Agarose Gels IMBB 2013
Agarose Gels IMBB 2013
Agarose Gels IMBB 2013
gel
electrophoresis
of
DNA
IMBB 2013
Acknowledgement
The content of this presentation has been adapted from:
DNAà
- +
Power
small
large
-‐
+
Power
Within
an
agarose
gel,
rate
of
migra8on
of
a
linear
DNA
molecule
is
inversely
propor8onal
to
the
log10
of
the
molecular
weight.
Movies
Making
an
Agarose
Gel
-‐
University
of
Leicester.flv
Running
an
Agarose
Gel
-‐
University
of
Leicester.flv
Agarose
is
a
linear
polymer
extracted
from
seaweed
Agarose
D-galactose 3,6-anhydro
L-galactose
Electrophoresis
equipment
Power supplyà
åTank cover
Electrical leads
â
Gel tank
Casting trayä
Gel combsä
Making
an
agarose
Gel
Agarose
Gel casting tray & combs
Preparing the casting tray
§ Seal
the
edges
of
the
cas8ng
tray
and
put
in
the
combs.
§ Place
the
cas8ng
tray
on
a
level
surface.
§ None
of
the
gel
combs
should
touch
the
surface
of
the
cas8ng
tray.
Agarose
Buffer
Solu8on
§ Combine
the
agarose
powder
and
buffer
solu8on
(1-‐2%
agarose).
§ Use
a
flask
that
is
several
8mes
larger
than
the
volume
of
buffer.
§ Swirl
gently
to
give
a
uniform
suspension
(no
lumps!).
Mel8ng
the
agarose
• The
easiest
way
to
boil
the
mixture
is
with
a
microwave
oven.
• Gently
swirl
the
solu8on
periodically
when
hea8ng
to
allow
all
the
grains
of
agarose
to
dissolve.
• Be
careful
when
boiling
-‐
the
agarose
solu8on
may
become
superheated
and
may
boil
violently
if
it
has
been
heated
too
long
in
a
microwave
oven.
Pouring the gel
§ Allow
the
agarose
solu8on
to
cool
by
placing
the
flask
in
a
water
bath
set
at
55oC.
§ Add
GelRed
DNA
dye,
and
mix
by
swirling.
§ Then
carefully
pour
the
melted
agarose
solu8on
into
the
cas8ng
tray.
§ Avoid
air
bubbles.
§ Each
of
the
gel
combs
should
be
submerged
in
the
melted
agarose
solu8on.
§ Remove
air
bubbles
with
a
pin
or
pipebe
8p.
§ When
cooled,
the
agarose
polymerizes,
forming
a
flexible
gel.
It
should
appear
lighter
in
color
when
completely
cooled
(30-‐45
minutes).
§ Carefully
remove
the
combs
and
tape.
§ The
gel
can
be
used
immediately
or
stored
(wrapped
in
cling
film)
in
a
fridge
for
a
few
days
before
use.
Place the gel in the electrophoresis chamber.
Direction of DNA migration è
buffer è á á á á
wells
Anode ä
ã Cathode (positive)
(negative)
• Add enough electrophoresis buffer to cover the gel to a depth of at least ~2 mm.
• Make sure each well is filled with buffer.
Sample
Prepara8on
• Mix
the
samples
of
DNA
with
2X
sample
loading
buffer
containing
a
dye.
(Mix
1
part
loading
buffer
with
1
parts
DNA
sample).
• Approximately
5-‐10
microlitres
(μL)
of
sample
are
loaded
into
a
well,
depending
on
the
size
of
the
well.
• The
dye
in
the
loading
buffer
allows
the
samples
to
be
seen
when
loading
onto
the
gel.
Glycerol
in
the
loading
buffer
increases
the
density
of
the
samples,
causing
them
to
sink
into
the
wells.
• The
loading
buffer
dye,
which
migrates
during
electrophoresis,
also
helps
to
monitor
the
progress
of
the
separa8on.
Loading the Gel
§ Carefully place the pipette tip over a well and gently expel the sample.
§ The sample should sink into the well.
§ Be careful not to puncture the gel with the pipette tip.
Running the Gel
§ Place
the
cover
on
the
electrophoresis
chamber,
connec8ng
the
electrical
leads.
§ Connect
the
electrical
leads
to
the
power
supply.
§ Be
sure
the
leads
are
abached
correctly
-‐
DNA
migrates
toward
the
anode
(red).
§ When
the
power
is
turned
on,
bubbles
should
form
on
the
electrodes
in
the
electrophoresis
chamber.
Including
a
DNA
ladder
enables
the
es8ma8on
of
sample
DNA
size
Staining the DNA
Ethidium bromide has been the most commonly used DNA stain for many
years.
*CAUTION!