Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 45 views

    Lead Screw Replacement Instructions

    Uploaded by

    123anthony
    Lead Screw Replacement Instructions

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Lead Screw Replacement Instructions

    Uploaded by

    123anthony
    45 views2 pages
    Lead Screw Replacement Instructions

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Lead Screw Replacement Instructions

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    45 views2 pages

    Lead Screw Replacement Instructions

    Uploaded by

    123anthony
    Lead Screw Replacement Instructions

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    w w w. i n c r a .

    c o m

    Lead Screw Replacement Instructions (Carriage)


    Tools required:
    Small Crescent Wrench, Phillips Screwdriver, 1/8 hex key, 5/32 hex key, x-acto knife or scratch awl.
    RETAIN BLACK
    1. Remove fence from end of the LS Carriage the un- 6. Pull on the Red WASHER
    clamp and slide the Micro Adjust Knob to
    Carriage out of the snap the Lead Screw
    base. Assembly out of the
    carriage. Again, keep
    2. Use a 5/32 hex key to unscrew the set screw the carriage horizontal
    through the access hole in the when removing the
    fence mounting bracket and lead screw in order to
    remove the spring and ball retain the 5/16 diam-
    bearing. You may need to tip eter ball bearing located inside of the black spacer
    the carriage forward to allow at the forward end of the lead screw. If necessary,
    the ball bearing to roll out. use a screwdriver between the between the carriage
    Retain the set screw, spring and the red knob to GENTLY leverage the lead screw
    and ball bearing for re-assem- assembly up and out of the carriage. Slide the large
    bly. black washer located next to the black micro adjust
    disc off and add it to the new Lead Screw Assembly.
    3. Remove locking
    nut and set screw 7. Before installing the
    along with all (5) new Lead Screw As-
    Phillips head screws sembly, make sure that
    from end plate the 5/16 diameter ball
    located at rear end bearing is still inside the
    of carriage. Remove 1/4 long black spacer
    end plate. Keep located just behind
    carriage horizontal the fence mounting
    when removing end plate to avoid losing the ball bracket.
    bearing located inside of the black spacer at the rear
    end of the lead screw. 8. Carefully lower the
    new Lead Screw As-
    4. Slide the 3/8 long sembly into the carriage
    black spacer with starting at the forward
    5/16 diameter ball (fence mounting brack-
    bearing located at et) end and snap the
    the end of the lead assembly into position.
    screw out of the car-
    riage. 9. Slide the (2) long
    black plastic rods into
    the extruded cavities
    5. Use an x-acto knife or a on either side of the
    scratch awl to slide the (2) lead screw.
    long black plastic rods located
    on either side of the lead
    screw out of the carriage.

    page 1

    Manufactured by: Taylor Design Group, Inc. P.O. BOX 810262 Dallas, TX 75381 w w w.incra.com
    w w w. i n c r a . c o m

    Lead Screw Replacement Instructions (Carriage)

    10. Slide the 3/8 long 13. Replace the ball


    black spacer with the bearing, followed by
    5/16 diameter ball the spring and the
    bearing inside into the set screw through
    carriage at the rear end the hole located in
    of the lead screw. the front of the fence
    mounting bracket.
    Thread the set screw in until it is just below the face of
    the fence mounting bracket. DO NOT TIGHTEN THIS
    11. Re-attach the carriage end plate using the (5) Phil- SET SCREW.
    lips head screws. TO AVOID STRIPPING THE THREADS,
    DO NOT USE A POWER DRIVER DURING ASSEMBLY. 14. If converting to the Metric Lead Screw Assembly,
    remove all existing scales on the top of the carriage
    and replace with (1)
    430mm
    Lexan scale and (1)
    TO AVOID STRIPPING Stainless Steel scale.
    THE THREADS, DO
    NOT USE A POWER
    DRIVER DURING
    RE-ASSEMBLY.

    12. Hand thread the set screw into the end plate.
    This set screw is used to remove end to end play in
    the Lead Screw Assembly. ROTATE THIS SET SCREW
    WITH YOUR FINGERS ONLY until end to end play is
    removed. You can test for end play by pushing and
    pulling on the Red Micro Adjust Knob. Once the end
    play is removed, use a 1/8 hex key to hold the set
    screw in place as you thread on and tighten the lock-
    ing nut. DO NOT USE THE HEX KEY TO TIGHTEN THE
    SET SCREW. EXCESSIVE PRESSURE ON THE END OF THE
    LEAD SCREW WILL NOT PERMIT EASY ROTATION AND
    MAY DAMAGE THE FENCE MOUNTING BRACKET! After
    tightening the locking nut, check for end play and
    fine-tune as necessary.

    page 2

    Photography: Grahame Waterson INCRA is a Registered Trademark of Taylor Design Group


    MADE IN THE
    Manufactured by: 2010 Taylor Design Group, Inc.
    Taylor Design Group, Inc. INCRA Tools are protected by one or more of the following US patents:
    USA
    P.O. BOX 810262 Dallas, TX 75381 #4,793,604, #4,930,221, #5,195,730, #5,275,074, #5,423,360, #5,716,045, #6,237,457,
    w w w.incra.com #6,557,601, #6,672,190. Other patents granted or pending. rev.03.10.2010

    You might also like