All-on-4® treatment concept

Procedures manual
Original protocol for All-on-4® treatment concept
The All-on-4® treatment concept is a rehabilitation concept
that maximizes the use of available bone. The surgical and
prosthetic procedures follow a strict protocol including the
products to be used. The success of the All-on-4® treatment
concept is due to these specific protocols and products,
namely NobelSpeedy implants, which have been used with
10 years of follow-up. For the long term follow-up studies
supporting the result and the success rate of the All-on-4®
treatment concept, please visit nobelbiocare.com or ask
your Nobel Biocare representative for references.

The All-on-4® and the All-on-4® with NobelGuide treatment

concepts were developed together with Paulo Malo, DDS,
PhD, at MALO CLINIC.

Note: In order to improve readability, Nobel Biocare does

not use ™ or ® in the running text. By doing so, however,
Nobel Biocare does not waive any right to the trademark
or registered mark and nothing herein shall be construed
to the contrary.

Disclaimer: Some products may not be regulatory

cleared/released for sale in all markets. Please contact
the local Nobel Biocare sales office for current product
assortment and availability.
 3

Contents

Introduction A proven and successful concept 4

Conventional versus guided surgery 5
Conventional surgery Quick guide 6
Treatment planning 7
Clinical procedure for edentulous mandible 8
Clinical procedure for edentulous maxilla 11
Laboratory procedure 12
Guided surgery Optimized implant placement and prosthetic outcome with NobelGuide® 13
Quick guide 14
Treatment planning 15
Clinical procedure 18
Laboratory procedures 22
Product information Final restorations 26
Multi-unit Abutments 27
Surgical components 31
Laboratory components 33
Appendices Clinical cases 35
Customer service worldwide 39
4 All-on-4® treatment concept manual // Introduction

A proven and successful concept

Only four implants needed All-on-4® treatment concept

step by step
The All-on-4® treatment concept, with its use Fixed temporary prosthetic solutions
of straight and angled Multi-unit Abutments, With the All-on-4® treatment concept,
was developed to provide edentulous and patients benefit from an immediate implant-
soon-to-be edentulous patients with an supported all-acrylic restoration, as a
immediately loaded full-arch restoration on provisional prosthesis is screwed onto
only four implants – two placed vertically in the implants right after surgery.
the anterior, two placed at an angle of up to
45° in the posterior region. Final restorative solutions Insertion of implants
Final solutions include both fixed and fixed-
By tilting the two posterior implants, the removable prostheses:
bone-to-implant contact is enhanced, pro- – Fixed solutions include NobelProcera
viding optimized bone support even with Implant Bridge with acrylic veneering, or
minimum bone volume. Additionally, tilting individual NobelProcera crowns cemented
of implants in the maxilla allows for im- to the bridge framework.
proved anchorage in better quality anterior – Fixed-removable solutions include acrylic
bone and bicortical anchorage in the cortical prosthesis on a NobelProcera Implant
bone of the sinus wall and the nasal fossa. Bar Overdenture, attached by means of
a variety of attachment systems. Securing of Multi-unit Abutments

Tilting of the posterior implants also helps

avoid vital structures, such as the mandibu- NobelProcera Implant Bridge and Implant
lar nerve or the maxillary sinus, and results Bar Overdenture are milled from a biocom-
in a better distribution of implants along the patible titanium monobloc using state-of-
alveolar crest, which optimizes load distribu- the-art CAD/CAM technology, resulting in
tion and allows for a final prosthesis with up consistent precision of fit, individualized
to 12 teeth. design and optimized esthetics.

Multi-unit Abutments Guided surgery

Nobel Biocare offers straight, as well as 17° The All-on-4® treatment concept can be
and 30° angled Multi-unit Abutments for all planned and performed using NobelGuide, Securing of provisional prosthesis with
prosthetic screws
Nobel Biocare implants and a selection of ensuring accurate diagnostics, planning and
other major implant systems. The abutments implant placement.
are available with various collar heights to
match the thickness of the soft tissue.
 All-on-4® treatment concept manual // Introduction 5

Conventional versus guided surgery

The All-on-4® treatment concept can be performed in two ways:

Conventional surgery – raising a flap NobelGuide – flap to flapless approach

Conventional flap procedure with traditional planning and 3D diagnostics and treatment planning and a custom-
a standardized All-on-4® Guide for predictable and optimized designed surgical template to correctly drill and position
positioning of the implants. the implants.

Available implant systems

– NobelSpeedy Groovy
– Brånemark System Mk III and Mk IV*
– NobelActive**
– NobelParallel Conical Connection**
–N obelReplace Conical Connection**, NobelReplace/Replace
Select Tapered and NobelReplace Platform Shift
– NobelReplace/Replace Select Straight and NobelSpeedy
Replace

* Guided surgery is only available for Brånemark System Mk III Groovy and Shorty and Brånemark System Mk III TiUnite RP.
** Non-engaging 30° Multi-unit Abutments are not available for implants with internal conical connection.
6 All-on-4® treatment concept manual // Conventional surgery

Quick guide conventional surgery

Mandible Maxilla

1 1

2 2

3 3
 All-on-4® treatment concept manual // Conventional surgery 7

Treatment planning

The All-on-4® treatment concept was developed to maximize the use of available bone and to allow for Immediate Function.
When planning a conventional treatment using a flap technique, consider the following.

