Hydroleduc Hydraulic Motors en
Hydroleduc Hydraulic Motors en
FIXED DISPLACEMENT
make it simple
2 Contents
M series
MSI series
Options | Accessories
Speed sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Flushing valve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
ATEX certification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
M series
▪ Displacement 5 cc/rev - CETOP
▪ Displacements from 12 to 180 cc/rev - ISO
▪ For fixed and mobile applications
MA
MA series
▪ SAE
▪ Displacements from 10 to 180 cc/rev
▪ For fixed and mobile applications
MSI
MSI series
▪ ISO - semi-integrated
▪ Displacements from 28 to 125 cc/rev
▪ For applications mounted on a planetary gearbox
Accessories
Options
► Main applications
Typical applications are those requiring high torque within a small size.
► Examples of use
Mowers: drive of grass cutting blade, where mechanical solution would be too complicated or impossible;
Blowers: compressor drive;
Wheel drive of undercarriages for construction equipment (motor installed on planetary gearbox);
Industrial of marine winch drive;
Fan drives.
100
90
80
70
60
50
0 100 200 300 400
Pressure (bar)
► Definition of function
Hydraulic motors transform hydraulic flow into rotating speed and hydraulic pressure into mechanical torque.
Motor rotating speed is proportional to the flow which is supplied to it. Torque produced is proportional to the hydraulic pressure the motor
receives.
High quality materials and workmanship. The design choices highlighted below ensure the remarkable reliability and long service life of LEDUC motors.
7 piston design,
ensuring excellent
rotating smoothness
and constant torque.
Reinforced seals
to withstand back pressure
on motor drain return lines.
Before start-up, the motor must be filled with oil. The service life of the motors depends greatly on the quality and the
cleanliness of the hydraulic fluid.
We recommend minimum cleanliness as follows:
NAS 1638 class 9,
SAE class 6,
ISO/DIS 4406 class 20/18/15.
For fluids at very high temperatures 194 to 239 °F (90 to 115 °C), we
recommend a minimum cleanliness class of 19/17/14 according to
ISO 4406.
►Rotating speeds
Fluid viscosities as a function of temperature As an option, HYDRO LEDUC proposes NBR seals, for
operating temperatures from -40 to 176°F (-40 to 80°C).
Temperature °C
IMPORTANT NOTE:
Before start up, ensure the motor is filled with hydraulic fluid:
See section on installation and start-up, page 52.
Operating conditions 7
►Direction of rotation
The motors rotate clockwise or counter-clockwise depending on the direction of hydraulic flow entering the motor.
Clockwise Counter-clockwise
rotation rotation
(CW) (CCW)
T1 T1
T2 T2
B A B A
►Drain pressure
It is essential to drain the motor, T1 or T2, to avoid excessive pressures on the shaft seal.
Maximum acceptable internal pressure depends on motor rotating speed.
However, following these guidelines will avoid problems during operation:
Maximum internal pressure (int P) regardless of rotating speed (continuous): 4 bar;
Maximum internal pressure (int P) regardless of rotating speed (peak): 5.5 bar;
Minimum pressure in the motor housing:
must be greater than ambient (external) pressure (ext P).
8 Determination | Calculating the right motor
Theoretical torque =
Cy x ΔP = Cth
20 π
Torque C = Cth x ηmotor
For example: a 50 cc/rev motor with a ΔP of 250 bar will supply a theoretical torque of 200 N.m.
Average global efficiency of the motor is 90%, actual torque is thus: 180 N.m).
The rotating speed of the hydraulic motor depends on the flow Q which goes through it, and on the displacement of the motor.
Q
N= x 1000
Displ.
►Technical assistance
Our Customer Service would be pleased to assist in determining the right motor for your application.
Determination | Calculating the right motor 9
►Example
1 2 3 4 5 6
A
P A T
M
T B B
1 Motor
WEIGHT
2 Variable displacement pump
4 Valve
5 Hydraulic motor
6 Winch and load
The receiving organ (winch) ⑥ needs to rotate at N = 400 rpm and supply an actual torque of 200 N.m.
The hydraulic pump ② is capable of operating at pressure P up to 350 bar.
Disp. x ΔP
Cth = thus Disp. = 35.9 cc/rev
20 π
Corresponding flow:
▪ For 32 cc/rev motor, Q = 12.8 l/min
▪ For 41 cc/rev motor, Q = 16.4 l/min
10 M series motors
Motor
5 12 18 25 28 32 41 45 50 63 80 90 108 108 R 125 160 180
model
Fr N 710 2800 4000 6000 6200 6500 7000 6500 7500 9000 10500 11000 11500 12500 14500 18000 20000
Fa N/bar * 10 15 20 27 28 30 40 40 40 50 60 67 80 80 86 85 95
Fa
= =
Order code system of M series motors 11
M ... A .. .. M2 . . .. .. To obtain the code for your motor, complete the different parameters
02, 04, 05, 07, 08, 09 and 10 in the table on the left according to the
01 02 03 04 05 06 07 08 09 10 options you require (see table below).
