AIRLESS TIPS

Tips on tips

www.graco.be

CHOOSING THE RIGHT TIP FOR YOUR JOB IS ESSENTIAL

The spray tip affects a job’s profit margin as much as any other piece of equipment on the site.

• Optimize your performance

• Improve your work quality
• Control your costs

All Airless Applications

AIRLESS TIPS
HOW DO TIPS WORK?
• An airless sprayer pumps and pressur-
The pump produces:
izes the paint without the use of air. • Paint flow
• Paint pressure
• The paint is then forced to go through
the small orifice of the tip under high
pressure (up to 350 bar).
• This process atomizes the paint in a
controlled fan width and flow rate
(same effect as placing your thumb on The tip defines:
the end of a garden hose) • The spraying angle
• The spraying volume

The tip size tells the pump how hard it must work in
order to maintain the desired pressure.

WHY SO MANY DIFFERENT TIPS AND SIZES?

You can compare it to choosing the right
bit for your electric drill.
There are bits designed for wood, bits for
metal and bits for concrete.
Each bit for each application comes in a
variety of sizes.
Using the wrong bit on the wrong
surface does not work.
With airless tips it is very similar.

CHOOSING THE RIGHT TIP

• decreases overspray
• provides more control
• results in less time to spend
on the job
• less paint usage
• and higher profits

HOW TO CHOOSE THE RIGHT TIP?

Getting the most from your spray tip depends on several factors:

• THE TIP’S FAN WIDTH

• THE TIP’S ORIFICE SIZE
• YOUR SPRAYER’S MAXIMUM OUTPUT
• THE TYPE OF PAINT YOU ARE SPRAYING
• THE TYPE OF SURFACE YOU ARE SPRAYING
• TIP WEAR
 THE FAN WIDTH
of a tip is defined by it’s spray angle when
spraying at 30 cm distance from the
surface.The angle is indicated with one
number only:
• 5 in this case
corresponds to
an angle of 50°.
To obtain the fan width, multiply the num-
ber of the angle by 5:
• 5 x 5 = 25 cm fan width

WIDE RAC®
The wider the spray pattern, the faster
the surface is painted. 30 SEC. 3 passes
Wide spraying greatly improves
productivity. with WA
However, wide spraying is difficult to con-
trol and wide spray tips are not available
in all sizes.
1 MIN. 6 passes
Graco provides a special range of RAC X™
tips, WAxxxx, specifically cut to provide a
superb result at a wide angle, saving you
time. with standard tip

THE ORIFICE SIZE

defines the amount of paint that will flow Your actual flow rate will depend on your
through the tip. spraying pressure and the paint you are
It is indicated by the last two digits: using: high pressure equals more flow;
heavier paints equal less flow.
• 17 in this case corresponds to a hole
size of 0.017 of an inch or 0.43 mm

EVERY SPRAYER HAS A MAXIMUM OUTPUT LEVEL.

It is important never to exceed the maximum spray tip size that your machine can handle.
Example: if you require 4,4 l/min the smallest sprayer recommended is the Ultra®Max II 1095.
Inches 0.007 0.009 0.011 0.013 0.015 0.017 0.019 0.021 0.023 0.025 0.027 0.029 0.031 0.033 0.035 0.037 0.039 0.041 0.043 0.045 0.047
mm 0.18 0.23 0.28 0.3302 0.38 0.43 0.48 0.53 0.58 0.64 0.69 0.74 0.79 0.84 0.89 0.94 0.99 1.04 1.09 1.14 1.19
l/min 0.2 0.3 0.5 0.7 0.9 1.2 1.5 1.8 2.2 2.5 3.0 3.4 3.9 4.4 5 5.6 6.2 6.8 7.5 8.2 9
RANGE MODEL
ST MAX™ 395
495
ST MAX™ II 595
ULTRA® MAX II 695
795
1095
MARK V with paint
with plaster
X with paint
with plaster
GMAX™ 3900
5900 HD
7900
EH 200
200
GH 230
300
GH 833
GH 5030
3640
2560
2075
ROOFING 1015
Fine Finish Applications Professional Airless Applications Heavy Duty Applications
 THE TYPE OF PAINT as well as THE SURFACE
you are spraying define the kind of tip you should use.
The table below indicates recommended tips and sizes for different applications and materials.

