NOTES:
1. Acquisition personnel use QPLs to find suppliers for materials that meet performance
criteria specified in the specification. Each military or federal specification, referenced in
this appendix, should be checked to see if the document has a QPL.
34
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX B
After entering either document number, go to the bottom of the left of the new screen,
click mouse on the Tag All icon, and then go to the tool bar menu line, that is, icon line
at the top of the screen with picture of a printer on the extreme left side. Then, go over to
the blue right pointing arrowhead. Click on the right pointing arrowhead. A new screen
appears providing the first listed NSNs AMDF data. Once this data is reviewed for
pertinent information, then look at Characteristics and Reference Number Data Response
Files data for each NSN to find out which, if any, military specification the items
performance characteristics meet; for example, the type, grade, class, style, etc. Once an
NSNs data has been reviewed, go to the bottom of the screen, click on Next NSN bar
to look at another NSNs data, if another exists.
35
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX C
TRAINING
C.1 SCOPE
C.1.1 Scope. This appendix provides information on how to obtain training for the
correct procedures and practices to receive, handle, pack, mark, store, and ship ESD
sensitive items.
C.2.1 General. The documents listed below are not necessarily all of the
documents referenced herein, but are those needed to understand the information
provided by this Appendix.
C.3.1 Sources. Training courses and information for ESD educational programs
are available through the following sources:
36
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX C
b. The SMPT correspondence course titled, Defense Marking for Shipment and
Storage (Course Number 908 F32). This course supplements ESDS item packaging
procedures with DoD item marking requirements. Course enrollment is also through the
ATSC, AIPD, or the following website: http://www.atsc.army.mil/accp/aipdnew.asp.
The mailing address for ATSC is: Department of the Army, Army Institute for
Professional Development, U.S. Army Training Support Center, Newport News, VA
23628-0001.
NOTE: Only questions or comments related to the technical content of the packaging
correspondence courses should be discussed with technical experts at the SMPT. Contact
SMPT by writing to the Dean, School of Military Packaging Technology, ATTN:
ATSL-MPT, Building 360, 360 Lanyard Road, Aberdeen Proving Ground, MD
21005-5001. The school registrars phone number to obtain points of contact is DSN
298-2008 or commercial (410) 278-2008).
C.4.1 Training aids. Video and graphic training aids for local ESD instructional
programs can be obtained through the following sources:
37
Downloaded from http://www.everyspec.com
MIL-HDBK-773A
APPENDIX C
b. The ESD Association has videos that are part of its ESD training and auditing
program. Contact will need to be made with this association to ascertain their procedures
for renting or purchasing ESD videos in their product catalog.
CONCLUDING MATERIAL
Army SM Army SM
Navy AS
Air Force 11 (Project PACK-1118)
DLA DH
Review Activities:
NOTE: The activities listed above were interested in this document as of the date of this
document. Since organizations and responsibilities can change, you should verify the
currency of the information above using the ASSIST Online database at
http://assist.daps.dla.mil.
38