M series
Motor
01 Motor M
Displacement
02 5 12 18 25 28 32 41 45 50 63 80 90 108 108R 125 160 180
Mounting flange
CETOP
2 t bolts
Shaft
DIN 5480 – W25 W25 W25 W30 W30 W30 W30 W30 W30 W40 W40 W40 W45 W45 W50 W50 W1
splined – – – W30 W25 W25 – W35 W35 W35 W35 – – W40 W40 – – W2
04
DIN 6885 Ø 18 Ø 25 Ø 25 Ø 25 Ø 30 Ø 30 Ø 30 Ø 30 Ø 30 Ø 30 Ø 40 Ø 40 Ø 40 Ø 45 Ø 45 Ø 50 Ø 50 D1
keyed – Ø 20 – Ø 30 Ø 25 Ø 25 – Ø 35 Ø 35 Ø 35 – – – Ø 40 – – – D2
Rear 0 – – – ● ● ● ● ● ● ● ● ● ● ● ● ● ● M0
0 – – – ● ● ● ● ● ● ● ● ● ● ● ● ● ● N0
Side
05 1 – – – ● ● ● ● ● ● ● ● ● ● ● ● ● ● N1
0 – ● ● ● ● ● ● ● ● ● ● ● ● – – – – Q0
Threaded
Side
1 – – – ● ● ● ● ● ● ● ● ● ● – – – – Q1
Rear 0 ● ● ● ● ● ● ● ● ● ● ● ● ● – – – – P0
Speed sensor
Yes – ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1
08
No ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 0
Valves
Without ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● SV
09
with flushing valve – – – ● ● ● ● ● ● ● ● ● ● ● ● ● ● VB
PLEASE NOTE: The M5 motor, reference 093840, only exists in one version (see next page).
12 M series motors M 5_093840
79.1
9 T1 : G1/4" 100
8
R53
Ø 127 MAXI
6
39.1
25 Ø 11
°
Ø 80 - 0.046
96 MAXI
0
150
45.50
66.5
53
T2 : G 1/4"
P
150
►Shaft end
0
40 − 0.50
12
P 6
-0.003
Ø 18 +0.008
Ø 25
M6x1
20.5
►Inlet ports
G ½"
38
77
36
139
+1 95
20 0
155 70.7
18.2
81.3
12 45° 45°
M series
6 T1 : M12x1.5
Ø 100
Ø9
39.2
Ø 80 − 0.02
0
70.7
95
40°
51.5
47.5
92.3
13
T3 : M8x1
Ø 16
34.2
T2 : M12x1.5
P
►Shaft
Ø 30
22
Ø 20 ++ 0.015
0.002
+ 0.015
+ 0.002
28
M6x1
Ø 30
Ø 30
22.5
Ø 25
22
►Inlet ports
123.4
P0 Rear threaded ports A and B
143.3
M 22 x 1.5
88
34
58
87
75
87
M 22 x 1.5
+1 118
25 0
Ø 11
56
Ø 100 − 0.02
0
88.4
118
40°
Ø 125
59
69
8
10
15
T3 : M10x1
Ø 17
42.2
T2 : M16x1.5
P
►Shaft end
P P
+1
68 − 0.5
+1
60 − 0.5
0 0
43 - 0.5 35 - 0.5
M 8 x 1.25
M10 x 1.5
Ø 35
Ø 35
19
22
28
27
0 0
50 - 0.5 50 - 0.5 8
8
+ 0.015
+ 0.002
M 10 x 1.5
M 8 x 1.25
+ 0.015
25 + 0.002
Ø 35
Ø 35
28
33
Ø 30
Ø
19 22
►Inlet ports
M series
M27x2 depth 16
65.1
78.9
107.2
107.2
58 120
M27x2 depth 16
159.4 142.9
179.2 179.2
40.5
59
66.6
70
107.2
M27x2
107.2
depth 16
149 144.6
179 179.3
N0 N1 or
Side flange ports A and B
SAE 1/2″ 6000 psi
18
.2 120
66.1
107.2
M 8 depth 15
Ø 11
.5
40
144.1
179
+1
118
25 0
107.70 T1 : M16x1.5 88.4
8
Ø 11
56
Ø 100 − 0.02
0
88.4
118
40°
59
Ø 125
69
8
10
15
T3 : M10x1
Ø 17
42.20
T2 : M16x1.5
P
►Shaft end
M 8 x 1.25
Ø 35
Ø 35
27 28
0
0
50 − 0.5 50 - 0.5
8 8
M 8 x 1.25
+ 0.002
+ 0.015
+ 0.015
Ø 25 + 0.002
M 10x1.5
Ø 35
28
Ø 35
33
Ø 30
22 19
►Inlet ports
M series
Ø 11
M8 depth 15
18.2
Ø 11
59
115
40.5
75.4
88.3
112
112
18.2 40.5
40
M8 depth 15
155 drilling depth 18
155.2
185 185
N0 N1 or
Side flange ports A and B
SAE 1/2″ 6000 psi Q0 Side threaded ports A and B
120 120
18
.2
70.3
71.2
M27x2 depth 16
112.3
112
M8 depth 15
Ø 11 drilling depth 18
.5
150.2
40
149
185 185.3
M27x2 depth 16
58
71.7
112.3
84
112.3
+1
32 0 150
118.70 113.14
30
12 T1 : M18x1.5
Ø 13.50
59
− 0.02
0
113.14
150
Ø 125
40°
75
Ø 160
84
5
12
11
T3 : M12x1.5
Ø 20.3
50.20
T2 : M18x1.5
P
►Shaft end
0 0
35 − 0.5 40 − 0.5
M 12 x 1.75
M 12 x 1.75
Ø 40
Ø 40
27 28
28 32
0 0
60 − 0.5 60 − 0.5 10
8
M 12 x 1.75
M 12 x 1.75
+ 0.002
+ 0.015
+ 0.02
35 0
Ø 40
Ø 40
38
33
Ø 30
28 28
►Inlet ports
M series
50.8
23.8
M10 depth 17
Ø 17
147
75
50.8
91
103.3
75
125.9
125.9
Ø 17
23.8
M10 depth 17
49
177.7
176
202.5 202
N0 N1 or
SAE flange ports, side A and B
SAE 3/4″ 6000 psi 136
P0 Rear threaded ports
M33 x 2 depth 18
23
.8
84.5
100.3
129
127.9
58
M 10 depth 17
Ø 17
187
.8
210.2
50
168.2
211.7
M33x2
