UNIT-I

LINEAR WAVESHAPING

A linear network is a network made up of linear elements only. A linear network can
be described by linear differential equations. The principle of superposition and the principle
of homogeneity hold good for linear networks. In pulse circuitry, there are a number of
waveforms, which appear very frequently. The most important of these are sinusoidal, step,
pulse, square wave, ramp, and exponential waveforms. The response of RC, RL, and RLC
circuits to these signals is described in this chapter. Out of these signals, the sinusoidal signal
has a unique characteristic that it preserves its shape when it is transmitted through a linear
network, i.e. under steady state, the output will be a precise reproduction of the input
sinusoidal signal. There will only be a change in the amplitude of the signal and there may be
a phase shift between the input and the output waveforms. The influence of the circuit on the
signal may then be completely specified by the ratio of the output to the input amplitude and
by the phase angle between the output and the input. No other periodic waveform preserves
its shape precisely when transmitted through a linear network, and in many cases the output
signal may bear very little resemblance to the input signal.
The process whereby the form of a non-sinusoidal signal is altered by transmission
through a linear network is called linear wave shaping.
THE HIGH-PASS RC CIRCUIT
Figure 1.30 shows a high-pass RC circuit. At zero frequency the reactance of the capacitor is
infinity and so it blocks the input and hence the output is zero. Hence, this capacitor is called
the blocking capacitor and this circuit, also called the capacitive coupling circuit, is used to
provide dc isolation between the input and the output. As the frequency increases, the
reactance of the capacitor decreases and hence the output and gain increase. At very high
frequencies, the capacitive reactance is very small so a very small voltage appears, across C
and, so the output is almost equal to the input and the gain is equal to 1. Since this circuit
attenuates low-frequency signals and allows transmission of high-frequency signals with little
or no attenuation, it is called a high-pass circuit.

Sinusoidal Input
Figure (a) shows the Laplace transformed high-pass RC circuit. The gain versus frequency
curve of a high-pass circuit excited by a sinusoidal input is shown in Figure (b). For a
sinusoidal input v,, t;he output signal v0 increases in amplitude with increasing frequency.
The frequency at which the gain is 1/V2 of its maximum value is called the lower cut-off or
lower 3-dB frequency. For a high-pass circuit, there is no upper cut-off frequency because all
high frequency signals are transmitted with zero attenuation. Therefore, f2 – f1. Hence
bandwidth B.W= f2 – f1 =∞
Expression for the lower cut-off frequency
For the high-pass RC circuit shown in Figure (a), the magnitude of the steady-state gain A,
and the angle θ by which the output leads the input are given by

This is the expression for the lower cut-off frequency of a high-pass circuit.

High pass RC circuit response to Step input Voltage:

RC high-pass filter

A step waveform is defined by the following expression:

 Fig:a The step waveform Fig:b Output waveform

The generalized transient expression has been derived at,

--- (1)
The expression for v (t) can be found if we know the initial condition v (0) final condition v
(), and the time constant ‘RC’ of the circuit.

--- (2)
The output waveform for the step input to an RC high pass fitter is an exponentially falling
waveform as shown in Fig. (b). This response reaches almost zero after a time ‘t’ greater than
‘5RC’.
High pass RC circuit response to pulse input:

A positive pulse is mathematically represented as the combination of a positive step followed

by a delayed negative step i.e., vi = Vu(t) − Vu(t − tp) where, tp is the duration of the pulse as
shown in Fig.
To understand the response of a high-pass circuit to this pulse input, let us trace the
sequence of events following the application of the input signal.
At t = 0, vi abruptly rises to V. As a capacitor is connected between the input and output, the
output also changes abruptly by the same amount. As the input remains constant, the output
decays exponentially to V1 at t = tp. Therefore,

At t = tp, the input abruptly falls by V, vo also falls by the same amount. In other words,
vo = V1 − V. Since V1 is less than V; vo is negative and its value is V2 and this decays to zero
exponentially. For t > tp,

then
 The response of high-pass circuits with different values of τ to pulse input is plotted in
Fig below. As is evident from the preceding discussion, when a pulse is passed through a
high-pass circuit, it gets distorted. Only when the time constant τ is very large, the shape of
the pulse at the output is preserved, as can be seen from Fig (b). However, as shown in
Fig (c), when the time constant τ is neither too small nor too large, there is a tilt (also called a
sag) at the top of the pulse and an under-shoot at the end of the pulse. If τ << tp, as in Fig (d),
the output comprises a positive spike at the beginning of the pulse and a negative spike at the
end of the pulse. In other words, a high-pass circuit converts a pulse into spikes by employing
a small time constant; this process is called peaking.
 If the distortion is to be negligible, τ has to be significantly larger than the duration of
the pulse. In general, there is an undershoot at the end of the pulse. The larger the tilt (for
small τ), the larger the undershoot and the smaller the time taken for this undershoot to decay
to zero. The area above the reference level (A1) is the same as the area below the reference
level (A2). Let us verify this using below Fig
Area A1: For 0 < t < tp:
vo = Ve−t/τ
 Similarly,

So that,

Fig:The calculation of A1 and A2

High pass RC circuit response to Square input:

A waveform that has constant amplitude, say, V′ for a time T1 and has another constant
amplitude, V′′ for a time T2, and which is repetitive with a time T = ( T1+ T2), is called a
square wave. In a symmetric square wave, T1=T2 = T/2. Figure 1.10 shows typical input –
output waveforms of the high - pass circuit when a square wave is applied as the input signal.

