Celex:02007l0046 20180118:en:txt PDF

02007L0046 — EN — 18.01.2018 — 021.
001 — 1
This text is meant purely as a documentation tool and has no legal effect. The Union's institutions do not assume any liability
for its contents. The authentic versions of the relevant acts, including their preambles, are those published in the Official
Journal of the European Union and available in EUR-Lex. Those official texts are directly accessible through the links
embedded in this document
►B DIRECTIVE 2007/46/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

of 5 September 2007
establishing a framework for the approval of motor vehicles and their trailers, and of systems,
components and separate technical units intended for such vehicles
(Framework Directive)
(Text with EEA relevance)
(OJ L 263, 9.10.2007, p. 1)
Amended by:
Official Journal
No page date
►M1 Commission Regulation (EC) No 1060/2008 of 7 October 2008 L 292 1 31.10.2008
►M2 Regulation (EC) No 78/2009 of the European Parliament and of the L 35 1 4.2.2009
Council of 14 January 2009
Council of 14 January 2009
►M4 Commission Regulation (EC) No 385/2009 of 7 May 2009 L 118 13 13.5.2009
Council of 18 June 2009
Council of 13 July 2009
►M7 Commission Directive 2010/19/EU of 9 March 2010 L 72 17 20.3.2010
►M8 amended by Commission Decision 2011/415/EU of 14 July 2011 L 185 76 15.7.2011
►M9 Commission Regulation (EU) No 371/2010 of 16 April 2010 L 110 1 1.5.2010
►M10 Commission Regulation (EU) No 183/2011 of 22 February 2011 L 53 4 26.2.2011
►M11 Commission Regulation (EU) No 582/2011 of 25 May 2011 L 167 1 25.6.2011
►M12 Commission Regulation (EU) No 678/2011 of 14 July 2011 L 185 30 15.7.2011
►M13 Commission Regulation (EU) No 65/2012 of 24 January 2012 L 28 24 31.1.2012
►M14 Commission Regulation (EU) No 1229/2012 of 10 December 2012 L 353 1 21.12.2012
►M15 Commission Regulation (EU) No 1230/2012 of 12 December 2012 L 353 31 21.12.2012
►M18 Commission Regulation (EU) No 195/2013 of 7 March 2013 L 65 1 8.3.2013

02007L0046 — EN — 18.01.2018 — 021.001 — 2
►M19 Council Directive 2013/15/EU of 13 May 2013 L 158 172 10.6.2013

►M21 Commission Regulation (EU) No 133/2014 of 31 January 2014 L 47 1 18.2.2014
►M23 Regulation (EU) No 540/2014 of the European Parliament and of the L 158 131 27.5.2014
Council of 16 April 2014
►M24 Commission Regulation (EU) No 1171/2014 of 31 October 2014 L 315 3 1.11.2014
►M25 Commission Regulation (EU) 2015/45 of 14 January 2015 L 9 1 15.1.2015
►M26 Commission Regulation (EU) 2015/166 of 3 February 2015 L 28 3 4.2.2015
►M27 Commission Regulation (EU) 2017/1151 of 1 June 2017 L 175 1 7.7.2017
►M28 Commission Regulation (EU) 2017/1154 of 7 June 2017 L 175 708 7.7.2017
►M29 Commission Regulation (EU) 2017/1347 of 13 July 2017 L 192 1 24.7.2017
►M30 Commission Regulation (EU) 2017/2400 of 12 December 2017 L 349 1 29.12.2017
Corrected by:
►C1 Corrigendum, OJ L 308, 25.11.2015, p. 11 (661/2009)

02007L0046 — EN — 18.01.2018 — 021.001 — 3
▼B
DIRECTIVE 2007/46/EC OF THE EUROPEAN PARLIAMENT
AND OF THE COUNCIL
of 5 September 2007
establishing a framework for the approval of motor vehicles and
their trailers, and of systems, components and separate technical
units intended for such vehicles
(Framework Directive)
(Text with EEA relevance)
CHAPTER I
GENERAL PROVISIONS
Article 1
Subject matter
This Directive establishes a harmonised framework containing the

administrative provisions and general technical requirements for
approval of all new vehicles within its scope and of the systems,
components and separate technical units intended for those vehicles,
with a view to facilitating their registration, sale and entry into
service within the Community.
This Directive also establishes the provisions for the sale and entry into
service of parts and equipment intended for vehicles approved in
accordance with this Directive.
Specific technical requirements concerning the construction and func

tioning of vehicles shall be laid down in application of this Directive in
regulatory acts, the exhaustive list of which is set out in Annex IV.
Article 2
Scope
1. This Directive applies to the type-approval of vehicles designed

and constructed in one or more stages for use on the road, and of
systems, components and separate technical units designed and
constructed for such vehicles.
It also applies to the individual approval of such vehicles.
This Directive also applies to parts and equipment intended for vehicles
covered by this Directive.
2. This Directive does not apply to the type-approval or individual

approval of the following vehicles:
02007L0046 — EN — 18.01.2018 — 021.001 — 4
▼B
(a) agricultural or forestry tractors, as defined in Directive 2003/37/EC
of the European Parliament and of the Council of 26 May 2003 on
type-approval of agricultural or forestry tractors, their trailers and
interchangeable towed machinery, together with their systems,
components and separate technical units (1) and trailers designed
and constructed specifically to be towed by them;
(b) quadricycles as defined in Directive 2002/24/EC of the European

Parliament and of the Council of 18 March 2002 relating to the
type-approval of two or three-wheel motor vehicles (2);
(c) tracked vehicles.
3. Type-approval or individual approval under this Directive is

optional for the following vehicles:
(a) vehicles designed and constructed for use principally on

construction sites or in quarries, port or airport facilities;
(b) vehicles designed and constructed for use by the armed services,
civil defence, fire services and forces responsible for maintaining
public order; and
(c) mobile machinery,
to the extent that these vehicles fulfil the requirements of this Directive.
Such optional approvals shall be without prejudice to the application of
Directive 2006/42/EC of the European Parliament and of the Council of
17 May 2006 on machinery (3).
4. An individual approval under this Directive is optional for the

following vehicles:
(a) vehicles intended exclusively for racing on roads;
(b) prototypes of vehicles used on the road under the responsibility of a

manufacturer to perform a specific test programme provided they
have been specifically designed and constructed for this purpose.
Article 3
Definitions
For the purposes of this Directive and of the regulatory acts listed in
Annex IV, save as otherwise provided therein:
1. ‘regulatory act’ means a separate directive or regulation or a

UNECE Regulation annexed to the Revised 1958 Agreement;
(1) OJ L 171, 9.7.2003, p. 1. Directive as last amended by Council Directive

2006/96/EC (OJ L 363, 20.12.2006, p. 81).
(2) OJ L 124, 9.5.2002, p. 1. Directive as last amended by Council Directive
2006/96/EC.
(3) OJ L 157, 9.6.2006, p. 24.
02007L0046 — EN — 18.01.2018 — 021.001 — 5
▼B
2. ‘separate directive or regulation’ means a directive or regulation
listed in Part I of Annex IV. This term includes also their imple
menting acts;
3. ‘type-approval’ means the procedure whereby a Member State

certifies that a type of vehicle, system, component or separate
technical unit satisfies the relevant administrative provisions and
technical requirements;
4. ‘national type-approval’ means a type-approval procedure laid down

by the national law of a Member State, the validity of such
approval being restricted to the territory of that Member State;
5. ‘EC type-approval’ means the procedure whereby a Member State

certifies that a type of vehicle, system, component or separate
technical unit satisfies the relevant administrative provisions and
technical requirements of this Directive and of the regulatory acts
listed in Annex IV or XI;
6. ‘individual approval’ means the procedure whereby a Member State

certifies that a particular vehicle, whether unique or not, satisfies the
relevant administrative provisions and technical requirements;
7. ‘multi-stage type-approval’ means the procedure whereby one or

more Member States certify that, depending on the state of
completion, an incomplete or completed type of vehicle satisfies
the relevant administrative provisions and technical requirements
of this Directive;
8. ‘step-by-step type-approval’ means a vehicle approval procedure

consisting in the step-by-step collection of the whole set of EC
type-approval certificates for the systems, components and
separate technical units relating to the vehicle, and which leads,
at the final stage, to the approval of the whole vehicle;
9. ‘single-step type-approval’ means a procedure consisting in the

approval of a vehicle as a whole by means of a single operation;
10. ‘mixed type-approval’ means a step-by-step type-approval

procedure for which one or more system approvals are achieved
during the final stage of the approval of the whole vehicle, without
it being necessary to issue the EC type-approval certificates for
those systems;
11. ‘motor vehicle’ means any power-driven vehicle which is moved by

its own means, having at least four wheels, being complete,
completed or incomplete, with a maximum design speed
exceeding 25 km/h;
12. ‘trailer’ means any non-self-propelled vehicle on wheels which is

designed and constructed to be towed by a motor vehicle;
13. ‘vehicle’ means any motor vehicle or its trailer as defined in points
(11) and (12);
14. ‘hybrid motor vehicle’ means a vehicle with at least two different
energy converters and two different energy storage systems (on-
vehicle) for the purpose of vehicle propulsion;
02007L0046 — EN — 18.01.2018 — 021.001 — 6
▼B
15. ‘hybrid electric vehicle’ means a hybrid vehicle that, for the
purpose of mechanical propulsion, draws energy from both of the
following on-vehicle sources of stored energy/power:
— a consumable fuel,
— an electrical energy/power storage device (e.g. battery,

capacitor, flywheel/generator, etc.);
16. ‘mobile machinery’ means any self-propelled vehicle which is

designed and constructed specifically to perform work which,
because of its construction characteristics, is not suitable for
carrying passengers or for transporting goods. Machinery mounted
on a motor vehicle chassis shall not be considered as mobile
machinery;
17. ‘type of vehicle’ means vehicles of a particular category which do

not differ in at least the essential respects specified in Section B of
Annex II. A type of vehicle may contain variants and versions as
defined in Section B of Annex II;
18. ‘base vehicle’ means any vehicle which is used at the initial stage
of a multi-stage type-approval process;
19. ‘incomplete vehicle’ means any vehicle which must undergo at least
one further stage of completion in order to meet the relevant
technical requirements of this Directive;
20. ‘completed vehicle’ means a vehicle, resulting from the process of

multi-stage type-approval, which meets the relevant technical
requirements of this Directive;
21. ‘complete vehicle’ means any vehicle which need not be completed
in order to meet the relevant technical requirements of this
Directive;
22. ‘end-of-series vehicle’ means any vehicle that is part of a stock

which cannot be registered or sold or entered into service owing
to the entry into force of new technical requirements against which
it has not been approved;
23. ‘system’ means an assembly of devices combined to perform one or

more specific functions in a vehicle and which is subject to the
requirements of any of the regulatory acts;
24. ‘component’ means a device subject to the requirements of a regu

latory act and intended to be part of a vehicle, which may be
type-approved independently of a vehicle where the regulatory act
makes express provisions for so doing;
25. ‘separate technical unit’ means a device subject to the requirements

of a regulatory act and intended to be part of a vehicle, which may
be type-approved separately, but only in relation to one or more
specified types of vehicle where the regulatory act makes express
provisions for so doing;
02007L0046 — EN — 18.01.2018 — 021.001 — 7
▼B
26. ‘original parts or equipment’ means parts or equipment which are
manufactured according to the specifications and production
standards provided by the vehicle manufacturer for the production
of parts or equipment for the assembly of the vehicle in question.
This includes parts or equipment which are manufactured on the
same production line as these parts or equipment. It is presumed
unless the contrary is proven, that parts constitute original parts if
the part manufacturer certifies that the parts match the quality of the
components used for the assembly of the vehicle in question and
have been manufactured according to the specifications and
production standards of the vehicle manufacturer;
27. ‘manufacturer’ means the person or body who is responsible to the

approval authority for all aspects of the type-approval or authori
sation process and for ensuring conformity of production. It is not
essential that the person or body be directly involved in all stages of
the construction of the vehicle, system, component or separate
technical unit which is the subject of the approval process;
28. ‘manufacturer’s representative’ means any natural or legal person

established in the Community who is duly appointed by the manu
facturer to represent him before the approval authority and to act on
his behalf in matters covered by this Directive, and where reference
is made to the term ‘manufacturer’, it is to be understood as indi
cating either the manufacturer or his representative;
29. ‘approval authority’ means the authority of a Member State with

competence for all aspects of the approval of a type of vehicle,
system, component or separate technical unit or of the individual
approval of a vehicle; for the authorisation process, for issuing and,
if appropriate, withdrawing approval certificates; for acting as the
contact point for the approval authorities of other Member States;
for designating the technical services and for ensuring that the
manufacturer meets his obligations regarding the conformity of
production;
30. ‘competent authority’ in Article 42 means either the approval

authority or a designated authority, or an accreditation body
acting on their behalf;
31. ‘technical service’ means an organisation or body designated by the

approval authority of a Member State as a testing laboratory to
carry out tests, or as a conformity assessment body to carry out
the initial assessment and other tests or inspections, on behalf of the
approval authority, it being possible for the approval authority itself
to carry out those functions;
32. ‘virtual testing method’ means computer simulations including

calculations which demonstrate whether a vehicle, a system, a
component or a separate technical unit fulfils the technical
requirements of a regulatory act. For testing purposes, a virtual
method does not require the use of a physical vehicle, system,
component or separate technical unit;
02007L0046 — EN — 18.01.2018 — 021.001 — 8
▼B
33. ‘type-approval certificate’ means the document whereby the
approval authority officially certifies that a type of vehicle,
system, component or separate technical unit is approved;
34. ‘EC type-approval certificate’ means the certificate set out in

Annex VI or in the corresponding annex to a separate directive
or regulation, the communication form set out in the relevant
Annex to one of the UNECE Regulations listed in Part I or Part
II of Annex IV to this Directive, being deemed to be equivalent
thereto;
35. ‘individual approval certificate’ means the document whereby the

approval authority officially certifies that a particular vehicle is
approved;
36. ‘certificate of conformity’ means the document set out in Annex IX,
issued by the manufacturer and certifying that a vehicle belonging
to the series of the type approved in accordance with this Directive
complied with all regulatory acts at the time of its production;
37. ‘information document’ means the document set out in Annex I or

Annex III, or in the corresponding Annex to a separate directive, or
regulation, that prescribes the information to be supplied by an
applicant, it being permissible to supply the information
document in the form of an electronic file;
38. ‘information folder’ means the complete folder, including the

information document, file, data, drawings, photographs, and so
on, supplied by the applicant, it being permissible to supply the
information folder in the form of an electronic file;
39. ‘information package’ means the information folder accompanied

by the test reports and all other documents added by the
technical service or by the approval authority to the information
folder in the course of carrying out their functions, it being
permissible to supply the information package in the form of an
electronic file;
40. ‘index to the information package’ means the document listing the
contents of the information package, suitably numbered or
otherwise marked so as to identify clearly all the pages, the
format of that document being such as to present a record of the
successive steps in the management of the EC type-approval, in
particular the dates of the revisions and updating.
CHAPTER II
GENERAL OBLIGATIONS
Article 4
Obligations of Member States
1. Member States shall ensure that manufacturers applying for

approval comply with their obligations under this Directive.
02007L0046 — EN — 18.01.2018 — 021.001 — 9
▼B
2. Member States shall approve only such vehicles, systems,
components or separate technical units as satisfy the requirements of
this Directive.
3. Member States shall register or permit the sale or entry into

service only of such vehicles, components and separate technical units
as satisfy the requirements of this Directive.
They shall not prohibit, restrict or impede the registration, sale, entry
into service or circulation on the road of vehicles, components or
separate technical units, on grounds related to aspects of their
construction and functioning covered by this Directive, if they satisfy
the requirements of the latter.
4. Member States shall establish or appoint the authorities competent

in matters concerning approval, and notify to the Commission such
establishment or appointment in accordance with Article 43.
The notification act of the approval authorities shall include the name,
the address, including electronic address, and their area of responsibility.
Article 5
Obligations of manufacturers
1. The manufacturer is responsible to the approval authority for all

aspects of the approval process and for ensuring conformity of
production, whether or not the manufacturer is directly involved in all
stages of the construction of a vehicle, system, component or separate
technical unit.
2. In the case of multi-stage type-approval, each manufacturer is

responsible for the approval and conformity of production of the
systems, components or separate technical units added at the stage of
vehicle completion handled by him.
The manufacturer who modifies components or systems already

approved at earlier stages shall be responsible for the approval and
conformity of production of those components and systems.
3. For the purposes of this Directive, a manufacturer established

outside the Community shall appoint a representative established in
the Community to represent him before the approval authority.
CHAPTER III
EC TYPE-APPROVAL PROCEDURES
Article 6
Procedures to be followed for the EC type-approval of vehicles
1. The manufacturer may choose one of the following procedures:
(a) step-by-step type-approval;
(b) single-step type-approval;

02007L0046 — EN — 18.01.2018 — 021.001 — 10
▼B
(c) mixed type-approval.
2. An application for step-by-step type-approval shall consist of the

information folder containing the information required under Annex III
and shall be accompanied by the complete set of type-approval
certificates required pursuant to each of the applicable regulatory acts
listed in Annex IV or Annex XI. In the case of the type-approval of a
system or separate technical unit, pursuant to the applicable regulatory
acts, the approval authority shall have access to the related information
package until such time as the approval is either issued or refused.
3. An application for single-step type-approval shall consist of the

information folder containing the relevant information required under
Annex I, in relation to the regulatory acts specified in Annex IV or
Annex XI and, where applicable, in Part II of Annex III.
4. In the case of a mixed type-approval procedure, the approval

authority may exempt a manufacturer from the obligation to produce
one or more EC system type-approval certificates, provided that the
information folder is supplemented by the particulars, specified in
Annex I, required for the approval of those systems during the
vehicle approval phase, in which case each of the EC type-approval
certificates thus waived shall be replaced by a test report.
5. Without prejudice to paragraphs 2, 3 and 4, the following

information shall be supplied for the purposes of multi-stage
type-approval:
(a) at the first stage, those parts of the information folder and the EC
type-approval certificates required for a complete vehicle which are
relevant to the state of completion of the base vehicle;
(b) at the second and subsequent stages, those parts of the information
folder and the EC type-approval certificates which are relevant to
the current stage of construction, together with a copy of the EC
type-approval certificate for the vehicle issued at the preceding stage
of construction; in addition, the manufacturer shall supply full
details of any changes or additions that he has made to the vehicle.
The information specified in points (a) and (b) may be supplied in

accordance with the mixed type-approval procedure set out in
paragraph 4.
6. The manufacturer shall submit the application to the approval

authority. Only one application may be submitted in respect of a
particular type of vehicle and it may be submitted in only one
Member State.
A separate application shall be submitted for each type to be approved.

02007L0046 — EN — 18.01.2018 — 021.001 — 11
▼B
7. The approval authority may, by reasoned request, call upon the
manufacturer to supply any additional information needed to enable a
decision to be taken on what tests are required or to facilitate the
execution of those tests.
8. The manufacturer shall make available to the approval authority as

many vehicles as are necessary to enable the type-approval procedure to
be conducted satisfactorily.
Article 7
Procedure to be followed for the EC type-approval of systems,
components or separate technical units
1. The manufacturer shall submit the application to the approval

authority. Only one application may be submitted in respect of a
particular type of system, component or separate technical unit and it
may be submitted in only one Member State. A separate application
shall be submitted for each type to be approved.
2. The application shall be accompanied by the information folder,

the content of which is specified in the separate directives or
regulations.
3. The approval authority may, by reasoned request, call upon the

manufacturer to supply any additional information needed to enable a
decision to be taken on what tests are required or to facilitate the
execution of those tests.
4. The manufacturer shall make available to the approval authority as

many vehicles, components or separate technical units as are required
under the relevant separate directives or regulations for the performance
of the required tests.
CHAPTER IV
CONDUCT OF EC TYPE-APPROVAL PROCEDURES
Article 8
General provisions
1. Member States may not grant any EC type-approval without first

ensuring that the procedures referred to in Article 12 have been duly
and satisfactorily implemented.
2. Member States shall grant EC type-approvals in accordance with

Articles 9 and 10.
02007L0046 — EN — 18.01.2018 — 021.001 — 12
▼B
3. If a Member State finds that a type of vehicle, system, component
or separate technical unit, albeit in conformity with the required
provisions, presents a serious risk to road safety or seriously harms
the environment or seriously harms public health, it may refuse to
grant EC type-approval. In this case, it shall immediately send the
other Member States and the Commission a detailed file explaining
the reasons for its decision and setting out the evidence for its findings.
4. EC type-approval certificates shall be numbered in accordance

with the method set out in Annex VII.
5. The approval authority shall, within 20 working days, send to the

approval authorities of the other Member States a copy of the EC
vehicle type-approval certificate, together with the attachments, for
each type of vehicle which it has approved. The hard copy may be
replaced by an electronic file.
6. The approval authority shall inform without delay the approval

authorities of the other Member States of its refusal or withdrawal of
any vehicle approval, together with the reasons for its decision.
7. The approval authority shall send at three-monthly intervals to the

approval authorities of the other Member States a list of the system,
component or separate technical unit EC type-approvals it has granted,
amended, refused to grant or withdrawn during the preceding period.
That list shall contain the particulars specified in Annex XIV.
8. If so requested by another Member State, the Member State which

has granted an EC type-approval shall, within 20 working days of
receiving that request, send a copy of the EC type-approval certificate
in question, together with the attachments. The hard copy may be
replaced by an electronic file.
Article 9
Specific provisions concerning vehicles
1. Member States shall grant an EC approval in respect of:
(a) a type of vehicle which conforms to the particulars in the

information folder and which meets the technical requirements
specified by the relevant regulatory acts listed in Annex IV;
(b) a type of special-purpose vehicle which conforms to the particulars

in the information folder and which meets the technical
requirements specified by the relevant regulatory acts listed in
Annex XI.
The procedures set out in Annex V shall apply.
2. Member States shall grant a multi-stage type-approval in respect of

a type of incomplete or completed vehicle which conforms to the
particulars in the information folder and which meets the technical
requirements specified by the relevant regulatory acts listed in
Annex IV or Annex XI, having regard to the state of completion of
the vehicle.
02007L0046 — EN — 18.01.2018 — 021.001 — 13
▼B
The multi-stage type-approval shall apply also to complete vehicles
converted or modified by another manufacturer.
The procedures set out in Annex XVII shall apply.
3. In respect of each type of vehicle, the approval authority shall:
(a) complete all the relevant sections of the EC type-approval

certificate, including the test results sheet appended thereto, in
accordance with the model set out in Annex VIII;
(b) compile or verify the index to the information package;
(c) issue the completed certificate, together with its attachments, to the
applicant without unjustified delay.
4. In the case of an EC type-approval in relation to which, in

accordance with Articles 20 or 22 or Annex XI, restrictions have
been imposed as to its validity, or certain provisions of the regulatory
acts have been waived, the EC type-approval certificate shall specify
those restrictions or waivers.
5. Where particulars in the information folder specify provisions for

special purpose vehicles as indicated in Annex XI, the EC type-approval
certificate shall specify those provisions.
6. Where the manufacturer chooses the mixed type-approval

procedure, the approval authority shall complete, in Part III of the
information document, the model for which is set out in Annex III,
the references for the test reports, established by regulatory acts, for
which no EC type-approval certificate is available.
7. Where the manufacturer chooses the single-step type-approval

procedure, the approval authority shall establish the list of applicable
regulatory acts, the template of which is shown in the Appendix to
Annex VI, and append that list to the EC type-approval certificate.
Article 10
Specific provisions concerning systems, components or separate
technical units
1. Member States shall grant an EC type-approval in respect of a

system which conforms to the particulars in the information folder and
which meets the technical requirements laid down in the relevant
separate directive or regulation, as prescribed in Annex IV or Annex XI.
2. Member States shall grant a component or separate technical unit

EC type-approval in respect of a component or separate technical unit
which conforms to the particulars in the information folder and which
meets the technical requirements laid down in the relevant separate
directive or regulation, as prescribed in Annex IV.
02007L0046 — EN — 18.01.2018 — 021.001 — 14
▼B
3. Where components or separate technical units, whether or not
intended for repair, servicing or maintenance, are also covered by a
system type-approval with respect to a vehicle, no additional
component or separate technical unit approval shall be required unless
provided for under the relevant regulatory act.
4. Where a component or separate technical unit fulfils its function or

offers a specific feature only in conjunction with other parts of the
vehicle, thereby making it possible to verify compliance with the
requirements only when the component or separate technical unit is
operating in conjunction with those other vehicle parts, the scope of
the EC type-approval of the component or the separate technical unit
shall be restricted accordingly. In such cases, the EC type-approval
certificate shall specify any restriction on its use and shall indicate
the special conditions for its mounting. When such a component or
separate technical unit is fitted by the vehicle manufacturer, compliance
with any applicable restrictions on use or conditions for mounting shall
be verified at the time when the vehicle is approved.
Article 11
Tests required for EC type-approval
1. Compliance with the technical prescriptions laid down in this

Directive and in the regulatory acts listed in Annex IV shall be demon
strated by means of appropriate tests performed by designated technical
services.
The test procedures, the specific equipment and tools necessary to

perform those tests shall be described in each of the regulatory acts.
2. The required tests shall be performed on vehicles, components and

separate technical units which are representative of the type to be
approved.
However, the manufacturer may select, in agreement with the approval

authority, a vehicle, a system, a component or a separate technical unit
which, while not representative of the type to be approved, combines a
number of the most unfavourable features with regard to the required
level of performance. Virtual testing methods may be used to aid
decision-making during the selection process.
3. As alternatives to the test procedures referred to in paragraph 1

and with the agreement of the approval authority, virtual testing
methods may be used at the request of the manufacturer with respect
to the regulatory acts listed in Annex XVI.
4. The general conditions which virtual testing methods must fulfil

are set out in Appendix 1 to Annex XVI.
For each of the regulatory acts listed in Annex XVI, the specific testing
conditions and the administrative provisions related thereto shall be laid
down in Appendix 2 to that Annex.
02007L0046 — EN — 18.01.2018 — 021.001 — 15
▼B
5. The Commission shall establish the list of the regulatory acts for
which virtual testing methods are permitted, the specific conditions and
the administrative provisions related thereto. These measures, designed
to amend non-essential elements of this Directive, inter alia by supple
menting it, shall be established and updated in accordance with the
regulatory procedure with scrutiny referred to in Article 40(2).
Article 12
Conformity of production arrangements
1. The Member State which grants an EC type-approval shall take

the necessary measures in accordance with Annex X to verify, if need
be in cooperation with the approval authorities of the other Member
States, that adequate arrangements have been made to ensure that
production vehicles, systems, components or separate technical units,
as the case may be, conform to the approved type.
2. The Member State which has granted an EC type-approval shall

take the necessary measures in accordance with Annex X in relation to
that approval to verify, if need be in cooperation with the approval
authorities of the other Member States, that the arrangements referred
to in paragraph 1 continue to be adequate and that production vehicles,
systems, components or separate technical units, as the case may be,
continue to conform to the approved type.
Verification to ensure that products conform to the approved type shall

be limited to the procedures set out in Annex X and in those regulatory
acts that contain specific requirements. To that end, the approval
authority of the Member State which has granted the EC
type-approval may carry out any of the checks or tests prescribed in
any of the regulatory acts listed in Annex IV or Annex XI on samples
taken in the premises of the manufacturer, including production
facilities.
3. When a Member State which has granted an EC type-approval

establishes that the arrangements referred to in paragraph 1 are not
being applied, deviate significantly from the arrangements and control
plans agreed, or have ceased to be applied, although production is not
discontinued, that Member State shall take the necessary measures,
including the withdrawal of the type-approval, to ensure that the
conformity of production procedure is followed correctly.
CHAPTER V
AMENDMENTS TO EC TYPE-APPROVALS
Article 13
General provisions
1. The manufacturer shall inform without delay the Member State

that granted the EC type-approval of any change in the particulars
recorded in the information package. That Member State shall decide,
in accordance with the rules laid down in this Chapter, which procedure
is to be followed. Where necessary, the Member State may decide, in
consultation with the manufacturer, that a new EC type-approval is to
be granted.
02007L0046 — EN — 18.01.2018 — 021.001 — 16
▼B
2. An application for the amendment of an EC type-approval shall be
submitted exclusively to the Member State that granted the original EC
type-approval.
3. If the Member State finds that, for the purposes of making an

amendment, fresh inspections or fresh tests are necessary, it shall
inform the manufacturer accordingly. The procedures referred to in
Articles 14 and 15 shall apply only after the requisite fresh inspections
or fresh tests have been successfully carried out.
Article 14
Specific provisions concerning vehicles
1. If particulars recorded in the information package have changed,

the amendment shall be designated a ‘revision’.
In such cases, the approval authority shall issue the revised page of the
information package as necessary, marking each revised pages to show
clearly the nature of the change and the date of re-issue. A consolidated,
updated version of the information package, accompanied by a detailed
description of the changes, shall be deemed to meet this requirement.
2. The revision shall be designated an ‘extension’ if, in addition to

the provisions of paragraph 1:
(a) further inspections or fresh tests are required;
(b) any information on the EC type-approval certificate, with the

exception of its attachments, has changed;
(c) new requirements under any of the regulatory acts applicable to the
approved vehicle type enter into force.
In such cases, the approval authority shall issue a revised EC

type-approval certificate denoted by an extension number, incremented
in accordance with the number of successive extensions already granted.
The approval certificate shall show clearly the reason for the extension
and the date of re-issue.
3. Whenever amended pages or a consolidated, updated version are

issued, the index to the information package attached to the approval
certificate shall be amended accordingly to show the date of the most
recent extension or revision, or the date of the most recent consolidation
of the updated version.
4. No amendment to the approval of a type of vehicle shall be

required if the new requirements referred to in paragraph 2(c) are,
from a technical point of view, irrelevant to that type of vehicle or
concern categories of vehicle other than the category to which it
belongs.
02007L0046 — EN — 18.01.2018 — 021.001 — 17
▼B
Article 15
Specific provisions concerning systems, components or separate
technical units
1. If particulars recorded in the information package have changed,

the amendment shall be designated a ‘revision’.
In such cases, the approval authority shall issue the revised pages of the
information package as necessary, marking each revised page to show
clearly the nature of the change and the date of re-issue. A consolidated,
updated version of the information package, accompanied by a detailed
description of the changes, shall be deemed to meet this requirement.
2. The revision shall be designated an ‘extension’ if, in addition to

the provisions of paragraph 1:
(a) further inspections or fresh tests are required;
(b) any information on the EC type-approval certificate, with the

exception of its attachments, has changed;
(c) new requirements under any of the regulatory acts applicable to the
approved system, component or separate technical unit enter into
force.
In such cases, the approval authority shall issue a revised EC

type-approval certificate denoted by an extension number, incremented
in accordance with the number of successive extensions already granted.
In cases where the amendment is necessitated by the application of
paragraph 2(c), the third section of the approval number shall be
updated.
The approval certificate shall show clearly the reason for the extension
and the date of re-issue.
3. Whenever amended pages or a consolidated, updated version are

issued, the index to the information package attached to the approval
certificate shall be amended accordingly to show the date of the most
recent extension or revision, or the date of the most recent consolidation
of the updated version.
Article 16
Issue and notification of amendments
1. In the case of an extension, the approval authority shall update all

relevant sections of the EC type-approval certificate, the attachments
thereto, and the index to the information package. The updated
certificate and its attachments shall be issued to the applicant without
unjustified delay.
2. In the case of a revision, the revised documents or the

consolidated, updated version, as appropriate, including the revised
index to the information package, shall be issued by the approval
authority to the applicant without unjustified delay.
3. The approval authority shall notify any amendment made to EC

type-approvals to the approval authorities of the other Member States in
accordance with the procedures referred to in Article 8.
02007L0046 — EN — 18.01.2018 — 021.001 — 18
▼B
CHAPTER VI
VALIDITY OF AN EC TYPE-APPROVAL OF VEHICLES
Article 17
Termination of validity
1. An EC type-approval of a vehicle shall cease to be valid in any of

the following cases:
(a) new requirements in any regulatory act applicable to the approved

vehicle become mandatory for the registration, sale or entry into
service of new vehicles, and it is not possible to update the approval
accordingly;
(b) production of the approved vehicle is definitively discontinued

voluntarily;
(c) the validity of the approval expires by virtue of a special restriction.
2. Where only one variant within a type or one version within a

variant becomes invalid, the EC type-approval of the vehicle in
question shall lose validity only in so far as the particular variant or
version is concerned.
3. When production of a particular type of vehicle is definitively

discontinued, the manufacturer shall notify the approval authority that
granted the EC type-approval for that vehicle. Upon receiving such
notification, that authority shall inform the approval authorities of the
other Member States accordingly within 20 working days.
Article 27 shall apply only to discontinuation in the circumstances

referred to in paragraph 1(a) of this Article.
4. Without prejudice to paragraph 3, in cases where an EC

type-approval of a vehicle is due to become invalid, the manufacturer
shall notify the approval authority that granted the EC type-approval.
The approval authority shall without unjustified delay communicate all

relevant information to the approval authorities of the other Member
States so as to enable the application, where appropriate, of Article 27.
That communication shall specify, in particular, the date of production
and the vehicle identification number of the last vehicle produced.
CHAPTER VII
CERTIFICATE OF CONFORMITY AND MARKINGS
Article 18
Certificate of conformity
1. The manufacturer, in his capacity as the holder of an EC

type-approval of a vehicle, shall deliver a certificate of conformity to
accompany each vehicle, whether complete, incomplete or completed,
that is manufactured in conformity with the approved vehicle type.
02007L0046 — EN — 18.01.2018 — 021.001 — 19
▼B
In the case of an incomplete or completed vehicle, the manufacturer
shall complete only those items on side 2 of the certificate of
conformity which have been added or changed at the current stage of
approval and, if applicable, shall attach to the certificate all certificates
of conformity delivered at the previous stage.
2. The certificate of conformity shall be drawn up in one of the

official languages of the Community. Any Member State may request
the certificate of conformity to be translated into its own language or
languages.
3. The certificate of conformity shall be designed to prevent forgery.

To that end, the paper used shall be protected either by coloured
graphics or by a watermark in the form of the manufacturer’s identifi
cation mark.
4. The certificate of conformity shall be completed in its entirety and

shall not contain restrictions as regards the use of the vehicle other than
those provided for in a regulatory act.
5. The certificate of conformity as set out in Part I of Annex IX for

vehicles approved in accordance with the provisions of Article 20(2)
shall display in the title thereof the phrase ‘For complete/completed
vehicles, type-approved in application of Article 20 (provisional
approval).’.
6. The certificate of conformity, as set out in Part I of Annex IX for

vehicles type-approved in accordance with Article 22 shall display in
the title thereof the phrase ‘For complete/completed vehicles
type-approved in small series’, and in close proximity thereto the year
of production followed by a sequential number, between 1 and the limit
indicated in the table set out in Annex XII, denoting, in respect of each
year of production, the position of that vehicle within the production
allocated for that year.
7. Without prejudice to the provisions of paragraph 1, the manu

facturer may transmit data or information contained in the certificate
of conformity by electronic mean to the registration authority of the
Member State.
8. A duplicate of the certificate of conformity may be issued only by

the manufacturer. The word ‘duplicate’ must be clearly visible on the
face of any duplicate certificate.
Article 19
EC type-approval mark
1. The manufacturer of a component or separate technical unit,

whether or not it is part of a system, shall affix to each component
or unit manufactured in conformity with the approved type the EC
type-approval mark, required by the relevant separate directive or
regulation.
2. Where no EC type-approval mark is required, the manufacturer

shall affix at least his trade name or trade mark, and the type number
and/or an identification number.
02007L0046 — EN — 18.01.2018 — 021.001 — 20
▼B
3. The EC type-approval mark shall be in accordance with the
Appendix to Annex VII.
CHAPTER VIII
NEW TECHNOLOGIES OR CONCEPTS INCOMPATIBLE WITH

SEPARATE DIRECTIVES
Article 20
Exemptions for new technologies or new concepts
1. Member States may, on application by the manufacturer, grant an

EC type-approval in respect of a type of system, component or separate
technical unit that incorporates technologies or concepts which are
incompatible with one or more regulatory acts listed in Part I of
Annex IV, subject to authorisation being granted by the Commission
in accordance with the procedure referred to in Article 40(3).
2. Pending the decision as to whether or not authorisation is granted,

the Member State may grant a provisional approval, valid only in its
territory, in respect of a type of vehicle covered by the exemption
sought, provided that it informs the Commission and the other
Member States thereof without delay by means of a file containing
the following elements:
(a) the reasons why the technologies or concepts in question make the
system, component or separate technical unit incompatible with the
requirements;
(b) a description of the safety and environmental considerations

concerned and the measures taken;
(c) a description of the tests, including their results, demonstrating that,

by comparison with the requirements from which exemption is
sought, at least an equivalent level of safety and environmental
protection is ensured.
3. Other Member States may decide to accept the provisional

approval referred to in paragraph 2 on their territory.
4. The Commission shall decide, in accordance with the procedure

referred to in Article 40(3), whether or not to allow the Member State to
grant an EC type-approval in respect of that type of vehicle.
Where appropriate, the decision shall also specify whether its validity is
subject to any restrictions, such as time-limits. In all cases, the validity
of the approval shall not be less than 36 months.
If the Commission decides to refuse authorisation, the Member State

shall immediately give notice to the holder of the provisional
type-approval referred to in paragraph 2 of this Article that the provi
sional approval will be revoked six months after the date of the
Commission’s decision. However, vehicles manufactured in conformity
with the provisional approval before it was revoked shall be permitted
to be registered, sold or enter service in any Member State that accepted
the provisional approval.
02007L0046 — EN — 18.01.2018 — 021.001 — 21
▼B
5. This Article does not apply where a system, component or
separate technical unit complies with a UNECE Regulation to which
the Community has acceded.
Article 21
Action required
1. Where the Commission finds that there are sound grounds for
granting an exemption pursuant to Article 20, it shall immediately
take the necessary steps to adapt the separate directives or regulations
concerned to technological developments. These measures, designed to
amend non-essential elements of the separate directives or regulations
listed in Part I of Annex IV shall be adopted in accordance with the
regulatory procedure with scrutiny referred to in Article 40(2).
Where the exemption pursuant to Article 20 relates to a UNECE Regu

lation, the Commission shall propose an amendment to the relevant
UNECE Regulation in accordance with the procedure applicable
under the Revised 1958 Agreement.
2. As soon as the relevant regulatory acts have been amended, any

restriction attaching to the exemption shall be lifted immediately.
If the necessary steps to adapt the regulatory acts have not been taken,
the validity of an exemption may be extended, at the request of the
Member State which granted the approval, by another decision adopted
in accordance with the procedure referred to in Article 40(3).
CHAPTER IX
VEHICLES PRODUCED IN SMALL SERIES
Article 22
EC type-approval of small series
1. At the request of the manufacturer and within the quantitative

limits set out in Section 1 of Part A of Annex XII, Member States
shall grant, in accordance with the procedure referred to in Article 6(4),
an EC type-approval in respect of a type of vehicle which satisfies at
least the requirements listed in the Appendix to Part I of Annex IV.
2. Paragraph 1 shall not apply to special purpose vehicles.
3. EC type-approval certificates shall be numbered in accordance

with Annex VII.
Article 23
National type-approval of small series
1. In the case of vehicles produced within the quantitative limits

specified in Section 2 of Part A of Annex XII, Member States may
waive one or more of the provisions of one or more of the regulatory
acts listed in Annex IV or Annex XI, provided that they lay down
relevant alternative requirements.
02007L0046 — EN — 18.01.2018 — 021.001 — 22
▼B
‘Alternative requirements’ means administrative provisions and
technical requirements which aim to ensure a level of road safety and
environmental protection which is equivalent to the greatest extent prac
ticable to the level provided for by the provisions of Annex IV or
Annex XI, as appropriate.
2. Member States may, in the case of the vehicles referred to in

paragraph 1, waive one or more of the provisions of this Directive.
3. The provisions referred to in paragraphs 1 and 2 shall only be

waived where a Member State has reasonable grounds for so doing.
4. For the purpose of type-approval of vehicles under this Article,

Member States shall accept systems, components or separate technical
units which are type-approved in accordance with the regulatory acts
listed in Annex IV.
5. The type-approval certificate shall specify the nature of the

waivers granted pursuant to paragraphs 1 and 2.
The type-approval certificate, the model for which is set out in

Annex VI, shall not bear the heading ‘EC vehicle type-approval
certificate’. However, type-approval certificates shall be numbered in
accordance with Annex VII.
6. The validity of the type-approval shall be restricted to the territory

of the Member State that granted the approval. However, if the manu
facturer so requests, the approval authority shall send by registered mail
or by electronic mail a copy of the type-approval certificate and its
attachments to the approval authorities of the Member States designated
by the manufacturer.
Within 60 days of receipt, such a Member State shall decide whether or

not it accepts the type-approval. It shall formally communicate that
decision to the approval authority referred to in the first subparagraph.
A Member State shall not refuse the type-approval unless it has

reasonable grounds to believe that the technical provisions according
to which the vehicle was approved are not equivalent to its own.
7. On request of an applicant who wishes to sell, register or put into

service a vehicle in another Member State, the Member State that
granted the approval shall provide the applicant with a copy of the
type-approval certificate including the information package.
A Member State shall permit the sale, registration or entry into service
of this vehicle unless it has reasonable grounds to believe that the
technical provisions according to which the vehicle was approved are
not equivalent to its own.
02007L0046 — EN — 18.01.2018 — 021.001 — 23
▼B
CHAPTER X
INDIVIDUAL APPROVALS
Article 24
Individual approvals
1. Member States may exempt a particular vehicle, whether unique or

not, from compliance with one or more of the provisions of this
Directive or with one or more of the regulatory acts listed in
Annex IV or Annex XI, provided that they impose alternative
requirements.
The provisions referred to in subparagraph 1 shall only be waived

where a Member State has reasonable grounds for so doing.
‘Alternative requirements’ means administrative provisions and

technical requirements which aim to ensure a level of road safety and
environmental protection, which is equivalent to the greatest extent
practicable to the level provided for by the provisions of Annex IV
or Annex XI, as appropriate.
2. Member States shall not carry out destructive tests. They shall use
any relevant information provided by the applicant establishing
compliance with the alternative requirements.
3. Member States shall accept any system, component or separate

technical unit EC type-approval instead of the alternative requirements.
4. An application for individual approval shall be submitted by the

manufacturer or by the owner of the vehicle or by a person acting on
their behalf, provided the latter is established in the Community.
5. A Member State shall grant an individual approval if the vehicle

conforms to the description appended to the application and satisfies the
applicable technical requirements and shall without unjustified delay
issue an individual approval certificate.
The format of the individual approval certificate shall be based on the

template of the EC type-approval certificate set out in Annex VI and
shall contain at least the information necessary to complete the appli
cation for registration provided for in Council Directive 1999/37/EC of
29 April 1999 on the registration documents for vehicles (1). Individual
approval certificates shall not bear the heading ‘EC vehicle approval’.
An individual approval certificate shall bear the vehicle identification

number of the vehicle concerned.
6. The validity of an individual approval shall be restricted to the

territory of the Member State that granted the approval.
Where an applicant wishes to sell, register or put into service in another

Member State a vehicle which has been granted an individual approval,
the Member State that granted the approval shall, on request, provide
the applicant with a statement of the technical provisions against which
the vehicle was approved.
(1) OJ L 138, 1.6.1999, p. 57. Directive as last amended by Directive

2006/103/EC (OJ L 363, 20.12.2006, p. 344).
02007L0046 — EN — 18.01.2018 — 021.001 — 24
▼B
With regard to a vehicle which has been granted an individual approval
by a Member State in accordance with the provisions of this Article,
another Member State shall permit that vehicle to be sold, registered or
to enter into service unless it has reasonable grounds to believe that the
technical provisions against which the vehicle was approved are not
equivalent to its own.
7. At the request of the manufacturer or of the owner of the vehicle,

Member States shall grant an individual approval to a vehicle which
complies with the provisions of this Directive and with the regulatory
acts listed in Annex IV or Annex XI, as appropriate.
In such a case, Member States shall accept the individual approval and
shall permit the sale, registration and entry into service of the vehicle.
8. The provisions of this Article may apply to vehicles which have

been type-approved in accordance with this Directive and which have
been modified before their first registration or entry into service.
Article 25
Specific provisions
1. The procedure set out in Article 24 may apply to a particular

vehicle during the successive stages of its completion in accordance
with a multi-stage type-approval procedure.
2. The procedure set out in Article 24 may not replace an inter

mediate stage within the normal sequence of a multi-stage
type-approval procedure and may not apply for the purposes of
obtaining the first-stage approval of a vehicle.
CHAPTER XI
REGISTRATION, SALE AND ENTRY INTO SERVICE
Article 26
Registration, sale and entry into service of vehicles
1. Without prejudice to the provisions of Articles 29 and 30, Member

States shall register, and permit the sale or entry into service of, vehicles
only if they are accompanied by a valid certificate of conformity issued
in accordance with Article 18.
In the case of incomplete vehicles, Member States shall permit the sale
of such vehicles but may refuse their permanent registration and entry
into service for such time as the vehicles remain incomplete.
2. Vehicles exempted from the requirement concerning a certificate

of conformity may be registered, sold or put into service only if they
satisfy the relevant technical requirements of this Directive.
02007L0046 — EN — 18.01.2018 — 021.001 — 25
▼B
3. As regards small-series vehicles, the number of vehicles registered,
sold or entered into service in the course of a single year shall not
exceed the number of units shown in Part A of Annex XII.
Article 27
Registration, sale and entry into service of end-of-series vehicles
1. Subject to the limits specified in Section B of Annex XII, and in

respect only of a limited period of time, Member States may register
and permit the sale or entry into service of vehicles conforming to a
type of vehicle whose EC type-approval is no longer valid.
The first subparagraph shall apply only to vehicles within the territory
of the Community which were covered by a valid EC type-approval at
the time of their production, but which had not been registered or put
into service before that EC type-approval lost its validity.
2. The option provided for in paragraph 1 shall be available, in the

case of complete vehicles, for a period of twelve months from the date
on which validity of the EC type-approval expired and, in the case of
completed vehicles, for a period of eighteen months from that date.
3. A manufacturer who wishes to benefit from the provisions of

paragraph 1 shall submit a request to the competent authority of each
Member State concerned by the entry into service of the vehicles in
question. The request must specify any technical or economic reasons
preventing those vehicles from complying with the new technical
requirements.
The Member States concerned shall decide, within three months of

receiving such a request, whether and in what number to permit the
registration of those vehicles within their territory.
4. Paragraphs 1, 2 and 3 shall apply mutatis mutandis to vehicles

which were covered by a national type-approval but which had not been
registered or put into service before that approval ceased to be valid, in
application of Article 45, owing to the compulsory enforcement of the
EC type-approval procedure.
5. Member States shall apply appropriate measures to ensure that the

number of vehicles to be registered or put into service in the framework
of the procedure set out in this Article is effectively monitored.
Article 28
Sale and entry into service of components and separate technical
units
1. Member States shall permit the sale or entry into service of

components or separate technical units if and only if they comply
with the requirements of the relevant regulatory acts and are properly
marked in accordance with Article 19.
02007L0046 — EN — 18.01.2018 — 021.001 — 26
▼B
2. Paragraph 1 shall not apply in the case of components or separate
technical units which are specifically constructed or designed for new
vehicles not covered by this Directive.
3. By way of derogation from paragraph 1, Member States may

permit the sale and entry into service of components or separate
technical units that have been exempted from one or more provisions
of a regulatory act in application of Article 20 or are intended for
mounting on vehicles covered by approvals granted under Articles 22,
23 or 24 that concern the component or separate technical unit in
question.
4. By way of derogation from paragraph 1, and unless otherwise

provided for in a regulatory act, Member States may permit the sale
and entry into service of components or separate technical units that are
intended for mounting on vehicles which, at the time of their entry into
service, were not required, by this Directive or by Directive 70/156/EEC
to be EC type-approved.
CHAPTER XII
SAFEGUARD CLAUSES
Article 29
Vehicles, systems, components or separate technical units in
compliance with this Directive
1. If a Member State finds that new vehicles, systems, components or

separate technical units, albeit in compliance with the applicable
requirements or properly marked, present a serious risk to road safety,
or seriously harm the environment or public health, that Member State
may, for a maximum period of six months, refuse to register such
vehicles or to permit the sale or entry into service in its territory of
such vehicles, components or separate technical units.
In such cases, the Member State concerned shall immediately notify the
manufacturer, the other Member States and the Commission
accordingly, stating the reasons on which its decision is based and, in
particular, whether it is the result of:
— shortcomings in the relevant regulatory acts, or
— incorrect application of the relevant requirements.
2. The Commission shall consult the parties concerned as soon as

possible and, in particular, the approval authority that granted the
type-approval in order to prepare the decision.
3. Where the measures referred to in paragraph 1 are attributed to

shortcomings in the relevant regulatory acts, the appropriate measures
shall be taken as follows:
— where separate directives or regulations listed in Part I of Annex IV

are concerned, the Commission shall amend them in accordance
with the regulatory procedure with scrutiny referred to in
Article 40(2),
02007L0046 — EN — 18.01.2018 — 021.001 — 27
▼B
— where UNECE Regulations are concerned, the Commission shall
propose the necessary draft amendments to the relevant UNECE
Regulations in accordance with the procedure applicable under the
Revised 1958 Agreement.
4. Where the measures referred to in paragraph 1 are attributed to

incorrect application of the relevant requirements, the Commission shall
take the appropriate measures to ensure compliance with such
requirements.
Article 30
Vehicles, systems, components or separate technical units not in
conformity with the approved type
1. If a Member State which has granted an EC type-approval finds

that new vehicles, systems, components or separate technical units
accompanied by a certificate of conformity or bearing an approval
mark do not conform to the type it has approved, it shall take the
necessary measures, including, where necessary, the withdrawal of
type-approval, to ensure that production vehicles, systems, components
or separate technical units, as the case may be, are brought into
conformity with the approved type. The approval authority of that
Member State shall advise the approval authorities of the other
Member States of the measures taken.
2. For the purposes of paragraph 1, deviations from the particulars in

the EC type-approval certificate or the information package shall be
deemed to constitute failure to conform to the approved type.
A vehicle shall not be deemed to deviate from the approved type where
tolerances are permitted by the relevant regulatory acts and those
tolerances are respected.
3. If a Member State demonstrates that new vehicles, components or

separate technical units accompanied by a certificate of conformity or
bearing an approval mark do not conform to the approved type, it may
ask the Member State which granted the EC type-approval to verify that
vehicles, systems, components or separate technical units in production
continue to conform to the approved type. On receipt of such a request,
the Member State concerned shall take the requisite action as soon as
possible and in any case within six months of the date of the request.
4. The approval authority shall request the Member State which

granted the system, component, separate technical unit or incomplete
vehicle type-approval to take the necessary action to ensure that vehicles
in production are brought back into conformity with the approved type
in the following cases:
(a) in relation to an EC vehicle type-approval, where the

non-conformity of a vehicle is attributable exclusively to the
non-conformity of a system, component or separate technical unit;
(b) in relation to a multi-stage type-approval, where the non-conformity

of a completed vehicle is attributable exclusively to the
non-conformity of a system, component or separate technical unit
being part of the incomplete vehicle, or of the incomplete vehicle
itself.
02007L0046 — EN — 18.01.2018 — 021.001 — 28
▼B
On receipt of such a request, the Member State concerned shall take the
requisite action, if necessary in conjunction with the Member State
making the request, as soon as possible and in any case within six
months of the date of the request. Where a failure to conform is estab
lished, the approval authority of the Member State which granted the
system, component or separate technical unit EC type-approval or the
approval of the incomplete vehicle shall take the measures set out in
paragraph 1.
5. The approval authorities shall inform each other within 20

working days of any withdrawal of EC type-approval and of the
reasons therefor.
6. If the Member State that granted EC type-approval disputes the

failure to conform notified to it, the Member States concerned shall
endeavour to settle the dispute. The Commission shall be kept
informed and, where necessary, shall hold appropriate consultations
with a view to reaching a settlement.
Article 31
Sale and entry into service of parts or equipment which are capable
of posing a significant risk to the correct functioning of essential
systems
1. Member States shall permit the sale, the offer for sale or entry into
service of parts or equipment which are capable of posing a significant
risk to the correct functioning of systems that are essential for the safety
of the vehicle or for its environmental performance, only if those parts
or equipment have been authorised by an approval authority in
accordance with paragraphs 5 to 10.
2. Parts or equipment subject to authorisation in accordance with

paragraph 1 shall be inserted in the list to be established in
Annex XIII. Such a decision shall be preceded by an evaluation
resulting in a report and strive for a fair balance between the
following elements:
(a) the existence of a serious risk to the safety or environmental

performance of vehicles fitted with the parts or equipment under
consideration; and
(b) the effect on consumers and manufacturers in the after-market of the

imposition under this Article of a possible authorisation requirement
on the parts or equipment under consideration.
3. Paragraph 1 shall not apply to original parts or equipment which

are covered by a system type-approval with respect to a vehicle and to
parts or equipment which are type-approved in accordance with the
provisions of one of the regulatory acts listed in Annex IV, except
where those approvals relate to aspects other than those covered in
paragraph 1. Paragraph 1 shall not apply to parts or equipment
exclusively produced for racing vehicles not intended for use on
public roads. If parts or equipment included in Annex XIII have a
dual use for racing and on the road, these parts or equipment may
not be sold or offered for sale to the general public for use in
on-road vehicles unless they comply with the requirements of this
Article.
02007L0046 — EN — 18.01.2018 — 021.001 — 29
▼B
Where appropriate, the Commission shall adopt provisions for iden
tifying the parts or equipment referred to in this paragraph.
4. The Commission shall, after consulting stakeholders, establish the

procedure and the requirements of the authorisation process referred to
in paragraph 1, and adopt the provisions for the subsequent updating of
the list established in Annex XIII. Those requirements shall include
prescriptions for safety, environmental protection and, where needed,
for testing standards. They may be based on the regulatory acts listed
in Annex IV, may be developed according to the relevant state of
safety, environmental and testing technology, or, if this is an appropriate
way of achieving the required safety or environmental objectives, may
consist of a comparison of the part or equipment with the environmental
or safety performance of the original vehicle, or of any of its parts, as
appropriate.
5. For the purposes of paragraph 1, the manufacturer of parts or

equipment shall submit to the approval authority a test report drafted
by a designated technical service which certifies that the parts or
equipment for which authorisation is sought comply with the
requirements referred to in paragraph 4. The manufacturer may
introduce only one application per type per part with only one
approval authority.
The application shall include details concerning the manufacturer of the

parts or equipment, the type, identification and part numbers of the parts
or equipment for which authorisation is sought, as well as the vehicle
manufacturer’s name, type of vehicle and, if appropriate, years of
construction or any other information permitting the identification of
the vehicle for which the fitting of such parts or equipment is intended.
When the approval authority is satisfied, taking account of the test

report and other evidence, that the parts or equipment in question
comply with the requirements referred to in paragraph 4, it shall issue
a certificate to the manufacturer without unjustified delay. This
certificate shall authorise the parts or equipment to be sold, offered
for sale or fitted to vehicles in the Community subject to the second
subparagraph of paragraph 9.
6. Each part or piece of equipment authorised in application of this

Article shall be appropriately marked.
The Commission shall establish marking and packaging requirements,

as well as the model and numbering system of the certificate referred to
in paragraph 5.
7. The measures referred to in paragraphs 2 to 6 shall be adopted in

accordance with the regulatory procedure with scrutiny referred to in
Article 40(2) as they are designed to amend non-essential elements of
this Directive, inter alia by supplementing it.
8. The manufacturer shall inform without delay the approval

authority that issued the certificate of any change affecting the
conditions under which it was delivered. That approval authority shall
decide whether the certificate has to be reviewed or reissued and
whether fresh tests are necessary.
The manufacturer shall be responsible for ensuring that the parts and
equipment are produced and continue to be produced under the
conditions under which the certificate was issued.
02007L0046 — EN — 18.01.2018 — 021.001 — 30
▼B
9. Before delivering any authorisation, the approval authority shall
verify the existence of satisfactory arrangements and procedures for
ensuring effective control of the conformity of production.
Where the approval authority finds that the conditions for issuing the
authorisation are no longer fulfilled, it shall request the manufacturer to
take the necessary measures to ensure that the parts or equipment are
brought back into conformity. If necessary, it shall withdraw the
authorisation.
10. Any disagreement between Member States in relation to the

certificates referred to in paragraph 5 shall be brought to the attention
of the Commission. It shall take appropriate measures, including, where
necessary, requiring the withdrawal of the authorisation, after having
consulted the Member States.
11. This Article shall not be applicable to a part or piece of

equipment before it is listed in Annex XIII. For any entry or group
of entries in Annex XIII a reasonable transitional period shall be fixed
to allow the manufacturer of the part or equipment to apply for and
obtain an authorisation. At the same time a date may be fixed, where
appropriate, to exclude parts and equipment designed for vehicles
type-approved before that date from the application of this Article.
12. As long as a decision as to whether or not a part or piece of

equipment is to be included in the list referred to in paragraph 1 has not
been taken, Member States may maintain national provisions dealing
with parts or equipment which are capable of posing a significant risk to
the correct functioning of systems that are essential for the safety of the
vehicle or its environmental performance.
Once such a decision in this regard has been taken, the national
provisions dealing with the parts or equipment in question shall cease
to be valid.
13. As from 29 October 2007, Member States shall not adopt new
provisions dealing with parts and equipment which can affect the correct
functioning of systems that are essential for the safety of the vehicle or
its environmental performance.
Article 32
Recall of vehicles
1. Where a manufacturer who has been granted an EC vehicle

type-approval is obliged, in application of the provisions of a regulatory
act or of Directive 2001/95/EC, to recall vehicles already sold,
registered or put into service because one or more systems, components
or separate technical units fitted to the vehicle, whether or not duly
approved in accordance with this Directive, presents a serious risk to
road safety, public health or environmental protection, he shall
immediately inform the approval authority that granted the vehicle
approval thereof.
02007L0046 — EN — 18.01.2018 — 021.001 — 31
▼B
2. The manufacturer shall propose to the approval authority a set of
appropriate remedies to neutralise the risk referred to in paragraph 1.
The approval authority shall communicate the proposed measures to the
authorities of the other Member States without delay.
The competent authorities shall ensure that the measures are effectively
implemented in their respective territories.
3. If the measures are considered to be insufficient by the authorities

concerned or have not been implemented quickly enough, they shall
inform the approval authority that granted the EC vehicle
type-approval without delay.
The approval authority shall then inform the manufacturer. If the

approval authority which granted the EC type-approval is itself not
satisfied with the measures of the manufacturer, it shall take all
protective measures required, including the withdrawal of the EC
vehicle type-approval where the manufacturer does not propose and
implement effective corrective measures. In case of withdrawal of the
EC vehicle type-approval, the concerned approval authority shall notify
the manufacturer, the approval authorities of the other Member States
and the Commission by registered letter or equivalent electronic means
within 20 working days.
4. This Article shall also apply to parts that are not subject to any
requirement under a regulatory act.
Article 33
Notification of decisions and remedies available
All decisions taken pursuant to the provisions adopted in implemen

tation of this Directive and all decisions refusing or withdrawing EC
type-approval, or refusing registration or prohibiting sales, shall state in
detail the reasons on which they are based.
Any such decision shall be notified to the party concerned who shall, at
the same time, be informed of the remedies available to him under the
laws in force in the Member State concerned and of the time limits
allowed for the exercise of such remedies.
CHAPTER XIII
INTERNATIONAL REGULATIONS
Article 34
UNECE Regulations required for EC type-approval
1. UNECE Regulations to which the Community has acceded and

which are listed in Part I of Annex IV and in Annex XI are part of the
EC type-approval of a vehicle in the same way as the separate directives
or regulations. They shall apply to the categories of vehicles listed in
the relevant columns in the table of Part I of Annex IV and Annex XI.
02007L0046 — EN — 18.01.2018 — 021.001 — 32
▼B
2. When the Community has decided to apply on a compulsory basis
a UNECE Regulation for the purpose of EC vehicle type-approval in
accordance with Article 4(4) of Decision 97/836/EC, the annexes to this
Directive shall be amended as appropriate in accordance with the regu
latory procedure with scrutiny referred to in Article 40(2) of this
Directive. The act amending the Annexes to this Directive shall also
specify the dates of compulsory application of the UNECE Regulation
or of its amendments. Member States shall repeal or adapt any national
legislation that is incompatible with the UNECE Regulation in question.
Where such a UNECE Regulation replaces an existing separate directive

or regulation, the relevant entry in Part I of Annex IV and in Annex XI
shall be replaced by the number of the UNECE Regulation and the
corresponding entry in Part II of Annex IV shall be deleted in
accordance with the same procedure.
3. In the cases referred to in the second subparagraph of paragraph 2,

the separate directive or regulation replaced by the UNECE Regulation
shall be repealed in accordance with the regulatory procedure with
scrutiny referred to in Article 40(2).
Where a separate directive is repealed, Member States shall repeal any

national legislation that was adopted for the transposition of that
directive.
4. Direct references may be made in this Directive or in the separate

directives or regulations to international standards and regulations
without reproducing them in the Community legal framework.
Article 35
Equivalence of UNECE Regulations with directives or regulations
1. The UNECE Regulations listed in Part II of Annex IV are

recognised as being equivalent to the corresponding separate directives
or regulations in as much as they share the same scope and subject
matter.
The approval authorities of the Member States shall accept approvals

granted in accordance with those UNECE Regulations and, where
applicable, the pertaining approval marks, in lieu of the corresponding
approvals and approval marks granted in accordance with the equivalent
separate directive or regulation.
2. Where the Community has decided to apply, for the purposes of

paragraph 1, a new UNECE Regulation or a UNECE Regulation as
amended, Part II of Annex IV shall be amended as appropriate. These
measures, designed to amend non-essential elements of this Directive
shall be adopted in accordance with the regulatory procedure with
scrutiny referred to in Article 40(2).
02007L0046 — EN — 18.01.2018 — 021.001 — 33
▼B
Article 36
Equivalence with other regulations
The Council may, acting by qualified majority on a proposal from the

Commission, recognise the equivalence between the conditions or
provisions for EC type-approval of systems, components and separate
technical units established by this Directive and the procedures estab
lished by international regulations or regulations of third countries, in
the framework of multilateral or bilateral agreements between the
Community and third countries.
CHAPTER XIV
PROVISION OF TECHNICAL INFORMATION
Article 37
Information intended for users
1. The manufacturer may not supply any technical information

related to the particulars provided for in this Directive or in the regu
latory acts listed in Annex IV which diverges from the particulars
approved by the approval authority.
2. Where a regulatory act makes specific provisions for so doing, the

manufacturer shall make available to users all relevant information and
necessary instructions describing any special conditions or restrictions
attaching to the use of a vehicle, a component or a separate technical
unit.
That information shall be supplied in the official languages of the

Community. It shall be provided, in agreement with the approval
authority, in an appropriate supporting document, such as the owner’s
manual or the maintenance book.
Article 38
Information intended for manufacturers of components or separate
technical units
1. The vehicle manufacturer shall make available to the manu

facturers of components or separate technical units all those particulars
including, as the case may be, drawings specifically listed in the annex
or appendix to a regulatory act that are necessary for EC type-approval
of components or separate technical units, or necessary to obtain an
authorisation under Article 31.
The vehicle manufacturer may impose a binding agreement on the

manufacturers of components or separate technical units to protect the
confidentiality of any information that is not in the public domain,
including what is related to intellectual property rights.
2. The manufacturer of components or separate technical units, in his

capacity as the holder of an EC type-approval certificate which, in
accordance with Article 10(4), includes restrictions on use or special
mounting conditions or both, shall provide all the detailed information
thereon to the vehicle manufacturer.
02007L0046 — EN — 18.01.2018 — 021.001 — 34
▼B
Where a regulatory act makes provision for so doing, the manufacturer
of components or separate technical units shall provide, together with
the components or separate technical units produced, instructions
regarding restrictions on use or special mounting conditions or both.
CHAPTER XV
IMPLEMENTATION MEASURES AND AMENDMENTS
Article 39
Implementation measures and amendments to this Directive and the
separate directives and regulations
1. The Commission shall adopt the measures necessary for the imple
mentation of each separate directive or regulation in compliance with
the rules laid down in each directive or regulation concerned.
2. The Commission shall adopt amendments to the annexes to this

Directive or to the provisions of the separate directives or regulations
listed in Part I of Annex IV, which are necessary to adapt them to the
development of scientific and technical knowledge or to the specific
needs of persons with disabilities.
3. The Commission shall adopt amendments to this Directive which

are necessary to lay down technical requirements for small series
vehicles, vehicles approved under the individual approval procedure
and special purpose vehicles.
4. When the Commission becomes aware of serious risks to road

users or to the environment, which require urgent measures, it may
amend the provisions of the separate directives or regulations listed in
Part I of Annex IV.
5. The Commission shall adopt amendments which are necessary in

the interest of good administration and in particular those needed to
ensure the coherence of the separate directives or regulations listed in
Part I of Annex IV either amongst themselves or with other pieces of
Community law.
6. When, in application of Decision 97/836/EC, new UNECE Regu

lations or amendments to existing UNECE Regulations to which the
Community has acceded are adopted, the Commission shall amend the
annexes to this Directive accordingly.
7. Each new separate directive or regulation shall introduce the

appropriate amendments to the annexes to this Directive.
8. The annexes to this Directive may be amended by means of

regulations.
9. Measures referred to in this Article shall be adopted in accordance

with the regulatory procedure with scrutiny referred to in Article 40(2)
as they are designed to amend non-essential elements of this Directive
or of the separate directives and regulations, inter alia by supplementing
them.
02007L0046 — EN — 18.01.2018 — 021.001 — 35
▼B
Article 40
Committee
1. The Commission shall be assisted by a committee referred to as

the ‘Technical Committee — Motor Vehicles’ (TCMV).
2. Where reference is made to this paragraph, Article 5a(1) to (4),

and Article 7 of Decision 1999/468/EC shall apply, having regard to the
provisions of Article 8 thereof.
3. Where reference is made to this paragraph, Articles 5 and 7 of

Decision 1999/468/EC shall apply, having regard to the provisions of
Article 8 thereof.
The period referred to in Article 5(6) of Decision 1999/468/EC shall be

set at three months.
CHAPTER XVI
DESIGNATION AND NOTIFICATION OF TECHNICAL SERVICES
Article 41
Designation of technical services
1. When a Member State designates a technical service, the latter

shall comply with the provisions of this Directive.
2. The technical services shall carry out themselves or supervise the

tests required for approval or inspections specified in this Directive or in
a regulatory act listed in Annex IV, except where alternative procedures
are specifically permitted. They may not conduct tests or inspections for
which they have not been duly designated.
3. The technical services shall fall into one or more of the four
following categories of activities, depending on their field of
competence:
(a) category A, technical services which carry out in their own facilities
the tests referred to in this Directive and in the regulatory acts listed
in Annex IV;
(b) category B, technical services which supervise the tests referred to

in this Directive and in the regulatory acts listed in Annex IV,
performed in the manufacturer’s facilities or in the facilities of a
third party;
(c) category C, technical services which assess and monitor on a

regular basis the manufacturer’s procedures for controlling
conformity of production;
(d) category D, technical services which supervise or perform tests or

inspections in the framework of the surveillance of conformity of
production.
4. Technical services shall demonstrate appropriate skills, specific

technical knowledge and proven experience in the specific fields
covered by this Directive and the regulatory acts listed in Annex IV.
02007L0046 — EN — 18.01.2018 — 021.001 — 36
▼B
In addition, technical services shall comply with the standards listed in
Appendix 1 to Annex V which are relevant for the activities they carry
out. However, this requirement does not apply for the purposes of the
last stage of a multi-stage type-approval procedure as referred to in
Article 25(1).
5. An approval authority may act as a technical service for one or

more of the activities referred to in paragraph 3.
6. A manufacturer or a subcontracting party acting on his behalf may

be designated as a technical service for category A activities with regard
to the regulatory acts listed in Annex XV.
The Commission shall amend the list of these regulatory acts where
necessary in accordance with the regulatory procedure with scrutiny
referred to in Article 40(2).
7. The entities referred to in paragraphs 5 and 6 shall comply with

the provisions of this Article.
8. Technical services, other than those designated in accordance with

paragraph 6, of a third country may be notified for the purposes of
Article 43 only in the framework of a bilateral agreement between the
Community and the third country in question.
Article 42
Assessment of the skills of the technical services
1. The skills referred to in Article 41 shall be demonstrated by an

assessment report established by a competent authority. This may
include a certificate of accreditation issued by an accreditation body.
2. The assessment on which the report referred to in paragraph 1 is

based shall be conducted in accordance with the provisions of Appendix
2 to Annex V.
The assessment report shall be reviewed after a maximum period of

three years.
3. The assessment report shall be communicated to the Commission

upon request.
4. The approval authority which acts as a technical service shall

demonstrate compliance through documentary evidence.
This includes an assessment conducted by auditors independent of the

activity being assessed. Such auditors may be from within the same
organisation provided that they are managed autonomously from
personnel undertaking the assessed activity.
5. A manufacturer or a subcontracting party acting on his behalf,

designated as a technical service, shall comply with the relevant
provisions of this Article.
02007L0046 — EN — 18.01.2018 — 021.001 — 37
▼B
Article 43
Procedures for notification
1. Member States shall notify to the Commission the name, the

address including electronic address, the responsible persons and the
category of activities with respect to each designated technical
service. They shall notify it of any subsequent modifications thereto.
The notification act shall state in respect of which regulatory acts the
technical services have been designated.
2. A technical service may conduct the activities described in

Article 41 for the purposes of type-approval only if it has been
notified beforehand to the Commission.
3. The same technical service may be designated and notified by

several Member States irrespective of the category of activities which
it conducts.
4. Where a specific organisation or competent body, the activity of

which is not included in those referred to in Article 41, needs to be
designated in application of a regulatory act, the notification shall be
made in accordance with the provisions of this Article.
5. The Commission shall publish a list and details regarding the

approval authorities and technical services on its web-site.
CHAPTER XVII
FINAL PROVISIONS
Article 44
Transitional provisions
1. Pending the necessary amendments to this Directive in order to

include vehicles not yet covered or to complete the administrative and
technical provisions regarding type-approval of vehicles other than M1
produced in small series, and to lay down harmonised administrative
and technical provisions regarding the individual approval procedure,
and pending expiry of the transitional periods provided for in Article 45,
Member States shall continue to grant national approvals for those
vehicles, provided that such approvals are based on the harmonised
technical requirements laid down in this Directive.
2. On application by the manufacturer or, in the case of individual

approval, by the owner of the vehicle and on submission of the
information required, the Member State concerned shall complete and
issue the type-approval certificate or the individual approval certificate
as appropriate. The certificate shall be issued to the applicant.
With respect to vehicles of the same type, other Member States shall
accept a certified true copy as proof that the requisite tests have been
carried out.
02007L0046 — EN — 18.01.2018 — 021.001 — 38
▼B
3. Where a particular vehicle covered by an individual approval has
to be registered in another Member State, that Member State may
require, from the approval authority that has issued the individual
approval, any additional information stating in detail the nature of the
technical requirements satisfied by that particular vehicle.
4. Pending the harmonisation of registration and taxation systems of

the Member States in relation to vehicles covered by this Directive,
Member States may use national codes in order to facilitate registration
and taxation in their territory. For this purpose, Member States may
subdivide the versions shown in Part II of Annex III, provided that
the particulars used for the subdivision are expressly stated in the
information package or can be derived from it by a simple calculation.
Article 45
Application dates for EC type-approval
1. As regards EC type-approval, Member States shall grant EC

approval to new types of vehicle from the dates specified in
Annex XIX.
2. On application by the manufacturer, Member States may grant EC

approval to new types of vehicle from 29 April 2009.
3. Until the dates specified in the fourth column of the table set out
in Annex XIX, Article 26(1) shall not apply to new vehicles for which a
national approval has been granted before the dates specified in the third
column thereof or for which there has been no approval.
4. At the request of the manufacturer, and until the dates specified in

column 3 of rows 6 and 9 of the table set out in Annex XIX, Member
States shall continue to grant national type-approvals as an alternative to
EC vehicle type-approval for vehicles of category M2 or M3 on the
condition that those vehicles and their systems, components and
separate technical units have been type-approved in accordance with
the regulatory acts listed in Part I of Annex IV to this Directive.
5. This Directive shall not invalidate any EC type-approval granted

to vehicles of category M1 before 29 April 2009 nor prevent the
extension of such approvals.
6. As regards the EC approval of new types of systems, components

or separate technical units, Member States shall apply this Directive
from 29 April 2009.
This Directive shall not invalidate any EC type-approval granted for

systems, components or separate technical units before 29 April 2009
nor prevent the extension of such approvals.
02007L0046 — EN — 18.01.2018 — 021.001 — 39
▼B
Article 46
Penalties
Member States shall determine the penalties applicable for infringement

of the provisions of this Directive, and in particular of the prohibitions
contained in or resulting from Article 31, and of the regulatory acts
listed in Part I of Annex IV and shall take all necessary measures for
their implementation. The penalties determined shall be effective,
proportionate and dissuasive. Member States shall notify these
provisions to the Commission no later than 29 April 2009 and shall
notify any subsequent modifications thereof as soon as possible.
Article 47
Assessment
1. No later than 29 April 2011, Member States shall inform the

Commission of the application of the type-approval procedures laid
down in this Directive and, in particular, of the application of the
multi-stage process. Where appropriate, the Commission shall propose
the amendments deemed necessary to improve the type-approval
process.
2. On the basis of the information supplied under paragraph 1, the

Commission shall report to the European Parliament and the Council on
the application of this Directive no later than 29 October 2011. If
appropriate, the Commission may propose the postponement of the
application dates referred to in Article 45.
Article 48
Transposition
1. Member States shall adopt and publish, before 29 April 2009, the
laws, regulations and administrative provisions necessary to comply
with the substantive amendments of this Directive. They shall
forthwith communicate to the Commission the text of those provisions.
They shall apply those provisions from 29 April 2009.
When Member States adopt those provisions, they shall contain a

reference to this Directive or be accompanied by such a reference on
the occasion of their official publication. They shall also include a
statement that references in existing laws, regulations and administrative
provisions to the Directive repealed by this Directive shall be construed
as references to this Directive. Member States shall determine how such
reference is to be made and how that statement is to be formulated.
2. Member States shall communicate to the Commission the text of

the main provisions of national law which they adopt in the field
covered by this Directive.
02007L0046 — EN — 18.01.2018 — 021.001 — 40
▼B
Article 49
Repeal
Directive 70/156/EEC is repealed with effect from 29 April 2009,

without prejudice to the obligations of the Member States relating to
the time-limits for transposition into national law and application of the
directives set out in Part B of Annex XX.
References to the repealed Directive shall be construed as references to

this Directive and shall be read in accordance with the correlation table
set out in Annex XXI.
Article 50
Entry into force
This Directive shall enter into force on the 20th day following its
publication in the Official Journal of the European Union.
Article 51
Addressees
This Directive is addressed to the Member States.

