Engineering Design Guidelines Process Flow Sheet

Page : 1 of 94
KLM Technology Rev: 02

Group
Practical Engineering www.klmtechgroup.com Rev 01 March 2015
Guidelines for Processing
Plant Solutions Rev 02 Nov 2015
Solutions, Standards and Software
KLM Technology Co Author:

Group Kolmetz Handbook
Rev 01 Aprilia Jaya
#03-12 Block Aronia, of Process Equipment Design Rev 02 Riska Ristiyanti
Jalan Sri Perkasa 2
Taman Tampoi Utama
81200 Johor Bahru PROCESS FLOW SHEET Author / Editor
Malaysia
Karl Kolmetz
(ENGINEERING DESIGN GUIDELINE)
KLM Technology Group has developed; 1) Process Engineering Equipment

Design Guidelines, 2) Equipment Design Software, 3) Project Engineering
Standards and Specifications, and 4) Unit Operations Manuals. Each has
many hours of engineering development.
KLM is providing the introduction to this guideline for free on the internet.
Please go to our website to order the complete document.
www.klmtechgroup.com
TABLE OF CONTENT
INTRODUCTION 4
Scope 4
General Design Consideration 5
DEFINITIONS 23
KLM Technology Page 2 of 94
of Process Equipment Design Rev: 02
Practical Engineering
Guidelines for PROCESS FLOW SHEET
Processing Plant Nov 2015
Solutions
(ENGINEERING DESIGN GUIDELINES)
NOMENCLATURE 26
THEORY OF THE DESIGN 27
Kind of Lines and Symbols 28
Instrumentation Design 41
Process Flow Diagram (PFD) 44
Piping and Instrument Diagram (P&ID) 51
A. Guideline for drafting 52

B. Equipment, Instrumentation and Piping Indication 54
C. General Notes 62
D. Establishment of P&IDs Preparation Steps 64
Line Schedule 71
REFEREENCES 68
LIST OF TABLE
Table 1: Commercial process simulation programs 19

Table 2. Flowsheet flags of operating conditions in typical units 31
Table 3: Functional symbols for control 42
Table 4: Minimum Information Requirements for Equipment 47
Table 5: Pipeline Symbols 48
Table 6: Equipment symbols 49
Table 7: information of equipment in P&ID 55
These design guideline are believed to be as accurate as possible, but are very general and not for specific design
cases. They were designed for engineers to do preliminary designs and process specification sheets. The final
design must always be guaranteed for the service selected by the manufacturing vendor, but these guidelines will
greatly reduce the amount of up front engineering hours that are required to develop the final design. The guidelines
are a training tool for young engineers or a resource for engineers with experience.
This document is entrusted to the recipient personally, but the copyright remains with us. It must not be copied,
reproduced or in any way communicated or made accessible to third parties without our written consent.
Solutions
LIST OF FIGURE
Figure 1: Block flow diagram of Ammonia Process 7

Figure 2: Pictorial flow diagram establishes key processing steps 8
Figure 3: Process flow diagram of desulfurization 10
Figure 4: Typical P&ID arrangement for three phase separator vessels 14
Figure 5: Piping details isometric diagram 15
Figure 6: Standard type layout for service piping diagram 16
Figure 7: Typical process area plot plan and study elevations 18
Figure 8: Flowsheet: polymer production 19
Figure 9: A typical simulation program 21
Figure 10: Flow chart of steps in simulation 22
Figure 11: Process equipment variables symbols 31
Figure 12: Instrument Symbols 36
Figure 13: Symbol of (a) instrument, (b) cascade control, and
(c) compound control 43
Figure 14: Measuring devices (a) Flow rate measuring and (b) Level
Measuring 44
Figure 15: Symbol of lines and equipments in P&ID 68
Figure 16: Centrifugal pump schedule data sheet 76
Figure 17: Effluent schedule data sheet 77
Figure 18: Line schedule data sheet 78
Figure 19: Another line schedule data sheet 79
Figure 20: Mass balance schedule data sheet 80
Figure 21: Vessel and tank schedule data sheet 81
Figure 22: Tower overhead data sheet 82
Solutions
Figure 23: Pipeline data sheet 83

