whi29346_ch02_064-137.

qxd 10/14/09 22:15 Page 110 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

110 Chapter 2 Pressure Distribution in a Fluid

σyy P2.6 Any pressure reading can be expressed as a length or

σyx head, h  p/g. What is standard sea-level pressure
= expressed in (a) ft of glycerin, (b) inHg, (c) m of water,
σxy
and (d) mm of ethanol? Assume all fluids are at 20
C.
A

σxx σxx Hydrostatic pressure; barometers

A
30° P2.7 La Paz, Bolivia is at an altitude of approximately
σxy 12,000 ft. Assume a standard atmosphere. How high
would the liquid rise in a methanol barometer, assumed
=
σyx at 20°C?
σyy
Hint: Don’t forget the vapor pressure.
P2.1
P2.8 A diamond mine is two miles below sea level. (a) Esti-
mate the air pressure at this depth. (b) If a barometer,
P2.2 For the two-dimensional stress field shown in Fig. P2.1 accurate to 1 mm of mercury, is carried into this mine,
suppose that how accurately can it estimate the depth of the mine? List
your assumptions carefully.
xx  2000 lbf/ft2 yy  3000 lbf/ft2 n(AA)  2500 lbf/ft2 P2.9 A storage tank, 26 ft in diameter and 36 ft high, is
lfi led with SAE 30W oil at 20°C. ( a) What is the gage
Compute (a) the shear stress xy and (b) the shear stress pressure, in lbf/in2, at the bottom of the tank? (b) How does
on plane AA. your result in (a) change if the tank diameter is reduced to
P2.3 A vertical, clean, glass piezometer tube has an inside 15 ft? (c) Repeat (a) if leakage has caused a layer of 5 ft
diameter of 1 mm. When pressure is applied, water at of water to rest at the bottom of the (full) tank.
20
C rises into the tube to a height of 25 cm. After cor- P2.10 A closed tank contains 1.5 m of SAE 30 oil, 1 m of water,
recting for surface tension, estimate the applied pressure 20 cm of mercury, and an air space on top, all at 20
C.
in Pa. The absolute pressure at the bottom of the tank is 60 kPa.
P2.4 Pressure gages, such as the Bourdon gage in Fig. P2.4, What is the pressure in the air space?
are calibrated with a deadweight piston. If the Bourdon P2.11 In Fig. P2.11, pressure gage A reads 1.5 kPa (gage).
gage is designed to rotate the pointer 10 degrees for every The fluids are at 20
C. Determine the elevations z, in
2 psig of internal pressure, how many degrees does the meters, of the liquid levels in the open piezometer tubes
pointer rotate if the piston and weight together total 44 B and C.
newtons?

θ? Bourdon
W gage B C

2m Air

2 cm
Oil
diameter
1.5 m Gasoline
P2.4
1m Glycerin
P2.5 Denver, Colorado, has an average altitude of 5300 ft. P2.11 z=0
On a standard day (Table A.6), pressure gage A in a
laboratory experiment reads 83 kPa and gage B reads P2.12 In Fig. P2.12 the tank contains water and immiscible
105 kPa. Express these readings in gage pressure or oil at 20
C. What is h in cm if the density of the oil is
vacuum pressure (Pa), whichever is appropriate. 898 kg/m3?
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 111 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 111

15 lbf/in2 abs

A
h 6 cm
Air 2 ft

12 cm Oil
1 ft
Oil B
Water
8 cm 1 ft
P2.12
P2.13 In Fig. P2.13 the 20
C water and gasoline surfaces are Water 2 ft
open to the atmosphere and at the same elevation. What
C
is the height h of the third liquid in the right leg?
P2.15

P2.16 If the absolute pressure at the interface between water and

mercury in Fig. P2.16 is 93 kPa, what, in lbf/ft2, is (a) the
pressure at the surface and (b) the pressure at the bottom
Gasoline
of the container?
1.5 m Water

h
Water 28 cm
1m
Liquid, SG = 1.60

75° 75°
P2.13

P2.14 For the three-liquid system shown, compute h1 and h2. Mercury 8 cm
Neglect the air density.

32 cm
Water
Oil, P2.16
SG =
0.78 P2.17 The system in Fig. P2.17 is at 20
C. If the pressure at
Mercury h2 point A is 1900 lbf/ft2, determine the pressures at points
B, C, and D in lbf/ft2.
27 cm
C
Air Air
8 cm 2 ft
5 cm 3 ft B
h1
A Air

P2.14 4 ft

P2.15 The air–oil–water system in Fig. P2.15 is at 20

C. Know- 5 ft
ing that gage A reads 15 lbf/in2 absolute and gage B reads
1.25 lbf/in2 less than gage C, compute (a) the specific
Water 2 ft
weight of the oil in lbf/ft3 and (b) the actual reading of D
gage C in lbf/in2 absolute. P2.17
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 112 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

112 Chapter 2 Pressure Distribution in a Fluid

P2.18 The system in Fig. P2.18 is at 20

C. If atmospheric
pressure is 101.33 kPa and the pressure at the bottom 2000
of the tank is 242 kPa, what is the specific gravity of lbf
3-in diameter
fluid X?

