Saturated Surface-Dry Specific Gravity and Absorption of Aggregates
Saturated Surface-Dry Specific Gravity and Absorption of Aggregates
Saturated Surface-Dry Specific Gravity and Absorption of Aggregates
1. SCOPE
1.1 This method determines the saturated surface-dry (SSD) specific gravity and water
absorption of natural mineral aggregates used in Portland cement concrete.
1.2 The values given in parentheses (if provided) are not standard and may not be exact
mathematical conversions. Use each system of units separately. Combining values from
the two systems may result in nonconformance with the standard.
2. DEFINITIONS
2.1 Bulk volume (of an aggregate)—the volume of water displaced by aggregate in a SSD
condition, including both the volume of the impermeable portion of the aggregate
particles and the volume of the permeable voids in the particles.
2.2 Saturated surface-dry—the condition of the aggregate when all permeable pores of each
particle are completely saturated with water and its surface has no free moisture.
2.3 Saturated surface-dry specific gravity—the ratio of the mass of SSD aggregate to the
mass of an equal volume of water.
3. REPORT FORMS
4. APPARATUS
4.3 Sample container, wire basket of 3.35 mm (No. 6) or finer mesh, or a bucket of
approximately equal breadth and height, with a capacity of 4–7 L (1–1-3/4 gal.) for
38 mm (1-1/2 in.) nominal maximum size or smaller, and a larger container as needed for
testing larger maximum size aggregate. The container should be constructed to prevent
trapping air when the container is submerged (optional).
4.4 Water tank, into which the sample and container are placed for complete immersion
while suspended below the balance, equipped with an overflow outlet for maintaining a
constant water level (optional).
4.5 Suspended apparatus, wire suspending the container should be the smallest practical size
to minimize any possible effects of a variable immersed length (optional).
4.8 Set of standard U.S. sieves, meeting requirements of Tex-907-K, in the following sizes:
4.75 mm (No. 4)
600 m (No. 30).
5. MATERIALS
6. PROCEDURES
6.1.1 Select a 2 L (0.5 gal.) mason jar with good threads on the neck.
6.1.3 If the rim is rough, place a piece of fine grain Carborundum cloth on a smooth, solid,
level surface; hold the jar in a vertical position with the top against the Carborundum
cloth; and smooth and true the rim by rotating the jar over the cloth.
6.1.4 Apply force and continue the grinding action until the rim of the jar appears to be
perfectly smooth.
6.1.5 Clean the jar and fill with clean tap water at 23 2C (73 3F).
6.1.6 With the gasket seated smoothly in place to prevent leaking, screw the metal pycnometer
cap snugly on the jar.
6.1.7 Use the rubber siphon bulb to fill with water, leaving a rounded bead of water on top of
the cap.
6.1.8 Dry the outside of the cap and jar with a towel.
6.1.9 Determine the mass of the pycnometer filled with water to the nearest 0.5 g and record
the mass as Y under Section 7.
6.2.1 Secure a representative field sample of the fine aggregate passing a 4.75 (No. 4) sieve in
accordance with Tex-400-A. Use a sample splitter or quartering cloth to reduce the
sample to a laboratory test size of approximately 3000 g.
6.2.2 Place the test sample into a pan and cover with water. Allow to soak for a minimum of
24 hours. Avoid using metal pans, which react with aggregates.
Note 3—For field determination of absorption only, use Tex-409-A, Part II.
6.2.3 Decant the water and spread the material in a thin layer on a clean, smooth surface such
as a metal-topped workbench.
6.2.4 Allow the sample to air dry without applying artificial heat.
6.2.5 Use a small trowel to stir and mix the sample frequently so that the particles on top will
not become drier than SSD.
6.2.6 Hold the cone firmly on a smooth nonabsorbent surface with the larger diameter down.
6.2.7 Place the partially dried fine aggregate loosely in the cone.
6.2.8 Fill it to slightly overflowing by holding the mold with a cupped hand.
6.2.9 Lightly tamp the fine aggregate into the mold with 25 light drops of the tamper. Start
each drop at about 5 mm (0.2 in.) above the top surface of the fine aggregate.