Figure 24: Vessel data sheet 84
Figure 25: Heat exchanger data sheet 85
Figure 26: Relief valve data sheet 86
Figure 27: Control valve data sheet 87
Figure 28: Pump data sheet 88
Solutions
KLM Technology Group is providing the introduction to this guideline for free on
the internet. Please go to our website to order the complete document.
www.klmtechgroup.com
INTRODUCTION
Scope
This design guideline covers the basic elements of Process Flow Sheets in sufficient
detail to allow an engineer to design a flow sheet with the suitable symbols of
equipment, line, indicator and control.
The flow sheet is the key document in process design. Flowsheets are intended to
represent and explain processes. It shows the arrangement of the equipment selected
to carry out the process, the stream connections, stream flow rates and compositions,
and the operating conditions. Process flow sheets embody the material and energy
balances between and the sizing of the major equipment of the plant.
The flow sheet is drawn up from material balances made over the complete process
and each individual unit operation. Energy balances are also made to determine the
energy flows and the utility requirements. As the process flow sheet is the definitive
document on the process, the presentation must be clear, comprehensive, accurate,
and complete. The various types of flow sheets are discussed in this guideline. In this
section, there are tables that assist in making these flow sheets from the vary reference
sources. All the important parameters use in the guideline are explained in the definition
section which help the reader more understand the meaning of the parameters or the
term used.
The theory section explained about kind of lines, equipments, indicator and controller
symbols, instrumentation design, process flow diagram, piping and instrument diagram,
data sheet examples, engineering ethics, standards and codes. The examples of the
data sheets will make the engineer easier to understand.
Solutions
General Design Consideration
The flowsheet is the key document in process design. It shows the arrangement of the
equipment selected to carry out the process, the stream connections, stream flow rates
and compositions, and the operating conditions. It is a diagrammatic model of the
process. The flowsheet is used by specialist design groups as the basis for their
designs.
These include piping, instrumentation, and equipment design and plant layout. It is also
used by operating personnel for the preparation of operating manuals and operator
training. During plant startup and subsequent operation, the flowsheet forms a basis for
comparison of operating performance with design. The flowsheet is drawn up from
material balances made over the complete process and each individual unit operation.
Energy balances are also made to determine the energy flows and the utility
requirements.
The amount of information shown on a flowsheet will depend on the custom and
practice of the particular design office. The following list has therefore been divided into
essential items and optional items. The essential items must always be shown; the
optional items add to the usefulness of the flowsheet but are not always included
Essential Information
1. Stream composition, either

i. the flow rate of each individual component, kg/h, or
ii. the stream composition as a weight fraction.
2. Total stream flow rate, kg/h;
3. Stream temperature,
4. Nominal operating pressure (the required operating pressure);
5. Stream enthalpy, kJ/h.
Solutions
Optional Information
1. Molar percentage composition and/or molar flow rates;

2. Physical property data, mean values for the stream, such as
i. density, kg/m3
ii. viscosity, mN s/m2.
3. Stream name, a brief, one- or two-word description of the nature of the stream,
As the process flowsheet is the definitive document on the process, the presentation
must be clear, comprehensive, accurate, and complete. The various types of flowsheets
are discussed in the following
1. Block Diagrams
A block diagram is the simplest form of presentation. Each block can represent a single
piece of equipment or a complete stage in the process. They are useful for showing
simple processes. With complex processes, their use is limited to showing the overall
process, broken down into its principal stages. This is usually used to set forth a
preliminary or basic processing concept without details. The blocks do not describe how
a given step will be achieved, but rather what is to be done.
Block diagrams are also useful for representing a process in a simplified form in reports,
textbooks, and presentations, but have only limited use as engineering documents. The
stream flow rates and compositions can be shown on the diagram adjacent to the
stream lines, when only a small amount of information is to be shown, or tabulated
separately. Block diagrams are often drawn using simple graphics programs.
A good BFD typically contains the following:
• Large individual pieces of equipment, or equipment as part of a combined