depth 18
128.2
85.3
84.2
M33x2
depth 18
127.9
136
168.2 169.2
210.2 210.6
122.7 165
20
+1
32 0 127.3
29 T1 : M18x1.5
10
Ø 13.50
68
Ø 140 − 0.02
0
127.3
165
40°
82.50
Ø 180
90.50
3
13
T3 : M12x1.5
14
Ø 23
T2 : M18x1.5
63.20
►Shaft end
0 0
45 − 0.5 70 − 0.5
12
+ 0.015
+ 0.002
M 16 x 2
M16 x 2
Ø 45
43
Ø 45
Ø 40
36 36
37
0
40 − 0.5
M 12 x 1.75
Ø 45
25
32
►Inlet ports
M series
M12 depth 20
Ø 23
166
84
57.2
E
27.8
62.5
D M 80-90 M 108
116
A 242.7 243.3
136.3
B 216.3 216.9
C
C 146.4 146.9
D 114.9 115.4
200 E 68 66
B
230.2 M33x2 M42x2
A F depth 18 depth 20
Ø 23
84 E
M12 depth 20
M 80-90 M 108
D
F A 242.7 243.3
99.2
B 192.5 194.4
136.3
C 146.4 146.9
C
D 95 96.6
E 160 160
197.5 B F M33x2 M42x2
225.7 A depth 18 depth 20
N0 N1 or
SAE flange ports, rear
SAE 1″ 6000 psi Q1 Side threaded ports
160
160
27
.8
96.6
147.4
96.6
148.1
M 12 x 175
depth 20
Ø 23
M33x2 depth 18
194.4
243.8
.2
194.4
57
245
+1
40 0 152.1 190
87.50
141.4
36.50 23
T1 : M18x1.5
Ø 17.50
59.9
Ø160 - 0.025
141.4
0
190
40°
Ø 200
107.5
98
4
16
10
22.50
T 3 : M14x1.5 T2 : M18x1.5
65
P
►Shaft end
+1
P P
+1
90 − 0.5 120 − 0.5
0
80 − 0.5
0
14
50 − 0.5
+ 0.018
+ 0.002
M 16 x 2
M16 x 2
48.5
Ø 55
Ø 55
Ø 45
36 36
40
M12 x 1.75
Ø 40 ++ 0.018
Ø 55
Ø 55
43
28 28
36
Max. pressure 5076 (350 bar) for M 125. For M 108 R only.
►Inlet ports
M series
66.7
66.7
M14 depth 19 M14 depth 19
198
99
198
99
Ø 30
Ø 30
117.8
119.7
146.3
148.2
209.5 211.8
243.5 245.8
31.8
Ø 31
99 Ø 31
99
118
120.2
155
156.9
228.2
230.8
259.2 261.5
N0 N1 or
SAE flange ports
SAE 1¼″ 6000 psi N0 N1or
SAE flange ports
SAE 1¼″ 6000 psi
M 108 R M 125
178 178
31 31
.8 .8
98.9
100.8
.7
.7
66
159.9
66
158
Ø 31 Ø 31
M14 depth 19 M14 depth 19
205.3 207.6
263 265.3
210
40 + 10 176
158.4
37.25 109.60
Ø 17.50 45°
10 45°
25
T1 : M22x1.5
Ø 224
68.3
Ø 180 − 0.03
+0
158.4
210
°
40
106
110
30.80
T3 : M14x1.5
Ø 24
T2 : M22x1.5
P 72
►Shaft end
+1
P P
95 − 0.5 130
+1
− 0.5
0 0
55 − 0.5 90 − 0.5
14
+ 0.018
Ø 50 + 0.002
M 16 x 2
M 16 x 2
Ø 60
53.5
Ø 60
36 36
40
►Inlet ports
M series
Ø 32 31.80
66.70
199
99
M14 depth 19
170
146.1
249
290
Ø 32
66.70
31
.80
107.7
120
170
170
Ø 32
M14 depth 19
.70
66
253 238
295
290
Intermittent
Continuous Torque Theoretical maximal Max. allowable
Motor max. Max. flow Weight
Displacement max. speed Torque at 350 bar power at 5800 psi pressure
model speed absorbed (kg)
(1) (5100 psi) 400 bar continuous / peak
(1)
cu.in/rev cc/rev rpm rpm gpm l/mn lbf.ft/psi N.m/bar lbf ft N.m HP kW psi bar lbs Kg
MA 10 0.62 10.2 8000 8800 21.6 82 0.0082 0.16 42 57 72.9 54.4 5800 / 6525 400 / 450 14.3 6.5
MA 12 0.73 12.0 8000 8800 25.4 96 0.0097 0.19 49 67 85.7 64 5800 / 6525 400 / 450 14.3 6.5
MA 18 1.10 18.0 8000 8800 38.0 144 0.0145 0.29 74 100 128.7 96 5800 / 6525 400 / 450 14.3 6.5
MA 25 1.52 24.9 6300 6900 41.4 157 0.0201 0.40 102 139 140.1 104.5 5800 / 6525 400 / 450 25 11.5
MA 32 1.96 32.1 6300 6900 53.4 202 0.0259 0.51 132 179 180.7 134.8 5800 / 6525 400 / 450 25 11.5
MA 41 2.51 41.1 5600 6200 60.8 230 0.0331 0.65 169 229 205.6 153.4 5800 / 6525 400 / 450 25 11.5
MA 45 2.77 45.4 5000 5500 60.0 227 0.0366 0.72 187 253 202.8 151.3 5800 / 6525 400 / 450 40 18
MA 50 3.07 50.3 5000 5500 66.4 252 0.0405 0.80 207 280 224.7 167.6 5800 / 6525 400 / 450 40 18
MA 63 3.84 63.0 5000 5500 83.2 315 0.0508 1.00 259 351 281.5 210 5800 / 6525 400 / 450 40 18
MA 80 4.91 80.4 4500 5000 95.6 362 0.0648 1.28 330 448 323.3 241.2 5800 / 6525 400 / 450 51 23
MA 90 5.49 90.0 4500 5000 107.0 405 0.0725 1.43 370 501 361.9 270 5800 / 6525 400 / 450 51 23
