GR5 - Quick Start Guide

P O S I T I O N I N G S Y S T E M S
GR-5
Quick Start Guide
Part Number 7010-1022

Rev A
Copyright Topcon Positioning Systems, Inc.

August, 2011
All contents in this manual are copyrighted by

Topcon Positioning Systems, Inc.
All rights reserved.
This quick start guide tells you how to

get started using the GR-5 receiver.
Terms and Conditions
Thank you for buying this Topcon product. This manual has been
prepared to assist you with the care and operation of the product and
its use is subject to these Terms and Conditions and those more fully
set forth in the Operators/Users Manual.
Usage and Safety
This product is designed for use by professionals. Always use safety
precautions when operating this or any Topcon product.
Copyrights and Trademarks
The information in this manual is a copyright of Topcon and is for use
only with the product. GR-5, TRU, TopSURV, Topcon Link, Topcon
Tools, and Topcon are trademarks or registered trademark of Topcon
Positioning Systems, Inc. Windows and the Windows CE icon are
registered trademarks of Microsoft Corporation.
Other product and company names mentioned herein may be
trademarks of their respective owners.
Disclaimer of Warranty and License
Agreement
Please see the Operators/Users Manual for detailed information on
warranties and the license agreement which may apply to the Product.
EXCEPT FOR SUCH WARRANTIES AND LICENSES PROVIDED WITH
THE PRODUCT, THIS MANUAL AND THE PRODUCT ARE PROVIDED
AS-IS. TOPCON AND ITS DISTRIBUTORS SHALL NOT BE LIABLE
FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED
HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE FURNISHING, PERFORMANCE OR USE OF THIS
MATERIAL OR THE PRODUCT.
Use of any computer programs or software supplied by Topcon or
downloaded from the Topcon website in connection with the Product
implies acceptance of the Terms and Conditions here and in the
Operators/Users Manual.
ECO#4187
Table of Contents
Introduction .............................................1
Chapter Descriptions ...........................................1
Where to Find More Information ........................2
Getting to Know Your GR-5 ...............................3
MINTER .......................................................3
Data and Power Ports ....................................9
Radio Antenna and Pole Connectors ............11
SDHC and SIM Card Slots ...........................11
Default Configuration ..........................................13
Accessories ..........................................................16
Getting Started ........................................21

Installing Software ...............................................21
Installing PC-CDU ........................................22
Installing TRU ..............................................22
Turning On/Off the Receiver ...............................23
Installing the SDHC Card ....................................23
Installing the SIM Card .......................................24 i
Installing the Batteries .........................................25
P/N 7010-1022 www.topconpositioning.com

Contents
Attaching the Batteries ..................................25

Detaching the Batteries .................................27
Charging the Batteries .........................................27
Charging with the Power Supply Unit ..........28
Charging with the Battery Charging Cradle .29
Charging Temperatures .................................29
Estimated Operating Times ................................30
Connecting the GR-5 with a Control Device ......31
Establishing an RS232 Cable Connection ...........32
Surveying ................................................35
Post-Processing Survey .......................................35
Step 1: Set up the GR-5 Base ........................35
Step 2: Set up the GR-5 Rover ......................37
Step 3: Measure Antenna Height (for Base and
Rover) ........................................................38
Step 4: Collect Data (for Base and Rover) ....39
Amount of Memory Required to Store a One
Hour File ..................................................41
RTK Survey .........................................................42
Step 1: Repeat Steps 1 through 3 in Post-
Processing Survey on page 35 .................42
Step 2: Connect a Hand-Held Controller ......42
ii Step 3: Start Surveying with TopSURV .......42
Topcon GR-5 Quick Reference Guide

Contents
Downloading Files ..................................45

Downloading Files via Topcon Link ...................45
...Using Windows Explorer ...........................45
...Using Topcon Link ....................................47
Downloading Files Using TRU ...........................48
Maintenance ............................................49
Restoring Default Settings ...................................49
Performing Hardware Reset ................................49
Clearing the NVRAM ..........................................50
Initializing File System ........................................51
Managing Receiver Options ................................51
Checking the Receivers OAF using TRU ....52
Loading an OAF using TRU .........................52
Deleting Files from the Internal Memory Card ...53
Recovering Deleted Files ....................................53
Activating Sleep Mode ........................................54
Loading New Firmware .......................................55
Troubleshooting .....................................65
Check This First! .................................................65
TX RX LED Blink Pattern on Error Conditions .66
iii

Contents
Obtaining Technical Support ...............................68

End-users .......................................................68
Dealers (in the U.S., Canada, Australia) .......68
Help Desk 68
Phone 68
Email 69
Dealers (International) ..................................69
iv
Topcon GR-5 Quick Reference Guide

Chapter 1
Introduction
This quick start guide focuses on how to get your GR-5 up
and running quickly without overwhelming you with
technical details.
Chapter Descriptions
Chapter 1: Introduction (this chapter)
Understand the GR-5 parts and features, default
configuration, and accessories available for your GR-5
receiver.
Chapter 2: Getting Started
Explore preliminary steps to get your GR-5 ready for
surveying.
Chapter 3: Survey
Learn the basic survey procedures.
Chapter 4: Downloading Files
Transfer field data to your post-processing software.
Chapter 5: Maintenance
1
Help you use the GR-5 productively and safely.

