PassLeader JN0-102 Exam Dumps (301-End)

New VCE and PDF Exam Dumps from PassLeader
➢ Vendor: Juniper
➢ Exam Code: JN0-102
➢ Exam Name: Juniper Networks Certified Associate - Junos (JNCIA-Junos)
➢ Questions 301 – End
Visit PassLeader and Download Full Version JN0-102 Exam Dumps
QUESTION 301
Referring to the exhibit, what is the purpose of the targets section of the configuration?
[editsnmp]
user@router# show
communityCommunityA {
authorization read-only;
clients {
192.168.1.0/28;
}
}
trap-groupgroupA {
categories {
link;
}
targets {
192.168.100.1;
192.168.200.1;
}
}
A. It defines which devices will be sending traps.

B. It specifies where to send traps.
C. It defines the IP addresses of management systems that can access the device.
D. It specifies which devices can be polled for SNMP data.
Answer: B
QUESTION 302
Referring to the exhibit, which statement is correct?
traceroute to 10.1.15.2 (10.1.15.2), 30 hops max, 40 byte packets
1 10.1.36.1 (10.1.36.1) 0.651 ms 7.834 ms 0.506 ms
2 10.1.23.1 (10.1.23.1) 0.5 ms 0.5 ms 0.5 ms
3 * * *
4 * * *
A. The packets have exceeded the time-to-live value.

B. There is a loop.
C. The asterisks indicate a response time out.
JN0-102 Exam Dumps JN0-102 Exam Questions JN0-102 PDF Dumps JN0-102 VCE Dumps
https://www.passleader.com/jn0-102.html
D. The asterisks indicate that the traceroute is completed.
Answer: C
QUESTION 303
In the exhibit, what does the (>) symbol indicate?
user@router# run show route /24
inet.0: 142 destinations, 142 routes (141 active, 0 holddown, 1 hidden)
+ = Active Route, - = Last Active, * = Both
/24 *[OSPF/10] 04:10:20
>to 172.25.213.11 via ge-1/0/1.0
to 172.25.213.23 via ge-1/0/2.0
A. There is a software issue with ge-1/0/1.0 interface.

B. There is a hardware issue with ge-1/0/1.0 interface.
C. The next hop of 172.25.213.11 is selected.
D. The next hop of 172.25.213.11 is not resolvable.
Answer: C
QUESTION 304
You have been asked to establish reachability between Router 1's and Router 2's loopback
addresses as shown in the exhibit.
Which two steps will accomplish this task? (Choose two.)
A. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.2.

B. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.1.
C. Create a static route on Router 2 to 172.17.25.1 with a next hop of 10.10.10.1.
D. Create a static route on Router 1 to 172.17.25.1 with a next hop of 10.10.10.2.
Answer: AC
QUESTION 305
Given the configuration shown in the exhibit, which statement is correct about traffic matching the
route 10.10.10.0/24?
[edit routing-options]
user@router# show
static {
defaults {
metric 10;
preference 10;
}
route 10.10.10.0/24 {
next-hop 192.168.100.1;
qualified-next-hop 192.168.200.1;
preference 6;
}
metric 8;
}
}
A. It will be forwarded to 192.168.100.1 using a metric of 10.