02007L0046 — EN — 18.01.2018 — 021.001 — 41
▼B
LIST OF ANNEXES
Annex I Complete list of information for the purpose of EC type-

approval of vehicles, components or separate technical units
Annex II General definitions, criteria for vehicle categorisation, vehicle

types and types of bodywork
Appendix 1: Procedure for checking whether a vehicle can
be categorised as off-road vehicle
Appendix 2: Digits used to supplement the codes to be
used for various kinds of bodywork
Annex III Information document for the purpose of EC type-approval of

vehicles
Annex IV Requirements for the purpose of EC type-approval of vehicles
Appendix 1: Regulatory acts for EC type-approval of

vehicles produced in small series pursuant to
Article 22
Appendix 2: Requirements for the approval pursuant to

Article 24 of complete vehicles belonging to
category M1 and N1, produced in large series
in or for third countries
Annex V Procedures to be followed with respect to EC type-approval

Appendix 1: Standards with which the entities referred to
in Article 41 have to comply
Appendix 2: Procedure for the assessment of the technical
services
Appendix 3: General requirements concerning the format
of the test reports
Annex VI Models of the type-approval certificate

Appendix: List of regulatory acts to which the type of
vehicle complies
Annex VII EC type-approval certificate numbering system

Appendix: EC component and separate technical unit
type-approval mark
Annex VIII Test results
Annex IX EC certificate of conformity
Annex X Conformity of production procedures

02007L0046 — EN — 18.01.2018 — 021.001 — 42
▼B
Annex XI Nature of and provisions for the EC type-approval of special
purpose vehicles
Appendix 1: Motor-Caravans, Ambulances and Hearses
Appendix 2: Armoured Vehicles
Appendix 3: Wheel-chair Accessible Vehicles
Appendix 4: Other Special Purpose Vehicles (including

special group, multi-equipment carrier and
trailer Caravans)
Appendix 5: Mobile Cranes
Appendix 6: Exceptional load transport vehicles
Annex XII Small series and end-of-series limits
Annex XIII List of parts or equipment which are capable of posing a

significant risk to the correct functioning of systems that are
essential for the safety of the vehicle or its environmental
performance, their performance requirements, appropriate test
procedures, marking and packaging provisions
Annex XIV List of EC type-approvals issued pursuant to regulatory acts
Annex XV Regulatory acts for which a manufacturer may be designated

as technical service
Appendix: Designation of a manufacturer as technical

service
Annex XVI Specific conditions required from virtual testing methods and
regulatory acts for which virtual testing methods may be used
by a manufacturer or a technical service
Appendix 1: General conditions required from virtual

testing methods
Appendix 2: Specific conditions concerning virtual testing

methods
Appendix 3: Validation process
Annex XVII Procedures to be followed during multi-stage EC

type-approval
Appendix: Model of the manufacturer’s additional plate
Annex XIX Timetable for the enforcement of this Directive in respect of

type-approval
Annex XX Time-limits for the transposition of repealed directives into

national law
Annex XXI Correlation table

02007L0046 — EN — 18.01.2018 — 021.001 — 43
▼M1
ANNEX I
▼M26
COMPLETE LIST OF INFORMATION FOR THE PURPOSE OF EC
TYPE-APPROVAL OF VEHICLES, COMPONENTS OR SEPARATE
TECHNICAL UNITS (a)
▼M1
All information documents in this directive and in separate directives or regu

lations shall consist only of extracts from, and adhere to the item numbering
system of, this total list.
The following information shall be supplied in triplicate and include a list of

contents. Any drawings shall be supplied in appropriate scale and in sufficient
detail on size A4 or on a folder of A4 format. Photographs, if any, shall show
sufficient detail.
If the systems, components or separate technical units referred to in this annex

have electronic controls, information concerning their performance shall be
supplied.
0. GENERAL
0.1. Make (trade name of manufacturer): … . . . . . . . . . . . . . . . . . . . . .
0.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2.0.1. Chassis: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2.0.2. Bodywork/complete vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2.1. Commercial name(s) (if available): … . . . . . . . . . . . . . . . . . . . . . . .
▼M24
0.2.2. For multi-stage approved vehicles, type-approval information
of the base/previous stage vehicle (list the information for each
stage. This can be done with a matrix)
Type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variant(s): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Version(s): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type-approval number, including extension number … . . . . . .
▼M26
0.3. Means of identification of type, if marked on the vehicle/
component/separate technical unit (1) (b): …. . . . . . . . . . . . . . . . . .
▼M1
0.3.0.1. Chassis: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.3.1. Location of that marking: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.3.1.1. Chassis: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.4. Category of vehicle (c): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.4.1. Classification(s) according to the dangerous goods which the

vehicle is intended to transport: … . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
0.5. Company name and address of manufacturer: … . . . . . . . . . . . .
▼M24
0.5.1. For multi-stage approved vehicles, company name and address
of the manufacturer of the base/previous stage(s) vehicle: …
02007L0046 — EN — 18.01.2018 — 021.001 — 44
▼M1
0.6. Location and method of attachment of statutory plates and
location of vehicle identification number: … . . . . . . . . . . . . . . . .
0.6.1. On the chassis: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.6.2. On the bodywork: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.7. (Not attributed)
0.8. Name(s) and address(es) of assembly plant(s): … . . . . . . . . . . .
0.9. Name and address of the manufacturer's representative (if any):

… ..........................................................
▼M26
1. GENERAL CONSTRUCTION CHARACTERISTICS
1.1. Photographs and/or drawings of a representative vehicle/
component/separate technical unit (l): . . . . . . . . . . . . . . . . . . . . . . .
▼M1
1.2. Dimensional drawing of the whole vehicle: … . . . . . . . . . . . . . .
1.3. Number of axles and wheels: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1. Number and position of axles with twin wheels: … . . . . . . . . .
1.3.2. Number and position of steered axles: … . . . . . . . . . . . . . . . . . . .
1.3.3. Powered axles (number, position, interconnection): … . . . . . . .
1.4. Chassis (if any) (overall drawing): … . . . . . . . . . . . . . . . . . . . . . . .
1.5. Material used for the side-members (d): … . . . . . . . . . . . . . . . . . .
1.6. Position and arrangement of the engine: … . . . . . . . . . . . . . . . . .
1.7. Driving cab (forward control or bonneted) (e): … . . . . . . . . . . . .
1.8. Hand of drive: left/right (1).
1.8.1. Vehicle is equipped to be driven in right/left (1) hand traffic.
▼M15
1.9. Specify if the towing vehicle is intended to tow semi-trailers or
other trailers and, if the trailer is a semi-, drawbar-,
centre-axle- or rigid drawbar trailer: …. . . . . . . . . . . . . . . . . . . . . .
1.10. Specify if the vehicle is specially designed for the

controlled-temperature carriage of goods: … . . . . . . . . . . . . . . . . .
2. MASSES AND DIMENSIONS (f) (g) (7)

(in kg and mm) (Refer to drawing where applicable)
▼M1
2.1. Wheelbase(s) (fully loaded) (g1):
2.1.1. Two-axle vehicles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
2.1.2. Vehicles with three or more axles
2.1.2.1. Axle spacing between consecutive axles going from the

foremost to the rearmost axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2.2. Total axle spacing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
2.2. Fifth wheel
2.2.1. In the case of semi-trailers
02007L0046 — EN — 18.01.2018 — 021.001 — 45
▼M1
2.2.1.1. Distance between the axis of the fifth wheel kingpin and the
rearmost end of the semi-trailer: … . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1.2. Maximum distance between the axis of the fifth wheel kingpin
and any point on the front of the semi-trailer: … . . . . . . . . . . .
2.2.1.3. Semi-trailer special wheelbase (as defined in Section 7.6.1.2 of

Annex I to Directive 97/27/EC): … . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.2. In the case of semi-trailer towing vehicles
2.2.2.1. Fifth wheel lead (maximum and minimum; indicate the

permissible values in the case of an incomplete vehicle) (g2):
… ..........................................................
2.2.2.2. Maximum height of the fifth wheel (standardised) (g3): … . . .
2.3. Axle track(s) and width(s)

2.3.1. Track of each steered axle (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2. Track of all other axles (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.3. Width of the widest rear axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.4. Width of the foremost axle (measured at the outermost part of

the tyres excluding the bulging of the tyres close to the
ground): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4. Range of vehicle dimensions (overall)

2.4.1. For chassis without bodywork
2.4.1.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.1. Maximum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.2. Minimum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.3. In the case of trailers, maximum permissible drawbar

length (g6): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.1. Maximum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.2. Minimum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.3. Height (in running order) (g8) (for suspensions adjustable for
height, indicate normal running position): … . . . . . . . . . . . . . . . .
2.4.1.4. Front overhang (g9): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.4.1. Approach angle (g10): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees.
2.4.1.5. Rear overhang (g11): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.5.1. Departure angle (g12): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees.
2.4.1.5.2. Minimum and maximum permissible overhang of the coupling

point (g13): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.6. Ground clearance (as defined in point 4.5 of Section A of

Annex II)
2.4.1.6.1. Between the axles: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.6.2. Under the front axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.6.3. Under the rear axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.7. Ramp angle (g14): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees.

02007L0046 — EN — 18.01.2018 — 021.001 — 46
▼M1
2.4.1.8. Extreme permissible positions of the centre of gravity of the
body and/or interior fittings and/or equipment and/or payload:
… ..........................................................
2.4.2. For chassis with bodywork
2.4.2.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.1.1. Length of the loading area: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.1.2. In the case of trailers, maximum permissible drawbar

length (g6): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.2.1. Thickness of the walls (in the case of vehicles designed for
controlled-temperature carriage of goods): … . . . . . . . . . . . . . . . .
height, indicate normal running position): … . . . . . . . . . . . . . . . .
2.4.2.4. Front overhang (g9): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.4.1. Approach angle (g10): …… . . . . . . . . . . . . . . . . . . . . . . . . . degrees.
2.4.2.5. Rear overhang (g11): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.5.1. Departure angle (g12): …… . . . . . . . . . . . . . . . . . . . . . . . . . degrees.
2.4.2.5.2. Minimum and maximum permissible overhang of the coupling

point (g13): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.6. Ground clearance (as defined in point 4.5 of Section A of

Annex II)
2.4.2.6.1. Between the axles: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.6.2. Under the front axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.6.3. Under the rear axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.7. Ramp angle (g14): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . degrees.
2.4.2.8. Extreme permissible positions of the centre of gravity of the

payload (in the case of non-uniform load): … . . . . . . . . . . . . . . .
2.4.2.9. Position of centre of gravity of the vehicle (M2 and M3) at its
technically permissible maximum laden mass in the longi
tudinal, transverse and vertical directions: … . . . . . . . . . . . . . . . .
2.4.3. For bodywork approved without chassis (vehicles M2 and M3)
2.4.3.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.3.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.3.3. Nominal height (in running order) (g8) on intended chassis

type(s) (for suspensions adjustable for height, indicate
normal running position): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
2.5. Minimum mass on the steering axle(s) for incomplete
vehicles:
… ..........................................................
2.6. Mass in running order (h)

(a) minimum and maximum for each variant: … . . . . . . . . . . . .
(b) mass of each version (a matrix must be provided): … . . .
▼M27
2.6.1. Distribution of this mass among the axles and, in the case of
a semi-trailer, a rigid drawbar trailer or a centre-axle trailer, the
mass on the coupling:
02007L0046 — EN — 18.01.2018 — 021.001 — 47
▼M27
(a) minimum and maximum for each variant: … . . . . . . . . . . . .
(b) mass of each version (a matrix must be provided): … . . .
▼M15
2.6.2. Mass of the optional equipment (see the definition set out in
point (5) of Article 2 of Commission Regulation (EU)
No 1230/2012 (*)): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
2.7. Minimum mass of the completed vehicle as stated by the
manufacturer, in the case of an incomplete vehicle: … . . . . . .
a semi-trailer or centre-axle trailer, load on the coupling point:
… ..........................................................
2.8. Technically permissible maximum laden mass stated by the

manufacturer (i) (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
a semi-trailer or centre-axle trailer, load on the coupling
point (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9. Technically permissible maximum mass on each axle: … .
▼M15
2.10. Technically permissible mass on each group of axles: … .
2.11. Technically permissible maximum towable mass of the

towing vehicle
in case of:
▼M1
2.11.1. Drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.2. Semi-trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.3. Centre-axle trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.3.1. Maximum ratio of the coupling overhang (j) to the wheel base:
… ..........................................................
2.11.3.2. Maximum V-value: ……. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kN.
▼M15
2.11.4. Rigid drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.5. Technically permissible maximum laden mass of the

combination (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
2.11.6. Maximum mass of unbraked trailer: …. . . . . . . . . . . . . . . . . . . . . .
▼M15
2.12. Technically permissible maximum mass at the coupling
point:
2.12.1. Of a towing vehicle: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.12.2. Of a semi-trailer, a centre-axle trailer or a rigid drawbar trailer:

… ..........................................................
▼M1
2.12.3. Maximum permissible mass of the coupling device (if not
fitted by the manufacturer): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.13. Rear swing-out (Section 7.6.2. and 7.6.3. of Annex I to

Directive 97/27/EC): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.14. Engine power/maximum mass ratio: …… . . . . . . . . . kW/kg.

02007L0046 — EN — 18.01.2018 — 021.001 — 48
▼M1
2.14.1. Engine power/technically permissible maximum laden mass of
the combination ratio (Section 7.10 of Annex I to Directive
97/27/EC): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kW/kg.
2.15. Hill-starting ability (solo vehicle) (4): …… . . . . . . . . . . . . . %.
▼M15
2.16. Registration/in service maximum permissible masses
(optional)
2.16.1. Registration/in service maximum permissible laden mass: …
2.16.2. Registration/in service maximum permissible mass on each

axle and, in the case of a semi-trailer or centre-axle trailer,
intended load on the coupling point stated by the manufacturer
if lower than the technically permissible maximum mass on
the coupling point: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

group of axles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.16.4. Registration/in service maximum permissible towable mass: …
2.16.5. Registration/in service maximum permissible mass of the

combination: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M16
2.17. Vehicle submitted to multi-stage type-approval (only in the
case of incomplete or completed vehicles of category N1
within the scope of Regulation (EC) No 715/2007: yes/no (1)
2.17.1. Mass of the base vehicle in running order: …. . . . . . . . . . . kg.
2.17.2. Default added mass, calculated in accordance with Section 5 of

Annex XII to Regulation (EC) No 692/2008: … . . . . . . . . kg.
▼M27
3. PROPULSION ENERGY CONVERTER (k)
3.1. Manufacturer of the propulsion energy converter(s): … . .
3.1.1. Manufacturer's code (as marked on the propulsion energy
converter or other means of identification): … . . . . . . . . . . . . . .
▼M1
3.1.2. Approval number (if appropriate) including fuel identification
marking: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(heavy-duty vehicles only)
3.2. Internal combustion engine

3.2.1. Specific engine information
▼M21
3.2.1.1. Working principle: positive ignition/compression ignition/dual-
fuel (1)
Cycle: four stroke/two stroke/rotary (1)
3.2.1.1.1. Type of dual-fuel engine: Type 1A/Type 1B/Type 2A/Type

2B/Type 3B (1) (x1)
3.2.1.1.2. Gas energy ratio over the hot part of the WHTC test-cycle:
… ....................................................... %
▼M1
3.2.1.2. Number and arrangement of cylinders: … . . . . . . . . . . . . . . . . . . .
3.2.1.2.1. Bore (l): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm
3.2.1.2.2. Stroke (l): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm

02007L0046 — EN — 18.01.2018 — 021.001 — 49
▼M1
3.2.1.2.3. Firing order: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1.3. Engine capacity (m): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cm3
3.2.1.4. Volumetric compression ratio (2): …. . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1.5. Drawings of combustion chamber, piston crown and, in the

case of positive ignition engines, piston rings: … . . . . . . . . . . .
3.2.1.6. Normal engine idling speed (2): …… . . . . . . . . . . . . . . . . . . min-1
3.2.1.6.1. High engine idling speed (2): …… . . . . . . . . . . . . . . . . . . . . min-1
▼M21
3.2.1.6.2. Idle on diesel: yes/no (1) (x1)
▼M1
3.2.1.7. Carbon monoxide content by volume in the exhaust gas with
the engine idling (2): …… . % as stated by the manufacturer
(positive ignition engines only)
▼M27
3.2.1.8. Rated engine power (n): … . . . kW at …. . . . min–1 (manu
facturer's declared value)
▼M1
3.2.1.9. Maximum permitted engine speed as prescribed by the manu
facturer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . min-1
3.2.1.10. Maximum net torque (n): … Nm at … min-1 (manufacturer's

declared value)
▼M11
3.2.1.11. (Euro VI only) Manufacturer references of the Documentation
package required by Articles 5, 7 and 9 of Regulation (EU)
No 582/2011 enabling the approval authority to evaluate the
emission control strategies and the Systems on-board the
engine to ensure the correct operation of NOx control measures
▼M1
3.2.2. Fuel
▼M21
3.2.2.1. Light-duty vehicles: Diesel/Petrol/LPG/NG or Biomethane/
Ethanol (E 85)/Biodiesel/Hydrogen/H2NG (1) (6)
▼M27
3.2.2.1.1. RON, unleaded: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M21
3.2.2.2. Heavy duty vehicles Diesel/Petrol/LPG/NG-H/NG-L/NG-
HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20/ (1) (6)
▼M11
3.2.2.2.1. (Euro VI only) Fuels compatible with use by the engine
declared by the manufacturer in accordance with Section
1.1.2 of Annex I to Regulation (EU) No 582/2011 (as
applicable)
▼M1
3.2.2.3. Fuel tank inlet: restricted orifice/label (1)
3.2.2.4. Vehicle fuel type: Mono fuel, Bi fuel, Flex fuel (1)
3.2.2.5. Maximum amount of biofuel acceptable in fuel (manufacturer's

declared value): …. . . . . . . . . . . . . . . . . . . . . . . . . . . % by volume
02007L0046 — EN — 18.01.2018 — 021.001 — 50
▼M1
3.2.3. Fuel tank(s)
3.2.3.1. Service fuel tank(s)
3.2.3.1.1. Number and capacity of each tank: … . . . . . . . . . . . . . . . . . . . . . .
3.2.3.1.1.1. Material: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3.1.2. Drawing and technical description of the tank(s) with all

connections and all lines of the breathing and venting
system, locks, valves, fastening devices: … . . . . . . . . . . . . . . . . .
3.2.3.1.3. Drawing clearly showing the position of the tank(s) in the

vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3.2. Reserve fuel tank(s)
3.2.3.2.1. Number and capacity of each tank: … . . . . . . . . . . . . . . . . . . . . . .
3.2.3.2.1.1. Material: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3.2.2. Drawing and technical description of the tank(s) with all

connections and all lines of the breathing and venting
system, locks, valves, fastening devices: … . . . . . . . . . . . . . . . . .
3.2.3.2.3. Drawing clearly showing the position of the tank(s) in the

vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4. Fuel feed

3.2.4.1. By carburettor(s): yes/no (1)
▼M21
3.2.4.2. By fuel injection (compression ignition or dual-fuel only):
yes/no (1)
▼M27
3.2.4.2.1. System description (common rail/unit injectors/distribution
pump etc.): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.4.2.2. Working principle: direct injection/pre-chamber/swirl
chamber (1)
▼M27
3.2.4.2.3. Injection/Delivery pump
▼M1
3.2.4.2.3.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.3.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.3.3. Maximum fuel delivery (1) (2): …… mm3 /stroke or cycle at an

engine speed of: … . . min-1 or, alternatively, a characteristic
diagram: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(When boost control is supplied, state the characteristic fuel

delivery and boost pressure versus engine speed)
3.2.4.2.3.4. Static injection timing (2): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.3.5. Injection advance curve (2): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.3.6. Calibration procedure: test bench/engine (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 51
▼M27
3.2.4.2.4. Engine speed limitation control
▼M1
3.2.4.2.4.1. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.4.2. Cut-off point
3.2.4.2.4.2.1. Speed at which cut-off starts under load: …… . . . . . . . . min-1
3.2.4.2.4.2.2. Maximum no-load speed: ……. . . . . . . . . . . . . . . . . . . . . . . . min-1
3.2.4.2.4.2.3. Idling speed: ….. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . min-1
3.2.4.2.5. Injection piping (heavy-duty vehicles only)
3.2.4.2.5.1. Length: …… mm
3.2.4.2.5.2. Internal diameter: …… mm
3.2.4.2.5.3. Common rail, make and type: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.6. Injector(s)
3.2.4.2.6.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.6.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.6.3. Opening pressure (2): … kPa or characteristic diagram (2): …
3.2.4.2.7. Cold start system
3.2.4.2.7.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.7.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.7.3. Description: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.8. Auxiliary starting aid
3.2.4.2.8.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.8.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.8.3. System description: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.9. Electronic controlled injection: yes/no (1)
3.2.4.2.9.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.9.2. Type(s):
▼M27
3.2.4.2.9.3. Description of the system
▼M1
3.2.4.2.9.3.1. Make and type of the control unit (ECU): … . . . . . . . . . . . . . . .
▼M27
3.2.4.2.9.3.1.1. Software version of the ECU: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.4.2.9.3.2. Make and type of the fuel regulator: … . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.9.3.3. Make and type of the air-flow sensor: … . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 52
▼M1
3.2.4.2.9.3.4. Make and type of fuel distributor: … . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.9.3.5. Make and type of the throttle housing: …. . . . . . . . . . . . . . . . . . .
▼M27
3.2.4.2.9.3.6. Make and type or working principle of water temperature
sensor: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.2.9.3.7. Make and type or working principle of air temperature sensor:

… ..........................................................
3.2.4.2.9.3.8. Make and type or working principle of air pressure sensor: …
▼M1
3.2.4.2.9.3.9. Software calibration number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3. By fuel injection (positive ignition only): yes/no (1)
3.2.4.3.1. Working principle: intake manifold (single-/multi-point/direct

injection (1) /other (specify): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.2. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.3. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.4. System description (In the case of systems other than

continuous injection give equivalent details): … . . . . . . . . . . . . .
3.2.4.3.4.1. Make and type of the control unit (ECU): … . . . . . . . . . . . . . . .
▼M27
3.2.4.3.4.1.1. Software version of the ECU: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.4.3.4.2. Make and type of fuel regulator: …. . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.2.4.3.4.3. Make and type or working principle of air-flow sensor: … . .
▼M1
3.2.4.3.4.4. Make and type of fuel distributor: … . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.4.5. Make and type of pressure regulator: … . . . . . . . . . . . . . . . . . . . .
3.2.4.3.4.6. Make and type of micro switch: … . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.4.7. Make and type of idling adjustment screw: … . . . . . . . . . . . . . .
3.2.4.3.4.8. Make and type of throttle housing: … . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.2.4.3.4.9. Make and type or working principle of water temperature
sensor: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.4.10. Make and type or working principle of air temperature sensor:

… ..........................................................
02007L0046 — EN — 18.01.2018 — 021.001 — 53
▼M27
3.2.4.3.4.11. Make and type or working principle of air pressure sensor: …
▼M1
3.2.4.3.4.12. Software calibration number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.2.4.3.5. Injectors
▼M1
3.2.4.3.5.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.5.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.6. Injection timing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.7. Cold start system
3.2.4.3.7.1. Operating principle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.3.7.2. Operating limits/settings (1) (2): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.4. Feed pump
3.2.4.4.1. Pressure (2): …. . . . kPa or characteristic diagram (2): … . . . .
▼M27
3.2.4.4.2. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4.4.3. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.5. Electrical system
3.2.5.1. Rated voltage: …… . . . . . . . . . . V, positive/negative ground (1)
3.2.5.2. Generator
3.2.5.2.1. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5.2.2. Nominal output: …… VA
3.2.6. Ignition system (spark ignition engines only)

3.2.6.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.3. Working principle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.4. Ignition advance curve or map (2): … . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.5. Static ignition timing (2): …… . . . . . . . . . degrees before TDC
3.2.6.6. Spark plugs
3.2.6.6.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.6.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.6.3. Gap setting: ……mm
3.2.6.7. Ignition coil(s)
3.2.6.7.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6.7.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7. Cooling system: liquid/air (1)

3.2.7.1. Nominal setting of the engine temperature control mechanism:
… ..........................................................
02007L0046 — EN — 18.01.2018 — 021.001 — 54
▼M1
3.2.7.2. Liquid
3.2.7.2.1. Nature of liquid: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.2.2. Circulating pump(s): yes/no (1)
3.2.7.2.3. Characteristics: ………. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or
3.2.7.2.3.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.2.3.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.2.4. Drive ratio(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.2.5. Description of the fan and its drive mechanism: … . . . . . . . . .
3.2.7.3. Air
3.2.7.3.1. Fan: yes/no (1)
3.2.7.3.2. Characteristics: ……. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or
3.2.7.3.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.3.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7.3.3. Drive ratio(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8. Intake system

3.2.8.1. Pressure charger: yes/no (1)
3.2.8.1.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8.1.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8.1.3. Description of the system (e.g. maximum charge pressure:

…… . . . . . . . . . . . kPa; wastegate if applicable): … . . . . . . . . . . .
3.2.8.2. Intercooler: yes/no (1)
3.2.8.2.1. Type: air-air/air-water (1)
3.2.8.3. Intake depression at rated engine speed and at 100 % load

(compression ignition engines only)
3.2.8.3.1. Minimum allowable: ………. . . . . . . . . . . . . . . . . . . . . . . . . . . kPa
3.2.8.3.2. Maximum allowable: ……… . . . . . . . . . . . . . . . . . . . . . . . . . . . kPa
▼M11
3.2.8.3.3. (Euro VI only) Actual Intake system depression at rated engine
speed and at 100 % load on the vehicle: kPa
▼M1
3.2.8.4. Description and drawings of inlet pipes and their accessories
(plenum chamber, heating device, additional air intakes, etc.):
… ..........................................................
3.2.8.4.1. Intake manifold description (include drawings and/or photos):

… ..........................................................
3.2.8.4.2. Air filter, drawings: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or
3.2.8.4.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8.4.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8.4.3. Intake silencer, drawings: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or
3.2.8.4.3.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8.4.3.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 55
▼M1
3.2.9. Exhaust system
3.2.9.1. Description and/or drawing of the exhaust manifold: … . . . . .
3.2.9.2. Description and/or drawing of the exhaust system: … . . . . . . .
▼M21
3.2.9.2.1. (Euro VI only) Description and/or drawing of the elements of
the exhaust system that are part of the engine system
▼M1
3.2.9.3. Maximum allowable exhaust back pressure at rated engine
speed and at 100 % load (compression ignition engines
only): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kPa
▼M11
3.2.9.3.1. (Euro VI only) Actual exhaust back pressure at rated engine
speed and at 100 % load on the vehicle (compression-ignition
engines only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kPa
▼M1
3.2.9.4. Type, marking of exhaust silencer(s): … . . . . . . . . . . . . . . . . . . . .
Where relevant for exterior noise, reducing measures in the

engine compartment and on the engine: … . . . . . . . . . . . . . . . . . .
3.2.9.5. Location of the exhaust outlet: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.9.6. Exhaust silencer containing fibrous materials: … . . . . . . . . . . . .
▼M21
3.2.9.7. Complete exhaust system volume: … . . . . . . . . . . . . . . . . . . dm3
3.2.9.7.1. (Euro VI only) Acceptable exhaust system volume: … . dm3
3.2.9.7.2. (EURO VI only) Volume of the exhaust system that is part of

the engine system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dm3
▼M1
3.2.10. Minimum cross-sectional areas of inlet and outlet ports: … .
3.2.11. Valve timing or equivalent data

3.2.11.1. Maximum lift of valves, angles of opening and closing, or
timing details of alternative distribution systems, in relation
to dead centres. For variable timing system, minimum and
maximum timing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.11.2. Reference and/or setting ranges (1): …. . . . . . . . . . . . . . . . . . . . . . .
3.2.12. Measures taken against air pollution

3.2.12.1. Device for recycling crankcase gases (description and
drawings): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M11
3.2.12.1.1. (Euro VI only) Device for recycling crankcase gases:
yes/no (2)
If yes, description and drawings:
If no, compliance with Annex V to Regulation (EU)

No 582/2011 required
▼M27
3.2.12.2. Pollution control devices (if not covered by another heading)
3.2.12.2.1. Catalytic converter

02007L0046 — EN — 18.01.2018 — 021.001 — 56
▼M1
3.2.12.2.1.1. Number of catalytic converters and elements (provide the
information below for each separate unit): … . . . . . . . . . . . . . . .
3.2.12.2.1.2. Dimensions, shape and volume of the catalytic converter(s): …
▼M29
3.2.12.2.1.3. Type of catalytic action: … (oxidising, three-way, lean NOx
trap, SCR, lean NOx catalyst or other)
▼M1
3.2.12.2.1.4. Total charge of precious metals: … . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.5. Relative concentration: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.6. Substrate (structure and material): … . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.7. Cell density: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.8. Type of casing for the catalytic converter(s): … . . . . . . . . . . . . .
3.2.12.2.1.9. Location of the catalytic converter(s) (place and reference

distance in the exhaust line): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.10. Heat shield: yes/no (1)
▼M27
3.2.12.2.1.11. Normal operating temperature range: … . . . . . . . . . . . . . . . . . °C
▼M1
3.2.12.2.1.12. Make of catalytic converter: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.1.13. Identifying part number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.2.12.2.2. Sensors
3.2.12.2.2.1. Oxygen sensor: yes/no (1)
3.2.12.2.2.1.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.1.2. Location: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.1.3. Control range: ….
3.2.12.2.2.1.4. Type or working principle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.1.5. Identifying part number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.2. NOx sensor: yes/no (1)
3.2.12.2.2.2.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.2.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.2.3. Location: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.3. Particulate sensor: yes/no (1)
3.2.12.2.2.3.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 57
▼M27
3.2.12.2.2.3.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.2.3.3. Location: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.12.2.3. Air injection: yes/no (1)
3.2.12.2.3.1. Type (pulse air, air pump, etc.): … . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.4. Exhaust gas recirculation (EGR): yes/no (1)
▼M27
3.2.12.2.4.1. Characteristics (make, type, flow, high pressure / low pressure /
combined pressure, etc.): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.4.2. Water-cooled system (to be specified for each EGR system

e.g. low pressure / high pressure / combined pressure:
yes/no (1)
3.2.12.2.5. Evaporative emissions control system (petrol and ethanol

engines only): yes/no (1)
3.2.12.2.5.1. Detailed description of the devices: ….. . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.5.2. Drawing of the evaporative control system: … . . . . . . . . . . . . . .
3.2.12.2.5.3. Drawing of the carbon canister: … . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.5.4. Mass of dry charcoal: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . g
3.2.12.2.5.5. Schematic drawing of the fuel tank with indication of capacity

and material (petrol and ethanol engines only): …. . . . . . . . . . .
3.2.12.2.5.6. Description and schematic of the heat shield between tank and
exhaust system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.12.2.6. Particulate trap (PT): yes/no (1)
3.2.12.2.6.1. Dimensions, shape and capacity of the particulate trap: …. . .
3.2.12.2.6.2. Design of the particulate trap: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.3. Location (reference distance in the exhaust line): … . . . . . . . . .
▼M27
__________
3.2.12.2.6.4. Make of particulate trap: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.6.5. Identifying part number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
3.2.12.2.6.7. Normal operating temperature: … . . . . . . . . . (K) and pressure
range … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (KPa)

02007L0046 — EN — 18.01.2018 — 021.001 — 58
▼M1
3.2.12.2.6.8. In the case of periodic regeneration (heavy-duty vehicles only)
3.2.12.2.6.8.1. Number of ETC test cycles between 2 regenerations (n1):

… . . . . . . . . . . . . . . . . . . ►M11 (not applicable to Euro VI) ◄
▼M11
3.2.12.2.6.8.1.1. (Euro VI only) Number of WHTC test cycles without regen
eration (n):
▼M1
3.2.12.2.6.8.2. Number of ETC cycles during regeneration (n2): …. . . . . . . . .
►M11 (not applicable to Euro VI) ◄
▼M11
3.2.12.2.6.8.2.1. (Euro VI only) Number of WHTC test cycles with regen
eration (nR):
3.2.12.2.6.9. Other systems: yes/no (1)
3.2.12.2.6.9.1. Description and operation
▼M27
3.2.12.2.7. On-board-diagnostic (OBD) system: yes/no (1): … . . . . . . . . . . .
3.2.12.2.7.0.1. (Euro VI only) Number of OBD engine families within the

engine family
3.2.12.2.7.0.2. (Euro VI only) List of the OBD engine families (when

applicable)
3.2.12.2.7.0.3. (Euro VI only) Number of the OBD engine family the parent
engine / the engine member belongs to: … . . . . . . . . . . . . . . . . .
3.2.12.2.7.0.4. (Euro VI only) Manufacturer references of the

OBD-Documentation required by Article 5(4)(c) and
Article 9(4) of Regulation (EU) No 582/2011 and specified
in Annex X to that Regulation for the purpose of approving
the OBD system
3.2.12.2.7.0.5. (Euro VI only) When appropriate, manufacturer reference of

the Documentation for installing in a vehicle an OBD
equipped engine system
3.2.12.2.7.0.6. (Euro VI only) When appropriate, manufacturer reference of

the documentation package related to the installation on the
vehicle of the OBD system of an approved engine
▼M21
__________
▼M1
3.2.12.2.7.1. Written description and/or drawing of the MI: … . . . . . . . . . . .
3.2.12.2.7.2. List and purpose of all components monitored by the OBD

system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3. Written description (general working principles) for
3.2.12.2.7.3.1 Positive-ignition engines
3.2.12.2.7.3.1.1. Catalyst monitoring: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.1.2. Misfire detection: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.1.3. Oxygen sensor monitoring: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 59
▼M1
3.2.12.2.7.3.1.4. Other components monitored by the OBD system: … . . . . . . .
3.2.12.2.7.3.2. Compression-ignition engines: …. . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.2.1. Catalyst monitoring: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.2.2. Particulate trap monitoring: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.2.3. Electronic fuelling system monitoring: … . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.2.4. deNOx system monitoring: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.3.2.5 Other components monitored by the OBD system: … . . . . . . .
3.2.12.2.7.4. Criteria for MI activation (fixed number of driving cycles or

statistical method): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.5. List of all OBD output codes and formats used (with expla
nation of each): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.7.6. The following additional information shall be provided by the

vehicle manufacturer for the purposes of enabling the manu
facture of OBD-compatible replacement or service parts and
diagnostic tools and test equipment.
3.2.12.2.7.6.1. A description of the type and number of the preconditioning

cycles used for the original type approval of the vehicle.
3.2.12.2.7.6.2. A description of the type of the OBD demonstration cycle

used for the original type-approval of the vehicle for the
component monitored by the OBD system.
►M29 3.2.12.2.7.6.3. ◄ A comprehensive document describing all sensed

components with the strategy for fault detection and MI acti
vation (fixed number of driving cycles or statistical method),
including a list of relevant secondary sensed parameters for
each component monitored by the OBD system. A list of all
OBD output codes and format used (with an explanation of
each) associated with individual emission related power-train
components and individual non-emission related components,
where monitoring of the component is used to determine MI
activation, including in particular a comprehensive explanation
for the data given in service $05 Test ID $21 to FF and the
data given in service $06.
In the case of vehicle types that use a communication link in

accordance with ISO 15765-4 ‘Road vehicles, diagnostics on
controller area network (CAN) — Part 4: requirements for
emissions-related systems’, a comprehensive explanation for
the data given in service $06 Test ID $00 to FF, for each
OBD monitor ID supported, shall be provided.
02007L0046 — EN — 18.01.2018 — 021.001 — 60
▼M1
3.2.12.2.7.6.4. The information required above may be defined by completing
a table as described below.
3.2.12.2.7.6.4.1. ►M27 L i g h t - d u t y v e h i c l e s ◄
Fault MI acti
Monitoring Secondary Precondi Demon
Component Fault cod detection vation
strategy parameters tioning stration test
criteria criteria
Catalyst P0420 Oxygen Difference 3rd cycle Engine Two type Type I
sensor 1 between speed I cycles
and sensor 1 load, A/F
sensor 2 and sensor mode,
signals 2 signals- catalyst
tempera-
ture
3.2.12.2.7.6.4.2. Heavy-duty vehicles
Fault MI acti
Monitoring Secondary precondi Demon
Component Fault code detection vation
strategy parameters tioning stration test
criteria criteria
SCR Pxxx NOx Difference 3rd cycle Engine Three OBD test
Catalyst sensor 1 between speed OBD test cycle
and sensor 1 load, cycles (3 (short ESC
sensor 2 and sensor catalyst short cycle)
signals 2 signals- tempera- ESC
ture, cycles)
reagent
activity
▼M21
3.2.12.2.7.6.5. (Euro VI only) OBD Communication protocol standard: (8)
▼M11
3.2.12.2.7.7. (Euro VI only) Manufacturer reference of the OBD related
information required by of Article 5(4)(d) and Article 9(4)
of Regulation (EU) No 582/2011 for the purpose of
complying with the provisions on access to vehicle OBD
and vehicle Repair and Maintenance Information, or
3.2.12.2.7.7.1. As an alternative to a manufacturer reference provided in

Section 3.2.12.2.7.7 reference of the attachment to the
information document set out in Appendix 4 of Annex I to
Regulation (EU) No 582/2011 that contains the following
table, once completed according to the given example:
02007L0046 — EN — 18.01.2018 — 021.001 — 61
▼M11
Component — Fault code — Monitoring strategy — Fault
detection criteria — MI activation criteria — Secondary
parameters — Preconditioning — Demonstration test
Catalyst – P0420 — Oxygen sensor 1 and 2 signals —

Difference between sensor 1 and sensor 2 signals — 3rd
cycle — Engine speed, engine load, A/F mode, catalyst
temperature — Two Type 1 cycles — Type 1
▼M21
3.2.12.2.7.8. (EURO VI only) OBD components on-board the vehicle
3.2.12.2.7.8.0. Alternative approval as provided for in point 2.4.1 of Annex X

to Regulation (EU) No 582/2011: yes/no (1)
3.2.12.2.7.8.1. List of OBD components on-board the vehicle
3.2.12.2.7.8.2. Written description and/or drawing of the MI (10)
3.2.12.2.7.8.3. Written description and/or drawing of the OBD off-board

communication interface (10)
▼M27
3.2.12.2.8. Other system: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M11
3.2.12.2.8.1. (Euro VI only) Systems to ensure the correct operation of NOx
control measures
▼M21
3.2.12.2.8.2. Driver inducement system
3.2.12.2.8.2.1. (Euro VI only) Engine with permanent deactivation of the

driver inducement, for use by the rescue services or in
vehicles specified in point (b) of Article 2(3) of this Directive:
yes/no (1)
3.2.12.2.8.2.2. Activation of the creep mode
‘disable after restart’/‘disable after fuelling’/‘disable after

parking’ (1) (8)
▼M27
3.2.12.2.8.2.3. Type of inducement system: no engine restart after
countdown/no start after refuelling/fuel-lockout/performance
restriction
3.2.12.2.8.2.4. Description of the inducement system
3.2.12.2.8.2.5. Equivalent to the average driving range of the vehicle with a

complete tank of fuel: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . km
▼M11
3.2.12.2.8.3. (Euro VI only) Number of OBD engine families within the
engine family considered when ensuring the correct operation
of NOx control measures
▼M21
3.2.12.2.8.3.1. (Euro VI only) List of the OBD engine families within the
of NOx control measures (when applicable)
engine/the engine member belongs to
02007L0046 — EN — 18.01.2018 — 021.001 — 62
▼M21
__________
▼M27
3.2.12.2.8.4. (Euro VI only) List of the OBD engine families (when
applicable): …
▼M11
3.2.12.2.8.5. (Euro VI only) Number of the OBD engine family the parent
engine / the engine member belongs to
3.2.12.2.8.6. (Euro VI only) Lowest concentration of the active ingredient

present in the reagent that does not activate the warning
system (CDmin): (% vol.)
3.2.12.2.8.7. (Euro VI only) When appropriate, manufacturer reference of

the Documentation for installing in a vehicle the systems to
ensure the correct operation of NOx control measures
▼M21
3.2.12.2.8.8. (EURO VI only) Components on-board the vehicle of the
systems ensuring the correct operation of NOx control
measures
3.2.12.2.8.8.1. List of components on-board the vehicle of the systems

ensuring the correct operation of NOx control measures
▼M11
3.2.12.2.8.8.2. When appropriate, manufacturer reference of the documen
tation package related to the installation on the vehicle of
the system ensuring the correct operation of NOx control
measures of an approved engine
▼M21
3.2.12.2.8.8.3. Written description and/or drawing of the warning signal (10)
3.2.12.2.8.8.4. Alternative approval provided for in point 2.1 of Annex XIII

to Regulation (EU) No 582/2011: yes/no (1)
3.2.12.2.8.8.5. Heated/non-heated reagent tank and dosing system (see

paragraph 2.4 of Annex 11 to UNECE Regulation No 49)
▼M1
3.2.12.2.9. Torque limiter: yes/no (1)
3.2.12.2.9.1. Description of the torque limiter activation (heavy-duty

vehicles only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12.2.9.2. Description of the full load curve limitation (heavy-duty

vehicles only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 63
▼M27
3.2.12.2.10. Periodically regenerating system: (provide the information
below for each separate unit)
3.2.12.2.10.1. Method or system of regeneration, description and/or drawing:

….
3.2.12.2.10.2. The number of Type 1 operating cycles, or equivalent engine

test bench cycles, between two cycles where regenerative
phases occur under the conditions equivalent to Type 1 test
(Distance ‘D’ in Figure A6.App1/1 in Appendix 1 to
Sub-Annex 6 of Annex XXI to Regulation (EU) 2017/1151
or figure A13/1 in Annex 13 to UN/ECE Regulation 83 (as
applicable)): …
3.2.12.2.10.2.1. Applicable Type 1 cycle (indicate the applicable procedure:

Annex XXI, Sub-Annex 4 or UN/ECE Regulation 83): …
3.2.12.2.10.3. Description of method employed to determine the number of

cycles between two cycles where regenerative phases occur:
… ..........................................................
3.2.12.2.10.4. Parameters to determine the level of loading required before

regeneration occurs (i.e. temperature, pressure etc.): … . . . . . .
3.2.12.2.10.5. Description of method used to load system in the test

procedure described in paragraph 3.1., Annex 13 to UN/ECE
Regulation 83: ….
3.2.12.2.11. Catalytic converter systems using consumable reagents

(provide the information below for each separate unit)
yes/no (1)
3.2.12.2.11.1. Type and concentration of reagent needed: …
3.2.12.2.11.2. Normal operational temperature range of reagent: …
3.2.12.2.11.3. International standard: …
3.2.12.2.11.4. Frequency of reagent refill: continuous/maintenance (where

appropriate):
3.2.12.2.11.5. Reagent indicator (description and location): …
3.2.12.2.11.6. Reagent tank
3.2.12.2.11.6.1. Capacity: …
3.2.12.2.11.6.2. Heating system: yes/no
3.2.12.2.11.6.2.1. Description or drawing: …
3.2.12.2.11.7. Reagent control unit: yes/no (1)
3.2.12.2.11.7.1. Make: …
3.2.12.2.11.7.2. Type: …
3.2.12.2.11.8. Reagent injector (make type and location): …

02007L0046 — EN — 18.01.2018 — 021.001 — 64
▼M1
3.2.13. Smoke opacity
3.2.13.1. Location of the absorption coefficient symbol (compression
ignition engines only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.13.2. Power at six points of measurement (see point 2.1 of

Annex III to Directive 72/306/EEC as amended)
3.2.13.3. Engine power measured on test bench/on the vehicle (1)
3.2.13.3.1. Declared speeds and powers
Measurement points Engine speed (min-1) Power (kW)
1……
2……
3……
4……
5……
6……
3.2.14. Details of any devices designed to influence fuel economy (if

not covered by other items): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15. LPG fuelling system: yes/no (1)

▼M27
3.2.15.1. Type-approval number according to Regulation (EC)
No 661/2009 (OJ L 200, 31.7.2009, p. 1): … . . . . . . . . . . . . . . .
▼M1
3.2.15.2. Electronic engine management control unit for LPG fuelling
3.2.15.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15.2.3. Emission-related adjustment possibilities: … . . . . . . . . . . . . . . . . .
3.2.15.3. Further documentation
3.2.15.3.1. Description of the safeguarding of the catalyst at switch-over

from petrol to LPG or back: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15.3.2. System lay-out (electrical connections, vacuum connections

compensation hoses, etc.): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15.3.3. Drawing of the symbol: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.16. NG fuelling system: yes/no (1)

▼M27
3.2.16.1. Type-approval number according to Regulation (EC)
No 661/2009 (OJ L 200, 31.7.2009, p. 1): … . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 65
▼M1
3.2.16.2. Electronic engine management control unit for NG fuelling
3.2.16.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.16.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

from petrol to NG or back: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

▼M21
3.2.17. Specific information related to gas and dual-fuel engines for
heavy-duty vehicles (in the case of systems laid out in a
different manner, supply equivalent information)(if applicable)
▼M1
3.2.17.1. Fuel: LPG/NG-H/NG-L/NG-HL (1)
3.2.17.2. Pressure regulator(s) or vaporiser/pressure regulator(s) (1)
3.2.17.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.2.3. Number of pressure reduction stages: … . . . . . . . . . . . . . . . . . . . .
3.2.17.2.4. Pressure in final stage
minimum: ….. . . . . . . . . . kPa — maximum: …. . . . . . . . . kPa
3.2.17.2.5. Number of main adjustment points: … . . . . . . . . . . . . . . . . . . . . . .
3.2.17.2.6. Number of idle adjustment points: … . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.2.7. Type-approval number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.3. Fuelling system: mixing unit/gas injection/liquid injection/

direct injection (1)
3.2.17.3.1. Mixture strength regulation: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.3.2. System description and/or diagram and drawings: … . . . . . . . .
3.2.17.4. Mixing unit
3.2.17.4.1. Number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.4.2. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.4.3. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.4.4. Location: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.4.5. Adjustment possibilities: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5. Inlet manifold injection
3.2.17.5.1. Injection: single point/multipoint (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 66
▼M1
3.2.17.5.2. Injection: continuous/simultaneously timed/sequentially
timed (1)
3.2.17.5.3. Injection equipment
3.2.17.5.3.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.3.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.3.3. Adjustment possibilities: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.3.4. Type-approval number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.4. Supply pump (if applicable)
3.2.17.5.4.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.4.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.5. Injector(s) … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.5.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.5.5.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6. Direct injection
3.2.17.6.1. Injection pump/pressure regulator (1)
3.2.17.6.1.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.1.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.1.3. Injection timing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.2. Injector(s) … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.6.2.3. Opening pressure or characteristic diagram (2): … . . . . . . . . . . .
3.2.17.7. Electronic control unit (ECU)
3.2.17.7.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.7.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.7.3. Adjustment possibilities: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.7.4. Software calibration number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.8. NG fuel-specific equipment
3.2.17.8.1. Variant 1 (only in the case of approvals of engines for several

specific fuel compositions)
02007L0046 — EN — 18.01.2018 — 021.001 — 67
▼M11
3.2.17.8.1.0.1. (Euro VI only) Self adaptive feature? Yes/No (1)
3.2.17.8.1.0.2. (Euro VI only) Calibration for a specific gas composition

NG-H/NG-L/NG-HL (1)
Transformation for a specific gas composition NG-Ht/NG-

Lt/NG-HLt (1)
▼M1
3.2.17.8.1.1. Fuel composition:
methane (CH4): basis: ……. % mole min. …. % mole max. ….. % mole
ethane (C2H6): basis: ……. % mole min. …. % mole max. ….. % mole
propane (C3H8): basis: ……. % mole min. …. % mole max. ….. % mole
butane (C4H10): basis: ……. % mole min. …. % mole max. ….. % mole
C5/C5+: basis: ……. % mole min. …. % mole max. ….. % mole
oxygen (O2): basis: ……. % mole min. …. % mole max. ….. % mole
inert (N2, He, etc.): basis: ……. % mole min. …. % mole max. ….. % mole
3.2.17.8.1.2. Injector(s)
3.2.17.8.1.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.8.1.2.2 Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.8.1.3. Others (if applicable): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.17.8.2. Variant 2 (only in the case of approvals for several specific

fuel compositions)
▼M21
3.2.17.9. When appropriate, manufacturer reference of the documen
tation for installing the dual-fuel engine in a vehicle (x1)
3.2.18. Hydrogen fuelling system: yes/no (1)
3.2.18.1. EC type-approval number in accordance with Regulation (EC)

No 79/2009: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.18.2. Electronic engine management control unit for hydrogen

fuelling
3.2.18.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.18.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

from petrol to hydrogen or back: … . . . . . . . . . . . . . . . . . . . . . . . .

3.2.19. H2NG fuelling system: yes/no (1)
3.2.19.1. Percentage of hydrogen in the fuel (the maximum specified by

the manufacturer): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 68
▼M21
3.2.19.2. EC type-approval number in accordance with UNECE Regu
lation No 110 … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.19.3. Electronic engine management control unit for H2NG fuelling
3.2.19.3.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.19.3.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

from petrol to H2NG or back: … . . . . . . . . . . . . . . . . . . . . . . . . . . .

▼M27
3.2.20. Heat storage information
3.2.20.1. Active heat storage device: yes/no
3.2.20.1.1. Enthalpy: … (J)
3.2.20.2. Insulation materials
3.2.20.2.1. Insulation material: …
3.2.20.2.2. Insulation volume: …
3.2.20.2.3. Insulation weight: …
3.2.20.2.4. Insulation location: …
3.3. Electric machine

▼M1
3.3.1. Type (winding, excitation): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1.1. Maximum hourly output: …… kW
▼M20
3.3.1.1.1. Maximum net power (n) …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . kW
(manufacturer’s declared value)
3.3.1.1.2. Maximum 30 minutes power (n) …. . . . . . . . . . . . . . . . . . . . . kW
▼M1
3.3.1.2. Operating voltage: …… V
▼M27
3.3.2. REESS
▼M1
3.3.2.1. Number of cells: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2.2. Mass: …… kg
3.3.2.3. Capacity: …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ah (Amp-hours)
3.3.2.4. Position: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.4. Combinations of propulsion energy converters
▼M1
3.4.1. Hybrid electric vehicle: yes/no (1)
3.4.2. Category of hybrid electric vehicle: off-vehicle charging/not

off-vehicle charging: (1)
3.4.3. Operating mode switch: with/without (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 69
▼M1
3.4.3.1. Selectable modes
3.4.3.1.1. Pure electric: yes/no (1)
3.4.3.1.2. Pure fuel consuming: yes/no (1)
3.4.3.1.3. Hybrid modes: yes/no (1)
(if yes, short description): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.4.4. Description of the energy storage device: (REESS, capacitor,
flywheel/generator)
▼M1
3.4.4.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.4.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.4.3. Identification number: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.4.4. Kind of electrochemical couple: …. . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.4.4.5. Energy: … . . . . (for REESS: voltage and capacity Ah in 2 h,
for capacitor: J, …)
▼M1
3.4.4.6. Charger: on board/external/without (1)
▼M27
3.4.5. Electric machine (describe each type of electric machine
separately)
▼M1
3.4.5.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.5.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.5.3. Primary use: traction motor/generator (1)
3.4.5.3.1. When used as traction motor: single-/multimotors (number) (1):

… ..........................................................
3.4.5.4. Maximum power: …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kW
3.4.5.5. Working principle
3.4.5.5.5.1 Direct current/alternating current/number of phases: … . . . . . .
3.4.5.5.2. Separate excitation/series/compound (1)
3.4.5.5.3. Synchronous/asynchronous (1)
3.4.6. Control unit

3.4.6.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.6.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.7. Power controller

3.4.7.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4.7.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M21
3.4.8. Vehicle electric range … km (in accordance with Annex 9 to
UNECE Regulation No 101)
▼M1
3.4.9. Manufacturer's recommendation for preconditioning: … . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 70
▼M27
3.5. Manufacturer's declared values for determination of CO2
emissions/fuel consumption/electric consumption/electric
range and details of eco-innovations (where applicable) (o)
▼M1
3.5.1. CO2 mass emissions
3.5.1.1. CO2 mass emissions (urban conditions): …… . . . . . . . . . g/km
3.5.1.2. CO2 mass emissions (extra-urban conditions): ……. . . . g/km
3.5.1.3. CO2 mass emissions (combined): …… . . . . . . . . . . . . . . . . g/km
3.5.2. Fuel consumption (provide details for each reference fuel

tested)
▼M21
3.5.2.1. Fuel consumption (urban conditions) … . . . . . . . . . . . l/100 km
or m3/100 km or kg/100 km (1)
3.5.2.2. Fuel consumption (extra-urban conditions) … . . . . . l/100 km

or m3/100 km or kg/100 km (1)
3.5.2.3. Fuel consumption (combined) … . . . l/100 km or m3/100 km

or kg/100 km (1)
▼M18
__________
▼M21
3.5.3. Electric energy consumption for electric vehicles
3.5.3.1. Electric energy consumption for pure electric vehicles …. . . .
Wh/km
3.5.3.2. Electric energy consumption for externally chargeable hybrid

electric vehicles
3.5.3.2.1. Electric energy consumption (Condition A, combined) … . . .

Wh/km
3.5.3.2.2. Electric energy consumption (Condition B, combined) …. . . .

Wh/km
3.5.3.2.3. Electric energy consumption (weighted combined) … Wh/km
▼M11
3.5.4. CO2 emissions for heavy duty engines (Euro VI only)
▼M21
3.5.4.1. CO2 mass emissions WHSC test (x3): … . . . . . . . . . . . . g/kWh
3.5.4.2. CO2 mass emissions WHSC test in diesel mode (x2): … g/kWh
3.5.4.3. CO2 mass emissions WHSC test in dual-fuel mode (x1): … . .

g/kWh
3.5.4.4. CO2 mass emissions WHTC test (x3) (9): … . . . . . . . . . g/kWh
3.5.4.5. CO2 mass emissions WHTC test in diesel mode (x2) (9): … . .
g/kWh
3.5.4.6. CO2 mass emissions WHTC test in dual-fuel mode (x1) (9): …
g/kWh
▼M11
3.5.5. Fuel consumption for heavy duty engines (Euro VI only)
▼M21
3.5.5.1. Fuel consumption WHSC test (x3): … . . . . . . . . . . . . . . . g/kWh
02007L0046 — EN — 18.01.2018 — 021.001 — 71
▼M21
3.5.5.2. Fuel consumption WHSC test in diesel mode (x2): … g/kWh
3.5.5.3. Fuel consumption WHSC test in in dual-fuel mode (x1): … . .

g/kWh
3.5.5.4. Fuel consumption WHTC test (9) (x3): … . . . . . . . . . . . . g/kWh
3.5.5.5. Fuel consumption WHTC test in diesel mode (9) (x2): …. . . . .

g/kWh
3.5.5.6. Fuel consumption WHTC test in dual-fuel mode (9) (x1): …. .

g/kWh
▼M25
3.5.6. Vehicle fitted with an eco-innovation within the meaning of
Article 12 of Regulation (EC) No 443/2009 for M1 vehicles or
Article 12 of Regulation (EU) No 510/2011 for N1 vehicles:
yes/no (1)
3.5.6.1. Type/Variant/Version of the baseline vehicle as referred to in

Article 5 of Regulation (EU) No 725/2011 for M1 vehicles or
Article 5 of Regulation (EU) No 427/2014 for N1 vehicles (if
applicable) …
▼M18
3.5.6.2. Existence of interactions between different eco-innovations:
yes/no (1)
3.5.6.3. Emissions data related to the use of eco-innovations (repeat the

table for each reference fuel tested) (w1)
4. CO2
5. Usage CO2 emissions
3. CO2 emissions of
2. CO2 factor (UF), i.e. savings
Decision 1. CO2 emissions of the
Code of the emissions of temporal share of
approving the emissions of the baseline eco-innovation ðð1 Ä 2Þ
eco-inno the technology usage
eco-inno the baseline vehicle under vehicle under
vation (w3) eco-innovation in normal Äð3 Ä 4ÞÞ ä 5
vation (w2) vehicle Type 1 Type 1
vehicle (g/km) operation
(g/km) test-cycle (w4) test-cycle
conditions
(= 3.5.1.3)
xxxx/201x
Total CO2 emissions savings (g/km) (w5)
▼M30
3.5.7. CO2 emissions and fuel consumption certification (for
heavy-duty vehicles, as specified in Article 6 of Commission
Regulation (EU) 2017/2400)
3.5.7.1. Simulation tool license number:
▼M27
3.5.7.1.1 Vehicle high
3.5.7.1.1.1. Cycle Energy Demand: … J
3.5.7.1.1.2. Road load coefficients
3.5.7.1.1.2.1. f0: …. . . . . . . N
3.5.7.1.1.2.2. f1: . . . . . . . . . N/(km/h)
3.5.7.1.1.2.3. f2: . . . . . . . . . N/(km/h)2
3.5.7.1.2. Vehicle Low (if applicable)

02007L0046 — EN — 18.01.2018 — 021.001 — 72
▼M27
3.5.7.1.2.2.1. f0: …. . . . . . . N
3.5.7.1.2.2.2. f1: . . . . . . . . . N/(km/h)
3.5.7.1.2.2.3. f2: . . . . . . . . . N/(km/h)2
3.5.7.1.3. Vehicle M (if applicable)
3.5.7.1.3.2.1. f0: …. . . . . . . N
3.5.7.1.3.2.2. f1: …. . . . . . . N/(km/h)
3.5.7.1.3.2.3. f2: . . . . . . . . . N/(km/h)2
3.5.7.2. Combined CO2 mass emissions
3.5.7.2.1. CO2 mass emission for ICE
3.5.7.2.1.1. Vehicle High: . . . . . . g/km
▼M29
3.5.7.2.1.1.0. Vehicle High (NEDC): . . . . . . . . g/km
▼M27
3.5.7.2.1.2. Vehicle low (if applicable): . . . . . . . . g/km
▼M29
3.5.7.2.1.2.0. Vehicle low (if applicable) (NEDC): . . . . . . . g/km
▼M27
3.5.7.2.2. Charge Sustaining CO2 mass emission for OVC-HEVs and
NOVC-HEVs
3.5.7.2.2.1. Vehicle high: . . . . . . . . g/km
▼M29
3.5.7.2.2.1.0. Vehicle high (NEDC): . . . . . . . g/km
▼M27
3.5.7.2.2.2. Vehicle low (if applicable): . . . . . . . . g/km
▼M29
3.5.7.2.2.2.0. Vehicle low (if applicable) (NEDC): . . . . . . . g/km
▼M27
3.5.7.2.2.3. Vehicle M (if applicable): . . . . . . . . . g/km
▼M29
3.5.7.2.2.3.0. Vehicle M (if applicable) (NEDC): . . . . . . . . g/km
▼M27
3.5.7.2.3. Charge Depleting CO2 mass emission for OVC-HEVs
3.5.7.2.3.1. Vehicle high: … . . . . . . . . . . g/km
▼M29
3.5.7.2.3.1.0. Vehicle high (NEDC): … . . . . . . . . . . g/km
▼M27
3.5.7.2.3.2. Vehicle low (if applicable): … . . . . . . . . . . g/km
02007L0046 — EN — 18.01.2018 — 021.001 — 73
▼M29
3.5.7.2.3.2.0. Vehicle low (if applicable) (NEDC): … . . . . . . . . . . g/km
▼M27
3.5.7.2.3.3. Vehicle M (if applicable): … . . . . . . . . . g/km
▼M29
3.5.7.2.3.3.0. Vehicle M (if applicable) (NEDC): … . . . . . . . . . g/km
▼M27
3.5.7.3. Electric range for electrified vehicles
3.5.7.3.1. Pure Electric Range (PER) for PEVs
3.5.7.3.1.1. Vehicle high: … . . . . . . . . . . km
3.5.7.3.1.2. Vehicle low (if applicable): … . . . . . . . . . . km
3.5.7.3.2. All Electric Range AER for OVC-HEVs
3.5.7.3.2.1. Vehicle high: … . . . . . . . . . . km
3.5.7.3.2.2. Vehicle low (if applicable): … . . . . . . . . . . km
3.5.7.3.2.3. Vehicle M (if applicable): … . . . . . . . . . km
3.5.7.4. Charge Sustaining fuel consumption (FCCS) for FCHVs
3.5.7.4.1. Vehicle high: … . . . . . . . . . . kg/100 km
3.5.7.4.2. Vehicle low (if applicable): … . . . . . . . . . . . . . . . . . . kg/100 km
3.5.7.4.3. Vehicle M (if applicable): … . . . . . . . . . . . . . . . . . . . kg/100 km
3.5.7.5. Electric energy consumption for electrified vehicles
3.5.7.5.1. Combined electric energy consumption (ECWLTC) for Pure

electric vehicles
3.5.7.5.1.1. Vehicle high: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wh/km
3.5.7.5.1.2. Vehicle low (if applicable): … . . . . . . . . . . . . . . . . . . . . . . Wh/km
3.5.7.5.2. Utility factor weighted charge-depleting electric consumption

ECAC,CD (combined)
3.5.7.5.2.1. Vehicle high: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wh/km
3.5.7.5.2.2. Vehicle low (if applicable): … . . . . . . . . . . . . . . . . . . . . . . Wh/km
3.5.7.5.2.3. Vehicle M (if applicable): … . . . . . . . . . . . . . . . . . . . . . . . Wh/km
3.5.8. Vehicle fitted with an eco-innovation within the meaning of

Article 12 of Regulation (EC) No 443/2009 for M1 vehicles or
Article 12 of Regulation (EU) No 510/2011 for N1 vehicles:
yes/no (1)
3.5.8.1. Type/Variant/Version of the baseline vehicle as referred to in

Article 5 of Regulation (EU) No 725/2011 for M1 vehicles or
Article 5 of Regulation (EU) No 427/2014 for N1 vehicles (if
applicable): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 74
▼M27
3.5.8.2. Existence of interactions between different eco-innovations:
yes/no (1)
3.5.8.3. Emissions data related to the use of eco-innovations (repeat the

table for each reference fuel tested) (w1)
4. CO2 5. Usage
3. CO2
2. CO2 emissions of factor (UF), i.e.
Decision 1. CO2 emissions of CO2 emissions
Code of the emissions of the temporal share of
approving the emissions of the baseline savings
eco-innovation the eco-innovation technology usage
eco-innovation the baseline vehicle under ((1 – 2) –
w2 (w3) eco-innovation vehicle under in normal
( ) vehicle (g/km) type 1 (3 – 4))*5
vehicle (g/km) type 1 operation
test-cycle (w4)
test-cycle conditions
xxxx/201x
Total CO2 emissions saving (g/km) (w5)
▼M1
3.6. Temperatures permitted by the manufacturer
3.6.1. Cooling system
3.6.1.1. Liquid cooling
Maximum temperature at outlet: …… . . . . . . . . . . . . . . . . . . . . K
3.6.1.2. Air cooling

3.6.1.2.1. Reference point: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1.2.2. Maximum temperature at reference point: …… . . . . . . . . . . . K
3.6.2. Maximum outlet temperature of the inlet intercooler: …… K
3.6.3. Maximum exhaust temperature at the point in the exhaust

pipe(s) adjacent to the outer flange(s) of the exhaust
manifold or turbocharger: …… . . . . . . . . . . . . . . . . . . . . . . . . . . K
3.6.4. Fuel temperature

Minimum: ……. . . . . . . . . K — maximum: …… . . . . . . . . . K
For diesel engines at injection pump inlet, for gas fuelled

engines at pressure regulator final stage
3.6.5. Lubricant temperature

Minimum: …. . . . . . . . . . K — maximum: …… . . . . . . . . . . K
3.6.6. Fuel pressure

Minimum: ……. . . . . . . kPa — maximum: …… . . . . . . . kPa
At pressure regulator final stage, NG fuelled gas engines only.

02007L0046 — EN — 18.01.2018 — 021.001 — 75
▼M1
3.7. Engine-driven equipment
Power absorbed by the auxiliaries needed for operating the
engine as specified in and under the operation conditions of
Directive 80/1269/EEC, Annex I, Section 5.1.1.
Power absorbed (kW) at various engine speeds

Equipment
High Speed Speed Speed Ref.
Idle Low speed
speed A (*) B (*) C (*) speed (**)
P(a)
Auxiliaries needed for

operating the engine
(to be subtracted from
measured engine
power) see Appendix
1, Section 6.1.
(*) ESC test.

(**) ETC test only.
3.8. Lubrication system

3.8.1. Description of the system
3.8.1.1. Position of lubricant reservoir: … . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.1.2. Feed system (by pump/injection into intake/mixing with fuel,

etc.) (1)
3.8.2. Lubricating pump

3.8.2.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.2.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.3. Mixture with fuel

3.8.3.1. Percentage: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.4. Oil cooler: yes/no (1)

3.8.4.1. Drawing(s): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . or
3.8.4.1.1. Make(s): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.8.4.1.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. TRANSMISSION (p)
4.1. Drawing of the transmission: …. . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2. Type (mechanical, hydraulic, electric, etc.): … . . . . . . . . . . . .
4.2.1. A brief description of the electrical/electronic components (if

any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3. Moment of inertia of engine flywheel: … . . . . . . . . . . . . . . . . .
4.3.1. Additional moment of inertia with no gear engaged: … . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 76
▼M27
4.4. Clutch(es): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
4.4.1. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4.2. Maximum torque conversion: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5. Gearbox
4.5.1. Type (manual/automatic/CVT (continuously variable trans
mission)) (1)
▼M27
4.5.1.1. Predominant mode: yes/no (1)
4.5.1.2. Best mode (if no predominant mode): …. . . . . . . . . . . . . . . . . . . .
4.5.1.3. Worst mode (if no predominant mode): … . . . . . . . . . . . . . . . . . .
4.5.1.4. Torque rating: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.1.5. Number of clutches: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
4.5.2. Location relative to the engine: … . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5.3. Method of control: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
4.6. Gear ratios
Internal gearbox ratios Final drive ratio(s) (ratio of

Gear (ratios of engine to gearbox gearbox output shaft to Total gear ratios
output shaft revolutions) driven wheel revolutions)
Maximum for CVT
Minimum for CVT

Reverse
▼M1
4.7. Maximum vehicle design speed (in km/h) (q): … . . . . . . . . . .
4.8. Speedometer
4.8.1. Method of operation and description of drive mechanism: …
4.8.2. Instrument constant: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.8.3. Tolerance of the measuring mechanism (pursuant to item 2.1.3

of Annex II to Directive 75/443/EEC): …. . . . . . . . . . . . . . . . . . .
4.8.4. Overall transmission ratio (pursuant to item 2.1.2 of Annex II

to Directive 75/443/EEC) or equivalent data: … . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 77
▼M1
4.8.5. Diagram of the speedometer scale or other forms of display:
… ..........................................................
4.9. Tachograph: yes/no (1)

4.9.1 Approval mark: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.10. Differential lock: yes/no/optional (1)
▼M13
4.11. Gear shift indicator (GSI)
4.11.1. Acoustic indication available yes/no (1). If yes, description of
sound and sound level at the driver’s ear in dB(A). (Acoustic
indication always switchable on/off)
4.11.2. Information according to point 4.6 of Annex I to

Regulation (EU) No 65/2012 (manufacturer’s declared value)
4.11.3. Photographs and/or drawings of the gear shift indicator

instrument and brief description of the system components
and operation:
▼M1
5. AXLES
5.1. Description of each axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4. Position of retractable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5. Position of loadable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. SUSPENSION
6.1. Drawing of the suspension arrangements: … . . . . . . . . . . . . . . . .
6.2. Type and design of the suspension of each axle or group of

axles or wheel: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1. Level adjustment: yes/no/optional (1)

any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.3. Air-suspension for driving axle(s): yes/no (1)
6.2.3.1. Suspension of driving axle(s) equivalent to air-suspension:

yes/no (1)
6.2.3.2. Frequency and damping of the oscillation of the sprung mass:

… ..........................................................
6.2.4. Air-suspension for non-driving axle(s): yes/no (1)
6.2.4.1. Suspension of non-driving axle(s) equivalent to air-suspension:

yes/no (1)
6.2.4.2. Frequency and damping of the oscillation of the sprung mass:

… ..........................................................
6.3. Characteristics of the springing parts of the suspension

(design, characteristics of the materials and dimensions): … .
6.4. Stabilisers: yes/no/optional (1)
6.5. Shock absorbers: yes/no/optional (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 78
▼M27
6.6. Tyres and wheels
6.6.1. Tyre/wheel combination(s)
6.6.1.1. Axles
6.6.1.1.1. Axle 1: … . . . . . . . . . .
6.6.1.1.1.1. Tyre size designation: … . . .
6.6.1.1.1.2. Load-capacity index: … . . . .
6.6.1.1.1.3. Speed category symbol (r)
6.6.1.1.1.4. Wheel rim size(s): … . . . .
6.6.1.1.1.5. Wheel off-set(s): … . . . .
6.6.1.1.2. Axle 2: … . . . .
6.6.1.1.2.1. Tyre size designation: … . . . . . . . . .
6.6.1.1.2.2. Load-capacity index: … . . . .
6.6.1.1.2.3. Speed category symbol: …. . . .
6.6.1.1.2.4. Wheel rim size(s): … . . . .
6.6.1.1.2.5. Wheel off-set(s): … . . . .
etc.
6.6.1.2. Spare wheel, if any: … . . .
6.6.2. Upper and lower limits of rolling radii
6.6.2.1. Axle 1: … . . . . . . . . . . . . . . . . . . . mm
6.6.2.2. Axle 2: … . . . . . . . . . . . . . . . . . . . mm
6.6.2.3. Axle 3: … . . . . . . . . . . . . . . . . . . . mm
6.6.2.4. Axle 4: … . . . . . . . . . . . . . . . . . . . mm
etc.
6.6.3. Tyre pressure(s) as recommended by the vehicle manufacturer:

… . . . . . . . . . . . . . . . . . . kPa
6.6.4. Chain/tyre/wheel combination on the front and/or rear axle that

is suitable for the type of vehicle, as recommended by the
manufacturer: … . . . . . . . . . . . . . . . . . . .
6.6.5. Brief description of temporary use spare unit (if any): … . . .
▼M1
7. STEERING
7.1. Schematic diagram of steered axle(s) showing steering
geometry: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2. Transmission and control

7.2.1. Type of steering transmission (specify for front and rear, if
applicable): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2. Linkage to wheels (including other than mechanical means;

specify for front and rear, if applicable): … . . . . . . . . . . . . . . . . .
7.2.2.1. A brief description of the electrical/electronic components (if

any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.3. Method of assistance (if any): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.3.1. Method and diagram of operation, make(s) and type(s): … . .