1 in 15 in F

1m 1-in diameter
SAE 30 oil
Oil
Water 2m

P2.20

Fluid X 3m
Air: 180 kPa abs

Mercury 0.5 m
h? Water
P2.18

P2.19 The U-tube in Fig. P2.19 has a 1-cm ID and contains mer-
cury as shown. If 20 cm3 of water is poured into the right- 80 cm Mercury
hand leg, what will the free-surface height in each leg be
after the sloshing has died down? A B
P2.21

P2.22 The fuel gage for a gasoline tank in a car reads propor-
tional to the bottom gage pressure as in Fig. P2.22. If
the tank is 30 cm deep and accidentally contains 2 cm
of water plus gasoline, how many centimeters of air
Mercury remain at the top when the gage erroneously reads
“full”?
10 cm 10 cm
Vent

Air h?
P2.19 10 cm
30 cm Gasoline
SG = 0.68

P2.20 The hydraulic jack in Fig. P2.20 is filled with oil at Water 2 cm
56 lbf/ft3. Neglecting the weight of the two pistons, what
pgage
force F on the handle is required to support the 2000-lbf P2.22
weight for this design?
P2.21 At 20
C gage A reads 350 kPa absolute. What is the P2.23 In Fig. P2.23 both fluids are at 20
C. If surface tension
height h of the water in cm? What should gage B read in effects are negligible, what is the density of the oil, in
kPa absolute? See Fig. P2.21. kg/m3?
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 113 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 113

the pressure at points 1 and 2 in Fig. P2.27b. Note that

Oil the glass is now inverted, so the original top rim of the
glass is at the bottom of the picture, and the original
bottom of the glass is at the top of the picture. The
8 cm weight of the card can be neglected. (c) Estimate the
6 cm
theoretical maximum glass height at which this experi-
ment could still work, such that the water would not fall
out of the glass.
Water
10 cm
Card Top of glass

P2.23

The atmosphere
P2.24 In Prob. 1.2 we made a crude integration of the density
distribution (z) in Table A.6 and estimated the mass of
the earth’s atmosphere to be m  6 E18 kg. Can this
result be used to estimate sea-level pressure on the earth? P2.27a Bottom of glass
Conversely, can the actual sea-level pressure of 101.35
kPa be used to make a more accurate estimate of the Original bottom of glass
atmospheric mass?
*P2.25 As measured by NASA’s Viking landers, the atmosphere of
1●
Mars, where g ≈ 3.71 m/s2, is almost entirely carbon diox-
ide, and the surface pressure averages 700 Pa. The tem-
perature is cold and drops off exponentially: T ≈ To eCz,
2●
where C  1.3E-5 m1 and To = 250 K. For example, at
20,000 m altitude, T ≈ 193 K. (a) Find an analytic formula
for the variation of pressure with altitude. (b) Find the alti- P2.27b Card Original top of glass
tude where pressure on Mars has dropped to 1 pascal.
P2.26 For gases that undergo large changes in height, the linear
P2.28 A correlation of numerical calculations indicates that,
approximation, Eq. (2.14), is inaccurate. Expand the tro-
all other things being equal, the distance traveled by a
posphere power-law, Eq. (2.20), into a power series, and
well-hit baseball varies inversely as the cube root of the
show that the linear approximation p  pa  a gz is ade-
air density. If a home-run ball hit in New York City
quate when
travels 400 ft, estimate the distance it would travel in
2T0 g (a) Denver, Colorado, and (b) La Paz, Bolivia.
z  where n  P2.29 An airplane flies at a Mach number of 0.82 at a standard
(n  1)B RB
altitude of 24,000 ft. (a) What is the plane’s velocity, in
P2.27 Conduct an experiment to illustrate atmospheric pressure. mi/h? (b) What is the standard density at that altitude?
Note: Do this over a sink or you may get wet! Find a
drinking glass with a very smooth, uniform rim at the top.
Fill the glass nearly full with water. Place a smooth, light, Manometers; multiple u
fl ids
flat plate on top of the glass such that the entire rim of P2.30 For the traditional equal-level manometer measurement in
the glass is covered. A glossy postcard works best. A small Fig. E2.3, water at 20°C ofl ws through the plug device from
index card or one flap of a greeting card will also work. a to b. The manometer fluid is mercury. If L  12 cm and
See Fig. P2.27a. h  24 cm, (a) what is the pressure drop through the
(a) Hold the card against the rim of the glass and turn device? (b) If the water flows through the pipe at a
the glass upside down. Slowly release pressure on the velocity V  18 ft/s, what is the dimensionless loss
card. Does the water fall out of the glass? Record your coefficient of the device, defined by K  Δp/(V2)? We
experimental observations. (b) Find an expression for will study loss coefficients in Chap. 6.
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 114 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

