Product Guide o e w31

Wärtsilä 31
PRODUCT GUIDE
© Copyright by WÄRTSILÄ FINLAND Oy
All rights reserved. No part of this booklet may be reproduced or copied in any form or by any means (electronic,
mechanical, graphic, photocopying, recording, taping or other information retrieval systems) without the prior written
permission of the copyright owner.
THIS PUBLICATION IS DESIGNED TO PROVIDE AN ACCURATE AND AUTHORITATIVE INFORMATION WITH
REGARD TO THE SUBJECT-MATTER COVERED AS WAS AVAILABLE AT THE TIME OF PRINTING. HOWEVER,THE
PUBLICATION DEALS WITH COMPLICATED TECHNICAL MATTERS SUITED ONLY FOR SPECIALISTS IN THE
AREA, AND THE DESIGN OF THE SUBJECT-PRODUCTS IS SUBJECT TO REGULAR IMPROVEMENTS,
MODIFICATIONS AND CHANGES. CONSEQUENTLY, THE PUBLISHER AND COPYRIGHT OWNER OF THIS
PUBLICATION CAN NOT ACCEPT ANY RESPONSIBILITY OR LIABILITY FOR ANY EVENTUAL ERRORS OR
OMISSIONS IN THIS BOOKLET OR FOR DISCREPANCIES ARISING FROM THE FEATURES OF ANY ACTUAL ITEM
IN THE RESPECTIVE PRODUCT BEING DIFFERENT FROM THOSE SHOWN IN THIS PUBLICATION. THE PUBLISHER
AND COPYRIGHT OWNER SHALL UNDER NO CIRCUMSTANCES BE HELD LIABLE FOR ANY FINANCIAL
CONSEQUENTIAL DAMAGES OR OTHER LOSS, OR ANY OTHER DAMAGE OR INJURY, SUFFERED BY ANY
PARTY MAKING USE OF THIS PUBLICATION OR THE INFORMATION CONTAINED HEREIN.
Wärtsilä 31 Product Guide Introduction
Introduction
This Product Guide provides data and system proposals for the early design phase of marine
engine installations. For contracted projects specific instructions for planning the installation
are always delivered. Any data and information herein is subject to revision without notice.
Issue Published Updates
2/2017 28.09.2017 see CN-A076175
1/2017 10.03.2017 Drawing section updated (Infoboard only). Other updates throughout the
Product Guide.
1/2016 18.10.2016 First version of Product Guide W31
Wärtsilä, Marine Solutions
Vaasa, September 2017
Wärtsilä 31 Product Guide - a3 - 28 September 2017 iii

Wärtsilä 31 Product Guide
Version History
Version Date History
a3 2017-09-28 see CN-A076175
a2 2017-03-10 CN-A063464--/PG-W31
a1 2016-10-18 1/2016
iv Wärtsilä 31 Product Guide - a3 - 28 September 2017

Wärtsilä 31 Product Guide Table of contents
Table of contents
1. Main Data and Outputs ....................................................................................................................... 1-1
1.1 Maximum continuous output ....................................................................................................... 1-1
1.2 Reference conditions ................................................................................................................... 1-2
1.3 Operation in inclined position ..................................................................................................... 1-2
1.4 Dimensions and weights ............................................................................................................. 1-3
2. Operating Ranges ................................................................................................................................ 2-1

2.1 Engine operating range ............................................................................................................... 2-1
2.2 Loading capacity ......................................................................................................................... 2-2
2.3 Operation at low load and idling .................................................................................................. 2-4
2.4 Low air temperature .................................................................................................................... 2-4
3. Technical Data ...................................................................................................................................... 3-1

3.1 Introduction .................................................................................................................................. 3-1
3.2 Wärtsilä 8V31 ............................................................................................................................... 3-2
3.3 Wärtsilä 10V31 ............................................................................................................................. 3-5
3.4 Wärtsilä 12V31 ............................................................................................................................. 3-8
3.5 Wärtsilä 14V31 ............................................................................................................................. 3-11
3.6 Wärtsilä 16V31 ............................................................................................................................. 3-14
4. Description of the Engine .................................................................................................................... 4-1

4.1 Definitions .................................................................................................................................... 4-1
4.2 Main components and systems .................................................................................................. 4-1
4.3 Expected overhaul intervals and life times .................................................................................. 4-5
4.4 Engine storage ............................................................................................................................. 4-5
5. Piping Design, Treatment and Installation ......................................................................................... 5-1

5.1 Pipe dimensions .......................................................................................................................... 5-1
5.2 Trace heating ............................................................................................................................... 5-2
5.3 Pressure class .............................................................................................................................. 5-2
5.4 Pipe class .................................................................................................................................... 5-3
5.5 Insulation ..................................................................................................................................... 5-4
5.6 Local gauges ............................................................................................................................... 5-4
5.7 Cleaning procedures ................................................................................................................... 5-4
5.8 Flexible pipe connections ............................................................................................................ 5-5
5.9 Clamping of pipes ........................................................................................................................ 5-6
6. Fuel Oil System .................................................................................................................................... 6-1

6.1 Acceptable fuel characteristics ................................................................................................... 6-1
6.2 External fuel oil system ................................................................................................................ 6-6
7. Lubricating Oil System ........................................................................................................................ 7-1

7.1 Lubricating oil requirements ........................................................................................................ 7-1
7.2 External lubricating oil system ..................................................................................................... 7-2
7.3 Crankcase ventilation system ..................................................................................................... 7-8
7.4 Flushing instructions .................................................................................................................... 7-10
8. Compressed Air System ...................................................................................................................... 8-1

8.1 Instrument air quality ................................................................................................................... 8-1
8.2 External compressed air system ................................................................................................. 8-1
9. Cooling Water System ......................................................................................................................... 9-1

9.1 Water quality ............................................................................................................................... 9-1
Wärtsilä 31 Product Guide - a3 - 28 September 2017 v

Table of contents Wärtsilä 31 Product Guide
9.2 External cooling water system .................................................................................................... 9-2
10. Combustion Air System ....................................................................................................................... 10-1

10.1 Engine room ventilation ............................................................................................................... 10-1
10.2 Combustion air system design .................................................................................................... 10-3
11. Exhaust Gas System ............................................................................................................................ 11-1

11.1 Exhaust gas outlet ....................................................................................................................... 11-1
11.2 External exhaust gas system ....................................................................................................... 11-3
12. Turbocharger Cleaning ........................................................................................................................ 12-1

12.1 Turbine cleaning system .............................................................................................................. 12-1
12.2 Compressor cleaning system ...................................................................................................... 12-2
13. Exhaust Emissions ............................................................................................................................... 13-1

13.1 Diesel engine exhaust components ............................................................................................ 13-1
13.2 Marine exhaust emissions legislation .......................................................................................... 13-2
13.3 Methods to reduce exhaust emissions ........................................................................................ 13-2
14. Automation System ............................................................................................................................. 14-1

14.1 Technical data and system overview ........................................................................................... 14-1
14.2 Functions .................................................................................................................................... 14-6
14.3 Alarm and monitoring signals ...................................................................................................... 14-8
14.4 Electrical consumers ................................................................................................................... 14-8
14.5 System requirements and guidelines for diesel-electric propulsion ............................................ 14-10
15. Foundation ............................................................................................................................................ 15-1

15.1 Steel structure design .................................................................................................................. 15-1
15.2 Mounting of main engines ........................................................................................................... 15-1
15.3 Mounting of generating sets ........................................................................................................ 15-8
15.4 Flexible pipe connections ............................................................................................................ 15-10
16. Vibration and Noise .............................................................................................................................. 16-1

16.1 External forces and couples ........................................................................................................ 16-1
16.2 Torque variations ......................................................................................................................... 16-2
16.3 Mass moments of inertia ............................................................................................................. 16-2
16.4 Air borne noise ............................................................................................................................. 16-2
16.5 Exhaust noise .............................................................................................................................. 16-3
17. Power Transmission ............................................................................................................................ 17-1

17.1 Flexible coupling .......................................................................................................................... 17-1
17.2 Clutch .......................................................................................................................................... 17-1
17.3 Shaft locking device .................................................................................................................... 17-1
17.4 Input data for torsional vibration calculations ............................................................................. 17-2
17.5 Turning gear ................................................................................................................................. 17-3
18. Engine Room Layout ........................................................................................................................... 18-1

18.1 Crankshaft distances ................................................................................................................... 18-1
18.2 Space requirements for maintenance ......................................................................................... 18-5
18.3 Transportation and storage of spare parts and tools .................................................................. 18-5
18.4 Required deck area for service work ........................................................................................... 18-5
19. Transport Dimensions and Weights ................................................................................................... 19-1

19.1 Lifting of main engines ................................................................................................................ 19-1
19.2 Lifting of generating sets ............................................................................................................. 19-2
19.3 Engine components ..................................................................................................................... 19-3
20. Product Guide Attachments ............................................................................................................... 20-1
vi Wärtsilä 31 Product Guide - a3 - 28 September 2017

Wärtsilä 31 Product Guide Table of contents
21. ANNEX ................................................................................................................................................... 21-1

21.1 Unit conversion tables ................................................................................................................. 21-1
21.2 Collection of drawing symbols used in drawings ........................................................................ 21-2
Wärtsilä 31 Product Guide - a3 - 28 September 2017 vii

This page intentionally left blank
Wärtsilä 31 Product Guide 1. Main Data and Outputs
1. Main Data and Outputs

The Wärtsilä 31 is a 4-stroke, non-reversible, turbocharged and intercooled diesel engine with
direct fuel injection.
Cylinder bore ........................ 310 mm
Stroke ................................... 430 mm
Number of valves ................. 2 inlet valves

2 exhaust valves
Cylinder configuration ......... 8, 10, 12, 14 and 16
V-angle ................................. 50°
Direction of rotation ............. Clockwise, counterclockwise
Speed ................................... 720, 750 rpm
Mean piston speed ............... 10.32 - 10.75 m/s
1.1 Maximum continuous output

Table 1-1 Rating table for Wärtsilä 31
Cylinder Main engines Generating sets

configuration
750 rpm 720 rpm 750 rpm
[kW] Engine [kW] Generator [kVA] Engine [kW] Generator [kVA]
W 8V31 4880 4720 5664 4880 5856
W 10V31 6100 5900 7080 6100 7320
W 12V31 7320 7080 8496 7320 8784
W 14V31 8540 8260 9912 8540 10248
W 16V31 9760 9440 11328 9760 11712
The mean effective pressure Pe can be calculated as follows:
where:
Pe = mean effective pressure [bar]
P = output per cylinder [kW]
n = engine speed [r/min]
D = cylinder diameter [mm]
L = length of piston stroke [mm]
c = operating cycle (4)
Wärtsilä 31 Product Guide - a3 - 28 September 2017 1-1

1. Main Data and Outputs Wärtsilä 31 Product Guide
1.2 Reference conditions

The output is available up to an air temperature of max. 45°C. For higher temperatures, the
output has to be reduced according to the formula stated in ISO 3046-1:2002 (E).
The specific fuel oil consumption is stated in the chapter Technical data. The stated specific
fuel oil consumption applies to engines with engine driven pumps, operating in ambient
conditions according to ISO 15550:2002 (E). The ISO standard reference conditions are:
total barometric pressure 100 kPa
air temperature 25°C
relative humidity 30%
charge air coolant temperature 25°C
Correction factors for the fuel oil consumption in other ambient conditions are given in standard
ISO 3046-1:2002.
1.3 Operation in inclined position

Max. inclination angles at which the engine will operate satisfactorily.
Table 1-2 Inclination with Normal Oil Sump
● Permanent athwart ship inclinations 15°
● Temporary athwart ship inclinations 22.5°
● Permanent fore-and-after inclinations 10°
● Temporary fore-and-after inclinations 10°
NOTE
If inclination exceeds some of the above mentioned angles, a special arrangement
might be needed.
1-2 Wärtsilä 31 Product Guide - a3 - 28 September 2017

1.4 Dimensions and weights

1.4.1 Main engines
Fig 1-1 W8V31 & W10V31 Main engine dimensions (DAAF336230B)
Engine L1 L1* L2 L3 L3* L4 L4* L5 L6 L6*
W8V31 6087 6196 3560 1650 1650 877 986 300 500 500
W10V31 6727 6836 4200 1650 1650 877 986 300 500 500
Engine H1 H1* H2 H3 H4 W1 W1* W2 W3 W4 W5 W5* Weight

ton**
W8V31 3205 3205 4701 1496 650 3115 3115 1600 1153 1585 67 -67 56.7
W10V31 3205 3205 4701 1496 650 3115 3115 1600 1153 1585 67 -67 62

1. Main Data and Outputs Wärtsilä 31 Product Guide
Fig 1-2 W12V31, W14V31 & W16V31 Main engine dimensions (DAAF392671)
Engine L1 L1* L2 L3 L3* L4 L4* L5 L6 L6*
W12V31 7840 8090 4840 2000 2000 1000 1250 300 908 908
W14V31 8480 8730 5480 2000 2000 1000 1250 300 908 908
W16V31 9120 9370 6120 2000 2000 1000 1250 300 908 908
Engine H1 H1* H2 H3 H4 W1 W2 W3 W4 W5 Weight

ton**
W12V31 2926 2926 4633 1496 650 3500 1600 1153 698 1750 72
W14V31 2926 2926 4633 1496 650 3500 1600 1153 698 1750 78.1
W16V31 2926 2926 4633 1496 650 3500 1600 1153 698 1750 86.2
L1 Total length of engine
L2 Length of the engine block
L3 Length from the engine block to the outer most point in turbocharger end
L4 Length from the engine block to the outer most point in non-turbocharger end
L5 Length from engine block to crankshaft flange
L6 Length from engine block to center of exhaust gas outlet
H1 Height from the crankshaft centerline to center of exhaust gas outlet
H2 Total height of engine (normal wet sump)
H3 Height from crankshaft centerline to bottom of the oil sump (normal wet sump)
H4 Height from the crankshaft centerline to engine feet (fixed mounted)
W1 Total width of engine
W2 Width of engine block at the engine feet
W3 Width of oil sump
W4 Width from crankshaft centerline to center of exhaust gas outlet
W5 Width from crankshaft centerline to the outer most point of the engine
* Turbocharger at flywheel end

** Weight with liquids (normal wet sump), but without flywheel

All dimensions in mm.

Wärtsilä 31 Product Guide 2. Operating Ranges
2. Operating Ranges
2.1 Engine operating range

Running below nominal speed the load must be limited according to the diagrams in this
chapter in order to maintain engine operating parameters within acceptable limits. Operation
in the shaded area is permitted only temporarily during transients. Minimum speed is indicated
in the diagram, but project specific limitations may apply.
2.1.1 Controllable pitch propellers

The engine load must be limited according to the diagram below when operating below nominal
speed, in order to maintain engine operating parameters within acceptable limits. Operation
in the shaded area is permitted only temporarily during transients to permit smooth overload
control.
Note that project specific vibration calculations may result in higher minimum speed than in
the diagram below.
The propulsion control must also include automatic limitation of the load increase rate.
Maximum loading rates can be found later in this chapter.
The propeller efficiency is highest at design pitch. It is common practice to dimension the
propeller so that the specified ship speed is attained with design pitch, nominal engine speed
and 85% output in the specified loading condition. The power demand from a possible shaft
generator or PTO must be taken into account. The 15% margin is a provision for weather
conditions and fouling of hull and propeller. An additional engine margin can be applied for
most economical operation of the engine, or to have reserve power.
Fig 2-1 Operating field for CP Propeller

2. Operating Ranges Wärtsilä 31 Product Guide
2.2 Loading capacity

Controlled load increase is essential for highly supercharged diesel engines, because the
turbocharger needs time to accelerate before it can deliver the required amount of air. A slower
loading ramp than the maximum capability of the engine permits a more even temperature
distribution in engine components during transients.
The engine can be loaded immediately after start, provided that the engine is pre-heated to
a HT-water temperature of min 70ºC, and the lubricating oil temperature is min. 40 ºC.
The ramp for normal loading applies to engines that have reached normal operating
temperature.
2.2.1 Mechanical propulsion
Fig 2-2 Maximum recommended load increase rates for variable speed engines
The propulsion control must include automatic limitation of the load increase rate. If the control
system has only one load increase ramp, then the ramp for a preheated engine should be
used. In tug applications the engines have usually reached normal operating temperature
before the tug starts assisting. The “emergency” curve is close to the maximum capability of
the engine.
Large load reductions from high load should also be performed gradually. In normal operation
the load should not be reduced from 100% to 0% in less than 15 seconds. When absolutely
necessary, the load can be reduced as fast as the pitch setting system can react (overspeed
due to windmilling must be considered for high speed ships).

Wärtsilä 31 Product Guide 2. Operating Ranges
2.2.2 Diesel electric propulsion and auxiliary engines
Fig 2-3 Maximum recommended load increase rates for engines operating at
nominal speed
In diesel electric installations loading ramps are implemented both in the propulsion control
and in the power management system, or in the engine speed control in case isochronous
load sharing is applied. If a ramp without knee-point is used, it should not achieve 100% load
in shorter time than the ramp in the figure. When the load sharing is based on speed droop,
the load increase rate of a recently connected generator is the sum of the load transfer
performed by the power management system and the load increase performed by the
propulsion control.
The “emergency” curve is close to the maximum capability of the engine and it shall not be
used as the normal limit. In dynamic positioning applications loading ramps corresponding to
20-30 seconds from zero to full load are however normal. If the vessel has also other operating
modes, a slower loading ramp is recommended for these operating modes.
In typical auxiliary engine applications there is usually no single consumer being decisive for
the loading rate. It is recommended to group electrical equipment so that the load is increased
in small increments, and the resulting loading rate roughly corresponds to the “normal” curve.
In normal operation the load should not be reduced from 100% to 0% in less than 15 seconds.
If the application requires frequent unloading at a significantly faster rate, special arrangements
can be necessary on the engine. In an emergency situation the full load can be thrown off
instantly.
2.2.2.1 Maximum instant load steps

The electrical system must be designed so that tripping of breakers can be safely handled.
This requires that the engines are protected from load steps exceeding their maximum load
acceptance capability. The load steps are in three equal steps. The resulting speed drop is
less than 10% and the recovery time to within 1% of the steady state speed at the new load
level is max. 5 seconds.
When electrical power is restored after a black-out, consumers are reconnected in groups,
which may cause significant load steps. The engine must be allowed to recover for at least
10 seconds before applying the following load step, if the load is applied in maximum steps.
2.2.2.2 Start-up time

A diesel generator typically reaches nominal speed in about 20 seconds after the start signal.
The acceleration is limited by the speed control to minimise smoke during start-up. If requested
faster starting times can be arranged.

2. Operating Ranges Wärtsilä 31 Product Guide
2.3 Operation at low load and idling

Table 2-1 Idling and low load operation restrictions
Load LFO, max continous HFO, max continous

time [h] time [h]
0% 15 10
2% 50 10
17.5% 300 200
Fig 2-4 Low load operating restrictions
NOTE
1) Above 17.5% load there is no additional restriction from low load operation.
2) Duration of low load only applies if charge air temp in receiver is at:
- LFO: 35C or above
- HFO: 45C or above
3) High load running (minimum 70%) is to be followed for a minimum of 60 minutes to clean up the engine
after maximum allowed low load running time has been reached.
2.4 Low air temperature

In cold conditions the following minimum inlet air temperatures apply:
● Min 5ºC
For lower suction air temperatures engines shall be configured for arctic operation.
For further guidelines, see chapter Combustion air system design.

Wärtsilä 31 Product Guide 3. Technical Data
3. Technical Data
3.1 Introduction
This chapter contains technical data of the engine (heat balance, flows, pressures etc.) for
design of auxiliary systems. Further design criteria for external equipment and system layouts
are presented in the respective chapter.
3.1.1 Engine driven pumps

The fuel consumption stated in the technical data tables is with engine driven pumps. The
increase in fuel consumption with engine driven pumps is given in the table below; correction
in g/kWh.
Table 3-1 Constant speed engines
Engine driven Engine load [%]

pumps
100 85 75 50
Lube oil -1.1 -1.2 -1.4 -2.3
LT Water -0.5 -0.5 -0.6 -1.0
HT Water -0.5 -0.5 -0.6 -1.0
Table 3-2 Variable speed engines
Engine driven Engine load [%]

pumps
100 85 75 50
Lube oil -1.2 -1.4 -1.5 -2.0
LT Water -0.5 -0.5 -0.5 -0.5
HT Water -0.5 -0.5 -0.5 -0.5

3. Technical Data Wärtsilä 31 Product Guide
3.2 Wärtsilä 8V31

DE DE AUX AUX ME
Wärtsilä 8V31
IMO Tier 2 IMO Tier 2 IMO Tier 2 IMO Tier 2 IMO Tier 2
Engine speed RPM 720 750 720 750 750

Cylinder output kW/cyl 590 610 590 610 610
Speed mode Constant Constant Constant Constant Variable
Engine output kW 4720 4880 4720 4880 4880
Mean effective pressure MPa 3.03 3.01 3.03 3.01 3.01
Combustion air system (Note 1)
Flow at 100% load kg/s 8.32 8.63 8.32 8.63 8.63
Temperature at turbocharger intake, max. °C 45 45 45 45 45
Air temperature after air cooler (TE 601) °C 60 60 60 60 60
Exhaust gas system (Note 2)
Flow at 100% load kg/s 8.56 8.88 8.56 8.88 8.88
Flow at 85% load kg/s 7.28 7.6 7.28 7.6 7.52
Flow at 75% load kg/s 6.56 6.8 6.56 6.8 6.48
Flow at 50% load kg/s 4.96 5.2 4.96 5.2 4.56
Temperature after turbocharger, 100% load (TE 517) °C 275 273 275 273 273
Backpressure, max. kPa 5.0 5.0 5.0 5.0 5.0
Calculated pipe diameter for 35m/s mm 693 705 693 705 705
Heat balance (Note 3)
Jacket water, HT-circuit kW 460 494 460 494 494
Charge air, HT-circuit kW 858 926 858 926 926
Charge air, LT-circuit kW 1195 1230 1195 1230 1230
Lubricating oil, LT-circuit kW 487 522 487 522 522
Radiation kW 131 137 131 137 137
For optional engineversions heat balances may differ
Fuel system (Note 4)
Pressure before injection pumps (PT 101) kPa 1000±100 1000±100 1000±100 1000±100 1000±100
Engine driven pump capacity (MDF only) m3/h 3.6 3.6 3.6 3.6 3.6
HFO viscosity before engine cSt 16...24 16...24 16...24 16...24 16...24
HFO temperature before engine, max. (TE 101) °C 140 140 140 140 140
MDF viscosity, min cSt 2.0 2.0 2.0 2.0 2.0
MDF temperature before engine, max. (TE 101) °C 45 45 45 45 45
Fuel consumption at 100% load, HFO g/kWh 173.4 174.4 173.9 174.9 174.4
Fuel consumption at 100% load, MDF g/kWh 172.5 173.4 173.0 173.9 173.4

DE DE AUX AUX ME
Wärtsilä 8V31
Engine speed RPM 720 750 720 750 750

Clean leak fuel quantity, MDF at 100% load kg/h 5.1 5.1 5.1 5.1 5.1
Clean leak fuel quantity, HFO at 100% load kg/h 0.5 0.5 0.5 0.5 0.5
Lubricating oil system
Pressure before bearings, nom. (PT 201) kPa 420 420 420 420 420
Suction ability main pump, including pipe loss, max. kPa 40 40 40 40 40
Priming pressure, nom. (PT 201) kPa 100 100 100 100 100
Suction ability priming pump, including pipe loss, max. kPa 35 35 35 35 35
Temperature before bearings, nom. (TE 201) °C 70 70 70 70 70
Temperature after engine, approx. °C 82 82 82 82 82
Pump capacity (main), engine driven m³/h 125 130 125 130 144
Pump capacity (main), stand-by m³/h 100 100 100 100 100
Priming pump capacity, 50Hz/60Hz m³/h 20.0 / 20.0 20.0 / 20.0 20.0 / 20.0 20.0 / 20.0 20.0 / 20.0
Oil volume, wet sump, nom. m³ 2.54 2.54 2.54 2.54 2.54
Oil volume in separate system oil tank, nom. m³ 6.4 6.6 6.4 6.6 6.6
Oil consumption (100% load), approx. g/kWh 0.45 0.45 0.45 0.45 0.45
Crankcase ventilation flow rate at full load l/min 1960 1960 1960 1960 1960
Crankcase ventilation backpressure, max. kPa 0.1 0.1 0.1 0.1 0.1
Oil volume in turning device liters 6.0...6.8 6.0...6.8 6.0...6.8 6.0...6.8 6.0...6.8
Cooling water system
High temperature cooling water system
Pressure at engine, after pump, nom. (PT 401) kPa 358 + stat- 358 + stat- 358 + stat- 358 + stat- 358 + stat-
ic ic ic ic ic
Pressure at engine, after pump, max. (PT 401) kPa 600 600 600 600 600
Temperature before cylinders, approx. (TE 401) °C 83 83 83 83 83
HT-water out from engine, nom (TE432) °C 96 96 96 96 96
Capacity of engine driven pump, nom. m³/h 80 80 80 80 80
Pressure drop over engine, total kPa 210 210 210 210 210
Pressure drop in external system, max. kPa 100 100 100 100 100
Pressure from expansion tank kPa 70...150 70...150 70...150 70...150 70...150
Water volume in engine m³ 0.603 0.603 0.603 0.603 0.603
Low temperature cooling water system
Temperature before engine (TE 451) °C 40 ... 45 40 ... 45 40 ... 45 40 ... 45 40 ... 45
Pressure drop over charge air cooler (one-stage) kPa 41 41 41 41 41
Pressure drop over charge air cooler (two-stage) kPa 110 110 110 110 110

DE DE AUX AUX ME
Wärtsilä 8V31
Engine speed RPM 720 750 720 750 750

Pressure drop over oil cooler kPa 115 115 115 115 115
Pressure from expansion tank kPa 70 ... 150 70 ... 150 70 ... 150 70 ... 150 70 ... 150
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000
Pressure at engine during start, min. (20°C) kPa 1500 1500 1500 1500 1500
Pressure, max. kPa 3000 3000 3000 3000 3000
Low pressure limit in air vessels kPa 1600 1600 1600 1600 1600
Air consumption per start Nm3 4.9 4.9 4.9 4.9 4.9
Notes:
Note 1 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C) and 100% load. Flow tolerance 9%.
Note 2 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C). Flow tolerance 9% and temperature tolerance
15°C.
Note 3 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C) and 100% load. Tolerance for cooling water heat
10%, tolerance for radiation heat 18%. Fouling factors and a margin to be taken into account when dimensioning heat
exchangers. In arctic option all charge air coolers are in LT circuit.
Note 4 At ambient conditions according to ISO 15550. Lower calorific value 42 700 kJ/kg. With engine driven pumps (two cooling
water + one lubricating oil pump). Tolerance 5%.
ME = Engine driving propeller, variable speed

AE = Auxiliary engine driving generator
DE = Diesel-Electric engine driving generator
Subject to revision without notice.