General considerations – To reduce the cantilevers, tilt the posterior implants to
– Ability to achieve primary implant stability: a maximum of 45°.
- Implants should withstand a minimum tightening torque – If the angulation is 30° or more, it is necessary to splint
of 35 Ncm. the tilted implants.
- If this tightening torque is not achieved, a conventional – For tilted posterior implants, plan the distal screw access
healing phase is recommended prior to delivery of the holes to be located at the occlusal plane of the first molar,
provisional or final restoration. second pre-molar, or first pre-molar.
– No severe parafunctions. – The All-on-4® treatment concept does not require a wider
– Indicated for edentulous maxilla with a minimum bone opening of the mouth than a treatment with straight im-
width of 5 mm and a minimum bone height of 10 mm plants due to the angulation of the posterior implants.
from canine to canine. – If there are extraction sites, clean them thoroughly. It is
– Indicated for edentulous mandible with a minimum advisable to place implants between extraction sockets.
bone width of 5 mm and a minimum bone height of 8 mm
inbetween the mental foramina.

Specific considerations – implants

– If possible, the posterior implants should be ∅ 4.0 mm or
∅ 4.3 mm.
– When placing posterior implants with:
- internal tri-channel connection: make sure that one of the
tri-channel lobes is pointing distally or slightly buccally.
- internal conical connection: make sure that one of the
flat sides of the hexagon is parallel to the buccal side.
Tip: The implant drivers have markings to facilitate proper
orientation of the implants.

Notes:
– For internal tri-channel and external hex connection, the 30°
Multi-unit Abutment is only available for RP implants. The 17°
Multi-unit Abutment is available for NP and RP implants.
– For internal conical connection, the 17° Multi-unit Abutments
are available for NP, RP and WP implants, and the 30° Multi-
unit Abutments for NP and RP implants.

Specific considerations – prosthetics it may be used to fabricate the immediate all-acrylic bridge.
– No extensions over one tooth on each side for an immediate – For proper esthetics and function, the final bridge should
all-acrylic bridge, which should have a maximum of 12 teeth. have 12 teeth and a supporting metal framework.
– If the patient’s removable prosthesis is in good condition,

Note: For a full description of implant placement, prosthetic procedures, and all instruments needed, please refer to the
respective procedures manuals (for the current version see nobelbiocare.com/resources).
8 All-on-4® treatment concept manual // Conventional surgery

Clinical procedure for edentulous mandible

The images show Immediate Function with an all-acrylic bridge and NobelSpeedy Groovy RP implants.

1 Position All-on-4® Guide

–A fter making an incision for flap elevation, make an
osteotomy of approximately 8 mm in the midline using
a ∅ 2 mm Twist Drill.
– Place the All-on-4® Guide in the osteotomy.

2 Prepare posterior site

– Drill to appropriate depth using a ∅ 2 mm Twist Drill tilted
to a maximum angle of 45°.
– Check for correct angulation with the All-on-4® Guide.
–P  repare the site according to the density of the bone.
Insert the implant.
–F  or Immediate Function, the implants should withstand a
final tightening torque between 35 and 45 Ncm.
– If indicated, use a Bone Mill together with a Bone Mill
Guide to remove bone that could hinder correct seating of
the abutment.
– Place a 30° Multi-unit Abutment. Tighten to 15 Ncm using
Unigrip Screwdriver Machine and Manual Torque Wrench
Prosthetic.
– Perform the same procedure for the opposite posterior site.

Caution: It is important to identify the mental foramen and

exiting inferior dental nerve. The final position of the implant
should be in front of the foramen, avoiding the nerve loop.
 All-on-4® treatment concept manual // Conventional surgery 9

3 Prepare anterior site

– Prepare two anterior sites, as far apart from each other as
possible, allowing for a safe distance from the apex of the
posterior implants.
– If indicated use a Bone Mill together with a Bone Mill
Guide to remove bone that could hinder correct seating
of the abutment.
– Place straight or 17° Multi-unit Abutments and allow for
proper emergence of the prosthetic screw.
– Tighten 17° Multi-unit Abutments to 15 Ncm using
Unigrip Screwdriver Machine and Manual Torque
Wrench Prosthetic.
– Tighten straight Multi-unit Abutments to 35 Ncm using
Screwdriver Machine Multi-unit and Manual Torque
Wrench Prosthetic.

Option: delayed loading

If the required tightening torque for Immediate Function
(minimum 35 Ncm) cannot be achieved or the treatment of
choice is a delayed loading protocol, a conventional healing
phase is recommended prior to delivery of a provisional or
final restoration.

– Place cover screws on all four implants and suture back

the flap.
– Wait with further steps until osseointegration has taken
place.
10 All-on-4® treatment concept manual // Conventional surgery

4 Take an impression
– After suturing, connect the Multi-unit Impression Copings
Open Tray to the Multi-unit Abutments.
– Take an impression using silicone soft putty material and
a customized open tray.

Tip: To avoid impression material entering into the tissue,

always use a putty soft addition silicone. The less fluid the
material is, the less it can penetrate into the tissue.

5 Laboratory procedure for provisional bridge

A model and a provisional restoration are made at the dental
laboratory. For more information, see the step-by-step labo-
ratory procedure on page 12.

6 Connect provisional bridge

– Place the all-acrylic bridge on the abutments.
– Tighten the prosthetic screws to 15 Ncm using
Unigrip Screwdriver Machine and Manual Torque
Wrench Prosthetic.
– Block out screw access and fill holes with
suitable material.
– Check the occlusion.