B. It will be forwarded to 192.168.100.1 using a metric of 8.
C. It will be forwarded to 192.168.200.1 using a metric of 8.
D. It will be forwarded to 192.168.200.1 using a metric of 10.
Answer: C
QUESTION 306
user@router> show route
10.10.10.91/32 *[Direct/0] 00:09:40
>via lo0.0
10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1
>to 172.16.1.2 via ge-0/0/2.0
100.100.1.0/24 *[Static/5] 00:01:50
Reject
172.16.1.0/24 *[Direct/0] 00:06:09
>via ge-0/0/2.0
172.16.1.1/32 *[Local/0] 00:06:09
Local via ge-0/0/2.0
192.168.0.0/16 *[Aggregate/130] 00:00:06
Reject
192.168.0.0/17 *[Aggregate/130] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.50.0/24 *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.51.0/24 *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
user@router> show configuration policy-options
policy-statement demo {
term 1 {
from {
route-filter 192.168.0.0/16 longer accept;
}
then reject;
}
}
user@router> show configuration protocols ospf
export demo;
area 0.0.0.0 {
interface ge-0/0/2.0;
}
Given the configuration and routing table shown in the exhibit, which routes will be advertised to
OSPF neighbors because of the demo policy?
A. 192.168.0.0/16 only
B. 192.168.0.0/17 only
C. 192.168.50.0/24 and 192.168.51.0/24
D. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24
Answer: D
QUESTION 307
user@router> show route
10.10.10.91/32 *[Direct/0] 00:09:40
>via lo0.0
10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1
>to 172.16.1.2 via ge-0/0/2.0
100.100.1.0/24 *[Static/5] 00:01:50
Reject
172.16.1.0/24 *[Direct/0] 00:06:09
>via ge-0/0/2.0
172.16.1.1/32 *[Local/0] 00:06:09
192.168.0.0/16 *[Aggregate/130] 00:00:06
Reject
192.168.0.0/17 *[Aggregate/130] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.50.0/24 *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
192.168.51.0/24 *[Static/5] 00:00:06
>to 172.16.1.2 via ge-0/0/2.0
term 1 {
from {
protocol static;
route-filter 192.168.0.0/16 orlonger accept;
}
then accept;
}
}
export demo;
area 0.0.0.0 {
}
A. 192.168.0.0/16 only
B. 192.168.50.0/24 only
C. 192.168.50.0/24 and 192.168.51.0/24
D. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24
Answer: C
QUESTION 308
user@router> show configuration firewall
familyinet {
filter demo {
term example {
from {
source-address {
100.100.100.0/24;
}
destination-address {
200.200.200.0/24;
}
}
then {
reject;
}
}
term testing {
from {
source-address {
10.10.10.0/28;
}
200.200.200.0/24;
}
}
then sample;
}
term results {
from {
address {
200.200.200.0/24;
}
}
then accept;
}
term final {
thenpolicer LAPD;
}
}
}
Given the configuration shown in the exhibit, what will happen to traffic from source 10.10.10.25
destined to 200.200.200.1?
A. The traffic will be rejected.

B. The traffic will be dropped.
C. The traffic will be forwarded.
D. The traffic will be policed.
Answer: C
QUESTION 309
destinations, 9 routes (9 active, 0 holddown, 0 hidden)
10.10.10.91/32 *[Direct/0] 00:09:40
> via lo0.0
10.10.10.92/32 *[OSPF/10] 00:01:50, metric 1
> to 172.16.1.2 via ge-0/0/2.0
100.100.1.0/24 *[Static/5] 00:01:50
Reject
172.16.1.0/24 *[Direct/0] 00:06:09
> via ge-0/0/2.0
172.16.1.1/32 *[Local/0] 00:06:09
192.168.0.0/16 *[Aggregate/130] 00:00:06
Reject
192.168.0.0/17 *[Aggregate/130] 00:00:06
> to 172.16.1.2 via ge-0/0/2.0
192.168.50.0/24 *[Static/5] 00:00:06
> to 172.16.1.2 via ge-0/0/2.0
192.168.51.0/24 *[Static/5] 00:00:06
> to 172.16.1.2 via ge-0/0/2.0
term 1 {
from {
protocol aggregate;
route-filter 192.168.0.0/16 longer;
}
then accept;
}
}
export demo;
area 0.0.0.0 {
}
A. 192.168.0.0/16 only
B. 192.168.0.0/17 only
C. 192.168.0.0/16 and 192.168.0.0/17
D. 192.168.0.0/17, 192.168.50.0/24, and 192.168.51.0/24
Answer: B
QUESTION 310
Referring to the exhibit, which two statements are true? (Choose two.)
[edit policy-options]
user@router# show
policy-statement policyABC {
term A {
from {
protocol rip;
route-filter 192.168.1.0/24 longer;
}
then accept;
}
}
[edit protocols ospf]
user@router# show
export policyABC;
area 0.0.0.0 {
interface lo0.0;
A. The route 192.168.1.0/25 is accepted.