As the capacitor blocks the DC, the DC component in the output is zero. Thus, as expected,
even if the signal at the input is referenced to an arbitrary dc level, the output is always
referenced to the zero level. It can be proved that whatever the dc component associated with
a periodic input waveform, the dc level of the steady - state output signal for the high - pass
circuit is always zero as shown in Fig. 1.10. To verify this statement, we write the KVL
equation for the high – pass circuit:

q
vi   vo
c

where, q is the charge on the capacitor. Differentiating with respect to t:

dvi 1 dq dvo
 
dt C dt dt
 dq
But i 
dt

Substituting this condition in above Eq, then

dvi i dvo
 
dt C dt

Since vo = iR, i = vo/R and RC = τ. Therefore,

dvi vo dvo
  
dt  dt

Multiplying by dt and integrating over the time period T we get:

T

 dv
0
i  [vi ]T0  vi (T )  vi (0)

T T
v0 1

0
dt 
  v dt
0
0

 dv
0
o  [v0 ]T0  v0 (T )  v0 (0)

Fig: A typical steady - state output of a high - pass circuit with a square wave as input
T
1
vi (T )  vi (0)   v0 dt  [v0 (T )  v0 (0)]
 0

Under steady state conditions, the output and the input waveforms are repetitive with a time
Period T. Therefore, vi(T) =vo(T) and vi(0) =vo(0). Hence, from the above Eq.
As the area under the output waveform over one cycle represents the DC component in the
output, from above Eq. it is evident that the DC component in the steady-state is always zero.
Now let us consider the response of the high-pass RC circuit for a square-wave input for
different values of the time constant τ, as shown in below Fig.

As is evident from the waveform in Fig.(b), there is no appreciable distortion in the

output if τ is large. The output is almost the same as the input except for the fact that there is
no DC component in the output. As τ decreases, as in Fig. (c), there is a tilt in the positive
duration (amplitude decreases from V1 to V1′ during the period 0 to T1) and there is also a tilt
in the negative duration (amplitude increases from V2 to V2′ during the period T1 to T2). A
further decrease in the value of τ [see Fig. (d)] gives rise to positive and negative spikes.
There is absolutely no resemblance between the signals at the input and the output. However,
this condition is imposed on high-pass circuits to derive spikes. In case a pulse is required to
trigger another circuit, we see that the pulses obtained either at the rising edge (positive
spike) or at the trailing edge (negative spike) may be used to edge trigger a flip-flop.
Let us consider the typical response of the high-pass circuit for a square-wave input shown in
Fig below

From the above fig

........... (a)

For a symmetric square wave T1 = T2 = T/2. And, because of symmetry:

...............(b)

From Eq (a)

But

Therefore,

................(c)

From Eq (b) V1 = −V2

Substituting in Eq. (c):

V1e−T1/τ + V1 = V = V1(1 + e−T1/τ) = V

Thus

For a symmetric square wave, as T1 = T2 = T/2, then from above Eq. (2.39) we can written
as:
But

There is a tilt in the output waveform. The percentage tilt, P, is defined as:

If T/2τ << 1,

Therefore

Thus, for a symmetrical square wave:

Above Eq tells us that the smaller the value of τ when compared to the half-period of the
square wave (T/2), the larger is the value of P. In other words, distortion is large with small τ
and is small with large τ. The lower half-power frequency, f1 = 1/2πτ.

Therefore,

So P = πf1T × 100%
Therefore

High pass RC circuit response to ramp input Voltage:

A waveform which is defined as: Vi(t) = { 0 for t< 0

t for t > 0

Then the output is Vo(t) = i(t ) R

Fig. High pass RC circuit

Which becomes

This equation has the solution for V(t) at t = 0. Taking Laplace Transform on both sides of
the above equation becomes

By taking Inverse Laplace Transform,

For times ‘t’ <<RC,

 The output signal falls away slightly from the input. As a measure of the departure
from linearity let us define the transmission error et , as the difference between input and
output divided by the input. The error at a time t = T, is then

where f1 =1/2RC is again the low frequency 3-dB point.

Response of the High-pass RC Circuit to Exponential Input:

When a pulse is applied as input to an amplifier, it may while appearing at the actual input
terminals of the amplifier, have a finite rise time. The result is that the input to the amplifier
is
no longer a pulse with sharp rising edge, but an exponential. We would now like to know the
response of the high-pass circuit to this exponential input. If the input to the high-pass circuit
in Fig below is an exponential of the form:
 Exponential input

We know

.......................(d)

As vi = V(1 − e−t/τ1),

Substituting above Eq. in Eq. (d): then

Taking Laplace transform on both sides:

where, τ is the time constant of the high-pass circuit.

Therefore
Case 1: τ = τ1
Applying partial fractions, above Eq. can be written as:

Therefore

Put s = −1/τ1 in above Eq.

Now put s = −1/τ, then

Therefore

Substituting the values of A and B in Vo(s):

Taking inverse Laplace transform:

This is the expression for the output voltage where τ ≠ τ1.

Let t/τ1 = x and τ/τ1 = n. For n ≠ 1, i.e., τ ≠ τ1, we have from above Eq:

Therefore

If τ >> τ1, the second term in the above Eq.is small when compared to the first. Thus,

Case 2: τ = τ1, that is, n = 1.

Taking Laplace inverse:

As t/τ = x = t/τ1 and τ/τ1 = n = 1:

The response of the circuit is plotted for different values of n in Fig. below

Fig: Response of a high-pass circuit to an exponential input

Since x = t/τ, from above Eq., the time taken to rise to the peak tp is given by:

From above Eq.

To obtain the maximum value of the output, substitute this value of −x from above Eq. in the
expression for vo(t) in below Eq.

From the waveforms in above Figure and the subsequent mathematical relations
derived, it is seen that, if an exponential signal is applied as an input to a high-pass circuit,
the output is a pulse whose duration depends on n (= τ/τ1), where τ1 is the time constant of
the previous circuit that has generated the exponential signal and τ is the time constant of the
high-pass circuit under consideration. The smaller the value of n, the smaller the duration of
this output pulse and also the smaller its amplitude. As n increases, the duration as well as the
amplitude of this output pulse increases. Hence, depending on our requirement, we adjust the
value of n.
DIFFERENTIATORS
Sometimes, a square wave may need to be converted into sharp positive and negative spikes
(pulses of short duration). By eliminating the positive spikes, we can generate a train of
negative spikes and vice-versa. The pulses so generated may be used to trigger a
multivibrator. In such cases, a differentiator is used. If in a circuit, the output is a differential
of the input signal, then the circuit is called a differentiator.
A High-pass RC Circuit as a Differentiator
If the time constant of the high-pass RC circuit, shown in Fig. 1.1(a), is much smaller than the
time period of the input signal, then the circuit behaves as a differentiator. If T is to be large
when compared to τ, then the frequency must be small. At low frequencies, XC is very large
when compared to R. Therefore, the voltage drop across R is very small when compared to
the drop across C.

