2D Symbols: Reference Data Guide

2D Symbols
Reference Data Guide
Version 2016 (11.0)

November 2016
Copyright
Copyright © 2006-2016 Intergraph® Corporation. All Rights Reserved. Intergraph is part of Hexagon.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license agreement; contains
confidential and proprietary information of Intergraph and/or third parties which is protected by copyright law, trade secret law, and
international treaty, and may not be provided or otherwise made available without proper authorization from Intergraph Corporation.
Portions of this software are owned by Spatial Corp. © 1986-2016. All Rights Reserved.
Portions of the user interface are copyright © 2012-2016 Telerik AD.
U.S. Government Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies: This was
developed at private expense and is "restricted computer software" submitted with restricted rights in accordance with
subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at 52.227-19 of the Federal
Acquisition Regulations ("FAR") and its successors, and is unpublished and all rights are reserved under the copyright laws of the
United States. For units of the Department of Defense ("DoD"): This is "commercial computer software" as defined at DFARS
252.227-7014 and the rights of the Government are as specified at DFARS 227.7202-3.
Unpublished - rights reserved under the copyright laws of the United States.
Intergraph Corporation
305 Intergraph Way
Madison, AL 35758
Documentation
Documentation shall mean, whether in electronic or printed form, User's Guides, Installation Guides, Reference Guides,
Administrator's Guides, Customization Guides, Programmer's Guides, Configuration Guides and Help Guides delivered with a
particular software product.
Other Documentation
Other Documentation shall mean, whether in electronic or printed form and delivered with software or on Intergraph Smart Support,
SharePoint, or box.net, any documentation related to work processes, workflows, and best practices that is provided by Intergraph
as guidance for using a software product.
Terms of Use
a. Use of a software product and Documentation is subject to the End User License Agreement ("EULA") delivered with the
software product unless the Licensee has a valid signed license for this software product with Intergraph Corporation. If the
Licensee has a valid signed license for this software product with Intergraph Corporation, the valid signed license shall take
precedence and govern the use of this software product and Documentation. Subject to the terms contained within the
applicable license agreement, Intergraph Corporation gives Licensee permission to print a reasonable number of copies of the
Documentation as defined in the applicable license agreement and delivered with the software product for Licensee's internal,
non-commercial use. The Documentation may not be printed for resale or redistribution.
b. For use of Documentation or Other Documentation where end user does not receive a EULA or does not have a valid license
agreement with Intergraph, Intergraph grants the Licensee a non-exclusive license to use the Documentation or Other
Documentation for Licensee’s internal non-commercial use. Intergraph Corporation gives Licensee permission to print a
reasonable number of copies of Other Documentation for Licensee’s internal, non-commercial use. The Other Documentation
may not be printed for resale or redistribution. This license contained in this subsection b) may be terminated at any time and
for any reason by Intergraph Corporation by giving written notice to Licensee.
Disclaimer of Warranties
Except for any express warranties as may be stated in the EULA or separate license or separate terms and conditions, Intergraph
Corporation disclaims any and all express or implied warranties including, but not limited to the implied warranties of merchantability
and fitness for a particular purpose and nothing stated in, or implied by, this document or its contents shall be considered or deemed
a modification or amendment of such disclaimer. Intergraph believes the information in this publication is accurate as of its
publication date.
The information and the software discussed in this document are subject to change without notice and are subject to applicable
technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in this document.
2D Symbols Reference Data Guide 2

The software, Documentation and Other Documentation discussed in this document are furnished under a license and may be used
or copied only in accordance with the terms of this license. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINAL
EVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.
Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and symbol data.
Users should verify for themselves that the data is accurate and suitable for their project work.
Limitation of Damages
IN NO EVENT WILL INTERGRAPH CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL INCIDENTAL,
SPECIAL, OR PUNITIVE DAMAGES, INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR PRODUCTION, LOSS OF
REVENUE OR PROFIT, LOSS OF DATA, OR CLAIMS OF THIRD PARTIES, EVEN IF INTERGRAPH CORPORATION HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
UNDER NO CIRCUMSTANCES SHALL INTERGRAPH CORPORATION’S LIABILITY EXCEED THE AMOUNT THAT
INTERGRAPH CORPORATION HAS BEEN PAID BY LICENSEE UNDER THIS AGREEMENT AT THE TIME THE CLAIM IS
MADE. EXCEPT WHERE PROHIBITED BY APPLICABLE LAW, NO CLAIM, REGARDLESS OF FORM, ARISING OUT OF OR IN
CONNECTION WITH THE SUBJECT MATTER OF THIS DOCUMENT MAY BE BROUGHT BY LICENSEE MORE THAN TWO (2)
YEARS AFTER THE EVENT GIVING RISE TO THE CAUSE OF ACTION HAS OCCURRED.
IF UNDER THE LAW RULED APPLICABLE ANY PART OF THIS SECTION IS INVALID, THEN INTERGRAPH LIMITS ITS
LIABILITY TO THE MAXIMUM EXTENT ALLOWED BY SAID LAW.
Export Controls
Intergraph Corporation’s software products and any third-party Software Products obtained from Intergraph Corporation, its
subsidiaries, or distributors (including any Documentation, Other Documentation or technical data related to these products) are
subject to the export control laws and regulations of the United States. Diversion contrary to U.S. law is prohibited. These Software
Products, and the direct product thereof, must not be exported or re-exported, directly or indirectly (including via remote access)
under the following circumstances:
a. To Cuba, Iran, North Korea, Sudan, or Syria, or any national of these countries.
b. To any person or entity listed on any U.S. government denial list, including but not limited to, the U.S. Department of Commerce
Denied Persons, Entities, and Unverified Lists, http://www.bis.doc.gov/complianceandenforcement/liststocheck.htm, the U.S.
Department of Treasury Specially Designated Nationals List, http://www.treas.gov/offices/enforcement/ofac/, and the U.S.
Department of State Debarred List, http://www.pmddtc.state.gov/compliance/debar.html.
c. To any entity when Licensee knows, or has reason to know, the end use of the Software Product is related to the design,
development, production, or use of missiles, chemical, biological, or nuclear weapons, or other un-safeguarded or sensitive
nuclear uses.
d. To any entity when Licensee knows, or has reason to know, that an illegal reshipment will take place.
Any questions regarding export or re-export of these Software Products should be addressed to Intergraph Corporation’s Export
Compliance Department, Huntsville, Alabama 35894, USA.
Trademarks
Intergraph, the Intergraph logo, PDS, SmartPlant, FrameWorks, I-Sketch, SmartMarine, IntelliShip, ISOGEN, SmartSketch,
SPOOLGEN, SupportManager, SupportModeler, Sapphire, and Intergraph Smart are trademarks or registered trademarks of
Intergraph Corporation or its subsidiaries in the United States and other countries. Hexagon and the Hexagon logo are registered
trademarks of Hexagon AB or its subsidiaries. Microsoft and Windows are registered trademarks of Microsoft Corporation. ACIS is a
registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics, Presentation Layer Framework, ActiveTreeView Ctrl,
ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl, ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are
trademarks of Infragistics, Inc. Incorporates portions of 2D DCM, 3D DCM, and HLM by Siemens Product Lifecycle Management
Software III (GB) Ltd. All rights reserved. Gigasoft is a registered trademark, and ProEssentials a trademark of Gigasoft, Inc.
VideoSoft and VXFlexGrid are either registered trademarks or trademarks of ComponentOne LLC 1991-2013, All rights reserved.
Oracle, JD Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Tribon is a
trademark of AVEVA Group plc. Alma and act/cut are trademarks of the Alma company. Other brands and product names are
trademarks of their respective owners.

Contents
Preface .......................................................................................................................................................... 8
What's New in 2D Symbols Reference Data ............................................................................................. 8
2D Symbols Reference Data ....................................................................................................................... 9
Bracket Symbols ....................................................................................................................................... 10

2S Brackets ........................................................................................................................................... 11
3S Trimmed Brackets ........................................................................................................................... 16
3S Lapped S1 Brackets ........................................................................................................................ 21
3S Lapped S1S2 Brackets .................................................................................................................... 26
3S Lapped S1S2S3 Brackets ............................................................................................................... 32
4S Brackets ........................................................................................................................................... 43
5S Brackets ........................................................................................................................................... 44
2S Flanged Brackets ............................................................................................................................. 45
3S Flanged Brackets ............................................................................................................................. 46
Flange Contours for Brackets .................................................................................................................. 48

Standard Bracket Flange Contour ........................................................................................................ 48
Chamfers .................................................................................................................................................... 49
Double Sided Chamfer .......................................................................................................................... 49
Single Sided Chamfers ......................................................................................................................... 49
Collars and Clips ....................................................................................................................................... 51

Non-Tight Clips ..................................................................................................................................... 51
Tight Collars .......................................................................................................................................... 55
Corner Features for Plates and Stiffeners .............................................................................................. 65
Corner Features for Members .................................................................................................................. 71
Member Cross Sections............................................................................................................................ 80

Cross Section Symbol 2L...................................................................................................................... 81
Cross Section Symbol BUBoxFM ......................................................................................................... 84
Cross Section Symbol BUC .................................................................................................................. 87
Cross Section Symbol BUCan .............................................................................................................. 90
Cross Section Symbol BUCone ............................................................................................................ 93
Cross Section Symbol BUEndCan........................................................................................................ 95

Contents
Cross Section Symbol BUFlat............................................................................................................... 98

Cross Section Symbol BUI.................................................................................................................. 100
Cross Section Symbol BUIHaunch ..................................................................................................... 102
Cross Section Symbol BUITaperWeb ................................................................................................. 105
Cross Section Symbol BUIUE............................................................................................................. 108
Cross Section Symbol BUL................................................................................................................. 111
Cross Section Symbol BUT ................................................................................................................ 114
Cross Section Symbol BUTube .......................................................................................................... 116
Cross Section Symbol C (MC) ............................................................................................................ 119
Cross Section Symbol CS................................................................................................................... 122
Cross Section Symbol HSSC (Pipe) ................................................................................................... 123
Cross Section Symbol HSSCs ............................................................................................................ 125
Cross Section Symbol HSSR.............................................................................................................. 128
Cross Section Symbol HSSRs ............................................................................................................ 130
Cross Section Symbol HW.................................................................................................................. 133
Cross Section Symbol HWWF ............................................................................................................ 135
Cross Section Symbol L ...................................................................................................................... 137
Cross Section Symbol Rect ................................................................................................................ 141
Cross Section Symbol RectC.............................................................................................................. 143
Cross Section Symbol RectCWF ........................................................................................................ 145
Cross Section Symbol RectWF........................................................................................................... 148
Cross Section Symbol RS................................................................................................................... 150
Cross Section Symbol S ..................................................................................................................... 152
Cross Section Symbol ST ................................................................................................................... 155
Cross Section Symbol T (MT) ............................................................................................................. 157
Cross Section Symbol W (M) .............................................................................................................. 160
Cross Section Symbol Wedge ............................................................................................................ 163
Cross Section Symbol WedgeWF....................................................................................................... 165
Wall Cross Sections ................................................................................................................................ 168

Cross Section Symbol HW.................................................................................................................. 169
Cross Section Symbol HWWF ............................................................................................................ 171
Cross Section Symbol Rect ................................................................................................................ 173
Cross Section Symbol RectC.............................................................................................................. 176
Cross Section Symbol RectCWF ........................................................................................................ 178
Cross Section Symbol RectWF........................................................................................................... 181
Cross Section Symbol Wedge ............................................................................................................ 183
Cross Section Symbol WedgeWF....................................................................................................... 185
Profile Cross Sections ............................................................................................................................ 188

Cross Section Symbol B ..................................................................................................................... 189
Cross Section Symbol BUL2............................................................................................................... 190
Cross Section Symbol BUL3............................................................................................................... 192
Cross Section Symbol BUT ................................................................................................................ 195
Cross Section Symbol C_SS .............................................................................................................. 196
Cross Section Symbol C_SType......................................................................................................... 198
Cross Section Symbol EA ................................................................................................................... 200
Cross Section Symbol FB ................................................................................................................... 202
Cross Section Symbol HalfR............................................................................................................... 205

Contents
Cross Section Symbol I ....................................................................................................................... 207

Cross Section Symbol I_SType .......................................................................................................... 209
Cross Section Symbol P ..................................................................................................................... 211
Cross Section Symbol R ..................................................................................................................... 213
Cross Section Symbol SB ................................................................................................................... 215
Cross Section Symbol SqTu ............................................................................................................... 217
Cross Section Symbol T ..................................................................................................................... 218
Cross Section Symbol T_SType ......................................................................................................... 218
Cross Section Symbol UA................................................................................................................... 220
Edge Features .......................................................................................................................................... 223
Profile End Cuts ....................................................................................................................................... 228

Welded Web Cuts ............................................................................................................................... 228
Clip Web Cuts ..................................................................................................................................... 237
Cutback Web Cuts .............................................................................................................................. 238
Snip Web Cuts .................................................................................................................................... 238
Edge Reinforcement Web Cuts .......................................................................................................... 241
Flange Cuts ......................................................................................................................................... 242
Member End Cuts .................................................................................................................................... 248

Along-Axis Web Cuts for Members ..................................................................................................... 249
Web-penetrated Center Cuts ....................................................................................................... 249
Web-penetrated Top Cuts ............................................................................................................ 254
Web-penetrated Bottom Cuts ....................................................................................................... 262
Web Non-penetrated Cuts ............................................................................................................ 271
Along-Axis Flange Cuts for Members ................................................................................................. 272
Flange-penetrated Center Cuts .................................................................................................... 272
Flange-penetrated Top Cuts ........................................................................................................ 276
Flange-penetrated Bottom Cuts ................................................................................................... 288
Flange Non-penetrated Cuts ........................................................................................................ 296
Web Cuts for Split Members ............................................................................................................... 301
Flange Cuts for Split Members ........................................................................................................... 305
Mitered Web Cuts for Members .......................................................................................................... 306
Mitered Flange Cuts for Members ...................................................................................................... 307
Free-end Web Cuts for Members ....................................................................................................... 308
Free-end Flange Cuts for Members .................................................................................................... 310
Slots .......................................................................................................................................................... 312

