L011199 - PRONET-E Series Users Manual - V2.11

ProNet Series AC Servo User's Manual
（Version：V2.11）
Revision History
Date Rev. No. Section Revised Content Remark
2009-09 V1.00～V1.05 － First edition
2010-02 V1.06 All chapters Completely revised

1 Revision: Pn002
○
2 Revision: Pn840
○
Appendix A 3 Revision: Pn006.2
○
4 Addition: Pn411
○
2010-06 V1.07
5 Addition: Pn412
○
Addition: Low frequency vibration

4.6.5
suppression function
4.6.3 Revision: Position reference

2010-10 V1.08
Appendix A Revision: Pn006.3
1 Addition: ProNet-02A/04A
○
All chapters
2 Addition: Pn139 and Pn140
○
2010-11 V1.09
5.1.6 Addition: Un017
2011-04 V1.10 4.9.2 Revision: External Torque Limit
1 Addition: Wire-saving incremental encoder

○
2 Revision: Internal setting speed
○
All chapters 3 Addition: Description of OT signal
○
4 Addition: Description of /ALM signal
○
2011-07 V1.20 5 Addition: Description of /CLT signal
○
Addition: 4.6.8 Position Control (contact

4.6
reference)
Chapter 4 Addition: 4.12 Online Autotuning
2011-08 V1.21 Appendix A Revision: Pn006.3
Revision: Pn102、Pn107、Pn139、Pn14、
Appendix A
2011-09 V1.22 Pn413、Pn414、Pn511
Chapter 4 Addition: Description of /RD signal
All chapters Addition: ProNet-2BD
2011-12 V1.23 3.3.1 Revision: Encoder wiring
4.5.8 Revision: Encoder signal output phase form
4.6.9 Addition: Homing function
2012-02 V1.24 All chapters Addition: ProNet-10D/15D
Appendix B Addition: Alarm A67 and A69

1 Revision: ProNet-7.5kW~15kW
○
appearance
Chapter 1 and 3
2012-03 V1.25 2 Addition: Resolver description
○
Appendix
3 Addition: Reserved some parameters
○
4 Addition: Pn301 and Pn415
○
1 Revision: Pn307, Pn304, Pn681, Pn840

○
2 Addition: Alarm A19,A22, Pn523, Pn525,
○
Pn526
3 Deletion: A20
○
4 Deletion: Incremental wire-saving encoder
○
2012-05 V1.26 All chapters
5 Addition: 3.6
○
6 Addition: 3.7 Installation Conditions of EMC
○
Directives
7 Addition: 3.8 Using More than One Servo
○
Drive
1 Add ProNet-E Servo Drive

○
2 Add three phase 400V power supply
○
models：
ProNet-10D～75D/ ProNet-E-10D～50D
ProNet-1AD～2BD
3 Delete EML model
○
Revision:Connection Example for

2012-12 V2.01 4.6.1
Open-Collector Gate Output
ProNet-02A～04A/ ProNet-E-02A～04A
3.1.2
Add and revise note
ProNet-02A～04A/ ProNet-E-02A～04A
2013-1 V2.02 3.5.1
Add and revise note
Appendix A.3 Add note ○

2
Revision : ProNet-30A/ ProNet-50A/

2013-1 V2.03 7.1 ProNet-E-30A/ ProNet-E-50A Max. Output
Current
Revision :the value of external regenerative

2013-4 V2.04 3.1.2
resistors
Revision :the value of external regenerative

3.5.4
resistors
Add” Operating Conditions: electric power

7.1
system”
2.1 Addition:2.1.7Insatall to the Client
2013-9 V2.05 All chapters Format update
4.5.7 Add: /ZCLAMP
Addition:4.11.8 Torque Detection Output

4.11
（/TCR）
6.3.3 Revision : Communication data address

2014-01 V2.06
Revision：Pn121，Pn509，Pn510，Pn511
Appendix A
Add：Pn529，Pn530
Add 100VAC series servo drive:

All chapters
ProNet-02B~08B, ProNet-E-02B~08B
2014-02 V2.07 All chapters Add ProNet-70
2014-03 V2.08 Chapter 3 Add 3.9 Connecting DC Bus
2014-03 V2.09 Chapter 3 Revision: 3.9 Connecting DC Bus
Add: EML model

Revision:the main circuit of
ProNet-08B/ProNet-E-08B is single-phase
2014-06 V2.11 1.1.1 Update Servomotor Model Designation

Copyright © 2011 ESTUN AUTOMATION TECHNOLOGY CO., LTD
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form, or
by any means, mechanical, electronic, photocopying, recording, or otherwise, without the prior written permission of ESTUN.
No patent liability is assumed with respect to the use of the information contained herein.
About this manual
 This manual describes the following information required for designing and maintaining ProNet series servo drives.
•Specification of the servo drives and servomotors.
•Procedures for installing the servo drives and servomotors.
•Procedures for wiring the servo drives and servomotors.
•Procedures for operating of the servo drives.
•Procedures for using the panel operator.
•Communication protocols.
•Ratings and characteristics.
 Intended Audience:
•Those designing ProNet series servo drive systems.
•Those installing or wiring ProNet series servo drives.
•Those performing trial operation or adjustments of ProNet series servo drives.
•Those maintaining or inspecting ProNet series servo drives.
-1-
Safety Precautions
■ Do not connect the servomotor directly to the local electrical network.
Failure to observe this may result in damage to servomotor.
■ Do not plug or unplug connectors from servo drive when power is on.
Failure to observe this may result in damage to servo drive and servomotor.
■Please note that even after power is removed, residual voltage still remains in the capacitor inside the servo drive. If
inspection is to be performed after power is removed, please wait 5 minutes to avoid risk of electrical shock.
■ Keep servo drives and other devices separated by at least 10mm.
The servo drive generates heat. Install the servo drive so that it can radiate heat freely. When installing servo drives
with other devices in a control panel, provide at least 10mm space between them and 50mm space above and below
them. Please install servo drives in an environment free from condensation, vibration and shock.
■ Perform noise reduction and grounding properly.
Please comply with the following instructions to avoid noise generated by signal lines.
1. Separate high-voltage cables from low-voltage cables.
2. Use cables as short as possible.
3. Single point grounding is required for the servomotor and servo drive (grounding resistance 100Ω or below).
4. Never use a line filter for the power supply in the circuit.
■ Conduct a voltage resistance test for the servo drive under the following conditions:
1. Input voltage: AC 1500Vrms, 1 minute
2. Braking current: 100mA
3. Frequency:50/60Hz
4. Voltage applied point: Between L1, L2,L3 terminals and frame ground.
■ Use a fast-response type ground-fault interrupter.
For a ground-fault interrupter, always use a fast-response type or one designed for PWM inverters. Do not use a
time-delay type.
■ Do not make any extreme adjustments or setting changes of parameters.
Failure to observe this caution may result in injury or damage to the product due to unstable operation.
■ The servomotor cannot be operated by turning the power on and off.
Frequently turning the power ON and OFF causes the internal circuit elements to deteriorate, resulting in unexpected
problems. Always start or stop the servomotor by using reference pulses.
-2-
—Contents—
About this manual ........................................................................................................................................................... - 1 -
Safety Precautions .......................................................................................................................................................... - 2 -
Chapter 1 ........................................................................................................................................................................ - 7 -
Checking Products and Parts Names..............................................................................................................................- 7 -

1.1 Checking Products on Delivery ......................................................................................................................... - 7 -
1.1.1 Servomotor ............................................................................................................................................ - 7 -
1.1.2 Servo drive .......................................................................................................................................... - 10 -
1.2 Part Names ..................................................................................................................................................... - 17 -
1.2.1 Servomotor .......................................................................................................................................... - 17 -
1.2.2 Servo drive .......................................................................................................................................... - 17 -
Chapter 2 ...................................................................................................................................................................... - 23 -
Installation ..................................................................................................................................................................... - 23 -
2.1 Servomotor ..................................................................................................................................................... - 23 -
2.1.1 Storage ................................................................................................................................................ - 23 -
2.1.2 Installation Sites .................................................................................................................................. - 23 -
2.1.3 Installation Alignment ........................................................................................................................... - 24 -
2.1.4 Installation Orientation ......................................................................................................................... - 24 -
2.1.5 Handling Oil and Water ........................................................................................................................ - 24 -
2.1.6 Cable Tension ...................................................................................................................................... - 25 -
2.1.7 Install to the Client ............................................................................................................................... - 25 -
2.2 Servo Drive ..................................................................................................................................................... - 25 -
2.2.1 Storage ................................................................................................................................................ - 25 -
2.2.2 Installation Sites .................................................................................................................................. - 25 -
2.2.3 Installation Orientation ......................................................................................................................... - 26 -
2.2.4 Installation Method .............................................................................................................................. - 26 -
Chapter 3 ...................................................................................................................................................................... - 28 -
Wiring ............................................................................................................................................................................ - 28 -
3.1 Main Circuit Wiring .......................................................................................................................................... - 28 -
3.1.1 Names and Functions of Main Circuit Terminals .................................................................................. - 28 -
3.1.2 Typical Main Circuit Wiring Examples .................................................................................................. - 29 -
3.2 I/O Signals ...................................................................................................................................................... - 33 -
3.2.1 Examples of I/O Signal Connections ................................................................................................... - 33 -
3.2.2 I/O Signal Names and Functions ......................................................................................................... - 34 -
3.2.3 I/O Signal Connector (CN1) Terminal Layout ...................................................................................... - 36 -
3.2.4 Interface Circuit ................................................................................................................................... - 37 -
3.3 Wiring Encoders.............................................................................................................................................. - 38 -
3.3.1 Connecting an Encoder(CN2).............................................................................................................. - 38 -
3.3.2 Encoder Connector(CN2) Terminal Layout ......................................................................................... - 40 -
3.4 Communication Connection ............................................................................................................................ - 40 -
3.4.1 Communication Connector(CN3) Terminal Layout .............................................................................. - 40 -
3.4.2 Communication Connector(CN4) Terminal Layout .............................................................................. - 41 -
3.5 Standard Wiring Examples .............................................................................................................................. - 42 -
3.5.1 Single-phase 200V ProNet-02A～04A/ProNet-E-02A～04A ............................................................... - 42 -
-3-
3.5.2 Three-phase 200V ProNet-08A～50A/ProNet-E-08A～50A ................................................................ - 43 -

3.5.3 Three-phase 400V ProNet-10D～75D/ProNet-E-10D～50D ............................................................... - 44 -
3.5.4 Three-phase 400V ProNet-1AD～2BD ................................................................................................ - 45 -
3.5.5 Single-phase 100V ProNet-02B/ProNet-E-02B ................................................................................... - 46 -
3.5.6 Single-phase 100V ProNet-04B /ProNet-E-04B .................................................................................. - 47 -
3.5.7 Single-phase 100V ProNet-08B/ ProNet-E-08B .................................................................................. - 48 -
3.5.8 Position Control Mode ......................................................................................................................... - 49 -
3.5.9 Speed Control Mode ............................................................................................................................ - 50 -
3.5.10 Torque Control Mode ......................................................................................................................... - 51 -
3.6 Wiring for Noise Control .................................................................................................................................. - 52 -
3.6.1 Noise Control ....................................................................................................................................... - 52 -
3.6.2 Precautions on Connecting Noise Filter .............................................................................................. - 53 -
3.7 Installation Conditions of EMC Directives ....................................................................................................... - 55 -
3.8 Using More than One Servo Drive .................................................................................................................. - 57 -
3.9 Connecting DC Bus ........................................................................................................................................ - 59 -
Chapter 4 ...................................................................................................................................................................... - 60 -
Operation ...................................................................................................................................................................... - 60 -
4.1 Trial Operation ................................................................................................................................................ - 60 -
4.1.1 Trial Operation for Servomotor Without Load ...................................................................................... - 63 -
4.1.2 Trial Operation for Servomotor without Load from Host Reference ..................................................... - 65 -
4.1.3 Trial Operation with the Servomotor Connected to the Machine.......................................................... - 69 -
4.1.4 Trial Operation for Servomotor with Brakes ......................................................................................... - 70 -
4.1.5 Position Control by Host Controller ...................................................................................................... - 70 -
4.2 Control Mode Selection................................................................................................................................... - 70 -
4.3 Setting Common Basic Functions ................................................................................................................... - 72 -
4.3.1 Setting the Servo ON Signal ................................................................................................................ - 72 -
4.3.2 Switching the Servomotor Rotation Direction ...................................................................................... - 73 -
4.3.3 Setting the Overtravel Limit Function ................................................................................................... - 74 -
4.3.4 Setting for Holding Brakes ................................................................................................................... - 77 -
4.3.5 Instantaneous Power Loss Settings..................................................................................................... - 80 -
4.4 Absolute Encoders .......................................................................................................................................... - 81 -
4.4.1 Selecting an Absolute Encoder ............................................................................................................ - 81 -
4.4.2 Handling Battery .................................................................................................................................. - 82 -
4.4.3 Replacing Battery ................................................................................................................................ - 83 -
4.4.4 Absolute Encoder Setup(Fn010、Fn011) ............................................................................................ - 83 -
4.5 Operating Using Speed Control with Analog Reference.................................................................................. - 84 -
4.5.1 Setting Parameters .............................................................................................................................. - 84 -
4.5.2 Setting Input Signals ............................................................................................................................ - 85 -
4.5.3 Adjusting Reference Offset .................................................................................................................. - 86 -
4.5.4 Soft Start .............................................................................................................................................. - 89 -
4.5.5 Speed Reference Filter Time Constant ................................................................................................ - 89 -
4.5.6 S-curve Risetime ................................................................................................................................. - 90 -
4.5.7 Using the Zero Clamp Function ........................................................................................................... - 90 -
4.5.8 Encoder Signal Output ........................................................................................................................ - 92 -
4.5.9 Speed coincidence output ................................................................................................................... - 93 -
4.6 Operating Using Position Control .................................................................................................................... - 94 -
-4-
4.6.1 Basic Setting in Position Control.......................................................................................................... - 94 -

4.6.2 Setting the Clear Signal ....................................................................................................................... - 98 -
4.6.3 Setting the Electronic Gear .................................................................................................................. - 98 -
4.6.4 Smoothing ......................................................................................................................................... - 101 -
4.6.5 Low Frequency Vibration Suppression .............................................................................................. - 102 -
4.6.6 Positioning Completion Output Signal ............................................................................................... - 104 -
4.6.7 Reference Pulse Inhibit Function (INHIBIT) ....................................................................................... - 105 -
4.6.8 Position Control (contact reference) ................................................................................................. - 106 -
4.6.9 Position Homing Control (Homing Function)...................................................................................... - 109 -
4.7 Operating Using Torque Control.................................................................................................................... - 112 -
4.7.1 Setting Parameters ............................................................................................................................ - 112 -
4.7.2 Torque Reference Input ..................................................................................................................... - 113 -
4.7.3 Adjusting the Reference Offset .......................................................................................................... - 114 -
4.7.4 Limiting Servomotor Speed During Torque Control ............................................................................ - 115 -
4.8 Operating Using Speed Control with an Internally Set Speed ....................................................................... - 116 -
4.8.1 Setting Parameters ............................................................................................................................ - 117 -
4.8.2 Input Signal Settings .......................................................................................................................... - 118 -
4.8.3 Operating Using an Internally Set Speed ........................................................................................... - 118 -
4.9 Limiting Torque.............................................................................................................................................. - 119 -
4.9.1 Internal Torque Limit .......................................................................................................................... - 119 -
4.9.2 External Torque Limit ......................................................................................................................... - 120 -
4.9.3 Torque Limiting Using an Analog Voltage Reference ........................................................................ - 121 -
4.10 Control Mode Selection ............................................................................................................................... - 122 -
4.10.1 Setting Parameters .......................................................................................................................... - 122 -
4.10.2 Switching the Control Mode ............................................................................................................. - 122 -
4.11 Other Output Signals ................................................................................................................................... - 123 -
4.11.1 Servo alarm output........................................................................................................................... - 123 -
4.11.2 Rotation Detection Output Signal (/TGON) ...................................................................................... - 124 -
4.11.3 Servo Ready (/S-RDY) Output ......................................................................................................... - 124 -
4.11.4 Encoder C Pluse Output (/PGC) ...................................................................................................... - 124 -
4.11.5 Over travel signal output (OT) .......................................................................................................... - 125 -
4.11.6 Servo Enabled Motor Excitation Output(/RD) .................................................................................. - 125 -
4.11.7 Torque Limit Detection Output (/CLT) ............................................................................................... - 125 -
4.11.8 Torque Detection Output (/TCR) ...................................................................................................... - 127 -
4.12 Online Autotuning........................................................................................................................................ - 127 -
4.12.1 Online Autotuning ............................................................................................................................ - 127 -
4.12.2 Online Autotuning Procedure ........................................................................................................... - 128 -
4.12.3 Setting Online Autotuning ................................................................................................................ - 129 -
4.12.4 Machine Rigidity Setting for Online Autotuning ................................................................................ - 129 -
Chapter 5 .................................................................................................................................................................... - 130 -
Panel Operator ............................................................................................................................................................ - 130 -

5.1 Basic Operation ............................................................................................................................................ - 130 -
5.1.1 Functions on Panel Operator ............................................................................................................. - 130 -
5.1.2 Resetting Servo Alarms ..................................................................................................................... - 130 -
5.1.3 Basic Mode Selection ........................................................................................................................ - 131 -
5.1.4 Status Display Mode .......................................................................................................................... - 131 -
-5-
5.1.5 Operation in Parameter Setting Mode ............................................................................................... - 133 -

5.1.6 Operation in Monitor Mode ................................................................................................................ - 134 -
5.2 Operation in Utility Function Mode ................................................................................................................ - 137 -
5.2.1 Alarm Traceback Data Display ........................................................................................................... - 137 -
5.2.2 Parameter Settings Initialization ........................................................................................................ - 138 -
5.2.3 Operation in JOG Mode ..................................................................................................................... - 139 -
5.2.4 Automatic Adjustment of the Speed Reference Offset ....................................................................... - 140 -
5.2.5 Manual Adjustment of the Speed Reference Offset ........................................................................... - 141 -
5.2.6 Offset-adjustment of Servomotor Current Detection Signal ............................................................... - 142 -
5.2.7 Software Version Display ................................................................................................................... - 144 -
5.2.8 Position Teaching Function ................................................................................................................ - 144 -
5.2.9 Static Inertia Detection ....................................................................................................................... - 144 -
5.2.10 Absolute Encoder Multiturn Data and Alarm Reset .......................................................................... - 145 -
5.2.11 Absolute Encoder Related Alarms Reset ......................................................................................... - 145 -
Chapter 6 .................................................................................................................................................................... - 146 -
MODBUS Communication........................................................................................................................................... - 146 -

6.1 RS-485 Communication Wiring ..................................................................................................................... - 146 -
6.2 MODBUS Communication Related Parameters ........................................................................................... - 147 -
6.3 MODBUS Communication Protocol .............................................................................................................. - 148 -
6.3.1 Code Meaning ................................................................................................................................... - 148 -
6.3.2 Communication Error Disposal .......................................................................................................... - 154 -
6.3.3 Data Communication Address of Servo State .................................................................................... - 155 -
Chapter 7 .................................................................................................................................................................... - 158 -
Specifications and Characters ..................................................................................................................................... - 158 -

7.1 Servo drive Specifications and Models ......................................................................................................... - 158 -
7.2 Servo drive Dimensional Drawings ............................................................................................................... - 161 -
Appendix A .................................................................................................................................................................. - 164 -
Parameter ................................................................................................................................................................... - 164 -

A.1 Parameter List .............................................................................................................................................. - 164 -
A.2 Description of Parameter Type ..................................................................................................................... - 171 -
A.3 Parameters in detail...................................................................................................................................... - 172 -
Appendix B .................................................................................................................................................................. - 190 -
Alarm Display .............................................................................................................................................................. - 190 -
-6-
Chapter 1
Checking Products and Parts Names
1.1 Checking Products on Delivery

Check Items Comments
Are the delivered products the ones that Check the model numbers marked on the nameplate on the
were ordered? servomotor and servo drive.
Check the overall appearance, and check for damage or scratches
Is there any damage?
that may have occurred during shipping.
If the servomotor shaft can be easily rotated by hand, then the motor
Does the servomotor shaft rotate smoothly? is working normally. However, if a brake is installed on the
servomotor, then it cannot be turned by hand.
If any of the above items are faulty or incorrect, contact your ESTUN representative or the dealer from whom you
purchased the products.
1.1.1 Servomotor
 Servomotor Model Designation
EMJ– 08 A P B 1 1 -WR
ESTUN Servomotor
【1+2】【3】【4】【5】【6】【7】【8+9】
EMJ Model
【1+2】
【4】Encoder 【7】Option
Rated Output
Code Spec. Code Spec. Code Spec.
A5 0.05 kW D Incremental encoder ：131072P/R 1 None
01 0.1 kW Incremental Wire-saving Type： 2 With oil seal
P
02 0.2kW 2500P/R 3 With brake (DC24V)
04 0.4kW S Absolute encoder：131072P/R 4 With oil seal and brake(DC24V)
08 0.75kW 【5】Designing Sequence 【8+9】Connector
10 1.0kW Code Spec. Code Spec.
A Designing sequence A Standard connector
B Designing sequence B Water proof connector (Incremental
WR
【3】Voltage 【6】Shaft End Wire-saving Type )
Code Spec. Code Spec.

A 200VAC 1 Straigt without key （Standard）
B 100VAC 2 Straigt with key and tap
Note：EMJ-A5/01APA□□、EMJ-□□AD□□□ and EMJ-□□AS□□□ support water proof connector default
-7-
EMG– 10 A D A 1 1
ESTUN Servomotor
【1+2】【3】【4】【5】【6】【7】
EMG Model
【1+2】
Rated Output
10 1.0kW D Incremental encoder ：131072P/R 1 None
15 1.5kW 2 With oil seal

P Incremental Wire-saving Type：2500P/R
20 2.0kW 3 With brake (DC24V)
50 5.0kW
【3】Voltage 【5】Designing Sequence 【6】Shaft End
A 200VAC A Designing sequence A 1 Straigt without key （Standard）
D 400VAC 2 Straigt with key and tap
Note：1. The EMG-30A□A□□, EMG-50A□A□□ servomotors are not mounted with an incremental encoder.
2. There is no brake mounted on the EMG-□□□DA□□ servomotor.
EML– 10 A D A 1 1
ESTUN Servomotor
【1+2】【3】【4】【5】【6】【7】
EML Model
【1+2】
Rated Output
10 1.0kW D Incremental encoder ：131072P/R 1 None
20 2.0kW P Incremental Wire-saving Type:2500P/R 2 With oil seal
30 3.0kW R Resolver 3 With brake (DC24V)

A 200VAC A Designing sequence A 1 Straigt without key （Standard）
D 400VAC B Designing sequence B 2 Straigt with key and tap
Note：1. EML-20□□A□□、EML-30□□A□□、EML-40□□A□□are not mounted with an incremental encoder.

2. There is no brake mounted on the EML-10□D□□□ servomotor.
-8-
EMB– 1E D S A 1 1
ESTUN Servomotor
【1+2】【3】【4】【5】【6】【7】
EMB Model
【1+2】
Rated Output
75 7.5kW S Absolute encoder：131072P/R 1 None
1A 11.0kW R Resolver 2 With oil seal
1E 15.0kW 3 With brake (DC24V)
2B 22.0kW 4 With oil seal and brake(DC24V)

D 400VAC A Designing sequence A 1 Straigt without key （Standard）
2 Straigt with key and tap
 Appearance and Nameplate
-9-
1.1.2 Servo drive
 ProNet Servo drive Model Designation
PRONET – 10 A E A -P
ProNet Model
Extended module type
Rated Output
-D DP100
02 0.2kW
-E EC100
04 0.4 kW
-P PL100
08 0.75 kW
10 1.0 kW
15 1.5 kW
20 2.0 kW
30 3.0 kW
50 5.0 Kw
70 7.0kW
75 7.5 kW Encoder Interface
1A 11 kW A 17-bit serial encoder
1E 15 Kw Absolute Encoder
2B 22kW B Resolver○ 1
Voltage
A 200VAC
B：100VAC
D 400VAC
Control Mode
M Speed control, torque control, position control
E Speed control, torque control, position control (support extended module)
Note:
○
1 Resolver, with the feature of high reliability and long service life, is suitable for harsh environments and a wide range
of temperatures and humidity levels. The factory setting for the resolver precision used in the ESTUN servo drive is
4096.
2 ProNet-□□□E□ Supports AE100 model. ProNet-□□□M□ does not support extended module.
○
 ProNet-E Servo drive Model Designation
PRONET–E – 10 A
Voltage
ProNet-E Model
A：200VAC
B：100VAC
D：400VAC
Rated Output
02 0.2kW
04 0.4 kW
08 0.75 kW
10 1.0 kW
15 1.5 kW
20 2.0 kW
30 3.0 kW
50 5.0 kW
- 10 -
Note:
○
1 ProNet-E is only available with the wire-saving incremental encoder (2500 P/R)
2 ProNet-E does not support extended module.

○
 ProNet Servo Drive Appearance
ProNet-02A/04A ProNet-08A/10A
CHARGE POWER
CN3
L1
L2
CN4
L3
＋1
＋2
L1C
CN1
L2C
B1
B2
B3
V
CN2
ProNet-15A/20A ProNet-10D/15D/20D
CHARGE POWER CHARGE POWER

CN3
CN3
L1 L1
L2 L2
CN4
CN4
L3 L3
＋1 ＋1
＋2 ＋2
－－
L1C
CN1
24V
CN1
L2C GND
B1 B1
B2 B2
B3 B3
U U
V V
CN2
CN2
W W
- 11 -
ProNet-30A/50A ProNet-30D/50D/70D/75D
CHARGE
CHARGE POWER
POWER
CN3
CN3
L1
CN4
L1
L2
CN4
L2
L3
L3
＋1
＋1
＋2
CN1
＋2
CN1
－
24V
L1C GND
L2C B1
CN2
B1
CN2
B2
B2 B3
B3 U
U V
V W
ProNet-1AD/1ED/2BD ProNet-02B
- 12 -
ProNet-04B ProNet-08B
 ProNet-E Servo Drive Appearance
ProNet-E-02A/04A ProNet-E-08A/10A
CHARGE POWER
CN3
L1
L2
CN4
CN3
L3
CHARGE
＋1
L1
CN4
L2 ＋2
FG
－
＋1
＋2 L1C
CN1
－ L2C
B1
CN1
L1C
B2
L2C B3
B1
B2
U
B3
V
W
CN2
V
W
CN2
- 13 -
ProNet-E-15A/20A ProNet-E-10D/15D/20D
CHARGE POWER
CN3
CHARGE POWER
L1
CN3
L2
CN4
L1 L3
L2 ＋1
CN4
L3
＋2
＋1
－
＋2
24V
CN1
－
GND
L1C B1
CN1
L2C B2
B1 B3
B2
U
B3
V
U
CN2
W
V
CN2
ProNet-E-30A/50A ProNet-E-30D/50D
CHARGE CHARGE
POWER POWER
CN3
CN3
L1 L1
CN4
CN4
L2 L2
L3 L3
＋1 ＋1
＋2
CN1
＋2
CN1
－
－
L1C
24V
L2C
GND
B1
CN2
B1
CN2
B2
B2
B3
B3
U
U
V
V
W
W
- 14 -
ProNet-E-02B ProNet-E-04B
ProNet-E-08B
- 15 -
 ProNet Servo Drive Nameplate
Servodrive model
Applicable power Applicable servomotor
supply capacity
Serial number
 ProNet-E Servo Drive Nameplate
- 16 -
1.2 Part Names
1.2.1 Servomotor
Servomotor without gear and brake.
Encoder
Mounting hole
Shell
Output shaft
Flange
1.2.2 Servo drive
 ProNet-02A/04A/ProNet-E-02A/04A
Charge indicator
Lights when the main circuit power supply is
ON and stays lit as long as the main circuit
power supply capacitor remains charged.
Connector for communication
Main circuit power supply terminals
Used to communicate with other devices.
Used for main circuit power supply input.
Connecting terminal of DC reactor
I/O signal connector

Control power supply terminals Used for reference input signals
Used for control power supply input. and sequence I/O signals.
Regenerative resistor connecting terminals
Used to connect external regenerative resistors.
Servomotor terminals
Connects to the servomotor power line. Encoder connector
Connects to the encoder in the
Ground terminal servomotor.
Be sure to connect to protect electric shock.
- 17 -
 ProNet-08A/10A /ProNet-E-08A/10A
CN3
CN4
CN1
CN2
 ProNet-15A/20A/ ProNet-E-15A/20A
CHARGE POWER
CN3
L1
L2
CN4
L3
＋1
＋2
L1C
CN1
L2C
B1
B2
B3
V
CN2
- 18 -
 ProNet-10D/15D/20D/ProNet-E-10D/15D/20D
Charge indicator
ON and stays lit as long as the main circuit CHARGE POWER Power on indicator
power supply capacitor remains charged. Lights when the control power supply is on.
CN3
L1
Main circuit power supply terminals L2 Connector for communication
Used for main circuit power supply input. Used to communicate with other devices.
CN4
L3
＋1
Connecting terminal of DC reactor ＋2
Control power supply terminals I/O signal connector

Used for control power supply input. Used for reference input
CN1
24V
GND

B1
signals and sequence I/O
B2
Used to connect external regenerative resistors. B3 signals.
U

CN2
W
Ground terminal Connects to the encoder

Be sure to connect to protect electric shock. in the servomotor.
 ProNet-30A/50A/ ProNet-E-30A/50A
Charge indicator
Lights when the main circuit
power supply is ON and
stays lit as long as the main
circuit power supply
CHARGE
POWER Power on indicator
Lights when the control power supply is
CN3
capacitor remains charged.

on.
L1
Main circuit power
CN4
supply terminals L2 Connector for communication

Used for main circuit L3 Used to communicate with other devices.
power supply input. ＋1
Connecting terminal ＋2 I/O signal connector

CN1
of DC reactor Used for reference input

－
signals and sequence I/O
Control power supply L1C signals.
terminals
L2C
Used for control power
Encoder connector
supply input. B1
CN2
Connects to the encoder

Regenerative resistor B2
in the servomotor.
connecting terminals B3
Used to connect external
U
regenerative resistors.
V
W
Connects to the servomotor
power line.
Ground terminal
Be sure to connect to protect
electric shock.
- 19 -
 ProNet-30D/50D/70D/75D/ ProNet-E-30D/50D
Charge indicator
Power on indicator
CHARGE
Lights when the control power supply is
capacitor remains charged. POWER
on.
CN3
Main circuit power Connector for communication
L1
supply terminals
CN4
L2 Used to communicate with other devices.
Used for main circuit
L3
power supply input.
＋1
Connecting terminal
＋2
of DC reactor
CN1
Used for reference input
－
Control power supply signals and sequence I/O
terminals 24V signals.
Used for control power GND
supply input. B1
Encoder connector
CN2
Regenerative resistor Connects to the encoder
B2
connecting terminals in the servomotor.
B3
regenerative resistors. U
Servomotor terminals V
Connects to the servomotor W

power line.
Ground terminal
electric shock.
 ProNet-1AD/1ED/2BD
- 20 -
 ProNet-02B/ProNet-E-02B
Charge indicator
ON and stays lit as long as the main circuit
power supply capacitor remains charged.
Connector for communication
Main circuit power supply terminals
Used to communicate with other devices.
Used for main circuit power supply input.
Connecting terminal of DC reactor

Control power supply terminals Used for reference input signals
Used for control power supply input. and sequence I/O signals.
Used to connect external regenerative resistors.
Connects to the encoder in the
Ground terminal servomotor.
Be sure to connect to protect electric shock.
 ProNet-04B/ProNet-E-04B
Charge indicator
stays lit as long as the main Power on indicator
circuit power supply Lights when the control power supply is
capacitor remains charged. on.
Main circuit power
supply terminals
Used for main circuit Connector for communication
power supply input. Used to communicate with other devices.
Connecting terminal
of DC reactor
Control power supply
terminals
supply input.
Regenerative resistor I/O signal connector
connecting terminals Used for reference input
Used to connect external signals and sequence I/O
regenerative resistors. signals.
Connects to the servomotor
Encoder connector
power line.
Connects to the encoder
Ground terminal
in the servomotor.
electric shock.
- 21 -
 ProNet-08B /ProNet-E-08B
Charge indicator
capacitor remains charged. Power on indicator
Main circuit power Lights when the control power supply is
supply terminals on.
Used for main circuit Connector for communication
power supply input. Used to communicate with other devices.
Connecting terminal
of DC reactor
Control power supply
terminals
Used for reference input
supply input.
Regenerative resistor signals and sequence I/O
connecting terminals signals.
regenerative resistors.
Connects to the servomotor Encoder connector
power line. Connects to the encoder
Ground terminal in the servomotor.
electric shock.
- 22 -
Chapter 2
Installation
2.1 Servomotor
Servomotor can be installed either horizontally or vertically. However, if the servomotor is installed incorrectly, the
service life of the servomotor will be shortened or unexpected problems may occur.
Please observe the installation instructions described below to install the servomotor correctly.
Before installation:
Anticorrosive paint is coated on the edge of the servomotor shaft. Clean off the anticorrosive paint thoroughly using
a cloth moistened with thinner.
Avoid getting thinner on other parts of the servomotor when cleaning the shaft.
2.1.1 Storage
When the servomotor is not being used, store it in an area with a temperature between -25℃ and 60℃ with the power
cable disconnected.
2.1.2 Installation Sites
The servomotor is designed for indoor use. Install the servomotor in an environment which meets the following
conditions.
 Free from corrosive and explosive gases.
 Well-ventilated and free from dust and moisture.
 Ambient temperature from 0 to 40℃.
 Relative humidity from 26% to 80%( non-condensing).
 Facilitates inspection and cleaning.
- 23 -
2.1.3 Installation Alignment
Align the shaft of the servomotor with that of the machinery shaft to be controlled. Then connect the two shafts with an
elastic coupling.
Install the servomotor so that alignment accurancy falls within the range shown below.
Measure this distance at four different positions in the circumference. The difference between the maximum and
minimum measurements must be 0.03mm or less.(Turn together with couplings.)
Note:
·If the alignment accurancy is incorrect , vibration will occur, resulting in damage to the bearings.
·Mechanical shock to the shaft end is forbidden, otherwise it may result in damage to the encoder of the servomotor.
2.1.4 Installation Orientation
Servomotor can be installed ethier horizontally or vertically.
2.1.5 Handling Oil and Water
If the servomotor is used in a location that is subject to water or oil drops, make sure of the servomotor protective
specification. If the servomotor is required to meet the protective specification to the through shaft section by default,
use a servomotor with an oil seal.
Through shaft section:

It refers to the gap where the shaft protrudes from the end of the servomotor.
Through Shaft Section
- 24 -
2.1.6 Cable Tension
When connecting the cables, the bending radius should not be too small, do not bend or apply tension to cables.
Since the conductor of a signal cable is very thin (0.2 mm or 0.3 mm), handle it with adequate care.
2.1.7 Install to the Client
When the servo motor is mounted to the client, please firmly secure the servo motor by the screws with backing ring
as shown in the figure.
In
or stall
i en at
tat ion
io
n
2.2 Servo Drive
ProNet series servo drive is a base-mounted type. Incorrect installation will cause problems. Always observe the
installation instructions described below.
2.2.1 Storage
When the servomotor is not being used, store it in an area with a temperature between -25℃ and 55℃ with the
power cable disconnected.
2.2.2 Installation Sites
Notes on installation are shown below.