Introduction
Chapter 5: Troubleshooting
Provide tips and solutions for potential problems during
GR-5 operation.
Where to Find More Information

For detailed information regarding features, capabilities,
and software introduced with this receiver, refer to the
GR-5 Operators Manual (7010-1004).
For the quick guide about GR-5 cellular modem, refer to
the GR-5 Cellular Modem Quick Start Card
(7010-1013).
Visit Topcon University at www.topconuniversity.com
for webinars and training opportunities. The TU website
also provides you with access to software and firmware,
manuals, and more to help you maximize your technical
and industry knowledge and skills.
Topcon GR-5 Quick Start Guide

Getting to Know Your GR-5

MINTER
The MINTER is the receivers minimum interface used to
display and control data input and output.
REC RX TX
STAT BT
FUNCTION
FUNCTION
Battery Battery
Power FUNCTION
Button Button
The battery LEDs display the power status for each

battery:
Green indicates greater than 85% charge.
Orange indicates an intermediate charge.
Red indicates less than 15% charge.
The STAT LED displays the status of tracked satellites.

Red blink receiver is on, but no satellites being
tracked.
3

Introduction
Green blink receiver is on and tracking satellites; one

blink per tracked GPS satellite.
Orange blink receiver is on and tracking satellites; one
blink per tracked GLONASS satellite.
The REC LED displays the data recording status.

Green blinks each blink indicates that data is being
written to the SDHC card.
Solid Orange the receiver is changing modes.
Orange blinks the receiver is checking its internal file
system. During this operation, the file system is not
accessible for CDU (control display unit) applications
or for data recording. This operation may require from
fractions of a second to several minutes, depending on
the circumstances and the amount of internal memory.
Solid Red a fault condition with the receiver (no more
memory, no SDHC card inserted, a hardware problem,
or an improper OAF).

The RX TX LED displays the status of the modem.

Table 1-1 describes the LED colors and patterns for the
different modems available for the GR-5 receiver.
Table 1-1. RX TX LED Indications
No light modem is turned off.
Green flashes modem is in receiver mode.
Solid Green a radio link has been established;
modem is ready to receive data.
Solid Green plus Red flashes modem is receiving
FH915 Plus/ data.
Digital/Satel Solid Red modem is in transmitter mode.
Modems
Red flashes a fault condition has been detected.
Check the condition of the radio modems antenna to
ensure it is undamaged, and is connected properly and
securely. Also make sure nothing interrupts the signal.
Red flashes plus Green flashes modem is in
command mode.
Solid Orange (Red and Green) the modem is
initializing.
Green flashes the modem is on, registered on the
network, and is waiting for incoming calls (Slave
mode).
GSM/GPRS
Solid Red a connection has been established.
Green flashes the modem is in direct control mode
(Daisy Chain).
Orange flashes an error has occurred (initialization 5
error, wrong PIN code, and so forth).

Introduction
The BT LED indicates the level of activity at the Bluetooth

wireless technology communication link:
Blue flashes the Bluetooth module is on but no
connection is established.
Solid blue light the Bluetooth module is on and a
connection has been established.
No light the Bluetooth module is off.
The power button turns the receiver on and off.
The FUNCTION button switches the receiver between

information modes and post-processing modes, starts/stops
data recording, and changes the baud rate of the serial port A
to 9600. Table 1-2 on page 7 describes the REC LED status
when using the FUNCTION button.

Table 1-2. FUNCTION Button Operations and REC LED Status
FUNCTION
REC LED Status
Key
When data recording is off, and the FUNCTION key is...
No light No data recording.
Orange Internal file system test in progress.

Not pressed
blink
Red No free memory; hardware problem with

data recording. No SDHC card.
If FUNCTION key mode is LED blink mode switch
Orange Release to change information mode.

Pressed for
< 1 second If FUNCTION key mode is Occupation mode switch
Orange No function.
Green Release to start data recording (post-

Pressed for
processing occupation mode undefined).
15 seconds
If FUNCTION key mode is Occupation mode switch
Green Release to start recording (Kinematic or

Static post-processing occupation mode). 7

Introduction
FUNCTION
REC LED Status
Key
Pressed for Red Release to turn serial port A baud rate to

58 seconds 9600 bps.
Pressed for No light No function.

> 8 seconds
When data recording is on, and the FUNCTION key is...
Red No free memory; hardware problem with

data recording.
Green Data recording started (post-processing

occupation mode undefined).
Not pressed
Green Data recording started (Kinematic post-

processing occupation mode).
Orange Data recording started (Static post-

processing occupation mode).

FUNCTION
REC LED Status
Key
Orange Release to change information mode.

Pressed for
< 1 second
Orange Release to toggle between Static and

Kinematic post-processing modes.
Pressed for No light Release to stop data recording.

15 seconds
Pressed for Red Release to turn serial port A baud rate to

58 seconds 9600 bps.
Pressed for No light No function (data recording still on).

> 8 seconds
Data and Power Ports

The GR-5 has the following three ports:
USB rimmed in yellow; used for high-speed data
transfer and communication between the receiver and an
external device.