MA 108R 6.61 108.3 3400 4500 97.3 368 0.0872 1.72 445 603 329 245.4 5800 / 6525 400 / 450 77 35
MA 125 7.65 125.4 3400 4500 112.6 426 0.1010 2.00 515 699 381 284.2 5800 / 6525 400 / 450 77 35
MA 160 9.76 160.0 3600 4000 152.2 576 0.1289 2.55 657 891 514.7 384 5800 / 6525 400 / 450 107 48.5
MA 180 11.02 180.6 3600 4000 171.8 650 0.1455 2.87 742 1006 581 433.4 5800 / 6525 400 / 450 107 48.5
lbf 528 630 900 1350 1462.5 1574 1462.5 1686 2023 2360 2473 2812 3262 4050 4500
Fr
N 2350 2800 4000 6000 6500 7000 6500 7500 9000 10500 11000 12500 14500 18000 20000
lbf/psi 0.19 0.23 0.31 0.42 0.46 0.62 0.62 0.62 0.77 0.93 1.03 1.24 1.33 1.32 1.47
Fa N/psi 0.83 1.03 1.37 1.86 2.06 2.75 2.75 2.75 3.44 4.14 4.62 5.52 5.93 5.86 6.55
(N/bar) * (12) (15) (20) (27) (30) (40) (40) (40) (50) (60) (67) (80) (86) (85) (95)
Fr
Fa
= =
Order code system of MA series motors 27
MA ... C .. .. U2 . . .. .. To obtain the code for your motor, complete the different parameters
02, 04, 05, 07, 08, 09 and 10 in the table on the left according to the
01 02 03 04 05 06 07 08 09 10 options you require (see table below).
Motor
01 Motor MA
Displacement
02 10 12 18 25 32 41 45 50 63 80 90 108R 125 160 180
Mounting flange
03 SAE B 2 bolts SAE C 4 bolts SAE D 4 bolts C
Shaft
13 T 13 T 13 T 14 T 14 T 14 T 14 T 14 T 14 T 14 T 14 T 13 T 13 T 13 T 13 T
16/32 DP 16/32 DP 16/32 DP 12/24 DP 12/24 DP 12/24 DP 12/24 DP 12/24 DP 12/24 DP 12/24 DP 12/24 DP 8/16 DP 8/16 DP 8/16 DP 8/16 DP S1
SAE B SAE B SAE B SAE C SAE C SAE C SAE C SAE C SAE C SAE C SAE C SAE D SAE D SAE D SAE D
MA series
17 T 17 T
Splined SAE J498b – – – – – – – – 12/24 DP 12/24 DP – – – – S2
SAE C-C SAE C-C
04 – – – – – – – – –
21 T 21 T
– – – – S3
16/32 DP 16/32 DP
Ø1’’ Ø1’’ Ø1’’ Ø1 1/4’’ Ø1 1/4’’ Ø1 1/4’’ Ø1 1/4’’ Ø1 1/4’’ Ø1 1/4’’ Ø1 1/2’’ Ø1 1/2’’ Ø1 3/4’’ Ø1 3/4’’ – – K1
Keyed SAE J744
– – – – – – – – – – – – – – – K2
Rear 0 – – – ● ● ● ● ● ● ● ● ● ● ● ● M0
0 – – – ● ● ● ● ● ● ● ● ● ● ● ● N0
Side
05 1 – – – ● ● ● ● ● ● ● ● ● ● ● ● N1
0 ● ● ● ● ● ● – – – – – – – – – Q0
Threaded
Side
1 – – – ● ● ● – – – – – – – – – Q1
Rear 0 ● ● ● ● ● ● ● – – – – – – – – P0
Speed sensor
Yes ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 1
08
No ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● 0
Valves
Without ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● SV
09
With flushing valve – – – ● ● ● ● ● ● ● ● ● ● ● ● VB
6.85 (174)
3.66 (93)
5.75 (146)
0.31 (7.90) 0.55 (14) T1 : 9/16''-18UNF-2B
1.65 (42)
– 0.002 (101.60)
Ø 0.55 (14)
4.76 (121)
Ø 4.00 +0.000
40°
2.03 (51.50)
T2 : 9/16-18UNF-2B
P 6.53 (166)
►Shaft end
P
5/16"-18UNC-2B
1.63 (41.40) P
5/16"-18UNC-2B
1.81 (46)
0.78 (20) +0.001
0.25 – 0.0 (6.35)
1.26 (32)
±0.005 (28.09)
Ø 1.18 (30)
Ø 1.18 (30)
+0.000
1.106
►Inlet ports
7/8"-14UNF-2B
depth 0.59 (15)
1.34 (34)
3.46 (88)
2.29 (58.04)
2.95 (75)
MA series
7/8"-14UNF-2B
5.27 (133.9) depth 0.59 (15) 6.06 (154)
4.51 (144.55)
Ø 0.55 (14.30)
Ø 6.38 (162)
2.20 (56)
(127)
4.51 (144.55)
5.75 (146)
– 0.001
+0.000
40°
Ø 5.00
2.71 (69)
4.22 (107.16)
2.20 (56)
0.50 (12.70)
T2 : 3/4"-16UNF-2B
P
7.59 (192.8) 5.75 (146)
►Shaft end
P
2.2 (55.9)
P 2.2 (55.9)
+0.001
1.57 (40) 0.3125 – 0.0 (7.94)
1.38 (35)
7/16"-14UNC-2B
(31.75)
(35.20)
7/16"-14UNC-2B
Ø 1.38 (35)
Ø 1.38 (35)
– 0.002
+0.000
±0.005
Ø 1.25
1.386
►Shaft end
N0 N1 or
Side SAE flange ports A and B
SAE 1/2″ 6000 psi M0 Rear SAE flange ports A and B
SAE1/2″ 6000 psi
0.071 (18.2)
Ø 0.43 (11)
5/16"-18UNC-2B
depth 0.71 (18)
1.61 (29.5)
2.32 (59)
4.72 (120)
2.77 (70)
2.60 (66)
5/16"-18UNC-2B
4.22 (107)
depth 0.71 (18)
Ø 0.43 (11)
.5)
(40
MA series
6.41 (163)
9
0.