B. The route 192.168.2.0/24 is accepted.
C. OSPF routes will be exported into RIP.
D. RIP routes will be exported into OSPF.
Answer: AD
QUESTION 311
Given the configuration shown in the exhibit, what is the function of the protect-loopback filter?
[edit interfaces]
user@router# show
...
lo0 {
unit 0 {
family inet {
filter {
input protect-loopback;
}
address 192.168.100.1/32;
A. To protect the Routing Engine

B. To protect all interfaces on the device
C. To protect the Packet Forwarding Engine
D. To protect the management interface
Answer: A
QUESTION 312
Referring to the exhibit, you want to block HTTP access to Web-Server from the subnet where Mal-
User is located. All other traffic should be permitted.
……
Which firewall filter configuration do you use?
A. [edit firewall family inet filter STOP-MAL-USER]

user@router# show
term one {
from {
source-address {
200.200.200.0/24;
}
100.100.100.10/32;
}
protocol tcp;
destination-port http;
}
then accept;
}
term two {
then {
reject;
}
}
B. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
100.100.100.0/24;
}
200.200.200.1/32;
}
protocol tcp;
}
then accept;
}
term two {
then {
reject;
}
}
C. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
100.100.100.0/24;
}
200.200.200.1/32;
}
protocol tcp;
}
then reject;
}
term two {
then {
accept;
}
}
D. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
200.200.200.0/24;
}
100.100.100.10/32;
}
protocol tcp;
}
then reject;
}
term two {
then {
accept;
}
}
Answer: D
QUESTION 313
Referring to the exhibit, you want to block HTTP access to Web-Server from the subnet where Mal-
User is located. All other traffic should be permitted.
……
Which firewall filter configuration do you use?
A. [edit firewall family inet filter STOP-MAL-USER]

user@router# show
term one {
from {
source-address {
200.200.200.0/24;
}
100.100.100.10/32;
}
protocol tcp;
}
then accept;
}
term two {
then {
reject;
}
}
B. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
100.100.100.0/24;
}
200.200.200.1/32;
}
protocol tcp;
}
then accept;
}
term two {
then {
reject;
}
}
C. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
100.100.100.0/24;
}
200.200.200.1/32;
}
protocol tcp;
}
then reject;
}
term two {
then {
accept;
}
}
D. [edit firewall family inet filter STOP-MAL-USER]
user@router# show
term one {
from {
source-address {
200.200.200.0/24;
}
100.100.100.10/32;
}
protocol tcp;
}
then reject;
}
term two {
then {
accept;
}
}
Answer: D
QUESTION 314
The configuration in the exhibit is associated with which class of service component?
...
if-exceeding {
bandwidth-limit 1m;
burst-size-limit 3k;
}
then discard;
A. Classification
B. Policing
C. Queuing
D. Scheduling
Answer: B
QUESTION 315
Referring to the exhibit, which type of classifier is being used in this CoS configuration?
[edit firewall family inet filter COS-CLASSIFIER]
user@router# show
term MANAGER {
from {
source-address {
192.168.200.0/25;
}
100.100.100.1/32;
}
}
then {
forwarding-class expedited-forwarding;
accept;
}
}
term ALL-OTHER-TRAFFIC {
then accept;
}
[edit interfaces ge-0/0/1]
user@router# show
unit 0 {
family inet {
filter {
input COS-CLASSIFIER;
}
address 192.168.200.1/24;
}
}
A. behavior aggregate
B. policer
C. multifield
D. forwarding policy
Answer: C
QUESTION 316
Referring to the exhibit, which type of classifier is being used in this CoS configuration?
[edit class-of-service]
user@router# show
interfaces {
ge-0/0/2 {
unit 0 {
classifiers {
inet-precedence default;
}
}
}
}
A. behavior aggregate
B. policer
C. multifield
D. forwarding policy
Answer: A
QUESTION 317
Given the routing entries shown in the exhibit, which next-hop IP address will be used for the
destination IP address 192.168.1.142? (Assume that only static routes are available for the
destination.)
user@router> show route protocol static
192.168.1.128/27 *[Static/5] 00:03:13
> to 10.20.106.10 via fe-0/0/5.106
192.168.1.144/29 *[Static/5] 00:03:13
> to 10.20.14.131 via ge-0/0/0.0
192.168.1.192/27 *[Static/5] 00:03:13
> to 10.18.1.1 via ge-0/0/1.0
192.168.1.128/28 *[Static/5] 00:01:06
> to 10.20.14.130 via ge-0/0/0.0
A. 10.20.106.10
B. 10.20.14.131
C. 10.18.1.1
D. 10.20.14.130
Answer: D
QUESTION 318
Using the routing table shown in the exhibit, what will be the next-hop IP address used for a
destination IP address of 192.168.1.1? (Assume that the only routes to this destination are static
routes.)
192.168.1.0/24 *[Static/5] 00:03:13
> to 10.20.106.10 via fe-0/0/5.106
192.168.1.192/26 *[Static/5] 00:03:13
> to 10.20.14.131 via ge-0/0/0.0
192.168.1.192/27 *[Static/5] 00:03:13
> to 10.18.1.1 via ge-0/0/1.0
192.168.1.4/30 *[Static/5] 00:01:06
> to 10.20.14.130 via ge-0/0/0.0
A. 10.20.14.130
B. 10.18.1.1
C. 10.20.14.131
D. 10.20.106.10
Answer: D
QUESTION 319
Given the routing entries shown in the exhibit, which next-hop IP address will be used for the
destination IP address 192.168.1.159? (Assume that only static routes are available for the
destination.)
192.168.1.128/27 *[Static/5] 00:03:13
> to 10.20.106.10 via fe-0/0/5.106
192.168.1.144/29 *[Static/5] 00:03:13
> to 10.20.14.131 via ge-0/0/0.0
192.168.1.192/27 *[Static/5] 00:03:13
> to 10.18.1.1 via ge-0/0/1.0
192.168.1.128/28 *[Static/5] 00:01:06
> to 10.20.14.130 via ge-0/0/0.0
A. 10.20.14.130
B. 10.18.1.1
C. 10.20.14.131
D. 10.20.106.10
Answer: D
QUESTION 320
What are three examples of dynamic IGPs? (Choose three.)
A. OSPF
B. BGP
C. IS-IS
D. PIM
E. RIP
Answer: ACE
QUESTION 321
Which three statements are true about terms in a policy? (Choose three.)
A. The order of the terms in a policy is irrelevant.