Introduction
Serial Port A rimmed in black; used for

communication between the receiver and an external
device.
Power rimmed in red; used to connect the receiver to
an external power source. This port can also be used to
charge the batteries.
USB Serial A Power

(yellow) (black) (red)
S
E P
U R O
S W
B I E
A R
L
The following ports are used internally:

Serial Port B left free in the current release.
Serial Port C connect the modem and receiver boards.
Note that the GSM/GPRS/CDMA modem is located on
the RF modem board.
Serial Port D connect the receiver board and Bluetooth
module. Note that the Bluetooth module is located on
the RF modem board.
10

Radio Antenna and Pole Connectors

The SS antenna connects to the external antenna connector
on the GR-5 radome. The radio antenna uses a reverse
polarity TNC connection or BNC connection depending on
the installed radio modem.
The bottom connector connects the receiver to either a
standard 5/8'' thread pole/adapter or the quick disconnect.
External
Antenna
Connector
Bottom Connector for
Standard Setups
SDHC and SIM Card Slots

The SDHC and SIM card slots reside under the batteries near
the base of the dome.
The SDHC card slot is located to the left of the MINTER

inside the battery pocket and connects an optional SDHC
card to the receiver board to provide memory. The data that
resides on the SDHC card can be accessed via the USB or
11

Introduction
serial port, or Bluetooth. The following industrial-grade

cards were tested in the temperature range -30C to 60C (-
22F to 140F).
Transcend Ultra Industrial 2 GB
APRO Industrial 4GB
SanDisk Ultra II
Swissbit Industrial 2GB
Before using any other SDHC cards, consult with TPS
technical support about compatibility.
The SIM card slot is located to the right of the MINTER

inside the battery pocket and allows a standard SIM card to
be installed in the receiver. Once installed, the SIM card
provides a unique identification for the receivers GSM
module and enables the receivers GSM functionality based
on the subscribed services. The GSM module with the SIM
card installed can be configured via TRU. A SIM card can be
purchased from a local cellular provider.
12

Default Configuration
Battery
SIM Card
SDHC Card
Battery
The GR-5 is shipped from the factory with the default
configuration. The following table shows the major default
settings for the GNSS board.
Parameter Default Setting
MINTER:
Recording interval 1 second
Elevation mask 5 degrees
Filename prefix log

13

Introduction
Tracking:
GPS tracking enabled*
GLONASS tracking enabled*
SBAS tracking disabled*
Positioning:
Mode standalone
PDOP mask 30
GPS usage enabled*
GLONASS usage enabled*
Multipath reduction enabled*
Raw measurement update rate 100* ms
Position update rate 100* ms
Datum W84
14

RTK:
Position output mode Delay
Ambiguity fixing level Medium
Max number of SVs in RTK 20
Minimum C/A SNR 31 dB*Hz
Min number of SVs for fixing 5

ambiguities
Max extrapolation time 30 seconds
Serial Ports (A, B, C, D)*:
Input mode Command
Baud rate 115200
Hardware handshaking Disabled
Stop bits 1
Parity No parity
Data bits 8
*. Some of the default settings depend on the

options available in the OAF for your GR-5 15
and may differ from the published values.

Introduction
The modem default settings vary greatly depending on the

modem type, country of usage, etc. Consult the Operators
Manual for details.
Accessories
The following accessories are available for the GR-5
receiver.
Accessory Part Number Description
Cables
Power cable U.S. 14-008052-01 Connects the power

Europe 14-008054-01 supply unit to a
Australia 14-008053-01 grounded outlet.
Receiver power/ 14-008016-03 Connects the receiver

charging cable and the power supply
unit via SAE
connectors for battery
charging.
USB cable 14-008070-01 Connects the receiver

to an external device
(controller or
computer) for high-
speed data transfer
and receiver
16 configuration.

Accessories
Serial cable 14-008005-02 Connects the receiver

to an external device
(controller or
computer) for data
transfer and receiver
configuration.
ODU-to-alligator 14-008097-01LF Connects the charging

clips cable cradle or receiver to
an auxiliary battery
for powering the
receiver during survey
operations.
Cradle-to- 14-008072-01 Connects the receiver

receiver charging (1.5m long) to the charging cradle
cable 14-008072-02 for external power.
(0.5 m long)
Chargers
Power supply 22-034101-01 Charges the batteries.

unit
Charging Cradle 01-050911-01 Charges the batteries.
Antennas
SS/GSM antenna 30-030012-01 The Spread Spectrum

and GSM antenna. 17

Introduction
UHF/GSM 30-070003-01 The UHF and GSM

antenna UHF 410-440 antenna.
30-050503-01
UHF 450-470
Tripods, Poles, Adapters
Tripod 22-050501-01 The heavy duty

tripod.
Pole 22-050908-01
Universal 22-006008-01 Used to level the

tribrach and 22-006009-011 tripod and secure the
tribrach adapter receiver or antenna to
the tripod.
Precision tribrach Used to precisely

adapter center, align, and
level the tripod over a
point.
Quick disconnect 02-850905-01 Connects to the range

adapter pole for the receiver
to slip into the top.
18

Accessories
Miscellaneous
AA battery pack Holds four AA

batteries to provide a
portable backup
power source for the
receiver
19

Introduction
Notes:
20

Chapter 2
Getting Started
This chapter describes the activities you normally need to
take when you start using the GR-5 for the first time or
before beginning to survey with the GR-5 receiver,
specifically:
installing configuration software
turning the receiver on and off
inserting SDHC and SIM cards
charging and attaching batteries to the receiver
connecting the receiver and an external control device
Installing Software
The Topcon GPS+ CD includes the following software
programs used for configuring and maintaining the receiver.
This software is also available on the TPS website to
registered users.
If installing the program(s) from the GPS+ CD, insert the
CD into the computers CD-ROM drive. If downloading the
program(s) from the website, extract the programs files into
a folder on the hard drive. 21