02007L0046 — EN — 18.01.2018 — 021.001 — 79
▼M1
7.2.4. Diagram of the steering equipment as a whole, showing the
position on the vehicle of the various devices influencing its
steering behaviour: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.5. Schematic diagram(s) of the steering control(s): … . . . . . . . . . .
7.2.6. Range and method of adjustment (if any), of the steering

control: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3. Maximum steering angle of the wheels

7.3.1. To the right: … degrees; number of turns of the steering wheel
(or equivalent data): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3.2. To the left: … degrees; number of turns of the steering wheel

(or equivalent data): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. BRAKES
(The following particulars, including means of identification,
where applicable, are to be given)
8.1. Type and characteristics of the brakes as defined in point 1.6

of Annex I to Council Directive 71/320/EEC (OJ L 205,
6.9.1971, p. 37) including details and drawings of the
drums, discs, hoses make and type of shoe/pad assemblies
and/or linings, effective braking areas, radius of drums,
shoes or discs, mass of drums, adjustment devices, relevant
parts of the axle(s) and suspension: … . . . . . . . . . . . . . . . . . . . . . .
8.2. Operating diagram, description and/or drawing of the braking

system described in point 1.2 of Annex I to Directive
71/320/EEC including details and drawings of the transmission
and controls:
8.2.1. Service braking system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.2. Secondary braking system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.3. Parking braking system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.4. Any additional braking system: … . . . . . . . . . . . . . . . . . . . . . . . . . .
8.2.5. Break-away braking system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3. Control and transmission of trailer braking systems in vehicles

designed to tow a trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.4. Vehicle is equipped to tow a trailer with electric/pneumatic/

hydraulic (1) service brakes: yes/no (1)
8.5. Anti-lock braking system: yes/no/optional (1)
8.5.1. For vehicles with anti-lock systems, description of system

operation (including any electronic parts), electric block
diagram, hydraulic or pneumatic circuit plan: … . . . . . . . . . . . .
8.6. Calculation and curves according to the Appendix to

point 1.1.4.2 of the Appendix to Annex II to Directive
71/320/EEC or to the Appendix to Annex XI thereto, if
applicable: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 80
▼M1
8.7. Description and/or drawing of the energy supply, also to be
specified for power-assisted braking systems: … . . . . . . . . . . . .
8.7.1. In the case of compressed-air braking systems, working

pressure p2 in the pressure reservoir(s): … . . . . . . . . . . . . . . . . . .
8.7.2. In the case of vacuum braking systems, the initial energy level
in the reservoir(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8. Calculation of the braking system: Determination of the ratio

between the total braking forces at the circumference of the
wheels and the force applied to the braking control: … . . . . .
8.9. Brief description of the braking system according to point 1.6

of the Addendum to Appendix 1 of Annex IX to Directive
71/320/EEC: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.10. If claiming exemptions from the Type I and/or Type II

or Type III tests, state the number of the report in
accordance with Appendix 2 of Annex VII to Directive
71/320/EEC: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.11. Particulars of the type(s) of endurance braking system(s): …
9. BODYWORK
▼M27
9.1. Type of bodywork using the codes defined in Part C of
Annex II of Directive 2007/46/EC: … . . . . . . . . . . . . . . . . . . . . . .
▼M1
9.2. Materials used and methods of construction: … . . . . . . . . . . . . .
9.3. Occupant doors, latches and hinges

9.3.1. Door configuration and number of doors: … . . . . . . . . . . . . . . . .
9.3.1.1. Dimensions, direction and maximum angle of opening: … . .
9.3.2. Drawing of latches and hinges and of their position in the

doors: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.3.3. Technical description of latches and hinges: …. . . . . . . . . . . . . .
9.3.4. Details, including dimensions, of entrances, steps and

necessary handles where applicable: …. . . . . . . . . . . . . . . . . . . . . .
9.4. Field of vision

9.4.1. Particulars of the primary reference marks in sufficient detail
to enable them to be readily identified and the position of each
in relation to the others and to the R-point to be verified: …
9.4.2. Drawing(s) or photograph(s) showing the location of

component parts within the 180o forward field of vision: ….
9.5. Windscreen and other windows

9.5.1. Windscreen
9.5.1.1. Materials used: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.1.2. Method of mounting: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.1.3. Angle of inclination: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.1.4. Type-approval number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 81
▼M1
9.5.1.5. Windscreen accessories and the position in which they are
fitted together with a brief description of any electrical/elec
tronic components involved: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.2. Other windows

9.5.2.1. Materials used: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.2.3. A brief description of the electrical/electronic components (if

any) of the window lifting mechanism: … . . . . . . . . . . . . . . . . . .
9.5.3. Opening roof glazing

9.5.3.1. Materials used: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.5.4. Other glass panes

9.5.4.1. Materials used: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.6. Windscreen wiper(s)

9.6.1. Detailed technical description (including photographs or
drawings): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.7. Windscreen washer

drawings) or, if approved as separate technical unit,
type-approval number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.8. Defrosting and demisting

drawings): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.8.2. Maximum electrical consumption: … . . . . . . . . . . . . . . . . . . . kW
9.9. Devices for indirect vision

9.9.1. Rear-view mirrors, stating for each mirror:
9.9.1.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.2. Type-approval mark: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.3. Variant: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.4. Drawing(s) for the identification of the mirror showing the

position of the mirror relative to the vehicle structure: … . . .
9.9.1.5. Details of the method of attachment including that part of the

vehicle structure to which it is attached: … . . . . . . . . . . . . . . . . .
9.9.1.6. Optional equipment which may affect the rearward field of

vision: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.7. A brief description of the electronic components (if any) of the

adjustment system: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.2. Devices for indirect vision other than mirrors: … . . . . . . . . . . .
▼M27
9.9.2.1. Type and description of the device: … . . . . . . . . . . . . . . . . . . . . . .
▼M1
9.9.2.1.1. In the case of a camera-monitor device, the detection distance
(mm), contrast, luminance range, glare correction, display
performance (black and white/colour), image repetition
frequency, luminance reach of the monitor: … . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 82
▼M1
9.9.2.1.2. Sufficiently detailed drawings to identify the complete device,
including installation instructions; the position for the EC
type-approval mark has to be indicated on the drawings.
9.10. Interior arrangement

9.10.1. Interior protection for occupants
9.10.1.1. Layout drawing or photographs showing the position of the
attached sections or views: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.1.2. Photograph or drawing showing the reference zone including

the exempted area referred to in point 2.3.1 of Annex I to
Council Directive 74/60/EEC (OJ L 38, 11.2.1974, p. 2): …
9.10.1.3. Photographs, drawings and/or an exploded view of the interior

fittings, showing the parts in the passenger compartment and
the materials used (with the exception of interior rear view
mirrors), arrangement of controls, roof and opening roof,
backrest, seats and the rear part of seats: … . . . . . . . . . . . . . . . .
9.10.2. Arrangement and identification of controls, tell-tales and

indicators
9.10.2.1. Photographs and/or drawings of the arrangement of symbols
and controls, tell-tales and indicators: … . . . . . . . . . . . . . . . . . . . .
9.10.2.2. Photographs and/or drawings of the identification of controls,

tell-tales and indicators and of the vehicle parts referred to in
Annex II and III of Directive 78/316/EEC where relevant: …
9.10.2.3. Summary table

The vehicle is equipped with the following controls, indicators
and tell-tales pursuant to Annexes II and III to Directive
78/316/EEC
Controls, tell-tales and indicators for which, when fitted, identification is mandatory, and
symbols to be used for that purpose
Control/ Identified Identified

Symbol Tell-tale
Device indicator by Where (**) by Where (**)
No available (*)
available (*) symbol (*) symbol (*)
1 Master light
2 Dipped-beam
headlamps
3 Main-beam
headlamps
4 Position (side)
lamps
5 Front fog lamps
6 Rear fog lamp
7 Headlamp
levelling device
8 Parking lamps
02007L0046 — EN — 18.01.2018 — 021.001 — 83
▼M1
Symbol Tell-tale
No available (*)
9 Direction
indicators
10 Hazard warning
11 Windscreen
wiper
12 Windscreen
washer
13 Windscreen
wiper and
washer
14 Headlamp
cleaning device
15 Windscreen
demisting and
defrosting
16 Rear window
demisting and
defrosting
17 Ventilating fan
18 Diesel pre-heat
19 Choke
20 Brake failure
21 Fuel level
22 Battery
charging
condition
23 Engine coolant
temperature
(*) x = yes
— = no or not separately available
o = optional.
(**) d = directly on control, indicator or tell-tale
c = in close vicinity.
02007L0046 — EN — 18.01.2018 — 021.001 — 84
▼M1
Controls, tell-tales and indicators for which, when fitted, identification is optional, and symbols
which shall be used if they are to be identified

Symbol Tell-tale
No available (*)
1 Parking brake
2 Rear window
wiper
3 Rear window
washer
4 Rear window
wiper and
washer
5 Intermittent
windscreen
wiper
6 Audible
warning device
(horn)
7 Front hood
(bonnet)
8 Rear hood
(boot)
9 Seat-belt
10 Engine oil
pressure
11 Unleaded petrol
(*) x = yes
— = no or not separately available
o = optional.
(**) d = directly on control, indicator or tell-tale
c = in close vicinity.
9.10.3. Seats
9.10.3.1. Number of seating positions (s): … . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.1.1. Location and arrangement: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.2. Seat(s) designated for use only when the vehicle is stationary:
… ..........................................................
9.10.3.3. Mass: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.4. Characteristics: for seats not type-approved as components,

description and drawings of
02007L0046 — EN — 18.01.2018 — 021.001 — 85
▼M1
9.10.3.4.1. The seats and their anchorages: … . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.4.2. The adjustment system: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.4.3. The displacement and locking systems: … . . . . . . . . . . . . . . . . . .
9.10.3.4.4. The seat-belt anchorages (if incorporated in the seat structure):

… ..........................................................
9.10.3.4.5. The parts of the vehicle used as anchorages: … . . . . . . . . . . . . .
9.10.3.5. Coordinates or drawing of the R-point (t)
9.10.3.5.1. Driver's seat: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.5.2. All other seating positions: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.6. Design torso angle
9.10.3.6.1. Driver's seat: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.7. Range of seat adjustment
9.10.3.7.1. Driver's seat: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.4. Head restraints

9.10.4.1. Type(s) of head restraints: integrated/detachable/separate (1)
9.10.4.2. Type-approval number(s), if available: … . . . . . . . . . . . . . . . . . . .
9.10.4.3. For head restraints not yet approved
9.10.4.3.1. A detailed description of the head restraint, specifying in

particular the nature of the padding material or materials
and, where applicable, the position and specifications of the
braces and anchorage pieces for the type of seat for which
approval is sought: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.4.3.2. In the case of a ‘separate’ head restraint
9.10.4.3.2.1. A detailed description of the structural zone to which the head

restraint is intended to be fixed: … . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.4.3.2.2. Dimensional drawings of the characteristic parts of the

structure and the head restraint: … . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.5. Heating systems for the passenger compartment

9.10.5.1. A brief description of the vehicle type with regard to the
heating system if the heating system uses the heat of the
engine cooling fluid: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.5.2. A detailed description of the vehicle type with regard to the

heating if the cooling air or the exhaust gases of the engine are
used as heat source, including:
9.10.5.2.1. Layout drawing of the heating system showing its position in

the vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.5.2.2. Layout drawing of the heat exchanger for heating systems

using the exhaust gases for heating, or of the parts where
the heat exchange takes place (for heating systems using the
engine cooling air for heating): … . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 86
▼M1
9.10.5.2.3. Sectional drawing of the heat exchanger or the parts
respectively where the heat exchange takes place indicating
the thickness of the wall, used materials and characteristics
of the surface: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.5.2.4. Specifications shall be given for further important components

of the heating system such as, for example, the heater fan, with
regard to their method of construction and technical data: …
9.10.5.3. A brief description of the vehicle type with regard to the

combustion heating system and the automatic control: …. . . .
9.10.5.3.1. Layout drawing of the combustion heater, the air inlet system,
the exhaust system, the fuel tank, the fuel supply system
(including the valves) and the electrical connections showing
their positions in the vehicle.
9.10.5.4. Maximum electrical consumption: …… . . . . . . . . . . . . . . . . kW
9.10.6. Components influencing the behaviour of the steering

mechanism in the event of an impact
9.10.6.1. A detailed description, including photograph(s) and/or
drawing(s), of the vehicle type with respect to the structure,
the dimensions, the lines and the constituent materials of that
part of the vehicle forward of the steering control, including
those components designed to contribute to the absorption of
energy in the event of an impact against the steering control:
… ..........................................................
9.10.6.2. Photograph(s) and/or drawing(s) of vehicle components other

than those described in 9.10.6.1 as identified by the manu
facturer in agreement with the technical service, as
contributing to the behaviour of the steering mechanism in
case of impact: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7. Burning behaviour of materials used in the interior

construction of certain categories of motor vehicles
9.10.7.1. Material(s) used for the interior lining of
the roof
9.10.7.1.1. Component type-approval number(s), if available: … . . . . . . . .
9.10.7.1.2. For materials not approved
9.10.7.1.2.1. Base material(s)/designation: …… . . . . . . . . . . /…… . . . . . . . . . .
9.10.7.1.2.2. Composite/single (1) material, number of layers (1): … . . . . . . .
9.10.7.1.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.1.2.4. Maximum/minimum thickness: …… . . . . . . /…… . . . . . . mm
9.10.7.2. Material(s) used for the rear and side walls

02007L0046 — EN — 18.01.2018 — 021.001 — 87
▼M1
9.10.7.2.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.3. Material(s) used for the floor

9.10.7.3.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.4. Material(s) used for the upholstery of the

seats
9.10.7.4.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.5. Material(s) used for the heating and venti

lation pipes
9.10.7.5.2.1. Base material(s)/designation: …… . . . . . . . . . . . /.…... . . . . . . . . . .
9.10.7.5.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.5.2.4. Maximum/minimum thickness: …… . . . . . . /……. . . . . . . mm
9.10.7.6. Material(s) used for luggage racks

9.10.7.6.2.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.7. Material(s) used for other purposes

9.10.7.7.1. Intended purposes: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 88
▼M1
9.10.7.7.3.3. Type of coating (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.7.7.3.4. Maximum/minimum thickness: …. . . . . . . . . /…. . . . . . . . . mm
9.10.7.8. Components approved as complete devices

(seats, separation walls, luggage racks,
etc.)
9.10.7.8.1. Component type-approval number(s): …. . . . . . . . . . . . . . . . . . . . .
9.10.7.8.2. For the complete device: seat, separation wall, luggage racks,
etc. (1)
9.10.8 Gas used as refrigerant in the air-conditioning system: … . .

9.10.8.1 The air-conditioning system is designed to contain fluorinated
greenhouse gases with global warming potential higher than
150: yes/no (1)
9.10.8.2. If yes, fill in the following sections
9.10.8.2.1. Drawing and brief description of the air-conditioning system,

including the reference or part number and material of the leak
components;
9.10.8.2.2. Leakage of the air-conditioning system
9.10.8.2.4. Reference or part number and material of the components of

the system and information about the test (e.g. test report
number, approval number, etc.): … . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.8.3. Overall leakage in g/year of the entire system: … . . . . . . . . . . .
9.11. External projections

9.11.1. General arrangement (drawing or photographs) indicating the
position of the attached sections and views:
9.11.2. Drawings and/or photographs, for example, and where

relevant, of the door and window pillars, air-intake grilles,
radiator grille, windscreen wipers, rain gutter channels,
handles, slide rails, flaps, door hinges and locks, hooks,
eyes, decorative trim, badges, emblems and recesses and any
other external projections and parts of the exterior surface
which can be regarded as critical (e.g. lighting equipment).
If the parts listed in the previous sentence are not critical,
for documentation purposes they may be replaced by
photographs, accompanied if necessary by dimensional
details and/or text:
9.11.3. Drawings of parts of the external surface in accordance with

Annex I, item 6.9.1 to Directive 74/483/EEC: …. . . . . . . . . . . .
9.11.4. Drawing of bumpers: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.11.5. Drawing of the floor line: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 89
▼M1
9.12. Safety belts and/or other restraint systems
9.12.1. Number and position of safety belts and restraint systems and
seats on which they can be used
(L = left-hand side, R = right-hand side, C = centre)
Belt adjustment device

Complete EC Variant, if
for height (indicate yes/
type-approval mark applicable
no/optional)
8
>
> L
>
>
<
First row of seats C
>
>
>
>
:
R
8
>
> L
>
>
<
Second row of seats (*) C
>
>
>
>
:
R
(*) The table may be extended as necessary for vehicles with more than two rows of seats or if there are more than
three seats across the width of the vehicle.
9.12.2. Nature and position of supplementary restraint systems

(indicate yes/no/optional)
Front airbag Side airbag Belt pre-loading device

8
>
> L
>
>
<
>
>
>
>
:
R
8
>
> L
>
>
<
>
>
>
>
:
R
three seats across the width of the vehicle
9.12.3. Number and position of safety belt anchorages and proof of

compliance with Directive 76/115/EEC, (i.e. type-approval
number or test report): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.13. Safety belt anchorages

9.13.1. Photographs and/or drawings of the bodywork showing the
position and dimensions of the actual and the effective
anchorages including the R-points: … . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 90
▼M1
9.13.2. Drawings of the belt anchorages and parts of the vehicle
structure where they are attached (with the material indication):
… ..........................................................
9.13.3. Designation of the types (u) of safety belt authorised for fitting
to the anchorages with which the vehicle is equipped
Anchorage location
Vehicle
Seat structure
structure
First row of seats
8 Á
< Lower anchorages
> outboard inboard
Right-hand seat
>
:
Upper anchorages
8 Á
< Lower anchorages
> right left
Centre seat
>
:
Upper anchorages
8 Á
< Lower anchorages
> outboard inboard
Left-hand seat
>
:
Upper anchorages
Second row of seats (*)
8 Á
< Lower anchorages
> outboard inboard
Right-hand seat
>
:
Upper anchorages
8 Á
< Lower anchorages
> right left
Centre seat
>
:
Upper anchorages
8 Á
>
> Lower anchorages outboard inboard
>
<
Left-hand seat >
>
>
:
Upper anchorages
9.13.4. Description of a particular type of safety belt where an

anchorage is located in the seat backrest or incorporates an
energy dissipating device: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.14. Space for mounting rear registration plates (give range

where appropriate, drawings may be used where
applicable)
9.14.1. Height above road surface, upper edge: … . . . . . . . . . . . . . . . . . .
9.14.2. Height above road surface, lower edge: … . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 91
▼M1
9.14.3. Distance of the centre line from the longitudinal median plane
of the vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.14.4. Distance from the left vehicle edge: … . . . . . . . . . . . . . . . . . . . . .
9.14.5. Dimensions (length × width): … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.14.6. Inclination of the plane to the vertical: … . . . . . . . . . . . . . . . . . . .
9.14.7. Angle of visibility in the horizontal plane: … . . . . . . . . . . . . . . .
9.15. Rear under-run protection

9.15.0. Presence: yes/no/incomplete (1)
9.15.1. Drawing of the vehicle parts relevant to the rear under-run

protection, i.e. drawing of the vehicle and/or chassis with
position and mounting of the widest rear axle, drawing of
the mounting and/or fitting of the rear under-run protection.
If the under-run protection is not a special device, the drawing
shall clearly show that the required dimensions are met: … .
9.15.2. In case of a special device, full description and/or drawing of

the rear under-run protection (including mountings and
fittings), or, if approved as separate technical unit,
9.16. Wheel guards

9.16.1. Brief description of the vehicle with regard to its wheel
guards: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.16.2. Detailed drawings of the wheel guards and their position on

the vehicle showing the dimensions specified in Figure 1 of
Annex I to Directive 78/549/EEC and taking account of the
extremes of tyre/wheel combinations: … . . . . . . . . . . . . . . . . . . . .
9.17. Statutory plates

9.17.1. Photographs and/or drawings of the locations of the statutory
plates and inscriptions and of the vehicle identification
number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.17.2. Photographs and/or drawings of the statutory plate and

inscriptions (completed example with dimensions): … . . . . . . .
9.17.3. Photographs and/or drawings of the vehicle identification

number (completed example with dimensions): … . . . . . . . . . . .
9.17.4. Manufacturer's declaration of compliance with the

requirements set out in point 3.1.1.1 of Annex to Council
Directive 76/114/EEC (OJ L 24, 30.1.1976, p. 1)
9.17.4.1. The meaning of characters in the second section and, if

applicable, in the third section used to comply with the
requirements of section 5.3 of ISO Standard 3779-1983 shall
be explained: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.17.4.2. If characters in the second section are used to comply with the
requirements of section 5.4 of ISO Standard 3779-1983 these
characters shall be indicated: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 92
▼M1
9.18. Radio interference/electromagnetic compatibility
9.18.1. Description and drawings/photographs of the shapes and
constituent materials of the part of the body forming the
engine compartment and the part of the passenger
compartment nearest to it: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.18.2. Drawings or photographs of the position of metal components

housed in the engine compartment (e.g. heating appliances,
spare wheel, air filter, steering mechanism, etc.): … . . . . . . . . .
9.18.3. Table and drawing of radio-interference control equipment: …
9.18.4. Particulars of the nominal value of the direct current resistance,

and, in the case of resistive ignition cables, of their nominal
resistance per metre: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.19. Lateral protection

9.19.1. Drawing of the vehicle parts relevant to the lateral protection,

i.e. drawing of the vehicle and/or chassis with position and
mounting of the axle(s), drawing of the mountings and/or the
fittings of lateral protection device(s). If the lateral protection
is achieved without lateral protection device(s) the drawing
shall clearly show that the required dimensions are met: … .
9.19.2. In the case of lateral protection device(s), full description

and/or drawing of such device(s) (including mountings and
fittings) or its/their component type-approval number(s): …. .
9.20. Spray-suppression system

9.20.1. Brief description of the vehicle with regard to its

spray-suppression system and the constituent components: …
9.20.2. Detailed drawings of the spray-suppression system and its

position on the vehicle showing the dimensions specified in
the figures in Annex III to Directive 91/226/EEC and taking
account of the extremes of tyre/wheel combinations: … . . . . .
9.20.3. Type-approval number(s) of spray-suppression device(s), if

available: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.21. Side-impact resistance

9.21.1. A detailed description, including photographs and/or drawings,
of the vehicle with respect to the structure, the dimensions, the
lines and the constituent materials of the side walls of the
passenger compartment (exterior and interior), including
specific details of the protection system, where applicable: …
02007L0046 — EN — 18.01.2018 — 021.001 — 93
▼M1
9.22. Front under-run protection
9.22.1. Drawing of the vehicle parts relevant to the front under-run

protection, i.e. drawing of the vehicle and/or chassis with
position and mounting and/or fitting of the front under-run
protection. If the under-run protection is no special device,
the drawing shall clearly show that the required dimensions
are met: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.22.2. In the case of special device, full description and/or drawing of

the front under-run protection (including mountings and
fittings), or, if approved as a separate technical unit,
9.23. Pedestrian protection

relevant reference lines and the constituent materials of the
frontal part of the vehicle (interior and exterior), including
detail of any active protection system installed.
▼M2
9.24. Frontal protection systems
9.24.1. General arrangement (drawings or photographs) indicating the

position and attachment of the frontal protection systems:
9.24.2. Drawings and/or photographs, where relevant, of air intake

grilles, radiator grille, decorative trim, badges, emblems and
recesses and any other external projections and parts of the
exterior surface which can be regarded as critical (e.g. lighting
equipment). If the parts listed in the first sentence are not
critical, for documentation purposes they may be replaced by
photographs, accompanied if necessary by dimensional details
and/or text:
9.24.3. Complete details of fittings required and full instructions,

including torque requirements, for fitting:
9.24.4. Drawing of bumpers:
9.24.5. Drawing of the floor line at the vehicle front end:
▼M1
10. LIGHTING AND LIGHT SIGNALLING DEVICES
10.1. Table of all devices: number, make, model, type-approval
mark, maximum intensity of main-beam headlamps, colour,
tell-tale: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.2. Drawing of the position of lighting and light signalling

devices: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3. For every lamp and reflector specified in Council Directive

76/756/EEC (OJ L 262, 27.9.1976, p. 1) supply the
following information (in writing and/or by diagram)
02007L0046 — EN — 18.01.2018 — 021.001 — 94
▼M1
10.3.1. Drawing showing the extent of the illuminating surface: … .
10.3.2. Method used for the definition of the apparent surface in

accordance with paragraph 2.10 of UNECE Regulation
No 48 (OJ L 137, 30.5.2007, p. 1): … . . . . . . . . . . . . . . . . . . . . .
10.3.3. Axis of reference and centre of reference: …. . . . . . . . . . . . . . . .
10.3.4. Method of operation of concealable lamps: …. . . . . . . . . . . . . . .
10.3.5. Any specific mounting and wiring provisions: …. . . . . . . . . . . .
10.4. Dipped beam lamps: normal orientation in accordance to

paragraph 6.2.6.1 of UNECE Regulation No 48:
10.4.1. Value of initial adjustment: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4.2. Location of indication: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10.4.3. Description/drawing (1) and type of >
>
>
>
headlamp levelling device (e.g. >
>
automatic, stepwise manually >
>
>
>
adjustable, continuously manually >
>
>
>
adjustable): >
>
>
>
>
= Applicable only for
10.4.4. Control device: > vehicles with headlamp
>
> levelling device
>
>
>
>
10.4.5. Reference marks: >
>
>
>
>
>
>
>
>
10.4.6. Marks assigned for loading >
>
>
;
conditions:
10.5. A brief description of electrical/electronic components other

than lamps (if any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11. CONNECTIONS BETWEEN TOWING VEHICLES AND

TRAILERS AND SEMI-TRAILERS
11.1. Class and type of the coupling device(s) fitted or to be fitted:
… ..........................................................
11.2. Characteristics D, U, S and V of the coupling device(s) fitted

or minimal characteristics D, U, S and V of the coupling
device(s) to be fitted: …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . daN
11.3. Instructions for attachment of the coupling type to the vehicle

and photographs or drawings of the fixing points at the vehicle
as stated by the manufacturer; additional information, if the
use of the coupling type is restricted to certain variants or
versions of the vehicle type: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4. Information of the fitting of special towing brackets or

mounting plates: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5. Type-approval number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12. MISCELLANEOUS
12.1. Audible warning device(s)
02007L0046 — EN — 18.01.2018 — 021.001 — 95
▼M1
12.1.1. Location, method of affixing, placement and orientation of the
device(s), with dimensions: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.2. Number of device(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.3. Type-approval number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.4. Electrical/pneumatic (1) circuit diagram: … . . . . . . . . . . . . . . . . . .
12.1.5. Rated voltage or pressure: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.1.6. Drawing of the mounting device: … . . . . . . . . . . . . . . . . . . . . . . . .
12.2. Devices to prevent unauthorised use of the vehicle
12.2.1. Protective device
12.2.1.1. A detailed description of the vehicle type with regard to the

arrangement and design of the control or of the unit on which
the protective device acts: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2.1.2. Drawings of the protective device and of its mounting on the

vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.2.1.3. A technical description of the device: … . . . . . . . . . . . . . . . . . . . .
12.2.1.4. Details of the lock combinations used: … . . . . . . . . . . . . . . . . . . .
12.2.1.5. Vehicle immobiliser
12.2.1.5.1. Type-approval number, if available: … . . . . . . . . . . . . . . . . . . . . . .
12.2.1.5.2. For immobilisers not yet approved
12.2.1.5.2.1. A detailed technical description of the vehicle immobiliser and

of the measures taken against inadvertent activation: … . . . . .
12.2.1.5.2.2. The system(s) on which the vehicle immobiliser acts: … . . . .
12.2.1.5.2.3. Number of effective interchangeable codes, if applicable: ….
12.2.2. Alarm system (if any)
12.2.2.1. Type-approval number, if available: … . . . . . . . . . . . . . . . . . . . . . .
12.2.2.2. For alarm systems not yet approved
12.2.2.2.1. A detailed description of the alarm system and of the vehicle

parts related to the alarm system installed: … . . . . . . . . . . . . . . .
12.2.2.2.2. A list of the main components comprising the alarm system:

… ..........................................................

any): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.3. Towing device(s)
12.3.1. Front: Hook/eye/other (1)
12.3.2. Rear: Hook/eye/other/none (1)
12.3.3. Drawing or photograph of the chassis/area of the vehicle body

showing the position, construction and mounting of the towing
device(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 96
▼M1
12.4. Details of any non-engine related devices designed to
influence fuel consumption (if not covered by other items): …
12.5. Details of any non-engine related devices designed to reduce

noise (if not covered by other items): … . . . . . . . . . . . . . . . . . . . .
12.6. Speed limitation devices
12.6.1. Manufacturer(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.6.2. Type(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12.6.3. Type-approval number(s), if available: … . . . . . . . . . . . . . . . . . . .
12.6.4. Speed or range of speeds at which the speed limitation may be

set: ……. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . km/h
12.7. Table of installation and use of RF transmitters in the

vehicle(s), if applicable: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Antenna position at vehicle, specific conditions for

Frequency bands (Hz) Maximum output power (W)
installation and/or use
The applicant for type-approval shall also supply, where

appropriate:
Appendix 1
A list containing make and type of all electrical and/or elec

tronic components concerned by Commission Directive
72/245/EEC (OJ L 152, 6.7.1972, p. 15).
Appendix 2
Schematics or drawing of the general arrangement of electrical

and/or electronic components concerned by Directive
72/245/EEC and the general wiring harness arrangement.
Appendix 3
Description of vehicle chosen to represent the type
Body style:
Left- or right-hand drive (1)
Wheelbase:
Appendix 4
Relevant test report(s) supplied by the manufacturer or

approved/recognised laboratories for the purpose of drawing
up the type-approval certificate
12.7.1. Vehicle equipped with a 24 GHz short-range radar equipment:

yes/no (1)
13. SPECIAL PROVISIONS FOR BUSES AND COACHES

13.1. Class of vehicle: Class I/Class II/Class III/Class A/Class B (1)
02007L0046 — EN — 18.01.2018 — 021.001 — 97
▼M1
13.1.1. Type-approval number of bodywork approved as a separate
technical unit: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.1.2. Chassis types where the type-approved bodywork can be

installed (manufacturer(s), and types of incomplete vehicle): …
13.2. Area for passengers (m2)

13.2.1. Total (S0): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2.2. Upper deck (S0a) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2.3. Lower deck (S0b) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.2.4. For standing passengers (S1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3. Number of passengers (seated and standing)

13.3.1. Total (N): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3.2. Upper deck (Na) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3.3. Lower deck (Nb) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4. Number of passengers seated

13.4.1. Total (A): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.2. Upper deck (Aa) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.3. Lower deck (Ab) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.4. Number of wheelchair positions for category M2 and M3

vehicles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.5. Number of service doors: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.6. Number of emergency exits (doors, windows, escape hatches,

intercommunication staircase and half staircase): … . . . . . . . . .
13.6.1. Total: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.6.2. Upper deck (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.6.3. Lower deck (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.7. Volume of luggage compartments (m3): … . . . . . . . . . . . . . . . .
13.8. Area of luggage transportation on the roof (m2): … . . . . . .
13.9. Technical devices facilitating the access to vehicles (e.g.

ramp, lifting platform, kneeling system), if fitted: … . . . . . . . .
13.10. Strength of superstructure

13.10.1. Type-approval number, if available: … . . . . . . . . . . . . . . . . . . . . . .
13.10.2. For superstructures not yet approved
13.10.2.1. Detailed description of the superstructure of the vehicle type

including its dimensions, configuration and constituent
materials and its attachment to any chassis frame: …. . . . . . . .
13.10.2.2. Drawings of the vehicle and those parts of its interior

arrangement which have an influence on the strength of the
superstructure or on the residual space: … . . . . . . . . . . . . . . . . . .
13.10.2.3. Position of centre of gravity of the vehicle in running order in

the longitudinal, transverse and vertical directions: … . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 98
▼M1
13.10.2.4. Maximum distance between the centre lines of the outboard
passenger seats: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.11. Points of Directive 2001/85/EC of the European parliament

and of the Council (OJ L 42, 13.2.2002, p. 1) to be accom
plished and demonstrated for this technical unit: … . . . . . .
▼M15
13.12. Drawing with dimensions showing the interior
arrangement as regards the seating positions, area for
standees, wheelchair user(s), luggage compartments
including racks and ski-box, if any
▼M1
14. SPECIAL PROVISIONS FOR VEHICLES INTENDED FOR
THE TRANSPORT OF DANGEROUS GOODS
14.1. Electrical equipment according to Council Directive
94/55/EC (OJ L 319, 12.12.1994, p. 1)
14.1.1. Protection against overheating of conductors: …. . . . . . . . . . . . .
14.1.2. Type of circuit breaker: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1.3. Type and operation of battery master switch: … . . . . . . . . . . . .
14.1.4. Description and location of safety barrier for tachograph: …
14.1.5. Description of permanently energised installations. Indicate the

EN standard applied: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.1.6. Construction and protection of electrical installation situated to

the rear of the driver's compartment: … . . . . . . . . . . . . . . . . . . . . .
14.2. Prevention of fire risks

14.2.1. Type of not readily flammable material in the driver's
compartment: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2.2. Type of heat shield behind the driver's compartment (if

applicable): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2.3. Position and heat protection of engine: …. . . . . . . . . . . . . . . . . . .
14.2.4. Position and heat protection of the exhaust system: … . . . . . .
14.2.5. Type and design of the endurance braking systems heat

protection: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.2.6. Type, design and position of combustion heaters: … . . . . . . . .
14.3. Special requirements for bodywork, if any, according to

Directive 94/55/EC
14.3.1. Description of measures to comply with the requirements for
Type EX/II and Type EX/III vehicles: … . . . . . . . . . . . . . . . . . . .
14.3.2. In the case of Type EX/III vehicles, resistance against heat

from the outside: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15. REUSABILITY, RECYCLABILITY AND RECOVER

ABILITY
15.1. Version to which the reference vehicle belongs: …. . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 99
▼M1
15.2. Mass of the reference vehicle with bodywork or mass of the
chassis with cab, without bodywork and/or coupling device if
the manufacturer does not fit the bodywork and/or coupling
device (including liquids, tools, spare wheel, if fitted) without
driver: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3. Mass of materials of the reference vehicle: …. . . . . . . . . . . . . . .
15.3.1. Mass of material taken into account at the pre-treatment

step (v): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.2. Mass of the material taken into account at the dismantling

step (v): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.3. Mass of material taken into account at the non-metallic residue

treatment step, considered as recyclable (v): … . . . . . . . . . . . . . .
15.3.4. Mass of material taken into account at the non-metallic residue

treatment step, considered as energy recoverable (v): … . . . . . .
15.3.5. Materials breakdown (v): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.6. Total mass of materials, which are reusable and/or recyclable:

… ..........................................................
15.3.7. Total mass of materials, which are reusable and/or recoverable:

… ..........................................................
15.4. Rates
15.4.1. Recyclability rate ‘Rcyc’ (%): … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.4.2. Recoverability rate ‘Rcov’ (%): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
16. ACCESS TO VEHICLE REPAIR AND MAINTENANCE

INFORMATION
16.1. Address of principal website for access to vehicle repair and
maintenance information: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.1.1. Date from which it is available (no later than 6 months from
the date of type-approval): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.2. Terms and conditions of access to website: … . . . . . . . . . . . . . .
16.3. Format of the vehicle repair and maintenance information

accessible through website: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanatory notes
▼M15
(*) OJ L 353, 21.12.2012, p. 31.
▼M1
(1) Delete where not applicable (there are cases where nothing needs to be deleted when
more than one entry is applicable).
(2) Specify the tolerance.
(3) Please fill in here the upper and lower values for each variant.
(4) Only for the purpose of definition of off-road vehicles.
(5) Set out in such a way as to make the actual value clear for each technical
configuration of the vehicle type.
02007L0046 — EN — 18.01.2018 — 021.001 — 100
▼M1
(6) Vehicles can be fuelled with both petrol and a gaseous fuel but, where the petrol
system is fitted for emergency purposes or starting only and of which the petrol tank
cannot contain more than 15 litres of petrol, will be regarded for the test as vehicles
which can only run a gaseous fuel.
▼M15
(7) Optional equipment that affects the dimensions of the vehicle shall be specified.
▼M21
(8) To be documented in case of a single OBD engine family and if not already included
in the documentation package(s) referred to in point 3.2.12.2.7.0.4.
(9) Value for the combined WHTC including cold and hot part in accordance with
Annex VIII to Regulation (EU) No 582/2011.
(10) To be documented if not already included in the documentation referred to in

point 3.2.12.2.7.0.5.
▼M1
(a) If a part has been type-approved, that part need not be described if reference is made
to such approval. Similarly, a part need not be described if its construction is clearly
apparent from the attached diagrams or drawings. For each item for which drawings
or photographs shall be attached, give numbers of the corresponding attached
documents.
(b) If the means of identification of type contains characters not relevant to describe the
vehicle, component or separate technical unit types covered by this information
document, such characters shall be represented in the documentation by the symbol
‘?’ (e.g. ABC??123??).
(c) Classified according to the definitions set out in Part A of Annex II.
(d) Designation according to EN 10027-1: 2005. If that is not possible, the following
information shall be provided:
— description of the material,
— yield point,
— ultimate tensile stress,
— elongation (in %),
— Brinell hardness.
(e) ‘Forward control’ as defined in point 2.7 of Annex I to Council Directive 74/297/EEC
(OJ L 165, 20.6.1974, p. 16).
(f) Where there is one version with a normal cab and another with a sleeper cab, both
sets of masses and dimensions are to be stated.
(g) Standard ISO 612: 1978 — Road vehicles — Dimensions of motor vehicles and
towed vehicles — terms and definitions.
(g1) Motor vehicle and drawbar trailer: term No 6.4.1.

Semi-trailer and centre-axle trailer: term No 6.4.2.
Note:
In the case of a centre-axle trailer, the axis of the coupling shall be considered as the
foremost axle.
(g2) Term No 6.19.2.
(g3) Term No 6.20.
(g4) Term No 6.5.
(g5) Term No 6.1 and for vehicles other than those of category M1: point 2.4.1 of Annex I
to Directive 97/27/EC of the European Parliament and of the Council (OJ L 233,
25.8.1997, p. 1).
In the case of trailers, the lengths shall be specified as mentioned in term No 6.1.2 of
Standard ISO 612: 1978.
(g6) Term No 6.17.
to Directive 97/27/EC.
02007L0046 — EN — 18.01.2018 — 021.001 — 101
▼M1
to Directive 97/27/EC.
(g9) Term No 6.6.
(g10) Term No 6.10.
(g11) Term No 6.7.
(g12) Term No 6.11.
(g13) Term No 6.18.1.
(g14) Term No 6.9.
▼M15
(h) The mass of the driver is assessed at 75 kg.
The liquid containing systems (except those for used water that must remain empty)
are filled to 100 % of the capacity specified by the manufacturer.
The information referred to in points 2.6(b) and 2.6.1(b) do not need to be provided
for vehicle categories N2, N3, M2, M3, O3, and O4.
▼M1
(i) For trailers or semi-trailers, and for vehicles coupled with a trailer or a semi-trailer,
which exert a significant vertical load on the coupling device or the fifth wheel, this
load, divided by standard acceleration of gravity, is included in the maximum
technically permissible mass.
(j) ‘Coupling overhang’ is the horizontal distance between the coupling for centre-axle
trailers and the centreline of the rear axle(s).
(k) In the case of a vehicle that can run either on petrol, diesel, etc., or also in combi
nation with another fuel, items shall be repeated.
In the case of non-conventional engines and systems, particulars equivalent to those
referred to here shall be supplied by the manufacturer.
(l) This figure shall be rounded off to the nearest tenth of a millimetre.
(m) This value shall be calculated (π = 3,1416) and rounded off to the nearest cm3.
▼M20
(n) Determined in accordance with the requirements of Regulation (EC) No 715/2007 or
Regulation (EC) No 595/2009 as applicable.
▼M1
(o) Determined in accordance with the requirements of Council Directive 80/1268/EEC
(OJ L 375, 31.12.1980, p. 36).
(p) The specified particulars are to be given for any proposed variants.
(q) With respect to trailers, maximum speed permitted by the manufacturer.
(r) For tyres of category Z intended to be fitted on vehicles whose maximum speed
exceeds 300 km/h equivalent information shall be provided.
(s) The number of seating positions to be mentioned shall be the one when the vehicle is
in motion. A range can be specified in case of modular arrangement.
(t) ‘R-point’ or ‘seating reference point’ means a design point defined by the vehicle
manufacturer for each seating position and established with respect to the
three-dimensional reference system as specified in Annex III to Council Directive
77/649/EEC (OJ L 267, 19.10.1977, p. 1).
(u) For symbols and marks to be used, see Annex III, items 1.1.3 and 1.1.4 to Council
Directive 77/541/EEC (OJ L 220, 29.8.1977, p. 95). In the case of ‘S’ type belts,
specify the nature of the type(s).
(v) These terms are defined in the standard ISO 22628: 2002 — Road vehicles —
recyclability and recoverability — calculation method.
02007L0046 — EN — 18.01.2018 — 021.001 — 102
▼M18
__________
(w) Eco-innovations.
w1
( ) Expand the table if necessary, using one extra row per eco-innovation.
(w2) Number of the Commission Decision approving the eco-innovation.
(w3) Assigned in the Commission Decision approving the eco-innovation.
(w4) Under agreement of the type-approval authority, if a modelling methodology is

applied instead of the type 1 test cycle, this value shall be the one provided by the
modelling methodology.
(w5) Sum of the CO2 emissions savings of each individual eco-innovation.
▼M21
(x) Dual-fuel engines.
(x1) In case of a dual-fuel engine or vehicle.
(x2) In the case of Type 1B, Type 2B, and Type 3B of dual-fuel engines.
(x3) Except for dual-fuel engines or vehicles.

02007L0046 — EN — 18.01.2018 — 021.001 — 103
▼M12
ANNEX II
GENERAL DEFINITIONS, CRITERIA FOR VEHICLE CATEGORISATION,

VEHICLE TYPES AND TYPES OF BODYWORK
INTRODUCTORY PART
General definitions and general provisions
1. Definitions
1.1. ‘Seating position’ means any location capable of accommodating one
person seated who is at least as large as:
(a) the manikin of the 50th percentile male in the case of the driver;
(b) the manikin of the 5th percentile adult female in all other cases.
1.2. ‘Seat’ means a complete structure with trim, integral or not with the
vehicle body structure, which is intended to seat one person.
1.2.1. The term ‘seat’ covers both an individual seat and a bench seat.
1.2.2. Folding seats and removable seats are included in this definition.
1.3. ‘Goods’ means primarily any movable things.
The term ‘goods’ includes products in bulk, manufactured goods,

liquids, living animals, crops, indivisible loads.
1.4. ‘Maximum mass’ means the ‘technically permissible maximum laden

mass’ as specified in point 2.8 of Annex I.
2. General provisions
2.1. Number of seating positions
2.1.1. The requirements regarding the number of seating positions apply to
seats that are designed for use when the vehicle is travelling on the road.
2.1.2. They do not apply to seats that are designed for use when the vehicle is
stationary and which are clearly identified to users either by means of a
pictogram or a sign with an appropriate text.
2.1.3. The following requirements apply for the counting of the seating
positions:
(a) each individual seat shall be counted as one seating position;
(b) in the case of a bench seat, any space having a width of at least
400 mm measured at the seat cushion level shall be counted as one
seating position.
This condition shall not prevent the manufacturer from using the
general provisions referred to in point 1.1;
(c) however, a space as referred to in point (b) shall not be counted as

one seating position where:
(i) the bench seat includes features that prevent the bottom of the
manikin from sitting in a natural way - for example: the
presence of a fixed console box, an unpadded area or an
interior trim interrupting the nominal seating surface;
02007L0046 — EN — 18.01.2018 — 021.001 — 104
▼M12
(ii) the design of the floor pan located immediately in front of a
presumed seating position (for example the presence of a tunnel)
prevents the feet of the manikin from being positioned in a
natural way.
2.1.4. With respect to vehicles covered by Directive 2001/85/EC of the

European Parliament and of the Council of 20 November 2001
relating to special provisions for vehicles used for the carriage of
passengers comprising more than eight seats in addition to the driver’s
seat, and amending Directives 70/156/EEC and 97/27/EC (1), the
dimension referred to in point 2.1.3(b) shall be aligned with the
minimum space required for one person in relation to the various
classes of vehicles.
2.1.5. When seat anchors for a removable seat are present in a vehicle, the
removable seat shall be counted in the determination of the number of
the seating positions.
2.1.6. An area intended for an occupied wheelchair shall be regarded as one

seating position.
2.1.6.1. This provision shall be without prejudice to the requirements of

point 3.6.1 and point 3.7 of Annex VII to Directive 2001/85/EC.
2.2. Maximum mass

2.2.1. In the case of a tractor unit for semi-trailer, the maximum mass to be
considered for classifying the vehicle shall include the maximum mass
of the semi-trailer borne by the fifth wheel coupling.
2.2.2. In the case of a motor vehicle that can tow a centre-axle trailer or a rigid
drawbar trailer, the maximum mass to be considered for classifying the
motor vehicle shall include the maximum mass transferred to the towing
vehicle by the coupling.
2.2.3. In the case of a semi-trailer, a centre-axle trailer and a rigid drawbar

trailer, the maximum mass to be considered for classifying the vehicle
shall correspond to the maximum mass transmitted to the ground by the
wheels of an axle or group of axles when coupled to the towing vehicle.
2.2.4. In the case of a converter dolly, the maximum mass to be considered for
classifying the vehicle shall include the maximum mass of the
semi-trailer borne by the fifth wheel coupling.
2.3. Special equipment

2.3.1. Vehicles fitted primarily with fixed equipment such as machinery or
apparatus shall be regarded as N or O category.
2.4. Units
2.4.1. Unless otherwise stated any unit of measurement and associated symbol
shall conform to the provisions of Council Directive 80/181/EEC (2).
3. Categorisation into vehicle categories

3.1. The manufacturer is responsible for the categorisation of a type of
vehicle into a specific category.
For such purposes, all the relevant criteria described in this Annex shall
be met.
3.2. The approval authority may request from the manufacturer appropriate
additional information with the aim of demonstrating that a vehicle type
needs to be categorised as special purpose vehicle in the special group
(‘SG Code’).
(1) OJ L 42, 13.2.2002, p. 1.

(2) OJ L 39, 15.2.1980 p. 40.
02007L0046 — EN — 18.01.2018 — 021.001 — 105
▼M12
PART A
Criteria for vehicle categorisation
1. Vehicle categories
For the purposes of European and national type-approval, as well as
individual approval, vehicles shall be categorised according to the
following classification:
(It is understood that approval can only be granted for the categories
referred to in points 1.1.1 to 1.1.3, 1.2.1 to 1.2.3 and 1.3.1 to 1.3.4.)
1.1. Category M Motor vehicles designed and constructed primarily

for the carriage of persons and their luggage.
1.1.1. Category M1 Vehicles of category M, comprising not more than

eight seating positions in addition to the driver’s
seating position.
Vehicles belonging to category M1 shall have no

space for standing passengers.
The number of seating positions may be restricted to

one (i.e. the driver’s seating position).
1.1.2. Category M2 Vehicles of category M, comprising more than eight

seating positions in addition to the driver’s seating
position and having a maximum mass not exceeding
5 tonnes.
Vehicles belonging to category M2 may have space

for standing passengers in addition to the seating
positions.
1.1.3. Category M3 Vehicles of category M, comprising more than eight

seating positions in addition to the driver’s seating
position and having a maximum mass exceeding 5
tonnes.
Vehicles belonging to category M3 may have space

for standing passengers.
1.2. Category N Motor vehicles designed and constructed primarily

for the carriage of goods.
1.2.1. Category N1 Vehicles of category N having a maximum mass not

exceeding 3,5 tonnes.
1.2.2. Category N2 Vehicles of category N having a maximum mass

exceeding 3,5 tonnes but not exceeding 12 tonnes.
1.2.3. Category N3 Vehicles of category N having a maximum mass

exceeding 12 tonnes.
1.3. Category O Trailers designed and constructed for the carriage of

goods or of persons as well as for the accom
modation of persons.
1.3.1. Category O1 Vehicles of category O having a maximum mass not

exceeding 0,75 tonnes
1.3.2. Category O2 Vehicles of category O having a maximum mass

exceeding 0,75 tonnes but not exceeding 3,5 tonnes.
02007L0046 — EN — 18.01.2018 — 021.001 — 106
▼M12
1.3.3. Category O3 Vehicles of category O having a maximum mass
exceeding 3,5 tonnes but not exceeding 10 tonnes.
1.3.4 Category O4 Vehicles of category O having a maximum mass

exceeding 10 tonnes.
2. Vehicle subcategories
2.1. Off-road vehicles
‘Off-road vehicle (ORV)’ means a vehicle that belongs either to

category M or N, having specific technical features which permit
its use off the normal roads.
For those categories of vehicles, the letter ‘G’ shall be added as

suffix to the letter and numeral identifying the vehicle category.
The criteria for the subcategorisation of vehicles as ‘ORV’ shall be

specified in Section 4 of Part A of this Annex.
2.2. Special purpose vehicles

2.2.1. ‘Special purpose vehicle (SPV)’ means a vehicle of category M, N or
O having specific technical features in order to perform a function
which requires special arrangements and/or equipment.
For incomplete vehicles that are intended to fall into the SPV
subcategory, the letter ‘S’ shall be added as suffix to the letter and
numeral identifying the vehicle category.
The various types of special purpose vehicles are defined and listed
in Section 5.
2.3. Off road special purpose vehicle

2.3.1. ‘Off road special purpose vehicle (ORV-SPV)’ means a vehicle that
belongs either to category M or N having the specific technical
features referred to in points 2.1 and 2.2.
For those categories of vehicles, the letter ‘G’ shall be added as

suffix to the letter and numeral identifying the vehicle category.
Moreover, for incomplete vehicles that are intended to fall into the
SPV subcategory, the letter ‘S’ shall be added as second suffix.
3. Criteria for the categorisation of vehicles in category N

3.1. The categorisation of a vehicle type in category N shall be based on the
technical features of the vehicle as referred to in points 3.2 to 3.6.
3.2. As a matter of principle, the compartment(s) where all the seating

positions are located shall be completely separated from the loading
area.
3.3. By way of derogation from the requirements of point 3.2, persons

and goods may be transported in the same compartment under the
condition that the loading area is provided with securing devices
designed to protect persons transported against the displacement of
the load during driving, including severe braking and cornering.
3.4. Securing devices - lashing devices - intended for securing the load as
required in point 3.3 as well as partitioning systems, intended for
vehicles up to 7,5 tonnes shall be designed in accordance with the
provisions of Sections 3 and 4 of Standard ISO 27956:2009 ‘Road
vehicles – Securing of cargo in delivery vans – Requirements and
test methods’.
02007L0046 — EN — 18.01.2018 — 021.001 — 107
▼M12
3.4.1. The requirements referred to in point 3.4 may be verified by a
statement of compliance provided by the manufacturer.
3.4.2. As an alternative to the requirements of point 3.4, the manufacturer

may demonstrate to the satisfaction of the approval authority that the
securing devices fitted show an equivalent level of protection as
provided in the referred standard.
3.5. The number of seating positions excluding the driver’s seating

position shall not exceed:
(a) 6 in the case of N1 vehicles;
(b) 8 in the case of N2 or N3 vehicles.
3.6. Vehicles shall show a goods-carrying capacity equal or higher than

the person-carrying capacity expressed in kg.
3.6.1. For such purposes, the following equations shall be satisfied in all
configurations, in particular when all seating positions are occupied:
(a) when N = 0:
P – M ≥ 100 kg
(b) when 0 < N ≤ 2:
P – (M + N × 68) ≥ 150 kg;
(c) when N > 2:
P – (M + N × 68) ≥ N × 68;
where the letters have the following meaning:
‘P’ is the technically permissible maximum laden mass;
‘M’ is the mass in running order;
‘N’ is the number of seating positions excluding the driver’s seating

position.
3.6.2. The mass of equipment that is fitted to the vehicle in order to

accommodate goods (e.g. tank, bodywork, etc.), to handle goods
(e.g. crane, lift, etc.) and to secure goods (e.g. cargo securing
devices) shall be included in M.
The mass of equipment that is not used for the purposes referred to
above (such as a compressor, a winch, an electric power generator,
broadcasting equipment, etc.) shall not be included in M for the
purposes of the application of the above formulae.
3.7. The requirements referred to in points 3.2 to 3.6 shall be met for all
variants and versions within the vehicle type.
3.8. Criteria for the categorisation of vehicles as N1.
3.8.1. A vehicle shall be categorised as N1 when all the applicable criteria

are met.
When one or more of the criteria are not met, the vehicle shall be
categorised as M1.
3.8.2. In addition to the general criteria referred to in points 3.2 to 3.6, the
criteria specified in points 3.8.2.1 to 3.8.2.3.5 shall be met for the
categorisation of vehicles for which the compartment where the
driver is located and the load are within a single unit (i.e.
bodywork ‘BB’).
02007L0046 — EN — 18.01.2018 — 021.001 — 108
▼M12
3.8.2.1. The fact that a wall or a partition, complete or partial, is fitted
between a seat row and the cargo area shall not rule out the obli
gation to meet the required criteria.
3.8.2.2. The criteria shall be as follows:
(a) the loading of the goods shall be possible by a rear door, a

tailgate or a side-door designed and constructed for that
purposes;
(b) in the case of a rear door or a tailgate, the loading aperture shall
meet the following requirements:
(i) in the case the vehicle is fitted with only one row of seats or
with only the driver seat, the minimum height of the loading
aperture shall be at least 600 mm;
(ii) in the case the vehicle is fitted with two or more rows of
seats, the minimum height of the loading aperture shall be at
least 800 mm and the aperture shall show a surface of at
least 12 800 cm2;
(c) The cargo area shall meet the following requirements:
‘cargo area’ means the part of the vehicle located behind the
row(s) of seats or behind the driver seat when the vehicle is
fitted with only one driver seat;
(i) the loading surface of the cargo area shall be generally flat;
(ii) where the vehicle is fitted with only one row of seats or
with one seat, the minimum length of the cargo area shall
be at least 40 % of the wheelbase;
(iii) where the vehicle is fitted with two or more rows of seats,
the minimum length of the cargo area shall be at least 30 %
of the wheelbase.
Where the seats of the last row of seats can be easily

removed from the vehicle without the use of special tools,
the requirements regarding the length of the cargo area shall
be met with all the seats installed in the vehicle;
(iv) the requirements regarding the length of the cargo area shall
be met when the seats of the first row or of the last row, as
the case may be, are upright in their normal position for use
by the vehicle occupants.
3.8.2.3. Specific conditions for measurement

3.8.2.3.1. Definitions
(a) ‘Height of the loading aperture’, means the vertical distance
between two horizontal planes tangent respectively to the
highest point of the lower part of the doorway and the lowest
point of the upper part of the doorway;
(b) ‘surface of the loading aperture’ means the greatest surface of

the orthogonal projection on a vertical plane, perpendicular to
the centreline of the vehicle, of the maximum aperture permitted
when the rear door(s) or tailgate is (are) wide open;
(c) ‘wheelbase’, for the purposes of application of the formulae in

points 3.8.2.2 and 3.8.3.1, means the distance between:
(i) the centreline of the front axle and the centreline of the
second axle in the case of a two axle vehicle; or
02007L0046 — EN — 18.01.2018 — 021.001 — 109
▼M12
(ii) the centreline of the front axle and the centreline of a virtual
axle equally distant from the second and third axle in the
case of a three axle vehicle.
3.8.2.3.2. Seat adjustments

(a) the seats shall be adjusted at their rear outermost positions;
(b) the seat back, if adjustable, shall be adjusted as to accommodate

the three-dimensional H-point machine at a torso angle of 25
degrees;
(c) the seat back, if not adjustable, shall be in the position designed
by the vehicle manufacturer;
(d) When the seat is adjustable in height, it shall be adjusted to its

lowest position.
3.8.2.3.3. Vehicle conditions

(a) the vehicle shall be in loaded conditions corresponding to its
maximum mass;
(b) the vehicle shall be with its wheels straight ahead.
3.8.2.3.4. The requirements of point 3.8.2.3.2 shall not apply when the vehicle
is fitted with a wall or a partition.
3.8.2.3.5. Measurement of the length of the cargo area
(a) when the vehicle is not fitted with a partition or a wall, the
length shall be measured from a vertical plane tangent to the
rear outermost point of the top of the seat back to the rear
internal pane or door or tailgate, in closed position;
(b) when the vehicle is fitted with a partition or a wall, the length
shall be measured from a vertical plane tangent to the rear
outermost point of the partition or the wall to the rear internal
pane or door or tailgate, as the case may be, in closed position;
(c) the requirements concerning the length shall be fulfilled at least

along an horizontal line situated in the longitudinal vertical plane
passing through the centreline of the vehicle, at the level of the
load floor.
3.8.3. In addition to the general criteria referred to in points 3.2 to 3.6, the
criteria specified in points 3.8.3.1 to 3.8.3.4 shall be met for the
categorisation of vehicles for which the compartment where the
driver is located and the load are not within a single unit (i.e.
bodywork ‘BE’).
3.8.3.1. Where the vehicle is fitted with an enclosure type body, the
following shall apply:
(a) the loading of the goods shall be possible by a rear door, a

tailgate or a panel or other means;
(b) the minimum height of the loading aperture shall be at least

800 mm and the aperture shall show a surface of at least
12 800 cm2;
(c) the minimum length of the cargo area shall be at least 40 % of

the wheelbase.
02007L0046 — EN — 18.01.2018 — 021.001 — 110
▼M12
3.8.3.2. Where the vehicle is fitted with an open type cargo area, only the
provisions referred to in points 3.8.3.1(a) and (c) shall apply.
3.8.3.3. For the application of the provisions referred to in point 3.8.3, the
definitions in point 3.8.2 shall apply mutatis mutandis.
3.8.3.4. However, the requirements concerning the length of the cargo area
shall be fulfilled along a horizontal line situated in the longitudinal
plane passing through the centreline of the vehicle at the level of the
load floor.
4. Criteria for the subcategorisation of vehicles as off-road vehicles

4.1. M1 or N1 vehicles shall be subcategorised as off-road vehicles if they
satisfy at the same time the following conditions:
(a) at least one front and at least one rear axle designed to be driven
simultaneously irrespective of whether one powered axle can be
disengaged;
(b) at least one differential locking mechanism or a mechanism

having similar effect is fitted;
(c) they are able to climb at least a 25 % gradient as solo vehicle;
(d) they satisfy five out of the following six requirements:
(i) the approach angle shall be at least 25 degrees;
(ii) the departure angle shall be at least 20 degrees;
(iii) the ramp angle shall be at least 20 degrees;
(iv) the ground clearance under the front axle shall be at least
180 mm;
(v) the ground clearance under the rear axle shall be at least
180 mm;
(vi) the ground clearance between the axles shall be at least

200 mm.
4.2. M2, N2 or M3 vehicles whose maximum mass does not exceed 12

tonnes shall be subcategorised as off-road vehicles if they satisfy the
condition set out in point (a) or both conditions set out in points (b)
and (c):
(a) all their axles are driven simultaneously, irrespective of whether

one or more powered axles can be disengaged;
(b) (i) at least one front and at least one rear axle are designed to
be driven simultaneously irrespective of whether one
powered axle can be disengaged;
(ii) at least one differential locking mechanism or a mechanism

having the same effect is fitted;
(iii) they are able to climb a 25 % gradient as a solo vehicle;

02007L0046 — EN — 18.01.2018 — 021.001 — 111
▼M12
(c) they satisfy at least five out of the following six requirements if
their maximum mass does not exceed 7,5 tonnes and at least
four if their maximum mass exceeds 7,5 tonnes:
250 mm;
(v) the ground clearance between axles shall be at least

300 mm;
(vi) the ground clearance under the rear axle shall be at least
250 mm.
4.3. M3 or N3 vehicles whose maximum mass exceeds 12 tonnes shall be

subcategorised as off-road vehicles if they satisfy the condition set
out in point (a) or both conditions set out in points (b) and (c):
(a) all their axles are driven simultaneously, irrespective of whether

one or more powered axles can be disengaged;
(b) (i) at least half of the axles (or two axles out of the three in the
case of a three axle vehicle and mutatis mutandis in the case
of a five axle vehicle) is designed to be driven simul
taneously, irrespective of whether one powered axle can
be disengaged;
(ii) there is at least one differential locking mechanism or a

mechanism having similar effect;
(iii) they are able to climb a 25 % gradient as solo vehicle;
(c) they satisfy at least four out of the following six requirements:
250 mm;
(v) the ground clearance between axles shall be at least

300 mm;
(vi) the ground clearance under the rear axle shall be at least
250 mm.
4.4. The procedure for checking compliance with the geometrical

provisions referred to in this section shall be set out in Appendix 1.
02007L0046 — EN — 18.01.2018 — 021.001 — 112
▼M12
5. Special purpose vehicles
Name Code Definition
5.1. Motor SA A vehicle of category M with living

caravan accommodation space which contains
the following equipment as a minimum:
(a) seats and table;
(b) sleeping accommodation which may
be converted from the seats;
(c) cooking facilities;
(d) storage facilities.
This equipment shall be rigidly fixed to
the living compartment.
However, the table may be designed to
be easily removable.
5.2. Armoured SB a vehicle intended for the protection of

vehicle conveyed persons or goods with
anti-bullet armour plating.
▼M22
5.3. Ambulance SC a vehicle of category M intended for the

transport of sick or injured persons and
having special equipment for such
purpose.
▼M12
5.4. Hearse SD a vehicle of category M intended for the

transport of deceased persons and having
special equipment for such purpose.
5.5. Wheelchair SH a vehicle of category M1 constructed or

accessible converted specifically so that they
vehicle accommodate one or more persons
seated in their wheelchairs when
travelling on the road.
5.6. Trailer SE a vehicle of category O as defined in

caravan term 3.2.1.3 of Standard ISO 3833:1977.
5.7. Mobile crane SF a vehicle of category N3, not fitted for

the carriage of goods, provided with a
crane whose lifting moment is equal to
or higher than 400 kNm.
5.8. Special group SG a special purpose vehicle which does not

enter in any of the definitions mentioned
in this section.
5.9. Converter SJ a vehicle of category O equipped with

dolly a fifth-wheel coupling to support
a semi-trailer with a view to converting
the latter into a trailer.
5.10. Exceptional SK a vehicle of category O4 intended for the

load transport transport of indivisible loads that is
trailer subject to speed and traffic restrictions
because of its dimensions.
02007L0046 — EN — 18.01.2018 — 021.001 — 113
▼M12
Name Code Definition
Under this term are also included

hydraulic modular trailers irrespective of
the number of modules.
▼M22
5.11. Exceptional SL a road tractor or tractor unit for

load transport semi-trailer of category N3 meeting all
motor vehicle the following conditions:
(a) having more than two axles and at

least half of the axles (two axles
out of three in the case of a three
axle vehicle and mutatis mutandis
in the case of a five axle vehicle)
designed to be driven simultaneously,
irrespective of whether one powered
axle can be disengaged,
(b) which is designed for towing and

pushing exceptional load transport
trailer of category O4,
(c) which has a minimum engine power

of 350 kW, and
(d) which can be equipped with an addi

tional front coupling device for
heavy towable masses
5.12. Multi- SM an off-road vehicle of category N (as

equipment defined in point 2.3) designed and
carrier constructed for pulling, pushing,
carrying and actuating certain
inter-changeable equipment,
(a) with not less than two mounting

areas for this equipment,
(b) with standardised, mechanical,

hydraulic and/or electrical interfaces
(e.g. Power take off) for powering
and actuating the above mentioned
equipment and
(c) which fulfills the definition of ISO

3833-1977, section 3.1.4 (special
vehicle).
If the vehicle is equipped with an

auxiliary load platform, its maximum
length shall not exceed:
(a) 1,4 times of the front or rear track

width of the vehicle, whichever is
the larger in the case of two axle
vehicles, or
(b) 2,0 times of the front or rear track

width of the vehicle, whichever is
the larger in the case of vehicles
having more than two axles
02007L0046 — EN — 18.01.2018 — 021.001 — 114
▼M12
6. Remarks
6.1. Type-approval shall not be granted:
(a) to converter dolly as defined in Section 5 of Part A of this

Annex;
(b) to rigid drawbar trailers as defined in Section 4 of Part C of this

Annex;
(c) to trailers in which persons may be carried when travelling on

the road.
6.2. Paragraph 6.1 is without prejudice to the provisions of Article 23 on

national small series type-approval.
PART B
Criteria for vehicle types, variants and versions
1. Category M1
1.1. Vehicle type
1.1.1. A ‘vehicle type’ shall consist of vehicles which have all of the following
features in common:
(a) the manufacturer’s company name.
A change in the legal form of ownership of the company does not

require that a new approval has to be granted;
(b) the design and assembly of the essential parts of the body structure
in the case of a self-supporting body.
The same shall apply mutatis mutandis to vehicles the bodywork of

which is bolted on or welded to a separate frame;
(c) in the case of multi-stage built vehicles, the manufacturer and the
type of the previous stage vehicle.
1.1.2. By way of derogation from the requirements of point 1.1.1(b), when the
manufacturer uses the floor portion of the body structure as well as the
essential constituent elements forming the front part of the body structure
located directly in front of the windscreen bay, in the construction of
different kinds of bodywork (for example a saloon and a coupe), those
vehicles may be considered as belonging to the same type. Evidence
thereof shall be provided by the manufacturer.
1.1.3. A type shall consist of at least one variant and one version.
1.2. Variant
1.2.1. A ‘variant’ within a vehicle type shall group the vehicles which have all
of the following construction features in common:
(a) the number of lateral doors or the type of bodywork as defined in

Section 1 of Part C when the manufacturer uses the criterion of
point 1.1.2;
(b) the power plant with regard to the following construction features:
(i) the type of energy supply (internal combustion engine, electric

motor or other);
(ii) the working principle (positive ignition, compression ignition or

other);
(iii) the number and arrangement of cylinders in the case of internal

combustion engine (L4, V6 or other);
02007L0046 — EN — 18.01.2018 — 021.001 — 115
▼M12
(c) the number of axles;
(d) the number, and interconnection of powered axles;
(e) the number of steered axles;
(f) the stage of completion (e.g. complete/incomplete).
1.3. Version
1.3.1. A ‘version’ within a variant shall group the vehicles which have all the
following features in common:
(a) the technically permissible maximum laden mass;
(b) the engine capacity in the case of internal combustion engine;
(c) the maximum engine power output or the maximum continuous rated
power (electric motor);
(d) the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(e) the maximum number of seating positions;
(f) drive-by sound level;
(g) exhaust emission level (for example Euro 5, Euro 6 or other);
(h) combined or weighted, combined CO2 emissions;
(i) electric energy consumption (weighted, combined);
(j) combined or weighted, combined fuel consumption;
(k) the existence of a unique set of innovative technologies, as specified

in Article 12 of Regulation (EC) No 443/2009 (1).
▼M27
As an alternative to the criteria (h), (i) and (j), the vehicles grouped into
a version shall have all tests performed for the calculation of their CO2
emissions, electric energy consumption and fuel consumptions according
to the provisions of sub-Annex 6 to Annex XXI of Regulation (EU)
2017/1151 in common.
▼M12
2. Categories M2 and M3
2.1. Vehicle type
features in common:

(b) the category;
(c) the following aspects of construction and design:
(i) the design and construction of the essential constituent elements

forming the chassis;
(ii) the design and construction of the essential constituent elements

forming the body structure in the case of a self-supporting body;
(d) the number of decks (single or double);
(1) OJ L 140, 5.6.2009, p. 1.

02007L0046 — EN — 18.01.2018 — 021.001 — 116
▼M12
(e) the number of sections (rigid/articulated);
(f) the number of axles;
(g) the mode of energy supply (on-board or off-board);
(h) in the case of multi-stage built vehicles, the manufacturer and the
2.2. Variant
(a) the type of bodywork as defined in Section 2 of Part C;
(b) the class or combination of classes of vehicles as defined in

point 2.1.1 of Annex I to Directive 2001/85/EC (only in the case
of complete and completed vehicles);
(c) the stage of completion (e.g. complete/incomplete/completed);
(d) the power plant with regard to the following construction features:

motor or other);

other);

combustion engine (L6, V8 or other).
2.3. Version
(b) the ability of the vehicle to tow a trailer or not;
(c) the engine capacity in the case of internal combustion engine;
(d) the maximum engine power output or the maximum continuous rated
(e) the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(g) exhaust emission level (for example Euro IV, Euro V or other).
3. Category N1
3.1. Vehicle type
features in common:

(b) the design and assembly of the essential parts of the body structure
in the case of a self-supporting body;
02007L0046 — EN — 18.01.2018 — 021.001 — 117
▼M12
(c) the design and the construction of the essential constituent elements
forming the chassis in the case of a non self-supporting body;
(d) in the case of multi-stage built vehicles, the manufacturer and the
3.1.2. By way of derogation from the requirements of point 3.1.1(b), when the
manufacturer uses the floor portion of the body structure as well the
essential constituent elements forming the front part of the body
structure located directly in front of the windscreen bay, in the
construction of different kinds of bodywork (for example a van and
a chassis-cab, different wheelbases and different roof heights), those
vehicles may be considered as belonging to the same type. Evidence
thereof shall be provided by the manufacturer.
3.2. Variant
(a) the number of lateral doors or the type of bodywork as defined in

Section 3 of Part C (for complete and completed vehicles) when the
manufacturer uses the criterion of point 3.1.2;
(b) the stage of completion (e.g. complete/incomplete/completed);
(c) the power plant with regard to the following construction features:

motor or other);

other);

(d) the number of axles;
(e) the number and interconnection of powered axles;
(f) the number of steered axles.
3.3. Version
(b) the engine capacity in the case of internal combustion engine;
(c) the maximum engine power output or maximum continuous rated

(d) the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(e) the maximum number of seating positions;

02007L0046 — EN — 18.01.2018 — 021.001 — 118
▼M12
(g) exhaust emission level (for example Euro 5, Euro 6 or other);
(h) combined or weighted, combined CO2 emissions;
(i) electric energy consumption (weighted, combined);
(j) combined or weighted, combined fuel consumption ;
▼M27
(k) the existence of a unique set of innovative technologies, as specified
in Article 12 of Regulation (EU) No 510/2011 (1).
As an alternative to the criteria (h), (i) and (j), the vehicles grouped into
a version shall have all tests performed for the calculation of their CO2
emissions, electric energy consumption and fuel consumptions according
to the provisions of sub-Annex 6 to Annex XXI of Regulation (EU)
2017/1151 in common.
▼M12
4. Categories N2 and N3
4.1. Vehicle type
essential features in common:

(b) the category;
(c) the design and construction of the chassis that are common to a
single line of product;
(d) the number of axles;
(e) in the case of multi-stage built vehicles, the manufacturer and the
4.2. Variant
(a) the body structural concept or type of bodywork as referred to in

Section 3 of Part C and in Appendix 2 (only for complete and
completed vehicles);
(c) the power plant with regard to the following construction features:

motor or other);

other);

(d) the number and interconnection of powered axles;
(e) the number of steered axles.
(1) OJ L 145 31.5.2011, p. 1.

02007L0046 — EN — 18.01.2018 — 021.001 — 119
▼M12
4.3. Version
(b) the ability or not to tow a trailer as follows:
(i) an unbraked trailer;
(ii) a trailer with an inertia (or overrun) braking system as defined

in point 2.12 of UNECE Regulation No 13;
(iii) a trailer with a continuous or semi-continuous braking system as

defined in points 2.9 and 2.10 of UNECE Regulation No 13;
(iv) a trailer of category O4 that results in a maximum mass of the

combination not exceeding 44 tonnes;
(v) a trailer of category O4 that results in a maximum mass of the

combination exceeding 44 tonnes;
(c) the engine capacity;
(d) the maximum engine power output;
(e) the nature of the fuel (petrol, gas oil, LPG, bi-fuel or other);
(g) exhaust emission level (for example Euro IV, Euro V or other).
5. Categories O1 and O2
5.1. Vehicle type
features in common:

(b) the category;
(c) the concept as defined in section 4 of Part C;
(d) the following aspects of construction and design:


forming the body structure in the case of a self-supporting body;
(e) the number of axles;
(f) in the case of multi-stage built vehicles, the manufacturer and the
5.2. Variant
(a) the kind of bodywork as referred to in Appendix 2 (for complete and

(c) the type of braking system (e.g. unbraked/inertia/power).