7 Final restoration
After a sufficient healing period, follow established
prosthetic procedures for the final restoration, preferably
a NobelProcera Implant Bridge.
 All-on-4® treatment concept manual // Conventional surgery 11

Clinical procedure for edentulous maxilla

Note: When performing the All-on-4® treatment concept in the maxilla, add the following steps for the posterior sites in ad-
dition to those for the posterior sites in the mandible.

Prepare posterior site

– Identify the anterior wall of the maxillary sinus by drilling
a small opening on the lateral wall of the maxilla where the
anterior wall is expected to be.
– Explore the wall with a probe and extend the window
if necessary.
– Mark the position of the anterior wall with the surgical
marker.
– Start the site preparation as posterior as possible, allowing
approximately 4 mm from the sinus wall.

– Incline the drill (not more than 45°) as far back as possible
to minimize the cantilever.
12 All-on-4® treatment concept manual // Conventional surgery

Laboratory procedure

Fabricate the all-acrylic bridge

– Fabricate a soft-tissue model using Abutment Replicas
Multi-unit.
– Use guide pins (available in 10 and 20 mm lengths) or lab
screws to place Temporary Copings Multi-unit on the repli-
cas. It is preferable to use temporary copings in titanium.
– Adjust the copings if needed.

– Fabricate an all-acrylic bridge using a high-density acrylic.

–R einforce the weak points of the prosthesis around the
cylinders with more acrylic.

Notes:
– If possible, a tooth set-up should be tried in the patient’s
mouth before finalizing the bridge.
–T  he bridge can also be made by converting the existing
denture into a bridge.
 All-on-4® treatment concept manual // Guided surgery 13

Optimized implant placement and

prosthetic outcome with NobelGuide®

NobelGuide is ideal for the All-on-4® treatment Safe and predictable implant
concept, as it optimizes implant placement by placement
means of 3D diagnostics, digital treatment After planning the case in NobelClinician
planning and guided surgery with a custom- Software, a ready-to-use custom-designed
designed surgical template. It supports mini- surgical template, together with all neces-
mally invasive flapless techniques as well as sary implants, abutments and surgical in-
surgical access through mini-flaps and full struments, can be ordered online in a single Existing prosthesis can be modified
flaps. order. The surgical template enables guided directly into a radiographic guide
implant site preparation and precise and ef-
Accurate diagnostics and prosthetic- ficient implant insertion, which minimizes
driven planning patient pain and swelling.
Based on 3D (CB)CT diagnostic imaging of
the patient and a radiographic guide, virtual Prefabrication of provisional
implant placement following prosthetic- prosthesis before surgery
driven planning can be performed within The surgical template can be used to create
the NobelClinician Software, ensuring high a stone model with implant replicas already
diagnostic accuracy and safe and predict- in place before surgery. This enables the Digital prosthetic-driven planning in
able implant placement. dental technician to produce the provisional NobelClinician Software

prosthesis and the Multi-unit Abutment

With the combination of the 3D radiological placement jig in advance, so that the clini-
dataset and 3D models of bone and radio- cian can finalize the prosthesis and mount it
graphic guide, dental professionals can eval- on the implants right after surgery.
uate bone quantity and quality, mark vital
anatomical structures such as the alveolar
nerve and the maxillary sinus, and position
the implants according to prosthetic needs.
Through controlled and customizable angu-
lation of the dental reslice planes in the split- Guided implant insertion with
screen view of the software, the tilted poste- ready-to-use surgical template

rior implants are also ideally positioned.

14 All-on-4® treatment concept manual // Guided surgery

Quick guide guided surgery

1 2

3 4

5 6
 All-on-4® treatment concept manual // Guided surgery 15

Treatment planning

The All-on-4® treatment concept was developed to maximize the use of available bone and to allow for Immediate Function.
When planning the All-on-4® treatment concept with NobelGuide, consider the following.

General considerations – If the angulation is 30° or more, it is necessary to splint the
– For NobelGuide computer-based planning, a CT scan tilted implants.
using a radiographic guide is required. Please refer to – For tilted posterior implants, plan the distal screw-access
the NobelGuide concept manual for details. holes to be located at the occlusal plane of the first molar,
– Ability to achieve primary implant stability: second premolar, or first premolar.
- Implants should withstand the minimum tightening – The All-on-4® treatment concept does not require a wider
torque of 35 Ncm to allow for Immediate Function (perform opening of the mouth than a treatment with straight
final torque measurement without surgical template). implants due to the angulation of the posterior implants.
- If this tightening torque is not achieved, a conventional However, as with all NobelGuide treatments, it is important
healing phase is recommended prior to delivery of the to compensate for the extra height needed for NobelGuide
provisional or final restoration. components and instruments.
– No severe parafunctions.
– Indicated for totally edentulous maxilla with a minimum Smile line consideration
bone width of 5 mm and a minimum bone height of Pay special attention to the transition zone and smile line
10 mm from canine to canine. when planning the case. If the smile line does not hide the
– Indicated for totally edentulous mandible with a minimum transition zone, pre-prosthetic surgery reducing the alveolar
bone width of 5 mm and a minimum bone height of 8 mm bone needs to be taken into consideration.
inbetween the mental foramina.
– To reduce the cantilevers, tilt the posterior implants to a
maximum of 45°.