Getting Started
Installing PC-CDU
1. Create a PC-CDU folder on the hard drive and place the
compressed PC-CDU zip file (retrieved from either the
website or the GPS+ CD) in this folder.
2. Navigate to the PC-CDU folder and double-click the
PCCDU_MS zip file.
3. Extract the PCCDU.EXE and associated *.dll file to the
PC-CDU folder.
4. Create a shortcut on the computers desktop for quick
access to PC-CDU.
To uninstall PC-CDU, navigate to the location of the *.exe
file. Select the file and press Delete.
Installing TRU
1. Navigate to the TRU folder, and double-click TRU.zip.
2. Extract TRU.exe to the TRU folder.
3. Double-click TRU.exe to run the installer, and then
follow the on-screen instructions.
After installation, shortcuts appear on the desktop and in the
TRU menu.
To uninstall TRU, use Add or Remove Programs in
Windows Control Panel. navigate to the location of the
*.exe file.
22

Turning On/Off the Receiver
Turning On/Off the Receiver

To turn ON the receiver, press and hold the power button
until the LEDs briefly flash.
To turn OFF the receiver, press and hold the power button
for more than one and less than four seconds (until both the
STAT and the REC LEDs are off).
Installing the SDHC Card

The SDHC card provides memory space in which to save
logged data. Although you may install an SDHC card of any
size, the receiver will recognize only up to 2 GB of memory.
Always initialize the file system on the installed SDHC card
before the first use. Initialization procedure is described in
Initializing File System on page 51.
1. Ensure the receiver is turned off.
2. Remove the battery to the left of the MINTER.
3. Carefully insert the SDHC card, label side down, into
the SDHC card slot located at the top of the battery
compartment.
23

Getting Started
Once the receiver is turned on, the receiver board will detect
the SDHC card and it will be ready to use as needed.
Installing the SIM Card

The SIM card provides access to communication over GSM,
GPRS, or CDMA services. The SIM card must support
Circuit Switched Data to communicate directly between
receivers. The SIM card must have GPRS support to
communicate over a TCP/IP network.
1. Ensure the receiver is turned off.
2. Remove the battery to the right of the MINTER.
24

Installing the Batteries
3. Carefully insert the SIM card, label side up, into the
SIM card slot located at the top of the battery
compartment.
Once the receiver is turned on, the receiver board will detect
the SIM card and it will be ready to use as needed.
Installing the Batteries

Attaching the Batteries
To attach the batteries to the GR-5:
1. With the battery slightly tipped, place the bottom of the
battery into the bottom of the battery compartment. 25

Getting Started
2. Gently push the top of the battery into the battery

compartment until it snaps into place. Make sure that the
clip at the top of the battery completely snaps into place.
26

Charging the Batteries
Detaching the Batteries

To detach the batteries from the GR-5, so that they can be
charged or replaced:
Using the clip at the top of the battery, gently pull down and
out to detach the battery from the receiver.

You can charge the batteries using the power supply unit or
the battery charging cradle.
A 6-hour charge cycle will fully charge the batteries; the
batteries charge simultaneously.
The Li-Ion batteries used in the battery packs should run at
no less than 80% capacity after 500 charging cycles. These
batteries do not need to be drained before recharging.
27

Getting Started
Charging with the Power Supply Unit
CAUTION CAUTION
The power supply unit is designed for
indoor use only. Do not use it in damp or
wet environment. Do not expose the power
supply to rain or snow. It should only be
used for charging the batteries. Do not use
as a power source during surveying.
The power supply unit can be connected to the charging

cradle or directly to the GR-5. The power supply has the
following specifications:
input voltage between 100 and 240 V AC
frequency of input power between 50 Hz and 60 Hz
output voltage 12 V DC@2.5 A (30 W)
To charge the attached batteries using the power supply unit:
1. Plug the receiver-to-SAE power cable into the
receivers power input port.
2. Connect the receiver-to-SAE power cable and the
power-to-outlet cable to the AC adapter.
3. Plug the power supply-to-outlet cable into an available
outlet.
28

Charging with the Battery Charging Cradle

1. Remove the batteries from the receiver and insert them
into the charging cradle.
2. Connect the power cable to the power supply unit.
3. Connect the SAE connectors on the power adapter cable
and power supply unit.
4. Connect the power adapter cable to one of the ports on
the charging cradle (either port will charge both/either
battery).
5. Plug the power supply to an available outlet.
To grounded outlet
Charging Temperatures
Charge the batteries only in temperatures between 29
32oF (0oC) and 113oF (45oC). This is important to prevent

Getting Started
serious damage to the batteries, the receiver or injury to

persons.
An optimal charging temperature is between 50oF (10oC)
and 77oF (25oC). If possible, charge the batteries within this
temperature range.
Estimated Operating Times

Common Conditions: Bluetooth = on; 10-12 SV tracked; using the
detachable batteries; room temperature
For the GR-5 with FH915+ Modem