3.3 Wärtsilä 10V31

DE DE AUX AUX ME
Wärtsilä 10V31
Engine speed RPM 720 750 720 750 750

Engine output kW 5900 6100 5900 6100 6100
Flow at 100% load kg/s 10.41 10.79 10.41 10.79 10.79
Flow at 100% load kg/s 10.7 11.1 10.7 11.1 11.1
Flow at 85% load kg/s 9.1 9.5 9.1 9.5 9.4
Flow at 75% load kg/s 8.2 8.5 8.2 8.5 8.1
Flow at 50% load kg/s 6.2 6.5 6.2 6.5 5.7
Radiation kW 164 171 164 171 171

DE DE AUX AUX ME
Wärtsilä 10V31
Engine speed RPM 720 750 720 750 750

ic ic ic ic ic
Water volume in engine m³ 0.642 0.642 0.642 0.642 0.642
Pressure drop over charge air cooler kPa 0 0 0 0 0

DE DE AUX AUX ME
Wärtsilä 10V31
Engine speed RPM 720 750 720 750 750

Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000
Notes:
15°C.



DE DE AUX AUX ME
Wärtsilä 12V31
Engine speed RPM 720 750 720 750 750

Engine output kW 7080 7320 7080 7320 7320
Flow at 100% load kg/s 12.49 12.95 12.49 12.95 12.95
Flow at 100% load kg/s 12.84 13.32 12.84 13.32 13.32
Flow at 85% load kg/s 10.92 11.4 10.92 11.4 11.28
Flow at 75% load kg/s 9.84 10.2 9.84 10.2 9.72
Flow at 50% load kg/s 7.44 7.8 7.44 7.8 6.84
Radiation kW 197 205 197 205 205
For optional engine versions heat balances may differ

DE DE AUX AUX ME
Wärtsilä 12V31
Engine speed RPM 720 750 720 750 750

ic ic ic ic ic
Water volume in engine m³

DE DE AUX AUX ME
Wärtsilä 12V31
Engine speed RPM 720 750 720 750 750

Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000
Notes:
15°C.



DE DE AUX AUX ME
Wärtsilä 14V31
Engine speed RPM 720 750 720 750 750

Engine output kW 8260 8540 8260 8540 8540
Flow at 100% load kg/s 14.57 15.11 14.57 15.11 15.11
Flow at 100% load kg/s 14.98 15.54 14.98 15.54 15.54
Flow at 85% load kg/s 12.74 13.3 12.74 13.3 13.16
Flow at 75% load kg/s 11.48 11.9 11.48 11.9 11.34
Flow at 50% load kg/s 8.68 9.1 8.68 9.1 7.98
Radiation kW 230 239 230 239 239

DE DE AUX AUX ME
Wärtsilä 14V31
Engine speed RPM 720 750 720 750 750

ic ic ic ic ic

DE DE AUX AUX ME
Wärtsilä 14V31
Engine speed RPM 720 750 720 750 750

Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000
Notes:
15°C.



DE DE AUX AUX ME
Wärtsilä 16V31
Engine speed RPM 720 750 720 750 750

Engine output kW 9440 9760 9440 9760 9760
Flow at 100% load kg/s 16.65 17.27 16.65 17.27 17.27
Flow at 100% load kg/s 17.12 17.76 17.12 17.76 17.76
Flow at 85% load kg/s 14.56 15.2 14.56 15.2 15.04
Flow at 75% load kg/s 13.12 13.6 13.12 13.6 12.96
Flow at 50% load kg/s 9.92 10.4 9.92 10.4 9.12
Radiation kW 262 274 262 274 274

DE DE AUX AUX ME
Wärtsilä 16V31
Engine speed RPM 720 750 720 750 750

ic ic ic ic ic

DE DE AUX AUX ME
Wärtsilä 16V31
Engine speed RPM 720 750 720 750 750

Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000
Notes:
15°C.


Wärtsilä 31 Product Guide 4. Description of the Engine
4. Description of the Engine
4.1 Definitions
Fig 4-1 Engine definitions (V93C0028)
4.2 Main components and systems

4.2.1 Engine block
The engine block, made of nodular cast iron, is cast in one piece for all cylinder numbers and
it supports the underslung crankshaft. The block has been given a stiff and durable design to
absorb internal forces and the engine can therefore also be resiliently mounted not requiring
any intermediate foundations. It incorporates water and charge air main and side channels.
Also camshaft bearing housings are incorporated in the engine block. The engines are equipped
with crankcase explosion relief valve with flame arrester.
The main bearing caps, made of nodular cast iron, are fixed with two hydraulically tensioned
screws from below. They are guided sideways and vertically by the engine block. Hydraulically
tensioned horizontal side screws at the lower guiding provide a very rigid crankshaft bearing
assembly.
A hydraulic jack, supported in the oil sump, offers the possibility to lower and lift the main
bearing caps, e.g. when inspecting the bearings. Lubricating oil is led to the bearings through
this jack.
The oil sump, a light welded design, is mounted on the engine block from below. The oil sump
is available in two alternative designs, wet or dry sump, depending on the type of application.
The wet oil sump includes a suction pipe to the lubricating oil pump. For wet sump there is a
main distributing pipe for lubricating oil, suction pipes and return connections for the separator.
For the dry sump there is a main distributing oil pipe for lubricating oil and drains at either end
to a separate system oil tank.
The engine holding down bolts are hydraulically tightened in order to facilitate the engine
installation to both rigid and resilient foundation.
4.2.2 Crankshaft
Crankshaft line is built up from several pieces: crankshaft, counter weights, split camshaft
gear wheel and pumpdrive arrangement.

4. Description of the Engine Wärtsilä 31 Product Guide
Crankshaft itself is forged in one piece. Both main bearings and big end bearings temperatures
are continuously monitored.
Counterweights are fitted on every web. High degree of balancing results in an even and thick
oil film for all bearings.
The connecting rods are arranged side-by-side and the diameters of the crank pins and journals
are equal irrespective of the cylinder number.
All crankshafts can be provided with torsional vibration dampers or tuning masses at the free
end of the engine, if necessary. Main features of crankshaft design: clean steel technology
minimizes the amount of slag forming elements and guarantees superior material durability.
The crankshaft alignment is always done on a thoroughly warm engine after the engine is
stopped.
4.2.3 Connecting rod

The connecting rod is of forged alloy steel. All connecting rod studs are hydraulically tightened.
The connecting rod is of a three-piece design, which gives a minimum dismantling height and
enables the piston to be dismounted without opening the big end bearing.
4.2.4 Main bearings and big end bearings

The main bearings and the big end bearings are of tri-metal design with steel back, lead-bronze
lining and a soft running layer. The bearings are covered with a Sn-flash for corrosion protection.
Even minor form deviations can become visible on the bearing surface in the running in phase.
This has no negative influence on the bearing function. A wireless system for real-time
temperature monitoring of connecting rod big end bearings, "BEB monitoring system", is as
standard.
4.2.5 Cylinder liner

The cylinder liners are centrifugally cast of a special alloyed cast iron. The top collar of the
cylinder liner is provided with a water jacket for distributing cooling water through the cylinder
liner cooling bores. This will give an efficient control of the liner temperature. An oil lubrication
system inside the cylinder liner lubricates the gudgeon pin bearing and also cools piston crown
through the oil channels underside of the piston.
4.2.6 Piston
The piston is of composite type with steel crown and nodular cast iron skirt. A piston skirt
lubricating system, featuring oil bores in a groove on the piston skirt, lubricates the piston
skirt/cylinder liner. The piston top is oil cooled by the same system mentioned above. The
piston ring grooves are hardened for extended lifetime.
4.2.7 Piston rings

The piston ring set are located in the piston crown and consists of two directional compression
rings and one spring-loaded conformable oil scraper ring. Running face of compression rings
are chromium-ceramic-plated.
4.2.8 Cylinder head

The cross flow cylinder head is made of cast iron. The mechanical load is absorbed by a flame
plate, which together with the upper deck and the side walls form a rigid box section. There
are four hydraulically tightened cylinder head bolts. The exhaust valve seats and the flame
deck are efficiently and direct water-cooled. The valve seat rings are made of alloyed steel,
for wear resistance. All valves are hydraulic controlled with valve guides and equipped with
valve springs and rotators.

A small side air receiver is located in the hot box, including charge air bends with integrated
hydraulics and charge air riser pipes.
Following components are connected to the cylinder head:
● Charge air components for side receiver
● Exhaust gas pipe to exhaust system
● Cooling water collar
● Quill pipe with High Pressure (HP) fuel pipe connections
4.2.9 Camshaft and valve mechanism

The cams are integrated in the drop forged shaft material. The bearing journals are made in
separate pieces, which are fitted, to the camshaft pieces by flange connections. The camshaft
bearing housings are integrated in the engine block casting and are thus completely closed.
The bearings are installed and removed by means of a hydraulic tool. The camshaft covers,
one for each cylinder, seal against the engine block with a closed O-ring profile. The valve
tappets are of piston type with self-adjustment of roller against cam to give an even distribution
of the contact pressure. Inlet and exhaust valves have a special steam coating and hard facing
on the seat surface, for long lifetime. The valve springs make the valve mechanism dynamically
stable.
The step-less valve mechanism makes it possible to control the timing of both inlet & exhaust
valves. It allows to always use a proper scavenging period. This is needed to optimize and
balance emissions, fuel consumption, operational flexibility & load taking, whilst maintaining
thermal and mechanical reliability. The design enables clearly longer maintenance interval,
due to the reduced thermal and mechanical stress on most of the components in the valve
mechanism.
4.2.10 Camshaft drive

The camshafts are driven by the crankshaft through a gear train.
4.2.11 Turbocharging and charge air cooling

The selected 2-stage turbocharging offers ideal combination of high-pressure ratios and good
efficiency both at full and part load. The turbochargers can be placed at the free end or fly
wheel end of the engine. For cleaning of the turbochargers during operation there is, as
standard, a water washing device for the air (compressor) and exhaust gas (turbine) side of
the LP stage and for the exhaust gas (turbine) side of the HP stage. The water washing device
is to be connected to an external unit. The turbochargers are lubricated by engine lubricating
oil with integrated connections.
An Exhaust gas Waste Gate (EWG) system controls the exhaust gas flow by-passing for both
high pressure (HP) and low pressure (LP) turbine stages. EWG is needed also in case of engines
equipped with exhaust gas after treatment based on Selective Catalytic Reaction (SCR).
By using Air Waste Gate (AWG) the charge air pressure and the margin from LP compressor
is controlled.
A step-less Air By-pass valve (ABP) system is used in all engine applications for preventing
surging of turbocharger compressors in case of rapid engine load reduction.
The Charge Air Coolers (CAC) consist of a 2-stage type cooler (LP CAC) between the LP and
HP compressor stages and a 1-stage cooler (HP CAC) between the HP compressor stage
and the charge air receiver. The LP CAC is cooled with LT-water or in some cases by both
HT- and LT-water. The HP CAC is always cooled by LT-water and fresh water is used for both
circuits. When there is a risk for over-speeding of the engine due to presence of combustible
gas or vapour in the inlet air, a UNIC automation controlled Charge Air Blocking device, can
be installed.
See chapter Exhaust gas & charge air systems for more information.

4. Description of the Engine Wärtsilä 31 Product Guide
4.2.12 Fuel injection equipment

The fuel injection equipment and system piping are located in a hotbox, providing maximum
reliability and safety when using preheated heavy fuels. In the Wärtsilä electronic fuel injection
system, the fuel is pressurized in the high pressure HP-pumps from where the fuel is fed to
the injection valves which are rate optimized. The fuel system consists of different numbers
of fuel oil HP pumps, depending of the cylinder configuration. HP pumps are located at the
engine pump cover and from there high pressure pipes are connected to the system piping.
A valve block is mounted at the fuel outlet pipe, including Pressure Drop and Safety Valve
(PDSV), Circulation Valve (CV) and a fuel pressure discharge volume. The PDSV acts as
mechanical safety valve and the fuel volume lowers the system pressure. The injection valves
are electronic controlled and the injection timing is pre-set in the control system software.
4.2.13 Lubricating oil system

The engine internal lubricating oil system include the engine driven lubricating oil pump, the
electrically driven prelubricating oil pump, thermostatic valve, filters and lubricating oil cooler.
The lubricating oil pumps are located in the free end of the engine, while the automatic filter,
cooler and thermostatic valve are integrated into one module.
4.2.14 Cooling water system

The fresh water cooling system is divided into a high temperature (HT) and a low temperature
(LT) circuit.
For engines operating in normal conditions the HT-water is cooling the cylinders (jacket) and
the first stage of the low pressure 2-stage charge air cooler. The LT-water is cooling the
lubricating oil cooler, the second stage of the low pressure 2-stage charge air cooler and the
high pressure 1-stage charge air cooler.
For engines operating in cold conditions the HT-water is cooling the cylinders (Jacket). A
HT-water pump is circulating the cooling water in the circuit and a thermostatic valve mounted
in the internal cooling water system, controls the outlet temperature of the circuit. The LT-circuit
is cooling the Lubricating Oil Cooler (LOC), the second stage of the Low Pressure 2-stage
charge air cooler, the High Pressure 1-stage charge air cooler and the first stage of the low
pressure 2-stage charge air cooler. An LT-thermostatic valve mounted in the external cooling
water system, controls the inlet temperature to the engine for achieving correct receiver
temperature.
4.2.15 Exhaust pipes

The exhaust manifold pipes are made of special heat resistant nodular cast iron alloy.
The complete exhaust gas system is enclosed in an insulating box consisting of easily
removable panels. Mineral wool is used as insulating material.
4.2.16 Automation system

The Wärtsilä 31 engine is equipped with an UNIC electronic control system. UNIC have
hardwired interface for control functions and a bus communication interface for alarm and
monitoring. Additionally UNIC includes fuel injection control for engines with electronic fuel
injection rate optimized nozzles.
For more information, see chapter Automation system.

4.3 Expected overhaul intervals and life times

Time between inspection or overhaul and expected life times for the most important
components of the Wärtsilä 31A engines are:
4.3.1 Time Between Overhaul and Expected Life Time

The following overhaul intervals and lifetimes are for guidance only. Actual figures will be
different depending on service conditions. Expected component lifetimes have been adjusted
to match overhaul intervals.
Table 4-1 Time Between Overhaul and Expected Life Time
Component Time between inspection or overhaul Expected life time (h) 1)

(h)
HFO LFO HFO LFO
Piston 24000 32000 Min. 72000 Min. 96000
Piston rings 24000 32000 24000 32000
Cylinder liner 24000 32000 96000 128000
Cylinder head 24000 32000 96000 128000
Inlet valve 24000 32000 24000 32000
Exhaust valve 24000 32000 24000 32000
Main bearing 24000 32000 48000 64000
Big end bearing 24000 32000 24000 32000
Intermediate gear 64000 64000 64000 64000

bearings
Balancing shaft 32000 32000 32000 32000
bearings
Injection valve 8000 8000 NA NA
(wear parts)
High Pressure fuel 24000 24000 24000 24000
pump
LP and the HP tur- 16000 16000 64000 64000
bochargers
NOTE
1) Achieved life times very much depend on the operating conditions, average
loading of the engine, fuel quality used, fuel handling systems, performance of
maintenance etc.
NOTE
Please refer to Fuel Characteristics DAAF290773 for HFO and LFO specification.
4.4 Engine storage

At delivery the engine is provided with VCI coating and a tarpaulin. For storage longer than 3
months please contact Wärtsilä Finland Oy.

Wärtsilä 31 Product Guide 5. Piping Design, Treatment and Installation
5. Piping Design, Treatment and Installation

This chapter provides general guidelines for the design, construction and planning of piping
systems, however, not excluding other solutions of at least equal standard. Installation related
instructions are included in the project specific instructions delivered for each installation.
Fuel, lubricating oil, fresh water and compressed air piping is usually made in seamless carbon
steel (DIN 2448) and seamless precision tubes in carbon or stainless steel (DIN 2391), exhaust
gas piping in welded pipes of corten or carbon steel (DIN 2458). Sea-water piping should be
in Cunifer or hot dip galvanized steel.
NOTE
The pipes in the freshwater side of the cooling water system must not be galvanized!
Attention must be paid to fire risk aspects. Fuel supply and return lines shall be designed so
that they can be fitted without tension. Flexible hoses must have an approval from the
classification society. If flexible hoses are used in the compressed air system, a purge valve
shall be fitted in front of the hose(s).
It is recommended to make a fitting order plan prior to construction.
The following aspects shall be taken into consideration:
● Pockets shall be avoided. When not possible, drain plugs and air vents shall be installed
● Leak fuel drain pipes shall have continuous slope
● Vent pipes shall be continuously rising
● Flanged connections shall be used, cutting ring joints for precision tubes
Maintenance access and dismounting space of valves, coolers and other devices shall be
taken into consideration. Flange connections and other joints shall be located so that
dismounting of the equipment can be made with reasonable effort.
5.1 Pipe dimensions

When selecting the pipe dimensions, take into account:
● The pipe material and its resistance to corrosion/erosion.
● Allowed pressure loss in the circuit vs delivery head of the pump.
● Required net positive suction head (NPSH) for pumps (suction lines).
● In small pipe sizes the max acceptable velocity is usually somewhat lower than in large
pipes of equal length.
● The flow velocity should not be below 1 m/s in sea water piping due to increased risk of
fouling and pitting.
● In open circuits the velocity in the suction pipe is typically about 2/3 of the velocity in the
delivery pipe.