Specific considerations – implants

– If possible, the posterior implants should be ∅ 4.0 mm or
∅ 4.3 mm.

Note: The 30° Multi-unit Abutment Non-Engaging is

only available for RP implants with internal tri-channel and
external hex connection. It is not available for implants with
internal conical connection.

Specific considerations – prosthetics

– No extensions over one tooth on each side for an immediate
all-acrylic bridge, which should have a maximum of 12 teeth.
– If the patient’s removable prosthesis is in good condition,
it may be used to fabricate the immediate all-acrylic bridge.
– For proper esthetics and function, the final bridge should
have 12 teeth and a supporting metal framework.

Note: For a full description of implant placement, prosthetic procedures, and all instruments needed, please refer to the
respective procedures manuals (for the current version see nobelbiocare.com/resources).
16 All-on-4® treatment concept manual // Guided surgery

Checklist prior to surgery

  Correct implants, components and instruments

for guided surgery

  Printed planning report from NobelClinician Software

 Surgical template manufactured by Nobel Biocare

(check that it corresponds to the template designed in
NobelClinician Software. Also verify precision of fit on
master model and patient prior to surgery)

  Surgical index manufactured by dental laboratory

  Prosthetic components

  Temporary restoration

  Disinfection agent for surgical template

  The jig construction for placing 30° Multi-unit

Abutments Non-Engaging, which includes: 4
1. Impression Coping Open Tray Multi-unit
2. Guide Pin
3. 30° Multi-unit Abutment Non-Engaging including:*
4. Abutment Holder
5. Jig Stabilizer (modified Impression Coping 2
Open Tray Multi-unit)
6. Abutment Screw

For more information on how to make the jig, see

1 5
laboratory procedure on page 24.
For instructions on cleaning the jig, see page 17. 3
6

* When ordering 30° Multi-unit Abutment Non-Engaging, the Abutment Holder, Jig Stabilizer and Abutment Screw are included.
 All-on-4® treatment concept manual // Guided surgery 17

NobelGuide Surgical Template

The NobelGuide Surgical Template is made of a material that
is sensitive to moisture and UV light. Therefore:
– Store the surgical template together with a moisture absor-
bent in the protective plastic bag in which it was delivered.
– Store the surgical template in a dry and dark location.
– Do not expose the surgical template to direct sunlight.
– Do not remove the moisture absorbent.

Immediately before surgery

– Use a high level disinfectant (e.g. chlorhexadine) according
to manufacturer's instructions.
– Rinse thoroughly with sterile water. Dry quickly, but with-
out using heat.

Warning: The NobelGuide Surgical Template may deform if

exposed to liquids (even water) for more than 40 minutes.

Acrylic jig
Disinfect the jig according to normal procedures for
non-autoclavable products.
18 All-on-4® treatment concept manual // Guided surgery

Clinical procedure

The images show Immediate Function with an all-acrylic bridge and NobelSpeedy Groovy RP implants in the maxilla.
The same procedure also applies for the mandible.

1 Place implants
– Place four implants according to the computer-based
planning.
– Remove the surgical template.

2 Connect straight Multi-unit Abutments

– If indicated use a Bone Mill to correctly seat the
abutments.
– Place straight Multi-unit Abutments in the two
anterior sites.

– Tighten to 35 Ncm using Screwdriver Machine

Multi-unit and Manual Torque Wrench Prosthetic.

3 Place jig to connect 30° Multi-unit Abutments

– Place the disinfected jig on the corresponding anterior
abutment and posterior implant.
– Verify correct seating of the jig and tighten the guide pin
to the anterior abutment.
 All-on-4® treatment concept manual // Guided surgery 19

4 Connect and tighten 30° Multi-unit Abutment

– Connect the 30° Multi-unit Abutment Non-Engaging and
abutment screw using Unigrip Screwdriver.
– Tighten the abutment screw to 15 Ncm using Screwdriver
Machine Unigrip and Manual Torque Wrench Prosthetic.

5 Disconnect jig
– Disconnect the jig by unscrewing the abutment holder (1)
and guide pin (2).
– Repeat the entire procedure for the opposite side.

Note: Never unscrew the abutment holder connected to

the 30° Multi-unit Abutment before tightening the posterior 1
angled abutment.
2

Option: delayed loading

If the required tightening torque for Immediate Function
(minimum 35 Ncm) cannot be achieved or the treatment of
choice is a delayed loading protocol, a conventional healing
phase is recommended prior to delivery of a provisional or
final restoration.

– Place cover screws on all four implants and suture the en-
trance to the implants or close the flap in case it was raised.
– Wait with further steps until osseointegration has taken
place.
20 All-on-4® treatment concept manual // Guided surgery

7 Connect temporary copings

Notes:
– The all-acrylic bridge is delivered with Temporary Copings
Multi-unit Titanium in three implant positions. There is an
extended hole located in one of the posterior positions.
– If the treatment team is not experienced with the proce-
dure, it is recommended to leave two extended holes
in the all-acrylic bridge.

– Place the Temporary Coping Multi-unit Titanium that is not

yet connected to the prosthesis onto its corresponding
Multi-unit Abutment and manually tighten using Unigrip
Screwdriver.

– Connect the bridge using three prosthetic screws and

manually tighten using Unigrip Screwdriver.
– Tighten all screws to 15 Ncm using Unigrip Screwdriver
Machine and Manual Torque Wrench Prosthetic.