Receive only mode 14 hours
250mW transmission mode 12 hours*
1W transmission mode 10 hours*
GSM/GPRS in urban areas 13 hours
For the GR-5 with Digital Modem
0.5W transmission mode 12 hours*
For the GR-5 with Satel Modem
30 0.5W transmission mode 12 hours*

Connecting the GR-5 with a Control Device

Common Conditions: 1012 SV tracked; using the detachable batteries;
room temperature
For the GR-5 with Any Modem

Modem off 20 hours
Common Conditions: 1012 SV tracked; using the battery shells and
AA batteries; room temperature
For the GR-5 with Any Modem

Modem off 2.5 hours
*. At 1 Hz correction rate, charger off.
Connecting the GR-5 with a Control

Device
You can connect the GR-5 with a computer or hand-held
controller to configure, manage files, or maintain the
receiver.
Topcons TRU and PC-CDU software products provide an
interface for various configuration, monitoring, and
management functions for the receiver.
TopSURV field software is used for surveying, common
layout, and GIS purposes and is available for hand-held
controllers.
31
The following connection methods are available:

Getting Started
an RS232 cable and a computer/controller

a Bluetooth-enabled external device (computer/
controller)
a USB cable and a computer/controller with the TPS
USB driver installed (for PC-CDU only)
Establishing an RS232 Cable

Connection
This section shows you how to connect the GR-5 and a
computer/controller running TRU. See RTK Survey on
page 42 for TopSURV connection details.
1. Using the RS232 cable, connect the serial port of the
computer/controller to the receivers serial port.
2. Press the power buttons on the receiver and computer/
controller to turn them on.
3. Start TRU on your computer/controller.
4. Select DeviceApplication ModeReceiver
Managing.
5. Click DeviceConnect.
6. On the Connection Parameters dialog box, select the
following parameters:
Connect Using select Serial Port
Port name shows physical and friendly name for
32 the port. The Application remembers the last used

Establishing an RS232 Cable Connection
transport, and the last successful port/device name

for every transport, so it is easy to connect to the
same device.
If necessary, use the list button on the right of the
Port name field to choose a port from the Select a
Port dialog.
7. Click Connect.
8. Once a TRU connection with the receiver has been
established, the Tools become active and you can
continue with configuration activities.
To quit TRU, click DeviceDisconnect, then
DeviceExit.
33

Getting Started
Notes:
34

Chapter 3
Surveying
This chapter describes how to start surveying using a pair of
GR-5 receivers for post-processing and RTK.
Post-Processing Survey
Step 1: Set up the GR-5 Base
1. Install a heavy duty tripod (PN: 22-050501-01)
over a known point. You do not need universal
tribrach and tribrach adapter when working with
this tripod.
2. Attach the antenna to the modem antenna
connector. This step ensures the safety for the
modem board, even if you does not use it for
transmitting data.
TIP TIP
You can extend the receiver operating
time for post-processing survey by turning 35

Surveying
off the modem board. Connect to the GR-

5 via TRU, click Receiver Settings ->
Power, and set 2 to n in the Slots area.
Note that this will also turn off Bluetooth.
3. Carefully level the tripod and tighten the screws.
4. Attach any other accessories as needed (for
example, a backup power supply).
36

Step 2: Set up the GR-5 Rover

1. If needed, attach the quick disconnect to the bipod/
range pole.
NOTICE
Use a bipod during post-process surveys to
ensure the antenna/receiver does not move
during data logging.
2. Attach the GR-5 receiver to the quick disconnect.

Make sure the receiver locks into place.
3. Attach the antenna to the modem antenna
connector. This step ensures the safety for the
modem board, even if you does not use it for
receiving data.
37

Surveying
GR-5 Recevier
Quick Disconnect (Optional)
5/8 inch Screw
Lock
Step 3: Measure Antenna Height (for Base

and Rover)
1. Measure the antenna height above the control point
or marker, either the slant height or the vertical
height. You may either measure the vertical height
to the Antenna Reference Point (ARP) located at
the bottom of the GR-5, or measure the slant height
38

to the Slant Height Measurement Mark (SHMM) on

the side of the enclosure.
85.0mm
253.0mm
228mm
228mm
228mm
A
168mm
B
A = ARP to edge = 79.0

B = ARP to corner = 97.5
Slant Height
to Base of Vertical Height
Corner on to ARP
Gray Bumper
Station Marker
or
Tip of RTK Pole
2. Record the antenna height, points name, and start

time in the field notes.
Step 4: Collect Data (for Base and Rover)

1. Turn on the receiver. The STAT (status) light
(LED) initially blinks red.
39

Surveying
2. Once the receiver has locked on to one or more

satellites, the STAT light blinks green for GPS
satellites and orange for GLONASS satellites. A
short red blink indicates that the receiver has not
solved a position.
3. Once the short red blink is gone, the receiver has a
position and surveying can begin; wait for green
and orange lights before beginning data collection.
This ensures that the receiver has the correct date
and time, and is locked on to enough satellites to
ensure good quality data.
The process of locking on to satellites normally
takes less than one minute. In a new area, under
heavy tree canopy, or after resetting the receiver, it
may take several minutes.
4. To begin collecting data, press and hold the
FUNCTION key (for more than one second and
less than five seconds).
5. Release the FUNCTION key when the REC
(recording) LED turns green. This indicates that a
file has opened and data collection has started. The
REC LED blinks each time data is saved to the
internal memory.
6. When finished, press and hold the FUNCTION key
40 until the REC LED light goes out.