114 Chapter 2 Pressure Distribution in a Fluid

P2.31 In Fig. P2.31 all fluids are at 20

C. Determine the pres- *P2.34 Sometimes manometer dimensions have a significant
sure difference (Pa) between points A and B. effect. In Fig. P2.34 containers (a) and (b) are cylindri-
cal and conditions are such that pa  pb. Derive a for-
Kerosene mula for the pressure difference pa  pb when the
oil–water interface on the right rises a distance h h,
Benzene Air for (a) d  D and (b) d  0.15D. What is the percent-
B age change in the value of p?
A 40 cm 9 cm
20 cm D D
14 cm
8 cm (b)
Mercury Water
(a) SAE 30 oil
P2.31 H
Water
L
P2.32 For the inverted manometer of Fig. P2.32, all fluids are
at 20
C. If pB  pA  97 kPa, what must the height H be
in cm?

Meriam h
red oil,
SG = 0.827
18 cm
d
Water
H
Mercury P2.34
A
P2.35 Water flows upward in a pipe slanted at 30
, as in Fig.
P2.35. The mercury manometer reads h  12 cm. Both
35 cm fluids are at 20
C. What is the pressure difference p1  p2
in the pipe?

B
P2.32
(2)
2
P2.33 In Fig. P2.33 the pressure at point A is 25 lbf/in . All flu- 30

ids are at 20
C. What is the air pressure in the closed (1)
chamber B, in Pa?
h
Air B

SAE 30 oil

Liquid, SG = 1.45 5 cm P2.35 2m

3 cm
P2.36 In Fig. P2.36 both the tank and the tube are open to the
atmosphere. If L  2.13 m, what is the angle of tilt  of the
4 cm 6 cm
A tube?
Water P2.37 The inclined manometer in Fig. P2.37 contains Meriam red
8 cm
manometer oil, SG  0.827. Assume that the reservoir is
3 cm
very large. If the inclined arm is fitted with graduations 1
in apart, what should the angle  be if each graduation
P2.33 corresponds to 1 lbf/ft2 gage pressure for pA?
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 115 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 115

Air 8 cm

Oil 8 cm
50 cm
SG = 0.8 L
12 cm
Water Oil,
50 cm SG = 1.0 SG = 0.8
␪ 9 cm

P2.36 11 cm

P2.39 Mercury

1 in

pA D=
5
in
θ 16
A B
water air

Reservoir
P2.37
Mercury
P2.38 If the pressure in container A in Fig. P2.38 is 150 kPa,
compute the pressure in container B. P2.40 15°

B P2.41 The system in Fig. P2.41 is at 20

C. Compute the pres-
sure at point A in lbf/ft2 absolute.
Water
18 cm
Water

A
Oil,
Oil, SG = 0.85
SG = 0.8 pa = 14.7 lbf/in2
16 cm 5 in
A
22 cm 10 in
Mercury 6 in

8 cm Water

P2.38
Mercury
P2.39 In Fig. P2.39 the right leg of the manometer is open to
the atmosphere. Find the gage pressure, in Pa, in the air P2.41
gap in the tank.
P2.40 In Fig. P2.40 the pressures at A and B are the same, P2.42 Very small pressure differences pA  pB can be meas-
100 kPa. If water is introduced at A to increase pA ured accurately by the two-fluid differential manometer
to 130 kPa, find and sketch the new positions of the in Fig. P2.42. Density 2 is only slightly larger than that
mercury menisci. The connecting tube is a uniform of the upper fluid 1. Derive an expression for the
1-cm diameter. Assume no change in the liquid proportionality between h and pA  pB if the reservoirs
densities. are very large.
whi29346_ch02_064-137.qxd 10/14/09 22:15 Page 116 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

116 Chapter 2 Pressure Distribution in a Fluid

pA pB P2.45 In Fig. P2.45, determine the gage pressure at point A in

Pa. Is it higher or lower than atmospheric?
ρ1 ρ1
patm
Air
h1 h1

h
Oil,
SG = 0.85
ρ
2
30 cm
P2.42
45 cm
40 cm
P2.43 The traditional method of measuring blood pressure uses
a sphygmomanometer, first recording the highest (sys-
tolic) and then the lowest (diastolic) pressure from which 15 cm
flowing “Korotkoff” sounds can be heard. Patients with
dangerous hypertension can exhibit systolic pressures
A
as high as 5 lbf/in2. Normal levels, however, are 2.7 and
1.7 lbf/in2, respectively, for systolic and diastolic pres- P2.45 Water Mercury
sures. The manometer uses mercury and air as fluids.
(a) How high in cm should the manometer tube be? P2.46 In Fig. P2.46 both ends of the manometer are open to the
(b) Express normal systolic and diastolic blood pressure atmosphere. Estimate the specific gravity of fluid X.
in millimeters of mercury.
P2.44 Water flows downward in a pipe at 45
, as shown in
Fig. P2.44. The pressure drop p1  p2 is partly due to
gravity and partly due to friction. The mercury
manometer reads a 6-in height difference. What is the
SAE 30 oil
total pressure drop p1  p2 in lbf/in2? What is the pres- 9 cm
10 cm
sure drop due to friction only between 1 and 2 in
lbf/in2? Does the manometer reading correspond only
to friction drop? Why?
Water
5 cm