02007L0046 — EN — 18.01.2018 — 021.001 — 120
▼M12
5.3. Version
(b) the concept of the suspension (air, steel or rubber suspension, torsion
bar or other);
(c) the concept of the drawbar (triangle, tube or other).
6. Categories O3 and O4
6.1. Vehicle type
features in common:

(b) the category;
(c) the concept of the trailer with relation to the definitions in section 4
of Part C;
(d) the following aspects of construction and design:


forming the body structure in the case of trailers with a self-
supporting body;
(e) the number of axles;
(f) in the case of multi-stage built vehicles, the manufacturer and the
6.2. Variants
of the following construction and design features in common:
(a) the kind of bodywork as referred to in Appendix 2 (for complete and

(c) the concept of the suspensions (steel, air or hydraulic suspension);
(d) the following technical features:
(i) the capability or not for the chassis to be extendible;
(ii) the deck height (normal, low loader, semi-low loader etc.).
02007L0046 — EN — 18.01.2018 — 021.001 — 121
▼M12
6.3. Versions
(b) the subdivisions or combination of subdivisions referred to in points

3.2 and 3.3 of Annex I to Directive 96/53/EC into which the axle
spacing between two consecutive axles forming a group belongs;
(c) the definition of the axles in the following respects;
(i) lift axles (number and position);
(ii) loadable axles (number and position);
(iii) steered axle (number and position).
7. Common requirements for all vehicle categories

7.1. When a vehicle falls into several categories because of its maximum
mass or the number of seating positions or both, the manufacturer may
select to use the criteria of one or the other vehicle category for the
definition of the variants and the versions.
7.1.1. Examples:
(a) a vehicle ‘A’ may be type-approved as N1 (3,5 tonnes) and N2 (4,2

tonnes) in relation to its maximum mass. In such a case, the
parameters mentioned in category N1 may be used also for the
vehicle that falls into category N2 (or vice-versa);
(b) A vehicle ‘B’ may be type-approved as M1 and M2 in relation to the

number of seating positions (7 + 1 or 10 + 1), the parameters
mentioned in category M1 may be used also for the vehicle that
falls into category M2 (or vice-versa).
7.2. A vehicle of category N may be type-approved against the provisions

required for category M1 or M2, as the case may be, when it is intended
to be converted into a vehicle of that category during the next step of
a multi-stage type-approval procedure.
7.2.1. This option shall only be permitted for incomplete vehicles.
Such vehicles shall be identified by a specific variant code given by the

manufacturer of the base vehicle.
7.3. Type-, variant- and version designations
7.3.1. The manufacturer shall allocate an alphanumeric code to each vehicle

type, variant and version, made up of Roman letters and/or Arabic
numerals.
The use of brackets and hyphens is permitted provided they do not

replace a letter or a numeral.
02007L0046 — EN — 18.01.2018 — 021.001 — 122
▼M12
7.3.2. The whole code shall be designated: Type-Variant-Version or ‘TVV’.
7.3.3. The TVV shall clearly and unequivocally identify a unique combination
of technical features in relation to the criteria defined in Part B of this
Annex.
7.3.4. The same manufacturer may use the same code in order to define a
vehicle type when the latter falls in two or more categories.
7.3.5. The same manufacturer shall not use the same code in order to define a
vehicle type for more than one type-approval within the same vehicle
category.
7.4. Number of characters for the TVV

7.4.1. The number of characters shall not exceed:
(a) 15 for the code of the vehicle type;
(b) 25 for the code of one variant;
(c) 35 for the code of one version.
7.4.2. The complete alphanumeric ‘TVV’ shall not contain more than 75
characters.
7.4.3. When the TVV is used as a whole, a space shall be left between the
type, the variant and the version.
Example of such TVV: 159AF[…space]0054[…space]977K(BE).
PART C
Definitions of types of bodywork
0. General
0.1. The type of bodywork referred to in Section 9 of Annex I and Part 1 of
Annex III as well as the code for bodywork referred to in Item 38 of
Annex IX shall be indicated by means of codes.
The list of codes shall apply primarily to complete and completed

vehicles.
0.2. As regards vehicles of categories M, the type of bodywork shall consist

of two letters as specified in Sections 1 and 2.
0.3. As regards vehicles of categories N and O, the type of bodywork shall

consist of two letters as referred to in Sections 3 and 4.
0.4. Where necessary (especially for the types of bodywork referred to

respectively in points 3.1 and 3.6 and in points 4.1 to 4.4), they shall
be supplemented by two digits.
0.4.1. The list of digits shall be laid down in Appendix 2 to this Annex.
0.5. For special purpose vehicles, the type of bodywork to be used shall be
linked to the category of the vehicle.
02007L0046 — EN — 18.01.2018 — 021.001 — 123
▼M12
1. Vehicles belonging to category M1
Ref. Code Name Definition
1.1. AA Saloon a vehicle defined in term 3.1.1.1 of Standard ISO 3833:1977,

fitted with at least four side windows.
1.2. AB Hatchback a saloon as defined in 1.1 with a hatch at the rear end of the
vehicle.
1.3. AC Station wagon a vehicle defined in term 3.1.1.4 of Standard ISO 3833:1977.
1.4. AD Coupé a vehicle defined in term 3.1.1.5 of Standard ISO 3833:1977.
1.5. AE Convertible a vehicle defined in terms No 3.1.1.6 of Standard ISO 3833:1977.
However a convertible may have no door.
1.6. AF Multi-purpose a vehicle other than AG and those mentioned in AA to AE

vehicle intended for carrying persons and their luggage or occasionally
goods, in a single compartment.
1.7. AG Truck station a vehicle defined in terms No 3.1.1.4.1 of Standard ISO

wagon 3833:1977.
However, the luggage compartment must be completely separated

from the passenger compartment.
In addition, the reference point of the driver’s seating position

needs not to be at least at 750 mm above the surface supporting
the vehicle.
2. Vehicles belonging to category M2 or M3
2.1. CA Single-deck a vehicle where the spaces provided for persons are arranged in a
vehicle single level or in a way that they do not constitute two super
imposed levels;
2.2. CB Double-deck a vehicle defined in point 2.1.6 of Annex I to Directive 2001/85/EC;

vehicle
2.3. CC Single-deck a vehicle defined in point 2.1.3 of Annex I to Directive 2001/85/EC

articulated with a single deck;
vehicle
2.4. CD Double-deck a vehicle defined in point 2.1.3.1 of Annex I to Directive 2001/85/EC;

articulated
vehicle
2.5. CE Low-floor a vehicle defined in point 2.1.4 of Annex I to Directive 2001/85/EC

single-deck with a single deck;
vehicle
2.6. CF Low-floor a vehicle defined in point 2.1.4 of Annex I to Directive 2001/85/EC

double-deck with a double deck;
vehicle
2.7. CG Articulated a vehicle that combines the technical features of entries 2.3 and
low-floor 2.5;
single-deck
vehicle
2.8. CH Articulated a vehicle that combines the technical features of entries 2.4 and
low-floor 2.6;
double-deck
vehicle
02007L0046 — EN — 18.01.2018 — 021.001 — 124
▼M12
2.9. CI Open top single a vehicle with partial roof or without roof;
deck vehicle
2.10. CJ Open top double a vehicle without roof over all or part of its upper deck;
deck vehicle
2.11. CX Bus chassis an incomplete vehicle with just chassis rails or tube assembly,
power train, axles, which is intended to be completed with
bodywork, customised to the needs of the transport operator.
3. Motor vehicles of category N1, N2 or N3
3.1. BA Lorry a vehicle which is designed and constructed exclusively or

principally for conveying goods.
It may also tow a trailer.
3.2. BB Van a lorry with the compartment where the driver is located and
cargo area within a single unit;
3.3. BC Tractor unit for a towing vehicle which is designed and constructed exclusively or
semi-trailer principally to tow semi-trailers;
3.4. BD Road tractor a towing vehicle which is designed and constructed exclusively to
tow trailers other than semi-trailers;
3.5. BE Pick-up truck a vehicle of a maximum mass not exceeding 3 500 kg in which
the seating positions and the cargo area are not located in a single
compartment;
3.6. BX Chassis-cab or an incomplete vehicle with just a cabin (complete or partial),

chassis-cowl chassis rails, power train, axles, which is intended to be
completed with bodywork, customised to the needs of the
transport operator.
4. Vehicles of category O
4.1. DA Semi-trailer a trailer which is designed and constructed to be coupled to a

tractor unit or to a converter dolly and to impose a substantial
vertical load on the towing vehicle or on the converter dolly.
The coupling to be used for a vehicle combination shall consist of

a king pin and a fifth wheel.
4.2. DB Drawbar trailer a trailer having at least two axles, of which at least one is a
steered axle:
(a) equipped with a towing device which can move vertically (in
relation to the trailer) and
(b) that transmits less than 100 daN as a static vertical load to the
towing vehicle.
4.3. DC Centre-axle a trailer where the axle(s) is (are) positioned close to the centre of
trailer gravity of the vehicle (when uniformly loaded) so that only a
small static vertical load, not exceeding 10 % of that corre
sponding to the maximum mass of the trailer or a load of 1 000
daN (whichever is the lesser) is transmitted to the towing vehicle.
02007L0046 — EN — 18.01.2018 — 021.001 — 125
▼M12
4.4. DE Rigid drawbar a trailer with one axle or one group of axles fitted with a drawbar
trailer which transmits a static load not exceeding 4 000 daN to the
towing vehicle due to its construction and which does not meet
the definition of a centre-axle trailer.
The coupling to be used for a vehicle combination shall not

consist of a king pin and a fifth wheel.
02007L0046 — EN — 18.01.2018 — 021.001 — 126
▼M12
Appendix 1
Procedure for checking whether a vehicle can be categorised as off-road

vehicle
0. General
0.1. For the purposes of classification of a vehicle as off-road vehicle, the
procedure described in this Appendix shall apply.
1. Test conditions for geometric measurements

1.1. Vehicles belonging to category M1 or N1 shall be in unloaded conditions
with a manikin of the 50th percentile male installed on the driver’s seat
and fitted with coolant fluid, lubricants, fuel, tools, spare-wheel (if fitted
as OEM equipment).
The manikin may be replaced by a similar device having the same mass.
1.2. Vehicles other than those referred to in point 1.1 shall be loaded to their
technically permissible maximum laden mass.
The distribution of the mass on the axles shall be the one that represents
the worst case with respect to compliance with the respective criteria.
1.3. A vehicle representative of the type shall be submitted to the technical

service in the conditions specified in point 1.1 or 1.2. The vehicle shall be
in a stationary position with its wheels set straight ahead.
The ground on which measurements are made shall be as flat and hori
zontal (maximum of inclination 0,5 %) as possible.
2. Measurement of approach, departure and ramp angles

2.1. The approach angle shall be measured in accordance with Item 6.10 of
Standard ISO 612:1978.
2.2. The departure angle shall be measured in accordance with Item 6.11 of
2.3. The ramp angle shall be measured in accordance with Item 6.9 of
2.4. When measuring the departure angle rear underrun protection devices
which are adjustable in height may be set in the upper position.
2.5. The prescription in point 2.4 shall not be construed as an obligation for
the base vehicle to be fitted with a rear underrun protection as original
equipment. However, the base vehicle manufacturer shall inform the next
stage manufacturer that the vehicle has to comply with the requirements
on departure angle when fitted with a rear underrun protection.
3. Measurement of ground clearance

3.1. Ground clearance between the axles
3.1.1. ‘Ground clearance between the axles’ means the shortest distance between
the ground plane and the lowest fixed point of the vehicle.
02007L0046 — EN — 18.01.2018 — 021.001 — 127
▼M12
For the application of the definition, the distance between the last axle of a
front group of axle and the first axle of a rear group of axle shall be
considered.
3.1.2. No rigid part of the vehicle may project into the shaded area shown on the
figure.
3.2. Ground clearance beneath one axle
3.2.1. ‘Ground clearance beneath one axle’ means the distance beneath the
highest point of the arc of a circle passing through the centre of the
tyre footprint of the wheels on one axle (the inner wheels in the case
of twin tyres) and touching the lowest fixed point of the vehicle between
the wheels.
3.2.2. Where appropriate, the measurement of ground clearance shall be

conducted on each of the several axles of a group of axles.
4. Gradeability
4.1. ‘Gradeability’ means the ability of a vehicle to negotiate a gradient.
4.2. To the effect of checking the gradeability of an incomplete and a complete
vehicle of category M2, M3, N2 and N3, a test shall be performed.
4.3. The test shall be conducted by the technical service on a vehicle repre
sentative of the type to be tested.
4.4. At the request of the manufacturer and under the conditions specified in
Annex XVI, the gradeability of a vehicle type may be demonstrated by
virtual testing.
5. Test conditions and pass-fail criterion
5.1. Until 31 October 2014, the conditions set out in section 7.5 of Annex I to
Directive 97/27/EC shall apply.
As from 1 November 2014, test conditions adopted under Regulation (EC)
No 661/2009 of the European Parliament and of the Council (1) in
accordance with Article 14 of that Regulation shall apply.
5.2. The vehicle shall climb the gradient at a steady speed without any wheel
slipping, longitudinally or laterally.
(1) OJ L 200, 31.7.2009, p. 1.

02007L0046 — EN — 18.01.2018 — 021.001 — 128
▼M12
Appendix 2
Digits used to supplement the codes to be used for various kinds of

bodywork
01 Flat bed;
02 Drop-side;
03 Box body;
04 Conditioned body with insulated walls and equipment to maintain the
interior temperature;
05 Conditioned body with insulated walls but without equipment to maintain the
interior temperature;
06 Curtain-sided;
07 Swap body (interchangeable superstructure);
08 Container carrier;
09 Vehicles fitted with hook lift;
10 Tipper;
11 Tank;
12 Tank intended for transport of dangerous goods;
13 Livestock carrier;
14 Vehicle transporter;
15 Concrete mixer;
16 Concrete pump vehicle;
17 Timber;
18 Refuse collection vehicle;
19 Street sweeper, cleansing and drain clearing;
20 Compressor;
21 Boat carrier;
22 Glider carrier;
23 Vehicles for retail or display purposes;
24 Recovery vehicle;
25 Ladder vehicle;
26 Crane lorry (other than a mobile crane as defined in Section 5 of Part A of
Annex II);
27 Aerial work platform vehicle;
28 Digger derrick vehicle;
29 Low floor trailer;
30 Glazing transporter;
31 Fire engine;
99 Bodywork that is not included in the present list.
02007L0046 — EN — 18.01.2018 — 021.001 — 129
▼M1
ANNEX III
INFORMATION DOCUMENT FOR THE PURPOSE OF EC

TYPE-APPROVAL OF VEHICLES
(For explanatory notes, please refer to last page of Annex I)
PART I
The following information shall be supplied in triplicate and include a list of
contents. Any drawings shall be supplied in appropriate scale and in sufficient
detail on size A4, or on a folder of A4 format. Photographs, if any, shall show
sufficient detail.
A. Categories M and N
0. GENERAL
0.1. Make (trade name of manufacturer): … . . . . . . . . . . . . . . . . . . . . . . .
0.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2.1. Commercial name(s) (if available): … . . . . . . . . . . . . . . . . . . . . . . . . .
▼M24
0.2.2. For multi-stage approved vehicles, type-approval information of
the base/previous stage vehicle (list the information for each
stage. This can be done with a matrix):
Type: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Variant(s): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Version(s): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type-approval number, including extension number: … . . . . . . .
▼M1
0.3. Means of identification of type, if marked on the vehicle (b): …
0.3.1. Location of that marking: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.4. Category of vehicle (c): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vehicle is intended to transport: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
0.5. Company name and address of manufacturer: … . . . . . . . . . . . . . .
▼M24
0.5.1. For multi-stage approved vehicles, company name and address
of the manufacturer of the base/previous stage(s) vehicle: … . .
▼M1
0.8. Name(s) and address(es) of assembly plant(s): … . . . . . . . . . . . . .

… ............................................................
1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE

VEHICLE
1.1. Photographs and/or drawings of a representative vehicle: … . . .
1.3. Number of axles and wheels: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1. Number and position of axles with twin wheels: … . . . . . . . . . . .
1.3.2. Number and position of steered axles: … . . . . . . . . . . . . . . . . . . . . .
1.3.3. Powered axles (number, position, interconnection): … . . . . . . . . .
1.4. Chassis (if any) (overall drawing): … . . . . . . . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 130
▼M1
1.6. Position and arrangement of the engine: … . . . . . . . . . . . . . . . . . . .
1.8. Hand of drive: left/right (1)
1.8.1. Vehicle is equipped to be driven in right/left (1) hand traffic
▼M15
other trailers and, if the trailer is a semi-, drawbar-, centre-axle-
or rigid drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

controlled-temperature carriage of goods: … . . . . . . . . . . . . . . . . . . .
2. MASSES AND DIMENSIONS (f)(g)(7)

▼M1
2.1.1. Two-axle vehicles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.2.1. Axle spacing between consecutive axles going from the foremost
to the rearmost axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2.2. Total axle spacing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1. Track of each steered axle (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2. Track of all other axles (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.1.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.1. Maximum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.2. Minimum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.1. Maximum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.2. Minimum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
height, indicate normal running position): … . . . . . . . . . . . . . . . . . .

2.4.2.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.1.1. Length of the loading area: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
controlled-temperature transport of goods): … . . . . . . . . . . . . . . . . .
▼M15
2.5. Minimum mass on the steering axle(s) for incomplete
vehicles: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

(a) minimum and maximum for each variant: … . . . . . . . . . . . . . .
(b) mass of each version (a matrix must be provided): … . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 131
▼M15
a semi-trailer a rigid drawbar trailer or a centre-axle trailer, the
mass on the coupling:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.2. Mass of the optional equipment (as defined in point (5) of
Article 2 of Regulation (EU) No 1230/2012: … . . . . . . . . . . . . . . .
▼M1
manufacturer, in the case of an incomplete vehicle: … . . . . . . . .
manufacturer (i) (3): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
point (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9. Technically permissible maximum mass on each axle: … . . .

▼M15
2.10. Technically permissible mass on each group of axles: … . . .
2.11. Technically permissible maximum towable mass of the
towing vehicle
in case of:
▼M1
2.11.1. Drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.2. Semi-trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.3. Centre-axle trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
2.11.4. Rigid drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11.5. Technically permissible maximum laden mass of the combi
nation (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
2.11.6. Maximum mass of unbraked trailer: …. . . . . . . . . . . . . . . . . . . . . . . .
▼M15
point:
2.12.1. of a towing vehicle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.12.2. of a semi-trailer, a centre-axle trailer or a rigid drawbar trailer:
… ............................................................
(optional)
2.16.1. Registration/in service maximum permissible laden mass: … . .
2.16.2. Registration/in service maximum permissible mass on each axle
and, in the case of a semi-trailer or centre-axle trailer, intended
load on the coupling point stated by the manufacturer if lower
than the technically permissible maximum mass on the coupling
point: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
group of axles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.16.4. Registration/in service maximum permissible towable mass: …
2.16.5. Registration/in service maximum permissible mass of the combi
nation: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M24
2.17. Vehicle submitted to multi-stage type-approval (only in the case
of incomplete or completed vehicles of category N1 within the
scope of Regulation (EC) No 715/2007: yes/no (1)
02007L0046 — EN — 18.01.2018 — 021.001 — 132
▼M24
2.17.1. Mass of the base vehicle in running order: . . . . . . . . . . . . . . . kg.
2.17.2. Default added mass (DAM), calculated in accordance with Section 5

of Annex XII to Regulation (EC) No 692/2008: . . . . . . . . . . . . . kg
▼M27
3. PROPULSION ENERGY CONVERTER (k)
3.1. Manufacturer of the propulsion energy converter(s): . . . . . .
3.1.1. Manufacturer's code (as marked on the propulsion energy

converter or other means of identification): . . . . . . . . . . . . . . . . . . .
▼M1
3.1.2. Approval number (if appropriate) including fuel identification
marking: …
3.2. Internal combustion engine

▼M21
3.2.1.1. Working principle: positive ignition/compression ignition/dual-
fuel (1)
Cycle four stroke/two stroke/rotary (1)
3.2.1.1.1. Type of dual-fuel engine: Type 1A/Type 1B/Type 2A/Type

2B/Type 3B (1)(x1)
3.2.1.1.2. Gas Energy Ratio over the hot part of the WHTC
test-cycle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . %
▼M1
3.2.1.2. Number and arrangement of cylinders: … . . . . . . . . . . . . . . . . . . . . .
3.2.1.3. Engine capacity (m): …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cm3
3.2.1.6. Normal engine idling speed (2): …… . . . . . . . . . . . . . . . . . . . min-1
▼M21
3.2.1.6.2. Idle on diesel: yes/no (1)(x1)
▼M27
3.2.1.8. Rated engine power (n): . . . . . . kW at . . . . . min–1 (manu
facturer's declared value)
▼M11
3.2.1.11. (Euro VI only) Manufacturer references of the Documentation
package required by Articles 5, 7 and 9 of Regulation (EU)
No 582/2011 enabling the approval authority to evaluate the
emission control strategies and the systems on-board the
engine to ensure the correct operation of NOx control measures
▼M1
3.2.2.1. Light-duty vehicles: Diesel/Petrol/LPG/NG or Biomethane/
Ethanol (E 85)/Biodiesel/Hydrogen (1) (6)
▼M21
3.2.2.2. Heavy duty vehicles Diesel/Petrol/LPG/NG-H/NG-L/NG-
HL/Ethanol (ED95)/Ethanol (E85)/LNG/LNG20 (1)(6)
▼M11
3.2.2.2.1. (Euro VI only) Fuels compatible with use by the engine declared
by the manufacturer in accordance with Section 1.1.3 of Annex I
to Regulation (EU) No 582/2011 (as applicable)
▼M1
3.2.2.4. Vehicle fuel type: Mono fuel, Bi fuel, Flex fuel (1)
3.2.2.5. Maximum amount of biofuel acceptable in fuel (manufacturer's

declared value): …… . . . . . . . . . . . . . . . . . . . . . . . . . . % by volume
02007L0046 — EN — 18.01.2018 — 021.001 — 133
▼M1
3.2.3. Fuel tank(s)
3.2.3.1. Service fuel tank(s)
3.2.3.1.1. Number and capacity of each tank: … . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3.2. Reserve fuel tank(s)
3.2.3.2.1. Number and capacity of each tank: … . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4. Fuel feed

3.2.4.1. By carburettor(s): yes/no (1)
▼M21
3.2.4.2. By fuel injection (compression ignition or dual-fuel only): yes/no (1)
▼M1
3.2.4.2.2. Working principle: direct injection/pre-chamber/swirl cham-
ber (1)
3.2.4.3. By fuel injection (positive ignition only): yes/no (1)
3.2.7. Cooling system: liquid/air (1)
3.2.8. Intake system

3.2.8.1. Pressure charger: yes/no (1)
3.2.8.2. Intercooler: yes/no (1)
▼M11
3.2.8.3.3. (Euro VI only) Actual Intake system depression at rated engine
speed and at 100 % load on the vehicle: kPa
▼M1
3.2.9. Exhaust system
▼M11
3.2.9.2.1. (Euro VI only) Description and/or drawing of the elements of the
exhaust system that are not part of the engine system
3.2.9.3.1. (Euro VI only) Actual exhaust back pressure at rated engine

speed and at 100 % load on the vehicle (compression-ignition
engines only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kPa
▼M1
3.2.9.4. Type, marking of exhaust silencer(s): …
Where relevant for exterior noise, reducing measures in the

engine compartment and on the engine: … . . . . . . . . . . . . . . . . . . . .
3.2.9.5. Location of the exhaust outlet: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M11
3.2.9.7.1. (Euro VI only) Acceptable Exhaust system volume: … . . . dm3
▼M1
3.2.12. Measures taken against air pollution
▼M11
3.2.12.1.1. (Euro VI only) Device for recycling crankcase gases: yes/no (2)
If yes, description and drawings:
If no, compliance with Annex V to Regulation (EU)

No 582/2011 required
▼M27
3.2.12.2. Pollution control devices (if not covered by another heading)
3.2.12.2.1. Catalytic converter
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 134
▼M27
__________
3.2.12.2.2.1. Oxygen sensor: yes/no (1)
▼M1
3.2.12.2.3. Air injection: yes/no (1)
3.2.12.2.4. Exhaust gas recirculation: yes/no (1)
▼M27
3.2.12.2.5. Evaporative emissions control system (petrol and ethanol engines
only): yes/no (1)
▼M1
3.2.12.2.6. Particulate trap: yes/no (1)
▼M11
3.2.12.2.6.9. Other systems: yes/no (1)
3.2.12.2.6.9.1. Description and operation
▼M1
3.2.12.2.7. On-board-diagnostic (OBD) system: yes/no (1)
▼M11
3.2.12.2.7.0.1. (Euro VI only) Number of OBD engine families within the
engine family
3.2.12.2.7.0.2. (Euro VI only) List of the OBD engine families (when

applicable)
engine / the engine member belongs to:
3.2.12.2.7.0.4. (Euro VI only) Manufacturer references of the

OBD-Documentation required by Article 5(4)(c) and Article 9(4)
of Regulation (EU) No 582/2011 and specified in Annex X to
that Regulation for the purpose of approving the OBD system
3.2.12.2.7.0.5. (Euro VI only) When appropriate, manufacturer reference of the

Documentation for installing in a vehicle an OBD equipped
engine system
3.2.12.2.7.0.6. (Euro VI only) When appropriate, manufacturer reference of the

documentation package related to the installation on the vehicle
of the OBD system of an approved engine
▼M21
__________
3.2.12.2.7.6.5. (Euro VI only) OBD Communication protocol standard: (8)
▼M11
3.2.12.2.7.7. (Euro VI only) Manufacturer reference of the OBD related
information required by of Article 5(4)(d) and Article 9(4) of
Regulation (EU) No 582/2011 for the purpose of complying with
the provisions on access to vehicle OBD and vehicle Repair and
Maintenance Information, or
02007L0046 — EN — 18.01.2018 — 021.001 — 135
▼M11
3.2.12.2.7.7.1. As an alternative to a manufacturer reference provided in Section
3.2.12.2.7.7 reference of the attachment to the information
document set out in Appendix 4 of Annex III to
Regulation (EU) No 582/2011 that contains the following
table, once completed according to the given example:
Component — Fault code — Monitoring strategy — Fault

detection criteria — MI activation criteria — Secondary
parameters — Preconditioning — Demonstration test
Catalyst — P0420 — Oxygen sensor 1 and 2 signals —

Difference between sensor 1 and sensor 2 signals — 3rd cycle
— Engine speed, engine load, A/F mode, catalyst temperature —
Two Type 1 cycles — Type 1
▼M21
3.2.12.2.7.8. (EURO VI only) OBD components on-board the vehicle
3.2.12.2.7.8.1. List of OBD components on-board the vehicle
3.2.12.2.7.8.2. Written description and/or drawing of the MI (10)
3.2.12.2.7.8.3. Written description and/or drawing of the OBD off-board

communication interface (10)
▼M27
3.2.12.2.8. Other system
▼M11
3.2.12.2.8.1. (Euro VI only) Systems to ensure the correct operation of NOx
control measures
▼M21
3.2.12.2.8.2. Driver inducement system
3.2.12.2.8.2.1. (Euro VI only) Engine with permanent deactivation of the driver

inducement, for use by the rescue services or in vehicles
specified in point (b) of Article 2(3) of this Directive: yes/no (1)
▼M11
3.2.12.2.8.3. (Euro VI only) Number of OBD engine families within the
of NOx control measures
3.2.12.2.8.4. (Euro VI only) List of the OBD engine families (when

applicable)
3.2.12.2.8.5. (Euro VI only) Number of the OBD engine family the parent
engine / the engine member belongs to
3.2.12.2.8.6. (Euro VI only) Lowest concentration of the active ingredient

present in the reagent that does not activate the warning
system (CDmin): (% vol.)
3.2.12.2.8.7. (Euro VI only) When appropriate, manufacturer reference of the

Documentation for installing in a vehicle the systems to ensure
the correct operation of NOx control measures
3.2.12.2.8.8. Components on-board the vehicle of the systems ensuring the

correct operation of NOx control measures
3.2.12.2.8.8.1. Activation of the creep mode:
‘disable after restart’ / ‘disable after fuelling’ / ‘disable after

parking’ (7)
3.2.12.2.8.8.2. When appropriate, manufacturer reference of the documentation

package related to the installation on the vehicle of the system
ensuring the correct operation of NOx control measures of an
approved engine
02007L0046 — EN — 18.01.2018 — 021.001 — 136
▼M11
3.2.12.2.8.8.3. Written description and/or drawing of the warning signal (6)
▼M1
3.2.12.2.9. Torque limiter: yes/no (1)
▼M27
3.2.12.2.10. Periodically regenerating system: (provide the information below
for each separate unit)
3.2.12.2.10.1. Method or system of regeneration, description and/or drawing: .
3.2.12.2.11.1. Type and concentration of reagent needed: . . . . . . . . . . . . . . . . . . .
▼M1
3.2.13.1. Location of the absorption coefficient symbol (compression
ignition engines only): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.15. LPG fuelling system: yes/no (1)
3.2.16. NG fuelling system: yes/no (1)
▼M11
3.2.17.8.1.0.1. (Euro VI only) Self adaptive feature? Yes/No (1)
3.2.17.8.1.0.2. (Euro VI only) Calibration for a specific gas composition

NG-H/NG-L/NG-HL (1)
Transformation for a specific gas composition NG-Ht/NG-

Lt/NG-HLt (1)
▼M27
3.3. Electric machine
▼M1
3.3.1. Type (winding, excitation): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1.1. Maximum hourly output: …… . . . . . . . . . . . . . . . . . . . . . . . . . . . kW
▼M20
3.3.1.1.1. Maximum net power (n) … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kW
3.3.1.1.2. Maximum 30 minutes power (n) … . . . . . . . . . . . . . . . . . . . . . . kW
▼M1
3.3.1.2. Operating voltage: …… . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
▼M27
3.3.2. REESS
▼M1
3.3.2.4. Position: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M27
3.4. Combinations of propulsion energy converters
▼M1
3.4.1. Hybrid electric vehicle: yes/no (1)
3.4.2. Category of hybrid electric vehicle: off-vehicle charging/not

off-vehicle charging: (1)
▼M27
__________
▼M30
3.5.7. CO2 emissions and fuel consumption certification (for
heavy-duty vehicles, as specified in Article 6 of Commission
Regulation (EU) 2017/2400)
3.5.7.1. Simulation tool licence number:

02007L0046 — EN — 18.01.2018 — 021.001 — 137
▼M1
3.6.5. Lubricant temperature
Minimum: …… K
Maximum: …… K
4. TRANSMISSION (p)
4.2. Type (mechanical, hydraulic, electric, etc.): … . . . . . . . . . . . . . . . .
4.5. Gearbox
4.5.1. Type (manual/automatic/CVT (continuously variable trans
mission)) (1)
▼M27
4.6. Gear ratios
Internal gearbox ratios Final drive ratio(s) (ratio of

Gear (ratios of engine to gearbox gearbox output shaft to Total gear ratios
output shaft revolutions) driven wheel revolutions)
Maximum for CVT
Minimum for CVT

Reverse
▼M1
4.7. Maximum vehicle design speed (in km/h) (q)
4.9. Tachograph: yes/no (1)
4.9.1 Approval mark: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M13
4.11. Gear shift indicator (GSI)
4.11.1. Acoustic indication available yes/no (1). If yes, description of
sound and sound level at the driver’s ear in dB(A). (Acoustic
indication always switchable on/off)
4.11.2. Information according to point 4.6 of Annex I to

Regulation (EU) No 65/2012 (determined at type-approval)
▼M1
5. AXLES
5.1. Description of each axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4. Position of retractable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5. Position of loadable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. SUSPENSION
6.2. Type and design of the suspension of each axle or wheel: … .
02007L0046 — EN — 18.01.2018 — 021.001 — 138
▼M1
6.2.3. Air-suspension for driving axle(s): yes/no (1)
6.2.3.1. Suspension of driving axle equivalent to air-suspension:

yes/no (1)

yes/no (1)
▼M27
▼M1
(a) for tyres indicate size designation, load-capacity index, speed
category symbol, rolling resistance in accordance with ISO
28580 (where applicable) (r);
(b) for wheels indicate rim size(s) and off-set(s)
6.6.1.1. Axles
6.6.1.1.1. Axle 1: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.1.1.2. Axle 2: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
etc.
6.6.1.2. Spare wheel, if any: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2. Upper and lower limits of rolling radii

6.6.2.1. Axle 1: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2.2. Axle 2: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
etc.
7. STEERING
applicable): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2. Linkage to wheels (including other than mechanical means;

specify for front ans rear, if applicable): … . . . . . . . . . . . . . . . . . . .
7.2.3. Method of assistance, if any: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8. BRAKES
8.5. Anti-lock braking system: yes/no/optional (1)
8.9. Brief description of the braking system according to item 1.6 of

the Addendum to Appendix 1 of Annex IX to Directive
71/320/EEC: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.11. Particulars of the type(s) of endurance braking system(s): … . .
9. BODYWORK
▼M27
9.1. Type of bodywork using the codes defined in Part C of Annex II
of Directive 2007/46/EC: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
9.3. Occupant doors, latches and hinges
02007L0046 — EN — 18.01.2018 — 021.001 — 139
▼M1
9.3.1. Door configuration and number of doors: … . . . . . . . . . . . . . . . . . .
9.9. Devices for indirect vision

9.9.1. Rear-view mirrors, stating, for each rear-view mirror:
9.9.1.1. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.2. Type-approval mark: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.3. Variant: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.1.6. Optional equipment which may affect the rearward field of

vision: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.9.2. Devices for indirect vision other than mirrors: … . . . . . . . . . . . . .
9.9.2.1. Type and description of the device: … . . . . . . . . . . . . . . . . . . . . . . . .
9.10. Interior arrangement

9.10.3. Seats
9.10.3.1. Number of seating positions (s): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.1.1. Location and arrangement: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.10.3.2. Seat(s) designated for use only when the vehicle is stationary: …
9.10.4.1. Type(s) of head restraints: integrated/detachable/separate (1)
9.10.4.2. Type-approval number(s), if available: …
9.10.8 Gas used as refrigerant in the air-conditioning system: … . . . . .
9.10.8.1. The air-conditioning system is designed to contain fluorinated

greenhouse gases with a global warming potential higher than
150: yes/no (1)
9.12.2. Nature and position of supplementary restraint systems (indicate

yes/no/optional): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front airbag Side airbag Belt pre-loading device

8
>
> L
>
>
<
>
>
>
>
:
R
8
>
> L
>
>
<
>
>
>
>
:
R

number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

inscriptions (completed example with dimensions): … . . . . . . . . .
02007L0046 — EN — 18.01.2018 — 021.001 — 140
▼M1
number (completed example with dimensions): … . . . . . . . . . . . . .

be explained: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
requirements of section 5.4 of ISO Standard 3779-1983, these
characters shall be indicated: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.22. Front under-run protection

9.23. Pedestrian protection

relevant reference lines and the constituent materials of the
frontal part of the vehicle (interior and exterior), including
detail of any active protection system installed
▼M2
9.24. Frontal protection systems
9.24.1. General arrangement (drawings or photographs) indicating the

position and attachment of the frontal protection systems:
9.24.3. Complete details of fittings required and full instructions,

including torque requirements, for fitting:
▼M1
11.1. Class and type of the coupling device(s) fitted or to be fitted: …
11.3. Instructions for attachment of the coupling type to the vehicle

and photographs or drawings of the fixing points at the vehicle
as stated by the manufacturer; additional information, if the use
of the coupling type is restricted to certain variants or versions of
the vehicle type: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.4. Information of the fitting of special towing brackets or mounting

plates: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11.5. Type-approval number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12. MISCELLANEOUS
12.7.1. Vehicle equipped with a 24 GHz short-range radar equipment:
yes/no (1)
13. SPECIAL PROVISIONS FOR BUSES AND COACHES

13.1. Class of vehicle: Class I/Class II/Class III/Class A/Class B (1)
02007L0046 — EN — 18.01.2018 — 021.001 — 141
▼M1
13.1.2. Chassis types where the type-approved bodywork can be
installed (manufacturer(s), and vehicle(s) types): …. . . . . . . . . . . .
13.3. Number of passengers (seated and standing)
13.3.1. Total (N): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3.2. Upper deck (Na) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.3.3. Lower deck (Nb) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4. Number of passengers (seated)
13.4.1. Total (A): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.2. Upper deck (Aa) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.3. Lower deck (Ab) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13.4.4. Number of wheelchair positions for category M2 and M3

vehicles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16. ACCESS TO VEHICLE REPAIR AND MAINTENANCE

INFORMATION
16.1. Address of principal website for access to vehicle repair and
maintenance information: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. Category O
0. GENERAL
0.1. Make (trade name of manufacturer): … . . . . . . . . . . . . . . . . . . . . . . .
0.2. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2.1. Commercial name(s) (if available): … . . . . . . . . . . . . . . . . . . . . . . . . .
0.3. Means of identification of type, if marked on the vehicle (b): …
0.3.1. Location of that marking: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.4. Category of vehicle (c): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

vehicle is intended to transport: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
0.5. Company name and address of manufacturer: … . . . . . . . . . . . . . .
▼M1
0.8. Name(s) and address(es) of assembly plant(s): … . . . . . . . . . . . . .

… ............................................................
1. GENERAL CONSTRUCTION CHARACTERISTICS OF THE

VEHICLE
1.1. Photographs and/or drawings of a representative vehicle: … . . .
1.3. Number of axles and wheels: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1. Number and position of axles with twin wheels: … . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 142
▼M1
1.3.2. Number and position of steered axles: … . . . . . . . . . . . . . . . . . . . . .
1.4. Chassis (if any) (overall drawing): … . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
other trailers and, if the trailer is a semi-, drawbar-, centre-axle-
or rigid drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

controlled-temperature carriage of goods: … . . . . . . . . . . . . . . . . . . .
2. MASSES AND DIMENSIONS (f) (g) (7)
▼M1
2.1.1. Two-axle vehicles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.2.1. Axle spacing between consecutive axles going from the foremost
to the rearmost axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1.2.2. Total axle spacing: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1. Track of each steered axle (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2. Track of all other axles (g4): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.1.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.1. Maximum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.2. Minimum permissible length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.1.3. In the case of trailers, maximum permissible drawbar length (g6):

… ............................................................
2.4.1.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.1. Maximum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1.2.2. Minimum permissible width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.2.1. Length (g5): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.1.1. Length of the loading area: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2.1.2. In the case of trailers, maximum permissible drawbar length (g6):

… ............................................................
2.4.2.2. Width (g7): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
controlled-temperature transport of goods): … . . . . . . . . . . . . . . . . .
2.4.2.3. Height (in running order) (g8) (for suspension adjustable for
02007L0046 — EN — 18.01.2018 — 021.001 — 143
▼M15
a semi-trailer a rigid drawbar trailer or a centre-axle trailer, the
mass on the coupling: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.2. Mass of the optional equipment (as defined in point (5) of

Article 2 of Regulation (EU) No 1230/2012: … . . . . . . . . . . . . . . .
▼M1
manufacturer, in the case of an incomplete vehicle: … . . . . . . . .

manufacturer (i) (3): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.1. Distribution of this mass among the axles, and in the case of
point (3): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9. Technically permissible maximum mass on each axle: … . . .
▼M15
2.10. Technically permissible mass on each group of axles: … . . .

point:
2.12.2. Of a semi-trailer, a centre-axle trailer or a rigid drawbar trailer:

… ............................................................

(optional)
2.16.1. Registration/in service maximum permissible laden mass: … . .
2.16.2. Registration/in service maximum permissible mass on each axle

and, in the case of a semi-trailer or centre-axle trailer, intended
load on the coupling point stated by the manufacturer if lower
than the technically permissible maximum mass on the coupling
point: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

group of axles: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
2.16.4. Intended registration/in service maximum permissible towable
mass (several entries possible for each technical configura-
tion (5)): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M15
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 144
▼M1
4. TRANSMISSION
4.7. Maximum vehicle design speed (in km/h) (q)
5. AXLES
5.1. Description of each axle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2. Make: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3. Type: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4. Position of retractable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.5. Position of loadable axle(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. SUSPENSION
6.2. Type and design of the suspension of each axle or wheel: … .

yes/no (1)

(a) for tyres indicate size designation, load-capacity index, speed
category symbol, rolling resistance in accordance with ISO
28580 (where applicable) (r);
(b) for wheels indicate rim size(s) and off-set(s)
6.6.1.1. Axles
6.6.1.1.1. Axle 1: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.1.1.2. Axle 2: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
etc.
6.6.1.2. Spare wheel, if any: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2. Upper and lower limit of rolling radii

6.6.2.1. Axle 1: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6.2.2. Axle 2: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
etc.
7. STEERING
applicable): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2. Linkage to the wheels (including other than mechanical means;

specify for front and rear, if applicable): … . . . . . . . . . . . . . . . . . . .
7.2.3. Method of assistance, if any: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 145
▼M1
8. BRAKES
8.5. Antilock braking system: yes/no/optional (1)
8.9. Brief description of the braking system, according to item 1.6 of

the addendum to Appendix 1 of Annex IX to Directive
71/320/EEC: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9. BODYWORK
9.1. Type of bodywork using the codes defined in Part C of
Annex II: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

inscriptions (completed example with dimensions): … . . . . . . . . .

number (completed example with dimensions): … . . . . . . . . . . . . .

be explained: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
requirements of section 5.4 of ISO Standard 3779-1983 these
characters shall be indicated: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1. Class and type of the coupling device(s) fitted or to be fitted: …
11.5. Type-approval number(s): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PART II
Matrix showing the combinations of the entries listed in Part I within the
versions and variants of the vehicle type
Item No All Version 1 Version 2 Version 3 Version n
Notes:
(a) A separate matrix shall be compiled for each variant within the type.
(b) Entries for which there are no restrictions on their combination within a
variant shall be listed in the column headed ‘all’.
(c) The above information may be presented in an alternative layout or merged

with the information supplied in Part I.
02007L0046 — EN — 18.01.2018 — 021.001 — 146
▼M1
(d) Each variant and each version shall be identified by an alphanumerical code
consisting of a combination of letters and numbers, which shall also be
indicated in the certificate of conformity (Annex IX) of the vehicle
concerned.
(e) Variant(s) which fall(s) under Annex XI shall be identified by a specific
alphanumerical code.
PART III
Type-approval numbers
Supply the information required by the following table in respect of the
applicable subjects for this vehicle in Annex IV or Annex XI. (All relevant
approvals for each subject shall be included. However, information in respect
of components need not be given here so long as such information is included in
the approval certificate relating to the installation prescriptions).
Member State or
Type-approval number Contracting Party (*)
Extension Variant(s)/
Subject or test report issuing the
date version(s)
number (***) type-approval (**) or
test report (***)
(*) Contracting Parties to the Revised 1958 Agreement.

(**) To be indicated if not obtainable from the type-approval number.
(***) To be indicated when the manufacturer applies the provisions of Article 9(6). In such
a case, the applied regulatory act shall be specified in the second column.
Signed: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position in company: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Date: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
▼M1
ANNEX IV
▼M12
REQUIREMENTS FOR THE PURPOSE OF EC TYPE-APPROVAL OF VEHICLES
▼M14
PART I
Regulatory acts for EC type-approval of vehicles produced in unlimited series
Applicability
Item Subject Regulatory act
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
1 Permissible sound level Directive 70/157/EEC X X X X X X
▼M23
1A Sound level Regulation (EU) No 540/2014 X X X X X X
▼M14
►M22 2A ◄ Emissions (Euro 5 and 6) light duty vehicles/access Regulation (EC) No 715/2007 X (1) X (1) X (1) X (1)
to information
02007L0046 — EN — 18.01.2018 — 021.001 — 147

▼M6
▼C1
__________
▼M14
3A Prevention of fire risks (liquid fuel tanks) Regulation (EC) No 661/2009 X X X X X X X X X X
UNECE Regulation No 34
3B Rear underrun protective devices (RUPDs) and Regulation (EC) No 661/2009 X X X X X X X X X X

their installation; rear underrun protection (RUP) UNECE Regulation No 58
▼M6
▼C1
__________
▼M14
4A Space for mounting and fixing rear registration Regulation (EC) No 661/2009 X X X X X X X X X X
plates Regulation (EU) No 1003/2010
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
5A Steering equipment Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
__________
▼M26
6A Vehicle access and manoeuvrability (steps, running Regulation (EC) No 661/2009 X X X X
boards and handholds) Regulation (EU) No 130/2012
▼M14
02007L0046 — EN — 18.01.2018 — 021.001 — 148

6B Door latches and door retention components Regulation (EC) No 661/2009 X X
▼M6
▼C1
__________
▼M14
7A Audible warning devices and signals Regulation (EC) No 661/2009 X X X X X X
▼M6
▼C1
__________
▼M14
8A Devices for indirect vision and their installation Regulation (EC) No 661/2009 X X X X X X
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
9A Braking of vehicles and trailers Regulation (EC) No 661/2009 X (3) X (3) X (3) X (3) X (3) X (3) X (3) X (3) X (3)
9B Braking of passenger cars Regulation (EC) No 661/2009 X (4) X (4)

UNECE Regulation No 13-H
▼M6
▼C1
__________
▼M14
10A Electromagnetic compatibility Regulation (EC) No 661/2009 X X X X X X X X X X
02007L0046 — EN — 18.01.2018 — 021.001 — 149

▼M6
▼C1
__________
▼M14
12A Interior fittings Regulation (EC) No 661/2009 X
▼M6
▼C1
__________
▼M14
13A Protection of motor vehicles against unauthorised Regulation (EC) No 661/2009 X (4A) X (4A) X (4A) X (4A)
use UNECE Regulation No 18
13B Protection of motor vehicles against unauthorised Regulation (EC) No 661/2009 X X

use UNECE Regulation No 116
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
14A Protection of the driver against the steering Regulation (EC) No 661/2009 X X
mechanism in the event of impact UNECE Regulation No 12
▼M6
▼C1
__________
▼M14
15A Seats, their anchorages and any head restraints Regulation (EC) No 661/2009 X X (4B) X (4B) X X X
15B Seats of large passenger vehicles Regulation (EC) No 661/2009 X X

▼M6
02007L0046 — EN — 18.01.2018 — 021.001 — 150

▼C1
__________
▼M14
16A External projections Regulation (EC) No 661/2009 X
▼M6
▼C1
__________
▼M26
17A Vehicle access and manoeuvrability (reverse gear) Regulation (EC) No 661/2009 X X X X X X
Regulation (EU) No 130/2012
▼M14
17B Speedometer equipment including its installation Regulation (EC) No 661/2009 X X X X X X
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
18A Manufacturer’s statutory plate and vehicle identifi Regulation (EC) No 661/2009 X X X X X X X X X X
cation number Regulation (EU) No 19/2011
▼M6
▼C1
__________
▼M14
19A Safety-belt anchorages, Isofix anchorages systems Regulation (EC) No 661/2009 X X X X X X
and Isofix top tether anchorages UNECE Regulation No 14
▼M6
02007L0046 — EN — 18.01.2018 — 021.001 — 151

▼C1
__________
▼M14
20A Installation of lighting and light-signalling devices Regulation (EC) No 661/2009 X X X X X X X X X X
on vehicles UNECE Regulation No 48
▼M6
▼C1
__________
▼M14
21A Retro-reflecting devices for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X X X X X
and their trailers UNECE Regulation No 3
▼M6
▼C1
__________
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
22A Front and rear position lamps, stop-lamps and Regulation (EC) No 661/2009 X X X X X X X X X X
end-outline marker lamps for motor vehicles and UNECE Regulation No 7
their trailers
22B Daytime running lamps for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X
22C Side-marker lamps for motor vehicles and their Regulation (EC) No 661/2009 X X X X X X X X X X
trailers UNECE Regulation No 91
▼M6
▼C1
__________
▼M14
23A Direction indicators for power-driven vehicles and Regulation (EC) No 661/2009 X X X X X X X X X X
their trailers UNECE Regulation No 6
02007L0046 — EN — 18.01.2018 — 021.001 — 152

▼M6
▼C1
__________
▼M14
24A Illumination of rear-registration plates of Regulation (EC) No 661/2009 X X X X X X X X X X

power-driven vehicles and their trailers UNECE Regulation No 4
▼M6
▼C1
__________
▼M14
25A Power-driven vehicle’s sealed-beam Regulation (EC) No 661/2009 X X X X X X

headlamps (SB) emitting an European asym UNECE Regulation No 31
metrical passing beam or a driving beam or both
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
25B Filament lamps for use in approved lamp units of Regulation (EC) No 661/2009 X X X X X X X X X X
25C Motor vehicle headlamps equipped with Regulation (EC) No 661/2009 X X X X X X

gas-discharge light sources UNECE Regulation No 98
25D Gas-discharge light sources for use in approved Regulation (EC) No 661/2009 X X X X X X
gas-discharge lamp units of power-driven vehicles UNECE Regulation No 99
25E Motor vehicle headlamps emitting an asymmetrical Regulation (EC) No 661/2009 X X X X X X

passing beam or a driving beam or both and UNECE Regulation No 112
equipped with filament lamps and/or LED modules
25F Adaptive front-lighting systems (AFS) for motor Regulation (EC) No 661/2009 X X X X X X
vehicles UNECE Regulation No 123
▼M6
▼C1
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 153

▼M14
26A Power-driven vehicle front fog lamps Regulation (EC) No 661/2009 X X X X X X

▼M6
▼C1
__________
▼M14
27A Towing device Regulation (EC) No 661/2009 X X X X X X

▼M6
▼C1
__________
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
28A Rear fog lamps for power-driven vehicles and their Regulation (EC) No 661/2009 X X X X X X X X X X
trailers UNECE Regulation No 38
▼M6
▼C1
__________
▼M14
29A Reversing lights for power-driven vehicles and Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
__________
▼M14
30A Parking lamps for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X
02007L0046 — EN — 18.01.2018 — 021.001 — 154

▼M6
▼C1
__________
▼M14
31A Safety-belts, restraint systems, child restraint Regulation (EC) No 661/2009 X X X X X X

systems and Isofix child restraint systems UNECE Regulation No 16
▼M6
▼C1
__________
▼M14
32A Forward field of vision Regulation (EC) No 661/2009 X

▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
33A Location and identification of hand controls, Regulation (EC) No 661/2009 X X X X X X
tell-tales and indicators UNECE Regulation No 121
▼M6
▼C1
__________
▼M14
34A Windscreen defrosting and demisting systems Regulation (EC) No 661/2009 X (5) (5) (5) (5) (5)
▼M6
02007L0046 — EN — 18.01.2018 — 021.001 — 155

▼C1
__________
▼M14
35A Windscreen wiper and washer systems Regulation (EC) No 661/2009 X (6) (6) (6) (6) (6)
▼M6
▼C1
__________
▼M14
36A Heating systems Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
__________
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
37A Wheel guards Regulation (EC) No 661/2009 X

▼M6
▼C1
__________
▼M22
38A Head restraints (headrests), whether or not incor Regulation (EC) No 661/2009 X
porated in vehicle seats UNECE Regulation No 25
▼M5
__________
▼M30
41A Emissions (Euro VI) heavy duty vehicles/access to Regulation (EC) No 595/2009 X (9) X (9) X X (9) X (9) X
information Regulation (EU) No 582/2011
41B CO2 simulation tool licence (heavy-duty vehicles) Regulation (EC) 595/2009 X (16) X
02007L0046 — EN — 18.01.2018 — 021.001 — 156

Regulation (EU) 2017/2400
▼M6
▼C1
__________
▼M14
42A Lateral protection of goods vehicles Regulation (EC) No 661/2009 X X X X

▼M6
▼C1
__________
▼M14
43A Spray suppression systems Regulation (EC) No 661/2009 X X X X X X X

▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
44A Masses and dimensions Regulation (EC) No 661/2009 X

▼M6
▼C1
__________
▼M14
02007L0046 — EN — 18.01.2018 — 021.001 — 157

45A Safety glazing materials and their installation on Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
__________
▼M14
46A Installation of tyres Regulation (EC) No 661/2009 X X X X X X X X X X

46B Pneumatic tyres for motor vehicles and their Regulation (EC) No 661/2009 X X X X
trailers (Class C1) UNECE Regulation No 30
46C Pneumatic tyres for commercial vehicles and their Regulation (EC) No 661/2009 X X X X X X X
trailers (Classes C2 and C3) UNECE Regulation No 54
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
46D Tyre rolling sound emissions, adhesion on wet Regulation (EC) No 661/2009 X X X X X X X X X X
surfaces and rolling resistance (Classes C1, C2 UNECE Regulation No 117
and C3)
46E Temporary-use spare unit, run-flat tyres/system and Regulation (EC) No 661/2009 X (9A) X (9A)
tyre pressure monitoring system UNECE Regulation No 64
▼M6
▼C1
__________
▼M14
47A Speed limitation of vehicles Regulation (EC) No 661/2009 X X X X

▼M6
02007L0046 — EN — 18.01.2018 — 021.001 — 158

▼C1
__________
▼M14
48A Masses and dimensions Regulation (EC) No 661/2009 X X X X X X X X X

▼M6
▼C1
__________
▼M14
49A Commercial vehicles with regard to their external Regulation (EC) No 661/2009 X X X
projections forward of the cab’s rear panel UNECE Regulation No 61
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
▼M6
▼C1
__________
▼M14
50A Mechanical coupling components of combinations Regulation (EC) No 661/2009 X (10) X (10) X (10) X (10) X (10) X (10) X X X X
of vehicles UNECE Regulation No 55
50B Close-coupling device (CCD); fitting of an Regulation (EC) No 661/2009 X (10) X (10) X (10) X (10)
approved type of CCD UNECE Regulation No 102
▼M6
▼C1
__________
▼M14
02007L0046 — EN — 18.01.2018 — 021.001 — 159

51A Burning behaviour of materials used in the interior Regulation (EC) No 661/2009 X
construction of certain categories of motor vehicles UNECE Regulation No 118
▼M6
▼C1
__________
▼M14
52A M2 and M3 vehicles Regulation (EC) No 661/2009 X X

52B Strength of the superstructure of large passenger Regulation (EC) No 661/2009 X X

▼M6
▼C1
__________
▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
53A Protection of occupants in the event of a frontal Regulation (EC) No 661/2009 X (11)
collision UNECE Regulation No 94
▼M6
▼C1
__________
▼M14
54A Protection of occupants in the event of lateral Regulation (EC) No 661/2009 X (12) X (12)
▼M6
▼C1
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 160

▼M14
56A Vehicles for the carriage of dangerous goods Regulation (EC) No 661/2009 X (13) X (13) X (13) X (13) X (13) X (13) X (13)
▼M6
▼C1
__________
▼M14
57A Front underrun protective devices (FUPDs) and Regulation (EC) No 661/2009 X X
their installation; front underrun protection (FUP) UNECE Regulation No 93
58 Pedestrian protection Regulation (EC) No 78/2009 X X
59 Recyclability Directive 2005/64/EC X X -

▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
60 (empty)
61 Air-conditioning systems Directive 2006/40/EC X X (14)
62 Hydrogen system Regulation (EC) No 79/2009 X X X X X X
63 General Safety Regulation (EC) No 661/2009 X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15)
64 Gear shift indicators Regulation (EC) No 661/2009 X

65 Advanced emergency braking system Regulation (EC) No 661/2009 X X X X
02007L0046 — EN — 18.01.2018 — 021.001 — 161

66 Lane departure warning system Regulation (EC) No 661/2009 X X X X

67 Specific components for liquefied petroleum Regulation (EC) No 661/2009 X X X X X X

gases (LPG) and their installation on motor UNECE Regulation No 67
vehicles
68 Vehicle alarm systems (VAS) Regulation (EC) No 661/2009 X X

69 Electric safety Regulation (EC) No 661/2009 X X X X X X

▼M14
Applicability
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
70 Specific components for CNG and their installation Regulation (EC) No 661/2009 X X X X X X
on motor vehicles UNECE Regulation No 110
▼M26
71 Cab strength Regulation (EC) No 661/2009 X X X
▼M14
Explanatory notes:
X Regulatory act applicable.
Note: The series of amendments of the UNECE Regulations which apply on a compulsory basis are listed in Annex IV to Regulation (EC) No 661/2009. Series of amendments adopted subsequently are accepted as an
alternative.
(1) For vehicles with a reference mass not exceeding 2 610 kg. At the manufacturer’s request, may apply to vehicles with a reference mass not exceeding 2 840 kg.
(2) In case of vehicles equipped with a LPG or CNG installation, a vehicle type-approval in accordance with UNECE Regulation No 67 or UNECE Regulation No 110 is required.
(3) The fitting of an electronic stability control (‘ESC’) system is required in accordance with Article 12 of Regulation (EC) No 661/2009. Therefore, the requirements set out in Annex 21 to UNECE Regulation 13 shall be
complied with for the purposes of EC type-approval of new types of vehicles as well as for the registration, sale and entry into service of new vehicles. The implementation dates set out in Article 13 of Regulation (EC)
No 661/2009 shall apply instead of the dates set out in UNECE Regulation No 13.
(4) The fitting of an ESC system is required in accordance with Article 12 of Regulation (EC) No 661/2009. Therefore, the requirements set out in Part A of Annex 9 to UNECE Regulation No 13-H shall be complied with for
the purposes of EC type-approval of new types of vehicles as well as for the registration, sale and entry into service of new vehicles. The implementation dates set out in Article 13 Regulation (EC) No 661/2009 shall apply
instead of the dates set out in UNECE Regulation No 13-H.
(4A) If fitted, the protective device shall fulfil the requirements of UNECE Regulation No 18.
02007L0046 — EN — 18.01.2018 — 021.001 — 162

4B
( ) This Regulation applies to seats not falling within the scope of UNECE Regulation No 80.
(5) Vehicles of this category shall be fitted with a suitable windscreen defrosting and demisting device.
(6) Vehicles of this category shall be fitted with a suitable windscreen washing and wiping devices.
►M20
__________ ◄
(8) For vehicles with a reference mass exceeding 2 610 kg and which did not benefit from the possibility offered in note (1).
(9) For vehicles with a reference mass exceeding 2 610 kg which are not type-approved (at the manufacturer’s request and provided their reference mass does not exceed 2 840 kg) under Regulation (EC) No 715/2007.
For other options, see Article 2 of Regulation (EC) No 595/2009.
(9A) Applies only where such vehicles are fitted with equipment covered by UNECE Regulation No 64. Tyre pressure monitoring system for M1 vehicles applies on a compulsory basis in accordance with Article 9(2) of
Regulation (EC) No 661/2009.
(10) Applies only to vehicles equipped with coupling(s).
( ) Applies to vehicles with a technically permissible maximum laden mass not exceeding 2,5 tonnes.
11
(12) Only applicable to vehicles where the ‘Seating Reference Point (‘R’ point)’ of the lowest seat is not more than 700 mm above the ground level.
(13) Applies only when the manufacturer applies for type-approval of vehicles intended for the transport of dangerous goods.
(14) Applies only for vehicles of category N1, class I as described in the first table in point 5.3.1.4 of Annex I to Directive 70/220/EEC.
►M26 (15) Compliance with Regulation (EC) No 661/2009 is mandatory, however, type-approval under this single item is not provided for as the item covers the combination of individual items 3A, 3B, 4A, 5A, 6A, 6B, 7A,
8A, 9A, 9B, 10A, 12A, 13A, 13B, 14A, 15A, 15B, 16A, 17A, 17B, 18A, 19A, 20A, 21A, 22A, 22B, 22C, 23A, 24A, 25A, 25B, 25C, 25D, 25E, 25F, 26A, 27A, 28A, 29A, 30A, 31A, 32A, 33A, 34A, 35A, 36A, 37A, 38A,
42A, 43A, 44A, 45A, 46A, 46B, 46C, 46D, 46E, 47A, 48A, 49A, 50A, 50B, 51A, 52A, 52B, 53A, 54A, 56A, 57A and 64 to 71. ◄
►M30 (16) For vehicles with a technically permissible maximum laden mass from 7 500 kg. ◄
02007L0046 — EN — 18.01.2018 — 021.001 — 163
▼M14
Appendix 1
Regulatory acts for EC type-approval of vehicles produced in small series

pursuant to Article 22
1. This Appendix applies to new EC type-approvals of small series granted from

1 November 2012, except for item 54A which applies from 1 November
2014.
2. EC type-approvals of small series granted before 1 November 2012 shall
cease to be valid on 31 October 2016. National authorities shall consider
certificates of conformity for vehicles to be no longer valid for the purposes
of Article 26(1) of this Directive, unless the type-approvals concerned have
been updated to the requirements of this Appendix.
Table 1
M1 vehicles (1)
Item Subject Regulatory act Specific issues Applicability and specific requirements
1 Permissible sound Directive 70/ A

level 157/EEC
▼M23
1A Sound level Regulation A

(EU) No 540/
2014
▼M20
2 Emissions (Euro 5 Regulation A

and 6) light duty (EC) No 715/
vehicles/access to 2007 (a) On-board diagnostic The vehicle shall be fitted with an
information (OBD) OBD system that fulfils the
requirements of Article 4(1) and (2)
of Regulation (EC) No 692/ 2008
(The OBD system shall be designed
to record at least the malfunction of
the engine management system).
The OBD-interface shall be able to
communicate with commonly
available diagnostic tools.
(b) In service confor N/A

mity
(c) Access to informa It is sufficient that the manufacturer

tion provide access to repair and main
tenance information in a readily
accessible and prompt manner.
(d) Power measurement (When the vehicle manufacturer uses

an engine from another manufacturer)
Bench test data from the engine manu
facturer are accepted provided that the
engine management system is
identical (i.e. having at least the
same ECU).
Power output test may be performed
on a chassis dynamometer. It shall
be taken into account of the power
loss in the transmission.
(1) The explanatory notes relating to Part I of Annex IV apply also to Table 1.
02007L0046 — EN — 18.01.2018 — 021.001 — 164
▼M14
3A Prevention of fire Regulation (a) Liquid fuel tanks B

risks (liquid fuel (EC) No 661/
tanks) 2009
UNECE Regu (b) Installation in vehicle B
lation No 34
▼M22
3B Rear underrun Regulation B

protective devices (EC) No 661/
(RUPDs) and their 2009
installation; rear
UNECE Regu
underrun
lation No 58
protection (RUP)
▼M14
4A Space for mounting Regulation B

and fixing rear (EC) No 661/
registration plates 2009
Regulation
(EU) No 1003/
2010
5A Steering equipment Regulation C

(EC) No 661/
2009
UNECE Regu (a) Mechanical systems The provisions of paragraph 5 of
lation No 79 UNECE Regulation No 79 shall
apply.
All tests prescribed in paragraph 6.2
of UNECE Regulation No 79 shall
be performed and the requirements of
paragraph 6.1 of UNECE Regulation
No 79 shall apply.
(b) Complex electronic All the requirements of Annex 6 of

vehicle control UNECE Regulation No 79 shall
system apply.
Compliance with these requirements
may only be checked by an
appointed technical service.
6A Door latches and Regulation C

door retention (EC) No 661/
components 2009
UNECE Regu (a) General All the requirements shall apply.
lation No 11 requirements
(Paragraph 5 of
UNECE Regulation
No 11)
(b) Performance Only the requirements of paragraph

requirements 6.1.5.4 and paragraph 6.3 on door
(Paragraph 6 of locks shall apply.
UNECE Regulation
No 11)
02007L0046 — EN — 18.01.2018 — 021.001 — 165
▼M14
7A Audible warning Regulation (a) Components X

devices and signals (EC) No 661/
2009
UNECE Regu (b) Installation on vehicle B
lation No 28
8A Devices for indirect Regulation (a) Components X

vision and their (EC) No 661/
installation 2009
UNECE Regu (b) Installation on vehicle B
lation No 46
9B Braking Regulation (a) Design and tests A

(EC) No 661/ requirements
2009
UNECE Regu
lation No 13-H (b) Electronic stability The fitting of BAS and ESC shall not
control (ESC) and be required. If fitted, they shall
brake assist comply with the requirements of
systems(BAS) UNECE Regulation No 13-H.
10A Electromagnetic Regulation B

compatibility (EC) No 661/
2009
UNECE Regu
lation No 10
12A Interior fittings Regulation C

(EC) No 661/
2009
UNECE Regu (a) Interior arrangement
lation No 21
(i) Radii and The requirements of paragraphs 5.1 to
protrusion 5.6 of UNECE Regulation No 21 may
requirements be waived at the request of the manu
for switches, facturer.
pull-knobs and
The requirements of paragraph 5.2 of
the like,
UNECE Regulation No 21 with the
controls and
exception of paragraphs 5.2.3.1,
general interior
5.2.3.2 and 5.2.4 shall apply.
fittings
(ii) Energy Energy absorption tests on the upper

absorption tests dashboard shall only be performed
on the upper when the vehicle is not fitted with at
dashboard least two front airbags or two static
four-point harnesses.
(iii) Energy N/A

absorption test
on the rear part
of the seats
(b) Power-operation of All requirements of paragraph 5.8

windows, roof-panel UNECE Regulation No 21 shall
systems and apply.
partition systems
02007L0046 — EN — 18.01.2018 — 021.001 — 166
▼M14
▼M26
13A Protection of motor Regulation A

vehicles against (EC) No 661/
The provisions of paragraph 8.3.1.1.1
unauthorised use 2009
of UNECE Regulation No 116 may be
UNECE Regu applied instead of paragraph 8.3.1.1.2
lation No 116 of that Regulation regardless of the
type of powertrain
▼M14
14A Protection of the Regulation C

driver against the (EC) No 661/
steering mechanism 2009
in the event of Tests are required when the vehicle
UNECE Regu has not been tested under UNECE
impact
lation No 12 Regulation No 94 (see item 53A)
15A Seats, their Regulation C

anchorages and any (EC) No 661/
head restraints 2009
(a) General Requirements of paragraph 5.2 of
UNECE Regu requirements UNECE Regulation No 17 shall
lation No 17 apply with the exception of
(i) Specifications
paragraph 5.2.3.
(ii) Strength tests The requirements of paragraph 6.2

for seat UNECE Regulation No 17 shall
backrest and apply.
head restraints
(iii) Unlocking and The test shall be performed in

adjustment tests accordance with the requirements of
Annex 7 to UNECE Regulation
No 17.
(b) Head restraints Requirements of paragraphs 5.4, 5.5,

5.6, 5.10, 5.11 and 5.12 of UNECE
(i) Specifications
Regulation No 17 shall apply with
the exception of paragraph 5.5.2.
(ii) Strength tests The test prescribed in paragraph 6.4

on head shall be performed.
restraints
(c) Special requirements The requirements of Annex 9 to

regarding the UNECE Regulation No 26 may be
protection of waived at the request of the
occupants from manufacturer.
displaced luggage
16A External Regulation C

projections (EC) No 661/
2009
(a) General specificat The requirements of paragraph 5 of
UNECE Regu ions UNECE Regulation No 26 shall
lation No 26 apply.
(b) Particular specificat The requirements of paragraph 6 of

ions UNECE Regulation No 26 shall
apply.
02007L0046 — EN — 18.01.2018 — 021.001 — 167
▼M14
17A Vehicle access and Regulation D

manoeuvrability (EC) No 661/
2009
Regulation
(EU) No 130/
2012
17B Speedometer Regulation B

equipment (EC) No 661/
including its instal 2009
lation
UNECE Regu
lation No 39
18A Manufacturer’s Regulation B

statutory plate and (EC) No 661/
vehicle identifi 2009
cation number
Regulation
(EU) No 19/
2011
19A Safety-belt Regulation B

anchorages, Isofix (EC) No 661/
anchorages systems 2009
and Isofix top
UNECE Regu
tether anchorages
lation No 14
20A Installation of Regulation B

lighting and (EC) No 661/
Daytime Running Lights (DRL) shall
light-signalling 2009
be fitted to a new vehicle type in
devices on vehicles
UNECE Regu accordance with Article 2 of
lation No 48 Directive 2008/89/EC.
21A Retro-reflecting Regulation X

devices for (EC) No 661/
power-driven 2009
vehicles and their
UNECE Regu
trailers
lation No 3
22A Front and rear Regulation X

position lamps, (EC) No 661/
stop-lamps and 2009
end-outline marker
UNECE Regu
lamps for motor
lation No 7
vehicles and their
trailers
22B Daytime running Regulation X

lamps for (EC) No 661/
power-driven 2009
vehicles
UNECE Regu
lation No 87
22C Side-marker lamps Regulation X

for motor vehicles (EC) No 661/
and their trailers 2009
UNECE Regu
lation No 91
02007L0046 — EN — 18.01.2018 — 021.001 — 168
▼M14
23A Direction indicators Regulation X

for power-driven (EC) No 661/
vehicles and their 2009
trailers
UNECE Regu
lation No 6
24A Illumination of Regulation X

rear-registration (EC) No 661/
plates of 2009
power-driven
UNECE Regu
vehicles and their
lation No 4
trailers
25A Power-driven Regulation X

vehicle’s (EC) No 661/
sealed-beam 2009
headlamps (SB)
UNECE Regu
emitting an
lation No 31
European asym
metrical passing
beam or a driving
beam or both
25B Filament lamps for Regulation X

use in approved (EC) No 661/
lamp units of 2009
power-driven
UNECE Regu
vehicles and their
lation No 37
trailers
25C Motor vehicle Regulation X

headlamps (EC) No 661/
equipped with 2009
gas-discharge light
UNECE Regu
sources
lation No 98
25D Gas-discharge light Regulation X

sources for use in (EC) No 661/
approved 2009
gas-discharge lamp
UNECE Regu
units of
lation No 99
power-driven
vehicles
25E Motor vehicle Regulation X

headlamps emitting (EC) No 661/
an asymmetrical 2009
passing beam or a
UNECE Regu
driving beam or
lation No 112
both and equipped
with filament
lamps and/or LED
modules
02007L0046 — EN — 18.01.2018 — 021.001 — 169
▼M14
25F Adaptive Regulation X

front-lighting (EC) No 661/
systems (AFS) for 2009
motor vehicles
UNECE Regu
lation No 123
26A Power-driven Regulation X

vehicle front fog (EC) No 661/
lamps 2009
UNECE Regu
lation No 19
27A Towing device Regulation B

(EC) No 661/
2009
Regulation
(EU) No 1005/
2010
28A Rear fog lamps for Regulation X

power-driven (EC) No 661/
trailers
UNECE Regu
lation No 38
29A Reversing lights Regulation X

for power-driven (EC) No 661/
trailers
UNECE Regu
lation No 23
30A Parking lamps for Regulation X

power-driven (EC) No 661/
vehicles 2009
UNECE Regu
lation No 77
31A Safety-belts, Regulation (a) Components X

restraint systems, (EC) No 661/
child restraint 2009
systems and Isofix
UNECE Regu (b) Installation B
child restraint requirements
lation No 16
systems
32A Forward field of Regulation A

vision (EC) No 661/
2009
UNECE Regu
lation No 125
33A Location and Regulation A

identification of (EC) No 661/
hand controls, 2009
tell-tales and
UNECE Regu
indicators
lation No 121
02007L0046 — EN — 18.01.2018 — 021.001 — 170
▼M14
34A Windscreen Regulation C

defrosting and (EC) No 661/
demisting systems 2009
(a) Windscreen Only paragraph 1.1.1 of Annex II to
Regulation defrosting Regulation (EU) No 672/2010 shall
(EU) No 672/ apply provided that warm air flow is
2010 ducted to the whole surface of the
windscreen or the latter is electrically
heated on its whole surface.
(b) Windscreen Only point 1.2.1 of Annex II to

demisting Regulation (EU) No 672/2010 shall
apply provided that warm air flow is
ducted to the whole surface of the
windscreen or the latter is electrically
heated on its whole surface.
35A Windscreen wiper Regulation C

and washer (EC) No 661/
systems 2009
(a) Windscreen wiper Paragraphs 1.1 to 1.1.10 of Annex III
Regulation system to Regulation (EU) No 1008/2010
(EU) No 1008/ shall apply.
2010
Only the test described in paragraph
2.1.10 of Annex III to
Regulation (EU) No 1008/2010 shall
be performed.
(b) Windscreen washer Section 1.2 of Annex III to

system Regulation (EU) No 1008/2010 shall
apply with the exception of points
1.2.2, 1.2.3 and 1.2.5.
36A Heating system Regulation C

(EC) No 661/
The fitting of a heating system shall
2009
not be required.
UNECE Regu
lation No 122
(a) All heating systems The requirements of paragraph 5.3 and
of paragraph 6 of UNECE Regulation
No 122 shall apply.
(b) LPG heating systems The requirements of Annex 8 to

UNECE Regulation No 122 shall
apply.
37A Wheel guards Regulation B

(EC) No 661/
2009
Regulation
(EU) No 1009/
2010
▼M22
38A Head restraints Regulation X

(EC) No 661/
2009
UNECE Regu
lation No 25
02007L0046 — EN — 18.01.2018 — 021.001 — 171
▼M14
▼M5
_____
▼M20
41A Emissions (Euro Regulation A

VI) heavy duty (EC) No 595/
With the exception of the set of
vehicles/ access to 2009
requirements relating to OBDs and
information
access to information.
Power measurement (When the vehicle manufacturer uses

same ECU).
▼M14
44A Masses and Regulation B

dimensions (EC) No 661/
The hill start test at maximum combi
2009
nation mass described in paragraph
Regulation 5.1 of Part A of Annex 1 to
(EU) No 1230/ Regulation (EU) No 1230/2012 may
2012 be waived at the request of the
manufacturer.
45A Safety glazing Regulation (a) Components X

materials and their (EC) No 661/
installation on 2009
vehicles (b) Installation B
UNECE Regu
lation No 43
▼M6
_____
▼M14
46A Installation of tyres Regulation B

(EC) No 661/
Dates for progressive application shall
2009
be those set out in Article 13 of Regu
Regulation lation (EC) No 661/2009.
(EU) No 458/
2011
46B Pneumatic tyres for Regulation Components X

motor vehicles and (EC) No 661/
their trailers (Class 2009
C1)
UNECE Regu
lation No 30
02007L0046 — EN — 18.01.2018 — 021.001 — 172
▼M14
46D Tyre rolling sound Regulation Components X

emissions, (EC) No 661/
adhesion on wet 2009
surfaces and rolling
UNECE Regu
resistance (classes
lation No 117
C1, C2 and C3)
46E Temporary-use Regulation Components X

spare unit, run-flat (EC) No 661/
tyres/system and 2009
tyre pressure
UNECE Regu
monitoring system Fitting of a tyre-pressure B
lation No 64
monitoring system
The fitting of a TPMS shall not be
(TPMS)
required.
50A Mechanical Regulation (a) Components X

coupling (EC) No 661/
components of 2009
combinations of
UNECE Regu
vehicles (b) Installation B
lation No 55
53A Protection of Regulation C

occupants in the (EC) No 661/
The requirements of UNECE Regu
event of a frontal 2009
lation No 94 shall apply to vehicles
collision
UNECE Regu fitted with front airbags. Vehicles not
lation No 94 fitted with airbags shall fulfil the
requirement of item 14A of this table.
54A Protection of Regulation C

(shall apply from 1 November 2014)
event of lateral 2009
collision
UNECE Regu
lation No 95
Head form test The manufacturer shall supply the
technical service with suitable
information concerning a possible
impact of the head of the dummy
against the structure of the vehicle or
the side glazing if made up of
laminated glazing.
When such impact is proven likely to
happen, then the partial test using the
head form test described in paragraph
3.1 of Annex 8 to UNECE Regulation
No 95 shall be conducted and the
criterion specified in paragraph
5.2.1.1 of UNECE Regulation 95
shall be met.
In agreement with the technical
service, the test procedure described
in Annex 4 to UNECE Regulation
No 21 may be used as an alternative
to the test mentioned above.
02007L0046 — EN — 18.01.2018 — 021.001 — 173
▼M14
58 Pedestrian Regulation (a) Technical N/A

protection (EC) No 78/ requirements
2009 applicable to vehicle
(b) Frontal protection X

systems
59 Recyclability Directive N/A

2005/64/EC
Only Article 7 on reuse of component
parts shall apply.
61 Air-conditioning Directive A
systems 2006/40/EC
Fluorinated greenhouse gases with a
global warming potential higher than
150 are permitted until 31 December
2016.
62 Hydrogen system Regulation X

(EC) No 79/
2009
▼M26
63 General Safety Regulation See footnote (15) of the table in Part I

(EC) No 661/ of Annex IV with regulatory acts for
2009 EC type-approval of vehicles
produced in unlimited series
▼M14
64 Gear shift Regulation N/A

indicators (EC) No 661/
2009
Regulation
(EU) No 65/
2012
67 Specific Regulation (a) Components X

components for (EC) No 661/
liquefied petroleum 2009
gases (LPG) and (b) Installation A
UNECE Regu
their installation on
lation No 67
motor vehicles
68 Vehicle alarm Regulation (a) Components X

systems (VAS) (EC) No 661/
2009
(b) Installation B
UNECE Regu
lation No 97
69 Electric safety Regulation B

(EC) No 661/
2009
UNECE Regu
lation No 100
02007L0046 — EN — 18.01.2018 — 021.001 — 174
▼M14
70 Specific Regulation (a) Components X