7. To turn off the receiver, press and hold the power

key until all lights go out, then release.
Amount of Memory Required to Store a One

Hour File
Recording Interval (seconds)

#SVs
0.1 1 5 15 30
Single-frequency dual-system receiver

Memory needed to record data
6 11 MB 1.1 MB 221 KB 74 KB 37 KB
10 14 MB 1.4 MB 283 KB 94 KB 47 KB
14 17 MB 1.7 MB 345 KB 115 KB 57.5 KB
18 20 MB 2 MB 407 KB 136 KB 68 KB
Dual-frequency dual-system receiver

Memory needed to record data
6 17 MB 1.7 MB 347 KB 116 KB 58 KB
10 23 MB 2.3 MB 471 KB 157 KB 78.5 KB
14 29 MB 2.9 MB 595 KB 198 KB 99 KB
18 35 MB 3.5 MB 720 KB 240 KB 120 KB 41

Surveying
RTK Survey
Step 1: Repeat Steps 1 through 3 in Post-
Processing Survey on page 35
NOTICE
Do not turn off the modem board.
Step 2: Connect a Hand-Held Controller

You can connect the controller to the receiver with a
serial cable.
If the controller is Bluetooth enabled, you can connect
it to the receiver wirelessly using TopSURV.
Set the Instrument type to GPS and check the
Bluetooth option in the Connections screen of
TopSURV.
To change the Bluetooth device that the controller
is connected to, click the Connection icon in the
upper-right corner of the main screen in TopSURV.
Step 3: Start Surveying with TopSURV

1. Create a GPS+ job. A user-friendly Wizard will
guide you through the steps to create a job
configuration.
42

RTK Survey
2. After creating a job with the desired configuration

in TopSURV, you can begin the survey.
Job configuration settings will be applied to the
Base receiver only after starting the Base and to the
Rover receiver only after selecting a survey option.
NOTICE
For more details about how to create and
configure a job, start the GR-5 as a base or
rover receiver in RTK and other survey
methods, see the TopSURV Users Manual.
43

Surveying
Notes:
44

Chapter 4
Downloading Files
This chapter describes downloading GNSS data files to a
computer.
After completing a survey, download data files to a
computer for storage, post-processing, or backup. TRU and
Topcon Link both provide file managers to download files
from the receiver to a computer.
Downloading Files via Topcon Link

Topcon Link provides two options for downloading files
from a receiver: via Windows Explorer or via the Topcon
Link interface.
...Using Windows Explorer

1. Connect your receiver and computer.
2. Open Windows Explorer and click the Topcon GNSS
Receivers folder. Right click the folder and select
Explore. The right panel of the window displays the
automatic start of searching for Topcon receivers
connected to any of the computer ports (COM and 45
USB).

Downloading Files
When finished, all receivers connected to the computer

ports display.
3. To view information about the receiver, right-click the

receiver, and select the Properties option.
46
4. To view the raw file, double click on the receiver.

Downloading Files via Topcon Link
To import the file(s) from the receiver to a folder, select

the file(s), and copy to the folder using drag-and-drop
method.
...Using Topcon Link

1. Connect your receiver and computer.
2. To start Topcon Link, click the Import from Device
button on the Toolbar.
3. From the left panel of the Import from Device dialog
box, double-click Topcon Receivers.
The program automatically searches for Topcon

receivers connected to the computer ports (COM and
USB). When finished all receivers connected to the 47
computer ports display.

Downloading Files
4. In the right panel of the Import From Device window,

navigate to and select, or create, a folder to save the
files.
5. To view the collected raw file, double click (or click
Select in the pop-up menu) the receiver. To import the
file(s) from the receiver to the computer and to save in
the selected folder, highlight the file(s) and click the
double arrows.
6. The import in progress displays.
Downloading Files Using TRU

1. Connect the receiver to a computer and run TRU.
2. Click the File Explorer icon in the main window. The
File Explorer dialog box displays all logged raw data
files.
3. To save a file to the computer, highlight the desired file,
right click and select Download from the pop up menu.
In the Save As dialog box navigate to or create a folder
48 in which to download and store the file. Click the Save
button to download and save the file.

Chapter 5
Maintenance
Restoring Default Settings
Most of the settings in the GR-5 have default values, which
you may change as needed for your particular application.
You can always return the receiver to a known operating
condition by restoring its default configuration.
To restore default settings, run TRU and select
ToolsFactory Reset.
Performing Hardware Reset

You can reset the GR-5 without returning any configured
settings to their default values. It may become necessary to
reset the GR-5 to apply certain settings which require a
hardware reset or as part of troubleshooting.
To reset the receiver, run TRU and select ToolsReset
Receiver.
49