1.5
15/16"-12UN-2B
depth 0.79 (20)
4.72 (120)
1.61 (29.5)
2.64 (67.2)
2.75 (70)
2.32 (59)
4.22 (107)
4.22 (107)
15/16"-12UN-2B
depth 0.79 (20)
4.72 (120)
2.57 (65.4)
11/16"-12UN-2B
depth 0.75 (19)
4.58 (116.3)
6.18 (157.1)
8.72 (221.4)
4.51 (114.55)
Ø 0.56 (14.30)
Ø 6.38 (162)
2.20 (56)
(127)
4.51 (114.55)
5.75 (146)
– 0.001
+0.000
40°
Ø 5.00
2.71 (69)
4.42 (112.05)
2.20 (56)
0.50 (12.70)
T2 :3/4"-16UNF-2B
►Shaft end
P
2.2 (55.9)
P 2.2 (55.9)
+0.001
1.57 (40) 0.3125 – 0.0 (7.94)
1.38 (35)
7/16"-14UNC-2B
(31.75)
(35.20)
7/16"-14UNC-2B
Ø 1.38 (35)
Ø 1.38 (35)
– 0.002
+0.000
±0.005
Ø 1.25
1.386
►Inlet ports
(18.2)
0.071
depth 0.71 (18)
Ø 0.43 (11)
(18.2)
0.071
Ø 0.43 (11)
1.59 1.61 1.59 (40.5)
(40.5) (29.5)
2.97 (75.6)
3.48 (88.3)
4.42 (112)
4.42 (112)
MA series
6.64 (168.5) 6.53 (169)
7.84 (199.1) 7.84 (199.1)
N0 N1 or
Side flange ports A and B
SAE 1/2″ 6000 psi P0 Rear threaded ports
15/16"-12UN-2B
depth 0.79 (20)
1.61 (29.5)
2.32 (59)
4.72 (120)
2.80 (71.2)
2.97 (75.6)
4.42 (112)
5/16"-18UNC-2B
depth 0.71 (18)
(40 .59
6.53 (169)
.5)
0
1
(18 .71
.2) 7.84 (199.1)
6.45 (163.8) Ø 0.43 (11)
11/16"-12UN-2B
2.85 (72.3)
2.78 (70.6)
4.78 (121.5)
15/16"-12UN-2B
depth 0.79 (20)
4.51 (114.55)
5.75 (146)
5.5 (139.7)
T1 : 3/4"-16UNF-2B 45° 45°
0.31 (7.90) 0.79 (20) Ø 0.56 (14.30)
2.32 (59)
(127)
4.51 (114.55)
5.75 (146)
– 0.001
+0.000
Ø 5.00
40°
3.31 (84)
4.96 (126)
Ø 6.38 (162)
0.50 (12.70)
2.80 (71)
T2 : 3/4"-16UNF-2B
P 8.79 (223)
►Shaft end
P
2.2 (55.9)
P 2.2 (55.9)
+0.001
1.57 (40) 0.3125 – 0.0 (7.94)
7/16"-14UNC-2B
1.358 (34.5)
(31.75)
1.386 ±0.005 (35.20)
7/16''-14UNC-2B
0.002
Ø 1.57 (40)
Ø 1.25 –+0.000
Ø 1.57 (40)
►Inlet ports
3/8"-16UNC-2B
(23.8)
0.93
depth 0.79 (20)
2 (50.8)
1.47 2 (50.8)
Ø 0.66 (17) (37.5) 1.47 (37.5)
2.95 (75) 2.95 (75)
4.07 (103.3)
3.58 (91)
4.96 (126)
MA series
7.75 (197)
7.82 (198.7)
8.8 (223.5)
N0 N1 or
SAE flange ports, side A and B
SAE 3/4″ 6000 psi P0 Rear threaded ports
15/16"-12UN-2B
depth 0.79 (20)
1.47 (37.5)
5.34 (136) 2.95 (75)
3.33 (84.5)
3.58 (91)
3/8"-16UNC-2B
depth 0.79 (20)
5.08 (129)
.8)
50
2(
7.75 (197)
0
(23 .93
.8) Ø 0.66 (17)
7.44 (189) For MA 45 only.