FINE FINISH TIPS

Typical applications Materials Recommended tip sizes Corresponding guards

RAC X™ Cabinetry, wood working, Dyes 008 - 010 RAC X™

FFAxxx metal and fine finish Ink 010 - 012 246215
surfaces Stains 012 - 014
Flat Silver Lacquers 012 - 014 Flat tip
163xxx 220251
Oils 012 - 014
Flat Black Enamels 012 - 014 Flat tip
163xxx Urethanes 012 - 014 220247
Auto finishes 008 - 014

PROFESSIONAL AIRLESS TIPS

RAC X™ Residential, commercial Latex 015 - 019 RAC X™
PAAxxx or industrial job sites. Acrylics 015 - 019 246215
Both interior and Multi colours 023 - 025
Contractor flat exterior. Emulsions 017 - 021 Flat tip
269xxx Block fillers 023 - 025 220251

Flat Silver Silicon 021 - 025 Flat tip

163xxx 220251

HEAVY DUTY TIPS

RAC X™ High production, large Block fillers 027 - 031

HDAxxx surfaces. Residential, Intumescents 029 - 035 RAC X™
WAxxxx commercial or industrial Spachtel 029 - 041 246215
job sites. Elastomerics 027 - 033
Flat Silver
Both interior and Mastics 041 - 047 Flat tip
163xxx
exterior paint as well Epoxies 043 - 061 220251
as airless plaster Fibered 047 - 053
applications. Asphalt 031 - 071
Silicat/Mineral 027 - 033
Contact cement -

AIRLESS STRIPING TIPS

RAC® 5 LineLazer Parking lots, roads, ware- Airless striping 013 - 055 RAC® 5
LL5xxx house floors, crossings paints 243161
and athletic fields.

Ideal to reduce overspray. Top quality 015 - 021

Sharp line edges. exterior paints
Even paint distribution
across the line.

FOR ALL TIP SIZES AVAILABLE IN ALL TIP RANGES, PLEASE CONTACT YOUR GRACO DISTRIBUTOR
s
ent
ers

NEW WORN
s
nes

esc
rs

ion

Fill
ls

Texture & high viscosity material for spray applications 1st digit x 5 time to
s
que

me

ylic
tha
ins

uls

um
ck
ex

= fan width* change!

Ena
Lac

Ure

Acr
Sta

Em

Blo
Lat
Ink

Int

FFA-XXX PAA-XXX HDA-XXX

108 110 112 115 5 cm 3 cm
208 210 212 214 215 217 219 221 225 227 231 235 10 cm 7 cm
308 310 312 314 315 317 319 321 325 327 331 335 15 cm 10 cm
410 412 414 415 417 419 421 323 425 427 329 431 433 435 439 441 443 445 451 455 20 cm 15 cm
510 512 514 515 517 519 521 423 525 527 429 531 533 535 537 539 541 543 545 551 555 561 665 25 cm 20 cm
612 614 615 617 619 621 523 625 627 529 631 633 635 637 639 641 643 645 651 655 661 671 30 cm 25 cm
721 623 629 735 35 cm 30 cm
819 821 723 827 729 831 833 835 40 cm 35 cm
WA-XXXX 1221 1223 1225 1227 1229 1231 1233 1235 1237 1239 60 cm 55 cm
*at 30 cm spraying distance
ADJUSTING TO THE RIGHT TIP
PROBLEM SOLUTION
Too much paint? 515 1) Reduce orifice size
517 17
15

WALL

25 cm
50°

WALL

35 cm
717 2) Increase fan angle 70°
5
7
0.017" = 1.17 lpm

Not enough paint?