process, that are denoted by a single symbol, typically a rectangle
• Clear labels illustrating function (since no equipment or package numbers appear
on this document)
• The order of process flow arranged from left to right and, if possible, with a
gravity basis, i.e, if hydrocarbons are shown entering a separation process, then
Solutions
gas leaving the process should be shown exiting from the top of the block and
condensate from the bottom
• Lines linking equipment or processes to show flow direction
• Wherever more than one line leaves a process, then the processed commodity in
each line should be clearly marked
Figure 1: Block flow diagram of Ammonia Process
Solutions
2. Pictorial Representation
On the detailed flowsheets used for design and operation, the equipment is normally
drawn in a stylized pictorial form. For tender documents or company brochures, actual
scale drawings of the equipment are sometimes used, but it is more usual to use a
simplified representation. There are several international standards for PFD symbols,
but most companies use their own standard symbols, as the cost of converting all of
their existing drawings would be excessive. ISO 10628 is the international standard for
PFD drawing symbols.
3. Process Flowsheet or Flow Diagram (PFD)
Process flow diagram is a schematic representation of the sequence of all relevant

operations occurring during a process and includes information considered desirable for
analysis. It can be defined as an operation occurring when an object (or material) is
intentionally changed in any of its physical or chemical characteristics, is assembled or
disassembled from another object or is arranged or prepared for another operation,
transportation, inspection or storage.
PFD shows the plant design basis indicating feedstock, product and main streams flow
rates and operating conditions. This is used to present the heat balance and material
balance of a process. This may be in broad block form with specific key points
delineated, or in more detailed form identifying essentially every flow, temperature, and
pressure for each basic piece of process equipment or processing step. PFD shows
graphically the arrangement of major equipment, process lines and main control loops.
This may and usually does include auxiliary services to the process, such as steam,
water, air, fuel gas, refrigeration, circulating oil, and so on. This type of sheet is not
necessarily distributed to the same groups, because it may contain detailed confidential
process data.
A typical PFD shows the following items:
• Process piping
• Process flow direction
• Major equipment represented by simplified symbols
• Major bypass and recirculation lines
Solutions
• Control and process-critical valves

• Processes identified by system name
• System ratings and operational values
• Compositions of fluids
• Connections between systems.
Figure 3: Process flow diagram of desulfurization
Solutions
4. Piping Flowsheet or Mechanical Flow Diagram or Piping and Instrumentation

Diagram (P&ID)
The Piping and Instrument Diagram (P&ID), based on the Process Flow Diagram (PFD),
represents the technical realization of a process by means of graphical symbols for
equipment and piping as well as graphical symbols for process measurement and
control functions. This is used to present “mechanical-type” details to piping and
mechanical vessel designers, electrical engineers, instrument engineers, and other
engineers not directly in need of process details.
Piping and Instrument Diagrams are graphical summary of the actual hardware
elements in a chemical process plant and their interrelationships of connections to form
an operable, safe, and reliable plant. They do not show operating conditions or
compositions or flow quantities, but they do show all major as well as minor equipment
more realistically than on the process flowsheet. Included are sizes and specification
classes of all pipe lines, all valves, and all instruments. The P&IDs include vessels
(columns and tanks), pipe sizes, schedule (thickness), materials of construction, all
valves (sizes and types), pumps, heat exchangers, reactors, furnaces, compressors,
expanders, relief and drain valves, traps, filters, conveyors, hoppers, purchased
subsystems, sensors, insulation requirements (thickness and type), controllers (flow,
pressure, temperature, level), spares, and other manufactured items, all in a logical
configuration. The P&IDs do not include piping lengths and bends. In some engineering
systems, detailed specifications cannot be completed until this flowsheet is basically
complete.
A P&ID carries a wealth of information that spans engineering disciplines to define a

process. It is the best way of accurately documenting the operation of a process, and it
is truly a coordinating document. P&IDs take the conceptual aspects of the PFD and
expand them by adding:
• Detailed symbols
• Detailed equipment information
• Equipment order and process sequence
• Process and utility (non-process) piping
• Process flow direction
Solutions
• Major and minor bypass lines

