Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 117 views

    LDM DN - 0551

    Uploaded by

    tinduong
    LDM Series lamp driver modules provide annunciation and control for Notifier's intelligent fire alarm control panels. Modules use a serial communications interface, and may be located up to 6,000 feet from the panel. Communications between the LDM Series annunciators and the host control panel are made through a two-wire EIA-485 multi-drop loop.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd

    LDM DN - 0551

    Uploaded by

    tinduong
    117 views2 pages
    LDM Series lamp driver modules provide annunciation and control for Notifier's intelligent fire alarm control panels. Modules use a serial communications interface, and may be located up to 6,000 feet from the panel. Communications between the LDM Series annunciators and the host control panel are made through a two-wire EIA-485 multi-drop loop.

    Original Title

    LDM Dn_0551

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    LDM Series lamp driver modules provide annunciation and control for Notifier's intelligent fire alarm control panels. Modules use a serial communications interface, and may be located up to 6,000 feet from the panel. Communications between the LDM Series annunciators and the host control panel are made through a two-wire EIA-485 multi-drop loop.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    117 views2 pages

    LDM DN - 0551

    Uploaded by

    tinduong
    LDM Series lamp driver modules provide annunciation and control for Notifier's intelligent fire alarm control panels. Modules use a serial communications interface, and may be located up to 6,000 feet from the panel. Communications between the LDM Series annunciators and the host control panel are made through a two-wire EIA-485 multi-drop loop.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    DN-0551:A1 • D-110

    LDM
    Lamp Driver Modules

    Annunciator Control Systems

    General
    The LDM Series lamp driver modules, when combined with a
    custom graphic display, provide annunciation and control for
    Notifier’s intelligent fire alarm control panels. These modules
    use a serial communications interface, and may be located up
    to 6,000 feet from the panel.

    Features
    • ALARM/CIRCUIT ON and TROUBLE lamp/LED per-point
    option, or more dense alarm-only option (field selectable).

    0551LDM.wmf
    • Control switch option for remote control per point.
    • Lamps/LEDs may be programmed to display status of indi-
    cating circuits or control relays as well as system status
    conditions.
    • System trouble lamp/LED signal.
    • On-line/power LED indicator.
    • Alarm and trouble resound with flash of new conditions.
    • Local sounder for both alarm/circuit-on and trouble condi-
    tions with silence/acknowledge switch connection.
    • Serial EIA-485 interface for reduced installation costs.
    • May be powered by 24 VDC from the panel or by remote
    power supplies. LDM-32
    • Efficient switch-power converter reduces power consump-
    tion.
    • Microprocessor-controlled electronics, fully supervised. Installation
    • Plug-in terminal blocks for ease of installation and service. The LDM-32 and LDM-E32 modules mount on four standoffs
    • Trouble monitor option for remote power supplies. inside the custom annunciator graphic box. Alternately, the
    modules may be installed in a CHS-4L chassis. The module
    size is approximately 4.4” (11.2cm) x 7.1” (18cm).
    Construction
    Communications between the LDM Series annunciators and
    Two basic models are available; the LDM-32 control module the host FIre Alarm Control Panel are made through a
    and the LDM-E32 expander module. Each may be selected to two-wire EIA-485 multi-drop loop, and a two-wire regulated 24
    provide 32 alarm indications; or 16 alarm, 16 trouble, and 16 VDC power loop. Up to 32 LDM systems may be connected to
    control points. a single control panel.
    All field-wiring terminations use removable, compression-type
    Applications terminal blocks for ease of installation, wiring, and circuit test-
    The LDM-32/LDM-E32 with a custom graphic array may be ing.
    used to indicate point status and, in some versions, to control
    the state of output points. Operation
    In addition, the LDM-R32 module may be used to provide 32 LDM Series modules, when used with a custom graphic
    dry-contact relays for electrical isolation when connecting the annunciator, provide the Notifier’sintelligent fire alarmcontrol
    system to other equipment. panels with up to 32 unique or redundant annunciators, each
    with a capacity of 64 points for a total capacity of 2048 points.
    Local or remote power supplies and serial communications
    allow the custom annunciators to be located anywhere on the
    protected premises.
    AM2020/AFP1010 system alarm and/or trouble conditions
    may be annunciated on a per-point basis, or in a grouped-zone
    configuration.
    AFP300/400 system panel points, intelligent addressable
    devices and software zones can be annunciated/controlled in
    a grouped fashion (see programming manual for details).
    Control of system operational controls, such as Signal Silence,
    System Reset, and local annunciation controls (such as Local

