Ra 1 020 Ep242 11001 Piping Material Specification 1

p0SCO TECHNICAL SPECIFICATION D
oc. No.:
RA1020-EP242-11001
Rev. 2
Technical Specification for

Piping Materials
PROJECT NAME POSCO SNG PROJECT

PEC PROJECT CODE A70452EA
PEN JOB NO. 080241
CLIENT POSCO
LOCATION GWANGYANG, KOREA
II 1
3 Jan.
2 For Construction C.H.Yang B.W.Lim - / S.M.Pa
2014
25 Oct.
1 For Construction B.H.Ahn - .S.Park
2012
23 Feb.
0 For Construction B.H.Ahn - .S.Park
2012
29 Sep.
R For Approval C.H.Yang B.H.Ahn - Y.S.Park
2011
18 May
For Approval C.H.Yang B.H.Ahn - S.R.Lee
2011
Rev.
Date Description Prepared Checked Reviewed Approved
No.
This DOCUMENT is the property of POSCO ENGINEERING. Therefore, it shall not be released to any third party without
permission of an authorized personnel of POSCO ENGINEERING.
pose° posca
E&C ENGINEERING
TECHNICAL Doc. No. Rev. No. Page
RA-1-020-
SPECIFICATION EP242-11001
2 1/28
CONTENTS
1.0 GENERAL 2
1.1 INTRODUCTION 2
1.2 PURPOSE 2
2.0 REFERENCES 2
2.1 CODES AND STANDARDS 2
2.2 FEED DOCUMENTS 3
3.0 PIPING DESIGN 3

3.1 ENGINEERING DESIGN 3
3.2 PIPE THICKNESS CALCULATION 4
3.3 STRUCTURAL CALCULATION 4
3.4 BRANCH CALCULATION 5
4.0 PLANT DESIGN 5

4.1 GENERAL 5
4.2 PIPING ABOVE GROUND LEVEL 5
4.3 CLEARANCE AND ACCESSIBILITY 6
4.4 BURIED PIPING 6
4.5 PIPE TRACKS AND PIPE TRENCHES 7
4.6 PIPING PENETRATIONS 7
4.7 SMALL BORE PIPING 8
4.8 INSTALLATION OF FLANGES 8
4.9 PROCESS PIPING 9
4.10 PIPING ADJACENT TO EQUIPMENT 15
4.11 UTILITY PIPING 18
4.12 INSTRUMENT PIPING 19
5.0 MATERIALS 22
5.1 GENERAL 22
5.2 MATERIALS OF CONSTRUCTION 22
5.3 PIPING COMPONENTS 25
ATTACHMENT #1: (Piping Line Classes and Summary)

RA-1-020-
2 2/28
1.0 GENERAL
1.1 Introduction
This document outlines the piping specification standards and material requirements for the
POSCO Synthetic Natural Gas (SNG) plant, to be constructed in Gwangyang-si, Jeollanam-do,
South Korea.
1.2 Purpose
The purpose of this document is to define the piping specification design criteria and identify the
codes, standards, methods and procedures to be used to execute the piping engineering design
for the POSCO SNG project.
2.0 REFERENCES
2.1 Codes and Standards
The Standards and Publications used for the design of pipework and layout of Plant on this
project shall be as follows;
ASME B31.1 Power piping.
ASME B31.3 Process piping.
ASME B16.5 Pipe flanges and flanged fittings.
ASME B16.9 Factory-made wrought buttwelding fittings.
ASME B16.10 Face-to-face and end-to-end dimensions of valves.
ASME B16.11 Forged fittings, socket-welding and threaded.
ASME B16.24 Cast Copper Alloy Pipe Flanges and Flanged Fittings Classes 150,
300, 600, 900, 1500, and 2500.
ASME B16.34 Valves - flanged, threaded, and welded End.
ASME B16.47 Large diameter steel flanges NPS 26 through NPS 60.
ASME B36.10M Welded and seamless wrought steel pipe.
ASME B36.19M Stainless Steel Pipe.

RA-1-020-
2 3/28
API 600 Steel Gate Valves-Flanged and Butt-welding Ends, Bolted Bonnets
API 602 Steel Gate, Globe, and Check Valves for Sizes NPS 4 (DN 100) and
Smaller for the Petroleum and Natural Gas Industries.
API 607 Fire test for soft-seated quarter turn valves.
CGA G-4.4 Oxygen Pipeline Systems (EIGA Doc 13/02)
SP-25 Standard marking system for valves, fittings, flanges and unions.
NACE MR0175 Materials resistant to sulfide stress cracking in corrosive petroleum

refining environments.
2.2 Specifications
RA-1-020-EP241-11004 Piping Job Instruction.
2.3 Feed Documents
RA-1-020-EP400-10001 Piping Line Classes and summary.
RA-1-020-EP400-10014 Piping Line Classes addendum.
RA-1-020-EP242-10002 Piping Specification.
3.0 PIPING DESIGN
3.1 Engineering Design
The following pipe sizes shall be used:
DN15, DN20, DN25, DN40, DN50, DN80, DN100, DN125, DN150, DN200, DN250, DN300,
DN350, DN400, DN450, DN500 and DN600 (or the inch series equivalent) with the following
restrictions:
Sizes DN15 and DN20 shall not be used for long-run piping due to their vulnerability to
damage and limited mechanical strength.
Sizes less that DN50 shall not be used in pipe tracks.
Sizes less that DN40 shall not be used on pipe racks.
Size DN125 will only be used if specifically specified by Licensors.
The range of pipe sizes above DN600 shall be restricted to DN1600.
Piping shall be designed for the most onerous or severe combination of coincident conditions
stated on the process line list. Moreover, fault, transient or occasional conditions may also need to
be considered. These can include, but may not be limited, to the following:
RA-1-020-
2 4/28
Steaming-out pressures and temperatures
Pressure surge
Water hammer
Pump shut-off pressure
Static pressure
Pressure drop
Vacuum caused by cooling and possible condensing of trapped medium
Steam/nitrogen purge pressure
In situations where different design conditions exist in one piping system, different piping
classes may need to be used. In these cases specification “breaks" shall be located on P&ID’s
such that the more severe design condition may never occur in the part of the system with the
lower rated piping class. Specification breaks between piping classes of different ratings and / or
materials shall generally be flanged connections.
Where in-line equipment (e.g. control valves) with a higher rating than the general pipe is fitted,
the connecting flanges shall have the same rating as the higher rated in-line equipment but may
have the same wall thickness as the pipe.
If a system operating above 0 °C is connected to a system operating at 0 °C or below, the first

length section, equivalent to 50 times the pipe diameter of the higher temperature system (with
a maximum of 10 m) shall be designed to the specifications of the lower temperature system.
Piping subject to sub-atmospheric pressure shall be designed for full vacuum.
The minimum wall thickness for pipes, shall be in accordance with ASME B31.3.
3.2 Pipe Thickness Calculation
Straight Pipe calculation to ASME B31.3 (Pipemill) is used to determine the minimum wall
thickness plus tolerance and corrosion allowances.
Thickness calculation is run for both ends of the Temperature/Pressure limits shown on each
Pipe Class. The conditions giving the highest thickness values are chosen and the
corresponding thickness, pressure, temperature and stress values are then used in the
structural and Branch calculations to follow.
These figures are used as a basis to select a suitable pipe thickness based on the nearest
standard wall thickness from ASME B36.10M and B36.19M.
3.3 Structural Calculation

RA-1-020-
2 5/28
The calculated thickness and selected thickness values derived from the straight pipe
calculation are used in the structural calculation. If the schedule/thickness of pipe chosen fails
the structural test then the next available schedule/thickness above is to be selected to satisfy
the structural check.
Piping wall thickness selection shall be governed by the greater of minimum calculated code
thickness including tolerance and corrosion allowance or the minimum structural thickness
provided in Table 1, plus corrosion allowance.
Table 1 - Minimum structural pipe wall thickness (Ts)
Nominal pipe size Welded pipe including Threaded pipe

seal/socket welded (Not seal welded)
DN15 to 40 2.25mm 3.0mm
DN50 to 80 2.25mm 3.0mm
DN100 to 300 2.54mm -
DN350 to 450 3.0mm -
DN500 to 1600 D/150 (1) -
Note (1): “D” is the pipe outside diameter.
3.4 Branch Calculation
The thickness used in the branch calculation is the final thickness selected after completing the
structural calculation. The pressure, temperature and stress values used are the same as those
selected in the pipe thickness check.
4.0 PLANT DESIGN
4.1 General
Equipment shall be located and pipework routed such that the optimum layout is achieved with
due regard to process requirements, aesthetics, ergonomics, economics, operation, inspection
and maintenance, whilst providing wherever reasonably practicable, an inherently safe design.
Having considered the major factors, the number of flanges, fittings, valves and welds shall be
minimised.
4.2 Piping above Ground Level
Piping generally shall be routed above ground level.

RA-1-020-
2 6/28
Wherever reasonably practicable, piping entering and leaving a plot area or a processing unit
shall be grouped together.
Wherever reasonably practicable, inside-plot piping shall be routed on overhead pipe racks. The
smallest allowable pipe size on pipe racks is DN40. Piping smaller than DN40 can be increased in
size for rack runs when increased risk of internal corrosion is not a consideration. If the pipe size
cannot be increased then additional supports, to limit the span, shall be provided.
Piping within pipe racks shall be arranged so as the heaviest and/or the hottest pipes are
located at the sides of the pipe rack to provide space for expansion loops and to reduce the
moments in the beams caused by the weight and thermal expansion of the pipes.
The minimum distance between pipes or the insulation of pipes shall be 50 mm.
The minimum distance between a flange and a pipe or the insulation of a pipe shall be 40 mm. The
minimum clearance between the outside diameter of pipe and structural member or similar
obstruction shall be 50 mm.
Where required, the distance between pipes shall be increased to allow for movements caused by
thermal expansion.
The distance between the insulation of a low-temperature pipe and any other object shall be at
least 100 mm.
The distance between pipes shall allow for the turning of a spectacle blind, if present.
Pipe routings and crossings shall be on different, predetermined elevations.
Where possible, complicated crossings should be avoided by good piperack design.
Piping with instrument connections shall be routed so that safe access to these connections is
ensured; if necessary, platforms or walkways shall be provided.
Where multiple nozzles are applied (e.g. on air cooler banks) the connecting piping shall be
designed so that small dimensional errors in construction can be accommodated.
Safety relief valve discharge piping shall be designed to withstand the dead loads and the blowoff
loads. Blow-off design loads shall take into account the most severe case, such as possible
flashing conditions and liquid entrainment in vapour flows.
4.3 Clearance and Accessibility
See Document No.RA-1-020-EP241-11004 ‘Piping Job Instruction’.
4.4 Buried Piping
Buried piping shall be considered for:

RA-1-020-
2 7/28
drainage or sewage;
fire water and other water pipes (for protection against heat or frost);
large-diameter pipes (e.g. main cooling water pipes & sea water);
Natural gas
Minimum cover of soil for buried pipe shall be as specified in Civil, Architectural, and Building
Services Basis of Design document No.RA-1-040-EC240-10002.
If need, any load on pipes crossing under roads should be equalised, e.g. by means of
concrete encasement, pipe sleeves or a culvert. The pipes shall be kept centrally in the sleeves by
welded spacers.
Soil settlement and thermal expansion of the piping shall be taken into account in the design of
underground piping.
Co-ordination of underground services shall ensure sufficient separation from electrical or

instrument cables.
Piping shall be designed so that the complete system can be flushed and cleaned. (e.g. “dead
ends” should be avoided).
4.5 Pipe Tracks and Pipe Trenches
Piping runs that are not on piperacks or buried, generally outside of process units (e.g. offsite
areas), should be supported on sleepers at ground level in pipe tracks or below ground level in
pipe trenches. The choice between pipe tracks or pipe trenches should be determined by
technical and economic considerations, e.g. the number of road crossings, the ground water
level and the length of the required trench.
Grade level piping shall be run so as not to restrict access where required.
The elevation of the sleepers shall be such that there is access for maintenance and for
operation of valves, drains and instrumentation, and that pipes and insulation will remain above
the highest expected storm water levels.
Flanged connections shall not be installed in trenches, in order to prevent the accumulation of
gas and liquid vapours in the trenches.
Concrete trenches in process units shall be adequately drained into a liquid-sealed drainage
system and shall be covered with grating.
4.6 Piping Penetrations

RA-1-020-
2 8/28
Sleeves or holes through walls and floors of buildings shall have a size permitting the passage of
a flange of the relevant pipe size, or the size of the required insulation, whichever is the larger, to
allow the installation of prefabricated piping.
To prevent liquid dripping onto a lower deck, holes shall be provided with concrete curbs, cast-in
extended pipes or other means. Where applicable the fire rating of the wall or floor shall be
maintained.
4.7 Small Bore Piping
Since small bore branches (DN40) to large bore piping are relatively susceptible to failure, the
following points shall be incorporated in the piping design to minimize the risk of vibration
induced fatigue:
Minimise the number of small bore branches to piping.
All small bore nozzle welding shall be performed by Gas Tungsten Arc Welding (GTAW) in
the fabrication shop.
Small bore piping shall be shown in full detail, on the isometric drawings.
Branches shall not be located in removable spools, unless it is impractical to do otherwise.
Branches shall not be located in high stress areas.
Branches shall be avoided downstream of high capacity gas pressure reducing systems
such as compressor recycle systems, steam desuperheaters, high-rate depressuring valves
and safety relief valves. If this is not possible, branches shall be located well away from
these sources of vibration.
In branches with flanged valves, branch fittings with flanged outlets shall be used wherever
possible, in order to reduce the number of welds.
Small bore connections such as vent, drain and pressure indicator connections should be
braced to improve mechanical strength and resist problems associated with imposed
vibration.
Un-reinforced welded branch connections should be avoided in high pressure/temperature or

critical/toxic services.
4.8 Installation of Flanges
Flanges in piping systems shall be installed only to facilitate maintenance and inspection and
where construction or process conditions dictate.
Flanges shall not be located above roads.
Flanges shall be bored to match pipe.

RA-1-020-
2 9/28
Flanges shall not be used in pipe trenches.
4.9 Process Piping
4.9.1 Gasification - Licensor Specific Requirements
The gasification licensor has offered design guidance notes throughout the P&ID’s and
material selection guidelines for the following services;
A. High Pressure concentrated slurry
B. High pressure intermittent slurry
C. Low pressure concentrated slurry
D. Highly erosive slag slurry (basalt-lined)
E. Highly erosive slurry (stainless steel)
F. High pressure general syngas
G. Recycled char
See Table 4.9.2 for a summary of specific licensor design guidance.
4.9.2 Tabulation of Gasification Design Guidance
Notes A B C D E F G
Material shall be grade 304/304L. X X X X X
Pipe bends shall be used in lieu of elbows.

Pipe bend radius should be three times the X X X X X X
nominal pipe diameter or greater (i.e., ≥3D).
Control valves shall not be used in these X X X X X

services.
Ball valves should have the bore of the ball in

precise alignment with the bore of the valve
body when in the fully open position and the X X X X X X X
bore of the ball perpendicular to the bore of
the valve body when in the fully closed
position.
Pressure sensors shall be of the non-intrusive, X X X

sealed diaphragm type.
Well-insulated, external surface-mount

thermocouples should be used. Non- intrusive
thermowell / thermocouple combinations X X X X X X X
should be used (unless otherwise noted on the
P&IDs.
Threaded joints should not be permitted. X X X X X X

RA-1-020-
2 10/28
Notes A B C D E F G
Minimum pipe size for in-line piping should be

DN50. Minimum branch connections for X X X
drains, sample connections, etc. should be
DN25.
The arrangement of piping and valves used for

flushing shall be designed to omit dead-legs X X X
and to ensure that all piping is flushed.
Flush connections should enter the top of the

line and drain connections should be on the
bottom of the pipe. Isolation valves for flush X X X
and drain connections should be piped
fittingto-fitting to the line to be flushed.
Flush line flange face projections from the

process piping should be held to a minimum X X X
distance.
Flush connections should be located as close

to the upstream process block valve as X X X
possible, and drain connections as close to the
downstream equipment as possible.
Provision to be made for hydro-lancing of the X X X

slurry piping.
Clean out connections should be placed at the

center of the outside radius of long radius X X X
bend (elbows) to hydro-lance the slurry piping
in both directions.
Piping layout shall be designed:

To minimize erosion from changes in flow
direction.
X X X
To minimize dead-legs and avoid
plugging.
To facilitate easy clearing of blockages
when they occur.
Process block valves (at the intersection of

two process lines) should be minimum X X X
distance.
Minimum bends. X X X
Pump suction/discharge piping distances X X X

should be minimized.
Piping system should be designed to avoid low X X X

points or traps.
Single gradual sweeping pipe bend should be X X X

considered instead of using two bends.
RA-1-020-
2 11/28
Notes A B C D E F G
Slurry piping should be placed in the lowest

tier of a pipe rack to provide easy access for X X X
maintenance.
The main process flow shall flow through the X X X

run of a tee.
In-line process flow meters shall be of full-port

or non-intrusive design. Flow meters should be
installed in straight sections of piping X X X
according to manufacturer’s
recommendations.
In-line process densitometers shall be of the

full-port design and shall be installed in a X X X
vertical, (flow up) section of piping.
Pressure relief devices shall be located on top

of the process line and shall be located as X X X
close to the process line as possible.
P&ID guidance regarding instrument locations

for control of the slurry system shall be X X X
adhered to.
Check valves shall be provided to avoid X X X

backflow at process/utility tie-in points.
For erosive slurry services basalt fittings are

specified - see P&ID’s for locations. Where X X X
basalt lined fittings are used the i/d of the lined
and unlined pipes must match.
45-degree laterals should be considered at the

1st Stage Slurry Feed Pumps’ and 2nd Stage X
Slurry Feed Pumps’ suction headers.
Additional wall thickness requirements for pipe

bends:
Wall thickness to be increased to allow for X X X X
thinning during bend forming.
Pipe bends shall be taper-bored to suit
mating pipe.
The minimum pipe schedule shall be schedule X

80S.
Eccentric reducers on pump suction lines to be X

installed top flat.
Design pressure of slurry piping to allow for X

design pressure of flushing water.
Where nozzles are necessary, adequate X X

minimum “clean gas” purges should be
RA-1-020-
2 12/28
Notes A B C D E F G
provided as required to keep the material

being handled from packing into nozzles or
instrumentation sensing lines.
The inside diameter of the abrasion-resistant

lining should match the inside diameter of X X
adjoining un-lined pipe.
Traps or dead legs in the piping system should X X

be avoided.
Special adapter flanges may be required to

transition between straight piping runs and
bends, and to match adjoining piping systems, X X
according to bend lining manufacturer’s
recommendations.
Custom manufactured pipe and fittings

fabricated using a carbon steel shell with an X
abrasive-resistant lining of fused cast basalt.
Special design conditions for erosive

twophase flow:
Erosion resistant piping materials. X X X X

Minimize flow disturbances.
Minimize number of bends.
Special “Y” connections and 45-degree bends

should be used in some locations to merge
two parallel lines into one. 45-degree lateral X
branches instead of tees should be used in
some locations. valve-to-valve connections
shall be fitting-to-fitting.
Piping shall be designed for proper X

gravitational flow.
Other process lines connecting with this

process piping system should enter on top of
the process line. Flush connections should X
enter on top of the process line. Laterals may be
used for these connections.
Instrument connections should be on the top

of the process line. Drain connections should
be located on the bottom of the process line. X X
Isolation valves for flush and drain connections
should be piped fitting-to-fitting to line to be
flushed.
RA-1-020-
2 13/28
Notes A B C D E F G
Piping system shall have no pockets and shall

slope gradually downward in the direction of
the process flow. Fused cast basalt-lined
bends shall be used for all pipe bends located
upstream of the last automatic block valve in
the char return line from the Char Filter X
Ejectors to the Gasifier Reactor. High alumina
(90% alumina oxide) ceramic-lined bends shall
be used for all pipe bends located downstream
of the last automatic block valve located in the
char return line from the Char Filter Ejectors to
the Gasifier Reactor.
Nozzles such as sample, pressure tap, and

purge nozzles that connect to the piping
system should be installed on top of the
process line to avoid significant particle build- X X
up in the nozzles. This situation, when water is
present during plant down time, can lead to
significant localized corrosion.
The run lengths of this piping system should be X

minimized.
There should be no abrupt changes in flow X

direction.
Piping should slope downward in certain X

locations as noted on the P&IDs.
This piping system should be streamlined as

much as possible. Traps in this piping system X
should be avoided.
Slag sample points should come off of the side X

of the line.
Flush line flange face projections from the

process piping should be held to a minimum X
distance.
Adequate flush and drain connections should

be added to ensure no dead legs of slurry
stagnant in the pipe. Flush connections should
be located as close to the upstream process X
block valve as possible, and drain connections
as close to the downstream equipment as
possible.
Flow measurement instrumentation should be X

of the non-intrusive type.
RA-1-020-
2 14/28
4.9.3 Low Pressure Vent Gas
Layout of piping system should follow the general requirements specified as follows.
All branch tie points should enter into the top of the main header.
Branch runs should be laid out to minimize pockets in the line and sloped from the
high point at the vent source.
4.9.4 Sour Service
The following line services of process piping are sour services according to the criteria of
NACE MR0175. The vapor phase streams that are listed can develop a separate
water/moisture phase containing hydrogen sulfide due to condensation from the vapor
phase via dead legs, cold spots, etc.
HPW - High Pressure Process Water
P - Process
PSOG - Sour Gas
PW - Process Water
RW - Recycle Water
SG - Syngas
SPW - Sour Process Water
TV - Tank Vent
Specific piping material requirements for sour service are;
Material selection to be in compliance with licensor B standard LS 129-37 and LS

129-38 SG1.
Material shall be stainless steel A312 seamless or A358 welded grade 304/304L, or
carbon steel A106 grade B seamless pipe or A333 grade 6 seamless and welded
pipe.
Socket weld and threaded joints are not permitted.
Dissimilar joints are not permitted.
Valves in class 150 services should be class 300 up to and including DN50.
Carbon steel pipe welds to be PWHT.

RA-1-020-
2 15/28
4.9.5 Requirements for Wet & Gaseous Oxygen
These piping systems are used for high purity gaseous oxygen service that contacts
other process fluids containing moisture.
Precautions to ensure cleanliness of the piping system for oxygen service should be
used for supply and installation of piping components, and during maintenance.
Layout of piping system shall follow the practices specified in CGA Practice 4.4. The
following requirements should also be followed.
Piping system should not be located in an area that will potentially expose it to an
extraordinary amount of hydrocarbons.
Do not route this system under or near lube oil systems.
The run lengths of this piping system should be minimized.
Instrument connections should be minimized. Instrument connectors should use

sealant compatible with oxygen service.
See Doc. No.RA-1-020-EP241-11004 ‘Piping Job Instruction - Para. 10.5’.
4.10 Piping Adjacent to Equipment
4.10.1 General
Piping and pipe supporting structures shall be designed so that access is provided for
maintenance or removal of valves, in-line instruments, tube bundles and shell/channel
covers (e.g. cranes and trucks) and for operational reasons (e.g. filter cleaning).
Removal or replacement of equipment shall be possible with a minimum dismantling of

piping.
Removable pipe spools may be required.
Small pieces of equipment and ancillaries which need regular inspection or maintenance
should be installed on elevated plinths in order to improve access.
4.10.2 Drain and Vent Provisions
All equipment shall have a valved drain and a valved vent provided;
Equipment and piping shall have a minimum size DN20 drain or vent connection for
Process and Utility lines.
Equipment drains and vents are not required if the equipment can be adequately
drained or vented via connected piping.
4.10.3 Pumps
RA-1-020-
2 16/28
All pump suction lines shall be provided with temporary start-up strainers unless
permanent strainers are specified on the P&ID. A block valve shall be installed upstream
of the strainer in the suction pipe of each pump. The piping components to the suction
nozzle of the pump shall have the same rating as the discharge piping in order to
accommodate overpressure due to backflow from the discharge side. The discharge
pipe shall also have a block valve. A check valve shall be installed unless there is no
possibility of backflow or pressure surge under any conditions. The liquid volume
between the check valve and the pump discharge block valve shall be as small as
practical.
Suction piping shall be as short and as direct as possible, avoiding high spots where
pockets of gas or air could accumulate. Only eccentric reducers (top flat) may be used for
pipe diameter changes in horizontal pipes. In vertical pipes, eccentric or concentric
reducers may be used.
Valve handwheels shall be oriented whenever possible to be contained within the

perimeter of the pump frame. They shall be readily operable from grade.
Piping shall be designed in a manner such that no undue stress is put on pump nozzles
due to the effects of thermal expansion or weight of pipe. Clearance must be provided
for removal of pump and/or driver and on end suction pumps for removal of suction
cover and pump impeller while the suction and discharge valves are in place.
The length of straight pipe from the last elbow to the suction nozzle (which shall not
include any reducer, strainer or valve) shall be sufficient to ensure minimum turbulence at
the pump suction nozzle.
See Doc. No.RA-1-020-EP400-10004 ‘Piping Job Notes’ Job Note Sheet 07.
4.10.4 Compressors
To prevent fatigue failure of compressor piping, the effect of vibrations and pressure
surge shall be considered.
Inter-stage and discharge piping shall be sufficiently flexible to allow expansion due to the
heat of compression.
Butt-welding components shall be lined up accurately and weld roots shall be ground
smooth wherever possible.
Block valves shall be installed in the suction and discharge pipes, except for
atmospheric air compressors, which shall have block valves in the discharge pipes only.
RA-1-020-
2 17/28
In each compressor suction pipe, a temporary start-up suction strainer shall be installed
downstream of the block valve of the compressor and as close as possible to the
compressor suction nozzle.
The suction pipe between a knock-out drum and the compressor shall be as short as
practicable, should have no pockets and should slope down towards the knock-out drum.
Compressors in hydrocarbon or very toxic service shall have purge facilities. Spading
capability shall be provided by spectacle blinds, removable spool pieces or elbows.
Any auxiliary piping, associated with equipment, shall be neatly routed along base-plates
and shall not extend across operating areas. Piping shall not obstruct inspection covers,
bearing caps, upper halves of casings or any other items which require access for
operation or maintenance.
In order to avoid a fire hazard, lubricating oil, control oil and seal oil pipes shall not be
routed in the vicinity of hot process or hot utility pipes.
Cooling water pipes to pumps and compressors shall not be less than DN20. Pipes
DN25 or less shall have the take-off connection from the top of the water main pipe in
order to prevent plugging during operation.
4.10.5 Steam Turbines
Piping shall be designed to permit steam-blowing up to the inlet and outlet flanges of the
turbine before start-up.
Steam vents shall be routed to a safe location and shall not be combined with any
lubricating oil, seal oil or process vent.
4.10.6 Heat Exchangers
Exchangers shall be grouped together wherever possible.
Sufficient space shall be allowed for tube bundle removal.
Sufficient space shall be kept between adjacent heat exchanger inlet and outlet valve
manifolds.
Shell and channel box piping shall be provided with vent and drain connections unless it
can be vented and drained via other equipment. Drain and vent nozzles on heat
exchangers shall have a valve and a blind flange.
To allow removal of covers, heads, channels, bundles and shells, pipes shall not be
supported on heat exchanger shells or heads.
4.10.7 Pressure Vessels

RA-1-020-
2 18/28
Vertical pipes branching from columns and other vertical vessels shall have a resting
support near the nozzle and shall be guided at regular intervals to protect the pipe
against vibrations, wind load and/or buckling. Pipe supports on pressure vessels shall be
bolted to cleats welded to the vessel. Cleats shall be designed and form an integral part
of the pressure vessel. Cleats and the connected pipe supports and/or supporting steel
shall be designed so that there will be no ingress of water under the insulation.
Generally piping shall be grouped together for common supports.
Where practical, pressure vessels which are grouped together shall have platforms and
interconnecting walkways at the same elevation. Pressure vessels shall have a drain,
either on the bottom outlet pipe or at the lowest point of the vessel. The drain valve shall be
outside the skirt. The size of the drain shall be at least DN50.
4.11 Utility Piping
4.11.1 Cooling Water
Cooling water pipes should have block valves at the plot limit so that they can be
isolated for maintenance while the cooling water system remains in operation.
Main distribution pipes shall have facilities at the lowest points to permit complete
draining within 6 hours.
Venting facilities shall be provided to relieve air pockets.
4.11.2 Water for Other Purposes
Water pipes which are exposed to freezing, even for a short duration, shall be protected.
Hose stations shall have a valve, a connection of the quick-coupling type, a 15 m water
hose and a hose rack.
4.11.3 Steam
Piping in steam service shall be arranged so that condensate accumulation is avoided.
Stagnant and reverse-flow conditions shall be avoided in steam distribution systems.
Generally, pipes to steam users shall branch off from the top of the steam supply pipe in
order to prevent condensate.
Steam pipes shall have a block valve at the boundary of the process unit. Flanges shall be
provided at these locations to allow for spading to isolate the steam systems during
maintenance of the unit.
All steam pipes shall have drain facilities at the low points and at the end of sub-headers to
remove condensate (e.g. during commissioning).
RA-1-020-
2 19/28
Steam traps shall be installed at low points or at natural drainage points, e.g. in front of
risers, expansion loops, changes of direction, (closed) valves and regulators. Steam
traps shall be as near as possible to the condensate outlet of the equipment or piping to be
drained, unless a cooling leg is required.
In saturated steam service, steam traps shall be fitted to drain-pockets.
Steam traps shall be positioned so that they are easy to maintain and replace. Open
steam trap discharges shall be avoided but if used they shall be located away from
doors, windows and air intakes.
For steam services, valves DN150 and larger in ASME rating class 600 and higher shall
have a bypass valve for preheating and pressure-balancing.
4.11.4 Utility Hose Stations
Utility stations for steam, air, water & inert gas shall be provided where required. Utility
stations should be located so that all points of use within the process area can be
reached by 15 m long hoses. Each type of utility medium shall be provided with a
dedicated type of hose connection to prevent contamination and inadvertent connection to
the wrong utility medium.
Utility pipes to the manifolds shall branch off from supply headers which cannot contain
contamination, e.g. due to leaking heat exchangers, etc.
4.11.5 Tank Farm Piping
Within bunded areas the number of pipes shall be minimised and they shall be routed in
the shortest practicable way from the tank to the bundwall. Where practical, the pipes
shall be grouped together.
Piping shall be connected and supported after hydrostatic testing of the tank. Piping in
tank farms shall be supported by concrete sleepers or steel frames. Access to manholes,
mixing nozzles, drains and other facilities on the tanks shall not be impeded by piping.
Manifolds shall be located outside the bundwall in a concrete paved curbed area. Tank
nozzles, including product drains and water draw-off connections, shall have block
valves. Pipes may only be routed through bund walls if they cannot be passed over such
walls (e.g. suction pipes).
4.12 Instrument Piping
4.12.1 Instrument Process Connections

RA-1-020-
2 20/28
Connections to piping for instruments shall be developed & included within the piping
classes. The design and material selection of in-line instruments and control valves shall
satisfy the pressure and temperature rating of the relevant piping class.
Generally, instrument connection points shall be as short as possible. Long connections, if

unavoidable, and/or connections to vibrating pipes shall be properly braced.
To ensure clear visual access for operators, Instruments shall not be placed behind
pipes or other obstacles. Instruments shall be accessible from ground level, platforms or
ladders for operation & maintenance.
Level gauges shall be installed on stand pipes if two or more instruments are installed.
Stand pipes shall satisfy the specifications of the relevant piping class. The minimum
diameter of a stand pipe shall be DN80 and the equipment connections shall be DN50.
Loads on equipment nozzles, caused by the weight and/or thermal expansion of stand
pipes with level gauges or by magnetic type level gauges, shall be checked.
Instrument valves shall be 15mm up to and including class 600 flanges and 20mm for
flanges class 900 and above.
Double block valves for instruments are required for class 900 and higher services.
4.12.2 Connections for Sampling
Dedicated connections shall be provided for sample collection.
The sampling point shall be positioned so that the valves are easy to operate and taking
the sample will not impair the safety of personnel or plant, or cause environmental
impact.
Samples should be taken from a vertical pipe where possible; where this is not possible:
For gaseous products in horizontal pipes, sample take-off connections shall be
installed at the top of the pipe.
For liquid products in horizontal pipes, sample take-off connections shall be installed
at the side of the pipe.
Sample take-off connections shall not be located at dead ends of piping.
Sample take-off connections shall be easily accessible and should be at ground level.
Sample pipes shall be as short as possible.

RA-1-020-
2 21/28
As far as practicable, sample connections shall be grouped together and provided each
with a sample cabinet which can be connected to one common drain facility. Wherever
possible, Drain facilities shall be connected to a sample recovery system.
Precautions shall be taken to avoid freezing or plugging of the sample pipe. Specific
sample arrangements shall be as indicated on the project P&ID as specified by drawing
RA1-0-0006 ‘P&ID legend sheet - Sample connections’.
4.12.3 Positive Isolation
Spectacle blinds, spades, spacers and blind flanges shall be formed from the same
material as the mating flanges & have the same rating class as the piping.
Piping shall be designed, supported and installed so that the flanges do not move when
the bolting is removed for spading purposes. The piping shall be sufficiently flexible to be
able to install the required isolation fittings (spades, blind plates etc.) and there shall be
sufficient space to turn spectacle blinds, where provided.
Spectacle blinds and spades shall be located so that they are accessible from ground
level or from platforms or walkways. The need for scaffolding shall be minimised or
eliminated.
A removable spool and blind flanges shall be used in the following situations:
Where the nozzle is used for entry into the equipment;
Where the nozzle is used for hoisting purposes (e.g. top nozzles on columns);
Where the nozzle (e.g. the head of a heat exchanger) is used to remove internals
(e.g. the tube bundle);
Where the nozzle is used for loading/unloading of solids (e.g. catalyst).
Size limits for selection of spectacle blinds or spacer rings/blinds.

RA-1-020-
2 22/28
Rating Spectacle Blind Spacer Ring/Blind
150# DN350 & smaller DN400 & larger
5.0 MATERIALS
5.1 General
Reference shall be made to the individual Licensor packages, material selection diagrams &
various P&ID legend sheets for guidance on material selection applicable to each process unit’s
materials of construction & pipe class designations. The following shall be read in conjunction
with the piping line class Attachment #1.
5.2 Materials of Construction
All material shall be unused, of premium quality, free from segregation, cracks, laminations and
surface flaws.
The following restrictions on the carbon content of metallic materials shall apply:
Carbon steels:
Pipe & plate: maximum 0.23%
Forgings & castings: maximum 0.25%
Chromium molybdenum steels (with less than 2% chromium):
Chromium molybdenum steels (with 2% or above chromium):
Care shall be taken to avoid any possibility of contaminating austenitic stainless steel, duplex
stainless steel, nickel alloy or 9% nickel steel components with zinc.
RA-1-020-
2 23/28
5.2.1 Carbon Steel
Carbon steel pipe classes where the corrosion allowance is less than 3mm are primarily
applied to boiler feed water, steam, non-aggressive process lines and utilities. Where
corrosion allowance is greater than 3mm, several process services are referenced. In
addition, jacketed carbon steel pipe is required for transportation of liquid sulphur.
The following grades of carbon steel are used;
API 5L grade B, PSL (Product Specification Level) 1.
The following grades of carbon steel are used where specified by licensor B pipe
specification index document no. RA-1-020-AA242-10001;
ASTM A106 Grade B, Seamless.
ASTM A333 Grade 6, Seamless.
ASTM A671-CC65, Electric fusion welded.
ASTM A333 Grade 6 and ASTM 671-CC65 are impact tested where required;
ASTM A53 Grade B seamless is used for galvanised carbon steel pipe.
Spiral welded pipe shall not be used.
Additional requirements for wet H2S & hydrogen service shall be applied where
necessary.
5.2.2 Carbon Steel (Lined)
Carbon steel (lined) pipe classes are primarily applied to high pressure slag water and
slag. Where corrosion allowance is greater than 3mm, several process services are
referenced. In addition, lining is required for pipe classes associated with recycled char,
as follows;
Fused cast basalt-lined bends shall be used for all pipe bends located upstream of the
last automatic block valve in the char return line from the char filter ejectors to the
gasifier reactor.
High alumina (90% alumina oxide) ceramic-lined bends shall be used for all pipe bends
located downstream of the last automatic block valve located in the char return line from
the char filter ejectors to the gasifier reactor.
PTFE lined carbon steel and ductile iron are used where the process media is
hydrochloric acid.
5.2.3 Chromium and Molybdenum

RA-1-020-
2 24/28
Cr-Mo steels are selected for high strength at high temperature and/or for resistance to
hot hydrogen attack.
Cr-Mo steels have also been defined for handling of aggressive fluids. Grades of 1.25% &
2.25% chrome have been specified.
Additionally Cr-Mo piping has been specified as base material for N10276 clad piping in
syngas & scrubber circulation water service.
5.2.4 Stainless Steel
For several process media at temperatures up to 425 °C, dual certified ASTM A312-
TP304/304L, or ASTM A358-304/304L have been specified in line with licensor
requirements.
For wet oxygen, ASTM A312-TP310 is specified.
For sour gas, TP-316 is proposed.
For more aggressive media duplex S.S. A790/S32750 is specified.
Stainless steel pipe will be Seamless up to and including DN300, and will be DSAW
(Double submerged arc welded) for sizes above DN300, unless specified otherwise by
licensor B pipe specification index document no. RA-1-020-AA242-10001.
5.2.5 Nickel Alloy
Nickel-iron-chromium alloys will be required for high temperature and aggressive fluids.
Grades of nickel alloys specified include Incoloy 825 type UNS N08825 or equivalent,
Hastelloy B type UNS N10665 or equivalent and Inconel 625 type UNS N06625 or
equivalent.
For gaseous oxygen, Monel 400, ASTM B165 N04400 annealed and ASTM B725
N04400 annealed Cat 2 have been specified.
Monel 400 pipe will be Seamless up to and including DN300, and will be DSAW (Double
submerged arc welded) for sizes above DN300.
5.2.6 Galvanised Piping
Galvanised carbon steel piping in sizes DN15 up to DN80 DN40 should be constructed
from pre-galvanised screwed pipe and fittings.
Galvanised piping ≥DN100 DN50 should be made as pre-fabricated pipe spools or as

field welding and zinc painting touch-up at unpainted area within reachable extent by
hand.
RA-1-020-
2 25/28
These spools shall be flanged and shall be restricted to shapes that permit hot dip
galvanising after fabrication.
Field welds may be applied only on galvanised systems that will be full of liquid in
service.
5.2.7 Plastic Piping
GRP (Glass reinforced polymer) API 15LR, ASTM D2996 Filament wound RTR pipe has
been specified for seawater media.
CPVC (Chlorinated polyvinyl chloride) ASTM F441 CPVC 4120 plastic pipe has been
specified for hypochlorite dosing media.
HDPE (High density polyethylene) pipe is to be used for certain media to be specified in
detail design engineering.
5.2.8 Aluminized Piping
Aluminized carbon steel will be required for sea waterU/G Cooling water, U/G Fire Water.
Grades of aluminized piping specified in JIS H8642 or equivalent aluminized piping
should be made as pre-fabricated pipe spools or as field welding and special painting
touch up which reachable extent by hand.
These spools shall be flanged and shall be restricted to shapes that permit aluminizing
after fabrication.
5.3 Piping Components
5.3.1 Fittings
Fittings shall be in accordance with ASME B16.5, ASME B16.9, ASME B16.24 or ASME
B16.47, as applicable for the type of fitting.
All butt-welding component thicknesses shall match the pipe thickness.
The following types of fittings shall not be used, unless specified by the licensors:
Reducing outlet crosses
Straight crosses
Reducing elbows
Short radius butt weld elbows,
Street elbows
Reducing on-the-run tees
Short nipples
RA-1-020-
2 26/28
Bushings
Bar stock machined reducers
Bar stock machined fittings
Reducing butt weld fittings shall have ends specified to the same schedule or weight as
the mating pipe.
5.3.2 Threaded Joints
Threaded joints shall not be used in process piping.
Threaded nipples shall not be used.
Threaded joints are only permitted at the outlet of vent and drain valves, hydrostatic
connections, outlet instrument take-off valves and to match equipment.
Seal welding of threaded connections is only allowed at Hydrostatic Vents.
Where seal welds are required, no sealant or thread compounds shall be used and all
cutting fluids shall be removed prior to the joint being made.
5.3.3 Branch Fittings
Economic aspects and service conditions shall be considered in the selection of the
reinforcing method.
Butt-welding tee fittings shall be used in severe cyclic service.
Branch connections shall not be made on fittings.
5.3.4 Flanges
Flanges shall be raised-face in accordance with ASME B16.5.
Flanges over DN600 shall be in accordance with ASME B16.47 series A. The use of
other types of flanges is subject to approval.
The flange facing finish shall be in accordance with ASME B16.5 or ASME B16.47, as
applicable.
Weld neck flanges shall generally be used except where slip-on flanges are allowed
within the material specification.
Slip-on flanges shall not be attached directly to fittings such as tees, elbows or reducers.
Lap joint C.S. (A-105) Flanges shall be specified for higher alloys lines DN50 & above.
Flange bolt holes shall straddle the centre lines.

RA-1-020-
2 27/28
If a flat face flange is required (e.g. GRE piping in ASME rating class 150) the counter
flange shall also have a flat face in accordance with ASME B16.5. Flat face flanges shall be
provided with full-face gaskets.
For bolt material and temperature limitations see 4.2.8 below.
Bolted joints not classified as flanges, e.g. V-clamps, groove joints, may be used only with
approval.
5.3.5 Gaskets
Compressed Asbestos Fibre (CAF) and Man Made Mineral Fibres (MMMF) shall not be
used.
Flat sheet gaskets - graphite tanged insert gaskets shall be used instead of Compressed
Asbestos Fibre (CAF) gaskets.
For uniformity, and to prevent mistakes, all nozzles on a piece of equipment should be
provided with the same type of gasket. The most stringent design condition shall
determine the required gasket.
If graphite-based materials cannot be used, e.g. for contamination reasons, PTFE-based

materials shall be applied up to a maximum temperature of 200 °C.
5.3.6 Spiral Wound Gaskets
Graphite-filled gaskets shall be used instead of asbestos-filled.
Spiral wound gaskets, with inner rings to provide additional strength, shall be used in the
following cases:
class 600;
diameters larger than DN600, regardless of service class and filler material;
all PTFE-filled spiral wound gaskets, regardless of service class and diameter;
if protection of the filler material against corrosion is required or to prevent the filler
material from reaching too high a temperature;
if it is necessary for the annular space to be filled in order to reduce the possibility of
turbulent flow, or to prevent accumulation of solids, or to prevent erosion of the
flange faces.
Spiral wound/Monel 400 gaskets may be used up to a design temperature of 400 °C.
Spiral wound/Inconel 600/graphite gaskets may be used up to a design temperature of

650 °C.
RA-1-020-
2 28/28
Spiral wound gaskets shall have a colour code in accordance with the relevant
standards.
5.3.7 Ring Joint Gaskets
Oval ring gaskets shall be used in the following cases:
Class 900 and class 1500;
If necessary in high temperature service;
If it is necessary for the annular space to be filled in order to reduce the possibility of
turbulent flow, or to prevent accumulation of solids, or to prevent erosion of the
flange face
5.3.8 Selection and Installation of Bolting Materials
The design temperatures for the listed bolting material combinations in relation to the
applied piping material shall be as follows:
Nut material Allowable design Diameter

Bolt material
Piping material [ASTM temperature range
[ASTM designation]
designation] range [°C] [inch]
Carbon steel
Low alloy steel
Stainless steel A193-B7 A194-2H -40 to 400 ½ - 4
Duplex stainless steel
Non-ferrous metal
Non-metal
Carbon steel (high sour) A193-B7M A194-2HM -48 to 400 ½ - 4
Carbon steel LT
Stainless steel
Duplex stainless steel A320-L7 A194-4 -101 to 343 ½ - 4
Super duplex stainless steel
Non-ferrous metal
Carbon steel LT (high sour) A320-L7M A194-7M -73 to 343 ½ - 4
Low alloy steel A193-B16 A194-4 -29 to 480 ½ - 4
Low alloy steel 20CrMoVTiB4-10 20CrMoVTiB4-10 -20 to 550 ½ - 4
Stainless steel A453-660 class C A453-660 class C -29 to 538 ½ - 3½
Stainless steel A193-B8 class 2 A194-8 -200 to 425 ½ - 1½

Duplex stainless steel A193-B8M2 class 2B A194-8 -200 to 425 1½ - 3
TECHNICAL SPECIFICATION Doc. No. Rev. No. Page
FOR PIPING MATERIALS RA-1-020-

2 1/327
EP242-11001
(ATTACHMENT #1)
ATTACHMENT #1
Piping Line Classes and Summary


2 2/327
EP242-11001
(ATTACHMENT #1)
1.0 INTRODUCTION
The piping classes contained in this document consist of a collection of standardized piping
components that are compatible and are suitable for a defined service at stated pressure and
temperature limits. All components applied in these piping classes are covered by material
standards and design codes.
2.0 PURPOSE
This document provides the technical requirements for selection of piping and components
according to the materials of construction, design pressure and temperatures, as specified by the
licensors and process engineering groups for the POSCO SNG Project.
3.0 SELECTION OF BASE MATERIALS
The following basic information has been provided by the gasification licensor piping material
guidelines document.
Basic materials of construction, design code and corrosion allowance.
Design pressure and temperature
Line size criteria.
ASME pressure class.
Valve and speciality items.
Design notes.
Metallic piping classes have been designed in accordance with ASME B31.3.
4.0 REFERENCE
4.1 CODES AND STANDARDS
4.1.1 ASME (American Society of Mechanical Engineers) Standards

B1.1 Unified Inch Screw Threads
B1.20.1 Pipe Threads, General Purpose (Inch)
B16.1 Cast Iron Pipe Flanges and Flanged Fittings, (Class 25, 125 and 250)
B16.5 Pipe Flanges and Flanged Fittings


2 3/327
EP242-11001
(ATTACHMENT #1)
B16.9 Factory-Made Wrought Steel Buttwelding Fitting
B16.10 Face-to-Face and End-to-End Dimensions of Valves
B16.11 Forged Steel Fittings, Socket-Welding and Threaded
B16.20 Metallic Gaskets for Pipe Flanges, Ring-Joint, Spiral-Wound, and Jacketed
B16.21 Nonmetallic Flat Gaskets for Pipe Flanges
B16.25 Buttwelding Ends
B16.28 Wrought Steel Buttwelding Short Radius Elbows and Returns
B16.34 Valves-Flanged, Threaded, and Welding End
B16.47 Large Diameter Steel Flanges
B18.2.1 Square and Hex Bolts and Screws (Inch Series)
B18.2.2 Square and Hex Nuts (Inch Series)
B31.1 Power Piping
B31.3 Process Piping
B36.10M Welded and Seamless Wrought Steel Pipe
B36.19M Stainless Steel Pipe
4.1.2 API (American Petroleum Institute) Standards

Std. 594 Check Valves: Wafer, Wafer-Lug and Double Flanged Type
Std. 600 Steel Gate Valves Flanged and Buttwelding Ends
Std. 602 Compact Steel Gate Valves-Flanged, Threaded, Welding, and Extended-Body
Ends
Std. 608 Metal Ball Valves-Flanged and Butt-Welding Ends
Std. 609 Butterfly Valves: Double Flanged, Lug-Type and Wafer-Type
Spec. 5L Specification for Line Pipe
4.1.3 MSS (Manufacturers Standardization Society of the Valve and Fittings Industry)
SP-79 Socket welding reducer inserts
SP-83 Class 3000 steel pipe unions socket welding and threaded.
SP-95 Swaged nipples and bull plugs.
SP-97 Integrally reinforced forged branch outlet fittings, socket welding, threaded and

2 4/327
EP242-11001
(ATTACHMENT #1)
buttwelding ends.
4.1.4 ASTM (American Society for Testing and Materials) Standards

4.2 FEED DOCUMENTS
Valve Specification Document No.RA-1-020-EP242-10003
Ball Valve Data Sheets Document No.RA-1-020-EP400-10006
Gate Valve Data Sheets Document No.RA-1-020-EP400-10008
Check Valve Data Sheets Document No.RA-1-020-EP400-10009
Globe Valve Data Sheets Document No.RA-1-020-EP400-10010
Butterfly Valve Data Sheets Document No.RA-1-020-EP400-10011
Plug Valve Data Sheets Document No.RA-1-020-EP400-10012
Knife Gate Valve Data Sheets Document No.RA-1-020-EP400-10013
5.0 CONFLICT
5.1 When there is a conflict between the requirements of Other Project Specification, e.g.
Project Design Basis or Special Design Requirement, and this PIPING MATERIAL
SPECIFICATION, the requirements of the Other Project Specification shall take precedence.
5.2 When there is a conflict between the requirements of the applicable standards and this
specification, the requirements herein shall take precedence.
6.0 DESIGNATION OF PROCESS PIPING CODES
6.1 Piping is designated by ASME pressure class.
01 for 150 lb
03 for 300 lb
06 for 600 lb
09 for 900 lb
15 for 1500 lb
6.2 Unique process piping material code.
Code Description

2 5/327
EP242-11001
(ATTACHMENT #1)
A Carbon steel, low pressure general water and gas service
B Duplex stainless steel, 2507, high chloride water
C Stainless steel, dual certified 304/304L, high pressure slurry service
D Impact tested low temperature carbon steel
E 1.25% Cr 0.5% Mo steel, high temperature
F Carbon steel, high pressure general water and gas service
G Killed Carbon steel, corrosive service (PWHT)
H 2.25% Cr 1.0% Mo steel
J Stainless steel, 310, wet oxygen service
K Stainless steel, dual certified 304/304L, low pressure slurry service
L Stainless steel, 321
M Stainless steel, dual certified 304/304L, high pressure char-laden syngas
service
N Stainless steel, dual certified 304/304L, high pressure recycle syngas
P Carbon steel, lined, medium pressure slag slurry service
Q Stainless steel, medium pressure slag slurry service
R Stainless steel, low pressure corrosive water service
S Stainless steel, dual certified 316/316L
T Carbon steel jacketed
U Stainless steel, dual certified 304/304L , Cryogenic and low pressure vent gas
service
V Stainless steel, dual certified 304/304L, high pressure syngas service
W Carbon steel, high pressure intermittent slurry service
Y Duplex stainless steel, 2205
Z 904L Stainless steel, N08904
6.3 Corrosion allowance.
0 for zero corrosion
1 for 1.6mm

2 6/327
EP242-11001
(ATTACHMENT #1)
2 for 3.2mm
4 for 6.4mm
Example code:
01A1 is 150lb Carbon Steel, low pressure general water and gas service with 1.6mm
corrosion allowance.
7.0 DESIGNATION OF UTILITY PIPING CODES
7.1 Piping is designated by ASME pressure class.
01 for 150 lb
03 for 300 lb
06 for 600 lb
09 for 900 lb
15 for 1500 lb
7.2 Unique utility piping material code.
Code Description
CS Carbon steel
CH PTFE Lined carbon steel
FG GRP
GA Galvanised carbon steel
HD High density polyethylene
PV CPVC
SA 304/304L Stainless steel
SS Generic stainless steel
NM Alloy 400 (Monel), UNS N04400
7.3 Corrosion allowance.
0 for zero corrosion
1 for 1.6mm
2 for 3.2mm

2 7/327
EP242-11001
(ATTACHMENT #1)
Example code:
01CS1 is 150lb Carbon Steel with 1.6mm corrosion allowance.
8.0 GEAR OPERATORS
Bevel or worm gear types shall be complete with hand wheels and position indicators. The
operators shall be weatherproof, totally enclosed and packed with suitable lubricant. Where the
units are not "sealed for life" they shall be suitable for re-packing with grease whilst the valve is
installed in line. Gear operators shall be mounted in such a way that they can be easily unbolted
from the valve body and subsequently be repositioned in 90° increments.
Gear operators shall be of such a design that the valve can be fully opened and closed with a
correct flow passage. For ball & butterfly type valves the gear operator design shall prevent the
ball or blade turning past the 90° fully open or closed position.
Bevel gearing is preferred for gate valves and spur gearing for globe valves.
150# 300# 600# 900# 1500#
GATE 350&over 300&over 300&over 200&over 200&over
GLOBE 250&over 250&over 150&over 150&over 150&over
BALL 200&over 200&over 150&over 100&over 100&over
PLUG 200&over 200&over 150&over 100&over 100&over
BUTTERFLY 200&over 200&over 200&over 200&over 200&over
9.0 DEFINITIONS OF ABBREVIATIONS USED IN PIPING CLASSES.
API American Petroleum Institute.
ASME The American Society of Mechanical Engineers
BBE Beveled Both Ends
BE Beveled End
BW Butt Welded
C.PTFE Coated Teflon (TFE)
CR Chrome
CR PL.SS Cr Carbide Coated Stainless Steel


2 8/327
EP242-11001
(ATTACHMENT #1)
CR OR NI PL.CS Cr or Ni Plated Carbon Steel
CS Carbon Steel
DI Ductile Iron
DSAW Double Submerged Arc Welded
FB Floating Ball
FF Full Faced
FP Full Port
GO Gear Operated
HF Hard Faced
IS Integral Seat
LJ Lap Joint
LR Long Radius
MDMT Minimum Design Metal Temperature
MSS Manufacturers Standardization Society
NACE National Association Corrosion Engineers
NB Nominal Bore
OD Outside Diameter
PBE Plain Both Ends
PE Plain End
PFA Perfluoroalkoxy
P&ID Piping and Instrumentation Diagram
PLT Plate
POE Plain One End
PTFE Polytetrafluoroethylene
PTFE.L Teflon (TFE) Lined
PWHT Post Weld Heat Treatment
RAT Rating
RED Reducer

2 9/327
EP242-11001
(ATTACHMENT #1)
RF Raised Face
RP Reduced Port
RPTFE Reinforced Tetrafluoroethylene
RS Rising Stem
RTFE Reinforced Tetrafluoroethylene
RTJ Ring Joint
SCH Schedule
S&D Seat & Disc Hard Facing
SMLS Seamless
SS Stainless Steel
ST Stainless Trim
STD Standard Weight
SW Socket Welded
TBE Threaded Both Ends
THRD Threaded
TM Trunnion Mounted Ball
TOE Threaded One End
WC-INCONEL Tungsten Carbide Coated Inconel
WN Weld Neck
XS Extra Strong
XXS Double Extra Strong

Doc. No. Rev. No.
TECHNICAL SPECIFICATION Page

2 10/334
EP242-11001
(ATTACHMENT #1)
Line Class Corr. Flange
No. Service Primary Material PWHT / NACE Design Codition
No. Allow. Class
1 01A1 ATMOSPHERIC VENT(AV) 1.6 mm CS Not required Design Temperature
(p. 18) (Licensor A) FLUSH WATER(FLU) (API5L-B-PSL.1) -29 to 425 (C)
SLAG WATER(PW) Design Pressure
LP SLAG WATER(PW) 19.6 to 5.5 (barg)
RECYCLE WATER(RW)
PISTON FLUSH WATER(PFW)
SLURRY(SLU)
TANK VENT(TV)
2 01A1B SLAG WATER(PW) 1.6 mm CS Not required Design Temperature
(p. 22) (Licensor B) CARBON DIOXIDE (LCD, MCD) (API5L-B-PSL.1, -29 to 425 (C)
RECTISOL(RECL, RECR) ASTM A671-CC65-Cl.22) Design Pressure

19.6 to 5.5 (barg)
3 01A2 SYNGAS RAW(SGR) 3.2mm CS Not required Design Temperature
(p. 27) (Licensor B) SYNGAS SWEET(SGS) (API5L-B-PSL.1) -29 to 425 (C)
SOUR GAS(PSOG)(TBC) Design Pressure
SULPHUR VAPOUR(SV) 19.6 to 5.5 (barg)

4 01B0 SOUR GAS(PSOG) 0.0mm 2507 DUPLEX SS NACE applies Design Temperature
(p. 31) (Licensor B) SOUR WATER - SRU(WSA) (ASTM A790-S32750) -29 to 300 (C)
Design Pressure
20.0 to 10.2 (barg)
5 01C0 LP GASEOUS OXYGEN(LGOX) 0.0mm 304/304L Not required Design Temperature
(p. 34) (Licensor A) OXYGEN VENT(PVO) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
19.0 to 5.5 (barg)
6 01CH0 HYDROCHLORIC ACID(PAC2) 0.0mm PTFE LINED CS Not required Design Temperature
(p. 37) (Licensor B) (ASTM A53-B) -29 to 204 (C)
Design Pressure
150# RF
Consult MFR
7 01CS1 - Licensor A 1.6mm CS Not required Design Temperature
(p. 40) (Licensor A) LP FUEL GAS(LFG) (API5L-B-PSL.1, -29 to 425 (C)
(Licensor B) RAW WATER(RAW) ASTM A671-CC65-Cl.22) Design Pressure
NITROGEN VENT(PVN) 19.6 to 5.5 (barg)
- Licensor B
LP NITROGEN(LN)
LP BOILER FEED WATER(LBFW)
WASTER WATER(WW)
8 01CS1U COOLING WATER RETURN(CWR) 1.6mm ALUMINIZED CS Not required Design Temperature
(p. 45) (Licensor A) COOLING WATER SUPPLY(CWS) (ASTM A53-B, -29 to 425 (C)
FIREWATER(under ground)(FW) ASTM A671-CC65-Cl.22) Design Pressure
19.6 to 5.5 (barg)
9 01CS2 ATMOSPHERIC STEAM COND.(AC) 3.2mm CS Not required Design Temperature
(p. 48) (Licensor A) OPEN DRAIN(DRO) (API5L-B-PSL.1, -29 to 425 (C)
(Licensor B) CASOIL/DIESEL(FGO) ASTM A671-CC65-Cl.22) Design Pressure
STEAM VENT(PVS)
BLOWDOWN(BD)
WASTER WATER(WW)
LP COND.(LC)
LP STEAM(LS)
COOLING WATER SUPPLY(CWS)
COOLING WATER RETURN(CWR)
10 01CS2U SOUR CLOSED DRAIN 3.2mm GALVANIZED CS+ Not required Design Temperature
(p. 54) (Licensor A) COLD TAPE WRAPPING -29 to 425 (C)
(Licensor B) (API5L-B-PSL.1, Design Pressure
ASTM A671-CC65-Cl.22) 19.6 to 5.5 (barg)
Doc. No. Rev. No.

