Remote Control Unit (RCU)

Remote Control Unit (RCU) for Kathrein base station antennas with adjustable electrical down-tilt
and appropriate mechanical interface.

• Compliant to AISG 1.1 and 3GPP/AISG 2.0 • Daisy Chain feasibility

• Compact size • Suitable for operation under outdoor conditions
• Prepared for automatic configuration and calibration

Type No. 86010148V01

Protocols compliant to AISG 1.1 and 3GPP/AISG 2.0
Logical interface ex factory 1) 3GPP/AISG 2.0
Input voltage range V 10 ... 30 (pin 1, pin 6)
Power consumption W < 1 (stand by); < 10 (motor activated)
Connectors 2) 3) 2 x 8 pin connector according to IEC 60130-9; according to AISG
Daisy chain in: male; Daisy chain out: female
Hardware interfaces RS 485A/B (pin 5, pin 3);
power supply (pin 1, pin 6); DC return (pin 7);
according to AISG / 3GPP
Adjustment time (full range) sec 40 (typically, depending on antenna type)
Adjustment cycles > 50,000
Temperature range °C –40 … +60
Protection class IP 24
Lightning protection AISG interface (each pin)
2.5 kA (10/350 μs)
8 kA (8/20 μs)
Housing material Profile: Aluminum anodized; cover: Aluminum die cast coated
Weight kg 0.5
Ibs 0.99
Packing size mm 245 x 93 x 102
inches 9.6 x 3.6 x 4
Dimensions (H x W x D) mm 177.5 x 59.5 x 49.5
inches 7.0 x 2.3 x 1.9
1)
The protocol of the logical interface can be switched from 3GPP/AISG 2.0 AISG 1.1 to with a vendor
specific command. Start-up operation of the RCU is only possible in a RET system supporting 3GPP/
AISG 2.0!
The protocol can also be changed as follows: 3GPP to AISG 1.1: Enter “AISG1” into the additional data
field “Installer’s ID” and perform a layer 2 reset or a power reset. AISG 1.1 to 3 GPP: Enter “3GPP” into
the additional data filed “Installer’s ID” and perform a layer 7 reset or a power reset. After switching the
protocol any other information can be entered into the “Installer’s ID” field.
Daisy chain in Daisy chain out
Please note: (male) (female)
If the Primary of the RET system doesn’t support the standard of the ‘logical interface ex factory’, the RCU
must be switched to the appropriate standard of the Primary before installation. Please contact Kathrein for
further information.
2)
The tightening torque for fixing the connector must be 0.5 – 1.0 Nm. The connector should be tightened
by hand or using the torque screwdriver (85010080) as described in the connecting cable data sheet
(85010007, ...)
3)
The RCU gets the information stored in the antenna after power on automatically if a corresponding
antenna is used. In this case, it is not necessary to configurate the RCU manually.
Standards: EN 60950-1 (Safety) Bottom view of RCU
EN 60950-22 (Safety – Equipment installed outdoor)
EN 55022 (Emission)
EN 55024 (Immunity)
ETS 300019-1-4 (Environmental)
Subject to alteration.

UL 60950-1; 1st edition

Certification: CE, FCC
Scope of supply: Remote Control Unit
Assembly paste

173.6 | 6.8 49.5 | 1.95

936.4624/e

59.5 | 2.34
’ 46 | 1.8
M42x1.5

28.5 | 1.1

8 | 0.31
33.2 | 1.27
All dimensions in mm | inches

All specifications are subject to change without notice. 86010148V01 Page 1 of 5

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Remote Control Unit (RCU)

Please note: In general, the addressing of the RCU is automatically performed. Only in case the RCU is manually addressed,
the serial number written on the product label has to be extended by the corresponding colour coding extension
(e.g. CSG351234-R1). If the connected antenna has no RFID spindles, the serial number has to be extended by
“-XX“ instead of the colour coding extension (e.g. CSG351234-XX)

Please note: Additional grounding of the RCU is not required if the RCU is fixed to an antenna with proper ground-
ing. Please assure that grounding of the antenna has been carried out according to all relevant local
regulations.

Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are
obliged to point out certain risks that may arise when products are used under extraordinary operating
conditions.

The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4 and thereby
respects the static mechanical load imposed on an antenna by wind at maximum velocity. Wind loads are
calculated according to DIN 1055-4. Extraordinary operating conditions, such as heavy icing or exceptional
dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or
even cause it to fall to the ground. These facts must be considered during the site planning process.

The installation team must be properly qualified and also be familiar with the relevant national safety
regulations.
The details given in our data sheets have to be followed carefully when installing the antennas and
accessories.
The limits for the coupling torque of RF-connectors, recommended by the connector manufacturers
must be obeyed.