Slot A ................................................................................................................................................... 312
Slot C .................................................................................................................................................. 314
Slot C2 ................................................................................................................................................ 325
Slot I .................................................................................................................................................... 326
Sketched Features................................................................................................................................... 333
Openings .................................................................................................................................................. 335

CircleOpening ..................................................................................................................................... 335

Contents
OvalOpening ....................................................................................................................................... 336

RectangleOpening .............................................................................................................................. 336
SketchOpening.................................................................................................................................... 336
SquareOpening ................................................................................................................................... 337
TriangleOpening.................................................................................................................................. 337
Structural Manufacturing ........................................................................................................................ 338

Manufacturing Requirements for Profile Cross Sections .................................................................... 339
Manufacturing Requirements for Member Cross Sections ................................................................. 340
Bevel ................................................................................................................................................... 341
Bevel1 (I-Type).................................................................................................................................... 341
Bevel2 (V-Type) .................................................................................................................................. 342
Bevel3 (V-Type) .................................................................................................................................. 342
Bevel4 (X-Type) .................................................................................................................................. 342
Bevel5 (Y-Type) .................................................................................................................................. 342
Bevel6 (X-Type with Chamfer) ............................................................................................................ 342
Bevel10 ............................................................................................................................................... 343
BevelA ................................................................................................................................................. 344
BevelB ................................................................................................................................................. 344
BevelParam......................................................................................................................................... 345
FeatureTab1........................................................................................................................................ 345
Grind ................................................................................................................................................... 345
Knuckle ............................................................................................................................................... 346
Margin ................................................................................................................................................. 346
PartCenterLL ....................................................................................................................................... 346
PartDirC .............................................................................................................................................. 347
PartDirCL ............................................................................................................................................ 347
PartDirCR ............................................................................................................................................ 347
PartDirL ............................................................................................................................................... 348
PartDirLL ............................................................................................................................................. 348
PartDirLLFlangeRR ............................................................................................................................. 348
PartDirR .............................................................................................................................................. 349
PartDirRR ............................................................................................................................................ 349
PartDirRRFlangeLL ............................................................................................................................. 349
PMFeature .......................................................................................................................................... 350
Shrinkage ............................................................................................................................................ 350
SMPlateTab ........................................................................................................................................ 350
UnSpecBevel ...................................................................................................................................... 351
WeldTab1 ............................................................................................................................................ 351
Index ......................................................................................................................................................... 352

Preface
This document is a reference data guide for the Intergraph SmartTM 3D 2D Symbols task. The
purpose of this document is to describe the reference data delivered with the software for this
task.
Reference data includes both catalog data and specification data. Catalog data includes the
parts that you place in the model, such as piping components and equipment. Specification data
includes the rules that govern how those parts are placed and connected.
Documentation Comments
For the latest support information for this product, comments or suggestions about this
documentation, and documentation updates for supported software versions, please visit
Intergraph Smart Support (https://smartsupport.intergraph.com).
What's New in 2D Symbols Reference Data

The following changes have been made to the 2D symbols reference data.
Version 2016 (11.0)


SECTION 1
2D Symbols Reference Data

The 2D Symbols utility is delivered with the software and is used to create symbols representing
profile cross-sections, brackets, slots, collars, end cuts, detailing features, and manufacturing
features in the Molded Forms and Structural Detailing tasks; member cross-sections in the
Structure task; and facilitate using these symbols in a modeling environment.
This document describes all of the 2D symbols that are delivered with the software. The symbol
library is delivered to the SharedContent share in the [Reference Data Product
Directory]\SharedContent folder
You can create your own custom symbols using the 2D Symbols utility. To learn how to create
2D symbols, refer to the 2D Symbols User's Guide.
Two sets of 2D symbols are delivered: default and marine library. The default
set contains basic symbols suitable for prototyping. The marine library set provides a more
complete set of marine symbols.

SECTION 2
Bracket Symbols
Bracket symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\Marine Library\Brackets folder. Within the Brackets
folder, the folder hierarchy is further organized by the number of supports and by whether
the bracket is trimmed or lapped.
 [Reference Data Folder]\SharedContent\Brackets folder. Within the Brackets folder, the
folder hierarchy is further organized by the number of supports.
In This Section
2S Brackets ................................................................................... 11
3S Trimmed Brackets .................................................................... 16
3S Lapped S1 Brackets ................................................................. 21
3S Lapped S1S2 Brackets ............................................................ 26
3S Lapped S1S2S3 Brackets ........................................................ 32
4S Brackets ................................................................................... 43
5S Brackets ................................................................................... 44
2S Flanged Brackets ..................................................................... 45
3S Flanged Brackets ..................................................................... 46

Bracket Symbols
2S Brackets
2S brackets have two supports. Brackets can be trimmed or lapped to one or both supports.
The following 2S bracket symbols are delivered in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\2S folder.
Name Description Parameters
2SBracketLinear Linear free edge

2SLT Trimmed to supports
2SLT_wScallop Linear free edge

Trimmed to supports
Corner scallop
2SLL_1Lap Linear free edge

Support 1 is lapped

Bracket Symbols
2SLL_1Lap_wScallop Linear free edge

Support 1 is lapped
Corner scallop
2SLL_2Lap Linear free edge

Both supports are
lapped
2SLL_2Lap_wScallop Linear free edge

Both supports are
lapped
Corner scallop

Bracket Symbols
2SCT Curved free edge

Trimmed to supports
2SCT_wScallop Curved free edge

Trimmed to supports
Corner scallop
2SCL_1Lap Curved free edge

Support 1 is lapped
2SCL_1Lap_wScallop Curved free edge

Support 1 is lapped
Corner scallop

Bracket Symbols
2SCL_2Lap Curved free edge

Both supports are
lapped
2SCL_2Lap_wScallop Curved free edge

Both supports are
lapped
Corner scallop
2SBracketCurvLin

Bracket Symbols

Folder]\SharedContent\Brackets\2S folder.
Name Parameters
2SBracketCurved
2SBracketCurvLin

Bracket Symbols
Name Parameters
2SBracketLinear
3S Trimmed Brackets
3S trimmed brackets have three supports. Brackets are trimmed to all three supports.
3S trimmed bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\3S\Trimmed folder.
Offset from Support 1

3SLT Linear free edge

Offset

Bracket Symbols

OffsetScallop
Corner scallop

Offset

OffsetScallop
Corner scallop
Offset from Support 1, with Radius on the Free Edge


FlangeOutFillet with radius at
Support 3
(Name in the catalog is
3SLTOffset
FlangeOutFillet)

Bracket Symbols

FlangeOutFilletScallop with radius at
Support 3
3SLTOff Corner scallop
FlangeOutFilletScallop)

FlangeInFillet with radius at
Support 3, offset
to clear the
3SLTOffset
flange
FlangeInFillet)

FlangeInFilletScallop with radius at
Support 3, offset
to clear the
3SLTOff
flange
FlangeInFilletScallop)
Corner scallop
Offset from Flange of Support 3


OffsetFromFlange

Bracket Symbols

OffsetFromFlangeScallop
Corner scallop

OffsetFromFlange

Corner scallop
Set Back from Support 3


SetBack

Bracket Symbols

SetBackScallop
Corner scallop

SetBack

SetBackScallop
Corner scallop

Bracket Symbols
Trimmed to Flange of Support 3


ToFlange with radius at
Support 3

ToFlangeScallop with radius at
Support 3
Corner scallop
3S Lapped S1 Brackets
3S lapped S1brackets have three supports. Brackets are lapped to Support 1.
3S lapped S1 bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1 folder.

3SLLS1 Linear free edge

Offset

Bracket Symbols

OffsetScallop
Corner scallop
3SCLS1 Curved free edge

Offset

OffsetScallop
Corner scallop

Bracket Symbols

3SLLS1 Linear free edge with

FlangeInFillet radius at Support 3,
offset to clear the
flange

FlangeInFilletScallop radius at Support 3,
offset to clear the
flange
Corner scallop

FlangeOutFillet radius at Support 3

FlangeOutFilletScallop radius at Support 3
Corner scallop

Bracket Symbols


OffsetFromFlange

OffsetFromFlangeScallo
Corner scallop
p


SetBack

Bracket Symbols

SetBackScallop
Corner scallop

SetBack

SetBackScallop
Corner scallop

Bracket Symbols
3S Lapped S1S2 Brackets

3S lapped S1S2 brackets have three supports. Brackets are lapped to Support1 and Support2.
3S lapped S1S2 bracket symbols are delivered in the SharedContent share in the [Reference
Data Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1Sup2 folder.

3SLLS1S2 Linear free edge

Offset

OffsetScallop
Corner scallop
3SCLS1S2 Curved free edge

Offset

Bracket Symbols

OffsetScallop
Corner scallop


Support 3, offset to
clear the flange

clear the flange
Corner scallop

Bracket Symbols

Support 3

Support 3
Corner scallop


OffsetFromFlange

Bracket Symbols

Corner scallop

OffsetFromFlange

Corner scallop

Bracket Symbols


SetBack

SetBackScallop
Corner scallop

SetBack

Bracket Symbols

SetBackScallop
Corner scallop


Support 3

Support 3
Corner scallop

Bracket Symbols
3S Lapped S1S2S3 Brackets

3S lapped S1S2S3 brackets have three supports. Brackets are lapped to all three supports.
3S lapped S1S2S3 bracket symbols are delivered in the SharedContent share in the [Reference
Data Folder]\SharedContent\Marine Library\Brackets\3S\Lapped\Sup1Sup2Sup3 folder.

3SLLS1S2S3 Linear free edge

Offset
3SLLS1S2S3 Linear free edge

OffsetScallop
Corner scallop
3SCLS1S2S3 Curved free edge

Offset

Bracket Symbols
3SCLS1S2S3 Curved free edge

OffsetScallop
Corner scallop



Offset

Bracket Symbols

OffsetScallop
Corner scallop

Offset

OffsetScallop
Corner scallop

Bracket Symbols
3S lapped S2 brackets have three supports. Brackets are lapped to Support2.


Offset

OffsetScallop
Corner scallop

Offset

Bracket Symbols

OffsetScallop
Corner scallop


clear the flange

clear the flange
Corner scallop

Bracket Symbols

Support 3

Support 3
Corner scallop


OffsetFromFlange

Corner scallop

Bracket Symbols

OffsetFromFlange

Corner scallop


SetBack

Bracket Symbols

SetBackScallop
Corner scallop

SetBack

SetBackScallop
Corner scallop

Bracket Symbols


Support 3

Support 3
Corner scallop



Offset

Bracket Symbols

OffsetScallop
Corner scallop

Offset

OffsetScallop
Corner scallop

Bracket Symbols
3S lapped S3 brackets have three supports. Brackets are lapped to Support3.


Offset

OffsetScallop
Corner scallop

Offset

Bracket Symbols

OffsetScallop
Corner scallop
4S Brackets
4S brackets have four supports. Brackets can be trimmed or lapped to Support1 and Support2,
but are trimmed to Support3 and Support4.
Folder]\SharedContent\Marine Library\Brackets\4S folder.

Offset
Trimmed to
supports
Offset from
Support 3
4SCLT Linear free edge

OffsetFromFlangeScallop with radii at
Support3 and
Support 4
Trimmed to
supports
Offset from
flange of
Support 3
Corner scallops

Bracket Symbols
The following 4S bracket symbol is delivered in the [Reference Data

Folder]\SharedContent\Brackets\4SNew folder.
Name Parameters
4SBracketPlates
5S Brackets
5S brackets have four supports. Brackets can be trimmed to all supports.
Folder]\SharedContent\Brackets\5SNew folder.
Name Parameters
5SBracketPlates

Bracket Symbols
Name Parameters
5SBracketProfileProfile
2S Flanged Brackets
2S flanged brackets have two supports and a flange on the linear free edge.
2S flanged bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\Flanged\StdFlange\2S folder.
BUTRibConn Used with a BUT

section as Support 2
Trimmed to supports

Bracket Symbols
3S Flanged Brackets
3S flanged brackets have three supports and a flange on the linear free edge.
3S flanged bracket symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Brackets\Flanged\StdFlange\3S folder.

