Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Turbine

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 9
At a glance
Powered by AI
The document discusses the basic principles and components of gas turbines, as well as some of their common uses in power generation and other industrial applications.

Gas turbines work by compressing air, mixing it with fuel and igniting it to produce hot exhaust gases that spin a turbine and drive a generator to produce electricity.

The main components of a gas turbine are the compressor, combustion chamber, and turbine. The compressor increases the pressure and temperature of incoming air before it is mixed with fuel and burned in the combustion chamber. The hot exhaust gases then expand through the turbine to produce rotation.

Turbine

sGas Turbine for Power Generation:


Introduction
The use of gas turbines for generating electricity dates back to 1939. Today, gas turbines are one
of the most widely-used power generating technologies. Gas turbines are a type of internal
combustion (IC) engine in which burning of an air-fuel mixture produces hot gases that spin a
turbine to produce power. It is the production of hot gas during fuel combustion, not the fuel
itself that the gives gas turbines the name. Gas turbines can utilize a variety of fuels, including
natural gas, fuel oils, and synthetic fuels. Combustion occurs continuously in gas turbines, as
opposed to reciprocating IC engines, in which combustion occurs intermittently.

How Do Gas Turbines Work?


Gas turbines are comprised of three primary sections mounted on the same shaft: the compressor,
the combustion chamber (or combustor) and the turbine. The compressor can be either axial flow
or centrifugal flow. Axial flow compressors are more common in power generation because they
have higher flow rates and efficiencies. Axial flow compressors are comprised of multiple stages
of rotating and stationary blades (or stators) through which air is drawn in parallel to the axis of
rotation and incrementally compressed as it passes through each stage. The acceleration of the air
through the rotating blades and diffusion by the stators increases the pressure and reduces the
volume of the air. Although no heat is added, the compression of the air also causes the
temperature to increase.

The compressed air is mixed with fuel injected through nozzles. The fuel and compressed air can
be pre-mixed or the compressed air can be introduced directly into the combustor. The fuel-air

1
Turbine

mixture ignites under constant pressure conditions and the hot combustion products (gases) are
directed through the turbine where it expands rapidly and imparts rotation to the shaft. The
turbine is also comprised of stages, each with a row of stationary blades (or nozzles) to direct the
expanding gases followed by a row of moving blades. The rotation of the shaft drives the
compressor to draw in and compress more air to sustain continuous combustion. The remaining
shaft power is used to drive a generator which produces electricity. Approximately 55 to 65
percent of the power produced by the turbine is used to drive the compressor. To optimize the
transfer of kinetic energy from the combustion gases to shaft rotation, gas turbines can have
multiple compressor and turbine stages.

Alstom GT24/GT26 Gas Turbine (Image credit: Alstom)

Because the compressor must reach a certain speed before the combustion process is continuous
or self-sustaining initial momentum is imparted to the turbine rotor from an external motor,
static frequency converter, or the generator itself. The compressor must be smoothly accelerated
and reach firing speed before fuel can be introduced and ignition can occur. Turbine speeds vary
widely by manufacturer and design, ranging from 2,000 revolutions per minute (rpm) to 10,000
rpm. Initial ignition occurs from one or more spark plugs (depending on combustor design).
Once the turbine reaches self-sustaining speed above 50% of full speed the power output is
enough to drive the compressor, combustion is continuous, and the starter system can be
disengaged.

Gas Turbine Performance


The thermodynamic process used in gas turbines is the Brayton cycle. Two significant
performance parameters are the pressure ratio and the firing temperature. The fuel-to-power
efficiency of the engine is optimized by increasing the difference (or ratio) between the
compressor discharge pressure and inlet air pressure. This compression ratio is dependent on the
design. Gas turbines for power generation can be either industrial (heavy frame) or
aeroderivative designs. Industrial gas turbines are designed for stationary applications and have
lower pressure ratios typically up to 18:1. Aeroderivative gas turbines are lighter weight

2
Turbine

compact engines adapted from aircraft jet engine design which operate at higher compression
ratios up to 30:1. They offer higher fuel efficiency and lower emissions, but are smaller and
have higher initial (capital) costs. Aeroderivative gas turbines are more sensitive to the
compressor inlet temperature.