CNG and their 2009 (b) Installation A
installation on
UNECE Regu
motor vehicles
lation No 110
Meaning of letters
X Full application of the regulatory act.
(a) a type-approval certificate shall be issued;
(b) tests and checks shall be conducted by the technical service or the manufacturer under the
conditions laid down in Articles 41, 42 and 43;
(c) a test report shall be drafted in accordance with the provisions of Annex V;
(d) Conformity of Production (COP) shall be ensured.
A Application of the regulatory act as follows:
(a) all requirements of the regulatory act shall be fulfilled unless otherwise stated;
(b) no type-approval certificate shall be required;
(c) tests and checks shall be conducted by the technical service or the manufacturer under the
conditions laid down in Articles 41, 42 and 43;
(d) a test report shall be drafted in accordance with the provisions of Annex V;
(e) COP shall be ensured.
B Application of the regulatory act as follows:
As for letter ‘A’ with the exception that the tests and checks may be performed by the manufacturer
himself subject to the agreement of the type-approval authority (i.e. the conditions laid down in
Articles 41, 42 and 43 do not have to be fulfilled).
C Application of the regulatory act as follows:
(a) only the technical requirements from the regulatory shall be fulfilled, irrespective of any transi
tional provision;
(b) no type-approval certificate shall be required;
(c) tests and checks shall be conducted by the technical service or by the manufacturer (see decisions
for letter ‘B’);
(d) a test report shall be drafted in accordance with the provisions of Annex V;
(e) COP shall be ensured.
D Same as for decisions in letters ‘B’ and ‘C’ with the exception that a statement of compliance
submitted by the manufacturer is sufficient. No test report shall be required.
The type-approval authority or technical service may require additional information of further
evidence, if need be.
N/A The regulatory act shall not apply. Compliance with one or more specific aspects included in the
regulatory act may however be imposed.
Note: The series of amendments of the UNECE Regulations to be used are listed in Annex IV to Regulation (EC) No 661/2009.
Series of amendments adopted subsequently are accepted as an alternative.
02007L0046 — EN — 18.01.2018 — 021.001 — 175
▼M14
Table 2
N1 vehicles (1)
1 Permissible sound Directive 70/ A

level 157/EEC
▼M23
1A Sound level Regulation (EU) A

No 540/2014
▼M20
2 Emissions (Euro 5 Regulation (EC) A

and 6) light duty No 715/2007
vehicles/access to (a) On-board The vehicle shall be fitted with an
information diagnostic (OBD) OBD system that fulfils the
requirements of Article 4(1) and (2)
of Regulation (EC) No 692/ 2008
(The OBD system shall be designed
to record at least the malfunction of
the engine management system).
The OBD-interface shall be able to
communicate with commonly
available diagnostic tools.
(b) In service confor N/A

mity
(c) Access to infor It is sufficient that the manufacturer

mation provide access to repair and main
tenance information in a readily
accessible and prompt manner.
(d) Power measure (When the vehicle manufacturer uses

ment an engine from another manufacturer)
same ECU).
▼M14
3A Prevention of fire Regulation (EC) (a) Liquid fuel tanks B

risks (liquid fuel No 661/2009
tanks) (b) Installation in B
UNECE Regu
lation No 34 vehicle
▼M22
3B Rear underrun Regulation (EC) B

protective devices No 661/2009
(RUPDs) and their
UNECE Regu
installation; rear
lation No 58
underrun
protection (RUP)
(1) The explanatory notes relating to Part I of Annex IV apply also to Table 2. The letters in
Table 2 have the same meaning as in Table 1.
02007L0046 — EN — 18.01.2018 — 021.001 — 176
▼M14
4A Space for mounting Regulation (EC) B

and fixing rear No 661/2009
registration plates
Regulation (EU)
No 1003/2010
5A Steering equipment Regulation (EC) C

No 661/2009
UNECE Regu
lation No 79 (a) Mechanical The provisions of paragraph 5 of
systems UNECE Regulation No 79.01 shall
apply.
All tests prescribed in paragraph 6.2
of UNECE Regulation No 79 shall
be performed and the requirements of
paragraph 6.1 of UNECE Regulation
No 79 shall apply.
(b) Complex elec All the requirements of Annex 6 of

tronic vehicle UNECE Regulation No 79 shall
control system apply.
Compliance with these requirements
may only be checked by an
appointed technical service.
6A Door latches and Regulation (EC) C

door retention No 661/2009
components
UNECE Regu
lation No 11 (a) General All requirements shall apply.
requirements
(Paragraph 5 of
UNECE Regu
lation No 11)
(b) Performance Only the requirements of paragraph

requirements 6.1.5.4 and paragraph 6.3 on door
(Paragraph 6 of locks shall apply.
UNECE Regu
lation No 11)
7A Audible warning Regulation (EC) (a) Components X

devices and signals No 661/2009
UNECE Regu
lation No 28 (b) Installation on B
vehicle
8A Devices for indirect Regulation (EC) (a) Components X

vision and their No 661/2009
installation
UNECE Regu
lation No 46 (b) Installation on B
vehicle
9A Braking of vehicles Regulation (EC) (a) design and test A

and trailers No 661/2009 requirements
UNECE Regu
lation No 13.
(b) ESC The fitting of ESC shall not be
required. If fitted, it shall comply
with the requirements of UNECE
Regulation No 13.
02007L0046 — EN — 18.01.2018 — 021.001 — 177
▼M14
9B Braking of Regulation (EC) (a) Design and test A

passenger cars No 661/2009 requirements
UNECE Regu
lation No 13-H (b) Electronic stability The fitting of BAS and ESC shall not
control (ESC) and be required. If fitted, they shall
brake assist comply with the requirements of
systems(BAS) UNECE Regulation No 13-H.
10A Electromagnetic Regulation (EC) B

compatibility No 661/2009
UNECE Regu
lation No 10
▼M26
13A Protection of motor Regulation (EC) A

vehicles against No 661/2009
The provisions of paragraph 8.3.1.1.1
unauthorised use
UNECE Regu of UNECE Regulation No 116 may be
lation No 116 applied instead of paragraph 8.3.1.1.2
of that Regulation regardless of the
type of powertrain
▼M14
14A Protection of the Regulation (EC) C

driver against the No 661/2009
steering mechanism
UNECE Regu (a) Barrier impact test A test shall be required.
in the event of
lation No 12
impact
(b) Body block im- Not required if the steering wheel is

pact test against fitted with an airbag.
steering wheel
(c) Head form test Not required if the steering wheel is

fitted with an airbag.
15A Seats, their Regulation (EC) B

anchorages and any No 661/2009
head restraints
UNECE Regu
lation N 17
17A Vehicle access and Regulation (EC) D

manoeuvrability No 661/2009
Regulation (EU)
No 130/2012
17B Speedometer Regulation (EC) B

equipment No 661/2009
including its instal
UNECE Regu
lation
lation No 39
18A Manufacturer’s Regulation (EC) B

statutory plate and No 661/2009
vehicle identifi
Regulation (EU)
cation number
No 19/2011
02007L0046 — EN — 18.01.2018 — 021.001 — 178
▼M14
19A Safety-belt Regulation (EC) B

anchorages, Isofix No 661/2009
anchorages systems
UNECE Regu
and Isofix top
lation No 14
tether anchorages
20A Installation of Regulation (EC) B

lighting and No 661/2009
DRLs shall be fitted to a new vehicle
light-signalling
UNECE Regu type in accordance with Article 2 of
devices on motor
lation No 48 Directive 2008/89/EC.
vehicles
21A Retro-reflecting Regulation (EC) X

devices for No 661/2009
power-driven
UNECE Regu
vehicles and their
lation No 3
trailers
22A Front and rear Regulation (EC) X

position lamps, No 661/2009
stop-lamps and
UNECE Regu
end-outline marker
lation No 7
lamps for motor
vehicles and their
trailers
22B Daytime running Regulation (EC) X

lamps for No 661/2009
power-driven
UNECE Regu
vehicles
lation No 87
22C Side-marker lamps Regulation (EC) X

for motor vehicles No 661/2009
and their trailers
UNECE Regu
lation No 91
23A Direction indicators Regulation (EC) X

for power-driven No 661/2009
vehicles and their
UNECE Regu
trailers
lation No 6
24A Illumination of Regulation (EC) X

rear-registration No 661/2009
plates of
UNECE Regu
power-driven
lation No 4
vehicles and their
trailers
02007L0046 — EN — 18.01.2018 — 021.001 — 179
▼M14
25A Power-driven Regulation (EC) X

vehicle’s No 661/2009
sealed-beam
UNECE Regu
headlamps (SB)
lation No 31
emitting an
European asym
metrical passing
beam or a driving
beam or both
25B Filament lamps for Regulation (EC) X

use in approved No 661/2009
lamp units of
UNECE Regu
power-driven
lation No 37
vehicles and their
trailers
25C Motor vehicle Regulation (EC) X

headlamps No 661/2009
equipped with
UNECE Regu
gas-discharge light
lation No 98
sources
25D Gas-discharge light Regulation (EC) X

sources for use in No 661/2009
approved
UNECE Regu
gas-discharge lamp
lation No 99
units of
power-driven
vehicles
25E Motor vehicle Regulation (EC) X

headlamps emitting No 661/2009
an asymmetrical
UNECE Regu
passing beam or a
lation No 112
driving beam or
both and equipped
with filament
lamps and/or LED
modules
25F Adaptive Regulation (EC) X

front-lighting No 661/2009
systems (AFS) for
UNECE Regu
motor vehicles
lation No 123
26A Power-driven Regulation (EC) X

vehicle front fog No 661/2009
lamps
UNECE Regu
lation No 19
02007L0046 — EN — 18.01.2018 — 021.001 — 180
▼M14
27A Towing device Regulation (EC) B

No 661/2009
Regulation (EU)
No 1005/2010
28A Rear fog lamps for Regulation (EC) X

power-driven No 661/2009
vehicles and their
UNECE Regu
trailers
lation No 38
29A Reversing lights Regulation (EC) X

for power-driven No 661/2009
vehicles and their
UNECE Regu
trailers
lation No 23
30A Parking lamps for Regulation (EC) X

power-driven No 661/2009
vehicles
UNECE Regu
lation No 77
31A Safety-belts, Regulation (EC) (a) Components X

restraint systems, No 661/2009
child restraint
UNECE Regu
systems and Isofix
lation No 16 (b) Installation B
child restraint
systems requirements
33A Location and Regulation (EC) A

identification of No 661/2009
hand controls,
UNECE Regu
tell-tales and
lation No 121
indicators
34A Windscreen Regulation (EC) N/A

defrosting and No 661/2009
The vehicle shall be fitted with a
demisting systems
Regulation (EU) suitable windscreen defrosting and
No 672/2010 demisting system.
35A Windscreen wiper Regulation (EC) N/A

and washer No 661/2009
The vehicle shall be fitted with a
systems
Regulation (EU) suitable windscreen wiper and washer
No 1008/2010 system.
36A Heating system Regulation (EC) C

No 661/2009
The fitting of a heating system shall
UNECE Regu not be required.
lation No 122
(a) All heating syste- The requirements of paragraph 5.3 and

ms of paragraph 6 of UNECE Regulation
No 122 shall apply.
02007L0046 — EN — 18.01.2018 — 021.001 — 181
▼M14
(b) LPG heating sys- The requirements of Annex 8 to

tems UNECE Regulation No 122 shall
apply.
▼M22
_____
▼M5
_____
▼M20
41A Emissions (Euro Regulation (EC) A

VI) heavy duty No 595/2009
With the exception of the set of
vehicles/ access to
requirements relating to OBDs and
information
access to information.
Power measurement (When the vehicle manufacturer uses

same ECU).
▼M14
43A Spray suppression Regulation (EC) B

systems No 661/2009
Regulation (EU)
No 109/2011
45A Safety glazing Regulation (EC) (a) Components X

materials and their No 661/2009
installation on
UNECE Regu
vehicles
46 Tyres Directive 92/23/ Components X

EEC
46A Installation of tyres Regulation (EC) B

No 661/2009
Dates for progressive application shall
Regulation (EU) be those set out in Article 13 of Regu
No 458/2011 lation (EC) No 661/2009.
02007L0046 — EN — 18.01.2018 — 021.001 — 182
▼M14
46B Pneumatic tyres for Regulation (EC) Components X

motor vehicles and No 661/2009
their trailers (Class
UNECE Regu
C1)
lation No 30
46C Pneumatic tyres for Regulation (EC) Components X

commercial No 661/2009
vehicles and their
UNECE Regu
trailers (Classes C2
lation No 54
and C3)
46D Tyre rolling sound Regulation (EC) Components X

emissions, No 661/2009
adhesion on wet
UNECE Regu
surfaces and rolling
lation No 117
resistance (Classes
C1, C2 and C3)
46E Temporary-use Regulation (EC) Components X

spare unit, run-flat No 661/2009
tyres/system and
UNECE Regu
tyre pressure
lation No 64 Fitting of a tyre- B
monitoring system
pressure monitoring
The fitting of a TPMS shall not be
system
required
48 Masses and Directive 97/27/ B

dimensions EC
48A Masses and Regulation (EC) B

dimensions No 661/2009
Regulation (EU)
No 1230/2012 Hill start test at The hill start test at maximum combi
maximum combi nation mass described in paragraph
nation mass 5.1 of Part A of Annex 1 to
Regulation (EU) No 1230/2012 may
be waived at the request of the
manufacturer.
49A Commercial Regulation (EC) C

vehicles with No 661/2009
regards to their
UNECE Regu
external projections
lation No 61 (a) General specifi The requirements of paragraph 5 of
forward of the
cations UNECE Regulation No 61 shall apply
cab’s rear panel
(b) Particular specifi The requirements of paragraph 6 of

cations UNECE Regulation No 61 shall
apply.
50A Mechanical Regulation (EC) (a) Components X

coupling No 661/2009
components of
UNECE Regu
combinations of
vehicles
02007L0046 — EN — 18.01.2018 — 021.001 — 183
▼M14
54A Protection of Regulation (EC) C C

occupants in the No 661/2009
event of lateral
UNECE Regu
collision Head form test The manufacturer shall supply the
lation No 95
technical service with suitable
information concerning a possible
impact of the head of the dummy
against the structure of the vehicle or
the side glazing if made up of
laminated glazing.
When such impact is proven likely to
happen, then the partial test using the
head form test described in paragraph
3.1 of Annex 8 to UNECE Regulation
No 95 shall be conducted and the
criterion specified in paragraph
5.2.1.1 of UNECE Regulation 95
shall be met.
In agreement with the technical
service, the test procedure described
in Annex 4 to UNECE Regulation
No 21 may be used as an alternative
to the test mentioned above.
56 Vehicles for the Regulation (EC) A

carriage of No 661/2009
dangerous goods
UNECE Regu
lation No 105
58 Pedestrian Regulation (EC) (a) Technical N/A

protection No 78/2009 requirements
applicable to a
vehicle
(b) Frontal protection X

systems
59 Recyclability Directive 2005/ N/A

64/EC
Only Article 7 on reuse of component
parts shall apply.
61 Air-conditioning Directive 2006/ B

systems 40/EC
Fluorinated greenhouse gases with a
global warming potential higher than
150 are permitted until 31 December
2016.
62 Hydrogen system Regulation (EC) X

No 79/2009
▼M26
63 General Safety Regulation (EC) See footnote (15) of the table in Part I
No 661/2009 of Annex IV with regulatory acts for
EC type-approval of vehicles
produced in unlimited series
02007L0046 — EN — 18.01.2018 — 021.001 — 184
▼M14
67 Specific Regulation (EC) (a) Components X

components for No 661/2009
liquefied petroleum (b) Installation A
UNECE Regu
gases (LPG) and
lation No 67
their installation on
motor vehicles
68 Vehicle alarm Regulation (EC) (a) Components X

systems (VAS) No 661/2009
UNECE Regu (b) Installation B
lation No 97
69 Electric safety Regulation (EC) B

No 661/2009
UNECE Regu
lation No 100
70 Specific Regulation (EC) (a) Components X

components for No 661/2009
CNG and their (b) Installation A
UNECE Regu
installation on
lation No 110
motor vehicles
▼M26
71 Cab strength Regulation (EC) C

No 661/2009
UNECE Regu
lation No 29
02007L0046 — EN — 18.01.2018 — 021.001 — 185
▼M10
Appendix 2
Requirements for the approval pursuant to Article 24 of complete vehicles

belonging to category M1 and N1, produced in large series in or for third
countries
0. OBJECTIVE
A vehicle is deemed to be new where:
(a) it has never been registered previously; or
(b) it has been registered for less than 6 months at the time of the appli
cation for individual approval.
A vehicle shall be considered registered where it has obtained a

permanent, temporary or short-term administrative authorisation for
entry into service in road traffic, involving its identification and the
issuing of a registration number (1).
1. ADMINISTRATIVE PROVISIONS
1.1. Categorisation of the vehicle
Vehicles shall be categorised according to the criteria set out in Annex II.
For such purposes:
(a) the actual number of seating positions shall be taken into consideration;
and
(b) the technically maximum permissible laden mass shall be the maximum
mass stated by the manufacturer in the country of origin and available
in his official documentation.
Where it is not possible to easily determine the vehicle category because of

the design of the bodywork, the conditions set out in Annex II shall apply.
1.2 Application for individual approval

(a) The applicant shall submit an application to the approval authority
accompanied by all relevant documentation necessary for the
operation of the approval process.
Where the submitted documentation is incomplete, falsified or forged

the application for approval shall be rejected.
(b) Only one application for a particular vehicle may be submitted in only
one Member State.
By a particular vehicle, it shall be understood a physical vehicle the

vehicle identification number of which is clearly identified.
For the application of this point, the approval authority may require that
the applicant commits himself in writing that he will submit only one
application in one Member State.
However, any applicant may apply for individual approval in another

Member States in respect of a vehicle that has technical characteristics
identical or similar to the one that has been granted an individual
approval.
(c) The model of the application form and the layout of the file shall be
laid down by the approval authority.
Particulars may only consist in an appropriate selection of the

information included in Annex I.
(1) In the absence of a registration document, the competent authority may refer to available
documented evidence of date of manufacture or documented evidence of first purchase.
02007L0046 — EN — 18.01.2018 — 021.001 — 186
▼M10
(d) The technical requirements to be satisfied are those laid down in
Section 4 of this Appendix.
They shall be those applicable to new vehicles belonging to a vehicle

type currently in production, in relation to the date of the submission of
the application.
(e) With respect to certain tests required in some regulatory acts listed in
this Annex, the applicant shall supply a statement of compliance with
recognised international standards or regulations. The statement in
question may only be issued by the vehicle manufacturer.
‘Statement of compliance’ shall mean a statement issued by the office

or department within the manufacturer’s organisation which is duly
authorised by the management to fully engage the legal responsibility
of the manufacturer with respect to the design and the construction of a
vehicle.
The regulatory acts for which such a statement has to be supplied shall
be those referred to in Section 4 of this Appendix.
Where a statement gives rise to uncertainty, the applicant may be

required to obtain from the manufacturer a conclusive piece of
evidence, including a test report, in order to corroborate the manu
facturer’s statement.
1.3. Technical services entrusted with individual approvals

(a) The technical services entrusted with individual approvals shall be of
category A as referred to in Article 41(3).
(b) By way of derogation from the second subparagraph of Article 41(4),

technical services shall comply with the following standards:
(i) EN ISO/IEC 17025:2005 when they perform tests themselves;
(ii) EN ISO/IEC 17020:2004 when they check compliance of the

vehicle with the requirements included in this Appendix.
(c) Where specific tests requiring specific skills have to be conducted at the
request of the applicant, they shall be conducted by one of the technical
services notified to the Commission at the choice of the applicant.
For example, where a frontal impact test has to be conducted in

agreement with the applicant in a Member State ‘A’, the test may be
conducted by a notified technical service in a Member State ‘B’.
1.4. Test reports

(a) Test reports shall be drafted in accordance with Section 5.10.2 of
Standard EN ISO/IEC 17025:2005.
(b) They shall be drafted in one of the languages of the Union determined
by the approval authority.
Where in application of point 1.3(c) a test report has been established in

a Member State other than the one entrusted with the individual
approval, the approval authority may require that the applicant
submits a true translation of the test report.
02007L0046 — EN — 18.01.2018 — 021.001 — 187
▼M10
(c) They shall include a description of the vehicle tested including unam
biguous identification. The parts which play a significant role with
regard to the results of the tests shall be described and their identifi
cation number reported.
Examples of parts include the silencers for noise measurement and the
engine management system (ECU) for the measurement of tailpipe
emissions.
(d) At the request of an applicant, a test report delivered for a system

related to a particular vehicle may be presented repeatedly either by
the same or another applicant for the purposes of individual approval of
another vehicle.
In such a case the approval authority shall ensure that the technical
characteristics of the vehicle are properly inspected against the test
report.
Inspection of the vehicle and the documentation accompanying the test

report shall lead to the conclusion that the vehicle for which an indi
vidual approval is sought has the same characteristics as the vehicle
described in the report.
(e) Only authenticated copies of a test report may be submitted.
(f) Test reports referred to in point 1.4(d) do not include the reports drawn
up in order to grant the vehicle individual approval.
1.5. It is inherent in the individual approval process that each particular vehicle
is inspected physically by the technical service.
No exemption to this principle shall be permitted.
1.6. Where the approval authority is satisfied that the vehicle meets the technical
requirements specified in this Appendix and conforms to the description
included in the application it shall grant approval in accordance with
Article 24.
1.7. The certificate of approval shall be drafted according to Model D as laid

down in Annex VI.
1.8. The approval authority shall keep record of all approvals granted under
Article 24.
2. EXEMPTIONS
2.1. Due to the specific nature of the individual procedure, the following Articles
of this Directive including the respective provisions in the relevant annexes
shall be waived:
(a) Article 12 relating to conformity of production arrangements;
(b) Articles 8, 9, 13, 14 and 18 relating to vehicle type-approval procedure.
2.2. Vehicle type identification

(a) As far as possible, the type, the variant and the version which is given
in its country of origin shall be referred to in the approval certificate.
(b) Where it is not possible to identify the type, the variant and the version
because of the absence of appropriate data, the usual commercial name
of the vehicle may be referred to.
3. REVIEW OF THE TECHNICAL REQUIREMENTS

The list of the technical requirements included in Section 4 will be regularly
reviewed in order to take account of the results of the harmonisation work
in progress at the World Forum for Harmonization of Vehicle Regulations
(WP.29) in Geneva and legislative developments in the third countries.
02007L0046 — EN — 18.01.2018 — 021.001 — 188
▼M10
4. TECHNICAL REQUIREMENTS
Part I: Vehicles belonging to category M1
Item Regulatory act reference Alternative requirements
1 Directive 70/157/EEC Drive-by test
(Permissible sound level) (a) A test shall be conducted in accordance with the ‘Method A’
referred to in Annex 3 to UNECE Regulation No 51.
Limits are those specified in Section 2.1 of Annex I to Directive 70/

157/EEC. 1 decibel in addition to the permitted limits shall be
allowed.
(b) The test track shall comply with Annex 8 to UNECE Regulation
No 51. A test track having different specifications may be used
under the condition that correlation tests have been conducted by
the technical service. A correction factor shall be applied if
necessary.
(c) Exhaust systems containing fibrous materials need not be condi

tioned as prescribed in Annex 5 to UNECE Regulation No 51.
Stationary test
A test shall be conducted in accordance with Section 3.2 of Annex 3 to

UNECE Regulation No 51.
2 Directive 70/220/EEC Tailpipe emissions
(Emissions) (a) A type I test shall be conducted in accordance with Annex III to
Directive 70/220/EEC using the deterioration factors referred to in
point 5.3.6.2. The limits to be applied shall be those specified in
point 5.3.1.4 of Annex I to that Directive.
(b) The vehicle shall not be required to exhibit 3 000 km as requested

in Section 3.1.1 of Annex III to that Directive.
(c) The fuel to be used for the test shall be the reference fuel as
prescribed in Annex IX to Directive 70/220/EEC.
(d) The dynamometer shall be set up in accordance with the technical

requirements of Section 3.2 of Appendix 2 to Annex III to that
Directive.
(e) The test referred to in point (a) shall not be conducted where it can
be demonstrated that the vehicle complies with one of the California
Regulations mentioned in the prefatory note to Section 5 of Annex I
to that Directive.
Evaporative emissions
Vehicles equipped with a petrol-fuelled engine shall be fitted with an

evaporate emissions control system (e.g. charcoal canister).
Crankcase emissions
The presence of a device for recycling crankcase gases shall be

required.
OBD
The vehicle shall be fitted with an OBD system.
OBD-interface shall be able to communicate with common diagnostic

tools used for periodic technical inspections.
02007L0046 — EN — 18.01.2018 — 021.001 — 189
▼M10
▼M20
2a Regulation (EC) No 715/ Tailpipe emissions

2007
(a) A type I test shall be conducted in accordance with Annex III to
(Emissions Euro 5 and 6 Regulation (EC) No 692/2008 using the deterioration factors set out
light duty vehicles/access in point 1.4 of Annex VII to Regulation (EC) No 692/2008. The
to information) limits to be applied shall be those specified in Table I and Table II
in Annex I to Regulation (EC) No 715/2007.
(b) The vehicle shall not be required to exhibit 3 000 km as mentioned

in Section 3.1.1 of Annex 4 to UNECE Regulation No 83.
prescribed in Annex IX to Regulation (EC) No 692/2008.

requirements set out in Section 3.2 of Annex 4 to UNECE Regu
lation No 83.
be shown that the vehicle complies with the California Regulations
referred to in Section 2 of Annex I to Regulation (EC) No 692/
2008.
For petrol-fuelled engines, the presence of an evaporate emissions

control system shall be required (e.g. a charcoal canister).
Crankcase emissions

required.
OBD
(a) The vehicle shall be fitted with an OBD system.
(b) OBD-interface must be able to communicate with common diag

nostic tools used for periodic technical inspections.
Smoke opacity
(a) Vehicles equipped with a diesel-fuelled engine shall be tested in

accordance with the tests methods referred to in Appendix 2 to
Annex IV to Regulation (EC) No 692/2008.
(b) The corrected value of the absorption coefficient shall be affixed

conspicuously and in a readily accessible place.
CO2 emissions and fuel consumption
(a) A test shall be conducted in accordance with Annex XII to


(c) Where the vehicle complies with the California Regulations referred
to in Section 2 of Annex I to Regulation (EC) No 692/2008 and
therefore no test of tailpipe emissions is required to be performed,
Member States shall calculate CO2 emissions and fuel consumption
with the formulæ laid down in the explanatory notes (b) and (c).
02007L0046 — EN — 18.01.2018 — 021.001 — 190
▼M20
Access to information
The provisions regarding access to information shall not apply.
Power measurement
(a) The applicant shall submit a statement from the manufacturer

stating the maximum engine power output in kW as well as the
corresponding engine speed in revolutions per minute.
(b) An engine power output curve providing the same information may
alternatively be referred to.
▼M10
3 Directive 70/221/EEC Fuel tanks
(Fuel tanks — Rear (a) Fuel tanks shall comply with Section 5 of Annex I to Directive 70/
protective devices) 221/EEC with the exception of points 5.1, 5.2 and 5.12. In
particular they shall comply with points 5.9 and 5.9.1 but no
dripping test shall be conducted.
(b) LPG or CNG tanks shall be type-approved in accordance with,

respectively UNECE Regulations 67 series of amendments 01 or
Regulation No 110 (a).
Specific provisions for fuel tanks made of a plastic material
The applicant shall submit a statement from the manufacturer estab

lishing that the fuel tank on the particular vehicle, [the VIN number
of which has to be specified], complies either with at least one of the
following:
— Section 6.3 of Directive 70/221/EEC,
— FMVSS No 301 (Fuel system integrity),
— Annex 5 to UNECE Regulation 34.
Rear protective device
(a) The rear part of the vehicle shall be constructed in accordance with
Section 5 of Annex II to Directive 70/221/EEC.
(b) For such purposes, it is sufficient that the requirements set out in
the second subparagraph of point 5.2 are fulfilled.
4 Directive 70/222/EEC Space, inclination, angles for visibility and position of the registration
plate shall comply with Directive 70/222/EEC.
(Rear registration plate
space)
5 Directive 70/311/EEC Mechanical systems
(Steering effort) (a) The steering mechanism shall be built as to self-centre. In order to
check compliance with this provision, a test shall be conducted in
accordance with points 5.1.2 and 5.2.1 of Annex I to Directive 70/
311/EEC.
(b) The failure of the power steering equipment shall not lead to a
complete loss of control of the vehicle.
Complex electronic vehicle control system (‘Drive-by wire’ devices)
Complex electronic control system shall be permitted only if they

comply with Annex 6 to UNECE Regulation No 79.
02007L0046 — EN — 18.01.2018 — 021.001 — 191
▼M10
6 Directive 70/387/EEC (a) Door latches and hinges shall comply with points 3.2.1, 3.3.2 and
3.4.1 of Annex I to Directive 70/387/EEC.
(Door latches and hinges)
(b) The requirements set out in point 3.4.1 shall not apply where
compliance with point 6.1.5.4 of UNECE Regulation No 11
Rev.1 Amendment 2 is demonstrated.
7 Directive 70/388/EEC Components
(Audible warning) The audible warning devices are not required to be type-approved in
accordance with Directive 70/388/EEC. However, they shall emit a
continuous sound as required in point 1.1 of Annex I to that Directive.
Installation on vehicle
(a) A test shall be conducted in accordance with Section 2 of Annex I

to Directive 70/388/EEC.
(b) The maximum sound pressure level shall be in accordance with

point 2.1.4 of that Annex.
8 Directive 2003/97/EC Components
(Indirect vision devices) (a) The vehicle shall be fitted with the rear-view mirrors prescribed in
Section 2 of Annex III to Directive 2003/97/EC.
(b) They are not required to be type-approved in accordance with that

Directive.
(c) The radii of curvature of the mirrors shall not cause significant
image distortions. At the discretion of the technical service, the
radii of curvature shall be checked in accordance with the method
described in Appendix 1 to Annex II to that Directive. The radii of
curvature shall not be less than those required by Section 3.4 of
Annex II to that Directive.
Measurement shall be conducted in order to ensure that the fields of

vision comply either with Section 5 of Annex III to Directive 2003/97/
EC or with Section 5 of Annex III to Directive 71/127/EEC.
9 Directive 71/320/EEC General provisions
(Braking) (a) The braking system shall be built in accordance with Section 2 of
Annex I to Directive 71/320/EEC.
(b) Vehicles shall be fitted with an electronic antilock braking system

acting on all wheels.
(c) The performances of the braking system shall comply with Section
2 of Annex II to that Directive.
(d) For these purposes, road tests shall be conducted on a track the
surface of which possesses high adhesion. The test on the parking
brake shall be conducted on a 18 % gradient (up and down).
Only those tests mentioned below shall be conducted. In each case,

the vehicle shall be in fully laden conditions.
(e) The road test referred to in point (c) above shall not be conducted
where the applicant can submit a statement from the manufacturer
establishing that the vehicle complies either with UNECE Regu
lation No 13-H including supplement 5 or with FMVSS No 135.
02007L0046 — EN — 18.01.2018 — 021.001 — 192
▼M10
Service brake
(a) A ‘Type 0’ test as prescribed in points 1.2.2 and 1.2.3 of Annex II

to Directive 71/320/EEC shall be conducted.
(b) In addition, a ‘Type I’ test as prescribed in point 1.3 of Annex II to

that Directive shall be conducted.
Parking brake
A test shall be conducted in accordance with point 2.1.3 of Annex II to

that Directive.
(Radio interference (elec (a) Electrical/electronic sub-assemblies are not required to be

tromagnetic compatibility)) type-approved in accordance with Directive 72/245/EEC.
(b) However, electric/electronic devices retrofitted shall comply with

that Directive.
Emitted electromagnetic radiations

lishing that the vehicle complies with Directive 72/245/EEC or with
the following alternative standards:
— Broadband electromagnetic radiation: CISPR 12 or SAE J551-2,
— Narrowband electromagnetic radiation: CISPR 12 (off-board) or 25

(in-board) or SAE J551-4 and SAE J1113-41.
Immunity tests
Immunity test shall be waived.
11 Directive 72/306/EEC (a) A test shall be conducted in accordance with the methods described
in Annex III and IV to Directive 72/306/EEC.
(Diesel smoke)
The limit values applicable are those mentioned in Annex V to that
Directive.
(b) The corrected value of the absorption coefficient referred to in

Section 4 of Annex I to Directive 72/306/EEC shall be affixed
12 Directive 74/60/EEC Interior arrangement
(Interior fittings) (a) With respect to the requirements on energy absorption, the vehicle
shall be deemed to comply with Directive 74/60/EEC if the vehicle
is fitted with at least two front airbags, one inserted into the steering
wheel and the other into the dashboard.
(b) Where the vehicle is fitted with only one front air bag inserted in
the steering wheel, the dashboard shall be made up of energy
absorbing materials.
(c) The technical service shall check that there are no sharp edges in
the zones defined in Sections 5.1 to 5.7 of Annex I to Directive 74/
60/EEC.
02007L0046 — EN — 18.01.2018 — 021.001 — 193
▼M10
Electrical controls
(a) Power-operated windows, roof–panel systems and partitioning

systems shall be tested in accordance with Section 5.8 of
Annex I to that Directive.
The sensitivity of auto-reverse systems referred to in point 5.8.3 of

that Annex may diverge from the requirements set out in
point 5.8.3.1.1.
(b) Electric windows which cannot be closed when the ignition is off
shall be exempt from the requirements concerning auto-reverse
systems.
13 Directive 74/61/EEC (a) In order to prevent unauthorised use, the vehicle shall be fitted with:
(Anti-theft and immobiliser) — a locking device as defined in Section 2.2 of Annex IV to

Directive 74/61/EEC, and
— an immobiliser which meets the technical requirements of

Section 3 of Annex V to that Directive and the essential
requirements of Section 4, in particular point 4.1.1.
(b) If, in application of point (a) above, an immobiliser has to be retro

fitted it shall be of an approved type in accordance with Directive
74/61/EEC or UNECE Regulation No 97 or No 116.
14 Directive 74/297/EEC (d) (a) The applicant shall submit a statement from the manufacturer estab
lishing that the particular vehicle, [the VIN number of which has to
(Protective steering) be specified], complies with at least one of the following:
— Directive 74/297/EEC,
— FMVSS No 203 (Impact protection for the driver from the

steering control system) including FMVSS No 204 (Steering
control rearward displacement),
— Article 11 of JSRRV.
(b) A test in accordance with Annex II to Directive 74/297/EEC may

be conducted on a production vehicle at the request of the applicant.
The test shall be conducted by a notified European technical service

which has competence therein. A detailed report shall be issued to
the applicant.
15 Directive 74/408/EEC Seats, seat anchorages and adjustment systems
(Seat strength — head The applicant shall submit a statement from the manufacturer estab
restraints) lishing that the particular vehicle, [the VIN number of which has to
be specified], complies with at least one of the following:
— FMVSS No 207 (Seating systems).

02007L0046 — EN — 18.01.2018 — 021.001 — 194
▼M10
Head restraints
(a) Where the statement referred to above is based on FMVSS No 207,

the head restraints shall fulfil in addition the essential requirements
of Section 3 of Annex II to Directive 74/408/EEC and those of
Section 5 of Appendix I to the same Annex.
(b) Only the tests described in point 3.10 and Sections 5, 6 and 7 of
Annex II to that Directive shall be conducted.
(c) In the other event, the applicant shall submit a statement from the
manufacturer establishing that the particular vehicle, [the VIN
number of which has to be specified], complies with FMVSS
No 202a (Head restraints).
16 Directive 74/483/EEC (a) The external surface of the bodywork shall comply with the general
requirements included in Section 5 of Annex I to Directive 74/483/
(Exterior projections) EEC.
(b) At the discretion of the technical service the provisions referred to

in points 6.1, 6.5, 6.6, 6.7, 6.8 and 6.11 of Annex I to that Directive
shall be checked.
17 Directive 75/443/EEC Speedometer equipment
(Speedometer — reverse (a) The dial shall comply with points 4.1 to 4.2.3 of Annex II to
gear) Directive 75/443/EEC.
(b) Where the technical service has reasonable grounds to believe that
the speedometer is not calibrated with sufficient accuracy, it may
require that the tests prescribed in Section 4.3 be conducted.
Reverse gear
The gear mechanism shall include a reverse gear.
18 Directive 76/114/EEC Vehicle identification number
(Statutory plates) (a) The vehicle shall be fitted with a vehicle identification number
comprising a minimum of 8 and a maximum of 17 characters.
Vehicle identification number comprising 17 characters shall fulfil
the requirements set out in Standards ISO 3779:1983 and
3780:1983.
(b) The vehicle identification number shall be located in a clearly

visible and accessible position in such a way as it cannot be oblit
erated or deteriorate.
(c) Where no vehicle identification number is stamped in the chassis or

in the body, a Member State may require that it is retrofitted in
application of its national law. In such a case, the competent
authority of that Member State shall supervise the operation.
Statutory plate
The vehicle shall be fitted with an identification plate affixed by the

vehicle manufacturer.
No additional plate shall be requested after the approval has been

granted.
02007L0046 — EN — 18.01.2018 — 021.001 — 195
▼M10
19 Directive 76/115/EEC The applicant shall submit a statement from the manufacturer estab
(Seat belt anchorages) be specified], complies with at least one of the following:
— FMVSS No 210 (Seat belt assembly anchorages),
— Article 22-3 of JSRRV.
20 Directive 76/756/EEC (a) The lighting installation shall meet the essential requirements of
UNECE Regulation No 48 series of amendments 03 with the
(Installation of lighting and exception of those of Annexes 5 and 6 to Regulation 48.
light signalling devices)
(b) No exemption shall be permitted in respect of the number, the
essential design characteristics, the electrical connections, and the
colour of light emitted or retro-reflected of the lights and signalling
devices referred to in Entries 21 to 26 and in Entries 28 to 30.
(c) Lights and signalling devices which in application of the above

must be retrofitted shall bear an ‘EC’ type-approval mark.
(d) Lamps fitted with gas-discharged light source are only permitted in
conjunction with the installation of headlamp cleaning device and
an automatic headlamp-levelling device where appropriate.
(e) Headlamp dipped-beams shall be adapted to the direction of traffic

legally in force in the country where the vehicle is granted approval.
21 Directive 76/757/EEC Where necessary, two additional retro reflectors bearing an ‘EC’
approval mark shall be added at the rear, the position of which shall
(Retro reflectors) comply with UNECE Regulation No 48.
22 Directive 76/758/EEC The requirements set out in that Directive shall not apply. However, the
correct functioning of the lights shall be checked by the technical
(End-outline, front position service.
(side), rear-position (side),
stop, side marker, daytime
running lamps)
(Direction indicators) service.
(Rear registration plate service.
lamps)
25 Directive 76/761/EEC (a) The illumination produced by the passing beam of the headlamps
fitted to the vehicle shall be checked under Section 6 of UNECE
(Headlamps Regulation No 112 concerning headlamps emitting an asymmetrical
(including bulbs)) passing beam. The tolerances included in Annex 5 to that Regu
lation may be referred to for that purpose.
(b) The same decision shall apply mutatis mutandis to the passing beam
of headlamps covered by UNECE Regulation No 98 or No 123.
02007L0046 — EN — 18.01.2018 — 021.001 — 196
▼M10
correct functioning of the lights if fitted shall be checked by the
(Front fog lamps) technical service.
27 Directive 77/389/EEC The requirements set out in that Directive shall not apply.
(Towing hooks)
(Rear fog lamps) service.
(Reversing lamps) technical service.
(Parking lamps) technical service.
(Seat belts and restraint (a) Seat belts shall not be required to be type-approved in accordance
systems) with Directive 77/541/EEC.
(b) However, each seat belt shall bear an identification label.
(c) The indications on the label shall be consistent with the decision
concerning seat belt anchorages (Re: entry 19).
Installation requirements
(a) The vehicle shall be fitted with seat belts in accordance with the
requirements set out in Annex XV to Directive 77/541/EEC.
(b) Where a number of seat belts have to be retrofitted in accordance

with point (a) above, they shall be of an approved type in
accordance with Directive 77/541/EEC or UNECE Regulation
No 16.
32 Directive 77/649/EEC (a) No obstruction in the 180° forward field of vision of the driver as
defined in point 5.1.3 of Annex I to Directive 77/649/EEC shall be
(Forward vision) permitted.
(b) By derogation from point (a) above, the ‘A pillars’ and the
equipment listed in point 5.1.3 of Annex I to that Directive shall
not be considered as obstruction.
(c) The number of ‘A pillars’ shall not exceed 2.
33 Directive 78/316/EEC (a) The symbols including the colour of their corresponding tell-tales
the presence of which is mandatory by virtue of Annex II to
(Identification of controls, Directive 78/316/EEC shall comply with that Directive.
tell-tales and indicators)
(b) Where this is not the case, the technical service shall verify that the
symbols, tell-tales and indicators fitted to the vehicle provide the
driver with comprehensible information about the operation of the
controls in question.
02007L0046 — EN — 18.01.2018 — 021.001 — 197
▼M10
34 Directive 78/317/EEC The vehicle shall be equipped with adequate windscreen defrosting and
windscreen demisting devices.
(Defrost/Demist)
Shall be deemed ‘adequate’ any windscreen defrosting device which
complies as a minimum with point 5.1.1 of Annex I to Directive
78/317/EEC.
Shall be deemed ‘adequate’ any windscreen demisting device which

complies as a minimum with point 5.2.1 of Annex I to that Directive.
35 Directive 78/318/EEC The vehicle shall be equipped with adequate windscreen washing and
windscreen wiping devices.
(Wash/Wipe)
Shall be deemed ‘adequate’ any windscreen washing and wiping device
which complies as a minimum with the conditions set out in point 5.1.3
of Annex I to Directive 78/318/EEC.
36 Directive 2001/56/EC (a) The passenger compartment shall be fitted with a heating system.
(Heating systems) (b) Combustion heaters and their installation shall comply with
Annex VII to Directive 2001/56/EC. In addition, LPG combustion
heaters and LPG heating systems shall fulfil the requirements set
out in Annex VIII to that Directive.
(c) Additional heating systems which are retrofitted shall comply with
the requirements set out in that Directive.
37 Directive 78/549/EEC (a) The vehicle shall be designed as to protect other road users against
thrown-up stones, mud, ice, snow and water and to reduce the
(Wheel guards) dangers due to contact with the moving wheels.
(b) The technical service may check that the essential technical
requirements set out in Annex I to Directive 78/549/EEC are
complied with.
(c) The provisions of Section 3 of Annex I to that Directive shall not

apply.
38 Directive 78/932/EEC The requirements of Directive 78/932/EEC shall not apply.
(Head restraints)
39 Directive 80/1268/EEC (a) A test shall be conducted in accordance with Section 5 of Annex I
(CO2 emissions/fuel con
sumption) (b) The requirements set out in point 5.1.1 of that Annex shall not
apply.
(c) Where no test concerning tailpipe emissions is conducted in appli

cation of the provisions referred to in Entry 2, CO2 emissions and
fuel consumption shall be calculated with the formula laid down in
the explanatory notes (b) and (c).
▼M20
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 198
▼M10
41 Directive 2005/55/EC Tailpipe emissions
(Emissions (Euro 4 and 5) (a) A test shall be conducted in accordance with Section 6.2 of Annex I
heavy duty vehicles — to Directive 2005/55/EC using the deterioration factors set out in
OBDs — Smoke opacity) point 3.6 of Annex II to Directive 2005/78/EC.
(b) The limits shall be those set out in Table I or Table 2 in Annex I to
Directive 2005/55/EC.
OBD

Smoke opacity

accordance with the tests methods referred to in Annex VI to

▼M20

2009
(a) A test shall be conducted in accordance with Annex III to
Emissions (Euro VI) Regulation (EU) No 582/2011 using the deterioration factors set
heavy-duty vehicles – OBD out in point 3.6.1. of Annex VI to Regulation (EU) No 582/2011.
(b) The limits to be applied shall be those set out in the table of
Annex I to Regulation (EC) No 595/2009.
prescribed in Annex IX to Regulation (EU) No 582/2011.
CO2 emissions
The CO2 emissions and fuel consumption shall be determined in

accordance with Annex VIII to Regulation (EU) No 582/2011.
OBD
(b) The OBD-interface must be able to communicate with an external

OBD scan-tool as described in Annex X to Regulation (EU)
No 582/2011.
Requirements to ensure the correct operation of NOx control measures
The vehicle shall be fitted with a system ensuring the correct operation
of NOx control measures in accordance with Annex XIII to
Regulation (EU) No 582/2011. The provisions on alternative
type-approval set out in point 2.1. of that Annex shall also apply.
Power measurement
(a) The applicant shall submit a statement from the manufacturer

stating the maximum engine power output in kW as well as the
corresponding engine speed in revolutions per minute.
alternatively referred to.
02007L0046 — EN — 18.01.2018 — 021.001 — 199
▼M10
44 Directive 92/21/EEC (a) The requirements of Section 3 of Annex II to Directive 92/21/EEC

shall be fulfilled.
(Masses and dimensions)
(b) For the application of the provisions referred to in point (a), the
masses to be considered are:
— the mass in running order defined in point 2.6 of Annex I to

Directive 2007/46/EC as measured by the technical service, and
— the laden masses either stated by the vehicle manufacturer or

shown on the manufacturer’s plate including stickers or
information available in the owner’s manual. Those masses
shall be deemed the technically permissible maximum laden
masses.
(c) No exemption shall be permitted in respect of the maximum

permissible dimensions.
(Safety glazing) (a) The glazing shall be made either of tempered or laminated safety
glass.
(b) Fitting of plastic glazing shall be permitted only on locations

situated behind the ‘B’ pillar.
(c) Glazing shall not be required to be approved under Directive

92/22/EEC.
Installation
(a) The installation prescriptions set out in Annex 21 to UNECE Regu

lation No 43 shall apply.
(b) No tinted films which would reduce the regular light transmission
under the required minimum shall be permitted on the windscreen
and on the glazing located in front of the ‘B’ pillar.
(Tyres) Tyres shall bear an ‘EC’ type-approval mark including the symbol ‘s’
(for sound).
Installation
(a) The dimensions, load-capacity index and speed category of the tyres
shall fulfil the requirements of Annex IV to Directive 92/23/EEC.
(b) The speed category symbol of the tyre shall be compatible with the
maximum design speed of the vehicle.
The presence of a speed limiter shall not exempt from the appli
cation of this requirement.
(c) For the application of the provisions of point (b) above, the
maximum speed of the vehicle shall be stated by the vehicle manu
facturer. However, the technical service may assess the maximum
design speed of the vehicle by using the engine maximum power
output, the maximum number of revolutions per minute and the
data concerning the kinematic chain.
02007L0046 — EN — 18.01.2018 — 021.001 — 200
▼M10
50 Directive 94/20/EC Separate technical units
(Couplings) (a) OEM couplings intended for towing a trailer whose maximum mass
does not exceed 1 500 kg shall not be required to be type-approved
under Directive 94/20/EC.
A coupling is deemed OEM equipment where it is described in the

owner’s manual or an equivalent supporting document provided to
the buyer by the vehicle manufacturer.
Where such coupling is approved with the vehicle, an appropriate

text shall be included in the approval certificate stating that the
owner is responsible for ensuring compatibility with the coupling
device fitted to the trailer.
(b) Couplings other than those referred to in point (a) above as well as
couplings that are retrofitted shall be type-approved in accordance
with Directive 94/20/EC.
Installation on the vehicle
The technical service shall check that the installation of the coupling
devices comply with Annex VII to Directive 94/20/EC.
53 Directive 96/79/EC (a) The applicant shall submit a statement from the manufacturer estab
(Frontal impact) (e) be specified] complies with at least one of the following:
— Directive 96/79/EC,
— FMVSS No 208 (Occupant crash protection),
(b) A test in accordance with Annex II to Directive 96/79/EC may be

conducted on a production vehicle at the request of the applicant.

the applicant.
(Side impact) be specified] complies with at least one of the following:
— FMVSS No 214 (Side impact protection),
(b) A test in accordance with Section 3 of Annex II to Directive 96/27/

EC may be conducted on a production vehicle at the request of the
applicant.

the applicant.
02007L0046 — EN — 18.01.2018 — 021.001 — 201
▼M10
58 Regulation (EC) No 78/ Brake assist

2009
Vehicles shall be fitted with an electronic antilock braking system
(Pedestrian protection) acting on all wheels.
Pedestrian protection
The requirements of that Regulation shall not apply until 1 January

2013.
Frontal protection systems
However, frontal protection systems installed on the vehicle shall be

type-approved in accordance with Regulation (EC) No 78/2009 and
their installation shall comply with the essential requirements set out
in Section 6 of Annex I to that Regulation.
59 Directive 2005/64/EC The requirements of that Directive shall not apply.
(Recyclability)
61 Directive 2006/40/EC The requirements of that Directive shall apply.
(Air-conditioning system)
Part II: Vehicles belonging to category N1
1 Directive 70/157/EEC Drive-by test
(Permissible sound level) (a) A test shall be conducted in accordance with the ‘Method A’
referred to in Annex 3 to UNECE Regulation No 51.
Limits are those specified in Section 2.1 of Annex I to Directive

70/157/EEC. 1 decibel in addition to the permitted limits shall be
allowed.
(b) The test track shall comply with Annex 8 to UNECE Regulation
No 51. A test track having different specifications may be used
under the condition that correlation tests have been conducted by
the technical service. A correction factor shall be applied if
necessary.
(c) Exhaust systems containing fibrous materials need not be condi

tioned as prescribed in Annex 5 to UNECE Regulation No 51.
Stationary test
A test shall be conducted in accordance with Section 3.2 of Annex 3 to

2 Directive 70/220/EEC Tailpipe emissions
(Emissions) (a) A type I test shall be conducted in accordance with Annex III to
Directive 70/220/EEC using the deterioration factors referred to in
point 5.3.6.2. The limits to be applied shall be those specified in
point 5.3.1.4 of Annex I to that Directive.

in Section 3.1.1 of Annex III to that Directive.
02007L0046 — EN — 18.01.2018 — 021.001 — 202
▼M10
prescribed in Annex IX to Directive 70/220/EEC.

requirements of Section 3.2 of Appendix 2 to Annex III to that
Directive.
(e) The test referred to in point (a) shall not be conducted when it can
be demonstrated that the vehicle complies with one of the California
Regulations mentioned in the prefatory note to Section 5 of Annex I
to that Directive.
Vehicles equipped with a petrol-fuelled engine shall be fitted with an

evaporate emissions control system (e.g. a charcoal canister).
Crankcase emissions

required.
OBD

▼M20

2007
(a) A type I test shall be conducted in accordance with Annex III to
(Emissions Euro 5 and 6 Regulation (EC) No 692/2008 using the deterioration factors set out
light duty vehicles/access in point 1.4 of Annex VII to Regulation (EC) No 692/2008. The
to information) limits to be applied shall be those specified in Table I and Table II
in Annex I to Regulation (EC) No 715/2007.
(b) The vehicle shall not be required to exhibit 3 000 km as mentioned

prescribed in Annex IX to Regulation (EC) No 692/2008.

requirements set out in Section 3.2 of Annex 4 to UNECE Regu
lation No 83.
be shown that the vehicle complies with the California Regulations
referred to in Section 2 of Annex I to Regulation (EC) No 692/
2008.
For petrol-fuelled engines, the presence of an evaporate emissions

control system shall be required (e.g. a charcoal canister).
Crankcase emissions

required.
02007L0046 — EN — 18.01.2018 — 021.001 — 203
▼M20
OBD

Smoke opacity

accordance with the tests methods referred to in Appendix 2 to
Annex IV to Regulation (EC) No 692/2008.

CO2 emissions and fuel consumption
(a) A test shall be conducted in accordance with Annex XII to


(c) Where the vehicle complies with the California Regulations referred
to in Section 2 of Annex I to Regulation (EC) No 692/2008 and
therefore no test of tailpipe emissions is required to be performed,
Member States shall calculate CO2 emissions and fuel consumption
with the formulae laid down in the explanatory notes (b) and (c).
Access to information
The provisions regarding access to information shall not apply.
Power measurement
(a) The applicant shall submit a statement from the manufacturer stating
the maximum engine power output in kW as well as the corre
sponding regime in revolutions per minute.
alternatively be referred to.
▼M10
3 Directive 70/221/EEC Fuel tanks
(Fuel tanks — Rear (a) Fuel tanks shall comply with Section 5 of Annex I to Directive
protective devices) 70/221/EEC with the exception of points 5.1, 5.2 and 5.12. In
particular they shall comply with points 5.9 and 5.9.1 but no
dripping test shall be conducted.
(b) LPG or CNG tanks shall be type-approved in accordance with,

respectively UNECE Regulations 67 series of amendments 01 or
Regulation No 110 (a).
Specific provisions for fuel tanks made of a plastic material

lishing that the fuel tank on the particular vehicle, [the VIN number
of which has to be specified], complies either with at least one of the
following:
— Section 6.3 of Directive 70/221/EEC,

02007L0046 — EN — 18.01.2018 — 021.001 — 204
▼M10
— FMVSS No 301 (Fuel system integrity),
— Annex 5 to UNECE Regulation 34.
Rear protective device
(a) The rear part of the vehicle shall be constructed in accordance with
section 5 of Annex II to Directive 70/221/EEC.
(b) For such purposes, it is sufficient that the requirements set out in
the second subparagraph of point 5.2 are fulfilled.
(c) If, in application of the above, a rear protection device has to be

retrofitted, it shall comply with points 5.3 and 5.4 of Annex II to
that Directive.
4 Directive 70/222/EEC Space, inclination, angles for visibility and position of the registration
plate shall comply with Directive 70/222/EEC.
(Rear registration plate
space)
5 Directive 70/311/EEC Mechanical systems
(Steering effort) (a) The steering mechanism shall be built as to self-centre. In order to
check compliance with this provision, a test shall be conducted in
accordance with points 5.1.2 and 5.2.1 of Annex I to Directive
70/311/EEC.
(b) The failure of the power steering equipment shall not lead to a
complete loss of control of the vehicle.
Complex electronic vehicle control system (‘Drive-by wire’ devices)
Complex electronic control system shall be permitted only if they

comply with Annex 6 to UNECE Regulation No 79.
6 Directive 70/387/EEC (a) Door latches and hinges shall comply with points 3.2.1, 3.3.2 and
3.4.1 of Annex I to Directive 70/387/EEC.
(Door latches and hinges)
(b) The requirements set out in point 3.4.1 shall not apply where
compliance with point 6.1.5.4 of UNECE Regulation No 11
Rev.1 Amendment 2 is demonstrated.
(Audible warning) The audible warning devices are not required to be type-approved in
accordance with Directive 70/388/EEC. However, they shall emit a
continuous sound as required in point 1.1 of Annex I to Directive
70/388/EEC.
(a) A test shall be conducted in accordance with Section 2 of Annex I

(b) The maximum sound pressure level shall be in accordance with

point 2.1.4 of that Annex.
8 Directive 2003/97/EC Components
(Indirect vision devices) (a) The vehicle shall be fitted with the rear-view mirrors prescribed in
Section 2 of Annex III to Directive 2003/97/EC.
02007L0046 — EN — 18.01.2018 — 021.001 — 205
▼M10
(b) They are not required to be type-approved in accordance with that

Directive.
(c) The radii of curvature of the mirrors shall not cause significant
image distortions. At the discretion of the technical service, the
radii of curvature shall be checked in accordance with the method
described in Appendix 1 to Annex II to Directive 2003/97/EC. The
radii of curvature shall not be less than those required by Section
3.4 of Annex II to that Directive.
Measurement shall be conducted in order to ensure that the fields of

vision comply with either the provisions of Section 5 of Annex III to
Directive 2003/97/EC or with Section 5 of Annex III to Directive
71/127/EEC.
9 Directive 71/320/EEC General provisions
(Braking) (a) The braking system shall be built in accordance with Section 2 of
Annex I to Directive 71/320/EEC.
(b) Vehicles shall be fitted with an electronic antilock braking system

acting on all wheels.
(c) The performances of the braking system shall comply with Section
2 of Annex II to that Directive.
(d) For these purposes, road tests shall be conducted on a track the
surface of which possesses high adhesion. The test on the parking
brake shall be conducted on a 18 % gradient (up and down).
Only those tests mentioned below shall be conducted. In each case,

the vehicle shall be in fully laden conditions.
(e) The road test referred to in point (c) above shall not be conducted
where the applicant can submit a statement from the manufacturer
establishing that the vehicle complies either with UNECE Regu
lation No 13-H including supplement 5 or with FMVSS No 135.
Service brake
(a) A ‘Type 0’ test as prescribed in points 1.2.2 and 1.2.3 of Annex II

to Directive 71/320/EEC shall be conducted.
(b) In addition, a ‘Type I’ test as prescribed in point 1.3 of Annex II to

that Directive shall be conducted.
Parking brake
A test shall be conducted in accordance with point 2.1.3 of Annex II to

that Directive.
(Radio interference (elec (a) Electrical/electronic sub-assemblies are not required to be

tromagnetic compatibility)) type-approved in accordance with Directive 72/245/EEC.
(b) However, electric/electronic devices retrofitted shall comply with

that Directive.
02007L0046 — EN — 18.01.2018 — 021.001 — 206
▼M10
Emitted electromagnetic radiations

lishing that the vehicle complies with Directive 72/245/EEC or with
the following alternative standards:
— Broadband electromagnetic radiation: CISPR 12 or SAE J551-2,
— Narrowband electromagnetic radiation: CISPR 12 (off-board) or 25

(in-board) or SAE J551-4 and SAE J1113-41.
Immunity tests
Immunity test shall be waived.
11 Directive 72/306/EEC (a) A test shall be conducted in accordance with the methods described
in Annexes III and IV to Directive 72/306/EEC.
(Diesel smoke)
The limit values applicable are those mentioned in Annex V to that
Directive.
(b) The corrected value of the absorption coefficient referred to in

Section 4 of Annex I to Directive 72/306/EEC shall be affixed
13 Directive 74/61/EEC (a) In order to prevent unauthorised use, the vehicle shall be fitted with
a locking device as defined in Section 2.2 of Annex IV to Directive
(Anti-theft and immobiliser) 74/61/EEC.
(b) If an immobiliser is fitted it shall comply with the technical

requirements of Section 3 of Annex V to that Directive and the
essential requirements set out in Section 4, in particular point 4.1.1.
14 Directive 74/297/EEC (f) (a) The applicant shall submit a statement from the manufacturer estab
(Protective steering) be specified], complies with at least one of the following:
— FMVSS No 203 (Impact protection for the driver from the

steering control system) including FMVSS No 204 (Steering
control rearward displacement),
(b) A test in accordance with Annex II to Directive 74/297/EEC may be

conducted on a production vehicle at the request of the applicant.
the applicant.
15 Directive 74/408/EEC Seats, seat anchorages and adjustment systems
Seats strength — head Seats and their adjustable systems shall comply with Annex IV to
restraints Directive 74/408/EEC.
Head restraints
(a) Head restraints shall fulfil the essential requirements of Section 3 of

Annex II to Directive 74/408/EEC and Section 5 of Appendix I to
that Annex.
02007L0046 — EN — 18.01.2018 — 021.001 — 207
▼M10
(b) Only the tests described in point 3.10 and Sections 5, 6 and 7 of
Annex II to that Directive shall be conducted.
17 Directive 75/443/EEC Speedometer equipment
(Speedometer — reverse (a) The dial shall comply with points 4.1 to 4.2.3 of Annex II to
gear) Directive 75/443/EEC.
(b) When the technical service has reasonable grounds to believe that
the speedometer is not calibrated with a sufficient accuracy, it may
require that the tests prescribed in Section 4.3 be conducted.
Reverse gear
The gear mechanism shall include a reverse gear.
18 Directive 76/114/EEC Vehicle identification number
(Statutory plates) (a) The vehicle shall be fitted with a vehicle identification number
comprising a minimum of 8 and a maximum of 17 characters.
Vehicle identification number comprising 17 characters shall fulfil
the requirements set out in Standards ISO 3779:1983 and
3780:1983.
(b) The vehicle identification number shall be located in a clearly

visible and accessible position in such a way as it cannot be oblit
erated or deteriorate.
(c) Where no vehicle identification number is stamped in the chassis or

in the body, a Member State may require that it is retrofitted in
application of its national law. In such a case, the competent
authority of that Member State shall supervise the operation.
Statutory plate
The vehicle shall be fitted with an identification plate affixed by the

vehicle manufacturer.
No additional plate shall be requested after the approval has been

granted.
19 Directive 76/115/EEC The applicant shall submit a statement from the manufacturer estab
(Seat belt anchorages) be specified], complies with at least one of the following:
— FMVSS No 210 (Seat belt assembly anchorages),
— Article 22-3 of JSRRV.
20 Directive 76/756/EEC (a) The lighting installation shall meet the essential requirements of
UNECE Regulation No 48 series of amendments 03 with the
(Installation of lighting and exception of those of Annexes 5 and 6 to Regulation 48.
light signalling devices)
(b) No exemption shall be permitted in respect of the number, the
essential design characteristics, the electrical connections, and the
colour of light emitted or retro-reflected of the lights and signalling
devices referred to in Entries 21 to 26 and in Entries 28 to 30.
02007L0046 — EN — 18.01.2018 — 021.001 — 208
▼M10
(c) Lights and signalling devices which in application of the above

must be retrofitted shall bear an ‘EC’ type-approval mark.
(d) Lamps fitted with gas-discharged light source are only permitted in
conjunction with the installation of headlamp cleaning device and
an automatic headlamp-levelling device where appropriate.
(e) Headlamp dipped-beams shall be adapted to the direction of traffic

legally in force in the country where the vehicle is granted approval.
21 Directive 76/757/EEC Where necessary, two additional retro reflectors bearing an ‘EC’
approval mark shall be added at the rear, the position of which shall
(Retro reflectors) comply with UNECE Regulation No 48.
(End-outline, front position service.
(side), rear-position (side),
stop, side marker, daytime
running lamps)
(Direction indicators) service.
(Rear registration plate service.
lamps)
25 Directive 76/761/EEC (a) The illumination produced by the passing beam of the headlamps
fitted to the vehicle shall be checked under the provisions of Section
(Headlamps 6 of UNECE Regulation No 112 concerning headlamps emitting an
(including bulbs)) asymmetrical passing beam. The tolerances included in Annex 5 to
that Regulation may be referred to for that purpose.
(b) The same decision shall apply mutatis mutandis to the passing beam
of headlamps covered by UNECE Regulation No 98 or 123.
26 Directive 76/762/EEC The provisions of that Directive shall be waived. However, the correct
functioning of the lights if fitted shall be checked by the technical
(Front fog lamps) service.
27 Directive 77/389/EEC The requirements of that Directive shall be waived.
(Towing hooks)
functioning of the lights shall be checked by the technical service.
(Rear fog lamps)
(Reversing lamps) service.
(Parking lamps) service.
02007L0046 — EN — 18.01.2018 — 021.001 — 209
▼M10
(Seat belts and restraint (a) Seat belts shall not be required to be type-approved in accordance
systems) with Directive 77/541/EEC.
(b) However, each seat belt shall bear an identification label.
(c) The indications on the label shall be consistent with the decision
concerning seat belt anchorages (Re: entry 19).
Installation requirements
(a) The vehicle shall be fitted with seat belts in accordance with the
requirements set out in Annex XV to Directive 77/541/EEC.
(b) Where a number of seat belts have to be retrofitted in accordance

with point (a) above, they shall be of an approved type in
accordance with Directive 77/541/EEC or UNECE Regulation
No 16.
33 Directive 78/316/EEC (a) The symbols including the colour of their corresponding tell-tales
the presence of which is mandatory by virtue of Annex II to
(Identification of controls, Directive 78/316/EEC shall comply with that Directive.
tell-tales and indicators)
(b) Where this is not the case, the technical service shall verify that the
symbols, tell-tales and indicators fitted to the vehicle provide the
driver with comprehensible information about the operation of the
controls in question.
34 Directive 78/317/EEC The vehicle shall be equipped with adequate windscreen defrosting and
windscreen demisting devices.
Defrost/Demist
35 Directive 78/318/EEC The vehicle shall be equipped with adequate windscreen washing and
windscreen wiping devices.
Wash/Wipe
36 Directive 2001/56/EC (a) The passenger compartment shall be fitted with a heating system.
(Heating systems) (b) Combustion heaters and their installation shall comply with
Annex VII to Directive 2001/56/EC. In addition, LPG combustion
heaters and LPG heating systems shall fulfil the requirements set out
in Annex VIII to that Directive.
(c) Additional heating systems which are retrofitted shall comply with
the requirements set out in that Directive.
39 Directive 80/1268/EEC (a) A test shall be conducted in accordance with Section 5 of Annex I
(CO2 emissions/fuel cons
umption) (b) The requirements set out in point 5.1.1 of that Annex shall not
apply.
(c) Where no test concerning tailpipe emissions is conducted in appli

cation of the provisions referred to in Entry 2, CO2 emissions and
fuel consumption shall be calculated with the formula laid down in
the explanatory notes (b) and (c).
▼M20
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 210
▼M10
41 Directive 2005/55/EC Tailpipe emissions
(Emissions (Euro 4 and 5) (a) A test shall be conducted in accordance with Section 6.2 of Annex I
heavy duty vehicles — to Directive 2005/55/EC using the deterioration factors set out in
OBDs — Smoke opacity) point 3.6 of Annex II to Directive 2005/78/EC.
(b) The limits shall be those set out in Table I or Table 2 in Annex I to
OBD

Smoke opacity

accordance with the tests methods referred to in Annex VI to

▼M20

2009
(a) A test shall be conducted in accordance with Annex III to
Emissions (Euro VI) Regulation (EU) No 582/2011 using the deterioration factors set
heavy-duty vehicles – OBD out in point 3.6.1. of Annex VI to Regulation (EU) No 582/2011.
(b) The limits to be applied shall be those set out in the table of
Annex I to Regulation (EC) No 595/2009.
prescribed in Annex IX to Regulation (EU) No 582/2011.
CO2 emissions
The CO2 emissions and fuel consumption shall be determined in

accordance with Annex VIII to Regulation (EU) No 582/2011.
OBD
(b) The OBD-interface must be able to communicate with an external

OBD scan-tool as described in Annex X to Regulation (EU)
No 582/2011.
Requirements to ensure the correct operation of NOx control measures
The vehicle shall be fitted with a system ensuring the correct operation
of NOx control measures in accordance with Annex XIII to
Regulation (EU) No 582/2011. The provisions on alternative
type-approval set out in point 2.1. of that Annex shall also apply.
Power measurement
(a) The applicant shall submit a statement from the manufacturer stating
the maximum engine power output in Kw as well as the corre
sponding regime
alternatively referred to.
02007L0046 — EN — 18.01.2018 — 021.001 — 211
▼M10
(Safety glazing) (a) The glazing shall be made either of tempered or laminated safety
glass.
(b) Fitting of plastic glazing shall be permitted only on locations

situated behind the ‘B’ pillar.
(c) Glazing shall not be required to be approved under Directive

92/22/EEC.
Installation
(a) The installation prescriptions set out in Annex 21 to UNECE Regu

lation No 43 shall apply.
(b) No tinted films which would reduce the regular light transmission
under the required minimum shall be permitted on the windscreen
and on the glazing located in front of the ‘B’ pillar.
(Tyres) Tyres shall bear an ‘EC’ type-approval mark including the symbol ‘s’
(for sound).
Installation
(a) The dimensions, load-capacity index and speed category of the tyres
shall fulfil the requirements of Annex IV to Directive 92/23/EEC.
(b) The speed category symbol of the tyre shall be compatible with the
maximum design speed of the vehicle.
(c) The presence of a speed limiter shall not exempt from the appli
cation of this requirement.
(d) For the application of the provisions of point (b) above, the
maximum speed of the vehicle shall be stated by the vehicle manu
facturer. However, the technical service may assess the maximum
design speed of the vehicle by using the engine maximum power
output, the maximum number of revolutions per minute and the data
concerning the kinematic chain.
48 Directive 97/27/EC (a) The essential requirements of Annex I to Directive 97/27/EC shall
be fulfilled.
(Masses and dimensions)
However, the requirements set out in points 7.8.3, 7.9 and 7.10 of
that Annex shall not apply.
(b) For the application of the provisions of point (a) above, the masses
to be considered are:
— the mass in running order as defined in point 2.6 of Annex I to

Directive 2007/46/EC as measured by the technical service, and
— the maximum laden masses either stated by the vehicle manu

facturer or shown on the manufacturer’s plate including stickers
or information available in the owner’s manual. Those masses
shall be regarded as the technically permissible maximum laden
masses.
02007L0046 — EN — 18.01.2018 — 021.001 — 212
▼M10
(c) Technical changes made by the applicant — such as replacing tyres

with tyres with a lower load-capacity index — in order to decrease
the maximum technically permissible laden mass of the vehicle to
3,5 tonnes or less in order that the vehicle may be granted indi
vidual approval shall not be permitted.
(d) No exemption shall be permitted in respect of the maximum

permissible dimensions.
49 Directive 92/114/EEC (a) In accordance with Section 6 of Annex I to Directive 92/114/EEC,

the general requirements set out in Section 5 of Annex I to
(External projections of Directive 74/483/EEC shall be fulfilled.
cabs)
(b) At the discretion of the technical service the requirements set out in
points 6.1, 6.5, 6.6, 6.7, 6.8 and 6.11 of Annex I to Directive 74/
483/EEC shall be fulfilled.
50 Directive 94/20/EC Separate technical units
(Couplings) (a) OEM couplings intended for towing a trailer whose maximum mass
does not exceed 1 500 kg shall not be required to be type-approved
under Directive 94/20/EC.
(b) A coupling is deemed OEM equipment where it is described in the

owner’s manual or an equivalent supporting document provided to
the buyer by the vehicle manufacturer.
(c) Where such coupling is approved with the vehicle, an appropriate

text shall be included in the approval certificate stating that the
owner is responsible for ensuring compatibility with the coupling
device fitted to the trailer.
(d) Couplings other than those referred to in point (a) above as well as
couplings that are retrofitted shall be type-approved in accordance
Installation on the vehicle
The technical service shall check that the installation of the coupling
devices comply with Annex VII to Directive 94/20/EC.
(Side impact) be specified] complies with at least one of the following:
— FMVSS No 214 (Side impact protection),
(b) A test in accordance with Section 3 of Annex II to Directive 96/27/

EC may be conducted on a production vehicle at the request of the
applicant.
(c) The test shall be conducted by a notified European technical service

which has competence thereof. A detailed report shall be issued to
the applicant.
02007L0046 — EN — 18.01.2018 — 021.001 — 213
▼M10
56 Directive 98/91/EC Vehicles intended for the transport of dangerous goods shall comply
Vehicles intended for the
transport of dangerous
goods
58 Regulation (EC) No 78/ Brake assist

2009
Vehicles shall be fitted with an electronic antilock braking system
(Pedestrian protection) acting on all wheels.
Pedestrian protection
Until 24 February 2018, the requirements of that Regulation shall not

apply to vehicles whose maximum mass does not exceed 2 500 kg and
until 24 August 2019 to vehicles whose maximum mass exceeds
2 500 kg.
Frontal protection systems
However, frontal protection systems installed on the vehicle shall be

type-approved in accordance with Regulation (EC) No 78/2009 and
their installation shall comply with the essential requirements set out
in Section 6 of Annex I to that Regulation.
59 Directive 2005/64/EC The requirements of that Directive shall not apply.
(Recyclability)
61 Directive 2006/40/EC The requirements of that Directive shall apply.
(Air-conditioning system)
Explanatory notes relating to Appendix 2
1. Abbreviations used in this Appendix:
‘OEM’: original equipment provided by the manufacturer
‘FMVSS’: Federal Motor Vehicle Safety Standard of the U.S Department of Transportation
‘JSRRV’: Japan Safety regulations for Road Vehicles
‘SAE’: Society of Automotive Engineers
‘CISPR’: Comité international spécial des perturbations radioélectriques.
2. Remarks:
(a) the complete LPG or CNG installation shall be checked against the provisions of UNECE Regulations No 67 or 110 or 115
as appropriate;
(b) the formula to be used for the assessment of CO2 emissions shall be as follows:
Petrol engine and manual gearbox:
CO2 = 0,047 m + 0,561 p + 56,621
Petrol engine and automatic gearbox:
CO2 = 0,102 m + 0,328 p + 9,481
Petrol engine and hybrid electric:
CO2 = 0,116 m – 57,147

02007L0046 — EN — 18.01.2018 — 021.001 — 214
▼M10
Diesel engine and manual gearbox:
CO2 = 0,108 m – 11,371
Diesel engine and automatic gearbox:
CO2 = 0,116 m – 6,432
Where: CO2 is the combined mass of CO2 emissions in g/km, ‘m’ is the mass of the vehicle in running order in kg and ‘p’
the maximum engine power output in kW.
Combined mass of CO2 shall be calculated with 1 decimal place, then rounded to the nearest whole number as follows:
(a) if the figure following the decimal point is below 5, the total is rounded down;
(b) if the figure following the decimal point is equal to 5 or above 5, the total is rounded up;
(c) the formulæ to be used for the assessment of fuel consumption shall be as follows:
CFC = CO2 × k-1
Where: CFC is the combined fuel consumption in l/100 km, CO2 is the combined mass of CO2 emissions in g/km after it
has been rounded in accordance with the rule referred to in Remark (2 b), ‘k’ a coefficient equal to:
23,81 in the case of a petrol engine;
26,49 in the case of a diesel engine.
Combined fuel consumption shall be calculated with 2 decimal places. Then rounded as follows:
(a) if the figure following the first decimal is below 5, the total is rounded down;
(b) if the figure following the first decimal is equal to 5 or above 5, the total is rounded up;
(d) Directive 74/297/EEC applies to vehicles which are not covered by the scope of Directive 96/79/EC;
(e) Compliance with Directive 96/79/EC exempts vehicles from compliance with Directive 74/297/EEC;
(f) Directive 74/297/EEC applies to N1 vehicles with a technically permissible maximum laden mass not exceeding 1,5 tonnes.
02007L0046 — EN — 18.01.2018 — 021.001 — 215
▼M1
PART II
List of UNECE regulations recognised as an alternative to directives or

regulations mentioned in Part I
Where reference is made to a separate Directive or Regulation in the table of Part
I, an approval issued under the following UNECE Regulations to which the
Community has acceded as a Contracting Party to the United Nations
Economic Commission for Europe ‘Revised 1958 Agreement’ by virtue of
Council Decision 97/836/EC (1), or subsequent Council decisions as referred to
in Article 3(3) of that Decision, shall be considered as equivalent to an EC
type-approval granted under the relevant separate Directive or Regulation.
Any further amendment of the UNECE Regulations listed below (2) shall also be
deemed to be equivalent, subject to the Community Decision as referred to in
Article 4(2) of Decision 97/836/EC.
Basic UNECE Series of

Subject
Regulation number amendments
1 (*) Permissible sound level 51 02
Replacement silencing systems 59 00
▼M22
_____
58 Pedestrian protection 127 00
Braking (brake assist) 13-H 00 (Supplement

9 and above)
▼M1
Where the separate directive or regulation contains installation requirements, these apply also
to components and separate technical units approved in accordance with the UNECE Regu
lations.
(*) The numbering of the entries in this table refers to the numbering used in the table of
Part I.
(1) OJ L 346, 17.12.1997, p. 78.