2 11/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
11 01CS4 AMMONIA STRIPPING 6.4mm CS PWHT applies Design Temperature
(p. 60) (Licensor B) WASTE WATER(from NH3 Stripper) (ASTM A106-B) -29 to 425 (C)
(WWS) Design Pressure
SOUR GAS(from NH3 Stripper)(PSG) 19.6 to 5.5 (barg)
LP STEAM FOR SULPHUR PIT(LSS)

12 01D1 LOW PRESSURE CARBON 1.6mm IMPACT TESTED CS Not required Design Temperature
(p. 64) (Licensor B) DIOXIDE(LCD) (ASTM A333-6, -46 to 350 (C)
MEDIUM PRESSURE CARBON ASTM A671-CC65-Cl.22) Design Pressure
DIOXIDE(MCD) 18.3 to 8.4 (barg)
(Hydrogen content to be considered
up to 200℃)
13 01D2 VERY TOXIC METHANOL SOLUTION 3.2mm IMPACT TESTED CS PWHT and NACE apply Design Temperature
(p. 68) (Licensor B) (RECT) (ASTM A333-6, -46 to 350 (C)
SOUR GAS(PSOG) ASTM A671-CC65-Cl.22) Design Pressure

VERY TOXIC SYNGAS(SGT) 18.3 to 8.4 (barg)
14 01FG0 HYDROGEN CLORIDE 0.0mm GRP Not applicable Design Temperature
(p. 73) (Licensor B) (ASTM D2996) 0 to 93 (C)
Design Pressure
10.3 (barg)
15 01G1 CAUSTIC SODA(PCA) 1.6mm Killed CS Required Design Temperature
(p. 75) (Licensor B) (ASTM A106-B) on all Butt Welds -29 to 425 (C)
Design Pressure
19.6 to 5.5 (barg)
16 01G2 FLARE(FLR) 3.2mm Killed CS PWTH and NACE apply Design Temperature
(p. 78) (Licensor A) (ASTM A106-B) -29 to 425 (C)
(Licensor B) Design Pressure
19.6 to 5.5 (barg)
17 01G2B RECTISOL SOLUTION RICH(RECR) 3.2mm Killed CS PWTH and NACE apply Design Temperature
(p. 82) (Licensor B) CERY TOXIC SYNGAS(SGT) (ASTM A106-B) -29 to 425 (C)
SOUR GAS(PSOG) Design Pressure
150# RF
CAUSTIC SODA(PCA) 19.6 to 5.5 (barg)
COLD FLARE GASES(FLRC)

18 01GA0 INSTRUMENT AIR(IA) 0.0mm GALVANISED CS Not required Design Temperature
(p. 86) (Licensor A) PLANT AIR(PA) (ASTM A53-B) -15 to 100 (C)
Design Pressure
10.4 (barg)
19 01GB0 FIRE WATER(Above Ground)(FW) 0.0mm GALVANISED CS Not required Design Temperature
(p. 89) (Licensor A) (ASTM A53-B) HOLD
HOLD
20 01K2 SLURRY RETURN(SLU) 3.2mm 304/304L Not required Design Temperature
(p. 92) (Licensor A) LP NITROGEN(Special Area)(LN) (ASTM A312-TP304/304L) -29 to 425 (C)
SLAG FINES(SLU) Design Pressure
ATMOSPHERIC VENT(AV) 19.0 to 5.5 (barg)

TANK VENT(TV)
21 01NM GASEOUS OXYGEN(LGOX) 0.0mm ALLOY 400 Not required Design Temperature
(p. 96) (Licensor A) (ASTM B165-N04400, -29 to 425 (C)
ASTM B725-N04400) Design Pressure
15.9 to 5.5 (barg)
22 01PV0 HYPOCHLORITE DOSING(PHY) 0.0mm CPVC Not applicable Design Temperature
(p. 99) (Licensor B) (ASTM F441-CPVC4120) 0 to 93 (C)
Design Pressure
Consult MFR
23 01R1 ATMOSPHERIC VENT(AV) 1.6mm 304/304L Not required Design Temperature
(p. 101) (Licensor A) TANK VENT(TV) (ASTM A312-TP304/304L) -29 to 425 (C)
DRAIN(DR) Design Pressure
PROCESS WATER(PW) 19.0 to 5.5 (barg)

PISTON FLUSH WATER(PFW)
RECYCLE WATER(RW)
LP CORROSIVE WATER
Doc. No. Rev. No.

2 12/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
24 01SA0 - Licensor A 0.0mm 304/304L Not required Design Temperature
(p. 104) (Licensor A) DEMINERALISED WATER(DW) (ASTM A312-TP304/304L, -29 to 425 (C)
(Licensor B) CLOSED DRAIN(DRC) ASTM A358-304/304L) Design Pressure
POTABLE WATER(WDR) 19.0 to 5.5 (barg)
- Licensor B 0.0mm 304/304L Not required Design Temperature

DEMINERALISED WATER(DW) (ASTM A312-TP304/304L, -46 to 425 (C)
DRAIN(DR) ASTM A358-304/304L) Design Pressure

PROCESS WATER(PW) 19.0 to 5.5 (barg)
RECYCLE WATER(RW)
SOUR PROCESS WATER(SPW)
LUBE OIL(LO)
25 01S0 OXYGEN SCAVENGER DOSING 0.0mm 316/316L Not required Design Temperature
(p. 108) (Licensor B) (POX) (ASTM A312-TP316/316L) -29 to 425 (C)
LP STEAM FOR SULPHUR PIT(LSS) Design Pressure
19.0 to 5.5 (barg)
26 01S1 AMMONIA STRIPPING 1.6mm 316/316L Not required Design Temperature
(p. 111) (Licensor B) (ASTM A312-TP316/316L) -29 to 425 (C)
Design Pressure
19.0 to 5.5 (barg)
27 01SS PROCESS WATER(PW) 0.0mm 304/304L Not required Design Temperature
(p. 114) (Licensor A) RECYCLE WATER(RW) (ASTM A312-TP304/304L) -29 to 425 (C)
SOUR PRCESS WATER(SPW) Design Pressure
DRAIN(DR) 19.0 to 5.5 (barg)
LUBE OIL(LO)
28 01T1 SULPHUR VAPOUR(SV) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 117) (CORE) LIQUID SULPHUR(LSU) (3.2mm) (ASTM A106-B) for thk>19.05mm -29 to 425 (C)
(Licensor B) SYNGAS SWEET(SGS) Design Pressure
SOUR GAS(PSOG) 19.6 to 5.5 (barg)

29 01T1J 150psi STEAM(LS) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
150# RF
(p. 120) (JACKET) (ASTM A106-B) for thk>19.05mm -29 to 425 (C)
13.6 to 10.6 (barg)
30 01U0 ATMOSPHERIC VENT(AV) 0.0mm 304/304L Not required Design Temperature
(p. 122) (Licensor A) TANK VENT(TV) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
19.0 to 5.5 (barg)
31 01U0B PROCESS CONDENSATE AGR & 0.0mm 304/304L NACE applies Design Temperature
(p. 125) (Licensor B) COSHIFT(PCR) (ASTM A312-TP304/304L, -46 to 300 (C)
WSA(HOLD) ASTM A358-304/304L) Design Pressure
LCPM 19.0 to 10.2 (barg)

32 01U0C VERY TOXIC SYNGAS(SGT) 0.0mm 304/304L NACE applies Design Temperature
(p. 130) (Licensor B) VERY TOXIC METHANOL SOLUTION (ASTM A312-TP304/304L, -196 to -47 (C)
(RECT) ASTM A358-304/304L) Design Pressure

VERY TOXIC DRAIN(DRRT) 19.0 (barg)
LOW PRESSURE CARBON
DIOXIDE(LCD)
MEDIUM PRESSURE CARBON
DIOXIDE(MCD)
SOUR GAS(PSOG)
WWR(HOLD)
COLD FLARE GASES(FLRC)
33 01Y0 PROCESS CONDENSATE AGR & 0.0mm 2205 DUPLEX SS Not required Design Temperature
(p. 135) (Licensor B) COSHIFT(PCR) (ASTM A790-S31803) -29 to 300 (C)
Design Pressure
20.0 to 10.2 (barg)
26 01Z0A AMMONIA STRIPPING 0.0mm HASTELLOY C-276 Not required Design Temperature
(p. 138) (Licensor B) (ASTM B619-N10276-Cl.1) -29 to 425 (C)
SOLUTION ANNEALED Design Pressure
Hold
Doc. No. Rev. No.

2 13/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
34 03A1 RECTISOL LEAN(RECL) 1.6mm CS Not required Design Temperature
(p. 140) (Licensor B) (API5L-B-PSL.1, -29 to 425 (C)
(Hydrogen content to be considered ASTM A671-CC65-Cl.22) Design Pressure
51.1 to 28.8 (barg)
up to 200℃)
35 03CS1 MP COND.(MC) 1.6mm CS Not required Design Temperature
(p. 143) (Licensor A) MP CARBON DIOXIDE(MCD) (API5L-B-PSL.1) -29 to 425 (C)
MP STEAM(MS) Design Pressure

NITROGEN(N) 51.1 to 28.8 (barg)
36 03CS2 - Licensor A 3.2mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 146) (Licensor A) MP COND.(MC) (API5L-B-PSL.1, for thk>19.05mm -29 to 425 (C)
(Licensor B) MP STEAM(MS) ASTM A671-CC65-Cl.22) Design Pressure
NITROGEN(N) 51.1 to 28.8 (barg)
- Licensor B
MP COND.(MC)
MP STEAM(MS)
NITROGEN(N)
PWF
SYNGAS RAW(SGR)
COOLING WATER SUPPLY(CWS)
COOLING WATER RETURN(CWR)
37 03D1 SYNGAS SWEET(SGS) 1.6mm IMPACT TESTED CS Not required Design Temperature
(p. 150) (Licensor B) MP LPG(MLPG) (ASTM A333-6) -46 to 350 (C)
Design Pressure
47.9 to 37.6 (barg)
37 03D2 RECTISOL SOLUTION RICH(RECR) 3.2mm IMPACT TESTED CS PWTH and NACE apply Design Temperature
(p. 153) (Licensor B) SYNGAS RAW(SGR) (ASTM A333-6) -46 to 350 (C)
Design Pressure
47.9 to 37.6 (barg)
38 03E1 DESUPER HEATER DISCHARGE 1.6mm 1.25%Cr 0.5%Mo Reqd per B31.3 Sec 331 Design Temperature
(p. 157) (Licensor B) (ASTM A335-P11, for thk>12.70mm 455 to 475 (C)
NEW A691-1.25Cr-Cl.22) Design Pressure
5.0 to 31.0 (barg)
300# RF
39 03G2 RECTISOL(RECR) 3.2mm IMPACT TESTED CS PWTH and NACE apply Design Temperature
(p. 158) (Licensor A) VERY TOXIC METHANOL SOLUTION (ASTM A106-B, A333-6) -29 to 425 (C)
(Licensor B) (RECT) Design Pressure
FLARE(FLR) 51.1 to 28.8 (barg)

40 03SA0 DEMINERALISED WATER(DW) 0.0mm 304/304L Not required Design Temperature
(p. 161) (Licensor B) (ASTM A312-TP304/304L, -46 to 425 (C)
ASTM A358-304/304L) Design Pressure
49.6 to 28.0 (barg)
41 03SS NOT USED 0.0mm 304/304L Not required Design Temperature
(p. 165) (Licensor A) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
49.6 to 28.0 (barg)
42 03U0B SLAG WATER(PW) 0.0mm 304/304L Not required Design Temperature
(p. 168) (Licensor B) VERY TOXIC METHANOL SOLUTION (ASTM A312-TP304/304L, -196 to 300 (C)
(RECT) ASTM A358-304/304L) Design Pressure

49.6 to 30.9 (barg)
43 03U0C SYNGAS RAW(SGR) 0.0mm 304/304L Not required Design Temperature
(p. 172) (Licensor B) REFRIGERANT PROPYLENE(RP) (ASTM A312-TP304/304L, -196 to 300 (C)
RECTISOL SOLUTION RICH(RECR) ASTM A358-304/304L) Design Pressure

49.6 to 30.9 (barg)
44 03X1 SYNGAS SWEET(SGS) 1.6mm Killed CS Not required Design Temperature
(p. 176) (Licensor B) (ASTM A106-B, A333-6) -29 to 425 (C)
Design Pressure
51.1 to 28.8 (barg)
45 03X2 SYNGAS SWEET(SGS) 3.2mm Killed CS Not required Design Temperature
(p. 179) (Licensor B) PROCESS GAS METHANATION (ASTM A106-B, A333-6) -29 to 425 (C)
(PGM) Design Pressure
51.1 to 28.8 (barg)
Doc. No. Rev. No.

2 14/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
46 03Y0 PROCESS CONDENSATE AGR & 0.0mm 2205 DUPLEX SS Not required Design Temperature
(p. 182) (Licensor B) COSHIFT(PCR) (ASTM A790-S31803) -29 to 300 (C)
Design Pressure
51.7 to 38.9 (barg)
47 06B1 CHLORIDE SCRUBBER BOTTOMS 1.6mm 2507 DUPLEX SS Not required Design Temperature
(p. 185) (Licensor A) WATER(WWG) (ASTM A790 S32750) -29 to 300 (C)
Design Pressure
103.4 to 77.7 (barg)
48 06C0 HP GASEOUS OXYGEN(HGOX) 0.0mm 304/304L Not required Design Temperature
(p. 188) (Licensor A) WET OXYGEN(WOX) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
99.3 to 56.0 (barg)
49 06C2 SLURRY FEED(SLU) 3.2mm 304/304L Not required Design Temperature
(p. 191) (Licensor A) HEATED SLURRY(SLU) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
99.3 to 56.0 (barg)
50 06CS1 MP BOILER FEED WATER(MBFW) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 195) (Licensor A) HP FUEL GAS(HFG) (API5L-B-PSL.1) for thk>19.05mm -29 to 425 (C)
HP CARBON DIOXIDE(HCD) Design Pressure
HP NITROGEN(HN) 102.1 to 57.5 (barg)

51 06CS2 COOLING WATER SUPPLY(CWS) 3.2mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 198) (Licensor B) COOLING WATER RETURN(CWR) (ASTM A106-B, A333-6) for thk>19.05mm -29 to 425 (C)
BLOWDOWN(BD) Design Pressure
HS, HIS 102.1 to 57.5 (barg)

52 06D1 SYNGAS SWEET(SGS) 1.6mm IMPACT TESTED CS PWHT applies Design Temperature
(p. 201) (Licensor B) (Hydrogen content to be considered (ASTM A333-6) -46 to 350 (C)
Design Pressure
up to 200℃)
HP LPG(HLPG) 102.1 to 75.1 (barg)
53 06D2 RECTISOL SOLUTION RICH(RECR) 3.2mm IMPACT TESTED CS PWTH and NACE apply Design Temperature
(p. 204) (Licensor B) SYNGAS RAW(SGR) (ASTM A333-6) -46 to 350 (C)
Design Pressure
102.1 to 75.1 (barg)
54 06E1 SYNGAS RAW(SGR) 1.6mm 1.25%Cr 0.5%Mo Reqd per B31.3 Sec 331 Design Temperature
600# RF
(p. 207) (Licensor B) HIGH PRESSURE NITROGEN(HN) (ASTM A335-P11, for thk>12.70mm -29 to 538 (C)
LS 129-31 Hydrogen Service A691-1.25Cr-Cl.22) Design Pressure
PROCESS GAS METHANATION 103.4 to 29.8 (barg)
(PGM)
55 06E2 SYNGAS RAW(SGR) 3.2mm 1.25%Cr 0.5%Mo Reqd per B31.3 Sec 331 Design Temperature
(p. 210) (Licensor B) LS 129-31 Hydrogen Service (ASTM A335-P11, for thk>12.70mm -29 to 538 (C)
A691-1.25Cr-Cl.22) Design Pressure

103.4 to 29.8 (barg)
56 06F1 ATMOSPHERIC VENT(AV) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 213) (Licensor A) CLOSED LOOP RETURN(CLR) (API5L-B-PSL.1) for thk>19.05mm -29 to 425 (C)
CLOSED LOOP SUPPLY(CLS) Design Pressure

HP PROCESS WATER(HPW) 102.1 to 57.5 (barg)
HP SLAG WATER(PW)
57 06J1 HP OXYGEN(WOX) 1.6mm 310 SS Not required Design Temperature
(p. 216) (Licensor A) (ASTM A312-TP310) -29 to 425 (C)
Design Pressure
99.3 to 64.2 (barg)
58 06L0 PROCESS CONDENSATE (PCR) 0.0mm 321 SS Not required Design Temperature
(p. 219) (Licensor B) (ASTM A312-TP321) -29 to 538 (C)
Design Pressure
99.3 to 50.0 (barg)
59 06L1 SYNGAS RAW(SGR) 1.6mm 321 SS Not required Design Temperature
(p. 222) (Licensor B) LS 129-31 Hydrogen Service (ASTM A312-TP321, -29 to 538 (C)
A358-321) Design Pressure
99.3 to 50.0 (barg)
Doc. No. Rev. No.

2 15/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
60 06NM GASEOUS OXYGEN(GOX) 0.0mm ALLOY 400 Not required Design Temperature
(p. 225) (Licensor A) (ASTM B165-N04400) -29 to 425 (C)
Design Pressure
82.7 to 63.3 (barg)
61 06P1 HP SLAG WATER(HPW) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 227) (Licensor A) SLAG(PW) (BASALT-LINED) for thk>19.05mm -29 to 425 (C)
(API5L-B-PSL.1) Design Pressure
102.1 to 57.5 (barg)
62 06Q1 HP SLAG WATER(HPW) 1.6mm 304/304L Not required Design Temperature
(p. 230) (Licensor A) SLAG(PW) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
99.3 to 56.0 (barg)
63 06SA0 HP DEMINERALISED WATER(HDW) 0.0mm 304/304L Not required Design Temperature
Design Pressure
99.3 to 56.0 (barg)
64 06SS SOUR PROCESS WATER(SPW) 0.0mm 304/304L Not required Design Temperature
(p. 237) (Licensor A) HP DEMINERALISED WATER(HDW) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
99.3 to 56.0 (barg)
65 06U0B HP PROCESS CONDENSATE METH 0.0mm 304/304L Not required Design Temperature
(p. 240) (Licensor B) (HPCM) (ASTM A312-TP304/304L, -46 to 300 (C)
SYNGAS RAW(SGR) ASTM A358-304/304L) Design Pressure

VERY TOXIC METHANOL SOLUTION 99.3 to 61.8 (barg)
(RECT)
RW(HOLD)
HPW(HOLD)
66 06U0C SYNGAS SWEET(SGS) 0.0mm 304/304L Not required Design Temperature
(p. 243) (Licensor B) PROCESS GAS METHANATION (ASTM A312-TP304/304L, -196 to -47 (C)
(PGM)(HOLD) ASTM A358-304/304L) Design Pressure

RECTISOL LEAN(RECL) 99.3 to 61.8 (barg)
RECTISOL RICH(RECR)
RECTISOL SEMI-LEAN(RECS)
600# RF
67 06V2 SYNGAS FLARE(FLR) 3.2mm 304/304L Not required Design Temperature
(p. 247) (Licensor A) HP SYNGAS(SG) (ASTM A312-TP304/304L, -29 to 425 (C)

ASTM A240-304/304L) Design Pressure
99.3 to 56.0 (barg)
68 06W2 SLURRY RETURN(SLU) 3.2mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 251) (Licensor A) (API5L-B-PSL.1) for thk>19.05mm -29 to 425 (C)
Design Pressure
102.1 to 57.5 (barg)
69 06X1 RECTISOL LEAN(RECL) 1.6mm Killed CS PWHT applies Design Temperature
(p. 255) (Licensor B) VERY TOXIC SYNGAS(SGT) (ASTM A106-B, A333-6, -29 to 425 (C)
SYNGAS RAW(SGR) A671-CC65-Cl.22) Design Pressure

HIGH PRESSURE CARBON 102.1 to 57.5 (barg)
DIOXIDE(HCD)
SYNGAS SWEET(SGS)
PROCESS GAS METHANATION
(PGM)
SYNTHETIC NATURAL GAS(SNG)
70 06X2 PROCESS GAS METHANATION 3.2mm Killed CS PWHT applies Design Temperature
(p. 259) (Licensor B) (PGM) (ASTM A106-B, A333-6, -29 to 425 (C)
A671-CC65-Cl.22) Design Pressure
102.1 to 57.5 (barg)
71 06Y0 SYNGAS RAW(SGR) 0.0mm 2205 DUPLEX SS Not required Design Temperature
(p. 263) (Licensor B) PROCESS CONDENSATE AGR & (ASTM A790-S31803) -29 to 300 (C)
COSHIFT(PCR) Design Pressure
103.4 to 77.7 (barg)
Doc. No. Rev. No.

2 16/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
72 06Z0 SYNGAS RAW(SGR) 0.0mm N08904 Not required Design Temperature
(p. 266) (Licensor B) PROCESS CONDENSATE AGR & (ASTM B677-N08904, -29 to 375 (C)
COSHIFT(PCR) ASTM B625-N08904) Design Pressure
102.6 to 56.5 (barg)
73 09C0 HP, HT GASEOUS OXYGEN(HGO2) 0.0mm 304/304L Not required Design Temperature
(p. 269) (Licensor A) HP GASEOUS OXYGEN(HGOX) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
148.9 to 84.0 (barg)
74 09C2 SLURRY FEED(SLU) 3.2mm 304/304L Not required Design Temperature
(p. 272) (Licensor A) HEATED SLURRY(SLU) (ASTM A312-TP304/304L) -29 to 425 (C)
Design Pressure
148.9 to 84.0 (barg)
75 09CS1 HP BOILER FEED WATER(HBFW) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 276) (Licensor A) (API5L-B-PSL.1) for thk>19.05mm -29 to 425 (C)
Design Pressure
153.2 to 86.3 (barg)
76 09CS2 BLOWDOWN HP(BDH) 3.2mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 279) (Licensor A) HP CONDENSATE(HC) (API5L-B-PSL.1) for thk>19.05mm -29 to 425 (C)
HP SATURATED STEAM(HS) Design Pressure
153.2 to 86.3 (barg)
77 09E1 HP SATURATED STEAM(HS) 1.6mm 1.25%Cr 0.5%Mo Reqd per B31.3 Sec 331 Design Temperature
(p. 282) (Licensor B) (ASTM A335-P11) for thk>12.70mm -29 to 538 (C)
Design Pressure
155.1 to 44.7 (barg)
78 09E2 HIGH PRESSURE SUPERHEATED 3.2mm 1.25%Cr 0.5%Mo Reqd per B31.3 Sec 331 Design Temperature
(p. 285) (Licensor B) START-UP STEAM(HSSS) (ASTM A335-P11) for thk>12.70mm -29 to 538 (C)
Design Pressure
155.1 to 44.7 (barg)
79 09J1 HP OXYGEN(WOX) 1.6mm 310 SS Not required Design Temperature
(p. 288) (Licensor A) HP, HT GASEOUS OXYGEN(HGO2) (ASTM A312-TP310) -29 to 425 (C)
Design Pressure
148.9 to 96.4 (barg)
80 09L0 RECTISOL LEAN(RECL) 0.0mm 321 SS Not required Design Temperature
(p. 291) (Licensor B) (ASTM A312-TP321) -196 to 425 (C)
Design Pressure
148.9 to 94.8 (barg) 900# RTJ
81 09NM GASEOUS OXYGEN(GOX) 0.0mm ALLOY 400 Not required Design Temperature
(p. 295) (Licensor A) HP, HT GASEOUS OXYGEN(HGO2) (ASTM B165-N04400 -29 to 425 (C)
HP GASEOUS OXYGEN(HGOX) ASTM B725-N04400) Design Pressure
124.1 to 94.9 (barg)
(p. 298) (Licensor A) METHANATION PROCESS (ASTM A312-TP304/304L) -29 to 425 (C)
WATER(MPW) Design Pressure

148.9 to 84.0 (barg)
84 09U0 RECTISOL LEAN(RECL) 0.0mm 304/304L Not required Design Temperature
(p. 301) (Licensor A) PROCESS GAS METHANATION (ASTM A312-TP304/304L, -46 to 300 (C)
NEW (PGM) ASTM A358-304/304L) Design Pressure
CHEMICAL DOSING(PCHM) 148.9 to 92.7 (barg)
85 09U0B RECTISOL LEAN(RECL) 0.0mm 304/304L Not required Design Temperature
(p. 304) (Licensor B) PROCESS GAS METHANATION (ASTM A312-TP304/304L, -46 to 300 (C)
(PGM) ASTM A358-304/304L) Design Pressure

86 09U0C RECTISOL LEAN(RECL) 0.0mm 304/304L Not required Design Temperature
(p. 307) (Licensor B) PROCESS GAS METHANATION (ASTM A312-TP304/304L, -196 to -47 (C)
(PGM) ASTM A358-304/304L) Design Pressure

Doc. No. Rev. No.

2 17/334
EP242-11001
(ATTACHMENT #1)
No. Allow. Class
87 09X1 RECTISOL LEAN(RECL) 1.6mm Killed CS Reqd per B31.3 Sec 331 Design Temperature
(p. 311) (Licensor B) HIGH PRESSURE CARBON (ASTM A106-B) for thk>19.05mm -29 to 425 (C)
DIOXIDE(HCD) Design Pressure
PROCESS GAS METHANATION 153.2 to 86.3 (barg)
(PGM)
LPG BLENDING SYSTEM
SYNTHETIC NATURAL GAS(SNG)
88 09Y0 SYNGAS RAW(SGR) 0.0mm 2205 DUPLEX SS Not required Design Temperature
(p. 314) (Licensor A) PROCESS CONDENSATE AGR & (ASTM A790-S31803) -29 to 300 (C)
COSHIFT(PCR) Design Pressure

155.1 to 116.6 (barg)
89 15CS1 HP BOILER FEED WATER(HBFW) 1.6mm CS Reqd per B31.3 Sec 331 Design Temperature
(p. 316) (Licensor A) (Valves Buttwelded.) (ASTM A106-B, for thk>19.05mm -29 to 425 (C)
(Licensor B) A671-CC65-Cl.22) Design Pressure
255.3 to 143.8 (barg)
90 15H1 SUPERHEATED 1.6mm 2.25%Cr 1.0%Mo NACE applies Design Temperature
(p. 319) (Licensor B) HIGH TEMPERATURE STEAM(HSS) (ASTM A335-P22, -29 to 538 (C)
PROCESS GAS METHANATION ASTM A 691- 2.25Cr-Cl.41) Design Pressure

(PGM) 258.6 to 92.2 (barg)
91 15M2 CHAR(P) 3.2mm 304/304L Not required Design Temperature
1500# RTJ
Design Pressure
248.2 to 140.0 (barg)
92 15N1 HP SYNGAS(SG) 1.6mm 304/304L Not required Design Temperature
Design Pressure
248.2 to 140.0 (barg)
(p. 328) (Licensor A) METHANATION PROCESS (ASTM A312-TP304/304L) -29 to 425 (C)
WATER(MPW) Design Pressure

248.2 to 140.0 (barg)
Doc. No. Rev. No. Page
TECHNICAL SPECIFICATION
2 18/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01A1

RATING ASME 150#
CORR. ALLOWANCE 1.6MM DES. TEMP.(C) -29 (MDMT) to 425 (NOTE 35)
TYPICAL SERVICE DES. PRES.(barg) 19.6 to 5.5
- LICENSOR A AV,FLU,SG,FGO,PW,RW,PFW,SLU,TV PWHT / NACE Not required
- LICENSOR B
SIZE RANGE MATERIAL PROD. END WALL THK. REMARKS NOTES
PIPE (01,02)
15 - 20 API5L-B-PSL.1 SMLS BE SCH160
450 - 600 API5L-B-PSL.1 DSAW BE SCH20
650 - 750 API5L-B-PSL.1 DSAW BE STD
900 - 900 API5L-B-PSL.1 DSAW BE 11.13MM
NIPPLE (02,03)
15 - 40 API5L-B-PSL.1 SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A234-WPB SMLS BBE To match pipe thickness
ELBOW/TEE/REDUCER (02,03)
15 - 400 A234-WPB SMLS BW To match pipe thickness
450 - 900 A234-WPB WELD BW To match pipe thickness
CAP (02,03)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
FLANGEOLET
15 - 80 A105 150# RF To match pipe thickness (82)
ELBOLET
15 - 15 A105 BW To match pipe thickness
WELDOLET (02,03,05)
SIZE RANGE MATERIAL RAT'G TYPE FACE REMARKS NOTES
FLANGE (02)
15 - 600 A105 150# WN RF
ASME
750 - 900 A105 150# WN RF
B16.47-A
100 - 600 A105 150# WN RF WITH J.B
WITH J.B
750 - 900 A105 150# WN RF ASME
B16.47-A
15 - 600 A105 150# WN FF (11,14)
ASME
750 - 900 A105 150# WN FF (11,14)
B16.47-A
15 - 600 A105 300# WN RF (12)
ASME
750 - 900 A105 300# WN RF (12)
B16.47-A
15 - 600 A105 600# WN RF (12)
ASME
750 - 900 A105 600# WN RF (12)
B16.47-A
80 - 150 A105 900# WN RTJ (82)
RED. FLANGE (02)
50 - 150 A105 150# WN RF
BLIND FLANGE
15 - 600 A105 150# BLIND RF
ASME
650 - 900 A105 150# BLIND RF
B16.47-A
LINE BLANK
150 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
2 19/334
EP242-11001
(ATTACHMENT #1)

RATING ASME 150#
- LICENSOR B
SIZE RANGE MATERIAL RAT'G FACE TYPE REMARKS NOTES
GASKET
15 - 600 FLEX.GRAPH.+304SS 150# RF 1.6MM
ASME
B16.47-A
15 - 600 FLEX.GRAPH.+304SS 300# RF 1.6MM (12)
ASME
B16.47-A
15 - 600 SW(304+GRAP)IO:304/CS 600# RF 4.5MM (12)
ASME
650 - 900 SW(304+GRAP)IO:304/CS 600# RF 4.5MM (12)
B16.47-A
15 - 600 FLEX.GRAPH.+304SS 150# FF 1.6MM (11,14)
ASME
B16.47-A
BOLT/NUT
A193-B7/A194-2H(Zn-CHROMATE) STUD/H.HEX
SIZE RANGE BODY/TRIM MATERIAL RAT'G CONN. TYPE REMARKS NOTES
GATE
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101) (08,09)
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y (GA-102A) (08,09)
350 - 600 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GA-132A) (08,09)
GLOBE
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GL-114) (08,09)
50 - 150 A216-WCB/13Cr+HF 150# RF BB OS&Y (GL-115) (08,09)
CHECK
15 - 40 A105/13Cr+HF 150# RF BC LIFT (CH-113) (08,09,61)
50 - 600 A216-WCB/13Cr+RTFE 150# WAFER DUAL PLATE (CH-114) (07,08,09,63-2,160)
BALL
15 - 150 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF RED. BORE F.S (BA-121) (08,09)
200 - 600 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF RED. BORE F.S GEAR (BA-122) (08,09)
15 - 150 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF RED. F.S EXT.BONNET (BA-121E) (08,09)
15 - 150 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF FULL BORE F.S (BA-123) (08,09)
200 - 600 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF FULL BORE F.S GEAR (BA-124) (08,09)
15 - 150 A216-WCB/Cr or Ni Pl.CS+RTFE 150# RF FULL F.S EXT.BONNET (BA-123E) (08,09)
3-WAY BALL
REFERENCE
50 - 150 A216-WCB/316+RTFE 150# RF FULL BORE F.S (08,09)
(BA-109)
BUTTERFLY
50 - 150 A216-WCB/17-4PH+PTFE 150# LUG LEVER (BF-106) (08,09,15-2)
200 - 600 A216-WCB/17-4PH+PTFE 150# LUG GEAR (BF-107) (08,09,15-2)
PLUG
15 - 150 A216-WCB/DI+PTFE 150# RF REGULAR (PL-105) (08,09)
200 - 300 A216-WCB/DI+PTFE 150# RF REGULAR GEAR (PL-106) (08,09)
KNIFE GATE
50 - 50 Ni-RESIST CI/316+BUNA-N 150# WAFER BONNETLESS (KG-101) (08,09)
80 - 300 A395/316+URETHANE 150# WAFER BONNETLESS (KG-103) (08,09)
350 - 600 A395/316+URETHANE 150# WAFER BONNETLESS GEAR (KG-104) (08,09)
2 20/334
EP242-11001
(ATTACHMENT #1)

RATING ASME 150#
- LICENSOR B
Notes :
01 If a pipe schedule is shown below "SCH/RAT" it shall be adequate for the full rating.
02 All butt-welding component thickness shall match the pipe thickness.
03 Threaded joints are not permitted.
Integrally reinforced branch connections outside the sizes shown in the branch connection table are permitted. Weld thickness of
05
integrally reinforced branch connections shall be checked to determine if PWHT is required.
07 These valves have no flanges but are installed between line flanges with extra-length bolts.
Valve description and size range taken from licensor 'Piping Material Guidelines' document no. RA-PPG-001 rev C. Licensor has
08
recommended using 'Noble' valves for this service.
Pressure and Temperature Rating can be limited by certain components permitted by this Practice. Manufacturer's recommended
09
pressure-temperature restrictions shall be consulted.
11 Flat-faced flanges shall be provided adjacent to flat-faced valves.
12 These flanges shall be used only to match flange connections at control valves and special equipment.
14 Full-face gaskets shall be used at flat-faced flanges.
These valves should not be used for dead end service. These valves should not be installed with the seat and seat retainer ring on
15-2
the upstream or high pressure side of the valve.
Minimum Design Metal Temperature (MDMT) is limited to the minimum temperature allowed for the listed material curve in Fig.
35
323.2.2 of ASME B31.3.
61 These check valves shall be installed in a horizontal position with cover up.
63-2 These check valves shall be installed in a horizontal position with hinge pin horizontal or a vertical position with upward flow.
82 Special use only.
160 Wafer style check valves shall be limited to 260℃ maximum.
163 These items shall be used only for hydrotest vent/drain.
2 21/334
(ATTACHMENT #1) EP242-11001
DIAGRAM OF BRANCH CONNECTION
CLASS: 01A1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 750 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
Header Size (DN)
150 W W W W N N B B
200 W W W W N N N B B
250 W W W W N N N N B B
300 W W W W W W W N N B B
350 W W W W W W W N N N B B
400 W W W W W W W N N N N B B
450 W W W W W W W W N N R R B B
500 W W W W W W W W R R R R R B B
600 W W W W W W W W W R R R R R B B
750 W W W W W W W W W R R R R R R B B
900 W W W W W W W W W W W W R R R R B B
Abbreviation
B Buttwelding Tee
W Weldolet or Sweepolet
R Nozzle Weld with Reinforcing Pad
N Nozzle weld without Pad (Stub-in)
2 22/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01A1B

RATING ASME 150#
- LICENSOR A PWHT / NACE Not required
- LICENSOR B AV, FLU, SLU, TV, PW, RW, PFW
PIPE (01,02)
1150 - 1200 A671-CC65-Cl.22 EFW BE XS
1300 - 1300 A671-CC65-Cl.22 EFW BE 14.27MM
1400 - 1400 A671-CC65-Cl.22 EFW BE 15.88MM
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 50 A105 THRD 3000#
PLUGS (163)
15 - 50 A105 THRD HEX
CAP (02,03)
WELDOLET (02,03,05)
FLANGE (02)
15 - 40 A105 300# WN RF
50 - 600 A105 150# WN RF
ASME
650 - 1400 A105 150# WN RF
B16.47-A
100 - 600 A105 150# WN RF WITH J.B
WITH J.B
650 - 1400 A105 150# WN RF ASME
B16.47-A
100 - 150 A105 900# WN RTJ WITH J.B (82)
15 - 40 A105 300# WN FF (11,14)
50 - 600 A105 150# WN FF (11,14)
ASME
650 - 1400 A105 150# WN FF (11,14)
B16.47-A
50 - 600 A105 300# WN RF (12,82)
ASME
650 - 1400 A105 300# WN RF (12,82)
B16.47-A
15 - 600 A105 600# WN RF (82)
ASME
650 - 1400 A105 600# WN RF (82)
B16.47-A
50 - 50 A105 1500# WN RTJ (82)
80 - 600 A105 900# WN RTJ (82)
RED. FLANGE (02)
50 - 50 A105 150# WN RF
2 23/334
EP242-11001
(ATTACHMENT #1)

RATING ASME 150#
BLIND FLANGE
15 - 40 A105 300# BLIND RF
50 - 600 A105 150# BLIND RF
ASME
650 - 1400 A105 150# BLIND RF
B16.47-A
50 - 600 A105 300# BLIND RF (82)
ASME
650 - 1400 A105 300# BLIND RF (82)
B16.47-A
15 - 600 A105 600# BLIND RF (82)
ASME
650 - 1400 A105 600# BLIND RF (82)
B16.47-A
LINE BLANK
15 - 40 A105 300# FIG-8 FF
50 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
ASME
650 - 1400 A105 150# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
ASME
B16.47-A
ASME
B16.47-A
15 - 600 SW(304+GRAP)IO:304/CS 600# RF 4.5MM (82)
ASME
650 - 1400 SW(304+GRAP)IO:304/CS 600# RF 4.5MM (82)
B16.47-A
BOLT/NUT
2 24/334
EP242-11001
(ATTACHMENT #1)

RATING ASME 150#
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09)
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y (GA-102) (09)
350 - 600 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GA-132) (09)
ASME
650 - 1400 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR B16.47-A (09)
(GA-103)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-119) (09)
50 - 200 A216-WCB/13Cr+HF 150# RF BB OS&Y (GL-102) (09)
250 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GL-103) (09)
CHECK
15 - 40 A105/13Cr+HF 300# RF BC LIFT (CH-122) (61)
50 - 600 A216-WCB/13Cr+HF 150# RF BC SWING (CH-102) (62)
ASME
650 - 1400 A216-WCB/13Cr+HF 150# RF BC SWING B16.47-A (62)
(CH-103)
50 - 600 A216-WCB/13Cr 150# WAFER DUAL PLATE (CH-104) (07,26-2,63-2)
ASME
650 - 1400 A216-WCB/13Cr 150# WAFER DUAL PLATE B16.47-A (07,26-2,63-2)
(CH-105)
BALL
15 - 40 A216-WCB/316+RTFE 300# RF RED. BORE F.S (BA-107) (09)
200 - 600 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR (BA-105) (09)
ASME
650 - 1400 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-106)
50 - 150 A216-WCB/316+RTFE 150# RF FULL BORE F.S (BA-103) (09)
200 - 600 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR (BA-108) (09)
ASME
650 - 1400 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (09)
(BA-109)
BUTTERFLY
80 - 150 A216-WCB/316+RTFE 150# LUG LEVER (BF-101) (09)
200 - 600 A216-WCB/316+RTFE 150# LUG GEAR (BF-102) (09)
ASME
650 - 1400 A216-WCB/316+RTFE 150# LUG GEAR B16.47-A (09)
(BF-103)
PLUG
15 - 40 A216-WCB/316+PTFE 300# RF REGULAR (PL-103) (09)
200 - 450 A216-WCB/316+PTFE 150# RF REGULAR GEAR (PL-102) (09)

2 25/334
EP242-11001
(ATTACHMENT #1)