    DN-0551:A1 • 08/20/09 — Page 1 of 2


    Acknowledge), and Lamp Test may be accomplished through sounder sounds for each new alarm or trouble and is silenced
    special key- or push-switches. with the Local Acknowledge switch, or permanently disabled
    with a dip switch selection. Flash of new alarms or troubles is
    Agency Listings and Approvals selectable through dip switches. 16 switch inputs may be used
    for panel SILENCE, RESET, or remote relay control. Instruc-
    These listings and approvals apply to the modules specified in tions are included.
    this document. In some cases, certain modules or applications
    may not be listed by certain approval agencies, or listing may LDM-E32: Lamp Driver Module with 32 alarm drivers; or 16
    be in process. Consult factory for latest listing status. alarm, 16 trouble, and 16 switch inputs. One LDM-E32 is
    allowed per LDM-32 in alarm-only mode. Three LDM-E32
    • UL Listed: S632 modules are allowed per LDM-32 in alarm/trouble. Includes
    • ULC Listed: CS100 ribbon cable to connect to ACM.
    • MEA Listed: 291-61-E Vol. IV (System 500, LDM-R32); LDM-R32: Lamp Driver Module which connects to any LDM-
    289-91-E Vol. V (AM2020/AFP1010); 104-93-E (AFP-200); 32 or LDM-E32 to convert transistor outputs to 32 Form-A dry
    17-96-E (AFP-300/400); 447-99-E (AFC-600) contacts (1.0 A @ 30 VDC). Provides 32 output terminal
    • CSFM: 7120-0028:156, 7165-0028:224 (NFS-3030, NFS2- screw connections and a single common terminal screw.
    3030); 7170-0028:216 (NFS-640); 7170-0028:223 (NFS- Includes ribbon cables to connected to the LDM-32/LDM-E32.
    3030, NFS2-3030) Use for electrical isolation when interfacing the system to other
    • BSA: 578-81-SA (System 5000, System 500 except equipment.
    LDM-R32) LDM-CBL24, LDM-CBL48: Ribbon cable sets to provide
    • FM Approved either a 24” (60.96cm) or 48” (121.96cm) connection between
    LDM-32/LDM-E32 and LEDs or lamps on a custom graphic
    • City of Chicago approved: Class 1, Class 2
    panel. Includes all cables necessary for one LDM-32 or
    • City of Denver approved LDM-E32. Cables have connector on one end only (split, strip,
    and connect other end to graphic annunciator).
    Product Line Information
    LDM-32: Lamp Driver Module with 32 alarm lamp-driver tran- Architectural/Engineering
    sistors (sink to power common on alarm). May be selected Specifications
    (dip switch) for 16 alarm/circuit on, 16 trouble, and 16 switch
    For specifications on LDM Graphic Annunciator Lamp Driver
    inputs if desired. Also includes system-trouble lamp driver and
    Modules, contact NOTIFIER.
    lamp-test/local-acknowledge switch input. Integral piezo
    0551cbl.wmf

    0551RLDM.wmf
    0551ELDM.wmf

    LDM-CLS24,
    LDM-E32 LDC-CBL48 LDM-R32

    NOTIFIER® is a registered trademarks of Honeywell International Inc.


    ©2006 by Honeywell International Inc. All rights reserved. Unauthorized use
    of this document is strictly prohibited.

    This document is not intended to be used for installation purposes.


    We try to keep our product information up-to-date and accurate.
    We cannot cover all specific applications or anticipate all requirements.
    All specifications are subject to change without notice.
    Made in the U.S. A.
    For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
    www.notifier.com

    Page 2 of 2 — DN-0551:A1 • 08/20/09

    You might also like