(2) For subsequent amendments, see UNECE TRANS/WP.29/343 in its latest revision.
02007L0046 — EN — 18.01.2018 — 021.001 — 216
▼M9
ANNEX V
PROCEDURES TO BE FOLLOWED WITH RESPECT TO EC

TYPE-APPROVAL
0. Objectives and scope

0.1. This Annex establishes the procedures for the proper operation of the
vehicle type-approval in accordance with the provisions of Article 9.
0.2. It also includes:
(a) the list of international standards which are of relevance for the desig
nation of the technical services in accordance with Article 41;
(b) the description of the procedure to be followed for the assessment of

the skills of technical services in accordance with Article 42;
(c) the general requirements for the drafting of test reports by technical
services.
1. Type-approval process
When receiving an application for vehicle type-approval, the approval
authority shall:
(a) verify that all EC type-approval certificates issued pursuant to the

regulatory acts which are applicable for vehicle type-approval cover
the vehicle type and correspond to the prescribed requirements;
(b) by reference to the documentation make sure that the vehicle specifi
cations and data contained in Part I of the vehicle information
document are included in the data in the information packages and
in the EC type-approval certificates in respect of the relevant regulatory
acts;
(c) when an item number in Part I of the information document is not

included in the information package of any of the regulatory acts,
confirm that the relevant part or characteristic conforms to the
particulars in the information folder;
(d) on a selected sample of vehicles from the type to be approved carry out
or arrange to be carried out inspections of vehicle parts and systems to
verify that the vehicle(s) is/are built in accordance with the relevant
data contained in the authenticated information package in respect of
the relevant EC type-approval certificates;
(e) carry out or arrange to be carried out relevant installation checks in

respect of separate technical units where applicable;
(f) carry out or arrange to be carried out necessary checks in respect of the
presence of the devices provided for in footnotes (1) and (2) of Part I
of Annex IV where applicable;
(g) carry out or arrange to be carried out necessary checks in order to

ensure that the requirements provided for in footnote (5) of Part I of
Annex IV are fulfilled.
2. Combination of technical specifications

The number of vehicles to be submitted shall be sufficient to permit the
proper check of the various combinations to be type-approved according to
the following criteria:
Vehicle category
Technical specifications
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
Engine X X X X X X — — — —
Gear box X X X X X X — — — —
02007L0046 — EN — 18.01.2018 — 021.001 — 217
▼M9
Vehicle category
Technical specifications
M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
Number of axles — X X X X X X X X X
Powered axles (number, position and X X X X X X — — — —

interconnection)
Steered axles (number and position) X X X X X X X X X X
Body styles X X X X X X X X X X
Number of doors X X X X X X X X X X
Hand of drive X X X X X X — — — —
Number of seats X X X X X X — — — —
Level of equipment X X X X X X — — — —
3. Specific provisions
Where no approval certificates for any of the relevant regulatory acts are
available, the approval authority shall:
(a) arrange for the necessary tests and checks as required by each of the
relevant regulatory acts;
(b) verify that the vehicle conforms to the particulars in the vehicle
information folder and that it meets the technical requirements of
each of the relevant regulatory acts;
(c) carry out or arrange to be carried out relevant installation checks in
respect of separate technical units where applicable;
(d) carry out or arrange to be carried out necessary checks in respect of the
presence of the devices provided for in footnotes (1) and (2) of Part I
of Annex IV where applicable;
(e) carry out or arrange to be carried out necessary checks in order to
ensure that the requirements provided for in footnote (5) of Part I of
Annex IV are fulfilled.
02007L0046 — EN — 18.01.2018 — 021.001 — 218
▼M9
Appendix 1
Standards with which the entities referred to in Article 41 have to comply
1. Activities related to testing for type-approval, to be carried out in

accordance with the regulatory acts listed in Annex IV:
1.1. Category A (tests performed in own facilities):
EN ISO/IEC 17025:2005 on the general requirements for the competence
of testing and calibration laboratories.
A technical service designated for category A activities may carry out or
supervise the tests provided for in the regulatory acts for which it has been
designated, in the facilities of a manufacturer or of a third party.
1.2. Category B (supervising of tests performed in the manufacturer’s facilities
or in the facilities of a third party):
EN ISO/IEC 17020:2004 on the general criteria for the operation of various
types of bodies performing inspection.
Before performing or supervising any test in the facilities of a manufacturer
or of a third party, the technical service shall check that the tests facilities
and measurement devices comply with the appropriate requirements of the
standard referred to in point 1.1.
2. Activities related to Conformity of Production
2.1. Category C (procedure for the Initial Assessment and surveillance audits of
the manufacturer’s quality management system):
EN ISO/IEC 17021:2006 on the requirements for bodies providing audit
and certification of management systems.
2.2. Category D (inspection or testing of production samples or supervision
thereof):
EN ISO/IEC 17020:2004 on the general criteria for the operation of various
types of bodies performing inspection.
02007L0046 — EN — 18.01.2018 — 021.001 — 219
▼M9
Appendix 2
Procedure for the assessment of the technical services
1. Purpose of this Appendix

1.1. This Appendix establishes the conditions according to which the
assessment procedure of the technical services shall be conducted by
the competent authority referred to in Article 42.
1.2. These requirements shall apply mutatis mutandis to all technical services,
irrespective of their legal status (independent organisation, manufacturer
or approval authority acting as technical service).
2. Principles of assessing
Assessing shall be characterised by reliance on a number of principles:
— independence which is the basis for the impartiality and objectivity of

the conclusions,
— an evidence-based approach which guarantees reliable and repro

ducible conclusions.
Auditors shall show trust and integrity. They shall respect confidentiality
and discretion.
They shall report truthfully and accurately findings and conclusions.
3. Skills required of the auditors

3.1. The assessments may only be conducted by auditors having the technical
and administrative knowledge necessary for such purposes.
3.2. The auditors shall have been trained specifically for assessment activities.
In addition, they shall have the specific knowledge of the technical area in
which the technical service will exercise its activities.
3.3. Without prejudice to points 3.1 and 3.2 of this Appendix, the assessment
referred to in Article 42 shall be conducted by auditors independent of the
activities for which the assessment is conducted.
4. Application for designation

4.1. A duly authorised representative of the applicant technical service shall
make a formal application to the competent authority that includes the
following:
(a) general features of the technical service, including corporate entity,

name, addresses, legal status and technical resources;
(b) a detailed description including curriculum vitae of the personnel in

charge of testing and of the managerial staff as evidenced by the
skills both educational and professional;
(c) in addition to the above, technical services which use virtual testing
methods shall provide evidence of their ability to work in
a Computer-Aided-x environment;
(d) general information concerning the technical service such as its

activities, its relationship in a larger corporate entity if any, and
addresses of all its physical location(s) to be covered by the scope
of designation;
(e) an agreement to fulfil the requirements for designation and the other
obligations of the technical service as applicable in the relevant
Directives;
02007L0046 — EN — 18.01.2018 — 021.001 — 220
▼M9
(f) a description of the conformity assessment services that the technical
service undertakes in the framework of the applicable regulatory acts
and a list of the regulatory acts for which the technical service applies
for designation, including limits of capability where applicable;
(g) a copy of the quality manual of the technical service.
4.2. The competent authority shall review for adequacy the information
supplied by the technical service.
5. Resource review
The competent authority shall review its ability to carry out the
assessment of the technical service, in terms of its own policy, its
competence and the availability of suitable auditors and experts.
6. Subcontracting the assessment

6.1. The competent authority may subcontract parts of the assessment to
another designation authority or ask for support from technical experts
provided by other competent authorities. The subcontractors and experts
have to be accepted by the applicant technical service.
6.2. The competent authority shall take into account accreditation certificates
with adequate scope in order to complete its global assessment of the
technical service.
7. Preparation for assessment

7.1. The competent authority shall formally appoint an assessment team. The
former shall ensure that the expertise brought to each assignment is
appropriate. In particular, the team as a whole:
(a) shall have appropriate knowledge of the specific scope for which
designation is sought; and
(b) shall have understanding sufficient to make a reliable assessment of

the competence of the technical service to operate within its scope of
designation.
7.2. The competent authority shall clearly define the assignment given to the
assessment team. The task of the assessment team is to review the
documents collected from the applicant technical service and to conduct
the on-site assessment.
7.3. The competent authority shall agree, together with the technical service
and the assigned assessment team, to the date and schedule for the
assessment. However, it remains the responsibility of the competent
authority to pursue a date that is in accordance with the surveillance
and reassessment plan.
7.4. The competent authority shall ensure that the assessment team is provided
with the appropriate criteria documents, previous assessment records, and
the relevant documents and records of the technical service.
8. On-site assessment
The assessment team shall conduct the assessment of the technical service
at the premises of the technical service from which one or more key
activities are performed and, where relevant, shall perform witnessing at
other selected locations where the technical service operates.
9. Analysis of findings and assessment report

9.1. The assessment team shall analyse all relevant information and evidence
gathered during the document and record review and the on-site
assessment. This analysis shall be sufficient to allow the team to
determine the extent of competence and conformity of the technical
service with the requirements for designation.
02007L0046 — EN — 18.01.2018 — 021.001 — 221
▼M9
9.2. The competent authority’s reporting procedures shall ensure that the
following requirements are fulfilled.
9.2.1. A meeting shall take place between the assessment team and the technical
service prior to leaving the site. At this meeting, the assessment team
shall provide a written and/or oral report on its findings obtained from the
analysis. An opportunity shall be provided for the technical service to ask
questions about the findings, including non-conformities, if any, and their
basis.
9.2.2. A written report on the outcome of the assessment shall be promptly

brought to the attention of the technical service. This assessment report
shall contain comments on competence and conformity, and shall identify
non-conformities, if any, to be resolved in order to conform to all of the
requirements for designation.
9.2.3. The technical service shall be invited to respond to the assessment report
and to describe the specific actions taken or planned to be taken, within a
defined time, to resolve any identified non-conformities.
9.3. The competent authority shall ensure that the responses of the technical
service to resolve non-conformities are reviewed to see if the actions
appear to be sufficient and effective. If the technical service responses
are found not to be sufficient, further information shall be requested.
Additionally, evidence of effective implementation of actions taken may
be requested, or a follow-up assessment may be carried out to verify
effective implementation of corrective actions.
9.4. The assessment report shall include, as a minimum the following:
(a) unique identification of the technical service;
(b) date(s) of the on-site assessment;
(c) name(s) of the auditors(s) and/or experts involved in the assessment;
(d) unique identification of all premises assessed;
(e) proposed scope of designation that was assessed;
(f) a statement on the adequacy of the internal organisation and

procedures adopted by the technical service to give confidence in
its competence, as determined through its fulfilment of the
requirements for designation;
(g) information on the resolution of all non-conformities;
(h) a recommendation of whether the applicant should be designated or

confirmed as technical service and, if so, the scope of designation.
10. Granting/confirming a designation

10.1. The approval authority shall, without undue delay, make the decision on
whether to grant, confirm or extend designation on the basis of the
report(s) and any other relevant information.
10.2. The approval authority shall provide a certificate to the technical service.
This certificate shall identify the following:
(a) the identity and logo of the approval authority;
(b) the unique identity of the designated technical service;
(c) the effective date of granting of designation and the expiry date;
(d) a brief indication of or a reference to the scope of designation

(applicable directives, regulations or part of them);
(e) a statement of conformity and a reference to the present Directive.

02007L0046 — EN — 18.01.2018 — 021.001 — 222
▼M9
11. Reassessment and surveillance
11.1. Reassessment is similar to an initial assessment except that experience
gained during previous assessments shall be taken into account.
Surveillance on-site assessments are less comprehensive than
reassessments.
11.2. The competent authority shall design its plan for reassessment and
surveillance of each designated technical service so that representative
samples of the scope of designation are assessed on a regular basis.
The interval between on-site assessments, whether reassessment or
surveillance, depends on the proven stability that the technical service
has reached.
11.3. When, during surveillance or reassessments, non-conformities are
identified, the competent authority shall define strict time limits for
corrective actions to be implemented.
11.4. When the corrective or improvement actions have not been taken within
the agreed timeframe or are not deemed to be sufficient, the competent
authority shall adopt appropriate measures, such as conducting a further
assessment or suspending/withdrawing the designation for one or more of
the activities for which the technical service has been designated.
11.5. When the competent authority decides to suspend or withdraw the desig
nation of a technical service, it shall inform the latter by registered mail.
In any case, the competent authority shall adopt all the necessary
measures to ensure the continuity of the activities already undertaken
by the technical service.
12. Records on designated technical services
12.1. The competent authority shall maintain records on technical services to
demonstrate that requirements for designation, including competence,
have been effectively fulfilled.
12.2. The competent authority shall keep the records on technical services
secure to ensure confidentiality.
12.3. Records on technical services shall include at least the following:
(a) relevant correspondence;
(b) assessment records and reports;
(c) copies of designation certificates.
02007L0046 — EN — 18.01.2018 — 021.001 — 223
▼M9
Appendix 3
General requirements concerning the format of the test reports
1. For each of the regulatory acts listed in Part I of Annex IV, the test report
shall comply with the provisions of Standard EN ISO/IEC 17025:2005. In
particular it shall include the information mentioned in point 5.10.2, including
footnote (1) of that Standard.
2. The template of the test reports shall be laid down by the approval authority
in accordance with its rules of good practice.
3. The test report shall be drafted in the official language of the Community
determined by the approval authority.
4. Moreover it shall include at least the following information:
(a) the identification of the vehicle, component or separate technical unit
tested;
(b) a detailed description of the vehicle, component or separate technical unit
characteristics in connection with the regulatory act;
(c) the results of the measurements specified in the relevant regulatory acts
and, when required, the limits or thresholds which are to be met;
(d) in regard to each measurement mentioned in point 4(c) the relevant
decision: passed or failed;
(e) a detailed statement of compliance with the various provisions which are
to be met, i.e. such provisions for which it is not required to make
measurements.
Example from Section 3.2.2 of Annex I to Council Directive
76/114/EEC (1):
‘Check that the vehicle identification number is placed in such a way that
it cannot be obliterated or deteriorate’;
the report shall include a statement such as: ‘the place of stamping the
vehicle identification number fulfils the requirements of Section 3.2.2 of
Annex I’;
(f) when test methods other than those prescribed in the regulatory acts are
permitted the report shall include a description of the test method used
for performing the test.
The same applies when alternative provisions in the regulatory acts may
be used;
(g) pictures taken during testing, the number of which shall be decided by
the approval authority.
In the case of virtual testing, screen prints or other suitable evidence may
replace pictures;
(h) conclusions drawn up;
(i) when opinions and interpretations have been made, they shall be docu
mented properly and marked as such in the test report.
5. When the tests are conducted on a vehicle, component or technical unit that
combines a number of most unfavourable features with regard to the required
level of performance to be achieved (i.e. the worst-case), the test report shall
include a reference stating how the selection has been made by the manu
facturer in agreement with the approval authority.
(1) OJ L 24, 30.1.1976, p. 1.

02007L0046 — EN — 18.01.2018 — 021.001 — 224
▼M1
ANNEX VI
MODELS OF THE TYPE-APPROVAL CERTIFICATE
MODEL A
(to be used for type-approval of a vehicle)

Maximum format: A4 (210 × 297 mm)
EC VEHICLE TYPE-APPROVAL CERTIFICATE
Stamp of type-approval authority
Communication concerning: Of a type of:
— EC type-approval (1) — complete vehicle (1)

— extension of EC type-approval (1) — completed vehicle (1)
— refusal of EC type-approval (1) — incomplete vehicle (1)
— withdrawal of EC type-approval (1) — vehicle with complete and
incomplete variants (1)
— vehicle with completed and
incomplete variants (1)
with regard to Directive 2007/46/EC as last amended by Directive …./…/EC /
Regulation (EC) No. …/… (1)
EC type-approval number:
Reason for extension:
SECTION I
0.1. Make (trade name of manufacturer):
0.2. Type:
0.2.1. Commercial name(s) (2):
0.3. Means of identification of type, if marked on the vehicle:
0.3.1. Location of that marking:
0.4. Category of vehicle (3):
▼M24
0.5. Company name and address of manufacturer of the complete/completed
vehicle (1):
(1) Delete where not applicable.

(2) If not available at the time of granting the type-approval, this item shall be completed at
the latest when the vehicle is introduced on the market.
(3) As defined in Annex II.A.
02007L0046 — EN — 18.01.2018 — 021.001 — 225
▼M24
0.5.1. For multi-stage approved vehicles, company name and address of the
manufacturer of the base/previous stage(s) vehicle . . . . . . . . . . . . . . . . . . . . .
▼M1
0.8. Name(s) and address(es) of assembly plant(s):
SECTION II
The undersigned hereby certifies the accuracy of the manufacturer's description in
the attached information document of the vehicle(s) described above ((a)
sample(s) having been selected by the EC type-approval authority and
submitted by the manufacturer as prototype(s) of the vehicle type) and that the
attached test results are applicable to the vehicle type.
1. For complete and completed vehicles/variants (1):
The vehicle type meets/does not meet (1) the technical requirements of all
the relevant regulatory acts as prescribed in Annex IV and
Annex XI (1) (2) to Directive 2007/46/EC.
2. For incomplete vehicles/variants (1):
The vehicle type meets/does not meet (1) the technical requirements of the
regulatory acts listed in the table on side 2.
3. The approval is granted/refused/withdrawn (1).
4. The approval is granted in accordance with Article 20 and the validity of

the approval is thus limited to dd/mm/yy.
(Place) (Signature) (Date)

Attachments: Information package.
Test results (see Annex VIII).
Name(s) and specimen(s) of the signature(s) of the person(s) auth

orised to sign certificates of conformity and a statement of their
position in the company.
NB: If this model is used for type-approval pursuant to Articles 20, 22 or 23, it
may not bear the heading ‘EC Vehicle Type-Approval Certificate’, except:
— in the case mentioned in Article 20 where the Commission has decided to

allow a Member State to grant a type-approval in accordance with this
Directive,
— in the case of vehicles of the category M1, type-approved according to the

procedure prescribed in Article 22.
02007L0046 — EN — 18.01.2018 — 021.001 — 226
▼M1
EC VEHICLE TYPE-APPROVAL CERTIFICATE
Side 2
This EC type-approval is, where incomplete and completed vehicles, variants or

versions are concerned, based on the approval(s) for incomplete vehicles listed
below:
Stage 1: Manufacturer of the base vehicle:
Dated:
Applicable to variants or versions (as appropriate):
Stage 2: Manufacturer:
Dated:
Stage 3: Manufacturer:
Dated:
In the case where the approval includes one or more incomplete variants or
versions (as appropriate), list those variants or versions (as appropriate) which
are complete or completed.
Complete/completed variant(s):
List of requirements applicable to the approved incomplete vehicle type, variant

or version (as appropriate, taking account of the scope and latest amendment to
each of the regulatory acts listed below).
Applicable to
Regulatory act variant or, if
Item Subject Last amended
reference need be, to
version
(List only subjects for which an EC type-approval exists.)
In the case of special purpose vehicles, exemptions granted or special provisions

applied pursuant to Annex XI and exemptions granted pursuant to Article 20:
Applicable to variant
Regulatory act Kind of approval and
Item number or, if need be, to
reference nature of exemption
version
02007L0046 — EN — 18.01.2018 — 021.001 — 227
▼M24
Appendix
List of regulatory acts to which the type of vehicle complies
(to be filled in only in the case of type-approval in accordance with Article 6(3)).
Regulatory act
Subject (1) As amended by Applicable to variants
reference (1)
1. Permissible sound level
▼M23
1A. Sound Level Regulation (EU)

No 540/2014
▼M24
2. Emissions
3. Fuel tanks/Rear protective devices
(1) In accordance with Annex IV to this Directive

02007L0046 — EN — 18.01.2018 — 021.001 — 228
▼M10
MODEL B
(To be used for type-approval of a vehicle with regard to a system)

▼M1
EC TYPE-APPROVAL CERTIFICATE
Communication concerning:
9
— EC type-approval (1) >
>
>
>
=
of a type of system/type of a vehicle
— extension of EC type-approval (1)
>
> with regard to a system (1)
>
>
;
— refusal of EC type-approval (1)
— withdrawal of EC type-approval (1)

with regard to Directive …/…/EC / Regulation (EC) No …/… (1), as last
amended by Directive …/…/EC / Regulation (EC) No …/… (1)
SECTION I
0.2. Type:
0.2.1. Commercial name(s) (if available):
0.3. Means of identification of type, if marked on the vehicle (2):
0.4. Category of vehicle (3):
0.5. Name and address of manufacturer:
SECTION II
1. Additional information (where applicable): see Addendum.
2. Technical service responsible for carrying out the tests:
3. Date of test report:
4. Number of test report:
5. Remarks (if any): see Addendum.
6. Place:
7. Date:

(2) If the means of identification of type contains characters not relevant to describe the
‘?’ (e.g. ABC??123??).
(3) As defined in Annex II, Section A.
02007L0046 — EN — 18.01.2018 — 021.001 — 229
▼M1
8. Signature:
Attachments: Information package
Test report
02007L0046 — EN — 18.01.2018 — 021.001 — 230
▼M1
Addendum
to EC type-approval certificate No …
1. Additional information
1.1. […]:
1.1.1. […]:
[…]
2. Type-approval number of each component or separate technical unit
installed on the vehicle type to comply with this Directive or Regulation
2.1. […]:
3. Remarks
3.1. […]:
02007L0046 — EN — 18.01.2018 — 021.001 — 231
▼M1
MODEL C
(to be used for component/separate technical unit type-approval)

EC TYPE-APPROVAL CERTIFICATE
Communication concerning:
9
— EC type-approval (1) >
=
of a type of component/separate
; technical unit ( )
1
>
— extension of EC type-approval (1)
— refusal of EC type-approval (1)
— withdrawal of EC type-approval (1)

with regard to Directive …/…/EC / Regulation (EC) No …/… (1), as last
amended by Directive …/…/EC / Regulation (EC) No …/… (1)
SECTION I
0.2. Type:
0.3. Means of identification of type, if marked on the component/separate

technical unit (1) (2):
0.5. Name and address of manufacturer:
0.7. In the case of components and separate technical units, location and
method of affixing of the EC approval mark:
SECTION II
1. Additional information (where applicable): see Addendum
2. Technical service responsible for carrying out the tests:
3. Date of test report:
4. Number of test report:
5. Remarks (if any): see Addendum
6. Place:
7. Date:

(2) If the means of identification of type contains characters not relevant to describe the
‘?’ (e.g.. ABC??123??).
02007L0046 — EN — 18.01.2018 — 021.001 — 232
▼M1
8. Signature:
Attachments: Information package.
Test report.
02007L0046 — EN — 18.01.2018 — 021.001 — 233
▼M1
Addendum
to EC type-approval certificate No …
1. Additional information
1.1. […]:
1.1.1. […]:
[…]
2. Restriction of use of the device (if any)
2.1. […]:
3. Remarks
3.1. […]:
02007L0046 — EN — 18.01.2018 — 021.001 — 234
▼M10
MODEL D
(to be used for harmonised individual approval of a vehicle pursuant Article 24)
EC INDIVIDUAL VEHICLE APPROVAL CERTIFICATE
Name, address, phone number and e-mail-address of the individual approval

authority
Communication concerning individual vehicle approval with regard to Article 24 of Directive

2007/46/EC
Section 1
The undersigned [… …name and position] hereby certifies that the vehicle:
0.1. Make (trade name of manufacturer): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.2. Type: Variant: Version:
0.2.1. Commercial name: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.4. Category of vehicle (2): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.5. Name and address of the manufacturer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.6. Location and method of attachment of the statutory plates: … . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Location of the vehicle identification number: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0.10. Vehicle identification number:
submitted for approval on […… date of application]
by […… Name and address of the applicant]
is granted approval according to the provisions of Article 24 of Directive 2007/46/EC. In witness
whereof, the following approval number has been allocated: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The vehicle complies with Appendix 2 to Annex IV to Directive 2007/46/EC. It can be permanently
registered without further approval in Member States having right/left hand traffic (1) and using
metric/imperial (1) units for the speedometer.
(Place) (Date) (Signature (3)) (Stamp of the approval authority)
[…] […] […]
Attachments
Two photos (5) of the vehicle (min resolution 640 x 480 pixel, ~7 x 10 cm)

(2) As defined in Annex II.A
(3) Or visual representation of an ‘advanced electronic signature’ according to Directive 1999/93/EC, including
data for verification.
(4) Distinguishing number of the Member State issuing the individual approval: (see ‘Section 1’ in Point 1, of
Annex VII of Directive 2007/46/EC)
(5) One ¾ front, one ¾ rear
02007L0046 — EN — 18.01.2018 — 021.001 — 235
▼M10
Section 2
General construction characteristics

1. Number of axles: …. . . . . . . . . . . . . . . . . . . . . . . . . . . and wheels: … . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1. Number and position of axles with twin wheels: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. Powered axles (number, position, interconnection): …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main dimensions
4. Wheelbase (a): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm
4.1. Axle spacing: 1-2: … . . . . . . . . . . . . mm 2-3: … . . . . . . . . . . . . mm 3-4: … . . . . . . . . . . . . mm
5. Length: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm
6. Width: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm
7. Height: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . mm
Masses
13. Mass of the vehicle in running order: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg (b)
16. Technically permissible maximum masses
16.1. Technically permissible maximum laden mass: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg
16.2. Technically permissible mass on each axle: 1. … . . . . kg 2. … . . . . kg 3. … . . . . kg etc.
16.4. Technically permissible maximum mass of the combination: … . . . . . . . . . . . . . . . . . . . . . . . . kg
18. Technically permissible maximum towable mass in case of:
18.1. Drawbar trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg
18.2. Semi-trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg
18.3. Centre-axle trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg
18.4. Unbraked trailer: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kg
19. Technically permissible maximum static vertical mass at the coupling point: … . . . . . . . . kg
Power plant
20. Manufacturer of the engine: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21. Engine code as marked on the engine: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22. Working principle: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23. Pure electric: yes/no (1)
23.1. Hybrid [electric] vehicle: yes/no (1)
24. Number and arrangement of cylinders: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25. Engine capacity: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . cm3
26. Fuel: Diesel/petrol/LPG/NG – Biomethane/Ethanol/Biodiesel/Hydrogen (1)
26.1. Mono fuel/Bi fuel/Flex fuel (1)
27. Maximum net power (c): … kW at … min-1 or maximum continuous rated power (electric
motor) … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . kW (1)
Maximum speed
29. Maximum speed: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . km/h
02007L0046 — EN — 18.01.2018 — 021.001 — 236
▼M10
Axles and suspension
30. Axle(s) track: 1. …. . . . . . . . . . . . . . . mm 2. … . . . . . . . . . . . . . . mm 3. … . . . . . . . . . . . . . . mm
35. Tyre/wheel combination: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bodywork
38. Code for bodywork (d): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40. Colour of vehicle (e): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41. Number and configuration of doors: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42. Number of seating positions (including the driver) (f): … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
42.1. Seat(s) designated for use only when the vehicle is stationary: … . . . . . . . . . . . . . . . . . . . . . . . . .
42.3. Number of wheelchair user accessible position: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Coupling device
44. Approval number or approval mark of coupling device (if fitted): …. . . . . . . . . . . . . . . . . . . . . .
Environmental performances
46. Sound level
Stationary: … . . . . . . . . . . . . . . . . . . . . dB(A) at engine speed: … . . . . . . . . . . . . . . . . . . . . . min-1
Drive-by: …. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . dB(A)
47. Exhaust emission level (g): Euro … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other legislation: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49. CO2 emissions/fuel consumption/electric energy consumption (h):
1. all power train except pure electric vehicles
CO2 emissions Fuel consumption
Combined: … g/km … l/100 km/m3/100 km (1)

Weighted, combined … g/km … l/100 km
2. pure electric vehicles and OVC hybrid electric vehicles

Electric energy consumption (weighted, combined (1)) …. . . . . . . . . . . . . . . . . . . . . . . Wh/km
52. Remarks
53. Additional information (mileage (2), …)
Explanatory notes relating to Annex VI model D

(1) Delete where not applicable
(2) Not compulsory
(a) This entry shall be completed only where the vehicle has two axles.
(b) This mass is the actual mass of the vehicle in the conditions referred to in point 2.6 of Annex I.
(c) For hybrid electric vehicles, indicate both power outputs.
(d) The codes described in Section C of Annex II shall be used.
(e) Indicate only the basic colour(s): white, yellow, orange, red, violet, blue, green, grey, brown or black.
(f) Excluding seats designated for use only when the vehicle is stationary and the number of wheelchair positions.
(g) Add the number of the Euro level and, if appropriate, the character corresponding to the provisions used for
type-approval.
( ) Repeat for the various fuels which can be used.
h
02007L0046 — EN — 18.01.2018 — 021.001 — 237
▼M1
ANNEX VII
EC TYPE-APPROVAL CERTIFICATE NUMBERING SYSTEM (1)
1. The EC type-approval number shall consist of four sections for whole

vehicle type-approvals and five sections for system, component, and
separate technical unit type-approvals as detailed below. In all cases, the
sections shall be separated by the ‘*’ character.
Section 1: The lower case letter ‘e’ followed by the distinguishing number
of the Member State issuing the EC type-approval:
1 for Germany; 19 for Romania;

2 for France; 20 for Poland;
3 for Italy; 21 for Portugal;
4 for the Netherlands; 23 for Greece;
5 for Sweden; 24 for Ireland;
6 for Belgium; ►M19 25 for Croatia; ◄
7 for Hungary; 26 for Slovenia;
8 for the Czech Republic; 27 for Slovakia;
9 for Spain; 29 for Estonia;
11 for the United Kingdom; 32 for Latvia;
12 for Austria; 34 for Bulgaria;
13 for Luxembourg; 36 for Lithuania;
17 for Finland; 49 for Cyprus;
18 for Denmark; 50 for Malta.
Section 2: The number of the base directive or regulation.

▼M26
In case of EC type-approval for systems, components or
separate technical units covered by the implementing measures
of Regulation (EC) No 661/2009, the base Regulation reference
shall be the Regulation number (i.e. the implementing act)
adopted pursuant to Article 14(1)(a) to (e) of Regulation (EC)
No 661/2009.
▼M1
Section 3:
▼M26
The number of the latest amending Directive or Regulation,
including implementing acts applicable to the type-approval in
accordance with the following indents. However, in case such
amending Directive or Regulation or applicable implementing
act does not yet exist, the number referred to in Section 2 is
repeated in Section 3:
▼M1
— in the case of whole vehicle type-approvals, this means the
latest directive or regulation amending an Article (or
Articles) of Directive 2007/46/EC,
— in the case of whole vehicle type-approvals granted in

accordance with the procedure described in Article 22, this
means the latest directive or regulation amending an Article
(or Articles) of Directive 2007/46/EC, except that the two
first digits (e.g. 20) are replaced by the letters KS in block
capitals,
(1) Components and separate technical units shall be marked in accordance with the
provisions of the relevant regulatory acts.
02007L0046 — EN — 18.01.2018 — 021.001 — 238
▼M1
— this means the latest directive or regulation containing the
actual provisions with which the system, component or
technical unit conforms,
▼M26
— this means the latest Regulation, containing amendments to
implementing measures of Regulation (EC) No 661/2009,
with which a system, component or technical unit complies,
▼M1
— should a directive or regulation including their implementing
acts contain different technical prescriptions to be applied
from specific dates, Section 3 shall be followed with an
alphabetical character to clearly identify against which
technical prescriptions the approval was granted. When
different vehicle categories are concerned, the character
may also refer to a specific vehicle category.
Section 4: A four-digit sequential number (with leading zeros as

applicable) for EC Whole vehicle type-approvals, or four or
five digits for type-approval pursuant to a separate directive or
regulation to denote the base type-approval number. The
sequence shall start from 0001 for each base directive or
regulation.
Section 5: A two-digit sequential number (with leading zeros if applicable)
to denote the extension. The sequence shall start from 00 for
each base approval number.
2. In the case of a type-approval for a whole vehicle, Section 2 shall be
omitted.
However, in the case of a national type-approval granted for vehicles

produced in small series pursuant Article 23, Section 3 shall be replaced
by the letters NKS in block capitals
3. On the vehicle's statutory plate(s) only, Section 5 shall be omitted.
4. Layouts of the type-approval numbers
4.1. Example of a third type-approval (which as yet no extension) issued by

France
(a) to Directive 71/320/EEC:
e2*71/320*2002/2078*00003*00
(b) to Directive 2005/55/EC:
e2*2005/2055*2006/51 D*00003*00 — in the case of a directive or

regulation with different technical prescriptions (see section 3)
▼M26
(c) to Commission Regulation (EU) No 1008/2010 (1) (windscreen wiper
and washer systems)
e2*1008/2010*1008/2010*00003*00
(d) to Commission Regulation (EU) No 19/2011 (2) as amended by

Commission Regulation (EU) No 249/2012 (3) (statutory markings)
e2*19/2011*249/2012*0003*00
(1) Commission Regulation (EU) No 1008/2010 of 9 November 2010 concerning

type-approval requirements for windscreen wiper and washer systems of certain motor
vehicles and implementing Regulation (EC) No 661/2009 of the European Parliament
and of the Council concerning type-approval requirements for the general safety of motor
vehicles, their trailers and systems, components and separate technical units intended
therefor (OJ L 292, 10.11.2010, p. 2).
(2) Commission Regulation (EU) No 19/2011 of 11 January 2011 concerning type-approval
requirements for the manufacturer's statutory plate and for the vehicle identification
number of motor vehicles and their trailers and implementing Regulation (EC)
No 661/2009 of the European Parliament and of the Council concerning type-approval
requirements for the general safety of motor vehicles, their trailers and systems,
components and separate technical units intended therefor (OJ L 8, 12.1.2011, p. 1).
(3) Commission Regulation (EU) No 249/2012 of 21 March 2012 amending Regulation (EU)
No 19/2011 as regards type-approval requirements for the manufacturer's statutory plate
of motor vehicles and their trailers (OJ L 82, 22.3.2012, p. 1).
02007L0046 — EN — 18.01.2018 — 021.001 — 239
▼M1
4.2. Example of the second extension to the fourth vehicle type-approval issued
by the United Kingdom:
e11*2007/2046*0004*02
4.3. Example of a whole vehicle type-approval granted to a vehicle produced in
small series issued by Luxembourg, pursuant to Article 22:
e13*KS07/46*0001*00.
4.4. Example of a national type-approval granted to a vehicle produced in small
series issued by the Netherlands, pursuant to Article 23:
e4*NKS*0001*00.
4.5. Example of the type-approval number to be stamped on the vehicle's
statutory plate(s):
e11*2007/2046*0004.
▼M26
5. Annex VII does not apply to type-approvals granted in accordance with
UNECE Regulations listed in Annex IV, as the relevant numbering
system is provided for in the respective UNECE Regulations. However,
Annex VII applies to EC type-approvals granted under Regulation (EC)
No 661/2009 which are based on UNECE Regulations (i.e. incorporating
new technologies, EC type-approved components and STUs, virtual testing
and self-testing). In this case, the following numbering system is applied:
Section 1: as above
Section 2: ‘661/2009’ (i.e. General Safety Regulation)
Section 3: First portion is the UNECE Regulation No, followed by ‘R-’,
the second portion is the series of amendments or ‘00’ if it is the original
series, followed by ‘-’ and the third portion is the supplement level (with
leading zeroes if applicable) or ‘00’ when there is no supplement to the
relevant series.
Section 4: as above
Section 5: as above
Examples:
e1*661/2009*13-HR-10-05*00001*00
(granted by Germany, according to UNECE Regulation No 13-H, 10 series
of amendments, supplement level 5, first approval issued, no extensions)
e25*661/2009*28R-00-03*0123*05
(granted by Croatia, according to UNECE Regulation No 28, original series
of amendments, supplement 3, 123rd approval issued, 5th extension).
02007L0046 — EN — 18.01.2018 — 021.001 — 240
▼M1
Appendix
EC component and separate technical unit type-approval mark
1. The EC component and separate technical unit type-approval mark shall

consist of:
1.1. A rectangle surrounding the lower-case letter ‘e’ followed by the distin
guishing letter(s) or number of the Member State which has granted the
EC component or separate technical unit type-approval:
1 For Germany 19 For Romania
2 For France 20 For Poland
3 For Italy 21 For Portugal
4 For the Netherlands 23 For Greece
5 For Sweden 24 For Ireland
6 For Belgium ►M19 25 For Croatia ◄
7 For Hungary 26 For Slovenia
8 For the Czech Republic 27 For Slovakia
9 For Spain 29 For Estonia
11 For the United Kingdom 32 For Latvia
12 For Austria 34 For Bulgaria
13 For Luxembourg 36 For Lithuania
17 For Finland 49 For Cyprus
18 For Denmark 50 For Malta
1.2. In the vicinity of the rectangle the ‘base approval number’ contained in
Section 4 of the type-approval number preceded by the two figures indi
cating the sequence number assigned to the latest major technical
amendment to the relevant separate directive or regulation.
1.3. An additional symbol or symbols located above the rectangle, enabling

certain characteristics to be identified. This further information is specified
in the relevant separate directives or regulations.
2. The component or separate technical unit type-approval mark is affixed to

the separate technical unit or component in such a way as to be indelible
and clearly legible.
3. An example of a component or separate technical unit type-approval mark is

contained in the Addendum.
▼M26
4. This Appendix does not apply to type-approvals granted in accordance with
UNECE Regulations listed in Annex IV, as the relevant arrangements of
approval marks are provided for in the respective UNECE Regulations.
However, this Appendix applies to EC component and separate technical
unit type-approvals granted under Regulation (EC) No 661/2009 which are
based on UNECE Regulations (i.e. components or separate technical units
incorporating new technologies). In this case, the following arrangement of
markings is applied:
The distinguishing type-approval marking shall be as prescribed in the

relevant UNECE Regulation and as if granted through conventional
UNECE Regulation type-approval, however, the following shall be taken
into account:
02007L0046 — EN — 18.01.2018 — 021.001 — 241
▼M26
When a circle surrounding the letter ‘E’ is prescribed, this shall be not a
circle, but a rectangle. Its height (a) shall at least correspond to the
prescribed diameter size and its width shall exceed that value (i.e. > a).
Instead of the upper-case letter ‘E’, the lower-case letter ‘e’ shall be used,
followed by the distinguishing number of the Member State which has
granted the EC component or separate technical unit type-approval.
Example:
(granted by Germany, based on UNECE Regulation No 28, original series,

first approval issued, for a Class II audible warning device incorporating
new technologies)
02007L0046 — EN — 18.01.2018 — 021.001 — 242
▼M1
Addendum to appendix 1
Example of a component or separate technical unit type-approval mark
Legend: the above component type-approval was issued by Belgium under

number 0004. 01 is a sequential number denoting the level of technical
requirements to which this component fulfils. The sequential number is attributed
in accordance with the relevant separate directive or regulation.
NB: The additional symbols are not shown on this example.

02007L0046 — EN — 18.01.2018 — 021.001 — 243
▼M27
ANNEX VIII
TEST RESULTS
(To be completed by the type-approval authority and attached to the vehicle EC

type-approval certificate)
In each case, the information must make clear to which variant and version it is
applicable. One version may not have more than one result. However, a combi
nation of several results per version indicating the worst case is permissible. In
the latter case, a note shall state that for items marked (*) only worst case results
are given.
1. Results of the sound level tests

Number of the base regulatory act and latest amending regulatory act
applicable to the approval. In case of a regulatory act with two or more
implementation stages, indicate also the implementation stage: … . . . . . . .
Variant/Version: … … …
Moving (dB(A)/E): … … …
Stationary (dB(A)/E): … … …
at (min–1): … … …
2. Results of the exhaust emission tests

2.1. Emissions from motor vehicles tested under the test procedure for
light-duty vehicles
Indicate the latest amending regulatory act applicable to the approval. In
case the regulatory act has two or more implementation stages, indicate
also the implementation stage: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel(s) (1) … (diesel, petrol, LPG, NG, Bi-fuel: petrol/NG, LPG,

NG/biomethane, Flex-fuel: petrol/ethanol…)
2.1.1. Type 1 test (2), (3) (vehicle emissions in the test cycle after a cold start)
NEDC average values, WLTP highest values
CO (mg/km) … … …
THC (mg/km) … … …
NMHC (mg/km) … … …
(1) When restrictions for the fuel are applicable, indicate these restrictions (e.g. for natural
gas the L range or the H range).
(2) For bi fuel vehicles, the table shall be repeated for both fuels.
(3) For flex fuel vehicles, when the test is to be performed on both fuels, according to Figure
I.2.4 of Annex I to Regulation (EU) 2017/1151, and for vehicles running on LPG or
NG/Biomethane, either bi-fuel or mono-fuel, the table shall be repeated for the different
reference gases used in the test, and an additional table shall display the worst results
obtained. When applicable, in accordance with paragraph 3.1.4. of Annex 12 to UN/ECE
Regulation No 83, it shall be shown if the results are measured or calculated.
02007L0046 — EN — 18.01.2018 — 021.001 — 244
▼M27
NOx (mg/km) … … …
THC + NOx (mg/km) … … …
Mass of particulate matter (PM) … … …

(mg/km)
Number of particles (PN) … … …

(#/km) (1)
Ambient Temperature Correction Test (ATCT)
ATCT Family Interpolation family ►M29

_____ ◄
… … ►M29
_____ ◄
… … ►M29
_____ ◄
Family correction factors
ATCT Family FCF
… …
… …
2.1.2. Type 2 test (1), (2) (emissions data required at type-approval for roadwor
thiness purposes)
Type 2, low idle test:
CO (% vol.) … … …
Engine speed (min–1) … … …
Engine oil temperature (°C) … … …
Type 2, high idle test:
CO (% vol.) … … …
Lambda Value … … …
Engine oil temperature (°C) … … …
(1) For bi fuel vehicles, the table shall be repeated for both fuels.
(2) For flex fuel vehicles, when the test is to be performed on both fuels, according to Figure
I.2.4 of Annex I to Regulation (EU) 2017/1151, and for vehicles running on LPG or
NG/Biomethane, either bi-fuel or mono-fuel, the table shall be repeated for the different
reference gases used in the test, and an additional table shall display the worst results
obtained. When applicable, in accordance with paragraph 3.1.4. of Annex 12 to UN/ECE
Regulation No 83, it shall be shown if the results are measured or calculated.
02007L0046 — EN — 18.01.2018 — 021.001 — 245
▼M27
2.1.3. Type 3 test (emissions of crankcase gases): …
2.1.4. Type 4 test (evaporative emissions): … g/test
2.1.5. Type 5 test (durability of anti-pollution control devices):
— Ageing distance covered (km)(e.g. 160 000 km): …
— Deterioration factor DF: calculated/fixed (1)
— Values:
CO … … …
THC … … …
NMHC … … …
NOx … … …
THC + NOx … … …
Mass of particulate matter (PM) … … …
Number of particles (PN) (1) … … …
2.1.6. Type 6 test (average emissions at low ambient temperatures):
CO (g/km) … … …
THC (g/km) … … …
2.1.7. OBD: yes/no (2)
2.2. Emissions from engines tested under the test procedure for heavy-duty
vehicles.
also the implementation stage: …
Fuel(s) (3) … (diesel, petrol, LPG, NG, ethanol …)
2.2.1. Results of the ESC test (4), (5), (6)
CO (mg/kWh) … … …
THC (mg/kWh) … … …

(3) When restrictions for the fuel are applicable, indicate these restrictions (e.g. for natural
gas the L range or the H range).
(4) If applicable.
(5) For Euro VI, ESC shall be understood as WHSC and ETC as WHTC.
(6) For Euro VI, if CNG and LPG fuelled engines are tested on different reference fuels, the
table shall be reproduced for each reference fuel tested.
02007L0046 — EN — 18.01.2018 — 021.001 — 246
▼M27
NOx (mg/kWh) … … …
NH3 (ppm) (1) … … …
PM mass (mg/kWh) … … …
PM number (#/kWh) (1) … … …
2.2.2. Result of the ELR test (1)
Smoke value: … m–1 … … …
2.2.3. Result of the ETC test (2), (3)
CO (mg/kWh) … … …
THC (mg/kWh) … … …
NMHC (mg/kWh) (1) … … …
CH4 (mg/kWh) (1) … … …
NOx (mg/kWh) … … …
NH3 (ppm) (1) … … …
PM mass (mg/kWh) … … …
PM number (#/kWh) (1) … … …
2.2.4. Idle test (4)
CO (% vol.) … … …
Lambda Value (1) … … …
Engine oil temperature (K) … … …
2.3. Diesel smoke

also the implementation stage: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
(1) If applicable.
(2) For Euro VI, ESC shall be understood as WHSC and ETC as WHTC.
(3) For Euro VI, if CNG and LPG fuelled engines are tested on different reference fuels, the
table shall be reproduced for each reference fuel tested.
(4) If applicable.
02007L0046 — EN — 18.01.2018 — 021.001 — 247
▼M27
2.3.1. Results of the test under free acceleration
Corrected value of the absorption … … …

coefficient (m–1)
Normal engine idling speed … … …
Maximum engine speed … … …
Oil temperature (min./max.) … … …
3. Results of the CO2 emission, fuel/electric energy consumption, and

electric range tests
Number of the base regulatory act and the latest amending regulatory act
applicable to the approval: … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1. Internal combustion engines, including not externally chargeable hybrid

electric vehicles (NOVC) (1) (2)
CO2 mass emission (urban … … …

conditions) (g/km)
CO2 mass emission (extra-urban … … …

conditions) (g/km)
CO2 mass emission (combined) … … …

(g/km)
Fuel consumption (urban … … …

conditions) (l/100 km) (1)
Fuel consumption (extra-urban … … …

conditions) (l/100 km) (1)
Fuel consumption (combined) … … …

(l/100 km) (1)
(1) The unit ‘l/100 km’ is replaced by ‘m3/100 km’ for vehicles fuelled with NG
and H2NG, and by ‘kg/100 km’ for vehicles fuelled with hydrogen.
►M29
_____ ◄
Interpolation family identifier (1) Variant/versions
… …
… …
(1) If applicable.
(2) Repeat the table for each reference fuel tested.
02007L0046 — EN — 18.01.2018 — 021.001 — 248
▼M27
Interpolation family identifier (1) Variant/versions
… …
(1) The format for the Interpolation Family Identifier is provided in paragraph 5.0
of Annex XXI to Commission Regulation (EU) 2017/1151 of 1 June 2017
supplementing Regulation (EC) No 715/2007 of the European Parliament and
of the Council on type-approval of motor vehicles with respect to emissions
from light passenger and commercial vehicles (Euro 5 and Euro 6) and on
access to vehicle repair and maintenance information, amending Directive
2007/46/EC of the European Parliament and of the Council, Commission
Regulation (EC) No 692/2008 and Commission Regulation (EU) No 1230/
2012 and repealing Regulation (EC) No 692/2008 (OJ L 175, 7.7.2017, p. 1).
▼M29
__________
▼M27
Interpolation family identifier ►M29
___ ◄
Results:
VH
VM (if VL (if
►M29
___ ◄
applicable) applicable)
CO2 mass emission LOW phase … … …

(g/km)
CO2 mass emission MID phase … … …

(g/km)
CO2 mass emission HIGH phase … … …

(g/km)
CO2 mass emission EXTRA-HIGH … … …

phase (g/km)
CO2 mass emission (combined) … … …

(g/km)
Fuel consumption LOW phase … … …

(l/100 km m3/100 km kg/100 km)
Fuel consumption MID phase … … …

(l/100 km m3/100 km kg/100 km)
Fuel consumption HIGH phase … … …

(l/100 km m3/100 km kg/100 km)
Fuel consumption EXTRA-HIGH … … …

phase (l/100 km m3/100 km kg/
100 km)
Fuel consumption (combined) … … …

(l/100 km m3/100 km kg/100 km)
f0 … … …
02007L0046 — EN — 18.01.2018 — 021.001 — 249
▼M27

___ ◄
Results:
VH
VM (if VL (if
►M29
___ ◄
f1 … … …
f2 … … …
RR … … …
Delta Cd*A (for VL if applicable … … …

compared to VH)
Test Mass … … …
▼M29
Frontal area (m2) (for road load

matrix family vehicles only)
Repeat for each interpolation family.
▼M27
3.2. Externally chargeable hybrid electric vehicles (OVC) (1)
CO2 mass emission (Condition A, … … …

combined) (g/km)
CO2 mass emission (Condition B, … … …

combined) (g/km)
CO2 mass emission (weighted, … … …

combined) (g/km)
Fuel consumption (Condition A, … … …

combined) (l/100 km) (g)
Fuel consumption (Condition B, … … …

Fuel consumption (weighted, … … …

Electric energy consumption … … …

(Condition A, combined) (Wh/km)

(Condition B, combined) (Wh/km)
(1) If applicable.
02007L0046 — EN — 18.01.2018 — 021.001 — 250
▼M27

(weighted and combined) (Wh/
km)
Pure electric range (km) … … …
Interpolation family number Variant/versions
… …
… …
… …
▼M29
__________
▼M27
___ ◄
Results:
VH
VM (if VL (if
►M29
___ ◄
CS CO2 mass emission LOW … …

phase (g/km)
CS CO2 mass emission MID … …

phase (g/km)
CS CO2 mass emission HIGH … …

phase (g/km)
CS CO2 mass emission … …

EXTRA-HIGH phase (g/km)
CS CO2 mass emission … …

(combined) (g/km)
CD CO2 mass emission

(combined) (g/km)
CO2 mass emission (weighted,

combined) (g/km)
CS Fuel consumption LOW phase … …

(l/100 km)
CS Fuel consumption MID phase … …

(l/100 km)
02007L0046 — EN — 18.01.2018 — 021.001 — 251
▼M27

___ ◄
Results:
VH
VM (if VL (if
►M29
___ ◄
CS Fuel consumption HIGH … …

phase (l/100 km)
CS Fuel consumption … …
EXTRA-HIGH phase (l/100 km)
CS Fuel consumption (combined) … …

(l/100 km)
CD Fuel consumption (combined) … …

(l/100 km)
Fuel consumption (weighted, … …

combined) (l/100 km)
ECAC,weighted … …
EAER (combined) … …
EAERcity … …
f0 … …
f1 … …
f2 … …
RR … …
Delta Cd*A (for VL or VM … …

compared to VH)
Test Mass … …
▼M29
▼M27
Repeat for each interpolation family.
3.3. Pure electric vehicles (1)
Electric energy consumption (Wh/ … … …

km)
Range (km) … … …
(1) If applicable.
02007L0046 — EN — 18.01.2018 — 021.001 — 252
▼M27
Interpolation family number Variant/versions
… …
… …
… …
▼M29
__________
▼M27
Interpolation family
►M29
___ ◄
identifier
Results:
VH VL ►M29
___ ◄
Electric Consumption (Combined) … …

(Wh/km)
Pure Electric Range (Combined) … …

(km)
Pure Electric Range (City) (km) … …
f0 … …
f1 … …
f2 … …
RR … …
Delta Cd*A (for VL compared to … …

VH)
Test Mass … …
▼M29
▼M27
3.4. Hydrogen fuel cell vehicles (1)
Fuel consumption (kg/100 km) … … …
(1) If applicable.
02007L0046 — EN — 18.01.2018 — 021.001 — 253
▼M27
Variant/ Variant/
Version: Version:
Fuel Consumption (Combined) (kg/100 km) … …
f0 … …
f1 … …
f2 … …
RR … …
Test Mass …
▼M29
3.5. Output report(s) from the correlation tool in accordance with Imple
menting Regulation (EU) 2017/1151
Repeat for each interpolation family:
Interpolation family identifier [Footnote: ‘Type Approval Number + Inter

polation Family Sequence number’]: …
VH report: …
VL report (if applicable): …
3.5.1. Deviation factor (if applicable)


polation Family Sequence number’]: …
3.5.2. Verification factor (if applicable)


polation Family Sequence number’]: ….
▼M27
4. Results of the tests for vehicles fitted with eco-innovation(s) (1) (2) (3)
According to Regulation 83 (if applicable)
Variant/Version …
4. CO2 5. Usage
3. CO2 emissions of factor (UF)
2. CO2
Decision 1. CO2 emissions of the eco- i.e. temporal CO2
Type 1/I emissions of
approving Code of the emissions of the baseline innovation share of emissions
cycle the eco-
the eco- eco-inno the baseline vehicle vehicle technology savings
(NEDC/ innovation
inno vation (2) vehicle under under Type usage in ((1 – 2) –
WLTP) vehicle
vation (1) (g/km) Type 1 1 test-cycle normal (3 – 4)) * 5
(g/km)
test-cycle (3) (= 3.5.1.3 of operation
Annex I) conditions
xxx/201x … … … … … … … …
(1) (h1) Repeat the table for each variant/version.

(2) (h2) Repeat the table for each reference fuel tested
(3) (h3) Expand the table if necessary, using one extra row per eco-innovation.
02007L0046 — EN — 18.01.2018 — 021.001 — 254
▼M27
Variant/Version …
4. CO2 5. Usage
3. CO2 emissions of factor (UF)
2. CO2
Decision 1. CO2 emissions of the eco- i.e. temporal CO2
approving Code of the emissions of the baseline innovation share of emissions
cycle the eco-
the eco- eco-inno the baseline vehicle vehicle technology savings
(NEDC/ innovation
inno vation (2) vehicle under under Type usage in ((1 – 2) –
WLTP) vehicle
vation (1) (g/km) Type 1 1 test-cycle normal (3 – 4)) * 5
(g/km)
test-cycle (3) (= 3.5.1.3 of operation
Annex I) conditions
… … … … … … … … …
… … … … … … … … …
Total CO2 emissions savings on NEDC(g/km) (4) …
(1) (h4) Number of the Commission Decision approving the eco-innovation.

(2) (h5) Assigned in the Commission Decision approving the eco-innovation.
(3) (h6) If a modelling methodology is applied instead of the type 1 test cycle, this value shall be the one provided by the
(4) (h7) Sum of the CO2 emissions savings of each individual eco-innovation on Type I according UN/ECE Regulation No 83.
According to Annex XXI of Regulation (EU) 2017/1151 (if applicable)
Variant/Version …
5. Usage
3. CO2 4. CO2 factor (UF)
2. CO2
Decision 1. CO2 emissions of emissions of i.e. temporal CO2
approving Code of the emissions of the baseline the eco- share of emissions
cycle the eco-
the eco- eco-inno the baseline vehicle innovation technology savings
(NEDC/ innovation
inno vation (2) vehicle under vehicle usage in ((1 – 2) –
WLTP) vehicle
vation (1) (g/km) Type 1 under Type normal (3 – 4)) * 5
(g/km)
test-cycle (3) 1 test-cycle operation
conditions
xxx/201x … … … … … … … …
… … … … … … … … …
… … … … … … … … …
Total CO2 emissions savings on WLTP(g/km) (4)
(1) (h4) Number of the Commission Decision approving the eco-innovation.

(2) (h5) Assigned in the Commission Decision approving the eco-innovation.
(3) (h6) If a modelling methodology is applied instead of the type 1 test cycle, this value shall be the one provided by the
(4) (h7) Sum of the CO2 emissions savings of each individual eco-innovation on Type 1 according to Annex XXI, Sub-Annex 4
of Regulation (EU) 2017/1151.
02007L0046 — EN — 18.01.2018 — 021.001 — 255
▼M27
4.1. General code of the eco-innovation(s) (1): … . . . . . . . . . . . . . . . . . . . . . . . . . . .
Explanatory notes
(h) Eco-innovations.
(1) (h8) The general code of the eco-innovation(s) shall consist of the following elements
each separated by a blank space:
— Code of the approval authority as set out in Annex VII;
— Individual code of each eco-innovation fitted in the vehicle, indicated in chro
nological order of the Commission approval decisions.
(E.g. the general code of three eco-innovations approved chronologically as 10,
15 and 16 and fitted to a vehicle certified by the German type-approval authority
should be: ‘e1 10 15 16’.)
02007L0046 — EN — 18.01.2018 — 021.001 — 256
▼M27
ANNEX IX
EC CERTIFICATE OF CONFORMITY
0. OBJECTIVES
The certificate of conformity is a statement delivered by the vehicle manu
facturer to the buyer in order to assure him that the vehicle he has acquired
complies with the legislation in force in the European Union at the time it
was produced.
The certificate of conformity also serves the purpose to enable the

competent authorities of the Member States to register vehicles without
having to require the applicant to supply additional technical
documentation.
For these purposes, the certificate of conformity has to include:
(a) the Vehicle Identification Number;
(b) the exact technical characteristics of the vehicle (i.e. it is not permitted
to mention any range of value in the various entries).
1. GENERAL DESCRIPTION
1.1. The certificate of conformity shall consist of two parts.
(a) SIDE 1, which consists of a statement of compliance by the manu

facturer. The same template is common to all vehicle categories.
(b) SIDE 2, which is a technical description of the main characteristics of

the vehicle. The template of side 2 is adapted to each specific vehicle
category.
1.2. The certificate of conformity shall be established in a maximum format A4

(210 × 297 mm) or a folder of maximum format A4.
1.3. Without prejudice to the provisions in Section O(b), the values and units
indicated in the second part shall be those given in the type-approval docu
mentation of the relevant regulatory acts. In case of conformity of
production checks the values shall be verified according to the methods
laid down in the relevant regulatory acts. The tolerances allowed in those
regulatory acts shall be taken into account.
2. SPECIAL PROVISIONS
2.1. Model A of the certificate of conformity (complete vehicle) shall cover
vehicles which can be used on the road without requiring any further
stage for their approval.
2.2. Model B of the certificate of conformity (completed vehicles) shall cover

vehicles which have undergone a further stage for their approval.
This is the normal result of the multi-stage approval process (e.g. a bus built
by a second stage manufacturer on a chassis built by a vehicle manu
facturer).
The additional features added during the multi-stage process shall be

described briefly.
2.3. Model C of the certificate of conformity (incomplete vehicles) shall cover

vehicles which need a further stage for their approval (e.g. truck chassis).
Except for tractors for semi-trailers, certificates of conformity covering

chassis-cab vehicles belonging to category N shall be of Model C.
02007L0046 — EN — 18.01.2018 — 021.001 — 257
▼M27
PART I
COMPLETE AND COMPLETED VEHICLES
MODEL A1 — SIDE 1
COMPLETE VEHICLES
Side 1
The undersigned [… (Full name and position)] hereby certifies that the vehicle:
0.1. Make (Trade name of manufacturer): …
0.2. Type: …
— Variant (a): …
— Version (a): …
0.2.1. Commercial name: …
0.4. Vehicle category: …
0.5. Company name and address of manufacturer: …
0.6. Location and method of attachment of the statutory plates: …
Location of the vehicle identification number: …
0.9. Name and address of the manufacturer’s representative (if any): …
0.10. Vehicle identification number: …
conforms in all respects to the type described in approval (… type-approval

number including extension number) issued on (… date of issue) and
can be permanently registered in Member States having right/left (b) hand traffic
and using metric/imperial (c) units for the speedometer and metric/imperial (c)
units for the odometer (if applicable) (d).
(Place) (Date): … (Signature): …
MODEL A2 — SIDE 1
COMPLETE VEHICLES TYPE-APPROVED IN SMALL SERIES
[Year] [Sequential number]
Side 1
0.2. Type: …
02007L0046 — EN — 18.01.2018 — 021.001 — 258
▼M27

can be permanently registered in Member States having right/left (b) hand traffic
and using metric/imperial (c) units for the speedometer and metric/imperial (c)
units for the odometer (if applicable) (d).
MODEL B — SIDE 1
COMPLETED VEHICLES
Side 1
0.1. Make (Trade name of the manufacturer): …
0.2. Type: …
0.2.2. For multi-stage approved vehicles, type-approval information of the base/

previous stages vehicle (list the information for each stage):
— Type: …
Type-approval number, extension number …
manufacturer of the base/previous stage(s) vehicle…

02007L0046 — EN — 18.01.2018 — 021.001 — 259
▼M27
(a) has been completed and altered (1) as follows: … and
(b) conforms in all respects to the type described in approval (… type-

approval number including extension number) issued on (… date of
issue) and
(c) can be permanently registered in Member States having right/left (b) hand
traffic and using metric/imperial (c) units for the speedometer and metric/
imperial (c) units for the odometer (if applicable) (d).
Attachments: Certificate of conformity delivered at each previous stage.
SIDE 2
VEHICLE CATEGORY M1
(complete and completed vehicles)

Side 2
1. Number of axles: … and wheels: …
3. Powered axles (number, position, interconnection): … …
Main dimensions
4. Wheelbase (e): … mm
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
5. Length: … mm
6. Width: … mm
7. Height: … mm
Masses
13. Mass in running order: … kg
13.2. Actual mass of the vehicle: … kg
16.1. Technically permissible maximum laden mass: … kg
16.2. Technically permissible mass on each axle:
1. … kg
2. … kg
3. … kg etc.
16.4. Technically permissible maximum mass of the combination: … kg

02007L0046 — EN — 18.01.2018 — 021.001 — 260
▼M27
18.1. Drawbar trailer: … kg
18.3. Centre-axle trailer: … kg
18.4. Unbraked trailer: … kg
19. Technically permissible maximum static vertical mass at the coupling

point: … kg
Power plant
20. Manufacturer of the engine: …
21. Engine code as marked on the engine: …
22. Working principle: …
23.1. Class of Hybrid [electric] vehicle: OVC-HEV/NOVC-HEV/OVC-FCHV/

NOVC-FCHV (1)
24. Number and arrangement of cylinders: …
25. Engine capacity: … cm3
26. Fuel: Diesel/petrol/LPG/CNG-Biomethane/LNG/Ethanol/Biodiesel/Hydrogen (1)
26.1. Mono fuel/Bi fuel/Flex fuel/Dual-fuel (1)
26.2. (Dual-fuel only) Type 1A/Type 1B/Type 2A/Type 2B/Type 3B (1)
27. Maximum power
27.1. Maximum net power (g): … kW at … min–1 (internal combustion

engine) (1)
27.2. Maximum hourly output: … kW (electric motor) (1) (s)
27.3. Maximum net power: … kW (electric motor) (1) (s)
27.4. Maximum 30 minutes power: … kW (electric motor) (1) (s)
Maximum speed
29. Maximum speed: … km/h

30. Axle(s) track:
1. … mm
2. … mm
3. … mm
35. Tyre/wheel combination/Rolling Resistance Class (if applicable) (h): …
Brakes
36. Trailer brake connections mechanical/electric/pneumatic/hydraulic (1)
Bodywork
38. Code for bodywork (i): …
40. Colour of vehicle (j): …

02007L0046 — EN — 18.01.2018 — 021.001 — 261
▼M27
41. Number and configuration of doors: …
42. Number of seating positions (including the driver) (k): …
42.1. Seat(s) designated for use only when the vehicle is stationary: …
42.3. Number of wheelchair user accessible position: …
46. Sound level
— Stationary: … dB(A) at engine speed: … min-1
— Drive-by: … dB(A)
47. Exhaust emission level (l): Euro …
47.1. Parameters for emission testing
47.1.1. Test mass, kg: …
47.1.2. Frontal area, m2: …
47.1.3. Road load coefficients
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
48. Exhaust emissions (m) (m1) (m2):
applicable: …
1.1. test procedure: Type I or ESC (1)
CO: …. HC: ….. NO x: …. HC + NO x: …. Particulates: …..
Smoke opacity (ELR): … (m–1)
1.2. test procedure: Type 1 (NEDC average values, WLTP highest

values) or WHSC (EURO VI) (1)
CO: … THC: … NMHC: … NOx: … THC + NOx: … NH3: …

Particulates (mass): …
Particles (number): …
2.1. test procedure: ETC (if applicable)
CO: … NOx: … NMHC: … THC: … CH4: … Particulates: …
2.2. test procedure: WHTC (EURO VI)
CO: … NOx: … NMHC: … THC: … CH4: … NH3: …

Particulates (mass): …Particles (number): …
48.1. Smoke corrected absorption coefficient: … (m–1)
▼M28
48.2. Declared maximum RDE values (if applicable)
Complete RDE trip: NOx: … . . . . . . . , Particles (number): …. . . . . . . .
Urban RDE trip: NOx: … . . . . . . . . . , Particles (number): … . . . . . . . . .

02007L0046 — EN — 18.01.2018 — 021.001 — 262
▼M27
49. CO2 emissions/fuel consumption/electric energy consumption (m) (r):
1. all power trains, except pure electric vehicles (if applicable)
Fuel consumption in case of emission testing according to

NEDC values CO2 emissions
Regulation (EC) No 692/2008
Urban conditions (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
Extra-urban conditions (1): … g/km l/100 km or m3/100 km or kg/100 km (1)
Combined (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
Weighted (1), combined … g/km … l/100 km or m3/100 km or kg/100 km
Deviation factor (if applicable)
Verification factor (if applicable) ‘1’ or ‘0’
2. pure electric vehicles and OVC hybrid electric vehicles (if

applicable)
Electric energy consumption … Wh/km

(weighted, combined (1))
Electric range … km
3. Vehicle fitted with eco-innovation(s): yes/no (1)

3.1. General code of the eco-innovation(s) (p1): …
3.2. Total CO2 emissions savings due to the eco-innovation(s) (p2)

(repeat for each reference fuel tested):
3.2.1. NEDC savings: … g/km (if applicable)
3.2.2. WLTP savings: … g/km (if applicable)
4. all power trains, except pure electric vehicle, under

Regulation (EU) 2017/1151 (if applicable)
WLTP values CO2 emissions Fuel consumption
Low (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
Medium (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
High (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
Extra High (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 263
▼M27
Combined: … g/km … l/100 km or m3/100 km or kg/100 km (1)
Weighted, combined (1) … g/km … l/100 km or m3/100 km or kg/100 km (1)
5. Pure electric vehicles and OVC hybrid electric vehicles, under

5.1. Pure electric vehicles
Electric range city … km
5.2 OVC hybrid electric vehicles

(ECAC,weighted)
Electric range (EAER) … km
Electric range city (EAER city) … km
Miscellaneous
51. For special purpose vehicles: designation in accordance with Annex II
Section 5: …
52. Remarks (n): …
Additional tyre/wheel combinations: technical parameters (no reference to RR)
SIDE 2
VEHICLE CATEGORY M2

Side 2
1.1. Number and position of axles with twin wheels: …
2. Steered axles (number, position): …
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 264
▼M27
5. Length: … mm
6. Width: … mm
7. Height: … mm
9. Distance between the front end of the vehicle and the centre of the coupling
device: … mm
12. Rear overhang: … mm
Masses
13.1. Distribution of this mass amongst the axles:
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.
16.3. Technically permissible mass on each axle group:
1. … kg
2. … kg
3. … kg etc.
17. Intended registration/in service maximum permissible masses in national/

international traffic (1) (o)
17.1. Intended registration/in service maximum permissible laden mass: … kg
17.2. Intended registration/in service maximum permissible laden mass on each

axle:
1. … kg
2. … kg
3. … kg etc.

axle group:
1. … kg
2. … kg
3. … kg etc.
17.4. Intended registration/in service maximum permissible mass of the combi

nation: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 265
▼M27
19. Technically permissible maximum static mass at the coupling point: … kg
Power plant

NOVC-FCHV (1)
26. Fuel: Diesel/petrol/LPG/CNG-Biomethane/LNG/Ethanol/Biodiesel/

Hydrogen (1)
27. Maximum power

engine) (1)
28. Gearbox (type): …
Maximum speed

30. Axle(s) track:
1. … mm
2. … mm
3. … mm etc.
33. Drive axle(s) fitted with air suspension or equivalent: yes/no (1)
Brakes
37. Pressure in feed line for trailer braking system: … bar

02007L0046 — EN — 18.01.2018 — 021.001 — 266
▼M27
Bodywork
39. Class of vehicle: class I/Class II/Class III/Class A/Class B (1)
43. Number of standing places: …
Coupling device
44. Approval number or approval mark of coupling device (if fitted): …
45.1. Characteristics values (1): D: …/ V: …/ S: …/ U: …
46. Sound level
Stationary: … dB(A) at engine speed: … min–1
Drive-by: … dB(A)
47.1. Parameters for emission testing ►M29 (r) ◄
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …
1.1. test procedure: Type I or ESC (1)
CO: …. HC: ….. NO x: …. HC + NO x: …. Particulates: …..


Particulates (mass): …
Particles (number): …

Particulates (mass): … Particles (number): …
02007L0046 — EN — 18.01.2018 — 021.001 — 267
▼M27
▼M28
▼M27
Fuel consumption in case of emission testing under

NEDC according to Regulation (EC) No 692/2008

applicable)



4. all power trains, except pure electric vehicle, under


02007L0046 — EN — 18.01.2018 — 021.001 — 268
▼M27

5.2 OVC hybrid electric vehicles

(ECAC,weighted)
Miscellaneous
Section 5: …
SIDE 2
VEHICLE CATEGORY M3
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 269
▼M27
5. Length: … mm
6. Width: … mm
7. Height: … mm
device: … mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg

nation: … kg

02007L0046 — EN — 18.01.2018 — 021.001 — 270
▼M27
Power plant
27. Maximum power

engine) (1)
Maximum speed

30.1. Track of each steered axle: … mm
30.2. Track of all other axles: … mm
32. Position of loadable axle(s): …
35. Tyre/wheel combination (h): …
Brakes
Bodywork
39. Class of vehicle: class I/Class II/Class III/Class A/Class B (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 271
▼M27
42.2. Number of passenger seating positions: … (lower deck) … (upper deck)

(including the driver)
43. Number of standing places: …
Coupling device
46. Sound level
Drive-by: … dB(A)
▼M29
__________
▼M27
applicable: …
1.1. test procedure: ESC
CO: … HC: … NOx: … HC + NOx: … Particulates: …
1.2. test procedure: WHSC (EURO VI)

CO: … NOx: … NMHC: … THC: … CH4: … NH3: … Particulates

(mass): … Particles (number): …
Miscellaneous
Section 5: …

02007L0046 — EN — 18.01.2018 — 021.001 — 272
▼M27
SIDE 2
VEHICLE CATEGORY N1
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
5. Length: … mm
6. Width: … mm
7. Height: … mm.
8. Fifth wheel lead for semi-trailer towing vehicle (maximum and minimum):
… mm
device: … mm
11. Length of the loading area: … mm
Masses
1. … kg
2. … kg
3. … kg
14. Mass of the base vehicle in running order: … kg (1) (q)
1. … kg
2. … kg
3. … kg etc.
18.2. Semi-trailer: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 273
▼M27
Power plant

NOVC-FCHV (1)
27. Maximum power

engine) (1)
Maximum speed

30. Axle(s) track:
1. … mm
2. … mm
3. … mm
Brakes
Bodywork
40. Colour of vehicle (j): …

02007L0046 — EN — 18.01.2018 — 021.001 — 274
▼M27
Coupling device
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …
1.1. test procedure: Type 1 or ESC (1)



▼M28

02007L0046 — EN — 18.01.2018 — 021.001 — 275
▼M27
Fuel consumption in case of emission testing according

to Regulation (EC) No 692/2008
Combined (1): … g/km … l l/100 km or m3/100 km or kg/100 km (1)

applicable)


3.2. Total CO2 emissions saving due to the eco-innovation(s) (p2)

3.2.1. NEDC savings:… g/km (if applicable)
3.2.2. WLTP savings:… g/km (if applicable)
4. all power trains except pure electric vehicles under


02007L0046 — EN — 18.01.2018 — 021.001 — 276
▼M27

5.1. Pure electric vehicles (1) or (if applicable)
5.2 OVC hybrid electric vehicles (1) or (if applicable)

(ECAC,weighted)
Miscellaneous
50. Type-approved according to the design requirements for transporting
dangerous goods: yes/class(es): …/no (l):
Section 5: …
List of tyres: technical parameters (no reference to RR)
SIDE 2
VEHICLE CATEGORY N2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 277
▼M27
5. Length: … mm
6. Width: … mm
7. Height: … mm
… mm
device: … mm
Masses
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg

nation: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 278
▼M27
Power plant

NOVC-FCHV (1)
27. Maximum power

engine) (1)
Maximum speed

31. Position of lift axle(s): …
Brakes
Bodywork

02007L0046 — EN — 18.01.2018 — 021.001 — 279
▼M27
Coupling device
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …



▼M28

02007L0046 — EN — 18.01.2018 — 021.001 — 280
▼M30
49. Cryptographic hash of the manufacturer's record file . . . . . . . . . . . . . . . .
▼M27
Fuel consumption in case of emission testing according

to Regulation (EC) No 692/2008
Combined (1): … g/km … l l/100 km or m3/100 km or kg/100 km (1)

applicable)


3.2. Total CO2 emissions saving due to the eco-innovation(s) (p2)

3.2.1. NEDC savings:… g/km (if applicable)
3.2.2. WLTP savings:… g/km (if applicable)
4. all power trains except pure electric vehicles under

Extra High(1): … g/km … l/100 km or m3/100 km or kg/100 km (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 281
▼M27

5.1. Pure electric vehicles (1) or (if applicable)
5.2 OVC hybrid electric vehicles (1) or (if applicable)

(ECAC,weighted)
Miscellaneous
Section 5: …
SIDE 2
VEHICLE CATEGORY N3
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 282
▼M27
5. Length: … mm
6. Width: … mm
7. Height: … mm
… mm
device: … mm
Masses
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg

nation: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 283
▼M27
Power plant
27. Maximum power

engine) (1)
Maximum speed

Brakes
Bodywork

02007L0046 — EN — 18.01.2018 — 021.001 — 284
▼M27
Coupling device
46. Sound level
Drive-by: … dB(A)
▼M29
__________
▼M27
applicable: …
▼M30
49. Cryptographic hash of the manufacturer's record file . . . . . . . . . . . . . . . . . . .
▼M27
Miscellaneous
Section 5: …
SIDE 2
VEHICLE CATEGORIES O1 AND O2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 285
▼M27
5. Length: … mm
6. Width: … mm
7. Height: … mm
10. Distance between the centre of the coupling device and the rear end of the
vehicle: … mm
Masses
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.
19. Technically permissible maximum static mass on the coupling point of

a semi-trailer or centre-axle trailer: … kg
Maximum speed

34. Axle(s) fitted with air suspension or equivalent: yes/no (1)
Brakes
02007L0046 — EN — 18.01.2018 — 021.001 — 286
▼M27
Bodywork
38. Code for bodywork (l): …
Coupling device
Miscellaneous

Section 5: …
SIDE 2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
5. Length: … mm
6. Width: … mm
7. Height: … mm
vehicle: … mm
Masses
1. … kg
2. … kg
3. … kg

02007L0046 — EN — 18.01.2018 — 021.001 — 287
▼M27
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg
19. Technically permissible maximum static mass on the coupling point of

Maximum speed

Brakes
Bodywork
Coupling device
45.1. Characteristics values (1): D: …/ V: …/ S: …/ U: …å

02007L0046 — EN — 18.01.2018 — 021.001 — 288
▼M27
Miscellaneous

Section 5: …
PART II
INCOMPLETE VEHICLES
MODEL C1 — SIDE 1
INCOMPLETE VEHICLES
Side 1
0.2. Type: …
Variant (a): …
Version (a): …
0.2.2. For multi-stage approved vehicles, type-approval information of the base/

previous stages vehicle
(list the information for each stage):
Type: …
Variant (a): …
Version (a): …
Type-approval number, extension number …
manufacturer of the base/previous stage(s) vehicle …

cannot be permanently registered without further approvals.