–U
 se tooth-colored flowable composite or acrylic to secure
the temporary coping to the bridge, making sure to keep
the screw-access hole free from composite.
 All-on-4® treatment concept manual // Guided surgery 21

8 Reinforce temporary coping

– Disconnect the bridge.
– Fill the gap between temporary coping and the
bridge with self-curing acrylic.
– Adjust and polish.

9 Connect provisional bridge

– Place the all-acrylic bridge on the abutments.
– Tighten the prosthetic screws to 15 Ncm using
Unigrip Screwdriver Machine and Manual
Torque Wrench Prosthetic.
– Block out screw access and fill holes with suitable material.
– Check the occlusion.

10 Final restoration
After adequate healing time, follow established prosthetic
procedures for the final restoration, preferably using a
NobelProcera Implant Bridge.
22 All-on-4® treatment concept manual // Guided surgery

Laboratory procedure – fabrication of

model and abutment connection

1 Fabricate stone model and surgical index

– Fabricate a stone model using the surgical template as
described in the NobelGuide concept manual.
– Mount the model in the articulator using the radiographic
guide.
– Replace the radiographic guide with the surgical template.
– Fabricate a surgical index towards the opposing dentition
in the articulator.
– Put the surgical template back in the UV-protective plastic
bag in which it was delivered.

2 Connect straight Multi-unit Abutment

– Place the selected straight Multi-unit Abutment on
the anterior implant replica. Remove the plastic holder.
– Tighten with Screwdriver Manual Multi-unit.

Note: Plastic Try-in Multi-unit Abutments are available to

determine the ideal abutment collar height prior to ordering/
opening the final Multi-unit Abutment package.

3 Place 30° Multi-unit Abutment Non-Engaging

– Place a 30° Multi-unit Abutment Non-Engaging (1)
including jig stabilizer (2, modified Impression Coping
Open Tray Multi-unit), abutment holder (3) and 3
abutment screw (4) on a posterior implant replica.
– Align the abutment holder with the long axis of the
straight Multi-unit Abutment.
– Tighten the abutment screw with Unigrip Screwdriver 2
Manual.
4

4 Disconnect jig stabilizer

– Disconnect the jig stabilizer by unscrewing the
abutment holder.
– Repeat steps 2–4 for the opposite side.

Note: Once the abutments are tightened in their final

position, do not loosen them until the jig is fabricated.
 All-on-4® treatment concept manual // Guided surgery 23

Laboratory procedure – fabrication of

all-acrylic bridge

1 Place temporary copings

– Use guide pins or lab screws to place three Temporary
Copings Multi-unit Titanium on the two anterior and on
one of the posterior abutments.
– Adjust the copings if needed.

Note: If the treatment team is not experienced with the

procedure, it is recommended to leave two extended holes
in the all-acrylic bridge.

2 Fabricate all-acrylic bridge

– Fabricate an all-acrylic bridge using a high-density acrylic.
– Remember to reinforce the weak points of the prosthesis
around the cylinders with more acrylic.

Note: If applicable, the provisional prosthesis can be made

by converting the existing denture into a bridge.

3 Drill hole through bridge

Drill through the bridge where the fourth Temporary Coping
Multi-unit Titanium will be positioned. Make sure that the
hole is larger than the coping.

4 Try-in fourth temporary coping

Try-in the temporary coping and adjust if necessary.
24 All-on-4® treatment concept manual // Guided surgery

Laboratory procedure –
fabrication of jig

1 Place impression coping

– Place an Impression Coping Open Tray Multi-unit on one
of the straight Multi-unit Abutments.
– Tighten the guide pin using Unigrip Screwdriver Manual.

2 Reconnect jig stabilizer

– Reconnect jig stabilizer and abutment holder on the 30°
Multi-unit Abutment Non-Engaging.
– Align the abutment screw access hole with the abutment
screw.

3 Secure jig stabilizer

Use thin wire or dental floss to secure jig stabilizer and
impression coping.

4 Apply acrylic
Use quick-setting acrylic to secure the wire/floss between
jig stabilizer and the impression coping.

Note: Avoid putting acrylic on the abutments.

 All-on-4® treatment concept manual // Guided surgery 25

5 Remove jig
– Loosen, but do not remove, the guide pin from the straight
Multi-unit Abutment.
– Loosen the abutment screw securing the 30° Multi-unit
Abutment to the implant replica.
– Remove the jig from the stone model.

Note: All components must remain connected in the jig

construction.

6 Repeat procedure
Repeat the procedure for the other two abutments.

7 Disconnect straight Multi-unit Abutments

– Disconnect the straight Multi-unit Abutments from the
model using Screwdriver Manual Multi-unit.
– Mount the plastic holder back onto the abutment in order
to facilitate abutment connection for the clinician.

8 Send the following to the clinician

– Stone model.
– Two jigs (marked ‘Left’ and ‘Right’) including angled
Multi-unit Abutments.
– Two straight Multi-unit Abutments.
– Temporary bridge with three Temporary Copings Multi-unit
cured within temporary restoration.
– One loose Temporary Coping Multi-unit.
– 4 prosthetic screws.
– Surgical template with verified fit on model.
– Surgical index.
26 All-on-4® treatment concept manual // Product information

Final restorations

It is recommended to use the highly esthetic and versatile

NobelProcera Implant Bridge as final prosthetic reconstruction.
Several veneering options are available, depending on patient
needs and requirements:

Basic: NobelProcera Implant Bridge with acrylic teeth

and acrylic gingiva
Acrylic teeth with acrylic gingiva applied over the
NobelProcera titanium framework.
Premium bridge for the maxilla

Medium: NobelProcera Implant Bridge veneered with

composite
NobelProcera titanium framework veneered with composite
for good esthetics and easy repair (both chair-side and in lab).