But iR = vo is small. Therefore,

FIGURE: The output of a differentiator

Differentiating:

Therefore
Thus, from above Eq., it can be seen that the output is proportional to the differential of the
input signal.

THE LOW-PASS RC CIRCUIT

Figure 1.1 shows a low-pass RC circuit. A low-pass circuit is a circuit, which transmits only
low-frequency signals and attenuates or stops high-frequency signals.

At zero frequency, the reactance of the capacitor is infinity (i.e. the capacitor acts as an open
circuit) so the entire input appears at the output, i.e. the input is transmitted to the output with
zero attenuation. So the output is the same as the input, i.e. the gain is unity. As the frequency
increases the capacitive reactance (Xc = H2nfC) decreases and so the output decreases.
At very high frequencies the capacitor virtually acts as a short-circuit and the output falls to
zero.

Sinusoidal Input
The Laplace transformed low-pass RC circuit is shown in Figure (a). The gain versus
frequency curve of a low-pass circuit excited by a sinusoidal input is shown in Figure
(b).This curve is obtained by keeping the amplitude of the input sinusoidal signal constant
and varying its frequency and noting the output at each frequency. At low frequencies the
output is equal to the input and hence the gain is unity. As the frequency increases, the output
decreases and hence the gain decreases. The frequency at which the gain is l/√2 (= 0.707) of
its maximum value is called the cut-off frequency. For a low-pass circuit, there is no lower
cut-off frequency. It is zero itself. The upper cut-off frequency is the frequency (in the high-
frequency range) at which the gain is 1/√2 . i-e- 70.7%, of its maximum value. The
bandwidth of the low-pass circuit is equal to the upper cut-off frequency f2 itself.

For the network shown in Figure 1.2(a), the magnitude of the steady-state gain A is given by
Step-Voltage Input
A step signal is one which maintains the value zero for all times t < 0, and maintains the
value V for all times t > 0. The transition between the two voltage levels takes place at t = 0
and is accomplished in an arbitrarily small time interval. Thus, in Figure (a), vi = 0
immediately before t = 0 (to be referred to as time t = 0-) and vi = V, immediately after t= 0
(to be referred to as time t = 0+). In the low-pass RC circuit shown in Figure 1.1, if the
capacitor is initially uncharged, when a step input is applied, since the voltage across the
capacitor cannot change instantaneously, the output will be zero at t = 0, and then, as the
capacitor charges, the output voltage rises exponentially towards the steady-state value V
with a time constant RC as shown in
Figure (b).

Let V’ be the initial voltage across the capacitor. Writing KVL around the loop in Fig 1.1.
Expression for rise time
When a step signal is applied, the rise time tr is defined as the time taken by the output
voltage waveform to rise from 10% to 90% of its final value: It gives an indication of how
fast the circuit can respond to a discontinuity in voltage. Assuming that the capacitor is
initially uncharged, the output voltage shown in Figure (b) at any instant of time is given by
This indicates that the rise time tr is proportional to the time constant RC of the circuit. The
larger the time constant, the slower the capacitor charges, and the smaller the time constant,
the faster the capacitor charges.

Relation between rise time and upper 3-dB frequency

We know that the upper 3-dB frequency (same as bandwidth) of a low-pass circuit is

Thus, the rise time is inversely proportional to the upper 3-dB frequency. The time constant
(Τ= RC) of a circuit is defined as the time taken by the output to rise to 63.2% of the
amplitude of the input step. It is same as the time taken by the output to rise to 100% of the
amplitude of the input step, if the initial slope of rise is maintained. See Figure (b). The Greek
letter T is also employed as the symbol for the time constant.

Pulse Input
The pulse shown in Figure (a) is equivalent to a positive step followed by a delayed negative
step as shown in Figure (b). So, the response of the low-pass RC circuit to a pulse for times
less than the pulse width tp is the same as that for a step input and is given by v0(t) = V(l – e-
t/RC
). The responses of the low-pass RC circuit for time constant RC » tp, RC smaller than tp
and RC very small compared to tp are shown in Figures (c), (d), and (e) respectively.
If the time constant RC of the circuit is very large, at the end of the pulse, the output voltage
will
be Vp(t) = V(1 – e-tp/RC) and the output will decrease to zero from this value with a time
constant
RC as shown in Figure (c). Observe that the pulse waveform is distorted when it is passed
through a linear network. The output will always extend beyond the pulse width tp, because
whatever charge has accumulated across the capacitor C during the pulse cannot leak off
instantaneously.
If the time constant RC of the circuit is very small, the capacitor charges and discharges very
quickly and the rise time tr will be small and so the distortion in the wave shape is small. For
minimum distortion (i.e. for preservation of wave shape), the rise time must be small
compared to the pulse width tp. If the upper 3-dB frequency /2 is chosen equal to the
reciprocal of the pulse width tp, i.e. if f2 = 1/tp then tr = 0.35tp and the output is as shown in
Figure 1.5(b), which for many applications is a reasonable reproduction of the input. As a
rule of thumb, we can say:

A pulse shape will be preserved if the 3-dB frequency is approximately equal to the
reciprocal of the pulse width.
Thus to pass a 0.25 μ.s pulse reasonably well requires a circuit with an upper cut-off
frequency of the order of 4 MHz.
Square-Wave Input
A square wave is a periodic waveform which maintains itself at one constant level V’ with
respect to ground for a time T1 and then changes abruptly to another level V", and remains
constant at that level for a time T2, and repeats itself at regular intervals of T = T1 + T2. A
square wave may be treated as a series of positive and negative steps.
 The shape of the output waveform for a square wave input depends on the time constant of
the circuit. If the time constant is very small, the rise time will also be small and a reasonable
reproduction of the input may be obtained.