• Line numbers, pipe specifications, and pipe sizes
• Isolation and shutoff valves
• Maintenance vents and drains
• Relief and safety valves
• Instrumentation
• Controls
• Types of process component connections
• Vendor and contractor interfaces
• Skid and package interfaces
• Hydrostatic vents and drains
• Design requirements for hazardous operations.
Piping and Instrument Diagrams will be sub-divided between the categories described
below. However combination is permissible when a unit is of such a size and design
that for example, the utilities and auxiliaries can be shown on one type of diagram with
clarity.
1. Process Unit P&ID's
P&ID's of a particular unit such as a compressor, and inlet filter scrubber unit are called
Process Unit P&ID's.
2. Utility P&ID's
P&ID's of utilities such as instrument air and oil system, oily water and waste water, and
tempered water are called Utility P&ID's.
3. Distribution P&ID's
P&ID's of header distribution systems shown geographically are called Distribution

P&ID's. It should be noted that the system need not necessarily be limited to utility
distribution and can be used for process distribution.
Solutions
The Distribution P&ID shall not duplicate any valves or instrumentation already shown
on other P&ID's. The Distribution P&ID for each system shall contain the following
information:
• Size, service, line number, whether insulated and type of tracing and Piping Material
Specification of headers, sub-headers and lines to individual equipment items.
• Valves at headers (usually for isolation purposes).
• Instruments for header system control.
• Battery limit identification to show proper connection to offsite lines.
• P&ID number and equipment tag number for lines going to Process Unit/Utility
P&ID's.
4. Auxiliary P&ID's
P&ID's of the equipment piping and instrumentation associated with an item of

equipment are called Auxiliary P&ID's. A typical example would be the auxiliary
equipment, piping and instrumentation necessary for a large compressor. The intent is
to keep the Process Unit P&ID's as uncluttered as possible. The Auxiliary P&ID's shall
show auxiliary equipment, utility piping etc. and the following information:
• Piping, instrumentation etc. to be supplied by Vendor.

• Cross references to the vendor's terminal connection designation.
5. Packaged Unit P&ID's
P&ID's provided by equipment suppliers for a packaged unit e.g. large centrifugal
compressor unit etc. are called Packaged Unit P&ID's. Contractor P&ID's shall indicate
the package unit by enclosing the appropriate part of the P&ID concerned with a dash-
dot line to show the exact scope of supply. The space enclosed shall state the package
unit tag number and the titles of all equipment included with the suppliers name and
drawing number. The Vendor P&ID shall be marked up by Contractor to show:
• Package unit tag number