RATING ASME 150#
Notes :
05
09
26-2 These wafer style check valves shall be limited to 260℃ maximum and shall be used only if indicated on the P&ID.
35 323.2.2 of ASME B31.3.
62 These check valves shall be installed in a horizontal position with cover up or in a vertical position with upward flow.
2 26/334
CLASS: 01A1B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000105011001150120013001400
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
300 W W W W N N N N N B B
350 W W W W N N N N N N B B
400 W W W W N N N N N N N B B
Header Size (DN)
450 W W W W N N N N N N R R B B
500 W W W W W W W W W W R R R B B
600 W W W W W W W W W W R R R R B B
650 W W W W W W W W W W R R R R R B B
700 W W W W W W W W W W R R R R R R B B
750 W W W W W W W W W W R R R R R R R B B
800 W W W W W W W W R R R R R R R R R R B B
850 W W W W W W W W R R R R R R R R R R R B B
900 W W W W W W W W R R R R R R R R R R R R B B
950 W W W W W W W W R R R R R R R R R R R R R B B
1000 W W W W W W W W R R R R R R R R R R R R R R B B
1050 W W W W W W W W R R R R R R R R R R R R R R R B B
1100 W W W W W W W W R R R R R R R R R R R R R R R R B B
1150 W W W W W W W W R R R R R R R R R R R R R R R R R B B
1200 W W W W W W W W R R R R R R R R R R R R R R R R R R B B
1300 W W W W W W W W R R R R R R R R R R R R R R R R R R R B B
1400 W W W W W W W W R R R R R R R R R R R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 27/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B SGR,SGS,SV, PSOG(NOTE 161)
PIPE (01,02)
15 - 20 API5L-B-PSL.1 SMLS BE XXS
NIPPLE (02,03)
SWAGE (02,03)
CAP (02,03)
THREDOLET (163)
15 - 50 A105 THRD 3000#
PLUGS (163)
15 - 50 A105 THRD HEX
ELBOLOET (02,05)
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 300# WN RF
50 - 600 A105 150# WN RF
ASME
650 - 750 A105 150# WN RF
B16.47-A
15 - 40 A105 300# WN RF WITH J.B
50 - 600 A105 150# WN RF WITH J.B
WITH J.B
650 - 750 A105 150# WN RF ASME
B16.47-A
50 - 600 A105 300# WN RF (12,82)
ASME
650 - 750 A105 300# WN RF (12,82)
B16.47-A
25 - 50 A105 600# WN RF (12,82)
RED. FLANGE (02)
80 - 450 A105 150# WN RF
700 - 800 A105 150# WN RF
BLIND FLANGE
15 - 40 A105 300# BLIND RF
50 - 600 A105 150# BLIND RF
ASME
650 - 750 A105 150# BLIND RF
B16.47-A
50 - 600 A105 300# BLIND RF (12)
ASME
650 - 750 A105 300# BLIND RF (12)
B16.47-A
2 28/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
LINE BLANK
15 - 40 A105 300# FIG-8 FF
50 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
ASME
650 - 750 A105 150# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
ASME
B16.47-A
BOLT/NUT
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09)
ASME
(GA-103)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-119) (09)
CHECK
ASME
(CH-103)
50 - 600 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE (CH-104) (07,26-2,63-2)
ASME
650 - 750 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE B16.47-A (07,26-2,63-2)
(CH-105)
BALL
ASME
(BA-106)
15 - 40 A216-WCB/316+RTFE 300# RF RED. F.S EXT.BONNET (BA-107E) (09)
200 - 600 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR (BA-108) (09)
ASME
650 - 750 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08,09)
(BA-109)
BUTTERFLY
2 29/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
PLUG
Notes :
05
08
09
35
323.2.2 of ASME B31.3.
161 Inclusion of Sour Gas (PSOG) in this pipeclass to be confirmed at detail design engineering.
2 30/334
CLASS: 01A2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
Header Size (DN)
150 W W W W N N B B
Abbreviation
B Buttwelding Tee
2 31/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01B0
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) -29 to 300 (NOTE 100)
- LICENSOR A PWHT / NACE NACE applies
- LICENSOR B PSOG,WSA
PIPE (01,100)
15 - 20 A790-S32750(NACE) SMLS BE SCH80S
550 - 550 A790-S32750(NACE) SMLS BE SCH10
NIPPLE (02,114)
15 - 40 A790-S32750(NACE) SMLS BBE To match pipe thickness L=3"
SWAGE (02,114)
15 - 100 A815-S32750(NACE) SMLS BBE To match pipe thickness
15 - 600 A815-S32750(NACE) SMLS BW To match pipe thickness
CAP (02,114)
15 - 600 A815-S32750(NACE) SMLS BW To match pipe thickness
PLUGS (163)
15 - 50 A182-F53(NACE) THRD HEX
THREDOLET (163)
15 - 50 A182-F53(NACE) THRD 3000#
WELDOLET (02,81,114)
80 - 600 A182-F53(NACE) BW To match pipe thickness
FLANGE (02)
15 - 600 A182-F53(NACE) 150# WN RF
25 - 600 A182-F53(NACE) 150# WN RF WITH J.B
15 - 500 A182-F53(NACE) 300# WN RF (82)
BLIND FLANGE
15 - 600 A182-F53(NACE) 150# BLIND RF
LINE BLANK
15 - 350 A182-F53(NACE) 150# FIG-8 FF
400 - 600 A182-F53(NACE) 150# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 150# RF 4.5MM (NACE)
15 - 600 SW(316+GRAP)IO:316 300# RF 4.5MM (NACE) (82)
BOLT/NUT
A193-B7M/A194-2HM STUD/H.HEX
GATE
15 - 40 A182-F53(NACE)/DUPLEX 2507 150# RF BB OS&Y (GA-604) (09)
50 - 300 A351-CD4MCu(NACE)/DUPLEX 2507 150# RF BB OS&Y (GA-605) (09)
350 - 600 A351-CD4MCu(NACE)/DUPLEX 2507 150# RF BB OS&Y GEAR (GA-606) (09)
GLOBE
15 - 40 A182-F53(NACE)/DUPLEX 2507 150# RF BB OS&Y (GL-604) (09)
50 - 200 A351-CD4MCu(NACE)/DUPLEX 2507 150# RF BB OS&Y (GL-605) (09)
250 - 300 A351-CD4MCu(NACE)/DUPLEX 2507 150# RF BB OS&Y GEAR (GL-606) (09)
CHECK
15 - 40 A182-F53(NACE)/DUPLEX 2507 300# BW BC LIFT (CH-604) (61)
50 - 600 A182-F53(NACE)/DUPLEX 2507 150# RF BC SWING (CH-605) (62)
50 - 600 A351-CD4MCu(NACE)/DUPLEX 2507 150# WAFER DUAL PLATE (CH-606) (07,26,63)
BUTTERFLY
150 - 150 A351-CD4MCu(NACE)/DUPLEX 2507 150# WAFER LEVER (BF-606)
200 - 200 A351-CD4MCu(NACE)/DUPLEX 2507 150# WAFER GEAR (BF-606)
2 32/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B PSOG,WSA
Note :
- Material : 2507 DUPLEX SS - Not to be used over 315℃
09
26 These check valves shall be used only if indicated on the P&ID.
63 These check valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow.
81 Integrally reinforced branch connections, tees, and reducing tees are permitted as an acceptable alternative branch connection.
100 Not to be used over 315℃.
2 33/334
CLASS: 01B0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W N B B
150 W W W W N N B B
450 W W W W N N N N N N N N B B
500 W W W W N N N N N N N N N B B
600 W W W W N N N N N N N N N N B B
Abbreviation
B Buttwelding Tee
2 34/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01C0
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) -29 to 425
- LICENSOR A LGOX,PVO(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 20 A312-TP304/304L SMLS BE SCH80S
25 - 100 A312-TP304/304L SMLS BE SCH40S
150 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 400 A312-TP304/304L DSAW BE SCH10S
450 - 500 A312-TP304/304L DSAW BE SCH10
600 - 600 A312-TP304/304L DSAW BE SCH20
BEND (02,103)
15 - 300 A312-TP304/304L SMLS BE To match pipe thickness 3D
350 - 600 A312-TP304/304L DSAW BE To match pipe thickness 3D
NIPPLE (02,103)
15 - 40 A312-TP304/304L SMLS BBE To match pipe thickness L=3"
SWAGE (02,103)
15 - 100 A403-WP304/304L SMLS BBE To match pipe thickness
15 - 300 A403-WP304/304L SMLS BW To match pipe thickness
350 - 600 A403-WP304/304L WELD BW To match pipe thickness
CAP (02,103)
THREDOLET (163)
15 - 50 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 50 A182-F304/304L THRD HEX
50 - 600 A182-F304/304L BW To match pipe thickness
FLANGE (02,103)
15 - 600 A182-F304/304L 150# WN RF
25 - 100 A182-F304/304L 600# WN RF
25 - 50 A182-F304/304L 1500# WN RTJ
25 - 600 A182-F304/304L 150# WN RF WITH J.B
BLIND FLANGE
15 - 600 A182-F304/304L 150# BLIND RF
LINE BLANK
15 - 350 A240-304/304L 150# FIG-8 FF
400 - 600 A240-304/304L 150# BLK&SPC FF
GASKET
OXYGEN
15 - 600 SW(304+GRAP)IO:304 150# RF 4.5MM (105)
SERVICE
OXYGEN
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (105)
SERVICE
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX
2 35/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A LGOX,PVO(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A182-F316/ALLOY400 150# RF BB OS&Y (GA-220) (08-3,09)
50 - 300 A351-CF8M/ALLOY400 150# RF BB OS&Y (GA-226) (08-3,09)
350 - 600 A351-CF8M/ALLOY400 150# RF BB OS&Y GEAR (GA-314) (08-3,09)
GLOBE
15 - 40 A182-F316/ALLOY400 150# RF BB OS&Y (GL-220) (08-3,09)
50 - 200 A351-CF8M/ALLOY400 150# RF BB OS&Y (GL-228) (08-3,09)
250 - 300 A351-CF8M/ALLOY400 150# RF BB OS&Y GEAR (GL-226) (08-3,09)
CHECK
15 - 40 A182-F316/ALLOY400 150# RF BC SWING (CH-240) (62)
50 - 600 A351-CF8M/ALLOY400 150# RF BC SWING (CH-247) (62)
80 - 600 A351-CF8M/ALLOY400 150# WAFER DUAL PLATE (CH-241) (07,26,63)
BALL
15 - 150 A351-CF8M/ALLOY400+RTFE 150# RF FULL BORE F.S (BA-240) (08-3,09)
200 - 250 A351-CF8M/ALLOY400+RTFE 150# RF FULL BORE F.S GEAR (BA-241) (08-3,09)
Notes :
08-3 Full port valves shall be used Oxygen lines.
09
The use of copper or nickel alloy materials should be considered in piping systems in which high-velocity and/or high-turbulent flow
99 exists downstream of pressure let-down valves. Guidelines contained in CGA G4.4, Para 4.3.3.4 shall be followed for the selection
of materials in such areas.
All materials shall be cleaned in accordance with Compressed Gas Association Pamphlet G4.1, Compressed Gas Association
102
pamphlet G4.4 and ASTM G-93.
103 The selection and use of materials shall be consistent with the velocity limits recommended in CGA G -4.4.
105 Certification which is tested to use GOX shall be supplied when graphite material uses for gasket.
2 36/334
CLASS: 01C0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W B B B
200 W W W W W W B B B
250 W W W W W W B B B B
300 W W W W W W W B B B B
350 W W W W W W W B B B B B
400 W W W W W W W B B B B B B
450 W W W W W W W W B B B B B B
500 W W W W W W W W B B B B B B B
600 W W W W W W W W W B B B B B B B
Abbreviation
B Buttwelding Tee
2 37/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01CH0
RATING ASME 150#
TYPICAL SERVICE DES. PRES.(barg) CONSULT MANUFATURER
- LICENSOR B PAC2
PIPE (31,42,43)
20 - 40 A53-B(PTFE.L) SMLS 150# FF SCH40 ASTM F1545
50 - 150 A53-B(PTFE.L) ERW 150# FF SCH40 ASTM F1545
ELBOW/REDUCER/TEE (33,42)
20 - 40 A234-WPB(PTFE.L) SMLS 150# FF To match pipe thickness ASTM F1545
50 - 300 A234-WPB(PTFE.L) WELD 150# FF To match pipe thickness ASTM F1545
STUB-END
20 - 40 A234-WPB(PTFE.L) SMLS 150# FF To match pipe thickness ASTM F1545
50 - 300 A234-WPB(PTFE.L) WELD 150# FF To match pipe thickness ASTM F1545
COUPLING (33,42)
20 - 50 A105(PTFE.L) SW 3000#
INSTRUMENT TEE (33,36,42)
20 - 50 A105(PTFE.L) 150# FF To match pipe thickness ASTM F1545
FLANGE (31,32)
15 - 300 A105 150# LJ FF
15 - 300 A105 300# LJ FF
BLIND FLANGE (31,33)
15 - 300 A105(PTFE.L) 150# BLIND FF ASTM F1545
GASKET (38)
15 - 300 PTFE 150# RF 1.6MM
BOLT/NUT (41)
BALL
20 - 150 A395/DI(PFA.L) 150# RF RED. BORE F.S (BA-950)
200 - 300 A395/DI(PFA.L) 150# RF RED. BORE F.S GEAR (BA-951)
20 - 150 A395/DI(PFA.L) 150# RF FULL BORE F.S (BA-952)
200 - 300 A395/DI(PFA.L) 150# RF FULL BORE F.S GEAR (BA-953)
PLUG
25 - 150 A395/DI(PFA.L) 150# RF REGULAR (PL-950)
200 - 300 A395/DI(PFA.L) 150# RF REGULAR GEAR (PL-951)
CHECK
25 - 200 A395/DI(PFA.L) 150# RF BC BALL (CH-950) (62)
80 - 300 A395/DI(PFA.L) 150# RF BC SWING (CH-951) (64)
BUTTERFLY
50 - 150 A395/DI(PFA.L) 150# WAFER LEVER (BF-950)
200 - 300 A395/DI(PFA.L) 150# WAFER GEAR (BF-951)
2 38/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01CH0
RATING ASME 150#
- LICENSOR B PAC2
Notes :
Plastic lining in pipe to comply with ASTM F1545 standard specification for PTFE plastic-lined ferrous metal pipe, fitting, and
31
flanges.
Flanged ends may be moulded raised face with threaded ductile iron flanges, lap joint flanges with lap joint ends on lined pipe, or
two-piece lap joint flanges with lap joint ends on lined pipe that meets class 150 dimensions. Inner flange corners are to be
32
chamfered a minimum of 1/4" or per the manufacturer's specifications. Threaded flanges to be used for fabrication of metal
components only.
Fittings to comply with ASTM F1545 standard specification for PTFE plastic-lined ferrous metal pipe and fittings. All wetted
33
surfaces are to be fully lined. Fittings to comply with ASTM dimensional requirements B16.42 or B16.5.
Instrument tee to slip between two flanges on the main run. Branch connection is to have a lap joint flanged end with class 150
36
flange for the branch size.
Gaskets are not required for connections between plastic lined components. 3/16" PTFE envelope gaskets are required
38
for mating plastic-lined components
40 Consult manufacturer for temperature, pressure, and vacuum rating limits for specific service.
41 Torque to manufacturer's specifications. Retorque per manufacturer's specifications.
42 Welding or heating of metal surfaces of plastic-lined pipe is not permitted.
Bending of plastic-lined pipe is to be undertaken only where permitted by the manufacturer and to the manufacturer's
43
specification.
64 Install in horizontal position or in vertical position with upward flow.
2 39/334
CLASS: 01CH0
Branch Size (DN)

20 25 40 50 80 100 150 200 250 300
20 B
25 B B
40 B B B
Header Size (DN)
50 B B B B
80 C C C B B
100 C C C C B B
150 C C C C B B B
200 C C C C B B B B
250 C C C C B B B B B
300 C C C C N B B B B B
Abbreviation
B Buttwelding Tee
C Half Coupling
2 40/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01CS1
RATING ASME 150#
- LICENSOR A LFG,RAW,PVN PWHT / NACE Not required
- LICENSOR B LN,LBFW,WW
PIPE (01,02)
15 - 20 API5L-B-PSL.1 SMLS PE SCH160
1150 - 1150 A671-CC65-Cl.22 EFW BE 11.91MM
1200 - 1200 A671-CC65-Cl.22 EFW BE XS
1300 - 1300 A671-CC65-Cl.22 EFW BE 14.27MM
NIPPLE (02)
15 - 40 API5L-B-PSL.1 SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 API5L-B-PSL.1 SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A234-WPB SMLS PBE To match pipe thickness (03-2)
50 - 100 A234-WPB SMLS BLE/PSE To match pipe thickness (03-2)
ELBOW/TEE/REDUCER (02)
15 - 40 A105 SW 3000#
1150 - 1150 A234-WPB WELD BW To match pipe thickness RT 100%
CAP (02)
15 - 40 A105 THRD 3000#
SOCKOLET/FULL COUPLING/UNION (02)
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 50 A105 THRD 3000#
PLUGS (02)
15 - 40 A105 THRD HEX (03-2)
WELDOLET (02,05)
2 41/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
FLANGE (02)
15 - 40 A105 150# SW RF
50 - 600 A105 150# SO RF
ASME
650 - 1300 A105 150# WN RF
B16.47-A
50 - 600 A105 150# SO RF WITH J.B
WITH J.B
650 - 1300 A105 150# WN RF ASME
B16.47-A
200 - 600 A105 600# WN RF WITH J.B
15 - 40 A105 150# SW FF (11,14)
50 - 600 A105 150# SO FF (11,14)
ASME
650 - 750 A105 150# WN FF (11,14)
B16.47-A
15 - 40 A105 300# SW RF (12,82)
50 - 600 A105 300# WN RF (12,82)
ASME
650 - 750 A105 300# WN RF (12,82)
B16.47-A
15 - 40 A105 600# SW RF (82)
50 - 600 A105 600# WN RF (82)
15 - 40 A105 1500# SW RTJ (82)
50 - 50 A105 1500# WN RTJ (82)
80 - 600 A105 900# WN RTJ (82)
BLIND FLANGE
15 - 600 A105 150# BLIND RF
ASME
650 - 1300 A105 150# BLIND RF
B16.47-A
15 - 50 A105 300# BLIND RF
LINE BLANK
15 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
ASME
650 - 1300 A105 150# BLK&SPC FF
B16.47-A
15 - 350 A105 300# FIG-8 FF
GASKET
ASME
B16.47-A
ASME
B16.47-A
ASME
B16.47-A
15 - 50 SOFT IRON 1500# RTJ OVAL RING (82)
BOLT/NUT
2 42/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105)
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y (GA-102)
350 - 600 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GA-132)
ASME
650 - 1300 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR B16.47-A
(GA-103)
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101) (15)
(GA-132)
WITH BY
350 - 600 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR PASS DN20
GLOBE V/V
(GL-101)
15 - 40 A105/13Cr+HF 800# SW/NPT BB OS&Y (GA-104) (06)
GLOBE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GL-101)
50 - 200 A216-WCB/13Cr+HF 150# RF BB OS&Y (GL-102)
250 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GL-103)
CHECK
15 - 40 A105/13Cr+HF 800# SW BC LIFT (CH-101) (61)
ASME
(CH-103)
50 - 600 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE (CH-104) (07,26-2,63)
ASME
650 - 1300 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-105)
BALL
ASME
(BA-106)
15 - 150 A216-WCB/316+RTFE 150# RF RED. F.S EXT.BONNET (BA-102E)
50 - 150 A216-WCB/316+RTFE 150# RF FULL BORE F.S (BA-103) (08-2,09)
200 - 600 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR (BA-108) (08-2,09)
ASME
650 - 1300 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-109)
BUTTERFLY
ASME
(BF-103)
PLUG

2 43/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
Notes :

Threaded joints are permitted only at the outlet of vent and drain valves, hydrostatic connections, outlet instrument take-off valves
03-2
and to match equipment.
05
06 These valves shall be used only for vent, drain and instrument connections. These valves
07 have no flanges but are installed between line flanges with extra-length bolts. Full port valves
08-2 shall be used if indicated on the P&ID.
09
15 These valves shall be used if matching to flanged nozzles.
35 323.2.2 of ASME B31.3.
2 44/334
CLASS: 01CS1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 100010501100115012001300
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S N B B
150 S S S S N N B B
200 S S S S N N N B B
250 S S S S N N N N B B
300 S S S S N N N N N B B
350 S S S S N N N N N N B B
Header Size (DN)
400 S S S S N N N N N N N B B
450 S S S S N N N N N N R R B B
500 S S S S W W W W W W R R R B B
600 S S S S W W W W W W R R R R B B
650 S S S S W W W W W W R R R R R B B
700 S S S S W W W W W W R R R R R R B B
750 S S S S W W W W W W R R R R R R R B B
800 S S S S W W W W W W R R R R R R R R B B
850 S S S S W W W W W W R R R R R R R R R B B
900 S S S S W W W W W W R R R R R R R R R R B B
950 S S S S W W W W W W R R R R R R R R R R R B B
1000 S S S S W W W W W W R R R R R R R R R R R R B B
1050 S S S S W W W W W W R R R R R R R R R R R R R B B
1100 S S S S W W W W W W R R R R R R R R R R R R R R B B
1150 S S S S W W W W W W R R R R R R R R R R R R R R R B B
1200 S S S S W W W W W W R R R R R R R R R R R R R R R R B B
1300 S S S S W W W W W W R R R R R R R R R R R R R R R R R B B
Abbreviation
F Socketweld or Thread Tee B

Buttwelding Tee
S Sockolet or Thredolet
2 45/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01CS1U
RATING ASME 150#
- LICENSOR A CWR,CWS,FW(U/G) PWHT / NACE Not required
- LICENSOR B
PIPE (01,02)
15 - 40 A53-B(ALUMINIZED) SMLS PE SCH80
50 - 150 A53-B(ALUMINIZED) ERW BE STD
200 - 600 A53-B(ALUMINIZED) ERW BE SCH20
650 - 900 A671-CC65-Cl.13(ALUMINIZED) EFW BE STD
950 - 1050 A671-CC65-Cl.13(ALUMINIZED) EFW BE 11.13MM
NIPPLE (02)
15 - 40 A53-B(ALUMINIZED) SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 A53-B(ALUMINIZED) SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A234-WPB(ALUMINIZED) SMLS PBE To match pipe thickness (03-2)
50 - 100 A234-WPB(ALUMINIZED) SMLS BLE/PSE To match pipe thickness (03-2)
15 - 40 A105(ALUMINIZED) SW 3000#
50 - 1800 A234-WPB(ALUMINIZED) WELD BW To match pipe thickness
CAP (02)
15 - 40 A105(ALUMINIZED) NPT 3000#
50 - 1800 A234-WPB(ALUMINIZED) SMLS BW To match pipe thickness
COUPLING (02)
15 - 40 A105(ALUMINIZED) SW 3000#
THREDOLET
15 - 50 A105(ALUMINIZED) THRD 3000#
PLUGS
15 - 50 A105(ALUMINIZED) THRD HEX
FLANGE (02)
15 - 600 A105(ALUMINIZED) 150# SO RF
ASME
650 - 1150 A105(ALUMINIZED) 150# WN RF
B16.47-A
AWWA
1200 - 1800 A105(ALUMINIZED) 150# SO RF
C207 Cl.D
100 - 600 A105(ALUMINIZED) 150# SO RF WITH J.B
WITH J.B
650 - 1150 A105(ALUMINIZED) 150# WN RF ASME
B16.47-A
WITH J.B
1200 - 1800 A105(ALUMINIZED) 150# SO RF AWWA
C207 Cl.D
15 - 600 A105(ALUMINIZED) 150# SO FF (11,14)
ASME
650 - 1150 A105(ALUMINIZED) 150# WN FF (11,14)
B16.47-A
AWWA
1200 - 1800 A105(ALUMINIZED) 150# SO FF (11,14)
C207 Cl.D
15 - 600 A105(ALUMINIZED) 300# SO RF (12,82)
ASME
650 - 1150 A105(ALUMINIZED) 300# WN RF (12,82)
B16.47-A
AWWA
1200 - 1200 A105(ALUMINIZED) 300# SO RF (12,82)
C207 Cl.D
BLIND FLANGE
15 - 600 A105(ALUMINIZED) 150# BLIND RF
ASME
B16.47-A
AWWA
C207 Cl.D
2 46/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A CWR,CWS,FW(U/G) PWHT / NACE Not required
- LICENSOR B
LINE BLANK
15 - 350 A105(ALUMINIZED) 150# FIG-8 FF
400 - 600 A105(ALUMINIZED) 150# BLK&SPC FF
GASKET
15 - 600 COMP.NON-ASBESTOS 150# RF 1.6MM
ASME
B16.47-A
AWWA
C207 Cl.D
15 - 600 COMP.NON-ASBESTOS 150# FF 1.6MM (11,14)
ASME
B16.47-A
AWWA
C207 Cl.D
15 - 600 COMP.NON-ASBESTOS 300# RF 1.6MM (82)
ASME
B16.47-A
AWWA
C207 Cl.D
BOLT/NUT
A193-B7/A194-2H(ALUMINIZED) STUD/H.HEX
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105)
BUTTERFLY
ASME
(BF-107)
Notes :
03-2
09
35
323.2.2 of ASME B31.3.
2 47/334
CLASS: 01CS1U
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 100010501100115012001300140015001600
15 F
20 F F
25 F F F
40 F F F F
50 C C C B B
80 C C C C B B
100 C C C C N B B
150 C C C C N N B B
200 C C C C N N N B B
250 C C C C N N N N B B
300 C C C C N N N N N B B
350 C C C C N N N N N N B B
400 C C C C N N N N N N N B B
450 C C C C N N N N N N N N B B
Header Size (DN)
500 C C C C R R R R R R R R R B B
600 C C C C R R R R R R R R R R B B
650 C C C C R R R R R R R R R R R B B
700 C C C C R R R R R R R R R R R R B B
750 C C C C R R R R R R R R R R R R R B B
800 C C C C R R R R R R R R R R R R R R B B
850 C C C C R R R R R R R R R R R R R R R B B
900 C C C C R R R R R R R R R R R R R R R R B B
950 C C C C R R R R R R R R R R R R R R R R R B B
1000 C C C C R R R R R R R R R R R R R R R R R R B B
1050 C C C C R R R R R R R R R R R R R R R R R R R B B
1100 C C C C R R R R R R R R R R R R R R R R R R R R B B
1150 C C C C R R R R R R R R R R R R R R R R R R R R R B B
1200 C C C C R R R R R R R R R R R R R R R R R R R R R R B B
1300 C C C C R R R R R R R R R R R R R R R R R R R R R R R B B
1400 C C C C R R R R R R R R R R R R R R R R R R R R R R R R B B
1500 C C C C R R R R R R R R R R R R R R R R R R R R R R R R R B B
1600 C C C C R R R R R R R R R R R R R R R R R R R R R R R R R R B B
Abbreviation

Buttwelding Tee
C Half Coupling
2 48/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
TYPICAL SERVICE AC,DRO,FGO,FW,IA,PA,PVS,CWS,CWR,WW,BD,LS,LC DES. PRES.(barg) 19.6 to 5.5
- LICENSOR B
PIPE (01,02)
15 - 20 API5L-B-PSL.1 SMLS PE XXS
1000 - 1000 API5L-B-PSL.1 DSAW BE XS
1150 - 1150 A671-CC65-Cl.22 EFW BE XS
1200 - 1300 A671-CC65-Cl.22 EFW BE 14.27MM
1400 - 1500 A671-CC65-Cl.22 EFW BE 15.88MM
1600 - 1600 A671-CC65-Cl.22 EFW BE 17.48MM
TUBE
10 - 15 B68-C10200 SMLS PE 0.89MM
TUBE TEE/TUBE UNION
10 - 15 BRASS F-FERR 3000#
FEMALE CONNECTOR
10 - 15 BRASS SW / F-FERR 3000#
MALE CONNECTOR
10 - 15 BRASS PE / F-FERR 3000#
NIPPLE (02)
15 - 40 API5L-B-PSL.1 SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 API5L-B-PSL.1 SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A105 SW 3000#
CAP (02)
15 - 40 A105 THRD 3000#
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (02)
15 - 40 A105 THRD HEX (03-2)
WELDOLET (02,05)
2 49/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
FLANGE (02)
15 - 40 A105 150# SW RF
50 - 600 A105 150# SO RF
ASME
650 - 1500 A105 150# WN RF
B16.47-A
AWWA
1600 - 1600 A105 150# WN RF
C207 Cl.D
100 - 600 A105 150# SO RF WITH J.B
WITH J.B
650 - 1500 A105 150# WN RF ASME
B16.47-A
WITH J.B
1600 - 1600 A105 150# WN RF AWWA
C207 Cl.D
15 - 40 A105 150# SW FF (11,14)
50 - 600 A105 150# SO FF (11,14)
15 - 40 A105 300# SW RF (12,82)
50 - 600 A105 300# WN RF (12,82)
15 - 40 A105 600# SW RF (82)
50 - 400 A105 600# WN RF (82)
15 - 40 A105 1500# SW RTJ (82)
50 - 50 A105 1500# WN RTJ (82)
80 - 600 A105 900# WN RTJ (82)
80 - 600 A105 1500# WN RTJ (82)
RED. FLANGE
50 - 600 A105 150# SO RF
BLIND FLANGE
15 - 600 A105 150# BLIND RF
ASME
650 - 1500 A105 150# BLIND RF
B16.47-A
AWWA
1600 - 1600 A105 150# BLIND RF
C207 Cl.D
LINE BLANK
15 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
ASME
650 - 1500 A105 150# BLK&SPC FF
B16.47-A
AWWA
1600 - 1600 A105 150# BLK&SPC FF
C207 Cl.D
GASKET
ASME
B16.47-A
AWWA
C207 Cl.D
BOLT/NUT
2 50/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105)
ASME
(GA-103)
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105A) (08-2)
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101) (15)
GLOBE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GL-101)
BLOW DOWN
15 - 40 A105/13Cr+HF 800# SW BB OS&Y
CHECK
ASME
(CH-103)
AWWA
(62)
C207 Cl.D
1600- 1600 A216-WCB/13Cr+HF 150# RF BC SWING REFERENCE
(CH-103)

ASME
(CH-105)
AWWA
1600 - 1600 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE C207 Cl.D (07,26-2,63)
(CH-105)
2 51/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
BALL
ASME
650 - 1500 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (08-2,09)
(BA-106)
ASME
(BA-109)
15 - 40 A216-WCB/316+HF 300# SW RED. BORE F.S (BA-137) (09)
50 - 150 A216-WCB/316+HF 150# RF RED. BORE F.S (BA-138) (09)
200 - 600 A216-WCB/316+HF 150# RF RED. BORE F.S GEAR (BA-140) (09)
ASME
650 - 1500 A216-WCB/316+HF 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-141)
80 - 150 A216-WCB/316+HF 150# RF FULL BORE F.S (BA-139) (08-2,09)
200 - 600 A216-WCB/316+HF 150# RF FULL BORE F.S GEAR (BA-142) (08-2,09)
ASME
650 - 1500 A216-WCB/316+HF 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-143)
BUTTERFLY
ASME
650 - 1500 A216-WCB/316+RTFE 150# LUG GEAR B16.47-A
(BF-103)
AWWA
1600 - 1600 A216-WCB/316+RTFE 150# LUG GEAR C207 Cl.D
REFERENCE
(BF-103)
80 - 150 A216-WCB/316 150# LUG LEVER (BF-109) (09)
200 - 600 A216-WCB/316 150# LUG GEAR (BF-110) (09)
ASME
650 - 1500 A216-WCB/316 150# LUG GEAR B16.47-A
(BF-111)
PLUG
2 52/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
Notes :
03-2
05
09
35
323.2.2 of ASME B31.3.
2 53/334
CLASS: 01CS2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 100010501100115012001300140015001600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S N B B
150 S S S S N N B B
400 S S S S N R R R R R R B B
450 S S S S N R R R R R R R B B
Header Size (DN)
1400 S S S S W W W W W W R R R R R R R R R R R R R R R R R R B B
1500 S S S S W W W W W W R R R R R R R R R R R R R R R R R R R B B
1600 S S S S W W W W W W R R R R R R R R R R R R R R R R R R R R B B
Abbreviation

Buttwelding Tee
2 54/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
TYPICAL SERVICE SOUR CLOSED DRAIN DES. PRES.(barg) 19.6 to 5.5
- LICENSOR B
PIPE (01,02)
15 - 20 API5L-B-PSL.1 (GALV+PE.C) SMLS PE XXS
25 - 40 API5L-B-PSL.1 (GALV+PE.C) SMLS PE SCH160
50 - 50 API5L-B-PSL.1 (GALV+PE.C) SMLS BE SCH80
450 - 600 API5L-B-PSL.1 (GALV+PE.C) DSAW BE SCH20
650 - 650 API5L-B-PSL.1 (GALV+PE.C) DSAW BE STD
700 - 750 API5L-B-PSL.1 (GALV+PE.C) DSAW BE 10.31MM
1000 - 1000 API5L-B-PSL.1 (GALV+PE.C) DSAW BE XS
1150 - 1150 A671-CC65-Cl.22 (GALV+PE.C) EFW BE XS
1200 - 1300 A671-CC65-Cl.22 (GALV+PE.C) EFW BE 14.27MM
NIPPLE (02)
15 - 40 API5L-B-PSL.1 (GALV) SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 API5L-B-PSL.1 (GALV) SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A234-WPB (GALV) SMLS PBE To match pipe thickness (03-2)
50 - 100 A234-WPB (GALV) SMLS BLE/PSE To match pipe thickness (03-2)
15 - 40 A105 (GALV) SW 3000#
50 - 100 A234-WPB (GALV) SMLS BW To match pipe thickness
150 - 400 A234-WPB (GALV+PE.C) SMLS BW To match pipe thickness
450 - 1100 A234-WPB (GALV+PE.C) WELD BW To match pipe thickness
1150 - 1600 A234-WPB (GALV+PE.C) WELD BW To match pipe thickness RT 100%
LATERAL (02)
50 - 100 A234-WPB (GALV) WELD BW To match pipe thickness
CAP (02)
15 - 40 A105 (GALV) THRD 3000#
50 - 750 A234-WPB (GALV) SMLS BW To match pipe thickness
15 - 40 A105 (GALV) SW 3000#
PLUGS (02)
15 - 40 A105 (GALV) THRD HEX (03-2)
WELDOLET (02,05)
500 - 1600 A105 (GALV) BW To match pipe thickness
2 55/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
FLANGE (02)
15 - 40 A105 (GALV) 150# SW RF
50 - 600 A105 (GALV) 150# SO RF
ASME
650 - 1500 A105 (GALV) 150# WN RF
B16.47-A
AWWA
1600 - 1600 A105 (GALV) 150# WN RF
C207 Cl.D
150 - 600 A105 (GALV) 150# SO RF WITH J.B
WITH J.B
650 - 1500 A105 (GALV) 150# WN RF ASME
B16.47-A
WITH J.B
1600 - 1600 A105 (GALV) 150# WN RF AWWA
C207 Cl.D
15 - 40 A105 (GALV) 150# SW FF (11,14)
50 - 600 A105 (GALV) 150# SO FF (11,14)
15 - 40 A105 (GALV) 300# SW RF (12,82)
50 - 600 A105 (GALV) 300# WN RF (12,82)
15 - 40 A105 (GALV) 600# SW RF (82)
50 - 400 A105 (GALV) 600# WN RF (82)
BLIND FLANGE
15 - 600 A105 (GALV) 150# BLIND RF
ASME
650 - 1500 A105 (GALV) 150# BLIND RF
B16.47-A
AWWA
1600 - 1600 A105 (GALV) 150# BLIND RF
C207 Cl.D
LINE BLANK
15 - 350 A105(GALV) 150# FIG-8 FF
400 - 600 A105(GALV) 150# BLK&SPC FF
ASME
650 - 1500 A105(GALV) 150# BLK&SPC FF
B16.47-A
AWWA
1600 - 1600 A105(GALV) 150# BLK&SPC FF
C207 Cl.D
2 56/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
GASKET
ASME
B16.47-A
AWWA
C207 Cl.D
BOLT/NUT
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105)
ASME
(GA-103)
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101) (15)
GLOBE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GL-101)
BLOW DOWN
15 - 40 A105/13Cr+HF 800# SW BB OS&Y
CHECK
ASME
(CH-103)
AWWA
(62)
C207 Cl.D
1600- 1600 A216-WCB/13Cr+HF 150# RF BC SWING REFERENCE
(CH-103)

ASME
(CH-105)
AWWA
(07,26-2,63)
C207 Cl.D
1600 - 1600 A216-WCB/13Cr+HF 150# WAFER DUAL PLATE REFERENCE
(CH-105)
2 57/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
BALL
ASME
650 - 1500 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (08-2,09)
(BA-106)
ASME
(BA-109)
15 - 40 A216-WCB/316+HF 300# SW RED. BORE F.S (BA-137) (09)
ASME
650 - 1500 A216-WCB/316+HF 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-141)
ASME
650 - 1500 A216-WCB/316+HF 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-143)
BUTTERFLY
ASME
(BF-103)
AWWA
1600 - 1600 A216-WCB/316+RTFE 150# LUG GEAR C207 Cl.D
REFERENCE
(BF-103)
80 - 150 A216-WCB/316 150# LUG LEVER (BF-109) (09)
200 - 600 A216-WCB/316 150# LUG GEAR (BF-110) (09)
ASME
650 - 1500 A216-WCB/316 150# LUG GEAR B16.47-A
(BF-111)
PLUG
2 58/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B
Notes :
03-2
05
09
35
323.2.2 of ASME B31.3.
2 59/334
CLASS: 01CS2U
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 100010501100115012001300140015001600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S N B B
150 S S S S N N B B
400 S S S S N R R R R R R B B
450 S S S S N R R R R R R R B B
Header Size (DN)
1500 S S S S W W W W W W R R R R R R R R R R R R R R R R R R R B B
1600 S S S S W W W W W W R R R R R R R R R R R R R R R R R R R R B B
Abbreviation

Buttwelding Tee
2 60/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A PWHT / NACE PWHT applies
- LICENSOR B AMMONIA STRIPPING,WWS (from NH3 Stripper),PSG, LSS(for Sulphur Pit)
PIPE (01,02,20)
15 - 50 A106-B SMLS BE XXS
80 - 80 A106-B SMLS BE SCH160
100 - 100 A106-B SMLS BE SCH120
150 - 150 A106-B SMLS BE SCH80
200 - 250 A106-B SMLS BE SCH60
300 - 400 A106-B SMLS BE SCH40
450 - 500 A106-B SMLS BE SCH30
600 - 600 A106-B SMLS BE XS
650 - 800 A671-CC65-Cl.22 EFW BE 14.27MM
850 - 900 A671-CC65-Cl.22 EFW BE SCH30
PIPE(For Sulphur Pit)
100 - 100 SA106-B SMLS BE SCH80 (101)
NIPPLE (02)
15 - 40 A106-B SMLS BBE To match pipe thickness L=3" (03-3)
SWAGE (02)
15 - 100 A234-WPB SMLS BBE To match pipe thickness (03-3)
CAP(For Sulphur Pit)
100 - 100 SA234-WPB SMLS BW To match pipe thickness (101)
CAP (02)
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 300# WN RF
50 - 600 A105 150# WN RF
ASME
650 - 900 A105 150# WN RF
B16.47-A
100 - 600 A105 150# WN RF WITH J.B
WITH J.B
650 - 900 A105 150# WN RF ASME
B16.47-A
50 - 600 A105 300# WN RF (12,82)
15 - 600 A105 600# WN RF (82)
15 - 40 A105 300# WN FF (11,14)
50 - 600 A105 150# WN FF (11,14)
ASME
650 - 900 A105 150# WN FF (11,14)
B16.47-A
15 - 600 A105 150# SO RF (50,82)
15 - 600 A105 300# SO RF (12,50,82)
BLIND FLANGE
15 - 40 A105 300# BLIND RF
50 - 600 A105 150# BLIND RF
ASME
650 - 900 A105 150# BLIND RF
B16.47-A
15 - 40 A105 300# BLIND FF (11,14)
50 - 600 A105 150# BLIND FF (11,14)
50 - 600 A105 300# BLIND RF (12,82)
15 - 600 A105 600# BLIND RF (12,82)
2 61/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
LINE BLANK
15 - 40 A105 300# FIG-8 FF
50 - 350 A105 150# FIG-8 FF
400 - 600 A105 150# BLK&SPC FF
ASME
650 - 900 A105 150# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
ASME
B16.47-A
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
BOLT/NUT
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-411) (09)
ASME
(GA-416)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-411) (09)
CHECK
ASME
(CH-413)
50 - 600 A216-WCB/13Cr 150# WAFER DUAL PLATE (CH-414) (07,26-2,63)
ASME
650 - 900 A216-WCB/13Cr 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-415)
BALL
ASME
650 - 900 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (08,09)
(BA-415)
80 - 150 A216-WCB/316+RTFE 150# RF FULL BORE F.S (BA-413) (08,09)
200 - 600 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR (BA-416) (08,09)
ASME
650 - 900 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08,09)
(BA-417)
2 62/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BUTTERFLY
ASME
(BF-413)
PLUG
REFERENCE
15 - 40 A216-WCB/316+PTFE 300# RF REGULAR (09)
(PL-411)
Notes :
03-2
05
08
09
20 Additional reinforcement required for unconnected branches sizes 15nb to 25nb.
35
323.2.2 of ASME B31.3.
50 Flanges to have front and back welds in accordance with fig. 328.5.2B from ASME B31.3
101 This pipe shall be used for sulphur pit risers. And shall get a certification at ASME.
2 63/334
CLASS: 01CS4
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Header Size (DN)
400 W W W W N R R R R R R B B
450 W W W W N R R R R R R R B B
800 W W W W W W W W W W R R R R R R R R B B
850 W W W W W W W W W W R R R R R R R R R B B
900 W W W W W W W W W W R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 64/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01D1
RATING ASME 150#
- LICENSOR B LCD,MCD (Hydrogen content to be considered up to 200 ℃)
PIPE (01,02)
15 - 20 A333-6 SMLS PE SCH160
25 - 40 A333-6 SMLS PE SCH80
50 - 50 A333-6 SMLS BE SCH80
80 - 200 A333-6 SMLS BE SCH40
250 - 600 A333-6 SMLS BE SCH20
IMPACT
650 - 900 A671-CC65-Cl.22 EFW BE STD
TEST
IMPACT
950 - 1000 A671-CC65-Cl.22 EFW BE 10.31MM TEST
IMPACT
IMPACT
IMPACT
1200 - 1200 A671-CC65-Cl.22 EFW BE XS TESTIMP
1300 - 1300 A671-CC65-Cl.22 EFW BE 14.27MM ACT
TEST
IMPACT
NIPPLE (02)
15 - 40 A333-6 SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 A333-6 SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A420-WPL6 SMLS PBE To match pipe thickness (03-2)
50 - 100 A420-WPL6 SMLS BLE/PSE To match pipe thickness (03-2)
15 - 40 A350-LF2-Cl.1 SW 3000#
50 - 600 A420-WPL6 SMLS BW To match pipe thickness
650 - 1400 A420-WPL6 WELD BW To match pipe thickness RT 100%
CAP (02)
15 - 40 A350-LF2-Cl.1 THRD 3000#
15 - 40 A350-LF2-Cl.1 SW 3000#
THREDOLET (163)
15 - 40 A350-LF2-Cl.1 THRD 3000#
PLUGS (02)
15 - 40 A350-LF2-Cl.1 THRD HEX (03-2)
WELDOLET (02,05)
50 - 1400 A350-LF2-Cl.1 BW To match pipe thickness
FLANGE (02)
15 - 40 A350-LF2-Cl.1 300# SW RF
50 - 600 A350-LF2-Cl.1 150# WN RF (13)
ASME
650 - 1400 A350-LF2-Cl.1 150# WN RF (13)
B16.47-A
100 - 600 A350-LF2-Cl.1 150# WN RF WITH J.B (13)
WITH J.B
650 - 1400 A350-LF2-Cl.1 150# WN RF ASME (13)
B16.47-A
15 - 40 A350-LF2-Cl.1 300# SW FF (11,14)
50 - 600 A350-LF2-Cl.1 150# WN FF (11,13,14)
ASME (11,13,14)
650 - 1400 A350-LF2-Cl.1 150# WN FF
B16.47-A
50 - 600 A350-LF2-Cl.1 300# WN RF (12,13)
2 65/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BLIND FLANGE
15 - 40 A350-LF2-Cl.1 300# BLIND RF
50 - 600 A350-LF2-Cl.1 150# BLIND RF
ASME
650 - 1400 A350-LF2-Cl.1 150# BLIND RF
B16.47-A
ASME
650 - 1400 A350-LF2-Cl.1 150# BLIND FF
B16.47-A
50 - 600 A350-LF2-Cl.1 300# BLIND RF (12)
ASME
650 - 1400 A350-LF2-Cl.1 300# BLIND RF (12)
B16.47-A
LINE BLANK
15 - 40 A350-LF2-Cl.1 300# FIG-8 FF
50 - 350 A350-LF2-Cl.1 150# FIG-8 FF
400 - 600 A350-LF2-Cl.1 150# BLK&SPC FF
ASME
650 - 1400 A350-LF2-Cl.1 150# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
ASME
B16.47-A
15 - 600 SW(316+GRAP)IO:316 300# RF 4.5MM
BOLT/NUT
GATE
15 - 40 A350-LF2-Cl.1/316+HF 800# SW BB OS&Y (GA-402)
50 - 300 A352-LCB/316+HF 150# RF BB OS&Y (GA-404)
350 - 600 A352-LCB/316+HF 150# RF BB OS&Y GEAR (GA-405)
ASME
650 - 1400 A352-LCB/316+HF 150# RF BB OS&Y GEAR B16.47-A
(GA-406)
15 - 40 A350-LF2-Cl.1/316+HF 300# RF BB OS&Y (GA-401) (15)
GLOBE
15 - 40 A350-LF2-Cl.1/316+HF 800# SW BB OS&Y (GL-401)
50 - 200 A352-LCB/316+HF 150# RF BB OS&Y (GL-402)
250 - 300 A352-LCB/316+HF 150# RF BB OS&Y GEAR (GL-403)
CHECK
15 - 40 A350-LF2-Cl.1/316+HF 800# SW BC LIFT (CH-401)
50 - 600 A352-LCB/316+HF 150# RF BC SWING (CH-402)
ASME
650 - 1400 A352-LCB/316+HF 150# RF BC SWING B16.47-A
(CH-403)
80 - 600 A352-LCB/316+HF 150# WAFER DUAL PLATE (CH-404)
ASME
650 - 1400 A352-LCB/316+HF 150# WAFER DUAL PLATE B16.47-A
(CH-405)
2 66/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BALL
15 - 40 A352-LCB/316+RTFE 300# RF RED. BORE F.S (BA-401) (09)
200 - 600 A352-LCB/316+RTFE 150# RF RED. BORE F.S GEAR (BA-404) (09)
ASME
650 - 1400 A352-LCB/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-406)
80 - 150 A352-LCB/316+RTFE 150# RF FULL BORE F.S (BA-403) (08-2,09)
200 - 600 A352-LCB/316+RTFE 150# RF FULL BORE F.S GEAR (BA-405) (08-2,09)
ASME
650 - 1400 A352-LCB/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-407)
BUTTERFLY
80 - 150 A352-LCB/316+RTFE 150# LUG LEVER (BF-401) (09)
200 - 600 A352-LCB/316+RTFE 150# LUG GEAR (BF-402) (09)
PLUG
15 - 40 A352-LCB/316+PTFE 300# RF REGULAR (PL-404) (09)
200 - 450 A352-LCB/316+PTFE 150# RF REGULAR GEAR (PL-403) (09)
Notes :
03-2
05
08-2 Full port valves shall be used if indicated on the P&ID.
09
13 Weld-neck flanges shall be used against butt-weld fittings. Otherwise slip-on flanges shall be used.
35
323.2.2 of ASME B31.3.
2 67/334
CLASS: 01D1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000105011001150120013001400
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S N B B
150 S S S S N N B B
400 S S S S N N N N N N N B B
Header Size (DN)
450 S S S S N N N N N N R R B B
Abbreviation

Buttwelding Tee
2 68/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A PWHT / NACE PWHT and NACE apply
- LICENSOR B RECT,PSOG,SGT
PIPE (01,02)
15 - 20 A333-6(NACE) SMLS BE XXS
25 - 40 A333-6(NACE) SMLS BE SCH160
250 - 600 A333-6(NACE) SMLS BE SCH20
IMPACT
650 - 800 A671-CC65-Cl.22(NACE) EFW BE STD
TEST
IMPACT
850 - 850 A671-CC65-Cl.22(NACE) EFW BE 10.31MM TEST
IMPACT
IMPACT
IMPACT
1100 - 1150 A671-CC65-Cl.22(NACE) EFW BE XS TESTIMP
1200 - 1200 A671-CC65-Cl.22(NACE) EFW BE 14.27MM ACT
TEST
NIPPLE (02)
15 - 40 A333-6(NACE) SMLS BBE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 100 A420-WPL6(NACE) SMLS BBE To match pipe thickness (03-2)
15 - 600 A420-WPL6(NACE) SMLS BW To match pipe thickness
650 - 1200 A420-WPL6(NACE) WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 40 A350-LF2-Cl.1(NACE) THRD 3000#
PLUGS (163)
15 - 40 A350-LF2-Cl.1(NACE) THRD HEX
CAP (02)
WELDOLET (02,05)
80 - 1200 A350-LF2-Cl.1(NACE) BW To match pipe thickness
2 69/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
FLANGE (02)
15 - 40 A350-LF2-Cl.1(NACE) 300# WN RF (13)
50 - 600 A350-LF2-Cl.1(NACE) 150# WN RF (13)
ASME
650 - 1200 A350-LF2-Cl.1(NACE) 150# WN RF (13)
B16.47-A
100 - 600 A350-LF2-Cl.1(NACE) 150# WN RF WITH J.B (13)
WITH J.B
650 - 1200 A350-LF2-Cl.1(NACE) 150# WN RF ASME (13)
B16.47-A
15 - 40 A350-LF2-Cl.1(NACE) 300# WN FF (11,13,14)
50 - 600 A350-LF2-Cl.1(NACE) 150# WN FF (11,13,14)
ASME
650 - 1200 A350-LF2-Cl.1(NACE) 150# WN FF (11,13,14)
B16.47-A
50 - 600 A350-LF2-Cl.1(NACE) 300# WN RF (12,13)
ASME
650 - 1200 A350-LF2-Cl.1(NACE) 300# WN RF (12,13)
B16.47-A
BLIND FLANGE
15 - 40 A350-LF2-Cl.1(NACE) 300# BLIND RF
ASME
B16.47-A
ASME
650 - 1200 A350-LF2-Cl.1(NACE) 150# BLIND FF
B16.47-A
50 - 600 A350-LF2-Cl.1(NACE) 300# BLIND RF (12)
ASME
B16.47-A
LINE BLANK
15 - 40 A350-LF2-Cl.1(NACE) 300# FIG-8 FF
50 - 350 A350-LF2-Cl.1(NACE) 150# FIG-8 FF
400 - 600 A350-LF2-Cl.1(NACE) 150# BLK&SPC FF
ASME
B16.47-A
GASKET
15 - 40 FLEX.GRAPH.+304SS 300# RF 1.6MM (NACE)
(NACE)
650 - 1200 FLEX.GRAPH.+304SS 150# RF 1.6MM ASME
B16.47-A
15 - 40 FLEX.GRAPH.+304SS 300# FF 1.6MM (NACE) (11,14)
(NACE)
650 - 1200 FLEX.GRAPH.+304SS 150# FF 1.6MM ASME (11,14)
B16.47-A
(NACE)
B16.47-A
(NACE)
650 - 1200 SW(316+GRAP)IO:316 300# RF 4.5MM ASME
B16.47-A
BOLT/NUT
A193-B7M/A194-2HM(Zn-CHROMATE) STUD/H.HEX
2 70/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
GATE
15 - 40 A350-LF2-Cl.1(NACE)/316 300# RF BB OS&Y B.S (GA-420) (09)
50 - 80 A352-LCB(NACE)/316 150# RF BB OS&Y B.S (GA-421) (08-2,09)
BB OS&Y SPRING
100 - 300 A352-LCB(NACE)/316 150# RF (GA-421) (08-2,09)
LOADED
350 - 600 A352-LCB(NACE)/316 150# RF BB OS&Y SP.L GEAR (GA-422) (08-2,09)
ASME
650 - 1200 A352-LCB(NACE)/316 150# RF BB OS&Y SP.L GEAR B16.47-A (08-2,09)
(GA-423)
GLOBE
15 - 40 A350-LF2-Cl.1(NACE)/316 300# RF BB OS&Y B.S (GL-420) (09)
50 - 80 A352-LCB(NACE)/316 150# RF BB OS&Y (GL-421) (09)
100 - 200 A352-LCB(NACE)/316 150# RF BB OS&Y (GL-421) (09)
SPRING LOADED
250 - 300 A352-LCB(NACE)/316 150# RF BB OS&Y SP.L GEAR (GL-422) (09)
CHECK
15 - 40 A350-LF2-Cl.1(NACE)/316 300# RF BC LIFT (CH-420) (61)
50 - 600 A352-LCB(NACE)/316 150# RF BC SWING (CH-421) (62)
ASME
650 - 1200 A352-LCB(NACE)/316 150# RF BC SWING B16.47-A (62)
(CH-422)
80 - 600 A352-LCB(NACE)/316 150# WAFER DUAL PLATE (CH-423) (07,26-2,63)
ASME
650 - 1200 A352-LCB(NACE)/316 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-424)
BALL
15 - 40 A352-LCB(NACE)/316 300# RF RED. BORE F.S (BA-419) (09)
50 - 150 A352-LCB(NACE)/316 150# RF RED. BORE F.S (BA-420) (09)
200 - 600 A352-LCB(NACE)/316 150# RF RED. BORE F.S GEAR (BA-422) (09)
ASME
650 - 1200 A352-LCB(NACE)/316 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-424)
80 - 150 A352-LCB(NACE)/316 150# RF FULL BORE F.S (BA-421) (08-2,09)
200 - 600 A352-LCB(NACE)/316 150# RF FULL BORE F.S GEAR (BA-423) (08-2,09)
ASME
650 - 1200 A352-LCB(NACE)/316 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-425)
BUTTERFLY
80 - 150 A352-LCB(NACE)/316 150# LUG LEVER (BF-420) (09)
200 - 600 A352-LCB(NACE)/316 150# LUG GEAR (BF-421) (09)
650 - 1200 A352-LCB(NACE)/316 150# LUG GEAR (BF-422)
PLUG
15 - 40 A352-LCB(NACE)/316+PTFE 300# RF REGULAR (PL-420) (09)
200 - 450 A352-LCB(NACE)/316+PTFE 150# RF REGULAR GEAR (PL-422) (09)
2 71/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
Note :
- Material selection in compliance with licensor B standard LS 129-37 for Rectisol.
03-2
05
09
35
323.2.2 of ASME B31.3.
62 These check valves shall be installed in a horizontal position with cover up or in a vertical position with upward flow. These
63 check valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow. These
163 items shall be used only for hydrotest vent/drain.
2 72/334
CLASS: 01D2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 10001050110011501200
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Header Size (DN)
950 W W W W W W W W W W R R R R R R R R R R R B B
1000 W W W W W W W W W W R R R R R R R R R R R R B B
1050 W W W W W W W W W W R R R R R R R R R R R R R B B
1100 W W W W W W W W W W R R R R R R R R R R R R R R B B
1150 W W W W W W W W W W R R R R R R R R R R R R R R R B B
1200 W W W W W W W W W W R R R R R R R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 73/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01FG0
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) 0 to 93
TYPICAL SERVICE DES. PRES.(barg) 10.3
- LICENSOR A PWHT / NACE Not applicable
- LICENSOR B HYDROGEN CLORIDE
PIPE
15 - 200 D2996-RTRP PE MFR P=10kg/cm2
ELBOW/REDUCER/TEE
15 - 200 D5685-RTRP PE MFR P=10kg/cm2
FLANGE
15 - 200 D4024-RTR 150# WN FF
15 - 200 D4024-RTR 300# WN FF (82)
BLIND FLANGE
15 - 200 D4024-RTR 150# BLIND FF
GASKET
150# FF 1.6MM 50-60
A SHORE
DUROMETER
15 - 200 ELASTOMERIC
BOLT/NUT
BALL
25 - 150 A395/DI(PFA.L) 150# FF RED. BORE F.S (BA-950)
PLUG
25 - 150 A395/DI(PFA.L) 150# FF REGULAR (PL-950)
CHECK
25 - 200 A395/DI(PFA.L) 150# FF BC SWING (CH-955) (62)
BUTTERFLY
Notes :
2 74/334
CLASS: 01FG0
Branch Size (DN)