Situation Notes on installation
When installed in a control Design the control panel size, unit layout, and cooling method so that the temperature
panel around the periphery of the servo drive does not exceed 55℃.
Suppress radiation heat from the heating unit and a temperature rise caused by
When installed near a
convection so that the temperature around the periphery of the servo drive does not
heating unit
exceed 55℃.
When installed near a
Install a vibration isolator underneath the servo drive to prevent it from receiving vibration.
source of vibration
When installed in a location Take appropriate action to prevent corrosive gases. Corrosive gases do not immediately
subject to corrosive gases affect the servo drive, but will eventually cause contactor-related devices to malfunction.
Avoid installation in a hot and humid site or where excessive dust or iron powder is
Others
present in the air.
- 25 -
2.2.3 Installation Orientation
Install the servo drive perpendicular to the wall as shown in the figure. The servo drive must be oriented this way
because it is designed to be cooled by natural convection or a cooling fan if required. Firmly secure the servo drive
through two mounting holes.
2.2.4 Installation Method
When installing multiple servo drives side by side in a control panel, observe the following installation method.
Colling Fan Colling Fan

Cooling Fan Cooling Fan
■Installation Orientation
Install servo drive perpendicular to the wall so that the front panel (containing connectors) faces outward.
■Cooling
Provide sufficient space around each servo drive to allow cooling by natural convection or fans.
■Installing side by side
When installing servo drives side by side, provide at least 10mm space between each individual servo drive and at
least 50mm space above and below each one as well as shown in the figure above. Ensure the temperature inside the
control panel is evenly distributed, and prevent the temperature around each servo drive from increasing excessively.
- 26 -
Install cooling fans above the servo drives if necessary.
■Working conditions
1.Temperature：-20~ 55℃
2.Humidity：5%~95%RH
2
3.Vibration：4.9m/s or less
4.Ambient temperature to ensure long-term reliability: 45℃ or less
5.Condensation and Freezing: None
- 27 -
Chapter 3
Wiring
3.1 Main Circuit Wiring
Please observe the following instructions while wiring the main circuit.
· Do not bundle or run power and signal lines together in the same duct. Keep power and signal lines
separated by at least 300 mm.
· Use twisted-pair shielded wires or multi-core twisted-pair shielded wires for signal and encoder feedback
lines.
· The maximum length is 3 m for reference input lines and 20 m for encoder feedback lines.
· Do not touch the power terminals for 5 minutes after turning power OFF because high voltage may still
remain in the servo drive.
3.1.1 Names and Functions of Main Circuit Terminals
Servo Servo
Main
Terminal Drive Drive
Name Circuit Functions
Symbol Model Model
Voltage(V)
ProNet- Pronet-E-
100 02B-08B 02B-08B Single-phase 100～120VAC +10%～-15% (50/60Hz)
Main circuit 200 02A-04A 02A-04A Single-phase 200～230VAC +10%～-15% (50/60Hz)

L1,L2 power supply 200 08A-50A 08A-50A Three-phase 200～230VAC +10%～-15% (50/60Hz)
input terminal 10D-75D 10D-50D Three-phase 380～480VAC +10%～-15% (50/60Hz)
400
1AD-2BD － Three-phase 380～440VAC +10%～-15% (50/60Hz)
FG FG 200 02A-04A 02A-04A Normally not connected.
Servomotor
U,V,W connection －－－ Connect to the servomotor.
terminals
100 02B-08B 02B-08B Single-phase 100～120VAC +10%～-15% (50/60Hz)
Control circuit
L1C,L2C 200 02A-50A 02A-50A Single-phase 200～230VAC +10%～-15% (50/60Hz)
power supply
input terminal 1AD-2BD － Single-phase 380～440VAC +10%～-15% (50/60Hz)
400
24V,GND 10D-75D 10D-50D 24VDC +10%～-10%
Connects to the power supply ground terminals and
Ground terminals －－－
servomotor ground terminal.
External 100 02B 02B Connect an external regenerative resistor(provided
B1,B2,B3
regenerative 200 02A-04A 02A-04A by customer) between B1 and B2.
- 28 -
Servo Servo
Main
Terminal Drive Drive
Name Circuit Functions
Symbol Model Model
Voltage(V)
ProNet- Pronet-E-
resistor 100 04B-08B 04B-08B If using an internal regenerative resistor, please short
connection 200 08A-50A 08A-50A B2 and B3. Remove the wire between B2 and B3 and
terminal connect an external regenerative resistor(provided
10D-75D 10D-50D by customer) between B1 and B2, if the capacity of
400 the internal regenerative resistor is insufficient.
Connect an external regenerative resistor between
B1,B2 1AD-2BD －
B1 and B2.
DC reactor for Normally short ○
+ 1and ○+ 2.
200 02A-50A 02A-50A
harmonic If a countermeasure against power supply harmonic
+ 1,○
○ +2
suppression waves is needed, connect a DC reactor between ○
+
400 10D-75D 10D-50D
terminal 1and ○
+ 2.
Main circuit 200 02A-50A 02A-50A Normally not connected.
○
-
minus terminal 400 10D-75D 10D-50D
3.1.2 Typical Main Circuit Wiring Examples
 Single-phase 200V ProNet-02A～04A/ Single-phase 200V ProNet-E-02A～04A

L1 L2 Single-phase 200~230V+-10%
15% (50/60Hz)
Molded-case Circuit Breaker
Surge Protector
1Ry 1PL (Servo Alarm Display)
Noise Filter
Power OFF Power ON
1KM
1KM 1Ry 1SUP Be sure to connect a surge suppressor to the

excitation coil of the magnetic contactor and relay.
Magnetic Contactor
L1
A(1) Servodrive
L2 ProNet U
Series Servodrive V
B(2)
M
C(3)
1 W
D(4)
2
L1C
L2C
Encoder
CN2 PG
External regenerator resistor
B1
B1
B2
B2
B3
B3
1Ry +24V
7 ALM+
8 ALM-
1D
Ground Terminal 0V
Note
1.The L1,L2,L3 and L1C,L2C terminals wiring method of ProNet-02A～04A/ProNet-E-02A～04A servo drives is different
from other ProNet series servo drives. Please note the specific terminal definition while wiring.
2.The main circuit power supply of ProNet-02A～04A/ProNet-E-02A～04A is Single-phase 200V
- 29 -
3. External regenerative resistor for ProNet-02A～04A/ProNet-E-02A～04A is provided by customer, the model of 60W，
50Ωresistor is recommended.
4.Change Pn521.0 from “1” to “0” when using the external regenerative resistor in ProNet-02A～04A/ProNet-E-02A～04A
servo drives.
 ·Three-phase 200V ProNet-08A～50A/ Three-phase 200V ProNet-E-08A～50A

+10%
L1 L2 L3 Three-phase 200~230V -15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

excitation coil of the magnetic contactor and relay. .
Magnetic Contactor
L1
Servomotor
L2
ProNet U
A(1)
Series Servodrives B(2)

L3 V M
C(3)
1 W
D(4)
2
L1C
L2C
Encoder
CN2 PG
B1 B1
B2 B2
External Regenerator Resistor
B3 B3
+24V
1Ry
7 ALM+
8 ALM-
1D
Ground Terminal 0V
 Three-phase 400V ProNet-10D～75D/ Three-phase 400V ProNet-E-10D～50D

+10%
L1 L2 L3 Three-phase 380~440V -15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

excitation coil of the magnetic contactor and relay..
Magnetic Contactor
L1
Servomotor
L2
ProNet U
A(1)
Series Servodrives B(2)

L3 V M
C(3)
1 W
D(4)
2
24V
24VDC Power Supply
GND
Encoder
CN2 PG
B1 B1
B2 B2
External Regenerator Resistor
B3 B3
+24V
1Ry
7 ALM+
8 ALM-
1D
Ground Terminal 0V
- 30 -
 Three-phase 400V ProNet-1AD～2BD
L1 L2 L3 Three-phase 380~440V +-10%

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM
1KM 1Ry 1SUP Be sure to connect a surge

suppressor to the excitation coil of
the magnetic contactor and relay.
Magnetic Contactor
L1
A(1) Servodrive
L2 ProNet U
L3 Series Servodrive V
B(2)
M
C(3)
W
D(4)
L 1C
L2C
Encoder
CN2 PG
External Regenerative Resistor

B1
B2
1Ry +24V
7 ALM+
8 ALM-
1D
Ground Terminal 0V
Notes:
1. A resistor value of 1500W/20Ω is recommended for the external regenerative resistor of ProNet-1AD.
2. A resistor value of 1500W/15Ω is recommended for the external regenerative resistor of ProNet-1ED.
3. A resistor value of 1500W/20Ω is recommended for the external regenerative resistor of ProNet-2BD.
 Single-phase 100V ProNet-02B /Single-phase 100V ProNet-E-02B
L1 L2 +10%
Single-phase 100~120V -15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
A(1) Servodrive
U
L2
B(2)
V M
C(3)
1 W
D(4)
2
L1C
L2C
Encoder
CN2 PG
B1
B1
B2
B2
B3
B3
1Ry +24V
7 ALM+
8 ALM-
1D
Ground Terminal 0V
- 31 -
L1 L2 +10%
Single-phase 100~120V -15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
A(1) Servodrive
U
L2
B(2)
V M
C(3)
1 W
D(4)
2
L1C
L2C
Encoder
CN2 PG
B1
B1
B2
B2
B3
B3
1Ry +24V
7 ALM+
8 ALM-
1D
Ground Terminal 0V
L1 L2 +10%
Single-phase 100~120V -15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
A(1) Servodrive
U
L2
B(2)
V M
C(3)
1 W
D(4)
2
L1C
L2C
Encoder
CN2 PG
B1
B1
B2
B2
B3
B3
1Ry +24V
7 ALM+
8 ALM-
1D
Ground Terminal 0V
Notes:
When single-phase 100VAC is provided for main circuit on rated speed, instantaneous peak torque≤4.78 N.m.
When three-phase 100VAC is provided for main circuit on rated speed, instantaneous peak torque≤7.16 N.m.
- 32 -
3.2 I/O Signals
3.2.1 Examples of I/O Signal Connections
ProNet
Series Servodrive
10K
40K ref
VREF+ 1 +
Speed Reference(±0~10V/Rated Speed)
P
40K
VREF- 2 -
20 PAO+
10K
ref
A/D 21 PAO-
TREF+ 26 + 22 PBO+
Torque Reference(±0~10V/Rated Torque) PG Divided Ratio Output
P
TREF- 27 -
23 PBO- Applicable Line Output
24 PCO+ AM26LS32A Manufactured by TI or the Equivalent.
25 PCO-
50 DGND
Open-Collector Reference PPI 34

Use 2KΩ
150Ω
PULS+ 30
P
Position Reference PULS / CW / A PULS- 31

2KΩ
150Ω
SIGN+ 32
SIGN / CCW / B
P
SIGN- 33
Signal Allocations can be Modified:

5 TGON+ V-CMP: Speed Coincidence
COIN: Positioning Completion
6 TGON- TGON:Rotation Detection
9 S-RDY+ S-RDY:Servo Ready
CLT:Torque Limit Detection
10 S-RDY- BK:Brake Interlock
11 V-CMP+ PGC: Encoder C-Pulse Output
OT: Over Travel
12 V-CMP- RD: Servo Enabled Motor Excitation Output
HOME: Home Completion Output
+24V
DICOM 13
Signal Allocations can be Modified: 3.3KΩ
S-ON 14
S-ON: Servo ON
P-CON 15
P-CON: Proportion Control
P-OT 16
P-OT:Forward Run Prohibited
N-OT 17
N-OT:Reverse Run Prohibited
ALM-RST 39
ALM-RST: Alarm Reset
CLR 40
CLR: Clear Error Pulse P-CL 41
P-CL:Forward Torque Limit N-CL 42
N-CL:Reverse Torque Limit
SHOM: Home
ORG: Zero Position
1Ry +24V
7 ALM+
Shield 8 ALM-
Connect Shield to Connector Shell
1D
0V
ALM: Servo Alarm Output
Photocoupler Output:
Represents Twisted-pair Wires Maximum Operating Voltage:DC30V
P
Maximum Output Current:DC50mA
- 33 -
3.2.2 I/O Signal Names and Functions
 Input Signals
Control Signal Pin
Function
Mode Name No.
/S-ON 14 Servo ON: Turns the servomotor on.
Function selected by parameter.
Proportional Switches the speed control loop from PI to P control when
control reference ON.
Direction With the internally set speed selection: Switch the rotation
reference direction.
/P-CON 15 Control mode

Enables control mode switching.
switching
Zero-clamp Speed control with zero-clamp function: Reference speed is

reference zero when ON.
Reference pulse Position control with reference pulse: Stops reference pulse
block input when ON.
Speed Forward run
Position P-OT 16 prohibited
Torque Overtravel prohibited: Stops servomotor when OFF.
N-OT 17 Reverse run
prohibited
Function selected by parameter.
Forward external
torque limit ON
/PCL 41 Current limit function enabled when ON.
Reverse external
/NCL 42 torque limit ON
Internal speed With the internally set speed selection: Switches the internal
switching speed settings.
/ALM-RST 39 Alarm reset: Releases the servo alarm state.

DICOM 13 Control power supply input for I/O signals: Provide the +24V DC power supply
VREF+ 1
Speed Speed reference input: ±10V.
VREF- 2
PULS+ 30
Pulse reference input mode：
PULS- 31 Sign + pulse train
CCW + CW pulse
SIGN+ 32
Two-phase pulse (90º phase differential)
SIGN- 33
Power supply input for open collector reference (2KΩ/0.5W resistor is built into the
Position PPI 34
servo drive).
Positional error pulse clear input: Clear the positional error pulse during position
/CLR 40
control.
SHOM - Homing trigger signal(effective at the rising edge),allocated by Pn509 or Pn510
ORG - Zero Position(effective at high level), allocated by Pn509 or Pn510
T-REF+ 26
Torque Torque reference input: ±10V.
T-REF- 27
- 34 -
 Output signals
Control
Signal
Mode Pin No. Function
Name
/TGON+ 5 Detects when the servomotor is rotating at a speed higher than the motor
/TGON- 6 speed seeting.
ALM+ 7 Servo alarm:
ALM- 8 Turns off when an error is detected.
/S-RDY+ 9 Servo ready:
ON if there is no servo alarm when the control/main circuit power supply
/S-RDY- 10
Speed is turned ON.
Position PAO+ 20
Phase-A signal
Torque PAO- 21 Converted two-phase pulse(phases A and B)
PBO+ 22 encoder output.
Phase-B signal
PBO- 23
PCO+ 24
Phase-C signal Zero-point pulse(Phase-C) signal
PCO- 25
Connect frame to ground if the shield wire of the
FG Shell
I/O signal cable is connected to the connector shell.
/V-CMP+ 11 Speed coincidence:

Speed Detects whether the motor speed is within the setting range and if it
/V-CMP- 12 matches the reference speed value.
Positioning completion:
/COIN+ 11
Turns ON when the number of positional error pulses reaches the value
Position
set. The setting is the number of positional error pulses set in the
/COIN- 12
reference units.
Reserved terminals:
The functions allocated to /TGON, /S-RDY, and /V-CMP (/COIN) can be
/CLT changed by using the parameters.
/CLT: Torque limit output
Turns on when it reaches the value set.
— /BK: Brake interlock output
Releases the brake when ON,
Reserved
/PGC：C pulse output
/BK OT：Over travel signal output
/RD：Servo enabled motor excitation output
/HOME: Home completion output
4,18,19,29,35
— 36,37,38,43 Not used.
44,45,47,49
- 35 -
3.2.3 I/O Signal Connector (CN1) Terminal Layout
Terminal Terminal
Name Function Name Function
No. No.
1 VREF+ 26 T-REF+
Speed reference input:±10V Torque referenceinput:±10V
2 VREF- 27 T-REF-
3 DGND DGND 28 DGND DGND
4 — Reserved 29 — Reserved
5 /TGON+ 30 PULS+
Running signal output Reference pulse input
6 /TGON- 31 PULS-
7 ALM+ 32 SIGN+
Servo alarm Reference sign input
8 ALM- 33 SIGN-
Open collector reference
9 /S-RDY+ 34 PPI
Servo ready power supply
10 /S-RDY- 35 — Reserved
11 /COIN+ 36 — Reserved
Positioning completion
12 /COIN- 37 — Reserved
I/O signal power supply 24V
13 DICOM 38 — Reserved
DC
14 /S-ON Servo ON 39 /ALM-RST Alarm reset
15 /P-CON P/PI control input 40 /CLR Position error pulse clear input
16 P-OT Forward run prohibited 41 /PCL Forward torque limit input
17 N-OT Reverse run prohibited 42 /NCL Reverse torque limit input
20 PAO+ PG dividing 45 — Reserved
pulse output PG
21 PAO- 46 DGND DGND
phase A dividing
22 PBO+ PG dividing pulse 47 — Reserved
pulse output output
23 PBO- 48 DGND DGND
phase B
24 PCO+ PG dividing 49 — Reserved
Zero-point
pulse output
25 PCO- pulse 50 DGND DGND
phase C
Note: The functions allocated to the following input and output signals can be changed by using the parameters.
·Input signals: /S-ON,/P-CON,P-OT,N-OT,/ALM-RST,/CLR,/PCL,/NCL,SHOM,ORG
·Output signals: /TGON,/S-RDY,/COIN,/HOME
Please refer to A.3 Parameters in details for detailed information.
- 36 -
3.2.4 Interface Circuit
This section shows examples of servo drive I/O signal connection to the host controller.
■Interface for Analog Reference Input Circuit
Analog signals are either speed or torque reference signals at about 40kΩ impedance, and the maximum allowable
voltages for input signals is ±10V.
Reference speed input Reference torque input

Servodrive
470Ω(1/2W)min.
10V 2 V-REF
2KΩ
About 40KΩ
1
GND
0V
■Interface for sequence input circuit
The sequence input circuit interface connects through a relay or open-collector transistor circuit. Select a low-current relay
otherwise a faulty contact will result.
■Interface for line driver output circuit
The amount of two-phase (phase A and phase B) pulse output signals (PAO,/PAO,PBO,/PBO) and zero-point pulse
signals (PCO,/PCO) are output via line-driver output circuits. Normally, the servo drive uses this output circuit in speed
control to comprise the position control system at the host controller. Connect the line-driver output circuit through a line
receiver circuit at the host controller.
■Interface for sequence output circuit
Photocoupler output circuits are used for Servo Alarm (ALM), Servo Ready(S-RDY), and other sequence output signal
circuits. Connect a photocoupler output circuit through a relay circuit.
- 37 -
3.3 Wiring Encoders
3.3.1 Connecting an Encoder(CN2)
■ Wire-saving Incremental Encoder（2500P/R）（Waterproof）

Wire-saving Incremental
Encoder Servodrive Host controller
*
2CN 1CN
*
1(A) PA 2-1
Phase-A 20 PAO
2(B) P /PA 2-2
21 /PAO P
3(C) PB 2-3
4(D) P /PB 2-4 Phase-B 22 PBO
5(E) PC 2-5
23 /PBO P
6(F) P /PC 2-6
Phase-C 24 PCO
25 /PCO P
PG
Output line driver
Applicable line-
AM26LS31 manufactured
receiver SN75175
by TI or the equivalent.
manufactured by TI
or the equivalent.
7(H) 2-7、2-8、2-9
PG5V
8(G) 2-17、2-18、2-19
PG0V
1-18 SG
0V 0V
1-36
FG Connector shell
9(J)
Connector shell
（Shell）
shielded wires
* P Represents multi-core twisted pair shielded wires.
■ Wire-saving Incremental Encoder（2500P/R）（Standard）

Wire-saving Incremental
Encoder Servodrive Host controller
*
2CN 1CN
*
1(A) PA 2-1
Phase-A 20 PAO
4(B) P /PA 2-2
21 /PAO P
2(C) PB 2-3
5(D) P /PB 2-4 Phase-B 22 PBO
3(E) PC 2-5
23 /PBO P
6(F) P /PC 2-6
Phase-C 24 PCO
25 /PCO P
PG
Output line driver
Applicable line-
receiver SN75175
by TI or the equivalent.
manufactured by TI
or the equivalent.
7(H) 2-7、2-8、2-9
PG5V
8(G) 2-17、2-18、2-19
PG0V
1-18 SG
0V 0V
1-36
9(J) FG Connector shell

Connector shell
（Shell） shielded wires
- 38 -
 17 bit Incremental/Absolute Encoders

Incremental/Absolute Encoders Servodrive Host controller
*
CN2 CN1
*
K(1) PS 7
Phase-A 20 PAO
L(2) P /PS 8
21 /PAO P
T(3) BAT+ 17
S(4) P BAT- 18 Phase-B 22 PBO
23 /PBO P
Phase-C 24 PCO
25 /PCO P
PG
Output line driver
by TI or the equivalent. Applicable line-
receiver SN75175
manufactured by TI
or the equivalent.
H(5) PG5V 9
G(6) PG0V 19
50 DGND
0V 0V
J(7) FG Connector shell

shielded wires Connector shell
（Shell）
* P
Represents multi-core twisted pair shielded wires.
Note: (1)BAT+ and BAT- signals are not used when using an incremental encoder .
(2)The pin numbers for the connector wiring differ depending on the servomotors .
 Resolver
Resolver Servodrive Host controller

*
CN2 CN1
*
K SIN+ 7
Phase-A 20 PAO
L P SIN- 8
21 /PAO P
T COS+ 17
S P COS- 18 Phase-B 22 PBO
23 /PBO P
Phase-C 24 PCO
25 /PCO P
PG Output line-driver
AM26LS31
manufactured by TI Applicable line-
or equivalent. receiver SN75175
manufactured by
TI or equivalent.
H R1 9
G R2 19
50 DGND
0V 0V
FG Connect shell
J
shielded wires Connector shell
Shell
- 39 -
3.3.2 Encoder Connector(CN2) Terminal Layout
 Wire-saving Incremental Encoder（2500P/R）
Terminal No. Name Function Terminal No. Name Function

1 PA PG input phase A 5 PC PG input phase B
2 /PA PG input phase /A 6 /PC PG input phase /B
3 PB PG input phase B 7,8,9 PG5V PG power supply +5V
4 /PB PG input phase /B 17,18,19 SG PG power supply 0V
 17 Bit Incremental/ Absolute Encoder

Battery(+)
7 PS PG serial signal input 17 BAT+
(For an absolute encoder)
Battery(-)
8 /PS PG serial signal input 18 BAT-
(For an absolute encoder)
9 PG5V PG power supply +5V 19 GND PG power supply 0V
 Resolver
7 SIN+ Differential Sine Signal 17 COS+ Differential Cosine Signal
8 SIN- Differential Sine Signal 18 COS- Differential Cosine Signal
9 R1 Excitation signal 19 R2 Excitation Signal
3.4 Communication Connection
3.4.1 Communication Connector(CN3) Terminal Layout
Terminal No. Name Function

1 —
Reserved
2 —
3 485+ RS-485 communication terminal
4 ISO_GND
Isolated ground
5 ISO_GND
6 485- RS-485 communication terminal
7 CANH CAN communication terminal
8 CANL CAN communication terminal
Note: Do not short terminal 1 and 2 of CN3.
- 40 -
3.4.2 Communication Connector(CN4) Terminal Layout

1 —
Reserved
2 —
4 ISO_GND
Isolated ground
5 ISO_GND
- 41 -
3.5 Standard Wiring Examples
3.5.1 Single-phase 200V ProNet-02A～04A/ProNet-E-02A～04A
L1 L2 single-phase 200~230V +10%

-15% (50/60Hz)
Surge Protector
1Ry 1PL (Servo Alarm Display )
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
ProNet Servomotor
A(1)
L1 Series Servodrives U
B(2)
L2 V M
C(3)
1 W
D(4)
2
CN2
Option
L1 C
Incremental Wire-saving
L2C Encoder（2500P/R） Serial Encoder
1 A+ Encoder
2 A- 7 S+
External Regenerator Resistor 3 B+ 8 S-
B1 4 B- 17 BAT+ PG
B1 5 C+ 18 BAT-
B2 6 C- 9 PG5V
B2 PG5V
7,8,9
19 PG0V
B3 17,18,19 PG0V
B3 Shell Shield
Shell Shield
CN3
1 N.C. Be sure to prepare the end of the

Be sure to ground N.C. shielded wire properly.
2
3 485+
CN1 4 ISO_GND
5 ISO_GND Use special communication cable to connect
10K
40K ref 6 485- PC(Personal Computer).
VREF+ 1 +
7 CANH
P
40K
Speed Reference(±0~10V/Rated Speed) VREF- 2 -
10K A/D
8 CANL Note: Do not short terminal 1 and 2 of CN3.
ref
TREF+ 26 + Shell Shield
P
Torque Reference (±0~10V / Rated Torque) TREF- 27 -
CN4
1 N.C.
2 N.C.
Open-collector Reference Use
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P
Position Reference PULS- 31 6 485-

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
Signal allocatons can be modified: DICOM 13 20 PAO+
3.3KΩ
S-ON: Servo ON S-ON 14 21 PAO-
P-CON: P Control P-CON 15 22 PBO+ PG Divided Ratio Output:
P-OT: Forward Run Prohibited P-OT 16 23 PBO- Applicable Line Receiver
AM26LS32A Manufactured by TI or the Equivalent.
N-OT: Reverse Run Prohibited N-OT 17 24 PCO+
ALM-RST: Alarm Reset ALM-RST 39 25 PCO-
CLR: Clear Error Pulse CLR 40 50 DGND
P-CL: Forward Torque Limit P-CL 41
N-CL: Reverse Torque Limit N-CL 42 Signal Allocations can be Modified:
V-CMP: Speed Coincidence
SHOM: Home 5 TGON+ COIN: Positioning Completion
ORG: Zero Position 6 TGON- TGON:Rotation Detection
S-RDY:Servo Ready
9 S-RDY+ CLT:Torque Limit Detection
OT:Over Travel
1Ry +24V
7 ALM+
Connect Shield to Connector Shell. Shield Shell
8 ALM-
1D
0V
Represents Twisted-pair Wires

P
Maximum Operating Voltage:DC30V
Note 1.The L1,L2,L3 and L1C,L2C terminals wiring method of ProNet-02A～04A/ProNet-E-02A～04A servo drives is
different from other ProNet series servo drives. Please note the specific terminal definition while wiring.
2.The main circuit power supply of ProNet-02A～04A/ProNet-E-02A～04A is Single-phase 200V
3. External regenerative resistor for ProNet-02A～04A/ProNet-E-02A～04A is provided by customer, the model of
60W，50Ωresistor is recommended.
4.Change Pn521.0 from “1” to “0” when using the external regenerative resistor in ProNet-02～04/ProNet-E-02A～
04A servo drives.
- 42 -
3.5.2 Three-phase 200V ProNet-08A～50A/ProNet-E-08A～50A
L1 L2 L3 Three-phase 200~230V +10%

-15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
ProNet Servomotor
A(1)
B(2)
L3 V M
C(3)
1 W
D(4)
2
CN2
Option
L1C
L2C Incremental Wire-saving Serial Encoder

Encoder（2500P/R） Encoder
7 S+
B1 B1 1 A+ Resolver
2 A- 8 S-
7 SIN+ 17 BAT+ PG
B2 B2 3 B+
8 SIN- 18 BAT-
External Regenerator Resisotr 4 B-
17 COS+
5 C+ 9 PG5V
B3 B3 18 COS-
6 C- 19 PG0V
9 R1
7,8,9 PG5V 19 R2 Shell Shield
17,18,19 PG0V
Shell Shield
Shell Shield
Be sure to ground CN3

2 N.C. shielded wire properly.
3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
10K A/D
ref
P
Torque Reference (±0~10V/Rated Torque) TREF- 27 -
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
Open-collector Reference Use 2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
- 43 -
3.5.3 Three-phase 400V ProNet-10D～75D/ProNet-E-10D～50D

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
ProNet Servomotor
A(1)
B(2)
L3 V M
C(3)
1 W
D(4)
2
CN2
Option
24V
24VDC Power Supply
GND Encoder（2500P/R）
Serial Encoder
Encoder
1 A+ Resolver 7 S+
B1 B1
2 A- 8 S-
7 SIN+
3 B+ 17 BAT+ PG
B2 B2 8 SIN-
4 B- 18 BAT-
External Regenerator Resisotr 17 COS+
5 C+ 9 PG5V
B3 B3 18 COS-
6 C-
9 R1 19 PG0V
7,8,9 PG5V 19 R2
17,18,19 PG0V Shell Shield
Shell Shield
Shell Shield

3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
10K A/D
ref
P
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
- 44 -
3.5.4 Three-phase 400V ProNet-1AD～2BD

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Magnetic Contactor
L1
ProNet Servomotor
A(1)
B(2)
L3 V M
C(3)
W
D(4)
CN2
L1C
Option
Resolver
L2C Serial Encoder
1 Sensor 1 Encoder
3 Sensor 2 7 S+
B1 7 SIN+ 8 S-
8 SIN- 17 BAT+ PG
B2 17 COS+
External Regenerator Resisotr 18 BAT-
18 COS-
9 R1
9 PG5V
19 R2 19 PG0V
Shell Shield Shell Shield