9.16 (232.7)
4.51 (114.55)
T1 : 7/8"-14UNF-2B
0.31 (7.90) 0.79 (20) Ø 6.38 (162) 45° 45°
2.67 (68)
(127)
4.51 (114.55)
5.75 (146)
– 0.001
+0.000
Ø 5.00
°
40
3.54 (90)
5.35 (136)
4 x Ø 0.56 (14.30)
3.31 (84)
P T2 : 7/8"-14UNF-2B
9.71 (247)
►Shaft end
P
2.2 (55.9) 2.44 (61.9)
7/16"-14UNC-2B
Ø 1.77 (45)
Ø 1.77 (45)
– 0.002 (38.10)
±0.005 (42.26)
7/16"-14UNC-2B
Ø 1.77 (45)
Ø 1.77 (45)
+0.00
Ø1.50
1.664
1.1 (28)
1.10 (28)
1.89 (48)
2.13 (54)
►Inlet ports
3.30 (84)
1.63 (42) Ø 0.90 (23)
1.09 (27.8)
1.09 (27.8)
7/16"-14UNC-2B
depth 0.78 (20)
2.25 (57.2) 2.25 (57.2)
1.65 (42)
3.30 (84)
7/16"-14UNC-2B
depth 0.78 (20)
5.35 (136)
3.90 (99)
MA series
4.56 (116)
5.35 (136)
8.69 (220.7)
8.59 (218)
9.88 (251)
9.71 (247)
N0 N1 or
SAE flange ports, side A and B
SAE 1 ″ 6000 psi
6.30 (160)
1.0
3.80 (96.6)
9(
27
7/16"-14UNC-2B .8)
depth 0.78 (20)
5.83 (148.1)
Ø 0.90 (23)
.2)
57
5(
2.2
8.47 (215)
10.16 (265.7)
7.87 (200)
6.10 (154.90) 6.36 (161.6)
4.52 (114.90) 45°
0.31 (7.90) 45°
0.98 (24.90)
T1 : 7/8"-14UNF-2B
Ø 0.81 (20.60)
3.35 (85)
Ø 9.00 (228.60)
Ø 6.00 – 0.002 (152.40)
6.36 (161.6)
7.87 (200)
+0.000
40°
4.27 (108.50)
0.50 (12.70)
3.70 (94.10)
T2 : 7/8"-14UNF-2B
►Shaft end
P
2.94 (74.6)
20.5 (52)
5/8"-11UNC-2B
Ø 2.16 (55)
1.30 (33)
2.63 (66.70)
5/8"-11UNC-2B
Ø 2.16 (55)
– 0.002
±0.005
+0.00
Ø 1.75
1.941
1.30 (33)
2.63 (66.70)
►Inlet ports
1.25 (31.80)
C 5.76 (146.3) 5.84 (148.2)
D 4.64 (117.8) 4.71 (119.7)
1/2"-13UNC-2B
depth 0.75 (19)
2.63 (66.70)
Ø 1.21 (31)
3.90 (99)
1/2"-13UNC-2B
depth 0.75 (19)
MA series
4.72 (120)
6.18 (156.9)
D
B 10.15 (258)
A 11.37 (288.9)
N0 N1 or
SAE flange ports, side A and B
SAE 1¼″ 6000 psi
MA 108R MA 125
A 11.35 (288.4) 11.52 (292.7)
B 9.16 (232.7) 9.25 (235)
C 6.14 (156) 6.30 (159.9)
D 3.89 (98.9) 3.97 (100.8)
7.01 (178)
1
1/2"-13UNC-2B (31 .25
.80
depth 0.75 (19) )
D
C
)
.70
66
3(
2.6
B Ø 1.21 (31)
7.87 (200)
6.36 (161.6)
9.19 (208.1)
0.31 (7.9) 45°
0.98 (25) 45°
Ø 0.83 (21)
T1 : 7/8"-14UNF-2B
Ø 9.00 (228.60)
2.69 (68.3)
Ø 6.00 – 0.002 (152.40 – 0.05 )
+0.0
6.36 (161.1)
7.87 (200)
+0.0
40°
4.13 (105)
0)
(18
9
7.0
0.50 (12.70)
3.97 (100.9)
P T2 : 7/8"-14UNF-2B
►Shaft end
2.15 (54.5)
5/8"-11UNC-2B
Ø 2.36 (60)
0.47 (12)
1.42 (36)
2.64 (67)
Ø 2.36 (60)
M16 x 2
+0.001
– 0.0
Ø 1.968
0.47 (12)
1.42 (36)
3.54 (90)
►Inlet ports
7.64 (194)
2.63 (66.70)
3.90 (99)
1.25 (31.80)
Ø 1.25 (32)
1.25 (31.80)
1/2"-13UNC-2B
depth 0.75 (19)
2.63 (66.70)
Ø 1.25 (32)
3.90 (99)
1/2"-13UNC-2B
depth 0.75 (19)
MA series
4.73 (120)
5.75 (146)
6.69 (170)
6.69 (170)
11.06 (281) 11.22 (285)
1/2"-13UNC-2B
depth 0.75 (19)
1
(31 .25
.80
)
4.24 (108)
6.69 (170)
)
.70
66
3(
2.6
Ø 1.25 (32)
10.6 (270)
12.87 (327)
Max. allowable
Continuous Intermittent max. Max. flow Torque
Motor Displacement Torque pressure Weight
max. speed (1) speed (1) absorbed at 350 bar
model (cc/rev) (N.m/bar) continuous / peak (kg)
(rpm) (rpm) (l/mn) (N.m)
(bar)
MSI 28 27.7 6300 6900 175 0.44 154 400 / 450 11.5
MSI 32 32.1 6300 6900 202 0.51 179 400 / 450 11.5
MSI 41 41.1 5600 6200 230 0.65 229 400 / 450 11.5
MSI 50 50.3 5000 5500 252 0.80 280 400 / 450 19
MSI 63 63 5000 5500 315 1.00 351 400 / 450 19
MSI 80 80.4 4500 5000 362 1.28 448 400 / 450 26
MSI 90 90 4500 5000 405 1.43 501 400 / 450 26
MSI 108 108.3 4000 4400 433 1.72 603 400 / 450 26
MSI 108 R (2) 108.3 3400 4500 368 1.72 603 400 / 450 33
MSI 125 125.4 3400 4500 426 2.00 699 400 / 450 33
Motor
28 32 41 50 63 80 90 108 108 R 125
model
Fr N 6200 6500 7000 7500 9000 10500 11000 11500 12500 14500
Fa N/bar * 28 30 40 40 50 60 67 80 80 86
Fr
Fa
= =
Order code system of MSI series motors 43
MSI ... B ... L0 M1 . . SV To obtain the code for your motor, complete the different parameters 02, 04,
07 and 08, in the table on the left according to the options you require (see
01 02 03 04 05 06 07 08 09 table below).