15 20 25 40 50 80 100 150 200
15 B
20 B B
Header Size (DN)
25 B B B
40 B B B B
50 B B B B B
80 B B B B B B
100 B B B B B B B
150 B B B B B B B B
200 B B B B B B B B B
Abbreviation
B Buttwelding Tee
2 75/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01G1
RATING ASME 150#
- LICENSOR A PWHT / NACE Required on all Butt Welds
- LICENSOR B PCA (Flanged guards required)
PIPE (01,02)
15 - 20 A106-B SMLS BE SCH160
25 - 50 A106-B SMLS BE SCH80
80 - 200 A106-B SMLS BE SCH40
250 - 300 A106-B SMLS BE SCH20
NIPPLE (02)
15 - 40 A106-B SMLS BBE To match pipe thickness L=3" (03-3)
SWAGE (02)
15 - 100 A234-WPB SMLS BBE To match pipe thickness (03-3)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
CAP (02)
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 300# WN RF (13)
50 - 300 A105 150# WN RF (13)
100 - 300 A105 150# WN RF WITH J.B (13)
15 - 40 A105 300# WN FF (11,13,14)
50 - 300 A105 150# WN FF (11,13,14)
50 - 300 A105 300# SO RF (12,50)
50 - 300 A105 300# WN RF (12,13)
BLIND FLANGE
15 - 40 A105 300# BLIND RF
50 - 300 A105 150# BLIND RF
50 - 300 A105 300# BLIND RF (12)
LINE BLANK
15 - 40 A105 300# FIG-8 FF
50 - 300 A105 150# FIG-8 FF
GASKET
BOLT/NUT
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09)
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y (GA-102) (08-2,09)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-119) (09)
CHECK
50 - 300 A216-WCB/13Cr 150# WAFER DUAL PLATE (CH-104) (07,26-2,63)
2 76/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A PWHT / NACE Required on all Butt Welds
- LICENSOR B PCA (Flanged guards required)
Notes :
03-3 Socket Weld and threaded joints are not permitted.
05
09
2 77/334
CLASS: 01G1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Abbreviation
B Buttwelding Tee
2 78/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B PCA,SGT,PSOG
PIPE (01,02)
15 - 20 A106-B(NACE) SMLS BE SCH160
750 - 800 A671-CC65-Cl.22(NACE) EFW BE 10.31MM
NIPPLE (02)
15 - 40 A106-B(NACE) SMLS BBE To match pipe thickness L=3" (03-3)
15 - 40 A106-B(NACE) SMLS BOE/TOE To match pipe thickness L=3"
SWAGE (02)
15 - 100 A234-WPB(NACE) SMLS BBE To match pipe thickness (03-3)
ELBOW/TEE/REDUCER/LATERAL (02)
15 - 600 A234-WPB(NACE) SMLS BW To match pipe thickness
700 - 1100 A234-WPB(NACE) WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 40 A105(NACE) THRD 3000#
PLUGS (163)
15 - 40 A105(NACE) THRD HEX
CAP (02)
WELDOLET (02,05)
50 - 1100 A105(NACE) BW To match pipe thickness
FLANGE (02)
15 - 40 A105(NACE) 300# SO RF (50)
50 - 600 A105(NACE) 150# SO RF (50)
ASME
650 - 1100 A105(NACE) 150# WN RF
B16.47-A
150 - 600 A105(NACE) 150# WN RF
100 - 600 A105(NACE) 150# SO RF WITH J.B
WITH J.B
650 - 1100 A105(NACE) 150# WN RF ASME
B16.47-A
15 - 40 A105(NACE) 300# SO FF (11,14)
50 - 600 A105(NACE) 150# SO FF (11,14)
50 - 600 A105(NACE) 300# WN RF (12)
15 - 600 A105(NACE) 600# WN RF (82)
ASME
800 - 800 A105(NACE) 600# WN RF (82)
B16.47-A
15 - 50 A105(NACE) 1500# WN RF
80 - 400 A105(NACE) 900# WN RTJ
25 - 50 A105(NACE) 1500# WN RTJ
BLIND FLANGE
15 - 40 A105(NACE) 300# BLIND RF
50 - 600 A105(NACE) 150# BLIND RF
ASME
650 - 800 A105(NACE) 150# BLIND RF
B16.47-A
LINE BLANK
15 - 40 A105(NACE) 300# FIG-8 FF
50 - 150 A105(NACE) 150# FIG-8 FF
ASME
850 - 1100 A105(NACE) 150# BLK&SPC FF
B16.47-A
2 79/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
GASKET
(NACE)
B16.47-A
BOLT/NUT
GATE
15 - 40 A105(NACE)/13Cr+HF 300# RF BB OS&Y B.S (GA-426) (09)
50 - 80 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y B.S (GA-427) (08-2,09)
100 - 300 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SPRING LOADED (GA-427) (08-2,09)
350 - 600 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR (GA-428) (08-2,09)
ASME
650 - 1000 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR B16.47-A (08-2,09)
(GA-429)
15 - 40 A105(NACE)/13Cr+HF 300# RF BB OS&Y B.S (GA-426A)
GLOBE
15 - 40 A105(NACE)/13Cr+HF 300# RF BB OS&Y B.S (GL-426) (09)
50 - 80 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y B.S (GL-427) (09)
100 - 200 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SPRING LOADED (GL-427) (09)
250 - 300 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR (GL-428) (09)
CHECK
15 - 40 A105(NACE)/13Cr+HF 300# RF BC LIFT (CH-426) (61)
50 - 600 A216-WCB(NACE)/13Cr+HF 150# RF BC SWING (CH-427) (62)
ASME
650 - 1000 A216-WCB(NACE)/13Cr+HF 150# RF BC SWING B16.47-A (62)
(CH-428)
50 - 600 A216-WCB(NACE)/13Cr 150# WAFER DUAL PLATE (CH-429) (07,26-2,63)
ASME
650 - 1000 A216-WCB(NACE)/13Cr 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-430)
BUTTERFLY
80 - 150 A216-WCB(NACE)/316+RTFE 150# LUG LEVER (BF-426) (09)
200 - 600 A216-WCB(NACE)/316+RTFE 150# LUG GEAR (BF-427) (09)
ASME
650 - 1400 A216-WCB(NACE)/316+RTFE 150# LUG GEAR B16.47-A
(BF-428)
80 - 150 A216-WCB(NACE)/316+HF 150# LUG LEVER (BF-433) (09)
200 - 600 A216-WCB(NACE)/316+HF 150# LUG GEAR (BF-434) (09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# LUG GEAR B16.47-A
(BF-435)
2 80/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BALL
15 - 40 A216-WCB(NACE)/316+RTFE 300# RF RED. BORE F.S (BA-426) (09)
200 - 600 A216-WCB(NACE)/316+RTFE 150# RF RED. BORE F.S GEAR (BA-429) (09)
ASME
650 - 900 A216-WCB(NACE)/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-431)
15 - 40 A216-WCB(NACE)/316+RTFE 300# RF RED. F.S EXT.BONNET (BA-426E)
15 - 40 A216-WCB(NACE)/316+RTFE 300# RF FULL BORE F.S (BA-428A)
80 - 150 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S (BA-428) (08-2,09)
200 - 600 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S GEAR (BA-430) (08-2,09)
ASME
650 - 900 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-432)
15 - 40 A216-WCB(NACE)/316+HF 300# RF RED. BORE F.S (BA-433) (09)
200 - 600 A216-WCB(NACE)/316+HF 150# RF RED. BORE F.S GEAR (BA-436) (09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-438)
80 - 150 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S (BA-435) (08-2,09)
200 - 600 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S GEAR (BA-437) (08-2,09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-439)
3-WAY
40 - 40 A216-WCB(NACE)/316+RTFE 300# RF RED. BORE F.S REFERENCE
(BA-426)
Notes :
05
09
2 81/334
CLASS: 01G2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 700 750 850 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Header Size (DN)
300 W W W W W W W R R B B
350 W W W W W W W R R R B B
400 W W W W W W W R R R R B B
450 W W W W W W W W R R R R B B
700 W W W W W W W W W R R R R R R B B
750 W W W W W W W W W R R R R R R R B B
850 W W W W W W W W W R R R R R R R R R B
900 W W W W W W W W W R R R R R R R R R R B
Abbreviation
B Buttwelding Tee
2 82/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01G2B
RATING ASME 150#
PIPE (01,02)
15 - 20 A106-B(NACE) SMLS BE XXS
NIPPLE (02)
15 - 40 A106-B(NACE) SMLS BBE To match pipe thickness L=3" (03-3)
SWAGE (02)
15 - 100 A234-WPB(NACE) SMLS BBE To match pipe thickness (03-3)
ELBOW/TEE/REDUCER/LATERAL (02)
650 - 1000 A234-WPB(NACE) WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 50 A105(NACE) THRD 3000#
PLUGS (163)
CAP (02)
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105(NACE) 300# SO RF (50)
50 - 600 A105(NACE) 150# SO RF (50)
ASME
650 - 1000 A105(NACE) 150# WN RF
B16.47-A
WITH J.B
650 - 1000 A105(NACE) 150# WN RF ASME
B16.47-A
15 - 40 A105(NACE) 300# SO FF (11,14)
50 - 600 A105(NACE) 150# SO FF (11,14)
ASME
650 - 1000 A105(NACE) 150# WN FF (11,14)
B16.47-A
50 - 600 A105(NACE) 300# WN RF (12)
15 - 600 A105(NACE) 600# WN RF (82)
BLIND FLANGE
15 - 40 A105(NACE) 300# BLIND RF
50 - 600 A105(NACE) 150# BLIND RF
ASME
650 - 1000 A105(NACE) 150# BLIND RF
B16.47-A
LINE BLANK
15 - 40 A105(NACE) 300# FIG-8 FF
50 - 350 A105(NACE) 150# FIG-8 FF
400 - 600 A105(NACE) 150# BLK&SPC FF
ASME
650 - 1000 A105(NACE) 150# BLK&SPC FF
B16.47-A
2 83/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
GASKET
(NACE)
B16.47-A
(NACE)
650 - 1000 FLEX.GRAPH.+304SS 150# FF 1.6MM ASME (11,14)
B16.47-A
50 - 600 FLEX.GRAPH.+304SS 300# RF 1.6MM (NACE) (82)
BOLT/NUT
GATE
15 - 40 A105(NACE)/13Cr+HF 300# RF BB OS&Y B.S (GA-426) (09)
50 - 80 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y B.S (GA-427) (08-2,09)
100 - 300 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SPRING LOADED (GA-427) (08-2,09)
350 - 600 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR (GA-428) (08-2,09)
ASME
650 - 1000 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR B16.47-A (08-2,09)
(GA-429)
GLOBE
15 - 40 A105(NACE)/13Cr+HF 300# RF BB OS&Y B.S (GL-426) (09)
50 - 80 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y B.S (GL-427) (09)
100 - 200 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SPRING LOADED (GL-427) (09)
250 - 300 A216-WCB(NACE)/13Cr+HF 150# RF BB OS&Y SP.L GEAR (GL-428) (09)
CHECK
15 - 40 A105(NACE)/13Cr+HF 300# RF BC LIFT (CH-426) (61)
50 - 600 A216-WCB(NACE)/13Cr+HF 150# RF BC SWING (CH-427) (62)
ASME
650 - 1000 A216-WCB(NACE)/13Cr+HF 150# RF BC SWING B16.47-A (62)
(CH-428)
50 - 600 A216-WCB(NACE)/13Cr 150# WAFER DUAL PLATE (CH-429) (07,26-2,63)
ASME
650 - 1000 A216-WCB(NACE)/13Cr 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-430)
BUTTERFLY
80 - 150 A216-WCB(NACE)/316+RTFE 150# LUG LEVER (BF-426) (09)
200 - 600 A216-WCB(NACE)/316+RTFE 150# LUG GEAR (BF-427) (09)
ASME
650 - 1400 A216-WCB(NACE)/316+RTFE 150# LUG GEAR B16.47-A
(BF-428)
80 - 150 A216-WCB(NACE)/316+HF 150# LUG LEVER (BF-433) (09)
200 - 600 A216-WCB(NACE)/316+HF 150# LUG GEAR (BF-434) (09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# LUG GEAR B16.47-A
(BF-435)
2 84/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BALL
200 - 600 A216-WCB(NACE)/316+RTFE 150# RF RED. BORE F.S GEAR (BA-429) (09)
ASME
650 - 900 A216-WCB(NACE)/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-431)
80 - 150 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S (BA-428) (08-2,09)
200 - 600 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S GEAR (BA-430) (08-2,09)
ASME
650 - 900 A216-WCB(NACE)/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-432)
200 - 600 A216-WCB(NACE)/316+HF 150# RF RED. BORE F.S GEAR (BA-436) (09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-438)
80 - 150 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S (BA-435) (08-2,09)
200 - 600 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S GEAR (BA-437) (08-2,09)
ASME
650 - 900 A216-WCB(NACE)/316+HF 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-439)
3-WAY
40 - 40 A216-WCB(NACE)/316+RTFE 300# RF RED. BORE F.S REFERENCE
(BA-426)
Notes :
05
09
2 85/334
CLASS: 01G2B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Header Size (DN)
950 W W W W W W W W W W R R R R R R R R R R R B B
1000 W W W W W W W W W W R R R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 86/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01GA0
RATING ASME 150#
- LICENSOR A WDR,IA PWHT / NACE Not required
- LICENSOR B
PIPE (01,02,04)
15 - 40 A53-B(GALV) SMLS TE SCH80
50 - 50 A53-B(GALV) SMLS BE SCH80
80 - 300 A53-B(GALV) SMLS BE SCH40
NIPPLE (04)
15 - 40 A53-B(GALV) SMLS TBE To match pipe thickness L=3"
SWAGE (04)
15 - 40 A234-WPB(GALV) SMLS TBE To match pipe thickness
50 - 100 A234-WPB(GALV) SMLS BLE/TSE To match pipe thickness
15 - 40 A105(GALV) THRD 3000#
50 - 300 A234-WPB(GALV) SMLS BW To match pipe thickness
CAP (04)
15 - 40 A105(GALV) THRD 3000#
WELDOLET (02,04,05)
80 - 300 A105(GALV) BW To match pipe thickness
THREDOLET/FULL COUPLING
15 - 40 A105(GALV) THRD 3000#
UNION (04)
15 - 40 A105(GALV) THRD 3000#
PLUGS (04)
15 - 40 A105(GALV) THRD HEX
FLANGE (02)
15 - 40 A105(GALV) 300# NPT RF (12)
50 - 300 A105(GALV) 150# SO RF (50)
100 - 300 A105(GALV) 150# SO RF WITH J.B
100 - 300 A105(GALV) 150# WN FF (11,13,14)
50 - 300 A105(GALV) 300# SO RF (12,50)
100 - 300 A105(GALV) 150# WN RF (13)
100 - 300 A105(GALV) 300# WN RF (12,13)
RED. FLANGE
50 - 300 A105(GALV) 150# SO RF (50)
BLIND FLANGE
15 - 40 A105(GALV) 300# BLIND RF
50 - 300 A105(GALV) 150# BLIND RF
100 - 300 A105(GALV) 300# BLIND RF (12)
GASKET
15 - 40 PTFE+316L 300# RF 1.6MM
50 - 300 PTFE+316L 150# RF 1.6MM
15 - 40 PTFE+316L 300# FF 1.6MM (11,14)
50 - 300 PTFE+316L 150# FF 1.6MM (11,14)
50 - 300 PTFE+316L 300# RF 1.6MM (82)
BOLT/NUT
2 87/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01GA0
RATING ASME 150#
- LICENSOR A WDR,IA PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 B61-C92200/BRONZE 300# NPT UB ISRS (GA-901) (09)
GLOBE
15 - 40 B61-C92200/BRONZE 300# NPT UB ISRS (GL-901) (09)
CHECK
15 - 40 B61-C92200/BRONZE 300# NPT UC LIFT (CH-901) (61)
50 - 300 A126-B/BRONZE 150# WAFER DUAL PLATE (CH-902) (07,26-2,63)
BUTTERFLY
BALL
15 - 40 B61-C92200/316+PTFE 300# NPT RED. BORE F.S (BA-901) (09)
Notes :
04 Sizes 15 to 80 nb are to be pre-galv screwd, 100 nb and above to be Hot Dipped galvanised butt welded spools. Integrally reinforced
branch connections outside the sizes shown in the branch connection table are permitted. Weld thickness of integrally reinforced
05 branch connections shall be checked to determine if PWHT is required.
09
35
323.2.2 of ASME B31.3.
2 88/334
CLASS: 01GA0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 F
20 F F
25 F F F
Header Size (DN)
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S W B B
150 S S S S W W B B
200 S S S S W W W B B
250 S S S S W W W W B B
300 S S S S W W W W W B B
Abbreviation

Buttwelding Tee
2 89/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01GB0
RATING ASME 150#
TYPICAL SERVICE FW(A/G) DES. PRES.(barg) 10.4
- LICENSOR B
PIPE (01,02,04)
15 - 40 A53-B(GALV) SMLS TE SCH80
50 - 300 A53-B(GALV) ERW BE STD
NIPPLE (04)
15 - 40 A53-B(GALV) SMLS TBE To match pipe thickness L=3"
SWAGE (04)
50 - 100 A234-WPB(GALV) SMLS BLE/TSE To match pipe thickness
15 - 40 A105(GALV) THRD 3000#
50 - 300 A234-WPB(GALV) WELD BW To match pipe thickness
CAP (04)
15 - 40 A105(GALV) THRD 3000#
THREDOLET
15 - 40 A105(GALV) THRD 3000#
PLUGS
15 - 50 A105(GALV) THRD HEX
UNION/FULL COUPLING (04)
15 - 40 A105(GALV) THRD 3000#
RED. COUPLING
15 - 40 A105(GALV) THRD 3000#
FLANGE (02)
15 - 40 A105(GALV) 300# NPT RF (12)
50 - 300 A105(GALV) 150# SO RF (50)
100 - 300 A105(GALV) 150# SO RF WITH J.B
100 - 300 A105(GALV) 150# WN FF (11,13,14)
100 - 300 A105(GALV) 300# SO RF (12,50)
100 - 300 A105(GALV) 300# WN RF (12,13)
BLIND FLANGE
15 - 40 A105(GALV) 300# BLIND RF
50 - 300 A105(GALV) 150# BLIND RF
50 - 300 A105(GALV) 300# BLIND RF (12)
LINE BLANK
15 - 40 A105(GALV) 300# FIG-8 FF
50 - 300 A105(GALV) 150# FIG-8 FF
GASKET
15 - 40 PTFE+316L SS 300# RF 1.6MM
50 - 300 PTFE+316L SS 150# RF 1.6MM
100 - 300 PTFE+316L SS 150# FF 1.6MM (11,14)
100 - 300 PTFE+316L SS 300# RF 1.6MM (82)
BOLT/NUT
GATE
15 - 40 B61-C92200/BRONZE 300# NPT UB ISRS (GA-901) (09)
GLOBE
15 - 40 B61-C92200/BRONZE 300# NPT UB ISRS (GL-901) (09)
2 90/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01GB0
RATING ASME 150#
TYPICAL SERVICE FW(A/G) DES. PRES.(barg) 10.4
- LICENSOR B
CHECK
15 - 40 B61-C92200/BRONZE 300# NPT UC LIFT (CH-901) (61)
50 - 300 A126-B/BRONZE 150# WAFER DUAL PLATE (CH-902) (07,26-2,63)
BUTTERFLY
BALL
15 - 40 B61-C92200/316+PTFE 300# NPT RED. BORE F.S (BA-901) (09)
Notes :
04 Sizes 15 to 80 nb are to be pre-galv screwd, 100 nb and above to be Hot Dipped galvanised butt welded spools.
09
2 91/334
CLASS: 01GB0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 F
20 F F
25 F F F
Header Size (DN)
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S N B B
150 S S S S N N B B
Abbreviation

Buttwelding Tee
2 92/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01K2
RATING ASME 150#
- LICENSOR A SLU,LN(Special Area),AV,TV PWHT / NACE Not required
- LICENSOR B
PIPE (01,110)
15 - 20 A312-TP304/304L SMLS BE XXS
25 - 50 A312-TP304/304L SMLS BE SCH160
80 - 300 A312-TP304/304L SMLS BE SCH80S
BASALT LINING
300 - 300 A312-TP304/304L SMLS BE SCH80S OF 200 ID
(109)
BEND (02,113,114)
80 - 300 A312-TP304/304L SMLS BE SCH160 3D (110,111)
80 - 300 A312-TP304/304L SMLS BE SCH160 5D (110,111)
3D
300 - 300 A312-TP304/304L SMLS BE SCH160 BASALT LINING (109,110,111)
OF 200 ID
5D
300 - 300 A312-TP304/304L SMLS BE SCH160 BASALT LINING (109,110,111)
OF 200 ID
NIPPLE (02,113,114)
15 - 40 A312-TP304/304L SMLS BBE To match pipe thickness L=3" (114)
SWAGE (02,113,114)
15 - 50 A403-WP304/304L SMLS BBE To match pipe thickness (114)
80 - 100 A403-WP304/304L SMLS BLE/PSE To match pipe thickness (114)
ELBOW/TEE/REDUCER (02,113,114)
300 - 300 A403-WP304/304L SMLS BW To match pipe thickness BASALT LINING (109)
OF 200 ID
CAP (02,113,114)
LATERAL (02,113,114)
LATROLET (02,113,114)
WELDOLET (02,113,114)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
STUB-END (02,113,114)
SHORT
PATTERN
FLANGEOLET
15 - 80 A182-F304/304L 300# RF XS
FLANGE (02)
15 - 300 A105(GALV) 150# LJ
100 - 300 A105(GALV) 150# LJ WITH J.B
15 - 300 A182-F304/304L 150# WN RF
15 - 300 A182-F304/304L 150# WN FF (11,14)
REDUCING FLANGE (02)
80 - 300 A182-F304/304L 150# WN RF
BLIND FLANGE
15 - 300 A182-F304/304L 150# BLIND RF
15 - 50 A182-F304/304L 150# BLIND FF
2 93/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01K2
RATING ASME 150#
- LICENSOR A SLU,LN(Special Area),AV,TV PWHT / NACE Not required
- LICENSOR B
GASKET
RED. GASKET
SPECIAL GASKET
To suit pumps RUBBER GASKET 150# 6.0MM (162)
BOLT/NUT
A193-B7/A194-2H(ZN-CHROMATE) STUD/H.HEX
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
GATE
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101) (08,09,112)
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y (GA-102) (08,09,112)
350 - 600 A216-WCB/13Cr+HF 150# RF BB OS&Y GEAR (GA-132) (08,09,112)
15 - 40 A105/13Cr+HF 150# RF BB OS&Y (GA-101A)
BALL
50 - 50 A216-WCB/316+RTFE 150# RF FULL BORE F.S (BA-103)
50 - 50 A216-WCB/316+RTFE 150# RF FULL F.S EXT.BONNET (BA-103E)
KNIFE GATE
50 - 50 A395/316+URETHANE 150# WAFER BONNETLESS (KG-102) (08.09,18)
80 - 250 A395/316+URETHANE 150# WAFER BONNETLESS (KG-103) (08,09,18)
Notes :
08
09
10 These bolts shall be used at stainless steel flanges.
Valve description and size range taken from licensor A 'Piping Material Guidelines' document no. RA-PPG-001 rev C. Licensor
18
recommends using Clarkson Knife Gate Valves for this service.
109 The inside diameter of the Basalt lining should match the inside diameter of adjoining un-lined pipe.
Adjoining pieces of straight pipe and pipe bends of different wall thickness should be tapered to provide a relatively smooth flow
110
transition to minimize erosion.
To compensate for wall thinning during bending the schedule of pipe used for pipe bends should be one schedule higher than the
111
selected pipe schedule for straight pipe.
To be used for clean out connections only. Not for use in-line in slurry service. All piping starting with the tee at the common point
112
1.25meters downstream shall be basalt-lined.
113 Slurry recirculation pump discharge piping elbows shall be Basalt-Lined from the pump discharges to the common tie point.
162 For slurry transfer pump suction and discharge flanges as per note 11 on P&ID number RA1-1-3106.
2 94/334
CLASS: 01K2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W N B B
150 W W W W N N B B
Abbreviation
B Buttwelding Tee
2 95/334
CLASS: 01K2 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
80 LO LO LO LO LT LT
100 LO LO LO LO LO LT LT
150 LO LO LO LO LO LT LT LT
200 LO LO LO LO LO LT LT LT LT
250 LO LO LO LO LO LT LT LT LT LT
300 LO LO LO LO LO LT LT LT LT LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 96/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01NM
RATING ASME 150#
- LICENSOR A LGOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 20 B165-N04400 SMLS BE SCH80S ANNEALED
250 - 300 B725-N04400-CATEGORY.2 SMLS BE SCH10S ANNEALED
350 - 600 B725-N04400-CATEGORY.2 DSAW BE SCH10S ANNEALED
NIPPLE
ANNEALED
15 - 40 B165-N04400 SMLS BBE To match pipe thickness
L=3"
BEND (02,103)
ANNEALED
25 - 100 B165-N04400 SMLS BE SCH40S
3D
ANNEALED
150 - 200 B165-N04400 SMLS BE SCH10S
3D
ANNEALED
250 - 300 B725-N04400-CATEGORY.2 SMLS BE SCH10S
3D
ANNEALED
350 - 600 B725-N04400-CATEGORY.2 DSAW BE SCH10S
3D
SWAGE (02,103)
15 - 100 B366-WPNC-S SMLS BBE To match pipe Thickness ANNEALED
15 - 300 B366-WPNC-S SMLS BW To match pipe Thickness ANNEALED
350 - 600 B366-WPNC-W WELD BW To match pipe Thickness ANNEALED
CAP (02,103)
15 - 600 B366-WPNC-S SMLS BW To match pipe Thickness ANNEALED
WELDOLET (02,81)
50 - 600 B564-N04400 BW To match pipe Thickness ANNEALED
FLANGE (02,103)
15 - 600 B564-N04400 150# WN RF ANNEALED
WITH J.B
100 - 600 B564-N04400 150# WN RF
ANNEALED
15 - 600 B564-N04400 300# WN RF ANNEALED (12)
15 - 50 B564-N04400 1500# WN RTJ ANNEALED (82)
80 - 600 B564-N04400 900# WN RTJ ANNEALED (82)
BLIND FLANGE
15 - 20 B564-N04400 150# BLIND RF ANNEALED
25 - 600 A105(B127-N04400 3.2MM PLATED) 150# BLIND RF (12)
GASKET
15 - 600 SW(ALLOY400+GRAPH)IO:ALLOY400 150# RF 4.5MM (104,105)
15 - 600 SW(ALLOY400+GRAPH)IO:ALLOY400 300# RF 4.5MM (82,104,105)
BOLT/NUT
2 97/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A LGOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 ALLOY400/ALLOY400+HF 150# RF BB OS&Y (GA-301) (08-3,09)
50 - 300 ALLOY400/ALLOY400+HF 150# RF BB OS&Y (GA-307) (08-3,09)
350 - 600 ALLOY400/ALLOY400+HF 150# RF BB OS&Y GEAR (GA-315) (08-3,09)
GLOBE
15 - 200 ALLOY400/ALLOY400+HF 150# RF BB OS&Y (GL-301) (08-3,09)
250 - 300 ALLOY400/ALLOY400+HF 150# RF BB OS&Y GEAR (GL-302) (08-3,09)
CHECK
15 - 600 ALLOY400/ALLOY400+HF 150# RF BC SWING (CH-301) (62)
80 - 600 ALLOY400/ALLOY400+HF 150# WAFER DUAL PLATE (CH-302) (07,26,63)
BALL
15 - 150 ALLOY400/ALLOY400+RTFE 150# RF FULL BORE F.S (BA-301) (09)
200 - 600 ALLOY400/ALLOY400+RTFE 150# RF FULL BORE F.S GEAR (BA-302) (08-3,09)
Notes :
09
The use of copper or nickel alloy materials should be considered in piping systems in which high-velocity and/or high-turbulent
99 flow exists downstream of pressure let-down valves. Guidelines contained in CGA G4.4, Para 4.3.3.4 shall be followed for the
selection of materials in such areas.
102
103 The selection and use of materials shall be consistent with the velocity limits recommended in CGA G-4.4.
104 Alloy400 Gaskets only to be used up to a design temperature of 400℃
2 98/334
CLASS: 01NM
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W B B B
150 W W W W B B B B
200 W W W W W B B B B
250 W W W W W B B B B B
300 W W W W W W B B B B B
350 W W W W W W B B B B B B
400 W W W W W W B B B B B B B
Abbreviation
B Buttwelding Tee
2 99/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01PV0
RATING ASME 150#
- LICENSOR A PWHT / NACE Not applicable
- LICENSOR B PHY
PIPE
15 - 150 F441-CPVC4120 SMLS PE SCH80
ELBOW/REDUCER/TEE
15 - 150 F439-CPVC4120 SW To match pipe thickness
FLANGE
15 - 150 F439-CPVC4120 150# SW FF
BLIND FLANGE
15 - 150 F439-CPVC4120 150# BLIND FF
GASKET
ELAST. 50-60 SHORE A
15 - 150 150# FF 3.2MM
DUROMETER
BOLT/NUT
WITH F436
WASHERS
BALL
25 - 150 A395/DI(PFA.L) 150# FF RED. BORE F.S (BA-950)
PLUG
25 - 150 A395/DI(PFA.L) 150# FF REGULAR (PL-950)
CHECK
25 - 50 A395/DI(PFA.L) 150# FF BC SWING (CH-953)
80 - 200 A395/DI(PFA.L) 150# FF BC SWING (CH-951) (62)
BUTTERFLY
Notes :
01 Threaded pipe shall be derated 50% from the applicable pressure rating.
02 Threaded joints 50nb and larger shall be seal welded with solvent cement.
Union adaptors between thermoplastic and metallic pipe have a plastic socket for solvent cementing and a brass female pipe
03
threaded end.
Use washers on both ends of bolts. Corrosion protection is required for below ground use. Consideration shall be given to
04
fluoropolymer coated bolts for buried service.
Solvent cement shall be stored in an air conditioned area at approximately 21℃ and shall not be used past the date indicated on the
05
label or one year after date of manufacture.
2 100/334
CLASS: 01PV0
Branch Size (DN)

15 20 25 40 50 80 100 150
15 B
20 B B
Header Size (DN)
25 B B B
40 B B B B
50 N B B B B
80 N N N N B B
100 N N N N N B B
150 N N N N N B B B
Abbreviation
B Buttwelding Tee
2 101/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01R1
RATING ASME 150#
- LICENSOR A AV,TV,DR,PFW,RW,LP CORROSIVE WATER,PW PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 20 A312-TP304/304L SMLS BE SCH160
25 - 50 A312-TP304/304L SMLS BE SCH80S
80 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH20
350 - 600 A312-TP304/304L DSAW BE SCH20
NIPPLE (02,03)
SWAGE (02)
CAP (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
STUB-END (02)
15 - 300 A403-WP304/304L SMLS BW To match pipe thickness SHORT
PATTERN
SHORT
PATTERN
FLANGEOLET
15 - 20 A182-F304/304L 150# RF XXS
25 - 80 A182-F304/304L 150# RF XS
FLANGE (02)
15 - 600 A105(GALV) 150# LJ RF
100 - 600 A105(GALV) 150# LJ RF WITH J.B
15 - 600 A105(GALV) 300# LJ RF (12)
15 - 600 A105(GALV) 600# LJ RF (12)
15 - 600 A182-F304/304L 150# WN RF (82)
15 - 600 A182-F304/304L 150# WN FF (11,14)
BLIND FLANGE
15 - 600 A182-F304/304L 150# BLIND RF
15 - 50 A182-F304/304L 150# BLIND FF (11,14)
GASKET
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 102/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01R1
RATING ASME 150#
- LICENSOR A AV,TV,DR,PFW,RW,LP CORROSIVE WATER,PW PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-203A) (08,09)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-218A) (08,09)
350 - 600 A351-CF8M/316 150# RF BB OS&Y GEAR (GA-313) (08,09)
GLOBE
15 - 40 A182-F316/316 150# RF BB OS&Y (GL-212A) (08,09)
50 - 200 A351-CF8M/316 150# RF BB OS&Y (GL-212) (08,09)
250 - 300 A351-CF8M/316 150# RF BB OS&Y GEAR (GL-312) (08,09)
CHECK
15 - 40 A182-F316/316 150# RF BC SWING (CH-213) (08,09)
50 - 200 A351-CF8M/316 150# WAFER DUAL PLATE (CH-214) (08,09)
KNIFE GATE
50 - 50 Ni-RESIST CI/316+BUNA-N 150# WAFER BONNETLESS (KG-101) (08,09)
80 - 300 A395/316+URETHANE 150# WAFER BONNETLESS (KG-103) (08,09)
350 - 600 A395/316+URETHANE 150# WAFER BONNETLESS GEAR (KG-104) (08,09)
BALL
15 - 100 A351-CF8M/316+RTFE 150# RF RED. BORE F.S (BA-219) (08,09)
15 - 100 A351-CF8M/316+RTFE 150# RF RED. F.S EXT.BONNET (BA-219E)
3-WAY
REFERENCE
25 - 150 A351-CF8M/316+RTFE 150# RF RED. BORE F.S (08,09)
(BA-219)
200 - 200 A351-CF8M/316+RTFE 150# RF RED. BORE F.S GEARREFERENCE (08,09)
(BA-219)
PLUG
15 - 150 A351-CF8M/316+PTFE 150# RF REGULAR (PL-201) (08,09)
200 - 300 A351-CF8M/316+PTFE 150# RF REGULAR GEAR (PL-202)
Notes :
08
09
2 103/334
CLASS: 01R1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W N B B
150 W W W W N N B B
Abbreviation
B Buttwelding Tee
2 104/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01SA0
RATING ASME 150#
- LICENSOR A WDR,DW,DRC PWHT / NACE Not required
- LICENSOR B DW,DR,PW,RW,SPW,LO
PIPE (01)
15 - 40 A312-TP304/304L SMLS PE SCH40S
50 - 50 A312-TP304/304L SMLS BE SCH40S
80 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 600 A358-304/304L-Cl.1 EFW BE SCH10S
650 - 750 A358-304/304L-Cl.1 EFW BE SCH10
800 - 850 A358-304/304L-Cl.1 EFW BE 8.74MM
900 - 900 A358-304/304L-Cl.1 EFW BE STD
950 - 1000 A358-304/304L-Cl.1 EFW BE 10.31MM
1050 - 1050 A358-304/304L-Cl.1 EFW BE 11.13MM
1100 - 1100 A358-304/304L-Cl.1 EFW BE 11.91MM
1150 - 1200 A358-304/304L-Cl.1 EFW BE XS
1300 - 1300 A358-304/304L-Cl.1 EFW BE 14.27MM
1400 - 1500 A358-304/304L-Cl.1 EFW BE 15.88MM
NIPPLE (02)
15 - 40 A312-TP304/304L SMLS PBE To match pipe thickness L=3"
15 - 40 A312-TP304/304L SMLS POE/TOE To match pipe thickness L=3"
SWAGE (02)
15 - 40 A403-WP304/304L SMLS PBE To match pipe thickness
50 - 100 A403-WP304/304L SMLS BLE/PSE To match pipe thickness
15 - 40 A182-F304/304L SW 3000#
350 - 1500 A403-WP304/304L WELD BW To match pipe thickness RT 100%
CAP (02)
15 - 40 A182-F304/304L SW 3000#
FULL COUPLING/UNION (02)
15 - 40 A182-F304/304L SW 3000#
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (02)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
STUB-END
To match pipe thickness SHORT
PATTERN
50 - 300 A403-WP304/304L SMLS BW
350 - 600 A403-WP304/304L WELD BW To match pipe thickness SHORT

PATTERN
LONG
PATTERN
FLANGE (02)
15 - 40 A182-F304/304L 150# SW RF
50 - 600 A105(GALV) 150# LJ
ASME
650 - 1500 A182-F304/304L 150# WN RF
B16.47-A
100 - 600 A105(GALV) 150# LJ WITH J.B
WITH J.B
650 - 1500 A182-F304/304L 150# WN RF ASME
B16.47-A
50 - 600 A182-F304/304L 150# WN RF (82)
50 - 600 A105(GALV) 300# LJ
15 - 40 A182-F304/304L 600# SW RF
50 - 100 A105(GALV) 600# LJ (82)
50 - 600 A182-F304/304L 600# WN RF
50 - 600 A182-F304/304L 150# WN RF (82)
2 105/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BLIND FLANGE
15 - 600 A182-F304/304L 150# BLIND RF
ASME
650 - 1500 A182-F304/304L 150# BLIND RF
B16.47-A
LINE BLANK
15 - 600 A182-F304/304L 150# BLIND RF
ASME
650 - 1500 A182-F304/304L 150# BLIND RF
B16.47-A
GASKET
ASME
B16.47-A
BOLT/NUT
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-218)
350 - 600 A351-CF8M/316 150# RF BB OS&Y GEAR (GA-313)
ASME
650 - 1500 A351-CF8M/316 150# RF BB OS&Y GEAR B16.47-A
(GA-316)
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y (GA-204) (06)
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-202) (06)
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-203) (08-2)
WITH BY PASS
50 - 300 A351-CF8M/316 150# RF BB OS&Y DN20 GLOBE
V/V(GL-201)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-201)
50 - 200 A351-CF8M/316 150# RF BB OS&Y (GL-202)
250 - 600 A351-CF8M/316 150# RF BB OS&Y GEAR (GL-203)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-201) (61)
50 - 600 A351-CF8M/316 150# RF BC SWING (CH-203) (62)
ASME
650 - 1500 A351-CF8M/316 150# RF BC SWING B16.47-A (62)
(CH-217)
50 - 600 A351-CF8M/316 150# WAFER DUAL PLATE (CH-202) (07,26,63)
ASME
650 - 1500 A351-CF8M/316 150# WAFER DUAL PLATE B16.47-A (07,26,63)
(CH-216)
BALL
15 - 150 A351-CF8M/316+RTFE 150# RF RED. BORE F.S (BA-202) (09)
200 - 600 A351-CF8M/316+RTFE 150# RF RED. BORE F.S GEAR (BA-206) (09)
ASME
650 - 1500 A351-CF8M/316+RTFE 150# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-204)
80 - 150 A351-CF8M/316+RTFE 150# RF FULL BORE F.S (BA-203) (08-2,09)
200 - 600 A351-CF8M/316+RTFE 150# RF FULL BORE F.S GEAR (BA-207) (08-2,09)
ASME
650 - 1500 A351-CF8M/316+RTFE 150# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-205)
80 - 150 A351-CF8M/316+RTFE 150# RF FULL F.S EXT.BONNET (BA-203E)
15 - 40 A351-CF8M/316+RTFE 300# SW/NPT RED. BORE F.S (BA-208) (06,09)
2 106/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
BUTTERFLY
50 - 150 A351-CF8M/316+PTFE 150# WAFER LEVER (BF-201) (07,09)
200 - 600 A351-CF8M/316+PTFE 150# WAFER GEAR (BF-202) (07,09)
ASME
650 - 1500 A351-CF8M/316+PTFE 150# WAFER GEAR B16.47-A (07,09)
(BF-246)
50 - 150 A351-CF8M/316+PTFE 150# LUG LEVER (BF-203) (07,09)
200 - 600 A351-CF8M/316+PTFE 150# LUG GEAR (BF-204) (07,09)
ASME
650 - 1500 A351-CF8M/316+PTFE 150# LUG GEAR B16.47-A (07,09)
(BF-247)
(TAPPED
LUG) FOR
50 - 150 A351-CF8M/316+PTFE 150# LUG LEVER
POTABLE
WATER
PLUG
15 - 150 A351-CF8M/316+PTFE 150# RF REGULAR (PL-203) (09)
200 - 500 A351-CF8M/316+PTFE 150# RF REGULAR GEAR (PL-204) (09)
LOW
EMISSION
15 - 150 A351-CF8M/316+PTFE 150# RF REGULAR (09,26)
BONNET
(PL-205)
LOW
EMISSION
200 - 500 A351-CF8M/316+PTFE 150# RF REGULAR GEAR (09,26)
BONNET
(PL-206)
KNIFE GATE
50 - 50 Ni-RESIST CI/316+BUNA-N 150# WAFER BONNETLESS (KG-101)
80 - 300 A395/316+URETHANE 150# WAFER BONNETLESS (KG-103)
Notes :
09
2 107/334
CLASS: 01SA0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 10001050110011501200130014001500
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
200 W W W W W N N B B
250 W W W W W N N N B B
300 W W W W W N N R R B B
350 W W W W W N N R R R B B
400 W W W W W R R R R R R B B
Header Size (DN)
450 W W W W W R R R R R R R B B
500 W W W W W R R R R R R R R B B
600 W W W W W R R R R R R R R R B B
650 W W W W W R R R R R R R R R R B B
700 W W W W W R R R R R R R R R R R B B
750 W W W W W R R R R R R R R R R R R B B
800 W W W W W R R R R R R R R R R R R R B B
850 W W W W W R R R R R R R R R R R R R R B B
900 W W W W W R R R R R R R R R R R R R R R B B
950 W W W W W R R R R R R R R R R R R R R R R B B
1000 W W W W W R R R R R R R R R R R R R R R R R B B
1050 W W W W W R R R R R R R R R R R R R R R R R R B B
1100 W W W W W R R R R R R R R R R R R R R R R R R R B B
1150 W W W W W R R R R R R R R R R R R R R R R R R R R B B
1200 W W W W W R R R R R R R R R R R R R R R R R R R R R B B
1300 W W W W W R R R R R R R R R R R R R R R R R R R R R R B B
1400 W W W W W R R R R R R R R R R R R R R R R R R R R R R R B B
1500 W W W W W R R R R R R R R R R R R R R R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 108/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01S0
RATING ASME 150#
- LICENSOR B POX, LSS(For Sulphur Pit)
PIPE (01)
15 - 20 A312-TP316/316L SMLS PE SCH80S
25 - 40 A312-TP316/316L SMLS PE SCH40S
50 - 100 A312-TP316/316L SMLS BE SCH40S
150 - 300 A312-TP316/316L SMLS BE SCH10S
350 - 600 A312-TP316/316L DSAW BE SCH10S
PIPE(For Sulphur Pit)
25 - 25 SA312-TP316L SMLS PE SCH40S (101)
NIPPLE (02)
SWAGE (02)
15 - 40 A182-F316/316L SW 3000#
CAP (02)
15 - 40 A182-F316/316L SW 3000#
15 - 40 A182-F316/316L SW 3000#
THREDOLET (163)
15 - 40 A182-F316/316L THRD 3000#
PLUGS
15 - 40 A182-F316/316L THRD HEX
WELDOLET (02,81)
STUB-END
PATTERN
FLANGE (02)
15 - 40 A182-F316/316L 150# SW RF
50 - 600 A105(GALV) 150# LJ
100 - 600 A105(GALV) 150# LJ WITH J.B
50 - 600 A182-F316/316L 150# WN RF (82)
BLIND FLANGE
15 - 600 A182-F316/316L 150# BLIND RF
LINE BLANK
15 - 350 A182-F316/316L 150# FIG-8 FF
400 - 600 A182-F316/316L 150# BLK&SPC FF
GASKET
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 109/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B POX, LSS(For Sulphur Pit)
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-218)
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-202) (06)
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y (GA-204) (06)
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-203) (08-2)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-201)
50 - 150 A351-CF8M/316 150# RF BB OS&Y (GL-202)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-201) (61)
BALL
15 - 40 A351-CF8M/316+RTFE 300# SW RED. BORE F.S (BA-201) (09)
BUTTERFLY
50 - 150 A351-CF8M/316+PTFE 150# LUG LEVER (BF-203) (07,09,26)
200 - 600 A351-CF8M/316+PTFE 150# LUG GEAR (BF-204) (07,09,26)
PLUG
LOW
EMISSION
BONNET
(PL-205)
LOW
EMISSION
BONNET
(PL-206)
Notes :
09
101 This pipe shall be used for sulphur pit risers. And shall get a certification at ASME.
2 110/334
CLASS: 01S0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W N B B
150 W W W W N N B B
300 W W W W N N R R R B B
350 W W W W N N R R R R B B
400 W W W W R R R R R R R B B
450 W W W W R R R R R R R R B B
500 W W W W R R R R R R R R R B B
600 W W W W R R R R R R R R R R B B
Abbreviation
B Buttwelding Tee
2 111/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B AMMONIA STRIPPING
PIPE (01)
15 - 20 A312-TP316/316L SMLS PE SCH80S
25 - 40 A312-TP316/316L SMLS PE SCH40S
50 - 100 A312-TP316/316L SMLS BE SCH40S
150 - 300 A312-TP316/316L SMLS BE SCH10S
350 - 600 A312-TP316/316L DSAW BE SCH20
NIPPLE (02)
SWAGE (02)
15 - 40 A182-F316/316L SW 3000#
CAP (02)
15 - 40 A182-F316/316L SW 3000#
15 - 40 A182-F316/316L SW 3000#
THREDOLET (163)
15 - 40 A182-F316/316L THRD 3000#
PLUGS
15 - 40 A182-F316/316L THRD HEX
WELDOLET (02,81)
STUB-END
PATTERN
FLANGE (02)
15 - 40 A182-F316/316L 150# SW RF
50 - 600 A105(GALV) 150# LJ
100 - 600 A105(GALV) 150# LJ WITH J.B
50 - 600 A182-F316/316L 150# WN RF (82)
15 - 20 A182-F316/316L 300# SW RF
50 - 100 A182-F316/316L 300# WN RF
BLIND FLANGE
15 - 600 A182-F316/316L 150# BLIND RF
15 - 600 A182-F316/316L 300# BLIND RF
LINE BLANK
15 - 350 A182-F316/316L 150# FIG-8 RF
400 - 600 A182-F316/316L 150# BLK&SPC RF
GASKET
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 112/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-218)
15 - 40 A182-F316/316L 150# RF BB OS&Y (GA-202) (06)
15 - 40 A182-F316/316L 800# SW/NPT BB OS&Y (GA-204) (06)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-201)
50 - 150 A351-CF8M/316 150# RF BB OS&Y (GL-202)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-201) (61)
BALL
BUTTERFLY
50 - 150 A351-CF8M/316+PTFE 150# LUG LEVER (BF-203) (07,09,26)
PLUG
LOW
EMISSION
BONNET
(PL-205)
LOW
EMISSION
BONNET
(PL-206)
Notes :
09
2 113/334
CLASS: 01S1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W N B B
150 W W W W N N B B
300 W W W W N N R R R B B
350 W W W W N N R R R R B B
Abbreviation
B Buttwelding Tee
2 114/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01SS
RATING ASME 150#
- LICENSOR A PW,RW,SPW,DR,LO PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 40 A312-TP304/304L SMLS PE SCH40S
50 - 50 A312-TP304/304L SMLS BE SCH40S
80 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 600 A312-TP304/304L DSAW BE SCH10S
NIPPLE (02)
SWAGE (02)
15 - 40 A182-F304/304L SW 3000#
CAP (02)
15 - 40 A182-F304/304L SW 3000#
FULL COUPLING/SOCKOLET (02)
15 - 40 A182-F304/304L SW 3000#
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
STUB-END (02)
PATTERN
SHORT
PATTERN
FLANGE (02)
15 - 40 A182-F304/304L 150# SW RF
50 - 600 A105(GALV) 150# LJ
15 - 40 A182-F304/304L 600# SW RF
100 - 600 A105(GALV) 150# LJ WITH J.B
50 - 600 A182-F304/304L 150# WN RF (82)
80 - 600 A182-F304/304L 900# WN RTJ
BLIND FLANGE
15 - 300 A182-F304/304L 150# BLIND RF
GASKET
80 - 600 SS304/304L 900# RTJ OVAL RING
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 115/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR A PW,RW,SPW,DR,LO PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201) (09)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-218) (08-2,09)
350 - 600 A351-CF8M/316 150# RF BB OS&Y GEAR (GA-313) (08-2,09)
15 - 40 A182-F304/304L 800# SW/NPT BB OS&Y (GA-204) (06)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-201) (09)
50 - 200 A351-CF8M/316 150# RF BB OS&Y (GL-202) (09)
250 - 300 A351-CF8M/316 150# RF BB OS&Y GEAR (GL-203) (09)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-201) (61)
BALL
BUTTERFLY
50 - 150 A351-CF8M/316+PTFE 150# LUG LEVER (BF-203) (07,09,26-2)
200 - 600 A351-CF8M/316+PTFE 150# LUG GEAR (BF-204) (07,09,26-2)
PLUG
Notes :
09
2 116/334
CLASS: 01SS
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S W B B
150 S S S S W N B B
200 S S S S W N N B B
250 S S S S W N N N B B
300 S S S S W W W R R B B
350 S S S S W W W R R R B B
400 S S S S W W W R R R R B B
450 S S S S W W W W R R R R B B
500 S S S S W W W W R R R R R B B
600 S S S S W W W W W R R R R R B B
Abbreviation