6.2.10 Allow the tamper to fall freely and distribute the drops over the entire surface.
6.2.11 Remove loose sand from around the base and lift the cone vertically.
6.2.11.1 If surface moisture is still present, the fine aggregates will retain the molded shape.
6.2.11.2 Some angular fine aggregate or material with high proportion of fines may not slump in
the cone test upon reaching a surface-dry condition. This may be the case if fines become
airborne upon dropping a handful of sand from the cone test 100–150 mm (4–6 in.) onto
a surface. For these materials, consider the SSD condition as the point that one side of the
fine aggregate slumps slightly upon removing the mold.
6.2.12 Transfer the SSD test sample to the balance and weigh out approximately 1200 g
immediately to prevent loss of moisture.
6.2.14 Place the SSD sample into the pycnometer jar about one quarter full of water by means of
the wide-mouthed funnel, taking care not to lose any of the material.
6.2.15 Rinse the funnel over the jar with water so that any clinging particles will wash into the
jar.
6.2.16 Fill the jar with water to within about 12.5 mm (0.5 in.) of the rim, screw the cap on the
jar, and then fill completely with water.
6.2.17 Stop the hole in the cap with a finger and roll the pycnometer to free all entrapped air.
When the sample contains large pieces of coarse aggregate, roll the pycnometer gently to
prevent breaking the glass jar. Raise and lower the jar in such a manner that the material
will flow from one end of the jar to the other while it is being rolled.
6.2.18 When a quantity of air bubbles has accumulated, refill the pycnometer, washing out the
air, and roll again.
6.2.19 Repeat the rolling and shaking of the jar until all of the air has been removed. To
facilitate the removal of the air, use a water aspirator, but take care to prevent siphoning
out any of the finer particles.
6.2.21 Use a syringe or rubber bulb to fill the jar carefully with water, leaving a rounded bead of
water on top of the cap.
6.2.22 Determine the mass of the pycnometer and contents to the nearest 0.5 g.
6.2.23 Record the mass, Z, and the temperature of the water as shown under Section 7.
6.2.24 Remove the pycnometer cap and pour the sample into a clean, tared pan.
6.2.25 Rinse the cap, jar, and hands thoroughly over the pan to collect all of the material.
6.2.26 Allow the material to settle and the water to become clear, then decant or siphon the
water from the sample.
6.2.27 Dry the aggregate to constant mass in an oven, then cool to room temperature and weigh.
6.2.28 Record the net oven-dry mass of the sample to the nearest 0.5 g as X1 under Section 7.
6.2.29 Keep the excess saturated surface-dry material sealed in the airtight container for check
tests. When making check determinations, use an odd number of grams, approximately
the same mass as for the first test, for mass of surface-dry aggregate.
6.3.1 Secure a representative field sample in accordance with Tex-400-A and reduce to
laboratory test size of approximately 1500 g with a sample splitter or quartering cloth.
6.3.2 Place the sample in a pan and cover with water. Allow to soak for a minimum of
24 hours. Avoid using metal pans, which react with aggregates.
Note 4—For field determination of absorption only, use Tex-409-A, Part II.
6.3.3 Drain the water from the sample and transfer a portion of the material to a lint-free cloth
or towel.
6.3.4 Roll the material in the cloth and rub with dry ends until all surface moisture has been
removed. The material may also air dry at room temperature to SSD. Do not dry past the
SSD condition.
6.3.5 When SSD is reached, place the surface-dried material into a small container and cover
with a lid.
6.3.7 Transfer the SSD test sample to the balance and weigh immediately to prevent loss of
moisture.
6.3.8 Place sample into pycnometer jar about one quarter full of water using the wide-mouthed
funnel, taking care not to lose any of the material.
6.3.9 Rinse the funnel so that any clinging particles wash into the jar.
6.3.10 Fill the jar with water to within about 12.5 mm (0.5 in.) of the rim, screw the cap on the
jar, and then fill completely with water.
6.3.11 Stop the hole in the cap with finger and roll the pycnometer to free all entrapped air. If
the sample contains large pieces of coarse aggregate, roll the pycnometer gently to
prevent breaking the glass jar. Raise and lower the jar so the material will flow from one
end of the jar to the other while being rolled.