B. The action is specified in a then statement.
C. Terms are optional in a policy.
D. The match condition can be identified with a from statement.
E. A from statement is mandatory in a term.
Answer: BCD
QUESTION 322
Which two statements are true about terms in a routing policy? (Choose two.)
A. A routing policy cannot have more than one term.

B. If a term does not contain a from statement, all routes match.
C. If a term does not contain a from statement, the Junos OS will not commit.
D. A then statement is not mandatory in a term.
Answer: BD
QUESTION 323
Which statement is true about terms in a policy?
A. A single term can be applied to a protocol or interface, independent of the policy.

B. Once configured, terms within a policy cannot be reordered.
C. The name of a term is limited to five characters.
D. A from statement is optional in a term.
Answer: D
QUESTION 324
Which command is a valid way to view the status of an interface?
A. > show interfaces fe-0/0/0 extensive

B. > show interfaces fe-0/0/0 status
C. > show interfaces fe-0/0/0 health-info
D. > show interfaces fe-0/0/0 verbose
Answer: A
Explanation:
You can get the information from "show interface <interface_name> extensive"
https://forums.juniper.net/t5/Ethernet-Switching/Any-Command-like-as-cisco-s-quotshow-
interface-status-quot/td-p/4596
QUESTION 325
Given the host IP address of 192.168.100.60 and a network mask of 255.255.255.224 (or /27),
which address represents the correct network address for the referenced host?
A. 192.168.100.48
B. 192.168.100.16
C. 192.168.100.0
D. 192.168.100.32
Answer: D
Explanation:
Network is a class C network: 192.168.100.32/27.
Binary: 11000000.10101000.01100100.00100000.
http://jodies.de/ipcalc?host=192.168.100.60&mask1=27&mask2=
QUESTION 326
Referring to the exhibit, which three networks match the policy? (Choose three.)
[edit policy-options policy-statement my-policy]
user@router# show
term 1 {
from {
route-filter 192.168.0.0/16 prefix-length-range /20-/24;
}
then accept;
}
A. 192.168.0.0/20
B. 192.168.0.0/16
C. 192.168.128.0/18
D. 192.168.128.0/21
E. 192.168.64.0/24
Answer: ADE
QUESTION 327
Referring to the exhibit, you must move the match term above the reject term.
[edit policy-options policy-statement my-policy]
user@router# show
term reject {
then reject;
}
term match {
from {
protocolbgp;
route-filter 10.10.10.0/24 exact;
}
}
Which command would accomplish this task?
A. set term match from policy reject

B. up 1 copy policy-statement my-policy term match to term before-reject
C. activate term match to policy
D. insert term match before term reject
Answer: D
QUESTION 328
Which command produces the output shown in the exhibit?
A. show firewall counter telnet-counter filter select-telnet

B. show firewall log
C. show log messages
D. show services accounting usage
Answer: B
QUESTION 329
Which two statements are true about firewall filter configurations? (Choose two.)
A. Multiple action modifiers can be included in the same term.