3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
8 CANL
10K
ref
A/D Note: Do not short terminal 1 and 2 of CN3.
P
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
Signal allocatons can be modified: +24V DICOM 13 20 PAO+

3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
Notes:
1. The resistor of 1500W/20Ω is recommended for the external regenerative resistor of ProNet-1AD.
2. The resistor of 1500W/15Ω is recommended for the external regenerative resistor of ProNet-1ED.
3. The resistor of 1500W/20Ω is recommended for the external regenerative resistor of ProNet-2BD.
- 45 -
3.5.5 Single-phase 100V ProNet-02B/ProNet-E-02B
L1 L2 single-phase 100~120V +-10%

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Servomotor
A(1)
L1 U
B(2)
L2 V M
C(3)
1 W
D(4)
2
CN2
Option
L1C Serial Encoder Encoder(2500P/R)
7 S+ 1 A+
L2C
8 S- 2 A- Encoder
17 BAT+ 3 B+
External Regenerator Resistor 18 BAT- 4 B-
B1 9 PG5V 5 C+ PG
B1
19 PG0V 6 C-
B2 7,8,9 PG5V
B2 Shell Shield 17,18,19 PG0V
B3 Shell Shield
B3
CN3

Be sure to ground shielded wire properly.
2 N.C.
3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
8 CANL
10K A/D Note: Do not short terminal 1 and 2 of CN3.
ref
P
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
- 46 -
3.5.6 Single-phase 100V ProNet-04B /ProNet-E-04B

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Servomotor
A(1)
L1 U
B(2)
L2 V M
C(3)
1 W
D(4)
2
CN2
L1C Option Encoder(2500P/R)
Serial Encoder 1 A+
L2C
2 A- Encoder
7 S+
3 B+
8 S-
4 B-
17 BAT+
5 C+ PG
B1 B1 18 BAT-
6 C-
9 PG5V
19 PG0V 7,8,9 PG5V
B2 B2
17,18,19 PG0V
External Regenerator Resisotr
B3 B3
CN3

2 N.C.
3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
10K A/D
ref
P
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
- 47 -
3.5.7 Single-phase 100V ProNet-08B/ ProNet-E-08B

15% (50/60Hz)
Surge Protector
Noise Filter
Power OFF Power ON
1KM

Servomotor
A(1)
L1 U
B(2)
L2 V M
C(3)
1 W
D(4)
2
CN2
L1C Option Encoder(2500P/R)
Serial Encoder 1 A+
L2C
2 A- Encoder
7 S+
3 B+
8 S-
4 B-
17 BAT+
5 C+ PG
B1 B1 18 BAT-
6 C-
9 PG5V
19 PG0V 7,8,9 PG5V
B2 B2
17,18,19 PG0V
External Regenerator Resisotr
B3 B3
CN3

2 N.C.
3 485+
CN1 4 ISO_GND
10K
VREF+ 1 +
7 CANH
P
40K
10K A/D
ref
P
CN4
1 N.C.
2 N.C.
PPI 34 3 485+
2KΩ
4 ISO_GND
150Ω
PULS+ 30 5 ISO_GND
PULS / CW / A
P

2KΩ
7 CANH
150Ω
SIGN+ 32 8 CANL
SIGN / CCW / B
P
SIGN- 33
Shell Shield
+24V
3.3KΩ
S-RDY:Servo Ready
OT:Over Travel
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
Notes:
When single-phase 100VAC is provided for main circuit on rated speed, instantaneous peak torque≤4.78 N.m.
When three-phase 100VAC is provided for main circuit on rated speed, instantaneous peak torque≤7.16 N.m.
- 48 -
3.5.8 Position Control Mode
ProNet
Series Servodrives
20 PAO+
21 PAO-
22 PBO+ PG Divided Ratio Output:
Applicable Line Receiver
23 PBO- AM26LS32A Manufactured by TI or the Equivalent.
24 PCO+
25 PCO-
50 DGND
Open-collector Reference Use PPI 34

2KΩ
150Ω
PULS / CW / A
PULS+ 30
Position Reference
P
PULS- 31
2KΩ
150Ω
SIGN / CCW / B
SIGN+ 32
P
SIGN- 33

9 S-RDY+ S-RDY:Servo Ready
10 S-RDY- CLT:Torque Limit Detection
BK:Brake Interlock
11 COIN+ PGC: Encoder C-Pulse Output
12 COIN- OT:Over Travel
RD: Servo Enabled Motor Excitation Output
+24V
Signal allocatons can be modified: DICOM 13 3.3KΩ
S-ON: Servo ON S-ON 14
P-CON: P Control P-CON 15
P-OT: Forward Run Prohibited P-OT 16
N-OT: Reverse Run Prohibited N-OT 17
ALM-RST: Alarm Reset ALM-RST 39
CLR: Clear Error Pulse CLR 40
N-CL: Reverse Torque Limit N-CL 42
SHOM: Home
ORG: Zero Position
1Ry +24V
7 ALM+
8 ALM-
1D
0V

P
- 49 -
3.5.9 Speed Control Mode
ProNet
Series Servodrives
10K
ref
20 PAO+
40K
Speed Reference(±0~10V/Rated Speed) VREF+ 1 + 21 PAO-
P
40K
VREF- 2 -
10K A/D 23 PBO- AM26LS32A Manufactured by TI or the Equivalent.
24 PCO+
25 PCO-
50 DGND

5 TGON+ COIN: Positioning Completion
TGON:Rotation Detection
6 TGON- S-RDY:Servo Ready
PGC: Encoder C-Pulse Output
11 V-CMP+ OT:Over Travel
+24V 12 V-CMP- RD: Servo Enabled Motor Excitation Output
DICOM 13 HOME: Home Completion Output
Signal allocatons can be modified: 3.3KΩ
S-ON 14
S-ON: Servo ON
P-CON 15
P-CON: P Control
P-OT 16
P-OT: Forward Run Prohibited
N-OT 17
N-OT: Reverse Run Prohibited
ALM-RST 39
ALM-RST: Alarm Reset
CLR 40
CLR: Clear Error Pulse
P-CL 41
P-CL: Forward Torque Limit
N-CL 42
N-CL: Reverse Torque Limit
SHOM: Home
ORG: Zero Position
1Ry +24V
7 ALM+
8 ALM-
1D
0V
P
- 50 -
3.5.10 Torque Control Mode
ProNet
Series Servodrives
20 PAO+
21 PAO-
23 PBO- AM26LS32A Manufactured by TI or the Equivalent.
A/D 24 PCO+
ref
TREF+ 26 + 25 PCO-
Torque Reference (±0~10V/Rated Torque)
P
TREF- 27 - 50 DGND

+24V
Signal allocatons can be modified: DICOM 13 9 S-RDY+ S-RDY:Servo Ready
S-ON 14
3.3KΩ
10 S-RDY- CLT:Torque Limit Detection
S-ON: Servo ON BK:Brake Interlock
P-CON: P Control P-CON 15 11 V-CMP+ PGC: Encoder C-Pulse Output
P-OT 16 12 V-CMP- OT:Over Travel
P-OT: Forward Run Prohibited RD: Servo Enabled Motor Excitation Output
N-OT: Reverse Run Prohibited N-OT 17 HOME: Home Completion Output
ALM-RST: Alarm Reset ALM-RST 39
CLR 40
CLR: Clear Error Pulse
P-CL 41
P-CL: Forward Torque Limit
N-CL 42
N-CL: Reverse Torque Limit
SHOM: Home
ORG: Zero Position
1Ry +24V
7 ALM+
Connect Shield to Connector Shell. 8 ALM-
Shield Shell 1D
0V
P
- 51 -
3.6 Wiring for Noise Control
3.6.1 Noise Control
The servo drive uses high-speed switching elements in the main circuit. It may receive "switching noise" from these
high-speed switching elements.
To prevent malfunction due to noise, take the following actions:
• Position the input reference device and noise filter as close to the servo drive as possible.
• Always install a surge absorber in the relay, solenoid and electromagnetic contactor coils.
• The distance between a power line (servomotor main circuit cable) and a signal line must be at least 30 cm. Do not put
the power and signal lines in the same duct or bundle them together.
• Do not share the power supply with an electric welder or electrical discharge machine. When the servo drive is placed
near a high-frequency generator, install a noise filter on the input side of the power supply line. As for the wiring of noise
filter, refer to (1) Noise Filter shown below.
• For proper grounding technique, refer to (2) Correct Grounding.
(1) Noise Filter

Please install a noise filter in the appropriate place to protect the servo drive from external noise interference.
Notice：
Noise filter *3 Servo Drive

Servomotor
AC 200V L1
M
AC 400V L2 (FG)
L3
3.5mm2 min. *1 
 CN2 PG

CN1
2
2mm min.
Operation relay sequence
Signal generation circuit
*3 *2
Noise DC
filter power
3.5mm2 min.
(ground plate) (ground plate) (ground 3.5mm2 min. *1

plate)
Wires of
3.5mm2 min. *1 (ground plate)
(ground plate)
Ground: Ground to an independent ground

use ground resistor 100Ω max.
2
•For ground wires connected to the ground plate, use a thick wire with a thickness of at least 3.5 mm (preferably, plain
stitch cooper wire)
• should be twisted-pair wires.
•When using a noise filter, follow the precautions in 3.6.2 Precautions on Connecting Noise Filter.
- 52 -
(2) Correct Grounding

Take the following grounding measures to prevent the servo drive from malfunctioning due to noise.
￭ Grounding the Motor Frame
If the servomotor is grounded via the machine, a switching noise current will flow from the servo drive main circuit through
the servomotor stray capacitance.
Always connect servomotor frame terminal FG to the servo drive ground terminal. Also be sure to ground the ground
terminal .
￭ Noise on the I/O Signal Line
If the I/O signal line receives noise, ground the 0 V line (SG) of the reference input line. If the main circuit wiring for the
motor is accommodated in a metal conduit, ground the conduit and its junction box. For all grounding, ground at one point
only.
（3）Precautions on installing on the control panel

￭When the servo drive is installed on the control panel, a piece of metal plate should be fixed. It is used for fixing the servo
drive and other peripheral devices. The noise filter should be installed on the metal plate, and closed to the hole drill
through power lines on control panel. Use screws to fix the noise filter to the metal plate. The grounding terminals of noise
filter connects to the grounding terminals of control panel.
￭ Servo drive should be fixed on a piece of metal plate. Make sure the heat sink towards ground. The grounding terminals
of servo drive connect to the grounding terminals of control panel.
3.6.2 Precautions on Connecting Noise Filter
(1) Noise Filter Brake Power Supply

Use the noise filter Manufactured by SCHAFFNER at the brake power input for servomotors with holding brakes.
Relationship between servo drive power and noise filter current:
Servo Drive Power Noise Filter Current

0.2kW 1A
0.4kW 2A
0.75kW 4A
1 kW 4A
1.5 kW 6A
2 kW 8A
3 kW 12A
5 kW 20A
7.5kW 30A
11kW 44A
15kW 60A
22kW 88A
- 53 -
Note:
1. A single-phase servomotor should apply a two-phase filter. A three-phase servo drive should apply a
three-phase filter.
2. Choose the right filter according the specifications of operating voltage, current, and manufacturer.
(2) Precautions on Using Noise Filters
Do not put the input and output lines in the same duct or bundle them together.
Noise Noise
Filter Filter
Ground plate Ground plate
Noise Noise
Filter Filter
Separate these circuits
Separate the noise filter ground wire from the output lines.
Do not accommodate the noise filter ground wire, output lines and other signal lines in the same duct or bundle them
together.
Noise Noise
Filter Filter
Connect the noise filter ground wire directly to the ground plate. Do not connect the noise filter ground wire to other
ground wires.
- 54 -
Noise Noise
Filter Filter
servodrive servodrive servodrive servodrive
stub
Shielded
ground wire
ground plate ground plate
If a noise filter is located inside a control panel, connect the noise filter ground wire and the ground wires from other
devices inside the control panel to the ground plate for the control panel first, then ground these wires.
Control Panel
Servodrive
Noise
Filter
Servodrive
Ground
Ground plate
3.7 Installation Conditions of EMC Directives
To adapt a combination of a servomotor and a servodrive to EMC Directives (EN61326-1:2006), the following conditions
must be satisfied.
(1) EMC Installation Conditions
This section describes the installation conditions that satisfy EMC guidelines for each servo drive model.
This section describes the EMC installation conditions satisfied in test conditions prepared by ESTUN. The actual EMC
level may differ depending on the actual system’s configuration, wiring, and other conditions.
- 55 -
Ground/Shield Box
Brake power
supply
Servo Drive
Brake
Clamp
U,V,W
Core
Power Supply
Core
Noise
Clamp
Three-phase 200VAC L1,L2,L3
4 filter 2 Servo-
Three-phase 400VAC
L1C,L2C motor
Core
Core
Clamp
Core
CN2 Encoder
3
PE Aprox.2m CN1
Core Aprox.5m PE
1
Core
Host controller
Symbol Cable Name Specifications

① I/O signal cable Shield cable
② Servomotor cable Shield cable
③ Encoder cable Shield cable
④ AC line cable Shield cable
Notes: The example above shows three-phase 200VAC servo drive connection.
(2) Cable Core and Cable Clamp
(a) Attaching the Ferrite Core
The diagram shows two turns in the cable.
The table shows the cable and the position where the ferrite core is attached.
Cable Cable Name Mounting Position of the Core

I/O signals cable Near the host controller and servodrive.
Ferrite core
Motor cable Near the servodrive and servomotor.
Encoder cable Near the servodrive and servomotor.
(b) Recommended Ferrite-core
Cable Name Ferrite Core Model Manufacturer

I/O signals cable
Encoder cable ESD-SR-25 TOKIN
Motor 400W or less
cable 750W or less PC40T96 × 20 × 70 TDK
- 56 -
(c) Fixing the Cable

Fix and ground the cable shield using a piece of conductive metal.
• Example of Cable Clamp
Cable Shield(cable sheath stripped)

Host controller side
Fix and ground the cable shield
using a piece of conductive metal.
Ground plate
Cable clamp
Remove paint on mounting surface
(d) Shield Box

A shield box, which is a closed metallic enclosure, should be used for shielding magnetic interference. The structure of the
box should allow the main body, door, and cooling unit to be attached to the ground. The box opening should be as small
as possible.
3.8 Using More than One Servo Drive
The following diagram is an example of the wiring when more than one Servodrive is used.
Connect the alarm output (ALM) terminals for the three Servodrives in series to enable alarm detection relay 1RY to
operate.
When the alarm occurs, the ALM output signal transistor is turned OFF.
Multiple servos can share a single molded-case circuit breaker (QF) or noise filter. Always select a QF or noise filter that
has enough capacity for the total power capacity (load conditions) of those servos.
- 57 -
Power supply
R S T
Power
Power ON
QF
OFF 1RY 1KM
1KM
Noise
filter
SA
1KM
L1 Servo Motor
L2 Servo Drive
L3
L1C M
L2C
+24 1RY CN1

ALM+
ALM-
L1 Servo Drive Servo Motor

L2
L3
L1C M
L2C
CN1
ALM+
ALM-
L1 Servo Drive Servo Motor

L2
L3
L1C M
L2C
CN1
ALM+
ALM-
0V
Notes:
1. Power supply phase-S should connect to ground terminals.
2. The example above shows three-phase 200VAC servo drive connection.
- 58 -
3.9 Connecting DC Bus
Servo drive wiring includes standard wiring （standard wiring refers to 3.5 Standard Wiring Examples） and optional
wiring. Connecting DC bus together of the optional wiring conduces to bus voltage more stable. The following diagram is
an example of the wiring when connecting more than one servo drive DC bus.
Notes:
Connecting DC bus together is available only for 200V ProNet and ProNet-E series servo drives. Please use the
wiring on ProNet-08A/10A, ProNet-E-08A/10A directly, and inquire customer service before wiring on other
products.
- 59 -
Chapter 4
Operation
4.1 Trial Operation
Make sure that all wiring has been completed prior to trial operation.
Perform the following three types of trial operation in order. Instructions are given for speed control mode (standard setting)
and position control mode. Unless otherwise specified, the standard parameters for speed control mode (factory settings)
are used.
（1）Trial Operation for Servomotor Without Load (Refer to 4.1.1)
■ Purpose
The servomotor is operated without connecting the shaft to the
machine in order to confirm the following wiring is correct.
To power supply
·Power supply circuit wiring

·Servomotor wiring
·Encoder wiring
Secure the servomotor flange to the
machine, but do not connect the motor
shaft to the load shaft.
·Rotation direction and speed of servomotor.
(Please refer to step 1-4)
（2）Trial operation for servomotor with host reference (Refer to 4.1.2)

■ Purpose
The servomotor is operated without connecting the shaft to the
machine in order to confirm the following wiring is correct.
·I/O signal wiring with host controller
·Rotation direction, speed and number of rotations of servomotor.
·Check the operation of the brake, overtravel and other protective
functions.
(3) Trial operation for servomotor and machine combined. (Refer to 4.1.3)
- 60 -
■Purpose
Perform the trial operation with the servomotor
connected to the machine. The servo drive is adjusted to match the
machine characteristics.
·Servomotor speed and machine travel distance.
·Set the necessary parameters.
- 61 -
Step Item Description Reference

Install the servomotor and servo drive according to the installation
1 Installation conditions. (Do not connect the servomotor to the machine because the -
servomotor will be operated first under the no-load condition for checking.)
Connect the power supply circuit (L1, L2 and L3), servomotor wiring (U, V,
2 Wiring W), I/O signal wiring (CN1), and encoder wiring (CN2). But during (1) Trial -
Operation for Servomotor Without Load, disconnect the CN1 connector.
Turn the power ON. Using the panel operator to make sure that the servo
Turn the power
3 drive is running normally. If using a servomotor equipped with an absolute -
ON
encoder, please perform the setup for the absolute encoder.
Execute JOG Execute JOG operation with the servomotor alone under the no-load JOG
4
operation condition. Operation
Connect input Connect the input signals (CN1) necessary for trial operation to the
5 -
signals servo drive.
Use the internal monitor function to check the input signals.

Check input
6 Turn the power ON, and check the emergency stop, brake, overtravel, and -
signals
other protective functions for the correct operation.
Input the
Host
7 Servo-ON Input the Servo-ON signal, and turn ON the servomotor.
Reference
signal
Input the reference necessary for control mode, and check the servomotor Host
8 Input reference
for correct operation. Reference
Turn the power OFF, and connect the servomotor to the machine.
Protective If using a servomotor equipped with an absolute encoder, set up the absolute
9 -
operation encoder and make the initial settings for the host controller to match the
machine’s zero position.
Using the same procedure as you did to input a reference in step 8,operate
Set necessary the servomotor via the host controller and set the parameter to make sure
10 Host
parameters. the machine’s travel direction, travel distance, and travel speed all
Reference
correspond to the reference.
Host
11 Operation The servomotor can now be operated. Adjust the servo gain if necessary.
Reference
- 62 -
4.1.1 Trial Operation for Servomotor Without Load
·Release the coupling between the servomotor and the machine, and secure only the servomotor without a load.
·To prevent accidents, initially perform the trial operation for servomotor under no-load conditions (with all couplings
and belts disconnected).
In this section, confirm the cable connections of the main circuit power supply, servomotor and encoder. Incorrect wiring is
generally the reason why servomotors fail to operate properly during the trial operation.
Confirm the wiring, and then conduct the trial operation for servomotor without load according to the following steps.
Step Description Check Method and Remarks

Secure the servomotor. Secure the servomotor flange to the machine in order
to prevent the servomotor from moving during
operation.
Do not connect the servomotor shaft to the machine.
The servomotor may tip over during rotation.
Check the power supply circuit, servomotor, and encoder With the I/O signal connector (CN1) disconnected,
2 wiring. check the power supply circuit and servomotor wiring.
Refer to 3.1 Main Circuit Wiring.
Turn ON the control power supply and main circuit power If the power is correctly supplied, the panel operator
display on the front panel of the servo drive will appear
supply.
as shown on the left. The display on the left indicates
Normal Display that forward run prohibited (P-OT) and reverse run
prohibited (N-OT).
3 If an alarm display appears, the power supply circuit,
servomotor wiring, or encoder wiring is incorrect. If an
Alternate Display
alarm is displayed, turn OFF the power, find the
Example of Alarm Display problem, and correct it.
When using a servomotor with a brake, release the brake Please refer to 4.3.4 Setting for Holding Brakes
Please refer to 4.5 Operating Using Speed Control
first before driving the servomotor.
4 with Analog Reference
When using a servomotor equipped with an absolute
encoder, the encoder setup is required before driving the
servomotor.
- 63 -

Use the panel operator to operate the servomotor with
utility function Fn002 (JOG Mode Operation)Check that
the servomotor rotates in the forward direction by pressing
the INC key, and reverse direction by pressing the DEC
key.
The operation is completed when the operation is
performed as described below and the alarm display does
5 not appear.
Complete the Fn002 (JOG Mode Operation) and turn OFF
the power.
For the operation method of the panel operator, refer to
Chapter 5 Panel Operator
The servomotor speed can be changed using the Pn305
(JOG Speed).The factory setting for JOG speed is
500rpm.
 JOG Mode Operation (Fn002)

Step Display after operation Panel operator Description
Press the MODE key to select the function

1 MODE key
mode.
Press the INC key or DEC key to select
2 INC or DEC key
Fn002.
Press the ENTER key, and the servomotor will enter
3 ENTER key
JOG operation mode.
Press the MODE key. This will turn ON the power to
4 MODE key
the servomotor.
The servomotor will run in forward direction when INC

key is pressed or in reverse direction when DEC key
5 INC or DEC key is pressed. The servomotor will operate as long as the
key is pressed.
Press the MODE key. This will turn OFF the power to
6 MODE key
the servomotor.
Press the ENTER key to return to the Fn002 display
7 ENTER key of the utility function mode. Now, the servo drive is
OFF.
Note：
The servomotor’s rotation direction depends on the setting of parameter Pn001.0 (Direction Selection).
The example above describes operation with Pn001.0 in the factory setting.
- 64 -
JOG Speed
Speed Position Torque
Pn305
Setting Range Setting Unit Factory Setting Setting Validation
0~6000 rpm 500 Immediately
Set the utility function Fn002 (JOG Mode Operation) to the reference value of servomotor speed.
The servomotor can be operated using only the panel operator without reference from the host controller.
Please note that the Forward Run Prohibited (P-OT) and Reverse Run Prohibited (N-OT) signals are invalid during JOG
mode operation.
4.1.2 Trial Operation for Servomotor without Load from Host Reference
Check that the servomotor move reference or I/O signals are correctly set from the host controller to the servo drive.
Also check the wiring and polarity between the host controller and servo drive, and the servo drive operation settings are
correct. This is the final check before connecting the servomotor to the machine.
(1)Servo ON Command from the Host
The following circuits are required: External input signal circuit or equivalent.
Speed Control
Position Control
(Standard Setting)
[Pn005=H.□□1□]
[Pn005=H.□□0□]
CN1 CN1
+24V +24V
13 13
/S-ON /S-ON
14 14
P-OT P-OT
16 16
N-OT N-OT
17 17
V-REF PULS
1 30
SIGN
32
0V
0V
- 65 -
(2)Operating Procedure in Speed Control Mode (Pn005=H.□□0□)
The following circuit is required: External input signal circuit or equivalent.
Servodrive
CN1
13
+24V
/S-ON 14
P-OT 16
N-OT 17
V-REF+ 0V
V-REF+ 1
V-REF-
V-REF- 2
GND 3
Max. Voltage (12V)

Check the power and input signal circuits again,
Refer to the above figure for the input signal circuit.
1 and check that the speed reference input (voltage
between the V-REF+ and V-REF-) is 0V.
If the servomotor rotates at an extremely slow speed, refer to
2 Turn ON the servo ON (/S-ON) input signal. 4.5.3 Adjusting Reference Offset, and use the reference
voltage offset to keep the servomotor from moving.
Generally increase the speed reference input
3 The factory setting is 6V/rated rotation speed.
voltage between V-REF+ and V-REF- from 0 V.
Check the speed reference input to the servo drive
4 Refer to 5.1.6 Operation in Monitor Mode.
(Un001[rpm])
5 Check the Un000 (motor speed [rpm]) Refer to 5.1.6 Operation in Monitor Mode.
Check that the Un001 and Un000 values in steps 4 Change the speed reference input voltage and check that
6
and 5 are equal. Un001 and Un000 are equal for multiple speed references.
Refer to the following equation to change the speed reference
input gain (Pn300).
Un001＝(V-REF Voltage)[V]×Pn300
Check the speed reference input gain and
To change the servomotor rotation direction without changing
7 servomotor rotation direction.
polarity for speed reference input voltage, refer to 4.3.2
Switching the Servomotor Rotation Direction.
Perform the operation from step 2 again after the servomotor
rotation direction is changed.
When the speed reference input is set to 0 V and
8 servo OFF status enters, trial operation for
servomotor without load is completed.
- 66 -
■ When Position Control is configured at the Host
When the servo drive conducts speed control and position control is conducted at the host controller, perform the
operation below,following the operation in Operation Procedure in Speed Control Mode (Pn005=H.□□0□).

Check the input signal circuit again, and check that
9 the speed reference input (between the V-REF+ and Refer to the above figure for input signal circuit.
V-REF-) is 0 V.
If the servomotor rotates at an extremely slow speed,
refer to 4.5.3 Adjusting Reference
10 Turn the servo ON input signal (/S-ON) ON.
Offset, and use the reference voltage offset to keep the
servomotor from moving.
Send the command for the number of servomotor Refer to 5.1.6 Operation in Monitor Mode for how it is
rotations. Check the sent number of rotations, the displayed.
11
actual number of rotations by visual inspection, and Un004(rotation angle)[pulse]: The number of pulses
the Un004 (rotation angle)[pulse] from the zero point.
If the sent number of rotations and actual number of Refer to 4.5.8 Encoder Signal Output for how to set
rotations in step 11 are not equal, correctly set the PG divided ratio (Pn200[P/Rev]):The
12
Pn200 (PG divided ratio) outputting the encoder pulse number of encoder pulses per revolution.
from the servo drive.
When the speed reference input is set to 0 V and —
13 servo OFF status is entered, the trial operation for

position control with the host controller is completed.
- 67 -
(3)Operating Procedure in Position Control Mode (Pn005=H.□□1□)

The following circuit is required: External input signal circuit or equivalent.
Servodrive
CN1
+24V
13
/S-ON
14
P-OT
16
N-OT
17
CLR
40
PULS
30
Pulse reference
/PULS 31
SIGN
Reference pulse 32
according to parameter /SIGN
Pn004.2 setting. 33

Match the reference pulse form with the pulse output form Set the reference pulse form with Pn004.2.
1
from the host controller.
Set the reference unit and electronic gear ratio so that it Set the electronic gear ratio with Pn201(or
2
coincides with the host controller setting. Pn203)/Pn202.
3 Turn the power and the servo ON input signal ON.
Send the slow speed pulse reference for the number of Set the servomotor speed to 100rpm for the
4 servomotor rotation easy to check (for example, one reference pulse speed because such speed is safe.
servomotor revolution) from the host controller in advance.
Check the number of reference pulses input to the servo Refer to 5.1.6 Operation in Monitor Mode for how
5 drive by the changed amount before and after the Un013 and it is displayed.
Un014(input reference pulse counter)[pulse] were executed.
Check whether the actual number of servomotor rotations Refer to 5.1.6 Operation in Monitor Mode for how
6 Un009、Un010 coincides with the number of input reference it is displayed.
pulses.
Check that the servomotor rotation direction is the same as Check the input pulse polarity and input reference
7
the reference. pulse form.
Input the pulse reference with the large number of Set the servomotor speed to 100rpm for the
8 servomotor rotation from the host controller to obtain the reference pulse speed because such speed is safe.
constant speed.
Check the reference pulse speed input to the servo drive Refer to 5.1.6 Operation in Monitor Mode for how
9 using the Un008 in Monitor Mode. (input reference pulse it is displayed.
speed)[rpm].
Check the servomotor speed using the Un000 in Monitor Refer to 5.1.6 Operation in Monitor Mode for how
10
Mode. (servomotor speed) [rpm]. it is displayed.
To change the servomotor rotation direction without
changing the input reference pulse form, refer to
11 Check the rotation of the servomotor shaft. 4.3.2 Switching the Servomotor Rotation
Direction. Perform the operation from step 8 again
after the servomotor rotation direction is changed.
When the pulse reference input is stopped and servo OFF —
12 status is entered, the trial operation for servomotor without
load in position control mode is complete.
- 68 -
4.1.3 Trial Operation with the Servomotor Connected to the Machine
·Follow the procedure below for trial operation precisely as given.

·Malfunctions that occur after the servomotor is connected to the machine not only damage the machine, but may
also cause an accident resulting in death or injury.
Follow the procedure below to perform the trial operation.