Buttwelding Tee
2 117/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01T1
RATING ASME 150#
CORR. ALLOWANCE 1.6MM(3.2MM for Jacket Core Piping) DES. TEMP.(C) -29 (MDMT) to 425 (NOTE 35)
- LICENSOR A PWHT / NACE Reqd per B31.3 Sec 331
- LICENSOR B SV,LSU,SGS,PSOG for thk > 19.05mm
PIPE (01)
15 - 20 A106-B SMLS BE SCH160
25 - 600 A106-B SMLS BE SCH80
NIPPLE (02,83)
15 - 40 A106-B SMLS BBE To match pipe thickness L=3"
ELBOW/TEE/REDUCER/CROSS (02)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
CAP (02)
FLANGE (02)
15 - 600 A105 150# WN RF (84)
100 - 600 A105 150# WN RF WITH J.B
REDUCING FLANGE
15 - 600 A105 150# SO RF
650 - 650 A105 150# WN RF
15 - 600 A105 300# SO RF (12)
BLIND FLANGE
15 - 600 A105 150# BLIND RF (84)
LINE BLANK
15 - 600 A105 150# FIG-8 FF
GASKET
15 - 600 SW(304+GRAP)IO:304/CS 150# RF 4.5MM
15 - 600 SW(304+GRAP)IO:304/CS 300# RF 4.5MM (82)
REDUCING GASKET
15 - 600 SW(304+GRAP)IO:304/CS 150# RF 4.5MM
BOLT/NUT (82-2)
GATE
FULL
15 - 40 A105/13Cr+HF 150# RF BB OS&Y JACKET
(GA-903)
FULL
50 - 300 A216-WCB/13Cr+HF 150# RF BB OS&Y JACKET
(GA-904)
CHECK
FULL
15 - 600 A216-WCB/13Cr+HF 150# RF BC SWING JACKET
(CH-903)
PLUG
FULL
25 - 150 A216-WCB/316+PTFE 150# RF REGULAR JACKET (09)
(PL-903)
FULL
200 - 300 A216-WCB/316+PTFE 150# RF REGULAR GEAR JACKET (09)
(PL-904)
2 118/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01T1
RATING ASME 150#
CORR. ALLOWANCE 1.6MM(3.2MM for Jacket Core Piping) DES. TEMP.(C) -29 (MDMT) to 425 (NOTE 35)
- LICENSOR B SV,LSU,SGS,PSOG for thk > 19.05mm
BALL
FULL
25 - 150 A216-WCB/316+RTFE 150# RF RED. BORE F.S JACKET (09)
(BA-903)
FULL
200 - 300 A216-WCB/316+RTFE 150# RF RED. BORE F.S GEAR JACKET (09)
(BA-904)
FULL
200 - 300 A216-WCB/316+RTFE 150# RF FULL BORE F.S GEAR JACKET (09)
(BA-905)
Size Combination Table
Jacket Pipe Special Jacket Supply, Return and

Core Pipe (01T1)
(01T1J) Fittings Jumper
15 25 15
20 40 15
25 50 15
40 65 20
50 80 20
50 100 20
80 100 20
80 150 20
100 150 20
150 200 25
200 250 25
250 300 25
300 400 25
600 650 tba
Notes :
09
35
323.2.2 of ASME B31.3.
82-2 Stud-blot engths may need to be longer because of increased thickness of the insert flange.
Threaded joints shall only be permitted at jacket jumper and instrument connections. Threaded joints, except tube fittings and
83
instruments, shall be seal-welded.
84 The non-reducing flange is used to mate against equipment or at a spec break to piping with a non-reducing flange.
2 119/334
CLASS: 01T1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 N B B B
50 N N B B B
80 N N N B B B
Header Size (DN)
100 N N N N B B B
150 N N N N N B B B
200 N N N N N N B B B
250 N N N N N N B B B B
300 N N N N N N N B B B B
350 N N N N N N N B B B B B
400 N N N N N N N B B B B B B
450 N N N N N N N N B B B B B B
500 N N N N N N N N B B B B B B B
600 N N N N N N N N N B B B B B B B
Abbreviation
B Buttwelding Tee
2 120/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01T1J
RATING ASME 150#
- LICENSOR B LS for thk > 19.05mm
PIPE (01)
15 - 20 A53-B SMLS BE SCH160
25 - 50 A53-B SMLS BE SCH80
80 - 200 A53-B ERW BE SCH40
250 - 650 A53-B ERW BE SCH20
NIPPLE (02,83)
15 - 40 A53-B SMLS PBE To match pipe thickness L=3"
15 - 40 A53-B SMLS POE/TOE To match pipe thickness L=3"
ELBOW (02,85)
15 - 50 A234-WPB SMLS BW To match pipe thickness FOR
JACKET
FOR
JACKET
REDUCER (02,85)
TEE/CROSS (02,85)
15 - 800 A234-WPB SPLIT BW To match pipe thickness
CAP (02,85)
COUPLING
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS
15 - 40 A105 THRD HEX
FLANGE
15 - 100 A105 150# SO RF (84)
100 - 100 A105 150# SO RF WITH J.B
BLIND FLANGE
15 - 100 A105 150# BLIND RF (84)
GASKET
15 - 100 SW(304+GRAP)IO:304/CS 150# RF 4.5MM
BOLT/NUT (82-2)
GATE
Notes :
35
323.2.2 of ASME B31.3.
82-2 Stud-blot lengths may need to be longer because of increased thickness of the insert flange.
Threaded joints shall only be permitted at jacket jumper and instrument connections. Threaded joints, except tube fittings and
83
instruments, shall be seal-welded.
84 The non-reducing flange is used to mate against equipment or at a spec break to piping with a non-reducing flange. Ej
85 shall be 0.80 if jacket component is split and rewelded.
86 These valves shall be used for jacket vent and drain applications.
2 121/334
CLASS: 01T1J
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650
15 B
20 B B
25 B B B
40 B B B B
50 C B B B B
80 C C C C B B
Header Size (DN)
100 C C C C N B B
150 C C C C N N B B
200 C C C C N N N B B
250 C C C C N N N N B B
300 C C C C N N N N N B B
350 C C C C N N N N N N B B
400 C C C C N N N N N N N B B
450 C C C C N N N N N N N N B B
500 C C C C N N N N N N N N N B B
600 C C C C N N N N N N N N N N B B
650 C C C C N N N N N N N N N N N B B
Abbreviation
B Buttwelding Tee
C Half Coupling
2 122/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01U0
RATING ASME 150#
- LICENSOR A AV,TV PWHT / NACE Not required
- LICENSOR B
PIPE
15 - 50 A312-TP304/304L SMLS BE SCH40S (01)
80 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 600 A358-304/304L-Cl.1 EFW BE SCH10S
1050 - 1050 A358-304/304L-Cl.1 EFW BE 11.13MM
350 - 600 A312-TP304/304L DSAW BE SCH10S (100)
NIPPLE (02)
SWAGE
ELBOW/TEE/REDUCER/CAP (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
STUB-END (02)
PATTERN
SHORT
350 - 600 A403-WP304/304L WELD BW To match pipe thickness PATTERN
RT 100%
FLANGE (02)
15 - 600 A105(GALV) 150# LJ
ASME
1050- 1050 A182-F304/304L 150# WN RF
B16.47-A
100 - 600 A105(GALV) 150# LJ WITH J.B
WITH J.B
1050- 1050 A182-F304/304L 150# WN RF ASME
B16.47-A
15 - 600 A182-F304/304L 150# WN RF (82)
15 - 80 A105(GALV) 600# LJ (82)
80 - 100 A182-F304/304L 600# WN RF
BLIND FLANGE
15 - 600 A182-F304/304L 150# BLIND RF
GASKET
ASME
B16.47-A
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 123/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01U0
RATING ASME 150#
- LICENSOR A AV,TV PWHT / NACE Not required
- LICENSOR B
VALVES FOR LICENSOR A FLUID CODES : AV, TV (Operating between -29℃ and 425℃)
GATE
15 - 40 A182-F316/316 150# RF BB OS&Y (GA-214) (08-2,09)
50 - 100 A351-CF8M/316 150# RF BB OS&Y (GA-214A) (08-2,09)
GLOBE
REFERENCE
50 - 50 A351-CF8M/316 150# RF BB OS&Y (08-2,09)
(GA-214)
CHECK
50 - 600 A351-CF8M/316 150# WAFER DUAL PLATE (CH-214) (07,08-2,09)
KNIFE GATE
1050 - 1050 A395/316+URETHANE 150# LUG BONNETLESS GEAR (KG-104) (08-2,09,18)
BALL
50 - 50 A351-CF8M/316+RTFE 150# RF RED. BORE F.S (BA-202)
BUTTERFLY
80 - 150 A395(PTFE.L)/17-4PH+C.PTFE 150# LUG LEVER (BF-209) (08-2,09)
200 - 600 A395(PTFE.L)/17-4PH+C.PTFE 150# LUG GEAR (BF-210) (08-2,09)
Note :
09
Valve description and size range taken from licensor A 'Piping Material Guidelines' document no. RA-PPG-001 rev C. Licensor
18
recommends using Clarkson Knife Gate Valves for this service.
100 These pipes are possible to use instead of A358-304/304L-Cl.1 at License A.
2 124/334
CLASS: 01U0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W N B B
Abbreviation
B Buttwelding Tee
2 125/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01U0B
RATING ASME 150#
- LICENSOR B PCR,LCPM,WSA(HOLD)
PIPE (01)
15 - 50 A312-TP304/304L SMLS BE SCH40S
80 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 600 A358-304/304L-Cl.1 EFW BE SCH10S
650 - 650 A358-304/304L-Cl.1 EFW BE 7.14MM
700 - 750 A358-304/304L-Cl.1 EFW BE SCH10
800 - 850 A358-304/304L-Cl.1 EFW BE 8.74MM
900 - 900 A358-304/304L-Cl.1 EFW BE STD
950 - 1000 A358-304/304L-Cl.1 EFW BE 10.31MM
1050 - 1050 A358-304/304L-Cl.1 EFW BE 11.13MM
1100 - 1100 A358-304/304L-Cl.1 EFW BE 11.91MM
1150 - 1200 A358-304/304L-Cl.1 EFW BE XS
1300 - 1300 A358-304/304L-Cl.1 EFW BE 14.27MM
1400 - 1500 A358-304/304L-Cl.1 EFW BE 15.88MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
WELDOLET (02,81)
PLUGS
15 - 40 A182-F304/304L THRD HEX
2 126/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
FLANGE (02)
15 - 40 A182-F304/304L 300# WN RF
50 - 600 A182-F304/304L 150# WN RF
ASME
650 - 1500 A182-F304/304L 150# WN RF
B16.47-A
100 - 600 A182-F304/304L 150# WN RF WITH J.B
WITH J.B
650 - 1500 A182-F304/304L 150# WN RF ASME
B16.47-A
50 - 600 A182-F304/304L 300# WN RF (82)
ASME
650 - 1500 A182-F304/304L 300# WN RF (82)
B16.47-A
15 - 600 A182-F304/304L 600# WN RF (82)
ASME
650 - 1500 A182-F304/304L 600# WN RF (82)
B16.47-A
REDUCING FLANGE
50 - 50 A182-F304/304L 150# WN RF
BLIND FLANGE
15 - 40 A182-F304/304L 350# BLIND RF
50 - 600 A182-F304/304L 150# BLIND RF
ASME
650 - 1500 A182-F304/304L 150# BLIND RF
B16.47-A
15 - 40 A182-F304/304L 150# BLIND RF
LINE BLANK
15 - 40 A182-F304/304L 300# FIG-8 FF
50 - 350 A182-F304/304L 150# FIG-8 FF
400 - 600 A182-F304/304L 150# BLK&SPC FF
ASME
650 - 1500 A182-F304/304L 150# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
ASME
B16.47-A
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
ASME
650 - 1500 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
B16.47-A
BOLT/NUT
2 127/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
CHECK VALVES FOR LICENSOR B FLUID CODES NON-CORROSIVE SEVICE
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-201) (61)
ASME
650 - 1500 A351-CF8M/316 150# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-216)
VALVES FOR FLUID CODES : PCR, LCPM (Operating between -46℃ and 300℃)
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201) (09)
50 - 300 A351-CF8M/316 150# RF BB OS&Y (GA-203) (08-2,09)
ASME
650 - 1500 A351-CF8M/316 150# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-313)
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y (GA-204) (06,09)
15 - 40 A182-F316/316 300# RF BB OS&Y (GA-206) (09)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-201) (09)
50 - 200 A351-CF8M/316 150# RF BB OS&Y (GL-202) (09)
15 - 40 A182-F316/316 300# RF BB OS&Y (GL-227) (09)
BUTTERFLY
50 - 150 A351-CF8M/316+PTFE 150# WAFER LEVER (BF-201) (09)
200 - 600 A351-CF8M/316+PTFE 150# WAFER GEAR (BF-202) (09)
ASME
(BF-246)
ASME
650 - 1500 A351-CF8M/316+PTFE 150# LUG GEAR B16.47-A (07,09,26)
(BF-247)
BALL
ASME
(BA-204)
15 - 40 A351-CF8M/316+RTFE 300# SW RED. F.S EXT.BONNET (BA-201E)
ASME
(BA-205)
2 128/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
Note :
09
2 129/334
CLASS: 01U0B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 10001050110011501200130014001500
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 130/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01U0C
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) (NOTE 44) -196 to -47
(-210C SHORT TERM)
- LICENSOR B SGT,RECT,DRRT,LCD,MCD,PSOG,FLRC,WWR(HOLD)
PIPE (01)
15 - 50 A312-TP304/304L SMLS BE SCH40S
80 - 300 A312-TP304/304L SMLS BE SCH10S
350 - 600 A358-304/304L-Cl.1 EFW BE SCH10S
650 - 650 A358-304/304L-Cl.1 EFW BE 7.14MM
700 - 750 A358-304/304L-Cl.1 EFW BE SCH10
800 - 850 A358-304/304L-Cl.1 EFW BE 8.74MM
900 - 900 A358-304/304L-Cl.1 EFW BE STD
950 - 1000 A358-304/304L-Cl.1 EFW BE 10.31MM
1050 - 1050 A358-304/304L-Cl.1 EFW BE 11.13MM
1100 - 1100 A358-304/304L-Cl.1 EFW BE 11.91MM
1150 - 1200 A358-304/304L-Cl.1 EFW BE XS
1300 - 1300 A358-304/304L-Cl.1 EFW BE 14.27MM
1400 - 1500 A358-304/304L-Cl.1 EFW BE 15.88MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
WELDOLET (02,81)
PLUGS
15 - 40 A182-F304/304L THRD HEX
FLANGE (02)
15 - 40 A182-F304/304L 300# WN RF
50 - 600 A182-F304/304L 150# WN RF
ASME
650 - 1500 A182-F304/304L 150# WN RF
B16.47-A
100 - 600 A182-F304/304L 150# WN RF WITH J.B
WITH J.B
650 - 1500 A182-F304/304L 150# WN RF ASME
B16.47-A
50 - 600 A182-F304/304L 300# WN RF (82)
ASME
650 - 1500 A182-F304/304L 300# WN RF (82)
B16.47-A
15 - 600 A182-F304/304L 600# WN RF (82)
ASME
650 - 1500 A182-F304/304L 600# WN RF (82)
B16.47-A
15 - 50 A182-F304/304L 1500# WN RTJ (82)
REDUCING FLANGE
50 - 50 A182-F304/304L 150# WN RF
BLIND FLANGE
15 - 40 A182-F304/304L 300# BLIND RF
50 - 600 A182-F304/304L 150# BLIND RF
ASME
650 - 1500 A182-F304/304L 150# BLIND RF
B16.47-A
LINE BLANK
15 - 40 A182-F304/304L 300# FIG-8 FF
50 - 350 A182-F304/304L 150# FIG-8 FF
400 - 600 A182-F304/304L 150# BLK&SPC FF
ASME
650 - 1500 A182-F304/304L 150# BLK&SPC FF
B16.47-A
2 131/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
(-210C SHORT TERM)
GASKET
ASME
B16.47-A
ASME
B16.47-A
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
ASME
650 - 1500 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
B16.47-A
BOLT/NUT
VALVES FOR FLUID CODES : DRRT, FLRC, SGT, RECT, PSOG (Operating below -46℃) IN CORROSIVE SERVICE
GATE
EXTENDED
15 - 40 A182-F316/316 300# RF BB OS&Y B.S BONNET (09)
(GA-276)
EXTENDED
50 - 80 A351-CF8M/316 150# RF BB OS&Y B.S BONNET (08-2,09)
(GA-278)
EXTENDED
BB OS&Y SPRING
100 - 300 A351-CF8M/316 150# RF BONNET (08-2,09)
LOADED
(GA-278)
EXTENDED
350 - 600 A351-CF8M/316 150# RF BB OS&Y SP.L GEAR BONNET (08-2,09)
(GA-279)
EXTENDED
BONNET
650 - 750 A351-CF8M/316 150# RF BB OS&Y SP.L GEAR ASME
B16.47-A(GA-
279A)
GLOBE
EXTENDED
(GL-275)
EXTENDED
50 - 80 A351-CF8M/316 150# RF BB OS&Y B.S BONNET (09)
(GL-276)
EXTENDED
BB OS&Y SPRING
100 - 200 A351-CF8M/316 150# RF BONNET (09)
LOADED
(GL-276)
EXTENDED
250 - 400 A351-CF8M/316 150# RF BB OS&Y SP.L GEAR BONNET (09)
(GL-277)
CHECK
15 - 40 A182-F316/316 300# RF BC LIFT (CH-375) (61)
ASME
(CH-378)
2 132/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
(-210C SHORT TERM)
VALVES FOR FLUID CODES : LCD, MCD (Operating below -46℃) Linde Fluid Group 016
GATE
EXTENDED
15 - 40 A182-F316/316 800# SW BB OS&Y BONNET (09)
(GA-250)
EXTENDED
50 - 300 A351-CF8M/316 150# RF BB OS&Y BONNET (08-2,09)
(GA-253)
EXTENDED
350 - 600 A351-CF8M/316 150# RF BB OS&Y GEAR BONNET (08-2,09)
(GA-254)
EXTENDED
BONNET
650 - 1500 A351-CF8M/316 150# RF BB OS&Y GEAR ASME (08-2,09)
B16.47-A
(GA-256)
EXTENDED
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y BONNET (06,09)
(GA-252)
EXTENDED
15 - 40 A182-F316/316 300# RF BB OS&Y BONNET (09)
(GA-251)
GLOBE
EXTENDED
(GL-250)
EXTENDED
50 - 200 A351-CF8M/316 150# RF BB OS&Y BONNET (09)
(GL-251)
EXTENDED
250 - 400 A351-CF8M/316 150# RF BB OS&Y GEAR BONNET (09)
(GL-252)
BUTTERFLY
EXTENDED
50 - 150 A351-CF8M/316+RTFE 150# WAFER LEVER BONNET (07,09)
(BF-248)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 150# WAFER GEAR BONNET (07,09)
(BF-229)
EXTENDED
BONNET
650 - 1500 A351-CF8M/316+RTFE 150# WAFER GEAR ASME (07,09)
B16.47-A
(BF-250)
EXTENDED
50 - 150 A351-CF8M/316+RTFE 150# LUG LEVER BONNET (07,09)
(BF-251)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 150# LUG GEAR BONNET (07,09,26)
(BF-252)
EXTENDED
BONNET
650 - 1500 A351-CF8M/316+RTFE 150# LUG GEAR ASME (07,09,26)
B16.47-A
(BF-253)
2 133/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
(-210C SHORT TERM)
BALL
EXTENDED
15 - 40 A351-CF8M/316+RTFE 300# RF RED. BORE F.S BONNET (09)
(BA-351)
EXTENDED
(BA-352)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 150# RF RED. BORE F.S GEAR BONNET (09)
(BA-354)
EXTENDED
BONNET
650 - 1500 A351-CF8M/316+RTFE 150# RF RED. BORE F.S GEAR ASME (09)
B16.47-A
(BA-356)
EXTENDED
50 - 150 A351-CF8M/316+RTFE 150# RF FULL BORE F.S BONNET (08-2,09)
(BA-353)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 150# RF FULL BORE F.S GEAR BONNET (08-2,09)
(BA-355)
EXTENDED
BONNET
650 - 1500 A351-CF8M/316+RTFE 150# RF FULL BORE F.S GEAR ASME (08-2,09)
B16.47-A
(BA-357)
Note :
09
2 134/334
CLASS: 01U0C
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 10001050110011501200130014001500
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 135/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01Y0
RATING ASME 150#
- LICENSOR B PCR
PIPE (01,100)
15 - 20 A790-S31803 SMLS BE SCH80S
25 - 100 A790-S31803 SMLS BE SCH40S
150 - 600 A790-S31803 SMLS BE SCH10S
NIPPLE (02,114)
15 - 40 A790-S31803 SMLS BBE To match pipe thickness L=3"
SWAGE (02,114)
15 - 100 A815-S31803 SMLS BBE To match pipe thickness
15 - 600 A815-S31803 SMLS BW To match pipe thickness
LATERAL
THREDOLET (163)
15 - 40 A182-F51 THRD 3000#
PLUGS (163)
15 - 40 A182-F51 THRD HEX
WELDOLET (02,81)
50 - 600 A182-F51 BW To match pipe thickness
STUB-END (02)
15 - 600 A815-S31803 SMLS BE To match pipe thickness SHORT
PATTERN
FLANGE (02)
15 - 600 A105(GALV) 150# LJ
100 - 600 A105(GALV) 150# LJ WITH J.B
15 - 600 A182-F51 150# WN RF (82)
15 - 50 A182-F51 300# WN RF (12,82)
BLIND FLANGE
15 - 600 A182-F51 150# BLIND RF
LINE BLANK
15 - 350 A240-S31803 150# FIG-8 FF
400 - 600 A240-S31803 150# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 150# RF 4.5MM
15 - 600 SW(316+GRAP)IO:316 300# RF 4.5MM (82)
BOLT/NUT
A193-B8/A194-8 STUD/H.HEX (10)
GATE
15 - 40 A351-CD4MCu/DUPLEX 2205 150# RF BB OS&Y (GA-601) (09)
350 - 600 A351-CD4MCu/DUPLEX 2205 150# RF BB OS&Y GEAR (GA-603) (09)
GLOBE
15 - 40 A351-CD4MCu/DUPLEX 2205 150# RF BB OS&Y (GL-601) (09)
250 - 600 A351-CD4MCu/DUPLEX 2205 150# RF BB OS&Y GEAR (GL-603) (09)
CHECK
15 - 40 A351-CD4MCu/DUPLEX 2205 300# BW BC LIFT (CH-601) (61)
50 - 600 A351-CD4MCu/DUPLEX 2205 150# RF BC SWING (CH-602) (62)
80 - 600 A351-CD4MCu/DUPLEX 2205 150# WAFER DUAL PLATE (CH-603) (07,26,63)
BUTTERFLY
150 - 150 A351-CD4MCu/DUPLEX 2205 150# WAFER LEVER (BF-603)
200 - 200 A351-CD4MCu/DUPLEX 2205 150# WAFER GEAR (BF-603)
2 136/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 150#
- LICENSOR B PCR
Note :
09
2 137/334
CLASS: 01Y0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W R B B
150 W W W W R R B B
200 W W W W R R R B B
250 W W W W R R R R B B
300 W W W W R R R R R B B
350 W W W W R R R R R R B B
Abbreviation
B Buttwelding Tee
2 138/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01Z0A
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) HOLD
TYPICAL SERVICE DES. PRES.(barg) HOLD
PIPE (01)
15 - 40 B619-N10276-Cl.1 EFW BE SCH40S
50 - 600 B619-N10276-Cl.1 EFW BE SCH10S
SWAGE (02,114)
SOLUTION
15 - 100 B366-N10276 WELD BBE To match pipe thickness
ANNEALED
ELBOW/TEE/REDUCER/CAP (02,100)
SOLUTION
15 - 600 B366-N10276 WELD BW To match pipe thickness
ANNEALED
THREDOLET (163)
SOLUTION
15 - 40 B564-N10276 THRD 3000#
ANNEALED
PLUGS (163)
SOLUTION
15 - 40 B564-N10276 THRD HEX
ANNEALED
SOLUTION
40 - 600 B564-N10276 BW To match pipe thickness
ANNEALED
STUB-END (02,100)
SHORT
PATTERN
15 - 300 B366-N10276 WELD BE To match pipe thickness
SOLUTION
ANNEALED
FLANGE (02,100)
15 - 600 A105 150# LJ
SOLUTION
15 - 600 B564-N10276 150# WN RF
ANNEALED
SOLUTION
15 - 600 B564-N10276 300# WN RF
ANNEALED
BLIND FLANGE
15 - 600 A105(C276 CLAD) 150# BLIND RF
15 - 600 A105(C276 CLAD) 300# BLIND RF
LINE BLANK
15 - 350 B564-N10276 150# FIG-8 RF
400 - 600 B564-N10276 150# BLK&SPC RF
GASKET
15 - 600 FLEX.GRAPH.+C276 150# RF 1.6MM
15 - 600 FLEX.GRAPH.+C276 300# RF 1.6MM
BOLT/NUT
GATE
15 - 300 ALLOY C276/C276 150# RF BB OS&Y (09)
GLOBE
15 - 200 ALLOY C276/C276 150# RF BB OS&Y (09)
CHECK
15 - 200 ALLOY C276/C276 150# RF BC SWING (09)
50 - 300 ALLOY C276/C276 150# WAFER DUAL PLATE (09)
2 139/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 01Z0A
RATING ASME 150#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) HOLD
TYPICAL SERVICE DES. PRES.(barg) HOLD
Note :
09
100 All C276 items shall perform SOLUTION ANNEALING
2 140/334
CLASS: 01Z0A
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W W B B
200 W W W W W W W B B
250 W W W W W W W W B B
300 W W W W W W W W W B B
Abbreviation
B Buttwelding Tee
2 141/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B RECL (Hydrogen content to be considered up to 200 ℃ )
PIPE (01,19)
450 - 450 A671-CC65-Cl.22 EFW BE 11.91MM
500 - 500 A671-CC65-Cl.22 EFW BE XS
600 - 600 A671-CC65-Cl.22 EFW BE SCH30
NIPPLE (02,03,19)
SWAGE (02,03,19)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A105 300# SO RF
100 - 600 A105 300# SO RF WITH J.B
15 - 600 A105 300# WN RF (13)
BLIND FLANGE
15 - 600 A105 300# BLIND RF
LINE BLANK
15 - 300 A105 300# FIG-8 FF
350 - 600 A105 300# BLK&SPC FF
GASKET
BOLT/NUT
2 142/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B RECL (Hydrogen content to be considered up to 200 ℃ )
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-119) (09)
CHECK
50 - 600 A216-WCB/13Cr 300# WAFER DUAL PLATE (CH-107) (07,26,63,160)
BALL
BUTTERFLY
PLUG
Note :
05
09
19 Sch 160 pipe and pipe nipples shall be used for threaded connections for sizes 15nb through 40nb.
35
323.2.2 of ASME B31.3.
63 check valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow. Wafer
160 style check valves shall be limited to 260℃ maximum.
2 143/334
CLASS: 03A1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
350 W W W W W W W W W W B B
400 W W W W W W W W W W R B B
450 W W W W W W W W W W R R B B
Abbreviation
B Buttwelding Tee
2 144/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR A MC,MS,N,MCD PWHT / NACE Not required
- LICENSOR B
PIPE (01,19)
450 - 450 A671-CC65-Cl.22 EFW BE 11.91MM
500 - 500 A671-CC65-Cl.22 EFW BE XS
600 - 600 A671-CC65-Cl.22 EFW BE SCH30
NIPPLE (02,03-2,19)
15 - 40 API5L-B-PSL.1 SMLS PBE To match pipe thickness L=3"
15 - 40 API5L-B-PSL.1 SMLS POE/TOE To match pipe thickness L=3"
SWAGE (02,03-2,19)
15 - 40 A234-WPB SMLS PBE To match pipe thickness
50 - 100 A234-WPB SMLS BLE/PSE To match pipe thickness
15 - 40 A105 SW 3000#
CAP
15- 40 A105 THRD 3000#
SOCKOLET/FULL COUPLING (02)
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (02,03-2)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 300# SW RF
50 - 600 A105 300# SO RF
100 - 600 A105 300# SO RF WITH J.B
50 - 600 A105 300# WN RF (13)
25 - 600 A105 600# WN RF (12,82)
50 - 50 A105 1500# WN RTJ
BLIND FLANGE
15 - 600 A105 300# BLIND RF
LINE BLANK
15 - 300 A105 300# FIG-8 FF
GASKET
BOLT/NUT
2 145/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR A MC,MS,N,MCD PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105) (09)
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09,15)
15 - 40 A105/13Cr+HF 800# SW/NPT BB OS&Y (GA-104) (06,09)
GLOBE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GL-101) (09)
CHECK
50 - 600 A216-WCB/13Cr+HF 300# WAFER DUAL PLATE (CH-107) (07,26,63,160)
BALL
BUTTERFLY
PLUG
Notes :
03-2
05
09
35
323.2.2 of ASME B31.3.
2 146/334
CLASS: 03CS1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S W B B
150 S S S S W N B B
250 S S S S W W R R B B
Abbreviation

Buttwelding Tee
2 147/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR A MC,MS,N PWHT / NACE Reqd per B31.3 Sec 331
- LICENSOR B MC,MS,PWF,SGR,CWS,CWR,N for thk > 19.05mm
PIPE (01,19)
300 - 350 API5L-B-PSL.1 SMLS BE XS
450 - 450 A671-CC65-Cl.22 EFW BE 11.91MM
500 - 500 A671-CC65-Cl.22 EFW BE SCH30
600 - 600 A671-CC65-Cl.22 EFW BE SCH30
650 - 650 A671-CC65-Cl.22 EFW BE 15.88MM
700 - 700 A671-CC65-Cl.22 EFW BE 17.48MM
NIPPLE (02,03-2,19)
SWAGE (02,03-2,19)
ELBOW/TEE (02)
15 - 40 A105 SW 3000#
REDUCER
CAP (02)
15 - 40 A105 THRD 3000#
SOCKOLET/FULL COUPLING/UNION/ELBOLET (02)
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (02.03-2)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 300# SW RF
50 - 600 A105 300# SO RF
ASME
650 - 700 A105 300# WN RF (13)
B16.47-A
100 - 600 A105 300# SO RF WITH J.B
WITH J.B
650 - 700 A105 300# WN RF ASME (13)
B16.47-A
50 - 600 A105 300# WN RF (13)
50 - 50 A105 300# WN RF
200 - 450 A105 600# WN RF (12,82)
50 - 50 A105 1500# WN RTJ (12,82)
500 - 500 A105 900# WN RTJ (12,82)
BLIND FLANGE
15 - 600 A105 300# BLIND RF
ASME
650 - 700 A105 300# BLIND RF
B16.47-A
2 148/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
LINE BLANK
15 - 300 A105 300# FIG-8 FF
350 - 600 A105 300# BLK&SPC FF
ASME
650 - 700 A105 300# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
BOLT/NUT
GATE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GA-105)
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (15)
GLOBE
15 - 40 A105/13Cr+HF 800# SW BB OS&Y (GL-101)
CHECK
ASME
(CH-123)
50 - 600 A216-WCB/13Cr 300# WAFER DUAL PLATE (CH-107) (07,26,63,160)
ASME
650 - 700 A216-WCB/13Cr 300# WAFER DUAL PLATE B16.47-A (07,26,63,160)
(CH-124)
BALL
BUTTERFLY
ASME
(BF-105)
80 - 150 A216-WCB/316 300# LUG LEVER (BF-112) (09)
200 - 600 A216-WCB/316 300# LUG GEAR (BF-113) (09)
ASME
650 - 700 A216-WCB/316 300# LUG GEAR B16.47-A (09)
(BF-113)
PLUG
2 149/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
Notes :
03-2
05
09
35
323.2.2 of ASME B31.3.
2 150/334
CLASS: 03CS2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
100 S S S S W B B
Header Size (DN)
150 S S S S W W B B
200 S S S S W W W B B
250 S S S S W W W W B B
300 S S S S W W W W W B B
350 S S S S W W W W W W B B
400 S S S S W W W W W W R B B
450 S S S S W W W W W W R R B B
Abbreviation

Buttwelding Tee
2 151/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B SGS,MLPG
PIPE (01,02)
15 - 20 A333-6 SMLS BE SCH160
25 - 50 A333-6 SMLS BE SCH80
80 - 150 A333-6 SMLS BE SCH40
200 - 200 A333-6 SMLS BE SCH20
250 - 350 A333-6 SMLS BE SCH30
400 - 400 A333-6 SMLS BE SCH40
450 - 600 A333-6 SMLS BE SCH30
NIPPLE (02,03)
15 - 40 A333-6 SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A420-WPL6 SMLS BBE To match pipe thickness
THREDOLET (163)
15 - 40 A350-LF2-Cl.1 THRD 3000#
PLUGS (163)
15 - 40 A350-LF2-Cl.1 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A350-LF2-Cl.1 300# SO RF
100 - 600 A350-LF2-Cl.1 300# SO RF WITH J.B
15 - 600 A350-LF2-Cl.1 300# WN RF (13)
250 - 350 A350-LF2-Cl.1 600# WN RF (12,82)
BLIND FLANGE
15 - 600 A350-LF2-Cl.1 300# BLIND RF
LINE BLANK
15 - 300 A350-LF2-Cl.1 300# FIG-8 FF
350 - 600 A350-LF2-Cl.1 300# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 300# RF 4.5MM (82)
BOLT/NUT
2 152/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B SGS,MLPG
GATE
50 - 80 A352-LCB/316+HF 300# RF BB OS&Y (GA-444)
BB OS&Y SPRING
100 - 250 A352-LCB/316+HF 300# RF (GA-444)
LOADED
300 - 600 A352-LCB/316+HF 300# RF BB OS&Y SP.L GEAR (GA-445)
GLOBE
15 - 40 A350-LF2-Cl.1/316+HF 300# RF BB OS&Y (GL-439)
50 - 80 A352-LCB/316+HF 300# RF BB OS&Y (GL-441)
BB OS&Y SPRING
100 - 200 A352-LCB/316+HF 300# RF (GL-441)
LOADED
250 - 300 A352-LCB/316+HF 300# RF BB OS&Y SP.L GEAR (GL-442)
CHECK
15 - 40 A350-LF2-Cl.1/316+HF 300# RF BC LIFT (CH-439) (61)
50 - 600 A352-LCB/316+HF 300# RF BC SWING (CH-444) (62)
80 - 600 A352-LCB/316 300# WAFER DUAL PLATE (CH-445) (07,26-2,63)
BALL
BUTTERFLY
PLUG
200 - 450 A352-LCB/316+PTFE 300# RF REGULAR GEAR (PL-441) (09)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 153/334
CLASS: 03D1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
Abbreviation
B Buttwelding Tee
2 154/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B RECR,SGR
PIPE (01,02)
150 - 350 A333-6(NACE) SMLS BE SCH40
400 - 450 A333-6(NACE) SMLS BE XS
500 - 600 A333-6(NACE) SMLS BE SCH40
IMPACT
TEST
IMPACT
TEST
IMPACT
TEST
NIPPLE (02,03)
15 - 40 A333-6(NACE) SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A420-WPL6(NACE) SMLS BBE To match pipe thickness
650 - 800 A420-WPL6(NACE) WELD BW To match pipe thickness RT 100%
CAP
THREDOLET (163)
15 - 40 A350-LF2-Cl.1(NACE) THRD 3000#
PLUGS (163)
WELDOLET (02,05)
FLANGE (02)
15 - 600 A350-LF2-Cl.1(NACE) 300# SO RF

ASME
650 - 800 A350-LF2-Cl.1(NACE) 300# WN RF (13)
B16.47-A
100 - 600 A350-LF2-Cl.1(NACE) 300# SO RF WITH J.B
WITH J.B
650 - 800 A350-LF2-Cl.1(NACE) 300# WN RF ASME (13)
B16.47-A
15 - 600 A350-LF2-Cl.1(NACE) 300# WN RF (13)
25 - 450 A350-LF2-Cl.1(NACE) 600# WN RF (12,82)
BLIND FLANGE
ASME
B16.47-A
GASKET
(NACE)
B16.47-A
(NACE)
650 - 800 SW(316+GRAP)IO:316 300# RF 4.5MM ASME (82)
B16.47-A
BOLT/NUT
2 155/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
GATE
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 300# RF BB OS&Y (GA-420) (15)
50 - 250 A352-LCB(NACE)/316+HF 300# RF BB OS&Y (GA-441)
300 - 600 A352-LCB(NACE)/316+HF 300# RF BB OS&Y GEAR (GA-442)
ASME
650 - 800 A352-LCB(NACE)/316+HF 300# RF BB OS&Y GEAR B16.47-A
(GA-443)
GLOBE
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 300# RF BB OS&Y (GL-440)
50 - 200 A352-LCB(NACE)/316+HF 300# RF BB OS&Y (GL-443)
250 - 300 A352-LCB(NACE)/316+HF 300# RF BB OS&Y GEAR (GL-444)
CHECK
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 300# RF BC LIFT (CH-440) (61)
50 - 600 A352-LCB(NACE)/316+HF 300# RF BC SWING (CH-441) (62)
ASME
650 - 800 A352-LCB(NACE)/316+HF 300# RF BC SWING B16.47-A (62)
(CH-443)
ASME
650 - 800 A352-LCB(NACE)/316 300# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-446)
BALL
15 - 150 A352-LCB(NACE)/316+RTFE 300# RF RED. BORE F.S (BA-440) (09)
200 - 600 A352-LCB(NACE)/316+RTFE 300# RF RED. BORE F.S GEAR (BA-442) (09)
ASME
650 - 800 A352-LCB(NACE)/316+RTFE 300# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-444)
15 - 150 A352-LCB(NACE)/316+RTFE 300# RF FULL BORE F.S (BA-441) (08-2,09)
200 - 600 A352-LCB(NACE)/316+RTFE 300# RF FULL BORE F.S GEAR (BA-443) (08-2,09)
ASME
650 - 800 A352-LCB(NACE)/316+RTFE 300# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-445)
BUTTERFLY
80 - 150 A352-LCB(NACE)/316+RTFE 300# LUG LEVER (BF-443) (09)
200 - 600 A352-LCB(NACE)/316+RTFE 300# LUG GEAR (BF-444) (09)
ASME
650 - 800 A352-LCB(NACE)/316+RTFE 300# LUG GEAR B16.47-A (09)
(BF-444)
PLUG
200 - 450 A352-LCB(NACE)/316+PTFE 300# RF REGULAR GEAR (PL-443) (09)
2 156/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
Note :
05
09
35
323.2.2 of ASME B31.3.
2 157/334
CLASS: 03D2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W W B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 158/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 03E1 (ADDED)
RATING ASME 300#
CORR. ALLOWANCE 1.6MM DES. TEMP.(C) 455 to 470
- LICENSOR B DESUPERHEATER DISCHARGE for thk > 12.70mm
PIPE (01)
15 - 40 A335-P11 SMLS BE SCH80
25 - 600 A335-P11 SMLS BE SCH40
1100 - 1100 A691-1.1/4Cr-Cl.22 EFW BE 19.05MM
NIPPLE (02,03)
15 - 40 A335-P11 SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A234-WP11-Cl.1 SMLS BBE To match pipe thickness
15 - 600 A234-WP11-Cl.1 SMLS BW To match pipe thickness
1100 - 1100 A234-WP11-Cl.1 WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 40 A182-F11-Cl.2 THRD 3000#
PLUGS (163)
15 - 40 A182-F11-Cl.2 THRD HEX
WELDOLET (02,05)
50 - 1100 A182-F11-Cl.2 BW To match pipe thickness
FLANGE (02)
15 - 600 A182-F11-Cl.2 300# WN RF
ASME
1100 - 1100 A182-F11-Cl.2 300# WN RF
B16.47-A
25 - 600 A182-F11-Cl.2 300# WN RF WITH J.B
1100 - 1100 A182-F11-Cl.2 300# WN RF
BLIND FLANGE
15 - 600 A182-F11-Cl.2 300# BLIND RF
ASME
1100 - 1100 A182-F11-Cl.2 300# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A182-F11-Cl.2 300# FIG-8 FF
250 - 600 A182-F11-Cl.2 300# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 300# RF 4.5MM
ASME
1100 - 1100 SW(304+GRAP)IO:304 300# RF 4.5MM
B16.47-A
BOLT/NUT
A193-B16/A194-4(Zn-CHROMATE) STUD/H.HEX
Note :
05
2 159/334
CLASS: 03E1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 1100
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
1100 W W W W W W W W W W R R R R R R B
Abbreviation
B Buttwelding Tee
2 160/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B RECR,RECT
PIPE (01,02)
15 - 20 A106-B(NACE) SMLS BE XXS
300 - 350 A106-B(NACE) SMLS BE XS
450 - 600 A333-6(NACE) SMLS BE SCH40
NIPPLE (02,03)
15 - 40 A106-B(NACE) SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A234-WPB(NACE) SMLS BBE To match pipe thickness
THREDOLET (163)
15 - 50 A105(NACE) THRD 3000#
PLUGS (163)
WELDOLET (02,05)
FLANGE (02)
15 - 400 A105(NACE) 300# SO RF
450 - 600 A350-LF2-Cl.1(NACE) 300# SO RF
450 - 600 A350-LF2-Cl.1(NACE) 300# SO RF WITH J.B
15 - 400 A105(NACE) 300# WN RF (13)
450 - 600 A350-LF2-Cl.1(NACE) 300# WN RF (13)
15 - 400 A105(NACE) 300# WN FF (11,13,14)
450 - 600 A350-LF2-Cl.1(NACE) 300# WN FF (11,13,14)
15 - 400 A105(NACE) 600# WN RF (12,13)
450 - 600 A350-LF2-Cl.1(NACE) 600# WN RF (12,13)
BLIND FLANGE
15 - 400 A105(NACE) 300# BLIND RF
15 - 400 A105(NACE) 600# BLIND RF (12)
LINE BLANK
15 - 300 A105(NACE) 300# FIG-8 FF
GASKET
BOLT/NUT
2 161/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B RECR,RECT
GATE
15 - 40 A105(NACE)/13Cr 300# RF BB OS&Y (GA-960) (15)
50 - 250 A216-WCB(NACE)/13Cr 300# RF BB OS&Y (GA-961)
300 - 600 A216-WCB(NACE)/13Cr 300# RF BB OS&Y GEAR (GA-962)
15 - 40 A105(NACE)/13Cr 300# RF BB OS&Y (GA-960A)
GLOBE
15 - 40 A105(NACE)/13Cr 300# RF BB OS&Y (GL-960)
50 - 200 A216-WCB(NACE)/13Cr 300# RF BB OS&Y (GL-961)
250 - 300 A216-WCB(NACE)/13Cr 300# RF BB OS&Y GEAR (GL-962)
CHECK
15 - 40 A105(NACE)/13Cr 300# RF BC LIFT (CH-960) (61)
50 - 600 A216-WCB(NACE)/13Cr 300# RF BC SWING (CH-961) (62)
50 - 600 A216-WCB(NACE)/13Cr 300# WAFER DUAL PLATE (CH-962) (07,26-2,63,160)
BUTTERFLY
80 - 150 A216-WCB(NACE)/316 300# LUG LEVER (BF-960) (09)
200 - 600 A216-WCB(NACE)/316 300# LUG GEAR (BF-961) (09)
BALL
15 - 40 A216-WCB(NACE)/316 300# RF RED. BORE F.S (BA-960) (09)
50 - 150 A216-WCB(NACE)/316 300# RF RED. BORE F.S (BA-961) (09)
200 - 600 A216-WCB(NACE)/316 300# RF RED. BORE F.S GEAR (BA-963) (09)
80 - 150 A216-WCB(NACE)/316 300# RF FULL BORE F.S (BA-962) (08-2,09)
200 - 600 A216-WCB(NACE)/316 300# RF FULL BORE F.S GEAR (BA-964) (08-2,09)
Note :
05
09
2 162/334
CLASS: 03G2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
Abbreviation
B Buttwelding Tee
2 163/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B DW
PIPE (01)
15 - 20 A312-TP304/304L SMLS PE SCH80S
25 - 40 A312-TP304/304L SMLS PE SCH40S
50 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH30
350 - 400 A358-304/304L-Cl.1 EFW BE SCH20
450 - 450 A358-304/304L-Cl.1 EFW BE 8.74MM
500 - 500 A358-304/304L-Cl.1 EFW BE 10.31MM
600 - 600 A358-304/304L-Cl.1 EFW BE XS
650 - 650 A358-304/304L-Cl.1 EFW BE SCH20
700 - 750 A358-304/304L-Cl.1 EFW BE 14.27MM
800 - 800 A358-304/304L-Cl.1 EFW BE SCH30
NIPPLE (02)
SWAGE (02)
15 - 40 A182-F304/304L SW 3000#
CAP (02)
15 - 40 A182-F304/304L SW 3000#
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (02)
15 - 40 A182-F304/304L THRD HEX
15 - 40 A182-F304/304L SW 3000#
WELDOLET (02,81)
FLANGE (02)
15 - 40 A182-F304/304L 300# SW RF
50 - 600 A182-F304/304L 300# WN RF
ASME
650 - 800 A182-F304/304L 300# WN RF
B16.47-A
100 - 600 A182-F304/304L 300# WN RF WITH J.B
WITH J.B
650 - 800 A182-F304/304L 300# WN RF ASME
B16.47-A
BLIND FLANGE
15 - 600 A182-F304/304L 300# BLIND RF
ASME
650 - 800 A182-F304/304L 300# BLIND RF
B16.47-A
LINE BLANK
15 - 300 A182-F304/304L 300# FIG-8 FF
350 - 600 A182-F304/304L 300# BLK&SPC FF
ASME
650 - 800 A182-F304/304L 300# BLK&SPC FF
B16.47-A
2 164/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B DW
GASKET
ASME
B16.47-A
BOLT/NUT
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201)
50 - 250 A351-CF8M/316 300# RF BB OS&Y (GA-207) (06)
300 - 600 A351-CF8M/316 300# RF BB OS&Y GEAR (GA-208) (06)
ASME
650 - 800 A351-CF8M/316 300# RF BB OS&Y GEAR B16.47-A (06)
(GA-235)
15 - 40 A182-F316/316 300# RF BB OS&Y (GA-206) (06)
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y (GA-204) (06)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-204)
50 - 200 A351-CF8M/316 300# RF BB OS&Y (GL-205)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-204) (61)
ASME
(CH-225)
ASME
(CH-226)
BALL
ASME
(BA-231)
ASME
(BA-232)
BUTTERFLY
ASME
(BF-244)
ASME
(BF-245)
2 165/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B DW
Notes :
09
62 These check valves shall be installed in a horizontal position with cover up or in a vertical position with upward flow. These check
63 valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow. Integrally reinforced
81 branch connections, tees, and reducing tees are permitted as an acceptable alternative branch connection. These items shall be
163 used only for hydrotest vent/drain.
2 166/334
CLASS: 03SA0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
Header Size (DN)
250 W W W W W N N R B B
300 W W W W W R R R R B B
350 W W W W W R R R R R B B
Abbreviation
B Buttwelding Tee
2 167/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR A NOT USED PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 40 A312-TP304/304L SMLS PE SCH40S
50 - 300 A312-TP304/304L SMLS BE SCH40S
350 - 350 A312-TP304/304L DSAW BE SCH40S
400 - 600 A312-TP304/304L DSAW BE SCH40
NIPPLE (02)
SWAGE (02)
15 - 40 A182-F304/304L SW 3000#
CAP (02)
15 - 40 A182-F304/304L SW 3000#
FULL COUPLING/SOCKOLET (02)
15 - 40 A182-F304/304L SW 3000#
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (02)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 40 A182-F304/304L 300# SW RF
50 - 600 A182-F304/304L 300# WN RF
100 - 600 A182-F304/304L 300# WN RF WITH J.B
50 - 50 A182-F304/304L 1500# WN RTJ (82)
80 - 350 A182-F304/304L 900# WN RTJ (82)
BLIND FLANGE
15 - 600 A182-F304/304L 300# BLIND RF
GASKET
BOLT/NUT
2 168/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR A NOT USED PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201) (09)
50 - 250 A351-CF8M/316 300# RF BB OS&Y (GA-219) (08-2,09)
15 - 40 A182-F316/316L 800# SW/NPT BB OS&Y (GA-204) (06,09)
15 - 40 A182-F316/316 300# RF BB OS&Y (GA-207) (08-2)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-204) (09)
50 - 200 A351-CF8M/316 300# RF BB OS&Y (GL-205) (09)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-204) (61)
BALL
BUTTERFLY
Notes :
09
2 169/334
CLASS: 03SS
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S W B B
150 S S S S W N B B
250 S S S S W W R R B B
Abbreviation