B. Only a single action modifier can be included in the same term.
C. The default term within a firewall filter uses the discard action.
D. The default term within a firewall filter uses the reject action.
Answer: AC
QUESTION 330
Which two statements are true about firewall filter configurations? (Choose two.)
A. Multiple action modifiers can be included in the same term.

B. Only a single action modifier can be included in the same term.
C. If an action modifier exists without a terminating action, matching packets will be accepted.
D. If an action modifier exists without a terminating action, matching packets will be discarded.
Answer: AC
QUESTION 331
You have configured a firewall filter with a single term matching on packets with a source address
in the 10.0.0.0/24 subnet. This term only includes the count action. Which two statements are true
about traffic evaluated by this firewall filter? (Choose two.)
A. Packets outside the 10.0.0.0/24 subnet will be accepted.

B. Packets outside the 10.0.0.0/24 subnet will be rejected.
C. Packets outside the 10.0.0.0/24 subnet will be counted.
D. Packets outside the 10.0.0.0/24 subnet will not be counted.
Answer: BD
QUESTION 332
The IP address 192.168.100.1 belongs to which class of IP address space?
A. Class A
B. Class B
C. Class C
D. Class D
Answer: C
QUESTION 333
Which command configures an address of 192.168.1.1 with a mask of 255.255.255.0 on interface
ge-0/0/0?
A. set ip interface ge-0/0/0 address 192.168.1.1 255.255.255.0

B. set ip interface ge-0/0/0 address 192.168.1.1/24
C. set interface ge-0/0/0 ip4 address 192.168.1.1 mask 255.255.255.0
D. set interfaces ge-0/0/0 unit 0 family inet address 192.168.1.1/24
Answer: D
Explanation:
http://www.juniper.net/documentation/en_US/junos12.3/topics/example/interfacesconfiguring-fast-
ethernet-interfaces.html
QUESTION 334
Which two protocols are connection-oriented? (Choose two.)
A. Ethernet
B. PPP
C. TCP
D. UDP
Answer: BC
Explanation:
http://searchnetworking.techtarget.com/definition/connection-oriented
QUESTION 335
Which statement is correct about the validate option when upgrading JUNOS software?
A. It will check the MD5 checksum of the install package.

B. It will check if the device meets the memory requirements for the install package.
C. It will check the compatibility of the configuration with the install package.
D. It will check if the device meets the storage requirement for the install package.
Answer: C
Explanation:
When you upgrade or downgrade Junos OS, we recommend that you include the validate option
with the request system software add command to check that the candidate software is compatible
with the current configuration. By default, when you add a package with a different release number,
the validation check is done automatically.
https://www.juniper.net/techpubs/en_US/junos12.3/topics/task/operational/junoscandidate-
software-compatibility-verifying.html
QUESTION 336
What are three advantages which dynamic routing protocols offer over static routing protocols?
(Choose three.)
A. lower administrative overhead

B. increased network availability
C. greater network scalability
D. easier to implement qualified next hops
E. easier ECMP route implementation
Answer: ABC
Explanation:
Dynamic routing protocols help the network administrator manage the time-consuming and
exacting process of configuring and maintaining static routes. Dynamic routing automatically
adapts topology to reroute traffic if possible. Dynamic routing is generally independent of the
network size.
http://www.ciscopress.com/articles/article.asp?p=2180210&seqNum=5
QUESTION 337
When troubleshooting ATM, which command would allow you to test reachability from one side of
an ATM cloud to the other?
A. ping atm vci 0.100 interface at-0/1/0 end-to-end