• Tag numbers of all equipment (where allocated) and instruments
• Drawing number allocated by Contractor
Solutions
• The letters "Contractor’s name” in brackets shown against any items supplied by
Contractor
• All other comments required to bring the P&ID into line with Project standards
6. Symbols P&ID's
P&ID's containing general notes, symbols, nomenclature and piping details are called
Symbols P&ID's.
Figure 4: Typical P&ID arrangement for 3 phase separator vessels
Solutions
5. Combined Process and Piping Flowsheet or Diagram
This is used to serve the combined purpose of both the process and the piping
flowsheets. This necessarily results in a drawing with considerably more detail than
before types. The advantage is in concentrating the complete data and information for a
project at one point. It does require close attention in proper reading and often opens
data to larger groups of persons who might misinterpret or misuse it. it presents a
concise summary of the complete process and key mechanical data for assembly. This
type of sheet requires more time for complete preparation, but like all engineering
developments preliminary issues are made as information is available. Often the sheet
is not complete until the piping and other detailed drawings are finished. This then is an
excellent record of the process as well as a worksheet for training operators of the plant.
Solutions
Figure 5: Piping details isometric diagram
Solutions
6. Utility Flowsheets or Diagrams
Utility line diagram (ULD) includes hardware details of the steam, water piping, and
control systems. Used to summarize and detail the interrelationship of utilities such as
air, water (various types), steam (various types), heat transfer mediums, process vents
and purges, safety relief blow-down, and so on to the basic process. The amount of
detail is often too great to combine on other sheets, so separate sheets are prepared.
These are quite valuable and time saving during the engineering of the project. They
also identify the exact flow direction and sequence of tie-in relationships for the
operating and maintenance personnel. The distribution of a utility such as steam is by a
common distribution pipe, with each unit requiring the utility drawing its supply from that
pipe. When a unit has taken its requirement, the utility distribution pipe can then be
reduced in size as it continues to the next unit requiring the utility. The order of servicing
units is affected by layout, and utility line sizes are affected by the order.
Solutions
Figure 6: Standard type layout for service piping diagram
Solutions
7. Special Flowsheets or Diagrams
From the basic process containing flowsheet, other engineering specialties develop
their own details. For example, the instrument engineer often takes the requirements of
the process and prepares a completely detailed flowsheet which defines every action of
the instruments, control valves, switches, alarm horns, signal lights, and so on. This is
his/her detailed working tool. The electrical engineer likewise takes basic process and
plant layout requirements and translates them into details for the entire electrical
performance of the plant. This will include the electrical requirements of the
instrumentation in many cases, but if not, they must be coordinated.
8. Special or Supplemental Aids – Plot Plans
Plot plans are necessary for the proper development of a final and finished process,
piping, or utility flowsheet. After broad or overall layout decisions are made, the detailed
layout of each processing area is not only helpful but necessary in determining the first
realistic estimate of the routing, lengths, and sequence of piping. This is important in
such specifications as pipe sizing, and pump head and compressor discharge
pressures. The nature of the fluids – whether hazardous, toxic, and so on – as well as
the direction or location or availability for entrance to the area, definitely influences
decisions regarding the equipment layout on the ground, in the structures, and in
relation to buildings. Prevailing wind direction and any other unusual conditions should
also be considered.
Solutions
Figure 7: Typical process area plot plan and study elevations
Solutions
Presentation of Stream Flow Rates
The data on the flow rate of each individual component, on the total stream flow rate,
and the percentage composition can be shown on the flowsheet in various ways. The
simplest method, suitable for simple processes with few pieces of equipment, is to
tabulate the data in blocks alongside the process stream lines. The initial layout of the
key equipment should be spread farther than looks good to the eye. In fact, it probably
looks wasteful of drawing space. Later as process and sometimes service lines, valves,
controls, and miscellaneous small accessories are added this “extra” space will be
needed to maintain an easily readable sheet. As this develops, attention should be
given to the relative weights and styles of lines to aid in the readability of the sheets.
Figure 8: Flowsheet: polymer production
Solutions
Process Simulation Programs
Most flowsheet calculations are carried out using commercial process simulation
programs. The process simulation programs contain models for most unit operations as
well as thermodynamic and physical property models. All the commercial programs
feature some level of custom modeling capability that allows the designer to add models
for nonstandard operations.
The principal advantage of simultaneous, dynamic simulators is their ability to model the
unsteady-state conditions that occur at startup and during fault conditions. The program
consists of
1. A main executive program that controls and keeps track of the flowsheet calculations
and the flow of information to and from the subroutines.
2. A library of equipment performance subroutines (modules) that simulate the
equipment and enable the output streams to be calculated from information on the
inlet streams.
3. A data bank of physical properties. To a large extent, the utility of a sophisticated flow
sheeting program depends on the comprehensiveness of the physical property data
bank. The collection of the physical property data required for the design of a
particular process and its transformation into a form suitable for a particular flow
sheeting program can be very time-consuming.
4. Subroutines for thermodynamics, such as the calculation of vapor-liquid equilibrium
and stream enthalpies.
5. Subprograms and data banks for equipment sizing and costing. Process simulation
programs enable the designer to consider alternative processing schemes, and the
cost routines allow quick economic comparisons to be made. Some programs include
optimization routines. To make use of a costing routine, the program must be capable
of producing at least approximate equipment designs.
Solutions
Figure 9: A typical simulation program
In a sequential-modular program, the executive program sets up the flowsheet

sequence, identifies the recycle loops, and controls the unit operation calculations, while
interacting with the unit operations library, physical property data bank, and the other
subroutines. The executive program also contains procedures for the optimum ordering
of the calculations and routines to promote convergence. In an equation-oriented
simulator, the executive program sets up the flowsheet and the set of equations that
describe the unit operations and then solves the equations using data from the unit
operations library and the physical property data bank and calling on the file of
thermodynamics subroutines. All process simulators use graphical user interfaces to
display the flowsheet and facilitate the input of information to the package.
Solutions
Modeling and simulation procedure
• Translating the description of a physical system into an appropriate mathematical