Buttwelding Tee
2 170/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B PW,RECT (-46 ℃ to 300 ℃ (max 800nb))
PIPE (01)
15 - 20 A312-TP304/304L SMLS BE SCH80S
25 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH30
350 - 400 A358-304/304L-Cl.1 EFW BE SCH20
450 - 450 A358-304/304L-Cl.1 EFW BE 8.74MM
500 - 500 A358-304/304L-Cl.1 EFW BE 10.31MM
600 - 600 A358-304/304L-Cl.1 EFW BE XS
650 - 650 A358-304/304L-Cl.1 EFW BE SCH20
700 - 750 A358-304/304L-Cl.1 EFW BE 14.27MM
800 - 800 A358-304/304L-Cl.1 EFW BE SCH30
NIPPLE (02,03)
SWAGE (02,03)
WELDOLET (02,81)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (02)
15 - 40 A182-F304/304L THRD HEX
FLANGE (02)
15 - 600 A182-F304/304L 300# WN RF
ASME
650 - 800 A182-F304/304L 300# WN RF
B16.47-A
100 - 600 A182-F304/304L 300# WN RF WITH J.B
WITH J.B
650 - 800 A182-F304/304L 300# WN RF ASME
B16.47-A
15 - 150 A182-F304/304L 600# WN RF (82)
BLIND FLANGE
15 - 600 A182-F304/304L 300# BLIND RF
ASME
650 - 800 A182-F304/304L 300# BLIND RF
B16.47-A
LINE BLANK
15 - 300 A182-F304/304L 300# FIG-8 FF
350 - 600 A182-F304/304L 300# BLK&SPC FF
ASME
650 - 800 A182-F304/304L 300# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
BOLT/NUT
2 171/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
VALVES FOR FLUID : PW, RECT (Operation between -46℃ and 300℃) Linde fluidd group 001
GATE
15 - 40 A182-F316/316 800# SW BB OS&Y (GA-201) (09)
50 - 250 A351-CF8M/316 300# RF BB OS&Y (GA-219) (08-2,09)
ASME
(GA-235)
15 - 40 A182-F316/316 800# SW/NPT BB OS&Y (GA-204) (06,09)
15 - 40 A182-F316/316 300# RF BB OS&Y (GA-206) (09)
GLOBE
15 - 40 A182-F316/316 800# SW BB OS&Y (GL-204) (09)
50 - 200 A351-CF8M/316 300# RF BB OS&Y (GL-205) (09)
CHECK
15 - 40 A182-F316/316 800# SW BC LIFT (CH-204) (61)
ASME
(CH-225)
ASME
(CH-226)
BUTTERFLY
ASME
(BF-244)
ASME
(BF-245)
BALL
ASME
(BA-231)
ASME
(BA-232)
2 172/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
Note :
09
2 173/334
CLASS: 03U0B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 174/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
CORR. ALLOWANCE 0.0MM DES. TEMP.(C) -196 to -47
- LICENSOR B SGR,RP,RECR (-196 ℃ to 210 ℃ (max 600nb))
PIPE (01)
15 - 20 A312-TP304/304L SMLS BE SCH80S
25 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH30
350 - 400 A358-304/304L-Cl.1 EFW BE SCH20
450 - 450 A358-304/304L-Cl.1 EFW BE 8.74MM
500 - 500 A358-304/304L-Cl.1 EFW BE 10.31MM
600 - 600 A358-304/304L-Cl.1 EFW BE XS
650 - 650 A358-304/304L-Cl.1 EFW BE SCH20
700 - 750 A358-304/304L-Cl.1 EFW BE 14.27MM
800 - 800 A358-304/304L-Cl.1 EFW BE SCH30
900 - 900 A358-304/304L-Cl.1 EFW BE 17.48MM
NIPPLE (02,03)
SWAGE (02,03)
CAP (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (02)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F304/304L 300# WN RF
ASME
650 - 900 A182-F304/304L 300# WN RF
B16.47-A
100 - 600 A182-F304/304L 300# WN RF WITH J.B
WITH J.B
650 - 900 A182-F304/304L 300# WN RF ASME
B16.47-A
25 - 150 A182-F304/304L 600# WN RF (82)
BLIND FLANGE
15 - 600 A182-F304/304L 300# BLIND RF
ASME
650 - 900 A182-F304/304L 300# BLIND RF
B16.47-A
LINE BLANK
15 - 300 A182-F304/304L 300# FIG-8 FF
350 - 600 A182-F304/304L 300# BLK&SPC FF
ASME
650 - 900 A182-F304/304L 300# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
BOLT/NUT
2 175/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
VALVES FOR FLUID : SGR, RP (Operating below -46℃) Linde fluid groups 038(RECR), and 016(RP)
GATE
EXTENDED
15 - 40 A182-F316/316+RTFE 800# SW BB OS&Y BONNET
(GA-250)
EXTENDED
50 - 250 A351-CF8M/316+RTFE 300# RF BB OS&Y BONNET (08-2,09)
(GA-258)
EXTENDED
300 - 600 A351-CF8M/316+RTFE 300# RF BB OS&Y GEAR BONNET (08-2,09)
(GA-259)
ASME
B16.47-A
750 - 750 A351-CF8M/316+RTFE 300# RF BB OS&Y GEAR EXTENDED
BONNET
(GA-259A)
EXTENDED
15 - 40 A182-F316/316+RTFE 800# SW/NPT BB OS&Y BONNET (06,09)
(GA-257)
EXTENDED
15 - 40 A182-F316/316+RTFE 300# RF BB OS&Y BONNET (09)
(GA-251)
GLOBE
EXTENDED
(GL-250)
EXTENDED
(GL-254)
EXTENDED
(GL-255)
BUTTERFLY
EXTENDED
50 - 150 A351-CF8M/316+RTFE 300# WAFER LEVER BONNET (07,09)
(BF-254)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 300# WAFER GEAR BONNET (07,09)
(BF-255)
EXTENDED
50 - 150 A351-CF8M/316+RTFE 300# LUG LEVER BONNET (07,09)
(BF-256)
EXTENDED
200 - 600 A351-CF8M/316+RTFE 300# LUG GEAR BONNET (07,09)
(BF-257)
BALL
EXTENDED
(BA-358)
EXTENDED
(BA-360)
EXTENDED
(BA-359)
EXTENDED
(BA-361)
2 176/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
VALVES FOR FLUID : RECR (Operating below -46℃) IN CORROSIVE SERVICE Linde fluid group 034
GATE
EXTENDED
(GA-276)
EXTENDED
(GA-283)
EXTENDED
BB OS&Y SPRING
100 - 250 A351-CF8M/316 300# RF BONNET (08-2,09)
LOADED
(GA-283)
EXTENDED
(GA-284)
GLOBE
EXTENDED
(GL-275)
EXTENDED
(GL-279)
EXTENDED
BB OS&Y SPRING
100 - 200 A351-CF8M/316 300# RF BONNET (09)
LOADED
(GL-279)
EXTENDED
(GL-280)
CHECK
15 - 40 A182-F316/316 300# RF BC LIFT (CH-383) (61)
ASME
650 - 750 A351-CF8M/316 300# WAFER DUAL PLATE B16.47- (07,26,63)
A(CH-385)
Note :
09
2 177/334
CLASS: 03U0C
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W W B B
150 W W W W W N B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 178/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 03X1
RATING ASME 300#
- LICENSOR B SGS
PIPE (01,02)
15 - 20 A106-B SMLS BE SCH160
25 - 50 A106-B SMLS BE SCH80
80 - 200 A106-B SMLS BE SCH40
250 - 400 A333-6 SMLS BE SCH40
450 - 450 A333-6 SMLS BE XS
500 - 600 A333-6 SMLS BE SCH40
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 200 A105 300# SO RF
250 - 600 A350-LF2-Cl.1 300# SO RF
100 - 200 A105 300# SO RF WITH J.B
15 - 200 A105 300# WN RF (13)
250 - 600 A350-LF2-Cl.1 300# WN RF (13)
15 - 200 A105 300# WN FF (11,13,14)
250 - 600 A350-LF2-Cl.1 300# WN FF (11,13,14)
15 - 200 A105 600# WN RF (12,13)
250 - 600 A350-LF2-Cl.1 600# WN RF (12,13)
BLIND FLANGE
15 - 200 A105 300# BLIND RF
250 - 600 A350-LF2-Cl.1 300# BLIND RF
15 - 200 A105 600# BLIND RF (12)
250 - 600 A350-LF2-Cl.1 600# BLIND RF (12)
LINE BLANK
15 - 200 A105 300# FIG-8 FF
250 - 300 A350-LF2-Cl.1 300# FIG-8 FF
350 - 600 A350-LF2-Cl.1 300# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (82)
BOLT/NUT
2 179/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B SGS
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09,15)
(GA-108)
WITH BY
500 - 500 A216-WCB/13Cr+HF 300# RF BB OS&Y GEAR PASS DN20 (09)
GLOBE
V/V(GL-102)
GLOBE
REFERENCE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (09)
(GL-104)
CHECK
50 - 600 A216-WCB/13Cr 300# WAFER DUAL PLATE (CH-107) (07,26-2,63,160)
BALL
BUTTERFLY
80 - 150 A216-WCB/316 300# LUG LEVER (BF-112) (09)
200 - 600 A216-WCB/316 300# LUG GEAR (BF-113) (09)
Note :
05
09
2 180/334
CLASS: 03X1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
Abbreviation
B Buttwelding Tee
2 181/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B SGS,PGM
PIPE (01,02)
25 - 40 A106-B SMLS BE SCH160
50 - 150 A106-B SMLS BE SCH80
200 - 200 A106-B SMLS BE SCH60
250 - 250 A333-6 SMLS BE SCH60
300 - 350 A333-6 SMLS BE XS
400 - 600 A333-6 SMLS BE SCH40
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 200 A105 300# SO RF
250 - 600 A350-LF2-Cl.1 300# SO RF
100 - 200 A105 300# SO RF WITH J.B
15 - 200 A105 300# WN RF (13)
250 - 600 A350-LF2-Cl.1 300# WN RF (13)
15 - 200 A105 300# WN FF (11,13,14)
250 - 600 A350-LF2-Cl.1 300# WN FF (11,13,14)
15 - 600 A105 600# WN RF (12,13)
BLIND FLANGE
15 - 600 A105 300# BLIND RF
15 - 600 A105 600# BLIND RF (12)
LINE BLANK
15 - 200 A105 300# FIG-8 FF
250 - 300 A350-LF2-Cl.1 300# FIG-8 FF
350 - 600 A350-LF2-Cl.1 300# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (12)
BOLT/NUT
2 182/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B SGS,PGM
GATE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GA-106) (09,15)
BB OS&Y SPRING
100 - 250 A216-WCB/13Cr+HF 300# RF (GA-137) (09)
LOADED
300 - 600 A216-WCB/13Cr+HF 300# RF BB OS&Y SP.L GEAR (GA-138) (09)
(GA-137)
WITH BY
BB OS&Y SPRING
100 - 250 A216-WCB/13Cr+HF 300# RF PASS DN20 (09)
LOADED
GLOBE
V/V(GL-101)
GLOBE
15 - 40 A105/13Cr+HF 300# RF BB OS&Y (GL-119) (09)
BB OS&Y SPRING
50 - 200 A216-WCB/13Cr+HF 300# RF (GL-144) (09)
LOADED
250 - 300 A216-WCB/13Cr+HF 300# RF BB OS&Y SP.L GEAR (GL-145) (09)
CHECK
50 - 600 A216-WCB/13Cr 300# WAFER DUAL PLATE (CH-107) (07,26-2,63,160)
BALL
BUTTERFLY
80 - 150 A216-WCB/316 300# LUG LEVER (BF-112) (09)
200 - 600 A216-WCB/316 300# LUG GEAR (BF-113) (09)
Note :
05
09
63 check valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow. Wafer
160 style check valves shall be limited to 260℃ maximum.
2 183/334
CLASS: 03X2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W W B B
150 W W W W W W B B
Abbreviation
B Buttwelding Tee
2 184/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B PCR
PIPE (01,100)
15 - 20 A790-S31803 SMLS BE SCH80S
25 - 150 A790-S31803 SMLS BE SCH40S
200 - 250 A790-S31803 SMLS BE SCH10S
300 - 600 A790-S31803 SMLS BE SCH20
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F51 THRD 3000#
PLUGS (163)
15 - 40 A182-F51 THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F51 300# WN RF
100 - 600 A182-F51 300# WN RF WITH J.B
15 - 250 A182-F51 600# WN RF (82)
BLIND FLANGE
15 - 600 A182-F51 300# BLIND RF
LINE BLANK
15 - 300 A182-F51 300# FIG-8 FF
350 - 600 A182-F51 300# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 300# RF 4.5MM
BOLT/NUT
GATE
GLOBE
CHECK
15 - 40 A351-CD4MCu/DUPLEX 2205 300# BW BC LIFT (CH-601) (61)
2 185/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 300#
- LICENSOR B PCR
Note :
09
2 186/334
CLASS: 03Y0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
Header Size (DN)
100 W W W W R B B
150 W W W W R R B B
200 W W W W R R R B B
250 W W W W R R R R B B
300 W W W W R R R R R B B
350 W W W W R R R R R R B B
Abbreviation
B Buttwelding Tee
2 187/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A WWG PWHT / NACE Not required
- LICENSOR B
PIPE (01,100)
15 - 20 A790-S32750 SMLS BE SCH160
25 - 40 A790-S32750 SMLS BE SCH80S
50 - 250 A790-S32750 SMLS BE SCH40S
300 - 300 A790-S32750 SMLS BE SCH80S
350 - 400 A790-S32750 DSAW BE SCH80S
450 - 450 A790-S32750 DSAW BE SCH40
500 - 500 A790-S32750 DSAW BE 15.88MM
600 - 600 A790-S32750 DSAW BE 19.05MM
NIPPLE (02,114)
SWAGE (02,114)
350 - 600 A815-S32750 WELD BW To match pipe thickness
THREDOLET (163)
15 - 40 A182-F53 THRD 3000#
PLUGS (163)
15 - 40 A182-F53 THRD HEX
FLANGE (02)
15 - 600 A182-F53 600# WN RF
100 - 600 A182-F53 600# WN RF WITH J.B
BLIND FLANGE
15 - 600 A182-F53 600# BLIND RF
LINE BLANK
15 - 200 A182-F53 600# FIG-8 FF
250 - 600 A182-F53 600# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 600# RF 4.5MM
BOLT/NUT
GATE
15 - 40 A182-F53/DUPLEX 2507 600# RF BB OS&Y (GA-310) (09)
GLOBE
15 - 40 A182-F53/DUPLEX 2507 600# RF BB OS&Y (GL-310) (09)
CHECK
15 - 40 A182-F53/DUPLEX 2507 600# BW BC LIFT (CH-310) (61)
50 - 600 A351-CF8M/DUPLEX 2507 600# RF BC SWING (CH-311) (62)
50 - 600 A351-CF8M/DUPLEX 2507 600# WAFER DUAL PLATE (CH-312) (07,26,63)
2 188/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A WWG PWHT / NACE Not required
- LICENSOR B
Note :
09
63 check valves shall be installed in a horizontal position with hinge pin vertical or a vertical position with upward flow. Not to be
100 used over 315℃.
2 189/334
CLASS: 06B1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
250 W W W W W W W B B B
300 W W W W W W W W B B B
350 W W W W W W W W W B B B
400 W W W W W W W W W W B B B
450 W W W W W W W W W W W B B B
500 W W W W W W W W W W W W B B B
600 W W W W W W W W W W W W W B B B
Abbreviation
B Buttwelding Tee
2 190/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A HGOX,WOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
PIPE
15 - 40 A312-TP304/304L SMLS BE SCH80S (01,99,103)
50 - 100 A312-TP304/304L SMLS BE SCH40S
150 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH80
350 - 600 A312-TP304/304L DSAW BE SCH80
BEND (02,103)
NIPPLE (02,103)
SWAGE (02,103)
CAP (02,103)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
FLANGE (02,103)
15 - 600 A182-F304/304L 600# WN RF
100 - 600 A182-F304/304L 600# WN RF WITH J.B
BLIND FLANGE (103)
15 - 600 A182-F304/304L 600# BLIND RF
GASKET
OXYGEN
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM (105)
SERVICE
BOLT/NUT
GATE
15 - 40 A182-F316/ALLOY 400 600# RF BB OS&Y (GA-221) (08-3,09)
50 - 250 A351-CF8M/ALLOY 400 600# RF BB OS&Y (GA-227) (08-3,09)
300 - 600 A351-CF8M/ALLOY 400 600# RF BB OS&Y GEAR (GA-222) (08-3,09)
GLOBE
15 - 40 A182-F316/ALLOY 400 600# RF BB OS&Y (GL-221) (08-3,09)
50 - 100 A351-CF8M/ALLOY 400 600# RF BB OS&Y (GL-229) (08-3,09)
150 - 300 A351-CF8M/ALLOY 400 600# RF BB OS&Y GEAR (GL-222) (08-3,09)
CHECK
15 - 40 A182-F316/ALLOY 400 600# RF BC SWING (CH-242) (62)
50 - 600 A351-CF8M/ALLOY 400 600# RF BC SWING (CH-248) (62)
50 - 600 A351-CF8M/ALLOY 400 600# WAFER DUAL PLATE (CH-243) (07,26,63)
BALL
15 - 100 A351-CF8M/ALLOY 400+RTFE 600# RF FULL BORE F.S (BA-242) (09)
150 - 600 A351-CF8M/ALLOY 400+RTFE 600# RF FULL BORE F.S GEAR (BA-243) (08-3,09)
2 191/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A HGOX,WOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
Notes :
09
35
323.2.2 of ASME B31.3.
102
2 192/334
CLASS: 06C0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 193/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A SLU PWHT / NACE Not required
- LICENSOR B
PIPE (01,110)
25 - 50 A312-TP304/304L SMLS BE SCH160
80 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH80
BEND (02,114)
50 - 200 A312-TP304/304L SMLS BE SCH160 3D (110,111)
50 - 200 A312-TP304/304L SMLS BE SCH160 5D (110,111)
NIPPLE (02,114)
ELBOW/TEE/REDUCER/LATERAL/CAP (02,114)
LATROLET (02,81,114)
FLANGEOLET (02,81,114)
THREDOLET (163)
25 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
25 - 40 A182-F304/304L THRD HEX
STUB-END (02,114)
25 -300 A403-WP304/304L SMLS BW To match pipe thickness LONG
PATTERN
FLANGE (02)
25 - 300 A105(GALV) 600# LJ
100 - 300 A105(GALV) 600# LJ WITH J.B
25 - 300 A182-F304/304L 600# WN RF (82)
25 - 200 A182-F304/304L 600# WN FF (82)
50 - 50 A182-F304/304L 1500# WN RF (82)
80 - 300 A182-F304/304L 900# WN RF (82)
80 - 200 A182-F304/304L 900# WN SCH80S RTJ (82)
80 - 200 A105(GALV) 900# LJ (82)
50 - 80 A182-F304/304L 1500# WN SCH160 RF (82)
BLIND FLANGE
25 - 300 A182-F304/304L 600# BLIND RF
GASKET
25 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
50 - 50 SW(304+GRAP)IO:304 1500# RF 4.5MM (82)
80 - 80 SW(304+GRAP)IO:304 900# RF 4.5MM (82)
80 - 80 SS304/304L 900# RTJ OVAL RING (82)
50 - 50 SW(304+GRAP)IO:304 1500# RF 4.5MM (82)
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 194/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B
GATE
50 - 150 A216-WCB/13Cr+HF 600# RF BB OS&Y (GA-127) (08,09)
CHECK
50 - 150 A216-WCB/13Cr+HF 600# LUG DUAL PLATE (CH-115) (08,09)
REFERENCE
50 - 80 A216-WCB/13Cr+HF 600# RF BC BALL
(CH-116)
BALL
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S (BA-220) (08,09)
150 - 200 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S GEAR (BA-221) (08,09)
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL F.S EXT.BONNET (BA-220E) (08,09)
Notes :
08
09
110
111
2 195/334
CLASS: 06C2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 196/334
CLASS: 06C2 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 197/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A MBFW,HFG,HCD,HN PWHT / NACE Reqd per B31.3 Sec 331
- LICENSOR B for thk > 19.05mm
PIPE (01,19)
15 - 20 A106-B SMLS PE SCH160
25 - 40 A106-B SMLS PE SCH80
50 - 600 A106-B SMLS BE SCH80
BEND
150 - 600 A106-B SMLS BE SCH80 R=3D
NIPPLE (02)
15 - 40 A106-B SMLS PBE To match pipe thickness L=3" (03-2,19)
15 - 40 A106-B SMLS POE/TOE To match pipe thickness L=3" (03-2,19)
SWAGE (02)
15 - 40 A234-WPB SMLS PBE To match pipe thickness (03-2,19)
50 - 100 A234-WPB SMLS BLE/PSE To match pipe thickness (03-2,19)
15 - 40 A105 SW 3000#
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (02)
15 - 40 A105 THRD HEX (03-2)
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 600# SW RF
50 - 600 A105 600# WN RF
100 - 600 A105 600# WN RF WITH J.B
15 - 40 A105 1500# SW RJT (82)
80 - 600 A105 900# WN RJT (82)
50 - 600 A105 1500# WN RJT (82)
BLIND FLANGE
15 - 600 A105 600# BLIND RF
LINE BLANK
15 - 200 A105 600# FIG-8 FF
250 - 600 A105 600# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
15 - 50 SOFT IRON 1500# RJT OVAL RING (82)
80 - 600 SOFT IRON 900# RJT OVAL RING (82)
BOLT/NUT
2 198/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A MBFW,HFG,HCD,HN PWHT / NACE Reqd per B31.3 Sec 331
GATE
15 - 40 A105/S&D HF 800# SW BB OS&Y (GA-110)
50 - 250 A216-WCB/S&D HF 600# RF BB OS&Y (GA-112) (15)
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y GEAR (GA-113) (15)
50 - 250 A216-WCB/S&D HF 600# BW BB OS&Y (GA-114) (15)
300 - 600 A216-WCB/S&D HF 600# BW BB OS&Y GEAR (GA-115) (15)
15 - 40 A105/S&D HF 600# RF BB OS&Y (GA-111) (15)
15 - 40 A105/S&D HF 800# SW/NPT BB OS&Y (GA-109) (06)
GLOBE
15 - 40 A105/S&D HF 800# SW BB OS&Y (GL-106) (09)
50 - 100 A216-WCB/S&D HF 600# RF BB OS&Y (GL-107) (09)
150 - 300 A216-WCB/S&D HF 600# RF BB OS&Y GEAR (GL-108) (09)
CHECK
15 - 40 A105/S&D HF 800# SW BC LIFT (CH-108) (61)
50 - 600 A216-WCB/S&D HF 600# BW BC SWING (CH-109) (62)
WITH
15 - 40 A105/S&D HF 800# SW BC LIFT SPRING (62)
(CH-130)
50 - 150 A216-WCB/S&D HF 600# RF BC LIFT (CH-108L) (61)
BALL
Notes :
03-2
05
06 These valves shall be used only for vent, drain and instrument connections.
09
2 199/334
CLASS: 06CS1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S B B B
150 S S S S W B B B
200 S S S S W W B B B
250 S S S S W W W B B B
300 S S S S W W W W B B B
350 S S S S W W W W W B B B
400 S S S S W W W W W W B B B
450 S S S S W W W W W W W B B B
500 S S S S W W W W W W W W B B B
600 S S S S W W W W W W W W W B B B
Abbreviation

Buttwelding Tee
2 200/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B CWS,CWR,BD,HS,HIS for thk > 19.05mm
PIPE (01,27)
15 - 20 A106-B SMLS PE XXS
25 - 40 A106-B SMLS PE SCH160
50 - 80 A106-B SMLS BE SCH160
100 - 150 A106-B SMLS BE SCH120
200 - 300 A106-B SMLS BE SCH100
350 - 600 A106-B SMLS BE SCH80
NIPPLE (02)
15 - 40 A106-B SMLS PBE To match pipe thickness L=3" (03-2)
15 - 40 A106-B SMLS POE/TOE To match pipe thickness L=3" (03-2)
SWAGE (02)
15 - 40 A105 SW 3000#
CAP (02)
15 - 40 A105 THRD 3000#
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 40 A105 600# SW RF
50 - 600 A105 600# WN RF
100 - 600 A105 600# WN RF WITH J.B
15 - 20 A105 1500# SW RTJ (82)
50 - 50 A105 1500# WN RTJ (82)
80 - 200 A105 900# WN RTJ (82)
BLIND FLANGE
15 - 600 A105 600# BLIND RF
LINE BLANK
15 - 200 A105 600# FIG-8 FF
250 - 600 A105 600# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
2 201/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B CWS,CWR,BD,HS,HIS for thk > 19.05mm
GATE
15 - 40 A105/S&D HF 800# SW BB OS&Y (GA-110) (09)
50 - 250 A216-WCB/S&D HF 600# RF BB OS&Y (GA-112) (09)
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y GEAR (GA-113) (09)
15 - 40 A105/S&D HF 600# RF BB OS&Y (GA-111) (09)
15 - 40 A105/S&D HF 800# SW/NPT BB OS&Y (GA-109) (06,09)
GLOBE
15 - 40 A105/S&D HF 800# SW BB OS&Y (GL-106) (09)
BLOW DOWN
15 - 40 A105/S&D HF 800# SW BB OS&Y
CHECK
REFERENCE
50 - 600 A216-WCB/S&D HF 600# BW BC BALL (62)
(CH-109)
BALL
Notes :
03-2
05
06 These valves shall be used only for vent, drain and instrument connections.
09
Pipe and pipe components thicker than 12.7mm may require impact tested materials if the MDMT is below 38℃. See the ASME
27
B31.3 Paragraph 323.2.2
35
323.2.2 of ASME B31.3.
2 202/334
CLASS: 06CS2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S B B B
150 S S S S W B B B
250 S S S S W W W B B B
300 S S S S W W W W B B B
350 S S S S W W W W W B B B
400 S S S S W W W W W W B B B
450 S S S S W W W W W W W B B B
500 S S S S W W W W W W W W B B B
600 S S S S W W W W W W W W W B B B
Abbreviation

Buttwelding Tee
2 203/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGS (Hydrogen content to be considered up to 200 C),HLPG
PIPE (01,02)
15 - 20 A333-6 SMLS BE SCH160
25 - 600 A333-6 SMLS BE SCH80
NIPPLE (02,03)
15 - 40 A333-6 SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A420-WPL6 SMLS BBE To match pipe thickness
THREDOLET (163)
15 - 40 A350-LF2-Cl.1 THRD 3000#
PLUGS (163)
15 - 40 A350-LF2-Cl.1 THRD HEX
WELDOLET (02,05)
FLANGE (02,13)
15 - 600 A350-LF2-Cl.1 600# WN RF
100 - 600 A350-LF2-Cl.1 600# WN RF WITH J.B
BLIND FLANGE
15 - 600 A350-LF2-Cl.1 600# BLIND RF
LINE BLANK
15 - 200 A350-LF2-Cl.1 600# FIG-8 FF
250 - 600 A350-LF2-Cl.1 600# BLK&SPC FF
GASKET
15 - 600 SW(316+GRAP)IO:316 600# RF 4.5MM
BOLT/NUT
GATE
50 - 80 A352-LCB/316+HF 600# RF BB OS&Y (GA-461) (09)
BB OS&Y SPRING
100 - 250 A352-LCB/316+HF 600# RF (GA-461) (09)
LOADED
300 - 600 A352-LCB/316+HF 600# RF BB OS&Y SP.L GEAR (GA-462) (09)
GLOBE
15 - 40 A350-LF2-Cl.1/316+HF 600# RF BB OS&Y (GL-459) (09)
50 - 80 A352-LCB/316+HF 600# RF BB OS&Y (GL-461) (09)
BB OS&Y SPRING
100 - 100 A352-LCB/316+HF 600# RF (GL-461) (09)
LOADED
150 - 300 A352-LCB/316+HF 600# RF BB OS&Y SP.L GEAR (GL-462) (09)
CHECK
15 - 40 A350-LF2-Cl.1/316+HF 600# BW BC LIFT (CH-479) (61)
50 - 600 A352-LCB/316+HF 600# RF BC SWING (CH-461) (62)
80 - 600 A352-LCB/316+HF 600# WAFER DUAL PLATE (CH-462) (07,26-2,63)
BALL
BUTTERFLY
2 204/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGS (Hydrogen content to be considered up to 200 C),HLPG
Notes :
05
09
35 323.2.2 of ASME B31.3.
2 205/334
CLASS: 06D1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 206/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
PIPE (01,02)
NIPPLE (02,03)
15 - 40 A333-6(NACE) SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A420-WPL6(NACE) SMLS BBE To match pipe thickness
THREDOLET (163)
15 - 40 A350-LF2-Cl.1(NACE) THRD 3000#
PLUGS (163)
WELDOLET (02,05)
FLANGE (02,13)
15 - 600 A350-LF2-Cl.1(NACE) 600# WN RF
100 - 600 A350-LF2-Cl.1(NACE) 600# WN RF WITH J.B
BLIND FLANGE
LINE BLANK
15 - 200 A350-LF2-Cl.1(NACE) 600# FIG-8 FF
GASKET
BOLT/NUT
GATE
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 600# RF BB OS&Y (GA-460) (09)
50 - 250 A352-LCB(NACE)/316+HF 600# RF BB OS&Y (GA-481) (09)
300 - 600 A352-LCB(NACE)/316+HF 600# RF BB OS&Y GEAR (GA-482) (09)
GLOBE
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 600# RF BB OS&Y (GL-460) (09)
50 - 100 A352-LCB(NACE)/316+HF 600# RF BB OS&Y (GL-481) (09)
150 - 300 A352-LCB(NACE)/316+HF 600# RF BB OS&Y GEAR (GL-482) (09)
CHECK
15 - 40 A350-LF2-Cl.1(NACE)/316+HF 600# BW BC LIFT (CH-480) (61)
50 - 600 A352-LCB(NACE)/316 600# RF BC SWING (CH-481) (62)
BALL
15 - 100 A352-LCB(NACE)/316+RTFE 600# RF RED. BORE F.S (BA-480) (09)
150 - 600 A352-LCB(NACE)/316+RTFE 600# RF RED. BORE F.S GEAR (BA-482) (09)
15 - 100 A352-LCB(NACE)/316+RTFE 600# RF FULL BORE F.S (BA-481) (08-2,09)
150 - 600 A352-LCB(NACE)/316+RTFE 600# RF FULL BORE F.S GEAR (BA-483) (08-2,09)
BUTTERFLY
80 - 150 A352-LCB(NACE)/316+RTFE 600# LUG LEVER (BF-480) (09)
200 - 600 A352-LCB(NACE)/316+RTFE 600# LUG GEAR (BF-481) (09)
2 207/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
Note :
05
09
35 323.2.2 of ASME B31.3.
2 208/334
CLASS: 06D2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 209/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06E1
RATING ASME 600#
- LICENSOR B SGR,HN,LS 129-31 Hydrogen Service,PGM for thk > 12.70mm
PIPE (01)
15 - 20 A335-P11 SMLS BE SCH160
25 - 600 A335-P11 SMLS BE SCH80
650 - 650 A691-1.1/4Cr-Cl.22 EFW BE 30.18MM
700 - 700 A691-1.1/4Cr-Cl.22 EFW BE 31.75MM
750 - 750 A691-1.1/4Cr-Cl.22 EFW BE 33.34MM
800 - 800 A691-1.1/4Cr-Cl.22 EFW BE 34.93MM
850 - 850 A691-1.1/4Cr-Cl.22 EFW BE 38.10MM
900 - 900 A691-1.1/4Cr-Cl.22 EFW BE 39.69MM
950 - 950 A691-1.1/4Cr-Cl.22 EFW BE 41.28MM
1000 - 1000 A691-1.1/4Cr-Cl.22 EFW BE 44.45MM
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A182-F11-Cl.2 THRD 3000#
PLUGS (163)
15 - 40 A182-F11-Cl.2 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A182-F11-Cl.2 600# WN RF
ASME
650 - 1000 A182-F11-Cl.2 600# WN RF
B16.47-A
25 - 600 A182-F11-Cl.2 600# WN RF WITH J.B
WITH
SPREADER
650 - 1000 A182-F11-Cl.2 600# WN RF
ASME
B16.47-A
BLIND FLANGE
15 - 600 A182-F11-Cl.2 600# BLIND RF
ASME
650 - 1000 A182-F11-Cl.2 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A182-F11-Cl.2 600# FIG-8 FF
250 - 600 A182-F11-Cl.2 600# BLK&SPC FF
ASME
650 - 1000 A182-F11-Cl.2 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
ASME
650 - 1000 SW(304+GRAP)IO:304 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 210/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGR,HN,LS 129-31 Hydrogen Service,PGM for thk > 12.70mm
GATE
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BB OS&Y (GA-701) (08-2,09)
50 - 250 A217-WC6/13Cr+HF 600# RF BB OS&Y (GA-702) (08-2,09)
300 - 600 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR (GA-704) (08-2,09)
ASME
650 - 1000 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-706)
(GA-704)
WITH BY
300 - 600 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR PASS DN20 (08-2,09)
GLOBE
V/V(GL-701)
GLOBE
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BB OS&Y (GL-701) (09)
50 - 100 A217-WC6/13Cr+HF 600# RF BB OS&Y (GL-702) (09)
150 - 500 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR (GL-703) (09)
CHECK
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BC LIFT (CH-701) (61)
50 - 600 A217-WC6/13Cr+HF 600# RF BC SWING (CH-703) (62)
ASME
650 - 1000 A217-WC6/13Cr+HF 600# RF BC SWING B16.47-A (62)
(CH-705)
50 - 600 A217-WC6/13Cr 600# LUG DUAL PLATE (CH-702)
ASME
650 - 1000 A217-WC6/13Cr 600# LUG DUAL PLATE B16.47-A
(CH-704)
BALL
15 - 40 A217-WC6/316+HF 600# RF RED. BORE F.S (BA-701) (09)
150 - 600 A217-WC6/316+HF 600# RF RED. BORE F.S GEAR (BA-704) (09)
ASME
650 - 1000 A217-WC6/316+HF 600# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-706)
50 - 100 A217-WC6/316+HF 600# RF FULL BORE F.S (BA-703) (08-2,09)
150 - 600 A217-WC6/316+HF 600# RF FULL BORE F.S GEAR (BA-705) (08-2,09)
ASME
650 - 1000 A217-WC6/316+HF 600# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-707)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 211/334
CLASS: 06E1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W W B B B
250 W W W W R R R B B B
Header Size (DN)
300 W W W W R R R R B B B
350 W W W W R R R R R B B B
650 W W W W W W W W W W W W W W B B B
700 W W W W W W W W W W W W W W W B B B
750 W W W W W W W W W W W W W W W W B B B
800 W W W W W W W W W W W W W W W W W B B B
850 W W W W W W W W W W W W W W W W W W B B B
900 W W W W W W W W W W W W W W W W W W W B B B
950 W W W W W W W W W W W W W W W W W W W W B B B
1000 W W W W W W W W W W W W W W W W W W W W W B B B
Abbreviation
B Buttwelding Tee
2 212/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGR,LS 129-31 Hydrogen Service for thk > 12.70mm
PIPE (01)
15 - 20 A335-P11 SMLS BE XXS
25 - 50 A335-P11 SMLS BE SCH160
80 - 600 A335-P11 SMLS BE SCH80
650 - 650 A691-1.1/4Cr-Cl.22 EFW BE 31.75MM
700 - 700 A691-1.1/4Cr-Cl.22 EFW BE 33.34MM
750 - 750 A691-1.1/4Cr-Cl.22 EFW BE 34.93MM
800 - 800 A691-1.1/4Cr-Cl.22 EFW BE 38.10MM
850 - 850 A691-1.1/4Cr-Cl.22 EFW BE 39.69MM
900 - 900 A691-1.1/4Cr-Cl.22 EFW BE 41.28MM
950 - 950 A691-1.1/4Cr-Cl.22 EFW BE 42.45MM
1000 - 1000 A691-1.1/4Cr-Cl.22 EFW BE 46.04MM
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A182-F11-Cl.2 THRD 3000#
PLUGS (163)
15 - 40 A182-F11-Cl.2 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A182-F11-Cl.2 600# WN RF
ASME
650 - 1150 A182-F11-Cl.2 600# WN RF
B16.47-A
80 - 600 A182-F11-Cl.2 600# WN RF WITH J.B
WITH
SPREADER
650 - 1000 A182-F11-Cl.2 600# WN RF
ASME
B16.47-A
BLIND FLANGE
15 - 600 A182-F11-Cl.2 600# BLIND RF
ASME
650 - 1000 A182-F11-Cl.2 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A182-F11-Cl.2 600# FIG-8 FF
250 - 600 A182-F11-Cl.2 600# BLK&SPC FF
ASME
650 - 1000 A182-F11-Cl.2 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
ASME
650 - 1150 SW(304+GRAP)IO:304 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 213/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGR,LS 129-31 Hydrogen Service for thk > 12.70mm
GATE
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BB OS&Y (GA-701) (08-2,09)
50 - 250 A217-WC6/13Cr+HF 600# RF BB OS&Y (GA-702) (08-2,09)
300 - 600 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR (GA-704) (08-2,09)
ASME
650 - 1000 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-706)
GLOBE
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BB OS&Y (GL-701) (09)
50 - 100 A217-WC6/13Cr+HF 600# RF BB OS&Y (GL-702) (09)
150 - 300 A217-WC6/13Cr+HF 600# RF BB OS&Y GEAR (GL-703) (09)
CHECK
15 - 40 A182-F11-Cl.2/13Cr+HF 600# RF BC LIFT (CH-701) (61)
50 - 600 A217-WC6/13Cr+HF 600# RF BC SWING (CH-703) (62)
ASME
650 - 1000 A217-WC6/13Cr+HF 600# RF BC SWING B16.47-A (62)
(CH-705)
50 - 600 A217-WC6/13Cr 600# LUG DUAL PLATE (CH-702)
ASME
650 - 1000 A217-WC6/13Cr 600# LUG DUAL PLATE B16.47-A
(CH-704)
BALL
150 - 600 A217-WC6/316+HF 600# RF RED. BORE F.S GEAR (BA-704) (09)
ASME
650 - 1000 A217-WC6/316+HF 600# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-706)
50 - 100 A217-WC6/316+HF 600# RF FULL BORE F.S (BA-703) (08-2,09)
150 - 600 A217-WC6/316+HF 600# RF FULL BORE F.S GEAR (BA-705) (08-2,09)
ASME
650 - 1000 A217-WC6/316+HF 600# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-707)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 214/334
CLASS: 06E2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W W B B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 215/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06F1
RATING ASME 600#
- LICENSOR A AV,CLR,CLS,HPW,PW PWHT / NACE Reqd per B31.3 Sec 331
PIPE (01,19)
450 - 600 API5L-B-PSL.1 DSAW BE SCH80 (27)
NIPPLE (02,03,19)
SWAGE (02,03,19)
CAP (02)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (02)
15 - 40 A105 THRD HEX
FLANGEDOLET (02,05)
15 - 80 A105 600# RF To match pipe thickness
WELDOLET (02,05)
FLANGE (02)
15 - 600 A105 600# WN RF
100 - 600 A105 600# WN RF WITH J.B
15 - 50 A105 1500# WN RTJ (82)
80 - 600 A105 900# WN RTJ (82)
15 - 600 A105 600# WN RF
BLIND FLANGE
15 - 600 A105 600# BLIND RF
LINE BLANK
15 - 200 A105 600# FIG-8 FF
250 - 600 A105 600# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
REDUCING GASKET
15 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
2 216/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06F1
RATING ASME 600#
- LICENSOR A AV,CLR,CLS,HPW,PW PWHT / NACE Reqd per B31.3 Sec 331
GATE
15 - 40 A105/13Cr+HF 600# RF BB OS&Y (GA-128) (08,09)
50 - 250 A216-WCB/13Cr+HF 600# RF BB OS&Y (GA-133) (08,09)
300 - 600 A216-WCB/13Cr+HF 600# RF BB OS&Y GEAR (GA-129) (08,09)
15 - 40 A105/13Cr+HF 600# RF BB OS&Y (GA-128A) (08-2,09)
GLOBE
15 - 40 A105/13Cr+HF 600# RF BB OS&Y (GL-116) (08,09)
50 - 100 A216-WCB/13Cr+HF 600# RF BB OS&Y (GL-117) (08,09)
150 - 350 A216-WCB/13Cr+HF 600# RF BB OS&Y GEAR (GL-118) (08,09)
CHECK
15 - 40 A105/13Cr+HF 600# RF BC LIFT (CH-116) (08,09,61)
50 - 600 A216-WCB/13Cr+HF 600# RF BC SWING (CH-118) (08,09,62)
50 - 250 A216-WCB/13Cr+HF 600# WAFER DUAL PLATE (CH-117) (08,09)
REFERENCE
50 - 50 A216-WCB/13Cr+HF 600# RF BC BALL (08,09,61)
(CH-116)
BALL
15 - 100 A216-WCB/316+GRAP 600# RF FULL BORE F.S (BA-125) (08,09)
150 - 200 A216-WCB/316+GRAP 600# RF FULL BORE F.S GEAR (BA-104) (08,09)
15 - 100 A216-WCB/316+GRAP 600# RF FULL F.S EXT.BONNET (BA-125E)
BUTTERFLY
200 - 600 A216-WCB/316+GRAP 600# LUG GEAR (BF-108) (08,09)
3-WAY
20 - 100 A216-WCB/316+GRAP 600# RF RED. BORE F.S (08,09)
150 - 150 A216-WCB/316+GRAP 600# RF RED. BORE F.S GEAR (08,09)
Note :
05
08
09
27
35
323.2.2 of ASME B31.3.
2 217/334
CLASS: 06F1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 218/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06J1
RATING ASME 600#
- LICENSOR A WOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 20 A312-TP310 SMLS BE SCH160
25 - 200 A312-TP310 SMLS BE SCH80S
250 - 300 A312-TP310 SMLS BE SCH80
BEND (02,103)
15 - 300 A312-TP310 SMLS BE Tomatch pipe thickness 3D
NIPPLE (02,103)
15 - 40 A312-TP310 SMLS BBE Tomatch pipe thickness L=3"
15 - 300 A403-WP310 SMLS BW Tomatch pipe thickness
THREDOLET (163)
15 - 40 A182-F310 THRD 3000#
PLUGS (163)
15 - 40 A182-F310 THRD HEX
50 - 300 A182-F310 BW Tomatch pipe thickness
FLANGE (02,103)
15 - 300 A182-F310 600# WN RF
100 - 300 A182-F310 600# WN RF WITH J.B
15 - 65 A182-F310 1500# WN RJT (82)
80 - 250 A182-F310 900# WN RJT (82)
15 - 65 A182-F310 1500# WN RF
80 - 250 A182-F310 900# WN RF
BLIND FLANGE (103)
15 - 300 A182-F310 600# BLIND RF
GASKET
15 - 300 SW(310+GRAP)IO:310 600# RF 4.5MM (105)
15 - 65 SW(310+GRAP)IO:310 1500# RF 4.5MM (105)
80 - 300 SW(310+GRAP)IO:310 900# RF 4.5MM (105)
15 - 65 310SS 1500# RTJ OVAL RING (82)
80 - 250 310SS 900# RTJ OVAL RING (82)
BOLT/NUT
GATE
15 - 150 A494-M35-1/MONEL 600# BW BB OS&Y (GA-230) (08,08-3,09)
CHECK
15 - 40 A494-M35-1/MONEL 600# RF BC SWING (CH-260) (08,09,61)
50 - 250 A494-M35-1/MONEL 600# LUG DUAL PLATE (CH-261) (08,09,62)
BALL
15 - 100 A351-CF8M/MONEL+RTFE 600# RF FULL BORE F.S (BA-260) (08,08-3,09)
150 - 200 A351-CF8M/MONEL+RTFE 600# RF FULL BORE F.S GEAR (BA-261) (08,08-3,09)
15 - 100 A351-CF8M/MONEL+RTFE 600# RF FULL F.S EXT.BONNET (BA-260E)
15 - 100 A351-CF8M/MONEL 600# RF FULL BORE F.S (BA-260A)
150 - 200 A351-CF8M/MONEL 600# RF FULL BORE F.S GEAR (BA-261A)
2 219/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A WOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
Note :
08
09
2 220/334
CLASS: 06J1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 221/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06L0
RATING ASME 600#
TYPICAL SERVICE PCR DES. PRES.(barg) 99.3 to 50.0
- LICENSOR B PCR
PIPE (01)
15 - 40 A312-TP321 SMLS BE SCH80S
50 - 100 A312-TP321 SMLS BE SCH40S
150 - 600 A312-TP321 SMLS BE SCH80
NIPPLE (02,03)
15 - 40 A312-TP321 SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A403-WP321 SMLS BBE To match pipe thickness
15 - 600 A403-WP321 SMLS BW To match pipe thickness
THREDOLET (163)
15 - 40 A182-F321 THRD 3000#
PLUGS (163)
15 - 40 A182-F321 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A182-F321 600# WN RF
100 - 600 A182-F321 600# WN RF WITH J.B
100 - 600 A182-F321 900# WN RTJ
BLIND FLANGE
15 - 600 A182-F321 600# BLIND RF
LINE BLANK
15 - 200 A182-F321 600# FIG-8 FF
250 - 600 A182-F321 600# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
100 - 200 321SS 900# RTJ OVAL RING
BOLT/NUT
GATE
15 - 40 A182-F321/S&D HF 600# RF BB OS&Y (GA-501) (08-2,09)
50 - 250 A351-321SS/S&D HF 600# RF BB OS&Y (GA-502) (08-2,09)
300 - 600 A351-321SS/S&D HF 600# RF BB OS&Y GEAR (GA-504) (08-2,09)
GLOBE
15 - 40 A182-F321/S&D HF 600# RF BB OS&Y (GL-501) (09)
50 - 100 A351-321SS/S&D HF 600# RF BB OS&Y (GL-502) (09)
150 - 300 A351-321SS/S&D HF 600# RF BB OS&Y GEAR (GL-503) (09)
CHECK
15 - 40 A182-F321/S&D HF 600# RF BC LIFT (CH-501) (61)
50 - 600 A351-321SS/S&D HF 600# RF BC SWING (CH-502) (62)
BALL
15 - 100 A182-F321/S&D HF 600# RF RED. BORE F.S (BA-501) (09)
150 - 600 A351-321SS/S&D HF 600# RF RED. BORE F.S GEAR (BA-503) (09)
15 - 100 A182-F321/S&D HF 600# RF FULL BORE F.S (BA-502) (08-2,09)
150 - 600 A351-321SS/S&D HF 600# RF FULL BORE F.S GEAR (BA-504) (08-2,09)
2 222/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
TYPICAL SERVICE PCR DES. PRES.(barg) 99.3 to 50.0
- LICENSOR B PCR
Note :
05
09
35
323.2.2 of ASME B31.3.
2 223/334
CLASS: 06L0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 224/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGR,LS 129-31 Hydrogen Service
PIPE (01)
15 - 20 A312-TP321 SMLS BE SCH160
25 - 200 A312-TP321 SMLS BE SCH80S
250 - 600 A312-TP321 SMLS BE SCH80
650 - 650 A358-321-Cl.1 EFW BE 25.40MM
700 - 700 A358-321-Cl.1 EFW BE 27.00MM
750 - 750 A358-321-Cl.1 EFW BE 28.58MM
800 - 800 A358-321-Cl.1 EFW BE 31.75MM
850 - 850 A358-321-Cl.1 EFW BE 33.34MM
900 - 900 A358-321-Cl.1 EFW BE 34.93MM
950 - 950 A358-321-Cl.1 EFW BE 36.51MM
1000 - 1000 A358-321-Cl.1 EFW BE 38.10MM
NIPPLE (02,03)
SWAGE (02,03)
650 - 1000 A403-WP321 WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 40 A182-F321 THRD 3000#
PLUGS (163)
15 - 40 A182-F321 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A182-F321 600# WN RF
ASME
650 - 1000 A182-F321 600# WN RF
B16.47-A
100 - 600 A182-F321 600# WN RF WITH J.B
WITH
SPREADER
650 - 1000 A182-F321 600# WN RF
ASME
B16.47-A
BLIND FLANGE
15 - 600 A182-F321 600# BLIND RF
ASME
650 - 1000 A182-F321 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A182-F321 600# FIG-8 FF
250 - 600 A182-F321 600# BLK&SPC FF
ASME
650 - 1000 A182-F321 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
ASME
650 - 1000 SW(304+GRAP)IO:304 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 225/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGR,LS 129-31 Hydrogen Service
GATE
15 - 40 A182-F321/S&D HF 600# RF BB OS&Y (GA-501) (08-2,09)
50 - 250 A351-321SS/S&D HF 600# RF BB OS&Y (GA-502) (08-2,09)
300 - 600 A351-321SS/S&D HF 600# RF BB OS&Y GEAR (GA-504) (08-2,09)
ASME
650 - 1000 A351-321SS/S&D HF 600# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-506)
GLOBE
15 - 40 A182-F321/S&D HF 600# RF BB OS&Y (GL-501) (09)
50 - 100 A351-321SS/S&D HF 600# RF BB OS&Y (GL-502) (09)
150 - 300 A351-321SS/S&D HF 600# RF BB OS&Y GEAR (GL-503) (09)
CHECK
15 - 40 A182-F321/S&D HF 600# RF BC LIFT (CH-501) (61)
50 - 600 A351-321SS/S&D HF 600# RF BC SWING (CH-502) (62)
ASME
650 - 1000 A351-321SS/S&D HF 600# RF BC SWING B16.47-A (62)
(CH-503)
BALL
15 - 100 A182-F321/S&D HF 600# RF RED. BORE F.S (BA-501) (09)
150 - 600 A351-321SS/S&D HF 600# RF RED. BORE F.S GEAR (BA-503) (09)
ASME
650 - 1000 A351-321SS/S&D HF 600# RF RED. BORE F.S GEAR B16.47-A (09)
(BA-505)
15 - 100 A182-F321/S&D HF 600# RF FULL BORE F.S (BA-502) (08-2,09)
150 - 600 A351-321SS/S&D HF 600# RF FULL BORE F.S GEAR (BA-504) (08-2,09)
ASME
650 - 1000 A351-321SS/S&D HF 600# RF FULL BORE F.S GEAR B16.47-A (08-2,09)
(BA-506)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 226/334
CLASS: 06L1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W W B B B
Header Size (DN)
350 W W W W W W W W w B B B
Abbreviation
B Buttwelding Tee
2 227/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A GOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
BEND (02,103)
ANNEALED
15 - 100 B165-N04400 SMLS BE To match pipe thickness
3D
NIPPLE
ANNEALED
L=3"
SWAGE
15 - 100 B366-WPNC-S SMLS BBE To match pipe thickness ANNEALED
THREDOLET (163)
15 - 40 B564-N04400 THRD 3000# ANNEALED
PLUGS (163)
15 - 40 B564-N04400 THRD HEX ANNEALED
ELBOW/TEE/REDUCER/CAP (02,81,103)
15 - 100 B366-WPNC-S SMLS BW To match pipe thickness ANNEALED
50 - 100 B564-N04400 BW To match pipe thickness ANNEALED
FLANGE (02,103)
15 - 100 B564-N04400 600# WN RF ANNEALED
WITH J.B
100 - 100 B564-N04400 600# WN RF
ANNEALED
BLIND FLANGE (103)
15 - 20 B564-N04400 600# BLIND RF ANNEALED
25 - 100 A105(B127-N04400 3.2MM PLATED) 600# BLIND RF
GASKET
15 - 100 SW(ALLOY400+GRAPH)IO:ALLOY400 600# RF 4.5MM (104,105)
BOLT/NUT
GATE
15 - 40 ALLOY400/ALLOY400+HF 600# RF BB OS&Y (GA-302) (08-3,09,99,103)
50 - 100 ALLOY400/ALLOY400+HF 600# RF BB OS&Y (GA-308) (08-3,09,99,103)
GLOBE
15 - 100 ALLOY400/ALLOY400+HF 600# RF BB OS&Y (GL-303) (08-3,09,99,103)
CHECK
15 - 100 ALLOY400/ALLOY400+HF 600# RF BC SWING (CH-303) (62,99,103)
(07,26,63,99,
80 - 100 ALLOY400/ALLOY400+HF 600# WAFER DUAL PLATE (CH-304)
103)
BALL
15 - 100 ALLOY400/ALLOY400+RTFE 600# RF FULL BORE F.S (BA-303) (09,99,103)
2 228/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A GOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
Note :
09
58 For Oxygen pressure greater than 100 psig (6895kPag), oxygen supplier shall be consulted.
102
2 229/334
CLASS: 06NM
Branch Size (DN)