Motor
01 Semi-integrated motor MSI
Displacement
02 28 32 41 50 63 80 90 108 108 R 125
Mounting flange
03 2 bolts ISO 3019-2 B
Shaft
04 W30 W30 W30 W30 W30 W40 W40 W40 W40 W45 W1
DIN 5480 splined
- - - - W35 W35 W35 - - W40 W2
Inlet ports
SAE flange ports,
05 ● ● ● ● ● ● ● ● ● ● L0
bottom
Drain
06 1 1 1 1 1 1 1 1 1 1 M1
MSI series
Suitable for use of speed sensor
Yes ● ● ● ● ● ● ● ● ● ● 1
07
No ● ● ● ● ● ● ● ● ● ● 0
Speed sensor
Yes ● ● ● ● ● ● ● ● ● ● 1
08
No ● ● ● ● ● ● ● ● ● ● 0
Valves
09 Without ● ● ● ● ● ● ● ● ● ● SV
44 MSI series motors MSI 28 - 32 - 41
121.5 188
39 160
T1 : M16x1.5
72.4
41
Ø 135 h6
Ø 105
Ø 94
°
40
184.8
Ø 14
112.3
15
+ 0.2
89.1 − 0.4
Ø 154
P
►Shaft end
0
35 − 0.5
22
M 10 x 1.5
Ø 35
27
►Inlet ports
115
59
Ø 11
88.3
18.2
40
91.4
111.6
142 235
200
56
T1 : M18x1.5
85.3
36.2
Ø 119
Ø 110
Ø 160 h6
°
40
211.2
Ø 18
126
15
+ 0.2
92.5 − 0.4
P Ø 190
►Shaft end
28 28
MSI series
M12 x 1.75
M12 x 1.75
Ø 40
Ø 40
27 32
►Inlet ports
M10 depth 17
Ø 17
147
75
50.8
103.3
23.8
52
118
152 260
63.4 224
100.4
T1 : M18x1.5
33.8
Ø 190 h6
Ø 120
Ø 136
°
40
236.7
Ø 22
15 136
+ 0.2
110.5 − 0.4
P Ø 220
►Shaft end
36 25
M12 x 1.75
M16 x 2
Ø 45
Ø 45
Not available on
MSI 108.
Max. pressure:
37 32
350 bar for MSI 90.
►Inlet ports
M12 depth 20
Ø 23
166
84
57.2
116
27.8
62.5
122
161 286
71.7 250
T1 : M18x1.5
103
57.3
- 0.029
0
Ø 138
Ø 160
Ø 200
40°
Ø 22
249.3
146.3
15
Ø 232
+ 0.20
122.80 - 0.40
►Shaft end
0
45 - 0.50
25
MSI series
M12 x 1.75
Ø 55
36
►Inlet ports
99
198
Ø 30
117.8
M14 depth 19
126.7
163 286
71.7 250
T1 : M18x1.5
103
57.3
160
138
200 − 0.029
0
251.2
°
40
Ø 22
148.2
15
+ 0.2
122.8 − 0.4
P Ø 232
►Shaft end
P +0.2
P
+ 0.2
172.8 − 0.9 167.8 - 0.9
0 0
50 - 0.5 45 - 0.50
36 25
M12 x 1.75
M16 x 2
Ø 55
Ø 55
40 36
►Inlet ports
M14 depth 20
Ø 30
99
198
66.7
119.7
31.8
69.2
129
S P E E D S E N S O R & I N D I C AT O R O F D I R E C T I O N O F R O TAT I O N
LEDUC CODE: 093327
M, MA, MSI series motors can be fitted with an induction type speed sensor, to measure rotating speed and also direction of rotation.
This accessory may only be used on motors which are suitably adapted to take it (see the order code system).
A F
►Technical data for the sensor
Protection type IP 69 k
Operating temperature – 104°F…+ 257°F (– 40°C…+ 125°C)
Weight around 65 g
Cable length 50 cm
C
33
Ø 14
20
15
Ø 6.50
A B C
Series Motor models Number of teeth *
(mm) (mm) (mm)
M 12 - 18 152 33 88 30
M 25 169 32 91 33
M 28 - 32 - 41 174 28 91 33
M M 45 - 50 - 63 192 24 98 39
M 80 - 90 - 108 218 18 103 44
M 108R - 125 225 46 121 64
M 160 - 180 250 47 126 68
MA 10 - 12 - 18 162 32 87 30
MA 25 173 41 92 35
MA 32 - 41 173 41 92 35
MA
Accessories
MA 45 - 50 - 63 193 35 96 39
Options
MA 80 - 90 223 30 101 44
MA 108R - 125 251 45 122 64
MA 160 - 180 282 47 126 68
MSI 28 - 32 - 41 97 43 91 35
MSI 50 - 63 117 36 96 39
MSI MSI 80 - 90 - 108 125 31 101 44
MSI108 R - MSI 125 142 45 122 64
* The motors suitable for use with a speed sensor are fitted with a gear wheel on the barrel.