5. Piping Design, Treatment and Installation Wärtsilä 31 Product Guide
Table 5-1 Recommended maximum velocities on pump delivery side for guidance
Piping Pipe material Max velocity [m/s]
Fuel oil piping (MDF and HFO) Black steel 1.0
Lubricating oil piping Black steel 1.5
Fresh water piping Black steel 2.5
Sea water piping Galvanized steel 2.5
Aluminum brass 2.5
10/90 copper-nickel-iron 3.0
70/30 copper-nickel 4.5
Rubber lined pipes 4.5
NOTE
The diameter of gas fuel piping depends only on the allowed pressure loss in the
piping, which has to be calculated project specifically.
Compressed air pipe sizing has to be calculated project specifically. The pipe sizes may be
chosen on the basis of air velocity or pressure drop. In each pipeline case it is advised to
check the pipe sizes using both methods, this to ensure that the alternative limits are not being
exceeded.
Pipeline sizing on air velocity: For dry air, practical experience shows that reasonable
velocities are 25...30 m/s, but these should be regarded as the maximum above which noise
and erosion will take place, particularly if air is not dry. Even these velocities can be high in
terms of their effect on pressure drop. In longer supply lines, it is often necessary to restrict
velocities to 15 m/s to limit the pressure drop.
Pipeline sizing on pressure drop: As a rule of thumb the pressure drop from the starting air
vessel to the inlet of the engine should be max. 0.1 MPa (1 bar) when the bottle pressure is 3
MPa (30 bar).
It is essential that the instrument air pressure, feeding to some critical control instrumentation,
is not allowed to fall below the nominal pressure stated in chapter "Compressed air system"
due to pressure drop in the pipeline.
5.2 Trace heating

The following pipes shall be equipped with trace heating (steam, thermal oil or electrical). It
shall be possible to shut off the trace heating.
● All heavy fuel pipes
● All leak fuel and filter flushing pipes carrying heavy fuel
5.3 Pressure class

The pressure class of the piping should be higher than or equal to the design pressure, which
should be higher than or equal to the highest operating (working) pressure. The highest
operating (working) pressure is equal to the setting of the safety valve in a system.
The pressure in the system can:
● Originate from a positive displacement pump

● Be a combination of the static pressure and the pressure on the highest point of the pump
curve for a centrifugal pump
● Rise in an isolated system if the liquid is heated
Within this publication there are tables attached to drawings, which specify pressure classes
of connections. The pressure class of a connection can be higher than the pressure class
required for the pipe.
Example 1:
The fuel pressure before the engine should be 0.7 MPa (7 bar). The safety filter in dirty condition
may cause a pressure loss of 0.1 MPa (1.0 bar). The viscosimeter, automatic filter, preheater
and piping may cause a pressure loss of 0.25 MPa (2.5 bar). Consequently the discharge
pressure of the circulating pumps may rise to 1.05 MPa (10.5 bar), and the safety valve of the
pump shall thus be adjusted e.g. to 1.2 MPa (12 bar).
● A design pressure of not less than 1.2 MPa (12 bar) has to be selected.
● The nearest pipe class to be selected is PN16.
● Piping test pressure is normally 1.5 x the design pressure = 1.8 MPa (18 bar).
Example 2:
The pressure on the suction side of the cooling water pump is 0.1 MPa (1 bar). The delivery
head of the pump is 0.3 MPa (3 bar), leading to a discharge pressure of 0.4 MPa (4 bar). The
highest point of the pump curve (at or near zero flow) is 0.1 MPa (1 bar) higher than the nominal
point, and consequently the discharge pressure may rise to 0.5 MPa (5 bar) (with closed or
throttled valves).
● Consequently a design pressure of not less than 0.5 MPa (5 bar) shall be selected.
● The nearest pipe class to be selected is PN6.
● Piping test pressure is normally 1.5 x the design pressure = 0.75 MPa (7.5 bar).
Standard pressure classes are PN4, PN6, PN10, PN16, PN25, PN40, etc.
5.4 Pipe class

Classification societies categorize piping systems in different classes (DNV) or groups (ABS)
depending on pressure, temperature and media. The pipe class can determine:
● Type of connections to be used
● Heat treatment
● Welding procedure
● Test method
Systems with high design pressures and temperatures and hazardous media belong to class
I (or group I), others to II or III as applicable. Quality requirements are highest on class I.
Examples of classes of piping systems as per DNV rules are presented in the table below.
Table 5-2 Classes of piping systems as per DNV rules
Media Class I Class II Class III
MPa (bar) °C MPa (bar) °C MPa (bar) °C
Steam > 1.6 (16) or > 300 < 1.6 (16) and < 300 < 0.7 (7) and < 170
Flammable fluid > 1.6 (16) or > 150 < 1.6 (16) and < 150 < 0.7 (7) and < 60
Other media > 4 (40) or > 300 < 4 (40) and < 300 < 1.6 (16) and < 200

5.5 Insulation
The following pipes shall be insulated:
● All trace heated pipes
● Exhaust gas pipes
● Exposed parts of pipes with temperature > 60°C
Insulation is also recommended for:
● Pipes between engine or system oil tank and lubricating oil separator
● Pipes between engine and jacket water preheater
5.6 Local gauges

Local thermometers should be installed wherever a new temperature occurs, i.e. before and
after heat exchangers, etc.
Pressure gauges should be installed on the suction and discharge side of each pump.
5.7 Cleaning procedures

Instructions shall be given at an early stage to manufacturers and fitters how different piping
systems shall be treated, cleaned and protected.
5.7.1 Cleanliness during pipe installation

All piping must be verified to be clean before lifting it onboard for installation. During the
construction time uncompleted piping systems shall be maintained clean. Open pipe ends
should be temporarily closed. Possible debris shall be removed with a suitable method. All
tanks must be inspected and found clean before filling up with fuel, oil or water.
Piping cleaning methods are summarised in table below:
Table 5-3 Pipe cleaning
System Methods
Fuel oil A,B,C,D,F
Lubricating oil A,B,C,D,F
Starting air A,B,C
Cooling water A,B,C
Exhaust gas A,B,C
Charge air A,B,C
1) In case of carbon steel pipes
Methods applied during prefabrication of pipe spools
A = Washing with alkaline solution in hot water at 80°C for degreasing (only if pipes have been greased)
B = Removal of rust and scale with steel brush (not required for seamless precision tubes)
D = Pickling (not required for seamless precision tubes)
Methods applied after installation onboard

C = Purging with compressed air
F = Flushing
5.7.2 Pickling
Prefabricated pipe spools are pickled before installation onboard.
Pipes are pickled in an acid solution of 10% hydrochloric acid and 10% formaline inhibitor for
4-5 hours, rinsed with hot water and blown dry with compressed air.
After acid treatment the pipes are treated with a neutralizing solution of 10% caustic soda
and 50 grams of trisodiumphosphate per litre of water for 20 minutes at 40...50°C, rinsed with
hot water and blown dry with compressed air.
Great cleanliness shall be approved in all work phases after completed pickling.
5.8 Flexible pipe connections

Pressurized flexible connections carrying flammable fluids or compressed air have to be type
approved.
Great care must be taken to ensure proper installation of flexible pipe connections between
resiliently mounted engines and ship’s piping.
● Flexible pipe connections must not be twisted
● Installation length of flexible pipe connections must be correct
● Minimum bending radius must be respected
● Piping must be concentrically aligned
● When specified the flow direction must be observed
● Mating flanges shall be clean from rust, burrs and anticorrosion coatings
● Bolts are to be tightened crosswise in several stages
● Flexible elements must not be painted
● Rubber bellows must be kept clean from oil and fuel
● The piping must be rigidly supported close to the flexible piping connections.

Fig 5-1 Flexible hoses
5.9 Clamping of pipes

It is very important to fix the pipes to rigid structures next to flexible pipe connections in order
to prevent damage caused by vibration. The following guidelines should be applied:
● Pipe clamps and supports next to the engine must be very rigid and welded to the steel
structure of the foundation.
● The first support should be located as close as possible to the flexible connection. Next
support should be 0.3-0.5 m from the first support.
● First three supports closest to the engine or generating set should be fixed supports. Where
necessary, sliding supports can be used after these three fixed supports to allow thermal
expansion of the pipe.
● Supports should never be welded directly to the pipe. Either pipe clamps or flange supports
should be used for flexible connection.
Examples of flange support structures are shown in Figure 5-2. A typical pipe clamp for a
fixed support is shown in Figure 5-3. Pipe clamps must be made of steel; plastic clamps or
similar may not be used.

Fig 5-2 Flange supports of flexible pipe connections (4V60L0796)
Fig 5-3 Pipe clamp for fixed support (4V61H0842)

Wärtsilä 31 Product Guide 6. Fuel Oil System
6. Fuel Oil System
6.1 Acceptable fuel characteristics

The fuel specifications are based on the ISO 8217:2012 (E) standard. Observe that a few
additional properties not included in the standard are listed in the tables. For maximum fuel
temperature before the engine, see chapter "Technical Data".
The fuel shall not contain any added substances or chemical waste, which jeopardizes the
safety of installations or adversely affects the performance of the engines or is harmful to
personnel or contributes overall to air pollution.
6.1.1 Marine Diesel Fuel (MDF)

Distillate fuel grades are ISO-F-DMX, DMA, DMZ, DMB. These fuel grades are referred to as
MDF (Marine Diesel Fuel).
The distillate grades mentioned above can be described as follows:
● DMX: A fuel which is suitable for use at ambient temperatures down to -15°C without
heating the fuel. Especially in merchant marine applications its use is restricted to lifeboat
engines and certain emergency equipment due to the reduced flash point. The low flash
point which is not meeting the SOLAS requirement can also prevent the use in other marine
applications, unless the fuel system is built according to special requirements. Also the
low viscosity (min. 1.4 cSt) can prevent the use in engines unless the fuel can be cooled
down enough to meet the min. injection viscosity limit of the engine.
● DMA: A high quality distillate, generally designated as MGO (Marine Gas Oil).
● DMZ: A high quality distillate, generally designated as MGO (Marine Gas Oil). An alternative
fuel grade for engines requiring a higher fuel viscosity than specified for DMA grade fuel.
● DMB: A general purpose fuel which may contain trace amounts of residual fuel and is
intended for engines not specifically designed to burn residual fuels. It is generally
designated as MDO (Marine Diesel Oil).
Table 6-1 MDF specifications
Property Unit ISO-F-DMA ISO-F-DMZ ISO-F-DMB Test method ref.
Viscosity, before injection pumps, min. 1) cSt 2.0 2.0 2.0
Viscosity, before injection pumps, max. 1) cSt 24 24 24
Viscosity at 40°C, min. cSt 2 3 2 ISO 3104
Viscosity at 40°C, max. cSt 6 6 11 ISO 3104
Density at 15°C, max. kg/m³ 890 890 900 ISO 3675 or 12185
Cetane index, min. 40 40 35 ISO 4264
Sulphur, max. % mass 1.5 1.5 2 ISO 8574 or 14596
Flash point, min. °C 60 60 60 ISO 2719
Hydrogen sulfide. max. 2) mg/kg 2 2 2 IP 570
Acid number, max. mg KOH/g 0.5 0.5 0.5 ASTM D664
Total sediment by hot filtration, max. % mass — — 0.1 3) ISO 10307-1
Oxidation stability, max. g/m3 25 25 25 4) ISO 12205
Carbon residue: micro method on the 10% volume % mass 0.30 0.30 — ISO 10370
distillation residue max.
Carbon residue: micro method, max. % mass — — 0.30 ISO 10370
Pour point (upper) , winter quality, max. 5) °C -6 -6 0 ISO 3016

6. Fuel Oil System Wärtsilä 31 Product Guide
Property Unit ISO-F-DMA ISO-F-DMZ ISO-F-DMB Test method ref.
Pour point (upper) , summer quality, max. 5) °C 0 0 6 ISO 3016
Appearance — Clear and bright 6) 3) 4) 7)
Water, max. % volume — — 0.3 3) ISO 3733
Ash, max. % mass 0.01 0.01 0.01 ISO 6245
Lubricity, corrected wear scar diameter (wsd 1.4) at µm 520 520 520 7) ISO 12156-1
60°C , max. 8)
Remarks:
1) Additional properties specified by Wärtsilä, which are not included in the ISO specification.
2) The implementation date for compliance with the limit shall be 1 July 2012. Until that the specified value is given for guidance.
3) If the sample is not clear and bright, the total sediment by hot filtration and water tests shall be required.
4) If the sample is not clear and bright, the test cannot be undertaken and hence the oxidation stability limit shall not apply.
5) It shall be ensured that the pour point is suitable for the equipment on board, especially if the ship operates in cold climates.
6) If the sample is dyed and not transparent, then the water limit and test method ISO 12937 shall apply.
7) If the sample is not clear and bright, the test cannot be undertaken and hence the lubricity limit shall not apply.
8) The requirement is applicable to fuels with a sulphur content below 500 mg/kg (0.050 % mass).

6.1.2 0,10% m/m sulphur fuels for SECA areas

Due to the new sulphur emission legislation being valid since 01.01.2015 in the specified SECA
areas many new max. 0.10 % m/m sulphur content fuels have entered the market. Some of
these fuels are not pure distillate fuels, but contain new refinery streams, like hydrocracker
bottoms or can also be blends of distillate and residual fuels. The new 0.10 % m/m sulphur
fuels are also called as “hybrid” fuels, since those can contain properties of both distillate and
residual fuels. In the existing ISO 8217:2017(E) standard the fuels are classed as RMA 10,
RMB 30 or RMD 80, if not fulling the DM grade category requirements, though from their
properties point of view this is generally not an optimum approach.
These fuels can be used in the Wärtsilä 31 engine type, but special attention shall be paid to
optimum operating conditions. See also Services Instruction WS02Q312.
RMA RMB RMD Test method

Characteristics Unit
10 30 80 reference
mm2/s 1,8 - 1,8 - 1,8 -
Kinematic viscosity bef. inj. pumps c) a) -
24 24 24
mm2/s
Kinematic viscosity at 50 °C, max. a) 10,00 30,00 80,00 ISO 3104
ISO 3675 or ISO

Density at 15 °C, max. kg/m3 920,0 960,0 975,0
12185
CCAI, max. e) - 850 860 860 ISO 8217, Annex F
% ISO 8574 or ISO
Sulphur, max.b) 0,10 0,10 0,10
m/m 14596
Flash point, min. °C 60,0 60,0 60,0 ISO 2719
Hydrogen sulfide, max. mg/kg 2,00 2,00 2,00 IP 570

mg
Acid number, max. 2,5 2,5 2,5 ASTM D664
KOH/g
%
Total sediment existent, max. 0,10 0,10 0,10 ISO 10307-2
m/m
%
Carbon residue, micro method, max. 2,50 10,00 14,00 ISO 10370
m/m
%
Asphaltenes, max. c) 1,5 6,0 8,0 ASTM D3279
m/m
Pour point (upper), max., winter quality
d) °C 0 0 30 ISO 3016
Pour point (upper), max., summer quality

d) °C 6 6 30 ISO 3016
Water max. % v/v 0,30 0,50 0,50 ASTM D6304-C
Water bef. engine, max. c) % v/v 0,30 0,30 0,30 ASTM D6304-C c)
% ISO 6245 or
Ash, max. 0,040 0,070 0,070
m/m LP1001 c,h)
IP 501, IP 470 or
Vanadium, max. f) mg/kg 50 150 150
ISO 14597
Sodium, max. f) mg/kg 50 100 100 IP 501 or IP 470
Sodium bef. engine, max. c, f) mg/kg 30 30 30 IP 501 or IP 470

IP 501, IP 470 or
Aluminium + Silicon, max. mg/kg 25 40 40
ISO 10478

RMA RMB RMD Test method

Characteristics Unit
10 30 80 reference
IP 501, IP 470 or
Aluminium + Silicon bef. engine, max.c) mg/kg 15 15 15
ISO 10478
Used lubricating oil: g)
- Calcium, max. mg/kg 30 30 30 IP 501 or IP 470
- Zinc, max. mg/kg 15 15 15 IP 501 or IP 470
- Phosphorus, max. mg/kg 15 15 15 IP 501 or IP 500
NOTE
a) 1 mm²/s = 1 cSt.
b) The purchaser shall define the maximum sulphur content in accordance with
relevant statutory limitations.
c) Additional properties specified by the engine manufacturer, which are not
included in the ISO 8217:2017(E) standard.
d) Purchasers shall ensure that this pour point is suitable for the equipment on
board / at the plant, especially if the ship operates / plant is located in cold climates.
e) Straight run residues show CCAI values in the 770 to 840 range and are very
good ignitors. Cracked residues delivered as bunkers may range from 840 to – in
exceptional cases – above 900. Most bunkers remain in the max. 850 to 870 range
at the moment. CCAI value cannot always be considered as an accurate tool to
determine fuels’ ignition properties, especially concerning fuels originating from
modern and more complex refinery processes.
f) Sodium contributes to hot corrosion on exhaust valves when combined with
high sulphur and vanadium contents. Sodium also strongly contributes to fouling
of the exhaust gas turbine blading at high loads. The aggressiveness of the fuel
depends on its proportions of sodium and vanadium, but also on the total amount
of ash. Hot corrosion and deposit formation are, however, also influenced by other
ash constituents. It is therefore difficult to set strict limits based only on the sodium
and vanadium content of the fuel. Also a fuel with lower sodium and vanadium
contents than specified above, can cause hot corrosion on engine components.
g) The fuel shall be free from used lubricating oil (ULO). A fuel shall be considered
to contain ULO when either one of the following conditions is met:
- Calcium > 30 mg/kg and zinc > 15 mg/kg OR
- Calcium > 30 mg/kg and phosphorus > 15 mg/kg
h) The ashing temperatures can vary when different test methods are used having
an influence on the test result.

6.1.3 Heavy Fuel Oil (HFO)

Residual fuel grades are referred to as HFO (Heavy Fuel Oil). The fuel specification HFO 2
covers the categories ISO-F-RMA 10 to RMK 700. Fuels fulfilling the specification HFO 1
permit longer overhaul intervals of specific engine components than HFO 2.
Table 6-2 HFO specifications
Property Unit Limit HFO 1 Limit HFO 2 Test method ref.
Viscosity, before injection pumps 1) cSt 16...24 16...24
Viscosity at 50°C, max. cSt 700 700 ISO 3104
Density at 15°C, max. kg/m³ 991 / 1010 2) 991 / 1010 2) ISO 3675 or 12185
CCAI, max.3) 850 870 ISO 8217, Annex F
Sulphur, max. 4) 5) % mass Statutory requirements ISO 8754 or 14596
Flash point, min. °C 60 60 ISO 2719
Hydrogen sulfide, max. 6) mg/kg 2 2 IP 570
Acid number, max. mg KOH/g 2.5 2.5 ASTM D664
Total sediment aged, max. % mass 0.1 0.1 ISO 10307-2
Carbon residue, micro method, max. % mass 15 20 ISO 10370
Asphaltenes, max.1) % mass 8 14 ASTM D 3279
Pour point (upper), max. 7) °C 30 30 ISO 3016
Water, max. % volume 0.5 0.5 ISO 3733 or ASTM

D6304-C 1)
Water before engine, max.1) % volume 0.3 0.3 ISO 3733 or ASTM
D6304-C 1)
Ash, max. % mass 0.05 0.15 ISO 6245 or LP1001 1)
Vanadium, max. 5) mg/kg 100 450 ISO 14597 or IP 501

or IP 470
Sodium, max. 5) mg/kg 50 100 IP 501 or IP 470
Sodium before engine, max.1) 5) mg/kg 30 30 IP 501 or IP 470
Aluminium + Silicon, max. mg/kg 30 60 ISO 10478 or IP 501

or IP 470
Aluminium + Silicon before engine, max.1) mg/kg 15 15 ISO 10478 or IP 501

or IP 470
Used lubricating oil, calcium, max. 8) mg/kg 30 30 IP 501 or IP 470
Used lubricating oil, zinc, max. 8) mg/kg 15 15 IP 501 or IP 470
Used lubricating oil, phosphorus, max. 8) mg/kg 15 15 IP 501 or IP 500
Remarks:
1) Additional properties specified by Wärtsilä, which are not included in the ISO specification.
2) Max. 1010 kg/m³ at 15°C provided that the fuel treatment system can remove water and solids (sediment, sodium, aluminium,
silicon) before the engine to specified levels.
3) Straight run residues show CCAI values in the 770 to 840 range and have very good ignition quality. Cracked residues delivered
as bunkers may range from 840 to - in exceptional cases - above 900. Most bunkers remain in the max. 850 to 870 range at
the moment. CCAI value cannot always be considered as an accurate tool to determine the ignition properties of the fuel,
especially concerning fuels originating from modern and more complex refinery process.
4) The max. sulphur content must be defined in accordance with relevant statutory limitations.
5) Sodium contributes to hot corrosion on the exhaust valves when combined with high sulphur and vanadium contents. Sodium
also strongly contributes to fouling of the exhaust gas turbine blading at high loads. The aggressiveness of the fuel depends
on its proportions of sodium and vanadium and also on the total amount of ash. Hot corrosion and deposit formation are,
however, also influenced by other ash constituents. It is therefore difficult to set strict limits based only on the sodium and
vanadium content of the fuel. Also a fuel with lower sodium and vanadium contents than specified above, can cause hot
corrosion on engine components.
6) The implementation date for compliance with the limit shall be 1 July 2012. Until that, the specified value is given for guidance.
7) It shall be ensured that the pour point is suitable for the equipment on board, especially if the ship operates in cold climates.

8) The fuel shall be free from used lubricating oil (ULO). A fuel shall be considered to contain ULO when either one of the following
conditions is met:
● Calcium > 30 mg/kg and zinc > 15 mg/kg

● Calcium > 30 mg/kg and phosphorus > 15 mg/kg
NOTE
b) if not within the given limits, the maximum sulphur content to be defined in
accordance with relevant statutory limitations.
c) It shall be ensured that the pour point is suitable for the equipment on board,
especially if the ship operates in cold climates.
d) If the sample is not clear and bright, the total sediment by hot filtration and water
tests shall be required.
e) If the sample is not clear and bright, the test cannot be undertaken and hence
the oxidation stability limit shall not apply.
f) If the sample is not clear and bright, the test cannot be undertaken and hence
the lubricity limit shall not apply.
g) The requirement is applicable to fuels with a sulphur content below 500 mg/kg
(0.050 % mass).
h) Additional properties specified by Wärtsilä, which are not included in the ISO
specification.
i) If the sample is dyed and not transparent, then the water limit and test method
ISO 12937 shall apply.
6.2 External fuel oil system

The design of the external fuel system may vary from ship to ship, but every system should
provide well cleaned fuel of correct viscosity and pressure to each engine. Temperature control
is required to maintain stable and correct viscosity of the fuel before the injection pumps (see
Technical data). Sufficient circulation through every engine connected to the same circuit must
be ensured in all operating conditions.
The fuel treatment system should comprise at least one settling tank and two separators.
Correct dimensioning of HFO separators is of greatest importance, and therefore the
recommendations of the separator manufacturer must be closely followed. Poorly centrifuged
fuel is harmful to the engine and a high content of water may also damage the fuel feed system.
Injection pumps generate pressure pulses into the fuel feed and return piping. The fuel pipes
between the feed unit and the engine must be properly clamped to rigid structures. The
distance between the fixing points should be at close distance next to the engine. See chapter
Piping design, treatment and installation.
A connection for compressed air should be provided before the engine, together with a drain
from the fuel return line to the clean leakage fuel or overflow tank. With this arrangement it is
possible to blow out fuel from the engine prior to maintenance work, to avoid spilling.
NOTE
In multiple engine installations, where several engines are connected to the same
fuel feed circuit, it must be possible to close the fuel supply and return lines
connected to the engine individually. This is a SOLAS requirement. It is further
stipulated that the means of isolation shall not affect the operation of the other
engines, and it shall be possible to close the fuel lines from a position that is not
rendered inaccessible due to fire on any of the engines.

6.2.1 Fuel heating requirements HFO

Heating is required for:
● Bunker tanks, settling tanks, day tanks
● Pipes (trace heating)
● Separators
● Fuel feeder/booster units
To enable pumping the temperature of bunker tanks must always be maintained 5...10°C
above the pour point, typically at 40...50°C. The heating coils can be designed for a temperature
of 60°C.
The tank heating capacity is determined by the heat loss from the bunker tank and the desired
temperature increase rate.
Fig 6-1 Fuel oil viscosity-temperature diagram for determining the pre-heating
temperatures of fuel oils (4V92G0071b)
Example 1: A fuel oil with a viscosity of 380 cSt (A) at 50°C (B) or 80 cSt at 80°C (C) must be
pre-heated to 115 - 130°C (D-E) before the fuel high pressure pumps, to 98°C (F) at the

separator and to minimum 40°C (G) in the bunker tanks. The fuel oil may not be pumpable
below 36°C (H).
To obtain temperatures for intermediate viscosities, draw a line from the known
viscosity/temperature point in parallel to the nearest viscosity/temperature line in the diagram.
Example 2: Known viscosity 60 cSt at 50°C (K). The following can be read along the dotted
line: viscosity at 80°C = 20 cSt, temperature at fuel high pressure pumps 74 - 87°C, separating
temperature 86°C, minimum bunker tank temperature 28°C.
6.2.2 Fuel tanks

The fuel oil is first transferred from the bunker tanks to settling tanks for initial separation of
sludge and water. After centrifuging the fuel oil is transferred to day tanks, from which fuel is
supplied to the engines.
6.2.2.1 Settling tank, HFO (1T02) and MDF (1T10)

Separate settling tanks for HFO and MDF are recommended.
To ensure sufficient time for settling (water and sediment separation), the capacity of each
tank should be sufficient for min. 24 hours operation at maximum fuel consumption. The tanks
should be provided with internal baffles to achieve efficient settling and have a sloped bottom
for proper draining. The temperature in HFO settling tanks should be maintained between
50°C and 70°C, which requires heating coils and insulation of the tank. Usually MDF settling
tanks do not need heating or insulation, but the tank temperature should be in the range
20...40°C.
6.2.2.2 Day tank, HFO (1T03) and MDF (1T06)

Two day tanks for HFO are to be provided, each with a capacity sufficient for at least 8 hours
operation at maximum fuel consumption. A separate tank is to be provided for MDF. The
capacity of the MDF tank should ensure fuel supply for 8 hours. Settling tanks may not be
used instead of day tanks.
The day tank must be designed so that accumulation of sludge near the suction pipe is
prevented and the bottom of the tank should be sloped to ensure efficient draining. HFO day
tanks shall be provided with heating coils and insulation. It is recommended that the viscosity
is kept below 140 cSt in the day tanks. Due to risk of wax formation, fuels with a viscosity
lower than 50 cSt at 50°C must be kept at a temperature higher than the viscosity would
require. Continuous separation is nowadays common practice, which means that the HFO
day tank temperature normally remains above 90°C. The temperature in the MDF day tank
should be in the range 20...40°C. The level of the tank must ensure a positive static pressure
on the suction side of the fuel feed pumps.
6.2.2.3 Leak fuel tank, clean fuel (1T04)

Clean leak fuel is drained by gravity from the engine. The fuel should be collected in a separate
clean leak fuel tank, from where it can be pumped to the day tank and reused without
separation. The pipes from the engine to the clean leak fuel tank should be arranged continuosly
sloping. The tank and the pipes must be heated and insulated, unless the installation is designed
for operation on MDF only.
The leak fuel piping should be fully closed to prevent dirt from entering the system.
6.2.2.4 Leak fuel tank, dirty fuel (1T07)

In normal operation no fuel should leak out from the components of the fuel system. In
connection with maintenance, or due to unforeseen leaks, fuel or water may spill in the hot
box of the engine. The spilled liquids are collected and drained by gravity from the engine
through the dirty fuel connection.

