Omni DT

LEVELTOOLS
TEST | Cased |Hole

1 CAPABILITY Level 2 Capability (if applicable)
OMNI™ DT Circulating Valve

MULTI-CYCLE ISOLATION AND CIRCULATION VALVE
HAL10651
OVERVIEW
The OMNI™ DT circulating valve is a next-generation annulus pressure-operated,
recloseable circulating valve.
The OMNI DT circulation has been designed and tested to be more “debris
tolerant” than previous re-closeable circulating valves. The OMNI DT valve consists
of a nitrogen section, an oil system, a circulating valve, and a ball valve. Throughout
the operation, the tool is repeatedly cycled up to a predetermined annulus
pressure and then released. The nitrogen section contains the nitrogen gas that
counterbalances the hydrostatic and annulus pressures. The amount of nitrogen
in the tool depends on well hydrostatic (mud weight and depth) and downhole
temperature. This information must be known to prepare the tool properly to be run.
For certain completion fluids, the fluid density at the surface can be significantly
different from the actual density downhole.
The operating and control mechanisms are contained in a closed oil system
activated by annulus pressure acting on the nitrogen chamber, enabling an
unlimited number of pressure cycles.
The circulating valve and the ball valve work together to keep circulating pressure off
the formation. The ball valve will close before the circulating valve opens. The ball valve
closes off the work string. The circulating ports close before the ball valve opens.
FEATURES AND BENEFITS

»» Permits well testing, pressure testing, fluid circulation, spotting acid, and cushion fluids
»» Enables unlimited number of tool operational cycles
OPERATION
The well can be flow tested when the valve is in the well-test position. When in
this position, the circulating ports are closed and the ball valve is opened. During a
downhole closure drillstem test, the OMNI valve is in the well-test position during
flow and shut-in periods. The work string can be pressure-tested in the blank
position, because the ball valve closes before the circulating valve opens. Fluid can
be pumped in either direction through the tool in the circulating position. In this
position, the circulating ports are open and the ball valve is closed. The tool does
not require any specific flow rate to operate.
Before the tool is run, the hydrostatic pressure and bottom hole temperature at
the specified tool depth must be known. This information is required to obtain the
proper nitrogen charging pressure.
LEVELTOOLS
TEST | Cased |Hole
1 CAPABILITY Level 2 Capability (if applicable)
Equipment Specifications
Nominal Tool Size (in.) 3 7/8 5 7
Outer Diameter in. (cm) 3.90 (9.91) 5.03 (12.78) 7.03 (17.86)
Inner Diameter in. (cm) 1.80 (4.57) 2.25 (5.72) 3.50 (8.89)
Makeup Length in. (cm) 278.79 (708.13) 261.31 (663.73) 333.21 (846.35)
End Connections 2 7/8 CAS 3 7/8 CAS 5 1/4 CAS
Absolute Pressure1 psi (bar) >25,000 (1724) >25,000 (1724) >25,000 (1724)
Differential Pressure2 psi (bar) 15,000 (1034) 15,000 (1034) 10,000 (689)
Tensile Load3 lb (kg) 175,000 (79,379) 371,000 (168,282) 470,000 (213,188)
Service Temperature °F (°C) 400 (204) 450 (232) 400 (204)
Circulating Flow Area in.2 (cm2) 3.61 (23.29) 3.61 (23.29) 8.91 (57.48)
Number of Ports 6 6 6
Static Differential Across Ball from Above psi (bar) 15,000 (1034) 15,000 (1034) 10,000 (689)
Opening Differential Across Ball from Above psi (bar) 5000 (345) 5000 (345) 2500 (172)
Static Differential Across Ball from Below psi (bar) 10,000 (689) 10,000 (689) 10,000 (689)
Opening Differential Across Ball from Below psi (bar) 1000 (69) 2500 (172) 1000 (69)
Static Differential Across Seal from Inside psi (bar) 15,000 (1034) 15,000 (1034) 10,000 (689)
Opening Differential Across Seal from Inside psi (bar) 0 0 0
Static Differential Across Seal from Outside psi (bar) 15,000 (1034) 15,000 (1034) 10,000 (689)
Opening Differential Across Seal from Outside psi (bar) 6000 (414) 5000 (345) 2500 (172)
Notes:
1
Absolute pressure is the total hydrostatic plus applied pressure.
2
Differential pressure is the difference in pressure between the casing annulus and the tool ID.
3
The values of tensile, burst, and collapse strength are calculated with new tool conditions, Lame formulas with von Mises’ Distortion Energy Theory for burst and collapse
strength, and stress area calculations for tensile strength.
»
»Meets NACE MR0175 requirements (>175°F / 79°C).
»
»These ratings are guidelines only. Refer to the equipment data book for individual equipment specifications.
For more information, contact your local Halliburton representative

or visit us on the web at www.halliburton.com
Sales of Halliburton products and services will be in accord solely with the terms and conditions
contained in the contract between Halliburton and the customer that is applicable to the sale.
H07826 10/16 © 2016 Halliburton. All Rights Reserved.

Omni DT

Uploaded by

Copyright:

Available Formats

Omni DT

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omni DT

Uploaded by

Copyright:

Available Formats

LEVELTOOLS

TEST | Cased |Hole

OMNI™ DT Circulating Valve

FEATURES AND BENEFITS

Nominal Tool Size (in.) 3 7/8 5 7

End Connections 2 7/8 CAS 3 7/8 CAS 5 1/4 CAS

Tensile Load3 lb (kg) 175,000 (79,379) 371,000 (168,282) 470,000 (213,188)

Service Temperature °F (°C) 400 (204) 450 (232) 400 (204)

Opening Differential Across Seal from Inside psi (bar) 0 0 0

For more information, contact your local Halliburton representative

H07826 10/16 © 2016 Halliburton. All Rights Reserved.

You might also like