When this barrel rotates, it produces a signal proportional to rotating speed, and which is picked up by the sensor.
Used to create flow to cool the motor. This valve is essential for all intensive uses of motors and contributes to long service life.
The valve takes some hydraulic fluid from the return connection port (low pressure) and reinjects it into the motor housing.
This is then evacuated via the motor drain line.
Flushing valves are only available for use with motors with side ports (N1 or Q1).
►Dimensions
X
X Y
Series Motor models
(mm) (mm)
M 25 207 116
M 28 - 32 - 41 213 121
M 45 - 50 - 63 235 137
M M 80 - 90 - 108 265 153
M 108R 273 153
M 125 275 155 Y
M 160 - 180 313 172
MA 25 221 116
MA 32 - 41 228 122
MA 45 -50 - 63 256 137
MA MA 80 - 90 286 153
MA 108 R 305 157
MA 125 307 159
MA 160 - 180 345 170 7)
(11
B A
MB MA
A B B S1 A
Options | Accessoires 51
ATEX CERTIFICATION
►Explanation
Group II category 2 means it is possible to operate in an ATEX 1 zone (probable gas atmosphere) or ATEX 21 zone (probable dusty atmosphere).
G = May operate in a gas zone.
D = May operate in a dusty atmosphere.
TX = Maximum surface temperature.
The marking of our product will be: Group II category 2GD c TX (where TX replaces T3 and T4).
Our products are TX registered (based on product surface temperature) and can therefore be certified T4 or T3 according to the following
recommendations (hot area).
►Surface temperature
CE II 2 GD c TX HL1
If you have different requirements, please contact us. Accessories
Options
IMPORTANT NOTE: ATEX certification does not apply to motors fitted with speed sensor, nor to the “drainless” motors.
52 Installation & start-up
Motor in rotation Motor in rotation Motor in rotation Motor in rotation Motor capable
CCW CW CW CCW of rotation
pressure in A pressure in B pressure in B pressure in A CCW and CW
45° 45° Fr
70° 70° Fr Fr
Fr Fr
B A B A B A B A B A
LEDUC motors can be used in only mounting position. In ″shaft upwards″ position, make sure that the motor housing is completely filled with
fluid (for M motors, bleed the air by the T3 connection). The T3 connection is only available for M series motors.
M | MA MSI
2nd drain port
available on request.
T3
Drainless motor
bent axis hydraulic motor
HYDRO LEDUC is now able to offer drainless motors for either single direction
of rotation or bi-directional use, under certain conditions and on request
(giving details of your application).
A D VA N TA G E S
No drainline needed
► Only two hose lines are required: supply line and output.
► The motor is drained through the return line.
It is fitted with a high pressure lip seal.
CHARACTERISTICS
Working speed:
Please consult our Technical Department
with details of your applications.
Please contact our Customer Service Department with details of your application.
54 The LEDUC range
HYDRO LEDUC offers 3 types of piston The W range is composed of fixed Fixed displacement piston motors.
pumps perfectly suited to all truck and displacement pumps, and the DELTA ▪ Models from 5 to 180 cc/rev.
PTO-mount applications. range, of variable displacement pumps. ▪ Available in ISO, SAE
These pumps can operate at high and semi-integrated versions.
▪ Fixed displac. from 12 to 130 cc/rev pressures within minimal size.
▪ Variable displac. from 40 to 150 cc/rev
► W and WA (SAE)* pumps:
▪ Fixed displac. from 12 to 125 cc/rev
▪ ISO 3019/2 or SAE flanges
▪ DIN 5480 or SAE shafts
► DELTA pumps: M
XPi ▪ Variable displac. from 40 to 92 cc/rev
▪ SAE shafts and flanges
XAi
MA
PA
PAC
PAD DELTA W
MSI
TXV
55
HYDROPNEUMATIC MICRO
ACCUMULATORS HYDRAULICS
@
A passion for hydraulics
HYDRO HYDRO
LEDUC LEDUC
SAS SAS
Head office
Siège& social
Factory
& Usine
BP 9 -BPF-54122
9 - F-54122
AZERAILLES
AZERAILLES
- FRANCE
(FRANCE)
Tél . +33
Tél(0)3
. +3383(0)3
76 77
83 40
76 -77
Fax
40+33
- Fax
(0)3
+3383(0)3
75 21
83 58
75 21 58
HYDRO
HYDROLEDUCLEDUCGmbH
GmbH
Haselwander
HaselwanderStr.
Str.5 5
D-77746
D-77746SCHUTTERWALD
SCHUTTERWALD- (GERMANY)
GERMANY
Tel.
Tel.+49
+49(0)
(0)781-9482590
781-9482590- -Fax
Fax++49
49(0)
(0)781-9482592
781-9482592
HYDRO
HYDROLEDUCLEDUCAB AB
Göteborgsvägen
Batterivägen 574
461
SE-433
38 TROLLHÄTTAN
02 SÄVEDALEN- (SWEDEN)
SWEDEN
Tel.
Tel.
+46
46 (0)
(0) 702
520 61
10 77
82070
HYDRO
HYDROLEDUCLEDUCN.A.
N.A.Inc.
Inc.
19416
19416Park
ParkRow
Row- -Suite
Suite170
170
HOUSTON,
HOUSTON,TEXAS
TEXAS77084
77084- (USA)
USA
Tel.
Tel.+1
+1281
281679
6799654
9654- -Fax
Fax+1
+1832
832321
3213553
3553
make it simple
HYDRO LEDUC
SAS with capital of 4 065 000 €
EORI FR31902742100019
RC Nancy B 319 027 421
www.hydroleduc.com
contact@hydroleduc.com
EN_201602_Motors_CB