1 Turn the power ON, and make the settings for the Refer to 4.3 Setting Common Basic Functions.
mechanical configuration related to protective When a servomotor with brake is used, take advance
functions such as overtravel and brake. measures to prevent vibration due to gravity acting on
the machine or external forces before checking the
brake operation. Check that both servomotor and brake
operations are correct.
For details, refer to 4.3.4 Setting for Holding Brakes.
2 Set the necessary parameters for the control mode Refer to 4.5 Operating Using Speed Control with
used. Analog Reference, 4.6 Operating Using Position
Control, and 4.7 Operating Using Torque Control for
control mode used.
3 Connect the servomotor to the machine with the
coupling,etc.,while the power is OFF.
4 Check that the servo drive is servo OFF status and Refer to 4.3 Setting Common Basic Functions.
then turn ON the power to the machine (host For the following steps, take advanced measures for an
controller). Check again that the protective function in emergency stop so that the servomotor can stop safely
step 1 operates normally. when an error occurs during operation.
5 Perform trial operation with the servomotor connected Check that the trial operation is completed according to
to the machine, following each section in 4.1.2 Trial the trial operation for servomotor without load. Also,
Operation for Servomotor without Load from Host check the settings for machine such as reference unit.
Reference.
6 Check the parameter settings for control mode used in Check that the servomotor rotates matching the
step 2. machine operating specifications.
7 Adjust the servo gain and improve the servomotor The servomotor will not be broken in completely during
response characteristics, if necessary. trial operation. Therefore, let the system run for a
sufficient amount of time to ensure that it is properly
broken in.
8 Thus, the trial operation with the servomotor
connected to the machine is complete.
- 69 -
4.1.4 Trial Operation for Servomotor with Brakes
Holding brake operation of the servomotor can be controlled with the brake interlock output (/BK) signal of the servo drive.
When checking the brake operation,take advance measures to prevent vibration due to gravity acting on the machine or
external forces. Check the servomotor operation and holding brake operation with the servomotor separated from the
machine. If both operations are correct, connect the servomotor to the machine and perform trial operation.
Refer to 4.3.4 Setting for Holding Brakes for wiring on a servomotor with brakes and parameter settings.
4.1.5 Position Control by Host Controller
As described above, be sure to separate the servomotor and machine before performing trial operation of the servomotor
without a load. Refer to the following table, and check the servomotor operation and specifications in advance.
Reference from the Host

Check Item Check Method Review Items
Controller
JOG Operation Servomotor speed Check servomotor speed as Check the parameter setting at
(Constant speed reference follows: Pn300 to see if reference
input from host controller) ·Use the servomotor speed monitor speed gain is correct.
(Un000) on the panel operator.
·Run the servomotor at a low
speed.
For example, input a reference
speed of 60rpm, and check to see if
the servomotor makes one
revolution per second.
Simple positioning Number of Input a reference equivalent to one Check the parameter setting at
servomotor servomotor rotation, and visually Pn200 to see if the number of
rotation check to see if the shaft makes one PG dividing pulses is correct.
revolution.
Overtravel (P-OT and Whether the Check to see if the servomotor Review P-OT and N-OT wiring
N-OT Used) servomotor stops stops when P-OT and N-OT signals if the servomotor does not
rotating when are input during continuous stop.
P-OT and servomotor operation.
N-OT signals
are input.
4.2 Control Mode Selection
The control modes supported by the ProNet series servo drives are described below.
- 70 -
Parameter Control Mode Reference Section

Speed Control (Analog voltage reference)
Controls servomotor speed using analog voltage speed reference.
Use in the following instances.
H.□□0□ 4.5
·To control speed
·For position control using the encoder feedback division output from
the servo drive to form a position loop in the host controller.
Position Control (Pulse train reference)
Controls the position of the servomotor using pulse train position
reference.
H.□□1□ 4.6
Controls the position with the number of input pulses, and controls the
speed with the input pulse frequency.
Use when positioning is required.
Torque Control (Analog voltage reference)
Pn005 Controls the servomotor’s output torque with analog voltage torque
H.□□2□ 4.7
reference. Use to output the required amount of torque for operations
such as pressing.
Speed Control (contact reference) Speed Control
(zero reference)
Use the three input signals /P-CON，/P-CL and /N-CL to control the
H.□□3□ 4.8
speed as set in advance in the servo drive.
Three operating speeds can be set in the servo drive. (In this case, an
analog reference is not necessary.)
H.□□4□ These are swiching modes for using the four control methods
· described above in combination. Select the control method switching
· mode that best suits the application. 4.10
·
H.□□E□
- 71 -
4.3 Setting Common Basic Functions
4.3.1 Setting the Servo ON Signal
This sets the servo ON signal (/S-ON) that determines whether the servomotor power is ON or OFF.
(1)Servo ON signal(/S-ON)
Connector Pin
Type Name Setting Meaning
Number
ON(low level) Servomotor power ON. Servomotor can be operated.
CN1-14
Input /S-ON Servomotor power OFF. Servomotor cannot be
(Factory setting) OFF(high level)
operated.
■Important
Always input the servo ON signal before inputting the input reference to start or stop the servomotor.
Do not input the input reference first and then use the /S-ON signal to start or stop. Doing so will degrade internal
elements and may cause the servo drive to malfunction.
A parameter can be used to re-allocate the input connector number for the /S-ON signal. Refer to 3.2.2 I/O Signal Names
and Functions.
(2) Enabling/Disabling the Servo ON Signal

A parameter can be always used to set the servo ON condition. This eliminates the need to wire /S-ON, but care must be
taken because the servo drive can operate as soon as the power is turned ON.
Parameter Meaning
b.□□□0 External S-ON signal enabled (Factory setting)
Pn000 External S-ON signal disabled, the servomotor excitation signal is
b.□□□1
opened automatically after outputting the S-RDY signal.
After changing these parameters, turn OFF the main circuit and control power supplies, and then turn them
ON again to enable the new settings.
- 72 -
4.3.2 Switching the Servomotor Rotation Direction
The rotation direction of the servomotor can be switched without changing the reference pulse to the servo drive or the
reference voltage polarity.
This causes the rotation the servo motor shaft is rotating to change. The output signal polarity, such as the encoder pulse
output and the analog monitor signal from the servo drive do not change.
The standard setting for “forward rotation” is counterclockwise as viewed from the servomotor load end.
Reference
Parameter Name
Forward reference Reverse reference
b.□□□0 Standard setting
(CCW=forward) CCW
(factory setting) Encoder pulse division output CW Encoder pulse divisionoutput
PAO
PAO
PBO PBO
Pn001
b.□□□1 Reverse rotation
mode CCW
CW
(CW=forward) Encoder pulse divisionoutput
Encoder pulse division output
PAO
PAO
PBO
PBO
The direction of P-OT and N-OT change. For Pn001=b.□□□0(standard setting), counterclockwise is P-OT. For
Pn001=b.□□□1(reverse rotation mode), clockwise is P-OT.
- 73 -
4.3.3 Setting the Overtravel Limit Function
The overtravel limit function forces movable machine parts to stop if they exceed the allowable range of motion and turn
ON a limit switch.
(1)Connecting the overtravel signal
To use the overtravel function, connect the following overtravel limit switch to the corresponding pin number of servo drive
CN1 connector correctly.
Type Signal Name Pin No. Setting Meaning

Forward rotation allowed. (Normal
ON(low level)
CN1-16 operation status.)
Input P-OT
(factory setting) Forward rotation prohibited.
OFF(high level)
(Forward overtravel)
Reverse rotation (Normal operation
ON(low level)
CN1-17 status.)
Input N-OT
(factory setting) Reverse rotation prohibited.
OFF(high level)
(Reverse overtravel)
Connect limit switches as shown below to prevent damage
to the devices during linear motion. Servomotor forward rotation direction.
Rotation in the opposite direction is possible during Servodrive
overtravel. Servomotor
CN1
For example, reverse rotation is possible during forward Limit switch Limit switch
P-OT
16
overtravel. N-OT 17
■Important
When using overtravel to stop the servomotor during position control, the position error pulses are present. A clear signal
(CLR) input is required to clear the error pulses.
When using the servomotor on a vertical axis, the workpiece may fall in the overtravel condition.
To prevent this, always set the zero clamp after stopping with Pn004.0=5.
- 74 -
(2)Enabling/Disabling the Overtravel Signal

A parameter can be set to disable the overtravel signal. If the parameter is set, there is no need to wire the overtravel input
signal.
Parameter Meaning
b.□□0□ Inputs the forward rotation prohibited (P-OT) signal from
CN1-16 (factory setting).
b.□□1□ Disables the forward rotation prohibited (P-OT) signal. (Allows constant
forward rotation.)
Pn000
b.□0□□ Inputs the reverse rotation prohibited (N-OT) signal from CN1-17.
(factory setting)
b.□1□□ Disables the reverse rotation prohibited (N-OT) signal. (Allows constant
reverse rotation.)
·Applicable control modes: Speed control, position control, and torque control.
·After changing these parameters, turn OFF the main circuit and control power supplies, and then turn them ON again to
enable the new settings.
·A parameter can be used to re-allocate input connector number for the P-OT and N-OT signals. Refer to 3.2.2 I/O Signal
Names and Functions.
（3）Selecting the Servomotor Stop Method

This is used to set the stop method when an overtravel(P-OT,N-OT)signal is input while the servomotor is operating.
Mode After
Parameter Stop Mode Meaning
Stopping
Stop by dynamic Rapidlly stops the servo motor by dynamic braking(DB),
H.□□□0
brake then places it into coast (power OFF) mode.
Coast Stops the servo motor in the same way as when the
H.□□□1 Coast to a stop servo is OFF (coast to a stop ), then places it into
coast(power OFF) mode.
Stops the servomotor by dynamic braking (DB) when
H.□□□2 servo OFF, stops the servo motor by plug braking when
overtravel, and then places it into coast (power OFF)
mode.
Coast
Pn004 Makes the servomotor coast to a stop state when servo
OFF, stops the servomotor by plug braking when
H.□□□3
S-OFF overtravel, and then places it into coast (power OFF)
/Overtravel mode.
Stops the servomotor by dynamic braking (DB) when
H.□□□4
servo OFF, stops the servomotor by plug braking when
overtravel, and then places it into zero clamp mode.
Zero Clamp
Makes the servomotor coast to a stop state when servo
H.□□□5 OFF, stops the servomotor by plug braking when
overtravel, then places it into zero clamp mode.
- 75 -
·After changing these parameters, turn OFF the main circuit and control power
supplies, and then turn them ON again to enable the new settings.
·Stop by dynamic brake: Stops by using the dynamic brake (short circuiting its
electrical circuit).
·Coast to a stop: Stops naturally, with no brake, by using the friction resistance
of the servomotor in operation.
·Plug braking: Stops by using plug braking limit torque.
·Zero Clamp Mode: A mode forms a position loop by using the position
reference zero.
·Dynamic brake is an emergency stop function, and one of the general methods to cause a servomotor sudden stop.
·Dynamic brake suddenly stops a servomotor by shorting its electrical circuit.
·If the servomotor is frequently started and stopped by turning the power ON/OFF or using the servo ON signal(/S-ON),
the DB circuit will also be repeatedly operated, degrading the servo drive’s internal elements.
·Use the speed input reference and position reference to control the starting and the stopping of the servomotor.
(4)Setting the Stop Torque for Overtravel

Plug braking torque limit`
Pn405
0～300 1% 300 Immediately
· This sets the stop torque for when the overtravel signal (P-OT,N-OT) is input.
· The setting unit is a percentage of the rated torque. (the rated torque is 100%)
· The value large enough to be the servomotor maximum torque, 300% is set as the factory setting for plug braking limit
torque. However, the actual output plug braking limit torque is determined by servomotor ratings.
- 76 -
4.3.4 Setting for Holding Brakes
The holding brake is used when the servo drive controls a vertical axis.
A servomotor with the brake option helps prevent movable parts from shifting due to gravity when power is removed from
the servo drive.
(Refer to 4.1.4 Trial Operation for Servomotor with Brakes.)
1. The servomotor with the built in brake, is a de-energization brake. It is used to hold the servomotor and cannot be used
as a braking purposes. Use the holding brake only to hold a stopped servomotor.
2. When operating using only a speed loop, turn OFF the servo and set the input reference to 0V when the brake is
applied.
3. When forming a position loop, do not use a mechanical brake while the servomotor is stopped because the servomotor
enters servolock status.
（1）Wiring Example
Use the servo drive sequence output signal /BK and the brake power supply to form a brake ON/OFF circuit.
The following diagram shows a standard wiring example.
Servodrive Servomotor with brake
Power supply
R L1 U
S L2 V
M
T L3 W
L1C
L2C
CN2 PG
CN1
BK-RY (/BK+) *1
+24V
(/BK-) *2
BK
Brake power supply
BK-RY Yellow or blue Red

White AC DC Black
BK-RY：Brake control relay
1*、2*：The output terminals allocated with Pn511.
- 77 -
（2）Brake interlock output

Type Signal Name Connector Pin Number Setting Meaning
ON(Low level) Releases the brake.
Output /BK Must be allocated
OFF(High level) Applies the brake.
This output signal controls the brake and is used only for a servomotor with a brake. This output signal is not used with
the factory setting.The output signal must be allocated by Pn511. It does not need to be connected for servomotor
without a brake.
（3）Allocating Brake Interlock Output (/Bk)
Brake interlock output (/BK) is not used with the factory setting.The output signal must be allocated.
Connector Pin Number
Parameter Meaning
+ Terminal - Terminal
The /BK signal is output from output
Pn511 H.□□□4 CN1-11 CN1-12
terminal CN1-11,12.
Pn511 H.□□4□ CN1-5 CN1-6
terminal CN1-5,6.
Pn511 H.□4□□ CN1-9 CN1-10
terminal CN1-9,10.
■Important
When set to the factory setting, the brake signal is invalid.
For the allocation of servo drive output signals other than /BK signal, refer to 3.2.2 I/O Signal Names and Functions.
Parameter Pn511 description as following：
0 /COIN(/V-CMP)output
1 /TGON rotation detecting output
2 /S-RDY servo drive get ready output
3 /CLT torque limit output
4 /BK brake interlock output
5 /PGC encoder C pulse output
6 OT overtravel signal output
7 /RD servo enabled motor excitation output
8 /HOME home completion output
9 /TCR Torque Detection Output
Related parameter：
Parameter Setting
Name Unit Default
No. Range
Pn505 Servo ON waiting time ms -2000~2000 0
Pn506 Basic waiting flow 10ms 0~500 0
Pn507 Brake waiting speed rpm 10～100 100
Pn508 Brake waiting time 10ms 10～100 50
- 78 -
（4）Setting the Brake ON/OFF Timing after the Servomotor Stops

With the factory setting, the /BK signal is output at the same time as the servo is turned OFF. The servo OFF timing can be
changed with a parameter.
Servo ON waiting time
Pn505
-2000～2000 ms 0 Immediately
Basic waiting flow
Pn506
0～500 10ms 0 Immediately

·When using the servomotor to control a vertical axis, the machine movable parts may shift slightly depending on the
brake ON/ OFF timing due to gravity or an external force. By using this parameter to delay turning the servo ON/ OFF, this
slight shift can be eliminated.
·For details on brake operation while the servomotor is operating, refer to (5) Setting the Brake ON/ OFF Timing When
Servomotor Running in this section.
/S-ON (CN1-14) Servo ON Servo OFF Servo ON
Brake released Using brakes Brake released

/BK Output
brake
Power to Power to
Power to Servomotor No power to
servomotor servomotor
servomotor
Pn506 Pn505
■Important
·The servomotor will turn OFF immediately when an alarm occurs, regardless of the setting of this parameter.
·The machine movable part may shift due to gravity or external force during the time until the brake operates.
- 79 -
（5）Setting the Brake ON/OFF Timing When Servomotor Running
The following parameters can be used to change the /BK signal output conditions when a stop reference is output during
servomotor operation due to the servo OFF or an alarm occuring.
Brake Waiting Speed

Pn507
10～100 1rpm 100 Immediately
Brake Waiting Time

Pn508
/BK Signal Output Conditions When Servomotor Running
The /BK signal goes to high level (brake ON) when either of the following conditions is satisfied:
· When the servomotor speed falls below the level set in Pn507 after servo OFF.
· When the time set in Pn508 is exceeded after servo OFF.
Servo OFF
/S-ON input Servo ON
or alarm or
power OFF
Servomotor stopped
by applying DB or
Servomotor Speed Pn507 coasting.
(Pn004.0)
Brake released Brake held

/BK Output
Pn508
4.3.5 Instantaneous Power Loss Settings
Determines whether to continue operation or turn the servo OFF when the power supply voltage to the servo drive main
circuit is instantaneously interrupted.
Parameter Signal Name and Meaning
b.0□□□ Continue operation when the power supply voltage to servo drive main circuit is
Pn000 instantaneously interrupted.
b.1□□□ An alarm occurs when the power supply voltage to servo drive main circuit is
instantaneously interrupted.
- 80 -
4.4 Absolute Encoders
Absolute Encoder Output Range of

Resolution Action when limit is exceeded
Type Multiturn Data
·When the upper limit (+32767)is exceeded in the
forward direction, the multiturn data is -32768
16-bit/multiturn
ProNet Series -32768～+32767 ·When the lower limit (-32768)is exceeded
17-bit/singleturn
in the reverse direction, the multiturn data is
+32767.
The absolute position can be read by the MODBUS protocol. In the actual control, the MODBUS protocol can read the
initial position when the servomotor is stopped (S-OFF), then the real-time position during the servomotor is running can
be found from the number of PG divided output pulses.
4.4.1 Selecting an Absolute Encoder
An absolute encoder can also be used as an incremental encoder.
Parameter Meaning
Pn002 b.□0□□ Use the absolute encoder as an absolute encoder. (Factory setting)
b.□1□□ Use the absolute encoder as an incremental encoder.
·The back-up battery is not required when using the absolute encoder as an incremental encoder.
·After changing these parameters, turn OFF the main circuit and control power supplies and then turn them ON
again to enable the new settings.
- 81 -
4.4.2 Handling Battery
In order for the absolute encoder to retain position data when the power is turned OFF, the data must be backed up by a
battery.
Please purchase the special cable and battery case mabe by Estun if an absolute encoder is used.
Install the battary to the encoder cable：
A. Open the shell of the battery case.
B. Install the battery according to the following diagram.
C. Cover the shell of the battery case.
- 82 -
4.4.3 Replacing Battery
The servo drive will generate an absolute encoder battery alarm (A.48) when the battery voltage drops below about 3.1V.
 Battery Replacement Procedure
1. Replace the battery with only the servo drive control power supply turned ON.
2. After replacing the battery, using the panel operator with utility function Fn011 to cancel the absolute encoder battery
alarm (A.48).
3. Turn ON the servo drive power back again. If it operates without any problems, the battery replacement has been
completed.
Note:
·The servo drive will generate an absolute encoder battery alarm (A.48) when the battery voltage drops below about 3.1V.
·If an absolute encoder battery alarm (A.47) occurred, it means the battery voltage drops below about 2.5V, and the
multiturn data is lost. Please reset the absolute encoder after changing the battery.
4.4.4 Absolute Encoder Setup(Fn010、Fn011)
Setting up the absolute encoder in the following cases.
·When starting the machine for the first time,set Pn002.2 to 0.
·When an encoder error alarm (A.45～A.48, A.51) is generated.
Use the panel operator in the servo drive for setup.
Note:
1. Encoder setup operation is only possible when the servo is OFF.
2. If the absolute encoder alarms(A.45～A.48，A.51 ) are displayed, cancel the alarm by using the same method as the
setup. They cannot be cancelled with the servo drive alarm reset input signal(/ALM-RST).
3. Any other alarms that monitor the inside of the encoder should be cancelled by turning OFF the power.
- 83 -
4.5 Operating Using Speed Control with Analog Reference
4.5.1 Setting Parameters
Parameter Meaning
Pn005 H.□□0□ Control mode selection:Speed control(analog reference)(factory setting)
Speed Reference Input Gain

Pn300
0～3000 rpm/v 150 Immediately
Sets the analog voltage level for the speed reference (V-REF) necessary to operate the servomotor at the rated speed.
■EXAMPLE
Pn300=150：1V input is equivalent to the servomotor speed of 150rpm (factory setting).
- 84 -
4.5.2 Setting Input Signals
（1）Speed Reference Input

Input the speed reference to the servo drive using the analog voltage reference to control the servomotor speed in
proportion to the input voltage.
Type Signal Name Connector Pin Number Name
V-Ref+ CN1-1 Speed Reference Input
Input
V-Ref- CN1-2 Speed Reference Input
The above inputs are used for speed control(analog voltage reference). (Pn005.1=0，4，7，9，A) Pn300 is used to set the
speed reference input gain.Refer to 4.5.1 Setting Parameters.
（2）Proportional Control Reference (/P-CON)

Connector Pin
Tpye Signal Setting Meaning
Number
Operates the servo drive with proportional
ON(low level)
control
Input /P-CON CN1-15
Operates the servo drive with proportional
OFF(high level)
integral control.
/P-CON signal selects either the PI(proportional integral) or P(proportional) Speed Control Mode.
Switching to P control reduces servomotor rotation and minute vibrations due to speed reference input drift.
Input reference: At 0V, the servomotor rotation due to drift will be reduced, but servomotor rigidity (holding force) drops when
the servomotor is stopped.
Note: A parameter can be used to reallocate the input connector number for the /P-CON signal. Refer to 3.2.2 I/O Signal
Names and Functions.
- 85 -
4.5.3 Adjusting Reference Offset
When using the speed control, the servomotor may rotate slowly even if 0V is specified as the analog voltage reference.
This happens if the host controller or external circuit has a slight offset (in the unit of mV) in the reference voltage.
Adjustments can be done manually or automatically by using the panel operator. Refer to 5.2 Operation in Utility
Function Mode.
The servo drive automatically adjusts the offset when the host controller or external circuit has the offset in the reference
voltage.
After completion of the automatic adjustment, the amount of offset is stored in the servo drive. The amount of offset can be
checked in the speed reference offset manual adjustment mode (Fn004). Refer to 4.5.3 (2) Manual Adjustment of the
Speed Reference Offset.
(1) Automatic Adjustment of the Speed Reference Offset

The automatic adjustment of reference offset (Fn003) cannot be used when a position loop has been formed with a host
controller and the error pulse is changed to zero at the servomotor stop due to servolock. Use the speed reference offset
manual adjustment (Fn004) described in the next section for a position loop.
The zero-clamp speed control function can be used to force the servomotor to stop while the zero speed reference is
given. Refer to 4.5.7 Using the Zero Clamp Function.
Note:The speed reference offset must be automatically adjusted with the servo OFF.
Adjust the speed reference offset automatically in the following procedure.
1.Turn OFF the servo drive and input the 0V reference voltage from the host controller or external circuit.
2.Press the MODE key to select the utility function mode.

3.Press the INC or DEC key to select parameter Fn003.
- 86 -
4.Press the ENTER key to enter into the speed reference offset automatic adjustment mode.
5.Press the MODE key for more than one second, the reference offset will be automatically adjusted.
7.Press ENTER key to return to the Fn003 display of the utility function mode.
8.Thus, the speed reference offset automatic adjustment is completed.
- 87 -
（2）Manual Adjustment of the Speed Reference Offset
Use the speed reference offset manual adjustment (Fn004) in the following situations:
·If a loop is formed with the host controller and the postion error pulse is set to be zero when servolock is stopped.
·To deliberately set the offset to some value
·To check the offset data set in the speed reference offset automatic adjustment mode.
This function operates in the same way as the reference offset automatic adjustment mode (Fn003), except that the
amount of offset is directly input during the adjustment.
The offset setting range and setting unit are as follows:
Adjust the speed reference offset manually in the following procedure.
1. Press the MODE key to select the utility function mode.

2. Press the INC or DEC key to select parameter Fn004.
3. Press the ENTER key to enter into the speed reference offset manual adjustment mode.
4. Turn ON the servo ON (/S-ON) signal. The display will be shown as below.
5. Press the ENTER key for one second to display the speed reference offset amount.
6. Press the INC or DEC key to adjust the amount of offset.

7. Press the ENTER key for one second to return to the display in step 4.
8. Press the ENTER key to return to the Fn004 display of the utility function mode.
9. Thus, the speed reference offset manual adjustment is completed.
- 88 -
4.5.4 Soft Start
The soft start function converts the stepwise speed reference inside the servo drive to a consistent rate of acceleration
and deceleration.
Pn310 can be used to select the soft start form:
0: Slope; 1: S curve; 2: 1st-order filter; 3: 2nd-order filter
Soft Start Acceleration Time
Speed
Pn306
Soft Start Deceleration Time
Speed
Pn307
The soft start function enables smooth speed control when inputting a stepwise speed reference or when selecting
internally set speeds. Set both Pn306 and Pn307 to “0” for normal speed control.
Set these parameters as follows:
· Pn306：The time interval from the time the servomotor starts until the servomotor maximum speed is reached.
· Pn307：The time interval from the time the servomotor is operating at the servomotor maximum speed until it stops.
4.5.5 Speed Reference Filter Time Constant
Speed Reference Filter Time Constant

Speed
Pn308
st
This smooths the speed reference by applying a 1 –order delay filter to the analog speed reference (V-REF) input. A
value that is too large, however, will decrease response.
- 89 -
4.5.6 S-curve Risetime
S-curve Risetime
Speed
Pn309
4.5.7 Using the Zero Clamp Function
（1）Zero Clamp Function
The zero clamp function is used for systems where the host controller does not form a position loop for the speed
reference input. When the zero clamp signal（/P-CON）is ON, a position loop is formed inside the servo drive as soon as
the input voltage of the speed reference (V-REF) drops below the servomotor zero clamp speed. The servomotor ignores
the speed reference and quickly stops and locks the servomotor.
The servomotor is clamped within ±1 pulse when the zero clamp function is turned ON, and will still return to the zero
clamp position even if it is forcibly rotated by an external force.
- 90 -
（2）Parameter Setting
Parameter Meaning
Pn005 H.□□A□ Control mode: Speed control(analog voltage reference) Zero Clamp
Zero Clamp Conditions:
Zero clamp is performed with Pn005=H.□□A□ when the following two conditions are both satisfied:
·/P-CON is ON (low level)
·Speed reference (V-REF) drops below the setting in Pn502.
Servodrive Speed “V-REF”speed reference
CN1 Preset value for zero

V-REF clamping Pn502
Speed reference 1
Time
/P-CON Open（OFF) Closed（ON)
Zero clamp 15 “/P-CON”input
Zero clamp is performed. OFF OFF

ON
ON ON
Zero clamp speed

Speed
Pn502
0～3000 rpm 10 Immediately
Sets the servomotor speed at which the zero clamp is performed if zero clamp speed control(Pn005=H.□□A□) is
selected. Even if this value is set higher than the maximum speed of the servomotor, the maximum speed will be used.
（3）Input Signal Setting

Zero clamp function
ON(low level)
ON(enabled)
/P-CON CN1-15
Zero clamp function
OFF(high level)
OFF(disabled)
Input Not including this setting in Zero clamp function
ON(low level)
the default setting,please ON(enabled)
/ZCLAMP choose terminal output by
setting parameter Zero clamp function
OFF(high level)
Pn509,Pn510 OFF(disabled)
/P-CON and /ZCLAMP are the input signals to switch to the zero clamp function.
■Important
In speed control (analog voltage reference) mode,when /ZCLAMP is allocated to an output terminal,zero clamp
function is enabled.
- 91 -
4.5.8 Encoder Signal Output
Encoder feedback pulses processed inside the servo drive can be output externally.
PAO CN1-20 Encoder output phase A
Output
/PAO CN1-21 Encoder output phase /A
PBO CN1-22 Encoder output phase B
Output
/PBO CN1-23 Encoder output phase /B
PCO CN1-24 Encoder output phase C(zero-point pulse)
Output
/PCO CN1-25 Encoder output phase /C(zero-point pulse)
These outputs explained here.
Servodrive Host Controller
Encoder CN1
*
CN2 Phase A(PAO)
Serial Data Frequency Phase B(PBO)
PG
dividing
Phase C(PCO)
circuit
* The dividing output phase form is the same as the standard setting (Pn001.0=0) even if in reverse rotation mode
(Pn001.0=1).
■Output phase form
If the servomotor is not equipped with an absolute encoder, the servomotor needs two full rotations before using the servo
drive's Phase-C pulse output as the zero point reference.
Dividing: Dividing means that the divider converts data into the pulse density (Pn200) based on the pulse data of the
encoder installed on the servomotor, and outputs it. The setting unit is number of pulses/revolution.
- 92 -
 Pulse Dividing Ratio Setting

PG Dividing Ratio
Pn200
16~16384 1Puls 16384 After restart
Set the number of pulses for PG output signals (PAO,/PAO,PBO,/PBO) externally from the servo drive.
Feedback pulses from the encoder per revolution are divided inside the servo drive by the number set in Pn200 before
being output. (Set according to the system specifications of the machine or host controller.)
The setting range varies with the number of encoder pulses for the servomotor used.
■Output Example
Pn200=16(when 16 pulses are output per revolution)
4.5.9 Speed coincidence output
The speed coincidence (/V-CMP) output signal is output when the actual servomotor speed during speed control is the
same as the speed reference input. The host controller uses the signal as an interlock.
CN1-11，12 ON(low level) Speed coincides.
Output /V-CMP(/COIN)
(factory setting) OFF(high level) Speed does not coincide.
Coincidence Difference
Speed
Pn501
The /V-CMP signal is output when the difference between the speed reference and actual servomotor speed is less than
Pn501.
■Example
The /V-CMP signal turns ON at 1900 to 2100rpm if the Pn501 parameter is set to 100 and the reference speed is
2000rpm.
■Note
This pin outputs the /COIN signal in position control mode, and the /V-CMP signal in speed control mode.
- 93 -
4.6 Operating Using Position Control
Set the following parameters for position control using pulse trains.
Parameter Meaning
Pn005 H.□□1□ Control mode selection：position control (pulse train reference)
A block diagram for position control is shown as below.

Servodrive(in position control)
Pn113
Pn112 Pn201
Pn111
Feed forward
Feed forward B filter time
Differential Offset
A constant
Pn500
Pn202
Positioning
complete
Pn004.2
Pn201 Pn104 Servomotor
Pn204
×1 + +
Reference pulse B + +
×2 Smoothing KP Speed loop Current loop M
A Error counter
×4
Pn202 -
×4
PG
Pn200
PG signal output
dividing Encoder
4.6.1 Basic Setting in Position Control
(1)Setting a reference pulse sign

PULS CN1-30 Reference pulse input
/PULS CN1-31 Reference pulse input
Input
SIGN CN1-32 Reference sign input
/SIGN CN1-33 Reference sign input
(2)Setting reference input filter for open collector signal
Pn006 0□□□ when pulse is difference input, servo receiving pulse frequency ≤4M
1□□□ when pulse is difference input, servo receiving pulse frequency ≤650K
2□□□ when pulse is difference input, servo receiving pulse frequency ≤150K
- 94 -
(3) Setting a Reference Pulse Form

Set the input form for the servo drive using parameter Pn004.2 according to the host controller specifications.
Reference Input Pulse Forward Rotation Reverse Rotation
Parameter
Pulse Form Multiplier Reference Reverse
Sign+pulse train PULS PULS
(CN1-30) (CN1-30)
H.□0□□ (positive logic) — SIGN SIGN

H L
(CN1-32) (CN1-32)
(factory setting)
PULS
(CN1-30)
L PULS
CW+CCW SIGN
(CN1-30)
H.□1□□ — (CN1-32)
Pn004 (positive logic)
SIGN
(CN1-32) L
H.□2□□ Two-phase pulse ×1

H.□3□□ train with 90° ×2
phase differential
H.□4□□ ×4
(positive logic)
■Note:
The input pulse multiplier can be set for the two-phase pulse train with 90° phase differential reference pulse form.
Forward Rotation Reverse Rotation
PULS
(CN1-30)
SIGN
(CN1-32)
×1倍
Internal processing ×2倍 Servomotor movement

reference pulses.
×4倍
(4)Inverse PULS and SIGN reference

Pn004 0□□□ Do not inverse PULS reference and SIGN reference
1□□□ Do not inverse PULS reference; Inverse SIGN reference
2□□□ Inverse PULS reference; Do not inverse SIGN reference
3□□□ Inverse PULS reference and SIGN reference
- 95 -
(5)Reference Pulse Input Signal Timing

Reference pulse signal form Electrical specifications Remarks
Sign+pulse train input SIGN
(SIGN+PULS signal) SIGN t1
H=forward reference
t2
t7
Maximum reference frequency： L=reverse reference

t3
PULS t1，t2=0.1µs
t4 t5 t6
t3，t7=0.1µs
t
t4，t5，t6>3µs
500kpps (For open-collector output： T t =1.0µs
(t /T)×100 = 50%
200kpps)
CW pulse+CCW pulse Maximum t1
reference frequency:500kpps CCW

t2 t t1，t2=0.1µs
t3>3µs
(For open-collector output：200kpps) CW t =1.0µs
(t /T)×100 = 50%
t3
Two-phase pulse train with 90° phase A parameter

differential (phase A +B) t1 t2
Pn004.2 can be
Phase A
t1，t2=0.1µs
Maximum reference frequency： Phase B t =1.0µs used to switch of
t (t /T)×100 = 50%
T
×1 input pulse multiplier：500kpps the input pulse
×2 input pulse multiplier：400kpps Phase B leads A by 90º. Phase B lags B by 90º. multiplier mode.
×4 input pulse multiplier：
200kpps
(6)Connection Example
The pulse train output form from the host controller corresponds to the following:
• Line-driver Output
• +24V Open-collector output
• +12V/+5V Open-collector output
(a)Connection Example for Line-driver Output
Applicable line driver: SN75174 manufactured by TI or MC3487 or the equivalent.
Host controller Servodrive
Line-driver CN1
* Photocoupler
PULS 30 150Ω
/PULS 31
SIGN 32 150Ω
/SIGN 33
*
Represents twisted-pair wires。
- 96 -
(b)Connection Example for Open-Collector Gate Output

 NPN OC GATE OUTPUT
Servodrive
Host controller
1CN-30 75Ω
PULS
R
NOTE:
75Ω VDC=12~24V
/PULS 1CN-31
R=(VDC-1.5Volt)/10mA-150
VDC VDC=12V,
1CN-34 2KΩ
R=1KΩ/0.25W
2KΩ
1CN-32
VDC=24V,
SIGN
75Ω R=2KΩ/0.25W
/SIGN 1CN-33
R 75Ω
GND
 PNP OC GATE OUTPUT
Servodrive
Host controller
1CN-30 75Ω
PULS
75Ω
NOTE:
/PULS 1CN-31
VDC=12~24V
R R=(VDC-1.5Volt)/10mA-150
VDC
1CN-34 2KΩ
VDC=12V,
2KΩ R=1KΩ/0.25W
SIGN 1CN-32
75Ω
VDC=24V,
R=2KΩ/0.25W
/SIGN 1CN-33
75Ω
R
GND
Note：When the host controller is applied by open-collector signal output, the input signal noise margin lowers. When a
position error caused by the noise occurs, set the parameter Pn006.3.
- 97 -
4.6.2 Setting the Clear Signal
（1）Setting the Clear Signal
Type Sign Name Connector Pin Numbe Function
Input /CLR 1CN-40 error counter clear

When the /CLR signal is set to low level, clear error counter:
·The error counter inside the servo drive is set to “0”
·Position loop operation is disabled.
（2）Setting the Clear Signal Mode

In position control mode, pulses will be still presented in the servo drive when servo OFF, thus it should be cleared when
servo drive is turned ON. Setting Pn004 to choose whether clearing the pulses automatically when servo OFF.
□□0□ Clear the error pulse when S-OFF, do not when overtravel.
Pn004 □□1□ Do not clear the error pulse.
□□2□ Clear the error pulse when S-OFF or overtravel (excep for zero clamp)
4.6.3 Setting the Electronic Gear
（1）Electronic Gear
The electronic gear enables the workpiece travel distance per input reference pulse from the host controller to be set to
any value.
One reference pulse from the host controller, i.e., the minimum position data unit, is called a reference unit.
When the Electronic Gear is Not Used When the Electronic Gear is Used
workpiece workpiece
Reference unit：1µm
No. of encoder No. of encoder

Ball screw pitch：6mm Ball screw pitch：6mm
pulses：32768 pulses：32768
To move a workpiece 10mm using
To move a workpiece 10mm :
reference units:
One revolution is 6mm. Therefore 10÷6＝
The reference unit is 1µm. Therefore, to
1.6666 revolutions.
move the workpiece 10mm (10000µm),
32768×4 pulses is one revolution.
1pulse=1µm, so 10000/1＝10000 pulses.
Therefore, 1.6666×32768×4＝218445
Input 10000 pulses per 10mm of
pulses. 218445 pulses are input as
workpiece movement.
reference pulses.
The equation must be calculated at the
host controller.
- 98 -
（2）Related Parameters
Electronic Gear Ratio (Numerator)
Position
Pn201
1～65535 — 1 After restart
Electronic Gear Ratio (Denominator)
Position
Pn202
1～65535 — 1 After restart
The deceleration ratio of the servomotor and the load shaft is given as n/m where m is the
rotation of the servomotor and n is the rotation of the load shaft.
Electronic gear ratio: B Pn 201


A Pn 202
No. of encoder pulses  4 m
 
Travel dis tan ce per load n
shaft revolution(reference units)
·If the ratio is outside the setting range, reduce the fraction (both numerator and denominator) until you obtain integers
within the range.
·Be careful not to change the electronic gear ratio (B/A).
■Important
·Electronic gear ratio setting range: 0.01≤electronic gear ratio(B/A)≤ 100
·If the electronic gear ratio is outside this range, the servo drive will not operate properly. In this case, modify the load
configuration or reference unit.
(3)Procedure for Setting the Electronic Gear Ratio
Use the following procedure to set the electronic gear ratio.