Premium: NobelProcera Implant Bridge with individual-

ized NobelProcera ceramic crowns
Individual NobelProcera Crowns Alumina or Zirconia
cemented to a NobelProcera Implant Bridge framework
for excellent esthetics and strength.
Basic bridge for the mandible

For the prosthetic procedure, see NobelEsthetics procedures

manual (for the current version see nobelbiocare.com/resources).

Intra-oral bite

Extra-oral smile

Case courtesy of MALO CLINIC Lisbon (Portugal) and

CM Ceramics
 All-on-4® treatment concept manual // Product information 27

Multi-unit Abutments

For multiple-unit, screw-retained restorations

Short cone for limited

interocclusal space.

Designed to accommodate fully

and partially edentulous arches,
particularly when using the
All-on-4® treatment concept.
Wide shoulder for easy
positioning of the prosthetic
restoration for a secure
passive fit.
Available as straight and angled
(17º and 30º), engaging and non-
engaging*, with a selection of
Each Multi-unit Abutment is delivered collar heights.
with a pre-mounted holder for easy
handling, which doubles as a guide
for checking abutment angulation.

*For guided surgery only.

28 All-on-4® treatment concept manual // Product information

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

1 mm
1 mm

Multi-unit Abutment 1 
mm 29176 29179 29184 – – – 29196 29199 29204 –

1.5 mm

Multi-unit Abutment 1.5 

mm – – – 36611
36616
37829 – – – –

2 mm
2 mm

Multi-unit Abutment 2 
mm 29177 29180 29185 – – – 29197 29200 29205 –

2.5 mm

Multi-unit Abutment 2.5 

mm – – – 36613
36617
37830 – – – –

3 mm
3 mm

Multi-unit Abutment 3 
mm 29178 29181 29186 – – – 29198 29201 29206 –

3.5 mm

Multi-unit Abutment 3.5 

mm – – – 36624
36625
37831 – – – –

4 mm
4 mm

Multi-unit Abutment 4 
mm – 29182 – – – – – 29202 – –

4.5 mm

Multi-unit Abutment 4.5 

mm – – – – 36626 – – – – –

5 mm
5 mm

Multi-unit Abutment 5 
mm – 29183 – – – – – 29203 – –

0.5 mm

Adapter NobelReplace® 6.0 to WP

(add 0.5 mm to abutment height) – – – – – – – – – 32412

Clinical screw included.

 All-on-4® treatment concept manual // Product information 29

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

2 mm

2 mm

17° Multi-unit Abutment 2 

mm 29187
29189 – – – – 29235
29237 – –

2.5 mm

17° Multi-unit Abutment 2.5 

mm – – – 36614
36618
37832 – – – –

3 mm
3 mm

17° Multi-unit Abutment 3 

mm 29188
29190 – – – – 29236
29238 – –

3.5 mm

17° Multi-unit Abutment 3.5 

mm – – – 36615
36619
37833 – – – –

4 mm
4 mm

17° Multi-unit Abutment 4 

mm – 29191 – – – – – 29239 – –

3.5 mm

30° Multi-unit Abutment 3.5 

mm – – – 36620
36622 – – – – –

4 mm
4 mm

30° Multi-unit Abutment 4 

mm – 29192 – – – – – 29240 – –

30° Multi-unit Abutment

Non-Engaging 4 mm 4 mm 4 mm

(For All-on-4® treatment

concept with guided surgery)* – 33411 – – – – – 33409 – –

4.5 mm

30° Multi-unit Abutment 4.5 

mm – – – 36621
36623 – – – – –

5 mm
5 mm

30° Multi-unit Abutment 5 

mm – 29193 – – – – – 29241 – –

30° Multi-unit Abutment

Non-Engaging 5 mm 5 mm 5 mm

(For All-on-4® treatment

concept with guided surgery)* – 33412 – – – – – 33410 – –

Clinical screw included.

* Abutment Holder, Jig Stabilizer and clinical screw included (see page 16).
30 All-on-4® treatment concept manual // Product information

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

Abutment Screw Multi-unit Angled 29194 29195 – 36892 37893 37893 29242 29243 – –

Prosthetic Screw Multi-unit 29285 29285 29286 29285 29285 29285 29285 29285 29285 –

4.1 mm 4.1 mm 4.1 mm

Healing Cap Multi-unit (1/pkg) 31145 31145 29066 31145 31145 31145 31145 31145 31145 –

4.1 mm 4.1 mm 4.1 mm

Healing Cap Multi-unit (5/pkg) 29064 29064 – 29064 29064 29064 29064 29064 29064 –

4.1 mm 4.1 mm 4.1 mm

Healing Cap Wide Multi-unit (1/pkg) 31146 31146 29067 31146 31146 31146 31146 31146 31146 –

Torque guide for clinical screws for Nobel Biocare implant systems

Straight Multi-unit Abutment 35 Ncm

17° and 30° Multi-unit Abutment 15 Ncm
Prosthetic screw 15 Ncm
 All-on-4® treatment concept manual // Product information 31