7 cm

1
45° 6 cm
5 ft Fluid X
4 cm

Flow
P2.46 12 cm
2
Water
P2.47 The cylindrical tank in Fig. P2.47 is being filled with
EES water at 20
C by a pump developing an exit pressure of
6 in 175 kPa. At the instant shown, the air pressure is 110 kPa
and H  35 cm. The pump stops when it can no longer
Mercury raise the water pressure. For isothermal air compression,
P2.44 estimate H at that time.
whi29346_ch02_064-137.qxd 10/15/09 18:22 Page 117 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 117

50 cm

Newspaper

Air
20° C
75 cm

Ruler

H Desk
Water
Pump
P2.47

P2.48 The system in Fig. P2.48 is open to 1 atm on the right P2.49
side. (a) If L  120 cm, what is the air pressure in con-
P2.50 A small submarine, with a hatch door 30 in in diameter,
tainer A? (b) Conversely, if pA  135 kPa, what is the
is submerged in seawater. (a) If the water hydrostatic
length L?
force on the hatch is 69,000 lbf, how deep is the sub?
(b) If the sub is 350 ft deep, what is the hydrostatic force
Air on the hatch?
P2.51 Gate AB in Fig. P2.51 is 1.2 m long and 0.8 m into
A the paper. Neglecting atmospheric pressure, compute
the force F on the gate and its center-of-pressure
position X.

32 cm 6m
L
18 cm 35°
15 cm
Oil,
SG = 0.82
4m
Mercury Water

P2.48 8m
A 1.2 m
Forces on plane surfaces 1m
X B
P2.49 Conduct the following experiment to illustrate air pres-
F
sure. Find a thin wooden ruler (approximately 1 ft in
40°
length) or a thin wooden paint stirrer. Place it on the edge
of a desk or table with a little less than half of it hanging P2.51
over the edge lengthwise. Get two full-size sheets of
newspaper; open them up and place them on top of the P2.52 Example 2.5 calculated the force on plate AB and its line
ruler, covering only the portion of the ruler resting on the of action, using the moment-of-inertia approach. Some
desk as illustrated in Fig. P2.49. (a) Estimate the total teachers say it is more instructive to calculate these by
force on top of the newspaper due to air pressure in the direct integration of the pressure forces. Using Figs.
room. (b) Careful! To avoid potential injury, make sure P2.52 and E2.5a, (a) find an expression for the pressure
nobody is standing directly in front of the desk. Perform variation p() along the plate; (b) integrate this expres-
a karate chop on the portion of the ruler sticking out over sion to find the total force F; (c) integrate the moments
the edge of the desk. Record your results. (c) Explain your about point A to find the position of the center of
results. pressure.
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 118 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

118 Chapter 2 Pressure Distribution in a Fluid

pa

p() A

Water
6 ft pa

8 ft
h
P2.52 B
A

P2.53 Panel ABC in the slanted side of a water tank is an isosce- 4 ft

les triangle with the vertex at A and the base BC  2 m,
B
as in Fig. P2.53. Find the water force on the panel and its
P2.55
line of action.

A
Water

4m
3m
Water
C

P2.53 B, C 3m
3m
P2.54 In Fig. P2.54, the hydrostatic force F is the same on the
bottom of all three containers, even though the weights of B
liquid above are quite different. The three bottom shapes P2.57 4m
and the fluids are the same. This is called the hydrostatic
paradox. Explain why it is true and sketch a free body of P2.58 In Fig. P2.58, the cover gate AB closes a circular open-
each of the liquid columns. ing 80 cm in diameter. The gate is held closed by a 200-kg
mass as shown. Assume standard gravity at 20
C. At what
water level h will the gate be dislodged? Neglect the
weight of the gate.