ToFlange

FlangeOutFillet

Bracket Symbols

FlangeInFillet
3SLLS2 Lapped to Support 2

OffsetFromFlange

SECTION 3
Flange Contours for Brackets

Flange contour symbols are used with flanged bracket symbols. Flange contour symbols are
delivered in the [Reference Data Folder]\SharedContent\Marine Library\Flange Contours folder.
Standard Bracket Flange Contour

SECTION 4
Chamfers
The chamfer symbols are delivered with the software in the SharedContent share in the
[Reference Data Folder]\SharedContent\Web Cuts and [Reference Data
Folder]\SharedContent\Marine Library\Chamfer folders.
Double Sided Chamfer
Single Sided Chamfers

SingleSidedBase

Chamfers
SingleSidedOffset

SECTION 5
Collars and Clips

Collar and clip symbols are delivered in two locations:
 [Reference Data Folder]\SharedContent\Marine Library\Collars folder.
 [Reference Data Folder]\SharedContent\Collars folder.
In This Section
Non-Tight Clips ...............................................................................51
Tight Collars ...................................................................................55
Non-Tight Clips
Clips are open on at least one side of the slot.
The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.
Name Cross- Selection Logic in Parameters

Sections the Rules
Supported
ClipAA_SM All Clip A

Non-tight
SlotA or Slot C
Profile height 
200mm (EA, UA,
FB, BUT, BUTL2)
Profile height 
180mm (B)

Collars and Clips

Sections the Rules
Supported
ClipAAC_BT All Default selection for

(curved top) all cross-sections
ClipAAC_ST Clip C
(straight top)
Non-tight
SlotA or Slot C
Profile height 
100mm (EA, UA,
FB, BUT, BUTL2)
Profile height 
180mm (B)
ClipAAC_BT_Left EA Collar
Order=Secondary
UA
25 < SlotAngle < 65
BUT
(deg)
BUTL2
Available in ClipC
B
FB
ClipAAC_ST_S EA 0.1 < SlotAngle <

25 (deg)
UA
Available in ClipC
BUT
BUTL2

Collars and Clips

Sections the Rules
Supported
ClipAAC_ST_Left Collar
Order=Secondary
SlotAngle < 0.1
(deg)
Available in ClipC
ClipAAC_ST_S_Left Collar
Order=Secondary
0.1 < SlotAngle <
25 (deg)
Available in ClipC
ClipAB_SM EA Available in ClipB

UA
B
BUT
FB
BUTL2

Collars and Clips
The following clip symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.
Name Parameters
ClipAA
Clip BA
Clip AB
Clip BB
Clip AAC
Clip BAC

Collars and Clips
Name Parameters
Clip ABC
Clip BBC
Tight Collars
Collars are welded around all sides of the slot.
The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Marine
Library\Collars folder.
Name Cross- Selection Logic in the Parameters

Sections Rules
Supported
CollarAIT_SM EA CollarNoSnipe
UA Tight
Slot I
CollarTIT_SM BUT
BUTL2
CollarACT_SM EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_SM B
CollarFCT_SM FB
CollarTCT_SM BUT
BUTL2

Collars and Clips

Sections Rules
Supported
CollarACT_A EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A B (SlotXC_LT_PAT)
CollarFCT_A FB
CollarACT_A2 EA CollarOneSnipe
UA Tight
Slot C
CollarBCT_A2 B (SlotXC_LT_PAT2)
CollarFCT_A2 FB
CollarBCT_A3 B CollarOneType
Available when
Slot=SlotBC_L_LTT_STR

Collars and Clips

Sections Rules
Supported
CollarTCT_A BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B
Slot C2
(left side)
(SlotXC2_T_PTT_STR)
Collar_Scallop BUT ScallopWithCollar

BUTL2
Collar_LongScallo BUT LongScallopWithCollar

p
BUTL2
EA
UA

Collars and Clips

Sections Rules
Supported
CollarTCT_A2 BUT CollarOneSnipe

(right side)
BUTL2 Tight
CollarTCT_B2
EA Slot C2
(left side)
(SlotXC2_T_PTT_STR2)
UA
ClipType=CollarOneType
CollarTCT_A3 Available when Slot =

SlotTC2_T_PAA_STR
and CollarOrder = Primary
BUT
ClipType=CollarOneType
Available when Slot =
CollarTCT_B3 SlotTC2_T_PAA_STR
and CollarOrder =
Secondary
CollarAAT_SM EA CollarTwoSnipes
UA Tight
Slot A
CollarBAT_SM B
CollarFAT_SM FB
CollarTAT_SM BUT
BUTL2

Collars and Clips
The following collar symbols are delivered in the [Reference Data Folder]\SharedContent\Collars
folder.
Name Parameters
Collar AIT
Collar FIT
Collar TIT

Collars and Clips
Name Parameters
Collar TsIT
Collar ACT

Collars and Clips
Name Parameters
Collar BCT
Collar FCT

Collars and Clips
Name Parameters
Collar AAT
Collar BAT

Collars and Clips
Name Parameters
Collar FAT
Collar TAT
Collar TsAT

Collars and Clips
Name Parameters
Collar LAT

SECTION 6
Corner Features for Plates and

Stiffeners
The following corner feature symbols are delivered in the [Reference Data Product
Folder]\SharedContent\Marine Library\Corner Features and [Reference Data Product
Folder]\SharedContent\Corner Features folders.
Crack Arrest Available in

SmartGeneralCorner
as an optional item.
Crack Arrest Along Available in

Corner SmartGeneralCorner
as an optional item.
Use when the Corner
feature needs a cut
along the corner.

Corner Features for Plates and Stiffeners
Drain Hole Hole placed on Collar

as a Corner feature.
Scallop Often placed as a

child of a welded web
cut.
Default is 50mm
Scallop Along Corner Available in

SmartScallop.
Use when the Corner
feature needs a cut
along the corner.

Snipe Often placed as a

child of a clip.
Default is 15mm
Snipe Along Corner Available in

SmartSnipe.
Use when the Corner
feature needs a cut
along the corner.
Snipe On Collar Snipe applied on

Collar as a corner
feature.

Long Scallop Often placed to avoid

gaps and seams.
When a part crosses
a slot gap, rules
calculate values to
clear the slot gap.
Long Scallop Along Available in

Corner SmartGeneralCorner.
Use when the Corner
feature needs a cut
along the corner.
Long Scallop With Seam Available in

SeamScallop.
Auto selected when a
seam is near a
Corner feature
location within 15mm
from the otherwise
default corner feature
edge.

Offset Radius Placed as a child of

an end cut with a gap
 15mm.
Offset Radius Obtuse Placed as a child of

an end cut with a gap
> 15mm.
Offset Radius with Placed as a child of

Straight Part an end cut with a gap
> 15mm.

Offset Radius Obtuse Placed as a child of

with Straight Part an end cut with a gap
 15mm.
Scallop With Collar Placed as a child of

Assembly
Connection.
Long Scallop With Seam This smart item is

With Collar available in the drop-
down of a corner
feature selection to
support the corner
feature with the seam
functionality. This
creates a corner
feature with a collar.
Long Scallop With Collar This smart item is

available in drop-
down of a corner
feature selection and
it creates a long
scallop corner feature
with a collar.

SECTION 7
Corner Features for Members

The following corner feature symbols are delivered in the [Reference Data Product
Folder]\SharedContent\Marine Library\Corner Features and [Reference Data Product
Folder]\SharedContent\Corner Features folders.
Arc Corner Relief Provides a minimal fit-up

clearance at a corner of the
bounding edge. When the
bounded object is within the
bounding object, the corner
feature may only be placed
at the inside corner. When
the bounded object extends
outside the bounding object,
the corner feature may also
be placed on the outside
corner.
Corner To Far Face Clears material from the

Edge Relief bounding edge and around
one corner. It is typically
applied to the inside corner
to relieve the outside corner.
The reverse is also possible.
This feature is applicable
when the bounded object
extends outside the
bounding object.

Cross Section Scallop Provides clearance around

the fillet between the
bounding face and bounding
edge.
Cross Section Scallop Provides a constant

Along Corner clearance around the fillet
between the bounding face
and bounding edge. The
cutting direction follows the
path of the bounding object.

Cross Section Snipe Provides clearance around

the fillet between the
bounding face and bounding
edge.
Cross Section Snipe Provides a constant

Along Corner clearance around the fillet
between the bounding face
and bounding edge. The
cutting direction follows the
path of the bounding object.

Edge Hook Relief Disconnects the bounded

object from the inside of the
bounding edge.
Edge To Face Rathole Provides welding access to

the back side of the bounded
flange or web.
when there is no bounding
edge.

Face To Inside Rathole Provides welding access to

flange or web and
disconnects the member
from the inside of the
bounding edge

when the inner surface of
the bounded flange/web is at
or is inside the inner surface
of the bounded edge
Face To Inside Rathole Provides welding access to

2 the back side of the bounded
flange or web and
disconnects the member
from the inside of the
bounding edge.

the bounded flange/web is
outside the inner surface of
the bounded edge.

Fillet Ellipse Trims the bounded part

along the bounding fillet.
In Out Hook Relief Clears all material from the

bounding edge and in the
vicinity of both corners.

Inside Face Rathole Provides welding access to

flange or web.
the bounded flange/web is at
or is inside the inner surface
of the bounded edge
Inside Face Rathole 2 Provides welding access to

flange or web.
outside the inner surface of
the bounded edge.

Outside Hook Relief Disconnects the bounding

object from the bounded
edge and the inner surface
of the bounding edge, while
leaving it connected to the
outside face.
when bounded object
extends outside the
bounding object.
Short Edge Rathole Provides welding access to

flange or web.
significantly outside the inner
surface of the bounded
edge.

Two Edge Rathole Provides welding access to

flange or web and
disconnect the member from
the inside of the bounding
edge.

SECTION 8
Member Cross Sections

Member cross-section symbols are used in the Structure task.
All section tables delivered with the software use a specific set of cross-section symbols. Some
section tables use all the cross-section symbols in the set; some tables only use a subset of the
cross-section symbols. Each cross-section symbol has its own set of properties. When looking
at a section table workbook, you can determine the cross-section symbol that is being
referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the
sheet.
The cross-section symbols are delivered with the reference data software in the [Reference
Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-
section symbols, sometimes referred to as arbitrary sections, using the 2D Symbols utility that is
delivered with the software.
The software uses the simple physical representation of the cross-section symbol to display the
member geometry in the model. You can change the display representation using the Selected
Aspects option of Format > View.
The delivered symbols contain a detailed physical representation. This representation is
available only for marine models, and is not used for plant and materials handling models.
The delivered symbols also contain a production physical representation. This representation is
available only for marine models in the Structural Manufacturing task, and is not used for plant
and materials handling models.
For more information, see Cross-Section Symbol Representations in the 2D Symbols User's
Guide.
In This Section
Cross Section Symbol 2L .............................................................. 81
Cross Section Symbol BUBoxFM .................................................. 84
Cross Section Symbol BUC ........................................................... 87
Cross Section Symbol BUCan....................................................... 90
Cross Section Symbol BUCone..................................................... 93
Cross Section Symbol BUEndCan ................................................ 95
Cross Section Symbol BUFlat ....................................................... 98
Cross Section Symbol BUI ............................................................ 100
Cross Section Symbol BUIHaunch ................................................ 102
Cross Section Symbol BUITaperWeb ........................................... 105
Cross Section Symbol BUIUE ....................................................... 108
Cross Section Symbol BUL ........................................................... 111
Cross Section Symbol BUT ........................................................... 114
Cross Section Symbol BUTube ..................................................... 116
Cross Section Symbol C (MC) ....................................................... 119
Cross Section Symbol CS ............................................................. 122
Cross Section Symbol HSSC (Pipe).............................................. 123
Cross Section Symbol HSSCs ...................................................... 125
Cross Section Symbol HSSR ........................................................ 128

Cross Section Symbol HSSRs ...................................................... 130

Cross Section Symbol HW ............................................................ 133
Cross Section Symbol HWWF....................................................... 135
Cross Section Symbol L ................................................................ 137
Cross Section Symbol Rect ........................................................... 141
Cross Section Symbol RectC ........................................................ 143
Cross Section Symbol RectCWF................................................... 145
Cross Section Symbol RectWF ..................................................... 148
Cross Section Symbol RS ............................................................. 150
Cross Section Symbol S ................................................................ 152
Cross Section Symbol ST .............................................................. 155
Cross Section Symbol T (MT) ....................................................... 157
Cross Section Symbol W (M) ........................................................ 160
Cross Section Symbol Wedge ....................................................... 163
Cross Section Symbol WedgeWF ................................................. 165
Cross Section Symbol 2L

The 2L cross section symbol defines double-angle sections and uses the following properties.
Section Name
Type the section name. This name appears when you label members. The section name
must be unique within the section standard.
Short Name
Type the short name for the section.
EDI Name
Type the Electronic Data Interchange name for the section. This name is used when
translating sections through CIMsteel. This property is currently not used.
Group Id
Type the material group identification for the section.
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length, pound per foot
(lbm/ft).
Area
Type the cross-sectional area for the section. The area is defined in square inches or square
millimeters.
Depth
Type the depth for the section (longer legs). The depth is defined in inches or millimeters.

d
Type the other depth for the section (shorter legs). The depth is defined in inches or
millimeters.
bf
Type the width of a single angle. The width is defined in inches or millimeters.
Width
Type the width of the entire section. The width is defined in inches or millimeters.
Perimeter
Type the outside perimeter of the section.
tf
Type the flange thickness for the section. The thickness is defined in inches or millimeters.
tw
Type the web thickness for the section. The thickness is defined in inches or millimeters.
kdesign
Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape
or the equivalent distance on the welded section.
kdetail
Type the distance from outer face of the flange to the web toe of the fillet of the rolled shape
or the equivalent distance on welded section.
bb
Enter the back-to-back spacing on the section.
CentroidY
Type the centroid location along the y-axis. The location is defined in inches or millimeters.
Ixx
Type the moment of inertia for the section's local x-axis.
Zxx
Type the plastic section modulus for the section's local x-axis.
Sxx
Type the section modulus for the section's local x-axis.
Rxx
Type the radius of gyration for the section's local x-axis.
Ryy
Type the radius of gyration for the section's local y-axis.
ro
Type the polar radius of gyration about the shear center.

H
Type the flexural constant.
bb Configuration
Specifies which legs of the angles are placed back-to-back. Type 0 for equal leg angle. Type
1 to place the long legs back-to-back. Type 2 to place the short legs back-to-back.
lsg
Specify the bolt gage for the long side when there is one bolt row. For more information, see
Member Cross Sections.
lsg1
Specify the gage distance to the first bolt row on the long side when there are two bolt rows.
lsg2
Specify the gage distance between the first and second bolt rows on the long side when
there are two bolt rows.
ssg
Specify the bolt gage for the short side when there is one bolt row.
ssg1
Specify the gage distance to the first bolt row on the short side when there are two bolt
rows.
ssg2
Specify the gage distance from the first bolt row to the second bolt row on the short side
when there are two bolt rows.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is
False.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section, the
default value is False.

IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section, the
default value is True.
Cross Section Symbol BUBoxFM

The BUBoxFM symbol uses the following properties.
Section Name
Type the section name. The section name must be unique within the section standard.
Short Name
EDI Name
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length, pound per foot
(lbm/ft).
Area
Type the cross-section area for the section.
Depth
Type the depth for the section. The depth is defined in meters.
Width
Type the width for the section. The width is defined in meters.

Perimeter
The outside perimeter distance for the section.
Top Flange Width
Type the width of the top flange.
Top Flange Thickness
Type the thickness of the top flange.
Bottom Flange Width
Type the width of the bottom flange.
Bottom Flange Thickness
Type the thickness of the bottom flange.
Web Thickness
Type the thickness of the web.
Offset Left Web Top
Type the offset distance for the top left web.
Offset Right Web Top
Type the offset distance for the top right web.
Offset Left Web Bot
Type the offset distance for the bottom left web.
Offset Right Web Bot
Type the offset distance for the bottom right web.
CentroidX
Type the vertical distance from designated member edge to the centroidal axis.
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Type the moment of inertia for the section's local y-axis.

Zyy
Type the plastic section modulus for the section's local y-axis.
Syy
Type the section modulus for the section's local y-axis.
Ryy
J
Type the torsional moment of inertia for the section.
Cw
Type the warping constant for the section.
ro
H
Type the flexural constant for the section.
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True.
IsSymmetricAlongX
Specify if the cross-section is symmetrical along the local x-axis. For this cross-section,
whether or not the cross-section is symmetrical about the x-axis depends on dimensional
values.
IsSymmetricAlongY
Specify if the cross-section is symmetrical along the local y-axis. For this cross-section,
whether or not the cross-section is symmetrical about the y-axis depends on dimensional
values.
Symmetries about the x- and y-axes are defined by design properties only. The
Flange Width Extension (top and bottom) property is not a design property; therefore, the
symmetry calculation is not affected by this property. This non-affect can cause
discrepancies between the symmetry of the cross-section graphic and the
IsSymmetricAlongX and IsSymmetricAlongY properties when non-zero width extensions
are defined.

Cross Section Symbol BUC

The BUC symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
Type the weight of the section. The unit weight is defined in mass per length pound per foot
(lbm/ft).
Area
Depth
Type the depth for the section. The depth is defined in meters
Width

Perimeter
Top Flange Width
Bottom Flange Width
Type the width of the bottom flange.
Type the thickness of the bottom flange.
Web Thickness
Type the thickness of the web.
Offset Web Top
Type the offset distance for the top web.
Offset Web Bot
Type the offset distance for the bottom web.
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy

Ryy
J
Cw
ro
H
gf
Type the bolt gage for the flange.
gw
Type the bolt gage for the web.
IsHollow
False.
IsSymmetricAlongX
values.
IsSymmetricAlongY
values.

Cross Section Symbol BUCan

The BUCan symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area

Depth
Width
Perimeter
Tube Thickness
Type the plate thickness of the main tube plate.
Tube Diameter
Type the diameter of the main tube.
Diameter Start
Type the cone diameter at the can start.
Diameter End
Type the cone diameter at the can end.
Length Start Cone
Type the start cone length. You can also enter any negative number to indicate this length
should be 1/3 of the total length.
Length End Cone
Type the end cone length. You can also enter any negative number to indicate this length
Cone 1 Thickness
Type the plate thickness for the cone closest to the start of the member.
Cone 1 Material
Type the plate material for the cone closest to the start of the member.
Cone 1 Grade
Type the plate material grade for the cone closest to the start of the member.
Cone 2 Thickness
Type the plate thickness for the cone closest to the end of the member.
Cone 2 Material
Type the plate material for the cone closest to the end of the member.
Cone 2 Grade
Type the plate material grade for the cone closest to the end of the member.
CentroidX

CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
IsHollow
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol BUCone

The BUCone symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Cone Thickness
Type the plate thickness of the cone plate.
Diameter Start
Type the cone diameter at the start.
Diameter End
Type the cone diameter at the end.

Length Start Cone

Length End Cone
Type the end cone length. You can also enter any negative number to indicate this length
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

IsHollow
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol BUEndCan

The BUEndCan symbol uses the following properties.
Section Name
Short Name
EDI Name

Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Tube Thickness
Type the plate thickness of the main tube plate.
Tube Diameter
Type the diameter of the main tube.
Diameter Cone
Type the cone diameter.
Cone Length
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy

Zyy
Syy
Ryy
J
Cw
ro
H
IsHollow
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol BUFlat

The BUFlat symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Web Thickness
CentroidX

CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol BUI

The BUI symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Top Flange Width


Type the plate thickness of the top flange.
Web Thickness
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro

H
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol BUIHaunch

The BUIHaunch symbol uses the following properties.
Section Name
Short Name
EDI Name

Unit Weight
(lbm/ft).
Area
Depth
Type the depth for the section. The depth is defined in meters.
Width
Perimeter
Top Flange Width
Bottom Flange Width
Length Start
Type the distance from the start of the member to where the haunch transition should start.
You can enter any negative number to indicate the distance should be 1/3 of the member
length.
Depth Start
Type the web depth at the start of the member.
Depth End
Type the web depth at the end of the member.
Depth Haunch
Type the web depth at the haunch.
Length End
Type the distance from the end of the member to where the haunch transition should end.
You can enter any negative number to indicate the distance should be 1/3 of the member
length.
Transition Gradient Start
Type the slope of the start transition.

Transition Gradient End

Type the slope of the end transition.
Web Thickness
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
IsHollow
False.

IsSymmetricAlongX
values.
IsSymmetricAlongY
are defined.
Cross Section Symbol BUITaperWeb

The BUITaperWeb symbol uses the following properties.
Section Name

Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Top Flange Width
Bottom Flange Width
Web Thickness
Depth Start
Depth End
CentroidX
CentroidY

Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
IsHollow
False.
IsSymmetricAlongX
whether or not the cross-section is symmetrical depends on dimensional values.
IsSymmetricAlongY


are defined.
Cross Section Symbol BUIUE

The BUIUE symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width

Perimeter
Top Flange Width
Bottom Flange Width
Web Thickness
Depth Start
Depth End
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy

Ryy
J
Cw
ro
H
gf
gw
IsHollow
False.
IsSymmetricAlongX
values.
IsSymmetricAlongY
are defined.

Cross Section Symbol BUL

The BUL symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter

Bottom Flange Width

Web Thickness
Depth Start
Depth End
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw

ro
H
lsg
Specify the bolt gage for the long side when there is one bolt row.
lsg1
lsg2
Specify the gage distance from the first bolt row to the second bolt row on the long side
ssg
ssg1
rows.
ssg2
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

values.
Cross Section Symbol BUT

The BUT symbol uses the following properties.
Section Name
Short Name
EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter

Top Flange Width

Web Thickness
Depth Start
Depth End
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw

ro
H
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol BUTube

The BUTube symbol uses the following properties.
Section Name
Short Name

EDI Name
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
Tube Thickness
Type the plate thickness of the tube plate.
Tube Diameter
Type the diameter of the tube.
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy

Syy
Ryy
J
Cw
ro
H
IsHollow
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol C (MC)

The C cross-section symbol defines channel sections and uses the following properties. The C
symbol is also used for MC cross-sections.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
millimeters.
Depth
Type the depth for the section. The depth is defined in inches or millimeters.
Width
Type the flange width for the section. The width is defined in inches or millimeters.
Perimeter

d
bf
Type the flange width for the section. The width is defined in inches or millimeters.
tw
tf
kdesign
Type the distance from the outer face of the flange to the web toe of the fillet of the rolled
shape or the equivalent distance on the welded section.
kdetail
shape or the equivalent distance on welded section.
CentroidX
Type the centroid location along the x-axis. The location is defined in inches or millimeters.
eo_x
Type the shear center location along the x-axis. The location is defined in inches or
millimeters.
xp
Type the horizontal distance from the designated edge of member to its plastic neutral axis
(PNA). The distance is defined in inches or millimeters.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy

Ryy
J
Cw
ro
H
Type the flexural constant in LRFD Specification Equation E3-1.
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol CS

The CS cross section symbol defines solid round sections and uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
millimeters.
Depth
Type the depth of the section.
Width
Type the width of the section.
Perimeter
Type the outside perimeter distance for the section.
Ixx
Zxx
Sxx

Rxx
Ryy
ro
H
Type the flexural constant.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol HSSC (Pipe)

The HSSC cross section symbol defines circular, hollow structural sections and uses the
following properties. The HSSC symbol is also used for Pipe cross-sections.
Section Name
Type the section name. This name appears when labeling members. The section name
Short Name
EDI Name

Group Id
Unit Weight
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches or square
millimeters.
Depth
Width
Perimeter
tnom
Type the nominal wall thickness of the section.
tdes
Type the design wall thickness of the section.
D_t
Type the ratio of the diameter to the thickness.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy

Ryy
J
IsHollow
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol HSSCs

The HSSC cross section symbol defines circular, hollow structural sections and uses the
following properties. The HSSC symbol is also used for Pipe cross-sections.
Section Name
Type the section name. This name appears when labeling members. The section name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).

Area
millimeters.
Depth
Width
Perimeter
tnom
tdes
D_t
Type the ratio of the diameter to the thickness.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
IsHollow

IsSymmetricAlongX
IsSymmetricAlongY
Has Seam
Specify if the cross-section has a seam indicator or not. For this cross-section, the default
value is True (1).
Seam Angle
Defines the location of the seam. This angle is measured clockwise from orientation vector
of the member looking down the member from the start end.

Cross Section Symbol HSSR

The HSSR cross section symbol defines rectangular, hollow, structural sections and uses the
following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Type the cross-section area for the section. The area is defined in square inches and square
millimeters.
Depth
Type the overall depth of the section.
Width
Type the width for the section. The width is defined in inches or millimeters.
Perimeter
tnom
tdes

b_t
Type the width to thickness ratio of the section.
h_t
Type the height to thickness ratio of the section.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True
(1).
IsSymmetricAlongX
default value is True (1).
IsSymmetricAlongY

Cross Section Symbol HSSRs

The HSSRs cross section symbol defines rectangular, hollow, structural sections with a seam
indicator and uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
millimeters.
Depth
Type the overall depth of the section.
Width
Type the width for the section. The width is defined in inches or millimeters.
Perimeter
tnom
tdes

b_t
Type the width to thickness ratio of the section.
h_t
Type the height to thickness ratio of the section.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
IsHollow
Specify if the cross-section is hollow or not. For this cross-section, the default value is True
(1).
IsSymmetricAlongX
IsSymmetricAlongY
Has Seam
Specify if the cross-section has a seam indicator or not. For this cross-section, the default

value is True (1).
Seam Angle
Defines the location of the seam. This angle is measured clockwise from orientation vector
of the member looking down the member from the start end.

Cross Section Symbol HW

The HW symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter

d
Type the depth for the section.
bf
Type the width for the section.
tw
Type the web thickness for the section. The thickness is defined in meters.
tf
Type the flange thickness for the section. The thickness is defined in meters.
kdesign
kdetail
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J

Cw
ro
H
Cross Section Symbol HWWF

The HWWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Flange Right Width
Define the flange width on the right side.
Flange Left Width
Define the flange width on the left side.

Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
Type the horizontal distance from the designated member edge to the centroidal axis.
CentroidY
Type the vertical distance from the designated member edge to the centroidal axis.
Ixx
Zxx
Sxx

Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
Cross Section Symbol L

The L cross section symbol uses the following properties.
Section Name
Short Name
EDI Name

Group Id
Unit Weight
(lbm/ft).
Area
millimeters.
Depth
Width
Type the breadth for the section. The breadth is defined in inches or millimeters.
Perimeter
d
Type the overall depth (longer leg) for the section. The depth is defined in inches or
millimeters.
bf
Type the overall width (shorter leg) for the section. The width is defined in inches or
millimeters.
tf
tw
kdesign
kdetail
CentroidX
Type the location of the centroid along the local x-axis. The location is defined in inches or
millimeters.
CentroidY
Type the location of the centroid along the local y-axis. The location is defined in inches or
millimeters.
xp
Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along

the local x-axis.

yp
Type the distance from the designated edge of angle to its plastic neutral axis (PNA) along
the local y-axis.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
Rxy
Type the radius of gyration about the local z-axis. The radius is defined in inches or
millimeters.
J
Cw
ro
H
lsg
Specify the bolt gage for the long side when there is one bolt row.
lsg1

lsg2
Specify the gage distance from the first bolt row to the second bolt row on the long side
ssg
ssg1
rows.
ssg2
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol Rect

The Rect symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw

tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro

H
Cross Section Symbol RectC

The RectC symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Setback
Define the setback. This value is defined in meters.
Unit Weight
(lbm/ft).
Area

Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy

Zyy
Syy
Ryy
J
Cw
ro
H
Cross Section Symbol RectCWF

The RectCWF symbol uses the following properties.
Section Name
Short Name
EDI Name

Group Id
Angle
Define the angle.
Setback
Flange Right Width
Define the flange width on the right side. This valve is defined in meters.
Flange Left Width
Define the flange width on the left side. This valve is defined in meters.
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail

CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

Cross Section Symbol RectWF

The RectWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Flange Right Width
Flange Left Width
Unit Weight
(lbm/ft).
Area
Depth
Width

Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy

J
Cw
ro
H
Cross Section Symbol RS

The RS cross section symbol defines rectangular solids and uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
millimeters.
Depth

Width
Perimeter
Type the outside perimeter distance for the section.
Ixx
Zxx
Sxx
Rxx
Ryy
ro
H
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol S