B. ping atm vci 0.100 interface at-0/1/0 circuit
C. ping atm vci 0.100 interface at-0/1/0 far-end
D. ping atm vci 0.100 interface at-0/1/0 final-hop
Answer: A
Explanation:
http://www.juniper.net/documentation/en_US/junos13.3/topics/reference/commandsummary/ping-
atm.html
QUESTION 338
Which command will display the temperature of the Routing Engine's CPU?
A. show chassis environment

B. show chassis routing-engine
C. show chassis temperatures
D. show chassis status
Answer: B
Explanation:
https://www.juniper.net/documentation/en_US/junos11.4/topics/reference/commandsummary/sho
w-chassis-routing-engine.html
QUESTION 339
Which commnand would correctly define a router's host-name?
A. # set ip host-name <name>

B. > set ip host-name <name>
C. # set system host-name <name>
D. > set system host-name <name>
Answer: C
Explanation:
http://www.juniper.net/techpubs/en_US/junos15.1/topics/example/router-namedomain-name-ip-
address-system-id-configuring.html
QUESTION 340
You have been asked to use a 28 bit subnet mask to segment the following network block:
108.12.5.0. How many usable hosts per sub-net could you create?
A. 10 hosts
B. 14 hosts
C. 12 hosts
D. 16 hosts
Answer: B
Explanation:
Network: 108.12.5.0/28 (Class A)
Broadcast: 108.12.5.15
HostMin: 108.12.5.1
HostMax: 108.12.5.14
Hosts/Net: 14
http://jodies.de/ipcalc?host=108.12.5.0&mask1=28&mask2=
QUESTION 341
In Ethernet networks, duplex mismatches will lower performance. Which error statistics can be
seen if a duplex mismatch is present?
A. collisions on the full-duplex side; runts on the half-duplex side

B. collisions on the full-duplex side; collisions on the half-duplex side
C. collisions on the half-duplex side; framing errors on the full-duplex side
D. collisions on the half-duplex side; giants on the full-duplex side
Answer: C
Explanation:
On an Ethernet connection, a duplex mismatch is a condition where two connected devices operate
in different duplex modes, that is, one operates in half duplex while the other one operates in full
duplex. This results in the full-duplex side receiving an incomplete frame with CRC error or a runt
frame. It does not detect any collision since CSMA/CD is disabled on the full-duplex side. As a
result, when both devices are attempting to transmit at (nearly) the same time, the packet sent by
the fullduplex end will be discarded and lost due to an assumed collision and the packet sent by
the half duplex device will be delayed or lost due to a CRC error in the frame.
https://en.wikipedia.org/wiki/Duplex_mismatch
QUESTION 342
What is correct regarding the configuration shown below?
static route 0.0.0.0/0
qualified-next-hop 172.30.25.1
preference 7 next-hop 172.30.25.5
A. The next-hop 172.30.25.1 is selected because the address has the lowest value.
B. The next-hop 172.30.25.1 is selected because it is listed first.
C. The next-hop 172.30.25.1 is selected because it is the lowest protocol preference.
D. The next-hop 172.30.25.5 is selected because it is the lowest protocol preference.
Answer: D
QUESTION 343
After issuing the show interfaces terse command, you notice that the status of one interface is "up
down". What does this indicate?
A. Layer 1 on the interface is up but Layer 2 is down.

B. Layer 2 on the interface is up but Layer 3 has not been configured.
C. The interface is administratively up but the link status is down.
D. The interface is up but has been administratively turned off.
Answer: C
Explanation:
http://www.juniper.net/documentation/en_US/junos15.1/topics/task/verification/t1status-
displaying.html
QUESTION 344
Which command would initiate a loopback on a Gigabit Ethernet interface ge-0/0/0?
A. # set interfaces ge-0/0/0 unit 0 loopback

B. # set interfaces ge-0/0/0 gigether-options loopback
C. > set interfaces ge-0/0/0 loopback
D. > loopback ge-0/0/0
Answer: B
QUESTION 345
What represents the decimal equivalence of 10101100 00011111 11001001 11000101?
A. 172.28.187.189
B. 172.31.201.197
C. 172.30.231.182
D. 172.19.151.107
Answer: B
QUESTION 346
Which command would allow you to compare two files stored on your router?
A. user@host> file show filename1 compare filename2