form.
• Selecting a suitable computational technique.
• Implementing the computational technique in the form of a computer program
Solutions
Define process
Develop math model
Identify constraint
Develop computer
program
Run simulation program
No All parameters
covered?
Yes
Do model and No
ex. agree?
Yes
Determine optimum
conditions
Figure 10: Flow chart of steps in simulation
Solutions
DEFINITIONS
Actuators - a type of motor that is responsible for moving or controlling a mechanism or

system. It is operated by a source of energy, typically electric current, hydraulic fluid
pressure, or pneumatic pressure, and converts that energy into motion.
Cascade control - An automatic control system in which various control units are linked
in sequence, each control unit regulating the operation of the next control unit in line
Control loops - One segment of a process control system. An open-loop control

process requires human intervention, whereas a closed-loop system is entirely
automated
Control system - a device, or set of devices, that manages, commands, directs or

regulates the behavior of other devices or systems. Industrial control systems are used
in industrial production for controlling equipment or machines.
Distillation - The process of separating materials by successively heating to vaporize a

portion and then cooling to liquefy a part of the vapor. Materials to be separated must
differ in boiling point and/or relative volatility.
Electrical drawings—symbols and diagrams that depict an electrical process.
Elevation drawings—a graphical representation that shows the location of process

equipment in relation to existing structures and ground level.
Equipment location drawings—show the exact floor plan for location of equipment in
relation to the plan’s physical boundaries.
Evaporators - a device used to turn the liquid form of a chemical into its gaseous form.
The liquid is evaporated, or vaporized, into a gas.
Field separator - A vessel in the oil or gas field for separating gas, hydrocarbon liquid,
and water from each other.
Solutions
Flow diagram—a simplified sketch that uses symbols to identify instruments and
vessels and to describe the primary flow path through a unit.
Flowsheet - a graphic representation, using symbols interconnected with lines, of the

successive steps in a procedure or system. Also called flow′ diagram.
Foundation drawings—concrete, wire mesh, and steel specifications that identify

width, depth, and thickness of footings, support beams, and foundation.
Fractionation - Generally used to describe separation of a mixture of hydrocarbons into

individual products based on difference in boiling point and/or relative volatility
Gas injection - The injection of natural gas into a reservoir to maintain or increase the
reservoir pressure or reduce the rate of decline of the reservoir pressure
Legends—a document used to define symbols, abbreviations, prefixes, and specialized

equipment.
Licenser - A company duly organized and existing under the laws of the said
company’s country and as referred to in the preamble to the contract.
Packaged Unit P&ID's - P&ID's provided by equipment suppliers for a packaged unit
e.g. large centrifugal compressor unit etc
Pipeline - a line of pipe with pumps, valves, and control devices for conveying liquids,
gases, or finely divided solids
Piping and Instrument Diagram (P&ID) - a diagram in the process industry which
shows the piping of the process flow together with the installed equipment and
instrumentation.
Plant layout - the most effective physical arrangement, either existing or in plans of
industrial facilities i.e. arrangement of machines, processing equipment and service
departments to achieve greatest co-ordination and efficiency of 4 M’s (Men, Materials,
Machines and Methods) in a plant.
Plot Plan- The plot plan is the scaled plan drawing of the processing facility.
Solutions
Pneumatic - a section of technology that deals with the study and application of
pressurized gas to produce mechanical motion. Pneumatic systems used extensively in
industry are commonly powered by compressed air or compressed inert gases.
Process and instrument drawing (P&ID)—a complex diagram that uses process
symbols to describe a process unit; also called piping and instrumentation drawing.
Process flow diagram - a diagram commonly used in chemical and process

engineering to indicate the general flow of plant processes and equipment. The PFD
displays the relationship between major equipment of a plant facility and does not show
minor details such as piping details and designations. Another commonly used term for
a PFD is a flowsheet.
Process simulation - a model-based representation of chemical, physical, biological,