02007L0046 — EN — 18.01.2018 — 021.001 — 289
▼M27
MODEL C2 — SIDE 1
INCOMPLETE VEHICLES TYPE-APPROVED IN SMALL SERIES
[Year] [Sequential number]
Side 1
0.2. Type: …
Variant (a): …
Version (a): …

cannot be permanently registered without further approvals.
SIDE 2
VEHICLE CATEGORY M1
(incomplete vehicles)
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
5.1. Maximum permissible length: … mm

02007L0046 — EN — 18.01.2018 — 021.001 — 290
▼M27
6.1. Maximum permissible width: … mm
7.1. Maximum permissible height: … mm
12.1. Maximum permissible rear overhang: … mm
Masses
14. Mass in running order of the incomplete vehicle: … kg
1. … kg
2. … kg
3. … kg
15. Minimum mass of the vehicle when completed: … kg
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
19. Technically permissible maximum static vertical mass at the coupling

point: … kg
Power plant

Hydrogen (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 291
▼M27
27. Maximum power

engine) (1)
Maximum speed

30. Axle(s) track:
1. … mm
2. … mm
3. … mm
Brakes
Bodywork
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …

values)or WHSC (EURO VI) (1)

02007L0046 — EN — 18.01.2018 — 021.001 — 292
▼M27

▼M29
1. All power trains, except pure electric vehicles (if applicable)
NEDC values CO2 emissions Fuel consumption
Extra-urban conditions (1): … g/km … l/100 km or m3/100 km or kg/100 km (1)
2. Pure electric vehicles and OVC hybrid electric vehicles (if

applicable)



4. All power trains, except pure electric vehicle, under


02007L0046 — EN — 18.01.2018 — 021.001 — 293
▼M29

5.2. OVC hybrid electric vehicles

(ECAC,weighted)
▼M27
Miscellaneous
SIDE 2
VEHICLE CATEGORY M2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
02007L0046 — EN — 18.01.2018 — 021.001 — 294
▼M27
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg

nation: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 295
▼M27
Power plant

Hydrogen (1)
27. Maximum power

engine) (1)
Maximum speed

30. Axle(s) track:
1. … mm
2. … mm
3. … mm
Brakes

02007L0046 — EN — 18.01.2018 — 021.001 — 296
▼M27
Coupling device
45. Type or classes of coupling devices which can be fitted: …
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …

values)or WHSC (EURO VI) (1)


▼M29

02007L0046 — EN — 18.01.2018 — 021.001 — 297
▼M29

applicable)




02007L0046 — EN — 18.01.2018 — 021.001 — 298
▼M29

(ECAC,weighted)
▼M27
Miscellaneous
SIDE 2
VEHICLE CATEGORY M3
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
02007L0046 — EN — 18.01.2018 — 021.001 — 299
▼M27
1. … kg
2. … kg
3. … kg etc.
axle:
1. … kg
2. … kg
3. … kg
axle group:
1. … kg
2. … kg
3. … kg
nation: … kg
Power plant
27. Maximum power
engine) (1)
Maximum speed
02007L0046 — EN — 18.01.2018 — 021.001 — 300
▼M27
Brakes
Coupling device
45. Types or classes of coupling devices which can be fitted: …
46. Sound level
Drive-by: … dB(A)
▼M29
__________
▼M27
applicable: …


Miscellaneous
02007L0046 — EN — 18.01.2018 — 021.001 — 301
▼M27
SIDE 2
VEHICLE CATEGORY N1
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
… mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
02007L0046 — EN — 18.01.2018 — 021.001 — 302
▼M27
Power plant

Hydrogen (1)
27. Maximum power

engine) (1)
Maximum speed

30. Axle(s) track:
1. … mm
2. … mm
3. … mm
Brakes
Coupling device

02007L0046 — EN — 18.01.2018 — 021.001 — 303
▼M27
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2
applicable: …


CO: … NOx: … NMHC: … THC: … CH4: … Particulates:

Particulates (mass): … Particles (number):
▼M29

02007L0046 — EN — 18.01.2018 — 021.001 — 304
▼M29

applicable)






02007L0046 — EN — 18.01.2018 — 021.001 — 305
▼M29

(ECAC,weighted)
▼M27
Miscellaneous
SIDE 2
VEHICLE CATEGORY N2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
… mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 306
▼M27
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg

axle group:
1. … kg
2. … kg
3. … kg

nation: … kg
Power plant

02007L0046 — EN — 18.01.2018 — 021.001 — 307
▼M27
Hydrogen (1)
27. Maximum power

engine) (1)
Maximum speed

Brakes
Coupling device
46. Sound level
Drive-by: … dB(A)
47.1.3.0. f0, N:
47.1.3.1. f1, N/(km/h):
47.1.3.2. f2, N/(km/h)2

02007L0046 — EN — 18.01.2018 — 021.001 — 308
▼M27
applicable: …



▼M29

applicable)




02007L0046 — EN — 18.01.2018 — 021.001 — 309
▼M29


(ECAC,weighted)
▼M27
Miscellaneous
SIDE 2
VEHICLE CATEGORY N3
Side 2
02007L0046 — EN — 18.01.2018 — 021.001 — 310
▼M27
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
… mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.
17.2. Intended registration/in service maximum permissible laden mass on each axle:
1. … kg
2. … kg
3. … kg
axle group:
1. … kg
2. … kg
3. … kg
nation: … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 311
▼M27


Power plant




27. Maximum power

engine) (1)


Maximum speed


Brakes

Coupling device

46. Sound level
Drive-by: … dB(A)
▼M29
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 312
▼M27
applicable: …


Miscellaneous
SIDE 2
Side 2
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
vehicle: … mm
Masses
1. … kg
2. … kg
3. … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 313
▼M27
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.
19.1. Technically permissible maximum static mass on the coupling point of

Maximum speed

Coupling device
Miscellaneous
SIDE 2
Side 2
2. Steered axle (number, position): …

02007L0046 — EN — 18.01.2018 — 021.001 — 314
▼M27
Main dimensions
4.1. Axle spacing:
1-2: … mm
2-3: … mm
3-4: … mm
5.1. Maximum permissible length: …mm
6.1. Maximum permissible width: …mm
7.1. Maximum permissible height: …mm
vehicle: …mm
12.1. Maximum permissible rear overhang: …mm
Masses
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg
1. … kg
2. … kg
3. … kg etc.
1. … kg
2. … kg
3. … kg etc.


axle:
1. … kg
2. … kg
3. … kg
02007L0046 — EN — 18.01.2018 — 021.001 — 315
▼M27
axle group:
1. … kg
2. … kg
3. … kg
19.1. Technically permissible maximum static mass on the coupling point of

Maximum speed

Coupling device
Miscellaneous
Explanatory notes relating to Annex IX

(1) Delete where not applicable
(a) Indicate the identification code —
(b) Indicate whether the vehicle is suitable for use in either right or left-hand traffic or both
right and left-hand traffic.
(c) Indicate whether the speedometer and/or odometer fitted has metric or both metric and
imperial units.
(d) This statement shall not restrict the right of the Member States to require technical
adaptations in order to allow the registration of a vehicle in a Member State other than
the one for which it was intended when the direction of the traffic is on the opposite
side of the road.
(e) Entries 4 and 4.1 shall be completed in accordance with definitions 25 (Wheelbase) and
26 (Axle spacing) of Regulation (EU) No 1230/2012 respectively
— —
(g) For hybrid electric vehicles, indicate both power outputs.

(h) Optional equipment under this letter can be added under entry ‘Remarks’.
(i) The codes described in Annex II Letter C shall be used.
(j) Indicate only the basic colour(s) as follows: white, yellow, orange, red, violet, blue,
green, grey, brown or black.
(k) Excluding seats designated for use only when the vehicle is stationary and the number
of wheelchair positions.
For coaches belonging to the vehicle category M3 the number of crew members shall
be included in the passenger number.
(l) Add the number of the Euro level and the character corresponding to the provisions
used for type-approval.
02007L0046 — EN — 18.01.2018 — 021.001 — 316
▼M27
(m) Repeat for the various fuels that can be used. Vehicles that can be fuelled with both
petrol and gaseous fuel but in which the petrol system is fitted for emergency purposes
or for starting only and the petrol tank of which cannot contain more than 15 litres of
petrol will be regarded as vehicles that can only run on a gaseous fuel.
(m1) In case of EURO VI dual-fuel engines and vehicles, repeat as appropriate.
(m2) Solely emissions assessed in accordance with the applicable regulatory act or acts shall
be stated.
(n) If the vehicle is equipped with 24 GHz short-range radar equipment in accordance with
Commission Decision 2005/50/EC (OJ L 21, 25.1.2005, p. 15), the manufacturer shall
indicate here: ‘Vehicle equipped with 24 GHz short-range radar equipment’.
(o) The manufacturer may complete these entries either for international traffic or national
traffic or both.
For national traffic, the code of the country where the vehicle is intended to be
registered shall be mentioned. The code shall be in accordance with standard ISO
3166-1:2006.
For international traffic, the directive number shall be referred to (e.g. ‘96/53/EC’ for
Council Directive 96/53/EC).
(p) Eco-innovations.
(p1) The general code of the eco-innovation(s) shall consist of the following elements, each
separated by a blank space:
— Code of the approval authority as set out in Annex VII;
— Individual code of each eco-innovation fitted in the vehicle, indicated in chro
nological order of the Commission approval decisions.
(E.g. the general code of three eco-innovations approved chronologically as 10, 15
and 16 and fitted to a vehicle certified by the German type-approval authority
should be: ‘e1 10 15 16’.)
(p2) Sum of the CO2 emissions savings of each individual eco-innovation.
(q) In the case of completed vehicles of category N1 within the scope of Regulation (EC)
No 715/2007.
(r) Only applicable if the vehicle is approved to Regulation (EC) 715/2007
(s) In the case of more than one electric motor indicate the consolidated effect of all the
engines.
02007L0046 — EN — 18.01.2018 — 021.001 — 317
▼M9
ANNEX X
CONFORMITY OF PRODUCTION PROCEDURES
0. Objectives
0.1. The conformity of production procedure aims to ensure that each
produced vehicle, system, component and technical separate unit is in
conformity with the approved type.
0.2. Procedures include inseparably the assessment of quality management

systems, referred to below as ‘initial assessment’ and verification of the
approval subject and product-related controls, referred to as ‘product
conformity arrangements’.
1. Initial assessment
1.1. The approval authority of a Member State shall verify the existence of
satisfactory arrangements and procedures for ensuring effective control
so that components, systems, separate technical units or vehicles when in
production conform to the approved type.
1.2. Guidance for conducting assessments may be found in Standard EN ISO

19011:2002 — Guidelines for quality and/or environmental management
systems auditing.
1.3. The requirements referred to in point 1.1 shall be verified to the satis
faction of the authority granting type-approval.
That authority shall be satisfied with the initial assessment and the
product conformity arrangements at section 2 below, taking account as
necessary of one of the arrangements described in points 1.3.1 to 1.3.3,
or a combination of those arrangements in full or in part as appropriate.
1.3.1. The actual initial assessment and/or verification of product conformity

arrangements shall be carried out by the approval authority granting the
approval or an appointed body acting on behalf of the approval
authority.
1.3.1.1. When considering the extent of the initial assessment to be carried out,
the approval authority may take account of available information relating
to:
(a) the manufacturer’s certification described in point 1.3.3 below,

which has not been qualified or recognised under that point;
(b) in the case of component or separate technical unit type-approval,

quality system assessments performed in the component or separate
technical unit manufacturer’s premises by vehicle manufacturer(s),
according to one or more of the industry sector specifications
satisfying the requirements in harmonised standard EN ISO
9001:2008.
1.3.2. The actual initial assessment and/or verification of product conformity

arrangements may also be carried out by the approval authority of
another Member State or the appointed body designated for this
purpose by the approval authority.
02007L0046 — EN — 18.01.2018 — 021.001 — 318
▼M9
1.3.2.1. In such a case, the approval authority of the other Member State shall
prepare a statement of compliance outlining the areas and production
facilities it has covered as relevant to the product(s) to be type-approved
and to the regulatory acts according to which these products are to be
type-approved.
1.3.2.2. On receiving an application for a compliance statement from the

approval authority of a Member State granting type-approval, the
approval authority of another Member State shall send forthwith the
statement of compliance or advise that it is not in a position to
provide such a statement.
1.3.2.3. The statement of compliance shall include at least the following:
(a) Group or company (e.g. XYZ Automotive)
(b) Particular organisation (e.g. European Division)
(c) Plants/Sites (e.g. Engine Plant 1 (United

Kingdom) — Vehicle Plant 2
(Germany))
(d) Vehicle/Component range (e.g. All Category M1 models)
(e) Areas assessed (e.g. Engine assembly, body

pressing and assembly, vehicle
assembly)
(f) Documents examined (e.g. Company and site quality

manual and procedures)
(g) Date of the assessment (e.g. Audit conducted from 18 to

30.5.2009)
(h) Planned monitoring visit (e.g. October 2010)
1.3.3. The approval authority shall also accept the manufacturer’s suitable
certification to harmonised standard EN ISO 9001:2008 or an equivalent
harmonised standard as satisfying the initial assessment requirements of
point 1.3. The manufacturer shall provide details of the certification and
undertake to inform the approval authority of any revisions to its validity
or scope.
1.4. For the purpose of vehicle type-approval, the initial assessments carried
out for granting approvals for systems, components and technical units
of the vehicle need not be repeated but shall be completed by an
assessment covering the locations and activities relating to the
assembly of the whole vehicle not covered by the former assessments.
2. Product conformity arrangements

2.1. Every vehicle, system, component or separate technical unit approved
pursuant to this Directive or a separate Directive or Regulation shall be
so manufactured as to conform to the type approved by meeting the
requirements of this Directive or the applicable regulatory acts listed in
Annex IV.
02007L0046 — EN — 18.01.2018 — 021.001 — 319
▼M9
2.2. The approval authority of a Member State shall verify the existence of
adequate arrangements and documented control plans, to be agreed with
the manufacturer for each approval, to carry out at specified intervals
those tests or associated checks necessary to verify continued conformity
with the approved type including specifically physical tests specified in
the regulatory acts.
2.3. The holder of the type-approval shall, in particular:
2.3.1. ensure the existence and application of procedures for effective control
of the conformity of products (vehicles, systems, components or separate
technical units) to the approved type;
2.3.2. have access to the testing or other appropriate equipment necessary for
checking the conformity to each approved type;
2.3.3. ensure that test or check results data are recorded and that annexed
documents remain available for a period to be determined in
agreement with the approval authority. This period shall not exceed
10 years;
2.3.4. analyse the results of each type of test or check, in order to verify and
ensure the stability of the product characteristics, making allowance for
variation of an industrial production;
2.3.5. ensure that for each type of product, at least the checks prescribed in this
Directive and the tests prescribed in the applicable regulatory acts listed
in Annex IV are carried out;
2.3.6. ensure that any set of samples or test pieces, giving evidence of
non-conformity in the type of test or check in question gives rise to a
further sampling and test or check. All the necessary steps shall be taken
to restore conformity of the corresponding production;
2.3.7. in the case of vehicle type-approval, the checks referred to in point 2.3.5
shall at least consist in verifying the correct built specifications in
relation to the approval and the information required for certificates of
conformity given in Annex IX.
3. Continued verification arrangements

3.1. The authority which has granted type-approval may at any time verify
the conformity control methods applied in each production facility.
3.1.1. The normal arrangements shall be to monitor the continued effectiveness

of the procedures laid down in Sections 1 and 2 (initial assessment and
product conformity arrangements) of this Annex.
3.1.1.1. Surveillance activities carried out by the technical services (qualified or

recognised as required in point 1.3.3) shall be accepted as satisfying the
requirements of point 3.1.1 with regard to the procedures established at
initial assessment.
3.1.1.2. The normal frequency of verifications by the approval authority (other

than those referred to in point 3.1.1.1) shall be such as to ensure that the
relevant controls applied in accordance with Sections 1 and 2 are
reviewed over a period consistent with the climate of trust established
by the approval authority.
02007L0046 — EN — 18.01.2018 — 021.001 — 320
▼M9
3.2. At every review, records of tests or checks and records of production
shall be made available to the inspector; in particular, records of those
tests or checks documented as required in point 2.2.
3.3. The inspector may select samples at random to be tested in the manu
facturer’s laboratory or in the facilities of the technical service. In such a
case only physical test shall be carried out. The minimum number of
samples may be determined according to the results of the manu
facturer’s own verification.
3.4. Where the level of control appears unsatisfactory, or when it seems
necessary to verify the validity of the tests carried out in accordance
with point 3.2, the inspector shall select samples to be sent to a technical
service to perform physical tests.
3.5. Where unsatisfactory results are found during an inspection or a moni
toring review, the approval authority shall ensure that all necessary steps
are taken to restore conformity of production as rapidly as possible.
02007L0046 — EN — 18.01.2018 — 021.001 — 321
▼M22
ANNEX XI
NATURE OF AND PROVISIONS FOR THE EC TYPE-APPROVAL OF SPECIAL PURPOSE VEHICLES
Appendix 1
Motor-Caravans, Ambulances and Hearses
Regulatory act M1 ≤ M1 >

Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
1 Permissible Sound level Directive 70/ H G+H G+H G+H

157/EEC
▼M23
1A Sound level Regulation H G+H G+H G+H

(EU) No 540/
2014
▼M22
2 Emissions (Euro 5 and 6) light duty Regulation Q (1) G+Q (1) G+Q (1)
vehicles/access to information (EC) 715/2007
▼M6
▼C1
_____
▼M22
3A Prevention of fire risks (liquid fuel Regulation F (2) F (2) F (2) F (2)
tanks) (EC) No 661/
2009
UNECE
Regulation
No 34
3B Rear underrun protective devices Regulation X X X X

(RUPDs) and their installation; rear (EC) No 661/
underrun protection (RUP) 2009
UNECE
Regulation
No 58
▼M6
▼C1
_____
▼M22
4A Space for mounting and fixing rear Regulation X X X X

registration plates (EC) No 661/
2009
Regulation
(EU) No 1003/
2010
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 322
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
5A Steering equipment Regulation X G G G

(EC) No 661/
2009
UNECE
Regulation
No 79
▼M6
▼C1
_____
▼M22
6A Vehicle access and manoeuvrability Regulation X X

(EC) No 661/
2009
Regulation
(EU) No 130/
2012
6B Door latches and door retention Regulation B G+B

components (EC) No 661/
2009
UNECE
Regulation
No 11
▼M6
▼C1
_____
▼M22
7A Audible warning devices and signals Regulation X X X X

(EC) No 661/
2009
UNECE
Regulation
No 28
▼M6
▼C1
_____
▼M22
8A Devices for indirect vision and their Regulation X G G G

installation (EC) No 661/
2009
UNECE
Regulation
No 46
▼M6
▼C1
_____
▼M22
9A Braking of vehicles and trailers Regulation X (4) G+A1

(EC) No 661/
2009
UNECE
Regulation
No 13-H
02007L0046 — EN — 18.01.2018 — 021.001 — 323
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
9B Braking of vehicles and trailers Regulation G(3) G(3)

(EC) No 661/
2009
UNECE
Regulation
No 13
▼M6
▼C1
_____
▼M22
10A Electromagnetic compatibility Regulation X X X X

(EC) No 661/
2009
UNECE
Regulation
No 10
▼M6
▼C1
_____
▼M22
12A Interior fittings Regulation C G+C

(EC) No 661/
2009
UNECE
Regulation
No 21
▼M6
▼C1
_____
▼M22
13A Protection of motor vehicles against Regulation G (4A) G (4A)

unauthorised use (EC) No 661/
2009
UNECE
Regulation
No 18
13B Protection of motor vehicles against Regulation X G

unauthorised use (EC) No 661/
2009
UNECE
Regulation
No 116
▼M6
▼C1
_____
▼M22
14A Protection of the driver against the Regulation X G

steering mechanism in the event of (EC) No 661/
impact 2009
UNECE
Regulation
No 12
02007L0046 — EN — 18.01.2018 — 021.001 — 324
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
▼M6
▼C1
_____
▼M22
15A Seats, their anchorages and any head Regulation D G+D G+D (4B) G+D (4B)
restraints (EC) No 661/
2009
UNECE
Regulation
No 17
15B Seats of large passenger vehicles Regulation X X

(EC) No 661/
2009
UNECE
Regulation
No 80
▼M6
▼C1
_____
▼M22
16A External projections Regulation X for the G for the

(EC) No 661/ cab; A+Z cab; A+Z
2009 for the for the
UNECE remaining remaining
Regulation part part
No 26
▼M6
▼C1
_____
▼M22
17A Vehicle access and manoeuvrability Regulation X X X X

(EC) No 661/
2009
Regulation
(EU) No 130/
2012
17B Speedometer equipment including its Regulation X X X X

installation (EC) No 661/
2009
UNECE
Regulation
No 39
▼M6
▼C1
_____
▼M22
18A Manufacturer’s statutory plate and Regulation X X X X

vehicle identification number (EC) No 661/
2009
Regulation
(EU) No 19/
2011
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 325
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
19A Safety-belt anchorages, Isofix Regulation D G+L G+L G+L

anchorages systems and Isofix top (EC) No 661/
tether anchorages 2009
UNECE
Regulation
No 14
▼M6
▼C1
_____
▼M22
20A Installation of lighting and Regulation A+N A+G+N for A+G+N A+G+N
light-signalling devices on vehicles (EC) No 661/ the cab; for the for the
2009 A+N for cab; A+N cab; A+N
UNECE the for the for the
Regulation remaining remainin remaining
No 48 part g part part
▼M6
▼C1
_____
▼M22
21A Retro-reflecting devices for Regulation X X X X

power-driven vehicles and their (EC) No 661/
trailers 2009
UNECE
Regulation
No 3
▼M6
▼C1
_____
▼M22
22A Front and rear position lamps, Regulation X X X X

stop-lamps and end-ouline marker (EC) No 661/
lamps for motor vehicles and their 2009
trailers UNECE
Regulation
No 7
22B Daytime running lamps for Regulation X X X X

power-driven vehicles (EC) No 661/
2009
UNECE
Regulation
No 87
22C Side-marker lamps for motor Regulation X X X X

vehicles and their trailers (EC) No 661/
2009
UNECE
Regulation
No 91
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 326
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
23A Direction indicators for Regulation X X X X

power-driven vehicles and their (EC) No 661/
trailers 2009
UNECE
Regulation
No 6
▼M6
▼C1
_____
▼M22
24A Illumination of rear-registration Regulation X X X X

plates of power-driven vehicles and (EC) No 661/
their trailers 2009
UNECE
Regulation
No 4
▼M6
▼C1
_____
▼M22
25A Power-driven vehicle’s sealed-beam Regulation X X X X

headlamps (SB) emitting an (EC) No 661/
European asymmetrical passing 2009
beam or a driving beam or both UNECE
Regulation
No 31
25B Filament lamps for use in approved Regulation X X X X

lamp units of power-driven vehicles (EC) No 661/
UNECE
Regulation
No 37
25C Motor vehicle headlamps equipped Regulation X X X X

with gas-discharge light sources (EC) No 661/
2009
UNECE
Regulation
No 98
25D Gas-discharge light sources for use Regulation X X X X

in approved gas-discharge lamp (EC) No 661/
units of power-driven vehicles 2009
UNECE
Regulation
No 99
25E Motor vehicle headlamps emitting Regulation X X X X

an asymmetrical passing beam or a (EC) No 661/
driving beam or both and equipped 2009
with filament lamps and/or LED UNECE
modules Regulation
No 112
02007L0046 — EN — 18.01.2018 — 021.001 — 327
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
25F Adaptive front-lighting Regulation X X X X

systems (AFS) for motor vehicles (EC) No 661/
2009
UNECE
Regulation
No 123
▼M6
▼C1
_____
▼M22
26A Power-driven vehicle front fog Regulation X X X X

lamps (EC) No 661/
2009
UNECE
Regulation
No 19
▼M6
▼C1
_____
▼M22
27A Towing device Regulation E E E E

(EC) No 661/
2009
Regulation
(EU) No 1005/
2010
▼M6
▼C1
_____
▼M22
28A Rear fog lamps for power-driven Regulation X X X X

2009
UNECE
Regulation
No 38
▼M6
▼C1
_____
▼M22
29A Reversing lights for power-driven Regulation X X X X

2009
UNECE
Regulation
No 23
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 328
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
30A Parking lamps for power-driven Regulation X X X X

vehicles (EC) No 661/
2009
UNECE
Regulation
No 77
▼M6
▼C1
_____
▼M22
31A Safety-belts, restraint systems, child Regulation D G+M G+M G+M

restraint systems and Isofix child (EC) No 661/
restraint systems 2009
UNECE
Regulation
No 16
▼M6
▼C1
_____
▼M22
32A Forward field of vision Regulation X G

(EC) No 661/
2009
UNECE
Regulation
No 125
▼M6
▼C1
_____
▼M22
33A Location and identification of hand Regulation X X X X

controls, tell-tales and indicators (EC) No 661/
2009
UNECE
Regulation
No 121
▼M6
▼C1
_____
▼M22
34A Windscreen defrosting and Regulation X G (5) (5) (5)

demisting systems (EC) No 661/
2009
Regulation
(EU) No 672/
2010
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 329
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
35A Windscreen wiper and washer Regulation X G (6) (6) (6)

systems (EC) No 661/
2009
Regulation
(EU) No 1008/
2010
▼M6
▼C1
_____
▼M22
36A Heating systems Regulation X X X X

(EC) No 661/
2009
UNECE
Regulation
No 122
▼M6
▼C1
_____
▼M22
37A Wheel guards Regulation X G

(EC) No 661/
2009
Regulation
(EU) No 1009/
2010
▼M6
▼C1
_____
▼M24
38A Head restraints (headrests), whether Regulation D G+D

or not incorporated in vehicle seats (EC) No 661/
2009
UNECE
Regulation
No 25
▼M22
41 Emissions (Euro IV and V) heavy Directive H (8) G+H (8) G+H (8) G+H (8)
duty vehicles 2005/55/EC
41A Emissions (Euro VI) heavy duty Regulation G+H (9) G+H (9) G+H (9) G+H (9)
vehicles/access to information (EC) No 595/
2009
▼M6
▼C1
_____
▼M22
44A Masses and dimensions Regulation X X

(EC) No 661/
2009
Regulation
(EU) No 1230/
2012
02007L0046 — EN — 18.01.2018 — 021.001 — 330
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
▼M6
▼C1
_____
▼M22
45A Safety glazing materials and their Regulation J G+J G+J G+J
installation on vehicles (EC) No 661/
2009
UNECE
Regulation
No 43
▼M6
_____
▼M22
46A Installation of tyres Regulation X G G G

(EC) No 661/
2009
Regulation
(EU) No 458/
2011
46B Pneumatic tyres for motor vehicles Regulation X G

and their trailers (Class C1) (EC) No 661/
2009
UNECE
Regulation
No 30
46C Pneumatic tyres for commercial Regulation — G G G

vehicles and their trailers (Classes (EC) No 661/
C2 and C3) 2009
UNECE
Regulation
No 54
46D Tyre rolling sound emissions, Regulation X G G G

adhesion on wet surfaces and (EC) No 661/
rolling resistance (Classes C1, C2 2009
and C3) UNECE
Regulation
No 117
46E Temporary-use spare unit, run-flat Regulation X G

tyres/system and tyre pressure moni (EC) No 661/
toring system 2009
UNECE
Regulation
No 64
▼M6
▼C1
_____
▼M22
47A Speed limitation of vehicles Regulation X X

(EC) No 661/
2009
UNECE
Regulation
No 89
02007L0046 — EN — 18.01.2018 — 021.001 — 331
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
▼M6
▼C1
_____
▼M22
48A Masses and dimensions Regulation X X

(EC) No 661/
2009
Regulation
(EU) No 1230/
2012
▼M6
▼C1
_____
▼M22
50A Mechanical coupling components of Regulation X (10) G (10) G (10) G (10)

combinations of vehicles (EC) No 661/
2009
UNECE
Regulation
No 55
▼M6
▼C1
_____
▼M22
51A Burning behaviour of materials used Regulation G for the

in the interior construction of certain (EC) No 661/ cab; X for
categories of motor vehicles 2009 the
UNECE remaining
Regulation part
No 118
▼M6
▼C1
_____
▼M22
52A M2 and M3 vehicles Regulation A A

(EC) No 661/
2009
UNECE
Regulation
No 107
52B Strength of the superstructure of Regulation A A

large passenger vehicles (EC) No 661/
2009
UNECE
Regulation
No 66
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 332
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
53A Protection of occupants in the event Regulation N/A N/A

of a frontal collision (EC) No 661/
2009
UNECE
Regulation
No 94
▼M6
▼C1
_____
▼M22
54A Protection of occupants in the event Regulation N/A N/A

of lateral collision (EC) No 661/
2009
UNECE
Regulation
No 95
58 Pedestrian protection Regulation X N/A.

(EC) No 78/ However,
2009 any frontal
protection
systems
supplied
with the
vehicle
shall
comply and
shall be
marked
59 Recyclability Directive N/A N/A

2005/64/EC
61 Air-conditioning system Directive X G (14)

2006/40/EC
62 Hydrogen system Regulation X X X X

(EC) No 79/
2009
63 General Safety Regulation X (15) X (15) X (15) X (15)

(EC) No 661/
2009
64 Gear shift indicators Regulation X G

(EC) No 661/
2009
Regulation
(EU) No 65/
2012
65 Advanced emergency braking Regulation N/A (16) N/A (16)

system (EC) No 661/
2009
Regulation
(EU) No 347/
2012
02007L0046 — EN — 18.01.2018 — 021.001 — 333
▼M22
Item Subject M2 M3
reference 2 500 kg (*) 2 500 kg (*)
66 Lane departure warning system Regulation N/A (17) N/A (17)

(EC) No 661/
2009
Regulation
(EU) No 351/
2012
67 Specific components for liquefied Regulation X X X X

petroleum gases (LPG) and their (EC) No 661/
installation on motor vehicles 2009
UNECE
Regulation
No 67
68 Vehicle alarm systems (VAS) Regulation X G

(EC) No 661/
2009
UNECE
Regulation
No 97
69 Electrical safety Regulation X X X X

(EC) No 661/
2009
UNECE
Regulation
No 100
70 Specific components for CNG and Regulation X X X X

their installation on motor vehicules (EC) No 661/
2009
UNECE
Regulation
No 110
(*) Technically permissible maximum laden mass
Additional requirements for ambulances

The patient compartment of ambulances shall comply with the requirements of
EN 1789:2007 +A1: 2010 +A2:2014 on Medical vehicles and their equipment –
Road ambulances with the exception of Section 6.5, list of equipment. Proof of
compliance shall be provided with a test report of a technical service. If a
Wheelchair space is foreseen, the requirements of Appendix 3 relating to the
wheelchair tie down and occupant restraint systems shall apply.
▼M22
Appendix 2
Armoured Vehicles
Item Subject Reference to regulatory act M1 M2 M3 N1 N2 N3 O1 O2 O3 O4
1 Permissible sound level Directive 70/157/EEC X X X X X X
▼M23
1A Sound level Regulation (EU) No 540/2014 X X X X X X
▼M22
2 Emissions (Euro 5 and 6) light duty vehicles/ Regulation (EC) No 715/2007 A (1) A (1) A (1) A (1)
access to information
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 334

▼M22
3A Prevention of fire risks (liquid fuel tanks) Regulation (EC) No 661/2009 X (2) X (2) X (2) X (2) X (2) X (2) X X X X
3B Rear underrun protective devices (RUPDs) Regulation (EC) No 661/2009 X X X X A A X X X X

and their installation; rear underrun UNECE Regulation No 58
protection (RUP)
▼M6
▼C1
_____
▼M22
4A Space for mounting and fixing rear regis Regulation (EC) No 661/2009 X X X X X X X X X X
tration plates Regulation (EU) No 1003/2010
▼M22
▼M6
▼C1
_____
▼M22
5A Steering equipment Regulation (EC) No 661/2009 X X X X X X X X X X

▼M6
▼C1
_____
▼M22
6A Vehicle access and manoeuvrability Regulation (EC) No 661/2009 X X X X X X

02007L0046 — EN — 18.01.2018 — 021.001 — 335

6B Door latches and door retention components Regulation (EC) No 661/2009 X X
▼M6
▼C1
_____
▼M22
7A Audible warning devices and signals Regulation (EC) No 661/2009 A+K A+K A+K A+K A+K A+K
▼M6
▼C1
_____
▼M22
8A Devices for indirect vision and their instal Regulation (EC) No 661/2009 A A A A A A
lation UNECE Regulation No 46
▼M6
▼C1
_____
▼M22
9A Braking of vehicles and trailers Regulation (EC) No 661/2009 X (3) X (3) X (3) X (3) X (3) X (3) X (3) X (3) X (3)
9B Braking of passenger cars Regulation (EC) No 661/2009 X (4) X (4)

UNECE Regulation No 13-H
▼M6
▼C1
02007L0046 — EN — 18.01.2018 — 021.001 — 336

_____
▼M22
10A Electromagnetic compatibility Regulation (EC) No 661/2009 X X X X X X X X X X

▼M6
▼C1
_____
▼M22
12A Interior fittings Regulation (EC) No 661/2009 A

▼M22
▼M6
▼C1
_____
▼M22
13A Protection of motor vehicles against unauth Regulation (EC) No 661/2009 X (4A) X (4A) X (4A) X (4A)
orised use UNECE Regulation No 18
13B Protection of motor vehicles against unauth Regulation (EC) No 661/2009 X X

orised use UNECE Regulation No 116
▼M6
▼C1
_____
▼M22
02007L0046 — EN — 18.01.2018 — 021.001 — 337

14A Protection of the driver against the steering Regulation (EC) No 661/2009 N/A N/A
mechanism in the event of impact UNECE Regulation No 12
▼M6
▼C1
_____
▼M22
15A Seats, their anchorages and any head restraints Regulation (EC) No 661/2009 X D (4B) D (4B) D D D
15B Seats of large passenger vehicles Regulation (EC) No 661/2009 D D

▼M22
▼M6
▼C1
_____
▼M22
16A External projections Regulation (EC) No 661/2009 A

▼M6
▼C1
_____
▼M22
17A Vehicle access and manoeuvrability Regulation (EC) No 661/2009 X X X X X X

02007L0046 — EN — 18.01.2018 — 021.001 — 338

17B Speedometer equipment including its instal Regulation (EC) No 661/2009 X X X X X X
lation UNECE Regulation No 39
▼M6
▼C1
_____
▼M22
18A Manufacturer’s statutory plate and vehicle Regulation (EC) No 661/2009 X X X X X X X X X X

identification number Regulation (EU) No 19/2011
▼M6
▼C1
_____
▼M22
19A Safety-belt anchorages, Isofix anchorages Regulation (EC) No 661/2009 A A A A A A

systems and Isofix top tether anchorages UNECE Regulation No 14
▼M6
▼C1
_____
▼M22
20A Installation of lighting and light-signalling Regulation (EC) No 661/2009 A+N A+N A+N A+N A+N A+N A+N A+N A+N A+N
devices on vehicles UNECE Regulation No 48
▼M6
▼C1
_____
▼M22
02007L0046 — EN — 18.01.2018 — 021.001 — 339

21A Retro-reflecting devices for power-driven Regulation (EC) No 661/2009 X X X X X X X X X X
vehicles and their trailers UNECE Regulation No 3
▼M6
▼C1
_____
▼M22
22A Front and rear position lamps, stop-lamps and Regulation (EC) No 661/2009 X X X X X X X X X X
end-ouline marker lamps for motor vehicles UNECE Regulation No 7
and their trailers
22B Daytime running lamps for power-driven Regulation (EC) No 661/2009 X X X X X X

▼M22
22C Side-marker lamps for motor vehicles and Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
_____
▼M22
23A Direction indicators for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X X X X X

▼M6
▼C1
_____
▼M22
02007L0046 — EN — 18.01.2018 — 021.001 — 340

24A Illumination of rear-registration plates of Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
_____
▼M22
25A Power-driven vehicle’s sealed-beam Regulation (EC) No 661/2009 X X X X X X

headlamps (SB) emitting an European asym UNECE Regulation No 31
metrical passing beam or a driving beam or
both
25B Filament lamps for use in approved lamp units Regulation (EC) No 661/2009 X X X X X X X X X X
of power-driven vehicles and their trailers UNECE Regulation No 37
▼M22
25C Motor vehicle headlamps equipped with Regulation (EC) No 661/2009 X X X X X X

gas-discharge light sources UNECE Regulation No 98
25D Gas-discharge light sources for use in Regulation (EC) No 661/2009 X X X X X X

approved gas-discharge lamp units of UNECE Regulation No 99
power-driven vehicles
25E Motor vehicle headlamps emitting an asym Regulation (EC) No 661/2009 X X X X X X

metrical passing beam or a driving beam or UNECE Regulation No 112
both and equipped with filament lamps and/or
LED modules
25F Adaptive front-lighting systems (AFS) for Regulation (EC) No 661/2009 X X X X X X

motor vehicles UNECE Regulation No 123
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 341

▼M22
26A Power-driven vehicle front fog lamps Regulation (EC) No 661/2009 X X X X X X

▼M6
▼C1
_____
▼M22
27A Towing device Regulation (EC) No 661/2009 A A A A A A

▼M22
▼M6
▼C1
_____
▼M22
28A Rear fog lamps for power-driven vehicles and Regulation (EC) No 661/2009 X X X X X X X X X X
▼M6
▼C1
_____
▼M22
29A Reversing lights for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X X X X X

02007L0046 — EN — 18.01.2018 — 021.001 — 342

▼M6
▼C1
_____
▼M22
30A Parking lamps for power-driven vehicles Regulation (EC) No 661/2009 X X X X X X

▼M6
▼C1
_____
▼M22
31A Safety-belts, restraint systems, child restraint Regulation (EC) No 661/2009 A A A A A A

systems and Isofix child restraint systems UNECE Regulation No 16
▼M22
▼M6
▼C1
_____
▼M22
32A Forward field of vision Regulation (EC) No 661/2009 S

▼M6
▼C1
_____
▼M22
33A Location and identification of hand controls, Regulation (EC) No 661/2009 X X X X X X

tell-tales and indicators UNECE Regulation No 121
02007L0046 — EN — 18.01.2018 — 021.001 — 343

▼M6
▼C1
_____
▼M22
34A Windscreen defrosting and demisting systems Regulation (EC) No 661/2009 A (5) (5) (5) (5) (5)
▼M6
▼C1
_____
▼M22
35A Windscreen wiper and washer systems Regulation (EC) No 661/2009 A (6) (6) (6) (6) (6)
▼M22
▼M6
▼C1
_____
▼M22
36A Heating systems Regulation (EC) No 661/2009 X X X X X X X X X X

▼M6
▼C1
_____
▼M22
37A Wheel guards Regulation (EC) No 661/2009 X

02007L0046 — EN — 18.01.2018 — 021.001 — 344

▼M6
▼C1
_____
▼M22
38A Head restraints (headrests), whether or not Regulation (EC) No 661/2009 X

incorporated in vehicle seats UNECE Regulation No 25
41 Emissions (Euro IV and V) heavy duty Directive 2005/55/EC A (8) X (8) X X (8) X (8) X
vehicles.
41A Emissions (Euro VI) heavy duty vehicles/ Regulation (EC) No 595/2009 X (9) X (9) X X (9) X (9) X
access to information
▼M22
▼M6
▼C1
_____
▼M22
42A Lateral protection of goods vehicles Regulation (EC) No 661/2009 X X X X

▼M6
▼C1
_____
▼M22
43A Spray suppression systems Regulation (EC) No 661/2009 X X X X X X X

02007L0046 — EN — 18.01.2018 — 021.001 — 345

▼M6
▼C1
_____
▼M22
44A Masses and dimensions Regulation (EC) No 661/2009 X

▼M6
▼C1
_____
▼M22
45A Safety glazing materials and their installation Regulation (EC) No 661/2009 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A
on vehicles UNECE Regulation No 43
▼M22
▼M6
_____
▼M22
46A Installation of tyres Regulation (EC) No 661/2009 A A A A A A A A A A

46B Pneumatic tyres for motor vehicles and their Regulation (EC) No 661/2009 A A A A
trailers (Class C1) UNECE Regulation No 30
46C Pneumatic tyres for commercial vehicles and Regulation (EC) No 661/2009 A A A A A A A
their trailers (Classes C2 and C3) UNECE Regulation No 54
46D Tyre rolling sound emissions, adhesion on wet Regulation (EC) No 661/2009 A A A A A A A A A A
surfaces and rolling resistance (Classes C1, UNECE Regulation No 117
C2 and C3)
02007L0046 — EN — 18.01.2018 — 021.001 — 346

46E Temporary-use spare unit, run-flat tyres/ Regulation (EC) No 661/2009 A (9A) A (9A)
system and tyre pressure monitoring system UNECE Regulation No 64
▼M6
▼C1
_____
▼M22
47A Speed limitation of vehicles Regulation (EC) No 661/2009 X X X X

▼M6
▼C1
_____
▼M22
48A Masses and dimensions Regulation (EC) No 661/2009 X X X X X X X X X

▼M6
▼C1
_____
▼M22
49A Commercial vehicles with regard to their Regulation (EC) No 661/2009 A A A

external projections forward of the cab’s rear UNECE Regulation No 61
panel
▼M6
▼C1
_____
▼M22
02007L0046 — EN — 18.01.2018 — 021.001 — 347

50A Mechanical coupling components of combi Regulation (EC) No 661/2009 X (10) X (10) X (10) X (10) X (10) X (10) X X X X
nations of vehicles UNECE Regulation No 55
50B Close-coupling device (CCD); fitting of an Regulation (EC) No 661/2009 X (10) X (10) X (10) X (10)
approved type of CCD UNECE Regulation No 102
▼M6
▼C1
_____
▼M22
51A Burning behaviour of materials used in the Regulation (EC) No 661/2009 X

interior construction of certain categories of UNECE Regulation No 118
motor vehicles
▼M22
▼M6
▼C1
_____
▼M22
52A M2 and M3 vehicles Regulation (EC) No 661/2009 A A

52B Strength of the superstructure of large Regulation (EC) No 661/2009 A A

passenger vehicles UNECE Regulation No 66
▼M6
▼C1
_____
▼M22
02007L0046 — EN — 18.01.2018 — 021.001 — 348

53A Protection of occupants in the event of a Regulation (EC) No 661/2009 N/A
frontal collision UNECE Regulation No 94
▼M6
▼C1
_____
▼M22
54A Protection of occupants in the event of lateral Regulation (EC) No 661/2009 N/A N/A
▼M6
▼C1
_____
▼M22
56A Vehicles for the carriage of dangerous goods Regulation (EC) No 661/2009 X (13) X (13) X (13) X (13) X (13) X (13) X (13)
▼M6
▼C1
_____
▼M22
57A Front underrun protective devices (FUPDs) Regulation (EC) No 661/2009 X X

and their installation; front underrun UNECE Regulation No 93
protection (FUP)
58 Pedestrian protection Regulation (EC) No 78/2009 N/A N/A
59 Recyclability Directive 2005/64/EC N/A N/A —
02007L0046 — EN — 18.01.2018 — 021.001 — 349

60 (empty)
61 Air-conditioning systems Directive 2006/40/EC X X (14)
62 Hydrogen system Regulation (EC) No 79/2009 A A A A A A
63 General Safety Regulation (EC) No 661/2009 X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15)
64 Gear shift indicators Regulation (EC) No 661/2009 X

65 Advanced emergency braking system Regulation (EC) No 661/2009 (16) (16) (16) (16)
▼M22
66 Lane departure warning system Regulation (EC) No 661/2009 (17) (17) (17) (17)
67 Specific components for liquefied petroleum Regulation (EC) No 661/2009 X X X X X X

gases (LPG) and their installation on motor UNECE Regulation No 67
vehicles
68 Vehicle alarm systems (VAS) Regulation (EC) No 661/2009 X X

69 Electrical safety Regulation (EC) No 661/2009 X X X X X X

70 Specific components for CNG and their instal Regulation (EC) No 661/2009 X X X X X X
lation on motor vehicules UNECE Regulation No 110
02007L0046 — EN — 18.01.2018 — 021.001 — 350

02007L0046 — EN — 18.01.2018 — 021.001 — 351
▼M22
Appendix 3
Wheel-chair Accessible Vehicles
Item Subject Regulatory act M1
1 Permissible sound level Directive 70/157/EEC G+W0
▼M26
1A Sound level Regulation (EU) G + W9

No 540/2014
▼M22
2 Emissions (Euro 5 and 6) light duty vehicles/ Regulation (EC) No 715/ G+W1
access to information 2007
▼M6
▼C1
_____
▼M22
3A Prevention of fire risks (liquid fuel tanks) Regulation (EC) No 661/ X+W2
2009
UNECE Regulation
No 34
3B Rear underrun protective devices (RUPDs) and Regulation (EC) No 661/ X

their installation; rear underrun protection (RUP) 2009
UNECE Regulation
No 58
▼M6
▼C1
_____
▼M22
4A Space for mounting and fixing rear registration Regulation (EC) No 661/ X
plates 2009
Regulation (EU)
No 1003/2010
▼M6
▼C1
_____
▼M22
5A Steering equipment Regulation (EC) No 661/ G

2009
UNECE Regulation
No 79
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 352
▼M22
6A Vehicle access and manoeuvrability Regulation (EC) No 661/ X

2009
Regulation (EU)
No 130/2012
6B Door latches and door retention components Regulation (EC) No 661/ X

2009
UNECE Regulation
No 11
▼M6
▼C1
_____
▼M22
7A Audible warning devices and signals Regulation (EC) No 661/ X

2009
UNECE Regulation
No 28
▼M6
▼C1
_____
▼M22
8A Devices for indirect vision and their installation Regulation (EC) No 661/ X
2009
UNECE Regulation
No 46
▼M6
▼C1
_____
▼M22
9B Braking of passenger cars Regulation (EC) No 661/ G+A1

2009
UNECE Regulation
No 13-H
▼M6
▼C1
_____
▼M22
10A Electromagnetic compatibility Regulation (EC) No 661/ X

2009
UNECE Regulation
No 10
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 353
▼M22
12A Interior fittings Regulation (EC) No 661/ G+C

2009
UNECE Regulation
No 21
▼M6
▼C1
_____
▼M22
13B Protection of motor vehicles against unauthorised Regulation (EC) No 661/ X

use 2009
UNECE Regulation
No 116
▼M6
▼C1
_____
▼M22
14A Protection of the driver against the steering Regulation (EC) No 661/ G
mechanism in the event of impact 2009
UNECE Regulation
No 12
▼M6
▼C1
_____
▼M22
15A Seats, their anchorages and any head restraints Regulation (EC) No 661/ G+W3
2009
UNECE Regulation
No 17
▼M6
▼C1
_____
▼M22
16A External projections Regulation (EC) No 661/ G+W4

2009
UNECE Regulation
No 26
▼M6
▼C1
_____
▼M22

2009
Regulation (EU)
No 130/2012
02007L0046 — EN — 18.01.2018 — 021.001 — 354
▼M22
17B Speedometer equipment including its installation Regulation (EC) No 661/ X

2009
UNECE Regulation
No 39
▼M6
▼C1
_____
▼M22
18A Manufacturer’s statutory plate and vehicle identi Regulation (EC) No 661/ X
fication number 2009
Regulation (EU) No 19/
2011
▼M6
▼C1
_____
▼M22
19A Safety-belt anchorages, Isofix anchorages systems Regulation (EC) No 661/ X+W5
and Isofix top tether anchorages 2009
UNECE Regulation
No 14
▼M6
▼C1
_____
▼M22
20A Installation of lighting and light-signalling Regulation (EC) No 661/ X

devices on vehicles 2009
UNECE Regulation
No 48
▼M6
▼C1
_____
▼M22
21A Retro-reflecting devices for power-driven vehicles Regulation (EC) No 661/ X

UNECE Regulation
No 3
▼M6
▼C1
_____
▼M22
22A Front and rear position lamps, stop-lamps and Regulation (EC) No 661/ X
end-ouline marker lamps for motor vehicles and 2009
their trailers UNECE Regulation
No 7
02007L0046 — EN — 18.01.2018 — 021.001 — 355
▼M22
22B Daytime running lamps for power-driven vehicles Regulation (EC) No 661/ X
2009
UNECE Regulation
No 87
22C Side-marker lamps for motor vehicles and their Regulation (EC) No 661/ X
trailers 2009
UNECE Regulation
No 91
▼M6
▼C1
_____
▼M22
23A Direction indicators for power-driven vehicles Regulation (EC) No 661/ X

UNECE Regulation
No 6
▼M6
▼C1
_____
▼M22
24A Illumination of rear-registration plates of Regulation (EC) No 661/ X

power-driven vehicles and their trailers 2009
UNECE Regulation
No 4
▼M6
▼C1
_____
▼M22
25A Power-driven vehicle’s sealed-beam Regulation (EC) No 661/ X

headlamps (SB) emitting an European asym 2009
metrical passing beam or a driving beam or both UNECE Regulation
No 31
25B Filament lamps for use in approved lamp units of Regulation (EC) No 661/ X
UNECE Regulation
No 37
25C Motor vehicle headlamps equipped with Regulation (EC) No 661/ X

gas-discharge light sources 2009
UNECE Regulation
No 98
25D Gas-discharge light sources for use in approved Regulation (EC) No 661/ X
gas-discharge lamp units of power-driven 2009
vehicles UNECE Regulation
No 99
02007L0046 — EN — 18.01.2018 — 021.001 — 356
▼M22
25E Motor vehicle headlamps emitting an asym Regulation (EC) No 661/ X

metrical passing beam or a driving beam or 2009
both and equipped with filament lamps and/or UNECE Regulation
LED modules No 112
25F Adaptive front-lighting systems (AFS) for motor Regulation (EC) No 661/ X
vehicles 2009
UNECE Regulation
No 123
▼M6
▼C1
_____
▼M22
26A Power-driven vehicle front fog lamps Regulation (EC) No 661/ X

2009
UNECE Regulation
No 19
▼M6
▼C1
_____
▼M22
27A Towing device Regulation (EC) No 661/ E

2009
Regulation (EU)
No 1005/2010
▼M6
▼C1
_____
▼M22
28A Rear fog lamps for power-driven vehicles and Regulation (EC) No 661/ X
their trailers 2009
UNECE Regulation
No 38
▼M6
▼C1
_____
▼M22
29A Reversing lights for power-driven vehicles and Regulation (EC) No 661/ X
their trailers 2009
UNECE Regulation
No 23
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 357
▼M22
30A Parking lamps for power-driven vehicles Regulation (EC) No 661/ X

2009
UNECE Regulation
No 77
▼M6
▼C1
_____
▼M22
31A Safety-belts, restraint systems, child restraint Regulation (EC) No 661/ X+W6
systems and Isofix child restraint systems 2009
UNECE Regulation
No 16
▼M6
▼C1
_____
▼M22
32A Forward field of vision Regulation (EC) No 661/ G

2009
UNECE Regulation
No 125
▼M6
▼C1
_____
▼M22
33A Location and identification of hand controls, Regulation (EC) No 661/ X

tell-tales and indicators 2009
UNECE Regulation
No 121
▼M6
▼C1
_____
▼M22
34A Windscreen defrosting and demisting systems Regulation (EC) No 661/ G(5)
2009
Regulation (EU)
No 672/2010
▼M6
▼C1
_____
▼M22
35A Windscreen wiper and washer systems Regulation (EC) No 661/ G(6)
2009
Regulation (EU)
No 1008/2010
02007L0046 — EN — 18.01.2018 — 021.001 — 358
▼M22
▼M6
▼C1
_____
▼M22
36A Heating systems Regulation (EC) No 661/ X

2009
UNECE Regulation
No 122
▼M6
▼C1
_____
▼M22
37A Wheel guards Regulation (EC) No 661/ G

2009
Regulation (EU)
No 1009/2010
38 Head restraints Directive 78/932/EEC X
38A Head restraints (headrests), whether or not incor Regulation (EC) No 661/ X
porated in vehicle seats 2009
UNECE Regulation
No 25
41 Emissions (Euro IV and V) heavy duty vehicles. Directive 2005/55/EC X+W1 (8)
41A Emissions (Euro VI) heavy duty vehicles/access Regulation (EC) No 595/ X+W1 (9)
to information 2009
▼M6
▼C1
_____
▼M22
44A Masses and dimensions Regulation (EC) No 661/ X+W8

2009
Regulation (EU)
No 1230/2012
▼M6
▼C1
_____
▼M22
45A Safety glazing materials and their installation on Regulation (EC) No 661/ G
vehicles 2009
UNECE Regulation
No 43
02007L0046 — EN — 18.01.2018 — 021.001 — 359
▼M22
▼M6
_____
▼M22
46A Installation of tyres Regulation (EC) No 661/ X

2009
Regulation (EU)
No 458/2011
46B Pneumatic tyres for motor vehicles and their Regulation (EC) No 661/ X
trailers (Class C1) 2009
UNECE Regulation
No 30
46D Tyre rolling sound emissions, adhesion on wet Regulation (EC) No 661/ X
surfaces and rolling resistance (Classes C1, C2 2009
and C3) UNECE Regulation
No 117
46E Temporary-use spare unit, run-flat tyres/system Regulation (EC) No 661/ G(9A)
and tyre pressure monitoring system 2009
UNECE Regulation
No 64
▼M6
▼C1
_____
▼M22
50A Mechanical coupling components of combi Regulation (EC) No 661/ X(10)

nations of vehicles 2009
UNECE Regulation
No 55
▼M6
▼C1
_____
▼M22
53A Protection of occupants in the event of a frontal Regulation (EC) No 661/ N/A
collision 2009
UNECE Regulation
No 94
▼M6
▼C1
_____
▼M22
54A Protection of occupants in the event of lateral Regulation (EC) No 661/ N/A
collision 2009
UNECE Regulation
No 95
58 Pedestrian protection Regulation (EC) No 78/ G

2009
02007L0046 — EN — 18.01.2018 — 021.001 — 360
▼M22
59 Recyclability Directive 2005/64/EC N/A
61 Air-conditioning systems Directive 2006/40/EC G
62 Hydrogen system Regulation (EC) No 79/ X

2009
63 General Safety Regulation (EC) No 661/ X(15)

2009
64 Gear shift indicators Regulation (EC) No 661/ G

2009
2012
67 Specific components for liquefied petroleum Regulation (EC) No 661/ X

gases (LPG) and their installation on motor 2009
No 67
68 Vehicle alarm systems (VAS) Regulation (EC) No 661/ X

2009
UNECE Regulation
No 97
69 Electric safety Regulation (EC) No 661/ X

2009
UNECE Regulation
No 100
70 Specific components for CNG and their instal Regulation (EC) No 661/ X
lation on motor vehicules 2009
UNECE Regulation
No 110
Additional requirements for testing the wheelchair tie down and occupant
restraint system
Note: The following sections 1. and either section 2. or 3. shall apply.
0. Definitions
0.1. Surrogate wheelchair (SWC) is a rigid, re-usable test wheelchair, as
defined in section 3 of ISO 10542-1:2012.
0.2. Point P is a representation of the position of the wheelchair occupant's hip

when seated in the SWC, as defined in section 3 of ISO 10542-1:2012.
1. General requirements
1.1. Each wheelchair location shall be provided with anchorages to which a
wheelchair tie-down and occupant restraint system (WTORS) shall be
fitted.
1.2. The wheelchair occupant’s lower belt anchorages shall be located in

accordance with UNECE Regulation 14-07, paragraph 5.4.2.2, relative
to Point P on the SWC when placed in the travelling position designated
by the manufacturer. The upper actual anchorage (s) shall be located at
least 1 100 mm above the horizontal plane passing through the points of
contact between the rear tyres of the SWC and the vehicle floor. This
condition shall still be satisfied after the test carried out according to
paragraph 2. below.
02007L0046 — EN — 18.01.2018 — 021.001 — 361
▼M22
1.3. An assessment shall be made of the WTORS occupant belt to ensure
compliance with the provisions of UNECE Regulation 16-06 paragraphs
8.2.2 to 8.2.2.4 and 8.3.1 to 8.3.4.
1.4. The minimum number of ISOFIX child seat anchorages need not to be
provided. In the case of a multi-stage approval where an ISOFIX
anchorage system has been affected by the conversion, the system shall
either be re-tested or the anchorages shall be rendered unusable. In the
latter case the ISOFIX labels shall be removed and appropriate
information given to the vehicle purchaser.
2. Static in-vehicle testing

2.1. Wheelchair occupant restraint anchorages
2.1.1. The wheelchair occupant restraint anchorages shall resist the static forces
prescribed for occupant restraint anchorages in UNECE Regulation 14-07
simultaneously with the static forces applied to the wheelchair tie-down
anchorages as specified in 2.2 below.
2.2. Wheelchair tie-down anchorages

The wheelchair tie-down anchorages shall resist the following forces, for
at least 0.2 seconds, applied via the SWC (or a suitable surrogate
wheelchair having a wheelbase, seat height and tie-down attachment
points in accordance with the specification for the SWC), at a height
of 300 +/– 100 mm from the surface on which the SWC rests:
2.2.1. In the case of a forward-facing wheelchair, a simultaneous force,

coincident with the force applied to the occupant restraint anchorages,
of 24,5 kN and
2.2.2. a second test applying a static force of 8,2 kN directed towards the rear of
the vehicle.
2.2.3. In the case of a rearward-facing wheelchair, a simultaneous force,

coincident with the force applied to the occupant restraint anchorages,
of 8,2 kN and
2.2.4. a second test applying a static force of 24,5 kN directed towards the front
of the vehicle.
2.3. Components of the system

2.3.1. All components of the WTORS shall meet the relevant requirements of
ISO 10542-1:2012. However, the dynamic test specified in Annex A and
paragraphs 5.2.2 and 5.2.3 of ISO 10542-1:2012 shall be carried out on
the complete WTORS using the vehicle anchorage geometry instead of the
test geometry specified in Annex A of ISO 10542-1:2012. This may be
carried out within the vehicle structure or on a surrogate structure repre
sentative of the vehicle’s WTORS anchorage geometry. The location of
each anchorage shall lie within the tolerance provided for in point 7.7.1 of
UNECE Regulation No 16-06.
2.3.2. Where the occupant restraint part of the WTORS is approved according to
UNECE Regulation No 16-06, it shall be subject to the dynamic test of
the complete WTORS specified in paragraph 2.3.1, but the requirements
of Paragraphs 5.1, 5.3 and 5.4 of ISO10542-1:2012 shall be considered to
have been met.
02007L0046 — EN — 18.01.2018 — 021.001 — 362
▼M22
3. Dynamic in-vehicle testing
3.1. The full assembly of the WTORS system shall be tested by an in-vehicle
dynamic test in line with paragraphs 5.2.2 and 5.2.3 and Annex A of ISO
10542-1:2012, testing all components/anchorages simultaneously, using a
vehicle body-in-white or representative structure.
3.2. The component parts of the WTORS shall meet the relevant requirements
of ISO10542-1:2012 paragraphs 5.1, 5.3 and 5.4. These requirements shall
be deemed to have been met in respect of the occupant restraint if it is
approved according to UNECE Regulation No 16-06.
02007L0046 — EN — 18.01.2018 — 021.001 — 363
▼M22
Appendix 4
Other Special Purpose Vehicles (including special group, multi-equipment

carrier and trailer Caravans)
The requirements of Annex IV shall be fulfilled to the greatest extent: Appli

cation of the exemptions is only permitted if the manufacturer demonstrates to
the satisfaction of the approval authority that the vehicle, due to the special
function, cannot meet all the requirements.
Reference to
Item Subject M2 M3 N1 N2 N3 O1 O2 O3 O4
regulatory act
1 Permissible Directive 70/ H H H H H

sound level 157/EEC
▼M23
1A Sound level Regulation H H H H H

(EU) No 540/
2014
▼M22
2 Emissions Regulation Q(1) Q+ Q+

(Euro 5 and 6) (EC) No 715/ V1 (1) V1 (1)
light duty 2007
vehicles/access
to information
▼M6
▼C1
_____
▼M22
3A Prevention of Regulation F F F F F X X X X
fire risks (liquid (EC) No 661/
fuel tanks) 2009
UNECE
Regulation
No 34
3B Rear underrun Regulation X X A A A X X X X

protective (EC) No 661/
devices 2009
(RUPDs) and UNECE
their instal Regulation
lation; rear No 58
underrun
protection
(RUP)
▼M6
▼C1
_____
▼M22
4A Space for Regulation A+R A+R A+R A+R A+R A+R A+R A+R A+R
mounting and (EC) No 661/
fixing rear 2009
registration Regulation
plates (EU)
No 1003/2010
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 364
▼M22
Reference to
regulatory act
5A Steering Regulation X X X X X X X X X
2009
UNECE
Regulation
No 79
▼M6
▼C1
_____
▼M22
6A Vehicle access Regulation X X B B B

and manoeuvr (EC) No 661/
ability 2009
Regulation
(EU) No 130/
2012
6B Door latches Regulation B

and door (EC) No 661/
retention 2009
components UNECE
Regulation
No 11
▼M6
▼C1
_____
▼M22
7A Audible Regulation X X X X X
warning devices (EC) No 661/
and signals 2009
UNECE
Regulation
No 28
▼M6
▼C1
_____
▼M22
8A Devices for Regulation X X X X X

indirect vision (EC) No 661/
and their instal 2009
lation UNECE
Regulation
No 46
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 365
▼M22
Reference to
regulatory act
9A Braking of Regulation X (3) X (3) X (3) X+ X+ X X X (3) X (3)

vehicles and (EC) No 661/ U1 (3) U1 (3)
trailers 2009
UNECE
Regulation
No 13
9B Braking of Regulation X (4)

passenger cars (EC) No 661/
2009
UNECE
Regulation
No 13-H
▼M6
▼C1
_____
▼M22
10A Electromagnetic Regulation X X X X X X X X X

compatibility (EC) No 661/
2009
UNECE
Regulation
No 10
▼M6
▼C1
_____
▼M22
13A Protection of Regulation X (4A) X (4A) X (4A) X (4A)

motor vehicles (EC) No 661/
against unauth 2009
orised use UNECE
Regulation
No 18
13B Protection of Regulation X

motor vehicles (EC) No 661/
against unauth 2009
orised use UNECE
Regulation
No 116
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 366
▼M22
Reference to
regulatory act
14A Protection of Regulation X

the driver (EC) No 661/
against the 2009
steering UNECE
mechanism in Regulation
the event of No 12
impact
▼M6
▼C1
_____
▼M22
15A Seats, their Regulation D (4B) D (4B) D D D

anchorages and (EC) No 661/
any head 2009
restraints UNECE
Regulation
No 17
15B Seats of large Regulation D D

passenger (EC) No 661/
vehicles 2009
UNECE
Regulation
No 80
▼M6
▼C1
_____
▼M22
17A Vehicle access Regulation X X X X X

and manoeuvr (EC) No 661/
ability 2009
Regulation
(EU) No 130/
2012
17B Speedometer Regulation X X X X X

including its 2009
installation UNECE
Regulation
No 39
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 367
▼M22
Reference to
regulatory act
18A Manufacturer’s Regulation X X X X X X X X X

statutory plate (EC) No 661/
and vehicle 2009
identification Regulation
number (EU) No 19/
2011
▼M6
▼C1
_____
▼M22
19A Safety-belt Regulation D D D D D

anchorages, (EC) No 661/
Isofix 2009
anchorages UNECE
systems and Regulation
Isofix top tether No 14
anchorages
▼M6
▼C1
_____
▼M22
20A Installation of Regulation A+N A+N A+N A+N A+N A+N A+N A+N A+N
lighting and (EC) No 661/
light-signalling 2009
devices on UNECE
vehicles Regulation
No 48
▼M6
▼C1
_____
▼M22
21A Retro-reflecting Regulation X X X X X X X X X

devices for (EC) No 661/
power-driven 2009
vehicles and UNECE
their trailers Regulation
No 3
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 368
▼M22
Reference to
regulatory act
22A Front and rear Regulation X X X X X X X X X

position lamps, (EC) No 661/
stop-lamps and 2009
end-ouline UNECE
marker lamps Regulation
for motor No 7
vehicles and
their trailers
22B Daytime Regulation X X X X X

running lamps (EC) No 661/
for 2009
power-driven UNECE
vehicles Regulation
No 87
22C Side-marker Regulation X X X X X X X X X

lamps for motor (EC) No 661/
vehicles and 2009
their trailers UNECE
Regulation
No 91
▼M6
▼C1
_____
▼M22
23A Direction Regulation X X X X X X X X X

indicators for (EC) No 661/
power-driven 2009
vehicles and UNECE
No 6
▼M6
▼C1
_____
▼M22
24A Illumination of Regulation X X X X X X X X X

rear-registration (EC) No 661/
plates of 2009
power-driven UNECE
vehicles and Regulation
their trailers No 4
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 369
▼M22
Reference to
regulatory act
25A Power-driven Regulation X X X X X

vehicle’s (EC) No 661/
sealed-beam 2009
headlamps (SB) UNECE
emitting an Regulation
European No 31
asymmetrical
passing beam or
a driving beam
or both
25B Filament lamps Regulation X X X X X X X X X

for use in (EC) No 661/
approved lamp 2009
units of UNECE
power-driven Regulation
vehicles and No 37
their trailers
25C Motor vehicle Regulation X X X X X

equipped with 2009
gas-discharge UNECE
light sources Regulation
No 98
25D Gas-discharge Regulation X X X X X

light sources for (EC) No 661/
use in approved 2009
gas-discharge UNECE
lamp units of Regulation
power-driven No 99
vehicles
25E Motor vehicle Regulation X X X X X

emitting an 2009
asymmetrical UNECE
passing beam or Regulation
a driving beam No 112
or both and
equipped with
filament lamps
and/or LED
modules
25F Adaptive Regulation X X X X X

front-lighting (EC) No 661/
systems (AFS) 2009
for motor UNECE
vehicles Regulation
No 123
02007L0046 — EN — 18.01.2018 — 021.001 — 370
▼M22
Reference to
regulatory act
▼M6
▼C1
_____
▼M22
26A Power-driven Regulation X X X X X

vehicle front (EC) No 661/
fog lamps 2009
UNECE
Regulation
No 19
▼M6
▼C1
_____
▼M22
27A Towing device Regulation A A A A A

(EC) No 661/
2009
Regulation
(EU)
No 1005/2010
▼M6
▼C1
_____
▼M22
28A Rear fog lamps Regulation X X X X X X X X X

for (EC) No 661/
power-driven 2009
vehicles and UNECE
No 38
▼M6
▼C1
_____
▼M22
29A Reversing lights Regulation X X X X X X X X X

for (EC) No 661/
power-driven 2009
vehicles and UNECE
No 23
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 371
▼M22
Reference to
regulatory act
30A Parking lamps Regulation X X X X X

for (EC) No 661/
power-driven 2009
vehicles UNECE
Regulation
No 77
▼M6
▼C1
_____
▼M22
31A Safety-belts, Regulation D D D D D

restraint (EC) No 661/
systems, child 2009
restraint UNECE
systems and Regulation
Isofix child No 16
restraint
systems
▼M6
▼C1
_____
▼M22
33A Location and Regulation X X X X X

identification of (EC) No 661/
hand controls, 2009
tell-tales and UNECE
indicators Regulation
No 121
▼M6
▼C1
_____
▼M22
34A Windscreen Regulation (5) (5) (5) (5) (5)

defrosting and (EC) No 661/
demisting 2009
systems Regulation
(EU) No 672/
2010
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 372
▼M22
Reference to
regulatory act
35A Windscreen Regulation (6) (6) (6) (6) (6)

wiper and (EC) No 661/
washer systems 2009
Regulation
(EU)
No 1008/2010
▼M6
▼C1
_____
▼M22
36A Heating Regulation X X X X X X X X X

systems (EC) No 661/
2009
UNECE
Regulation
No 122
▼M24
_____
▼M22
41 Emissions Directive H (8) H H (8) H (8) H

(Euro IV and 2005/55/EC
V) heavy duty
vehicles.
41A Emissions Regulation H (9) H H (9) H (9) H

(Euro VI) (EC) No 595/
heavy duty 2009
vehicles/access
to information
▼M6
▼C1
_____
▼M22
42A Lateral Regulation X X X X

protection of (EC) No 661/
goods vehicles 2009
UNECE
Regulation
No 73
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 373
▼M22
Reference to
regulatory act
43A Spray Regulation X X X X X X X

suppression (EC) No 661/
systems 2009
Regulation
(EU) No 109/
2011
▼M6
▼C1
_____
▼M22
45A Safety glazing Regulation J J J J J J J J J

materials and (EC) No 661/
their installation 2009
on vehicles UNECE
Regulation
No 43
▼M6
_____
▼M22
46A Installation of Regulation X X X X X X X X X

tyres (EC) No 661/
2009
Regulation
(EU) No 458/
2011
46B Pneumatic tyres Regulation X X X

for motor (EC) No 661/
vehicles and 2009
(Class C1) Regulation
No 30
46C Pneumatic tyres Regulation X X X X X X X

for commercial (EC) No 661/
vehicles and 2009
(Classes C2 and Regulation
C3) No 54
46D Tyre rolling Regulation X X X X X X X X X

sound (EC) No 661/
emissions, 2009
adhesion on wet UNECE
surfaces and Regulation
rolling No 117
resistance
(Classes C1, C2
and C3)
02007L0046 — EN — 18.01.2018 — 021.001 — 374
▼M22
Reference to
regulatory act
46E Temporary-use Regulation X (9A)

spare unit, (EC) No 661/
run-flat tyres/ 2009
system and tyre UNECE
pressure moni Regulation
toring system No 64
▼M6
▼C1
_____
▼M22
47A Speed limitation Regulation X X X X

of vehicles (EC) No 661/
2009
UNECE
Regulation
No 89
▼M6
▼C1
_____
▼M22
48A Masses and Regulation X X X X X X X X X

dimensions (EC) No 661/
2009
Regulation
(EU)
No 1230/2012
▼M6
▼C1
_____
▼M22
49A Commercial Regulation X X X

vehicles with (EC) No 661/
regard to their 2009
external UNECE
projections Regulation
forward of the No 61
cab’s rear panel
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 375
▼M22
Reference to
regulatory act
50A Mechanical Regulation X (10) X (10) X (10) X (10) X (10) X X X X

coupling (EC) No 661/
components of 2009
combinations of UNECE
vehicles Regulation
No 55
50B Close-coupling Regulation X (10) X (10) X (10) X (10)

device (CCD); (EC) No 661/
fitting of an 2009
approved type UNECE
of CCD Regulation
No 102
▼M6
▼C1
_____
▼M22
51A Burning Regulation X

behaviour of (EC) No 661/
materials used 2009
in the interior UNECE
construction of Regulation
certain No 118
categories of
motor vehicles
▼M6
▼C1
_____
▼M22
52A M2 and M3 Regulation X X

vehicles (EC) No 661/
2009
UNECE
Regulation
No 107
52B Strength of the Regulation X X

superstructure (EC) No 661/
of large 2009
passenger UNECE
vehicles Regulation
No 66
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 376
▼M22
Reference to
regulatory act
54A Protection of Regulation A

event of lateral 2009
collision UNECE
Regulation
No 95
▼M6
▼C1
_____
▼M22
56A Vehicles for the Regulation X (13) X (13) X (13) X (13) X (13) X (13) X (13)
carriage of (EC) No 661/
dangerous 2009
goods UNECE
Regulation
No 105
▼M6
▼C1
_____
▼M22
57A Front underrun Regulation X X

protective (EC) No 661/
devices 2009
(FUPDs) and UNECE
their instal Regulation
lation; front No 93
underrun
protection
(FUP)
58 Pedestrian Regulation N/
protection (EC) No 78/ A (*)
2009
59 Recyclability Directive N/A —

2005/64/EC
61 Air-condi Directive X (14)

tioning systems 2006/40/EC
62 Hydrogen Regulation X X X X X
system (EC) No 79/
2009
63 General Safety Regulation X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15) X (15)
(EC) No 661/
2009
02007L0046 — EN — 18.01.2018 — 021.001 — 377
▼M22
Reference to
regulatory act
65 Advanced Regulation N/A N/A N/A N/A

emergency (EC) No 661/
braking system 2009
Regulation
(EU) No 347/
2012
66 Lane departure Regulation N/A N/A N/A N/A

warning system (EC) No 661/
2009
Regulation
(EU) No 351/
2012
67 Specific Regulation X X X X X
liquefied 2009
petroleum UNECE
gases (LPG) Regulation
and their instal No 67
lation on motor
vehicles
68 Vehicle alarm Regulation X

systems (VAS) (EC) No 661/
2009
UNECE
Regulation
No 97
69 Electric safety Regulation X X X X X

