A Project On "Quality Improvement Through Rework Reduction"

A project
On
“Quality Improvement through Rework Reduction”
Abstract
As the global economic condition changing in a rapid motion, generally in an industry more
focus is given on profit margin, customer demand for high quality product and improved
productivity. In this project cutting, sewing and finishing sections is to identify reworks so as to
eliminate them for cutting, saving time, cost and improved product quality. In the Apparel
Manufacturing Industry, main raw material is fabric; others are different types of trimming and
accessories. Operational wastages in the Apparel manufacturing process are top surface Rework,
printed label rework, knitting fault, dying fault (shade and shrinkage- major problem in JPC
PVT LTD NOIDA), cutting fault, sewing fault rework, pinhole rework, fabric rework, and other
reworks
Key Words: DHU %, fabric defects, Garment defects, Costs, Operation, Productivity,
Profitability, product Quality, Reworks.
Introduction
In garment manufacturing, it is usual few rejected garments after shipment. Reason, most of the
manufacturers believe that garments are soft goods and non-repairable defect may occur due to
low quality raw materials or faulty process or employee casual behavior. However, factory must
have check points to control over this issue. There is no ready-made solution that can reduce
rejection percentage overnight. Each order is unique. But this project works suggest how to
handle this issue and bring down rejection rate to minimum. As see a lot of rejected garment
after shipment. Most of the organization termed these garments as rejected because those
garments can’t be by any means. Reworks in the garments industry is a common works that
hampers the smooth production rate and focus poor quality products having an impact on overall
factory economy.
Literature Review
In the modern area of the textile technology we are well aware about the minimization of the
defect in the garment industry. The basic needs for productivity increase in the sewing
department. We have to control the productivity by keeping the intension on the minimization of
the defect in the sewing department through the actual taking the supervising& strict operating
condition to be followed. Type of Faults Affecting the DHU% -
 Shade problems
 Shrinkage and GSM problems
 Cutting Problems
 Wrong stitching
 Turnout stitch Hole
 Machine cut
 Thick place
 Spots or stain
 Oil stain
 Color stain
 Dirt stain
 Printing problems
1. Quality Check Points in Departments:
D.H.U. – IT stands for Defect per Hundred Units. It means number of defects found or detected
per 100 garments. This is also known as DHU (Defects per Hundred Units). 1. Defects per
Hundred Units and 2. Percent Defectives:
DHU % = (Total no. of defects /Total no of pieces) 𝑋100
Percent Defectives = (Defective Pieces/ Total pieces) 𝑋100
1.1 Measure D.H.U:

To measure DHU of any process, one needs to record number of total pieces checked and
number of total defects are detected in the inspected garments. It is number of defects not the
defective garments. One defective garment may have more than one defect. Like a checker
found broken stitch, a whole and raw edges in shirt. Here checker found one defective shirt
but the defective shirt contains 3 defects. Once you have record of the following information
of a lot you can measure DHU of that lot using above formula.
1.2 Acceptable Quality level:
Lot or Batch size this means total how many pieces inspector is going to check or inspect. (If
you have been offered a shipment of 600 pieces order quantity, the batch size of this
shipment will fall under 501 to 1200 pieces (Code-J) Sample size Code letter This code is
indicative a range of batch size. (Code 'G' means your lot size range is from 151 pieces to
280 pieces. Sample size it means that how many pieces will be picked up for inspection from
the total offered pieces (Batch). Ac (Accepted): The number in this column denotes that if the
inspector finds up to that many defective pieces the shipment will be accepted by buyer. Re
(Rejected): On the other hand number in this column denotes that if the inspector finds that
much defective pieces or more than the listed number, the shipment will be rejected (or asked
to the manufacturer for 100% inspection and re-offer for final inspection) by buyer.
1.3 Fabric Quality Check:
Fabric is checked 100 % or randomly for various defects like -weaving defect holes,
printing/dyeing defects, water crease marks, color variations etc. Factories generally follow
4-point system for fabric inspection for woven as well as knits fabrics.
1.4 Trim Quality check:
All trims are checked for durability & performance. All trims are attached correctly using
proper attachment methods. Ribbons ends are heat sealed. Trim materials are checked to
perform consistently with the base fabric performance with no differential shrinkage.
1.5 Cutting quality checks:
Shade variation in cut bundles is being controlled. Other important quality aspects that are
taken care are like – using of pattern according to fabric shrinkage, controlling fabric skew or
torque, all plaids, horizontal/vertical stripes are given extra care so as to match the stripes.
Light weight fabrics are relaxed to avoid measurement error while stitching.
1.6 Stitching quality checks:
Quality is checked whether garment construction meets with the buyer requirement like
garment measurement, stitching quality, seam quality, trims and label are attached correctly.
1.7 Finishing & Washing:

All the garments are given sufficient time to relax and dry thoroughly prior to packing to
avoid foul smelled. Thread cutting, ironing, spotting and other finishing processes are done
under strict quality control measures. 100% garments are checked for - Correct labeling,
hangtag positioning and carton marking, Correct ratio packing, quantity check in each carton
as per the packing instruction. All the packed garments are inspected 2.5AQL quality audit
before forwarding goods to the buyer's Q.A. team.

A Project On "Quality Improvement Through Rework Reduction"

Uploaded by

Copyright:

Available Formats

A Project On "Quality Improvement Through Rework Reduction"

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

A Project On "Quality Improvement Through Rework Reduction"

Uploaded by

Copyright:

Available Formats

A project

“Quality Improvement through Rework Reduction”

1. Quality Check Points in Departments:

DHU % = (Total no. of defects /Total no of pieces) 𝑋100

Percent Defectives = (Defective Pieces/ Total pieces) 𝑋100

1.1 Measure D.H.U:

1.4 Trim Quality check:

1.5 Cutting quality checks:

1.6 Stitching quality checks:

1.7 Finishing & Washing:

You might also like