For the square wave shown in Figure (a), the output waveform will be as shown in Figure (b)
if the time constant RC of the circuit is small compared to the period of the input waveform.
In this case, the wave shape is preserved. If the time constant is comparable with the period
of the input square wave, the output will be as shown id Figure (c). The output rises and falls
exponentially. If the time constant is very large compared to the period of the input
waveform, the output consists of exponential sections, which are essentially linear as
indicated in
Figure (d). Since the average voltage across R is zero, the dc voltage at the output is the same
as that of the input. This average value is indicated as Vdc in all the waveforms.
When the time constant is very small relative to the total ramp time T, the ramp will be
transmitted with minimum distortion. The output follows the input but is delayed by one time
constant RC from the input (except near the origin where there is distortion) as shown in
Figure (a). If the time constant is large compared with the sweep duration, i.e. if RCIT » 1,
the output will be highly distorted as shown in Figure (b).

This shows that a quadratic response is obtained for a linear input and hence the circuit acts
as an integrator for RC/T » 1.
The transmission error et for a ramp input is defined as the difference between the input and
the output divided by the input at the end of the ramp, i.e. at t = T.
For RC/T « 1,

where f2 is the upper 3-dB frequency. For example, if we desire to pass a 2 ms pulse with
less than 0.1% error, the above equation yields f2 > 80 kHz and RC < 2 μ.s.
Exponential Input
For the low-pass RC circuit shown in Figure 1.1, let the input applied as shown in Figure 1.8
be vi(t ) = V(l – e-tlτ), where T is the time constant of the input waveform.
These are the expressions for the voltage across the capacitor of a low-pass RC circuit excited
by an exponential input of rise time tr1 - 2.2r.
If an exponential of rise time tr1 is passed through a low-pass circuit with rise time tr2, the
rise time of the output waveform tr will be given by an empirical relation, tr =1.05√tr12 + tr22
.This is same as the rise time obtained when a step is applied to a cascade of two circuits of
rise times tr1 and tr2 assuming that the second circuit does not load the first.

THE LOW-PASS RC CIRCUIT AS AN INTEGRATOR

If the time constant of an RC low-pass circuit is very large, the capacitor charges very slowly
and so almost all the input voltage appears across the resistor for small values of time.

As time increases, the voltage drop across C does not remain negligible compared with that
across R and the output will not remain the integral of the input. The output will change from
a quadratic to a linear function of time.
If the time constant of an RC low-pass circuit is very large in comparison with the. time
required for the input signal to make an appreciable change, the circuit acts as an
integrator.
A criterion for good integration in terms of steady-state analysis is as follows: The low-pass
circuit acts as an integrator provided the time constant of the circuit RC > 15T, where T is the
period of the input sine wave. When RC > 15T, the input sinusoid will be shifted at least by
89.4° (instead of the ideal 90° shift required for integration)
when it is transmitted through the network.
An RC integrator converts a square wave into a triangular wave. Integrators are almost
invariably preferred over differentiators in analog computer applications for the following
reasons:

1. It is easier to stabilize an integrator than a differentiator because the gain of an integrator

decreases with frequency whereas the gain of a differentiator increases with frequency.
2. An integrator is less sensitive to noise voltages than a differentiator because of its limited
bandwidth.
3. The amplifier of a differentiator may overload if the input waveform changes very rapidly.
4. It is more convenient to introduce initial conditions in an integrator.

Attenuators

An attenuator is a circuit that reduces the amplitude of the signal by a finite amount.
A simple resistance attenuator is represented in the below Fig. The output of the attenuator
shown in Fig. is given by the relation:

From this equation, it is evident that the output is smaller than the input, which is the
main purpose of an attenuator—to reduce the amplitude of the signal. Attenuators are used
when the signal amplitude is very large. Let us measure a voltage, say, 5000 V, using a CRO;
such a large voltage may not be handled by the amplifier in a CRO. Therefore, to be able to
measure such a voltage we first attenuate the voltage by a known amount, say by a factor of
10(α = 0.1), so that the voltage that is actually connected to the CRO is only 500 V. The
output of the attenuator is thus reduced depending on the choice of R1 and R2.

FIGURE: A resistance attenuator

FIGURE(a): The attenuator output connected to amplifier input

Uncompensated Attenuators
If the output of an attenuator is connected as input to an amplifier with a stray capacitance C2
and input resistance Ri, as shown in Fig.(a).
 Consider the parallel combination of R2 and Ri. If the amplifier input is not to load
the attenuator output, then Ri should always be significantly greater than R2. The attenuator
circuit is now shown in Fig.(b).
Reducing the two-loop network into a single-loop network by Thevenizing:

And Rth = R1||R2

Hence, the circuit in Fig.(b) reduces to that shown in Fig. (c).
When the input αvi is applied to this low-pass RC circuit, the output will not reach the
steady-state value instantaneously. If, for the above circuit, R1 = R2 = 1 MΩ and C2 = 20 nF,
the rise time is:
tr = 2.2 RthC2 = 2.2 × 0.5 × 106 × 20 × 10−9
tr = 22ms
This means that after a time interval of approximately 22ms after the application of
the input αvi to the circuit, the output reaches the steady-state value. This is an abnormally
long delay. An attenuator of this type is called an uncompensated attenuator, i.e., its output is
dependent on frequency.

FIGURE (b): The attenuator, considering the stray capacitance at the amplifier input

FIGURE (c): An uncompensated attenuator

Compensated Attenuators
To make the response of the attenuator independent of frequency, the capacitor C1 is
connected acrossR1. This attenuator now is called a compensated attenuator shown in below
Fig. (d). This circuit in Fig. (d) is redrawn as shown in below Fig. (e).

FIGURE (d) A compensated attenuator

FIGURE (e) Redrawn circuit of Fig (d)

FIGURE (f) The compensated attenuator open-circuiting the xy branch

In Figs. (d) and (e), R1, R2, C1, C2 form the four arms of the bridge. The bridge is said to be
balanced when R1C1 = R2C2, in which case no current flows in the branch xy. Hence, for
the purpose of computing the output, the branch xy is omitted. The resultant circuit is shown
in Fig. (f).

When a step voltage with vi = V is applied as an input, the output is calculated as follows: At
t = 0+, the capacitors do not allow any sudden changes in the voltage; as the input changes,
the output should also change abruptly, depending on the values of C1 and C2.