Maintenance
Clearing the NVRAM

The receivers Non-Volatile Random Access Memory
(NVRAM) holds ephemeris data, position, the current
boards settings, such as data recording interval, elevation
masks, etc.
After clearing the NVRAM, your receiver will require some
time to collect new ephemerides and almanacs (around 15
minutes).
Clearing the NVRAM will also reset the receiver to factory
default settings.
To clear the NVRAM using the MINTER, take the following
steps:
1. Press the power key to turn off the receiver.
2. Press and hold the FUNCTION key.
3. Press and hold the power key for about one second.
Release the power key while continuing to hold the
FUNCTION key.
4. Wait until the STAT and REC LEDs are green
5. Wait until the STAT and REC LEDs blink orange.
6. Release the FUNCTION key while the STAT and REC
LEDs blink orange.
To clear the NVRAM using TRU, select ToolsClear
NVRAM.
50

Initializing File System
Initializing File System

The memory card in the GR-5 must be initialized before its
first use. Initializing your memory card while in the receiver
will ensure the card is formatted to the TPS proprietary file
system (TPFS). This file system allows the receiver to
create, store, retrieve, delete, and restore the raw data files.
It is also advisable to reinitialized the memory card
periodically (e.g., quarterly). This will erase any data on the
card, check for bad blocks, and set it up afresh.
To initialize the file system, run TRU, select File Explorer,
right-click (on a computer) or click and hold (on a controller)
within the file list on the Files tab and select Initialize File
System.
Initializing the file system of a connected receiver will erase
all of the receivers data files.
Managing Receiver Options

The Option Authorization File enables certain functions,
features, and options in the receiver, such as the following:
the type of signal (L1, L1/L2, and so on) the receiver
processes
the amount of data the receiver stores in the memory
multipath reduction technology
For a complete list of available options and details, consult 51
with a TPS dealer.

Maintenance
Checking the Receivers OAF using TRU

1. Connect the receiver to a computer/controller and
run TRU.
2. Click the Options icon in the main window. The
Receiver Options dialog box displays that allows
the user to view the current authorization options
and upload new ones.
Loading an OAF using TRU

1. Connect the receiver to a computer/controller, run
TRU, and select Options.
2. Click Upload OAF at the bottom of the Receiver
Options dialog box.
3. Navigate to the location of the new Option
Authorization File. OAFs have .jpo or .tpo
extensions and are unique to each receiver.
4. Select the appropriate file and click Upload to the
Receiver. The new receiver option loads onto the
receiver and the Option Manager table updates.
5. When finished, click Save Profile on the Receiver
Options dialog box, then click FileDisconnect to
prevent conflicts with serial port management.
52

Deleting Files from the Internal Memory Card
Deleting Files from the Internal

Memory Card
A memory card holds a finite amount of collected data. To
free up space for more or new data, delete old data.
1. Connect the receiver to a computer/controller and run
TRU.
2. Click the File Explorer icon in the main window.
3. Highlight a desired file in the File Explorer dialog box,
right-click (on a computer) or click and hold (on a
controller) and select Delete from the pop-up menu.
Click Yes to confirm the deletion.
Recovering Deleted Files

The TPS file system is designed to allow you to recover
deleted files. The operation is easy, fast, and secure without
the need for a data recovery software.
1. Connect the receiver to a computer/controller and run
TRU.
2. Click the File Explorer icon in the main window.
3. Right-click (on a computer) or click and hold (on a
controller) within the file list on the Files tab and select
Mode of operationDeleted Files Recovery.
The receiver starts remounting the file system for
displaying deleted files. During this process the REC 53

Maintenance
LED blinks orange. Once the file system is successfully

remounted, the REC LED stops blinking and the deleted
files will appear in the list of existing files.
NOTICE
NOTICE
In this mode, only the deleted file(s) will
display.
To restore the file system to its normal state, select Mode of
operationNormal.
Activating Sleep Mode

You can put the GR-5 into a dormant state to minimize
power consumption without turning off the receiver
completely. In sleep mode, the power board and Bluetooth
module continue to draw a small amount of power from the
batteries, causing the batteries to slowly drain over time.
1. Turn on the receiver.
2. Press the receivers power key for more than four
seconds and less than eight seconds. The STAT LED
will be orange. The receiver enters Sleep Mode.
You can awaken the receiver by turning it on manually or by
sending any number of characters on one of the receivers
54 serial ports.

Loading New Firmware
Loading New Firmware

Receiver GNSS firmware is released as a compressed file
that the user download and decompress. This file contains
the following three files:
ramimage.ldr the Receiver board RAM file
main.ldp the Receiver board Flash file
powbrd.ldr the Power board RAM file
To upload firmware files to GR-5 receiver, follow the steps
below:
1. Connect the receiver to a computer and run TRU.
2. Click the Firmware Loader icon in the main window.
3. Select Receiver/Modem in the Device field of the
Upload Firmware window.
4. Set the Capture Method to Soft Break
(recommended). Browse for and select the receiver
boards RAM file and Flash file.
5. Click Start to upload the selected files.
6. Click OK to complete uploading new firmware to the
receiver.
55

Maintenance
Notes:
56

Chapter 6
Troubleshooting
This chapter provides general tips for diagnosing and solving
some common problems you may encounter while using the
GR-5. For more in-depth troubleshooting, see the GR-5
Operators Manual.
Check This First!

