Complementary Symmetry

Push-pull amplifiers use two “complementary” or matching transistors, one being an NPN-
type and the other being a PNP-type with both power transistors receiving the same input
signal together that is equal in magnitude, but in opposite phase to each other. This results in
one transistor only amplifying one half or 180o of the input waveform cycle while the other
transistor amplifies the other half or remaining 180o of the input waveform cycle with the
resulting “two-halves” being put back together again at the output terminal.
Then the conduction angle for this type of amplifier circuit is only 180o or 50% of the input
signal. This pushing and pulling effect of the alternating half cycles by the transistors gives
this type of circuit its amusing “push-pull” name, but are more generally known as the Class
B Amplifier as shown below.
Class B Output Characteristics Curves

The Class B Amplifier has the big advantage over their Class A amplifier cousins in that no
current flows through the transistors when they are in their quiescent state (ie, with no input
signal), therefore no power is dissipated in the output transistors or transformer when there is
no signal present unlike Class A amplifier stages that require significant base bias thereby
dissipating lots of heat – even with no input signal present.
So the overall conversion efficiency ( η ) of the amplifier is greater than that of the equivalent
Class A with efficiencies reaching as high as 70% possible resulting in nearly all modern
types of push-pull amplifiers operated in this Class B mode.
Transformerless Class B Push-Pull Amplifier

One of the main disadvantages of the Class B amplifier circuit above is that it uses balanced
center-tapped transformers in its design, making it expensive to construct. However, there is
another type of Class B amplifier called a Complementary-Symmetry Class B
Amplifier that does not use transformers in its design therefore, it is transformerless using
instead complementary or matching pairs of power transistors.
As transformers are not needed this makes the amplifier circuit much smaller for the same
amount of output, also there are no stray magnetic effects or transformer distortion to effect
the quality of the output signal. An example of a “transformerless” Class B amplifier circuit
is given below.
The Class B amplifier circuit above uses complimentary transistors for each half of the
waveform and while Class B amplifiers have a much high gain than the Class A types, one of
the main disadvantages of class B type push-pull amplifiers is that they suffer from an effect
known commonly as Crossover Distortion.
Hopefully we remember from our tutorials about Transistors that it takes approximately 0.7
volts (measured from base to emitter) to get a bipolar transistor to start conducting. In a pure
class B amplifier, the output transistors are not “pre-biased” to an “ON” state of operation.
This means that the part of the output waveform which falls below this 0.7 volt window will
not be reproduced accurately as the transition between the two transistors (when they are
switching over from one transistor to the other), the transistors do not stop or start conducting
exactly at the zero crossover point even if they are specially matched pairs.
The output transistors for each half of the waveform (positive and negative) will each have a
0.7 volt area in which they are not conducting. The result is that both transistors are turned
“OFF” at exactly the same time.
A simple way to eliminate crossover distortion in a Class B amplifier is to add two small
voltage sources to the circuit to bias both the transistors at a point slightly above their cut-off
point. This then would give us what is commonly called an Class AB Amplifiercircuit.
However, it is impractical to add additional voltage sources to the amplifier circuit so PN-
junctions are used to provide the additional bias in the form of silicon diodes.
Crossover Distortion in Amplifiers

We have seen that one of the main disadvantages of the Class-A Amplifierconfiguration is its low full
power efficiency rating due to being biased around its central Q-point.
In order that there should be no distortion of the output waveform we must

assume that each transistor starts conducting when its base to emitter voltage
rises just above zero, but we know that this is not true because for silicon
bipolar transistors the base voltage must reach at least 0.7v before the
transistor starts to conduct thereby producing this flat spot. This crossover
distortion effect also reduces the overall peak to peak value of the output
waveform causing the maximum power output to be reduced as shown below.
Non-Linear Transfer Characteristics

This effect is less pronounced for large input signals as the input voltage is usually quite large
but for smaller input signals it can be more severe causing audio distortion to the amplifier.
Pre-biasing the Output

The problem of Crossover Distortion can be reduced considerably by applying a slight
forward base bias voltage (same idea as seen in the Transistor tutorial) to the bases of the
two transistors via the center-tap of the input transformer, thus the transistors are no longer
biased at the zero cut-off point but instead are “Pre-biased” at a level determined by this new
biasing voltage.

Complementary Symmetry

Uploaded by

Copyright:

Available Formats

Complementary Symmetry

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Complementary Symmetry

Uploaded by

Copyright:

Available Formats

Push-pull amplifiers use two “complementary” or matching transistors, one being an NPN-

Class B Output Characteristics Curves

Transformerless Class B Push-Pull Amplifier

Crossover Distortion in Amplifiers

In order that there should be no distortion of the output waveform we must

Non-Linear Transfer Characteristics

Pre-biasing the Output

You might also like