Surgical components

Bone Mills and Guides Brånemark System®

Bone Mill with Guide NP ∅ 4.5 mm 33392
Bone Mill with Guide RP ∅ 5.1 mm 33393
Bone Mill with Guide WP ∅ 6.5 mm 33495
Bone Mill Guide NP 33496
Bone Mill Guide RP 33497
Bone Mill Guide WP 33498

Bone Mills and Guides Conical Connection

Bone Mill with Guide NP ∅ 4.4 mm 37863
Bone Mill with Guide NP ∅ 5.2 mm 37864
Bone Mill with Guide RP ∅ 5.2 mm 37866
Bone Mill with Guide RP ∅ 6.2 mm 37867
Bone Mill with Guide WP ∅ 6.7 mm 37869
Bone Mill Guide NP 37865
Bone Mill Guide RP 37868
Bone Mill Guide WP 37870

Bone Mills and Guides NobelReplace®

Bone Mill with Guide NP ∅ 4.6 mm 36830
Bone Mill with Guide RP ∅ 5.3 mm 36831
Bone Mill with Guide WP ∅ 6.5 mm 36832
Bone Mill with Guide 6.0 ∅ 7.0 mm 33505
Bone Mill Guide NP 36608
Bone Mill Guide RP 36609
Bone Mill Guide WP 36610
Bone Mill Guide 6.0 33509

All-on-4® Guide 32068

32 All-on-4® treatment concept manual // Product information

Prosthetic Kit 37448

(The articles below can also be purchased individually.)

Kit includes
Screwdriver Machine Unigrip™ 20 mm 29151
Screwdriver Machine Unigrip™ 30 mm 29153
Screwdriver Machine Multi-unit 21mm 29158
Omnigrip™ Screwdriver Machine 20 mm 37379
Omnigrip™ Screwdriver Machine 30 mm 37381
Manual Torque Wrench Prosthetic 29165

Screwdrivers
Screwdriver Manual Unigrip 36 mm 29150

Screwdriver Manual Multi-unit 25 mm 29156

Screwdriver Manual Multi-unit
Brånemark System® WP 25 mm 29157

Screwdriver Machine Multi-unit 21 mm 29158

Screwdriver Machine Multi-unit
Brånemark System® WP 20 mm 29159

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

**10 mm
11 mm 11 mm
*11 mm
Impression Coping Open Tray Multi-
unit (includes 15 
mm Guide Pin) 29089* 29089* 29091** 29089 29089 29089 29089 29089 29089 –
 All-on-4® treatment concept manual // Product information 33

Laboratory components

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

Temporary Coping Multi-unit

Titanium (with Prosthetic Screw) 29046 29046 29047 29046 29046 29046 29046 29046 29046 –

Abutment Replica Multi-unit (1/pkg) 31161 31161 31162 31161 31161 31161 31161 31161 31161 –

Abutment Replica Multi-unit (5/pkg) 29110 29110 – 29110 29110 29110 29110 29110 29110 –

Guide Pin Multi-unit 10 

mm (1/pkg) 31154 31154 31156 31154 31154 31154 31154 31154 31154 –

Guide Pin Multi-unit 10 

mm (5/pkg) 29102 29102 – 29102 29102 29102 29102 29102 29102 –

Guide Pin Multi-unit 20 

mm (1/pkg) 31155 31155 31157 31155 31155 31155 31155 31155 31155 –

Guide Pin Multi-unit 20 

mm (5/pkg) 29103 29103 – 29103 29103 29103 29103 29103 29103 –
34 All-on-4® treatment concept manual // Product information

External hex Internal conical Internal tri-channel

connection connection connection
Brånemark System® and NobelActive®, NobelParallel™ and NobelReplace®, Replace Select™,
NobelSpeedy® Groovy NobelReplace® Conical Connection NobelSpeedy® Replace,
NobelReplace® Platform Shift

NP RP WP NP RP WP NP RP WP 6.0

Lab Screw Multi-unit (1/pkg) – – 31163 – – – – – – –

Lab Screw Multi-unit (5/pkg) 29287 29287 – 29287 29287 29287 29287 29287 29287 –

Lab Screw Multi-unit Angled (1/pkg) 37896 37897 – 37896 37897 37897 31166 31167 – –
 All-on-4® treatment concept manual // Appendices 35

Clinical cases

Efficient treatment with NobelSpeedy

44-year old edentulous female patient requests a fixed restoration due to
inadequate function, comfort and esthetics of the existing removable denture.

Diagnosis
Limited bone volume in the posterior and a need for
bone crest level optimization.

Preparation
A conventional flap procedure is performed, the bone
crest level optimized and the All-on-4® Guide anchored.

Implant site preparation

Implant site preparation according to the drilling protocol
for straight implants using the All-on-4® Guide. The vertical
lines on the guide are used as reference for drilling at an
angle of 45°.

Implant insertion
Insertion of NobelSpeedy Groovy implants with external
hex connection.

Provisional prosthesis
Immediate loading of the implants with fixed provisional
prosthesis based on an impression taken straight after
surgery.

Case courtesy of Paulo Malo, DDS, PhD,

MALO CLINIC Lisbon, Portugal
36 All-on-4® treatment concept manual // Appendices

Achieving predictable results with NobelGuide

Indication
63-year old edentulous female patient requests a fixed
restoration. The transition zone is completely hidden above
the smile line.