Before contacting Topcon Technical Support, check the
following:
Check all external receiver connections carefully to
ensure correct and secure connections. Double check for
worn or defective cables.
Check all power sources for drained batteries or
incorrectly connected batteries/cables.
Check that the most current software is downloaded
onto the computer/controller and that the most current
firmware is loaded into the receiver. Check the TPS
website for the latest updates.
If connecting via Bluetooth, check that the receiver port
used for connection is in Command mode. 65

Troubleshooting
Then, try the following:

Reset the receiver (Performing Hardware Reset on
page 49).
Restore default settings (Restoring Default Settings
on page 49).
Clear the NVRAM (Clearing the NVRAM on
page 50).
Initialize the file system (Initializing File System on
page 51). This will erase all files inside the receiver.
If the problem persists, see the following sections for other
solutions.
TX RX LED Blink Pattern on Error

Conditions
For internal FH915+/UHF modems: the TX RX LED flashes
red.
A fault condition has been detected.
Check that the radio modems antenna is
undamaged.
Contact a dealer to replace the antenna.
Check that the radio modems antenna is securely
and properly connected to the antenna connector.
Move the antenna/receiver away from conducting
66 objects (such as, large metal objects).

TX RX LED Blink Pattern on Error Conditions
The cable is damaged.

Use an undamaged cable.
Contact a Dealer to replace the cable.
For internal GSM/GPRS modems: the TX RX LED flashes
orange.
The Rover uses the wrong PIN code, or no PIN code
was selected.
1. In TopSURV, click JobConfigSurvey.
2. Click the ... (continue) button and press Next to
navigate to the Rover Radio configuration screen.
3. Press Configure GSM.
4. Select the PIN of the Base Station and press OK.
An initialization error has occurred.
Check that the radio modems antenna is
undamaged.
Check that the radio modems antenna is securely
and properly connected to the antenna connector on
the radome.
Contact a Topcon dealer to replace the antenna.
67

Troubleshooting
Obtaining Technical Support

End-users
The U.S., Canada, and international TPS equipment
users are encouraged to contact your local Topcon
dealer.
Your dealer is the focal point of contact for all post-
sales technical questions and issues.
Dealers (in the U.S., Canada, Australia)

Topcon dealers can contact Topcon Technical Support
via the password-protected Help Desk, phone, and
email.
Help Desk
To contact Topcon Technical Support via the Help
Desk, visit TechnicalSupport.Topcon.com/User.
Phone
To contact Topcon Technical Support by phone,
call:
866-4Topcon or 1-866-486-7266
68

Obtaining Technical Support
Email
To contact Topcon Technical Support via email,
use the following electronic mail address:
support@topconsokkia.com
Dealers (International)
Visit http://www.topcon.co.jp/en/positioning/network/
for contact details in your region.
Dealers in Europe must contact Topcon Technical
Support via http://support.topcon-positioning.eu/.
69

Troubleshooting
Notes:
70

GR5 - Quick Start Guide

Uploaded by

Copyright:

Available Formats

GR5 - Quick Start Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GR5 - Quick Start Guide

Uploaded by

Copyright:

Available Formats

P O S I T I O N I N G S Y S T E M S

Part Number 7010-1022

Copyright Topcon Positioning Systems, Inc.

All contents in this manual are copyrighted by

This quick start guide tells you how to

Getting Started ........................................21

P/N 7010-1022 www.topconpositioning.com

Attaching the Batteries ..................................25

Topcon GR-5 Quick Reference Guide

Downloading Files ..................................45

P/N 7010-1022 www.topconpositioning.com

Obtaining Technical Support ...............................68

Topcon GR-5 Quick Reference Guide

P/N 7010-1022 www.topconpositioning.com

Where to Find More Information

Topcon GR-5 Quick Start Guide

Getting to Know Your GR-5

The battery LEDs display the power status for each

The STAT LED displays the status of tracked satellites.

P/N 7010-1022 www.topconpositioning.com

Green blink receiver is on and tracking satellites; one

The REC LED displays the data recording status.

Topcon GR-5 Quick Start Guide

The RX TX LED displays the status of the modem.

P/N 7010-1022 www.topconpositioning.com

The BT LED indicates the level of activity at the Bluetooth

The power button turns the receiver on and off.

The FUNCTION button switches the receiver between

Topcon GR-5 Quick Start Guide

Table 1-2. FUNCTION Button Operations and REC LED Status

When data recording is off, and the FUNCTION key is...

No light No data recording.

Orange Internal file system test in progress.

Red No free memory; hardware problem with

If FUNCTION key mode is LED blink mode switch

Orange Release to change information mode.

If FUNCTION key mode is LED blink mode switch

Green Release to start data recording (post-

Green Release to start recording (Kinematic or

P/N 7010-1022 www.topconpositioning.com

Table 1-2. FUNCTION Button Operations and REC LED Status

Pressed for Red Release to turn serial port A baud rate to

Pressed for No light No function.

When data recording is on, and the FUNCTION key is...

Red No free memory; hardware problem with

If FUNCTION key mode is LED blink mode switch

Green Data recording started (post-processing

Green Data recording started (Kinematic post-

Orange Data recording started (Static post-

Topcon GR-5 Quick Start Guide

Table 1-2. FUNCTION Button Operations and REC LED Status

If FUNCTION key mode is LED blink mode switch

Orange Release to change information mode.

Orange Release to toggle between Static and

Pressed for No light Release to stop data recording.

Pressed for Red Release to turn serial port A baud rate to

Pressed for No light No function (data recording still on).

Data and Power Ports

P/N 7010-1022 www.topconpositioning.com