Step Operation Description
Check the deceleration ratio, ball screw pitch and pulley
1 Check machine specifications.
diameter.
Check the number of encoder
2 Check the number of encoder pulses for the servomotor used.
pulses.
Determine the reference unit from the host controller,
3 Determine the reference unit used. considering the machine specifications and positioning
accuracy.
Calculate the travel distance per load shaft Calculate the number of reference units necessary to turn the load shaft
4
revolution. one revolution based on the previously determined reference units.s
5 Calculate the electronic gear ratio. Use the electronic gear ratio equation to calculate the ratio (B/A).
6 Set parameters. Set parameters using the calculated values.
- 99 -
(4)Electronic Gear Ratio Setting Examples
The following examples show electronic gear ratio settings for different load configurations.
Load Configuration
Ball Screw Disc Table Belt and Pulley
Reference unit：0.01mm
Reference unit：0.001mm
Load shaft Load shaft
Step Operation
Deceleration ratio: Pulley diameter:
17-bit encoder Ball screw pitch：6mm F 100mm
2：1
17-bit encoder
Pulley diameter:100 mm
Check machine Ball screw pitch:mm Rotation angle per revolution
1 (pulley circumference:314 mm)
specifications. Deceleration ratio:1/1 :360° Deceleration ratio:3/1
·Deceleration ratio:2/1
2 Encoder 17-bit:32768P/R 17-bit:32768P/R 17-bit:32768P/R
Determine the
1 reference unit:
3 reference unit 1 reference unit:0.1° 1 reference unit:0.01mm
0.001mm(1μm)
used
Calculate the
travel distance
4 6mm/0.001mm=6000 360°/0.1°=3600 314mm/0.01mm=31400
per load shaft
revolution
Calculate the
B 32768  4 1 B 32768  4 3 B 32768  4 2
5 electronic gear      
A 6000 1 A 3600 1 A 31400 1
ratio
Pn201 131072 Pn201 393216 Pn201 262144
6 Set parameters
Pn202 6000 Pn202 3600 Pn202 31400
Pn201 32768 Pn201 32768 Pn201 32768
7 Final Result
Pn202 1500 Pn202 300 Pn202 3925
·Reduce the fraction (both numerator and denominator) if the calculated result will not be within the setting range.
·For example, reduce the above numerators and denominators by four or other numbers to obtain the final results in step
7 and complete the settings.
(5)Electronic Gear Ratio Equation
Servomotor n
Pitch＝P（mm/rev）
Reference pulse B +
Position Speed
A — loop loop m
(mm / P )
(mm / P ) : Reference unit ×4
PG(P/rev))
PG(P/rev))：Encoder pulses
P（mm/rev）：Ball screw pitch
m
：Deceleration ratio
n
n p B
 ( )  4  PG  m
 A
B 4  PG  m   4  PG m
( )   Set A and B with the following parameters：
A n p P n
A ：Pn202 B ：Pn201

- 100 -
4.6.4 Smoothing
A filter can be applied in the servo drive to a constant-frequency reference pulse.
(1)Selecting a Position Reference Filter
Parameter Description
0：1st-order filter
Pn205
1：2nd-order filter
* After changing the parameter, turn OFF the power once and turn it ON again to enable the new setting.
(2)Filter-related Parameters
Position Reference Acceleration/Deceleration Time Constant
Position
Pn204
0～32767 0.1ms 0 Immediately
■Important
When the position reference acceleration/deceleration time constant (Pn204) is changed, a value with no reference
pulse input and a position error of 0 will be enabled. To ensure that the setting value is correctly reflected, stop the
reference pulse from the host controller and input the clear signal (CLR), or turn OFF to clear the error.
This function provides smooth servomotor operation in the following cases.
· When the host controller that outputs a reference that cannot perform acceleration/deceleration processing.
· When the reference pulse frequency is too low.
· When the reference electronic gear ratio is too high (i.e., 10× or more)
- 101 -
4.6.5 Low Frequency Vibration Suppression
（1）Note:
For the low rigidity load, low frequency vibration will occur continually at the front end of the load during fast acceleration
or fast deceleration. The vibration may delay positioning time and affect the productive efficiency.
The function of low frequency vibration suppression is embedded in ProNet series servo drives by calculating the load
position and compensating.
（2）Application:
Low frequency vibration suppression function is enabled in both speed control mode and position control mode.
Low frequency vibration suppression function is disabled or can not reach the expected effect in the following conditions.
 Vibration is pricked up due to an external force.
 Vibration frequency is between 5.0Hz to 50.0Hz.
 There is mechanical clearance at the mechanical connection part.
 The time for movement is less than one vibration period.

（3）How to operate:
 Measuring Vibration frequency
Write the frequency data measured (unit:0.1Hz) directly to Parameter Pn411, if the vibration frequency can be
measured by an instrument (such as a laser interferometer).And it also can be measured indirectly by
communication software ESView or FFT analsis function.
- 102 -
 Related Parameters
Parameter Meaning
H.□0□□ 0:Low frequency vibration suppression function disabled
Pn006
H.□1□□ 1:Low frequency vibration suppression function enabled
Low frequency vibration frequency

Speed Position
Pn411 Setting Range Setting Unit Factory Setting Setting Validation
50～500 0.1Hz 100 Immediately
Low frequency vibration damp
Speed Position
0～200 — 25 Immediately
·Writing the frequency data to parameter Pn411 can adjust Pn411 slightly to obtain the best suppression effect.
·If the servomotor stopped with continuous vibration, Pn412(Do not change in general) should be increased properly.
·Parameter Pn411 and Pn412 are enabled when Pn006.2=1 (Setting validation: after restart).
- 103 -
4.6.6 Positioning Completion Output Signal
This signal indicates that servomotor movement has been completed during position control. Use the signal as an
interlock to confirm that positioning has been completed at the host controller.
CN1-11,CN1-12 ON (low level) Positioning has been
(Factory setting) completed.
Output /COIN
OFF (high level) Positioning is not
completed.
·This output signal can be allocated to an output terminal with parameter Pn511. Refer to 3.2.2 I/O Signal Names and
Functions.
·The factory setting is allocated to CN1-11,12.
Positioning Error
Position
0～5000 1Puls 10 Immediately
Position complete time
Position
Pn520
0~60000 0.1ms 500 Immediately
·The positioning completion (/COIN) signal is output when the difference (position error pulse) between the number of
reference pulses output by the host controller and the travel distance of the servomotor is less than the value set in this
parameter and the stabilization time is more than the value of Pn520.
·Set the number of error pulses in reference unit (the number of input pulses defined using the electronic gear).
·Too large a value at this parameter may output only a small error during low-speed operation that will cause the /COIN
signal to be output continuously.
·The positioning error setting has no effect on final positioning accuracy.
Reference
Speed Servomotor speed
Pn500
Error pulse
(Un011,Un012)
/COIN
(CN1-11,12)
■Note
·/COIN is a position control signal.
·This signal is used for the speed coincidence output /V-CMP for speed control, and it always OFF (high level) for torque
control.
- 104 -
4.6.7 Reference Pulse Inhibit Function (INHIBIT)
(1)Description
This function inhibits the servo drive from counting input pulses during position control.
The servomotor remains locked (clamped) while pulses are inhibited.

Servodrive
Pn005.1
Pn005=H.□□1□
OFF +
Reference pulse
Pn005=H.□□B□ Error Counter
ON -
/P-CON
/P-CON
Feedback pulse
(2)Setting Parameters
Parameter Meaning
Pn005 H.□□B□ Control mode selection：position control(pulse train reference)⇔INHIBIT
■Inhibit(INHIBIT) switching condition
·/P-CON signal ON (low level)
(3)Setting Input Signals

Signal Connector Pin
Type Setting Meaning
Name Number
Turns the INHIBIT function ON.
ON(low level) (Inhibit the servo drive from counting reference
Input /P-CON CN1-15 pulses)
Turns the INHIBIT function OFF.
OFF(high level)
(Counters reference pulses.)
- 105 -
4.6.8 Position Control (contact reference)
Position control under contact reference (parameter Pn005.1＝C). In this mode, servo drive can position with a single
axes without a host controller.
There are 16 position control points with each being able to set move distance, running speed, constants for position
reference filter time, and the stop time when positioning completed. Two speeds (1. speed moving toward distance switch
“speed of looking for reference point”. 2. Speed moving away from distance switch “moving speed.”) of reference points
could be set as:
Two position modes: 1. Absolute position mode 2. Relative position mode
Two running modes: 1. Circling mode 2. Non-circling mode
Two step switching method: 1. Delay step switching 2. /P-CON signal switching
Method of looking for reference points: 1. Forward direction 2. Reverse direction
￭Adjusting offset
Offset of each points has two correspondent parameters: one unit of the parameter is 【x 10000 reference pulse】and the
other is 【x 1 reference pulse】. Setting range of both parameters is: (-9999----+9999), while offset value equals sum of
those two values.
For example:
No.0 offset correspond to parameter Pn600【x 10000 reference pulse】 and Pn601【x 1 reference pulse】. Set Pn600
= 100, Pn601=-100.
No.0 offset value = Pn600x10000 reference pulse + Pn601x1 reference pulse
= 100x10000 reference pulse + (-100)x1 reference pulse
= 999900 reference pulse
With the same principle, we can conclude: in order to get the same results, we also can set Pn600 = 99 and Pn601 =
9900.
Thus, we can see when the two parameters are not zero; we can get same result by two ways: one is to set the two
parameters both negative or both positive, or one negative the other positive.
￭Speed
Speed mentioned here refers to the steady speed during which the motor is running, which is similar to the pulse
frequency given from the external pulse reference in position control.However, this speed has nothing to do with the
electronic gear; it is the actual speed of the motor.
￭Position reference filter time constant

Same as position reference filter time constant Pn204 in common position control.
￭Time for change steps after desired position reached

Apply internal delay to change steps to a valid value in parameter Pn681.1.
Time for change steps outputs from positioning completed signal CON/, from Servo ON, or from the time when reference
point is found till the Servo performs the program to control position of the point. Such period of time depends on step
changing time required by a point number among start point in program.
When running point control program, if error counter is set as “not clear error counter when Servo OFF”, then the error
counter might flood. If it does not flood, then the servo drive will probably run at the max. running speed when Servo ON
again. PLEASE PAY ATTENTION TO THE SAFETY OF INSTRUMENT.
- 106 -
Setting
Para. No. Name and description Default
range
[0] Clear error pulse when S-0FF, not clear error pulse
when overtravel.
Pn004.1 0~2 0
[1] Not clear error pulse
[2] Clear error pulse When S-OFF or over travel
￭Looking for the reference point

Looking for the reference point is for establishing a zero physical point of the operating platform, which is used as zero
point in the coordinates during point position control. And users may choose to find a reference point either in forward or
reverse side.
How to find a reference point
Mount a limit switch in the forward or reverse side.Find a reference point in the forward direction after connecting to /PCL
and in the reverse direction after connecting to /NCL. When the operating platform bumps into the limit the switch, the
motor will first stop according to the way set by Pn004.0, and then rotate again against limit the switch. When the
operating platform leaves the limit switch and the motor reaches the position of first photo encoder Phase C pulse,then
position of operating platform is set to be the zero point of the coordinates.
How to find related parameters of reference point
Speed towards limit switch is called “speed of looking for reference point “, and the moving speed away from limit switch is
called “ moving speed”. These two speeds could be set by the following parameters:
Para. No. Description Unit Setting range Default
Speed of looking for reference point (hits
Pn685 rpm 0~3000 1500
the limit switch)
Moving speed (move away from limit
Pn686 rpm 0~200 30
switch)
Usually, the set speed of the reference point (Pn685) is high, and the moving speed (Pn686) is low. Note: if moving
speed is too high, precision of finding a reference point would be affected.
When looking for a reference point, /PCL and /NCL are no longer programmed to limit external current.
- 107 -
■ Related parameter
Para. No. Description Observation
Choose between cycle run and single run. Changing steps will be performed till
0: Cycle run, /PCL as start signal, /NCL reverse to the end point is completed comma
look for reference point. and the next change will start from
1: Single run, /PCL as start signal, /NCL reverse to the start point during multi-points
Pn681.0 look for reference point. cycle run.
2. Cycle run, /NCL as start signal, /PCL reverse to Point control program will not
look for reference point. change steps after the end point is
3. Single run, /NCL as start signal, /PCL reverse to completed during multi- points single
look for reference point. run.
Change steps by external /P-CON
Change step and start mode
signals. The signal will be valid when
0: Delay changing steps, the start signal is not
drive output reaches the desired
needed.
Pn681.1 position. When input signal changes,
1: Change steps by /P-CON, start signal not needed.
the signal is valid, then steps will be
2. Delay changing steps, need start signal.
changed by consequence from start
3. Change steps by /P-CON, need start signal.
point to end point.
Change step input signal mode
Pn681.2 [0] High or low level
[1] sign pulse
Incremental: relative moving
distance (distance from current point
to next point) programming.
0: Incremental
Pn682 Absolute: absolute moving distance
1: Absolute
(distance between operating
platform and the reference point)
programming.
- 108 -
4.6.9 Position Homing Control (Homing Function)
In position control mode, the servomotor always needs to operate at a fixed position. This position is normally regarded as
the zero position. When the host controller is turned on, the zero position adjustment is required before processing. This
zero position will be regarded as the reference point. ESTUN servo drives can perform this function by the homing
function.
(1)Homing Mode Setting
Para. No. Description

b.□□□0 Homing in the forward direction
b.□□□1 Homing in the reverse direction
b.□□0□ Return to search C-Pulse when homing
Pn689 b.□□1□ Directly search C-Pulse when homing
b.□0□□ Homing function disabled
b.□1□□ Homing triggered by SHOM signal(rising edge)
·Applicable control mode:position control

·Homing operation can only be operated when /COIN is ON.
·Pulses sent from the host controller is disabled when homing
·Homing operation is disabled when in switching control mode.
·Control mode switching is not allowed during homing.
·After changing these parameters, turn OFF the main circuit and control power supplies and then turn
them ON again to enable the new settings.
·A parameter can be used to re-allocate input connector number for the SHOM and ORG signals. Refer
to 3.2.2 I/O Signal Names and Functions.
(2)Related parameter:
Speed of finding reference point (Hitting the origin signal ORG)

Speed of finding reference point (Leaving the origin signal ORG)
Number of error pulses during homing
0~9999 10000 pulses 0 Immediately
Number of error pulses during homing
0~9999 1 pulse 0 Immediately
- 109 -
(3)Input Signal Setting
Type Signal Connector Pin Setting Meaning
Must be allocated by ON=↑(rising edge) Homing is enabled

Input SHOM
Pn509,Pn510 OFF (not rising edge) Homing is disabled
Must be allocated by ON=H ORG is enabled

Input ORG
Pn509,Pn510 OFF=L ORG is disabled
·After changing Pn509 and Pn510, turn OFF the main circuit and control power supplies and then turn
them ON again to enable the new settings.
Allocating Homing Output Signal (/HOME)

Parameter Meaning
+ Terminal - Terminal
Pn511 H.□□□8 CN1-11 CN1-12 The signal is output from output terminal CN1-11,12.
Pn511 H.□□8□ CN1-5 CN1-6 The signal is output from output terminal CN1-5,6.
Pn511 H.□8□□ CN1-9 CN1-10 The signal is output from output terminal CN1-9,10.
·After changing Pn510, turn OFF the main circuit, and control power supplies, and then turn them ON again to enable
the new settings.
·/HOME signal is only enabled at low level.
(4)Description of Homing Operation
Please set Pn689 according to the actual operation in position control mode. When starting the homing function, the
servomotor will run at the speed of Pn685 when detecting the rising edge of SHOM signal; the servomotor will run at the
speed of Pn686 according to the setting of Pn689.1 when detecting the valid ORG signal.
When input ORG and the encoder C-Pulse is being detected, the servo drive will begin to calculate the number of homing
offset pulses. When offset pulses is completed, the servomotor stops and outputs homing completion signal /HOME, then
homing control is completed.
Pn685 (Hitting the origin signal (ORG)) is usually set at high speed, Pn686 (Leaving the origin signal ORG) is usually set
at low speed.
Please be attention that if Pn686 is setting too high, the precision of mechanical zero position will be affected.
After hitting the origin signal ORG, the motor will return to find C-pulse; the figure is shown as below:
Speed Pn 685
(rpm)
Pn 686
Return to find C-pulse

0rpm
Homing offset distance

（ Pn 690 *10000 ＋ Pn 691 ）
Rising edge
SHOM
ORG
Encoder C-pulse
Begin to counter offset distance after the first C -

pulse is produced when leaving zero posiion .
- 110 -
Corresponding position:
After hitting the origin signal ORG, the motor will find C-pulse directly; the figure is shown as below:
Speed Pn 685
rpm
Pn 686
Find C-pulse without
0rpm returning
Homing offset distance

Pn 690 × 10000 ＋ Pn 691
Rising edge
SHOM
ORG
Encoder C-pulse
Begin to counter offset distance after the first C -pulse

is produced when leaving zero posiion.
Corresponding position:
Mechanical shaft
Machine moves, return to search

pulse C
Begin to counter offset distance after

the first C-pulse is produced when
Motor slow down
leaving zero posiion.
Encoder C-pulse
ORG
Rising edge
SHOM
- 111 -
4.7 Operating Using Torque Control
The following parameters must be set for torque control operation with analog voltage reference.
Parameter Meaning
Pn005 H.□□2□ Control mode selection：Torque control(analog voltage reference)
Torque Reference Input Gain

10～100 0.1V/100% 33 Immediately
This sets the analog voltage level for the torque reference(T-REF) that is necessary to operate the servomotor at the
rated torque.
■Example
Pn400=30：The servomotor operates at the rated torque with 3V input (factory setting).
Pn400=100：The servomotor operates at the rated torque with 10V input.
Pn400=20：The servomotor operates at the rated torque with 2V input.
- 112 -
4.7.2 Torque Reference Input
By applying a torque reference determined by the analog voltage reference to the servo drive, the servomotor torque can
be controlled in proportion with the input voltage.

Type Signal Name Connector Pin Number Meaning
T-REF+ CN1-26
Input Torque Reference Input
T-REF- CN1-27
Used during torque control (analog voltage reference) 300
(Pn005.1=2，6，8，9) Reference torque（%）

200
The torque reference input gain is set in Pn400. For setting
details, refer to 4.7.1 Setting Parameters. 100
■Input specifications -12 -8 -4

0 3 4 8 12
· Input range:DC±0～±10V/rated torque Factory setting Input voltage(V)
-100
· Factory setting
Pn400=30：Rated torque at 3V -200 Set the slope with Pn400.
+3V input：Rated torque in forward direction

-300
+9V input：300% rated torque in forward direction
-0.3V input：10% rated torque in reverse direction
The voltage input range can be changed with parameter Pn400.
Servodrive
470O
■Input circuit example 1/2W min. CN1
Use twisted-pair wires as a countermeasure against noise. T-REF+

26
2KO
+12V T-REF- 27
GND
■Checking the internal torque reference
1.Checking the internal torque reference with the panel operator.
Use the Monitor Mode(Un003). Refer to 5.1.6 Operation in Monitor Mode.
2.Checking the internal torque reference with an analog monitor.
The internal torque reference can also be checked with an analog monitor.
- 113 -
4.7.3 Adjusting the Reference Offset
(1)Automatic Adjustment of the Torque Reference Offset

When using torque control, the servomotor may rotate slowly even when 0V is specified as the analog reference voltage.
This occurs when the host controller or external circuit has a slight offset (measured in mv) in the reference voltage. In this
case, the reference offset can be adjusted automatically and manually using the panel operator.
The automatic adjustment of analog(speed,torque) reference offset(Fn003) automatically measures the offset and adjusts
the reference voltage.
The servo drive performs the following automatic adjustment when the host controller or external circuit has an offset in
the reference voltage.
After completion of the automatic adjustment, the amount of offset is stored in the servo drive. The amount of offset can
be checked in the manual adjustment of torque reference offset(Fn004).
The automatic adjustment of analog reference offset(Fn003) cannot be used when a position loop has been formed with
the host controller and the error pulse is changed to zero at the servomotor stop due to servolock.
Use the torque reference offset manual adjustment(Fn004).
Note：
The analog reference offset must be automatically adjusted with the servo OFF.
(2)Manual Adjustment of the Torque Reference Offset

Manual adjustment of the torque reference offset(Fn004) is used in the following cases.
·If a position loop is formed with the host controller and the error is zeroed when servolock is stopped.
·To deliberately set the offset to some value.
·Use this mode to check the offset data that was set in the automatic adjustment mode of the torque reference offset.
This mode operates in the same way as the automatic adjustment mode(Fn003), except that the amount of offset is
directly input during the adjustment.
The offset adjustment range and setting unit are as follows.
- 114 -
4.7.4 Limiting Servomotor Speed During Torque Control
During torque control, the servomotor is controlled to output the specified torque, which means that the servomotor speed
is not controlled. Accordingly, when an excessive reference torque is set for the mechanical load torque, it will prevail over
the mechanical load torque and the servomotor speed will greatly increase.
This function serves to limit the servomotor speed during torque control to protect the machine.
Without Speed Limit With Speed Limit
(1)Speed Limit Enable

Parameter Description
b.□□0□ Use the value set in Pn406 as the speed limit （Internal speed limit ）
Pn001 Use the lower speed between V-REF and Pn406 as an external speed limit
b.□□1□
input.(External speed limit)
(2)Speed Limit During Torque Control

Speed Limit During Torque Control
Torque
Pn406
·Set the servomotor speed limit value during torque control.
·Pn005=H.□□1□，Pn406 is motor speed limit value.
·The servomotor’s maximum speed will be used when the setting in this parameter exceeds the maximum speed of the
servomotor used.
- 115 -
(3)External Speed Limit Function

V-REF+ CN1-1
Input External Speed Limit Input
V-REF- CN1-2
·Inputs an analog voltage reference as the servomotor speed limit value during torque control.
·The smaller value is enabled, the speed limit input from V-REF or the Pn406 (speed limit during torque control) when
Pn005=H.□□1□.
·The setting in Pn300 determines the voltage level to be input as the limit value. Polarity has no effect.
Speed Reference Input Gain

0~3000 rpm/v 150 Immediately
·Set the voltage level for the speed that is to be externally limited during torque control.
4.8 Operating Using Speed Control with an Internally Set Speed
The function of internally set speed selection allows speed control operation by externally selecting an input signal from
among seven servomotor speed setting made in advance with parameters in the servo drive. The speed control
operations within the three settings are valid. There is no need for an external speed or pulse generator.
- 116 -
Parameter Meaning
Pn005 H.□□3□ Control mode selection:
Speed control(contact reference) Speed control(zero reference)
Internal set speed 1 speed
Pn316
-6000～6000 rpm 100 Immediately
Pn317
Pn318
Pn319
-6000～6000 rpm -100 Immediately
Pn320
Pn321
Pn322

(Note):The servomotor’s maximum speed will be used whenever a speed setting for the Pn316～Pn322 exceeds the
maximum speed.
- 117 -
4.8.2 Input Signal Settings
The following input signals are used to switch the operating speed.
Type Signal Name Connector Pin Number Meaning
Input /P-CON CN1-15 Selects the internally set speed.
Input /P-CL CN1-41 Selects the internally set speed.
Input /N-CL CN1-42 Selects the internally set speed.
4.8.3 Operating Using an Internally Set Speed
Use ON/OFF combinations of the following input signals to operate with the internally set speeds.
When Pn005.1=3: Selects the internally set speed (contact reference) Speed control (zero reference)
Input Signal
Speed
/P-CON /P-CL /N-CL
OFF(H) OFF(H) Speed control (zero reference)
OFF(H) ON(L) SPEED1

OFF(H)
ON(L) OFF(H) SPEED2
ON(L) ON(L) SPEED3
OFF(H) OFF(H) SPEED4
OFF(H) ON(L) SPEED5

ON(L)
ON(L) OFF(H) SPEED6
ON(L) ON(L) SPEED7

Note: OFF= High level; ON= Low level
■Control Mode Switching

When Pn005.1 = 4，5，6, and either /P-CL or /N-CL is OFF (high level), the control mode will switch.
Example:
When Pn005.1=5: Speed control(contact reference) Position control (pulse train)
Input Signal
Speed
/P-CON /P-CL /N-CL
OFF(H) OFF(H) Pulse train reference input (position control)
OFF(H) ON(L) SPEED1

OFF(H)
ON(L) OFF(H) SPEED2
ON(L) ON(L) SPEED3
OFF(H) OFF(H) SPEED4
OFF(H) ON(L) SPEED5

ON(L)
ON(L) OFF(H) SPEED6
ON(L) ON(L) SPEED7
- 118 -
4.9 Limiting Torque
The servo drive provides the following three methods for limiting output torque to protect the machine.
NO. Limiting Method Reference Section
1 Internal torque limit 4.9.1
2 External torque limit 4.9.2
3 Torque limiting by analog voltage reference 4.9.3
4.9.1 Internal Torque Limit
Maximum torque is always limited to the values set in the following parameters.
Forward Torque Limit
Pn401 Setting Range Setting Unit Factory Seeting Setting Validation
Reverse Torque Limit
Pn402 Setting Range Setting Unit Factory Seeting Setting Validation
·The setting unit is a percentage of rated torque.
·The maximum torque of the servomotor is used, even though the torque limit is set higher than the maximum torque of
the servomotor. (as is the case with the 300% factory setting)
With No Internal Torque Limit

With Internal Torque Limit
Maximum torque can be output
Pn402
t
t
Pn401
Speed Speed
Limiting torque
Maximum torque
■Note:
Too small a torque limit setting will result in insufficient torque during acceleration and deceleration.
- 119 -
4.9.2 External Torque Limit
This function allows the torque to be limited at specific times during machine operation, for example, during press stops
and hold operations for robot workpieces.
An input signal is used to enable the torque limits previously set in parameters.
(1)Related Parameters
Forward External Torque Limit
Reverse External Torque Limit
Note: The setting unit is a percentage of rated torque (i.e., the rated torque is 100%).
(2)Input Signals
Signal Connector Pin
Type Setting Meaning Limit Value
Name Number
CN1-41 ON(low level) Forward external torque limit Pn403
Input /P-CL
(factory setting) OFF(high level) Forward internal torque limit Pn401
CN1-42 ON(low level) Reverse external torque limit Pn404
Input /N-CL
(factory setting) OFF(high level) Reverse internal torque limit Pn402
When using this function, make sure that there are no other signals allocated to the same terminals as /P-CL and /N-CL.
(3)Changes in Output Torque during External Torque Limiting
Example: External torque limit (Pn401，Pn402) set to 300%

/P-CL(Forward External Torque Limit Input)
High level Low level
Pn402
Torque
High 0
level
Pn403
Speed
/N-CL
(Reverse
External
Torque Pn404
Torque
Limit Input)
Low
0
level
Speed
Pn401
Note: Select the servomotor rotation direction by setting Pn001=b.□□□0 (standard setting, CCW=Forward direction).
- 120 -
4.9.3 Torque Limiting Using an Analog Voltage Reference
Torque limiting by analog voltage reference limits torque by assigning a torque limit in an analog voltage to the T-REF
terminals (CN1-26,27). This function can be used only during speed or position control, not during torque control.
Refer to the following block diagram when the torque limit with an analog voltage reference is used for speed control.
Important：
·There is no issue with input voltage polarity of the analog voltage reference for torque limiting.
·The absolute values of both + and – voltages are input, and a torque limit value corresponding to that absolute
value is applied in the forward or reverse direction.
Related Parameters
Parameter Meaning
Pn001 b.□1□□ Use the T-REF terminal to be used as an external torque limit input.
- 121 -
4.10 Control Mode Selection
The methods and conditions for switching the servo drive control modes are described below.
The following control mode combinations can be selected according to the individual application of the user.
Parameter Control Method
H.□□4□ Speed control (contact reference) Speed control (analog voltage reference)
H.□□5□ Speed control (contact reference) Position control (pulse train reference)
H.□□6□ Speed control (contact reference) Torque control (analog voltage reference)
H.□□7□ Position control (pulse train reference) Speed control (analog voltage reference)
H.□□8□ Position control (pulse train reference) Torque control (analog voltage reference)
Pn005 H.□□9□ Torque control (analog voltage reference) Speed control (analog voltage reference)
H.□□A□ Speed control (analog voltage reference) Zero clamp
H.□□B□ Position control (pulse train reference) Position control (inhibit)
H.□□C□ Position control (contact reference)
H.□□D□ Speed control (Parameter reference)
H.□□E□ Special control
4.10.2 Switching the Control Mode
Switching Speed Control (Pn005.1=4，5，6)
With the sequence input signals in the factory setting, the control mode will switch when both /P-CL and /N- CL signals
are OFF (high level).
Input /P-CL CN1-41 (factory setting) OFF (high level)

Switches control mode.
Input /N-CL CN1-42 (factory setting) OFF (high level)
- 122 -
4.11 Other Output Signals
4.11.1 Servo alarm output
The following diagram shows the right way to connect the Alarm Output.
An external +24V I/O power supply is required since there is no +24V power source available inside the servo drive.
Output → ALM+ 1CN- 7 Servo alarm output
Output → ALM- 1CN- 8 Servo alarm output uses grounding signal
ALM outputs a signal when the servo drive is detected in an abnormal state.
Normally, the external circuit consists of /ALM should be able to switch off the power of servo drive.
Signal Status Output level Comments

ON 1CN-7：“L” level Normal state
ALM
OFF 1CN-8：“H” level Alarm state
When “servo alarm(ALM)” happens, always remove alarm reasons first , and then turn the input signal "/ALM-RST" to ON
position to reset alarm status.
→ Input /ALM-RST 1CN- 39 alarm reset input
Signal Status Input level Comments

ON 1CN-39：“L” level Reset servo alarm
/ALM-RST
OFF 1CN-39：“H” level Do not reset servo alarm
Normally, the external circuit can switch off the power supply of the servo drive when an alarm occurs. When
powered on again, the servo drive removes the alarm automatically, so the alarm reset is not required to be connected. In
addition, the alarm reset is enabled with the panel operator.
Note: When an alarm occurs, remove the alarm reason before resetting the alarms.
- 123 -
4.11.2 Rotation Detection Output Signal (/TGON)

Servomotor is operating(Servomotor
ON(low level)
speed is above the setting in Pn503).
CN1-5,CN1-6
Output /TGON Servomotor is not
(Factory setting) OFF(high
operating(Servomotor
level)
speed is below the setting in Pn503).
This signal output indicates that the servomotor is curently operating above the setting set in parameter Pn503.
·Related parameter
Rotation Detection Speed TGON
Pn503
Setting range Setting unit Factory setting Setting validation
·This parameter sets the range in which the rotation detection output signal (/TGON) is output
·When the servomotor rotation speed is above the value set in the Pn503,the servomotor rotation speed signal
(/TGON) is output.
·The rotation detection signal can also be checked on the panel operator.
4.11.3 Servo Ready (/S-RDY) Output

CN1-9,CN1-10 ON (low level) Servo is ready.
Output /S-RDY
(factory setting) OFF (high level) Servo is not ready.
·This signal indicates that the servo drive received the servo ON signal and completed all preparations.
·It is an output when there are no servo alarms and the main circuit power supply is turned ON.
4.11.4 Encoder C Pluse Output (/PGC)
Not including this setting in ON (low level) With encoder C pluse output
the default setting,
Output /PGC please choose terminal Without encoder C pluse
OFF (high level)
output by setting output
parameter Pn511.
This signal indicates when the servo drive circumrotates to the C pulse position; there is a correlation between the width
of the C pulse and the speed of the servo drive.
- 124 -
4.11.5 Over travel signal output (OT)
Not including this Without forward rotation

ON (low level) Prohibited (POT) and reverse rotation
setting in the default
prohibited (NOT) signal
setting,please choose
Output OT
terminal output by With forward rotation
OFF (high level) Prohibited (POT) and reverse rotation
setting parameter
prohibited (NOT) signal
Pn511
When machine is on over travel state,OT signal is OFF;Host controller can use this signal to stop sending
reference.
Related parameter
POT/NOT
Pn000
Setting Range Unit Factory Setting Setting Validation
0～1111 － 0 After restart
Pn000.1＝1,external POT disabled;Pn000.2＝1, external NOT disabled;
Pn000.1＝1 and Pn000.2＝1,OT signal is ON.
4.11.6 Servo Enabled Motor Excitation Output(/RD)

Not including this setting in
ON＝L Servo enabled motor excitation
the default setting,please
Output /RD
choose terminal output by
OFF＝H Servo disabled motor not excitation
setting parameter Pn511
/RD is on when servo enabled motor excitation.
4.11.7 Torque Limit Detection Output (/CLT)
The application of output signal /CLT is as follows:
Servo Drive
24V Power
supply
Photocoupler output +24V
1CN- /CLT+
Max.applicable Voltage：
DC30V
Max.applicable current： 1CN- /CLT-
DC50mA
－>Output /CLT Torque limit output Speed, torque control, position control
- 125 -
Indicates the output torque (current) of motor is limited.