Thus, the initial output voltage is determined by C1 and C2. As t → ∞, the capacitors are
fully charged and they behave as open circuits for dc. Hence, the resultant output is:

Perfect compensation is obtained if, vo(0+) = vo(∞)

From this using above Eqs., we get:
and the output is αvi.

FIGURE (g) A perfectly compensated attenuator (C1 = C2)

FIGURE (h) An over-compensated attenuator (C1 > C2)

FIGURE (i) An under-compensated attenuator (C1 < C2)

Let us consider the following circuit conditions:

1. When C1 = Cp, the attenuator is a perfectly compensated attenuator.

2. When C1 > Cp, it is an over-compensated attenuator.

3. When C1 < Cp, it is an under-compensated attenuator.

The response of the attenuator to a step input under these three conditions is shown in Figs.
(g),(h) and (i), respectively.

In the attenuator circuit, as at t = 0+, the capacitors C1 and C2 behave as short circuits, the
current must be infinity. But impulse response is impossible as the generator, in practice, has
a finite source resistance, not ideally zero. Now consider the compensated attenuator with
source resistance Rs [see Fig. (j)].
If the xy loop is open for a balanced bridge, Thevenizing the circuit, the Thevenin voltage
source and its internal resistance and R′ are calculated using Fig. (k).

FIGURE (j) The attenuator taking the source resistance into account

FIGURE (k) The circuit used to calculate the Thevenin voltage source and its internal
resistance

FIGURE (i) Redrawn circuit of Fig.(k)

The value of Thevenin voltage source is:
and its internal resistance is:

The above circuit now reduces to that shown in above Fig. (i). Usually Rs (R1 + R2), hence,
Rs || (R1 + R2) ≈ Rs.
This is a low-pass circuit with time constant τs = RsCs, where Cs is the series combination of
C1 and C2; Cs= C1C2/(C1 + C2). The output of the attenuator is an exponential with time
constant τs; and if τs is small, the output almost follows the input.

A perfectly compensated attenuator is sometimes used to reduce the signal amplitude when
the signal is connected to a CRO to display a waveform. A typical CRO probe may be
represented as in below Fig.

RL and RLC circuits:

RL High pass filter: It is an electronic circuit which allows all the inputs with frequencies
greater than a particular frequency called the cut-off frequency to pass through it.

Transfer Function

Fig. RL High Pass Circuit

𝑗𝜔𝐿
𝑣0 (𝜔) = 𝑣𝑖 (𝜔).
𝑅 + 𝑗𝜔𝐿

𝑣0 (𝜔) 𝑗𝜔𝐿
𝐻(𝜔) = =
𝑣𝑖 (𝜔) 𝑅 + 𝑗𝜔𝐿

𝑣0 (𝜔) 𝑗𝜔𝐿
|𝐻(𝜔)| = | |=| |
𝑣𝑖 (𝜔) 𝑅 + 𝑗𝜔𝐿

𝜔𝐿
|𝐻(𝜔)| =
√𝑅 2 + 𝜔 2 𝐿2
 𝜔𝐿/𝑅
|𝐻(𝜔)| =
√1 + 𝜔 2 (𝐿/𝑅)2

2ᴨ𝑓𝐿/𝑅
|𝐻(𝜔)| =
√1 + 4ᴨ𝑓 2 (𝐿/𝑅)2

Frequency Response:

1 𝑓/𝑓𝑙
If 𝑓𝑙 = 𝐿 |𝐻(𝜔)| =
2ᴨ( ) √1+(𝑓/𝑓𝑙 )2
𝑅

If 𝑓 ≪ 𝑓𝑙 (𝑓/𝑓𝑙 )2 ≪ 1 |𝐻(𝜔)| = 𝑓/𝑓𝑙

As frequency increases |𝐻(𝜔)| also increases and the rate of increase in 20dB/decade.

1
If 𝑓 = 𝑓𝑙 (𝑓/𝑓𝑙 )2 = 1 |𝐻(𝜔)| =
√2

If 𝑓 ≫ 𝑓𝑙 (𝑓/𝑓𝑙 )2 ≫ 1 |𝐻(𝜔)| = 1

|𝐻(𝜔)|
1
0.707

𝑓ℎ f
Fig. Frequency Response
The frequency response indicates that the frequencies below 𝑓𝑙 will be blocked by the circuit
and the frequencies above 𝑓𝑙 will be transmitted. This shows that the circuit is indeed a
Highpass filter.

Response of RL Highpass filter to a step input:

𝑣𝑖 (𝑡) = 𝐴𝑢(𝑡)

𝐴
𝑣𝑖 (𝑠) =
𝑠

𝐿𝑠
𝑣0 (𝑠) = 𝑣𝑖 (𝑠)
𝑅 + 𝐿𝑠

𝐴 𝐿𝑠
=
𝑠 𝑅 + 𝐿𝑠

1
=𝐴
𝑅/𝐿 + 𝑠

1
𝑣0 (𝑠) = 𝐴
𝑠 + 𝑅/𝐿
 𝑡𝑅
𝑣0 (𝑡) = 𝐴. 𝑒 − 𝐿 𝑢(𝑡)

𝑣𝑖 (𝑡)= 𝐴𝑢(𝑡)

𝑡𝑅 t
𝑣0 (𝑡) = 𝐴. 𝑒 − 𝐿 𝑢(𝑡)
A

Fig. Response of RL High pass filter to a step input

RL Low pass filter: It is an electronic circuit which allows all the inputs with frequencies
lesser than a particular frequency called the cut-off frequency to pass through it.

