Basf Masterbrace Adh 1414 Tds 823008

MasterBrace® ADH 1414
Epoxy bonding agent for concrete repairs, bonding concrete to concrete, steel and granolithic
toppings
DESCRIPTION TYPICAL PROPERTIES*

MasterBrace ADH 1414 is a permanent
epoxy adhesive for internal or external Mixed density ASTM D1475 1485kg/m³
bonding of renderings, granolithic toppings, @ 25°C
and concrete to concrete. It tolerates a degree Open time ASTM D2471 25°C 6 hours
of moisture before and during curing and is 40°C 2.5 hours
insoluble when cured. Tack free time ASTM D2471 25°C 9 hours
40°C 5 hours
Full cure ASTM C661 7 days
The ultimate bond strength is greater than the Slant shear bond strength >20N/mm²
tensile strength of concrete. ASTM C882-99
Water absorption ASTM D570 <0.1%
MasterBrace ADH 1414 does not shrink and Compressive strength >50N/mm²
provides an even and stress-free bond. ASTM D695-91
PRIMARY USES APPLICATION PROCEDURE

MasterBrace ADH 1414 may be applied to
clean, sound and durable surfaces, i.e. steel, PREPARATION
glazed tiles and bricks, ceramic and quarry tiles,
All surfaces must be thoroughly cleaned and
terrazzo tiles and floors. Also to smooth and worn
prepared. All loose particles, laitance, dust,
granolithic pavings, old and worn concrete,
curing compounds, floor hardeners, oil, grease,
engineering and semi-engineering bricks.
fat, bitumen and paint must be removed if good
bond strength is to be achieved. Gloss surfaces
ADVANTAGES must be abraded.
 High strength
 Non shrink If oil, grease, fat, etc. are present, they should be
 Moisture tolerant removed before starting any other form of
 Durable preparation. All laitance weak or friable concrete
 Resistant to chemical attack should be removed by chipping, grit blasting, or
 Supplied in pre-weighed units scabbling until a sound base is obtained.
All laitance should be removed by mechanical

PACKAGING
scarification, grit blasting, or by acid etching.
MasterBrace ADH 1414 is available in 3kg units Visible signs of mould growth, lichen, or algae,
containing the base resin and reactor component. should be removed and treated with a fungicidal
wash.
STANDARDS
ASTM C881 Type 2 Grade 2, Class B & C. New concrete should have cured until the
shrinkage and moisture movement is low.
Surfaces heavily impregnated with mould oil
should be degreased and grit blasted or
mechanically scarified to remove the
contaminated surface. All curing compounds
should have disintegrated or be removed and
application carried out only onto a clean, dust free
surface.
MIXING TEMPERATURE
Carefully transfer the entire contents of the Since low temperatures retard the setting and
smaller container of MasterBrace ADH 1414 curing of MasterBrace ADH 1414, avoid
REACTOR COMPONENT to the larger working in cold weather if possible. Although
MasterBrace ADH 1414 COMPONENT tin and MasterBrace ADH 1414 will cure slowly at low
thoroughly mix, using a stout palette knife or a temperatures, a temperature of 7°C to 10°C
slow running drill with a paint mixing paddle can be considered to be the lowest at which
until uniformity is achieved. This normally takes work on vertical rendering may proceed
about three minutes. Do not attempt to mix only satisfactorily without shuttering.
part of the contents. Do not attempt to thin.
EQUIPMENT CARE
GUIDE TO APPLICATION Use MasterTop THN 2 to clean tools when
MasterBrace ADH 1414 should be applied MasterBrace ADH 1414 is still wet or tacky.
evenly across the whole surface with a clean, Once MasterBrace ADH 1414 has set hard, it
short haired paint brush or a laying-on trowel. can only be removed by chipping or burning.
After application, the MasterBrace ADH 1414 COVERAGE

must be left to stand before overcoating. The 2-2.7m²/kg dependent on substrate profile.
time delay will depend on surface and
prevailing conditions but will typically be 60
minutes at 25°C or 45 minutes at 40°C. STORAGE
Store under cover out of direct sunlight and
The MasterBrace ADH 1414 should be protect from extremes of temperature. In
protected during this time to prevent tropical climates the product must be stored in
contamination. This is particularly necessary on an air conditioned environment.
horizontal surfaces.
Failure to comply with the recommended
storage conditions may result in premature
RENDERINGS AND SCREEDS
deterioration of the product or packaging. For
Once the render or screed has been applied specific storage and disposal advice consult
over the MasterBrace ADH 1414 recognised BASF's Technical Services Department.
methods of working may be adopted.
It is essential that granolithic paving and sand
SAFETY PRECAUTIONS
cement renders and screeds are cured. This
can be achieved by curing with a fine spray of As with all chemical products, care should be
clean water and polythene sheeting. More taken during use and storage to avoid contact
effective is to spray the surface with a curing with eyes, mouth, skin and foodstuffs (which
membrane from the MasterKure range. may also be tainted with vapour until product is
Failure to observe these precautions may fully cured). Treat splashes to eyes and skin
cause the render or screed to crack and craze. immediately. If accidentally ingested, seek
immediate medical attention. Reseal containers
Expansion joints formed in the substrate should after use. For further information refer to the
be carried through the rendering or screed and Material Safety Data Sheet.
may be filled with MasterSeal GG 470 (gun
grade) or MasterSeal PG 470 (pouring grade),
2 part polysulphide joint sealant.
NOTE
Field service, where provided, does not
constitute supervisory responsibility. For
additional information contact your local BASF
representative.
BASF reserves the right to have the true cause

of any difficulty determined by accepted test
methods.
QUALITY AND CARE

All products originating from BASF’s Dubai, UAE
facility are manufactured under a management
system independently certified to conform to the
requirements of the quality, environmental and
occupational health & safety standards ISO 9001,
ISO 14001 and OHSAS 18001.
* Properties listed are based on laboratory controlled tests.
® = Registered trademark of the BASF-Group in many countries.
BASF_CC-UAE/Br_1414_12_94/v4/07_17
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.
BASF Construction Chemicals UAE LLC

Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet

Basf Masterbrace Adh 1414 Tds 823008

Uploaded by

Copyright:

Available Formats

Basf Masterbrace Adh 1414 Tds 823008

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basf Masterbrace Adh 1414 Tds 823008

Uploaded by

Copyright:

Available Formats

MasterBrace® ADH 1414

DESCRIPTION TYPICAL PROPERTIES*

PRIMARY USES APPLICATION PROCEDURE

All laitance should be removed by mechanical

After application, the MasterBrace ADH 1414 COVERAGE

BASF reserves the right to have the true cause

QUALITY AND CARE

* Properties listed are based on laboratory controlled tests.

® = Registered trademark of the BASF-Group in many countries.

BASF Construction Chemicals UAE LLC

You might also like