Chairside diagnosis
The All-on-4® treatment concept using NobelGuide is cho-
sen using a minimally invasive flapless approach (adequate
mouth opening is possible).

Preparation
The existing removable denture represents the intended
tooth setup and is transformed into a radiographic guide
(gutta percha markers). A bite index is created to ensure
correct anatomical positioning of the guide during CT
scanning.

Treatment planning
Based on 3D CT diagnostic imaging of patient and radio-
graphic guide, the four implants are placed virtually in the
NobelClinician Software, optimizing position, angulation
and distribution.

Implant site preparation

After careful installation of the ready-to-use surgical
template and soft tissue punching, guided drilling for
the first anterior implant is performed according to the
NobelGuide drill protocol for NobelSpeedy implants.
 All-on-4® treatment concept manual // Appendices 37

Implant insertion
The first anterior NobelSpeedy Groovy implant is inserted
into the prepared site. After proper seating, the second
anterior implant site gets prepared and the implant inserted.
Preparation and insertion of the distal implants is only per-
formed after full seating of the two anterior implants.

Minimally invasive surgery

If a flapless procedure is chosen, trauma to tissue is mini-
mized. This image shows the maxillary arch immediately
after implant insertion.

Provisional prosthesis
A fixed prosthesis fabricated prior to surgery is finalized in
the patient’s mouth and secured with four prosthetic screws
(with Multi-unit Abutments installed on the implants and
Temporary Copings Multi-unit within the prosthesis).

Immediate Function
As immediate loading is part of the treatment plan, the
patient benefits from a fixed, screw-retained prosthesis
immediately after surgery.

Final restoration
After adequate healing time, a final NobelProcera Implant
Bridge is fabricated based on a new impression.

Case courtesy of Paulo Malo, DDS, PhD,

MALO CLINIC Lisbon, Portugal
38 All-on-4® treatment concept manual // Appendices
 All-on-4® treatment concept manual // Appendices 39

Customer service worldwide

Americas Europe, Middle East and Africa Russia

Brazil Austria Nobel Biocare Russia

Nobel Biocare Brazil Nobel Biocare Austria Phone: +7 495 974 77 55

Phone: 0800 16 999 6 Phone: +43 1 892 89 90 South Africa

Canada Belgium Nobel Biocare South Africa

Nobel Biocare Canada Nobel Biocare Belgium Phone: +27 11 802 0112

Phone: +1 800 939 9394 Phone: +32 2 467 41 70 Spain

Chile Denmark Nobel Biocare Spain

Dental Biocare Nobel Biocare Denmark Phone: +34 900 850 008

Phone: +56 220 19282 Phone: +45 39 40 48 46 Sweden

Colombia Finland Nobel Biocare Sweden

Hospimedics S.A. Nobel Biocare Finland Phone: +46 31 335 49 00

Phone: +57 1 640 0608 Phone: +358 20 740 61 00 Switzerland

Mexico France Nobel Biocare Switzerland

Nobel Biocare Mexico Nobel Biocare France Phone: 0800 211 424

Phone: +52 55 524 974 60 Phone: +33 1 49 20 00 30 United Kingdom

USA Germany Nobel Biocare UK

Nobel Biocare USA Nobel Biocare Germany Phone: +44 208 756 3300

Phone: +1 800 322 5001 Phone: +49 221 500 850

Hungary
Distributor markets
Nobel Biocare Hungary
Asia Pacific Phone: +36 1 279 33 79 Algeria, Bulgaria, Croatia, Cyprus,

Australia Czech Republic, Greece, Jordan, Kuwait,

Ireland
Nobel Biocare Australia Lebanon, Malta, Romania, Saudi Arabia,
Nobel Biocare Ireland
Phone: 1800 804 597 Serbia, Slovenia, Tunisia, Turkey,
Phone: 1800 677 306
United Arab Emirates
China Italy Phone: +34 933 560 562
Nobel Biocare China Nobel Biocare Italy
Phone: +86 21 5206 6655 Phone: +39 800 53 93 28
Hong Kong Lithuania
Nobel Biocare Hong Kong Nobel Biocare Lithuania
Phone: +852 2845 1266 Phone: +370 5 268 3448
India Netherlands
Nobel Biocare India Nobel Biocare Netherlands
Phone: 1800 266 9998 Phone: +31 30 635 49 49
Japan Norway
Nobel Biocare Japan Nobel Biocare Norway
Phone: +81 3 6717 6191 Phone: +47 64 95 75 55
New Zealand Poland
Nobel Biocare New Zealand Nobel Biocare Poland
Phone: 0800 441 657 Phone: +48 22 549 93 52
Singapore Portugal
Nobel Biocare Singapore Nobel Biocare Portugal
Phone: +65 6737 7967 Phone: +351 800 300 100
Taiwan
Nobel Biocare Taiwan
Phone: +886 080 00 779

nobelbiocare.com/contact

v 16.1
nobelbiocare.com
79360 B GB 1610 Printed in the EU © Nobel Biocare Services AG, 2015. All rights reserved.
Nobel Biocare, the Nobel Biocare logotype and all other trademarks are, if nothing else is stated or is evident from the context in a certain case, trademarks of Nobel Biocare.
Please refer to nobelbiocare.com/trademarks for more information. Product images are not necessarily to scale.