Dirty leak fuel shall be led to a sludge tank. The tank and the pipes must be heated and
insulated, unless the installation is designed for operation exclusively on MDF.
6.2.3 Fuel treatment

6.2.3.1 Separation
Heavy fuel (residual, and mixtures of residuals and distillates) must be cleaned in an efficient
centrifugal separator before it is transferred to the day tank.
Classification rules require the separator arrangement to be redundant so that required capacity
is maintained with any one unit out of operation.
All recommendations from the separator manufacturer must be closely followed.
Centrifugal disc stack separators are recommended also for installations operating on MDF
only, to remove water and possible contaminants. The capacity of MDF separators should be
sufficient to ensure the fuel supply at maximum fuel consumption. Would a centrifugal separator
be considered too expensive for a MDF installation, then it can be accepted to use coalescing
type filters instead. A coalescing filter is usually installed on the suction side of the circulation
pump in the fuel feed system. The filter must have a low pressure drop to avoid pump cavitation.
Separator mode of operation

The best separation efficiency is achieved when also the stand-by separator is in operation
all the time, and the throughput is reduced according to actual consumption.
Separators with monitoring of cleaned fuel (without gravity disc) operating on a continuous
basis can handle fuels with densities exceeding 991 kg/m3 at 15°C. In this case the main and
stand-by separators should be run in parallel.
When separators with gravity disc are used, then each stand-by separator should be operated
in series with another separator, so that the first separator acts as a purifier and the second
as clarifier. This arrangement can be used for fuels with a density of max. 991 kg/m3 at 15°C.
The separators must be of the same size.
Separation efficiency
The term Certified Flow Rate (CFR) has been introduced to express the performance of
separators according to a common standard. CFR is defined as the flow rate in l/h, 30 minutes
after sludge discharge, at which the separation efficiency of the separator is 85%, when using
defined test oils and test particles. CFR is defined for equivalent fuel oil viscosities of 380 cSt
and 700 cSt at 50°C. More information can be found in the CEN (European Committee for
Standardisation) document CWA 15375:2005 (E).
The separation efficiency is measure of the separator's capability to remove specified test
particles. The separation efficiency is defined as follows:
where:
n = separation efficiency [%]
Cout = number of test particles in cleaned test oil
Cin = number of test particles in test oil before separator
6.2.3.2 Separator unit (1N02/1N05)

Separators are usually supplied as pre-assembled units designed by the separator
manufacturer.

Typically separator modules are equipped with:

● Suction strainer (1F02)
● Feed pump (1P02)
● Pre-heater (1E01)
● Sludge tank (1T05)
● Separator (1S01/1S02)
● Sludge pump
● Control cabinets including motor starters and monitoring
Fig 6-2 Fuel transfer and separating system (V76F6626F)
6.2.3.3 Separator feed pumps (1P02)

Feed pumps should be dimensioned for the actual fuel quality and recommended throughput
of the separator. The pump should be protected by a suction strainer (mesh size about 0.5
mm)
An approved system for control of the fuel feed rate to the separator is required.
Design data: HFO MDF
Design pressure 0.5 MPa (5 bar) 0.5 MPa (5 bar)

Design temperature 100°C 50°C
Viscosity for dimensioning electric motor 1000 cSt 100 cSt
6.2.3.4 Separator pre-heater (1E01)

The pre-heater is dimensioned according to the feed pump capacity and a given settling tank
temperature.
The surface temperature in the heater must not be too high in order to avoid cracking of the
fuel. The temperature control must be able to maintain the fuel temperature within ± 2°C.
Recommended fuel temperature after the heater depends on the viscosity, but it is typically
98°C for HFO and 20...40°C for MDF. The optimum operating temperature is defined by the
sperarator manufacturer.
The required minimum capacity of the heater is:
where:
P = heater capacity [kW]
Q = capacity of the separator feed pump [l/h]
ΔT = temperature rise in heater [°C]
For heavy fuels ΔT = 48°C can be used, i.e. a settling tank temperature of 50°C. Fuels having
a viscosity higher than 5 cSt at 50°C require pre-heating before the separator.
The heaters to be provided with safety valves and drain pipes to a leakage tank (so that the
possible leakage can be detected).
6.2.3.5 Separator (1S01/1S02)

Based on a separation time of 23 or 23.5 h/day, the service throughput Q [l/h] of the separator
can be estimated with the formula:
where:
P = max. continuous rating of the diesel engine(s) [kW]
b = specific fuel consumption + 15% safety margin [g/kWh]
ρ = density of the fuel [kg/m3]
t = daily separating time for self cleaning separator [h] (usually = 23 h or 23.5 h)
The flow rates recommended for the separator and the grade of fuel must not be exceeded.
The lower the flow rate the better the separation efficiency.
Sample valves must be placed before and after the separator.

6.2.3.6 MDF separator in HFO installations (1S02)

A separator for MDF is recommended also for installations operating primarily on HFO. The
MDF separator can be a smaller size dedicated MDF separator, or a stand-by HFO separator
used for MDF.
6.2.3.7 Sludge tank (1T05)

The sludge tank should be located directly beneath the separators, or as close as possible
below the separators, unless it is integrated in the separator unit. The sludge pipe must be
continuously falling.

6.2.4 Fuel feed system - MDF installations
Fig 6-3 MDF fuel oil system, single main engine (DAAF314554B)
System components Pipe connections Size
1E04 Cooler (MDF) 101 Fuel inlet DN25
1F04 Automatic filter (MDF) 102 Fuel outlet DN25
1F05 Fine filter (MDF) 1033 Leak fuel drain, clean fuel OD28
1F07 Suction strainer (MDF) 1041 Leak fuel drain, dirty fuel DN32
1I03 Flow meter (MDF) 1042 Leak fuel drain, dirty fuel DN32
1P03 Circulation pump (MDF) 1043 Leak fuel drain, dirty fuel DN32
1P08 Stand-by pump (MDF) 1044 Leak fuel drain, dirty fuel DN32
1T06 Day tank (MDF)
1V10 Quick closing valve (fuel oil tank)

Fig 6-4 MDF fuel oil system, single main engine with engine driven fuel feed pump
(DAAF301495B)
1P08 Stand-by pump (MDF) 1043 Leak fuel drain, dirty fuel DN32
1T06 Day tank (MDF) 1044 Leak fuel drain, dirty fuel DN32
1V10 Quick closing valve (fuel oil tank) 106 Fuel to external filter DN25
107 Fuel from external filter DN25

Fig 6-5 MDF fuel oil system, multiple engines (DAAF301496B)
1P03 Circulation pump (MDF) 1043 Leak fuel drain, dirty fuel DN32
1T06 Day tank (MDF) 1044 Leak fuel drain, dirty fuel DN32
1V10 Quick closing valve (fuel oil tank)

If the engines are to be operated on MDF only, heating of the fuel is normally not necessary.
In such case it is sufficient to install the equipment listed below. Some of the equipment listed
below is also to be installed in the MDF part of a HFO fuel oil system.
6.2.4.1 Circulation pump, MDF (1P03)

The circulation pump maintains the pressure at the high pressure pumps and circulates the
fuel in the system. It is recommended to use a screw pump as circulation pump. A suction
strainer with a fineness of 0.5 mm should be installed before each pump. There must be a
positive static pressure of about 30 kPa on the suction side of the pump.
Design data:
Design pressure 1.6 MPa (16 bar)
Max. total pressure (safety valve) 1.2 MPa (12 bar)
Nominal pressure see chapter "Technical Data"
Design temperature 50°C
Viscosity for dimensioning of electric 90 cSt

motor
6.2.4.2 Circulation pump (1P12)

The purpose of the circulation pump is to ensure equal circulation through all engines. With
a common circulation pump for several engines, the fuel flow will be divided according to the
pressure distribution in the system (which also tends to change over time) and the control
valve on the engine has a very flat pressure versus flow curve.
In installations where MDF is fed directly from the MDF tank (1T06) to the circulation pump,
a suction strainer (1F07) with a fineness of 0.5 mm shall be installed to protect the circulation
pump. The suction strainer can be common for all circulation pumps.
Design data:
Capacity 3.6 m3/h per high pressure pump on the engine

Pressure for dimensioning of electric motor (ΔP): If MDF is fed directly from day tank: 0.12 MPa (1.2 bar)
If all fuel is fed through feeder/booster unit: 0.6 MPa (6 bar)
Viscosity for dimensioning of electric motor 500 cSt
6.2.4.3 Flow meter, MDF (1I03)

If required, a flow meter is used for monitoring of the fuel consumption. The total resistance
of the flow meter and the suction strainer must be small enough to ensure a positive static
pressure of about 30 kPa on the suction side of the circulation pump. There should be a
by-pass line around the consumption meter, which opens automatically in case of excessive
pressure drop.
6.2.4.4 Automatic filter (1F04)

It is recommended to select an automatic filter with a manually cleaned filter in the bypass
line.
Design data:
Fuel viscosity According to fuel specification

Design flow Equal to feed pump capacity
Fineness:
6 μm (absolute mesh size)
- automatic filter
β_18=75
Maximum permitted pressure drops at 14 cSt:
- clean filter 20 kPa (0.2 bar)
- alarm 80 kPa (0.8 bar)
6.2.4.5 Fine filter, MDF (1F05)

The fuel oil fine filter is a full flow duplex type filter with steel net. This filter must be installed
as near the engine as possible.
The diameter of the pipe between the fine filter and the engine should be the same as the
diameter before the filters.
Design data:
Fuel viscosity according to fuel specifications
Design flow Larger than feed/circulation pump capacity
Fineness 34 μm (absolute mesh size)

β_50=75
6.2.4.6 Pressure control valve, MDF (1V02)

The pressure control valve is installed when the installation includes a feeder/booster unit for
HFO and there is a return line from the engine to the MDF day tank. The purpose of the valve
is to increase the pressure in the return line so that the required pressure at the engine is
achieved.
Design data:
Capacity Equal to circulation pump
Set point 0.4...0.7 MPa (4...7 bar)

6.2.4.7 MDF cooler (1E04)

The fuel viscosity may not drop below the minimum value stated in Technical data. When
operating on MDF, the practical consequence is that the fuel oil inlet temperature must be
kept below 45°C. Very light fuel grades may require even lower temperature.
Sustained operation on MDF usually requires a fuel oil cooler. The cooler is to be installed in
the return line after the engine(s). LT-water is normally used as cooling medium.
If MDF viscosity in day tank drops below stated minimum viscosity limit then it is recommended
to install an MDF cooler into the engine fuel supply line in order to have reliable viscosity
control.
Design data:
Max. pressure drop, fuel oil 80 kPa (0.8 bar)
Max. pressure drop, water 60 kPa (0.6 bar)
Margin (heat rate, fouling) min. 15%
Design temperature MDF/HFO installa- 50/150°C

tion

6.2.5 Fuel feed system - HFO installations
Fig 6-6 HFO fuel oil system, single engine installation (DAAF301497B)
System components:
1E02 Heater (booster unit) 1P04 Fuel feed pump (booster unit)
1E03 Cooler (booster unit) 1P06 Circulation pump (booster unit)
1E04 Cooler (MDF) 1T03 Day tank (HFO)
1F03 Safety filter (HFO) 1T06 Day tank (MDF)
1F06 Suction filter (booster unit) 1T08 De-aeration tank (booster unit)
1F08 Automatic filter (booster unit) 1V01 Changeover valve
1I01 Flow meter (booster unit) 1V03 Pressure control valve (booster unit)
1I02 Viscosity meter (booster unit) 1V07 Venting valve (booster unit)
1N01 Feeder/booster unit 1V10 Quick closing valve (fuel oil tank)
Pipe connections: Size
101 Fuel inlet DN25
102 Fuel outlet DN25
1033 Leak fuel drain, clean fuel OD28
1041-1044 Leak fuel drain, dirty fuel DN32

Fig 6-7 HFO fuel oil system, multiple engine installation (DAAF301498B)
System components:
1E02 Heater (booster unit) 1P04 Fuel feed pump (booster unit)
1E03 Cooler (booster unit) 1P06 Circulation pump (booster unit)
1E04 Cooler (MDF) 1P12 Circulation pump (HFO/MDF)
1F03 Safety filter (HFO) 1T03 Day tank (HFO)
1F04 Automatic filter (MDF) 1T06 Day tank (MDF)
1F06 Suction filter (booster unit) 1T08 De-aeration tank (booster unit)
1F07 Suction strainer (MDF) 1V01 Changeover valve
1F08 Automatic filter (booster unit) 1V02 Pressure control valve (MDF)
1I01 Flow meter (booster unit) 1V03 Pressure control valve (booster unit)
1I02 Viscosity meter (booster unit) 1V05 Overflow valve (Booster unit)
1N01 Feeder/booster unit 1V07 Venting valve (booster unit)
1P03 Circulation pump (MDF) 1V10 Quick closing valve (fuel oil tank)
Pipe connections: Size
101 Fuel inlet DN25
102 Fuel outlet DN25
1033 Leak fuel drain, clean fuel OD28
1041-1044 Leak fuel drain, dirty fuel DN32

HFO pipes shall be properly insulated. If the viscosity of the fuel is 180 cSt/50°C or higher,
the pipes must be equipped with trace heating. It sha ll be possible to shut off the heating of
the pipes when operating on MDF (trace heating to be grouped logically).
6.2.5.1 Starting and stopping

The engine can be started and stopped on HFO provided that the engine and the fuel system
are pre-heated to operating temperature. The fuel must be continuously circulated also through
a stopped engine in order to maintain the operating temperature. Changeover to MDF for start
and stop is not required.
Prior to overhaul or shutdown of the external system the engine fuel system shall be flushed
and filled with MDF.
6.2.5.2 Changeover from HFO to MDF

The control sequence and the equipment for changing fuel during operation must ensure a
smooth change in fuel temperature and viscosity. When MDF is fed through the HFO
feeder/booster unit, the volume in the system is sufficient to ensure a reasonably smooth
transfer.
When there are separate circulating pumps for MDF, then the fuel change should be performed
with the HFO feeder/booster unit before switching over to the MDF circulating pumps. As
mentioned earlier, sustained operation on MDF usually requires a fuel oil cooler. The viscosity
at the engine shall not drop below the minimum limit stated in chapter Technical data.
6.2.5.3 Feeder/booster unit (1N01)

A completely assembled feeder/booster unit can be supplied. This unit comprises the following
equipment:
● Two suction strainers
● Two fuel feed pumps of screw type, equipped with built-on safety valves and electric motors
● One pressure control/overflow valve
● One pressurized de-aeration tank, equipped with a level switch operated vent valve
● Two circulating pumps, same type as the fuel feed pumps
● Two heaters, steam, electric or thermal oil (one heater in operation, the other as spare)
● One automatic back-flushing filter with by-pass filter
● One viscosimeter for control of the heaters
● One control valve for steam or thermal oil heaters, a control cabinet for electric heaters
● One temperature sensor for emergency control of the heaters
● One control cabinet including starters for pumps
● One alarm panel
The above equipment is built on a steel frame, which can be welded or bolted to its foundation
in the ship. The unit has all internal wiring and piping fully assembled. All HFO pipes are
insulated and provided with trace heating.
Fuel feed pump, booster unit (1P04)

The feed pump maintains the pressure in the fuel feed system. It is recommended to use a
screw pump as feed pump. The capacity of the feed pump must be sufficient to prevent
pressure drop during flushing of the automatic filter.
A suction strainer with a fineness of 0.5 mm should be installed before each pump. There
must be a positive static pressure of about 30 kPa on the suction side of the pump.

Design data:
Total consumption of the connected engines added with
Capacity the flush quantity of the automatic filter (1F08) and 15%
margin.
Viscosity for dimensioning of electric motor 1000 cSt
Pressure control valve, booster unit (1V03)

The pressure control valve in the feeder/booster unit maintains the pressure in the de-aeration
tank by directing the surplus flow to the suction side of the feed pump.
Design data:
Capacity Equal to feed pump
Set-point 0.3...0.5 MPa (3...5 bar)
Fine filter (1F05)

The fuel oil fine filter is a full flow duplex type filter with steel net. This filter must be installed
as near the engine as possible.
The diameter of the pipe between the fine filter and the engine should be the same as the
diameter before the filters.
Design data:
Fuel viscosity according to fuel specifications
Design flow Larger than feed/circulation pump capacity
Fineness 25 μm (absolute mesh size)
Automatic filter, booster unit (1F08)

It is recommended to select an automatic filter with a manually cleaned filter in the bypass
line. The automatic filter must be installed before the heater, between the feed pump and the
de-aeration tank, and it should be equipped with a heating jacket. Overheating (temperature
exceeding 100°C) is however to be prevented, and it must be possible to switch off the heating
for operation on MDF.
Design data:

Preheating If fuel viscosity is higher than 25 cSt/100°C
Design flow Equal to feed pump capacity
Fineness:
- automatic filter 6 μm (absolute mesh size)
- by-pass filter 6 μm (absolute mesh size)
Flow meter, booster unit (1I01)

If a fuel consumption meter is required, it should be fitted between the feed pumps and the
de-aeration tank. When it is desired to monitor the fuel consumption of individual engines in
a multiple engine installation, two flow meters per engine are to be installed: one in the feed
line and one in the return line of each engine.
There should be a by-pass line around the consumption meter, which opens automatically in
case of excessive pressure drop.
If the consumption meter is provided with a prefilter, an alarm for high pressure difference
across the filter is recommended.
De-aeration tank, booster unit (1T08)

It shall be equipped with a low level alarm switch and a vent valve. The vent pipe should, if
possible, be led downwards, e.g. to the overflow tank. The tank must be insulated and equipped
with a heating coil. The volume of the tank should be at least 100 l.
Circulation pump, booster unit (1P06)

The purpose of this pump is to circulate the fuel in the system and to maintain the required
pressure at the high pressure pumps, which is stated in the chapter Technical data. By
circulating the fuel in the system it also maintains correct viscosity, and keeps the piping and
the high pressure pumps at operating temperature.
Heater, booster unit (1E02)

The heater must be able to maintain a fuel viscosity of 14 cSt at maximum fuel consumption,
with fuel of the specified grade and a given day tank temperature (required viscosity at high
pressure pumps stated in Technical data). When operating on high viscosity fuels, the fuel
temperature at the engine inlet may not exceed 135°C however.
The power of the heater is to be controlled by a viscosimeter. The set-point of the viscosimeter
shall be somewhat lower than the required viscosity at the high pressure pumps to compensate
for heat losses in the pipes. A thermostat should be fitted as a backup to the viscosity control.
To avoid cracking of the fuel the surface temperature in the heater must not be too high. The
heat transfer rate in relation to the surface area must not exceed 1.5 W/cm2.
The required heater capacity can be estimated with the following formula:

where:
P = heater capacity (kW)
Q = total fuel consumption at full output + 15% margin [l/h]
ΔT = temperature rise in heater [°C]
Viscosimeter, booster unit (1I02)

The heater is to be controlled by a viscosimeter. The viscosimeter should be of a design that
can withstand the pressure peaks caused by the high pressure pumps of the diesel engine.
Design data:
Operating range 0...50 cSt
Design pressure 4 MPa (40 bar)
6.2.5.4 Safety filter, HFO (1F03)

The safety filter is a full flow duplex type filter with steel net. The filter should be equipped with
a heating jacket. The safety filter or pump and filter unit shall be installed as close as possible
to the engine.
Design data:
Design flow Equal to circulation pump capacity

34 μm (absolute mesh size)
Filter fineness
Β50 = 75 (ISO 16889)
Maximum permitted pressure drops at 14 cSt: Clean filter: 20 kPa (0.2 bar)
Alarm: 80 kPa (0.8 bar)
6.2.5.5 Overflow valve, HFO (1V05)

When several engines are connected to the same feeder/booster unit an overflow valve is
needed between the feed line and the return line. The overflow valve limits the maximum
pressure in the feed line, when the fuel lines to a parallel engine are closed for maintenance
purposes.
The overflow valve should be dimensioned to secure a stable pressure over the whole operating
range.
Design data:
Capacity Equal to circulation pump (1P06)

6.2.6 Flushing
The external piping system must be thoroughly flushed before the engines are connected and
fuel is circulated through the engines. The piping system must have provisions for installation
of a temporary flushing filter.
The fuel pipes at the engine (connections 101 and 102) are disconnected and the supply and
return lines are connected with a temporary pipe or hose on the installation side. All filter
inserts are removed, except in the flushing filter of course. The automatic filter and the
viscosimeter should be bypassed to prevent damage. The fineness of the flushing filter should
be 35 μm or finer.

Wärtsilä 31 Product Guide 7. Lubricating Oil System
7. Lubricating Oil System
7.1 Lubricating oil requirements

7.1.1 Engine lubricating oil
The lubricating oil must be of viscosity class SAE 40 and have a viscosity index (VI) of minimum
95. The lubricating oil alkalinity (BN) is tied to the fuel grade, as shown in the table below. BN
is an abbreviation of Base Number. The value indicates milligrams KOH per gram of oil.
Table 7-1 Fuel standards and lubricating oil requirements
Category Fuel standard Lubricating oil BN
ASTM D 975-01, GRADE NO. 1-D, 2-D, 4-D

BS MA 100: 1996 DMX, DMA, DMB
A 10...30
CIMAC 2003 DX, DA, DB
ISO8217: 2012(E) ISO-F-DMX, DMB
ASTM D 975-01 GRADE NO. 1-D, 2-D, 4-D

BS MA 100: 1996 DMX, DMA, DMB
B 15...30
CIMAC 2003 DX, DA, DB
ISO 8217: 2012(E) ISO-F-DMX - DMB
ASTM D 975-01, GRADE NO. 4-D

ASTM D 396-04, GRADE NO. 5-6
C BS MA 100: 1996 DMC, RMA10-RMK55 30...55
CIMAC 2003 DC, A30-K700
ISO 8217: 2012(E) RMA10-RMK 700
BN 50-55 lubricants are to be selected in the first place for operation on HFO. BN 40 lubricants
can also be used with HFO provided that the sulphur content of the fuel is relatively low, and
the BN remains above the condemning limit for acceptable oil change intervals. BN 30
lubricating oils should be used together with HFO only in special cases; for example in SCR
(Selective Catalyctic Reduction) installations, if better total economy can be achieved despite
shorter oil change intervals. Lower BN may have a positive influence on the lifetime of the
SCR catalyst.
It is not harmful to the engine to use a higher BN than recommended for the fuel grade.
Different oil brands may not be blended, unless it is approved by the oil suppliers. Blending
of different oils must also be validated by Wärtsilä, if the engine still under warranty.
An updated list of validated lubricating oils is supplied for every installation.