F F F 200 kg
h
P2.54 (a) (b) (c) m

P2.55 Gate AB in Fig. P2.55 is 5 ft wide into the paper, hinged B A 30 cm

at A, and restrained by a stop at B. The water is at 20
C.
Compute (a) the force on stop B and (b) the reactions at Water 3m
A if the water depth h  9.5 ft.
P2.56 In Fig. P2.55, gate AB is 5 ft wide into the paper, and stop P2.58
B will break if the water force on it equals 9200 lbf. For
what water depth h is this condition reached? *P2.59 Gate AB has length L and width b into the paper, is
P2.57 The tank in Fig. P2.57 is 2 m wide into the paper. hinged at B, and has negligible weight. The liquid level
Neglecting atmospheric pressure, find the resultant hydro- h remains at the top of the gate for any angle . Find an
static force on panel BC (a) from a single formula and analytic expression for the force P, perpendicular
(b) by computing horizontal and vertical forces separately, to AB, required to keep the gate in equilibrium in
in the spirit of Section 2.6. Fig. P2.59.
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 119 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 119

P
Pulley
A
A
10,000 lb

h L
Water
15 ft
h
Hinge ␪
P2.59 B 60° B
P2.62
P2.60 Determine the water hydrostatic force on one side of the
vertical equilateral triangle panel BCD in Fig. P2.60. P2.63 The tank in Fig. P2.63 has a 4-cm-diameter plug at the
Neglect atmospheric pressure. bottom on the right. All fluids are at 20
C. The plug will
pop out if the hydrostatic force on it is 25 N. For this con-
dition, what will be the reading h on the mercury
manometer on the left side?
20 cm
B C

Water
40 cm 50°

D
H
30 cm
P2.60

*P2.61 Gate AB in Fig. P2.61 is a homogeneous mass of 180 kg, h

1.2 m wide into the paper, hinged at A, and resting on a
smooth bottom at B. All fluids are at 20
C. For what water 2 cm
Plug,
depth h will the force at point B be zero? D = 4 cm

Mercury
P2.63
*P2.64 Gate ABC in Fig. P2.64 has a fixed hinge line at B and is
Water 2 m wide into the paper. The gate will open at A to release
water if the water depth is high enough. Compute the
Glycerin depth h for which the gate will begin to open.
h C
2m
A

1m
A 20 cm B
60° h
B
P2.61 1m
Water at 20°C
P2.62 Gate AB in Fig. P2.62 is 15 ft long and 8 ft wide into the
EES paper and is hinged at B with a stop at A. The water is at
20
C. The gate is 1-in-thick steel, SG  7.85. Compute the
water level h for which the gate will start to fall. P2.64
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 120 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

120 Chapter 2 Pressure Distribution in a Fluid

*P2.65 Gate AB in Fig. P2.65 is semicircular, hinged at B, and

held by a horizontal force P at A. What force P is required
for equilibrium?

Oil, SG = 0.83 3m 1m

A
Gate

5m
2m
Water
A
P 50° B
P
3m Gate:
Side view P2.68
B
P2.65 P2.69 Consider the slanted plate AB of length L in Fig. P2.69.
(a) Is the hydrostatic force F on the plate equal to the
weight of the missing water above the plate? If not, cor-
P2.66 Dam ABC in Fig. P2.66 is 30 m wide into the paper and rect this hypothesis. Neglect the atmosphere. (b) Can a
made of concrete (SG  2.4). Find the hydrostatic force “missing water” theory be generalized to curved surfaces
on surface AB and its moment about C. Assuming no of this type?
seepage of water under the dam, could this force tip the A
dam over? How does your argument change if there is
seepage under the dam? ␪
B

A F
Water specific weight γ

P2.69
Water 20°C
80 m P2.70 The swing-check valve in Fig. P2.70 covers a 22.86-cm
Dam diameter opening in the slanted wall. The hinge is 15 cm
from the centerline, as shown. The valve will open when
the hinge moment is 50 N  m. Find the value of h for
B the water to cause this condition.
C
P2.66 60 m
Air

*P2.67 Generalize Prob. P2.66 as follows. Denote length AB as

H, length BC as L, and angle ABC as . Let the dam 15 cm h
Hinge
material have specific gravity SG. The width of the dam
is b. Assume no seepage of water under the dam. Find
Water at 20
C
an analytic relation between SG and the critical angle c
for which the dam will just tip over to the right. Use 60

P2.70
your relation to compute c for the special case SG 
2.4 (concrete). *P2.71 In Fig. P2.71 gate AB is 3 m wide into the paper and is
P2.68 Isosceles triangle gate AB in Fig. P2.68 is hinged at A and connected by a rod and pulley to a concrete sphere
weighs 1500 N. What horizontal force P is required at (SG  2.40). What diameter of the sphere is just suffi-
point B for equilibrium? cient to keep the gate closed?
whi29346_ch02_064-137.qxd 10/16/09 16:44 Page 121 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 121

Concrete
sphere, SG = 2.4
6m
H

2R

8m P2.74
A
Oil,
SG = 0.8
4m Water
B
B
1m
Water h
P2.71
2m
P2.72 Gate B in Fig. P2.72 is 30 cm high, 60 cm wide into the P2.75
paper, and hinged at the top. What water depth h will first
cause the gate to open? P2.76 Panel BC in Fig. P2.76 is circular. Compute (a) the hydro-
static force of the water on the panel, (b) its center of pres-
sure, and (c) the moment of this force about point B.