The S cross section symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Type the depth for the section. The depth is defined in inches.
Width
Type the flange width for the section. The width is defined in inches.
Perimeter

d
Type the overall depth for the section.
bf
Type the overall width for the section.
tw
Type the web thickness for the section. The thickness is defined in inches.
tf
Type the flange thickness for the section. The thickness is defined in inches.
kdesign
kdetail
Fy3p
Type the maximum yield for the compact web for the section.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J

Cw
Wno
Type the normalized warping function. The function is defined in square inches or square
millimeters.
Sw
Type the warping statical moment. The moment is defined in in4 or mm4.
Qf
Type the first moment of area for the flange.
Qw
Type the first moment of area for the web.
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol ST

The ST cross section symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf

tw
tf
kdesign
kdetail
CentroidY
Type the distance to the centroid along the local y-axis. This distance is defined in inches or
millimeters.
yp
Type the distance from the designated edge of angle to its plastic neutral axis along the
local y-axis.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw

ro
H
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol T (MT)

The T cross-section symbol uses the following properties. The T symbol is also used for MT
cross-sections.
Section Name

Short Name
EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidY
yp
Type the distance from designated edge of angle to its plastic neutral axis along the local y-

axis.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
gf
gw
IsHollow

False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol W (M)

The W symbol uses the following properties. The W symbol is also used for M cross-sections.
Section Name
Short Name
Alternate EDI Name
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Width

Perimeter
d
bf
tw
tf
kdesign
kdetail
Fy3p
Type the maximum yield stress for the section.
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy

J
Cw
Wno
Type the normalized warping function. The function is defined in square inches or square
millimeters.
Sw
Type the warping statical moment. The moment is defined in in4 or mm4.
Qf
Type the first moment of area for the flange.
Qw
Type the first moment of area for the web.
gf
gw
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol Wedge

The Wedge symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle Right
Define the angle on the right side of the web.
Angle Left
Define the angle on the left side of the web.
Unit Weight
(lbm/ft).
Area
Depth
Width

Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy

Ryy
J
Cw
ro
H
Cross Section Symbol WedgeWF

The WedgeWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id

Angle Right
Angle Left
Flange Right Width
Flange Left Width
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX

CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

SECTION 9
Wall Cross Sections

Wall cross-section symbols are used in the Structure task’s Wall commands. These wall cross
sections are delivered with the steel sections and follow most of the same rules.
All section tables delivered with the software use a specific set of cross-section symbols. Some
section tables use all the cross-section symbols in the set; some tables only use a subset of the
cross-section symbols. Each cross-section symbol has its own set of properties. When looking
at a section table workbook, you can determine the cross-section symbol that is being
referenced by that particular sheet by looking at the SymbolDefinition entry at the top of the
sheet.
The wall cross-section symbols are delivered with the reference data software in the [Reference
Data Folder]\SharedContent\CrossSections folder. You can create your own custom cross-
section symbols using the 2D Symbols utility that is delivered with the software.
For more information, see Cross-Section Symbol Representations in the 2D Symbols User's
Guide.
In This Section
Cross Section Symbol HW ............................................................ 169
Cross Section Symbol HWWF....................................................... 171
Cross Section Symbol Rect ........................................................... 173
Cross Section Symbol RectC ........................................................ 176
Cross Section Symbol RectCWF................................................... 178
Cross Section Symbol RectWF ..................................................... 181
Cross Section Symbol Wedge ....................................................... 183
Cross Section Symbol WedgeWF ................................................. 185

Wall Cross Sections
Cross Section Symbol HW

The HW symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter

Wall Cross Sections
d
bf
tw
tf
kdesign
kdetail
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J

Wall Cross Sections
Cw
ro
H
Cross Section Symbol HWWF

The HWWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Flange Right Width
Flange Left Width

Wall Cross Sections
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx

Wall Cross Sections
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
Cross Section Symbol Rect

The Rect symbol uses the following properties.
Section Name
Short Name
EDI Name

Wall Cross Sections
Group Id
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx

Wall Cross Sections
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

Wall Cross Sections
Cross Section Symbol RectC

The RectC symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle
Define the angle.
Setback
Unit Weight
(lbm/ft).
Area
Depth

Wall Cross Sections
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy

Wall Cross Sections
Syy
Ryy
J
Cw
ro
H
Cross Section Symbol RectCWF

The RectCWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id

Wall Cross Sections
Angle
Define the angle.
Setback
Flange Right Width
Flange Left Width
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX

Wall Cross Sections
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

Wall Cross Sections
Cross Section Symbol RectWF

The RectWF symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Flange Right Width
Flange Left Width
Unit Weight
(lbm/ft).
Area
Depth
Width

Wall Cross Sections
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy

Wall Cross Sections
J
Cw
ro
H
Cross Section Symbol Wedge

The Wedge symbol uses the following properties.
Section Name
Short Name
EDI Name
Group Id
Angle Right
Angle Left

Wall Cross Sections
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx

Wall Cross Sections
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H
Cross Section Symbol WedgeWF

The WedgeWF symbol uses the following properties.
Section Name

Wall Cross Sections
Short Name
EDI Name
Group Id
Angle Right
Angle Left
Flange Right Width
Flange Left Width
Unit Weight
(lbm/ft).
Area
Depth
Width
Perimeter
d
bf
tw
tf

Wall Cross Sections
kdesign
kdetail
CentroidX
CentroidY
Ixx
Zxx
Sxx
Rxx
Iyy
Zyy
Syy
Ryy
J
Cw
ro
H

SECTION 10
Profile Cross Sections

Profile cross-section symbols are used in the Molded Forms and Structural Detailing tasks.
The profile cross section symbols are delivered with the software in the [Reference Data
Directory]\SharedContent\Profile Xsections folder. You can create your own custom symbols
using the 2D Symbols utility that is delivered with the software.
In This Section
Cross Section Symbol B ................................................................ 189
Cross Section Symbol BUL2 ......................................................... 190
Cross Section Symbol BUL3 ......................................................... 192
Cross Section Symbol BUT ........................................................... 195
Cross Section Symbol C_SS ......................................................... 196
Cross Section Symbol C_SType ................................................... 198
Cross Section Symbol EA ............................................................. 200
Cross Section Symbol FB .............................................................. 202
Cross Section Symbol HalfR ......................................................... 205
Cross Section Symbol I ................................................................. 207
Cross Section Symbol I_SType ..................................................... 209
Cross Section Symbol P ................................................................ 211
Cross Section Symbol R ................................................................ 213
Cross Section Symbol SB ............................................................. 215
Cross Section Symbol SqTu .......................................................... 217
Cross Section Symbol T ................................................................ 218
Cross Section Symbol T_SType.................................................... 218
Cross Section Symbol UA ............................................................. 220

Cross Section Symbol B

The B bulb angle profile cross section symbol (B.sym) uses the following symbol parameters.
Each symbol parameter is defined and given a default value in the symbol file. Each occurrence
of a symbol bulkloaded into the catalog can be assigned different parameter values.
1 TCR - Top corner radius
2 FL - Flange length
3 Slope - Slope of the bottom of the bulb flange.
4 WL - Web length
5 CR - Corner radius
6 FR - Fillet radius of the bulb flange
7 WT - Web thickness
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol BUL2

The BUL2 profile cross section symbol uses the following properties.
Section Name
must be unique across the catalog.
Short Name
Alternate EDI Name
Description
Type a short description if needed.
Area
millimeters.
Depth
Type the depth for the section (Web Length). The depth is defined in inches or millimeters.
Width

Perimeter
CentroidX
millimeters.
CentroidY
millimeters.
Moment of Inertia about X (Ixx)
Type the moment of inertia for the section's local x- axis.
Moment of Inertia about Y (Iyy)
Type the moment of inertia for the section's local y- axis.
Warping Statical Moment (Sw)
Type the warping statical moment for the section.
Elastic Section Modulus about X (Sxx)
Elastic Section Modulus about Y (Syy)
Torsional Moment of Inertia (J)
Warping Constant (Cw)
Flexural Constant (H)
Polar Radius of Gyration about Shear Center (ro)
Radius of Gyration about X axis (Rxx)
Radius of Gyration about Y axis (Ryy)
Radius of Gyration about Principle XY (Rxy)
millimeters.
Plastic Section Modulus about X (Zxx)

Plastic Section Modulus about Y (Zyy)

IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
whether or not the cross-section is symmetric depends on the Flange Offset (FO) value.
Cross Section Symbol BUL3

The BUL3 profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name

Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
whether or not the cross-section is symmetric about the x-axis depends on the Flange Offset
(FO) value.
IsSymmetricAlongY

Cross Section Symbol BUT
See Also
Member Cross Sections (on page 80)

Cross Section Symbol C_SS

The C_SS profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.

CentroidY
millimeters.
millimeters.
IsHollow
False.

IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol C_SType

The C_SType profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width

Perimeter
CentroidX
millimeters.
CentroidY
millimeters.
millimeters.


IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol EA

The EA profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name
Description

Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol FB

The FB profile cross section symbol uses the following properties.
Section Name

Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol HalfR

The HalfR profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

Cross Section Symbol I
The I profile cross section symbol uses the following properties.

Section Name
Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width

Perimeter
CentroidX
millimeters.
CentroidY
millimeters.
millimeters.


IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol I_SType

The I_SType profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name

Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol P

The P profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name


Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol R

The R profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name

Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol SB

The SB profile cross section symbol uses the following properties.
Name
Short Name

Alternate EDI Name

Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
Cross Section Symbol SqTu
See Also

Cross Section Symbol T
See Also
Cross Section Symbol T_SType

The T_SType profile cross section symbol uses the following properties.
Section Name
Short Name
Alternate EDI Name

Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY
Cross Section Symbol UA

The UA profile cross section symbol uses the following properties.
Section Name


Short Name
Alternate EDI Name
Description
Area
millimeters.
Depth
Width
Perimeter
CentroidX
millimeters.
CentroidY
millimeters.


millimeters.
IsHollow
False.
IsSymmetricAlongX
IsSymmetricAlongY

SECTION 11
Edge Features
Edge feature symbols are delivered in the SharedContent share in the [Reference Data
Folder]\SharedContent\Marine Library\Edge Features folder.
Ellipse Available in CutEdge as

an optional item.
Ellipse Along Edge Available in CutEdge as

an optional item.
Use when Edge feature
needs a cut along the
edge.
Half Round Available in CutEdge as

a default item.

Edge Features
Half Round Along Edge Available in CutEdge as

an optional item.
Use when the Edge
feature needs a cut
along the edge.
MushRoom Available in CutEdge as

an optional item.
MushRoom Along Edge Available in CutEdge as

an optional item.
Use when Edge feature
needs a cut along the
edge.

Edge Features
Scallop Available in CutEdge as

an optional item.
Wide Scallop
Scallop Along Edge Available in CutEdge as

an optional item.
Use when the Edge
feature needs a cut
along the edge.
Round Available in catalog, but

not available in SML
Edge feature rules.
Circular Available in OffEdge as

a default item.

Edge Features
Oval Available in OffEdge as

a default item.
Flat Oval Available in catalog, but

not available in SML
Edge feature rules.
WaterStop1 Available in WaterStop
BendFeature_Cut_01 Available when

ProfileKnuckleType =
BendPlusFeatures

Edge Features
InsertPlate1 Available when

(Plate inserted in edge
BendPlusFeatures
feature created when
BendPlusFeatures)

SECTION 12
Profile End Cuts

Web cut and flange cut symbols are used with profile stiffeners.
End cut symbols are delivered in the following locations:
 Web cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Web Cuts and
[Reference Data Folder]\SharedContent\Web Cuts folders.
 Flange cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Flange Cuts
and [Reference Data Folder]\SharedContent\Flange Cuts folders.
In This Section
Welded Web Cuts...........................................................................228
Clip Web Cuts.................................................................................237
Cutback Web Cuts..........................................................................238
Snip Web Cuts................................................................................238
Edge Reinforcement Web Cuts ......................................................241
Flange Cuts ....................................................................................242
Welded Web Cuts

Used when the assembly connection EndCutType is Welded.
Name Cross- Description Parameters

Sections
Supported
WebAndFlangeWelded All

Profile End Cuts

Sections
Supported
SnipTopCornerLeft EA Welded to WebLeft of
the bounding profile
UA
B
SnipTopCornerRight EA Welded to WebRight of

UA
B
SnipTopCornerLeft_ER FB For edge

reinforcements
Welded to WebLeft of
SnipTopCornerRight_ER FB For edge

reinforcements
Welded to WebRight of
CopeBUTLeft BUT Welded to WebLeft of

BUTL2

Profile End Cuts

Sections
Supported
CopeBUTRight BUT Welded to WebRight of
BUTL2
CopeBulb B

Profile End Cuts

Sections
Supported
Cope_AngleRight UA
EA
CopeTopCornerSnipe BUT
BUTL2
EA
UA

Profile End Cuts

Sections
Supported
WebCut_C2Spline All
WebCut_C3RBulb B

Profile End Cuts

Sections
Supported
WebCut_C3Left BUT Welded to WebLeft of
BUTL2
WebCut_C3Right BUT Welded to WebRight of

BUTL2

Profile End Cuts

Sections
Supported
WebCutI_C3Left I Welded to WebLeft of
H
WebCutI_C3Right I Welded to WebRight of

H
End-to-end profiles
Sections
Supported
WebCut_OffsetInside All

Profile End Cuts

Sections
Supported
WebCut_OffsetOutside All
WebCut_C1AlligatorEnd All

Profile End Cuts
Lapped end cuts

Sections
Supported
SeamAngleCase1_2 EA Used for lapped end
cuts where the profile
UA laps its bounding
B object.
SeamAngleCase2_FB_2 FB Used for lapped end

cuts where the profile
laps its bounding
object.