7. Lubricating Oil System Wärtsilä 31 Product Guide
7.2 External lubricating oil system
Fig 7-1 Lubricating oil system, main engines with dry sump (DAAF301499A)
System components:
2E02 Heater (separator unit) 2P03 Separator pump (separator unit)
2F01 Suction strainer (main lubricating oil pump) 2P04 Stand-by pump
2F03 Suction filter (separator unit) 2S01 Separator
2F04 Suction strainer (Prelubricating oil pump) 2S02 Condensate trap
2F06 Suction strainer (stand-by pump) 2T01 System oil tank
2N01 Separator unit 2T06 Sludge tank
2P02 Pre lube oil pump 2V03 Pressure control valve
Pipe connections: 8V - 10V 12V - 16V
202 (* Lubricating oil outlet DN200 DN250
203 Lubricating oil to engine driven pump DN200 DN250
206 Lubricating oil from priming pump DN80 DN80
208 Lubricating oil from electric driven pump DN150 DN150
701 Crankcase air vent DN125 DN150
* Size depends on engine configuration

Fig 7-2 Lubricating oil system, single engine & wet sump (DAAF301501B)
System components:
2E02 Heater (separator unit) 2S02 Condensate trap
2F03 Suction filter (separator unit) 2T03 New oil tank
2N01 Separator unit 2T04 Renovating oil tank
2P03 Separator pump (separator unit) 2T05 Renovated oil tank
2P04 Stand-by pump 2T06 Sludge tank
2S01 Separator 2V03 Pressure control valve
207(** Lube oil to el. driven pump DN200 / DN250
208 Lube oil from el. driven pump DN150 DN150
213 Lubricating oil from separator and filling DN40 DN40
214 Lubricating oil to separator and drain DN40 DN40
217 Lube oil to generator bearing DN40 DN40
218 Lube oil from generator bearing DN40 DN40
* Size depends on engine configuration

Fig 7-3 Lubricating oil system (MDF), multiple engines & wet sump (DAAF301500A)
System components:
2E02 Heater (separator unit) 2S02 Condensate trap
2F03 Suction filter (separator unit) 2T03 New oil tank
2N01 Separator unit 2T04 Renovating oil tank
2P03 Separator pump (separator unit) 2T05 Renovated oil tank
2S01 Separator 2T06 Sludge tank
213 Lubricating oil from separator and filling DN40 DN40
214 Lubricating oil to separator and drain DN40 DN40
217 Lube oil to generator bearing DN40 DN40
218 Lube oil from generator bearing DN40 DN40

7.2.1 Separation system

7.2.1.1 Separator unit (2N01)
Auxiliary engines operating on a fuel having a viscosity of max. 380 cSt / 50°C may have a
common lubricating oil separator unit. Two engines may have a common lubricating oil
separator unit. In installations with four or more engines two lubricating oil separator units
should be installed.
Separators are usually supplied as pre-assembled units.
Typically lubricating oil separator units are equipped with:
● Feed pump with suction strainer and safety valve
● Preheater
● Separator
● Control cabinet
The lubricating oil separator unit may also be equipped with an intermediate sludge tank and
a sludge pump, which offers flexibility in placement of the separator since it is not necessary
to have a sludge tank directly beneath the separator.
Separator feed pump (2P03)

The feed pump must be selected to match the recommended throughput of the separator.
Normally the pump is supplied and matched to the separator by the separator manufacturer.
The lowest foreseen temperature in the system oil tank (after a long stop) must be taken into
account when dimensioning the electric motor.
Separator preheater (2E02)

The preheater is to be dimensioned according to the feed pump capacity and the temperature
in the system oil tank. When the engine is running, the temperature in the system oil tank
located in the ship's bottom is normally 65...75°C. To enable separation with a stopped engine
the heater capacity must be sufficient to maintain the required temperature without heat supply
from the engine.
Recommended oil temperature after the heater is 95°C.
It shall be considered that, while the engine is stopped in stand-by mode without LT water
circulation, the separator unit may be heating up the total amount of lubricating oil in the oil
tank to a value higher than the nominal one required at engine inlet, after lube oil cooler (see
Technical Data chapter). Higher oil temperatures at engine inlet than the nominal, may be
creating higher component wear and in worst conditions damages to the equipment and
generate alarm signal at engine start, or even a load reduction request to PMS.
The surface temperature of the heater must not exceed 150°C in order to avoid cooking of
the oil.
The heaters should be provided with safety valves and drain pipes to a leakage tank (so that
possible leakage can be detected).
Separator (2S01)
The separators should preferably be of a type with controlled discharge of the bowl to minimize
the lubricating oil losses.
The service throughput Q [l/h] of the separator can be estimated with the formula:

where:
Q = volume flow [l/h]
P = engine output [kW]
n = 5 for HFO, 4 for MDF
t = operating time [h/day]: 24 for continuous separator operation, 23 for normal dimensioning
Sludge tank (2T06)

The sludge tank should be located directly beneath the separators, or as close as possible
below the separators, unless it is integrated in the separator unit. The sludge pipe must be
continuously falling.
7.2.2 System oil tank (2T01)

Recommended oil tank volume is stated in chapter Technical data.
The system oil tank is usually located beneath the engine foundation. The tank may not protrude
under the reduction gear or generator, and it must also be symmetrical in transverse direction
under the engine. The location must further be such that the lubricating oil is not cooled down
below normal operating temperature. Suction height is especially important with engine driven
lubricating oil pump. Losses in strainers etc. add to the geometric suction height. Maximum
suction ability of the pump is stated in chapter Technical data.
The pipe connection between the engine oil sump and the system oil tank must be flexible to
prevent damages due to thermal expansion. The return pipes from the engine oil sump must
end beneath the minimum oil level in the tank. Further on the return pipes must not be located
in the same corner of the tank as the suction pipe of the pump.
The suction pipe of the pump should have a trumpet shaped or conical inlet to minimise the
pressure loss. For the same reason the suction pipe shall be as short and straight as possible
and have a sufficient diameter. A pressure gauge shall be installed close to the inlet of the
lubricating oil pump. The suction pipe shall further be equipped with a non-return valve of flap
type without spring. The non-return valve is particularly important with engine driven pump
and it must be installed in such a position that self-closing is ensured.
Suction and return pipes of the separator must not be located close to each other in the tank.
The ventilation pipe from the system oil tank may not be combined with crankcase ventilation
pipes.
It must be possible to raise the oil temperature in the tank after a long stop. In cold conditions
it can be necessary to have heating coils in the oil tank in order to ensure pumpability. The
separator heater can normally be used to raise the oil temperature once the oil is pumpable.
Further heat can be transferred to the oil from the preheated engine, provided that the oil
viscosity and thus the power consumption of the pre-lubricating oil pump does not exceed
the capacity of the electric motor.

Fig 7-4 Example of system oil tank arrangement (DAAE007020e)
Design data:
Oil tank volume 1.2...1.5 l/kW, see also Technical data
Oil level at service 75...80% of tank volume
Oil level alarm 60% of tank volume
7.2.3 Suction strainers (2F01, 2F04, 2F06)

It is recommended to install a suction strainer before each pump to protect the pump from
damage. The suction strainer and the suction pipe must be amply dimensioned to minimize
pressure losses. The suction strainer should always be provided with alarm for high differential
pressure.
Design data:
Fineness 0.5...1.0 mm

7.2.4 Pre-lubricating oil pump (2P02)

The pre-lubricating oil pump is a scew or gear pump, which is to be equipped with a safety
valve.
The installation of a pre-lubricating pump is mandatory. An electrically driven main pump or
standby pump (with full pressure) may not be used instead of a dedicated pre-lubricating
pump, as the maximum permitted pressure is 200 kPa (2 bar) to avoid leakage through the
labyrinth seal in the turbocharger (not a problem when the engine is running). A two speed
electric motor for a main or standby pump is not accepted.
The piping shall be arranged so that the pre-lubricating oil pump fills the main oil pump, when
the main pump is engine driven.
The pre-lubricating pump should always be running, when the engine is stopped.
Depending on the foreseen oil temperature after a long stop, the suction ability of the pump
and the geometric suction height must be specially considered with regards to high viscosity.
With cold oil the pressure at the pump will reach the relief pressure of the safety valve.
Design data:
Capacity see Technical data
Max. pressure (safety valve) 350 kPa (3.5 bar)
Viscosity for dimensioning of the electric 500 cSt

motor
7.2.5 Pressure control valve (2V03)

Design data:
Capacity Difference between pump capacity and oil flow through engine
Design temperature 100 °C
7.2.6 Lubricating oil pump, stand-by (2P04)

The stand-by lubricating oil pump is normally of screw type and should be provided with an
safety valve.
Design data:
Capacity see Technical data
Design pressure, max 0.8 MPa (8 bar)
Design temperature, max. 100°C
Lubricating oil viscosity SAE 40
Viscosity for dimensioning the electric 500 mm2/s (cSt)

motor
7.3 Crankcase ventilation system

The purpose of the crankcase ventilation is to evacuate gases from the crankcase in order to
keep the pressure in the crankcase within acceptable limits.

Each engine must have its own vent pipe into open air. The crankcase ventilation pipes may
not be combined with other ventilation pipes, e.g. vent pipes from the system oil tank.
The diameter of the pipe shall be large enough to avoid excessive back pressure. Other possible
equipment in the piping must also be designed and dimensioned to avoid excessive flow
resistance.
A condensate trap must be fitted on the vent pipe near the engine.
The connection between engine and pipe is to be flexible.
Design data:
Flow see Technical data
Backpressure, max. see Technical data
Temperature 80°C
The size of the ventilation pipe (D2) out

from the condensate trap should be
equal or bigger than the ventilation pipe
(D) coming from the engine.
For more information about ventilation
pipe (D) size, see the external lubricating
oil system drawing.
The max. back-pressure must also be

considered when selecting the ventilation
pipe size.
Fig 7-5 Condensate trap
(DAAE032780B)

7.4 Flushing instructions

Flushing instructions in this Product Guide are for guidance only. For contracted projects,
read the specific instructions included in the installation planning instructions (IPI).
7.4.1 Piping and equipment built on the engine

Flushing of the piping and equipment built on the engine is not required and flushing oil shall
not be pumped through the engine oil system (which is flushed and clean from the factory).
It is however acceptable to circulate the flushing oil via the engine sump if this is advantageous.
Cleanliness of the oil sump shall be verified after completed flushing.
7.4.2 External oil system

Refer to the system diagram(s) in section External lubricating oil system for location/description
of the components mentioned below.
If the engine is equipped with a wet oil sump the external oil tanks, new oil tank (2T03),
renovating oil tank (2T04) and renovated oil tank (2T05) shall be verified to be clean before
bunkering oil. Especially pipes leading from the separator unit (2N01) directly to the engine
shall be ensured to be clean for instance by disconnecting from engine and blowing with
compressed air.
If the engine is equipped with a dry oil sump the external oil tanks, new oil tank and the system
oil tank (2T01) shall be verified to be clean before bunkering oil.
Operate the separator unit continuously during the flushing (not less than 24 hours). Leave
the separator running also after the flushing procedure, this to ensure that any remaining
contaminants are removed.
If an electric motor driven stand-by pump (2P04) is installed then piping shall be flushed running
the pump circulating engine oil through a temporary external oil filter (recommended mesh 34
microns) into the engine oil sump through a hose and a crankcase door. The pump shall be
protected by a suction strainer (2F06).
Whenever possible the separator unit shall be in operation during the flushing to remove dirt.
The separator unit is to be left running also after the flushing procedure, this to ensure that
any remaining contaminants are removed.
7.4.3 Type of flushing oil

7.4.3.1 Viscosity
In order for the flushing oil to be able to remove dirt and transport it with the flow, ideal viscosity
is 10...50 cSt. The correct viscosity can be achieved by heating engine oil to about 65°C or
by using a separate flushing oil which has an ideal viscosity in ambient temperature.
7.4.3.2 Flushing with engine oil

The ideal is to use engine oil for flushing. This requires however that the separator unit is in
operation to heat the oil. Engine oil used for flushing can be reused as engine oil provided that
no debris or other contamination is present in the oil at the end of flushing.
7.4.3.3 Flushing with low viscosity flushing oil

If no separator heating is available during the flushing procedure it is possible to use a low
viscosity flushing oil instead of engine oil. In such a case the low viscosity flushing oil must
be disposed of after completed flushing. Great care must be taken to drain all flushing oil from
pockets and bottom of tanks so that flushing oil remaining in the system will not compromise
the viscosity of the actual engine oil.

7.4.3.4 Lubricating oil sample

To verify the cleanliness a LO sample shall be taken by the shipyard after the flushing is
completed. The properties to be analyzed are Viscosity, BN, AN, Insolubles, Fe and Particle
Count.
Commissioning procedures shall in the meantime be continued without interruption unless
the commissioning engineer believes the oil is contaminated.

Wärtsilä 31 Product Guide 8. Compressed Air System
8. Compressed Air System

Compressed air is used to start engines and to provide actuating energy for safety and control
devices. The use of starting air for other purposes is limited by the classification regulations.
To ensure the functionality of the components in the compressed air system, the compressed
air has to be free from solid particles and oil.
8.1 Instrument air quality

The quality of instrument air, from the ships instrument air system, for safety and control
devices must fulfill the following requirements.
Instrument air specification:

Design pressure 1 MPa (10 bar)
Nominal pressure 0.7 MPa (7 bar)
Dew point temperature +3°C
Max. oil content 1 mg/m3
Max. particle size 3 µm
8.2 External compressed air system

The design of the starting air system is partly determined by classification regulations. Most
classification societies require that the total capacity is divided into two equally sized starting
air receivers and starting air compressors. The requirements concerning multiple engine
installations can be subject to special consideration by the classification society.
The starting air pipes should always be slightly inclined and equipped with manual or automatic
draining at the lowest points.
Instrument air to safety and control devices must be treated in an air dryer.

8. Compressed Air System Wärtsilä 31 Product Guide
Fig 8-1 External starting air system (DAAF301502)
System components: Pipe connections: Size
3E01 Cooler (Starting air compressor unit) 301 Starting air inlet DN32
3F02 Air filter (starting air inlet) 320 Instrument air inlet OD12
3N02 Starting air compressor unit
3N06 Air dryer unit
3P01 Compressor (starting air compressor unit)
3S01 Separator (starting air compressor unit)
3T01 Starting air vessel
8.2.1 Starting air compressor unit (3N02)

At least two starting air compressors must be installed. It is recommended that the compressors
are capable of filling the starting air vessel from minimum (1.8 MPa) to maximum pressure in
15...30 minutes. For exact determination of the minimum capacity, the rules of the classification
societies must be followed.
8.2.2 Oil and water separator (3S01)

An oil and water separator should always be installed in the pipe between the compressor
and the air vessel. Depending on the operation conditions of the installation, an oil and water
separator may be needed in the pipe between the air vessel and the engine.
8.2.3 Starting air vessel (3T01)

The starting air vessels should be dimensioned for a nominal pressure of 3 MPa.
The number and the capacity of the air vessels for propulsion engines depend on the
requirements of the classification societies and the type of installation.
It is recommended to use a minimum air pressure of 1.8 MPa, when calculating the required
volume of the vessels.

Wärtsilä 31 Product Guide 8. Compressed Air System
The starting air vessels are to be equipped with at least a manual valve for condensate drain.
If the air vessels are mounted horizontally, there must be an inclination of 3...5° towards the
drain valve to ensure efficient draining.
Size Dimensions [mm] Weight

[Litres] [kg]
L1 L2 1) L3 1) D
250 1767 243 110 480 274
500 3204 243 133 480 450
710 2740 255 133 650 625
1000 3560 255 133 650 810
1250 2930 255 133 800 980
1) Dimensions are approximate.
Fig 8-2 Starting air vessel
The starting air consumption stated in technical data is for a successful start. During start the
main starting valve is kept open until the engine starts, or until the max. time for the starting
attempt has elapsed. A failed start can consume two times the air volume stated in technical
data. If the ship has a class notation for unattended machinery spaces, then the starts are to
be demonstrated.
The required total starting air vessel volume can be calculated using the formula:
where:
VR = total starting air vessel volume [m3]
pE = normal barometric pressure (NTP condition) = 0.1 MPa
VE = air consumption per start [Nm3] See Technical data
n = required number of starts according to the classification society
pRmax = maximum starting air pressure = 3 MPa
pRmin = minimum starting air pressure = See Technical data

8. Compressed Air System Wärtsilä 31 Product Guide
NOTE
The total vessel volume shall be divided into at least two equally sized starting air
vessels.
8.2.4 Air filter, starting air inlet (3F02)

Condense formation after the water separator (between starting air compressor and starting
air vessels) create and loosen abrasive rust from the piping, fittings and receivers. Therefore
it is recommended to install a filter before the starting air inlet on the engine to prevent particles
to enter the starting air equipment.

Wärtsilä 31 Product Guide 9. Cooling Water System
9. Cooling Water System
9.1 Water quality

The fresh water in the cooling water system of the engine must fulfil the following requirements:
p H ............................... min. 6.5...8.5
Hardness ..................... max. 10 °dH
Chlorides ..................... max. 80 mg/l
Sulphates .................... max. 150 mg/l
Good quality tap water can be used, but shore water is not always suitable. It is recommended
to use water produced by an onboard evaporator. Fresh water produced by reverse osmosis
plants often has higher chloride content than permitted. Rain water is unsuitable as cooling
water due to the high content of oxygen and carbon dioxide.
Only treated fresh water containing approved corrosion inhibitors may be circulated through
the engines. It is important that water of acceptable quality and approved corrosion inhibitors
are used directly when the system is filled after completed installation.
9.1.1 Corrosion inhibitors

The use of an approved cooling water additive is mandatory. An updated list of approved
products is supplied for every installation and it can also be found in the Instruction manual
of the engine, together with dosage and further instructions.
9.1.2 Glycol
Use of glycol in the cooling water is not recommended unless it is absolutely necessary.
Starting from 20% glycol the engine is to be de-rated 0.23 % per 1% glycol in the water. Max.
60% glycol is permitted.
Corrosion inhibitors shall be used regardless of glycol in the cooling water.

9. Cooling Water System Wärtsilä 31 Product Guide
9.2 External cooling water system
Fig 9-1 Example diagram for single main engine (DAAF301503A)
System components:
4E03 Heat recovery (evaporator) 4P03 Stand-by pump (HT) 4S01 Air venting
4E05 Heater (preheating unit) 4P04 Circulating pump (preheater) 4T04 Drain tank
4E08 Central cooler 4P05 Stand-by pump (LT) 4T05 Expansion tank
4F01 Suction strainer (sea water) 4P09 Transfer pump 4V02 Temp. control valve (heat recovery)
4N01 Preheating unit 4P11 Circulating pump (sea water) 4V08 Temp. control valve (central cooler)
4N02 Evaporator unit 4P19 Circulating pump (evaporator) 4V09 Temp. control valve (charge air)
Pipe connections: 8V - 10V 12V - 14V 16V
401 HT-water inlet DN100 DN125 DN150
402 HT-water DN100 DN125 DN150
404 HT-water air vent OD12 OD12 OD12
406 Water from preheater to HT-circuit DN100 DN125 DN150
408 HT-water from stand-by pump DN100 DN125 DN150
416 HT-water airvent from air cooler OD12 OD12 OD12
451 LT-water inlet DN100 D125 DN150
452 LT-water outlet DN100 D125 DN150
457 LT-water from stand-by pump DN100 D125 DN150
483 LT-water air vent OD15 OD15 OD15

Fig 9-2 Example diagram for multiple main engines (DAAF301505A)
System components:
1E04 Cooler (MDF) 4P15 Circulating pump (LT)
4E03 Heat recovery (evaporator) 4P19 Circulating pump (evaporator)
4E05 Heater (preheater) 4S01 Air venting
4E08 Central cooler 4T04 Drain tank
4E15 Cooler (generator) 4T05 Expansion tank
4N01 Preheating unit 4V02 Temperature control valve (heat recovery)
4N02 Evaporator unit 4V08 Temperature control valve (central cooler)
4P04 Circulating pump (preheater) 4V09 Temperature control valve (charge air)
4P09 Transfer pump
Pipe connections: 8V-10V 12V-14V 16V
402 HT-water outlet DN100 DN125 DN150
451 LT-water inlet DN100 DN125 DN150
452 LT-water outlet DN100 DN125 DN150
460 LT-water to generator - - -
461 LT-water from generator - - -

Fig 9-3 Cooling water system, arctic solution for single main engines
(DAAF320499A)
System components:
1E04 Cooler (MDF) 4P05 Stand-by pump (LT)
4E05 Heater (preheater) 4P15 Circulating pump (LT)
4E08 Central cooler 4S01 Air venting
4E10 Cooler (reduction gear) 4T05 Expansion tank
4N01 Preheating unit 4V08 Temperature control valve (central cooler)
4P03 Stand-by pump (HT) 4V09 Temperature control valve (charge air)
4P04 Circulating pump (preheater)
408 HT-water from stand-by pump DN100 DN125 DN150
457 LT-water from stand-by pump DN100 DN125 DN150

Fig 9-4 Cooling water system, arctic solution for multiple engines (DAAF320500A)
System components:
1E04 Cooler (MDF) 4P15 Circulating pump (LT)
4E03 Heat recovery (evaporator) 4P19 Transfer pump
4E05 Heater (preheater) 4S01 Air venting
4E08 Central cooler 4T04 Drain tank
4E15 Cooler (generator) 4T05 Expansion tank
4N01 Preheating unit 4V02 Temperature control valve (heat recovery)
4N02 Evaporator unit 4V08 Temperature control valve (central cooler)
4P04 Circulating pump (preheater) 4V09 Temperature control valve (charge air)
4P09 Transfer pump
460 LT-water to generator - - -
461 LT-water from generator - - -

9.2.1 Cooling water system for arctic conditions

At low engine loads the combustion air can be below zero degrees Celsius after the compressor
stage, it cools down the cooling water and the engine instead of releasing heat to the cooling
water in the charge air cooler. If the combustion air temperature reaching the cylinders is too
cold, it can cause uneven burning of the fuel in the cylinder and possible misfires. Additionally
overcooling the engine jacket can cause cold corrosion of the cylinder liners or even a stuck
piston.
Thus maintaining nominal charge air receiver and HT-water inlet temperature are important
factors, when designing the cooling water system for arctic conditions. Proper receiver
temperatures must be ensured at all ambient temperatures. If needed, all charge air coolers
can be installed in the LT-circuit. LT-circuit heaters can also be used.
9.2.1.1 The arctic sea water cooling system

In arctic conditions, the hot sea water from the central cooler outlet is typically returned back
to the sea chest in order to prevent ice slush from blocking the sea water filters. An example
flow diagram of the arctic sea water system is shown in .
Fig 9-5 Example flow diagram of arctic sea water system
Ships (with ice class) designed for cold sea-water should have provisions for recirculation
back to the sea chest from the central cooler:
● For melting of ice and slush, to avoid clogging of the sea water strainer
● To enhance the temperature control of the LT water, by increasing the seawater temperature
It is recommended to divide the engines into several circuits in multi-engine installations. One
reason is of course redundancy, but it is also easier to tune the individual flows in a smaller
system. Malfunction due to entrained gases, or loss of cooling water in case of large leaks
can also be limited. In some installations it can be desirable to separate the HT circuit from
the LT circuit with a heat exchanger.
The external system shall be designed so that flows, pressures and temperatures are close
to the nominal values in Technical data and the cooling water is properly de-aerated.
Pipes with galvanized inner surfaces are not allowed in the fresh water cooling system. Some
cooling water additives react with zinc, forming harmful sludge. Zinc also becomes nobler
than iron at elevated temperatures, which causes severe corrosion of engine components.
9.2.2 Stand-by circulation pumps (4P03, 4P05)

Stand-by pumps should be of centrifugal type and electrically driven. Required capacities and
delivery pressures are stated in Technical data.