Any previous datasheet issues have now become invalid.

Description of the adjustment mechanism (protective cap removed):

1
2

2
j Adjustment wheel with twist- j Thread for fixing the protective To set the downtilt angle exactly,
you must look horizontally at the
Subject to alteration.

lock function. cap or the RCU (Remote Control

Unit). scale. The lower edge of the gear-
k Downtilt spindle with integrated wheel must be used for alignment.
scale. k Gearwheel for RCU power drive.
936.4624/e

All specifications are subject to change without notice.

Page 2 of 5 86010148V01
The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 Instructions for RCU Installation

Attaching the RCU (Remote Control Unit) for remote-controlled downtilt adjustment:

Clean the thread surface.

Apply the assembly-paste evenly
onto the full circumference of the
thread as illustrated in the figure.
Note!
Twist off the protective cap com- Avoid ingestion and contact Push the attachment nut of the Tighten the RCU attachment nut
pletely from the antenna. with eyes. RCU down towards the housing. using a torque-wrench; wrench
In case of contact with eyes width = 41 mm,
Check the proper function of Place the RCU carefully over the
rinse thoroughly with plenty of min. torque = 15 Nm,
the phase shifter over the entire adjustment spindle, observing the
water. In case of irritation seek max. torque = 18 Nm.
adjustment range by twisting correct alignment of the RCU with
medical advice.
the adjustment wheel in such regards to the antenna, i.e. the Connect the RCU control cable
Avoid long-term contact with
a way, that the spindle moves flat surfaces of the attachment immediately after attachment of
skin.
completely in and out. fixture on the antenna side and the RCU. The tightening torque
In case of contact with skin
those inside the RCU housing for fixing the control cable con-
Reset the downtilt to min. degree. wash off with soap and water.
must lie flat against each other. nector must be 0.5 – 1.0 Nm
Completely remove the black For further information (‘hand-tightened’) or using the
Push-up the RCU carefully to the
adjustment wheel by simply please read the safety data-sheet torque swrewdriver (85010080) as
stop at the antenna.
pulling it downwards. ‘Klüberplex AG 11-461’ described.
by company Please note!
Please note!
Klüber Lubrication München KG Do not twist the RCU during
In cases where a mechanical
Geisenhausenerstraße 7 attaching to the antenna, as
downtilt unit is installed, this
D-81379 München this may damage the adjust-
must not be set for a downtilt of
http://www.klueber.com ment spindle.
more than 14 degrees.

If an antenna with RFID-Tag is used:

– Adjust the tilt (spindle on the antenna) to min. degree

– Connect the RCU onto the antenna
– Connect an AISG-Control-Cable on the input (daisy chain in) of the
RCU
– After power is switched on, the RCU reads out all information (such
Subject to alteration.

as antenna type, serical number, tilt range, ...) automatically

– Perform an ALD-Scan (Antenna Line Device)
– Fill in all site specific information (such as sector-ID, install-ID, ...) in
the detail view of the RCU
– After the first set-tilt-command, the RCU will calibrate the system
automatically – no seperate calibration command is neccessary!
936.4624/d

For daisy chain operation, remove the protection cap

and attach a control cable to interconnect with the
daisy chain input of the subsequent RCU.
Please note: Do not remove the protection cap
on the daisy chain output of the last RCU device.

All specifications are subject to change without notice. 86010148V01 Page 3 of 5

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
FCC – Statements

FCC – Statements

FCC § 15.19

This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

FCC § 15.105

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.

Canada CNR-Gen Section 7.1.3

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to
the following two conditions:(1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Subject to alteration.

ICES-003

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

936.4624/d

FCC § 15.21 (Warning Statement)

[Any] changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.

Page 4 of 5 86010148V01 All specifications are subject to change without notice.

The latest specifications are available at www.kathreinusa.com
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
 FCC – Statements

Compliance Information Statement

(Declaration of Conformity Procedure)
Responsible Party: Kathrein h^

Address: 'ƌĞĞŶǁĂLJWůĂnjĂ//͕ϮϰϬϬ>ĂŬĞƐŝĚĞůǀĚ͘^ƵŝƚĞϲϱϬ͕ϳϱϬϴϮZŝĐŚĂƌĚƐŽŶ͕dĞdžĂƐ

Telephone: (+01)ϮϭϰϮϯϴϴϴϬϬ

Type of Equipment:

Model Name: Remote Control Unit (RCU)

FCC ID SP3-86010148V01
Subject to alteration.
936.4624/d

Any previous data sheet issues have now become invalid.

All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com
86010148V01 Page 5 of 5

Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com