Motor output torque under limit (Internal
Not including this setting in
ON＝L torque reference is higher than setting
the default setting,please
Output /CLT value).
choose terminal output by
No torque limit (Internal torque reference
setting parameter Pn511 OFF＝H
is lower than setting value).
Please use the following user constants to define output signals and pins when using /CLT signal.

Para. No. Meaning
+Terminal -Terminal
Pn511 H.□□□3 CN1-11 CN1-12 Output signal of CN1-11，CN1-12 is /CLT
Pn511 H.□□3□ CN1-05 CN1-06 Output signal of CN1-5，CN1-6 is /CLT
Pn511 H.□3□□ CN1-09 CN1-10 Output signal of CN1-9，CN1-10 is /CLT
Pn511.0=3
1CN-11,1CN-12
/CLT
Torque limit Pn511.1=3
output 1CN-05,1CN-06
Pn511.2=3
1CN-09,1CN-10
Output terminal
0 /COIN (/V-CMP) output
- 126 -
4.11.8 Torque Detection Output (/TCR)

Not including this setting in Motor output torque is higher than Pn529
ON＝L
the default setting,please setting value.
Output /TCR
choose terminal output by Motor output torque is lower than Pn529
OFF＝H
setting parameter Pn511 setting value.
Torque detection output time is set by Pn530.
0 /COIN (/V-CMP) output
4.12 Online Autotuning
4.12.1 Online Autotuning
Online autotuning calculates the load moment of inertia during operation of the servo drive and sets parameters so that
the servo gains are consistent with the machine rigidity.
Online autotuning may not be effective in the following cases:
• The motor high speed is lower than 100 rpm.
• The motor acceleration or deceleration is lower than 5000rpm/s.
• Load rigidity is low and mechanical vibration occurs easily or friction is high.
•The speed load moment is changed greatly.
• Mechanical gas is very large.
If the condition meets one of the above cases or the desired operation cannot be achieved by the online autotuning,
set the value in Pn106 (Load inertia percentage) and perform the adjustment manually.
- 127 -
4.12.2 Online Autotuning Procedure
！WARNING
￭Do not perform extreme adjustment or setting changes causing unstable servo operation.Failure to observe
this warning may result in injury and damages to the machine.
￭ Adjust the gains slowly while confirming motor operation.
Start
Operate with factor setting.

（Set Pn100=1）
Operation OK？ Yes
No
No Load moment of inertia

varies?
Yes
Continuous online autotuning

（Pn100=1、2、3、4、5、6）
Operation OK? Yes
No
Adjust the machine rigidity setting

（Set at Pn101）
Operation OK？ Yes
No
Do not perform online autotuning.

（Set Pn100=0）
End
- 128 -
4.12.3 Setting Online Autotuning
Related parameters:
Parameter Setting Factory Setting
Name Unit
No. Range Setting Invalidation
Online autotuning setting
0:Manual gain adjustment
1,2,3= Normal mode;4,5,6=Vertical load
Pn100 — 0~6 1 After restart
1,4 = Load inertia without variation;
2,5 = Load inertia with little variation;
3,6= Load inertia with great variation
Pn101 Machine rigidity setting — 0~15 5 Immediately
Speed gain acceleration relationship during

online autotuning
Pn128 — 0~3 3 Immediately
If the setting is greater, the servo gain will
increase.
4.12.4 Machine Rigidity Setting for Online Autotuning
There are 16 machine rigidity settings for online autotuning, When the machine rigidity setting is selected, the servo
gains (speed loop gain, speed loop integral time constant, position loop gain) are determined automatically. The
factory setting for the machine rigidity setting is 5.
Machine Position Loop Gain【s-1】 Speed Loop Gain【Hz】 Speed Loop Integral Time
Rigidity Setting Pn104 Pn102=Pn104*( Pn128+1) Constant【0.1ms】
Pn103
0 10 40 800
1 15 60 600
2 20 80 450
3 25 100 400
4 30 120 300
5 40 160 200
6 65 260 140
7 80 320 110
8 100 400 90
9 120 480 80
10 140 560 70
11 160 640 60
12 180 720 55
13 210 840 50
14 250 1000 40
15 300 1200 30
- 129 -
Chapter 5
Panel Operator
5.1 Basic Operation
5.1.1 Functions on Panel Operator
The panel operator is a built-in operator that consists of display section and keys located on the front panel of the servo
drive.
Parameter setting, status display ,and execution of utility function are enabled using the panel operator.
The names and functions of the keys on the panel operator are shown as follows:
MODE INC DEC ENTER
Panel Corresponding
Function
Symbol Key Name
·To display the parameter settings and setting values.
▲ INC key
·To increase the setting value.
▼ DEC key
·To decrease the setting value.
·To select a basic mode, such as the display mode, parameter setting
M MODE key mode, monitor mode, or utility function mode.
·To save the setting during parameter setting and exit.
◄ ENTER key To display the parameter settings and setting values, and release ararm.
Note: In this manual, the Panel Symbol is represented by Corresponding Key Name for easy understanding.
5.1.2 Resetting Servo Alarms
Servo alarms can be reset by pressing the ENTER key when the panel operator in display mode. Servo alarms can also
be reset using the CN1-39(/ALM-RST) input signal.
There is no need to clear the servo alarms if it turns the main circuit power supply OFF.
Note：After an alarm occurs, remove the cause of the alarm before resetting it.
- 130 -
5.1.3 Basic Mode Selection
The basic modes include status display mode, parameter setting mode, monitor mode, and utility function mode. Each
time the MODE key is pressed, the next mode in the sequence is selected.
Select a basic mode to display the operation status, set parameters and operation references.
The basic mode is selected in the following order.
Power ON
Status display mode
Parameter setting mode
Monitor mode
Utility function mode
5.1.4 Status Display Mode
The status display mode displays the servo drive status as bit data and codes.
Selecting Status Display Mode
The status display mode is selected when the power supply is turned ON. If it is not displayed, select this mode by
pressing MODE key.
Note that the display differs between the speed/torque control and position control types.
- 131 -
 Bit Data Display

Speed/Torque Control Mode Position Control Mode
No.
Bit Data Description Bit Data Description
Lit when the difference between the
Lit if error between position reference
servomotor and reference speed is the
and actual servomotor position is below
Speed same as or less than the preset value. Positioning
1
○ preset value.
Coincidence Present value:Pn501 (factory setting is Completion
Present value:Pn500(10 pulse is factory
10rpm )
setting)
Always lit in torque control mode.
2
○ Base lock Lit for base block. Not lit at servo ON. Base block Lit for base block. Not lit at servo ON.
Control Control Lit when servo drive control power is

3
○ Lit when servo drive control power is ON.
power ON power ON ON.
Lit if input speed reference exceeds preset
Speed value. Not lit if input speed reference is Lit if reference pulse is input.
Reference
4
○ reference below preset value. Not lit if no reference pulse is input.
pulse input
input Preset value：Pn503(factory setting is 20
rpm)
Lit if input torque reference exceeds preset
Torque value. Error Lit when error counter clear signal is
5
○ reference Not lit if input torque reference is below counter clear input. Not lit when error counter clear
input preset value. signal input signal is not input.
Preset value：10％ of rated torque
Lit when main circuit power supply is ON Lit when main circuit power supply is
and normal. ON and normal.
6
○ Power ready Power ready
Not lit when main circuit power supply is Not lit when main circuit power supply is
OFF. OFF.
Lit if servomotor speed exceeds preset Lit if servomotor speed exceeds preset
Rotation value.Not lit if servomotor speed is below Rotation value. Not lit if servomotor speed is
7
○ detection preset value. detection below preset value.
/TGON Preset value: Pn503 (factory setting is 20 /TGON Preset value: Pn503(factory setting is
rpm) 20 rpm)
 Codes Display
Code Meaning
Baseblock
Servo OFF (servomotor power OFF)
Run
Servo ON（servomotor power ON）
Forward Run Prohibited
CN1-16（P-OT）is OFF.
Reverse Run Prohibited
CN1-17（N-OT）is OFF.
Alarm Status
Displays the alarm number.
Press ENTER key to clear the present servo alarm.
- 132 -
5.1.5 Operation in Parameter Setting Mode
The servo drive offers a large number of functions, which can be selected or adjusted by the parameter settings. Refer to
A.1 Parameter List for details.
■Parameter Setting Procedures
The parameter settings can be used for changing parameter data. Before changing the data, check the permitted range of
the parameter.
The example below shows how to change parameter Pn102 from “100” to “85”.
1． Press MODE key to select the parameter setting mode.
2． Press INC key or DEC key to select parameter number.
3． Press ENTER key to display the current data of Pn102.
4． Press the INC or DEC key to change the data to the desired number 00085. Hold the key to accelerate the changing
of value. When the maximum value or minimum value is reached, pressing INC or DEC key respectively, will have no
effect.
5． Press the ENTER or MODE key once to return to the display of Pn102.
- 133 -
5.1.6 Operation in Monitor Mode
The monitor mode allows the reference values input into the servo drive, I/O signal status, and servo drive internal status
to be monitored.
■Using the Monitor Mode
The example below shows how to display the value (1500) stored in Un001.
1.Press MODE key to select the monitor mode.
2.Press the INC or DEC key to select the monitor number to display.
3.Press the ENTER key to display the data for the monitor number selected at step 2.
4.Press the ENTER key once more to return to the monitor number display.
- 134 -
■List of Monitor Modes
Contents of Monitor Mode Display
Monitor Number Monitor Display

Un000 Actual servomotor speed Unit: rpm
Un001 Input speed reference Unit:rpm
Input torque reference Unit:%
Un002
(with respect to rated torque)
Internal torque reference Unit:% Internal status bit display
Un003
(with respect to rated torque) 7 6 5 4 3 2 1 0
Un004 Number of encoder rotation angle pulses
Un005 Input signal monitor
Un006 Encoder signal monitor
Un007 Output signal monitor
Un008 Frequency given by pulse Unit:1kHZ
Un009 Number of servomotor rotation pulses
4
Un010 Pulse rate of servomotor rotated（x10 ）
Un011 Error pulse counter lower 16 digit
Un012 Error pulse counter higher 16 digit
Un013 Number of pulses given
Un014 Number of pulses given（×10000）
Un015 Load inertia percentage
Un016 Servomotor overload ratio
Only used in ProNet-7.5kW～22kW when
Un017 Servomotor winding temperature
equipped with resolver.
- 135 -
Contents of Bit Display：
Monitor Number Display LED Number Content

0 /S-ON（CN1-14）
1 /PCON（CN1-15）
2 P-OT（CN1-16）
3 N-OT（CN1-17）
Un005
4 /ALM-RST（CN1-39）
5 /CLR（CN1-40）
6 /PCL（CN1-41）
7 /NCL（CN1-42）

0 （Not used）
1 （Not used）
2 （Not used）
3 Phase-C
Un006
4 Phase-B
5 Phase-A
6 （Not used）
7 （Not used）

0 CN1_05，CN1_06
1 CN1_07，CN1_08
Un007
2 CN1_09，CN1_10
3 CN1_11，CN1_12
- 136 -
5.2 Operation in Utility Function Mode
In utility function mode, the panel operator can be used to run and adjust the servo drive and servomotor.
The following table shows the parameters in the utility function mode.
Parameter No. Function
Fn000 Alarm traceback data display
Fn001 Parameter setting initialization
Fn002 JOG mode operation
Fn003 Automatic adjustment of speed reference offset
Fn004 Manual adjustment of speed reference offset
Fn005 Automatic adjustment of servomotor current detection
Fn006 Manual adjustment of servomotor current detection
Fn007 Software version display
Fn008 Position teaching
Fn009 Static inertia detection
Fn010 Absolute encoder multiturn data and alarm reset
Fn011 Absolute encoder related alarms reset
Note: Fn010、Fn011 only can be used when the servomotor mounted the absolute encoder.
5.2.1 Alarm Traceback Data Display
The alarm traceback display can display up to 10 previously occurred alarms.The alarm is displayed on Fn000, which is
stored in the alarm traceback data.
Follow the procedures below to confirm alarms which have been generated.
2. Press the INC or DEC key to select the function number of alarm trace back data display.
3. Press the ENTER key once, the latest alarm data is displayed.
Alarm Sequence Number Alarm Code
4. Press the INC or DEC key to display other recent alarms that have occurred.
5. Press the ENTER key, the display will return to Fn000.
Note: Hold the ENTER key for one second with alarm code displaying, all the alarm traceback datas will be cleared.
- 137 -
5.2.2 Parameter Settings Initialization
Follow the procedures below to execute the parameter settings initialization.

2. Press the INC or DEC key to select the function number of parameter settings initialization.
3. Press the ENTER key to enter into parameter settings mode.
4. Hold the ENTER key for one second, the parameters will be initialized.
5. Release the ENTER key to ruturn to the utility function mode display Fn001.
Note：
Press the ENTER key during servo ON does not initialize the parameter settings.
Initialize the parameter settings with the servo OFF.
- 138 -
5.2.3 Operation in JOG Mode
Follow the procedures below to operate the servomotor in JOG mode.

2. Press the INC or DEC key to select the function number of JOG mode operation.
3. Press the ENTER key to enter into JOG operation mode.
4. Press the MODE key to enter into servo ON (servomotor power ON) status.
5. Press the MODE key to switch between the servo ON and servo OFF status.The servo drive must be in servo ON
status when the servomotor is running.
6. Press the INC or DEC key to rotate the servomotor.
7. Press the ENTER key to return to utility function mode display Fn002. Now the servo is OFF(servomotor power OFF).
- 139 -
5.2.4 Automatic Adjustment of the Speed Reference Offset
When using the speed/torque (analog reference) control, the servomotor may rotate slowly even if 0V is specified as the
analog voltage reference.
This happens if the host controller or external circuit has a slight offset (in the unit of mV) in the reference voltage.
The reference offset automatic adjustment mode automatically measures the offset and adjusts the reference voltage. It
can adjust both speed and torque reference offset.
The servo drive automatically adjusts the offset when the host controller or external circuit has the offset in the reference
voltage.
After completion of the automatic adjustment, the amount of offset is stored in the servo drive. The amount of offset can be
checked in the speed reference offset manual adjustment mode (Fn004). Refer to 4.5.3 (2) Manual Adjustment of the
Speed Reference Offset.

The automatic adjustment of reference offset (Fn003) cannot be used when a position loop has been formed with a host
controller and the error pulse is changed to zero at the servomotor stop due to servolock. Use the speed reference offset
manual adjustment for a position loop.
The zero-clamp speed control function can be used to force the servomotor to stop while the zero speed reference is
given.
Note: The speed reference offset must be automatically adjusted with the servo OFF.
Adjust the speed reference offset automatically in the following procedure.
1. Turn OFF the servo drive, and input the 0V reference voltage from the host controller or external circuit.

3. Press the INC or DEC key to select the utility function number Fn003.
4. Press the ENTER key to enter into the speed reference offset automatic adjustment mode.
5. Press the MODE key for more than one second, the reference offset will be automatically adjusted.
- 140 -
6. Press the ENTER key to return to the utility function mode display Fn003.
7. Thus, the speed reference offset automatic adjustment is complete.
5.2.5 Manual Adjustment of the Speed Reference Offset
Manual adjustment of the speed/torque reference offset is used in the following cases:
 If a position loop is formed with the host controller and the error is zeroed when servolock is stopped.
 To deliberately set the offset to some value.
Use this mode to check the offset data that was set in the automatic adjustment mode of the speed/torque reference
offset.
This mode operates in the same way as the automatic adjustment mode, except that the amount of offset is directly input
during the adjustment.
The offset adjustment range and setting unit are as follows.
Note:
When the offset using in automatic adjustment exceeds the manual adjustment range (-1024~+1024），
manual adjustment will be invalid.
Adjust the analog reference offset manually in the following procedure:

3. Press the ENTER key to enter into the speed reference offset manual adjustment mode.
- 141 -
4. Turn ON the servo-ON signal, the display is shown as follows:
5. Hold the ENTER key, the speed reference offset will be displayed.
6. Press the INC or DEC key to change the offset.

7. Hold the ENTER key to return to the display in step 4.
8. Press ENTER key to return to the utility function mode display Fn004..
Thus, the speed reference offset manual adjustment is complete.
5.2.6 Offset-adjustment of Servomotor Current Detection Signal
Automatic servomotor current detection offset adjustment is performed at ESTUN before shipping. Basically, the user
does not need to perform this adjustment.
Perform this adjustment only if highly accurate adjustment is required for reducing torque ripple caused by current offset.
This section describes the automatic and manual servomotor current detection offset adjustment.
Note：
·Offset-adjustment of the servomotor current detection signal is possible only while power is supplied to the main
circuit power supply and with the servo is the OFF state.
·Execute the automatic offset adjustment if the torque ripple is too big when compared with that of other servo
drives.
·If this function, particularly manual adjustment, is executed carelessly, it may worsen the characteristics.
■Automatic Offset-adjustment of Servomotor Current Detection Signal

Adjust the servomotor current detection signal automatically in the following procedure:

3. Press the ENTER key to enter into the automatic adjustment of the servomotor current detection signal mode.
4. Press the MODE key,the display will blinks for one second. The offset will be automatically adjusted.
- 142 -
Thus, the automatic offset-adjustment of the servomotor current detection signal is complete.
■Manual Offset-adjustment of Servomotor Current Detection Signal

Adjust the servomotor current detection signal manually in the following procedure.
3. Press the ENTER key to enter into the manual adjustment of the servomotor current detection signal.
4. Press the MODE key to switch between the phase U(o _ CuA) and phase V(1_ Cub) servomotor current detection
offset adjustment.
5. Hold the ENTER key for one second to display the phase V offset amount.
6. Press the INC or DEC key to adjust the offset.
7. Press the ENTER key for one second to return to the display in step 3 or 4.
Thus, the manual offset-adjustment of the servomotor current detection signal is completed.
Note:
The adjusting range of the servomotor current detection offset is -1024 to +1024.
- 143 -
5.2.7 Software Version Display
Select Fn007 in utility function mode to check the current software version of the drive.
3. Press the ENTER key to display the DSP software version (the highest bit displays d or E or F or 0).
4. Press the MODE key to display the FGPA/CPLD software version (the highest bit displays P).
5. Press the MODE key to return to DSP software version display.

5.2.8 Position Teaching Function
Perform the position teaching function in the following procedure.

3. Press the ENTER key, the display will be shown as below.
5. Release the ENTER key to complete position teaching function.
5.2.9 Static Inertia Detection

4. Press the MODE key to rotate the servomotor, and the servomotor dynamic speed will be displayed.
5. The unit of the servomotor and load total inertia displayed when servomotor stops is kg.cm²
- 144 -
Thus, the static inertia detection is complete.
Note：Make sure that the servomotor completes at least 6 full revolutions in the CCW direction before detection.
5.2.10 Absolute Encoder Multiturn Data and Alarm Reset

4. Press the MODE key to reset the absolute encoder multiturn data and alarm.
5. Thus the absolute encoder multiturn data and alarm reset is complete.
Important:
This function will clear the absolute position of the encoder; the mechanical safety must be noted.
When the multiturn data is cleared, other encoder alarms will be reset at the same time.
5.2.11 Absolute Encoder Related Alarms Reset

4. Press the MODE key to clear the alarms.
5. Thus the absolute encoder related alarms reset is complete.
- 145 -
Chapter 6
MODBUS Communication
6.1 RS-485 Communication Wiring
ProNet series servo drives provide the MODBUS communication function with RS-485 interface,
which can be used to easily set parameters or to perform monitoring operations and so on.
The definitions of the servo drive communication connector terminals are as follows.
CN3：
1 —
Reserved
2 —
4 ISO_GND
Isolated ground
5 ISO_GND
Note: Do not short terminal 1 and 2 of CN3.
CN4：
1 — Reserved
2 — Reserved
4 ISO_GND
Isolated ground
5 ISO_GND
Note：
1. The length of the cable should be less than 100 meters and in a environment with minimal electrical
disturbance/interference. However, if the transmission speed is above 9600bps, please use the communication cable
within 15 meters to ensure transmission accuracy..
2. A maximum of 31 servo drives can be connected when RS485 is used. Terminating resistances are used at both ends
of the 485 network. If more devices are wanted to connect, use the repeaters to expand.
3. CN3 of servo drive is always used as communication cable input terminal，and CN4 is always used as communication
cable output terminal(If still need to connect slave stations，the communication cable is connected from CN4 terminal to
the next slave station; if need not, add balance resistor in CN4 terminal.).It is prohibited to connect CN3 of any two servo
- 146 -
drives directly when multiple ProNet series servo drives are connected.
Example:
When a RS-485 network is composed of a PLC and three servo drives (A, B, and C), the cable wiring is shown as follows:
PLC→CN3 of A, CN4 of A→CN3 of B, CN4 of B→CN3 of C, CN4 of C→120Ω terminating resistance.
6.2 MODBUS Communication Related Parameters
Setting
Parameter No. Description Control Mode Meaning
Validation
Pn700.0 MODBUS baud rate
[0] 4800bps
[1] 9600bps
[2] 19200bps
Pn700.1 Communication protocol
selection
[0] 7，N，2（MODBUS,ASCII）
[1] 7，E，1（MODBUS,ASCII）
[2] 7，O，1（MODBUS,ASCII）
Pn700 Hex After restart ALL [4] 8，E，1（MODBUS,ASCII）
[6] 8，N，2（MODBUS,RTU）
[7] 8，E，1（MODBUS,RTU）
[8] 8，O，1（MODBUS,RTU）
Pn700.2 Communication protocol
selection
[0] SCI communication with no
protocol
[1] MODBUS SCI communication
Pn700.3 Reserved
Axis address of MODBUS protocol
Pn701 Axis address After restart ALL
communication
- 147 -
6.3 MODBUS Communication Protocol
MODBUS communication protocol is only used when Pn700.2 is set to 1. There are two modes for MODBUS
communication: ASCII (American Standard Code for information interchange) mode and RTU (Remote Terminal Unit)
mode.
The next section describes the two communication modes.
6.3.1 Code Meaning
ASCII Mode：
Every 8-bit data is consisted by two ASCII characters. For example: One 1-byte data 64 H（Hexadecimal expression）is
expressed as ASCII code ‘64’, which contains ‘6’ as ASCII code 36H and ‘4’ as ASCII code 34H.
ASCII code for number 0 to 9、character A to F are as follows:

Character ‘0’ ‘1’ ‘2’ ‘3’ ‘4’ ‘5’ ‘6’ ‘7’
ASCII Code 30 H 31 H 32 H 33 H 34 H 35 H 36 H 37 H
Character ‘8’ ‘9’ ‘A’ ‘B’ ‘C’ ‘D’ ‘E’ ‘F’
ASCII Code 38 H 39 H 41 H 42 H 43 H 44 H 45 H 46 H
RTU Mode：
Every 8-bit data is consisted by two 4-bit hexadecimal data, that is to say, a normal hexadecimal data. For example:
decimal data 100 can be expressed as 64H by 1-byte RTU data.
Data Structure：
10-bit character form（7-bit data）
- 148 -
11-bit character form（8-bit data）
Communication protocol structure：

Data format of communication protocol：
ASCII Mode：
STX Start character‘：’＝＞(3A H)
ADR Communication address＝＞1-byte contains two ASCII codes
CMD Reference code＝＞1-byte contains two ASCII codes
DATA(n-1) Data content＝＞n-word=2n-byte contain 4n ASCII codes，n≦12
……
DATA(0)
LRC Checking code＝＞1-byte contains two ASCII codes
End 1 End code 1＝＞（0D H）（CR）
End 0 End code 0＝＞（0A H）（LF）
RTU Mode：
STX Sleep interval of at least 4 bytes transmission time.
ADR Communication address＝＞1-byte
CMD Reference code＝＞1-byte
DATA(n-1) Data content＝＞n-word=2n-byte，n≦12
……
DATA(0)
CRC CRC checking code＝＞1-byte
End 1 Sleep interval of at least 4 bytes transmission time.
Communication protocol data format instructions are as follows：

STX（communication start）
ASCII mode：‘: ’character
- 149 -
RTU mode: Sleep interval of at least 4 bytes transmission time (automatically changed according to different
communication speed).
ADR（communication address）
Valid communication address：1 to 254
For example: communicate with the servo drive which address is 32（20 in hex）：
ASCII mode：ADR=‘2’，‘0’=＞‘2’=32H，‘0’=30H
RTU mode：ADR=20H
CMD（command reference）and DATA（data）
Data structure is determined by command code. Regular command code is shown as follows:
Command code: 03H，read N words(word)，N ≦ 20.
For example: read 2 words starting from 0200 H from the servo drive which address is 01 H.
ASCII mode：
Reference information： Response information：
STX “：”
‘0’ STX “：”
ADR ‘0’
‘1’ ADR
‘0’ ‘1’
CMD ‘0’
‘3’ CMD
‘0’ ‘3’
‘2’ Data number ‘0’

Data start address （count as byte） ‘4’
‘0’
‘0’ ‘0’
‘0’ Content of data start ‘0’

address 0200H ‘B’
Data number ‘0’
‘1’
(count as word） ‘0’
‘1’
‘2’
Content of second data ‘F’
‘F’
LRC checking address 0201 H ‘4’
‘8’
‘0’
End 1 (0D H)(CR)
‘E’
End 0 (0A H)(LF) LRC checking
‘8’
End 1 (0D H )(CR)
End 0 (0A H )(LF)
RTU mode：
Reference information：： Response information：
ADR 01 H ADR 01 H
CMD 03 H CMD 03 H
02 H (high-bit) Data number
Data start address 04 H
00 H (low-bit) （count as byte）
Data number 00 H Content of data start 00 H (high-bit)
（count as word） 02 H address 0200H B1 H (low-bit)
CRC checking C5 H (low-bit) Content of second data 1F H (high-bit)
CRC checking B3 H (high-bit) address 0201 H 40 H (low-bit)
CRC checking A3 H (low-bit)
CRC checking D3 H (high-bit)
Reference code: 06H，write in one word

For example: write 100（0064 H）into 01H servo address 0200 H .
- 150 -
ASCII mode：
STX “：” STX “：”
‘0’ ‘0’
ADR ADR
‘1’ ‘1’
‘0’ ‘0’
CMD CMD
‘6’ ‘6’
‘0’ ‘0’
‘2’ ‘2’
Data start address Data start address
‘0’ ‘0’
‘0’ ‘0’
‘0’ ‘0’
‘0’ Content of data start ‘0’
Data content
‘6’ address 0200H ‘6’
‘4’ ‘4’
‘9’ ‘9’
LRC checking LRC checking
‘3’ ‘3’
End 1 (0D H)(CR) End 1 (0D H )(CR)
End 0 (0A H)(LF) End 0 (0A H )(LF)
RTU mode：
ADR 01 H ADR 01 H
CMD 06 H CMD 06 H
02 H (high-bit) 02 H (high-bit)
Data start address Data start address
00 H (low-bit) 00 H (low-bit)
00 H (high-bit) 00 H (high-bit)
Data content Data content
64 H (low-bit) 64 H (low-bit)
CRC checking 89 H (low-bit) CRC checking 89 H (low-bit)
CRC checking 99 H (high-bit) CRC checking 99 H (high-bit)
LRC（ASCII mode）and CRC（RTU mode）error detection value calculation：

LRC calculation in ASCII mode:
ASCII mode uses LRC (Longitudinal Redundancy Check) error detection value. The exceeded parts (e.g. the total value is
128H of hex, then take 28H only) is taken off by the unit of 256 in the total value from ADR to the last information, then
calculate and compensate, the final result is LRC error detection value.
- 151 -
For example: read 1 word from 01H servo address 0201H

STX ‘：’
‘0’
ADR
‘1’
‘0’
CMD
‘3’
‘0’
‘2’
Data start address
‘0’
‘1’
‘0’
Data number ‘0’
（count as word） ‘0’
‘1’
‘F’
LRC checking
‘8’
End 1 (0D H)(CR)
End 0 (0A H)(LF)
Add from ADR data to the last data.
01 H +03 H +02 H +01 H +00 H +01 H =08 H

The compensate value is F8H when 2 is used to compensate 08H, so LRC is “F”,”8”.
CRC calculation of RTU mode:

RTU mode uses CRC (Cyclical Redundancy Check) error detection value.
The process of CRC error detection value calculation is shown as follows:
Step 1: Load in a 16-bit register of FFFFH, named “CRC” register.