519 1) Increase orifice size
517
17
19

WALL

25 cm
50°

WALL

15 cm
319 2) Decrease fan angle 30°
5
3
0.017" = 1.17 lpm

Based on this general information, you what is the optimum tip for your applica-
will be able to choose the appropriate tip tion.
for your application. Ask your distributor or your GRACO
Experiencing with a few tips will help you representative for specific tip size recom-
gain experience and will help you decide mendations.

TIPS DO WEAR AND WILL NEED REPLACEMENT

THE TWO MAIN CAUSES FOR TIP WHAT HAPPENS WHEN A TIP
WEAR ARE: WEARS?
• Working pressure at the gun.
• Abrasive material INCREASED TIP WEAR

To explain what tip wear is and what this

FAN WIDTH

means to your business, think again of the

23 cm

14 cm
28 cm
30 cm

similarities between spray tips and drill

bits. Have you ever tried to drill into con-
crete using a worn out bit? If you have,
then you know that it takes much longer 1,25 l/min
to drill, takes much more effort and the
NEW WORN
drilled hole ends up being very unprofes-
sional. It is the same with continuing to
spray with a worn out tip.
1 Fan width decreases
+ = more passes necessary = more labour
2 orifice size increases = more paint comes out
= more material cost

TOTAL: TWICE THE LABOUR!

+ 30% more paint for the same surface!

Note that by using a worn out tip you might surpass the maximum output of your sprayer.
Using a worn out tip will end up costing you much more than the cost of replacing a tip
(labour + paint).
 ABOUT GRACO
Founded in 1926, Graco is a world leader in fluid handling systems and components. Graco products
move, measure, control, dispense and apply a wide range of fluids and viscous materials used
in vehicle lubrication, commercial and industrial settings.

The company’s success is based on its unwavering commitment to technical excellence, world-class
manufacturing and unparalleled customer service. Working closely with qualified distributors, Graco
offers systems, products and technology that set the quality standard in a wide range of fluid handling
solutions. Graco provides equipment for spray finishing, protective coating, paint circulation, lubrication,
and dispensing sealants and adhesives, along with power application equipment for the contractor
industry. Graco’s ongoing investment in fluid management and control will continue to provide
innovative solutions to a diverse global market.

GRACO LOCATIONS
CONTACT AMERICAS EUROPE
MAILING ADDRESS MINNESOTA BELGIUM
P.O. Box 1441 Worldwide Headquarters European Headquarters
Minneapolis, MN 55440-1441 Graco Inc. Graco N.V.
Tel: 612.623.6000 88-11th Avenue N.E. Industrieterrein-Oude Bunders
Fax: 612.623.6777 Minneapolis, MN 55413 Slakweidestraat 31
3630 Maasmechelen,
Belgium
Tel: 32.89.770.700
Fax: 32.89.770.777

ASIA PACIFIC ASIA PACIFIC ASIA PACIFIC

JAPAN CHINA KOREA
Graco K.K. Graco Hong Kong Ltd. Graco Korea Inc.
1-27-12 Hayabuchi Representative Office Choheung Bank Building
Tsuzuki-ku Room 118 1st Floor 4th Floor #1599
Yokohama City, Japan 2240025 No.2 Xin Yuan Building Gwanyang-Dong, Dongan-Ku,
Tel: 81.45.593.7300 No.509 Cao Bao Road Anyang-Si, Gyunggi-Do,
Fax: 81.45.593.7301 Shanghai, P.R. China 200233 Korea 431-060
Tel: 86.21.649.50088 Tel: 82(Korea).31.476.9400
Fax: 86.21.649.50077 Fax: 82(Korea).31.476.9801

All written and visual data contained in this document are based on the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.

Graco is certified ISO 9001.

Europe
+32 89 770 700
FAX +32 89 770 777
WWW.GRACO.BE

©2008 Graco N.V. 300666 E Rev. B 01/08 Printed in Europe.

All other brand names or marks are used for identification purposes and are trademarks of their respective owners.