Transfer Function

Fig. RL Low pass filter

𝑅
𝑣0 (𝜔) = 𝑣𝑖 (𝜔).
𝑅 + 𝑗𝜔𝐿

𝑣0 (𝜔) 𝑅
𝐻(𝜔) = =
𝑣𝑖 (𝜔) 𝑅 + 𝑗𝜔𝐿

𝑣0 (𝜔) 𝑅
|𝐻(𝜔)| = | |=| |
𝑣𝑖 (𝜔) 𝑅 + 𝑗𝜔𝐿

𝑅
|𝐻(𝜔)| =
√𝑅 2 + 𝜔 2 𝐿2

1
|𝐻(𝜔)| =
√1 + 𝜔 2 (𝐿/𝑅)2
 1
|𝐻(𝜔)| =
√1 + 4ᴨ𝑓 2 (𝐿/𝑅)2

Frequency Response:

1 1
If 𝑓ℎ = 𝐿 |𝐻(𝜔)| =
2ᴨ( ) √1+(𝑓/𝑓ℎ )2
𝑅

If 𝑓 ≪ 𝑓ℎ (𝑓/𝑓ℎ )2 ≪ 1 |𝐻(𝜔)| = 1

1
If 𝑓 = 𝑓ℎ (𝑓/𝑓ℎ )2 = 1 |𝐻(𝜔)| =
√2

If 𝑓 ≫ 𝑓𝑙 (𝑓/𝑓ℎ )2 ≫ 1 |𝐻(𝜔)| = 𝑓ℎ /𝑓

As frequency increases |𝐻(𝜔)| also decreases and the rate of decrease in 20dB/decade.

|𝐻(𝜔)|
1
0.707

𝑓𝑙 f

Fig. Frequency Response

The frequency response indicates that the frequencies below 𝑓𝑙 will be transmitted by the
circuit and the frequencies above 𝑓𝑙 will be blocked. This shows that the circuit is indeed a
Lowpass filter.

Response of RL Lowpass filter to a step input:

𝑣𝑖 (𝑡) = 𝐴𝑢(𝑡)

𝐴
𝑣𝑖 (𝑠) =
𝑠

𝑅
𝑣0 (𝑠) = 𝑣𝑖 (𝑠)
𝑅 + 𝐿𝑠

𝐴 𝑅
=
𝑠 𝑅 + 𝐿𝑠

𝐴 𝑅/𝐿
=
𝑠 𝑅/𝐿 + 𝑠

𝐴1 𝐴2
= +
𝑠 𝑅/𝐿 + 𝑠

𝐴 −𝐴
= +
𝑠 𝑅/𝐿 + 𝑠
 𝑡𝑅
𝑣0 (𝑡) = 𝐴𝑢(𝑡) − 𝐴. 𝑒 − 𝐿 𝑢(𝑡)

𝑡𝑅
𝑣0 (𝑡) = 𝐴(1 − 𝑒 − 𝐿 )𝑢(𝑡)

𝑣𝑖 (𝑡)= 𝐴𝑢(𝑡)
𝐴

𝑡𝑅 t
𝑣0 (𝑡) = 𝐴(1 − 𝑒 − 𝐿 )𝑢(𝑡)

t
Fig. Response of RL Low pass filter to a step input

Series RLC Circuit:

Fig. Series RLC Circuit

Response of series RLC circuit to a step input:

𝑣𝑖 (𝑡) = 𝐴𝑢(𝑡)

𝐴
𝑣𝑖 (𝑠) =
𝑠

1⁄
𝑣0 (𝑠) = 𝑣𝑖 (𝑠) 𝑠𝐶
𝑅 + 𝐿𝑠 + 1⁄𝑠𝐶

𝐴 1⁄
𝑣0 (𝑠) = 𝑠𝐶
𝑠 𝑅 + 𝐿𝑠 + 1⁄
𝑠𝐶

1⁄
= 𝐿𝐶
𝑅 1
𝑠 (𝑠 2 + 𝑠 𝐿 + 𝐿𝐶 )
 1 𝑅 𝐶
If 𝝎𝒏 𝟐 = 𝐿𝐶, Ԑ = 2 √𝐿

𝝎𝒏 𝟐
𝑣0 (𝑠) =
𝑠(𝑠 2 + 2Ԑ𝝎𝒏 𝑠 + 𝝎𝒏 𝟐 )

Case-1:

𝑅 𝐶
If Ԑ = 1 √ =1
2 𝐿

𝝎𝒏 𝟐
𝑣0 (𝑠) =
𝑠(𝑠 2 + 2𝝎𝒏 𝑠 + 𝝎𝒏 𝟐 )

𝝎𝒏 𝟐
=
𝑠(𝑠 + 𝝎𝒏 )2

𝐴 𝐵 𝐶
= + +
𝑠 𝑠 + 𝜔𝑛 (𝑠 + 𝜔𝑛 )2

𝐴 = 1, 𝐵 = −1 𝑎𝑛𝑑 𝐶 = −𝜔𝑛

1 −1 −𝜔𝑛
= + +
𝑠 𝑠 + 𝜔𝑛 (𝑠 + 𝜔𝑛 )2

𝑣0 (𝑡) = (1 − 𝑒 −𝜔𝑛 𝑡 − 𝜔𝑛 𝑡𝑒−𝜔𝑛 𝑡 )𝑢(𝑡)

𝑣0 (0) = 0

𝑣0 (∞) = 1

𝑣𝑖 (𝑡)= 𝐴𝑢(𝑡)
𝐴

𝑣0 (𝑡) t

Fig. Response of series RLC circuit to a step input for case 1

Case-2:

𝑅 𝐶
If Ԑ > 1 √ >1
2 𝐿

𝝎𝒏 𝟐
𝑣0 (𝑠) =
𝑠(𝑠 2 + 2Ԑ𝝎𝒏 𝑠 + 𝝎𝒏 𝟐 )

𝑠 2 + 2Ԑ𝝎𝒏 𝑠 + 𝝎𝒏 𝟐 = (𝒔 − {−Ԑ𝝎𝒏 + 𝝎𝒏 √Ԑ2 − 1}) (𝒔 − {−Ԑ𝝎𝒏 − 𝝎𝒏 √Ԑ2 − 1}})

𝐴 𝐵 𝐶
𝑣0 (𝑠) = + +
𝑠 𝒔 − {−Ԑ𝝎𝒏 + 𝝎𝒏 √Ԑ2 − 1} 𝒔 − {−Ԑ𝝎𝒏 − 𝝎𝒏 √Ԑ2 − 1}

On solving

1 1
𝐴 = 1, 𝐵 = 𝑎𝑛𝑑 𝐶 =
2(Ԑ2 − 1 − Ԑ√Ԑ2 − 1) 2(Ԑ2 − 1 + Ԑ√Ԑ2 − 1)