Profile End Cuts

Sections
Supported
WebCut_Bend Plate All Used for manual profile
knuckle with either
Extend or Split and
Extend manufacturing
method.
Clip Web Cuts

Used when the assembly connection EndCutType is Clip.

Sections
Supported
Clip All Welded

Profile End Cuts
Cutback Web Cuts

Used when the assembly connection EndCutType is Cutback.
Name Cross-Sections Description Parameters

Supported
StraightSnip All
Snip Web Cuts

Used when the assembly connection EndCutType is Snip.

Supported
Snip All

Profile End Cuts

Supported
SnipWithFlange EA
UA
B
SnipNoNose All

Profile End Cuts

Supported
SnipRadius All
FreeEndWebCut FB
_F1_ER

Profile End Cuts

Supported
SnipBeyondBoun All
dary
Edge Reinforcement Web Cuts

Used only for flat-bar profile cross-sections used as Edge Reinforcements.

Supported
SM_WeldedER FB Edge reinforcement is center-
mounted on the edge of a parent
plate. The edge reinforcement
acts like the flange of a BUT, and
the parent plate acts like the web
of a BUT.

Profile End Cuts
Flange Cuts
Name Cross- Web Cut Parameters

Sections Type Used
Supported
FlangeCutSniped All Clip
Snip
FlangeCutSnipedAngle All Snip

Profile End Cuts

Sections Type Used
Supported
FlangeCutStraight All Welded
Bracketed
FlangeCutStraightAngle EA Welded
UA Bracketed
FlangeCutStraightBulb B Welded
Bracketed

Profile End Cuts

Sections Type Used
Supported
FlangeCutStraightACope EA Welded
(FlangeCut_W1) UA Bracketed
FlangeCutStraightCope All Welded

(FlangeCut_W4) Bracketed
FlangeCutStraightBCope B Welded
(FlangeCut_BW1) Bracketed

Profile End Cuts

Sections Type Used
Supported
FlangeCutBackAngle UA Welded
(FlangeCut_W1) EA Bracketed
Cutback
Snip
FlangeCutBackBUT BUT Welded

(FlangeCut_W4) BUTL2 Bracketed
Cutback
FlangeCutBackBulb B Welded
(FlangeCut_BW1) Bracketed
Cutback

Profile End Cuts

Sections Type Used
Supported
FlangeCutSnipWeld All Welded
Bracketed
Clip
FlangeCut_W4AlligatorEnd All Welded

FlangeCut_W4AlligatorPCEnd (end-to-end)
FlangeCut_BF1 Bulb (BPL) Used for all the

bulb cross
sections
(free end)

Profile End Cuts

Sections Type Used
Supported
FlangeCut_OffsetInside All Welded
FlangeCut_OffsetOutside (end-to-end)

SECTION 13
Member End Cuts

End cut symbols for members are delivered in the following locations:
 Web cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Web
Cuts\Members folder.
 Flange cuts are in the [Reference Data Folder]\SharedContent\Marine Library\Flange
Cuts\Members folder.
In This Section
Along-Axis Web Cuts for Members ................................................249
Along-Axis Flange Cuts for Members.............................................272
Web Cuts for Split Members ..........................................................301
Flange Cuts for Split Members .......................................................305
Mitered Web Cuts for Members .....................................................306
Mitered Flange Cuts for Members ..................................................307
Free-end Web Cuts for Members ...................................................308
Free-end Flange Cuts for Members ...............................................310

Member End Cuts
Along-Axis Web Cuts for Members

Creates a web cut for a member bounded by the axis curve of the bounding member.
There are separate web cuts for member assembly connections and generic assembly
connections.
Web-penetrated Center Cuts

Sections
Supported
Axis_Web_F All Valid boundaries and

orientations present only a
(member)
face to the bounding object.
Web_F
(generic)
Axis_WebTB_F All Valid boundaries and

(member)
face to the bounding
member. The bounding
member is an H-beam or
WebTB_F similar.
(generic)
Axis_Web_T_F All Valid boundaries and

(member)
member is a channel with
WebT_F the flanges up.
(generic)

Member End Cuts

Sections
Supported
Axis_WebB_F All Valid boundaries and

(member)
WebB_F the flange down.
(generic)
Axis_Web_ All Valid boundaries and

TE_F_BE orientations present a face,
a top edge, and a bottom
(member)
edge to the bounding
member.
Web_TE_F_BE
(generic)
Web_TE_F_BE_ Rolled Use for an exact fit when

Ellipse sections with both top and bottom
top and bounding edges have a
bottom fillet.
flanges
Valid boundaries and
orientations present a face,
member.

Member End Cuts

Sections
Supported
Web_TE_F_BE_ Rolled Use for an exact fit to the

EllipseTop sections with top edge only when it has a
top flange fillet.
member.
Web_TE_F_BE_ Rolled Use for an exact fit to the

Ellipse sections with bottom edge only when it
bottom flange has a fillet.
member.

F_BE orientations present a face
and a bottom edge to the
(member)
bounding member.
Web_F_BE
(generic)

Member End Cuts

Sections
Supported
Web_F_BE_ All Use for an exact fit to the

Ellipse bottom edge when it has a
fillet.
(generic)
orientations present a face
bounding member.

TE_F orientations present a face
and a top edge to the
(member)
bounding member.
Web_TE_F
(generic)
Web_TE_F_ All Use for an exact fit to the

Ellipse top edge when it has a fillet.
(generic) Valid boundaries and
orientations present a face
bounding member.

Member End Cuts

Sections
Supported
Axis_Web_TF_T_ All Valid boundaries and

E_F orientations present a face,
top edge, and top face to
(member)
the bounding member.
Web_TF_TE_F
(generic)

F_BE_BF orientations present a face,
bottom edge, and bottom
(member)
member.
Web_F_BE_BF
(generic)
Axis_Tube_00 Tube to Tube Tubular member is

bounded to another tubular
member (except on-
member configuration).

Member End Cuts

Sections
Supported
Axis_Web_Tube Standard Standard member is

member to bounded to tubular
Tube member: bounded
members web is cut by the
bounding member edge as
shown.
Web-penetrated Top Cuts

All web cuts are available for both member assembly connections and generic assembly
connections.

Sections
Supported
Inside Hook All Valid boundaries and

Flange Relief orientations present a
Top face and a top edge to
The bounding member is
still valid if it has a bottom
edge.

Member End Cuts

Sections
Supported

Snipe Top face and a top edge to
edge.
Square Flange All Valid boundaries and

Relief Top orientations present a
face and a top edge to
edge.

Member End Cuts

Sections
Supported

Relief Web Top orientations present a
Cut Snipe face and a top edge to
edge.
Square Along All Valid boundaries and

edge.

Member End Cuts

Sections
Supported

Web Top Cut face and a top edge to
Snipe the bounding member.
edge.
Edge Hook All Valid boundaries and

Outside Web face and a top edge to
Top the bounding member.
edge.

Member End Cuts

Sections
Supported

Outside Web face and a top edge to
Top Snipe the bounding member.
edge.
Top Snipe All Valid boundaries and

Outside orientations present a
edge.

Member End Cuts

Sections
Supported
Top Snipe All Valid boundaries and

Setback face and a top edge to
edge.
Outside Snipe All Valid boundaries and

Top Offset orientations do not
present a top edge to the
bounding member.

Member End Cuts

Sections
Supported
Snipe Face All All

Relief Top
Hook Face All All

Relief Top

Member End Cuts

Sections
Supported

Inside Web Top face and a bottom edge
to the bounding member.
still valid if it has a top
edge.
Top Outside All Valid boundaries and

Hook Flange orientations present a
Relief face and a bottom edge
edge.

Member End Cuts

Sections
Supported
Top Snipe Standard Standard member is

OutSide _Tube member to bounded to a tubular
Tube member. This web cut is
applicable to members
with a top flange such as
T, and also for members
without a top flange such
as L.
Web-penetrated Bottom Cuts

connections.

Sections
Supported

Bottom face and a bottom edge
to the bounding
member is still valid if it
has a top edge.

Member End Cuts

Sections
Supported

Snipe Bottom face and a bottom edge
to the bounding
has a top edge.

Relief Bottom orientations present a
face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported

Relief Web orientations present a
Bottom Cut face and a bottom edge
Snipe to the bounding
has a top edge.

to the bounding
has a top edge.

Member End Cuts

Sections
Supported

Web Bottom face and a bottom edge
Cut Snipe to the bounding
has a top edge.

Outside Web face and a bottom edge
Bottom to the bounding
has a top edge.

Member End Cuts

Sections
Supported

Outside Web face and a bottom edge
Bottom Snipe to the bounding
has a top edge.
Bottom Snipe All Valid boundaries and

to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Bottom Snipe All Valid boundaries and

Setback face and a bottom edge
to the bounding
has a top edge.
Outside Snipe All Valid boundaries and

Bottom Offset orientations present a
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Snipe Face All All

Relief Bottom
Hook Face All All

Relief Bottom

Member End Cuts

Sections
Supported

Inside Web face and a bottom edge
Bottom to the bounding
has a top edge.
Bottom All Valid boundaries and

Outside Hook orientations present a
Flange Relief face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Bottom Snipe Standard Standard member is

Outside_Tube member to bounded to a tubular
Tube member. This web cut is
applicable to members
with a bottom flange
such as L and also to
members without bottom
flange such as T.

Member End Cuts
Web Non-penetrated Cuts

connections.

Sections
Supported
Axis_Web_Straight All
(member)
FlushBoundedDepth
(generic)
Axis_Web_Flush All
(member)
FlushActual
(generic)
Axis_Web_Cope_Ext All Selected only when

BraceType =
(member)
"InsetMember"
and the cut is
between Brace and
Bounded of the
Parent Assembly
Connection (which
creates the Child
brace).

Member End Cuts
Along-Axis Flange Cuts for Members

Flange-penetrated Center Cuts
connections.

Sections
Supported
Axis_Flange_F All Valid boundaries and

(member)
face to the bounding object.
Flange_F
(generic)
Axis_ All Valid boundaries and

FlangeTB_F orientations present only a
(member)
member is an H-beam or
similar.
FlangeTB_F
(generic)

FlangeT_F orientations present only a
(member)
the flanges up.
FlangeT_F
(generic)

Member End Cuts

Sections
Supported

FlangeB_F orientations present only a
(member)
the flange down.
FlangeB_F
(generic)
Axis_Flange_ All Valid boundaries and

TE_F_BE orientations present a face,
(member)
member.
Flange_TE_F_
BE
(generic)

F_BE orientations present a face
(member)
bounding member.
Flange_F_BE
(generic)

Member End Cuts

Sections
Supported

TE_F orientations present a face
(member)
bounding member.
Flange_TE_F
(generic)

TF_TE_F orientations present a face,
top edge, and top face to the
(member)
bounding member.
Flange_TF_TE_
F
(generic)

F_BE_BF orientations present a face,
bottom edge, and bottom
(member)
member.
Flange_F_BE_
BF
(generic)

Member End Cuts

Sections
Supported
Axis Flange Standard Standard member is

_Tube member to bounded to a tubular
Tube member. The bounded
member's flange is cut by
the bounding member edge.
Axis_Flange_ All Selected only when

Variable_Bevel BraceType = InsetMember
and the cut is between
Brace and Bounded of the
Parent Assembly
Connection.

Member End Cuts
Flange-penetrated Top Cuts

connections.

Sections
Supported
Flg Inside Hook All Valid boundaries and

edge.

Snipe Top WL face and a top edge to
edge.

Member End Cuts

Sections
Supported

Snipe Top FL face and a top edge to
edge.
Flg Sqr Flange All Valid boundaries and

Relief Top orientations present a
edge.

Member End Cuts

Sections
Supported
Flg Sqr Flg Rlf All with no Valid boundaries and

Outside Snp left flange orientations present a
Top WL face and a top edge to
edge.
Flg Sqr Flg Rlf All with left Valid boundaries and
Outside Snp and right orientations present a
Top FL flanges face and a top edge to
edge.

Member End Cuts

Sections
Supported
Flg Sqr Alg All Valid boundaries and

edge.
Flg Sqr Alg Flg All with no Valid boundaries and

Rlf Outside left flange orientations present a
Snp Top WL face and a top edge to
edge.

Member End Cuts

Sections
Supported
Flg Sqr Alg Flg All with left Valid boundaries and
Rlf Outside and right orientations present a
Snp Top FL flanges face and a top edge to
edge.
Flg Edge Hook All Valid boundaries and

Flg Rlf OutSide orientations present a
edge.

Member End Cuts

Sections
Supported
Flg Edge Hook All with no Valid boundaries and

Flg Rlf OutSide left flange orientations present a
Snp Top WL face and a top edge to
edge.
Flg Edge Hook All with left Valid boundaries and

Flg Rlf OutSide and right orientations present a
Snp Top FL flanges face and a top edge to
edge.

Member End Cuts

Sections
Supported
Flg Top Snipe All with no Valid boundaries and

Outside WL left flange orientations present a
edge.
Flg Top Snipe All with left Valid boundaries and

Outside FL and right orientations present a
flanges face and a top edge to
edge.

Member End Cuts

Sections
Supported
Flg Top Snipe All with no Valid boundaries and

Outside left flange orientations present a
Setback WL face and a top edge to
edge.
Flg Top Snipe All with left Valid boundaries and

Outside and right orientations present a
Setback FL flanges face and a top edge to
edge.

Member End Cuts

Sections
Supported
Flg Outside All with no Valid boundaries and

Snipe Top left flange orientations do not
Offset WL present a top edge to the
bounding member.
Flg Outside All with left Valid boundaries and

Snipe Top and right orientations do not
Offset FL flanges present a top edge to the
bounding member.