and other technical processes and unit operations in software. Basic prerequisites are a
thorough knowledge of chemical and physical properties of pure components and
mixtures, of reactions, and of mathematical models which, in combination, allow the
calculation of a process in computers.
Project- the equipment, machinery and materials to be procured by the contractor and
the works and/or all activities to be performed and rendered by the contractor in
accordance with the terms and conditions of the contract documents.
Reflux - In fractionation, the portion of condensed overhead returned to the column to

enhance achievable purity of the overhead product.
Unit- one or all process, offsite and/or utility Units and facilities as applicable to form a
complete operable oil, gas and/or petrochemical plant.
Valve - a device that regulates, directs or controls the flow of a fluid (gases, liquids,
fluidized solids, or slurries) by opening, closing, or partially obstructing various
passageways.
Solutions
NOMENCLATURE
SCFM gas flow rate

ΔP pressure drop
ID internal diameter (in)
OD outer diameter (in)
GPM volume flow rate (gpm)
T temperature (F)
H enthalpy (btu/lb)
P pressure (psig)
PC pressure controller
TC Temperature controller
FC Flow controller
LC level controller

Engineering Design Guidelines Process Flow Sheet

Uploaded by

Copyright:

Available Formats

Engineering Design Guidelines Process Flow Sheet

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Engineering Design Guidelines Process Flow Sheet

Uploaded by

Copyright:

Available Formats

Page : 1 of 94

KLM Technology Rev: 02

KLM Technology Co Author:

KLM Technology Group has developed; 1) Process Engineering Equipment

General Design Consideration 5

THEORY OF THE DESIGN 27

Kind of Lines and Symbols 28

Process Flow Diagram (PFD) 44

Piping and Instrument Diagram (P&ID) 51

A. Guideline for drafting 52

Table 1: Commercial process simulation programs 19

Figure 1: Block flow diagram of Ammonia Process 7

Figure 23: Pipeline data sheet 83

General Design Consideration

1. Stream composition, either

1. Molar percentage composition and/or molar flow rates;

A good BFD typically contains the following:

• Large individual pieces of equipment, or equipment as part of a combined

Figure 1: Block flow diagram of Ammonia Process

3. Process Flowsheet or Flow Diagram (PFD)

Process flow diagram is a schematic representation of the sequence of all relevant

A typical PFD shows the following items:

• Control and process-critical valves

Figure 3: Process flow diagram of desulfurization

4. Piping Flowsheet or Mechanical Flow Diagram or Piping and Instrumentation

A P&ID carries a wealth of information that spans engineering disciplines to define a

• Major and minor bypass lines

1. Process Unit P&ID's

P&ID's of header distribution systems shown geographically are called Distribution

P&ID's of the equipment piping and instrumentation associated with an item of

• Piping, instrumentation etc. to be supplied by Vendor.

5. Packaged Unit P&ID's

• Package unit tag number

Figure 4: Typical P&ID arrangement for 3 phase separator vessels

5. Combined Process and Piping Flowsheet or Diagram

Figure 5: Piping details isometric diagram

6. Utility Flowsheets or Diagrams

Figure 6: Standard type layout for service piping diagram

7. Special Flowsheets or Diagrams

8. Special or Supplemental Aids – Plot Plans

Figure 7: Typical process area plot plan and study elevations

Presentation of Stream Flow Rates

Figure 8: Flowsheet: polymer production

Process Simulation Programs

Figure 9: A typical simulation program

In a sequential-modular program, the executive program sets up the flowsheet

Modeling and simulation procedure

• Translating the description of a physical system into an appropriate mathematical

Develop math model

Run simulation program

Figure 10: Flow chart of steps in simulation

Actuators - a type of motor that is responsible for moving or controlling a mechanism or

Control loops - One segment of a process control system. An open-loop control

Control system - a device, or set of devices, that manages, commands, directs or

Distillation - The process of separating materials by successively heating to vaporize a

Electrical drawings—symbols and diagrams that depict an electrical process.

Elevation drawings—a graphical representation that shows the location of process

Flowsheet - a graphic representation, using symbols interconnected with lines, of the

Foundation drawings—concrete, wire mesh, and steel specifications that identify

Fractionation - Generally used to describe separation of a mixture of hydrocarbons into