The temperature at which the turbine operates (firing temperature) also impacts efficiency, with
higher temperatures leading to higher efficiency. However, turbine inlet temperature is limited
by the thermal conditions that can be tolerated by the turbine blade metal alloy. Gas temperatures
at the turbine inlet can be 1200C to 1400C, but some manufacturers have boosted inlet
temperatures as high as 1600C by engineering blade coatings and cooling systems to protect
metallurgical components from thermal damage.

Because of the power required to drive the compressor, energy conversion efficiency for a
simple cycle gas turbine power plant is typically about 30 percent, with even the most efficient
designs limited to 40 percent. A large amount of heat remains in the exhaust gas, which is around
600C as it leaves the turbine. By recovering that waste heat to produce more useful work in a
combined cycle configuration, gas turbine power plant efficiency can reach 55 to 60 percent.
However, there are operational limitations associated with operating gas turbines in combined
cycle mode, including longer startup time, purge requirements to prevent fires or explosions, and
ramp rate to full load.

Advantages of gas turbine engines


Very high power-to-weight ratio, compared to reciprocating engines;
Smaller than most reciprocating engines of the same power rating.
Moves in one direction only, with far less vibration than a reciprocating engine.
Fewer moving parts than reciprocating engines.
Greater reliability, particularly in applications where sustained high power output is required
Waste heat is dissipated almost entirely in the exhaust. This results in a high temperature
exhaust stream that is very usable for boiling water in a combined cycle, or for cogeneration.
Low operating pressures.
High operation speeds.
Low lubricating oil cost and consumption.
Can run on a wide variety of fuels.
Very low toxic emissions of CO and HC due to excess air, complete combustion and no "quench"
of the flame on cold surfaces

Disadvantages of gas turbine engines


Cost is very high
Less efficient than reciprocating engines at idle speed
Longer startup than reciprocating engines
Less responsive to changes in power demand compared with reciprocating engines
Characteristic whine can be hard to suppress

3
Turbine

Theory of operation

In an ideal gas turbine, gases undergo three thermodynamic processes: an isentropic


compression, an isobaric (constant pressure) combustion and an isentropic expansion. Together,
these make up the Brayton cycle.

In a practical gas turbine, mechanical energy is irreversibly transformed into heat when gases are
compressed (in either a centrifugal or axial compressor), due to internal friction and turbulence.
Passage through the combustion chamber, where heat is added and the specific volume of the
gases increases, is accompanied by a slight loss in pressure. During expansion amidst the stator
and rotor blades of the turbine, irreversible energy transformation once again occurs.

If the device has been designed to power a shaft as with an industrial generator or a turboprop,
the exit pressure will be as close to the entry pressure as possible. In practice it is necessary that
some pressure remains at the outlet in order to fully expel the exhaust gases. In the case of a jet
engine only enough pressure and energy is extracted from the flow to drive the compressor and
other components. The remaining high pressure gases are accelerated to provide a jet that can,
for example, be used to propel an aircraft.

Brayton cycle

As with all cyclic heat engines, higher combustion temperatures can allow for greater
efficiencies. However, temperatures are limited by ability of the steel, nickel, ceramic, or other
materials that make up the engine to withstand high temperatures and stresses. To combat this
many turbines feature complex blade cooling systems.

As a general rule, the smaller the engine, the higher the rotation rate of the shaft(s) must be to
maintain tip speed. Blade-tip speed determines the maximum pressure ratios that can be obtained
by the turbine and the compressor. This, in turn, limits the maximum power and efficiency that
can be obtained by the engine. In order for tip speed to remain constant, if the diameter of a rotor
is reduced by half, the rotational speed must double. For example, large jet engines operate
around 10,000 rpm, while micro turbines spin as fast as 500,000 rpm.[10]

Mechanically, gas turbines can be considerably less complex than internal combustion piston
engines. Simple turbines might have one moving part: the shaft/compressor/turbine/alternative-
rotor assembly (see image above), not counting the fuel system. However, the required precision
manufacturing for components and temperature resistant alloys necessary for high efficiency
often make the construction of a simple turbine more complicated than piston engines.