Member End Cuts

Sections
Supported
Flg Snipe Face All All

Relief Top
Flg Hook Face All All

Relief Top

Member End Cuts

Sections
Supported

Inside Top face and a bottom edge
edge.
Flg Top All Valid boundaries and

Flange Relief face and a bottom edge
edge.

Member End Cuts

Sections
Supported
Flg Top Snipe Standard Standard member is

OutSide member to bounded to a tubular
_Tube_FL Tube member. The bounded
member's left side flange
is cut.
Flg Top Snipe Standard Standard member is

OutSide member to bounded to a tubular
_Tube_WL Tube member. In this case, no
left side flange exists for
the bounded member, so
the web-left is used as a
reference.

Member End Cuts
Flange-penetrated Bottom Cuts

connections.

Sections
Supported

to the bounding
has a top edge.

Snipe Bottom face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Flg Sqr Flange All Valid boundaries and

Relief Bottom orientations present a
to the bounding
has a top edge.
Flg Sqr Flg Rlf All with no left Valid boundaries and
Outside Snp flange orientations present a
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Flg Sqr Alg All Valid boundaries and

to the bounding
has a top edge.
Flg Sqr Alg Flg All with no left Valid boundaries and
Rlf Outside flange orientations present a
Snp Bottom face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported

Flg Rlf OutSide orientations present a
to the bounding
has a top edge.
Flg Edge Hook All with no left Valid boundaries and

Flg Rlf OutSide flange orientations present a
Snp Bottom face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Flg Bottom All with no left Valid boundaries and

Snipe Outside flange orientations present a
to the bounding
has a top edge.
Flg Bottom All with no left Valid boundaries and

Snipe Outside flange orientations present a
Setback face and a bottom edge
to the bounding
has a top edge.

Member End Cuts

Sections
Supported
Flg Outside All with no left Valid boundaries and

Snipe Bottom flange orientations do not
Offset present a top edge to
Flg Snipe Face All All

Relief Top

Member End Cuts

Sections
Supported
Flg Hook Face All All

Relief Top

Inside Bottom face and a top edge to
The bounding member
is still valid if it has a
bottom edge.

Member End Cuts

Sections
Supported
Flg Bottom All Valid boundaries and

Flange Relief face and a top edge to
The bounding member
is still valid if it has a
bottom edge.
FlgBottom Standard Standard member is

Snipe member to bounded to a tubular
OutSide_Tube_ Tube member. The right side
FR flange is cut as shown.

Member End Cuts
Flange Non-penetrated Cuts

connections.

Sections
Supported
Axis_Flange_Flush_LR All with left

and right
(member)
flanges
Straight_LR
(generic)
Axis_Flange_Flush_R All with no

left flange
(member)
Straight_R
(generic)
Axis_Flange_Straight_ All with left

Setback_LR and right
flanges
(member)
StraightSetback_LR
(generic)

Member End Cuts

Sections
Supported
Axis_Flange_Straight_ All with no

Setback_R left flange
(member)
StraightSetback_R
(generic)
Axis_Flange_Sniped_ All with left

Setback_LR and right
flanges
(member)
Sniped_Setback_LR
(generic)

Member End Cuts

Sections
Supported
Axis_Flange_Sniped_ All with no

Setback_R left flange
(member)
Sniped_Setback_R
(generic)
The following smart items are for cases in which the bounding member is a tube and
the bounded member is a standard member. These cases do not use the 8193 edge ID in the
symbol file.

Sections
Supported
Axis_Flange_Straight_ All with left

Setback_Tube_LR and right
flanges.
(member)

Member End Cuts

Sections
Supported
Axis_Flange_Straight_ All with no

Setback_Tube_R left flange.
(member)
Axis_Flange_Sniped_ All with left

Setback_Tube _LR and right
flanges.
(member)

Member End Cuts

Sections
Supported
Axis_Flange_Sniped_ All with no

Setback_Tube_R left flange.
(member)

Member End Cuts
Web Cuts for Split Members

Creates end-to-end web cuts for collinear members. End cuts are applied to both the bounded
and bounding members.
Different web cut shapes are possible by changing the answers to user-questions on the
Selection tab in the assembly connection Properties dialog box.

Sections
Supported
MbrSplitWeb_NoA All A web cut is placed

ngle perpendicular to the
member axis at the
seam location.
MbrSplitWeb_ All A web cut is placed at

AngleWebSqFl an offset towards
bounded and angular to
the member axis.
Flanges can have a
different seam angle.

AngleWebSqFl_2 an offset towards
bounding and angular
to the member axis.
Flanges can have a

Member End Cuts

Sections
Supported

AngleWebBevelFl an offset towards
the member axis.
Flanges have a seam
angle equal to that of
the web.

AngleWebBevelFl an offset towards
_2 bounding and angular
to the member axis on
bounded. Flanges have
a seam angle equal to
that of the web.

AngleWebAngleFl an offset towards
the member axis.
Flanges can have a
The cutting plane is
inclined to the member
axis, and the angle of
the inclination can be
changed using the
cutVang parameter.

Member End Cuts

Sections
Supported

AngleWebAngleFl an offset towards
_2 bounding and angular
to the member axis.
Flanges can have a
The cutting plane is
inclined to the member
axis, and the angle of
the inclination can be
changed using the
cutVang parameter.

DistWebDistFl an offset towards
bounded, and slope is
controlled through
offsets at top and
bottom points of the
seam.

DistWebDistFl_2 an offset towards
bounding, and the
slope is controlled
through offsets at top
and bottom points of
the seam.

Member End Cuts

Sections
Supported

OffsetWebOffsetFl an offset and angular to
the member axis on
bounded. The web, top,
and bottom flanges can
have different offsets
from the original seam.

OffsetWebOffsetFl an offset and angular to
_2 the member axis on
bounded. The web, top,
and bottom flanges can
have different offsets
from the original seam.

Member End Cuts

Sections
Supported
MbrSplitWeb_Tub Circular A cut is placed at the

e sections seam location.
Flange Cuts for Split Members

Placed on flanges of members connected end to end and collinear.
A flange cut is placed only when the answer for SplitEndToEndCase is NoAngle.

Sections
Supported
MbrEndFlg_Straight All with left and Places a

_LR right flanges. straight cut.
MbrEndFlg_Straight All with no left Places a

_R flange. straight cut.

Member End Cuts
Mitered Web Cuts for Members

Sections
Supported
MbrMiterWeb All Places a miter straight

end cut.
MbrMiterWeb_S All Places a straight center

S cut and a sniped cut at
top and bottom so that
the flanges of bounding
and bounded do not
meet.
MbrMiterWeb_S All Places a straight cut and

B a sniped cut at bottom
so that the bottom
flanges of bounding and
bounded do not meet.

Member End Cuts

Sections
Supported
MbrMiterWeb_S All Places a straight cut and

T a sniped cut at top so
that the top flanges of
bounding and bounded
do not meet.
MbrMiterWeb_T Circular Places a miter cut for

ube sections circular cross-sections.
Mitered Flange Cuts for Members

Sections
Supported
MbrEndFlg_ All with left Places a miter cut on

StraightSetback_L and right the flange.
R flanges.

Member End Cuts

Sections
Supported
MbrEndFlg_ All with no left Places a miter sloped

StraightSetback_ flange. cut on the flange.
R
Free-end Web Cuts for Members

These web cuts are placed at the end of an unsupported member.

Sections
Supported
MbrWeb_FreeSnipeT All Places a sniped

op web cut with slope
inward at the top of
the flange.

Member End Cuts

Sections
Supported
MbrWeb_ All Places a sniped

FreeSnipeBottom web cut with slope
inward at the
bottom of the
flange.
MbrWeb_FreeAngled All Use when

Cut EndcutType is
Welded in the
assembly
connection
Properties dialog
box.
Places a sniped
web cut. The
cutting plane
direction is inclined
towards the
member axis.
MbrTube_FreeEndCu Circular Places a sniped

t sections end cut for tubes.
The sketching
plane can be
rotated.

Member End Cuts
Free-end Flange Cuts for Members

These web cuts are placed at the end of an unsupported member.

Sections
Supported
MbrFree_Flange_ All with left Places a straight flange

Straight_LR and right cut.
flanges
MbrFree_Flange_ All with no left Places a straight flange

Straight_R flange cut.

Member End Cuts

Sections
Supported
MbrFree_Flange_ All with left Places a sniped flange

Sniped_LR and right cut.
flanges
MbrFree_Flange_ All with no left Places a sniped flange

Sniped_R flange cut.

SECTION 14
Slots
Slot (also called penetration) symbols are delivered in the [Reference Data
Folder]\SharedContent\MarineLibrary\Penetrations and [Reference Data
Folder]\SharedContent\Penetrations folders.
In This Section
Slot A ............................................................................................. 312
Slot C ............................................................................................. 314
Slot C2 ........................................................................................... 325
Slot I ............................................................................................... 326
Slot A
Slot A class penetrations are not connected to their cross-sections.
Name Cross-Sections Selection Logic Parameters

Supported in the Rules
SlotAA_SM EA None
UA

Slots

SlotBA_SM B None
SlotFA_SM FB None

Slots

SlotTA_SM T None
BUT
BUTL2
Slot C
Slot C class penetrations are connected to their cross-sections.
Web Left Connection

Name Cross- Selection Logic Parameters
Sections in the Rules
Supported
SlotAC_L_AAT_DTR EA Non-tight
UA Profile height >
125 mm

Slots

Supported
SlotAC_L_PAT_DTR EA Non-tight
UA
SlotAC_L_PAT_STR EA Tight
UA

Slots

Supported
SlotBC_L_AAT_DTR B Non-tight
SlotBC_L_LAT_STR B Non-tight
Profile height 
120 mm
SlotBC_L_LTT_STR B Tight

Slots

Supported
SlotBC_L_PAT_DTR B Non-tight
SlotBC_L_PAT_STR B Tight

Slots

Supported
SlotFC_L_AAT_DTR FB Non-tight
SlotFC_L_PAT_DTR FB Non-tight

Slots

Supported
SlotFC_L_PAT_STR FB Tight
SlotL2C_L_AAT_DTR BUTL2 Non-tight

Profile height >
150 mm

Slots

Supported
SlotL2C_L_PAT_DTR BUTL2 Non-tight
SlotL2C_L_PAT_DTR2 BUTL2 Tight

Slots

Supported
SlotTC_L_AAT_DTR BUT Non-tight

Profile height >
150 mm
SlotTC_L_PAT_DTR BUT Non-tight

Slots

Supported
SlotTC_L_PAT_STR BUT Tight
Top Connection
Supported
SlotTC_T_PAA_STR BUT Non-tight

Slots
Web Left and Top Connection

Supported
SlotAC_LT_AAA EA Non-tight
UA
SlotAC_LT_PAA EA Non-tight
UA

Slots

Supported
SlotAC_LT_PAT EA Tight
SlotAC_LT_PAT2 UA
(all use SlotAC_LT_PAT)
SlotBC_LT_PAT B Tight
SlotBC_LT_PAT2
(all use SlotBC_LT_PAT)

Slots

Supported
SlotFC_LT_PAT FB Tight
SlotFC_LT_PAT2
(all use SlotBC_LT_PAT)
Slot C2
Slot C2 class penetrations are connected to the top of the flange of their cross-sections.

Supported
SlotL2C2_T_PTT_STR BUT Tight

SlotL2C2_T_PTT_STR2 BUTL2
SlotTC2_T_PTT_STR
SlotTC2_T_PTT_STR2
(all use
SlotTC2_T_PTT_STR)

Slots
Slot I
Slot I class penetrations are connected to the left and right sides of the web of their cross-
sections.
Web Left and Web Right Connection

Supported
SlotAI EA Available in
catalog, but not
available in
current selection
of SML Slot
rules.
SlotAI_LR_PAAP_STR EA Tight
UA

Slots

Supported
SlotAI_LR_AAAA_STR EA Non-tight
UA Profile height >
125 mm
SlotBI_LR_PAAP_STR B Tight

Slots

Supported
SlotBI_LR_AAAA_STR B Non-tight
SlotFI Available in
catalog, but not
available in
current selection
of SML Slot
rules.
SlotFI_LR_PAAP_STR FB Tight

Slots

Supported
SlotFI_LR_AAAA_STR FB Non-tight
SlotL2I_LR_PAAP_STR BUTL2 Tight

Slots

Supported
SlotL2I_LR_AAAA_STR BUTL2 Non-tight
SlotTI_LR_PAAP_STR BUT Tight

Slots

Supported
SlotTI_LR_AAAA_STR BUT Non-tight
Web Left, Web Right, Connection and Top Connection

Supported
SlotAI_LTR_PAAP_STR EA Tight
UA
SlotBI_LTR_PAAP_STR B Tight

Slots

Supported
SlotFI_LTR_PAAP_STR FB Tight
SlotL2I_LTR_PAAP_STR BUTL2 Tight
SlotTI_LTR_PAAP_STR BUT Tight

SECTION 15
Sketched Features
The sketched feature symbols are delivered with the software in the [Reference Data
Folder]\SharedContent\Sketched Features folder.
Obround Feature Has no smart rule to

select.
Available when placing
an opening/Sketched
feature.
Oval Feature Has no smart rule to

select.
an opening/Sketched
feature.
Rectangle Feature Has no smart rule to

select.
an opening/Sketched
feature.

Sketched Features
Round Feature Has no smart rule to

select.
an opening/Sketched
feature.
Square Feature Has no smart rule to

select.
an opening/Sketched
feature.

