Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
290 views

Network Time Protocol (NTP) Server: 07 April 2016

Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over packet-switched, variable-latency data networks.

Uploaded by

Chandresh Prasad
Copyright
© © All Rights Reserved
290 views

Network Time Protocol (NTP) Server: 07 April 2016

Network Time Protocol (NTP) is a networking protocol for clock synchronization between computer systems over packet-switched, variable-latency data networks.

Uploaded by

Chandresh Prasad
Copyright
© © All Rights Reserved
You are on page 1/ 9

Network Time Protocol

(NTP)Server
[Mini Project]

Prepared By,
Chandresh Prasad (11CO35)
&
Faizan Kazi (12CO35)

07th April 2016

Prepared for,

Network Programming Laboratory

Instructor: SHAIKH ABDUL SALAM


Introduction

Network Time Protocol (NTP) is a networking protocol for clock


synchronization between computer systems over packet-
switched, variable-latency data networks.

Network Time Protocol (NTP) is a protocol that is used to


synchronize computer clock times in a network of computers.

NTP uses Coordinated Universal Time (UTC) to synchronize


computer clock times to a millisecond, and sometimes to a
fraction of a millisecond.

NTP is an Internet Standard Protocol originally developed by


Prof. David L. Mills @ University of Delaware.

With NTP your system's time can be maintained to within


milliseconds of Coordinated Universal Time.

The protocol is usually described in terms of a client-server


model, but can as easily be used in peer-to-peer relationships
where both peers consider the other to be a potential time
source.

Implementations send and receive timestamps using the User


Datagram Protocol (UDP) on port number 123.
Clock strata

NTP uses a hierarchical, semi-layered system of time sources.


Each level of this hierarchy is termed a "stratum" and is assigned
a number starting with zero at the top.

A server synchronized to a stratum n server will be running at


stratum n + 1. The number represents the distance from the
reference clock and is used to prevent cyclical dependencies in
the hierarchy.

Stratum 0
These are high-precision timekeeping devices such as atomic
clocks, GPS clocks or other radio clocks. They generate a very
accurate pulse per second signal that triggers an interrupt and
timestamp on a connected computer. Stratum 0 devices are also
known as reference clocks.

Stratum 1
These are computers whose system clocks are synchronized to
within a few microseconds of their attached stratum 0 devices.
Stratum 1 servers may peer with other stratum 1 servers for
sanity checking and backup. They are also referred to as
primary time servers.

Stratum 2
These are computers that are synchronized over a network to
stratum 1 servers. Often a stratum 2 computer will query several
stratum 1 servers. Stratum 2 computers may also peer with other
stratum 2 computers to provide more stable and robust time for
all devices in the peer group.

Stratum 3
These are computers that are synchronized to stratum 2 servers.
They employ the same algorithms for peering and data sampling
as stratum 2, and can themselves act as servers for stratum 4
computers, and so on.
The upper limit for stratum is 15; stratum 16 is used to indicate
that a device is unsynchronized. The NTP algorithms on each
computer interact to construct a Bellman-Ford shortest-
path spanning tree, to minimize the accumulated round-trip
delay to the stratum 1 servers for all the clients.

Yellow arrows indicate a direct connection; red arrows


indicate a network connection.
Network Protocol Used by NTP

NTP uses UDP/IP packets for data transfer because of


the fast connection setup and response times.
The official port number for the NTP (that ntpd and
ntpdate listen and talk to) is 123.
NTP supports a hierarchy of multiple server levels to
handle a large load of client requests.

NTP Toolkit

The ntpq p command will print out your systems


current time status.
The ntpdc c loopinfo will display how far of the
system time is in seconds, based upon the last time the
remote server was contacted.
The ntpdate d command will contact an NTP server
and determine the time difference but not change your
systems time.
Screenshots

Created Own Server

Checked status of server running ntpq -p command


ntpdate command to get NTP server time

Configured time synchronization on Ubuntu machine


Configured time synchronization on Windows machine

You might also like