Step 2: Run XOR calculation between the first bit (bit 0) of instruction information and 16-bit CRC register’s low bit (LSB),
and the result is saved to CRC register.
Step 3: Check the lowest bit (LSB) of CRC register, if it is 0, CRC register moves one bit to right; if it is 1, CRC register
moves one bit to right, then run XOR calculation with A001H;
Step 4: Go to step 5 till the third step has been executed for 8 times, otherwise return to step 3.
Step 5: Repeat the steps from 2 to 4 for the next bit of instruction information, the comment of CRC register is the CRC
error detection value while all the bits have been executed by the same way.
Note: After calculating out the CRC error detection value, the CRC low bit should be filled first in instruction information,
and then fill the high bit of CRC.
Please refer to the following example:
Read 2 words from the 0101H address of 01H servo. The final CRC register content calculated from ADR to the last bit of
data is 3794H, and then the instruction information is shown as follows,
Please be sure that 94H is transmitted before 37H.
ADR 01 H
CMD 03 H
01H (high-bit)
Data start address
01H (low-bit)
Data number 00 H (high-bit)
（count as word） 02H (low-bit)
CRC checking 94H (low-bit)
CRC checking 37H (high-bit)
End1、End0（Communication is complete.）
- 152 -
ASCII mode：
Communication is ended with (0DH) - [carriage return] and (0AH) - [new line].
RTU mode：
When the time exceeds the sleep interval by at least 4 bytes transmission time while in the current communication speed,
it means the communication is finished.
Example：
The following example uses C language to generate CRC value. The function needs two parameters.
unsigned char * data;
unsigned char length;
The function will return unsigned integer type CRC value.
unsigned int crc_chk(unsigned char * data,unsigned char length){

int i,j;
unsigned int crc_reg=oxFFFF;
While(length- -){
crc_ reg ^=*data++;
for(j=0;j<8;j++){
If(crc_reg & 0x01){
crc_reg=( crc_reg >>1)^0xA001;
}else{
crc_reg＝crc_reg >>1;
}
}
}
return crc_reg;
}
- 153 -
6.3.2 Communication Error Disposal
Problems that occur during communication are a result of the following:

 Data address is incorrect while reading/writing parameters.
 The data is not within the parameter setting range while writing.
 Data transmission fault or checking code fault when communication is disturbed.
When the first and second communication faults occur, the servo drive is running normally, and will feed back an error
frame.
When the third communication fault occurs, transmission data will be recognized as invalid to give up, and no error frame
is returned.
The format of error frame：
Host controller data frame：

start Slave station address Command Data address,content Checking
command
Servo drive feeds back error frame:

start Slave station address Response code Error code Checking
command＋80 H
Error frame responses code=command+80H

Error code＝00H：Normal communication
＝01H：Servo drive cannot identify the required functions
＝02H: The required data address does not exist in the servo drive
＝03H：The required data in servo drive is not allowed. (Beyond the maximum or minimum
value of the parameter)
＝04H：Servo drive starts to perform the requirement, but cannot achieve it.
For example: Servo drive axis number is 03H，write data 06H into parameter Pn100 is not allowed , because the range of
parameter Pn100 is 0~6. The servo drive will feedback an error frame, the error code is 03H (Beyond the parameter’s
maximum value or minimum value).
Host controller data frame：
start Slave station address Command Data address,content Checking
03H 06H 0002H 0006H
Servo drive feedback error frame：

start Slave station address Response code Error code Checking
03H 86H 03H
Besides, if the data frame sent from host controller slave station address is 00H, it determines the data to be broadcast
data. The servo drives will not feed back any frames.
- 154 -
6.3.3 Data Communication Address of Servo State
The communication parameter addresses are shown in the following table:
Communication
data address Meaning Description Operation
Hex
Parameter area Corresponding parameters in Read/write
0000 ~ 02FD
parameter list
07F1 ~07FA Alarm information memory area Ten alarms historical record Read only
07FB Speed reference zero offset Read/write

07FC Torque reference zero offset Read/write
07FD Iu zero offset Read only
07FE Iv zero offset Read only
Monitor data (corresponding with

0806 ~ 0816
displayed data)
0806 Speed feedback Unit:rpm Read only
0807 Input speed reference value Unit:rpm Read only
Input torque reference percentage Relative rated Read only
0808
torque
Internal torque reference Relative rated Read only
0809
percentage torque
080A Number of encoder rotation pulses Read only
080B Input signal state Read only
080C Encoder signal state Read only
080D Output signal state Read only
080E Pulse setting Read only
080F Low bits of present location Unit:1 reference pulse Read only
High bits of present location Unit:10000 Read only
0810
reference pulses
0811 Error pulse counter low 16 bits Read only
0812 Error pulse counter high 16 bits Read only
0813 Setting pulse counter low bits Unit:1 reference pulse Read only
0814 Setting pulse counter high bits Unit:10000 reference pulses Read only
0815 Load inertia percentage % Read only
0816 Servomotor overloading proportion % Read only
0817 Current alarm Read only
0818 Servomotor winding temperature ℃ Read only
MODBUS communication IO signal Do not save when Read/write

0900
power off.
090E DSP version Version is expressed by digit. Read only
090F CPLD version Version is expressed by digit. Read only
- 155 -
Communication
data address Meaning Description Operation
Hex
17-bit encoder multi-turn Unit:1 revolution Read only.
1010
information Only for 17-bit
Unit:1 pulse Encoder.
17-bit encoder single-turn
1011 Multi-turn:16 bits
information
Single-turn:17 bits
17-bit encoder single-turn
1012
information high bits
1021 Clear historical alarms 01:Clear Write only
1022 Clear current alarms 01:Clear Write only
01:Enable
1023 JOG servo enabled Write only
00:Disable
01:Forward rotation
1024 JOG forward rotation Write only
00:Stop
01:Reverse rotation
1025 JOG reverse rotation Write only
00:Stop
JOG forward rotation at node 01:Forward rotation
1026
position( start signal has been set) 00:Stop
JOG reverse rotation at node 01:Reverse rotation
1027
position(start signal has been set) 00:Stop
01:Pause
1028 Pause at node position
00:Cancel pause
1040 Clear encoder alarm 01:Clear Write only

1041 Clear encoder multi-turn data 01:Clear Only 17-bit encoder
1070 Position teaching function 01:Start Write only
Note:
1. Parameter area（communication address 0000～00DEH）
Parameter address is relevant to the parameters in the parameter list.
For example, parameter Pn000 is relevant to communication address 0000H; parameter Pn101 is relevant to
communication address 0065H. Read/write operation to address 0000H is the read/write operation to Pn000. If the
communication input data is not within the parameter range, the data will be aborted, and servo drive will return an
operation unsuccessful signal.
2. Alarm information storage area（07F1～07FAH）

Historical alarm number Description Communication address
Historical alarm 1 07F1H
0
（the latest alarm）
1~8 Historical alarm 2 ~ 9 07F2H ~ 07F9H
9 Historical alarm 10（the furthest alarm） 07FAH
3. Monitor data area（0806～0816H）

The monitor data is corresponding to servo drive panel displays Un000~Un016.
For example: the corresponding data of communication address 0807H (speed setting) is FB16H.
- 156 -
Therefore, the speed setting is -1258r/m.
4. MODBUS communication IO signal

Use communication to control digital IO signal. This data will not be saved after power off.
It is operated with Pn512 and Pn513 as the communication input IO signal. That is to say, when the parameters setting in
Pn512 and Pn513 enable the IO bit, the IO can be controlled by communication.
5. Software version（090FH）
Use digit to represent servo drive software version. For example, if the read out data is D201H，it means the software
version is D-2.01.
- 157 -
Chapter 7
Specifications and Characters
7.1 Servo drive Specifications and Models
Servo drive Model： ProNet- 02A 04A 08A 10A 15A 20A 30A 50A 10D 15D 20D 30D 50D 70D 75D 1AD 1ED 2BD 02B 04B 08B
Servo drive Model： ProNet-E- 02A 04A 08A 10A 15A 20A 30A 50A 10D 15D 20D 30D 50D — — — — — 02B 04B 08B
EMJ- 02A 04A 08A 10A — — — — — — — — — — — — — — 02B 04B 08B
Applicable Servomotor EMG- — — — 10A 15A 20A 30A 50A 10D 15D 20D 30D — — — — — — — — —
Model： EML- — — — 10A — 20A 30A 40A 10D — 20D 30D 40D — — — — — — — —
EMB- — — — — — — — — — — — — 75D — 75D 1AD 1ED 2BD — — —
Continuous Output Current[Arms] 1.4 2.8 4.0 6.0 9.0 12.0 18.0 28.0 3.2 5.0 6.4 9.0 15.0 18.0 18.0 28.0 38.0 55.0 2.7 5.8 8.2
Max. Output Current [Arms] 4.2 8.4 12.0 18.0 28.0 42.0 45.0 62.0 9.6 15.0 19.2 27.0 45.0 48.0 48.0 65.0 100.0 128.0 8.1 15.1 24.6
Main Input Power Supply Capacity [kVA] 0.5 0.9 1.3 1.8 2.5 3.5 4.5 7.5 1.8 2.8 3.5 5.0 8.2 12.0 12.0 18.0 22.0 32.0 0.5 0.9 1.3
DC24V Power Supply Capacity [W] — — — — — — — — 30.0 30.0 30.0 45.0 45.0 45.0 45.0 — — — — — —
Single-
Three-phase
phase 200 ～ Three-phase Three-phase
380～440VAC Single-phase 100～120VAC
Main Circuit 200～230VAC 380～480VAC
230VAC +10%～ +10%～ +10%～-15% (50/60Hz)
+10%～-15% (50/60Hz) +10%～-15%(50/60Hz)
-15% (50/60Hz) -15%(50/60Hz)
Input Power Supply
Single-phase
Single-phase
24VDC 380～440VAC Single-phase 100～120VAC
Control Circuit 200～230VAC
+10%～-15% +10%～ +10%～-15% (50/60Hz)
+10%～-15% (50/60Hz)
-15%(50/60Hz)
Control Method SVPWM Control
Feedback Serial Encoder：131072P/R
- 158 -
Resolver：65536P/R（Max.）
Incremental Wire-saving type:2500 P/R
Ambient temperature：-20～+55℃
Ambient/Storage Temperature
Storage temperature：-25～+55℃
Operating Ambient/Storage Humidity 5%～95% RH (with no condensation)
Conditions Elevation 1000m or less
Vibration/ShockResistance Vibration Resistance：4.9m/s2，Impact Resistance：19.6m/s2
Electric Power System TN system *3
Configuration Base-mounted
Speed Control Range 1:5000
Load
0～100% load：±0.01% or less（at rated speed）
Regulation
Performance Speed Voltage
Rated voltage ±10%：0%（at rated speed）
Regulation Regulation
Temperature
25±25℃：±0.1% or less（at rated speed）
Regulation
Reference ±10VDC at rated torque（Variable setting range:±0～10VDC）
Analog Voltage Max. input voltage：±12V
Torque Input
Reference About 10MΩ or above
Control Impedance
Input
Circuit Time
10μs
Constant
Reference ±10VDC at rated speed（Variable setting range:±0～10VDC）
Voltage Max. input voltage：±12V
Analog Input Input
About 10MΩ or above
Reference Impedance
Circuit Time
10μs
Constant
Speed
Rotation
Control
Speed Direction With /P-CON signal
Selection
Selection
Speed
Speed 1 to 7
Selection
Soft
Function 0～10s（Can be set individually for acceleration and deceleration.）
Start
- 159 -
Setting
Sign + pulse train;CCW + CW pulse train;
Type
90°phase difference 2-phase (phase A + phase B)
Form Non-insulated linde driver (about + 5V), open collector
Pulse ×1 multiplier：4Mpps
Reference ×2 multiplier：2Mpps
Position
Frequency ×4 multiplier：1Mpps
Control
Open collector：200Kpps
Frequency will begin to decline when the duty ratio error occurs..
Position
Position
Reference 16 postion nodes can be set.
Setting
Setting
Encoder Dividing Pulses Phase-A, phase-B, phase-C, line driver output
Output Number of dividing pulses：any
Number of
8 channels
Sequence channels
Signal allocations and positive/negative logic modifications:
Input
Function Servo ON（/S-ON），P control（/P-CON），alarm reset（/ALM-RST），position error clear（/CLR），forward run prohibited（P-OT），reverse run prohibited（N-OT），forward current
limit（/P-CL），reverse current limit（/N-CL） and so on.
Number of
4 channels
Sequence channels
I/O Signals
Signal allocations and positive/negative logic modifications:
Output
Function Positioning completion(/COIN), speed coincidence(/V-CMP),servomotor rotation detection(/TGON), servo ready(/S-RDY),torque limit output(/CLT), brake interlock output (/BK),
encoder C pulse(/PGC) and Over travel （/OT）.
Regenerative Functions 0.75kW～7.5kW：internal regenerative resistor；11kW～22kW：external regenerative resistor
Protection Functions Overcurrent, overvoltage,low voltage, overload,regeneration error,overspeed,etc.
Utility Function Alarm trace back、JOG operation、load inertia detection, etc.
Display Function CHARGE（Red）、POWER（Green）、five 7-segment LEDS (Built-in panel operator)
RS-485 communication port,MODBUS protocol ;CAN communication port,CANopen protocol;
Communication Functiion
EtherCAT communication module,CiA402 protocol;POWERLINK communication module,CiA402 protocol
- 160 -
7.2 Servo drive Dimensional Drawings
 ProNet-02/04A
ProNet-E-02/04A
Unit:mm
Nameplate
Note：ProNet-E does not support extended module.
 ProNet-04B/08A/10A
ProNet-E-04B/08A/10A
Unit: mm
Nameplate
Air Flow (32)
Extended Module
D P 100
13.8
10
0°
ADDL ADDH
CHARGE POWER
CN3
COMM
L1
L2
CN4
CN5
L3
1
2
Air Flow
L1C
CN1
L2C
B1
B2
B3
U
V
W
CN2
Air Flow
Cooling Fan
Mounting Hole Diagram
Air Flow
- 161 -
 ProNet-08B/10D/15A/15D/20A/20D
ProNet-E-08B/10D/15A/15D/20A/20D
Unit:mm
94.4 (32)
Air Flow Extended Module Nameplate
SERVODRIVE 200V
PRONET-10A
D P 1 00
13.8
10
0°
ADDL ADDH
96
CHARGE POWER
务必在阅读使用说明书后，按其步骤操作。 Read manual carefully and follow the direction.

ALM
CN3
COMM
WARNING May cause electric shock.

CAUTION Do not touch heatsink. May cause burn.
Use proper grounding techniques.
接地端子必须接地。
注意
危险
L1
L2
CN4
Disconnect all power and wait 5 minutes before servicing.
通电时请勿触摸散热片！有烫伤的危险。
切断电源５分钟内，请勿触摸驱动器端子和配线！有触电的危险。
CN5
L3
1
186
2
Air Flow
L1C
CN1
L2C
B1
B2
B3
Three Terminals
U
V
W
CN2
Cooling Fan 4.8
Air Flow Ground Terminal
5.5
2-M4 Screw
Mounting Hole Diagram 4-M4 Screw Holes (75)
100 24 180
(Mounting Pitch)
Figure
186
175
Air Flow
5.5 89
100
 ProNet-30A/30D/50A/50D/70D
ProNet-E-30A/30D/50A/50D
Unit:mm
(32) Nameplate
6
Mounting Hole Diagram 4-M5 Screw Holes Air Flow Extended Module
SERVODRIVE 200V
PRONET-50A
13.8
D P 10 0
10
0°
ADDL ADDH
CHARGE POWER
ALM
CN3
COMM
CN4
CN5
务必在阅读使用说明书后，按其步骤操作。 Read manual carefully and follow the direction.
WARNING May cause electric shock.
CAUTION Do not touch heatsink. May cause burn.
Use proper grounding techniques.
接地端子必须接地。
注意
危险
(Mounting Pitch)
CN1
Disconnect all power and wait 5 minutes before servicing.
通电时请勿触摸散热片！有烫伤的危险。
切断电源５分钟内，请勿触摸驱动器端子和配线！有触电的危险。
Figure
270.5
258.5
270.5
CN2
Terminal
(14-M4 Screw)
5.5
6 112
(Mounting Pitch) Ground Terminal
Air Flow 2-M4 Screw
125 125 24 (75) 204.5
10
5°
(38)
Cooling Fan
- 162 -
 ProNet-75D/1AD/1ED/2BD
Unit:mm
Air Flow Air Flow
Air Flow
- 163 -
Appendix A
Parameter
A.1 Parameter List

Name Unit
Binary
Pn000.0：Servo ON
Pn000.1：Forward rotation input signal
prohibited（P-OT）
Pn000.2：Reverse rotation input signal
prohibited（N-OT）
Pn000.3：Alarm output when
instantaneous power loss
Binary
Pn001.0：CCW,CW selection
Pn001 Pn001.1：Analog speed limit enabled — 0~1111 0 After restart
Pn001.2：Analog torque limit enabled
Pn001.3：2nd electronic gear enabled
Binary
Pn002.0：Electronic gear switching mode
Pn002 Pn002.1：Reserved — 0~0111 0010 After restart
Pn002.2：Absolute encoder selection
Pn002.3：Reserved
Binary
Pn003.0: Reserved
Pn003.2：Low speed compensation
Pn003.3：Overload enhancement
Hex
Pn004.0: Stop mode
Pn004 Pn004.1: Error counter clear mode — 0~0x3425 0 After restart
Pn004.2: Reference pulse form
Pn004.3: Inverses pulse
- 164 -

Name Unit
Hex
Pn005.0: Torque feedforward mode
Pn005.1: Control mode
[0] Speed control (analog reference)
[1] Position control (pulse train)
[2] Torque control (analog reference)
[3]Speedcontrol (contact reference)←→
speed control (zero reference)
[4] Speed control (contact reference)←→
speed control (analog reference)
position control (pulse train)
torque control (analog reference)
Pn005 [7] Position control (pulse train)←→ — 0~0x33E3 0 After restart
[8] Position control (pulse train)←→
torque control (analog reference)
[9] Torque control (analog reference)←→
[A] Speed control (analog reference)←→
zero clamp
[B] Position control (pulse train)←→
position control (inhibit)
[C] Position control (contact reference)
[D] Speed control (parameter reference)
[E] Special control
Pn005.2: Out-of-tolerance alarm selection
Pn005.3: Servomotor model
Hex
Pn006.0: Bus mode
Pn006.1: Reserved
Pn006 Pn006.2: Low frequency jitter suppersion — 0~0x2133 0x0020 After restart
switch
Pn006.3: Reference input filter for open
collector signal
Binary
Pn007.0： wider the width of C pulse or not
Pn007.2：Reserved
Pn007.3：Reserved
Online autotuning setting
Pn100 0:Manual gain adjustment — 0~6 1 After restart
1,2,3=Normal mode;4,5,6=Vertical load
- 165 -

Name Unit
1,4 = Load inertia without variation;
2,5 = Load inertia with little variation;
3,6= Load inertia with great variation
Pn101 Machine rigidity setting — 0~15 5 Immediately
Pn102 Speed loop gain Hz 1~4000 160 Immediately
Pn103 Speed loop integral time constant 0.1ms 1~4096 200 Immediately
Pn104 Position loop gain 1/s 0~1000 40 Immediately
Pn105 Torque reference filter time constant 0.1ms 0~250 4 Immediately
Pn106 Load inertia percentage — 0~20000 0 Immediately
Pn107 2nd speed loop gain Hz 1~4000 40 Immediately
Pn108 2nd speed loop integral time constant 0.1ms 1~4096 200 Immediately
Pn109 2nd position loop gain Hz 0~1000 40 Immediately
Pn110 2nd torque reference filter time constant 0.1ms 0~250 4 Immediately
Pn111 Speed bias rpm 0~300 0 Immediately
Pn112 Feedforward % 0~100 0 Immediately
Pn113 Feedforward filter 0.1ms 0~640 0 Immediately
Pn114 Torque feedforward % 0~100 0 Immediately
Pn115 Torque feedforward filter 0.1ms 0~640 0 Immediately
P/PI switching condition
0: Torque reference percentage
1: Value of offset counter
2: Value of acceleration speed setting
3: Value of speed setting
4: Fixed PI
Pn117 Torque switching threshold % 0~300 200 Immediately
reference
Pn118 Offset counter switching threshold 0~10000 0 Immediately
pulse
Setting acceleration speed switching
Pn119 10rpm/s 0~3000 0 Immediately
threshold
Pn120 Setting speed switching threshold rpm 0~10000 0 Immediately
Gain switching condition
0: Fix to 1st group gain
1: External switch gain switching
2: Torque percentage
Pn121 3: Value of offset counter — 0~6 0 After start
4: Value of acceleration speed setting
6: Speed reference input
7: actual motor speed
Pn122 Switching delay time 0.1ms 0~20000 0 Immediately
Pn123 Threshold switching level 0~20000 0 Immediately
Pn124 Reserved — — — —
Pn125 Position gain switching time 0.1ms 0~20000 0 Immediately
- 166 -

Name Unit
Pn126 Hysteresis switching — 0~20000 0 Immediately
Pn127 Low speed detection filter 0.1ms 0~100 10 Immediately
Speed gain acceleration relationship Immediately
Pn128 — 0~3 3
during online autotuning
Pn129 Low speed correction coefficient — 0~30000 0 Immediately
Pn130 Friction load 0.1% 0~3000 0 Immediately
Friction compensation speed hysteresis Immediately
Pn131 rpm 0~100 0
area
0.1%/1000rp Immediately
Pn132 Sticking friction load 0~1000 0
m
Pn200 PG divided ratio Puls 16~16384 16384 After restart
Pn201 1st electronic gear numerator — 1~65535 1 After restart
Pn202 Electronic gear denominator — 1~65535 1 After restart
Pn203 2nd electronic gear numerator — 1~65535 1 After restart
Position reference Acceleration
Pn204 0.1ms 0~32767 0 Immediately
/deceleration time constant
Pn205 Position reference filter form selection — 0~1 0 After restart
Pn300 Speed reference input gain rpm/v 0~3000 150 Immediately
Pn301 Analog speed given zero bias 10mv -1000~1000 0 Immediately
Pn304 Parameter speed rpm -6000~6000 500 Immediately
Pn305 JOG speed rpm 0~6000 500 Immediately
Pn306 Soft start acceleration time ms 0~10000 0 Immediately
Pn307 Soft start deceleration time ms 0~10000 0 Immediately
Pn308 Speed filter time constant ms 0~10000 0 Immediately
Pn309 S curve risetime ms 0~10000 0 Immediately
Speed reference curve form
0:Slope
1:S curve
2:1st order filter
- 167 -

Name Unit
3:2nd order filter
Pn311 S form selection — 0~3 0 Immediately
Pn312 DP communication JOG speed rpm -6000~6000 500 Immediately
Pn316 Internal speed 1 rpm -6000~6000 100 Immediately
Pn319 Internal speed 4 rpm -6000~6000 -100 Immediately
Pn400 Torque reference gain 0.1V/100% 10~100 33 Immediately
Pn401 Forward torque internal limit○
1 % 0~300 300 Immediately
Pn402 Reverse torque internal limit○
Pn403 Forward external torque limit○
Pn404 Reverse external torque limit○
Pn405 Plug braking torque limit % 0~300 300 Immediately
Pn406 Speed limit during torque control rpm 0~6000 1500 Immediately
Pn407 Notch filter 1 frequency Hz 50~5000 5000 Immediately
Pn408 Notch filter 1 depth — 0~11 1 Immediately
Pn409 Notch filter 2 frequency Hz 50~5000 5000 Immediately
Pn410 Notch filter 2 depth — 0~11 1 Immediately
Pn411 Low frequency jitter frequency 0.1Hz 50~500 100 Immediately
Pn412 Low frequency jitter damp — 0~200 25 Immediately
Pn413 Torque control delay time 0.1ms 1~2000 100 Immediately
Pn414 Torque control speed hysteresis rpm 10~1000 50 Immediately
Pn415 Analog torque given zero bias 10mv -1000~1000 0 Immediately
Pn500 Positioning error Puls 0~5000 10 Immediately
Pn501 Coincidence difference rpm 0~100 10 Immediately
Pn502 Zero clamp speed rpm 0~3000 10 Immediately
Pn503 Rotation detection speed TGON rpm 0~3000 20 Immediately
Pn504 Offset counter overflow alarm 256Puls 1~32767 1024 Immediately
Pn505 Servo ON waiting time ms -2000~2000 0 Immediately
Pn506 Basic waiting flow 10ms 0~500 0 Immediately
Pn507 Brake waiting speed rpm 10~100 100 Immediately
Pn508 Brake waiting time 10ms 10~100 50 Immediately
Pn509 Allocate input signal to terminal — 0~0xFFFF 0x3210 After restart
Pn510 Allocate input signal to terminal — 0~0xFFFF 0x7654 After restart
Pn511 Allocate output signal to terminal — 0~0x0999 0x0210 After restart
Pn512 Bus control input node low-bit enable — 0~1111 0 Immediately
Pn513 Bus control input node low-bit enable — 0~1111 0 Immediately
- 168 -

Name Unit
Pn514 Input port filter 0.2ms 0~1000 1 Immediately
Pn515 Alarm port filter 0.2ms 0~3 1 Immediately
Pn516 Input port signal inversion — 0~1111 0 Immediately
Pn517 Input port signal inversion — 0~1111 0 Immediately
Pn518 Dynamic brake time 0.5ms 50~2000 125 Immediately
Pn519 Serial encoder error time 0.1ms 0~10000 3 Immediately
Pn520 Position complete time 0.1ms 0~60000 500 Immediately
If connect externally regenerative resistor
0：connect externally regenerative resistor
between B1 and B2
1：dose not connect externally
Pn521 — 0~1 1 Immediately
regenerative resistor, relay on internal
capacitance
（This parameter is in effect only on
ProNet-02/04 /ProNet-E-02/04）
Pn525 Overload alarm threshold % 100~150 100 Immediately
Temperature threshold of motor overheat
Pn526 alarm ℃ 50~180 110 Immediately
（Only enabled in ProNet–75/1A/1E/2B）
Pn528 Output signal inverse — 0~1111 0 Immediately
Torque detection output signal threshold
Pn529 % 3~300 100 Immediately
value
Pn530 Torque detection output signal time ms 1~1000 10 After restart
Pn600 Position pulse in point to point control 10000P -9999~9999 0 Immediately
……
Pn632 Point to point speed control rpm 0~3000 500 Immediately
……
Pn647 Point to point speed control rpm 0~3000 500 Immediately
Pn648 Point to point 1st order filter 0.1ms 0~32767 0 Immediately
……
Pn663 Point to point 1st order filter 0.1ms 0~32767 0 Immediately
Pn664 Stop time 50ms 0~300 10 Immediately
……
Pn679 Stop time 50ms 0~300 10 Immediately
Hex
Pn681 — 0~0x0133 0x0000 Immediately
Pn681.0:Single/cyclic, start/reference point
- 169 -

Name Unit
selection
Pn681.1:Change step and start mode
Pn681.2:Change step input signal mode
Pn681.3:Reserved
Pn682 Programme mode — 0~1 0 Immediately
Pn683 Programme start step — 0~15 0 Immediately
Pn684 Programme stop step — 0~15 1 Immediately
Search travel speed in position control
(contact reference); Speed of finding
Pn685 rpm 0~3000 1500 Immediately
reference point (hitting the origin signal
ORG) in position homing control.
Leave travel switch speed in position
control(contact reference);
Pn686 Speed of finding reference point (leaving rpm 0~200 30 Immediately
the origin signal ORG) in position homing
control.
Pn687 Position teaching pulse 10000P -9999~9999 0 Immediately
Pn688 Position teaching pulse 1P -9999~9999 0 Immediately
Pn689 Homing Mode Setting — 0~0111 0 After restart
Pn690 Number of error pulses during homing 10000pulse 0~9999 0 Immediately
Pn691 Number of error pulses during homing 1pulse 0~9999 0 Immediately
Hex
Pn700.0: MODBUS communication baud
rate
Pn700 Pn700.1: MODBUS protocol selection — 0~0x0182 0x0151 After restart
Pn700.2:Communication protocol
selection
Pn700.3: Reserved
Pn701 MODBUS axis address — 1~247 1 After restart
Pn703 CAN communication speed — 0x0005 0x0004 After restart
Pn704 CAN communication contact — 1~127 1 After restart
Hex
Pn840.0：Encoder model selection
0x0003~
Pn840 Pn840.1：Reserved — — After restart
0x0B06
Pn840.2：Reserved
Pn840.3：Reserved
Note: ○1 The setting range and factory setting of Pn401 to Pn405 depend on the actual overload
capacity.
- 170 -
A.2 Description of Parameter Type
Type Parameter No. Description
Funtion selection switches Pn000~Pn006 Control mode, stop mode, and some functions selection
Parameters of servo gain Pn100~Pn129 Position gain, speed gain,rigidity,etc.
Position control related parameters Pn200~Pn205 PG divided ratio, electronic gear, etc.
Speed control related parameters Pn300~Pn322 Speed reference input, soft start, etc.
Torque control related parameters Pn400~Pn406 Torque limit, etc.
Parameters to control I/O port Pn500~Pn520 Allocation of I/O port function
Point-to-point control and homing control Pn600~Pn686 Internal point-to-point control and homing control related
related parameters parameters
Communication parameters Pn700~Pn701 Setting of communication parameters
- 171 -
A.3 Parameters in detail
Parameter Setting Control

Description Function and Meaning
No. Validation Mode
Pn000.0 Servo ON
[0] External S-ON enabled.
[1] External S-ON disabled. Servo motor excitation
signal is turned ON automatically after S-RDY is
output.
Pn000.1 Forward rotation input signal prohibited
（P-OT）
[0] External P-OT enabled. Operate in the time
sequence setting in Pn004.0 when travel limit occurs.
[1] External P-OT disabled.
Pn000 Binary After restart ALL Pn000.2 Reverse rotation input signal prohibited
(N-OT)
[0]External N-OT enabled. Operate in the time
sequence setting in Pn004.0 when travel limit occurs.
[1] External N-OT disabled.
Pn000.3 Alarm output when instantaneous power
loss
[0]Instantaneous power loss for one period with no
alarm output
[1]Instantaneous power loss for one period with alarm
output
Pn001.0 CCW,CW selection
[0] Sets CCW as forward direction
[1] Sets CW as forward direction
Pn001.1 Analog speed limit enabled
[0] Sets the value of Pn406 as the speed limit value
Pn001.0
during torque control.
ALL
[1] Use the lower speed between V-REF and Pn406
Pn001.1
as an external speed limit input.
T
Pn001 Binary After restart Pn001.2 Analog torque limit enabled
Pn001.2
[0] Sets Pn401~Pn404 as torque limit.
P，S
[1] Sets the value corresponding to Vref input analog
Pn001.3
voltage as torque limit.
P
Pn001.3 2nd electronic gear enabled
[0] Without 2nd electronic gear, PCON signal is used
to switch P/PI
[1] 2nd electronic gear is enabled, PCON signal is only
used as 2nd electronic gear when Pn005.3 is set to 1.
Pn002.0 Electronic gear switching mode
Pn002 Binary After restart ALL [0] Corresponding time sequence
- 172 -

No. Validation Mode
Pn203
Pn201 Electronic gear numerator 2 Pn201
Electronic gear numerator 1 PCON enabled Electronic gear numerator 1
PCON disabled PCON disabled
Reference pulse
t1 t2
t1，t2>1ms
[1] Corresponding time sequence
Time sequence when Pn002.0=0 or 1
Error time sequence
Pn002.1 Reserved
Pn002.2 Absolute encoder selection
[0] Use absolute encoder as an absolute encoder
[1] Use absolute encoder as an incremental encoder
Pn002.3 Reserved
Pn003.0 Reserved
Pn003.1 Reserved
Pn003.2 Low speed compensation
[0] Without low speed correction
[1] With low speed correction to avoid servomotor
creeping, but the degree of correction is
Pn003 Binary After restart ALL determined by the setting in Pn219.
Pn003.3 Overload enhancement
[0] Without overload enhancement function
[1] With overload enhancement function, which can
enhance the overload capacity when servomotor
exceeds the 2 times rated overload. It is used in
frequent power ON/OFF occasions.
- 173 -

No. Validation Mode
Pn004.0 Stop Mode
[0] Stops the servomotor by applying DB and then
releases DB.
[1] Coast to a stop.
[2] Stops the servomotor by DB when servo OFF,
stops the servomotor by plug braking when overtravel,
then places it into coast (power OFF) mode.
[3] Makes the servomotor coast to a stop state when
servo OFF, stops the servomotor by plug braking
when overtravel, then places it into coast (power OFF)
mode.
[4] Stops the servomotor by DB when servo OFF,
stops the servomotor by plug braking when overtravel,
then places it into zero clamp mode.
Pn004.0 [5] Makes the servomotor coast to a stop state when
ALL servo OFF, stops the servomotor by plug braking
Pn004.1 when overtravel, then places it into zero clamp mode.
P Pn004.1 Error counter clear mode
Pn004 Hex After restart
Pn004.2 [0] Clear error pulse when S-OFF, do not when
P overtravel.
Pn004.3 [1] Do not clear error pulse.
P [2] Clear error pulse when S-OFF orovertravel
(excep for zero clamp)
Pn004.2 Reference pulse form
[0] Sign + Pulse
[1] CW+CCW CW + CCW
[2] A + B (×1)
[3] A + B (×2)
[4] A + B (×4)
Pn004.3 Inverses pulse
[0] Do not inverse PULS reference and SIGN reference.
[1] Do not inverse PULS reference; Inverses SIGN
reference.
[2] Inverse PULS reference;Do not inverse SIGN
reference.
[3] Inverse PULS reference and SIGN reference.
Pn005.0 Torque feedforward form
Pn005.0 [0]Use general torque feedforward, external
P，S analog(Tref) feedforward input is invalid.
Pn005.1 [1]Use general torque feedforward, external
ALL analog(Tref) feedforward input is valid.
Pn005.2 [2]Use high-speed torque feedforward, external
P analog(Tref) feedforward input is invalid.
[3]Use high-speed torque feedforward, external
- 174 -