50°

Water h 3m
Air at B
Water
10 kPa at 20°C
gage B
3m
P2.72 C

P2.73 Gate AB is 5 ft wide into the paper and opens to let fresh
water out when the ocean tide is dropping. The hinge at 3m
A is 2 ft above the freshwater level. At what ocean level
h will the gate first open? Neglect the gate weight. P2.76

A P2.77 The circular gate ABC in Fig. P2.77 has a 1-m radius and
is hinged at B. Compute the force P just sufficient to keep
Tide
the gate from opening when h  8 m. Neglect atmos-
range
pheric pressure.
pa
10 ft
h
Seawater, SG = 1.025 Water
pa
Stop B
h
P2.73
A
P2.74 Find the height H in Fig. P2.74 for which the hydrostatic 1m
force on the rectangular panel is the same as the force on
B
the semicircular panel below.
1m
P2.75 The cap at point B on the 5-cm-diameter tube in Fig.
P2.75 will be dislodged when the hydrostatic force on its C P
base reaches 22 lbf. For what water depth h does this
occur? P2.77
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 122 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

122 Chapter 2 Pressure Distribution in a Fluid

P2.78 Panels AB and CD in Fig. P2.78 are each 120 cm wide Forces on curved surfaces
into the paper. (a) Can you deduce, by inspection, which
P2.81 For the semicircular cylinder CDE in Example 2.9, find
panel has the larger water force? (b) Even if your deduc-
the vertical hydrostatic force by integrating the vertical
tion is brilliant, calculate the panel forces anyway.
component of pressure around the surface from   0 to
  .
*P2.82 The dam in Fig. P2.82 is a quarter circle 50 m wide
Water 30 cm into the paper. Determine the horizontal and vertical com-
40 cm
ponents of the hydrostatic force against the dam and the
D point CP where the resultant strikes the dam.
A

40 cm 50 cm 20 m
pa = 0
40° B C 50°

20 m
P2.78 CP
Water
P2.79 Gate ABC in Fig. P2.79 is 1 m square and is hinged at P2.82
B. It will open automatically when the water level h
becomes high enough. Determine the lowest height for *P2.83 Gate AB in Fig. P2.83 is a quarter circle 10 ft wide into
which the gate will open. Neglect atmospheric pressure. the paper and hinged at B. Find the force F just sufficient
Is this result independent of the liquid density? to keep the gate from opening. The gate is uniform and
weighs 3000 lbf.

F
h Water
A

A 60 cm Water
r = 8 ft
B
C 40 cm
B
P2.83
P2.79
P2.84 Panel AB in Fig. P2.84 is a parabola with its maximum
*P2.80 A concrete dam (SG  2.5) is made in the shape of an at point A. It is 150 cm wide into the paper. Neglect atmos-
isosceles triangle, as in Fig. P2.80. Analyze this geome- pheric pressure. Find (a) the vertical and (b) the horizon-
try to find the range of angles  for which the hydrostatic tal water forces on the panel.
force will tend to tip the dam over at point B. The width
into the paper is b.
Water
25 cm
A
Parabola

75 cm

h
P2.84 40 cm B

P2.85 Compute the horizontal and vertical components of the

hydrostatic force on the quarter-circle panel at the bottom
P2.80 ␪ ␪ B of the water tank in Fig. P2.85.
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 126 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

126 Chapter 2 Pressure Distribution in a Fluid

P2.104 The can in Fig. P2.104 floats in the position shown. What
is its weight in N?
D
SG = 1.0

h
3 cm

Fluid, SG > 1
8 cm Water W

P2.109
P2.104 D = 9 cm
P2.110 A solid sphere, of diameter 18 cm, floats in 20
C water
P2.105 It is said that Archimedes discovered the buoyancy laws with 1,527 cubic centimeters exposed above the surface.
when asked by King Hiero of Syracuse to determine (a) What are the weight and specific gravity of this
whether his new crown was pure gold (SG  19.3). sphere? (b) Will it float in 20
C gasoline? If so, how many
Archimedes measured the weight of the crown in air to cubic centimeters will be exposed?
be 11.8 N and its weight in water to be 10.9 N. Was it P2.111 A hot-air balloon must be designed to support basket,
pure gold? cords, and one person for a total weight of 1300 N. The
P2.106 A spherical helium balloon is 2.5 m in diameter and has balloon material has a mass of 60 g/m2. Ambient air is
a total mass of 6.7 kg. When released into the U.S. stan- at 25
C and 1 atm. The hot air inside the balloon is at
dard atmosphere, at what altitude will it settle? 70
C and 1 atm. What diameter spherical balloon will
P2.107 Repeat Prob. 2.62, assuming that the 10,000-lbf weight is just support the total weight? Neglect the size of the hot-
aluminum (SG  2.71) and is hanging submerged in the air inlet vent.
water. P2.112 The uniform 5-m-long round wooden rod in Fig. P2.112
P2.108 A 7-cm-diameter solid aluminum ball (SG  2.7) and a is tied to the bottom by a string. Determine (a) the ten-
solid brass ball (SG  8.5) balance nicely when sub- sion in the string and (b) the specific gravity of the wood.
merged in a liquid, as in Fig. P2.108. (a) If the fluid is Is it possible for the given information to determine the
water at 20
C, what is the diameter of the brass ball? inclination angle ? Explain.
(b) If the brass ball has a diameter of 3.8 cm, what is the
density of the fluid?
1m