1 1 1
𝑣0 (𝑠) = +
𝑠 2(Ԑ2 − 1 − Ԑ√Ԑ2 − 1) 𝒔 − {−Ԑ𝝎𝒏 + 𝝎𝒏 √Ԑ2 − 1}
1 1
+
2(Ԑ2 − 1 + Ԑ√Ԑ2 − 1) 𝒔 − {−Ԑ𝝎𝒏 − 𝝎𝒏 √Ԑ2 − 1}

2 2
1 𝑒 (−Ԑ𝝎𝒏 +𝝎𝒏 √Ԑ −1)𝒕 𝑒 (−Ԑ𝝎𝒏 −𝝎𝒏 √Ԑ −1)𝒕
𝑣0 (𝑡) = 𝑢(𝑡) + [ + ] 𝑢(𝑡)
2 (Ԑ2 − 1 − Ԑ√Ԑ2 − 1) (Ԑ2 − 1 + Ԑ√Ԑ2 − 1)

𝑣0 (0) = 0

𝑣0 (∞) = 1

Case-3:

𝑅 𝐶
If Ԑ < 1 √ <1
2 𝐿

𝜔𝑛 2
𝑣0 (𝑠) =
𝑠(𝑠 2 + 2Ԑ𝜔𝑛 𝑠 + 𝜔𝑛 2 )

𝑠 2 + 2Ԑ𝜔𝑛 𝑠 + 𝜔𝑛 2 = (𝑠 − {−Ԑ𝜔𝑛 + 𝜔𝑛 √Ԑ2 − 1}) (𝑠 − {−Ԑ𝜔𝑛 − 𝜔𝑛 √Ԑ2 − 1}})

𝜔𝑛 2
𝑣0 (𝑠) =
𝑠(𝑠 − {−Ԑ𝜔𝑛 + 𝜔𝑛 √Ԑ2 − 1})(𝑠 − {−Ԑ𝜔𝑛 − 𝜔𝑛 √Ԑ2 − 1}})
 √Ԑ2 −1
−Ԑ𝜔𝑛 + 𝜔𝑛 √Ԑ2 − 1 in polarform can be written as 𝜔𝑛 𝑒 −𝑗𝛼 𝛼 = tan−1 ( Ԑ
)

−Ԑ𝜔𝑛 − 𝜔𝑛 √Ԑ2 − 1 in polarform can be written as 𝜔𝑛 𝑒 +𝑗𝛼

𝜔𝑛 2
𝑣0 (𝑠) =
𝑠(𝑠 − 𝜔𝑛 𝑒 −𝑗𝛼 )(𝑠 − 𝜔𝑛 𝑒 +𝑗𝛼 )

𝐴 𝐵 𝐶
𝑣0 (𝑠) = + −𝑗𝛼
+
𝑠 𝑠 − 𝜔𝑛 𝑒 𝑠 − 𝜔𝑛 𝑒 +𝑗𝛼
On solving
𝑒 +𝑗𝛼 𝑒 −𝑗𝛼
𝐴 = 1, 𝐵 = ,𝐶 =
−2𝑗 sin 𝛼 2𝑗 sin 𝛼

1 𝑒 +𝑗𝛼 1 𝑒 −𝑗𝛼 1
𝑣0 (𝑠) = +( )( ) + ( ) ( )
𝑠 −2𝑗 sin 𝛼 𝑠 − 𝜔𝑛 𝑒 −𝑗𝛼 2𝑗 sin 𝛼 𝑠 − 𝜔𝑛 𝑒 +𝑗𝛼

𝑒 +𝑗𝛼 −𝑗𝛼 𝑒 −𝑗𝛼 +𝑗𝛼

𝑣0 (𝑡) = 𝑢(𝑡) + ( ) 𝑒 𝜔𝑛𝑒 𝑡 𝑢(𝑡) + ( ) 𝑒 𝜔𝑛𝑒 𝑡 𝑢(𝑡)
−2𝑗 sin 𝛼 2𝑗 sin 𝛼

𝑒 +𝑗𝛼 2 𝑒 −𝑗𝛼 2
𝑣0 (𝑡) = 𝑢(𝑡) + ( ) 𝑒 −Ԑ𝜔𝑛 𝑡+𝜔𝑛 √Ԑ −1𝑡 𝑢(𝑡) + ( ) 𝑒 −Ԑ𝜔𝑛 𝑡−𝜔𝑛 √Ԑ −1𝑡 𝑢(𝑡)
−2𝑗 sin 𝛼 2𝑗 sin 𝛼

2 +𝛼) 2 +𝛼)
𝑒 −Ԑ𝜔𝑛 𝑡 𝑒 𝑗(𝜔𝑛 𝑡√1−Ԑ + 𝑒 −𝑗(𝜔𝑛 𝑡√1−Ԑ
𝑣0 (𝑡) = 1 − [ ]
sin 𝛼 2𝑗

𝑒 −Ԑ𝜔𝑛 𝑡
𝑣0 (𝑡) = 1 − [sin(𝜔𝑛 𝑡√1 − Ԑ2 + 𝛼)]
sin 𝛼

𝑒 −Ԑ𝜔𝑛 𝑡
𝑣0 (𝑡) = 1 − [sin(𝜔𝑛 𝑡√1 − Ԑ2 + 𝛼)]
√1 − Ԑ2

Fig. Response of series RLC circuit to a step input for three different cases
 𝑑𝑣0 (𝑡)
𝑖0 (𝑡) = 𝐶
𝑑𝑡

Parallel RLC Circuit:

Fig. Parallel RLC circuit

Response of Parallel RLC circuit to a step input:

As the parallel RLC circuit is a dual of the series RLC circuit. So the output voltage of it will
have the same shape as the current waveform of the series RLC circuit. The same is presented
in below Fig.
Similarly the output current waveform of Parallel RLC circuit will have the same shape as the
voltage waveform of the series RLC circuit. The same is presented in below Fig.