4
Turbine

More sophisticated turbines (such as those found in modern jet engines) may have multiple
shafts (spools), hundreds of turbine blades, movable stator blades, and a vast system of complex
piping, combustors and heat exchangers.

Thrust bearings and journal bearings are a critical part of design. Traditionally, they have been
hydrodynamic oil bearings, or oil-cooled ball bearings. These bearings are being surpassed by
foil bearings, which have been successfully used in micro turbines an

Advances in technology
Gas turbine technology has steadily advanced since its inception and continues to evolve.
Development is actively producing both smaller gas turbines and more powerful and efficient
engines. Aiding in these advances are computer based design (specifically CFD and finite
element analysis) and the development of advanced materials: Base materials with superior high
temperature strength (e.g., single-crystal superalloys that exhibit yield strength anomaly) or
thermal barrier coatings that protect the structural material from ever higher temperatures. These
advances allow higher compression ratios and turbine inlet temperatures, more efficient
combustion and better cooling of engine parts.

Computational Fluid Dynamics (CFD) has contributed to substantial improvements in the


performance and efficiency of Gas Turbine engine components through enhanced understanding
of the complex viscous flow and heat transfer phenomena involved. For this reason, CFD is one
of the key computational tool used in Design & development of gas [50]turbine engines.

The simple-cycle efficiencies of early gas turbines were practically doubled by incorporating
inter-cooling, regeneration (or recuperation), and reheating. These improvements, of course,
come at the expense of increased initial and operation costs, and they cannot be justified unless
the decrease in fuel costs offsets the increase in other costs. The relatively low fuel prices, the
general desire in the industry to minimize installation costs, and the tremendous increase in the
simple-cycle efficiency to about 40 percent left little desire for opting for these modifications.[51]

On the emissions side, the challenge is to increase turbine inlet temperatures while at the same
time reducing peak flame temperature in order to achieve lower NOx emissions and meet the
latest emission regulations. In May 2011, Mitsubishi Heavy Industries achieved a turbine inlet
temperature of 1,600 C on a 320 megawatt gas turbine, and 460 MW in gas turbine combined-
cycle power generation applications in which gross thermal efficiency exceeds 60%.[52]

Compliant foil bearings were commercially introduced to gas turbines in the 1990s. These can
withstand over a hundred thousand start/stop cycles and have eliminated the need for an oil
system. The application of microelectronics and power switching technology have enabled the
development of commercially viable electricity generation by micro turbines for distribution and
vehicle propulsion.

5
Turbine

Types of gas turbines


Jet engines

A typical axial-flow gas turbine turbojet, the J85, sectioned for display. Flow is left to right, multistage
compressor on left, combustion chambers center, two-stage turbine on right.

Airbreathing jet engines are gas turbines optimized to produce thrust from the exhaust gases, or
from ducted fans connected to the gas turbines. Jet engines that produce thrust from the direct
impulse of exhaust gases are often called turbojets, whereas those that generate thrust with the
addition of a ducted fan are often called turbofans or (rarely) fan-jets.

Gas turbines are also used in many liquid propellant rockets, the gas turbines are used to power a
turbopump to permit the use of lightweight, low pressure tanks, which saves considerable dry
mass.

Turboprop engines

A turboprop engine is a type of turbine engine which drives an external aircraft propeller using a
reduction gear. Turboprop engines are generally used on small subsonic aircraft, but some large
military and civil aircraft, such as the Airbus A400M, Lockheed L-188 Electra and Tupolev Tu-
95, have also used turboprop power.

Aeroderivative gas turbines

Diagram of a high-pressure turbine blade

Aeroderivatives are also used in electrical power generation due to their ability to be shut down,
and handle load changes more quickly than industrial machines. They are also used in the marine

6
Turbine

industry to reduce weight. The General Electric LM2500, General Electric LM6000, Rolls-
Royce RB211 and Rolls-Royce Avon are common models of this type of machine.[citation needed]

Amateur gas turbines

Increasing numbers of gas turbines are being used or even constructed by amateurs.