2 pulleys D = 8 cm

  ␪
Water at 20°C

4m
Aluminum Brass
D = 7 cm String
P2.108

P2.109 A hydrometer floats at a level that is a measure of the spe-

cific gravity of the liquid. The stem is of constant diam- P2.112
eter D, and a weight in the bottom stabilizes the body to
float vertically, as shown in Fig. P2.109. If the position P2.113 A spar buoy is a buoyant rod weighted to float and pro-
h  0 is pure water (SG  1.0), derive a formula for h trude vertically, as in Fig. P2.113. It can be used for meas-
as a function of total weight W, D, SG, and the specific urements or markers. Suppose that the buoy is maple wood
weight 0 of water. (SG  0.6), 2 in by 2 in by 12 ft, floating in seawater
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 127 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 127

(SG  1.025). How many pounds of steel (SG  7.85) P2.116 The deep submersible vehicle ALVIN in the chapter-
should be added to the bottom end so that h  18 in? opener photo has a hollow titanium (SG = 4.50) spheri-
cal passenger compartment with an inside diameter of
78.08 in and a wall thickness of 1.93 in. (a) Would the
h empty sphere float in seawater? (b) Would it float if it
contained 1000 lbm of people and equipment inside?
(c) What wall thickness would cause the empty sphere to
be neutrally buoyant?
P2.117 The balloon in Fig. P2.117 is filled with helium and pres-
surized to 135 kPa and 20
C. The balloon material has a
mass of 85 g/m2. Estimate (a) the tension in the mooring
Wsteel line and (b) the height in the standard atmosphere to
which the balloon will rise if the mooring line is cut.
P2.113

P2.114 The uniform rod in Fig. P2.114 is hinged at point B on

the waterline and is in static equilibrium as shown when
2 kg of lead (SG  11.4) are attached to its end. What is D = 10 m
the specific gravity of the rod material? What is peculiar
about the rest angle   30
?
Air:
100 kPa at
Hinge
20°C
D = 4 cm
P2.117
B
␪ = 30

P2.118 An intrepid treasure-salvage group has discovered a steel

box, containing gold doubloons and other valuables, rest-
8m ing in 80 ft of seawater. They estimate the weight of the
box and treasure (in air) at 7000 lbf. Their plan is to attach
2 kg of lead
the box to a sturdy balloon, inflated with air to 3 atm pres-
sure. The empty balloon weighs 250 lbf. The box is 2 ft
wide, 5 ft long, and 18 in high. What is the proper diam-
P2.114
eter of the balloon to ensure an upward lift force on the
P2.115 The 2-in by 2-in by 12-ft spar buoy from Fig. P2.113 has box that is 20 percent more than required?
5 lbm of steel attached and has gone aground on a rock, P2.119 When a 5-lbf weight is placed on the end of the uniform
as in Fig. P2.115. Compute the angle  at which the buoy floating wooden beam in Fig. P2.119, the beam tilts at an
will lean, assuming that the rock exerts no moments on angle  with its upper right corner at the surface, as
the spar. shown. Determine (a) the angle  and (b) the specific
gravity of the wood. Hint: Both the vertical forces and the
moments about the beam centroid must be balanced.

5 lbf
θ
Wood
8 ft θ SG = 0.6
9 ft
Water
4 in × 4 in

Seawater
P2.119
A
P2.120 A uniform wooden beam (SG  0.65) is 10 cm by 10 cm
Rock by 3 m and is hinged at A, as in Fig. P2.120. At what angle
P2.115  will the beam float in the 20
C water?
128 Chapter 2 Pressure Distribution in a Fluid

A 2.5 m
60
H 60

1m 8m
P2.123
θ

Water
P2.124 A balloon weighing 3.5 lbf is 6 ft in diameter. It is filled
with hydrogen at 18 lbf/in2 absolute and 60
F and is
P2.120 released. At what altitude in the U.S. standard atmosphere
will this balloon be neutrally buoyant?
P2.121 The uniform beam in Fig. P2.121, of size L by h by b and P2.125 A solid sphere, of diameter 20 cm, has a specific gravity
with specific weight b, floats exactly on its diagonal when of 0.7. (a) Will this sphere float in 20
C SAE 10W oil?
a heavy uniform sphere is tied to the left corner, as If so, (b) how many cubic centimeters are exposed, and
(c) how high will a spherical cap protrude above the sur-
face? Note: If your knowledge of offbeat sphere formulas
Width b << L
is lacking, you can “Ask Dr. Math” at Drexel University,
L h << L <http://mathforum.org/dr.math/> EES is recommended
γb for the solution.
P2.126 A block of wood (SG  0.6) floats in fluid X in
γ Fig. P2.126 such that 75 percent of its volume is sub-
merged in fluid X. Estimate the vacuum pressure of the
Diameter D
air in the tank.
SG > 1
Air = 0 kPa gage Air pressure?

