JUNE 2017: AMIETE - ET (Current & New Scheme)

ROLL NO.
___________________
Code: AE72/AE120 Subject: MICROWAVE THEORY AND TECHNIQUES

AMIETE ET (Current & New Scheme)
Time: 3 Hours JUNE 2017 Max. Marks: 100
PLEASE WRITE YOUR ROLL NO. AT THE SPACE PROVIDED ON EACH PAGE
IMMEDIATELY AFTER RECEIVING THE QUESTION PAPER.
NOTE: There are 9 Questions in all.
Question 1 is compulsory and carries 20 marks. Answer to Q.1 must be written in
the space provided for it in the answer book supplied and nowhere else.
The answer sheet for the Q.1 will be collected by the invigilator after 45 Minutes of
the commencement of the examination.
Out of the remaining EIGHT Questions, answer any FIVE Questions. Each
question carries 16 marks.
Any required data not explicitly given, may be suitably assumed and stated.
Q.1 Choose the correct or the best alternative in the following: (2 10)
a. In Cavity Magnetron, strapping is used to

(A) Prevent mode jumping
(B) Prevent cathode back heating
(C) Ensure bunching
(D) Improve the phase focussing effect
b. The Cross Field Amplifier (CFA) is a

(A) Linear Amplifier (B) Parametric Amplifier
(C) Non linear Amplifier (D) Saturated Amplifier
c. A transmission line is called a flat line when its Standing Wave Ratio (SWR) is
(A) 0 (B) 1
(C) infinity (D) minimum
d. Which of these is not a type of Lithography technology?

(A) Electron beam Lithography (B) Conducting beam Lithography
(C) Ion beam Lithography (D) X-ray Lithography
e. The standing wave ratio of a pure travelling wave is

(A) Unity (B) Infinite
(C) /2 (D)
AE72/AE120/June -2017 1
ROLL NO. ___________________
h. Which one of the following modes has the characteristic of attenuation becoming
less as the frequency is increased and is attractive at microwave frequencies for
circular cylindrical waveguides?
(A) TE 11 mode (B) TM 01 mode
(C) TE 01 mode (D) higher order mode
i. The path length between ports 1 and 2 for the two waves in a hybrid ring is:
(A) 1 (B) 3/4
(C) /2 (D) /4
Answer any FIVE Questions out of EIGHT Questions.

Each question carries 16 marks.
Q.2 a. Draw the profile of SWR versus reflection coefficient. A transmission line has a
characteristic impedance of 50 + j 0.01 and is terminated in a load line
impedance of 73-j42.5 .
Calculate: (i) The reflection coefficient (ii) the standing wave ratio. (8)
b. Write the characteristics of smith chart and describe the steps involved in
determination of normalized impedance using smith chart. (8)
Q.3 a. An air filled rectangular waveguide has dimensions of a = 6 cm and b = 4 cm.

The signal frequency is 3 GHz. Compute the following for the TE 10 mode; (8)
(i) Cut off frequency (ii) Wavelength in the waveguide
(iii) Phase velocity (iv) Group velocity
b. Starting from Maxwells equations, derive wave equation for rectangular wave
guide. (8)
Q.4 a. Explain the Waveguide Corners, Bends and Twists in waveguide components.
(8)
AE72/AE120/June -2017 2
ROLL NO. ___________________

b. A signal of power 32 mW is fed into one of the collinear ports of a lossless H-
Plane Tee. Determine the powers in the remaining ports when other ports are
terminated by means of matched loads. (8)
Q.5 a. An n-type GaAs Gunn diode has the following parameters: (6)
v d = 2.5 x 105 m/s; | n | = 0.015 m2/V.s; r =13.1
Determine the criterion for classifying the modes of operation.
b. Explain the principle of operation of a tunnel diode. Draw its I-V characteristics.
(10)
Q.6 a. A Reflex klystron operates under the following conditions:

V O = 600 volts, = 1mm, R sh = 15 K, e = 1.759 1011 , f r = 9 GHz
m
3
The tube is operating at f v f r at the peak of the n = 2 mode or 1 mode. The
4
transit time through the gap and beam loading can be neglected. Find the value
of repeller voltage V r . (8)
b. Write the schematic diagram of two cavity klystron amplifier and explain the
velocity modulation process. (8)
Q.7 a. Explain the principle of operation Forward Wave Cross-Field Amplifier. (8)
(8)
Q.8 a. Derive expression for Quality Factor Q of Micro-Strip Lines and show that it is
approximately the reciprocal of the dielectric loss tangent . (10)
b. Explain ohmic losses in microstrip lines. (6)
Q.9 a. List the various techniques by which monolithic microwave integrated circuits
can be fabricated. Explain lithography. (10)
b. Describe a thin film planar resistor and express the resistance in terms of its
parameters. (6)
AE72/AE120/June -2017 3

JUNE 2017: AMIETE - ET (Current & New Scheme)

Uploaded by

Copyright:

Available Formats

JUNE 2017: AMIETE - ET (Current & New Scheme)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

JUNE 2017: AMIETE - ET (Current & New Scheme)

Uploaded by

Copyright:

Available Formats

ROLL NO.

Code: AE72/AE120 Subject: MICROWAVE THEORY AND TECHNIQUES

Time: 3 Hours JUNE 2017 Max. Marks: 100

a. In Cavity Magnetron, strapping is used to

b. The Cross Field Amplifier (CFA) is a

d. Which of these is not a type of Lithography technology?

e. The standing wave ratio of a pure travelling wave is

Code: AE72/AE120 Subject: MICROWAVE THEORY AND TECHNIQUES

Answer any FIVE Questions out of EIGHT Questions.

Q.3 a. An air filled rectangular waveguide has dimensions of a = 6 cm and b = 4 cm.

Code: AE72/AE120 Subject: MICROWAVE THEORY AND TECHNIQUES

Q.6 a. A Reflex klystron operates under the following conditions:

b. Explain ohmic losses in microstrip lines. (6)

You might also like