15 20 25 40 50 80 100
15 B
Header Size (DN)
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
Abbreviation
B Buttwelding Tee
2 230/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06P1
RATING ASME 600#
- LICENSOR A HWP,PW PWHT / NACE Reqd per B31.3 Sec 331
PIPE (01,109)
100 - 100 API5L-B-PSL.1 SMLS BE 7.14MM
125 - 125 API5L-B-PSL.1 SMLS BE 7.92MM
150 - 150 API5L-B-PSL.1 SMLS 600# RF 9.53MM (116)
BASALT LINING
200 - 200 API5L-B-PSL.1 DSAW 600# RF SCH80 OF 100 OR (116)
125 ID
BASALT LINING
250 - 250 API5L-B-PSL.1 DSAW 600# RF 14.27MM OF 150 ID
(116)
BASALT LINING
300 - 300 API5L-B-PSL.1 DSAW 600# RF SCH80 OF 200 ID
(116)
BASALT LINING
400 - 400 API5L-B-PSL.1 DSAW 600# RF SCH80 OF 300 ID
(116)
BEND (02)
150 - 150 API5L-B-PSL.1 SMLS 600# RF To match pipe thickness
6D
(BASALT LINING
200 - 200 API5L-B-PSL.1 DSAW 600# RF To match pipe thickness OF 100 OR
(116)
125 ID)
6D
250 - 250 API5L-B-PSL.1 DSAW 600# RF To match pipe thickness (BASALT LINING(116)
OF 150 ID)
6D
OF 200 ID)
6D
OF 300 ID)
5D (BASALT
300 - 300 API5L-B-PSL.1 DSAW 600# RF To match pipe thickness LINING OF 200 (116)
ID)
5D (BASALT
ID)
4D (BASALT
ID)
SWAGE (02,114)
ELBOW/TEE/LATERAL/REDUCER (02)
150 - 150 A234-WPB SMLS 600# RF To match pipe thickness (116)
BASALT LINING
200 - 200 A234-WPB WELD 600# RF To match pipe thickness OF 100 OR (116)
125 ID
250 - 250 A234-WPB WELD 600# RF To match pipe thickness BASALT LINING (116)
OF 150 ID
300 - 300 A234-WPB WELD 600# RF To match pipe thickness BASALT LINING (116)
OF 200 ID
WELD 600# RF To match pipe thickness (BASALT
OF 300 ID)LINING (116)
400 - 400 A234-WPB
FLAGNEOLET (02)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
2 231/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06P1
RATING ASME 600#
- LICENSOR A HWP,PW PWHT / NACE Reqd per B31.3 Sec 331
STUB-END (02)
LONG PATTERN
(BASALT LINING
200 - 200 A234-WPB WELD BW To match pipe thickness OF 100 OR
(116)
125 ID)
LONG PATTERN
250 - 250 A234-WPB WELD BW To match pipe thickness (BASALT LINING (116)
OF 150 ID)
LONG PATTERN
OF 200 ID)
LONG PATTERN
OF 300 ID)
FLANGE (02)
15 - 300 A105 600# LJ
100 - 300 A105 600# LJ WITH J.B
15 - 300 A105 600# WN RF (82)
15 - 300 A105 600# WN RF
BLIND FLANGE
15 - 300 A105 600# BLIND RF
GASKET
15 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
REDUCING GASKET
15 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
KNIFE GATE
250 - 300 A395/316+METAL 600# WAFER BONNETLESS (KG-103A) (08,09)
BALL
15 - 100 A351-CF8M/DUPLEX+HF 600# RF FULL BORE F.S (BA-222) (08,09)
150 - 300 A351-CF8M/DUPLEX+HF 600# RF FULL BORE F.S GEAR (BA-222) (08,09)
15 - 100 A351-CF8M/DUPLEX+HF 600# RF FULL F.S EXT.BONNET (BA-222E) (08,09)
Note :
08
09
35
323.2.2 of ASME B31.3.
116 Pipe thickness chosen for closest match to lining o/d, keeping within required calculated thickness.
2 232/334
CLASS: 06P1
Branch Size (DN)

15 20 25 40 50 80 100 125 150 200 250 300 400
15 B
20 B B
25 B B B
40 B B B B
Header Size (DN)
50 B B B B B
80 B B B B B B
100 B B B B B B B
125 B B B B B B B B
150 B B B B B B B B B
200 B B B B B B B B B B
250 N N N N N N B B B B B
300 N N N N N N B B B B B B
400 N N N N N N N N B B B B B
Abbreviation
B Buttwelding Tee
2 233/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06Q1
RATING ASME 600#
- LICENSOR A HPW,PW PWHT / NACE Not required
- LICENSOR B
PIPE (01,110)
15 - 20 A312-TP304/304L SMLS BE SCH160
25 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH80
350 - 350 A312-TP304/304L DSAW BE SCH80
BEND (02,114)
80 - 300 A312-TP304/304L SMLS BE SCH160 3D (110,111)
80 - 200 A312-TP304/304L SMLS BE SCH160 5D (110,111)
NIPPLE (02,114)
ELBOW/TEE/REDUCER/LATERAL/CAP (02,114)
CROSS (02,114)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
STUB-END (02,114)
15 - 300 A403-WP304/304L SMLS BW To match pipe thickness LONG
PATTERN
FLANGE (02)
15 - 300 A105(GALV) 600# LJ
100 - 300 A105(GALV) 600# LJ WITH J.B
15 - 300 A182-F304/304L 600# WN RF (82)
250 - 300 A182-F304/304L 600# WN RF
BLIND FLANGE
15 - 300 A182-F304/304L 600# BLIND RF
GASKET
15 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
REDUCING GASKET
15 - 350 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
GATE
15 - 25 A105/13Cr+HF 600# RF BB OS&Y (GA-128) (08-3,09,115)
BALL
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S (BA-223) (08-3,09)
150 - 250 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S GEAR (BA-221) (08-3,09)
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL F.S EXT.BONNET (BA-223E) (08-3,09)
2 234/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06Q1
RATING ASME 600#
- LICENSOR A HPW,PW PWHT / NACE Not required
- LICENSOR B
Note :
09
110
111
115 To be used for test drains and vents only and shall be removed after testing.
2 235/334
CLASS: 06Q1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 236/334
CLASS: 06Q1 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 237/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A HDW PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 40 A312-TP304/304L SMLS BE SCH80S
50 - 100 A312-TP304/304L SMLS BE SCH40S
150 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH60
350 - 600 A312-TP304/304L DSAW BE SCH80
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F304/304L 600# WN RF
100 - 600 A182-F304/304L 600# WN RF WITH J.B
150 - 200 A182-F304/304L 900# WN RTJ
BLIND FLANGE
15 - 300 A182-F304/304L 600# BLIND RF
LINE BLANK
150 - 200 A182-F304/304L 600# FIG-8 FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
GATE
15 - 40 A182-F316/316 600# RF BB OS&Y (GA-209) (09)
50 - 250 A351-CF8M/316 600# RF BB OS&Y (GA-233) (09)
GLOBE
15 - 40 A182-F316/316 600# RF BB OS&Y (GL-207) (09)
50 - 100 A351-CF8M/316 600# RF BB OS&Y (GL-214) (09)
CHECK
15 - 40 A182-F316/316 600# RF BC LIFT (CH-207) (61)
BALL
2 238/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A HDW PWHT / NACE Not required
- LICENSOR B
Note :
09
2 239/334
CLASS: 06SA0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 240/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A SPW,HDW PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 40 A312-TP304/304L SMLS BE SCH80S
50 - 100 A312-TP304/304L SMLS BE SCH40S
150 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH60
350 - 600 A312-TP304/304L DSAW BE SCH80
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F304/304L 600# WN RF
100 - 600 A182-F304/304L 600# WN RF WITH J.B
15 - 50 A182-F304/304L 1500# WN RTJ (82)
80 - 100 A182-F304/304L 900# WN RTJ (82)
80 - 200 A182-F304/304L 1500# WN RTJ (82)
BLIND FLANGE
15 - 600 A182-F304/304L 600# BLIND RF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
GATE
15 - 40 A182-F316/316 600# RF BB OS&Y (GA-209) (09)
50 - 250 A351-CF8M/316 600# RF BB OS&Y (GA-233) (09)
GLOBE
15 - 40 A182-F316/316 600# RF BB OS&Y (GL-207) (09)
50 - 100 A351-CF8M/316 600# RF BB OS&Y (GL-214) (09)
CHECK
15 - 40 A182-F316/316 600# RF BC LIFT (CH-207) (61)
BALL
2 241/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR A SPW,HDW PWHT / NACE Not required
- LICENSOR B
Note :
09
2 242/334
CLASS: 06SS
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 243/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B HPCM,SGR,RECT,RW(HOLD),HPW(HOLD)
PIPE (01)
15 - 40 A312-TP304/304L SMLS BE SCH80S
50 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH60
350 - 350 A358-304/304L-Cl.1 EFW BE 14.27MM
400 - 400 A358-304/304L-Cl.1 EFW BE 15.88MM
450 - 450 A358-304/304L-Cl.1 EFW BE 17.48MM
500 - 500 A358-304/304L-Cl.1 EFW BE 19.05MM
600 - 600 A358-304/304L-Cl.1 EFW BE 22.23MM
650 - 650 A358-304/304L-Cl.1 EFW BE 23.83MM
700 - 750 A358-304/304L-Cl.1 EFW BE 27.00MM
800 - 800 A358-304/304L-Cl.1 EFW BE 30.18MM
900 - 900 A358-304/304L-Cl.1 EFW BE 32.51MM
1000 - 1000 A358-304/304L-Cl.1 EFW BE 36.02MM
1100 - 1100 A358-304/304L-Cl.1 EFW BE 40.00MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F304/304L 600# WN RF
ASME
650 - 1100 A182-F304/304L 600# WN RF
B16.47-A
100 - 600 A182-F304/304L 600# WN RF WITH J.B
WITH
SPREADER
650 - 1100 A182-F304/304L 600# WN RF
ASME
B16.47-A
ASME
700 - 750 A182-F304/304L 900# WN RTJ
B16.47-A
80 - 100 A182-F304/304L 1500# WN RTJ
BLIND FLANGE
15 - 600 A182-F304/304L 600# BLIND RF
ASME
650 - 1100 A182-F304/304L 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A240-304/304L 600# FIG-8 FF
250 - 600 A240-304/304L 600# BLK&SPC FF
ASME
650 - 1100 A240-304/304L 600# BLK&SPC FF
B16.47-A
2 244/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
GASKET
ASME
B16.47-A
150 - 600 SS304/304L 900# RTJ OVAL RING
ASME
700 - 700 SS304/304L 900# RTJ OVAL RING
B16.47-A
ASME
80 - 80 SS304/304L 1500# RTJ OVAL RING
B16.47-A
BOLT/NUT
VALVES FOR FLUID : HPCM, SGR, RECT (Operating between -46℃ and 300℃)
GATE
15 - 40 A182-F316/316 600# RF BB OS&Y (GA-209) (08-2,09)
50 - 250 A351-CF8M/316 600# RF BB OS&Y (GA-233) (08-2,09)
ASME
(GA-234)
GLOBE
15 - 40 A182-F316/316 600# RF BB OS&Y (GL-207) (09)
50 - 100 A351-CF8M/316 600# RF BB OS&Y (GL-214) (09)
CHECK
15 - 40 A182-F316/316 600# RF BC LIFT (CH-362) (61)
ASME
(CH-365)
ASME
(CH-366)
BALL
ASME
(BA-233)
ASME
(BA-234)
BUTTERFLY
400 - 400 A351-CF8M/316+RTFE 600# LUG GEAR (BF-218A)
(BF-218B)
MECHANIC
400 - 450 A351-CF8M/316+RTFE 600# LUG GEAR AL STOP
MINIMUM
10%
2 245/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
Note :
09
2 246/334
CLASS: 06U0B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
Header Size (DN)
150 W W W W W B B B
200 W W W W W R B B B
250 W W W W W R R B B B
300 W W W W W R R R B B B
350 W W W W W R R R R B B B
400 W W W W W R R R R R B B B
450 W W W W W R R R R R R B B B
500 W W W W W R R R R R R R B B B
Abbreviation
B Buttwelding Tee
2 247/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B SGS,RECR,RECS,RECL,PGM(HOLD)
PIPE (01)
15 - 40 A312-TP304/304L SMLS BE SCH80S
50 - 150 A312-TP304/304L SMLS BE SCH40S
200 - 300 A312-TP304/304L SMLS BE SCH60
350 - 350 A358-304/304L-Cl.1 EFW BE 14.27MM
400 - 400 A358-304/304L-Cl.1 EFW BE 15.88MM
450 - 450 A358-304/304L-Cl.1 EFW BE 17.48MM
500 - 500 A358-304/304L-Cl.1 EFW BE 19.05MM
600 - 600 A358-304/304L-Cl.1 EFW BE 22.23MM
650 - 650 A358-304/304L-Cl.1 EFW BE 23.83MM
700 - 700 A358-304/304L-Cl.1 EFW BE 27.00MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 600 A182-F304/304L 600# WN RF
ASME
650 - 700 A182-F304/304L 600# WN RF
B16.47-A
100 - 600 A182-F304/304L 600# WN RF WITH J.B
WITH
SPREADER
650 - 700 A182-F304/304L 600# WN RF
ASME
B16.47-A
50 - 300 A182-F304/304L 900# WN RTJ (82)
BLIND FLANGE
15 - 600 A182-F304/304L 600# BLIND RF
ASME
650 - 700 A182-F304/304L 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A240-304/304L 600# FIG-8 FF
250 - 600 A240-304/304L 600# BLK&SPC FF
ASME
650 - 700 A240-304/304L 600# BLK&SPC FF
B16.47-A
GASKET
ASME
B16.47-A
BOLT/NUT
2 248/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
VALVES FOR FLUID : SGS (Operating below -46℃) IN HIGHLY EXPLOSIVE SERVICE
GATE
EXTENDED
15 - 40 A182-F316/316 600# RF BB OS&Y B.S BONNET (08-2,09)
(GA-285)
EXTENDED
(GA-285)
EXTENDED
BB OS&Y SPRING
100 - 250 A351-CF8M/316 600# RF BONNET (08-2,09)
LOADED
(GA-285)
EXTENDED
(GA-287)
EXTENDED
BONNET
650 - 700 A351-CF8M/316 600# RF BB OS&Y SP.L GEAR ASME (08-2,09)
B16.47-A
(GA-286)
GLOBE
EXTENDED
(GL-281)
EXTENDED
(GL-281)
EXTENDED
BB OS&Y SPRING
100 - 100 A351-CF8M/316 600# RF BONNET (09)
LOADED
(GL-281)
EXTENDED
(GL-282)
VALVES FOR FLUID : RECR, RECS, RECL (Operating below -46℃) IN CORROSIVE SERVICE
GATE
EXTENDED
15 - 40 A182-F316/316 600# RF BB OS&Y BONNET (08-2,09)
(GA-260)
EXTENDED
50 - 250 A351-CF8M/316 600# RF BB OS&Y BONNET (08-2,09)
(GA-260)
EXTENDED
300 - 600 A351-CF8M/316 600# RF BB OS&Y GEAR BONNET (08-2,09)
(GA-261)
EXTENDED
BONNET
650 - 700 A351-CF8M/316 600# RF BB OS&Y GEAR ASME (08-2,09)
B16.47-A
(GA-262)
GLOBE
EXTENDED
(GL-256)
EXTENDED
(GL-256)
EXTENDED
(GL-257)
2 249/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
CHECK
15 - 40 A182-F316/316 600# RF BC LIFT (CH-362) (61)
ASME
(CH-365)
ASME
650 - 700 A351-CF8M/316 600# WAFER DUAL PLATE B16.47-A (07,26-2,63)
(CH-366)
BALL
EXTENDED
(BA-362)
EXTENDED
(BA-364)
EXTENDED
BONNET
650 - 700 A351-CF8M/316+RTFE 600# RF RED. BORE F.S GEAR ASME (09)
B16.47-A
(BA-373)
EXTENDED
(BA-363)
EXTENDED
(BA-365)
EXTENDED
BONNET
650 - 700 A351-CF8M/316+RTFE 600# RF FULL BORE F.S GEAR ASME (08-2,09)
B16.47-A
(BA-374)
3-WAY
EXTENDED
150 - 600 A351-CF8M/316+RTFE 600# RF RED. BORE F.S GEARBONNET
REFERENCE 09)
(
(BA-364)
Note :
09
2 250/334
CLASS: 06U0C
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
Header Size (DN)
150 W W W W W B B B
200 W W W W W R B B B
250 W W W W W R R B B B
300 W W W W W R R R B B B
350 W W W W W R R R R B B B
400 W W W W W R R R R R B B B
450 W W W W W R R R R R R B B B
500 W W W W W R R R R R R R B B B
Abbreviation
B Buttwelding Tee
2 251/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06V2
RATING ASME 600#
- LICENSOR A FLR,SG PWHT / NACE Not required
- LICENSOR B
PIPE (01,110)
15 - 20 A312-TP304/304L SMLS BE XXS
25 - 50 A312-TP304/304L SMLS BE SCH160
65 - 200 A312-TP304/304L SMLS BE SCH80S
250 - 300 A312-TP304/304L SMLS BE SCH80
350 - 350 A312-TP304/304L DSAW BE 20.62MM
400 - 400 A312-TP304/304L DSAW BE 23.83MM
450 - 450 A312-TP304/304L DSAW BE 25.40MM
500 - 500 A312-TP304/304L DSAW BE 28.58MM
600 - 600 A312-TP304/304L DSAW BE 33.32MM
650 - 650 A240-304/304L DSAW BE 34.93MM
700 - 700 A240-304/304L DSAW BE 38.10MM
750 - 750 A240-304/304L DSAW BE 41.28MM
NIPPLE (02,114)
SWAGE (02,114)
ELBOW (02,114)
HIGH ALUMINA
600 - 600 A403-WP304/304L WELD 600# RF To match pipe thickness (90% ALUMINA OXIDE)
CERAMIC-LINING OF 500 ID
TEE/CAP/REDUCER
LATERAL
STUB-END (02,114)
15 - 300 A403-WP304/304L SMLS BW To match pipe thickness LONG
PATTERN
LONG
PATTERN
ELBOLET
150 - 150 A403-WP304/304L WELD BW SCH80S
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
2 252/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B
FLANGE (02)
15 - 600 A105 (GALV) 600# LJ
ASME
750 - 750 A182-F304/304L 600# WN RF
B16.47-A
HIGH
ALUMINA(9
0%
ALUMINA
600 - 600 A182-F304/304L 600# WN RF
OXIDE)
CERAMIC-
LINING OF
500 ID
100 - 600 A105 (GALV) 600# LJ WITH J.B
WITH
SPREADER
750 - 750 A182-F304/304L 600# WN RF
ASME
B16.47-A
15 - 600 A182-F304/304L 600# WN RF (82)
15 - 200 A182-F304/304L 1500# WN RTJ (82)
80 - 200 A182-F304/304L 900# WN RTJ (82)
65 - 65 A182-F304/304L 1500# WN RF
80 - 200 A182-F304/304L 900# WN RF
15 - 50 A182-F304/304L 600# WN RF
600 - 600 A182-F304/304L 600# WN RF 500 ID
BLIND FLANGE
15 - 600 A182-F304/304L 600# BLIND RF
LINE BLANK
15 - 200 A240-304/304L 600# FIG-8 FF
250 - 600 A240-304/304L 600# BLK&SPC FF
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
15 - 65 SW(304+GRAP)IO:304 1500# RF 4.5MM
80 - 600 SW(304+GRAP)IO:304 900# RF 4.5MM
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
REDUCING GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
A193-B8-Cl.2/A194-8 STUD/H.HEX (10)
2 253/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B
GATE
15 - 40 A182-F316/316 600# RF BB OS&Y (GA-215) (08,09)
50 - 250 A351-CF8M/316 600# RF BB OS&Y (GA-215A) (08,09)
300 - 600 A351-CF8M/316 600# RF BB OS&Y GEAR (GA-216) (08,09)
ASME
650 - 650 A351-CF8M/316 600# RF BB OS&Y GEAR B16.47-A (08,09)
(GA-217)
GLOBE
15 - 40 A182-F316/316 600# RF BB OS&Y (GL-213A) (08,09)
50 - 100 A351-CF8M/316 600# RF BB OS&Y (GL-213) (08,09)
150 - 300 A351-CF8M/316 600# RF BB OS&Y GEAR (GL-313) (08,09)
NEEDLE
REFERENCE
25 - 25 A182-F316/316 600# RF BB OS&Y (08,09)
(GL-213)
CHECK
REFERENCE
15 - 40 A182-F316/316 600# RF BC LIFT (08,09)
(CH-207)
50 - 300 A351-CF8M/316 600# LUG DUAL PLATE (CH-215) (08,09)
BALL
15 - 100 A351-CF8M/WC-INCONEL+HF 600# RF FULL BORE F.S (BA-270) (08,09,17)
150 - 200 A351-CF8M/WC-INCONEL+HF 600# RF FULL BORE F.S GEAR (BA-271) (08,09,17)
15 - 100 A351-CF8M/WC-INCONEL+HF 600# RF FULL F.S EXT.BONNET (BA-270E)
15 - 100 A351-CF8M/CrC-SS+HF 600# RF FULL BORE F.S (BA-272) (08,09,17-2)
150 - 600 A351-CF8M/CrC-SS+HF 600# RF FULL BORE F.S GEAR (BA-273) (08,09,17-2)
ASME
650 - 750 A351-CF8M/CrC-SS+HF 600# RF FULL BORE F.S GEAR B16.47-A (08,09,17-2)
(BA-274)
BUTTERFLY
200 - 600 A351-CF8M/316 600# DOUBLE FLG GEAR (BF-220) (08,09,16)
Note :
08
09
16 Not to be used where the service consists of char-laden syngas.
17 This valve should only be used for in-line process valves where Char is present.
17-2 This valve should only be used when Char is not present, or the valve is not in-line.
110
2 254/334
CLASS: 06V2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 750
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 255/334
CLASS: 06V2 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 256/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06W2
RATING ASME 600#
- LICENSOR A SLU PWHT / NACE Reqd per B31.3 Sec 331
PIPE (01,19)
15 - 20 API5L-B-PSL.1 SMLS BE XXS
NIPPLE (02,114)
BEND
15 - 80 API5L-B-PSL.1 SMLS BE To match pipe thickness 3D
15 - 80 API5L-B-PSL.1 SMLS BE To match pipe thickness 5D
ELBOW/TEE/LATERAL/REDUCER (02,114)
SWAGE
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
FLANGE (02,114)
15 - 300 A105 600# WN RF
100 - 300 A105 600# WN RF WITH J.B
80 - 80 A105 900# WN RTJ (82)
BLIND FLANGE (114)
15 - 300 A105 600# BLIND RF
GASKET
15 - 300 SW(304+GRAP)IO:304 600# RF 4.5MM
BOLT/NUT
CHECK
25 - 40 A105/13Cr+HF 600# RF BC LIFT (CH-116) (08,09)
50 - 250 A216-WCB/13Cr+HF 600# WAFER DUAL PLATE (CH-117) (08,09)
BALL
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S (BA-220) (08,09)
150 - 250 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL BORE F.S GEAR (BA-221) (08,09)
25 - 100 A351-CF8M/Cr Pl.SS+METAL 600# RF FULL F.S EXT.BONNET (BA-220E) (08,09)
2 257/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06W2
RATING ASME 600#
- LICENSOR A SLU PWHT / NACE Reqd per B31.3 Sec 331
Note :
08
09
35
323.2.2 of ASME B31.3.
2 258/334
CLASS: 06W2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 259/334
CLASS: 06W2 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 260/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B RECL,SGT,SGR,HCD,SGS,PGM,SNG
PIPE (01,27)
15 - 20 A106-B SMLS BE SCH160
25 - 200 A106-B SMLS BE SCH80
250 - 600 A333-6 SMLS BE SCH80
650 - 650 A671-CC65-Cl.22 DSAW BE 26.97MM
700 - 700 A671-CC65-Cl.22 DSAW BE 28.58MM
750 - 750 A671-CC65-Cl.22 DSAW BE 30.18MM
800 - 800 A671-CC65-Cl.22 DSAW BE 31.75MM
850 - 850 A671-CC65-Cl.22 DSAW BE 33.34MM
900 - 900 A671-CC65-Cl.22 DSAW BE 34.93MM
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A105 600# WN RF
25 - 600 A105 600# WN RF
ASME
650 - 900 A105 600# WN RF
B16.47-A
100 - 600 A105 600# WN RF WITH J.B
WITH
SPREADER
650 - 900 A105 600# WN RF
ASME
B16.47-A
25 - 50 A105 1500# WN RTJ (82)
80 - 600 A105 900# WN RTJ (82)
BLIND FLANGE
15 - 600 A105 600# BLIND RF
ASME
650 - 900 A105 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A105 600# FIG-8 FF
250 - 600 A105 600# BLK&SPC FF
ASME
650 - 900 A105 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
ASME
650 - 900 SW(304+GRAP)IO:304 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 261/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
VALVES FOR STANDARD FLUIDS
GATE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GA-180) (08-2,09)
50 - 250 A216-WCB/S&D HF 600# BW BB OS&Y (GA-114) (08-2,09)
300 - 600 A216-WCB/S&D HF 600# BW BB OS&Y GEAR (GA-115) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# BW BB OS&Y GEAR B16.47-A (08-2,09)
(GA-188)
(GA-114)
WITH BY
250 - 250 A216-WCB/S&D HF 600# BW BB OS&Y PASS DN20 (08-2,09)
GLOBE
V/V(GL-106)
50 - 250 A216-WCB/S&D HF 600# RF BB OS&Y (GA-112) (08-2,09)
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y GEAR (GA-113) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-187)
GLOBE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GL-180) (09)
CHECK
15 - 40 A105/S&D HF 600# BW BC LIFT (CH-126) (61)
BALL
ASME
(BA-186)
ASME
(BA-187)
BUTTERFLY
15 - 100 A216-WCB/316+RTFE 600# LUG LEVER (BF-120)
150 - 600 A216-WCB/316+RTFE 600# LUG GEAR (BF-120A)
ASME
650 - 900 A216-WCB/316+RTFE 600# LUG GEAR B16.47-
A(BF-186A)
(BF-120B)
MECHANIC
200 - 450 A216-WCB/316+RTFE 600# LUG GEAR AL STOP
MINIMUM
10%
ASME
B16.47-
A(BF-186B)
700 - 700 A216-WCB/316+RTFE 600# LUG GEAR MECHANIC
AL STOP
MINIMUM
10%
2 262/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
VALVES FOR HIGHLY EXPLOSIVE FLUIDS
GATE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GA-180) (08-2,09)
BB OS&Y SPRING
100 - 250 A216-WCB/S&D HF 600# BW (GA-182) (08-2,09)
LOADED
300 - 600 A216-WCB/S&D HF 600# BW BB OS&Y SP.L GEAR (GA-184) (08-2,09)
BB OS&Y SPRING
100 - 250 A216-WCB/S&D HF 600# RF (GA-181) (08-2,09)
LOADED
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR (GA-183) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR B16.47-A (08-2,09)
(GA-185)
GLOBE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GL-180)
100 - 100 A216-WCB/S&D HF 600# RF BB OS&Y SPRING (GL-181) (09)
LOADED
150 - 300 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR (GL-182) (09)
CHECK
BALL
ASME
(BA-184)
ASME
(BA-185)
Note :
05
09
27
35
323.2.2 of ASME B31.3.
2 263/334
CLASS: 06X1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W W B B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 264/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B PGM
PIPE (01,27)
25 - 50 A106-B SMLS BE SCH160
80 - 150 A106-B SMLS BE SCH80
200 - 200 A106-B SMLS BE SCH100
250 - 300 A333-6 SMLS BE SCH100
350 - 600 A333-6 SMLS BE SCH80
650 - 650 A671-CC65-Cl.22 DSAW BE 28.58MM
700 - 700 A671-CC65-Cl.22 DSAW BE 30.18MM
750 - 750 A671-CC65-Cl.22 DSAW BE 31.75MM
800 - 800 A671-CC65-Cl.22 DSAW BE 33.34MM
850 - 850 A671-CC65-Cl.22 DSAW BE 34.93MM
900 - 900 A671-CC65-Cl.22 DSAW BE 38.10MM
NIPPLE (02,03)
SWAGE (02,03)
ELBOW/TEE/CAP/REDUCER (02)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A105 600# WN RF
ASME
650 - 900 A105 600# WN RF
B16.47-A
100 - 600 A105 600# WN RF WITH J.B
WITH
SPREADER
650 - 900 A105 600# WN RF
ASME
B16.47-A
80 - 300 A105 900# WN RTJ
BLIND FLANGE
15 - 600 A105 600# BLIND RF
ASME
650 - 900 A105 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A105 600# FIG-8 FF
250 - 600 A105 600# BLK&SPC FF
ASME
650 - 900 A105 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(304+GRAP)IO:304 600# RF 4.5MM
ASME
650 - 900 SW(304+GRAP)IO:304 600# RF 4.5MM
B16.47-A
80 - 600 SOFT IRON 900# RTJ OVAL RING
BOLT/NUT
2 265/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B PGM
GATE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GA-180) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# BW BB OS&Y GEAR B16.47-A (08-2,09)
(GA-188)
(GA-114)
WITH BY
GLOBE
V/V(GL-106)
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y GEAR (GA-113) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# RF BB OS&Y GEAR B16.47-A (08-2,09)
(GA-187)
GLOBE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GL-180) (09)
CHECK
BALL
ASME
(BA-186)
ASME
(BA-187)
2 266/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B PGM
VALVES FOR FLUID : SGS (HIGHLY EXPLOSIVE SERVICE)
GATE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GA-180) (08-2,09)
BB OS&Y SPRING
100 - 250 A216-WCB/S&D HF 600# BW (GA-182) (08-2,09)
LOADED
BB OS&Y SPRING
100 - 250 A216-WCB/S&D HF 600# RF (GA-181) (08-2,09)
LOADED
300 - 600 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR (GA-183) (08-2,09)
ASME
650 - 900 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR B16.47-A (08-2,09)
(GA-185)
GLOBE
15 - 40 A105/S&D HF 600# BW BB OS&Y (GL-180) (09)
100 - 100 A216-WCB/S&D HF 600# RF BB OS&Y SPRING (GL-181) (09)
LOADED
150 - 300 A216-WCB/S&D HF 600# RF BB OS&Y SP.L GEAR (GL-182) (09)
CHECK
BALL
ASME
(BA-184)
ASME
(BA-185)
Note :
05
09
27
35
323.2.2 of ASME B31.3.
2 267/334
CLASS: 06X2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W W B B B
Header Size (DN)
Abbreviation
B Buttwelding Tee
2 268/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B PCR,SGR
PIPE (01,100)
15 - 40 A790-S31803 SMLS BE SCH80S
50 - 300 A790-S31803 SMLS BE SCH40S
350 - 600 A790-S31803 SMLS BE SCH40
650 - 650 A790-S31803 EFW BE 19.05MM RT 100%
700 - 700 A790-S31803 EFW BE 20.62MM RT 100%
750 - 750 A790-S31803 EFW BE 22.23MM RT 100%
800 - 800 A790-S31803 EFW BE 23.83MM RT 100%
850 - 850 A790-S31803 EFW BE 25.40MM RT 100%
900 - 900 A790-S31803 EFW BE 26.97MM RT 100%
950 - 1000 A790-S31803 EFW BE 28.58MM RT 100%
1050 - 1050 A790-S31803 EFW BE 30.18MM RT 100%
1100 - 1100 A790-S31803 EFW BE 31.75MM RT 100%
SWAGE (02,114)
NIPPLE (02)
650 - 1100 A815-S31803 WELD BW To match pipe thickness RT 100%
THREDOLET (163)
15 - 40 A182-F51 THRD 3000#
PLUGS (163)
15 - 40 A182-F51 THRD HEX
WELDOLET (02,81)
50 - 1100 A182-F51 BW
FLANGE (02)
15 - 600 A182-F51 600# WN RF
ASME
650 - 1100 A182-F51 600# WN RF
B16.47-A
100 - 600 A182-F51 600# WN RF WITH J.B
WITH
SPREADER
650 - 1100 A182-F51 600# WN RF
ASME
B16.47-A
BLIND FLANGE
15 - 600 A182-F51 600# BLIND RF
ASME
650 - 1100 A182-F51 600# BLIND RF
B16.47-A
LINE BLANK
15 - 200 A182-F51 600# FIG-8 FF
250 - 600 A182-F51 600# BLK&SPC FF
ASME
650 - 1100 A182-F51 600# BLK&SPC FF
B16.47-A
GASKET
15 - 600 SW(316+GRAP)IO:316 600# RF 4.5MM
ASME
650 - 1100 SW(316+GRAP)IO:316 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 269/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 600#
- LICENSOR B PCR,SGR
GATE
15 - 40 A351-CD4MCu/DUPLEX 2205+HF 600# RF BB OS&Y (GA-620) (09)
300 - 600 A351-CD4MCu/DUPLEX 2205+HF 600# RF BB OS&Y GEAR (GA-622) (09)
650 - 1100 A351-CD4MCu/DUPLEX 2205+HF 600# RF BB OS&Y GEAR (GA-623) (09)
BB OS&Y SPRING
100 - 250 A351-CD4MCu/DUPLEX 2205+HF 600# RF (GA-625) (09)
LOADED
300 - 600 A351-CD4MCu/DUPLEX 2205+HF 600# RF BB OS&Y SP.L GEAR (GA-626) (09)
650 - 1100 A351-CD4MCu/DUPLEX 2205+HF 600# RF BB OS&Y SP.L GEAR (GA-627) (09)
GLOBE
BB OS&Y SPRING
100 - 100 A351-CD4MCu/DUPLEX 2205 600# RF (GL-622) (09)
LOADED
150 - 300 A351-CD4MCu/DUPLEX 2205 600# RF BB OS&Y SP.L GEAR (GL-623) (09)
CHECK
15 - 40 A182-F53/DUPLEX 2205 600# BW BC LIFT (CH-620) (61)
ASME
650 - 1100 A351-CD4MCu/DUPLEX 2205 600# RF BC SWING B16.47-A (07,26,63)
(CH-623)
ASME
650 - 1100 A351-CD4MCu/DUPLEX 2205 600# WAFER DUAL PLATE B16.47-A (07,26,63)
(CH-624)
Note :
09
81 Integrally reinforced branch connections, tees, and reducing tees are permitted as an acceptable alternative branch connection. Not
100 to be used over 315℃.
2 270/334
CLASS: 06Y0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 100010501100
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W R B B B
200 W W W W R R B B B
Header Size (DN)
400 W W W W R R R R R R B B B
450 W W W W R R R R R R R B B B
500 W W W W R R R R R R R R B B B
600 W W W W R R R R R R R R R B B B
650 W W W W R R R R R R R R R R B B B
1050 W W W W W W W W W W W W W W W W W W W W W W B B B
1100 W W W W W W W W W W W W W W W W W W W W W W W B B B
Abbreviation
B Buttwelding Tee
2 271/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06Z0
RATING ASME 600#
TYPICAL SERVICE NOT USED DES. PRES.(barg) 102.6 to 56.5
- LICENSOR B
PIPE (01)
15 - 40 B677-N08904 SMLS BE SCH80S
50 - 150 B677-N08904 SMLS BE SCH40S
200 - 450 B677-N08904 SMLS BE SCH60
500 - 500 B677-N08904 SMLS BE 22.23MM
600 - 600 B677-N08904 SMLS BE 25.40MM
650 - 650 B625-N08904 EFW BE 23.83MM
700 - 700 B625-N08904 EFW BE 27.00MM
750 - 750 B625-N08904 EFW BE 28.58MM
800 - 800 B625-N08904 EFW BE 30.18MM
850 - 850 B625-N08904 EFW BE 31.75MM
900 - 900 B625-N08904 EFW BE 33.34MM
950 - 950 B625-N08904 EFW BE 34.93MM
1000 - 1000 B625-N08904 EFW BE 38.10MM
NIPPLE (02)
15 - 40 B625-N08904 SMLS BBE To match pipe thickness L=3"
SWAGE (02)
15 - 600 B366-N08904 SMLS BW To match pipe thickness
650 - 1000 B366-N08904 WELD BW To match pipe thickness
CAP (02)
15 - 600 B366-N08904 SMLS BW To match pipe thickness
THREDOLET (163)
15 - 40 B564-N08904 THRD 3000#
PLUGS (163)
15 - 40 B564-N08904 THRD HEX
WELDOLET (02)
50 - 1000 B564-N08904 BW To match pipe thickness
FLANGE (02)
15 - 600 B564-N08904 600# WN RF
ASME
650 - 1000 B564-N08904 600# WN RF
B16.47-A
100 - 600 B564-N08904 600# WN RF WITH J.B
WITH
SPREADER
650 - 1000 B564-N08904 600# WN RF
ASME
B16.47-A
BLIND FLANGE
15 - 600 B564-N08904 600# BLIND RF
ASME
650 - 900 B564-N08904 600# BLIND RF
B16.47-A
LINE BLANK
25 - 25 B564-N08904 600# FIG-8 FF
GASKET
15 - 600 SW(904L+GRAP)IO:904L 600# RF 4.5MM
ASME
650 - 1000 SW(904L+GRAP)IO:904L 600# RF 4.5MM
B16.47-A
BOLT/NUT
2 272/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 06Z0
RATING ASME 600#
TYPICAL SERVICE NOT USED DES. PRES.(barg) 102.6 to 56.5
- LICENSOR B
GATE
15 - 250 B564-N08904/904L 600# RF BB OS&Y (GA-800) (09)
300 - 600 B564-N08904/904L 600# RF BB OS&Y GEAR (GA-801) (09)
ASME
650 - 900 B564-N08904/904L 600# RF BB OS&Y GEAR B16.47-A (09)
(GA-802)
GLOBE
15 - 100 B564-N08904/904L 600# RF BB OS&Y (GL-800) (09)
150 - 300 B564-N08904/904L 600# RF BB OS&Y GEAR (GL-801) (09)
CHECK
15 - 600 B564-N08904/904L 600# RF BC SWING (CH-800) (62)
ASME
650 - 900 B564-N08904/904L 600# RF BC SWING B16.47-A (62)
(CH-802)
80 - 600 B564-N08904/904L 600# WAFER DUAL PLATE (CH-801) (07,26,63)
ASME
650 - 900 B564-N08904/904L 600# WAFER DUAL PLATE B16.47-A (07,26,63)
(CH-803)
BALL
15 - 80 B564-N08904/904L+HF 600# RF FULL BORE F.S (BA-800) (09)
100 - 600 B564-N08904/904L+HF 600# RF FULL BORE F.S GEAR (BA-801) (09)
650 - 900 B564-N08904/904L+HF 600# RF FULL BORE F.S GEAR (BA-802) (09)
Note :
09
2 273/334
CLASS: 06Z0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600 650 700 750 800 850 900 950 1000
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W W B B
100 W W W W B B B
150 W W W W R B B B
200 W W W W R R B B B
Header Size (DN)
400 W W W W R R R R R R B B B
450 W W W W R R R R R R R B B B
500 W W W W R R R R R R R R B B B
600 W W W W R R R R R R R R R B B B
650 W W W W R R R R R R R R R R B B B
Abbreviation
B Buttwelding Tee
2 274/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A HGO2 HGOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 150 A312-TP304/304L SMLS BE SCH80S
200 - 300 A312-TP304/304L SMLS BE SCH100
350 - 600 A312-TP304/304L DSAW BE SCH120
NIPPLE
15 - 150 A312-TP304/304L SMLS BBE SCH80S L=3"
BEND (02,103)
SWAGE (02,103)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
FLANGE (02,103)
15 - 50 A182-F304/304L 1500# WN RTJ
80 - 600 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 600 A182-F304/304L 900# WN RTJ WITH J.B
BLIND FLANGE (103)
15 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 600 A182-F304/304L 900# BLIND RTJ
LINE BLANK
15 - 50 A240-304/304L 1500# FIG-8 RTJ
80 - 150 A240-304/304L 900# FIG-8 RTJ
200 - 600 A240-304/304L 900# BLK&SPC RTJ
GASKET
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
BOLT/NUT
2 275/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A HGO2 HGOX(NOTE 102,103) PWHT / NACE Not required
- LICENSOR B
GATE
15 - 40 A182-F316/ALLOY400 1500# RTJ BB OS&Y (GA-223) (08-3,09)
50 - 50 A351-CF8M/ALLOY400 1500# RTJ BB OS&Y (GA-223A) (08-3,09)
80 - 150 A351-CF8M/ALLOY400 900# RTJ BB OS&Y (GA-224) (08-3,09)
200 - 600 A351-CF8M/ALLOY400 900# RTJ BB OS&Y GEAR (GA-225) (08-3,09)
(GA-224)
WITH BY
80 - 80 A351-CF8M/ALLOY400 900# RTJ BB OS&Y PASS DN15 (08-3,09)
GLOBE V/V
(GL-223)
GLOBE
15 - 40 A182-F316/ALLOY400 1500# RTJ BB OS&Y (GL-223) (08-3,09)
50 - 50 A351-CF8M/ALLOY400 1500# RTJ BB OS&Y (GL-223A) (08-3,09)
80 - 100 A351-CF8M/ALLOY400 900# RTJ BB OS&Y (GL-224) (08-3,09)
150 - 600 A351-CF8M/ALLOY400 900# RTJ BB OS&Y GEAR (GL-225) (08-3,09)
CHECK
15 - 40 A182-F316/ALLOY400 1500# RTJ BC SWING (CH-246) (62)
50 - 50 A351-CF8M/ALLOY400 1500# RTJ BC SWING (CH-246A) (62)
80 - 600 A351-CF8M/ALLOY400 900# RTJ BC SWING (CH-244) (62)
80 - 600 A351-CF8M/ALLOY400 900# RTJ WAFER DUAL PLATE (CH-245) (07,26,63)
BALL
80 - 80 A351-CF8M/ALLOY400 900# RTJ FULL BORE F.S (BA-244) (08-3,09)
100 - 600 A351-CF8M/ALLOY400 900# RTJ FULL BORE F.S GEAR (BA-245) (08-3,09)
Note :
09
102
2 276/334
CLASS: 09C0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 277/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B
PIPE (01,110)
25 - 80 A312-TP304/304L SMLS BE SCH160
100 - 300 A312-TP304/304L SMLS BE SCH120
BEND (02,114)
25 - 50 A312-TP304/304L SMLS BE XXS 3D (110,111)
80 - 200 A312-TP304/304L SMLS BE SCH160 3D (110,111)
25 - 50 A312-TP304/304L SMLS BE XXS 5D (110,111)
80 - 200 A312-TP304/304L SMLS BE SCH160 5D (110,111)
NIPPLE (02,114)
SWAGE (02,114)
ELBOW/TEE/REDUCER/CAP/LATERAL (02,114)
15 - 80 A182-F304/304L 900# RTJ To match pipe thickness
THREDOLET (163)
25 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
25 - 40 A182-F304/304L THRD HEX
FLANGE (02)
25 - 50 A182-F304/304L 1500# WN RTJ
80 - 300 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 300 A182-F304/304L 900# WN RTJ WITH J.B
80 - 300 A182-F304/304L 900# WN RF (82)
125 - 125 A105 900# LJ RF
BLIND FLANGE
25 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 300 A182-F304/304L 900# BLIND RTJ
GASKET
25 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 300 SS304/304L 900# RTJ OVAL RING
80 - 300 SW(304+GRAP)IO:304 900# RF 4.5MM (82)
125 - 125 SW(304+GRAP)IO:304 1500# RF 4.5MM
BOLT/NUT
A193-B7/A194-2H STUD/H.HEX
2 278/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B
GATE
15 - 40 A105/13Cr+HF 1500# RTJ BB OS&Y (GA-130A) (08,09)
50 - 50 A216-WCB/13Cr+HF 1500# RTJ BB OS&Y (GA-130) (08,09)
80 - 150 A216-WCB/13Cr+HF 900# RTJ BB OS&Y (GA-131) (08,09)
CHECK
50 - 50 A216-WCB/13Cr+HF 1500# RTJ LUG DUAL PLATE (CH-119) (08,09)
80 - 150 A216-WCB/13Cr+HF 900# RTJ LUG DUAL PLATE (CH-120) (08,09)
BALL
25 - 50 A351-CF8M/Cr Pl.SS+METAL 1500# RTJ FULL BORE F.S (BA-280) (08,09)
80 - 80 A351-CF8M/Cr Pl.SS+METAL 900# RTJ FULL BORE F.S (BA-281) (08,09)
100 - 200 A351-CF8M/Cr Pl.SS+METAL 900# RTJ FULL BORE F.S GEAR (BA-282) (08,09)
25 - 50 A351-CF8M/Cr Pl.SS+METAL 1500# RTJ FULL F.S EXT.BONNET (BA-280E)
Note :
08
09
110
111
2 279/334
CLASS: 09C2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 280/334
CLASS: 09C2 (45°)
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 LT
20 LT LT
25 LT LT LT
Header Size (DN)
40 LT LT LT LT
50 LO LO LO LT LT
Abbreviation
LT Lateral Tee
LO Latrolet
2 281/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A HBFW PWHT / NACE Reqd per B31.3 Sec 331
PIPE (01)
15 - 20 A106-B SMLS PE SCH160
25 - 40 A106-B SMLS PE SCH80
50 - 50 A106-B SMLS BE 6.35MM
80 - 80 A106-B SMLS BE SCH80
100 - 150 A106-B SMLS BE SCH120
200 - 600 A106-B SMLS BE SCH120
NIPPLE (02,03-2)
SWAGE (02,03-2)
15 - 40 A105 SW 6000#
CAP (02)
15 - 40 A105 SW 6000#
15 - 40 A105 SW 6000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS
15 - 40 A105 THRD HEX
WELDOLET (02)
FLANGE (02)
15 - 40 A105 1500# SW RTJ
50 - 50 A105 1500# WN RTJ
80 - 600 A105 900# WN RTJ
50 - 50 A105 1500# WN RTJ WITH J.B
80 - 600 A105 900# WN RTJ WITH J.B
80 - 80 A105 1500# WN RTJ (82)
BLIND FLANGE
15 - 50 A105 1500# BLIND RTJ
80 - 600 A105 900# BLIND RTJ
LINE BLANK
15 - 50 A105 1500# FIG-8 RTJ
80 - 150 A105 900# FIG-8 RTJ
200 - 600 A105 900# BLK&SPC RTJ
GASKET
BOLT/NUT
2 282/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A HBFW PWHT / NACE Reqd per B31.3 Sec 331
GATE
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GA-117) (09)
50 - 50 A216-WCB/S&D HF 1500# RTJ BB OS&Y (GA-122) (09,15)
200 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR (GA-119) (09,15)
15 - 40 A105/S&D HF 1500# RTJ BB OS&Y (GA-116) (09,15)
(GA-118A)
MECHANIC
150 - 150 A216-WCB/S&D HF 900# RTJ BB OS&Y AL STOP
MINIMUM
10%
GLOBE
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GL-109) (09)
50 - 50 A216-WCB/S&D HF 1500# RTJ BB OS&Y (GL-121) (09)
150 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR (GL-123) (09)
CHECK
50 - 50 A216-WCB/S&D HF 1500# RTJ BC SWING (CH-112) (62)
50 - 50 A216-WCB/S&D HF 1500# RTJ BCBALL (CH-112A)
80 - 600 A216-WCB/S&D HF 900# RTJ BCBALL (CH-111A)
STOP CHECK
REFERENCE
80 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y
(CH-111)
BALL
15 - 50 A216-WCB/316+RTFE 1500# RTJ RED. BORE F.S (BA-127) (09)
100 - 600 A216-WCB/316+RTFE 900# RTJ RED. BORE F.S GEAR (BA-130) (09)
80 - 80 A216-WCB/316+RTFE 900# RTJ FULL BORE F.S (BA-129) (08-2,09)
100 - 600 A216-WCB/316+RTFE 900# RTJ FULL BORE F.S GEAR (BA-131) (08-2,09)
Note :
03-2
09
35
323.2.2 of ASME B31.3.
2 283/334
CLASS: 09CS1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S B B B
150 S S S S W B B B
250 S S S S W W B B B B
300 S S S S W W W B B B B
350 S S S S W W W B B B B B
400 S S S S W W W B B B B B B
450 S S S S W W W W B B B B B B
500 S S S S W W W W B B B B B B B
600 S S S S W W W W W B B B B B B B
Abbreviation

Buttwelding Tee
2 284/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A BDH,HC,HS PWHT / NACE Reqd per B31.3 Sec 331
PIPE (01)
15 - 15 A106-B SMLS PE XXS
20 - 40 A106-B SMLS PE SCH160
50 - 80 A106-B SMLS BE SCH160
100 - 100 A106-B SMLS BE SCH120
150 - 150 A106-B SMLS BE 15.88MM
200 - 200 A106-B SMLS BE SCH120
250 - 250 A106-B SMLS BE 22.23MM
300 - 600 A106-B SMLS BE SCH120
NIPPLE (02,03-2)
15 - 40 A106-B SMLS PBE To match pipe thickness L=3"
SWAGE (02,03-2)
15 - 40 A105 SW 6000#
CAP (02)
15 - 40 A105 THRD 6000#
WELDOLET (02,05)
15 - 40 A105 SW 6000#
THREDOLET (163)
15 - 40 A105 THRD 6000#
PLUGS (02)
15 - 40 A105 THRD HEX
FLANGE (02)
15 - 40 A105 1500# SW RTJ
50 - 50 A105 1500# WN RTJ
80 - 600 A105 900# WN RTJ
50 - 50 A105 1500# WN RTJ WITH J.B
80 - 600 A105 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A105 1500# BLIND RTJ
80 - 600 A105 900# BLIND RTJ
LINE BLANK
15 - 50 A105 1500# FIG-8 RTJ
80 - 150 A105 900# FIG-8 RTJ
200 - 600 A105 900# BLK&SPC RTJ
GASKET
BOLT/NUT
2 285/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A BDH,HC,HS PWHT / NACE Reqd per B31.3 Sec 331
GATE
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GA-117) (09)
200 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR (GA-119) (09,15)
WITH BY PASS
350 - 350 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR DN20 GLOBE (09,15)
V/V (GA-119)
15 - 40 A105/S&D HF 1500# RTJ BB OS&Y (GA-116) (09,15)
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GA-117A) (08-2,09)
GLOBE
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GL-109) (09)
150 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR (GL-123) (09)
CHECK
50 - 80 A216-WCB/S&D HF 1500# RTJ BC BALL (CH-112A)
STOP CHECK
REFERENCE
80 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y
(CH-111)
BALL
15 - 50 A216-WCB/316+HF 1500# RTJ RED. BORE F.S (BA-149) (09)
100 - 600 A216-WCB/316+HF 900# RTJ RED. BORE F.S GEAR (BA-152) (09)
80 - 80 A216-WCB/316+HF 900# RTJ FULL BORE F.S (BA-151) (08-2,09)
100 - 600 A216-WCB/316+HF 900# RTJ FULL BORE F.S GEAR (BA-153) (08-2,09)
Note :
03-2
05
09
35
323.2.2 of ASME B31.3.
2 286/334
CLASS: 09CS2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S B B B
150 S S S S W B B B
Abbreviation