(EC) No 661/
2009
UNECE
Regulation
No 100
70 Specific Regulation X X X X X
CNG and their 2009
installation on UNECE
motor vehicules Regulation
No 110
(*) Any frontal protection system supplied with the vehicle shall comply with the requirements of Regulation (EC) No 78/2009 and
shall be provided with a type-approval number and shall be marked accordingly.
02007L0046 — EN — 18.01.2018 — 021.001 — 378
▼M22
Appendix 5
Mobile Cranes
Item Subject Reference to regulatory act N3
1 Permissible sound level Directive 70/157/EEC T+Z1
▼M26
1A Sound level Regulation (EU) T + Z1

No 540/2014
▼M6
▼C1
_____
▼M22
3A Prevention of fire risks (liquid fuel tanks) Regulation (EC) No 661/ X

2009
UNECE Regulation
No 34
3B Rear underrun protective devices (RUPDs) and Regulation (EC) No 661/ A

their installation; rear underrun protection (RUP) 2009
UNECE Regulation
No 58
▼M6
▼C1
_____
▼M22
4A Space for mounting and fixing rear registration Regulation (EC) No 661/ X
plates 2009
Regulation (EU)
No 1003/2010
▼M6
▼C1
_____
▼M22
5A Steering equipment Regulation (EC) No 661/ X

2009 Crab steering allowed
UNECE Regulation
No 79
▼M6
▼C1
_____
▼M22
6A Vehicle access and manoeuvrability Regulation (EC) No 661/ A

2009
Regulation (EU)
No 130/2012
02007L0046 — EN — 18.01.2018 — 021.001 — 379
▼M22
▼M6
▼C1
_____
▼M22
7A Audible warning devices and signals Regulation (EC) No 661/ X

2009
UNECE Regulation
No 28
▼M6
▼C1
_____
▼M22
8A Devices for indirect vision and their installation Regulation (EC) No 661/ X
2009
UNECE Regulation
No 46
▼M6
▼C1
_____
▼M22
9A Braking of vehicles and trailers Regulation (EC) No 661/ U (3)

2009
UNECE Regulation
No 13
▼M6
▼C1
_____
▼M22
10A Electromagnetic compatibility Regulation (EC) No 661/ X

2009
UNECE Regulation
No 10
▼M6
▼C1
_____
▼M22
13A Protection of motor vehicles against unauthorised Regulation (EC) No 661/ X (4A)
use 2009
UNECE Regulation
No 18
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 380
▼M22
15A Seats, their anchorages and any head restraints Regulation (EC) No 661/ X
2009
UNECE Regulation
No 17
▼M6
▼C1
_____
▼M22

2009
Regulation (EU)
No 130/2012
17B Speedometer equipment including its installation Regulation (EC) No 661/ X

2009
UNECE Regulation
No 39
▼M6
▼C1
_____
▼M22
18A Manufacturer’s statutory plate and vehicle identi Regulation (EC) No 661/ X
fication number 2009
2011
▼M6
▼C1
_____
▼M22
19A Safety-belt anchorages, Isofix anchorages systems Regulation (EC) No 661/ X

and Isofix top tether anchorages 2009
UNECE Regulation
No 14
▼M6
▼C1
_____
▼M22
20A Installation of lighting and light-signalling Regulation (EC) No 661/ A+Y

devices on vehicles 2009
UNECE Regulation
No 48
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 381
▼M22
21A Retro-reflecting devices for power-driven vehicles Regulation (EC) No 661/ X

UNECE Regulation
No 3
▼M6
▼C1
_____
▼M22
22A Front and rear position lamps, stop-lamps and Regulation (EC) No 661/ X
end-ouline marker lamps for motor vehicles and 2009
their trailers UNECE Regulation
No 7
22B Daytime running lamps for power-driven vehicles Regulation (EC) No 661/ X
2009
UNECE Regulation
No 87
22C Side-marker lamps for motor vehicles and their Regulation (EC) No 661/ X
trailers 2009
UNECE Regulation
No 91
▼M6
▼C1
_____
▼M22
23A Direction indicators for power-driven vehicles Regulation (EC) No 661/ X

UNECE Regulation
No 6
▼M6
▼C1
_____
▼M22
24A Illumination of rear-registration plates of Regulation (EC) No 661/ X

UNECE Regulation
No 4
▼M6
▼C1
_____
▼M22
25A Power-driven vehicle’s sealed-beam Regulation (EC) No 661/ X

headlamps (SB) emitting an European asym 2009
metrical passing beam or a driving beam or both UNECE Regulation
No 31
02007L0046 — EN — 18.01.2018 — 021.001 — 382
▼M22
25B Filament lamps for use in approved lamp units of Regulation (EC) No 661/ X
UNECE Regulation
No 37
25C Motor vehicle headlamps equipped with Regulation (EC) No 661/ X

gas-discharge light sources 2009
UNECE Regulation
No 98
25D Gas-discharge light sources for use in approved Regulation (EC) No 661/ X
gas-discharge lamp units of power-driven 2009
No 99
25E Motor vehicle headlamps emitting an asym Regulation (EC) No 661/ X

metrical passing beam or a driving beam or 2009
both and equipped with filament lamps and/or UNECE Regulation
LED modules No 112
25F Adaptive front-lighting systems (AFS) for motor Regulation (EC) No 661/ X
vehicles 2009
UNECE Regulation
No 123
▼M6
▼C1
_____
▼M22
26A Power-driven vehicle front fog lamps Regulation (EC) No 661/ X

2009
UNECE Regulation
No 19
▼M6
▼C1
_____
▼M22
27A Towing device Regulation (EC) No 661/ A

2009
Regulation (EU)
No 1005/2010
▼M6
▼C1
_____
▼M22
28A Rear fog lamps for power-driven vehicles and Regulation (EC) No 661/ X
their trailers 2009
UNECE Regulation
No 38
▼M6
▼C1
_____
02007L0046 — EN — 18.01.2018 — 021.001 — 383
▼M22
29A Reversing lights for power-driven vehicles and Regulation (EC) No 661/ X
their trailers 2009
UNECE Regulation
No 23
▼M6
▼C1
_____
▼M22
30A Parking lamps for power-driven vehicles Regulation (EC) No 661/ X

2009
UNECE Regulation
No 77
▼M6
▼C1
_____
▼M22
31A Safety-belts, restraint systems, child restraint Regulation (EC) No 661/ X

systems and Isofix child restraint systems 2009
UNECE Regulation
No 16
▼M6
▼C1
_____
▼M22
33A Location and identification of hand controls, Regulation (EC) No 661/ X

tell-tales and indicators 2009
UNECE Regulation
No 121
▼M6
▼C1
_____
▼M22
34A Windscreen defrosting and demisting systems Regulation (EC) No 661/ (5)
2009
Regulation (EU)
No 672/2010
▼M6
▼C1
_____
▼M22
35A Windscreen wiper and washer systems Regulation (EC) No 661/ (6)
2009
Regulation (EU)
No 1008/2010
02007L0046 — EN — 18.01.2018 — 021.001 — 384
▼M22
▼M6
▼C1
_____
▼M22
36A Heating systems Regulation (EC) No 661/ X

2009
UNECE Regulation
No 122
41 Emissions (Euro IV and V) heavy duty vehicles. Directive 2005/55/EC V
41A Emissions (Euro VI) heavy duty vehicles/access Regulation (EC) No 595/ V
to information 2009
▼M6
▼C1
_____
▼M22
42A Lateral protection of goods vehicles Regulation (EC) No 661/ A

2009
UNECE Regulation
No 73
▼M6
▼C1
_____
▼M22
43A Spray suppression systems Regulation (EC) No 661/ Z1

2009
Regulation (EU)
No 109/2011
▼M6
▼C1
_____
▼M22
45A Safety glazing materials and their installation on Regulation (EC) No 661/ J
vehicles 2009
UNECE Regulation
No 43
▼M6
_____
▼M22
46A Installation of tyres Regulation (EC) No 661/ X

2009
Regulation (EU)
No 458/2011
02007L0046 — EN — 18.01.2018 — 021.001 — 385
▼M22
46C Pneumatic tyres for commercial vehicles and their Regulation (EC) No 661/ X
trailers (Classes C2 and C3) 2009
UNECE Regulation
No 54
46D Tyre rolling sound emissions, adhesion on wet Regulation (EC) No 661/ X
surfaces and rolling resistance (Classes C1, C2 2009
and C3) UNECE Regulation
No 117
▼M6
▼C1
_____
▼M22
47A Speed limitation of vehicles Regulation (EC) No 661/ X

2009
UNECE Regulation
No 89
▼M6
▼C1
_____
▼M22
48A Masses and dimensions Regulation (EC) No 661/ A

2009
Regulation (EU)
No 1230/2012
▼M6
▼C1
_____
▼M22
49A Commercial vehicles with regard to their external Regulation (EC) No 661/ A
projections forward of the cab’s rear panel 2009
UNECE Regulation
No 61
▼M6
▼C1
_____
▼M22
50A Mechanical coupling components of combi Regulation (EC) No 661/ X (10)

nations of vehicles 2009
UNECE Regulation
No 55
50B Close-coupling device (CCD); fitting of an Regulation (EC) No 661/ X (10)

approved type of CCD 2009
UNECE Regulation
No 102
02007L0046 — EN — 18.01.2018 — 021.001 — 386
▼M22
▼M6
▼C1
_____
▼M22
57A Front underrun protective devices (FUPDs) and Regulation (EC) No 661/ X
their installation; front underrun protection (FUP) 2009
UNECE Regulation
No 93
62 Hydrogen system Regulation (EC) No 79/ X

2009
63 General Safety Regulation (EC) No 661/ X (15)

2009
65 Advanced emergency braking system Regulation (EC) No 661/ N/A (16)

2009
Regulation (EU)
No 347/2012
66 Lane departure warning system Regulation (EC) No 661/ N/A (17)

2009
Regulation (EU)
No 351/2012
67 Specific components for liquefied petroleum Regulation (EC) No 661/ X

gases (LPG) and their installation on motor 2009
No 67
69 Electric safety Regulation (EC) No 661/ X

2009
UNECE Regulation
No 100
70 Specific components for CNG and their instal Regulation (EC) No 661/ X
lation on motor vehicules 2009
UNECE Regulation
No 110
02007L0046 — EN — 18.01.2018 — 021.001 — 387
▼M22
Appendix 6
Exceptional load transport vehicles
Item Subject Reference to regulatory act N3 O4
1 Permissible sound level Directive 70/157/EEC T
3 Fuel tanks/rear protective devices Directive 70/221/EEC X (2) X
3A Prevention of fire risks (liquid Regulation (EC) No 661/2009 X X

fuel tanks) UNECE Regulation No 34
3B Rear underrun protective devices Regulation (EC) No 661/2009 A A

(RUPDs) and their installation; UNECE Regulation No 58
rear underrun protection (RUP)
4 Rear registration plate space Directive 70/222/EEC X A+R
4A Space for mounting and fixing Regulation (EC) No 661/2009 X A+R

rear registration plates Regulation (EU) No 1003/2010
5 Steering effort Directive 70/311/EEC X X

Crab
steering
allowed
5A Steering equipment Regulation (EC) No 661/2009 X X

UNECE Regulation No 79 Crab
steering
allowed
6 Door latches and hinges Directive 70/387/EEC X
6A Vehicle access and manoeuvr Regulation (EC) No 661/2009 X

ability Regulation (EU) No 130/2012
7 Audible warning Directive 70/388/EEC X
7A Audible warning devices and Regulation (EC) No 661/2009 X

signals UNECE Regulation No 28
8 Indirect vision devices Directive 2003/97/EC X
8A Devices for indirect vision and Regulation (EC) No 661/2009 X

their installation UNECE Regulation No 46
9 Braking Directive 71/320/EEC U X

02007L0046 — EN — 18.01.2018 — 021.001 — 388
▼M22
9A Braking of vehicles and trailers Regulation (EC) No 661/2009 U (3) X (3)

10 Radio interference (electrom Directive 72/245/EEC X X

agnetic compatibility)
10A Electromagnetic compatibility Regulation (EC) No 661/2009 X X

13 Anti-theft and immobiliser Directive 74/61/EEC X
13A Protection of motor vehicles Regulation (EC) No 661/2009 X (4A)

against unauthorised use UNECE Regulation No 18
15 Seat strength Directive 74/408/EEC X
15A Seats, their anchorages and any Regulation (EC) No 661/2009 X

head restraints UNECE Regulation No 17
17 Speedometer and reverse gear Directive 75/443/EEC X
17A Vehicle access and manoeuvr Regulation (EC) No 661/2009 X

ability Regulation (EU) No 130/2012
17B Speedometer equipment including Regulation (EC) No 661/2009 X

its installation UNECE Regulation No 39
18 Statutory plates Directive 76/114/EEC X X
18A Manufacturer’s statutory plate and Regulation (EC) No 661/2009 X X

vehicle identification number Regulation (EU) No 19/2011
19 Seat belt anchorages Directive 76/115/EEC X
19A Safety-belt anchorages, Isofix Regulation (EC) No 661/2009 X

anchorages systems and Isofix UNECE Regulation No 14
top tether anchorages
20 Installation of lighting and light Directive 76/756/EEC X A+N

signalling devices
20A Installation of lighting and Regulation (EC) No 661/2009 X A+N

light-signalling devices on UNECE Regulation No 48
vehicles
21 Retro reflectors Directive 76/757/EEC X X

02007L0046 — EN — 18.01.2018 — 021.001 — 389
▼M22
21A Retro-reflecting devices for Regulation (EC) No 661/2009 X X

power-driven vehicles and their UNECE Regulation No 3
trailers
22 End-outline, front-position (side), Directive 76/758/EEC X X

rear-position (side), stop, side
marker, daytime running lamps
22A Front and rear position lamps, Regulation (EC) No 661/2009 X X

stop-lamps and end-ouline UNECE Regulation No 7
marker lamps for motor vehicles
and their trailers
22B Daytime running lamps for Regulation (EC) No 661/2009 X

power-driven vehicles UNECE Regulation No 87
22C Side-marker lamps for motor Regulation (EC) No 661/2009 X X

23 Direction indicators Directive 76/759/EEC X X
23A Direction indicators for Regulation (EC) No 661/2009 X X

power-driven vehicles and their UNECE Regulation No 6
trailers
24 Rear registration plate lamps Directive 76/760/EEC X X
24A Illumination of rear-registration Regulation (EC) No 661/2009 X X

plates of power-driven vehicles UNECE Regulation No 4
and their trailers
25 Headlamps (including bulbs) Directive 76/761/EEC X
25A Power-driven vehicle’s Regulation (EC) No 661/2009 X

sealed-beam headlamps (SB) UNECE Regulation No 31
emitting an European asym
metrical passing beam or a
driving beam or both
25B Filament lamps for use in Regulation (EC) No 661/2009 X X

approved lamp units of UNECE Regulation No 37
power-driven vehicles and their
trailers
25C Motor vehicle headlamps Regulation (EC) No 661/2009 X

equipped with gas-discharge light UNECE Regulation No 98
sources
25D Gas-discharge light sources for Regulation (EC) No 661/2009 X

use in approved gas-discharge UNECE Regulation No 99
lamp units of power-driven
vehicles
02007L0046 — EN — 18.01.2018 — 021.001 — 390
▼M22
25E Motor vehicle headlamps emitting Regulation (EC) No 661/2009 X

an asymmetrical passing beam or UNECE Regulation No 112
a driving beam or both and
equipped with filament lamps
and/or LED modules
25F Adaptive front-lighting systems Regulation (EC) No 661/2009 X

(AFS) for motor vehicles UNECE Regulation No 123
26 Front fog lamps Directive 76/762/EEC X
26A Power-driven vehicle front fog Regulation (EC) No 661/2009 X

lamps UNECE Regulation No 19
27 Towing hooks Directive 77/389/EEC A
27A Towing device Regulation (EC) No 661/2009 A

28 Rear fog lamps Directive 77/538/EEC X X
28A Rear fog lamps for power-driven Regulation (EC) No 661/2009 X X

29 Reversing lamps Directive 77/539/EEC X X
29A Reversing lights for power-driven Regulation (EC) No 661/2009 X X

30 Parking lamps Directive 77/540/EEC X
30A Parking lamps for power-driven Regulation (EC) No 661/2009 X

31 Seat belts and restraint systems Directive 77/541/EEC X
31A Safety-belts, restraint systems, Regulation (EC) No 661/2009 X

child restraint systems and Isofix UNECE Regulation No 16
child restraint systems
33 Identification of controls, tell-tales Directive 78/316/EEC X

and indicators
33A Location and identification of Regulation (EC) No 661/2009 X

hand controls, tell-tales and UNECE Regulation No 121
indicators
02007L0046 — EN — 18.01.2018 — 021.001 — 391
▼M22
34 Defrost/demist Directive 78/317/EEC (5)
34A Windscreen defrosting and Regulation (EC) No 661/2009 (5)

demisting systems Regulation (EU) No 672/2010
35 Wash/wipe Directive 78/318/EEC (6)
35A Windscreen wiper and washer Regulation (EC) No 661/2009 (6)

systems Regulation (EU) No 1008/2010
36 Heating systems Directive 2001/56/EC X
36A Heating systems Regulation (EC) No 661/2009 X

41 Emissions (Euro IV and V) heavy Directive 2005/55/EC X (8)

duty vehicles.
41A Emissions (Euro VI) heavy duty Regulation (EC) No 595/2009 X (9)
vehicles/access to information
42 Lateral protection Directive 89/297/EEC X A
42A Lateral protection of goods Regulation (EC) No 661/2009 X A

43 Spray-suppression systems Directive 91/226/EEC X A
43A Spray suppression systems Regulation (EC) No 661/2009 X A

45 Safety glazing Directive 92/22/EEC X
45A Safety glazing materials and their Regulation (EC) No 661/2009 X

installation on vehicles UNECE Regulation No 43
46 Tyres Directive 92/23/EEC X I
46A Installation of tyres Regulation (EC) No 661/2009 X I

46C Pneumatic tyres for commercial Regulation (EC) No 661/2009 X I

(Classes C2 and C3)
02007L0046 — EN — 18.01.2018 — 021.001 — 392
▼M22
46D Tyre rolling sound emissions, Regulation (EC) No 661/2009 X I

adhesion on wet surfaces and UNECE Regulation No 117
rolling resistance (Classes C1,
C2 and C3)
47 Speed limitation devices Directive 92/24/EEC X
47A Speed limitation of vehicles Regulation (EC) No 661/2009 X

48 Masses and dimensions (other Directive 97/27/EC X X

than vehicles referred to in item
44)
48A Masses and dimensions Regulation (EC) No 661/2009 A A

49 External projections of cabs Directive 92/114/EEC A
49A Commercial vehicles with regard Regulation (EC) No 661/2009 A

to their external projections UNECE Regulation No 61
forward of the cab’s rear panel
50 Couplings Directive 94/20/EC X (10) X
50A Mechanical coupling components Regulation (EC) No 661/2009 X(10) X

of combinations of vehicles UNECE Regulation No 55
50B Close-coupling device (CCD); Regulation (EC) No 661/2009 X(10) X(10)

fitting of an approved type of UNECE Regulation No 102
CCD
56 Vehicles intended for the transport Directive 98/91/EC X (13) X(13)

of dangerous goods
56A Vehicles for the carriage of Regulation (EC) No 661/2009 X(13) X(13)
dangerous goods UNECE Regulation No 105
57 Front underrun protection Directive 2000/40/EC A
57A Front underrun protective devices Regulation (EC) No 661/2009 A

(FUPDs) and their installation; UNECE Regulation No 93
front underrun protection (FUP)
62 Hydrogen system Regulation (EC) No 79/2009 X
63 General Safety Regulation (EC) No 661/2009 X (15) X(15)

02007L0046 — EN — 18.01.2018 — 021.001 — 393
▼M22
65 Advanced emergency braking Regulation (EC) No 661/2009 N/A (16)

system Regulation (EU) No 347/2012
66 Lane departure warning system Regulation (EC) No 661/2009 N/A (17)

67 Specific components for liquefied Regulation (EC) No 661/2009 X

petroleum gases (LPG) and their UNECE Regulation No 67
installation on motor vehicles
69 Electric safety Regulation (EC) No 661/2009 X

70 Specific components for CNG and Regulation (EC) No 661/2009 X

their installation on motor UNECE Regulation No 110
vehicules
Meaning of notes:
X The requirements of the relevant act are applicable. The series of amendments of the UNECE Regulations which applies on a
compulsory basis are listed in Annex IV to Regulation (EC) No 661/2009. Series of amendments adopted subsequently are
accepted as an alternative. Member States may grant extensions to existing type-approvals granted according to the former EU
Directives repealed by Regulation (EC) 661/2009 under the conditions fixed by Article 13(14) of Regulation (EC) 661/2009.
N/A This regulatory act is not applicable to this vehicle (no requirements).
(1) For vehicles with a reference mass not exceeding 2 610 kg. At the manufacturer’s request, may apply to vehicles with a reference
mass not exceeding 2 840 kg. With regard to Access to information, for other parts (e.g. living compartment) than the base vehicle,
it is sufficient that the manufacturer provide access to repair and maintenance information in a readily accessible and prompt
manner.
(2) In case of vehicles equipped with a LPG or CNG installation, a vehicle type-approval in accordance with UNECE Regulation
No 67 or UNECE Regulation No 110 is required.
(3) The fitting of an ESC system is required in accordance with Article 12 of Regulation (EC) No 661/2009. The implementation dates
set out in Annex V to Regulation (EC) No 661/2009 apply. In accordance with UNECE Regulation 13, the fitting of an electronic
stability control (‘ESC’) system is not required for special purpose vehicles of categories M2, M3, N2 and N3 and for vehicles for
exceptional load transport and trailers with areas for standing passengers. N1 vehicles may be approved according to UNECE
Regulation 13 or UNECE Regulation 13-H.
(4) The fitting of an ESC system is required in accordance with Article 12 of Regulation (EC) No 661/2009. Therefore, the
requirements set out in Part A of Annex 9 to UNECE Regulation No 13-H shall be complied with for the purposes of EC
type-approval of new types of vehicles as well as for the registration, sale and entry into service of new vehicles. The implemen
tation dates set out in Article 13 of Regulation (EC) No 661/2009 apply. N1 vehicles may be approved according to UNECE
Regulation 13 or UNECE Regulation 13-H.
(4A) If fitted, the protective device shall fulfill the requirements of UNECE Regulation No 18.
(4B) This Regulation applies to seats not falling within the scope of UNECE Regulation No 80.
For other options, see Article 2 of Regulation (EC) No 595/2009.
(5) Vehicles of categories other than M1 do not need to fully comply with act but shall be fitted with a suitable windscreen defrosting
and demisting device.
(6) Vehicles of categories other than M1 do not need to fully comply with act but shall be fitted with a suitable windscreen washing
and wiping devices.
(8) For vehicles with a reference mass exceeding 2 610 kg and which did not benefit from the possibility offered in note (1).
02007L0046 — EN — 18.01.2018 — 021.001 — 394
▼M22
(9) For vehicles with a reference mass exceeding 2 610 kg which are not type-approved (at the manufacturer’s request and provided
their reference mass does not exceed 2 840 kg) under Regulation (EC) No 715/2007. For other parts than the base vehicle, it is
sufficient that the manufacturer provide access to repair and maintenance information in a readily accessible and prompt manner
(9A) Applies only where such vehicles are fitted with equipment covered by UNECE Regulation No 64. Tyre pressure monitoring
system for M1 vehicles applies on a compulsory basis in accordance with Article 9(2) of Regulation (EC) No 661/2009.
(10) Applies only to vehicles equipped with coupling(s).
(11) Applies to vehicles with a technically permissible maximum laden mass not exceeding 2,5 tonnes.
(12) Only applicable to vehicles where the ‘Seating Reference Point (“R” point)’ of the lowest seat is not more than 700 mm above the
ground level.
(13) Applies only when the manufacturer applies for type-approval of vehicles intended for the transport of dangerous goods.
(14) Applies only for vehicles of category N1, class I (reference mass ≤ 1 305 kg)
(15) At the request of the manufacturer, a type-approval may be granted under this item, as an alternative to obtaining type-approvals
under each individual item covered by Regulation (EC) No 661/2009.
(16) The fitting of an Advanced emergency braking system is not required for special purpose vehicles in accordance with Article 1 of
Regulation (EU) No 347/2012.
(17) The fitting of a Lane departure warning system is not required for special purpose vehicles in accordance with Article 1 of
Regulation (EU) No 351/2012.
A The requirements shall be fulfilled to the greatest extent. The type-approval authority may only grant exemption(s) if the manu
facturer demonstrates that the vehicle cannot meet the requirements due to its special purpose. The exemptions granted shall be
described on the vehicle type-approval certificate and the certificate of conformity (remark –entry 52).
A1 The fitting of ESC is not mandatory. In the case of multi-stage approvals, where the modifications made at a particular stage are
likely to affect the function of the base vehicle’s ESC system, the manufacturer may either disable the system or demonstrate that
the vehicle has not been rendered unsafe or unstable. This may be demonstrated, e.g., by performing rapid double lane-change
manoeuvres in each direction at 80 km/h with sufficient severity to cause intervention by the ESC system. These interventions shall
be well-controlled and shall act to improve stability of the vehicle. The Technical Service shall have the right to request further
testing if deemed necessary.
B Application limited to doors giving access to the seats designated for normal use when the vehicle is travelling on the road and
where the distance between the R point of the seat and the average plane of the door surface, measured perpendicular to the
longitudinal medium plane of the vehicle, does not exceed 500 mm.
C Application limited to that part of the vehicle in front of the rearmost seat designated for normal use when the vehicle is travelling
on the road and also limited to the head impact zone as defined in the legal act.
D Application limited to seats designated for normal use when the vehicle is travelling on the road. Seats which are not designated for
use when the vehicle is travelling on the road shall be clearly identified to users either by means of a pictogram or a sign with an
appropriate text. The luggage retention requirements of UNECE Regulations No. 17 shall not apply.
E Front only.
F Modification to the routing and length of the refuelling duct and re-positioning of the tank inboard is permissible.
G In case of multi-stage approval, requirements according to the category of the base/incomplete vehicle (e.g. the chassis of which
was used to build the special purpose vehicle) may also be used.
H Modification of exhaust system length after the last silencer not exceeding 2 m is permissible without any further test.
I Tyres shall be type-approved according to the requirements of UNECE Regulation No. 54 even if the design speed of the vehicle is
less than 80 km/h. The load capacity may be adjusted in relation to the maximum design speed of the trailer in agreement with the
tyre manufacturer.
J For all window glazing other than driver's cab glazing (windshield and side glasses), the material may be either of safety glass or
rigid plastic glazing.
02007L0046 — EN — 18.01.2018 — 021.001 — 395
▼M22
K Additional panic alarm devices permitted.
L Application limited to seats designated for normal use when the vehicle is travelling on the road. At least anchorages for lap belts
are required in the rear seating positions. Seats which are not designated for use when the vehicle is travelling on the road shall be
clearly identified to users either by means of a pictogram or a sign with an appropriate text. ISOFIX is not required on Ambulances
and hearses.
M Application limited to seats designated for normal use when the vehicle is travelling on the road. At least lap belts are required in
all rear seating positions. Seats which are not designated for use when the vehicle is travelling on the road shall be clearly identified
to users either by means of a pictogram or a sign with an appropriate text. ISOFIX is not required on Ambulances and hearses.
N Provided that all mandatory lighting devices are installed and that the geometric visibility is not affected.
Q Modification of exhaust system length after the last silencer not exceeding 2 m is permissible without any further test. An EC
type-approval issued to the most representative base vehicle remains valid irrespective of change in the reference weight.
R Provided that the registration plates of all Member States can be mounted and remain visible.
S The light transmission factor is at least 60 %, also the ‘A’ pillar obstruction angle is not more than 10o.
T Test to be performed only with the complete/completed vehicle. The vehicle can be tested according to Directive 70/157/EEC.
Concerning item 5.2.2.1 of Annex I to Directive 70/157/EEC the following limit values are applicable:
(a) 81 dB(A) for vehicles with an engine power of less than 75 kW;
(b) 83 dB(A) for vehicles with an engine power of not less than 75 kW but less than 150 kW;
(c) 84 dB(A) for vehicles with an engine power of not less than 150 kW.
U Test to be performed only with the complete/completed vehicle. Vehicles up to 4 axles shall comply with all the requirements laid
down by regulatory act. Derogations are admitted for vehicles having more than 4 axles, provided that:
— they are justified by the particular construction
— all the braking performances, related to parking, service and secondary braking laid down by the regulatory act are fulfilled.
U1 ABS is not mandatory for vehicles with hydrostatic drive.
V As alternative, Directive 97/68/EC may also be applied.
V1 For vehicles with hydrostatic drive, Directive 97/68/EC may also be aplied as alternative.
W0 Modification of exhaust system length is permitted without any further test, provided the back pressure is similar. If a new test is
required, an extra 2dB(A) above the applicable limit shall be allowed.
W1 Requirements shall be complied with, but modification in the exhaust system is permitted without any further test of tailpipe
emissions and CO2/fuel consumption provided the emission control devices including particulate filters (if any) are not affected.
No new evaporative test shall be required on the modified vehicle on condition that the evaporative control devices are kept as
fitted by the manufacturer of the base vehicle.
An EC type approval issued to the most representative base vehicle remains valid irrespective of change in the reference mass.
W2 Modification of the routing, length of the refuelling duct, fuel hoses and fuel vapour pipes is permitted without further test.
Re-location of the original fuel tank is permitted provided all requirements are met. However further testing according to Annex 5
to UNECE Regulation No. 34 shall not be required.
W3 The longitudinal plane of the intended wheelchair-travelling position shall be parallel to the longitudinal plane of the vehicle.
Appropriate information shall be made available to the vehicle owner that, in order to be capable of withstanding the forces
transmitted by the tie-down mechanism during the various driving conditions, a wheelchair with a structure meeting the relevant
part of ISO 7176-19:2008 is recommended.
Appropriate adaptations may be made to the seats of the vehicle without further testing provided if it can be demonstrated to the
technical service that their anchorages, mechanisms and head restraints provide the same level of performance.
The luggage retention requirements of UNECE Regulation No. 17 shall not apply.
02007L0046 — EN — 18.01.2018 — 021.001 — 396
▼M22
W4 Compliance with the legal act(s) shall be required for the boarding aids when in the resting position.
W5 Each wheelchair location shall be provided with anchorages to which a wheelchair tie-down and occupant restraint
system (WTORS) shall be fitted, and which comply with the additional provisions of Appendix 3.
W6 Each wheelchair location shall be provided with occupant restraint belt that comply with the additional provisions of Appendix 3
When, due to the conversion, anchorage points for the safety belts need to be moved outside the tolerance provided for in
point 7.7.1 of UNECE Regulation No.16-06, the technical service shall check whether the alteration constitutes a worst case or
not. If that is the case, the test provided for in point 7.7.1. of UNECE Regulation No.16-06 shall be performed. Extension to the
EC type-approval does not need to be issued. The test may be performed using components that have not undergone the
conditioning test prescribed by UNECE Regulation No.16-06.
W8 For the purposes of calculations, the mass of the wheel-chair including the user shall be assumed to be 160 kg. The mass shall be
concentrated at the P point of the surrogate wheelchair in its travelling position declared by the manufacturer.
Any limitation in the passenger capacity resulting from the use of wheelchair(s) shall be recorded in the owner’s handbook, on side
2 of the EU type-approval certificate and in the the certificate of conformity (remark section).
►M26 W9 Modification of the exhaust system length is permitted without the need for retesting, provided that the exhaust back
pressure characteristics remain similar. ◄
Y Provided that all mandatory lighting devices are installed.
Z The requirements on the protrusion of open windows shall not apply to the living compartment.
Z1 Mobile cranes with more than six axles are considered to be off-road vehicles (N3G) when at least three axles are driven and
provided they meet the provisions of Annex II, point 4.3 b) ii) and iii) as well as point 4.3 c).
02007L0046 — EN — 18.01.2018 — 021.001 — 397
▼M22
ANNEX XII
SMALL SERIES AND END-OF-SERIES LIMITS
A. SMALL SERIES LIMITS

1. The number of units of one type of vehicle to be registered, sold or put
into service per year in the European Union pursuant to Article 22 may
not exceed the figures shown below for the vehicle category in question:
Category Units
M1 1 000
M2 , M3 0
N1 1 000
N2 , N3 0
O1 , O2 0
O3 , O4 0

into service per year in one Member State pursuant to Article 23 shall be
determined by that Member State but shall not exceed the figures shown
below for the vehicle category in question:
Category Units
M1 100
M2 , M3 250
N1 500 until 31October 2016
250 from 1 November 2016
N2 , N3 250
O1 , O2 500
O3 , O4 250

into service per year in one Member State for the purposes of Article 6(2)
of Commission Regulation (EU) No 1230/2012 shall be determined by
each Member State but shall not exceed the figures shown below for the
vehicle category in question:
Category Units
M2 , M3 1 000
N2 , N3 1 200
O3 , O4 2 000
B. END-OF-SERIES LIMITS
The maximum number of complete and completed vehicles put into service
in each Member State under the procedure ‘End-of-Series’ shall be restricted
in one of the following ways to be chosen by the Member State:
1. The maximum number of vehicles of one or more types may not exceed
10 %, in the case of category M1, and may not exceed 30 % of the
vehicles of all types concerned put into service in that Member State
during the previous year, in the case of all other categories.
02007L0046 — EN — 18.01.2018 — 021.001 — 398
▼M22
Should 10 %, respectively 30 %, be less than 100 vehicles, then the
Member State may allow the putting into service of a maximum of 100
vehicles.
2. Vehicles of any one type shall be restricted to those for which a valid
certificate of conformity was issued on or after the date of manufacture
and which remained valid for at least three months after its date of issue
but subsequently lost its validity due to the entry into force of a regu
latory act.
02007L0046 — EN — 18.01.2018 — 021.001 — 399
▼B
ANNEX XIII
LIST OF PARTS OR EQUIPMENT WHICH ARE CAPABLE OF POSING A SIGNIFICANT RISK TO THE
CORRECT FUNCTIONING OF SYSTEMS THAT ARE ESSENTIAL FOR THE SAFETY OF THE VEHICLE
OR ITS ENVIRONMENTAL PERFORMANCE, THEIR PERFORMANCE REQUIREMENTS,
APPROPRIATE TEST PROCEDURES, MARKING AND PACKAGING PROVISIONS
I. Parts or equipment having a significant impact on vehicle safety
Item No Item description Performance Test procedure Marking Packaging

requirement requirement requirements
1 […]
2
3
II. Parts or equipment having a significant impact on the environmental performance of the vehicle
Item No Item description Performance Test procedure Marking Packaging

requirement requirement requirements
1 […]
2
3
02007L0046 — EN — 18.01.2018 — 021.001 — 400
▼B
ANNEX XIV
LIST OF EC TYPE-APPROVALS ISSUED PURSUANT TO

REGULATORY ACTS
Type-approval authority stamp
List number:
Covering the period: … to …
The following information in respect of each EC type-approval granted, refused

or withdrawn in the above mentioned period must be given:
Manufacturer:
Reason for extension (where applicable):
Make:
Type:
Date of issue:
First date of issue (in the case of extensions):

02007L0046 — EN — 18.01.2018 — 021.001 — 401
▼M9
ANNEX XV
REGULATORY ACTS FOR WHICH A MANUFACTURER MAY BE

DESIGNATED AS TECHNICAL SERVICE

0.1. This Annex lays down the list of the regulatory acts for which a manu
facturer may be designated as technical service in accordance with
Article 41(6).
0.2. It also includes appropriate provisions concerning the designation of a

manufacturer as technical service, to be applied in the framework of the
type-approval of vehicles, components and separate technical units
concerned by Part I of Annex IV.
0.3. However it does not apply to manufacturers which apply for small series
approval in accordance with Article 22.
1. Appointment of a manufacturer as technical service

1.1. A manufacturer appointed as technical service is a manufacturer who has
been designated by the approval authority as a testing laboratory to carry
out approval tests on its behalf in the meaning of point 31 of Article 3.
In accordance with Article 41(6), a manufacturer may only be designated as

technical service for category A activities.
1.2. The expression ‘to carry out test’ is not restricted to the measurement of
performances but covers also the registration of test results and the
submission of a report to the approval authority including the relevant
conclusions.
It covers the checking of compliance with those provisions which do not

necessarily require measurement. This is the case for the assessment of the
design against legislative requirements.
For example, ‘check compliance of the location of the fuel tank in a vehicle
with the provisions of point 5.10 of Annex I to Directive 70/221/EEC’ has
to be understood as part of ‘to carry out test’.
▼M26
2. List of regulatory acts and restrictions
Subject Regulatory act reference
4 Rear registration plate space Directive 70/222/EEC
4A Space for mounting and fixing rear registration Regulation (EC) No 661/2009
plates
7 Audible warning Directive 70/388/EEC
7A Audible warning devices and signals Regulation (EC) No 661/2009

10 Radio interference (electromagnetic compatibility) Directive 72/245/EEC
10A Electromagnetic compatibility Regulation (EC) No 661/2009

18 Plates (statutory) Directive 76/114/EEC
18A Manufacturer's statutory plate and vehicle identi Regulation (EC) No 661/2009
fication number
02007L0046 — EN — 18.01.2018 — 021.001 — 402
▼M26
20 Installation of lighting and light signalling devices Directive 76/756/EEC
20A Installation of lighting and light-signalling devices Regulation (EC) No 661/2009

on vehicles
27 Towing hooks Directive 77/389/EEC
27A Towing device Regulation (EC) No 661/2009

33 Identification of controls, tell-tales and indicators Directive 78/316/EEC
33A Location and identification of hand controls, Regulation (EC) No 661/2009

tell-tales and indicators
34 Defrost/demist Directive 78/317/EEC
34A Windscreen defrosting and demisting systems Regulation (EC) No 661/2009

35 Wash/wipe Directive 78/318/EEC
35A Windscreen wiper and washer systems Regulation (EC) No 661/2009

36 Heating systems Directive 2001/56/EC

Except the provisions in Annex VIII relating to
LPG combustion heaters and LPG heating systems
36A Heating systems Regulation (EC) No 661/2009

Except the provisions in Annex 8 relating to LPG
combustion heaters and LPG heating systems
37 Wheel guards Directive 78/549/EEC
37A Wheel guards Regulation (EC) No 661/2009

44 Masses and dimensions (cars) Directive 92/21/EEC
44A Masses and dimensions Regulation (EC) No 661/2009

45 Safety glazing Directive 92/22/EEC

Restricted to the provisions included in Annex III
45A Safety glazing materials and their installation on Regulation (EC) No 661/2009
vehicles
Restricted to the provisions included in Annex 21
02007L0046 — EN — 18.01.2018 — 021.001 — 403
▼M26
▼M6
_____
▼M26
46A Installation of tyres Regulation (EC) No 661/2009

▼M30
46B Rolling resistance determination Regulation (EU) 2017/2400, Annex X
▼M26
48 Masses and dimensions (other than vehicles Directive 97/27/EC

referred to in item 44)

49 External projections of cabs Directive 92/114/EEC
49A Commercial vehicles with regard to their external Regulation (EC) No 661/2009
projections forward of the cab's rear panel
50 Couplings Directive 94/20/EC

Restricted to the provisions included in Annex V
(up to and including point 8) and Annex VII
50A Mechanical coupling components of combinations Regulation (EC) No 661/2009

of vehicles
Restricted to the provisions included in Annex 5
(up to and including paragraph 8) and Annex 7
61 Air-conditioning system Directive 2006/40/EC

02007L0046 — EN — 18.01.2018 — 021.001 — 404
▼M9
Appendix
Designation of a manufacturer as technical service
1. General
1.1. The designation and notification of a manufacturer as technical service shall
be made in accordance with the provisions of Articles 41, 42 and 43 as well
with the practical measures included in this Appendix.
1.2. The manufacturer shall be accredited under Standard EN ISO/IEC

17025:2005 — General requirements for the competence of testing and
calibration laboratories.
2. Subcontracting
2.1. In accordance with the provisions of Article 41(6) first subparagraph, a
manufacturer may nominate a subcontractor for performing tests on his
behalf.
By subcontractor it shall be understood:
a) either a subsidiary which is entrusted with testing activities by the manu

facturer inside its own organisation; or
b) a third party under contract with the manufacturer to perform test

activities.
2.2. Turning to the services of a subcontractor does not remove the obligation
for the manufacturer to comply with the provisions of Article 41 in
particular those concerning the skills of the technical services and
compliance with Standard EN ISO/IEC 17025:2005.
2.3. Section 1 of Annex XV shall apply to the subcontractor.
3. Test report
Test reports shall be drafted in accordance with the general requirements set
out in Appendix 3 of Annex V to Directive 2007/46/EC.
02007L0046 — EN — 18.01.2018 — 021.001 — 405
▼M9
ANNEX XVI
SPECIFIC CONDITIONS REQUIRED FROM VIRTUAL TESTING

METHODS AND REGULATORY ACTS FOR WHICH VIRTUAL
TESTING METHODS MAY BE USED BY A MANUFACTURER OR A
TECHNICAL SERVICE

This Annex lays down appropriate provisions concerning virtual testing in
accordance with Article 11(3).
It shall not apply to the second subparagraph of Article 11(2).
▼M26
1. List of regulatory acts
3 Fuel tanks/rear protective devices Directive 70/221/EEC
3B Rear underrun protective devices Regulation (EC) No 661/2009

(RUPDs) and their installation; rear
underrun protection (RUP)
6 Door latches and hinges Directive 70/387/EEC
6A Vehicle access and manoeuvrability Regulation (EC) No 661/2009

6B Door latches and door retention Regulation (EC) No 661/2009

components
8 Indirect vision devices Directive 2003/97/EC
8A Devices for indirect vision and their Regulation (EC) No 661/2009

installation
12 Interior fittings Directive 74/60/EEC
12A Interior fittings Regulation (EC) No 661/2009

16 Exterior projections Directive 74/483/EEC
16A External projections Regulation (EC) No 661/2009

20 Installation of lighting and light Directive 76/756/EEC

signalling devices
20A Installation of lighting and light- Regulation (EC) No 661/2009

signalling devices on vehicles
27 Towing hooks Directive 77/389/EEC
27A Towing device Regulation (EC) No 661/2009

32 Forward vision Directive 77/649/EEC

02007L0046 — EN — 18.01.2018 — 021.001 — 406
▼M26
32A Forward field of vision Regulation (EC) No 661/2009

35 Wash/wipe Directive 78/318/EEC
35A Windscreen wiper and washer systems Regulation (EC) No 661/2009

37 Wheel guards Directive 78/549/EEC
37A Wheel guards Regulation (EC) No 661/2009

42 Lateral protection Directive 89/297/EEC
42A Lateral protection of goods vehicles Regulation (EC) No 661/2009


49 External projections of cabs Directive 92/114/EEC
49A Commercial vehicles with regard to their Regulation (EC) No 661/2009

external projections forward of the cab's
rear panel
50 Couplings Directive 94/20/EC
50A Mechanical coupling components of Regulation (EC) No 661/2009

combinations of vehicles
50B Close-coupling device (CCD); fitting of Regulation (EC) No 661/2009

an approved type of CCD
52 Buses and coaches Directive 2001/85/EC
52A M2 and M3 vehicles Regulation (EC) No 661/2009

52B Strength of the superstructure of large Regulation (EC) No 661/2009

passenger vehicles
57 Front underrun protection Directive 2000/40/EC
57A Front underrun protective devices Regulation (EC) No 661/2009

(FUPDs) and their installation; front
underrun protection (FUP)
02007L0046 — EN — 18.01.2018 — 021.001 — 407
▼M9
Appendix 1
General conditions required from virtual testing methods
1. Virtual test pattern

The following scheme shall be used as basis structure for describing and
conducting virtual testing:
(a) purpose;
(b) structure model;
(c) boundary conditions;
(d) load assumptions;
(e) calculation;
(f) assessment;
(g) documentation.
2. Fundamentals of computer simulation and calculation

2.1. Mathematical model
The mathematical model shall be supplied by the manufacturer. It shall
reflect the complexity of the structure of the vehicle, system and
components to be tested in relation to the requirements of the regulatory
act and its boundary conditions.
The same provisions shall apply mutatis mutandis for testing components or
technical units independently from the vehicle.
2.2. Validation process of the mathematical model

The mathematical model shall be validated in comparison with the actual
test conditions.
To that effect a physical test shall be conducted for the purposes of

comparing the results obtained when using the mathematical model with
the results of a physical test. Comparability of the test results shall be
proven. A validation report shall be drafted by the manufacturer or by the
technical service and submitted to the approval authority.
Any change made to the mathematical model or to the software likely to

invalidate the validation report shall be brought to the attention of the
approval authority which may require that a new validation process is
conducted.
The flow chart of the validation process is shown in Appendix 3.
2.3. Documentation
The data and auxiliary tools used for the simulation and calculation shall be
made available by the manufacturer and be documented in a suitable way.
3. Tools and support

At the request of the technical service, the manufacturer shall supply or
provide access to the necessary tools including appropriate software.
02007L0046 — EN — 18.01.2018 — 021.001 — 408
▼M9
In addition he shall provide appropriate support to the technical service.
Providing access and support to a technical service does not remove any
obligation of the technical service regarding the skills of its personnel, the
payment of licence rights and respect of confidentiality.
02007L0046 — EN — 18.01.2018 — 021.001 — 409
▼M26
Appendix 2
Specific conditions concerning virtual testing methods
1. List of regulatory acts
Regulatory act reference Annex and paragraphs Specific conditions
3 Directive 70/221/EEC Annex II, points 5.2 and 5.4.5 Rear underrun dimensions and
resistance to forces
3B Regulation (EC) No 661/ Paragraphs 2.3, 7.3 and 25.6 Dimensions and resistance to forces
2009
UNECE Regulation
No 58
6 Directive 70/387/EEC Annex II, point 4.3 Equivalent methods for tensile
strength tests and resistance of
latches to acceleration
6A Regulation (EC) No 661/ Annex II, Part I and 2 Dimensions of steps, running boards
2009 and handholds
2012
6B Regulation (EC) No 661/ Annex 3 Tensile strength tests and resistance of

2009 latches to acceleration
Annex 4, point 2.1
UNECE Regulation
Annex 5
No 11
8 Directive 2003/97/EC Annex III Prescribed fields of vision of rear-view

mirrors.
All provisions in Sections 3, 4 and 5.
8A Regulation (EC) No 661/ Paragraph 15.2.4 Prescribed fields of vision of rear-view

2009 mirrors.
UNECE Regulation
No 46
12 Directive 74/60/EEC (a) Annex I, all provisions in point 5 (a) Measurement of all radii of
(Specifications) curvature and of all projections
except for those requirements
(b) Annex II
where a force has to be applied
in order to check compliance
with the provisions.
(b) Determination of the head-impact
zone.
12A Regulation (EC) No 661/ (a) Paragraph 5 to 5.7 (a) Measurement of all radii of
2009 curvature and of all projections
(b) Paragraph 2.3
except for those requirements
UNECE Regulation
where a force has to be applied
No 21
in order to check compliance
(b) Determination of the head-impact
zone.
16 Directive 74/483/EEC Annex I, all provisions in point 5 Measurement of all radii of curvature
(General specifications) and point 6 and of all projections except for those
(Particular specifications). requirements where a force has to be
applied in order to check compliance
02007L0046 — EN — 18.01.2018 — 021.001 — 410
▼M26
16A Regulation (EC) No 661/ Paragraph 5.2.4 Measurement of all radii of curvature
2009 and of all projections except for those
requirements where a force has to be
UNECE Regulation
No 26
20 Directive 76/756/EEC Paragraph 6 (Individual specifi The test drive provided for in
cations) of UNECE Regulation point 6.22.9.2.2 shall be performed
No 48. on a real vehicle.
Provisions of Annexes 4, 5 and 6 to
20A Regulation (EC) No 661/ Paragraph 6, Annexes 4, 5 and 6 The test drive provided for in
2009 point 6.22.9.2.2 shall be performed
on a real vehicle.
UNECE Regulation
No 48
27 Directive 77/389/EEC Annex II, point 2 Tractive and compressive static force
27A Regulation (EC) No 661/ Annex II, point 1.2 Tractive and compressive static force
2009
Regulation (EU)
No 1005/2010
32 Directive 77/649/EEC Annex I, point 5 (Specifications) Obstructions and field of vision
32A Regulation (EC) No 661/ Paragraph 5 Obstructions and field of vision

2009
UNECE Regulation
No 125
35 Directive 78/318/EEC Annex I, point 5.1.2 Determination of the swept area only.
35A Regulation (EC) No 661/ Annex III, points 1.1.2 and 1.1.3 Determination of the swept area only.
2009
Regulation (EU)
No 1008/2010
37 Directive 78/549/EEC Annex I, point 2 (Special

requirements)
37A Regulation (EC) No 661/ Annex II, point 2 Verification of the dimensional
2009 requirements
Regulation (EU)
No 1009/2010
42 Directive 89/297/EEC Annex, point 2.8 Resistance under a horizontal force

and deflection measurement.
42A Regulation (EC) No 661/ Paragraph 12.10 Resistance under a horizontal force
2009 and deflection measurement.
UNECE Regulation
No 73
02007L0046 — EN — 18.01.2018 — 021.001 — 411
▼M26
48A Regulation (EC) No 661/ (a) Annex I, Part B, points 7 and 8 (a) Check of compliance with the
2009 manoeuvrability requirements
(b) Annex I, Part C, points 6 and 7
including manoeuvrability of
Regulation (EU)
vehicles fitted with lift- or
No 1230/2012
loadable axles.
(b) Measurement of the maximum
rear swing-out.
49 Directive 92/114/EEC Annex I, point 4 (Specific Measurement of all radii of curvature

requirements) and of all projections except for those
49A Regulation (EC) No 661/ Paragraphs 5 and 6 Measurement of all radii of curvature
2009 and of all projections except for those
UNECE Regulation
No 61
50 Directive 94/20/EC (a) Annex V ‘Requirements for (a) All provisions of points 1 to 8
mechanical coupling Devices’ included.
(b) Annex VI, point 1.1 (b) Strength tests on mechanicals
couplings of simple design may
(c) Annex VI, point 4 (Testing of
be replaced by virtual tests.
mechanical coupling devices)
(c) Points 4.5.1 (Strength test), 4.5.2
(Resistance to buckling) and 4.5.3
(Resistance to bending moment)
only.
50A Regulation (EC) No 661/ (a) Annex 5 ‘Requirements for (a) All provisions of paragraphs 1 to
2009 mechanical coupling Devices’ 8 included.
UNECE Regulation (b) Annex 6, paragraph 1.1 (b) Strength tests on mechanicals
No 55 couplings of simple design may
(c) Annex 6, paragraph 3
be replaced by virtual tests.
(c) Paragraphs 3.6.1 (Strength test),
3.6.2 (Resistance to buckling)
and 3.6.3 (Resistance to bending
moment) only.
52 Directive 2001/85/EC (a) Annex I (a) Point 7.4.5 Stability test under the
conditions specified in the
(b) Annex IV Strength of super
Appendix to Annex I.
structure
(b) Appendix 4 — Verification of
strength of the superstructure by
calculation.
52A Regulation (EC) No 661/ Annex 3 Paragraph 7.4.5 (calculation method)

2009
UNECE Regulation
No 107
52B Regulation (EC) No 661/ Annex 9 Computer simulation of rollover test

2009 on complete vehicle as an equivalent
approval method
UNECE Regulation
No 66
02007L0046 — EN — 18.01.2018 — 021.001 — 412
▼M26
57 Directive 2000/40/EC Paragraph 3 of Annex 5 to UNECE Resistance under a horizontal force

Regulation 93. and deflection measurement.
57A Regulation (EC) No 661/ Annex 5, Paragraph 3. Resistance under a horizontal force
2009 and deflection measurement.
UNECE Regulation
No 93
02007L0046 — EN — 18.01.2018 — 021.001 — 413
▼M9
Appendix 3
Validation process
02007L0046 — EN — 18.01.2018 — 021.001 — 414
▼M24
ANNEX XVII
PROCEDURES TO BE FOLLOWED DURING MULTI-STAGE EC

TYPE-APPROVAL
1. OBLIGATIONS OF MANUFACTURERS
1.1. The satisfactory operation of the process of multi-stage EC type-approval
requires joint action by all the manufacturers concerned. To this end
approval authorities must ensure, before granting first and subsequent
stage approval, that suitable arrangements exist between the relevant
manufacturers for the supply and interchange of documents and
information such that the completed vehicle type meets the technical
requirements of all the relevant regulatory acts as prescribed in
Annex IV or Annex XI. Such information must include details of
relevant system, component and separate technical unit approvals and of
vehicle parts which form part of the incomplete vehicle but are not yet
approved. The manufacturer of the previous stage shall provide
information to the manufacturer of the subsequent stage regarding any
change that may affect system type-approvals or the whole vehicle
type-approval. Such information shall be provided as soon as the new
extension to the whole vehicle type has been issued and at the latest on
the starting date of production of the incomplete vehicle.
1.2. Each manufacturer in a multi-stage EC type-approval process is

responsible for the approval and conformity of production of all
systems, components or separate technical units manufactured by him or
added by him to the previously built stage. The manufacturer of the
subsequent stage is not responsible for subjects which have been
approved in an earlier stage except in those cases where he modifies
relevant parts to an extent that the previously granted approval becomes
invalid.
1.3. The multi-stage procedure may be used by a single manufacturer.

However, the multi-stage procedure shall not be used to circumvent the
requirements applicable to vehicles built in a single stage. In particular,
vehicles approved in this way are not considered to be multi-stage build in
the context of paragraph 3.4 of this Annex and Articles 22, 23 and 27 of
this Directive (Small series and End of Series limits).
2. OBLIGATIONS OF TYPE-APPROVAL AUTHORITIES

2.1. The type-approval authority shall:
(a) verify that all EC type-approval certificates issued pursuant to the

regulatory acts which are applicable for vehicle type-approval cover
the vehicle type at its state of completion and correspond to the
prescribed requirements;
(b) ensure that all the relevant data, taking account of the state of
completion of the vehicle, is included in the information folder;
(c) by reference to the documentation make sure that the vehicle specifi
cation(s) and data contained in Part I of the vehicle information folder
are included in the data in the information packages and in the EC
type-approval certificates, in respect of the relevant regulatory acts;
and in the case of a completed vehicle, where an item number in
Part I of the information folder is not included in the information
package of any of the regulatory acts, confirm that the relevant part
or characteristic conforms to the particulars in the information folder;
02007L0046 — EN — 18.01.2018 — 021.001 — 415
▼M24
(d) on a selected sample of vehicles from the type to be approved carry
out or arrange to be carried out inspections of vehicle parts and
systems to verify that the vehicle(s) is/are built in accordance with
the relevant data contained in the authenticated information package in
respect of all relevant regulatory acts;
(e) carry out or arrange to be carried out relevant installation checks in

respect of separate technical units where applicable.
2.2. The number of vehicles to be inspected for the purposes of paragraph

2.1(d) shall be sufficient to permit the proper control of the various
combinations to be EC type-approved according to the state of completion
of the vehicle and the following criteria:
— engine,
— gearbox,
— powered axles (number, position, interconnection),
— steered axles (number and position),
— body styles,
— number of doors,
— hand of drive,
— number of seats,
— level of equipment.
3. APPLICABLE REQUIREMENTS
3.1. EC type-approvals in accordance with this Annex are granted on the basis
of the current state of completion of the vehicle type and shall incorporate
all approvals granted at earlier stages.
3.2. For the whole vehicle type-approval, the legislation (in particular the
requirements of Annex II and the particular acts listed in Annex IV and
Annex XI to this Directive) shall apply in the same manner as if the
approval would be granted (or extended) to the manufacturer of the base
vehicle.
3.2.1 If a vehicle system/component type has not been modified, the system/
component approval granted in the previous stage remains valid as long as
the date for first registration in the particular regulatory act has not been
reached.
3.2.2. Where a vehicle system type has been modified at the subsequent stage to
the extent that it has to be retested for type-approval purposes, the
assessment shall be limited to only those parts of the system which
have been modified or affected by the changes.
3.2.3 Where a vehicle system or whole vehicle type has been modified by
another manufacturer at the subsequent stage to the extent that, except
the manufacturer name, it may still be considered as the same type, the
requirement applying to existing types may still be applied as long as the
date for first registration in the relevant regulatory act has not been
reached.
02007L0046 — EN — 18.01.2018 — 021.001 — 416
▼M24
3.2.4. Where the category of a vehicle is changed, the relevant requirements for
the new category shall be fulfilled. The type-approval certificates from the
previous category may be accepted provided that the requirements that the
vehicle complies with are the same or more stringent than those applying
to the new category.
3.3. Subject to the agreement of the approval authority, a whole vehicle

type-approval granted to the manufacturer of the subsequent stage needs
not to be extended or revised where an extension given at the previous
stage vehicle does not affect the subsequent stage or the technical data of
the vehicle. However, the type-approval number including the extension of
the previous stage(s) vehicle shall be copied in point 0.2.2 of the certificate
of conformity of the subsequent stage vehicle.
3.4. Where the cargo area of a complete or completed vehicle of category N or

O is modified by another manufacturer for the addition of removable
fittings to store and secure the cargo (for example, load space lining,
storage racks and roof racks), such items can be treated as part of the
pay-mass and an approval is not needed, if both of the following
conditions are met:
(a) the modifications do not affect the vehicle's type-approval in any way,
other than an increase of the actual mass of the vehicle;
(b) the added fittings can be removed without using special tools.
4. IDENTIFICATION OF THE VEHICLE

4.1. The identification number of the base vehicle (VIN) prescribed by
Regulation (EU) No 19/2011 (1) shall be retained during all the subsequent
stages of the type-approval process to ensure the ‘traceability’ of the
process.
4.2. At the second and subsequent stages, in addition to the statutory plate
prescribed by Regulation (EU) No 19/2011, each manufacturer shall
affix to the vehicle an additional plate the model of which is shown in
the appendix to this Annex. This plate shall be firmly attached, in a
conspicuous and readily accessible position on a part not subject to
replacement in use. It shall show clearly and indelibly the following
information in the order listed:
— name of the manufacturer,
— Sections 1, 3 and 4 of the EC type-approval number,
— the stage of approval,
— vehicle identification number of the base vehicle,
— technically permissible maximum laden mass of the vehicle where the

value has changed during the current stage of approval,
— technically permissible maximum laden mass of the combination

(where the value has changed during the current stage of approval
and where the vehicle is permitted to tow a trailer). ‘0’ shall be
used if the vehicle is not permitted to tow a trailer,
(1) Commission Regulation (EU) No 19/2011 of 11 January 2011 concerning type-approval

requirements for the manufacturer's statutory plate and for the vehicle identification
number of motor vehicles and their trailers and implementing Regulation (EC)
No 661/2009 of the European Parliament and of the Council concerning type-approval
requirements for the general safety of motor vehicles, their trailers and systems,
components and separate technical units intended therefor (OJ L 8, 12.1.2011, p. 1.)
02007L0046 — EN — 18.01.2018 — 021.001 — 417
▼M24
— technically permissible maximum mass on each axle, listed in order
from front to rear where the value has changed during the current stage
of approval,
— in the case of a semi-trailer or centre-axle trailer, the technically

permissible maximum mass at the coupling point where the value
has changed during the current stage of approval.
Unless otherwise provided for above, the plate shall comply with the
requirements of Annex I and Annex II to Regulation (EU) No 19/2011.
02007L0046 — EN — 18.01.2018 — 021.001 — 418
▼M24
Appendix
MODEL OF THE MANUFACTURER'S ADDITIONAL PLATE

The example below is given as a guide only.
MANUFACTURER'S NAME (stage 3)
e2*2007/46*2609
Stage 3
WD9VD58D98D234560
1 500 kg
2 500 kg
1 – 700 kg
2 – 810 kg
▼M22
__________
02007L0046 — EN — 18.01.2018 — 021.001 — 419
▼B
ANNEX XIX
TIMETABLE FOR THE ENFORCEMENT OF THIS DIRECTIVE IN RESPECT OF TYPE-APPROVAL
Enforcement dates
Categories concerned
New types of vehicles New types of vehicles Existing types of vehicles
Optional Obligatory Obligatory
M1 N.A. (*) 29 April 2009 N.A. (*)
Special-purpose vehicles of category 29 April 2009 29 April 2011 29 April 2012

M1
Incomplete and complete vehicles of 29 April 2009 29 October 2010 29 October 2011
category N1
Completed vehicles of category N1 29 April 2009 29 October 2011 29 April 2013
Incomplete and complete vehicles of 29 April 2009 29 October 2010 29 October 2012
categories N2, N3, O1, O2, O3, O4
Incomplete and complete vehicles of 29 April 2009 29 April 2009 (1) 29 October 2010
categories M2, M3,
Special-purpose vehicles of categories 29 April 2009 29 October 2012 29 October 2014

N 1, N 2, N 3, M 2 , M 3 , O 1 , O 2, O 3, O 4
Completed vehicles of categories N2, 29 April 2009 29 October 2012 29 October 2014
N3
Completed vehicles of categories M2, 29 April 2009 29 April 2010 (1) 29 October 2011
M3
Completed vehicles of categories O1, 29 April 2009 29 October 2011 29 October 2013
O 2, O 3 , O 4
(*) Not applicable.

(1) For the purposes of the application of Article 45(4), this date is postponed by 12 months.
02007L0046 — EN — 18.01.2018 — 021.001 — 420
▼B
ANNEX XX
TIME-LIMITS FOR THE TRANSPOSITION OF REPEALED

DIRECTIVES INTO NATIONAL LAW
PART A
Directive 70/156/EEC and its successive amending acts
Directives/regulations Comments
Directive 70/156/EEC (1)

Directive 95/54/EC (9) Article 3 only.
Directive 98/14/EC (13)
Directive 2001/116/EC (19)
Regulation (EC) No 807/2003 (20) Point (2) of Annex III only
Directive 2003/97/EC (21) Only Article 4
(1) OJ L 42, 23.2.1970, p. 1.
(2) OJ L 81, 28.3.1978, p. 1.
(3) OJ L 168, 26.6.1978, p. 39.
(4) OJ L 375, 31.12.1980, p. 34.
(5) OJ L 192, 11.7.1987, p. 51.
(6) OJ L 220, 8.8.1987, p. 44.
(7) OJ L 225, 10.8.1992, p. 1.
(8) OJ L 264, 23.10.1993, p. 49.
(9) OJ L 266, 8.11.1995, p. 1.
(10) OJ L 169, 8.7.1996, p. 1.
(11) OJ L 18, 21.1.1997, p. 7.
(12) OJ L 233, 25.8.1997, p. 1.
(13) OJ L 91, 25.3.1998, p. 1.
(14) OJ L 11, 16.1.1999, p. 25.
(15) OJ L 203, 10.8.2000, p. 9.
(16) OJ L 291, 8.11.2001, p. 24.
(17) OJ L 292, 9.11.2001, p. 21.
(18) OJ L 42, 13.2.2002, p. 42.
(19) OJ L 18, 21.1.2002, p. 1.
(20) OJ L 122, 16.5.2003, p. 36.
(21) OJ L 25, 29.1.2004, p. 1.
(22) OJ L 321, 6.12.2003, p. 15.
(23) OJ L 49, 19.2.2004, p. 36.
(24) OJ L 153, 30.4.2004, p. 107.
(25) OJ L 337, 13.11.2004, p. 13.
(26) OJ L 194, 26.7.2005, p. 12.
02007L0046 — EN — 18.01.2018 — 021.001 — 421
▼B
PART B
Time-limits for transposition into national laws
Directives Time-limits for transposition Date of application
Directive 70/156/EEC 10 August 1971
Directive 78/315/EEC 30 June 1979
Directive 78/547/EEC 15 December 1979
Directive 80/1267/EEC 30 June 1982
Directive 87/358/EEC 1 October 1988
Directive 92/53/EEC 31 December 1992 1 January 1993
Directive 95/54/EC 1 December 1995
Directive 96/27/EC 20 May 1997
Directive 96/79/EC 1 April 1997
Directive 97/27/EC 22 July 1999
Directive 98/14/EC 30 September 1998 1 October 1998
Directive 98/91/EC 16 January 2000
Directive 2000/40/EC 31 July 2002 1 August 2002
Directive 2001/92/EC 30 June 2002
Directive 2001/56/EC 9 May 2003
Directive 2001/85/EC 13 August 2003
Directive 2001/116/EC 30 June 2002 1 July 2002
Directive 2003/97/EC (1) 25 January 2005
Directive 2003/102/EC (2) 31 December 2003
Directive 2004/3/EC 18 February 2005
Directive 2004/78/EC 30 September 2004
Directive 2004/104/EC 31 December 2005 1 January 2006
Directive 2005/49/EC 30 June 2006 1 July 2006
(1) OJ L 25, 29.1.2004, p. 1.

(2) OJ L 321, 6.12.2003, p. 15.
02007L0046 — EN — 18.01.2018 — 021.001 — 422
▼B
ANNEX XXI
CORRELATION TABLE
(referred to in the second paragraph of Article 49)
Directive 70/156/EEC This Directive
— Article 1
Article 1, first subparagraph Article 2(1)
Article 1, second subparagraph Article 2(2)(a) and (b)
— Article 2(2)(c)
— Article 2(3) and (4)
Article 2 Article 3
— Article 4
— Article 5
— Article 6(1)
Article 3(1) Article 6(2)
— Article 6(4)
Article 3(4) Article 7(1) and (2)
Article 3(5) Articles 6(6) and 7(1)
Article 4(1), first subparagraph, Article 9(1)

point (a)

point (b)

point (c)

point (d)
— Article 10(3)
Article 4(1), second subparagraph Article 9(4)
Article 4(1), third subparagraph Article 9(5)
Article 4(3), first and third sentences Article 9(3)

02007L0046 — EN — 18.01.2018 — 021.001 — 423
▼B
Article 4(3), second sentence Article 8(4)
— Article 11
Article 5(3), first subparagraph Article 15(1)
Article 5(3), third subparagraph Articles 15(2), 16(1) and 16(2)
Article 5(3), fourth subparagraph Article 13(3)
Article 5(4), second subparagraph Articles 14(3) and 16(2)
Article 5(4), third subparagraph Article 14(2)
Article 5(4), fourth subparagraph, first Article 13(3)

sentence
Article 5(4), fourth subparagraph, Article 16(3)

second sentence
— Article 17(1) to (3)
— Article 18(2)
Article 6(2) —
— Article 19(3)
Article 6(4) Article 38(2), first subparagraph
— Article 38(2), second subparagraph

02007L0046 — EN — 18.01.2018 — 021.001 — 424
▼B
— Article 26(2)
Article 7(2) Article 28
Article 8(1) —
— Article 22
Article 8(2)(a), first sentence Article 26(3)
Article 8(2)(a), second sentence —
Article 8(2)(a), third to sixth sentences Article 23(1), (3), (5) and (6)
— Article 23(2)
— Article 23(4)
— Article 23(7)
Article 8(2)(b)(1), first and second Article 27(1)

subparagraphs
Article 8(2)(b)(1), third subparagraph Article 27(2)
Article 8(2)(b)(2), first and second Article 27(3)

subparagraphs
Article 8(2)(b)(2), third and fourth —

subparagraphs
Article 8(2)(c), first subparagraph Article 20(1) and (2)
Article 8(2)(c), second subparagraph Article 20(4), first subparagraph
Article 8(2)(c), third subparagraph —
Article 8(2)(c), fourth subparagraph Article 20(4), second subparagraph
— Article 20(4), third subparagraph
Article 8(2)(c), fifth and sixth Article 21(1), first subparagraph, and
subparagraphs Article 21(2)
— Article 21(1), second subparagraph
Article 8(3) Article 23(4), second subparagraph

02007L0046 — EN — 18.01.2018 — 021.001 — 425
▼B
— Article 24
— Article 25
Article 9(1) Article 36
— Article 34
— Article 35(2)
Article 10(2) Article 12(2), first subparagraph, first

sentence
— Article 12(2), first subparagraph,

second sentence
— Article 12(3)
— Article 31
— Article 32
Article 12, first sentence Article 33(1)
Article 12, second sentence Article 33(2)
— Article 37
— Article 38(1)
— Article 39(1)
— Article 40(2)
— Article 39(3) to (6), (8) and (9)
Article 14(1), first indent Article 43(1)
Article 14(1), second indent, first —

sentence
02007L0046 — EN — 18.01.2018 — 021.001 — 426
▼B
Article 14(1), second indent, second Article 41(4)

sentence
Article 14(1), second indent, point (i) Article 41(6)
Article 14(1), second indent, point (ii) —
Article 14(2), first subparagraph —
— Article 42
— Articles 44 to 51
Annex I Annex I
Annex II Annex II
Annex III Annex III
Annex IV Annex IV
— Annex IV, Appendix
Annex V Annex V
Annex VI Annex VI
— Annex VI, Appendix
Annex VII Annex VII
— Annex VII, Appendix
Annex VIII Annex VIII
Annex IX Annex IX
Annex X Annex X
Annex XI Annex XI
Annex XII Annex XII
— Annex XIII
Annex XIII Annex XIV
— Annex XV
— Annex XVI
Annex XIV Annex XVII
Annex XV Annex XVIII
— Annex XIX
— Annex XX
— Annex XXI

Celex:02007l0046 20180118:en:txt PDF

Uploaded by

Copyright:

Available Formats

Celex:02007l0046 20180118:en:txt PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Celex:02007l0046 20180118:en:txt PDF

Uploaded by

Copyright:

Available Formats

02007L0046 — EN — 18.01.2018 — 021.

►B DIRECTIVE 2007/46/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL

►M1 Commission Regulation (EC) No 1060/2008 of 7 October 2008 L 292 1 31.10.2008

►M4 Commission Regulation (EC) No 385/2009 of 7 May 2009 L 118 13 13.5.2009

►M7 Commission Directive 2010/19/EU of 9 March 2010 L 72 17 20.3.2010

►M8 amended by Commission Decision 2011/415/EU of 14 July 2011 L 185 76 15.7.2011

►M9 Commission Regulation (EU) No 371/2010 of 16 April 2010 L 110 1 1.5.2010

►M10 Commission Regulation (EU) No 183/2011 of 22 February 2011 L 53 4 26.2.2011

►M11 Commission Regulation (EU) No 582/2011 of 25 May 2011 L 167 1 25.6.2011

►M12 Commission Regulation (EU) No 678/2011 of 14 July 2011 L 185 30 15.7.2011

►M13 Commission Regulation (EU) No 65/2012 of 24 January 2012 L 28 24 31.1.2012

►M14 Commission Regulation (EU) No 1229/2012 of 10 December 2012 L 353 1 21.12.2012

►M15 Commission Regulation (EU) No 1230/2012 of 12 December 2012 L 353 31 21.12.2012

►M16 Commission Regulation (EU) No 143/2013 of 19 February 2013 L 47 51 20.2.2013

►M17 Commission Regulation (EU) No 171/2013 of 26 February 2013 L 55 9 27.2.2013

►M18 Commission Regulation (EU) No 195/2013 of 7 March 2013 L 65 1 8.3.2013

►M19 Council Directive 2013/15/EU of 13 May 2013 L 158 172 10.6.2013

►C1 Corrigendum, OJ L 308, 25.11.2015, p. 11 (661/2009)

This Directive establishes a harmonised framework containing the

Specific technical requirements concerning the construction and func­

1. This Directive applies to the type-approval of vehicles designed

It also applies to the individual approval of such vehicles.

2. This Directive does not apply to the type-approval or individual

(b) quadricycles as defined in Directive 2002/24/EC of the European

(c) tracked vehicles.

3. Type-approval or individual approval under this Directive is

(a) vehicles designed and constructed for use principally on

(c) mobile machinery,

4. An individual approval under this Directive is optional for the

(a) vehicles intended exclusively for racing on roads;

(b) prototypes of vehicles used on the road under the responsibility of a

1. ‘regulatory act’ means a separate directive or regulation or a

(1) OJ L 171, 9.7.2003, p. 1. Directive as last amended by Council Directive

3. ‘type-approval’ means the procedure whereby a Member State

4. ‘national type-approval’ means a type-approval procedure laid down

5. ‘EC type-approval’ means the procedure whereby a Member State

6. ‘individual approval’ means the procedure whereby a Member State

7. ‘multi-stage type-approval’ means the procedure whereby one or

8. ‘step-by-step type-approval’ means a vehicle approval procedure

9. ‘single-step type-approval’ means a procedure consisting in the

10. ‘mixed type-approval’ means a step-by-step type-approval

11. ‘motor vehicle’ means any power-driven vehicle which is moved by

12. ‘trailer’ means any non-self-propelled vehicle on wheels which is

— an electrical energy/power storage device (e.g. battery,

16. ‘mobile machinery’ means any self-propelled vehicle which is

17. ‘type of vehicle’ means vehicles of a particular category which do

20. ‘completed vehicle’ means a vehicle, resulting from the process of

22. ‘end-of-series vehicle’ means any vehicle that is part of a stock

23. ‘system’ means an assembly of devices combined to perform one or

24. ‘component’ means a device subject to the requirements of a regu­

25. ‘separate technical unit’ means a device subject to the requirements

27. ‘manufacturer’ means the person or body who is responsible to the

28. ‘manufacturer’s representative’ means any natural or legal person

29. ‘approval authority’ means the authority of a Member State with

30. ‘competent authority’ in Article 42 means either the approval

31. ‘technical service’ means an organisation or body designated by the

32. ‘virtual testing method’ means computer simulations including

34. ‘EC type-approval certificate’ means the certificate set out in

35. ‘individual approval certificate’ means the document whereby the

Specific technical requirements concerning the construction and func

24. ‘component’ means a device subject to the requirements of a regu