B. user@host> file compare files filename1 filename2
C. user@host> compare files filename1 filename2
D. user@host> compare filename1 filename2
Answer: B
QUESTION 347
You are configuring a firewall filter. Which "from" criterion would match only those packets destined
for 10.10.10.1?
A. [edit firewall filter test]

root@router# set term 1 from address 10.10.10.1
B. [edit firewall filter test]
root@router# set term 1 from destination-address 10.10.10.1
C. [edit firewall filter test]
root@router# set term 1 from destination 10.10.10.1
D. [edit firewall filter test]
root@router# set term 1 from ip-prefix 10.10.10.1
Answer: B
QUESTION 348
What is the default local location for syslog and trace files?
A. /log
B. /home/log
C. /var/log
D. /etc/log
Answer: C
QUESTION 349
A router has been configured with the settings shown below:
[edit]
user@host# show system authentication-order
authentication-order [ radius tacplus ];
The router also has a local database that contains the user lab with password lab123. Suppose a
user enters the username lab and the password lab123. What would happen if both the RADIUS
and the TACACS servers are not accessible?
A. The user lab will not be able to login.

B. The user lab will be authenticated against the local database and will be able to login.
C. The user lab will receive an error message indicating the router is unable to authenticate due to the authentication
servers not responding.
D. The user will be able to login only if tries to login as the root user.
Answer: B
QUESTION 350
Which type of routes are held in inet.0?
A. multicast and unicast IPv4 routes

B. ARP tables and MAC reachability
C. IP version 4 unicast routes
D. IP version 6 and IP version 4 routes
Answer: C
QUESTION 351
Which naming convention is used by Juniper Routers when archiving their configurations to a
remote server?
A. yyyymmdd_HHMMSS_host-name_juniper.conf.gz
B. host-name_juniper.conf.gz_yyyymmdd_HHMMSS
C. yyyymmdd_HHMMSS_host-name_juniper.conf
D. host-name_juniper.conf_yyyymmdd_HHMMSS
Answer: ……
Visit PassLeader and Download Full Version JN0-102 Exam Dumps

PassLeader JN0-102 Exam Dumps (301-End)

Uploaded by

Copyright:

Available Formats

PassLeader JN0-102 Exam Dumps (301-End)

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PassLeader JN0-102 Exam Dumps (301-End)

Uploaded by

Copyright:

Available Formats

New VCE and PDF Exam Dumps from PassLeader

➢ Exam Code: JN0-102

➢ Exam Name: Juniper Networks Certified Associate - Junos (JNCIA-Junos)

➢ Questions 301 – End

Visit PassLeader and Download Full Version JN0-102 Exam Dumps

A. It defines which devices will be sending traps.

A. The packets have exceeded the time-to-live value.

A. There is a software issue with ge-1/0/1.0 interface.

Which two steps will accomplish this task? (Choose two.)

A. Create a static route on Router 1 to 172.17.28.1 with a next hop of 10.10.10.2.

A. It will be forwarded to 192.168.100.1 using a metric of 10.

A. The traffic will be rejected.

A. The route 192.168.1.0/25 is accepted.

A. To protect the Routing Engine

A. [edit firewall family inet filter STOP-MAL-USER]

A. [edit firewall family inet filter STOP-MAL-USER]

A. The order of the terms in a policy is irrelevant.

A. A routing policy cannot have more than one term.

A. A single term can be applied to a protocol or interface, independent of the policy.

A. > show interfaces fe-0/0/0 extensive

A. set term match from policy reject

A. show firewall counter telnet-counter filter select-telnet

A. Multiple action modifiers can be included in the same term.

A. Multiple action modifiers can be included in the same term.

A. Packets outside the 10.0.0.0/24 subnet will be accepted.

A. set ip interface ge-0/0/0 address 192.168.1.1 255.255.255.0

A. It will check the MD5 checksum of the install package.

A. lower administrative overhead

A. ping atm vci 0.100 interface at-0/1/0 end-to-end

A. show chassis environment

A. # set ip host-name <name>

A. collisions on the full-duplex side; runts on the half-duplex side

A. Layer 1 on the interface is up but Layer 2 is down.

A. # set interfaces ge-0/0/0 unit 0 loopback

A. user@host> file show filename1 compare filename2

A. [edit firewall filter test]

A. The user lab will not be able to login.

A. multicast and unicast IPv4 routes

Visit PassLeader and Download Full Version JN0-102 Exam Dumps

You might also like