Buttwelding Tee
2 287/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B HS for thk > 12.70mm
PIPE (01)
15 - 80 A335-P11 SMLS BE SCH160
100 - 600 A335-P11 SMLS BE SCH120
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A182-F11-Cl.2 THRD 3000#
PLUGS (163)
15 - 40 A182-F11-Cl.2 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 50 A182-F11-Cl.2 1500# WN RTJ
80 - 600 A182-F11-Cl.2 900# WN RTJ
50 - 50 A182-F11-Cl.2 1500# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F11-Cl.2 1500# BLIND RTJ
80 - 600 A182-F11-Cl.2 900# BLIND RTJ
LINE BLANK
15 - 50 A182-F11-Cl.2 1500# FIG-8 RTJ
80 - 150 A182-F11-Cl.2 900# FIG-8 RTJ
200 - 600 A182-F11-Cl.2 900# BLK&SPC RTJ
GASKET
15 - 50 5CR-0.5MO 1500# RTJ OVAL RING
BOLT/NUT
2 288/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B HS for thk > 12.70mm
GATE
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BB OS&Y (GA-711) (08-2,09)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BB OS&Y (GA-711A) (08-2,09)
80 - 150 A217-WC6/13Cr+HF 900# RTJ BB OS&Y (GA-712) (08-2,09)
200 - 600 A217-WC6/13Cr+HF 900# RTJ BB OS&Y GEAR (GA-714) (08-2,09)
80 - 150 A217-WC6/13Cr+HF 900# BW BB OS&Y (GA-713) (08-2,09)
200 - 600 A217-WC6/13Cr+HF 900# BW BB OS&Y GEAR (GA-715) (08-2,09)
GLOBE
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BB OS&Y (GL-711) (09)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BB OS&Y (GL-711A) (09)
80 - 100 A217-WC6/13Cr+HF 900# RTJ BB OS&Y (GL-712) (09)
150 - 300 A217-WC6/13Cr+HF 900# RTJ BB OS&Y GEAR (GL-713) (09)
CHECK
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BC LIFT (CH-711) (61)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BC SWING (CH-711A)
80 - 600 A217-WC6/13Cr+HF 900# RTJ BC SWING (CH-713)
80 - 600 A217-WC6/13Cr 900# LUG DUAL PLATE (CH-712) (62)
BALL
15 - 50 A217-WC6/316+HF 1500# RTJ RED. BORE F.S (BA-711) (09)
100 - 600 A217-WC6/316+HF 900# RTJ RED. BORE F.S GEAR (BA-714) (09)
80 - 80 A217-WC6/316+HF 900# RTJ FULL BORE F.S (BA-713) (08-2,09)
100 - 600 A217-WC6/316+HF 900# RTJ FULL BORE F.S GEAR (BA-715) (08-2,09)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 289/334
CLASS: 09E1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 290/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B HSSS for thk > 12.70mm
PIPE (01)
15 - 20 A335-P11 SMLS BE XXS
25 - 150 A335-P11 SMLS BE SCH160
200 - 400 A335-P11 SMLS BE SCH140
450 - 450 A335-P11 SMLS BE SCH120
500 - 500 A335-P11 SMLS BE SCH140
600 - 600 A335-P11 SMLS BE SCH120
NIPPLE (02,03)
SWAGE (02,03)
THREDOLET (163)
15 - 40 A182-F11-Cl.2 THRD 6000#
PLUGS (163)
15 - 40 A182-F11-Cl.2 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 50 A182-F11-Cl.2 1500# WN RTJ
80 - 600 A182-F11-Cl.2 900# WN RTJ
200 - 400 A182-F11-Cl.2 1500# WN RTJ (82)
BLIND FLANGE
15 - 50 A182-F11-Cl.2 1500# BLIND RTJ
80 - 600 A182-F11-Cl.2 900# BLIND RTJ
LINE BLANK
15 - 50 A182-F11-Cl.2 1500# FIG-8 RTJ
80 - 150 A182-F11-Cl.2 900# FIG-8 RTJ
200 - 600 A182-F11-Cl.2 900# BLK&SPC RTJ
GASKET
BOLT/NUT
2 291/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B HSSS for thk > 12.70mm
GATE
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BB OS&Y (GA-711) (08-2,09)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BB OS&Y (GA-711A) (08-2,09)
80 - 150 A217-WC6/13Cr+HF 900# RTJ BB OS&Y (GA-712) (08-2,09)
200 - 600 A217-WC6/13Cr+HF 900# RTJ BB OS&Y GEAR (GA-714) (08-2,09)
80 - 150 A217-WC6/13Cr+HF 900# BW BB OS&Y (GA-713) (08-2,09)
200 - 600 A217-WC6/13Cr+HF 900# BW BB OS&Y GEAR (GA-715) (08-2,09)
GLOBE
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BB OS&Y (GL-711) (09)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BB OS&Y (GL-711A) (09)
80 - 100 A217-WC6/13Cr+HF 900# RTJ BB OS&Y (GL-712) (09)
150 - 300 A217-WC6/13Cr+HF 900# RTJ BB OS&Y GEAR (GL-713) (09)
CHECK
15 - 40 A182-F11-Cl.2/13Cr+HF 1500# RTJ BC LIFT (CH-711) (61)
50 - 50 A217-WC6/13Cr+HF 1500# RTJ BC SWING (CH-711A)
80 - 600 A217-WC6/13Cr+HF 900# RTJ BC SWING (CH-713)
80 - 600 A217-WC6/13Cr 900# LUG DUAL PLATE (CH-712) (62)
BALL
100 - 600 A217-WC6/316+HF 900# RTJ RED. BORE F.S GEAR (BA-714) (09)
80 - 80 A217-WC6/316+HF 900# RTJ FULL BORE F.S (BA-713) (08-2,09)
100 - 600 A217-WC6/316+HF 900# RTJ FULL BORE F.S GEAR (BA-715) (08-2,09)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 292/334
CLASS: 09E2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 293/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A WOX, HGO2(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 20 A312-TP310 SMLS BE SCH160
25 - 80 A312-TP310 SMLS BE SCH80S
100 - 150 A312-TP310 SMLS BE SCH120
200 - 300 A312-TP310 SMLS BE SCH100
BEND (02,103)
15 - 300 A312-TP310 SMLS BE To match pipe thickness 3D
SWAGE (02,103)
NIPPLE (02,103)
ELBOW/TEE/CAP/REDUCER (02,103)
THREDOLET (163)
15 - 40 A182-F310 THRD 3000#
PLUGS (163)
15 - 40 A182-F310 THRD HEX
FLANGE (02,103)
15 - 50 A182-F310 1500# WN RTJ
80 - 300 A182-F310 900# WN RTJ
50 - 50 A182-F310 1500# WN RTJ WITH J.B
80 - 300 A182-F310 900# WN RTJ WITH J.B
200 - 300 A182-F310 900# WN RF (82)
BLIND FLANGE (103)
15 - 50 A182-F310 1500# BLIND RTJ
80 - 300 A182-F310 900# BLIND RTJ
GASKET
15 - 50 SS310 1500# RTJ OVAL RING
80 - 300 SS310 900# RTJ OVAL RING
200 - 300 SW(310+GRAP)IO:310 900# RF 4.5MM (82,103,105)
BOLT/NUT
GATE
15 - 50 A494-M35-1/MONEL 1500# RTJ BB OS&Y (GA-231) (08,08-3,09)
80 - 150 A494-M35-1/MONEL 900# RTJ BB OS&Y (GA-232) (08,08-3,09)
CHECK
15 - 50 A494-M35-1/MONEL 1500# RTJ BC SWING (CH-262) (08-3,09,61)
80 - 250 A494-M35-1/MONEL 900# RTJ WAFER DUAL PLATE (CH-264) (08,08-3,09)
REFERENCE
50 - 50 A494-M35-1/MONEL 1500# RTJ BC BALL (CH-262)
BALL
15 - 50 A351-CF8M/MONEL+RTFE 1500# RTJ FULL BORE F.S (BA-262) (08,08-3,09)
80 - 80 A351-CF8M/MONEL+RTFE 900# RTJ FULL BORE F.S (BA-263) (08,08-3,09)
100 - 200 A351-CF8M/MONEL+RTFE 900# RTJ FULL BORE F.S GEAR (BA-264) (08,08-3,09)
15 - 50 A351-CF8M/MONEL+RTFE 1500# RTJ FULL F.S EXT.BONNET (BA-262E)
15 - 50 A351-CF8M/MONEL 1500# RTJ FULL BORE F.S (BA-262A) (08,08-3,09)
80 - 80 A351-CF8M/MONEL 900# RTJ FULL BORE F.S (BA-263A) (08,08-3,09)
100 - 200 A351-CF8M/MONEL 900# RTJ FULL BORE F.S GEAR (BA-264A) (08,08-3,09)
2 294/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A WOX, HGO2(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
Note :
08
09
102
2 295/334
CLASS: 09J1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 296/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL
PIPE (01)
15 - 100 A312-TP321 SMLS BE SCH80S
150 - 600 A312-TP321 SMLS BE SCH120
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F321 THRD 3000#
PLUGS (163)
15 - 40 A182-F321 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 50 A182-F321 1500# WN RTJ
80 - 600 A182-F321 900# WN RTJ
50 - 50 A182-F321 1500# WN RTJ WITH J.B
80 - 600 A182-F321 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F321 1500# BLIND RTJ
80 - 600 A182-F321 900# BLIND RTJ
LINE BLANK
15 - 50 A182-F321 1500# FIG-8 RTJ
80 - 150 A182-F321 900# FIG-8 RTJ
200 - 600 A182-F321 900# BLK&SPC RTJ
GASKET
15 - 50 SS321 1500# RTJ OVAL RING
80 - 600 SS321 900# RTJ OVAL RING
BOLT/NUT
2 297/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL
GATE
EXTENDED
15 - 40 A182-F321/S&D HF 1500# RTJ BB OS&Y BONNET (08-2,09)
(GA-510)
EXTENDED
50 - 50 A351-321SS/S&D HF 1500# RTJ BB OS&Y BONNET (08-2,09)
(GA-510A)
EXTENDED
80 - 150 A351-321SS/S&D HF 900# RTJ BB OS&Y BONNET (08-2,09)
(GA-511)
EXTENDED
200 - 600 A351-321SS/S&D HF 900# RTJ BB OS&Y GEAR BONNET (08-2,09)
(GA-513)
EXTENDED
80 - 150 A351-321SS/S&D HF 900# BW BB OS&Y BONNET (08-2,09)
(GA-512)
EXTENDED
200 - 600 A351-321SS/S&D HF 900# BW BB OS&Y GEAR BONNET (08-2,09)
(GA-514)
GLOBE
EXTENDED
15 - 40 A182-F321/S&D HF 1500# RTJ BB OS&Y BONNET (09)
(GL-510)
EXTENDED
50 - 50 A351-321SS/S&D HF 1500# RTJ BB OS&Y BONNET (09)
(GL-510A)
EXTENDED
80 - 100 A351-321SS/S&D HF 900# RTJ BB OS&Y BONNET (09)
(GL-511)
EXTENDED
150 - 300 A351-321SS/S&D HF 900# RTJ BB OS&Y GEAR BONNET (09)
(GL-512)
CHECK
15 - 40 A182-F321/S&D HF 1500# BW BC LIFT (CH-510) (61)
50 - 50 A351-321SS/S&D HF 1500# BW BC LIFT (CH-510A) (61)
80 - 600 A351-321SS/S&D HF 900# RTJ BC SWING (CH-511) (62)
BALL
EXTENDED
15 - 50 A182-F321/321+RTFE 1500# BW RED. BORE F.S BONNET (09)
(BA-510)
EXTENDED
80 - 80 A351-321SS/321+RTFE 900# RTJ RED. BORE F.S BONNET (09)
(BA-511)
EXTENDED
100 - 600 A351-321SS/321+RTFE 900# RTJ RED. BORE F.S GEAR BONNET (09)
(BA-513)
EXTENDED
80 - 80 A351-321SS/321+RTFE 900# RTJ FULL BORE F.S BONNET (08-2,09)
(BA-512)
EXTENDED
100 - 600 A351-321SS/321+RTFE 900# RTJ FULL BORE F.S GEAR BONNET (08-2,09)
(BA-514)
2 298/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL
Note :
05
09
35
323.2.2 of ASME B31.3.
2 299/334
CLASS: 09L0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 300/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A GOX, HGO2, HGOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
200 - 200 B165-N04400 SMLS BE SCH100 ANNEALED
ANNEALED
250 - 300 B725-N04400 SMLS BE SCH100 CATEGORY-2
ANNEALED
350 - 600 B725-N04400 DSAW BE SCH120 CATEGORY-2
NIPPLE
ANNEALED
To match pipe thickness
15 - 150 B165-N04400 SMLS BBE L=3"
BEND (02,103)
ANNEALED
3D
15 - 150 B165-N04400 SMLS BE
ANNEALED
3D
200 - 200 B165-N04400 SMLS BE
ANNEALED
250 - 300 B725-N04400 SMLS BE To match pipe thickness CATEGORY-2
3D
ANNEALED
350 - 600 B725-N04400 DSAW BE To match pipe thickness CATEGORY-2
3D
350 - 600 B366-WPNC-W WELD BW To match pipe thickness ANNEALED
CAP (02,103)
50 - 600 B564-N04400 BW To match pipe thickness ANNEALED
FLANGE (02,103)
15 - 50 B564-N04400 1500# WN RTJ ANNEALED
80 - 600 B564-N04400 900# WN RTJ ANNEALED
WITH J.B
50 - 50 B564-N04400 1500# WN RTJ
ANNEALED
WITH J.B
80 - 600 B564-N04400 900# WN RTJ
ANNEALED
BLIND FLANGE (103)
15 - 50 B564-N04400 1500# BLIND RTJ ANNEALED
80 - 600 A105(B127-N04400 3.2MM PLATED) 900# BLIND RTJ
GASKET
15 - 50 ALLOY 400 1500# RTJ OVAL RING (104)
80 - 600 ALLOY 400 900# RTJ OVAL RING (104)
BOLT/NUT
2 301/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A GOX, HGO2, HGOX(NOTE 58,102,103) PWHT / NACE Not required
- LICENSOR B
GATE
15 - 50 ALLOY400/ALLOY400+HF 1500# RTJ BB OS&Y (GA-304) (08-3,09,99,103)
80 - 150 ALLOY400/ALLOY400+HF 900# RTJ BB OS&Y (GA-305) (08-3,09,99,103)
200 - 600 ALLOY400/ALLOY400+HF 900# RTJ BB OS&Y GEAR (GA-306) (08-3,09,99,103)
GLOBE
15 - 50 ALLOY400/ALLOY400+HF 1500# RTJ BB OS&Y (GL-305)
80 - 100 ALLOY400/ALLOY400+HF 900# RTJ BB OS&Y (GL-306) (08-3,09,99,103)
150 - 300 ALLOY400/ALLOY400+HF 900# RTJ BB OS&Y GEAR (GL-307) (08-3,09,99,103)
CHECK
15 - 50 ALLOY400/ALLOY400+HF 1500# RTJ BC SWING (CH-305) (62)
80 - 600 ALLOY400/ALLOY400+HF 900# RTJ BC SWING (CH-306) (62)
80 - 600 ALLOY400/ALLOY400+HF 900# RTJ WAFER DUAL PLATE (CH-307) (07,26,63)
BALL
15 - 50 ALLOY400/ALLOY400+HF 1500# RTJ FULL BORE F.S (BA-305) (08-3,09,99,103)
80 - 80 ALLOY400/ALLOY400+HF 900# RTJ FULL BORE F.S (BA-306) (08-3,09,99,103)
100 - 600 ALLOY400/ALLOY400+HF 900# RTJ FULL BORE F.S GEAR (BA-307) (08-3,09,99,103)
Note :
09
102
2 302/334
CLASS: 09NM
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 303/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A SPW,MPW PWHT / NACE Not required
- LICENSOR B
PIPE (01,99,103)
15 - 150 A312-TP304/304L SMLS BE SCH80S
200 - 300 A312-TP304/304L SMLS BE SCH100
350 - 600 A312-TP304/304L DSAW BE SCH120
NIPPLE
15 - 40 A312-TP304/304L SMLS BBE SCH80S L=3"
SWAGE (02)
CAP (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 50 A182-F304/304L 1500# WN RTJ
80 - 600 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 600 A182-F304/304L 900# WN RTJ WITH J.B
80 - 80 A182-F304/304L 1500# WN RTJ
15 - 50 A182-F304/304L 1500# WN RF
BLIND FLANGE
15 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 600 A182-F304/304L 900# BLIND RTJ
LINE BLANK
50 - 50 A182-F304/304L 1500# FIG-8 RTJ
GASKET
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
80 - 80 SS304/304L 1500# RTJ OVAL RING
15 - 50 SW(304+GRAP)IO:304 1500# RF 4.5MM
BOLT/NUT
2 304/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B
GATE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GA-213) (09)
50 - 50 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GA-213A) (09)
80 - 150 A351-CF8M/316+HF 900# RTJ BB OS&Y (GA-211) (09)
200 - 600 A351-CF8M/316+HF 900# RTJ BB OS&Y GEAR (GA-212) (09)
GLOBE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GL-211) (09)
50 - 50 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GL-211A) (09)
80 - 100 A351-CF8M/316+HF 900# RTJ BB OS&Y (GL-209) (09)
150 - 600 A351-CF8M/316+HF 900# RTJ BB OS&Y GEAR (GL-210) (09)
CHECK
15 - 40 A182-F316/316+HF 1500# BW BC LIFT (CH-210) (61)
50 - 50 A351-CF8M/316+HF 1500# RTJ BC SWING (CH-210A) (62)
80 - 600 A351-CF8M/316+HF 900# RTJ BC SWING (CH-212) (62)
80 - 600 A351-CF8M/316+HF 900# RTJ WAFER DUAL PLATE (CH-211) (07,26,63)
BALL
15 - 40 A351-CF8M/316+RTFE 1500# BW RED. BORE F.S (BA-224) (09)
50 - 50 A351-CF8M/316+RTFE 1500# RTJ RED. BORE F.S (BA-225) (09)
100 - 600 A351-CF8M/316+RTFE 900# RTJ RED. BORE F.S GEAR (BA-227) (09)
80 - 80 A351-CF8M/316+RTFE 900# RTJ FULL BORE F.S (BA-226) (08-2,09)
100 - 600 A351-CF8M/316+RTFE 900# RTJ FULL BORE F.S GEAR (BA-228) (08-2,09)
Note :
09
2 305/334
CLASS: 09SS
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 306/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 09U0(Added)
RATING ASME 900#
- LICENSOR A RECL,PGM,PCHM PWHT / NACE Not required
- LICENSOR B
PIPE (01)
15 - 150 A312-TP304/304L SMLS BE SCH80S
200 - 300 A312-TP304/304L SMLS BE SCH100
350 - 400 A358-304/304L-Cl.1 EFW BE SCH80
450 - 450 A358-304/304L-Cl.1 EFW BE 25.40MM
500 - 500 A358-304/304L-Cl.1 EFW BE 28.58MM
600 - 600 A358-304/304L-Cl.1 EFW BE 33.32MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 50 A182-F304/304L 1500# WN RTJ
80 - 600 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 600 A182-F304/304L 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 600 A182-F304/304L 900# BLIND RTJ
LINE BLANK
15 - 50 A240-304/304L 1500# FIG-8 RTJ
80 - 150 A240-304/304L 900# FIG-8 RTJ
200 - 600 A240-304/304L 900# BLK&SPC RTJ
GASKET
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
BOLT/NUT
2 307/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 09U0(Added)
RATING ASME 900#
- LICENSOR A RECL,PGM,PCHM PWHT / NACE Not required
- LICENSOR B
VALVES FOR FLUIDS : (Operating between -46℃ and 300℃)
GATE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GA-213) (09)
GLOBE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GL-211) (09)
80 - 100 A351-CF8M/316 900# RTJ BB OS&Y (GL-209) (09)
150 - 300 A351-CF8M/316 900# RTJ BB OS&Y GEAR (GL-210) (09)
CHECK
15 - 40 A182-F316/316+HF 1500# BW BC LIFT (CH-210) (61)
80 - 600 A351-CF8M/316 900# RTJ BC SWING (CH-234) (62)
BALL
15 - 50 A351-CF8M/316+RTFE 1500# RTJ RED. F.S EXT.BONNET (BA-229E)
15 - 50 A351-CF8M/316+RTFE 1500# RTJ FULL BORE F.S (BA-230) (09)
Note :
09
62 These check valves shall be installed in a horizontal position with cover up or in a vertical position with upward flow. Integrally
81 reinforced branch connections, tees, and reducing tees are permitted as an acceptable alternative branch connection. These items
163 shall be used only for hydrotest vent/drain.
2 308/334
CLASS: 09U0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 309/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL,PGM,PCHM
PIPE (01)
15 - 150 A312-TP304/304L SMLS BE SCH80S
200 - 300 A312-TP304/304L SMLS BE SCH100
350 - 400 A358-304/304L-Cl.1 EFW BE SCH80
450 - 450 A358-304/304L-Cl.1 EFW BE 25.40MM
500 - 500 A358-304/304L-Cl.1 EFW BE 28.58MM
600 - 600 A358-304/304L-Cl.1 EFW BE 33.32MM
NIPPLE (02)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 50 A182-F304/304L 1500# WN RTJ
80 - 600 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 600 A182-F304/304L 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 600 A182-F304/304L 900# BLIND RTJ
LINE BLANK
15 - 50 A240-304/304L 1500# FIG-8 RTJ
80 - 150 A240-304/304L 900# FIG-8 RTJ
200 - 600 A240-304/304L 900# BLK&SPC RTJ
GASKET
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
BOLT/NUT
2 310/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
VALVES FOR FLUIDS : (Operating between -46℃ and 300℃)
GATE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GA-213) (09)
GLOBE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GL-211) (09)
80 - 100 A351-CF8M/316 900# RTJ BB OS&Y (GL-209) (09)
150 - 300 A351-CF8M/316 900# RTJ BB OS&Y GEAR (GL-210) (09)
CHECK
15 - 40 A182-F316/316+HF 1500# BW BC LIFT (CH-210) (61)
BALL
15 - 50 A351-CF8M/316+RTFE 1500# RTJ RED. F.S EXT.BONNET (BA-229E)
Note :
09
62 These check valves shall be installed in a horizontal position with cover up or in a vertical position with upward flow. Integrally
81 reinforced branch connections, tees, and reducing tees are permitted as an acceptable alternative branch connection. These items
163 shall be used only for hydrotest vent/drain.
2 311/334
CLASS: 09U0B
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 312/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
PIPE (01)
15 - 150 A312-TP304/304L SMLS BE SCH80S
200 - 300 A312-TP304/304L SMLS BE SCH100
350 - 400 A358-304/304L-Cl.1 EFW BE SCH80
450 - 450 A358-304/304L-Cl.1 EFW BE 25.40MM
500 - 500 A358-304/304L-Cl.1 EFW BE 28.58MM
600 - 600 A358-304/304L-Cl.1 EFW BE 33.32MM
NIPPLE (02)
SWAGE (02)
CAP (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 50 A182-F304/304L 1500# WN RTJ
80 - 600 A182-F304/304L 900# WN RTJ
50 - 50 A182-F304/304L 1500# WN RTJ WITH J.B
80 - 600 A182-F304/304L 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F304/304L 1500# BLIND RTJ
80 - 600 A182-F304/304L 900# BLIND RTJ
LINE BLANK
15 - 50 A240-304/304L 1500# FIG-8 RTJ
80 - 150 A240-304/304L 900# FIG-8 RTJ
200 - 600 A240-304/304L 900# BLK&SPC RTJ
GASKET
15 - 50 SS304/304L 1500# RTJ OVAL RING
80 - 600 SS304/304L 900# RTJ OVAL RING
BOLT/NUT
2 313/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
VALVES FOR FLUIDS : (Operating below -46℃) IN CORROSIVE SERVICE
GATE
EXTENDED
15 - 40 A182-F316/316 1500# RTJ BB OS&Y BONNET (09)
(GA-366)
EXTENDED
50 - 50 A351-CF8M/316 1500# RTJ BB OS&Y BONNET
(GA-366A)
EXTENDED
80 - 150 A351-CF8M/316 900# RTJ BB OS&Y BONNET (09)
(GA-367)
EXTENDED
200 - 600 A351-CF8M/316 900# RTJ BB OS&Y GEAR BONNET (09)
(GA-368)
GLOBE
EXTENDED
15 - 40 A182-F316/316 1500# RTJ BB OS&Y BONNET (09)
(GL-366)
EXTENDED
50 - 50 A351-CF8M/316 1500# RTJ BB OS&Y BONNET
(GL-366A)
EXTENDED
80 - 100 A351-CF8M/316 900# RTJ BB OS&Y BONNET (09)
(GL-367)
EXTENDED
150 - 300 A351-CF8M/316 900# RTJ BB OS&Y GEAR BONNET (09)
(GL-368)
VALVES FOR FLUIDS : (Operating below -46℃) IN HIGHLY EXPLOSIVE SERVICE
GATE
EXTENDED
15 - 40 A182-F316/316 1500# RTJ BB OS&Y B.S BONNET (09)
(GA-391)
EXTENDED
50 - 50 A351-CF8M/316 1500# RTJ BB OS&Y B.S BONNET (09)
(GA-391A)
EXTENDED
(GA-392)
EXTENDED
BB OS&Y SPRING
100 - 150 A351-CF8M/316 900# RTJ BONNET (09)
LOADED
(GA-392)
EXTENDED
200 - 600 A351-CF8M/316 900# RTJ BB OS&Y SP.L GEAR BONNET (09)
(GA-393)
GLOBE
EXTENDED
15 - 40 A182-F316/316 1500# RTJ BB OS&Y B.S BONNET (09)
(GL-391)
EXTENDED
(GL-391A)
EXTENDED
(GL-392)
EXTENDED
BB OS&Y SPRING
100 - 100 A351-CF8M/316 900# RTJ BONNET (09)
LOADED
(GL-392)
EXTENDED
150 - 300 A351-CF8M/316 900# RTJ BB OS&Y SP.L GEAR BONNET (09)
(GL-393)
2 314/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
CHECK
15 - 40 A182-F316/316 1500# BW BC LIFT (CH-233) (61)
50 - 50 A351-CF8M/316 1500# RTJ BC SWING (CH-234A) (62)
80 - 600 A351-CF8M/316 900# LUG DUAL PLATE (CH-235) (07,26,63)
BALL
EXTENDED
15 - 50 A351-CF8M/316+RTFE 1500# RTJ RED. BORE F.S BONNET (09)
(BA-366)
EXTENDED
80 - 80 A351-CF8M/316+RTFE 900# RTJ RED. BORE F.S BONNET (09)
(BA-368)
EXTENDED
100 - 600 A351-CF8M/316+RTFE 900# RTJ RED. BORE F.S GEAR BONNET (09)
(BA-370)
EXTENDED
15 - 50 A351-CF8M/316+RTFE 1500# RTJ FULL BORE F.S BONNET (09)
(BA-367)
EXTENDED
80 - 80 A351-CF8M/316+RTFE 900# RTJ FULL BORE F.S BONNET (09)
(BA-369)
EXTENDED
100 - 600 A351-CF8M/316+RTFE 900# RTJ FULL BORE F.S GEAR BONNET (08-2,09)
(BA-371)
Note :
09
2 315/334
CLASS: 09U0C
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 316/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL,HCD,PGM,SNG for thk > 19.05mm
PIPE (01,27)
15 - 20 A106-B SMLS PE SCH160
25 - 40 A106-B SMLS PE SCH80
50 - 50 A106-B SMLS BE SCH160
80 - 80 A106-B SMLS BE SCH80
100 - 600 A106-B SMLS BE SCH120
250 - 250 A106-B(MONEL CLAD) SMLS BE SCH120
NIPPLE (02)
15 - 40 A106-B SMLS PBE To match pipe thickness L=3" (03)
15 - 40 A106-B SMLS POE/TOE To match pipe thickness L=3" (03)
SWAGE (02)
15 - 40 A105 SW 3000#
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
SOCKOLET/FULL COUPLING
15 - 40 A105 SW 3000#
FLANGE (02)
15 - 40 A105 1500# SW RTJ
50 - 50 A105 1500# WN RTJ
80 - 600 A105 900# WN RTJ
50 - 50 A105 1500# WN RTJ WITH J.B
80 - 600 A105 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A105 1500# BLIND RTJ
80 - 600 A105 900# BLIND RTJ
LINE BLANK
15 - 50 A105 1500# FIG-8 RTJ
80 - 150 A105 900# FIG-8 RTJ
200 - 600 A105 900# BLK&SPC RTJ
GASKET
BOLT/NUT
2 317/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR B RECL,HCD,PGM,SNG for thk > 19.05mm
GATE
15 - 40 A105/S&D HF 1500# RTJ BB OS&Y (GA-116) (08-2,09)
50 - 50 A216-WCB/S&D HF 1500# RTJ BB OS&Y (GA-122) (08-2,09)
80 - 150 A216-WCB/S&D HF 900# RTJ BB OS&Y (GA-118) (08-2,09)
200 - 600 A216-WCB/S&D HF 900# RTJ BB OS&Y GEAR (GA-119) (08-2,09)
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GA-117) (08-2,09)
(GA-120)
WITH BY
GLOBE V/V
(GL-109)
GLOBE
15 - 40 A105/S&D HF 1500# SW BB OS&Y (GL-109) (09)
50 - 50 A216-WCB/S&D HF 1500# BW BB OS&Y (GL-112) (09)
80 - 100 A216-WCB/S&D HF 900# BW BB OS&Y (GL-110) (09)
150 - 300 A216-WCB/S&D HF 900# BW BB OS&Y GEAR (GL-111) (09)
CHECK
80 - 600 A216-WCB/S&D HF 900# WAFER DUAL PLATE (CH-111B)
BALL
15 - 40 A216-WCB/316+RTFE 1500# SW RED. BORE F.S (BA-126) (09)
50 - 50 A216-WCB/316+RTFE 1500# BW RED. BORE F.S (BA-136) (09)
Note :
05
09
27
35
323.2.2 of ASME B31.3.
2 318/334
CLASS: 09X1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 F
20 F F
25 F F F
40 F F F F
50 S S S S B
80 S S S S B B
Header Size (DN)
100 S S S S B B B
150 S S S S W B B B
Abbreviation

Buttwelding Tee
2 319/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 900#
- LICENSOR A PCR,SGR PWHT / NACE Not required
- LICENSOR B
PIPE (01,100)
15 - 40 A790-S31803 SMLS BE SCH80S
50 - 150 A790-S31803 SMLS BE SCH40S
200 - 300 A790-S31803 SMLS BE SCH60
BEND
15 - 300 A790-S31803 SMLS BE To match pipe thickness 3D
SWAGE (02,114)
NIPPLE (02)
THREDOLET (163)
15 - 40 A182-F51 THRD 3000#
PLUGS (163)
15 - 40 A182-F51 THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 50 A182-F51 1500# WN RTJ
80 - 300 A182-F51 900# WN RTJ
50 - 50 A182-F51 1500# WN RTJ WITH J.B
80 - 300 A182-F51 900# WN RTJ WITH J.B
BLIND FLANGE
15 - 50 A182-F51 1500# BLIND RF
80 - 300 A182-F51 900# BLIND RF
GASKET
15 - 50 SS316L 1500# RTJ OVAL RING
80 - 300 SS316L 900# RTJ OVAL RING
BOLT/NUT
GATE
REFERENCE
15 - 40 A351-CD4MCu/DUPLEX 2205+HF 1500# RTJ BB OS&Y
(GA-620)
Note :
2 320/334
CLASS: 09Y0
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 321/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 1500#
TYPICAL SERVICE HBFW (Valves Buttwelded) DES. PRES.(barg) 255.3 to 143.8
PIPE (01,27)
15 - 80 A106-B SMLS BE SCH160
100 - 150 A106-B SMLS BE XXS
200 - 200 A106-B SMLS BE 25.40MM
250 - 250 A106-B SMLS BE 31.75MM
300 - 300 A671-CC65-Cl.22 EFW BE 31.75MM
350 - 350 A671-CC65-Cl.22 EFW BE 35.71MM
400 - 400 A671-CC65-Cl.22 EFW BE 40.49MM
450 - 450 A671-CC65-Cl.22 EFW BE 44.45MM
500 - 500 A671-CC65-Cl.22 EFW BE 50.80MM
600 - 600 A671-CC65-Cl.22 EFW BE 57.15MM
NIPPLE (02,03-2)
SWAGE (02,03-2)
THREDOLET (163)
15 - 40 A105 THRD 3000#
PLUGS (163)
15 - 40 A105 THRD HEX
WELDOLET (02,05)
FLANGE (02)
15 - 600 A105 1500# WN RTJ
50 - 600 A105 1500# WN RTJ WITH J.B
ORIFICE FLANGE
50 - 600 A105 1500# WN RTJ
BLIND FLANGE
15 - 600 A105 1500# BLIND RTJ
LINE BLANK
15 - 150 A105 1500# FIG-8 RTJ
200 - 600 A105 1500# BLK&SPC RTJ
GASKET
BOLT/NUT
2 322/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 1500#
TYPICAL SERVICE HBFW (Valves Buttwelded) DES. PRES.(barg) 255.3 to 143.8
GATE
15 - 40 A105/S&D HF 1500# RTJ BB OS&Y (GA-116) (15)
50 - 150 A216-WCB/S&D HF 1500# RTJ BB OS&Y (GA-122) (15)
200 - 600 A216-WCB/S&D HF 1500# RTJ BB OS&Y GEAR (GA-123) (15)
15 - 40 A105/S&D HF 1500# BW BB OS&Y (GA-147)
50 - 150 A216-WCB/S&D HF 1500# BW BB OS&Y (GA-124)
200 - 600 A216-WCB/S&D HF 1500# BW BB OS&Y (GA-125)
GLOBE
15 - 40 A105/S&D HF 1500# BW BB OS&Y (GL-120) (09)
50 - 100 A216-WCB/S&D HF 1500# BW PSB OS&Y (GL-112) (09)
150 - 300 A216-WCB/S&D HF 1500# BW PSB OS&Y GEAR (GL-113) (09)
CHECK
50 - 600 A216-WCB/S&D HF 1500# RTJ PSC SWING (CH-112) (62)
BALL
15 - 50 A216-WCB/316+RTFE 1500# BW RED. BORE F.S (BA-136) (09)
100 - 600 A216-WCB/316+HF 1500# RTJ RED. BORE F.S GEAR (BA-156) (09)
15 - 80 A216-WCB/316+HF 1500# BW RED. BORE F.S (BA-158) (09)
100 - 600 A216-WCB/316+HF 1500# BW RED. BORE F.S GEARREFERENCE (09)
(BA-158)
80 - 80 A216-WCB/316+HF 1500# RTJ FULL BORE F.S (BA-151) (08-2,09)
100 - 600 A216-WCB/316+HF 1500# RTJ FULL BORE F.S GEAR (BA-157) (08-2,09)
REFERENCE
80 - 80 A216-WCB/316+HF 1500# BW FULL BORE F.S (08-2,09)
(BA-151)
100 - 600 A216-WCB/316+HF 1500# BW FULL BORE F.S GEARREFERENCE (08-2,09)
(BA-157)
Note :
03-2
05
09
27
35
323.2.2 of ASME B31.3.
2 323/334
CLASS: 15CS1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 324/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15H1
RATING ASME 1500#
- LICENSOR B HSS,PGM
PIPE (01)
15 - 25 A335-P22(NACE) SMLS BE SCH160
40 - 150 A335-P22(NACE) SMLS BE XXS
200 - 200 A691-2.1/4CR-Cl.41(NACE) EFW BE 23.81MM
NIPPLE (02,03)
15 - 40 A335-P22(NACE) SMLS BBE To match pipe thickness L=3"
SWAGE (02,03)
15 - 100 A234-WP22-Cl.1(NACE) SMLS BBE To match pipe thickness
15 - 150 A234-WP22-Cl.1(NACE) SMLS BW To match pipe thickness
200 - 600 A234-WP22-Cl.1(NACE) WELD BW To match pipe thickness RT 100%
CAP (02)
15 - 600 A234-WP22-Cl.1(NACE) SMLS BW To match pipe thickness
THREDOLET (163)
15 - 40 A182-F22-Cl.3(NACE) THRD 3000#
PLUGS (163)
15 - 40 A182-F22-Cl.3(NACE) THRD HEX
WELDOLET (02,05)
80 - 600 A182-F22-Cl.3(NACE) BW To match pipe thickness
FLANGE (02)
15 - 600 A182-F22-Cl.3(NACE) 1500# WN RTJ
50 - 600 A182-F22-Cl.3(NACE) 1500# WN RTJ WITH J.B
BLIND FLANGE
15 - 600 A182-F22-Cl.3(NACE) 1500# BLIND RTJ
LINE BLANK
15 - 150 A182-F22-Cl.3(NACE) 1500# FIG-8 RTJ
200 - 600 A182-F22-Cl.3(NACE) 1500# BLK&SPC RTJ
GASKET
BOLT/NUT
A193-B16/A194-4(NACE) STUD/H.HEX Zn-CHROMATE
2 325/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15H1
RATING ASME 1500#
- LICENSOR B HSS,PGM
GATE
15 - 40 A182-F22-Cl.3(NACE)/S&D HF 1500# RTJ BB OS&Y (GA-720) (08-2,09)
50 - 100 A217-WC9(NACE)/S&D HF 1500# RTJ BB OS&Y (GA-722) (08-2,09)
150 - 600 A217-WC9(NACE)/S&D HF 1500# RTJ BB OS&Y GEAR (GA-724) (08-2,09)
15 - 40 A182-F22-Cl.3(NACE)/S&D HF 1500# BW BB OS&Y (GA-721) (08-2,09)
50 - 100 A217-WC9(NACE)/S&D HF 1500# BW BB OS&Y (GA-723) (08-2,09)
150 - 600 A217-WC9(NACE)/S&D HF 1500# BW BB OS&Y GEAR (GA-725) (08-2,09)
GLOBE
15 - 40 A182-F22-Cl.3(NACE)/S&D HF 1500# BW BB OS&Y (GL-720) (09)
50 - 300 A217-WC9(NACE)/S&D HF 1500# BW BB OS&Y GEAR (GL-721) (09)
CHECK
15 - 40 A182-F22-Cl.3(NACE)/S&D HF 1500# BW BC LIFT (CH-720) (61)
50 - 600 A217-WC9(NACE)/S&D HF 1500# RTJ BC SWING (CH-721) (62)
BALL
15 - 50 A217-WC9(NACE)/316+HF 1500# RTJ RED. BORE F.S (BA-720) (09)
80 - 600 A217-WC9(NACE)/316+HF 1500# RTJ RED. BORE F.S GEAR (BA-722) (09)
15 - 50 A217-WC9(NACE)/316+HF 1500# BW RED. BORE F.S (BA-721) (09)
80 - 600 A217-WC9(NACE)/316+HF 1500# BW FULL BORE F.S GEAR (BA-723) (08-2,09)
Note :
05
09
35
323.2.2 of ASME B31.3.
2 326/334
CLASS: 15H1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300 350 400 450 500 600
15 B
20 B B
25 B B B
40 B B B B
50 W B B B B
80 W W W B B B
Header Size (DN)
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 327/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15M2
RATING ASME 1500#
- LICENSOR A P PWHT / NACE Not required
- LICENSOR B
PIPE (01,109)
15 - 150 A312-TP304/304L SMLS BE XXS
200 - 200 A312-TP304/304L SMLS BE 25.40MM
250 - 250 A312-TP304/304L SMLS BE 31.75MM
300 - 300 A312-TP304/304L SMLS BE 38.10MM
BEND (02)
15 - 150 A312-TP304/304L SMLS BE XXS 10D (BASALT LINING) (109)
10D (BASALT LINING OF 100

200 - 200 A312-TP304/304L SMLS BE 25.40MM ID) (109)
10D (BASALT LINING OF

250 - 250 A312-TP304/304L SMLS BE 31.75MM
150 ID) (109)
300 - 300 A312-TP304/304L SMLS BE 38.10MM 10D (BASALT LINING) (109)

200 - 200 A312-TP304/304L SMLS BE 25.40MM
100 ID) (109)
200 - 200 A312-TP304/304L SMLS BE 25.40MM
100 ID) (109)
10D HIGH ALUMINA
15 - 150 A312-TP304/304L SMLS BE XXS (90% ALUMINA OXIDE)
CERAMIC-LINING (109)
10D HIGH ALUMINA
(90% ALUMINA OXIDE)
200 - 200 A312-TP304/304L SMLS BE 25.40MM CERAMIC-LINING OF 100 ID
(109)
10D HIGH ALUMINA
(90% ALUMINA OXIDE)
250 - 250 A312-TP304/304L SMLS BE 31.75MM CERAMIC-LINING OF 150 ID
(109)
10D HIGH ALUMINA
300 - 300 A312-TP304/304L SMLS BE 38.10MM (90% ALUMINA OXIDE)
CERAMIC-LINING (109)
3D HIGH ALUMINA (90%

200 - 200 A312-TP304/304L SMLS BE 25.40MM ALUMINA OXIDE) CERAMIC-
LINING OF 100 ID (109)
6D HIGH ALUMINA (90%

200 - 200 A312-TP304/304L SMLS BE 25.40MM ALUMINA OXIDE) CERAMIC-
NIPPLE (02)
15 - 40 A312-TP304/304L SMLS BBE To match pipe thickness L=3" (02,114)
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 6000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
2 328/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15M2
RATING ASME 1500#
- LICENSOR A P PWHT / NACE Not required
- LICENSOR B
WELDOLET (02,81)
FLANGE (02)
15 - 300 A182-F304/304L 1500# WN RTJ
50 - 300 A182-F304/304L 1500# WN RTJ WITH J.B
15 - 200 A182-F304/304L 1500# WN RF (82)
HIGH ALUMINA (90%
200 - 200 A182-F304/304L 1500# WN RTJ ALUMINA OXIDE) CERAMIC-
(BASALT LINING OF 100
200 - 200 A182-F304/304L 1500# WN RTJ
ID)
150 - 150 A182-F304/304L 1500# WN RF
200 - 200 A182-F304/304L 1500# WN RTJ
BLIND FLANGE
15 - 300 A182-F304/304L 1500# BLIND RTJ
GASKET
15 - 300 SS304/304L 1500# RTJ OVAL RING
15 - 200 SW(304+GRAP)IO:304 1500# RF 4.5MM (82)
BOLT/NUT
GATE
20 - 25 A182-F316L/316+HF 1500# RTJ BB OS&Y (GA-242) (08,09)
BALL
20 - 80 A351-CF8M/WC-INCONEL+HF 1500# RTJ FULL BORE F.S (BA-284) (08,09)
100 - 250 A351-CF8M/WC-INCONEL+HF 1500# RTJ FULL BORE F.S GEAR (BA-287) (08,09)
20 - 80 A351-CF8M/WC-INCONEL+HF 1500# RTJ FULL F.S EXT.BONNET (BA-284E) (08,09)
Note :
08
09
2 329/334
CLASS: 15M2
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 330/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15N1
RATING ASME 1500#
- LICENSOR B
PIPE
15 - 300 A312-TP304/304L SMLS BE SCH160 (01)
NIPPLE (02)
15 - 40 A312-TP304/304L SMLS BBE To match pipe thickness L=3" (114)
SWAGE
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 300 A182-F304/304L 1500# WN RTJ
50 - 300 A182-F304/304L 1500# WN RTJ WITH J.B
15 - 300 A182-F304/304L 1500# WN RF (82)
15 - 300 A182-F304/304L 2500# WN RTJ (82)
15 - 300 A182-F304/304L 2500# WN RF (82)
BLIND FLANGE
15 - 300 A182-F304/304L 1500# BLIND RTJ
GASKET
15 - 300 SS304/304L 1500# RTJ OVAL RING
15 - 300 SW(304+GRAP)IO:304 1500# RF 4.5MM (82)
15 - 300 SS304/304L 2500# RTJ OVAL RING (82)
15 - 300 SW(304+GRAP)IO:304 2500# RF 4.5MM (82)
BOLT/NUT
GATE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GA-243) (08,08-2,09)
50 - 150 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GA-244) (08,08-2,09)
200 - 300 A351-CF8M/316+HF 1500# RTJ BB OS&Y GEAR (GA-245) (08,08-2,09)
GLOBE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GL-211) (08,08-2,09)
50 - 100 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GL-230) (08,08-2,09)
150 - 150 A351-CF8M/316+HF 1500# RTJ BB OS&Y GEAR (GL-314) (08,08-2,09)
CHECK
50 - 300 A351-CF8M/316+HF 1500# RTJ LUG DUAL PLATE (CH-220) (07,08,08-2,09)
BALL
25 - 80 A351-CF8M/316+RTFE 1500# RTJ FULL BORE F.S (BA-285) (08-2,09)
25 - 80 A351-CF8M/316+RTFE 1500# RTJ FULL F.S EXT.BONNET (BA-285E) (08-2,09)
2 331/334
EP242-11001
(ATTACHMENT #1)
PIPING MATERIAL CLASS 15N1
RATING ASME 1500#
- LICENSOR B
Note :
08
09
2 332/334
CLASS: 15N1
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250 300
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee
2 333/334
EP242-11001
(ATTACHMENT #1)
RATING ASME 1500#
- LICENSOR B
PIPE (01,99,103)
15 - 40 A312-TP304/304L SMLS BE SCH80S
50 - 250 A312-TP304/304L SMLS BE SCH160
NIPPLE
SWAGE (02)
THREDOLET (163)
15 - 40 A182-F304/304L THRD 3000#
PLUGS (163)
15 - 40 A182-F304/304L THRD HEX
WELDOLET (02,81)
FLANGE (02)
15 - 250 A182-F304/304L 1500# WN RTJ
50 - 250 A182-F304/304L 1500# WN RTJ WITH J.B
BLIND FLANGE
15 - 250 A182-F304/304L 1500# BLIND RTJ
GASKET
15 - 250 SS304/304L 1500# RTJ OVAL RING
BOLT/NUT
GATE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GA-243)
50 - 150 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GA-244)
GLOBE
15 - 40 A182-F316/316+HF 1500# RTJ BB OS&Y (GL-211)
50 - 100 A351-CF8M/316+HF 1500# RTJ BB OS&Y (GL-230)
150 - 150 A351-CF8M/316+HF 1500# RTJ BB OS&Y GEAR (GL-314)
CHECK
REFERENCE
50 - 150 A351-CF8M/316+HF 1500# RTJ BC BALL (62)
(CH-220)
50 - 150 A351-CF8M/316+HF 1500# RTJ LUG DUAL PLATE (CH-220) (07,26,63)
BALL
100 - 150 A351-CF8M/316+RTFE 1500# RTJ FULL BORE F.S GEAR (BA-286) (09)
Note :
09
2 334/334
CLASS: 15SS
Branch Size (DN)

15 20 25 40 50 80 100 150 200 250
15 B
20 B B
25 B B B
Header Size (DN)
40 B B B B
50 W B B B B
80 W W W B B B
100 W W W W B B B
150 W W W W W B B B
Abbreviation
B Buttwelding Tee

Ra 1 020 Ep242 11001 Piping Material Specification 1

Uploaded by

Copyright:

Available Formats

Ra 1 020 Ep242 11001 Piping Material Specification 1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ra 1 020 Ep242 11001 Piping Material Specification 1

Uploaded by

Copyright:

Available Formats

p0SCO TECHNICAL SPECIFICATION D

Technical Specification for

PROJECT NAME POSCO SNG PROJECT

3.0 PIPING DESIGN 3

4.0 PLANT DESIGN 5

ATTACHMENT #1: (Piping Line Classes and Summary)

2.1 Codes and Standards

ASME B31.1 Power piping.

ASME B31.3 Process piping.

ASME B16.5 Pipe flanges and flanged fittings.

ASME B16.9 Factory-made wrought buttwelding fittings.

ASME B16.10 Face-to-face and end-to-end dimensions of valves.

ASME B16.11 Forged fittings, socket-welding and threaded.

ASME B16.34 Valves - flanged, threaded, and welded End.

ASME B36.10M Welded and seamless wrought steel pipe.

ASME B36.19M Stainless Steel Pipe.

API 607 Fire test for soft-seated quarter turn valves.

CGA G-4.4 Oxygen Pipeline Systems (EIGA Doc 13/02)

NACE MR0175 Materials resistant to sulfide stress cracking in corrosive petroleum

RA-1-020-EP241-11004 Piping Job Instruction.

2.3 Feed Documents

RA-1-020-EP400-10001 Piping Line Classes and summary.

RA-1-020-EP400-10014 Piping Line Classes addendum.

RA-1-020-EP242-10002 Piping Specification.

3.0 PIPING DESIGN

3.1 Engineering Design

The following pipe sizes shall be used:

Sizes less that DN50 shall not be used in pipe tracks.

Sizes less that DN40 shall not be used on pipe racks.

Size DN125 will only be used if specifically specified by Licensors.

The range of pipe sizes above DN600 shall be restricted to DN1600.

Steaming-out pressures and temperatures

Pump shut-off pressure

Vacuum caused by cooling and possible condensing of trapped medium

Steam/nitrogen purge pressure

If a system operating above 0 °C is connected to a system operating at 0 °C or below, the first

Piping subject to sub-atmospheric pressure shall be designed for full vacuum.

3.2 Pipe Thickness Calculation

3.3 Structural Calculation

Table 1 - Minimum structural pipe wall thickness (Ts)

Nominal pipe size Welded pipe including Threaded pipe

DN15 to 40 2.25mm 3.0mm

DN50 to 80 2.25mm 3.0mm

DN100 to 300 2.54mm -

DN350 to 450 3.0mm -

DN500 to 1600 D/150 (1) -

Note (1): “D” is the pipe outside diameter.

3.4 Branch Calculation

4.0 PLANT DESIGN

4.2 Piping above Ground Level

Piping generally shall be routed above ground level.

Pipe routings and crossings shall be on different, predetermined elevations.

Where possible, complicated crossings should be avoided by good piperack design.

4.3 Clearance and Accessibility

See Document No.RA-1-020-EP241-11004 ‘Piping Job Instruction’.

4.4 Buried Piping

Buried piping shall be considered for:

Co-ordination of underground services shall ensure sufficient separation from electrical or

4.5 Pipe Tracks and Pipe Trenches