No. Validation Mode
Analog (Tref) feedforward input is valid.
Pn005.1 Control mode
[0]Speed control (analog reference)
PCON：OFF，PI control；ON，P control
[1]Position control (pulse train reference)
PCON：OFF，PI control；ON，P control
[2]Torque control (analog reference)
PCON is invalid.
[3]Speed control (contact reference)←→speed
Control (zero reference)
PCON ， PCL ， NCL ： OFF Switches to position
control(zero reference)
[4]Speed control (contact reference)←→speed
control(analog reference)
control (analog reference)
[5]Speed control (contact reference)←→position
control(pulse train reference)
control(pulse train reference)
[6]Speed control (contact reference)←→torque
Control (analog reference)
control (analog reference)
[7]Position control (pulse train reference)←→speed
PCON：OFF position control (pulse train
reference)；ON speed control (analog reference)
[8]Position control (pulse train reference)←→Torque
PCON：OFF position control (pulse train
reference)；ON torque control (analog reference)
[9]Torque control (analog reference)←→speed
PCON：OFF Torque control (analog reference)；ON
Speed control (analog reference)
[A]Speed control (analog reference)←→zero clamp
Control
PCON：OFF Speed control (analog reference)；ON
zero clamp control
[B]Positin control (pulse train reference)←→position
control (INHIBIT)
PCON：OFF Position control (pulse train
reference)；ON position control (INHIBIT)
- 175 -

No. Validation Mode
[C]Position control (contact reference)
PCON： Used to change step
PCL，NCL：Used to search reference point or start
[D]Speed control (parameter reference)
PCON，PCL，NCL invalid
[E ] Special control
PCON invalid
Pn005.2 Out-of-tolerance alarm selection
[0] Out-of-tolerance alarm disabled
[1] Out-of-tolerance alarm enabled. Outputs alarm
when the value of error counter exceeds Pn504
setting value.
[2] Reserved
[3] Reserved
Pn005.3 Servomotor model selection①
[0] EMJ
[1] EMG
[2] EML
[3] EMB
Pn006.0 Bus type selection
[0] No bus
[1] PROFIBUS-DP V0/V1
[2] PROFIBUS-DP V2
[3] CANopen
Pn006.1 Reserved
Pn006.2 Low-frequency vibration suppression
switch
[0] Low-frequency vibration suppression function
disabled
[1] Low-frequency vibration suppression function
enabled
Pn006.3 Reference input filter for open collector
signal
[0] When pulse is difference input, the max value of
servo receiving pulse frequency○
2 ≤4M

servo receiving pulse frequency○
2 ≤650K

servo receiving pulse frequency ○
2 ≤150K
Pn007.0： wider the width of C pulse or not

[0] standard width of C pulse
Pn007 Binary After restart [1] wider the width of C pulse
Pn007.1：reserved
Pn007.2：reserved
- 176 -

No. Validation Mode
Pn007.3：reserved
[0] Manual gain adjustment

[1,2,3] Normal mode
[4,5,6] Vertical load
[1,4] Load inertia without variation
[2,5] Load inertia with little variation
[3,6] Load inertia with great variation
Note：
1.Autotuning is invalid when servomotor max.speed is
Online autotuning
less than 100rpm. Manual gain adjustment is used.
Pn100 setting After restart P，S
2.Autotuning is invalid when servomotor acceleration
/deceleration speed is less than 5000rpm/s. Manual
gain adjustment is used.
3.Autotuning is invalid when mechanical clearance is
too big during operation. Manual gain adjustment is
used.
4.Autotuning is invalid when the difference of different
speed load is too great. Manual gain adjustment is
used.
The response speed of servo system is determined by
this parameter. Normally, the rigidity should be set a
Machine rigidity little larger. However, if it is too large, it would suffer
Pn101 Immediately P，S
setting mechanical impact. It should be set a little smaller
when large vibration is present. This parameter is only
valid in autotuning.
This parameter determines speed loop gain.
Pn102 Speed loop gain Immediately P，S
Unit: Hz
Decreases the value of this parameter to shorten
Speed loop integral
Pn103 Immediately P，S positioning time and enhance speed response.
time constant
Unit: 0.1ms
This parameter determines position loop gain.
Decreases this value to enhance servo rigidity, but
Pn104 Position loop gain Immediately P
vibration will occur if the value is too large.
Unit: 1/s
Torque reference filter can eliminate or lighten
Torque reference
Pn105 Immediately P，S，T mechanical vibration, but incorrect setting will result to
filter time constant
mechanical vibration. Unit:0.1ms
Load inertia Setting value=(load inertia/rotor inertia)  100
percentage Unit: %
Pn107 2nd speed loop gain Immediately P，S The meanings of these parameters are the same as
2nd speed loop Pn102~Pn105.
integral time constant These parameters are only needed to set when two
- 177 -

No. Validation Mode
2nd position loop types of gain function are enabled.
Pn109 Immediately P
gain
2nd torque reference
Pn110 Immediately P，S，T
filter time constant
This parameter setting can shorten positioning time.
However, if it is too large or does not cooperate with
Pn111 correctly, vibration will occur.
The relationship with speed reference, error counter,
positioning error is shown in the following chart.
Speed reference
Pn111 Speed bias Immediately P

Pn111
Pn500
Error counter
Pn111
Pn500
It is used to set position feedforward. The response

speed is faster and position error is less when this
Pn112 Feedforward Immediately P parameter setting is higher. Vibration will occur if the
value is set too large.
Unit: %
It is used to ease mechanical vibration due to position
feedforward. The feedforward lag will be enlarged and
Pn113 Feedforward filter Immediately P
result to vibration if the value is set too large.
Unit: 0.1ms
It is used to set torque feedforward, and enhance
response speed.
Pn114 Torque feedforward Immediately P，S Set the load inertia percentage(Pn106) correctly to
enable this function in manual gain adjustment mode.
Unit: %
It is used to ease mechanical vibration due to torque
Torque feedforward
Pn115 Immediately P，S feedforward.
filter
Unit: 0.1ms
0: Torque reference percentage
P/PI switching
Pn116 After restart P，S 2: Value of acceleration speed setting
condition
4: Fixed PI
Torque switching Threshold of torque to switch PI control to P control.
Pn117 After restart P，S
threshold Unit: %
- 178 -

No. Validation Mode
Threshold of error counter to switch PI control to P
Offset counter
Pn118 Immediately P control.
switching threshold
Unit: pulse
Setting acceleration Threshold of acceleration speed to switch PI control to
Pn119 speed switching Immediately P，S P control.
threshold Unit: 10rpm/s
Setting speed Threshold of speed to switch PI control to P control.
switching threshold Unit: rpm
0: Fix to 1st group gain
1: External switch gain switching(G-SEL)
2: Torque percentage
Gain switching
Pn121 condition After restart P，S
4: Value of acceleration speed setting（10rpm）
6: Speed reference input
7: actual motor speed
Delay time of switching gain when switching condition
Pn122 Switching delay time Immediately P，S
is satisfied.
Pn123 Switch threshold level Immediately P，S Gain switching trigger level
Pn124 Reserved — — —
Position gain This parameter is used to smooth transition if the
Pn125 Immediately P
switching time change of the two groups of gain is too large.
This parameter is used to set the operation hysteresis
Pn126 Hysteresis switching Immediately P，S
of gain switching.
This parameter is used to filter in low speed detection.
Low speed detection
Pn127 Immediately P，S The speed detection will be lagged if the value is too
filter
large.
Speed gain The increasing multiple of speed loop gain is the same
acceleration rigidity during online autotuning. The speed loop gain
relationship during is larger when this value is higher.
online autotuning
Low speed correction The intensity of anti-friction and anti-creeping at low
coefficient speed. Vibration will occur if this value is set too large.
Pn130 Friction Load Immediately P，S Frictin load or fixed load compensation
Friction
Pn131 compensation speed Immediately P，S Threshold of friction compensation start
hysteresis area
Pn132 Sticking friction load Immediately P，S Sticking damp which is in direct proportion to speed.
- 179 -

No. Validation Mode
Analog encoder output orthogonal difference pulses.
PG divided The meaning of this value is the number of analog
Pn200 After restart P，S，T
ratio encoder output orthogonal difference pulses per one
servomotor rotation.
1st electronic gear The electronic gear enables the reference pulse to
Pn201 After restart P
numerator relate with the servomotor travel distance, so the host
Electronic gear controller doesn't change the mechanical deceleration
denominator ratio and encoder pulses. In fact, it is the setting of
frequency doubling or frequency division to the
2nd electronic gear reference pulses.
numerator Numerator ( Pn201 or Pn203)
Deno min ator ( Pn202)
Position reference
This value is used to smooth the input pulses. The
acceleration
Pn204 Immediately P effect of smoothness is better when the value is
/deceleration time
higher, but lag will occur if the value is too large.
constant
Position reference [0]：1st order filter
filter form selection [1]：2nd order filter
Speed reference
Pn300 Immediately S The corresponding speed to 1V analog input
input gain
This parameter is used to set zero bias of analog
speed given, and it is related with the speed reference
Analog speed given input gain (Pn300).
Pn301 Immediately S
zero bias Speed reference=(External speed given input
analog-Analog speed given zero bias) × Speed
reference input gain
The parameter can be set to positive or negative.
When control mode is set to D, it determines the
Pn304 Parameter speed Immediately S speed of motor .
The servomotor speed is determined by this
parameter when Pn005.1=D.
It is used to set JOG rotation speed, and the direction
Pn305 JOG speed Immediately S is determined by the pressing key during JOG
operation.
Pn306 Soft start acceleration Immediately S The time for trapeziform acceleration to accelerate to 1000rpm.
- 180 -

No. Validation Mode
time Unit: ms
The time for trapeziform deceleration to decelerate to
Soft start
Pn307 Immediately S 1000rpm.
deceleration time
Unit: ms
Speed filter time 1st order filter time constant
Pn308 Immediately S
constant Unit: ms
S curve The time for transition from one point to another point
Pn309 Immediately S
risetime in S curve.
0:Slope
Speed reference
1:S curve
Pn310 curve form After restart S
2:1st order filter
3:2nd order filter
Pn311 S form selection After restart S This value determines the transition form of S curve.
DP communication Communication speed of bus JOG.
JOG speed It can be set to positive or negative.
Pn316 Speed internal 1 Immediately S Internal speed is enabled when Pn005.1=3~6
Pn317 Speed internal 2 Immediately S Input signal operating speed
Pn318 Speed internal 3 Immediately S
/P-CON /P-CL /N-CL
OFF(H) OFF(H) OFF(H) Zero speed or switch
Pn321 Speed internal 6 Immediately S OFF(H) ON(L) SPEED1
ON(L) OFF(H) SPEED2
ON(L) ON(L) SPEED3
Immediately ON(L) OFF(H) OFF(H) SPEED4

Pn322 Speed internal 7 S
OFF(H) ON(L) SPEED5
ON(L) OFF(H) SPEED6
ON(L) ON(L) SPEED7
Torque reference The meaning of this parameter is the needed analog

Pn400 Immediately T
gain input voltage to reach the rated torque.
Forward torque
internal limit
Reverse torque
internal limit
Forward external Servomotor output torque limit value（depending on
torque limit the actual overload capacity）.
Reverse external
torque limit
Plug braking torque
limit
- 181 -

No. Validation Mode
Speed limit during Servomotor output torque limit value during torque
Pn406 Immediately T
torque control control
Notch filter 1 1. In some conditions,
Pn407 Immediately P，S，T Notch filter 1 frequency
frequency vibration will be picked
Pn408 Notch filter 1 depth Immediately P，S，T Notch filter 1 depth up and response will be
Notch filter 2 lagged after notch filter
Pn409 Immediately P，S，T Notch filter 2 frequency
frequency is set.
2. When notch filter
frequency is set to
Pn410 Notch filter 2 depth Immediately P，S，T Notch filter 2 depth
5000, the notch filter is
invalid.
Low frequency
Pn411 Immediately P，S Frequency of low frequency vibration with load.
vibration frequency
Low frequency Attenuation damp of low frequency vibration with load.
vibration damp It does not need to change.
Torque control delay
Pn413 Immediately T
time These parameters are only enabled in position control
Torque control speed mode.
Pn414 Immediately T
hysteresis
This parameter is used to set zero bias of analog
torque given, and it is related with torque reference
Analog torque given input gain (Pn400),
Pn415 Immediately T
zero bias Torque reference=(External torque given input
analog-Analog torque given zero bias) × Torque
reference input gain
Outputs /COIN signal when error counter is less than
Pn500 Positioning error Immediately P
this value.
Outputs /VCMP signal when the difference between
Coincidence
Pn501 Immediately P speed reference value and speed feedback value is
difference
less than this value.
The servomotor is locked in the form of temporary
Pn502 Zero clamp speed Immediately S position loop when the speed corresponding to the
analog input is less than this value.
When the servomotor speed exceeds this parameter
Rotation detection
Pn503 Immediately P，S，T setting value, it means that the servomotor has
speed TGON
already rotated steadily and outputs /TGON signal.
When the value in error counter exceeds this
Offset counter
Pn504 Immediately P parameter setting value, it means that error counter
overflow alarm
alarm has occurred and outputs alarm an signal.
These parameters are only enabled when the port

Servo ON waiting output parameters are allocated with /BK signal
time output.
These parameters are used to keep braking (prevent
- 182 -

No. Validation Mode
from gravity glissade or continuous outside force on
servomotor) time sequence.
Pn506 Basic waiting flow Immediately P，S，T Servo ON waiting time：
1 For the parameter is plus,/BK signal is output firstly
○
when servo-ON signal is input, and then servomotor
excitation signal is created after delaying the
Pn507 Brake waiting speed Immediately P，S，T parameter setting time.

2 For the parameter is minus, servomotor excitation
○
signal is output firstly when servo-ON signal is input,
and then /BK signal is created after delaying the
parameter setting time.
Basic waiting flow:
Standard setting: /BK output (braking action) and
servo-OFF are at the same time.
Now, the machine movable part may shift slightly due
to gravity according to mechanical configuration and
character; it can be eliminated by using the
parameters when the servomotor is at stop or at a low
Pn508 Brake waiting time Immediately P，S，T speed.
Brake waiting speed:
/BK signal is output when the servomotor speed is
decreased below the parameter setting value at
servo-OFF.
Brake waiting time：
BK signal is output when the delay time exceeds the
parameter setting value after servo-OFF.
/BK signal is output as long as either of the brake
waiting speed or brake waiting time is satisfied.
Allocate input port to Pn509.0 corresponding port CN1_14
Pn509 signal, one port with After restart P，S，T Pn509.1 corresponding port CN1_15
four bits(hex) Pn509.2 corresponding port CN1_16
Pn509.3 corresponding port CN1_17
Allocate input port to Terminal PRI ： CN1_14< CN1_15< CN1_16<
Pn510 signal, one port with After restart P，S，T CN1_17< CN1_39< CN1_40< CN1_41< CN1_42
four bits(hex) Corresponding signal of each data is shown as
following：
0：S-ON
1：P-CON
2：P-OT
3：N-OT
- 183 -

No. Validation Mode
4：ALMRST
5：CLR
6：P-CL
7：N-CL
8：G-SEL
9：JDPOS-JOG+
A：JDPOS-JOG-
B：JDPOS-HALT
C：HmRef
D：SHOM
E：ORG
Pn511.0 corresponding port CN1_11，CN1_12
Corresponding signal of each data is shown as
follows:
0：/COIN/VCMP
1：/TGON
Pn511 Output signal
After restart P，S，T 2：/S-RDY
allocation
3：/CLT
4：/BK
5：/PGC
6：OT
7：/RD
8：/HOME
9：/TCR
Bus communication input port enabled:
[0]：Disabled
Bus control input
Pn512 Immediately P，S，T [1]：Enabled
node low-bit enabled
Pn512.0CN1_14
Pn512.1CN1_15
Pn512.2CN1_16
Pn512.3CN1_17
Bus control input Pn513.0CN1_39
node low-bit enabled Pn513.1CN1_40
Pn513.2CN1_41
Pn513.3CN1_42
It is used to set input port filter time. The signal will be
Pn514 Input port filter Immediately P，S，T
lagged if the parameter setting is too high.
- 184 -

No. Validation Mode
[0]：Do not inverse signal.
Input port signal [1]：Inverse signal
Pn516 inversion Immediately P，S，T Pn516.0CN1_14 inversion
Pn516.1CN1_15 inversion
Input port signal Pn517.0CN1_39 inversion
Pn517 inversion Immediately P，S，T Pn517.1CN1_40 inversion
If a regenerative resistor if connected externally
0：connect externally regenerative resistor between B1
and B2
Pn521 Binary Immediately P,S,T 1：Dose not connect externally regenerative resistor,
relay on internal capacitance.
（This parameter is in effect only on ProNet-02/04/
ProNet-E-02/04）
When load percentage is larger than overload alarm
Overload alarm
threshold, A04 will occur soon.
Pn525 threshold Immediately P，S，T
Pn525 is recommended to set below 120, otherwise
the servo drive and motor will be damaged.
Temperature
threshold of motor When servomotor winding temperature exceeds
Pn526 overheat alarm Immediately P，S，T Pn526 setting, A19 will occur. (Only enabled in
(Only enabled in ProNet–75/1A/1E/2B )
ProNet–75/1A/1E/2B)
[0]：Do not inverse signal.
[1]：Inverse signal
Pn528 Output signal inverse Immediately P，S，T Pn528.0CN1_5,6 inversion

Pn528.0CN1_7,8 inversion
Torque detection When motor torque output is higher than Pn529

setting value,/TCR is ON. When motor torque output is
Pn529 output signal Immediately P，S，T
lower than Pn529 setting value,/TCR is OFF.
threshold value
Unit:%
Torque detection
Pn530 After restart P，S，T Torque detection output signal time. Unit:ms
output signal time
- 185 -

No. Validation Mode
JPOS0 Position pulse The two parameters are used in combination, and the
Pn600 in point to point Immediately P algebraic sum of them is the position JPOS0 needs to
control reach. (The number of servomotor rotation revolutions
is related with the programme mode of point to point
JPOS0
control.)
Pn601 Position pulse in Immediately P
Pn600 Unit：10000P
point to point control
Pn601 Unit：1P
The meaning of other point to point control related
……
parameters are the same.
JPOS15 Position The two parameters are used in combination, and the
Pn630 pulse in point to point Immediately P algebraic sum of them is the position of JPOS0 needs
control to reach. (The number of servomotor rotation
JPOS15 Position revolutions is related with the programme mode of
Pn631 pulse in point to point Immediately P point to point control.)
control
JPOS0 Point to point JPOS0 Point to point speed control
Pn632 Immediately P
speed control Unit：rpm
…… The speed of other point to point control
JPOS15 Point to The speed of JPOS15 point to point control
Pn647 Immediately P
point speed control Unit：rpm
JPOS0
1st order filter time of JPOS0 point to point control can
Pn648 Point to point Immediately P
stop or start the servomotor mildly.
1st order filter
…… 1st order filter of other point to point control.
JPOS15 Point to 1st order filter time of JPOS15 point to point control
Pn663 Immediately P
point 1st order filter can stop or start the servomotor mildly.
JPOS0 point to point JPOS0 point to point control stop time
Pn664 Immediately P
control stop time Unit：50ms
…… Other point to point control stop time
JPOS15 point to
JPOS15 point to point control stop time
Pn679 point control stop Immediately P
Unit：50ms
time
Pn681.0 Single/cyclic, start/reference point selection
[0] Cyclic operation, PCL start signal, NCL search
reference point in forward direction.
[1] Single operation, PCL start signal, NCL search
reference point in forward direction.
[2] Cyclic operation, NCL start operation, PCL search
Pn681 Hex Immediately P reference point in forward direction.
[3] Single operation, NCL start operation, PCL
search reference point in forward direction.
Pn681.1 Change step and start mode
[0] Delay to change step, no need of start signal, delay
to start after S-ON.
[1] PCON change step, no need of start signal, PCON
- 186 -

No. Validation Mode
delay to start after S-ON, but inside pulse can not
stop when PCON off.
[2] Delay to change step, need start signal, canceling
start signal can immediately stop inside pulse.
Return to programme start point process step when
reset.
[3] PCON change step, need start signal, canceling
start signal can immediately stop inside pulse. Return
to programme start point process step when reset.
Pn681.2 Change step input signal mode
[0] Change step input signal electrical level mode
[1] Change step input signal pulse mode
Pn681.3 Reserved
[0] ：Incremental programme
Pn682 Programme mode Immediately P
[1] ：Absolute programme
Pn683 Programme start step Immediately P Select the start point of the point to point control
Pn684 Programme stop step Immediately P Select the stop point of the point to point control.
Search travel speed
in position
control (contact
reference);
Speed of finding Search the servomotor speed in the direction of
Pn685 Immediately P
reference point reference point towards travel switch.
(Hitting the
origin signal ORG) in
position homing
control.
Leave travel switch
speed in position
control (contact
reference);
Speed of finding Search the servomotor speed when the reference
Pn686 Immediately P
reference point point leaves travel switch.
(Leaving the
origin signal ORG) in
position homing
control.
Position teaching The two parameters are used in combination, and the
Pn687 Immediately P
pulse algebraic sum of them is the current position of
position teaching. When performing the position
teaching by utility function, the algebraic sum of the
Position teaching
Pn688 Immediately P two parameters are given to the current position
pulse
Pn687 unit：10000P
Pn688 unit：1P
Pn689.0 Homing Mode
Pn689 Homing Mode Setting Immediately P
[0] Homing in the forward direction
- 187 -

No. Validation Mode
[1] Homing in the reverse direction
Pn689.1 Search C-Pulse Mode
[0] Return to search C-Pulse when homing
[1] Directly search C-Pulse when homing
Pn689.2 Homing trigger starting mode
[0] Homing function disabled
[1] Homing triggered by SHOM signal (rising edge)
Pn689.3 Reserved
Number of error unit：10000P
Pn690 Immediately P
pulses during homing
Number of error
Pn691 Immediately P unit：1P
pulses during homing
Pn700.0 MODBUS communication baud rate
[0] 4800bps
[1] 9600bps
[2] 19200bps
Pn700.1 MODBUS protocol selection
Pn700 Hex After restart ALL
[6] 8，N，2（MODBUS,RTU）
[7] 8，E，1（MODBUS,RTU）
[8] 8，O，1（MODBUS,RTU）
Pn700.2 Communication protocol selection
[0] No protocol SCI communication
[1] MODBUS SCI communication
Pn700.3 Reserved
MODBUS Axis
Pn701 After restart ALL Axis address of MODBUS protocol communication
address
Pn703.0 CAN communication baud rate
[0] 50Kbps
[1] 100Kbps
CAN communication
Pn703 After restart ALL [2] 125Kbps
speed
[3] 250Kbps
[4] 500Kbps
[5] 1Mbps
CAN communication
Pn704 After restart ALL CANopen Aix address of communication
contact
Pn840.0 Encoder model selection
[0]-[2] Reserved（For factory using）
Pn840 Hex After restart ALL [3] 17-bit absolute encoder
[4] 17-bit incremental encoder
[5] Resolver
- 188 -

No. Validation Mode
[6] Wire-saving incremental encoder
Pn840.1 Reserved（For factory using）
Note：
①：When connecting to EMJ-04A□H□□ ，Pn005.3 should be set as “1”.
○
2 ：“the max value of servo receiving pulse frequency” ,it means the sufficient max value of pulse
frequency receiving by servo hardware.
- 189 -
Appendix B
Alarm Display
Alarm Alarm
Alarm Name Meaning
Display Output
A．01 ╳ Parameter breakdown The checksum results of parameters are abnormal.
A．02 ╳ AD shift channels breakdown AD related electrical circuit is faulty
The servomotor speed is excessively high and the

A．03 ╳ Overspeed
servomotor is out of control.
The servomotor is operating continuously under a torque
A．04 ╳ Overload
largely exceeding ratings.
A．05 ╳ Position error counter overflow Internal counter overflow
A．06 ╳ Position error pulse overflow Position error pulse exceeded parameter (Pn504)
The setting of electronic gear or

The setting of electronic gear is not reasonable or the
A．07 ╳ given pulse frequency is not
given pulse frequency is too high.
reasonable.
The 1st channel of current
A．08 ╳ Something wrong with the inside chip of the 1st channel.
detection is wrong.
The 2nd channel of current
A．09 ╳ Something wrong with the inside chip of the 2nd channel.
detection is wrong.
At least one of Incremental Encoder PA,PB,PC is broken
A．10 ╳ Incremental Encoder is break off.
off.
A．12 ╳ Overcurrent An overcurrent flowed through the IPM.
Main circuit voltage for servomotor rotation is excessively

A．13 ╳ Overvoltage
high.
Main circuit voltage for servomotor rotation is excessively
A．14 ╳ Undervoltage
low.
A．15 ╳ Bleeder resistor error Bleeder resistor is faulty.
A．16 ╳ Regeneration error Regenerative circuit error
A．17 ╳ Resolver error The communication of resolver is abnormal.
A．18 ╳ IGBT superheat alarm IGBT temperature is too high.
A．19 ╳ Motor overheat alarm Motor temperature is too high.
A．20 ╳ Power line phase shortage One phase does not bring into main circuit power supply.
A．21 ╳ Instantaneous power off alarm An power off for more than one period is occurred in AC.
Motor temperature detection sensor

A．22 ╳ Encoder cable is error.
is break off.
- 190 -
Alarm Alarm
Alarm Name Meaning
Display Output
A．23 ╳ Brake overcurrent alarm Bleeder resistor is too small, or bleeder module is faulty.
A．41 ╳ Reserved Reserved
The parameter setting of servo drive does not match the

A．42 ╳ Servomotor type error
servomotor.
The parameter setting of servo drive does not match the
A．43 ╳ Servo drive type error
servomotor.
A．44 ╳ Reserved Reserved
Absolute encoder multiturn

A．45 ╳ Absolute encoder multiturn information is faulty.
information error
Absolute encoder multiturn
A．46 ╳ Absolute encoder multiturn information overflow.
information overflow
A．47 ╳ Battery voltage below 2.5V Absolute encoder multiturn information is lost.
A．48 ╳ Battery voltage below 3.1V Battery voltage is too low.
Serial encoder communication Encoder disconnected; encoder signal disturbed; encoder

A．50 ╳
overtime error or encoder decoding circuit error.
Absolute encoder multiturn information may be faulty.
Error reasons：
1.The battery is not connected or the battery voltage is
Absolute encoder overspeed alarm
A．51 ╳ insufficient.
detected
2.The power supply to servo drive is not turned ON when
the battery voltage is normal, or the servomotor running
acceleration is too high due to external reason.
Absolute state of serial encoder
A．52 ╳ Encoder or the encoder decoding circuit is faulty.
error
A．53 ╳ Serial encoder calcaution error Encoder or the encoder decoding circuit is faulty.
Parity bit or end bit in serial encoder Encoder signal is disturbed or the encoder decoding circuit
A．54 ╳
control domain error is faulty.
Serial encoder communication data Encoder signal is disturbed or the encoder decoding circuit
A．55 ╳
checking error is faulty.
End bit in serial encoder control Encoder signal is disturbed or the encoder decoding circuit
A．56 ╳
domain error is faulty.
A．58 ╳ Serial encoder data empty The EEPROM data of serial encoder is empty.
A．59 ╳ Serial encoder data format error The EEPROM data format of serial encoder is incorrect.
Communication module not Communication module is not plugged in or the

A．60 ╳
detected communication module is faulty.
A．61 ╳ Communication unsuccessful CPU of communication module operated abnormally.
Servo drive can not receive the

Receive channel of servo drive data or send channel of
A．62 ╳ period data of communication
communication module is faulty.
module.
- 191 -
Alarm Alarm
Alarm Name Meaning
Display Output
Communication module can not
A．63 ╳ receive the servo drive response Communication module is faulty.
data.
Communication module and bus
A．64 ╳ Bus communication is faulty.
connectionless
CAN communication is faulty because of abnormal
A．66 ╳ CAN communication abnormal
communication connection or disturbance.
A．67 ╳ Receiving heartbeat timeout The master station sends heartbeat time timeout
Synchronization signal monitoring The filling time and the cycle of the synchronous signal
A．69 ╳
cycle is longer than setting does not match.
A．00 〇 Not an error Normal operation status.
〇：Output transistor is ON. ╳：Output transistor is OFF.

A.45、A.46、A.47、A.48、A.51 only can be reset when the absolute encoder related alarm is cleared.
The multiturn data should be cleared because of the multiturn information is incorrect.
- 192 -

L011199 - PRONET-E Series Users Manual - V2.11

Uploaded by

Copyright:

Available Formats

L011199 - PRONET-E Series Users Manual - V2.11

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

L011199 - PRONET-E Series Users Manual - V2.11

Uploaded by

Copyright:

Available Formats

ProNet Series AC Servo User's Manual

Date Rev. No. Section Revised Content Remark

2009-09 V1.00～V1.05 － First edition

2010-02 V1.06 All chapters Completely revised

Addition: Low frequency vibration

4.6.3 Revision: Position reference

5.1.6 Addition: Un017

2011-04 V1.10 4.9.2 Revision: External Torque Limit

1 Addition: Wire-saving incremental encoder

Addition: 4.6.8 Position Control (contact

2011-08 V1.21 Appendix A Revision: Pn006.3

Chapter 4 Addition: Description of /RD signal

All chapters Addition: ProNet-2BD

2011-12 V1.23 3.3.1 Revision: Encoder wiring

4.5.8 Revision: Encoder signal output phase form

4.6.9 Addition: Homing function

2012-02 V1.24 All chapters Addition: ProNet-10D/15D

Appendix B Addition: Alarm A67 and A69

1 Revision: Pn307, Pn304, Pn681, Pn840

1 Add ProNet-E Servo Drive

Revision:Connection Example for

Appendix A.3 Add note ○

Revision : ProNet-30A/ ProNet-50A/

Revision :the value of external regenerative

Revision :the value of external regenerative

Add” Operating Conditions: electric power

2.1 Addition:2.1.7Insatall to the Client

2013-9 V2.05 All chapters Format update

4.5.7 Add: /ZCLAMP

Addition:4.11.8 Torque Detection Output

6.3.3 Revision : Communication data address

Add 100VAC series servo drive:

2014-02 V2.07 All chapters Add ProNet-70

2014-03 V2.08 Chapter 3 Add 3.9 Connecting DC Bus

2014-03 V2.09 Chapter 3 Revision: 3.9 Connecting DC Bus

Add: EML model

2014-04 V2.10 All chapters

2014-06 V2.11 1.1.1 Update Servomotor Model Designation

About this manual

•Specification of the servo drives and servomotors.

•Procedures for installing the servo drives and servomotors.

•Procedures for wiring the servo drives and servomotors.

•Procedures for operating of the servo drives.

•Procedures for using the panel operator.

•Ratings and characteristics.

•Those designing ProNet series servo drive systems.

•Those installing or wiring ProNet series servo drives.

•Those performing trial operation or adjustments of ProNet series servo drives.

•Those maintaining or inspecting ProNet series servo drives.

■ Do not connect the servomotor directly to the local electrical network.

Failure to observe this may result in damage to servomotor.

■ Keep servo drives and other devices separated by at least 10mm.

■ Perform noise reduction and grounding properly.

1. Separate high-voltage cables from low-voltage cables.

2. Use cables as short as possible.

1. Input voltage: AC 1500Vrms, 1 minute

2. Braking current: 100mA

■ Use a fast-response type ground-fault interrupter.

■ Do not make any extreme adjustments or setting changes of parameters.