9.2.3 Sea water pump (4P11)

The sea water pumps are always separate from the engine and electrically driven.
The capacity of the pumps is determined by the type of coolers and the amount of heat to be
dissipated.
Significant energy savings can be achieved in most installations with frequency control of the
sea water pumps. Minimum flow velocity (fouling) and maximum sea water temperature (salt
deposits) are however issues to consider.
9.2.4 Temperature control valve for central cooler (4V08)

When it is desired to utilize the engine driven LT-pump for cooling of external equipment, e.g.
a reduction or a generator, there must be a common LT temperature control valve in the
external system, instead of an individual valve for each engine. The common LT temperature
control valve is installed after the central cooler and controls the temperature of the water
before the engine and the external equipment, by partly bypassing the central cooler. The
valve can be either direct acting or electrically actuated.
The set-point of the temperature control valve 4V08 is 38 ºC in the type of system described
above.
Engines operating on HFO must have individual LT temperature control valves. A separate
pump is required for the external equipment in such case, and the set-point of 4V08 can be
lower than 38 ºC if necessary.
9.2.5 Charge air temperature control valve (4V09)

The temperature of the charge air is maintained on desired level with an electrically actuated
temperature control valve in the external LT circuit. The control valve regulates the water flow
through the LT-stage of the charge air cooler according to the measured temperature in the
charge air receiver.
9.2.6 Temperature control valve for heat recovery (4V02)

The temperature control valve after the heat recovery controls the maximum temperature of
the water that is mixed with HT water from the engine outlet before the HT pump. The control
valve can be either self-actuated or electrically actuated.
Especially in installations with dynamic positioning (DP) feature, installation of valve 4V02 is
strongly recommended in order to avoid HT temperature fluctuations during low load operation.
The set-point is usually somewhere close to 75 ºC.
9.2.7 Coolers for other equipment and MDF coolers

The engine driven LT circulating pump can supply cooling water to one or two small coolers
installed in parallel to the engine, for example a MDF cooler or a reduction gear cooler. This
is only possible for engines operating on MDF, because the LT temperature control valve
cannot be built on the engine to control the temperature after the engine. Separate circulating
pumps are required for larger flows.
Design guidelines for the MDF cooler are given in chapter Fuel system.
9.2.8 Fresh water central cooler (4E08)

The flow to the fresh water cooler must be calculated case by case based on how the circuit
is designed.
In case the fresh water central cooler is used for combined LT and HT water flows in a parallel
system the total flow can be calculated with the following formula:

where:
q = total fresh water flow [m³/h]
qLT = nominal LT pump capacity[m³/h]
Φ = heat dissipated to HT water [kW]
Tout = HT water temperature after engine (91°C)
Tin = HT water temperature after cooler (38°C)
Design data:
Fresh water flow see chapter Technical Data
Heat to be dissipated see chapter Technical Data
Pressure drop on fresh water side max. 60 kPa (0.6 bar)
Sea-water flow acc. to cooler manufacturer, normally 1.2 - 1.5 x the fresh
water flow
Pressure drop on sea-water side, norm. acc. to pump head, normally 80 - 140 kPa (0.8 - 1.4 bar)
Fresh water temperature after cooler max. 38°C
Margin (heat rate, fouling) 15%
As an alternative to central coolers of plate or tube type, a box cooler can be installed. The
principle of box cooling is very simple. Cooling water is forced through a U-tube-bundle, which
is placed in a sea-chest having inlet- and outlet-grids. Cooling effect is reached by natural
circulation of the surrounding water. The outboard water is warmed up and rises by its lower
density, thus causing a natural upward circulation flow which removes the heat.
Box cooling has the advantage that no raw water system is needed, and box coolers are less
sensitive for fouling and therefor well suited for shallow or muddy waters.
9.2.9 Waste heat recovery

The waste heat in the HT cooling water can be used for fresh water production, central heating,
tank heating etc. The system should in such case be provided with a temperature control
valve to avoid unnecessary cooling, as shown in the example diagrams. With this arrangement
the HT water flow through the heat recovery can be increased.
The heat available from HT cooling water is affected by ambient conditions. It should also be
taken into account that the recoverable heat is reduced by circulation to the expansion tank,
radiation from piping and leakages in temperature control valves.
9.2.10 Air venting

Air may be entrained in the system after an overhaul, or a leak may continuously add air or
gas into the system. The engine is equipped with vent pipes to evacuate air from the cooling
water circuits. The vent pipes should be drawn separately to the expansion tank from each
connection on the engine, except for the vent pipes from the charge air cooler on V-engines,
which may be connected to the corresponding line on the opposite cylinder bank.
Venting pipes to the expansion tank are to be installed at all high points in the piping system,
where air or gas can accumulate.

The vent pipes must be continuously rising.
9.2.11 Expansion tank (4T05)

The expansion tank compensates for thermal expansion of the coolant, serves for venting of
the circuits and provides a sufficient static pressure for the circulating pumps.
Design data:
Volume min. 10% of the total system volume
NOTE
The maximum pressure at the engine must not be exceeded in case an electrically
driven pump is installed significantly higher than the engine.
Concerning the water volume in the engine, see chapter Technical data.
The expansion tank should be equipped with an inspection hatch, a level gauge, a low level
alarm and necessary means for dosing of cooling water additives.
The vent pipes should enter the tank below the water level. The vent pipes must be drawn
separately to the tank (see air venting) and the pipes should be provided with labels at the
expansion tank.
The balance pipe down from the expansion tank must be dimensioned for a flow velocity not
exceeding 1.0...1.5 m/s in order to ensure the required pressure at the pump inlet with engines
running. The flow through the pipe depends on the number of vent pipes to the tank and the
size of the orifices in the vent pipes. The table below can be used for guidance.
Table 9-1 Minimum diameter of balance pipe
Nominal pipe size Max. flow velocity (m/s) Max. number of vent pipes
with ø 5 mm orifice
DN 32 1.1 3
DN 40 1.2 6
DN 50 1.3 10
DN 65 1.4 17
9.2.12 Drain tank (4T04)

It is recommended to collect the cooling water with additives in a drain tank, when the system
has to be drained for maintenance work. A pump should be provided so that the cooling water
can be pumped back into the system and reused.
Concerning the water volume in the engine, see chapter Technical data. The water volume in
the LT circuit of the engine is small.
9.2.13 Preheating
The cooling water circulating through the cylinders must be preheated to at least 60 ºC,
preferably 70 ºC. This is an absolute requirement for installations that are designed to operate
on heavy fuel, but strongly recommended also for engines that operate exclusively on marine
diesel fuel.
The energy required for preheating of the HT cooling water can be supplied by a separate
source or by a running engine, often a combination of both. In all cases a separate circulating
pump must be used. It is common to use the heat from running auxiliary engines for preheating

of main engines. In installations with several main engines the capacity of the separate heat
source can be dimensioned for preheating of two engines, provided that this is acceptable
for the operation of the ship. If the cooling water circuits are separated from each other, the
energy is transferred over a heat exchanger.
9.2.13.1 Heater (4E05)

The energy source of the heater can be electric power, steam or thermal oil.
It is recommended to heat the HT water to a temperature near the normal operating
temperature. The heating power determines the required time to heat up the engine from cold
condition.
The minimum required heating power is 5 kW/cyl, which makes it possible to warm up the
engine from 20 ºC to 60...70 ºC in 10-15 hours. The required heating power for shorter heating
time can be estimated with the formula below. About 2 kW/cyl is required to keep a hot engine
warm.
Design data:
Preheating temperature min. 60°C
Required heating power 5 kW/cyl
Heating power to keep hot engine warm 2 kW/cyl
Required heating power to heat up the engine, see formula below:
where:
P = Preheater output [kW]
T1 = Preheating temperature = 60...70 °C
T0 = Ambient temperature [°C]
meng = Engine weight [ton]
VLO = Lubricating oil volume [m3] (wet sump engines only)
VFW = HT water volume [m3]
t = Preheating time [h]

keng = Engine specific coefficient = 1 kW
ncyl = Number of cylinders
9.2.13.2 Circulation pump for preheater (4P04)

Design data:
Delivery pressure 80...100 kPa (0.8...1.0 bar)
9.2.13.3 Preheating unit (4N01)

A complete preheating unit can be supplied. The unit comprises:
● Electric or steam heaters
● Circulating pump
● Control cabinet for heaters and pump
● Set of thermometers
● Non-return valve

● Safety valve
Fig 9-6 Preheating unit, electric (3V60L0562C).
Heater capacity Pump capacity Weight Pipe conn. Dimensions [mm]

[kW] [m³/h] [kg]
50 Hz 60 HZ In/outlet A B C D E
18 11 13 95 DN40 1250 900 660 240 460
22.5 11 13 100 DN40 1050 720 700 290 480
27 12 13 103 DN40 1250 900 700 290 480
30 12 13 105 DN40 1050 720 700 290 480
36 12 13 125 DN40 1250 900 700 290 480
45 12 13 145 DN40 1250 720 755 350 510
54 12 13 150 DN40 1250 900 755 350 510
72 12 13 187 DN40 1260 900 805 400 550
81 12 13 190 DN40 1260 900 805 400 550
108 12 13 215 DN40 1260 900 855 450 575
9.2.14 Throttles
Throttles (orifices) are to be installed in all by-pass lines to ensure balanced operating conditions
for temperature control valves. Throttles must also be installed wherever it is necessary to
balance the waterflow between alternate flow paths.
9.2.15 Thermometers and pressure gauges

Local thermometers should be installed wherever there is a temperature change, i.e. before
and after heat exchangers etc.
Local pressure gauges should be installed on the suction and discharge side of each pump.

Wärtsilä 31 Product Guide 10. Combustion Air System
10. Combustion Air System

The engine draws the combustion air either from the engine room through the inlet filter fitted
on the turbocharger or from outside of the engine room. In case air is taken from inside of the
engine room, the combustion air should be delivered through a dedicated duct close to the
turbochargers, directed towards the air intakes. For the required amount of combustion air
and the heat emitted by the engine is listed in chapter 3. Technical Data.
10.1 Engine room ventilation

To maintain acceptable operating conditions for the engines and to ensure trouble free operation
of all equipment, attention shall be paid to the engine room ventilation and the supply of
combustion air.
The air intakes to the engine room must be located and designed so that water spray, rain
water, dust and exhaust gases cannot enter the ventilation ducts and the engine room.
The dimensioning of blowers and extractors should ensure that an overpressure of about 50
Pa is maintained in the engine room in all running conditions.
During normal operating conditions the air temperature at the turbocharger inlet should be
kept between 15ºC and 35ºC. Max. 45ºC is allowed.
For the minimum requirements concerning the engine room ventilation and more details, see
applicable standards, such as ISO 8861.
The amount of air required for ventilation is calculated from the total heat emission Φ to
evacuate. To determine Φ, all heat sources shall be considered, e.g.:
● Main and auxiliary diesel engines
● Exhaust gas piping
● Generators
● Electric appliances and lighting
● Boilers
● Steam and condensate piping
● Tanks
● Other auxiliary equipment
It is recommended to consider an outside air temperature of no less than 35°C and a
temperature rise of 11°C for the ventilation air.
The amount of air required for ventilation is then calculated using the formula:
where:
air flow [m³/s]

qv =
Φ = total heat emission to be evacuated [kW]
ρ = air density 1.13 kg/m³
c = specific heat capacity of the ventilation air 1.01 kJ/kgK

10. Combustion Air System Wärtsilä 31 Product Guide
ΔT = temperature rise in the engine room [°C]
The heat emitted by the engine is listed in chapter Technical data.

The engine room ventilation air has to be provided by separate ventilation fans. These fans
should preferably have two-speed electric motors (or variable speed). The ventilation can then
be reduced according to outside air temperature and heat generation in the engine room, for
example during overhaul of the main engine when it is not preheated (and therefore not heating
the room).
The ventilation air is to be equally distributed in the engine room considering air flows from
points of delivery towards the exits. This is usually done so that the funnel serves as exit for
most of the air. To avoid stagnant air, extractors can be used.
It is good practice to provide areas with significant heat sources, such as separator rooms
with their own air supply and extractors.
Under-cooling of the engine room should be avoided during all conditions (service conditions,
slow steaming and in port). Cold draft in the engine room should also be avoided, especially
in areas of frequent maintenance activities. For very cold conditions a pre-heater in the system
should be considered. Suitable media could be thermal oil or water/glycol to avoid the risk
for freezing. If steam is specified as heating medium for the ship, the pre-heater should be in
a secondary circuit.
Fig 10-1 Engine room ventilation, turbocharger with air filter (DAAF391752)

Wärtsilä 31 Product Guide 10. Combustion Air System
Fig 10-2 Engine room ventilation, air duct connected to the turbocharger
(DAAF391711)
10.2 Combustion air system design

Usually, the combustion air is taken from the engine room through a filter on the turbocharger.
This reduces the risk for too low temperatures and contamination of the combustion air. It is
important that the combustion air is free from sea water, dust, fumes, etc.
For the required amount of combustion air, see section Technical data.
The combustion air shall be supplied by separate combustion air fans, with a capacity slightly
higher than the maximum air consumption. The combustion air mass flow stated in technical
data is defined for an ambient air temperature of 25°C. Calculate with an air density
corresponding to 30°C or more when translating the mass flow into volume flow. The expression
below can be used to calculate the volume flow.
where:
qc = combustion air volume flow [m³/s]
m' = combustion air mass flow [kg/s]
ρ = air density 1.15 kg/m³
The fans should preferably have two-speed electric motors (or variable speed) for enhanced
flexibility. In addition to manual control, the fan speed can be controlled by engine load.
In multi-engine installations each main engine should preferably have its own combustion air
fan. Thus the air flow can be adapted to the number of engines in operation.
The combustion air should be delivered through a dedicated duct close to the turbocharger,
directed towards the turbocharger air intake. The outlet of the duct should be equipped with
a flap for controlling the direction and amount of air. Also other combustion air consumers,
for example other engines, gas turbines and boilers shall be served by dedicated combustion
air ducts.
If necessary, the combustion air duct can be connected directly to the turbocharger with a
flexible connection piece. With this arrangement an external filter must be installed in the duct
to protect the turbocharger and prevent fouling of the charge air cooler. The permissible total

10. Combustion Air System Wärtsilä 31 Product Guide
pressure drop in the duct is max. 1.5 kPa. The duct should be provided with a step-less
change-over flap to take the air from the engine room or from outside depending on engine
load and air temperature.
For very cold conditions arctic setup is to be used. The combustion air fan is stopped during
start of the engine and the necessary combustion air is drawn from the engine room. After
start either the ventilation air supply, or the combustion air supply, or both in combination
must be able to maintain the minimum required combustion air temperature. The air supply
from the combustion air fan is to be directed away from the engine, when the intake air is cold,
so that the air is allowed to heat up in the engine room.
10.2.1 Charge air shut-off valve (optional)

In installations where it is possible that the combustion air includes combustible gas or vapour
the engines can be equipped with charge air shut-off valve. This is regulated mandatory where
ingestion of flammable gas or fume is possible.
10.2.2 Condensation in charge air coolers

Air humidity may condense in the charge air cooler, especially in tropical conditions. The
engine is equipped with an active dewpoint control to minimize condensation in the charge
air coolers and -receiver, by raising the LT-cooling water temperature based on ambient
humidity and charge air pressure. The engine is also equipped with a small drain pipe from
the charge air cooler and receiver for possible condensed water. Humidity sensor is mounted
in external system.

Wärtsilä 31 Product Guide 11. Exhaust Gas System
11. Exhaust Gas System
11.1 Exhaust gas outlet
TC location
Engine
Free end Driving end
W 8V31
0º, 45º, 90º 0º, 45º, 90º
W 10V31
Fig 11-1 Exhaust pipe connections, W8V31 &

W10V31 (DAAF343596A)
TC location
Engine
Free end Driving end
W 12V31
W 14V31 0º, 45º 0º, 45º
W 16V31
Fig 11-2 Exhaust pipe connections, W12V -

W16V31 (DAAF343596A)
NOTE
Pipe Connection 501 Exhaust Gas Outlet DIN86044, PN 6

11. Exhaust Gas System Wärtsilä 31 Product Guide
Engine ØA [mm] ØB [mm]
W 8V31 DN550 700
W DN550 800
10V31
Fig 11-3 Exhaust pipe, diameters and support

(DAAF351047)
Engine ØA [mm] ØB [mm]
W DN450 900
12V31
W DN450 900
14V31
W DN450 1000
16V31
Fig 11-4 Exhaust pipe, diameters and support

(DAAF351275A, DAAF351507A)

11.2 External exhaust gas system

Each engine should have its own exhaust pipe into open air. Backpressure, thermal expansion
and supporting are some of the decisive design factors.
Flexible bellows must be installed directly on the turbocharger outlet, to compensate for
thermal expansion and prevent damages to the turbocharger due to vibrations.
1 Engine
2 Exhaust gas bellows
3 Transitions piece
4 Not applicable for Wärtsilä 31 Diesel Engines
5 Connection for measurement of back pressure
6 Drain with water trap, continuosuly open
7 Bilge
8 Not applicable for Wärtsilä 31 Diesel Engines
9 Selective Catalytic Reactor (SCR)
10 Urea injection unit (SCR)
Fig 11-5 External exhaust gas 11a Silencer with spark arrestor
system (DAAF391527) 11b CSS silencer element
11.2.1 Piping
The piping should be as short and straight as possible. Pipe bends and expansions should
be smooth to minimise the backpressure. The diameter of the exhaust pipe should be increased
directly after the bellows on the turbocharger. Pipe bends should be made with the largest
possible bending radius; the bending radius should not be smaller than 1.5 x D.
The recommended flow velocity in the pipe is maximum 35…40 m/s at full output. If there are
many resistance factors in the piping, or the pipe is very long, then the flow velocity needs to
be lower. The exhaust gas mass flow given in chapter Technical data can be translated to
velocity using the formula:
where:
v = gas velocity [m/s]
m' = exhaust gas mass flow [kg/s]
T = exhaust gas temperature [°C]
D = exhaust gas pipe diameter [m]
The exhaust pipe must be insulated with insulation material approved for concerned operation
conditions, minimum thickness 30 mm considering the shape of engine mounted insulation.

Insulation has to be continuous and protected by a covering plate or similar to keep the
insulation intact.
Closest to the turbocharger the insulation should consist of a hook on padding to facilitate
maintenance. It is especially important to prevent the airstream to the turbocharger from
detaching insulation, which will clog the filters.
After the insulation work has been finished, it has to be verified that it fulfils SOLAS-regulations.
Surface temperatures must be below 220°C on whole engine operating range.
11.2.2 Supporting
It is very important that the exhaust pipe is properly fixed to a support that is rigid in all
directions directly after the bellows on the turbocharger. There should be a fixing point on
both sides of the pipe at the support. The bellows on the turbocharger may not be used to
absorb thermal expansion from the exhaust pipe. The first fixing point must direct the thermal
expansion away from the engine. The following support must prevent the pipe from pivoting
around the first fixing point.
Absolutely rigid mounting between the pipe and the support is recommended at the first fixing
point after the turbocharger. Resilient mounts can be accepted for resiliently mounted engines
with “double” variant bellows (bellow capable of handling the additional movement), provided
that the mounts are self-captive; maximum deflection at total failure being less than 2 mm
radial and 4 mm axial with regards to the bellows. The natural frequencies of the mounting
should be on a safe distance from the running speed, the firing frequency of the engine and
the blade passing frequency of the propeller. The resilient mounts can be rubber mounts of
conical type, or high damping stainless steel wire pads. Adequate thermal insulation must be
provided to protect rubber mounts from high temperatures. When using resilient mounting,
the alignment of the exhaust bellows must be checked on a regular basis and corrected when
necessary.
After the first fixing point resilient mounts are recommended. The mounting supports should
be positioned at stiffened locations within the ship’s structure, e.g. deck levels, frame webs
or specially constructed supports.
The supporting must allow thermal expansion and ship’s structural deflections.
11.2.3 Back pressure

The maximum permissible exhaust gas back pressure is stated in chapter Technical Data. The
back pressure in the system must be calculated by the shipyard based on the actual piping
design and the resistance of the components in the exhaust system. The exhaust gas mass
flow and temperature given in chapter Technical Data may be used for the calculation.
Each exhaust pipe should be provided with a connection for measurement of the back pressure.
The back pressure must be measured by the shipyard during the sea trial.
11.2.4 Exhaust gas bellows (5H01, 5H03)

Bellows must be used in the exhaust gas piping where thermal expansion or ship’s structural
deflections have to be segregated. The flexible bellows mounted directly on the turbocharger
outlet serves to minimise the external forces on the turbocharger and thus prevent excessive
vibrations and possible damage. All exhaust gas bellows must be of an approved type.
11.2.5 SCR-unit (11N14)

The SCR-unit requires special arrangement on the engine in order to keep the exhaust gas
temperature and backpressure into SCR-unit working range. The exhaust gas piping must be
straight at least 3...5 meters in front of the SCR unit. If both an exhaust gas boiler and a SCR
unit will be installed, then the exhaust gas boiler shall be installed after the SCR. Arrangements
must be made to ensure that water cannot spill down into the SCR, when the exhaust boiler
is cleaned with water.

More information about the SCR-unit can be found in the Wärtsilä Environmental Product
Guide.
11.2.6 Exhaust gas boiler

If exhaust gas boilers are installed, each engine should have a separate exhaust gas boiler.
Alternatively, a common boiler with separate gas sections for each engine is acceptable.
For dimensioning the boiler, the exhaust gas quantities and temperatures given in chapter
Technical data may be used.

11.2.7 Exhaust gas silencers

The exhaust gas silencing can be accomplished either by the patented Compact Silencer
System (CSS) technology or by the conventional exhaust gas silencer.
11.2.7.1 Exhaust noise

The unattenuated exhaust noise is typically measured in the exhaust duct. The in-duct
measurement is transformed into free field sound power through a number of correction
factors.
The spectrum of the required attenuation in the exhaust system is achieved when the free
field sound power (A) is transferred into sound pressure (B) at a certain point and compared
with the allowable sound pressure level (C).
Fig 11-6 Exhaust noise, source power corrections
The conventional silencer is able to reduce the sound level in a certain area of the frequency
spectrum. CSS is designed to cover the whole frequency spectrum.