In its most straightforward form, these are commercial turbines acquired through military surplus
or scrapyard sales, then operated for display as part of the hobby of engine collecting.[11][12] In its
most extreme form, amateurs have even rebuilt engines beyond professional repair and then used
them to compete for the Land Speed Record.

The simplest form of self-constructed gas turbine employs an automotive turbocharger as the
core component. A combustion chamber is fabricated and plumbed between the compressor and
turbine sections.[13]

More sophisticated turbojets are also built, where their thrust and light weight are sufficient to
power large model aircraft.[14] The Schreckling design[14] constructs the entire engine from raw
materials, including the fabrication of a centrifugal compressor wheel from plywood, epoxy and
wrapped carbon fibre strands.

Several small companies now manufacture small turbines and parts for the amateur. Most
turbojet-powered model aircraft are now using these commercial and semi-commercial
microturbines, rather than a Schreckling-like home-build.[15]

Auxiliary power units

APUs are small gas turbines designed to supply auxiliary power to larger, mobile, machines such
as an aircraft. They supply:

compressed air for air conditioning and ventilation,


compressed air start-up power for larger jet engines,
mechanical (shaft) power to a gearbox to drive shafted accessories or to start large jet engines,
and
electrical, hydraulic and other power-transmission sources to consuming devices remote from
the APU.

7
Turbine

Industrial gas turbines for power generation

GE H series power generation gas turbine: in combined cycle configuration, this 480-megawatt unit has
a rated thermal efficiency of 60%.

Industrial gas turbines differ from aeronautical designs in that the frames, bearings, and blading
are of heavier construction. They are also much more closely integrated with the devices they
power often an electric generatorand the secondary-energy equipment that is used to recover
residual energy (largely heat).

They range in size from man-portable mobile plants to enormous, complex systems weighing
more than a hundred tonnes housed in block-sized buildings. When the turbine is used solely for
shaft power, its thermal efficiency is around the 30% mark. This may cause a problem in which
it is cheaper to buy electricity than to burn fuel. Therefore many engines are used in CHP
(Combined Heat and Power) configurations that can be small enough to be integrated into
portable container configurations.

Gas turbines can be particularly efficientup to at least 60%when waste heat from the turbine
is recovered by a heat recovery steam generator to power a conventional steam turbine in a
combined cycle configuration.[16][17] They can also be run in a cogeneration configuration: the
exhaust is used for space or water heating, or drives an absorption chiller for cooling the inlet air
and increase the power output, technology known as Turbine Inlet Air Cooling.

Another significant advantage is their ability to be turned on and off within minutes, supplying
power during peak, or unscheduled, demand. Since single cycle (gas turbine only) power plants
are less efficient than combined cycle plants, they are usually used as peaking power plants,
which operate anywhere from several hours per day to a few dozen hours per yeardepending
on the electricity demand and the generating capacity of the region. In areas with a shortage of
base-load and load following power plant capacity or with low fuel costs, a gas turbine power
plant may regularly operate most hours of the day. A large single-cycle gas turbine typically
produces 100 to 400 megawatts of electric power and has 3540% thermal efficiency.[18]

Industrial gas turbines for mechanical drive

Industrial gas turbines that are used solely for mechanical drive or used in collaboration with a
recovery steam generator differ from power generating sets in that they are often smaller and
feature a dual shaft design as opposed to single shaft. The power range varies from 1 megawatt

8
Turbine

up to 50 megawatts.[citation needed] These engines are connected directly or via a gearbox to either a
pump or compressor assembly. The majority of installations are used within the oil and gas
industries. Mechanical drive applications increase efficiency by around 2%.

Oil and Gas platforms require these engines to drive compressors to inject gas into the wells to
force oil up via another bore, or to compress the gas for transportation. They're also often used to
provide power for the platform. These platforms don't need to use the engine in collaboration
with a CHP system due to getting the gas at an extremely reduced cost (often free from burn off
gas). The same companies use pump sets to drive the fluids to land and across pipelines in
various intervals.

You might also like