SECTION 16
Openings
The opening symbols are delivered with the software in the [Reference Data Product
Directory]\SharedContent\Openings folder. You can create your own custom opening symbols
using the 2D Symbols utility that is delivered with the software.
In This Section
CircleOpening ................................................................................ 335
OvalOpening .................................................................................. 336
RectangleOpening ......................................................................... 336
SketchOpening .............................................................................. 336
SquareOpening.............................................................................. 337
TriangleOpening ............................................................................ 337
CircleOpening

Openings
OvalOpening
RectangleOpening
SketchOpening

Openings
SquareOpening
TriangleOpening

SECTION 17
Structural Manufacturing
The structural manufacturing symbols are delivered with the software in the [Reference Data
Product Directory]\SharedContent\StructManufacturing folder. You can create your own custom
symbols using the 2D Symbols utility that is delivered with the software.
In This Section
Manufacturing Requirements for Profile Cross Sections............... 339
Manufacturing Requirements for Member Cross Sections............ 340
Bevel .............................................................................................. 341
Bevel1 (I-Type) .............................................................................. 341
Bevel2 (V-Type) ............................................................................. 342
Bevel3 (V-Type) ............................................................................. 342
Bevel4 (X-Type) ............................................................................. 342
Bevel5 (Y-Type) ............................................................................. 342
Bevel6 (X-Type with Chamfer) ...................................................... 342
Bevel10 .......................................................................................... 343
BevelA ........................................................................................... 344
BevelB ........................................................................................... 344
BevelParam ................................................................................... 345
FeatureTab1 .................................................................................. 345
Grind .............................................................................................. 345
Knuckle .......................................................................................... 346
Margin ............................................................................................ 346
PartCenterLL ................................................................................. 346
PartDirC ......................................................................................... 347
PartDirCL ....................................................................................... 347
PartDirCR ...................................................................................... 347
PartDirL .......................................................................................... 348
PartDirLL ........................................................................................ 348
PartDirLLFlangeRR ....................................................................... 348
PartDirR ......................................................................................... 349
PartDirRR ...................................................................................... 349
PartDirRRFlangeLL ....................................................................... 349
PMFeature ..................................................................................... 350
Shrinkage ....................................................................................... 350
SMPlateTab ................................................................................... 350
UnSpecBevel ................................................................................. 351
WeldTab1 ...................................................................................... 351

Manufacturing Requirements for Profile Cross

Sections
All profile cross sections must support the IJUAXSectionMfgProperties and
IJUAXSectionMatlProperties virtual interfaces.
IJUAXSectionMatlProperties …
ShearCenterLoc_X
ShearCenterLoc_Y
CentroidLoc_X
CentroidLoc_Y
IJUAXSectionMfgProperties OriginKeyPoint
XDirectionKeyPoint
YDirectionKeyPoint
The Shear Center is the point at which a shear force can act without producing any twist in the
section. The centroid of a cross section shape is the arithmetic mean (average) position of all
the points in the shape.
Shear Center and Centroid are both required properties to unfold a profile part in Structural
Manufacturing. Shear Center gives the axis information about which the profile is untwisted. The
Centroid gives the axis about which the profile is unbent.
OriginKeyPoint, XDirectionKeyPoint and YDirectionKeyPoint values are used only in Structural
Manufacturing to interpret the location of Centroid and Shear Center. Centroid and Shear Center
locations should be given correctly relative to these key points.
The following example shows how to define a cross section centroid with respect to key points
defined in Cross Section work sheet:

Any of the following rows are correct for the previous figure:
OriginKeyPoint XDirectionKeyPoint YDirectionKeyPoint Centroid_X Centroid_Y
1 23 13 15 75
13 15 1 15 25
23 15 1 75 35
Manufacturing Requirements for Member Cross

Sections
All member cross sections must have CrossSectionType information.
Valid Cross Section Type strings:
 BulbFlat
 Channel
 FlatBar
 IBar
 TeeBar
 EqualAngle
 UnequalAngle
 RectangleTube
 SquareTube
 RoundTube
 RoundBar
 SquareBar
 HalfRound.

Member cross sections are not required to support IJUAXSectionMfgProperties or

IJUAXSectionMatlProperties virtual interfaces.
Cardinal Point 10 must be defined in the member cross section symbol at the centroid location.
Cardinal Point 15 must be defined at the Shear Center location.
If the member has a flange, it must support the IStructFlangedSectionDimensions virtual
interface with the following properties:
 d = Web Depth
 tw = Web Thickness
 tf = Flange Thickness
 bf = Flange Width
If the member, such as round tubes, rectangular tubes, Half Round, and so on, does not have a
flange, it must support the IStructCrossSectionDimensions virtual interface.
 Depth = Web Depth
 tdes = Thickness
OR
 tnom = Thickness
This property is read-only if the tdes property does not exist.
Bevel
See Also
Structural Manufacturing (on page 338)
Bevel1 (I-Type)

Bevel2 (V-Type)
Bevel3 (V-Type)
Bevel4 (X-Type)
Bevel5 (Y-Type)
Bevel6 (X-Type with Chamfer)

Bevel10

BevelA
See Also
BevelB
See Also

BevelParam
FeatureTab1
See Also
Grind
See Also

Knuckle
See Also
Margin
See Also
PartCenterLL

PartDirC
PartDirCL
PartDirCR

PartDirL
See Also
PartDirLL
See Also
PartDirLLFlangeRR

PartDirR
See Also
PartDirRR
See Also
PartDirRRFlangeLL
See Also

PMFeature
Shrinkage
SMPlateTab
See Also

UnSpecBevel
WeldTab1

Index
2 C
2D Symbols Reference Data • 9 Chamfers • 49
2S Brackets • 11 CircleOpening • 335
2S Flanged Brackets • 45 Clip Web Cuts • 237
Collars and Clips • 51
3 Corner Features for Members • 71
Corner Features for Plates and Stiffeners •
3S Flanged Brackets • 46 65
3S Lapped S1 Brackets • 21 Cross Section Symbol 2L • 81
3S Lapped S1S2 Brackets • 26 Cross Section Symbol B • 189
3S Lapped S1S2S3 Brackets • 32 Cross Section Symbol BUBoxFM • 84
3S Lapped S1S3 Brackets • 33 Cross Section Symbol BUC • 87
3S Lapped S2 Brackets • 35 Cross Section Symbol BUCan • 90
3S Lapped S2S3 Brackets • 40 Cross Section Symbol BUCone • 93
3S Lapped S3 Brackets • 42 Cross Section Symbol BUEndCan • 95
3S Trimmed Brackets • 16 Cross Section Symbol BUFlat • 98
Cross Section Symbol BUI • 100
4 Cross Section Symbol BUIHaunch • 102
4S Brackets • 43 Cross Section Symbol BUITaperWeb • 105
Cross Section Symbol BUIUE • 108
Cross Section Symbol BUL • 111
5 Cross Section Symbol BUL2 • 190
5S Brackets • 44 Cross Section Symbol BUL3 • 192
Cross Section Symbol BUT • 114, 195
A Cross Section Symbol BUTube • 116
Along-Axis Flange Cuts for Members • 272 Cross Section Symbol C (MC) • 119
Along-Axis Web Cuts for Members • 249 Cross Section Symbol C_SS • 196
Cross Section Symbol C_SType • 198
Cross Section Symbol CS • 122
B Cross Section Symbol EA • 200
Bevel • 341 Cross Section Symbol FB • 202
Bevel1 (I-Type) • 341 Cross Section Symbol HalfR • 205
Bevel10 • 343 Cross Section Symbol HSSC (Pipe) • 123
Bevel2 (V-Type) • 342 Cross Section Symbol HSSCs • 125
Bevel3 (V-Type) • 342 Cross Section Symbol HSSR • 128
Bevel4 (X-Type) • 342 Cross Section Symbol HSSRs • 130
Bevel5 (Y-Type) • 342 Cross Section Symbol HW • 133, 169
Bevel6 (X-Type with Chamfer) • 342 Cross Section Symbol HWWF • 135, 171
Bevel7 (X-Type with Chamfer) • 343 Cross Section Symbol I • 207
Bevel8 (X-Type with Chamfer) • 343 Cross Section Symbol I_SType • 209
Bevel9 (X-Type with Chamfer) • 343 Cross Section Symbol L • 137
BevelA • 344 Cross Section Symbol P • 211
BevelB • 344 Cross Section Symbol R • 213
BevelParam • 345 Cross Section Symbol Rect • 141, 173
Bracket Symbols • 10 Cross Section Symbol RectC • 143, 176
Cross Section Symbol RectCWF • 145, 178
Cross Section Symbol RectWF • 148, 181

Index
Cross Section Symbol RS • 150 Mitered Web Cuts for Members • 306
Cross Section Symbol S • 152
Cross Section Symbol SB • 215 N
Cross Section Symbol SqTu • 217
Cross Section Symbol ST • 155 Non-Tight Clips • 51
Cross Section Symbol T • 218
Cross Section Symbol T (MT) • 157 O
Cross Section Symbol T_SType • 218 Openings • 335
Cross Section Symbol UA • 220 OvalOpening • 336
Cross Section Symbol W (M) • 160
Cross Section Symbol Wedge • 163, 183
Cross Section Symbol WedgeWF • 165,
P
185 PartCenterLL • 346
Cutback Web Cuts • 238 PartDirC • 347
PartDirCL • 347
PartDirCR • 347
D PartDirL • 348
Double Sided Chamfer • 49 PartDirLL • 348
PartDirLLFlangeRR • 348
E PartDirR • 349
Edge Features • 223 PartDirRR • 349
Edge Reinforcement Web Cuts • 241 PartDirRRFlangeLL • 349
PMFeature • 350
Preface • 8
F Profile Cross Sections • 188
FeatureTab1 • 345 Profile End Cuts • 228
Flange Contours for Brackets • 48
Flange Cuts • 242 R
Flange Cuts for Split Members • 305
Flange Non-penetrated Cuts • 296 RectangleOpening • 336
Flange-penetrated Bottom Cuts • 288
Flange-penetrated Center Cuts • 272 S
Flange-penetrated Top Cuts • 276 Shrinkage • 350
Free-end Flange Cuts for Members • 310 Single Sided Chamfers • 49
Free-end Web Cuts for Members • 308 Sketched Features • 333
SketchOpening • 336
G Slot A • 312
Grind • 345 Slot C • 314
Slot C2 • 325
Slot I • 326
K Slots • 312
Knuckle • 346 SMPlateTab • 350
Snip Web Cuts • 238
M SquareOpening • 337
Standard Bracket Flange Contour • 48
Manufacturing Requirements for Member Structural Manufacturing • 338
Cross Sections • 340
Manufacturing Requirements for Profile
Cross Sections • 339 T
Margin • 346 Tight Collars • 55
Member Cross Sections • 80 TriangleOpening • 337
Member End Cuts • 248
Mitered Flange Cuts for Members • 307

Index
U
UnSpecBevel • 351
W
Wall Cross Sections • 168
Web Cuts for Split Members • 301
Web Non-penetrated Cuts • 271
Web-penetrated Bottom Cuts • 262
Web-penetrated Center Cuts • 249
Web-penetrated Top Cuts • 254
Welded Web Cuts • 228
WeldTab1 • 351
What's New in 2D Symbols Reference Data
•8

2D Symbols: Reference Data Guide

Uploaded by

Copyright:

Available Formats

2D Symbols: Reference Data Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2D Symbols: Reference Data Guide

Uploaded by

Copyright:

Available Formats

2D Symbols

Reference Data Guide

Version 2016 (11.0)

U.S. Government Restricted Rights Legend

2D Symbols Reference Data Guide 2

2D Symbols Reference Data Guide 3

What's New in 2D Symbols Reference Data ............................................................................................. 8

2D Symbols Reference Data ....................................................................................................................... 9

Bracket Symbols ....................................................................................................................................... 10

Flange Contours for Brackets .................................................................................................................. 48

Collars and Clips ....................................................................................................................................... 51

Corner Features for Plates and Stiffeners .............................................................................................. 65

Corner Features for Members .................................................................................................................. 71

Member Cross Sections............................................................................................................................ 80

2D Symbols Reference Data Guide 4

Cross Section Symbol BUFlat............................................................................................................... 98

Wall Cross Sections ................................................................................................................................ 168

Profile Cross Sections ............................................................................................................................ 188

2D Symbols Reference Data Guide 5

Cross Section Symbol I ....................................................................................................................... 207

Edge Features .......................................................................................................................................... 223

Profile End Cuts ....................................................................................................................................... 228

Member End Cuts .................................................................................................................................... 248

Slots .......................................................................................................................................................... 312

Sketched Features................................................................................................................................... 333

Openings .................................................................................................................................................. 335

2D Symbols Reference Data Guide 6

OvalOpening ....................................................................................................................................... 336

Structural Manufacturing ........................................................................................................................ 338

Index ......................................................................................................................................................... 352

2D Symbols Reference Data Guide 7

What's New in 2D Symbols Reference Data

2D Symbols Reference Data Guide 8

2D Symbols Reference Data

2D Symbols Reference Data Guide 9

2D Symbols Reference Data Guide 10

Name Description Parameters

2SBracketLinear Linear free edge

2SLT_wScallop Linear free edge

2SLL_1Lap Linear free edge

2D Symbols Reference Data Guide 11

Name Description Parameters

2SLL_1Lap_wScallop Linear free edge

2SLL_2Lap Linear free edge

2SLL_2Lap_wScallop Linear free edge

2D Symbols Reference Data Guide 12

Name Description Parameters

2SCT Curved free edge

2SCT_wScallop Curved free edge

2SCL_1Lap Curved free edge

2SCL_1Lap_wScallop Curved free edge

2D Symbols Reference Data Guide 13

Name Description Parameters

2SCL_2Lap Curved free edge

2SCL_2Lap_wScallop Curved free edge

2D Symbols Reference Data Guide 14

The following 2S bracket symbols are delivered in the [Reference Data

2D Symbols Reference Data Guide 15

Offset from Support 1