11.2.7.2 Silencer system comparison

With a conventional silencer system, the design of the noise reduction system usually starts
from the engine. With the CSS, the design is reversed, meaning that the noise level acceptability
at a certain distance from the ship's exhaust gas pipe outlet, is used to dimension the noise
reduction system.
Fig 11-7 Silencer system comparison
11.2.7.3 Compact silencer system (5N02)

The CSS system is optimized for each installation as a complete exhaust gas system. The
optimization is made according to the engine characteristics, to the sound level requirements
and to other equipment installed in the exhaust gas system, like SCR, exhaust gas boiler or
scrubbers.
The CSS system is built up of three different CSS elements; resistive, reactive and composite
elements. The combination-, amount- and length of the elements are always installation
specific. The diameter of the CSS element is 1.4 times the exhaust gas pipe diameter.
The noise attenuation is valid up to a exhaust gas flow velocity of max 40 m/s. The pressure
drop of a CSS element is lower compared to a conventional exhaust gas silencer (5R02).

11.2.7.4 Conventional exhaust gas silencer (5R02)

Yard/designer should take into account that unfavourable layout of the exhaust system (length
of straight parts in the exhaust system) might cause amplification of the exhaust noise between
engine outlet and the silencer. Hence the attenuation of the silencer does not give any absolute
guarantee for the noise level after the silencer.
When included in the scope of supply, the standard silencer is of the absorption type, equipped
with a spark arrester. It is also provided with a soot collector and a condense drain, but it
comes without mounting brackets and insulation. The silencer can be mounted either
horizontally or vertically.
The noise attenuation of the standard silencer is either 25 or 35 dB(A). This attenuation is valid
up to a flow velocity of max. 40 m/s.

Wärtsilä 31 Product Guide 12. Turbocharger Cleaning
12. Turbocharger Cleaning

Regular water cleaning of the turbine and the compressor reduces the formation of deposits
and extends the time between overhauls. Fresh water is injected into the turbocharger during
operation. Additives, solvents or salt water must not be used and the cleaning instructions in
the operation manual must be carefully followed.
12.1 Turbine cleaning system

A dosing unit consisting of a flow meter and an adjustable throttle valve is delivered for each
installation. The dosing unit is installed in the engine room and connected to the engine with
a detachable rubber hose. The rubber hose is connected with quick couplings and the length
of the hose is normally 10 m. One dosing unit can be used for several engines.
Water supply:
Fresh water
Min. pressure 0.3 MPa (3 bar)
Max. pressure 2 MPa (20 bar)
Max. temperature 80 °C
Fig 12-1 Turbocharger cleaning system (DAAF347567)
System components Pipe connections
5Z03 TC cleaning device 502## Cleaning water to turbine
02 Wärtsilä control unit for 4 engines 509## Cleaning water to compressor
03 Flow meter/control (7,5 - 40 l/min) 614## Scavenging air outlet to TC cleaning valve unit
04 Flow adjustment valve, built in
05 Air filter

12. Turbocharger Cleaning Wärtsilä 31 Product Guide
Engine Water
Turbine / compressor Water inlet flow rate (l/min) Water consumption/wash (l)
LP-compressor 6.5 1
LP-turbine 18 180
HP-compressor 6.5 1
HP-turbine 22 220
12.2 Compressor cleaning system

The compressor side of the turbocharger is cleaned with the same equipment as the turbine.

Wärtsilä 31 Product Guide 13. Exhaust Emissions
13. Exhaust Emissions

Exhaust emissions from the diesel engine mainly consist of nitrogen, oxygen and combustion
products like carbon dioxide (CO2), water vapour and minor quantities of carbon monoxide
(CO), sulphur oxides (SOx), nitrogen oxides (NOx), partially reacted and non-combusted
hydrocarbons (HC) and particulate matter (PM).
There are different emission control methods depending on the aimed pollutant. These are
mainly divided in two categories; primary methods that are applied on the engine itself and
secondary methods that are applied on the exhaust gas stream.
13.1 Diesel engine exhaust components

The nitrogen and oxygen in the exhaust gas are the main components of the intake air which
don't take part in the combustion process.
CO2 and water are the main combustion products. Secondary combustion products are carbon
monoxide, hydrocarbons, nitrogen oxides, sulphur oxides, soot and particulate matters.
In a diesel engine the emission of carbon monoxide and hydrocarbons are low compared to
other internal combustion engines, thanks to the high air/fuel ratio in the combustion process.
The air excess allows an almost complete combustion of the HC and oxidation of the CO to
CO2, hence their quantity in the exhaust gas stream are very low.
13.1.1 Nitrogen oxides (NOx)

The combustion process gives secondary products as Nitrogen oxides. At high temperature
the nitrogen, usually inert, react with oxygen to form Nitric oxide (NO) and Nitrogen dioxide
(NO2), which are usually grouped together as NOx emissions. Their amount is strictly related
to the combustion temperature.
NO can also be formed through oxidation of the nitrogen in fuel and through chemical reactions
with fuel radicals. NO in the exhaust gas flow is in a high temperature and high oxygen
concentration environment, hence oxidizes rapidly to NO2. The amount of NO2 emissions is
approximately 5 % of total NOx emissions.
13.1.2 Sulphur Oxides (SOx)

Sulphur oxides (SOx) are direct result of the sulphur content of the fuel oil. During the
combustion process the fuel bound sulphur is rapidly oxidized to sulphur dioxide (SO2). A
small fraction of SO2 may be further oxidized to sulphur trioxide (SO3).
13.1.3 Particulate Matter (PM)

The particulate fraction of the exhaust emissions represents a complex mixture of inorganic
and organic substances mainly comprising soot (elemental carbon), fuel oil ash (together with
sulphates and associated water), nitrates, carbonates and a variety of non or partially
combusted hydrocarbon components of the fuel and lubricating oil.
13.1.4 Smoke
Although smoke is usually the visible indication of particulates in the exhaust, the correlations
between particulate emissions and smoke is not fixed. The lighter and more volatile
hydrocarbons will not be visible nor will the particulates emitted from a well maintained and
operated diesel engine.

13. Exhaust Emissions Wärtsilä 31 Product Guide
Smoke can be black, blue, white, yellow or brown in appearance. Black smoke is mainly
comprised of carbon particulates (soot). Blue smoke indicates the presence of the products
of the incomplete combustion of the fuel or lubricating oil. White smoke is usually condensed
water vapour. Yellow smoke is caused by NOx emissions. When the exhaust gas is cooled
significantly prior to discharge to the atmosphere, the condensed NO2 component can have
a brown appearance.
13.2 Marine exhaust emissions legislation

13.2.1 International Maritime Organization (IMO)
The increasing concern over the air pollution has resulted in the introduction of exhaust
emission controls to the marine industry. To avoid the growth of uncoordinated regulations,
the IMO (International Maritime Organization) has developed the Annex VI of MARPOL 73/78,
which represents the first set of regulations on the marine exhaust emissions.
The IMO Tier 3 NOx emission standard will enter into force from year 2016. It will by then apply
for new marine diesel engines that:
● Are > 130 kW
● Installed in ships which keel laying date is 1.1.2016 or later
● Operating inside the North American ECA and the US Caribbean Sea ECA
From 1.1.2021 onwards Baltic sea and North sea will be included in to IMO Tier 3 NOx
requirements.
13.2.2 Other Legislations

There are also other local legislations in force in particular regions.
13.3 Methods to reduce exhaust emissions

All standard Wärtsilä engines meet the NOx emission level set by the IMO (International Maritime
Organisation) and most of the local emission levels without any modifications. Wärtsilä has
also developed solutions to significantly reduce NOx emissions when this is required.
Diesel engine exhaust emissions can be reduced either with primary or secondary methods.
The primary methods limit the formation of specific emissions during the combustion process.
The secondary methods reduce emission components after formation as they pass through
the exhaust gas system.
Refer to the "Wärtsilä Environmental Product Guide" for information about exhaust gas emission
control systems.

Wärtsilä 31 Product Guide 14. Automation System
14. Automation System

Wärtsilä Unified Controls - UNIC is a fully embedded and distributed engine management
system, which handles all control functions on the engine; for example start sequencing, start
blocking, fuel injection, cylinder balancing, knock control, speed control, load sharing, normal
stops and safety shutdowns.
The distributed modules communicate over an internal communication bus.
The power supply to each module is physically doubled on the engine for full redundancy.
Control signals to/from external systems are hardwired to the terminals in the main cabinet
on the engine. Process data for alarm and monitoring are communicated over a Modbus TCP
connection to external systems.
14.1 Technical data and system overview

14.1.1 Ingress protection
The ingress protection class of the system is IP54.
14.1.2 Ambient temp for automation system

The system design and implementation of the engine allows for an ambient engine room
temperature of 55°C.
Single components such as electronic modules have a temperature rating not less than 70°C.
Fig 14-1 Architecture of UNIC

14. Automation System Wärtsilä 31 Product Guide
Fig 14-2 UNIC overview MS applications
Short explanation of the modules used in the system:
COM Communication Module. Handles strategic control functions (such as start/stop sequen-
cing and speed/load control, i.e. "speed governing") of the engine.
The communication modules handle engine internal and external communication, as
well as hardwired external interfaces.
ESM Engine Safety Module handles fundamental engine safety, for example shutdown due
to overspeed or low lubricating oil pressure.
LOP The LOP (local operator panel) shows all engine measurements (e.g. temperatures and
pressures) and provides various engine status indications as well as an event history.
IOM Input/Output Module handles measurements and limited control functions in a specific
area on the engine.
CCM Cylinder Control Module handles fuel injection control and local measurements for the
cylinders.
The above equipment and instrumentation are prewired on the engine.
14.1.3 Local operator panel

● The Local operator panel (LOP) consist of a display unit with touch screen and pushbuttons
as well as an emergency stop button built on the engine.
The local operator panel shows all engine measurements (e.g. temperatures and pressures)
and provides various engine status indications as well as an event history

The following control functions are available:

- Local/remote control selection
- Local start & stop
- Trip & Shutdown reset
- Emergency stop
● Local emergency speed setting (mechanical propulsion):
● Local emergency stop
Fig 14-3 Local operator panel
14.1.4 Engine safety system

The engine safety module handles fundamental safety functions, for example overspeed
protection.
Main features:
● Redundant design for power supply, speed inputs and stop solenoid control
● Fault detection on sensors, solenoids and wires
● Led indication of status and detected faults
● Digital status outputs
● Shutdown latching and reset
● Shutdown pre-warning
● Shutdown override (configuration depending on application)
14.1.5 Power unit

A power unit is delivered with each engine. The power unit supplies DC power to the automation
system on the engine and provides isolation from other power supply systems onboard. The
cabinet is designed for bulkhead mounting, protection degree IP44, max. ambient temperature
50°C.

The power unit contains redundant power converters, each converter dimensioned for 100%
load. At least one of the two incoming supplies must be connected to a UPS. The power unit
supplies the automation system on the engine with 24 VDC and 110 VDC.
Power supply from ship's system:
● Supply 1: 230 VAC / abt. 750 W
● Supply 2: 230 VAC / abt. 750 W
14.1.6 Ethernet communication unit

Ethernet switch and firewall/router are installed in a steel sheet cabinet for bulkhead mounting,
protection class IP44.
14.1.7 Cabling and system overview
Fig 14-4 UNIC overview
Table 14-1 Typical amount of cables
Cable From <=> To Cable types (typical)
A Engine <=> Power Unit 2 x 4 mm2 (power supply) *

2 x 4 mm2 (power supply) *
B Power unit => Communication interface unit 2 x 2.5 mm2 (power supply) *

Cable From <=> To Cable types (typical)
C Engine <=> Propulsion Control System 1 x 2 x 0.75 mm2

Engine <=> Power Management System / Main Switch- 1 x 2 x 0.75 mm2
board 1 x 2 x 0.75 mm2
24 x 0.75 mm2
24 x 0.75 mm2
D Power unit <=> Integrated Automation System 2 x 0.75 mm2
E Engine <=> Integrated Automation System 3 x 2 x 0.75 mm2
F Engine => Communication interface unit 1 x Ethernet CAT 5
G Communication interface unit => Integrated automation 1 x Ethernet CAT 5

system
H Engine => Pre-lubrication pump starter 2 x 0.75 mm2
I Engine => Turning gear starter 1 x CAN bus (120 ohm)
NOTE
Cable types and grouping of signals in different cables will differ depending on
installation.
* Dimension of the power supply cables depends on the cable length.
Power supply requirements are specified in section Power unit.
Fig 14-5 Signal overview (Main engine)

Fig 14-6 Signal overview (Generating set)
14.2 Functions
14.2.1 Start
The engine is started by injecting compressed air directly into the cylinders.
The engine can be started locally, or remotely if applicable for the installation e.g. from the
power management system or control room. In an emergency situation it is also possible to
operate the starting air valve manually.
Starting is blocked both pneumatically and electrically when the turning gear is engaged.
The engine is equipped with a slow turning system, which rotates the engine without fuel
injection for a few turns before start. Slow turning is performed automatically at predefined
intervals, if the engine has been selected as stand-by.
14.2.1.1 Startblockings
Starting is inhibited by the following functions:
● Turning gear engaged
● Pre-lubricating pressure low
● Blocked by operator from the local operator panel
● Stop or shutdown active
● External start blockings active
● Engine running

14.2.2 Stop and shutdown

A normal stop can be initiated locally, or remotely if applicable for the installation. At normal
stop the stop sequence is active until the engine has come to standstill. Thereafter the system
automatically returns to “ready for start” mode in case no start block functions are active, i.e.
there is no need for manually resetting a normal stop.
Emergency stop can be activated with the local emergency stop button, or from a remote
location as applicable.
The engine safety module handles safety shutdowns. Safety shutdowns can be initiated either
independently by the safety module, or executed by the safety module upon a shutdown
request from some other part of the automation system.
Typical shutdown functions are:
● Lubricating oil pressure low
● Overspeed
● Oil mist in crankcase
● Lubricating oil pressure low in reduction gear
At a stop or shutdown the fuel injection is disabled and the pressure in the high pressure fuel
line is instantly released.
Depending on the application it is possible to override a shutdown via a separate input. It is
not possible to override a shutdown due to overspeed or emergency stop.
Before restart the reason for the shutdown must be thoroughly investigated and rectified.
14.2.3 Speed control

14.2.3.1 Main engines (mechanical propulsion)
The electronic speed control is integrated in the engine automation system.
The remote speed setting from the propulsion control is an analogue 4-20 mA signal. It is also
possible to select an operating mode in which the speed reference can be adjusted with
increase/decrease signals.
The electronic speed control handles load sharing between parallel engines, fuel limiters, and
various other control functions (e.g. ready to open/close clutch, speed filtering). Overload
protection and control of the load increase rate must however be included in the propulsion
control as described in the chapter Operating Ranges.
14.2.3.2 Generating sets

The electronic speed control is integrated in the engine automation system.
The load sharing can be based on traditional speed droop, or handled independently by the
speed control units without speed droop. The later load sharing principle is commonly referred
to as isochronous load sharing. With isochronous load sharing there is no need for load
balancing, frequency adjustment, or generator loading/unloading control in the external control
system.
In a speed droop system each individual speed control unit decreases its internal speed
reference when it senses increased load on the generator. Decreased network frequency with
higher system load causes all generators to take on a proportional share of the increased total
load. Engines with the same speed droop and speed reference will share load equally. Loading
and unloading of a generator is accomplished by adjusting the speed reference of the individual
speed control unit. The speed droop is normally 4%, which means that the difference in
frequency between zero load and maximum load is 4%.

In isochronous mode the speed reference remains constant regardless of load level. Both
isochronous load sharing and traditional speed droop are standard features in the speed
control and either mode can be easily selected. If the ship has several switchboard sections
with tie breakers between the different sections, then the status of each tie breaker is required
for control of the load sharing in isochronous mode.
14.3 Alarm and monitoring signals

Regarding sensors on the engine, please see the internal P&I diagrams in this product guide.
The actual configuration of signals and the alarm levels are found in the project specific
documentation supplied for all contracted projects.
14.4 Electrical consumers

14.4.1 Motor starters and operation of electrically driven pumps
Motor starters are not part of the control system supplied with the engine, but available as
loose supplied items.
14.4.1.1 Engine turning device (9N15)

The crankshaft can be slowly rotated with the turning device for maintenance purposes and
for engine slowturning. The engine turning device is controlled with an electric motor via a
frequency converter. The frequency converter is to be mounted on the external system. The
electric motor ratings are listed in the table below.
Table 14-2 Electric motor ratings for engine turning device
Engine type Voltage [V] Frequency [Hz] Power [kW] Current [A]
Wärtsilä 31 3 x 400 - 690V 50 / 60 4.0 10 - 6A
14.4.1.2 Pre-lubricating oil pump

The pre-lubricating oil pump must always be running when the engine is stopped. The engine
control system handles start/stop of the pump automatically via a motor starter.
It is recommended to arrange a back-up power supply from an emergency power source.
Diesel generators serving as the main source of electrical power must be able to resume their
operation in a black out situation by means of stored energy. Depending on system design
and classification regulations, it may be permissible to use the emergency generator.
Electric motor ratings are listed in the table below.
Table 14-3 Electric motor ratings for pre-lubricating pump
Engine type Voltage [V] Frequency [Hz] Power [kW] Current [A]
3 x 400 50 15.0 28.4

W31
3 x 440 60 15.0 25.7
14.4.1.3 Stand-by pump, lubricating oil (if applicable) (2P04)

The engine control system starts the pump automatically via a motor starter, if the lubricating
oil pressure drops below a preset level when the engine is running.

The pump must not be running when the engine is stopped, nor may it be used for
pre-lubricating purposes. Neither should it be operated in parallel with the main pump, when
the main pump is in order.
14.4.1.4 Stand-by pump, HT cooling water (if applicable) (4P03)

The engine control system starts the pump automatically via a motor starter, if the cooling
water pressure drops below a preset level when the engine is running.
14.4.1.5 Stand-by pump, LT cooling water (if applicable) (4P05)

The engine control system starts the pump automatically via a motor starter, if the cooling
water pressure drops below a preset level when the engine is running.
14.4.1.6 Circulating pump for preheater (4P04)

The preheater pump shall start when the engine stops (to ensure water circulation through
the hot engine) and stop when the engine starts. The engine control system handles start/stop
of the pump automatically.

14.5 System requirements and guidelines for diesel-electric

propulsion
Typical features to be incorporated in the propulsion control and power management systems
in a diesel-electric ship:
1. The load increase program must limit the load increase rate during ship acceleration and
load transfer between generators according to the curves in chapter 2.2 Loading Capacity.
● Continuously active limit: “normal max. loading in operating condition”.
● During the first 6 minutes after starting an engine: “preheated engine”
If the control system has only one load increase ramp, then the ramp for a preheated engine
is to be used.
The load increase rate of a recently connected generator is the sum of the load transfer
performed by the power management system and the load increase performed by the
propulsion control, if the load sharing is based on speed droop. In a system with isochronous
load sharing the loading rate of a recently connected generator is not affected by changes in
the total system load (as long as the generators already sharing load equally are not loaded
over 100%).
2. Rapid loading according to the “emergency” curve in chapter 2.2 Loading Capacity may
only be possible by activating an emergency function, which generates visual and audible
alarms in the control room and on the bridge.
3. The propulsion control should be able to control the propulsion power according to the
load increase rate at the diesel generators. Controlled load increase with different number of
generators connected and in different operating conditions is difficult to achieve with only
time ramps for the propeller speed.
4. The load reduction rate should also be limited in normal operation. Crash stop can be
recognised by for example a large lever movement from ahead to astern.
5. Some propulsion systems can generate power back into the network. The diesel generator
can absorb max. 5% reverse power.
6. The power management system performs loading and unloading of generators in a speed
droop system, and it usually also corrects the system frequency to compensate for the droop
offset, by adjusting the speed setting of the individual speed control units. The speed reference
is adjusted by sending an increase/decrease pulse of a certain length to the speed control
unit. The power management should determine the length of the increase/decrease pulse
based on the size of the desired correction and then wait for 30 seconds or more before
performing a new correction, in particular when performing small corrections.
The relation between duration of increase/decrease signal and change in speed reference is
usually 0.1 Hz per second. The actual speed and/or load will change at a slower rate.
7. The full output of the generator is in principle available as soon as the generator is connected
to the network, but only if there is no power limitation controlling the power demand. In practice
the control system should monitor the generator load and reduce the system load, if the
generator load exceeds 100%.
In speed droop mode all generators take an equal share of increased system load, regardless
of any difference in initial load. If the generators already sharing load equally are loaded beyond
their max. capacity, the recently connected generator will continue to pick up load according
to the speed droop curve. Also in isochronous load sharing mode a generator still on the
loading ramp will start to pick up load, if the generators in even load sharing have reached
their max. capacity.
8. The system should monitor the network frequency and reduce the load, if the network
frequency tends to drop excessively. To safely handle tripping of a breaker more direct action
can be required, depending on the operating condition and the load step on the engine(s).

Wärtsilä 31 Product Guide 15. Foundation
15. Foundation
Engines can be either rigidly mounted on chocks, or resiliently mounted on rubber elements.
If resilient mounting is considered, Wärtsilä must be informed about existing excitations such
as propeller blade passing frequency. Dynamic forces caused by the engine are listed in the
chapter Vibration and noise.
15.1 Steel structure design

The system oil tank may not extend under the reduction gear, if the engine is of dry sump type
and the oil tank is located beneath the engine foundation. Neither should the tank extend
under the support bearing, in case there is a PTO arrangement in the free end. The oil tank
must also be symmetrically located in transverse direction under the engine.
The foundation and the double bottom should be as stiff as possible in all directions to absorb
the dynamic forces caused by the engine, reduction gear and thrust bearing. The foundation
should be dimensioned and designed so that harmful deformations are avoided.
The foundation of the driven equipment must be integrated with the engine foundation.
15.2 Mounting of main engines

15.2.1 Rigid mounting
Main engines can be rigidly mounted to the foundation either on steel chocks or resin chocks.
The holding down bolts are through-bolts with a lock nut at the lower end and a hydraulically
tightened nut at the upper end. The tool included in the standard set of engine tools is used
for hydraulic tightening of the holding down bolts. Two of the holding down bolts are fitted
bolts and the rest are clearance bolts. The two Ø43H7/n6 fitted bolts are located closest to
the flywheel, one on each side of the engine.
A distance sleeve should be used together with the fitted bolts. The distance sleeve must be
mounted between the seating top plate and the lower nut in order to provide a sufficient
guiding length for the fitted bolt in the seating top plate. The guiding length in the seating top
plate should be at least equal to the bolt diameter.
The design of the holding down bolts is shown in the foundation drawings. It is recommended
that the bolts are made from a high-strength steel, e.g. 42CrMo4 or similar. A high strength
material makes it possible to use a higher bolt tension, which results in a larger bolt elongation
(strain). A large bolt elongation improves the safety against loosening of the nuts.
To avoid sticking during installation and gradual reduction of tightening tension due to
unevenness in threads, the threads should be machined to a finer tolerance than normal
threads. The bolt thread must fulfil tolerance 6g and the nut thread must fulfil tolerance 6H.
In order to avoid bending stress in the bolts and to ensure proper fastening, the contact face
of the nut underneath the seating top plate should be counterbored.
Lateral supports must be installed for all engines. One pair of supports should be located at
flywheel end and one pair (at least) near the middle of the engine. The lateral supports are to
be welded to the seating top plate before fitting the chocks. The wedges in the supports are
to be installed without clearance, when the engine has reached normal operating temperature.
The wedges are then to be secured in position with welds. An acceptable contact surface
must be obtained on the wedges of the supports.