6.3.12 When a quantity of air bubbles has accumulated, refill the pycnometer, washing out the
air, and roll again. Repeat the rolling and shaking of the jar until all of the air has been
removed. To facilitate the removal of the air, a water aspirator may be used, but take care
to prevent siphoning out any of the finer particles.
6.3.14 Carefully fill the jar with water using a syringe or rubber bulb, leaving a rounded bead of
water on the top of the cap.
6.3.15 Determine the mass of the pycnometer and contents to the nearest 0.5 g.
6.3.16 Record the mass, Z, and the temperature of the water as shown in Section 7.
6.3.17 Remove pycnometer cap and pour sample into a clean, tared pan.
6.3.18 Rinse cap, jar, and hands thoroughly over the pan to collect all of the material.
6.3.19 Allow material to settle and water to become clear, then decant or siphon the water from
the sample.
6.3.20 Dry the aggregate to constant mass in an oven, then cool to room temperature and weigh.
6.3.21 Record net oven-dry mass of sample to the nearest 0.5 g as X1 under Section 7.
6.3.22 Keep the excess saturated surface-dry material sealed in the airtight container for check
tests. When making check determinations, use an odd number of grams, approximately
the same mass as for the first test, for mass of surface-dry aggregate.
6.4.1 Determine the specific gravity of the mineral filler in accordance with Tex-202-F, using
material that passes the 600 m (No. 30) sieve.
6.5.1 Secure a representative field sample in accordance with Tex-400-A. Reduce to laboratory
test size with a sample splitter or quartering cloth according to Table 1.
6.5.2 Reject all material passing a 4.75 mm (No. 4) sieve by dry sieving and thoroughly
washing to remove dust or other coatings from the surface.
6.5.3 Place the sample in a pan and cover with water. Allow to soak for a minimum of
24 hours. Avoid using metal pans, which react with aggregates.
Note 6—For field determination of absorption only, use Tex-409-A, Part II.
6.5.4 Remove the test sample from the water and roll it in a large absorbent cloth until all
visible films of water are removed.
6.5.4.1 Wipe the larger particles individually. Use a moving stream of air to assist in the drying
operation. Take care to avoid evaporation of water from aggregate pores during the
operation of surface drying.
6.5.4.2 Determine the mass of the test sample in the saturated surface-dry condition.
6.5.4.3 Record this and all subsequent masses to the nearest 1 g or 0.1 percent of the sample
mass, whichever is greater.
6.5.5 After determining the mass, immediately place the saturated-surface-dry test sample in
the sample container and determine the mass in water at 23.0 ± 1.7°C (73.4 ± 3°F),
having a density of 997 ± 2 kg/m3. Take care to remove all entrapped air before
determining the mass by shaking the container while immersed.
6.5.7 Dry the test sample to constant mass at a temperature of 110 ± 5°C (230 ± 9°F). Cool in
air at room temperature 1–3 hours, or until the aggregate has cooled to a temperature that
is comfortable to handle (approximately 50°C). Determine the mass and record as X1
under Section 7.
7. CALCULATIONS
G X / ( X Y Z ) or X / (X S)
-OR-
GBULK X 1 / ( X Y Z ) or X1 / ( X S )
Where:
S = submerged sample weight, in basket
X = mass of SSD sample, kg (lb.)
X1 = the net oven-dry mass of the sample, kg (lb.)
Y = mass of calibrated pycnometer filled with water, kg (lb.)
Z = mass of pycnometer containing SSD sample and water at 23 2C (73 3F) to fill,
kg (lb.)
7.2 For a combination of aggregates, calculate G for each (G1, G2, Gi, etc.) and then calculate
the average SSD specific gravity of the combination:
G 100 / [( W1 / G1 ) ( W2 / G2 ) ( Wi / Gi ) etc. ]
Where:
W1 = percentage of ith material based on the total mass of the combination.
A ( X X1 ) / X1
A [( A1 W1 ) ( A2 W2 ) etc. ] / 100
8. REPORT
8.1 Report specific gravity results to the nearest 0.01 and absorption results to the nearest
0.1%.