P2.121 Wood
40 cm
shown. Show that this can happen only (a) when b  /3
and (b) when the sphere has size
1/3 70 cm Fluid X
Lhb
D c d
(SG  1)
P2.126
P2.122 A uniform block of steel (SG  7.85) will “float” at a
mercury–water interface as in Fig. P2.122. What is the Stability of ofl ating bodies
ratio of the distances a and b for this condition?
*P2.127 Consider a cylinder of specific gravity S 1 floating ver-
tically in water (S  1), as in Fig. P2.127. Derive a for-
mula for the stable values of D/L as a function of S and
apply it to the case D/L  1.2.
Water
Steel a
D
block b

Mercury: SG = 13.56
P2.122
L
h
P2.123 A barge has the trapezoidal shape shown in Fig. P2.123
and is 22 m long into the paper. If the total weight of
barge and cargo is 350 tons, what is the draft H of the
barge when floating in seawater? P2.127
whi29346_ch02_064-137.qxd 10/14/09 22:16 Page 129 Debd 208:MHDQ176:whi29346:0073529346:whi29346_pagefiles:

Problems 129

P2.128 An iceberg can be idealized as a cube of side length L, as positions shown in Fig. P2.134. Which is the more
in Fig. P2.128. If seawater is denoted by S  1.0, then stable position? Assume large width into the paper.
glacier ice (which forms icebergs) has S  0.88. Deter-
mine if this “cubic” iceberg is stable for the position
shown in Fig. P2.128.

Specific gravity
=S (a) (b)
P2.134
M? P2.135 Consider a homogeneous right circular cylinder of
G
h Water length L, radius R, and specific gravity SG, floating in
B
S = 1.0 water (SG  1). Show that the body will be stable with
its axis vertical if
L R
P2.128  32SG(1  SG) 4 1/2
L
P2.136 Consider a homogeneous right circular cylinder of length
P2.129 The iceberg idealization in Prob. P2.128 may become L, radius R, and specific gravity SG  0.5, floating in
unstable if its sides melt and its height exceeds its width. water (SG  1). Show that the body will be stable with
In Fig. P2.128 suppose that the height is L and the depth its axis horizontal if L /R  2.0.
into the paper is L, but the width in the plane of the paper
is H L. Assuming S  0.88 for the iceberg, find the Uniform acceleration
ratio H/L for which it becomes neutrally stable (about to
P2.137 A tank of water 4 m deep receives a constant upward
overturn).
acceleration az. Determine (a) the gage pressure at the tank
P2.130 Consider a wooden cylinder (SG  0.6) 1 m in diameter
bottom if az  5 m2/s and (b) the value of az that causes
and 0.8 m long. Would this cylinder be stable if placed to
the gage pressure at the tank bottom to be 1 atm.
float with its axis vertical in oil (SG  0.8)?
P2.138 A 12-fl-oz glass, of 3-in diameter, partly full of water, is
P2.131 A barge is 15 ft wide and 40 ft long and floats with a draft
attached to the edge of an 8-ft-diameter merry-
of 4 ft. It is piled so high with gravel that its center of
go-round, which is rotated at 12 r/min. How full can the
gravity is 3 ft above the waterline. Is it stable?
glass be before water spills? Hint: Assume that the glass is
P2.132 A solid right circular cone has SG  0.99 and floats
much smaller than the radius of the merry-go-round.
vertically as in Fig. P2.132. Is this a stable position for
P2.139 The tank of liquid in Fig. P2.139 accelerates to the right
the cone?
with the fluid in rigid-body motion. (a) Compute ax in
m/s2. (b) Why doesn’t the solution to part (a) depend on
the density of the fluid? (c) Determine the gage pressure
at point A if the fluid is glycerin at 20
C.
Water :
SG = 1.0
ax
SG = 0.99
28 cm
P2.132
15 cm
100 cm
A
P2.133 Consider a uniform right circular cone of specific grav-
ity S 1, floating with its vertex down in water (S  1). P2.139
The base radius is R and the cone height is H. Calcu-
late and plot the stability MG of this cone, in dimen- P2.140 Suppose an elliptical-end fuel tank that is 10 m long and
sionless form, versus H/R for a range of S 1. has a 3-m horizontal major axis and 2-m vertical major
P2.134 When floating in water (SG  1.0), an equilateral tri- axis is filled completely with fuel oil (  890 kg/m3). Let
angular body (SG  0.9) might take one of the two the tank be pulled along a horizontal road. For rigid-body