Ringing Circuit :
Ringing circuits are those which generate a sequence of pulses spaced regularly in time these
circuits have un damped oscillations depending on the number of ringing duty cycles
required. The parallel and Series RLC circuits can be considered as the ringing circuits.
 UNIT - I
LINEAR WAVESHAPING
Pulse Circuits

Assignment-Cum-Tutorial Questions
A. Questions testing the remembering / understanding level of students
I) Objective Questions
1. The waveform which preserves its form when transmitted through a linear network is
a___________. []

a)Sine wave b) Step signal c) impulse signal d) ramp signal

2. The rise time of the output of a low pass RC circuit is given by []

a) 2.2 RC b) 0.35/fH c) 2.2τ d) all the above

3. What is the response of step input to a high pass RC circuit [ ]

a) Ve -t/RC b) V(1- e t/RC ) c) V e t/RC d) V(1- e -t/RC )

4. What is peaking?

The process of converting pulses into pipsby means of a circuit with very small time
constant is known as Peaking.

5. What is the name of the circuit which converts square wave into spikes ? [
]

a) Low pass RC b) Bistable multi c) High pass RC d)

Monoshot

6. In RC integrator circuit the output is taken across CAPACITOR

7. RC << T is the condition for an high pass RC circuit to act as a differentiator.

8. The process of converting pulses into spikes is called Peaking.

9. Write the relationship between time constant and tilt? % tilt (P) = T/(2RC) x 100

10. What is the condition for an RC low pass circuit to act as an integrator?RC >>15 T

11. The output of an RC differentiating circuit is V0 = RC (dVi /dt)

12. If the time constant of an RC low-pass circuit is very large in comparison with the time
required for the input signal to make an appreciable change, then the ciruit is called as an
Integrator.

II) Descriptive Questions

1. Prove that an RC circuit behaves as a reasonably good integrator if RC > 15T, Where
T is the period of an input ‘Em sin ωt’.
 2. Draw the output waveform of an RC high-pass circuit with a square wave input under
different time constants. Derive the expression for percentage of tilt.

3. Analyze the responses of RC low-pass circuit for the following inputs:

a) Step input b) Pulse input

4. Analyze the responses of RC high-pass circuit for the following inputs:

a) Step input b) Pulse input

5. Explain how the low-pass RC circuit acts as integrator and high-pass RC circuit acts
as differentiator.

6. Obtain the expression for the gain A and phase angle Φ of an RC low pass and high
pass circuist. Sketch the frequency response and find the expression for higher &
lower cutoff frequencies.

7. Draw the output waveform of an RC low -pass circuit with a square wave input under
different time constants.

B. Question testing the ability of students in applying the concepts.

I) Multiple Choice Questions:
1. 1. An RC high pass circuit has R= 1kΩ and C=0.5 μF. Its lower cutoff frequency is [ ]

(a) Zero (b) 318.3 Hz (c) 1 kHz (d) infinity

2. An RC low pass circuit has R= 1kΩ and C=0.5 μF. Its rise time is []

(a) 1.1 msec (b) 2.2 msec (c) 3.3msec (d) 0.5 msec

3. An RC low pass circuit has R= 0.5kΩ and C=1 μF. Its lower cutoff frequency is []

(a) Zero (b) 318.3 Hz (c) 1 kHz (d) infinity

4. An RC low pass circuit has cut-off frequency 2KHz and time period of 3µsec then
what is the phase angle of the circuit?

f = 1/T = 1/3x10-6 = 333KHz

Ɵ = tan-1(f/fH) = tan-1(333K/2K) = tan-1(166.5) =89.65º
5. Rise time of low pass filter is 0.5nsec.Find the bandwidth ? []

(a) 0.7 GHz (b) 0.9 GHz (c) 70 MHz (d) 600 MHz

6. For a 0.5µsec pulse to be reproduced with minimum distortion, the rise time of the
low-pass RC circuit must be [
]

(a) 0.35µsec (b) 0.175 µsec (c) 1µsec (d) none of these

7. The bandwidth of a low-pass RC circuit is 1 KHz. What is the rise time of the output
for a step input ?
[ ]
 (a) 0.35 msec (b) 1 msec (c) 0.35 sec (d) none of these

II) Problems:
1. A 10Hz symmetrical square wave whose peak-to-peak amplitude is impressed upon
RC high-pass circuit whose lower 3-db is 5Hz.Calculate and sketch the output
waveform.

2. A square wave whose peak-to-peak value is 1V extends to ±0.5V with reference to

the ground. The half-period is 0.1sec and impressed on the RC differentiator circuit
whose time constant is 0.2sec. Determine the maximum and minimum values of the
output voltage at steady state.

3. A symmetrical square wave of 20V peak to peak amplitude with zero average value
and with a time period of 2µsec is given as input of an RC low pass circuit whose
upper 3 dB is 1/2п M Hz .Calculate and sketch steady state output wave form .In
particular what is the peak to peak output amplitude.

4. Calculate the lowest square wave frequency that can be passed by an amplifier with a lower
cut-off frequency of 10 Hz, if the output tilt is not to exceed 2%.

5. A step generator of 50 ohm impedance applies a 10V step of 2.2 nsec rise time to a
series combination of a capacitor C and R=50 ohm. A pulse of amplitude 1V appears
across R. Find the value of the capacitance C.

6. An RC differentiator circuit is driven from a 500 Hz symmetrical square wave of 10V

peak-to-peak. Calculate the output voltage levels under steady state if RC=1 msec.

7. A 10Hz symmetrical square wave whose peak-to-peak amplitude is 2 V is impressed

upon a high pass RC circuit whose 3-dB frequency is 5Hz. Calculate and sketch the
output waveform.

8. Determine the upper 3-dB frequency for low pass RC circuit, if a pulse of 0.4µsec is
required to pass without distortion. Find the value of resistance if the capacitor is
0.001uF.

9. A 1KHz square wave output from an amplifier has rise time 350nsec and tilt is 5%
Determinethe upper and lower 3 dB frequencies.

10. A pulse is applied to a integrator.Prove that the area under the pulse is same as that of
the area under output waveform across the capacitor.