15. Foundation Wärtsilä 31 Product Guide
15.2.1.1 Resin chocks

The recommended dimensions of resin chocks are 150 x 400 mm. The total surface pressure
on the resin must not exceed the maximum permissible value, which is determined by the
type of resin and the requirements of the classification society. It is recommended to select
a resin type that is approved by the relevant classification society for a total surface pressure
of 5 N/mm2. (A typical conservative value is Ptot 3.5 N/mm2).
During normal conditions, the support face of the engine feet has a maximum temperature of
about 75°C, which should be considered when selecting the type of resin.
The bolts must be made as tensile bolts with a reduced shank diameter to ensure a sufficient
elongation since the bolt force is limited by the permissible surface pressure on the resin. For
a given bolt diameter the permissible bolt tension is limited either by the strength of the bolt
material (max. stress 80% of the yield strength), or by the maximum permissible surface
pressure on the resin.
15.2.1.2 Steel chocks

The top plates of the foundation girders are to be inclined outwards with regard to the centre
line of the engine. The inclination of the supporting surface should be 1/100 and it should be
machined so that a contact surface of at least 75% is obtained against the chocks.
Recommended chock dimensions are 250 x 200 mm and the chocks must have an inclination
of 1:100, inwards with regard to the engine centre line. The cut-out in the chocks for the
clearance bolts shall be 44 mm (M42 bolts), while the hole in the chocks for the fitted bolts
shall be drilled and reamed to the correct size (Ø43H7) when the engine is finally aligned to
the reduction gear.
The design of the holding down bolts is shown the foundation drawings. The bolts are designed
as tensile bolts with a reduced shank diameter to achieve a large elongation, which improves
the safety against loosening of the nuts.
15.2.1.3 Steel chocks with adjustable height

As an alternative to resin chocks or conventional steel chocks it is also permitted to install the
engine on adjustable steel chocks. The chock height is adjustable between 45 mm and 65
mm for the approved type of chock. There must be a chock of adequate size at the position
of each holding down bolt.

Fig 15-1 Main engine seating and fastening, steel chocks (DAAF343802)


Fig 15-2 Main engine seating and fastening, resin chocks (DAAF346146)


Fig 15-3 Main engine seating and fastening, Adjustable chocks (DAAF346157)

15.2.2 Resilient mounting

In order to reduce vibrations and structure borne noise, main engines can be resiliently mounted
on rubber elements. The transmission of forces emitted by the engine is 10-20% when using
resilient mounting. For resiliently mounted engines a speed range of 500-750 rpm is generally
available.
Fig 15-4 Principle of resilient mounting (DAAF356004B)
15.3 Mounting of generating sets

15.3.1 Resilient mounting

Generating sets, comprising engine and generator mounted on a common base frame, are
usually installed on resilient mounts on the foundation in the ship.
The resilient mounts reduce the structure borne noise transmitted to the ship and also serve
to protect the generating set bearings from possible fretting caused by hull vibration.
The number of mounts and their location is calculated to avoid resonance with excitations
from the generating set engine, the main engine and the propeller.
NOTE
To avoid induced oscillation of the generating set, the following data must be sent
by the shipyard to Wärtsilä at the design stage:
● main engine speed [RPM] and number of cylinders

● propeller shaft speed [RPM] and number of propeller blades
The selected number of mounts and their final position is shown in the generating set drawing.
Fig 15-5 Recommended design of the generating set seating (DAAE020067B)
15.3.1.1 Rubber mounts

The generating set is mounted on conical resilient mounts, which are designed to withstand
both compression and shear loads. In addition the mounts are equipped with an internal buffer
to limit the movements of the generating set due to ship motions. Hence, no additional side
or end buffers are required.
The rubber in the mounts is natural rubber and it must therefore be protected from oil, oily
water and fuel.
The mounts should be evenly loaded, when the generating set is resting on the mounts. The
maximum permissible variation in compression between mounts is 2.0 mm. If necessary,
chocks or shims should be used to compensate for local tolerances. Only one shim is permitted
under each mount.

The transmission of forces emitted by the engine is 10 -20% when using conical mounts. For
the foundation design, see drawing 3V46L0294.
Fig 15-6 Rubber mount, (DAAE018766b)
15.4 Flexible pipe connections

When the engine or generating set is resiliently installed, all connections must be flexible and
no grating nor ladders may be fixed to the engine or generating set. When installing the flexible
pipe connections, unnecessary bending or stretching should be avoided. The external pipe
must be precisely aligned to the fitting or flange on the engine. It is very important that the
pipe clamps for the pipe outside the flexible connection must be very rigid and welded to the
steel structure of the foundation to prevent vibrations, which could damage the flexible
connection.

Wärtsilä 31 Product Guide 16. Vibration and Noise
16. Vibration and Noise

Wärtsilä 31 generating sets comply with vibration levels according to ISO 8528-9. Main engines
comply with vibration levels according to ISO 10816-6 Class 5.
16.1 External forces and couples

Some cylinder configurations produce external forces and couples. These are listed in the
tables below.
The ship designer should avoid natural frequencies of decks, bulkheads and superstructures
close to the excitation frequencies. The double bottom should be stiff enough to avoid
resonances especially with the rolling frequencies.
Fig 16-1 Coordinate system
Table 16-1 External forces
Engine Speed Freq. FY FZ Freq. FY FZ Freq. FY FZ

[RPM] [Hz] [kN] [kN] [Hz] [kN] [kN] [Hz] [kN] [kN]
8V31 720 24 --- --- 48 2 1 --- --- ---
750 25 --- --- 50 2 1 --- --- ---
10V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
12V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
14V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
16V31 720 48 4 2 --- --- --- --- --- ---
750 50 5 2 --- --- --- --- --- ---

16. Vibration and Noise Wärtsilä 31 Product Guide
Table 16-2 External couples
Engine Speed Freq. MY MZ Freq. MY MZ Freq. MY MZ

[RPM] [Hz] [kNm] [kNm] [Hz] [kNm] [kNm] [Hz] [kNm] [kNm]
8V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
10V31 720 12 38 38 24 --- --- 48 --- 0,2
750 12,5 41 41 25 --- --- 50 --- 0,2
12V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
14V31 720 12 22 22 24 35 20 48 1 3
750 12,5 24 24 25 38 21 50 1 4
16V31 720 --- --- --- --- --- --- --- --- ---
750 --- --- --- --- --- --- --- --- ---
16.2 Torque variations

Table 16-3 Torque variations
Engine Speed Freq. Mx Freq. Mx Freq. Mx Freq. Mx

[RPM] [Hz] [kNm] [Hz] [kNm] [Hz] [kNm] [Hz] [kNm]
8V31 720 24 25 48 14 72 31 -- --
750 25 19 50 14 75 31 -- --
10V31 720 24 25 30 82 60 41 90 21
750 25 27 31 82 63 41 94 21
12V31 720 36 24,46 72 47 108 8 144 1
750 37,5 23 75 47 112,5 8 150 1
14V31 720 42 8 84 38 126 1 168 1
750 44 8 88 38 131 1 175 1
16V31 720 48 28 96 24 144 1 192 1
750 50 28 100 24 150 1 200 1
16.3 Mass moments of inertia

The mass-moments of inertia of the main engines (including flywheel) are typically as follows:
Engine J (kg m2) Engine J (kg m2)
8V31 640 – 740 14V31 890 – 990

10V31 720 – 820 16V31 980 – 1080
12V31 800 – 900
16.4 Air borne noise

The airborne noise of an engine is measured as sound power level based on ISO 9614-2. The
results represent typical engine A-weighted sound power levels at engine full load and nominal
speed.

Wärtsilä 31 Product Guide 16. Vibration and Noise
Engine A-weighted Sound Power Level in Octave Frequency Band [dB, ref. 1pW]
[Hz] 125 250 500 1000 2000 4000 8000 Total
8V 100 110 115 121 119 116 114 125
10V 99 107 115 118 121 118 114 125
12V 100 109 116 121 120 117 114 125
14V 100 110 117 120 121 118 115 126
16V 100 111 118 121 121 118 115 127
16.5 Exhaust noise

The results represent typical exhaust gas free field linear sound power levels at engine full
load and nominal speed.
Exhaust Gas Sound Power Level in Octave Frequency Band [dB, ref. 1pW]
[Hz] 32 63 125 250 500 1000 2000 4000 Total
8V 144 147 129 128 126 123 120 118 149
10V 149 140 134 133 131 127 125 121 150
12V 135 132 124 121 116 104 100 98 139
14V 137 134 126 123 115 105 99 97 141
16V 140 141 126 123 114 105 99 97 144

Wärtsilä 31 Product Guide 17. Power Transmission
17. Power Transmission
17.1 Flexible coupling

The power transmission of propulsion engines is accomplished through a flexible coupling or
a combined flexible coupling and clutch mounted on the flywheel. The crankshaft is equipped
with an additional shield bearing at the flywheel end. Therefore also a rather heavy coupling
can be mounted on the flywheel without intermediate bearings.
The type of flexible coupling to be used has to be decided separately in each case on the
basis of the torsional vibration calculations.
In case of two bearing type generator installations a flexible coupling between the engine and
the generator is required.
17.2 Clutch
In many installations the propeller shaft can be separated from the diesel engine using a clutch.
The use of multiple plate hydraulically actuated clutches built into the reduction gear is
recommended.
A clutch is required when two or more engines are connected to the same driven machinery
such as a reduction gear.
To permit maintenance of a stopped engine clutches must be installed in twin screw vessels
which can operate on one shaft line only.
17.3 Shaft locking device

A shaft locking device should also be fitted to be able to secure the propeller shaft in position
so that wind milling is avoided. This is necessary because even an open hydraulic clutch can
transmit some torque. Wind milling at a low propeller speed (<10 rpm) can due to poor
lubrication cause excessive wear of the bearings.
The shaft locking device can be either a bracket and key or an easier to use brake disc with
calipers. In both cases a stiff and strong support to the ship’s construction must be provided.
To permit maintenance of a stopped engine clutches must be installed in twin screw vessels
which can operate on one shaft line only. A shaft locking device should also be fitted to be
able to secure the propeller shaft in position so that wind milling is avoided. This is necessary
because even an open hydraulic clutch can transmit some torque. Wind milling at a low
propeller speed (<10 rpm) can due to poor lubrication cause excessive wear of the bearings.
The shaft locking device can be either a bracket and key or an easier to use brake disc with
calipers. In both cases a stiff and strong support to the ship’s construction must be provided.

17. Power Transmission Wärtsilä 31 Product Guide
Fig 17-1 Shaft locking device and brake disc with calipers
17.4 Input data for torsional vibration calculations

A torsional vibration calculation is made for each installation. For this purpose exact data of
all components included in the shaft system are required. See list below.
Installation
● Classification
● Ice class
● Operating modes
Reduction gear
A mass elastic diagram showing:
● All clutching possibilities
● Sense of rotation of all shafts
● Dimensions of all shafts
● Mass moment of inertia of all rotating parts including shafts and flanges
● Torsional stiffness of shafts between rotating masses
● Material of shafts including tensile strength and modulus of rigidity
● Gear ratios
● Drawing number of the diagram
Propeller and shafting
A mass-elastic diagram or propeller shaft drawing showing:
● Mass moment of inertia of all rotating parts including the rotating part of the OD-box, SKF
couplings and rotating parts of the bearings
● Mass moment of inertia of the propeller at full/zero pitch in water
● Torsional stiffness or dimensions of the shaft
● Material of the shaft including tensile strength and modulus of rigidity
● Drawing number of the diagram or drawing
Main generator or shaft generator
A mass-elastic diagram or an generator shaft drawing showing:

Wärtsilä 31 Product Guide 17. Power Transmission
● Generator output, speed and sense of rotation

● Mass moment of inertia of all rotating parts or a total inertia value of the rotor, including
the shaft
● Torsional stiffness or dimensions of the shaft
● Material of the shaft including tensile strength and modulus of rigidity
● Drawing number of the diagram or drawing
Flexible coupling/clutch
If a certain make of flexible coupling has to be used, the following data of it must be informed:
● Mass moment of inertia of all parts of the coupling
● Number of flexible elements
● Linear, progressive or degressive torsional stiffness per element
● Dynamic magnification or relative damping
● Nominal torque, permissible vibratory torque and permissible power loss
● Drawing of the coupling showing make, type and drawing number
Operational data
● Operational profile (load distribution over time)
● Clutch-in speed
● Power distribution between the different users
● Power speed curve of the load
17.5 Turning gear

The engine is equipped with an electrical driven turning gear, capable of turning the flywheel
and crankshaft.

Wärtsilä 31 Product Guide 18. Engine Room Layout
18. Engine Room Layout
18.1 Crankshaft distances

Minimum crankshaft distances are to be arranged in order to provide sufficient space between
engines for maintenance and operation.
18.1.1 Main engines
Fig 18-1 W8V31 & W10V31, turbocharger in free end (DAAF324239A)

18. Engine Room Layout Wärtsilä 31 Product Guide
Fig 18-2 W8V31 & W10V31, turbocharger in driving end (DAAF353762A)
Fig 18-3 W12V31, W14V31 & W16V31, turbocharger in free end (DAAF392987)

Fig 18-4 W12V31, W14V31 & W16V31, turbocharger in driving end (DAAF393139)

18.1.2 Generating sets
Fig 18-5 V-engines, turbocharger in free end (DAAF363645)
Engine A B C D
W 8V31 2200 2620 3800 2300

18.2 Space requirements for maintenance

18.2.1 Working space around the engine
The required working space around the engine is mainly determined by the dismounting
dimensions of engine components, and space requirement of some special tools. It is especially
important that no obstructive structures are built next to engine driven pumps, as well as
camshaft and crankcase doors.
However, also at locations where no space is required for dismounting of engine parts, a
minimum of 1000 mm free space is recommended for maintenance operations everywhere
around the engine.
18.2.2 Engine room height and lifting equipment

The required engine room height is determined by the transportation routes for engine parts.
If there is sufficient space in transverse and longitudinal direction, there is no need to transport
engine parts over the engine and in such case the necessary height is minimized. Separate
lifting arrangements are usually required for overhaul of the turbocharger since the crane travel
is limited by the exhaust pipe. A chain block on a rail located over the turbocharger axis is
recommended.
18.2.3 Maintenance platforms

In order to enable efficient maintenance work on the engine, it is advised to build the
maintenance platforms on recommended elevations. The width of the platforms should be at
minimum 800 mm to allow adequate working space. The surface of maintenance platforms
should be of non-slippery material (grating or chequer plate).
NOTE
Working Platforms should be designed and positioned to prevent personnel slipping,
tripping or falling on or between the walkways and the engine
18.3 Transportation and storage of spare parts and tools

Transportation arrangement from engine room to storage and workshop has to be prepared
for heavy engine components. This can be done with several chain blocks on rails or
alternatively utilising pallet truck or trolley. If transportation must be carried out using several
lifting equipment, coverage areas of adjacent cranes should be as close as possible to each
other.
Engine room maintenance hatch has to be large enough to allow transportation of main
components to/from engine room.
It is recommended to store heavy engine components on slightly elevated adaptable surface
e.g. wooden pallets. All engine spare parts should be protected from corrosion and excessive
vibration.
On single main engine installations it is important to store heavy engine parts close to the
engine to make overhaul as quick as possible in an emergency situation.
18.4 Required deck area for service work

During engine overhaul some deck area is required for cleaning and storing dismantled
components. Size of the service area is dependent of the overhauling strategy chosen, e.g.
one cylinder at time, one bank at time or the whole engine at time. Service area should be
plain steel deck dimensioned to carry the weight of engine parts.

18.4.1 Service space requirement

18.4.1.1 Service space requirement, main engine
Fig 18-6 Service space requirement, Main engine W8V31 & W10V31 (DAAF063858C)

Fig 18-7 Service space requirement, Main engine W12V31, W14V31 & W14V31
(DAAF361169)
Fig 18-8 Service space requirement, Main engine W12V31, W14V31 & W14V31
Special cases (DAAF361169)

Wärtsilä 31 Product Guide 19. Transport Dimensions and Weights
19. Transport Dimensions and Weights
19.1 Lifting of main engines
Fig 19-1 Lifting of main engines (DAAF336773B)
Engine L1 L2 L3 L4 H1 H2 H3 H4 H5
W 8V31 1280 1321 1221 2200 7575 6729 1775 846 1496
W 10V31 1920 1321 1542 2200 8194 7348 1755 846 1496
W 12V31 1920 1961 2182 2200 8194 7348 1755 846 1496
W 14V31 1920 1961 2182 2200 8194 7348 1755 846 1496
W 16V31 1920 2601 2822 2200 8194 7348 1755 846 1496

19. Transport Dimensions and Weights Wärtsilä 31 Product Guide
19.2 Lifting of generating sets
Fig 19-2 Lifting of generating sets (DAAF341224)

19.3 Engine components

Table 19-1 Turbocharger and cooler inserts
Weight Dimensions [mm]

Engine
[kg] A B C
W 8V31 232 924 630 310
W 10V31 232 924 630 310
Fig 19-3 Lube oil cooler

Engine
[kg] D E F
W 8V31 785 1028 812 500
W 10V31 785 1028 812 500
Fig 19-4 Charge air cooler (HP)

Engine
[kg] G H I
W 8V31 830 1170 850 625
W 10V31 830 1170 850 625
Fig 19-5 Charge air cooler (LP)
Dimensions
Weight [mm]
Engine
[kg]
J2 K2
W 8V31 1568 1969 1198
W 10V31 1568 1969 1198
Fig 19-6 Turbocharger (LP)

19. Transport Dimensions and Weights Wärtsilä 31 Product Guide
Dimensions
Weight [mm]
Engine
[kg]
J K
W 8V31 680 1610 891
W 10V31 680 1610 891
Fig 19-7 Turbocharger (HP)

Fig 19-8 Major spare parts (DAAF337022)
Table 19-2 Weights
Item Description Weight [kg] Item Description Weight [kg]

no No
1 Connecting rod 192 9 Starting valve 7.6
2 Piston 72.4 10 Main bearing shell 4.7
3 Cylinder liner 307 11 Split gear wheel 94.7
4 Cylinder head 400 12 Small intermediate gear 21.6
5 Inlet valve 5.2 13 Large intermediate gear 60.6
6 Exhaust valve 3.3 14 Camshaft drive gear 61.8
7 HP fuel pump 134 Piston ring set 1.5

15
8 Injection valve 27 Piston ring 0.5

Wärtsilä 31 Product Guide 20. Product Guide Attachments
20. Product Guide Attachments

This and other product guides can be accessed on the internet, from the Business Online
Portal at www.wartsila.com. Product guides are available both in web and PDF format. Drawings
are available in PDF and DXF format, and in near future also as 3D models. Consult your sales
contact at Wärtsilä to get more information about the product guides on the Business Online
Portal.
The attachments are not available in the printed version of the product guide.

Wärtsilä 31 Product Guide 21. ANNEX
21. ANNEX
21.1 Unit conversion tables

The tables below will help you to convert units used in this product guide to other units. Where
the conversion factor is not accurate a suitable number of decimals have been used.
Length conversion factors Mass conversion factors

Convert from To Multiply by Convert from To Multiply by
mm in 0.0394 kg lb 2.205
mm ft 0.00328 kg oz 35.274
Pressure conversion factors Volume conversion factors

kPa psi (lbf/in2) 0.145 m3 in3 61023.744
kPa lbf/ft2 20.885 m3 ft3 35.315
kPa inch H2O 4.015 m3 Imperial gallon 219.969
kPa foot H2O 0.335 m3 US gallon 264.172
kPa mm H2O 101.972 m3 l (litre) 1000
kPa bar 0.01
Power conversion Moment of inertia and torque conversion factors

kW hp (metric) 1.360 kgm2 lbft2 23.730
kW US hp 1.341 kNm lbf ft 737.562
Fuel consumption conversion factors Flow conversion factors

g/kWh g/hph 0.736 m3/h (liquid) US gallon/min 4.403
g/kWh lb/hph 0.00162 m3/h (gas) ft3/min 0.586
Temperature conversion factors Density conversion factors

°C F F = 9/5 *C + 32 kg/m3 lb/US gallon 0.00834
°C K K = C + 273.15 kg/m3 lb/Imperial gallon 0.01002
kg/m3 lb/ft3 0.0624
21.1.1 Prefix
Table 21-1 The most common prefix multipliers
Name Symbol Factor Name Symbol Factor Name Symbol Factor

tera T 1012 kilo k 103 nano n 10-9
giga G 109 milli m 10-3
mega M 106 micro μ 10-6

21. ANNEX Wärtsilä 31 Product Guide
21.2 Collection of drawing symbols used in drawings
Fig 21-1 List of symbols (DAAE000806D)

Wärtsilä is a global leader in complete lifecycle power solutions
for the marine and energy markets. By emphasising technological
innovation and total efficiency, Wärtsilä maximises the
environmental and economic performance of the vessels and
power plants of its customers.
www.wartsila.com

Product Guide o e w31

Uploaded by

Copyright:

Available Formats

Product Guide o e w31

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Guide o e w31

Uploaded by

Copyright:

Available Formats

What is the document about?

What is the document about?

What information is provided in the introduction?

What information is provided in the introduction?

Wärtsilä 31

Issue Published Updates

2/2017 28.09.2017 see CN-A076175

Wärtsilä, Marine Solutions

Vaasa, September 2017

Wärtsilä 31 Product Guide - a3 - 28 September 2017 iii

iv Wärtsilä 31 Product Guide - a3 - 28 September 2017

2. Operating Ranges ................................................................................................................................ 2-1

3. Technical Data ...................................................................................................................................... 3-1

4. Description of the Engine .................................................................................................................... 4-1

5. Piping Design, Treatment and Installation ......................................................................................... 5-1

6. Fuel Oil System .................................................................................................................................... 6-1

7. Lubricating Oil System ........................................................................................................................ 7-1

8. Compressed Air System ...................................................................................................................... 8-1

9. Cooling Water System ......................................................................................................................... 9-1

Wärtsilä 31 Product Guide - a3 - 28 September 2017 v

9.2 External cooling water system .................................................................................................... 9-2

10. Combustion Air System ....................................................................................................................... 10-1

11. Exhaust Gas System ............................................................................................................................ 11-1

12. Turbocharger Cleaning ........................................................................................................................ 12-1

13. Exhaust Emissions ............................................................................................................................... 13-1

14. Automation System ............................................................................................................................. 14-1

15. Foundation ............................................................................................................................................ 15-1

16. Vibration and Noise .............................................................................................................................. 16-1

17. Power Transmission ............................................................................................................................ 17-1

18. Engine Room Layout ........................................................................................................................... 18-1

19. Transport Dimensions and Weights ................................................................................................... 19-1

20. Product Guide Attachments ............................................................................................................... 20-1

vi Wärtsilä 31 Product Guide - a3 - 28 September 2017

21. ANNEX ................................................................................................................................................... 21-1

Wärtsilä 31 Product Guide - a3 - 28 September 2017 vii

1. Main Data and Outputs

Cylinder bore ........................ 310 mm

Stroke ................................... 430 mm

Number of valves ................. 2 inlet valves

V-angle ................................. 50°

Direction of rotation ............. Clockwise, counterclockwise

Speed ................................... 720, 750 rpm

Mean piston speed ............... 10.32 - 10.75 m/s

1.1 Maximum continuous output

Cylinder Main engines Generating sets

[kW] Engine [kW] Generator [kVA] Engine [kW] Generator [kVA]

W 8V31 4880 4720 5664 4880 5856

W 10V31 6100 5900 7080 6100 7320

W 12V31 7320 7080 8496 7320 8784

W 14V31 8540 8260 9912 8540 10248

W 16V31 9760 9440 11328 9760 11712

The mean effective pressure Pe can be calculated as follows:

Pe = mean effective pressure [bar]

P = output per cylinder [kW]

n = engine speed [r/min]

D = cylinder diameter [mm]

L = length of piston stroke [mm]

c = operating cycle (4)

Wärtsilä 31 Product Guide - a3 - 28 September 2017 1-1

1.2 Reference conditions