Data sheet SSAB Domex Tube Double Grade 2017-04-25

SSAB Domex Tube Double Grade

General Product Description

SSAB Domex Tube Double Grade is structural hollow section.
It meets or exceeds the requirements of standard EN 10219 and includes two separate modern steel grades: S355J2H and S420MH. The choice
of grade depends on the customer’s or designer’s application and requirements.
When your main goal is excellent usability or simplicity of design, grade S355 presents the best choice. If you are looking for considerable
weight reduction and longer spans, consider selecting grade S420MH.
Welding and other workshop instructions and regulations like welding procedure test (ISO 15614-1), material classification (ISO 15608), welding
qualification (EN 287-1; ISO 9606-1) and EN 1090 certification procedure must follow the appropriate steel grade S355 or S420 selected.
Welding in corner areas is always permitted when using SSAB steels.
 
Dimension Range
SSAB Domex Tube Double Grade is available at circular, square and rectangular shapes. 
   
Circular 26.9- 323.9 mm 
Square 25x25- 300x300 mm 
Rectangular 40x20- 400x200 mm 
Wall thickness 2.0- 12.50 mm
Mill length 6000- 12 000/18 000 mm
Other shapes and sizes are available upon request.

Dimensions
Circular
Diameter 2.0mm 2.5mm 3.0mm 4.0mm 5.0mm 6.0mm 6.3mm 8.0mm 10.0mm 12.5mm
(kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m)
26.9 mm 1.23 1.50


33.7 mm 1.56 1.92 2.27

42.4 mm 1.99 2.46 2.91 3.79
48.3 mm 2.28 2.82 3.35 4.37
60.3 mm 2.88 3.56 4.24 5.55 6.82
76.1 mm 3.65 4.54 5.41 7.11 8.77 10.8
88.9 mm 5.33 6.36 8.38 10.4 12.3 12.8
101.6 mm 6.11 7.29 9.63 11.9 14.2 14.8
108 mm 6.50 7.77 10.3 12.7 15.1 15.8
114 mm 6.89 8.23 10.9 13.5 16.0 16.8
127 mm 7.68 9.17 12.1 15.0 17.9 18.8
133 mm 8.05 9.62 12.7 15.8 18.8 19.7
139.7 mm 10.1 13.4 16.6 19.8 20.7 26.0 32.0
152.4 mm 11.1 14.6 18.2 21.7 22.7
159 mm 11.5 15.3 19.0 22.6 23.7 25.9 36.7
168.3 mm 12.2 16.2 20.1 24.0 25.2 31.6 39.0
193.7 mm 18.7 23.3 27.8 29.1 36.6 45.3 55.9
219.1 mm 21.2 26.4 31.5 33.1 41.7 51.6 63.7
244.5 mm 35.3 46.7 57.8 71.5
273 mm 26.5 33.1 39.5 41.4 52.3 64.9 80.3
323.9 mm 39.3 47.0 49.3 62.3 77.4 96.0
 Data sheet SSAB Domex Tube Double Grade 2017-04-25

Square
Height x 2.0mm 2.5mm 3.0mm 4.0mm 5.0mm 6.0mm 7.1mm 8.0mm 8.8mm 10.0mm 12.5mm
Width (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m)
25 x 25 1.36 1.64 1.84
mm
30 x 30 1.68 2.03 2.36
mm
40 x 40 2.31 2.82 3.30 4.20
mm
50 x 50 2.93 3.60 4.25 5.45 6.56
mm
60 x 60 3.56 4.39 5.19 6.71 8.13
mm
70 x 70 5.17 6.13 7.97 9.70
mm
80 x 80 5.96 7.07 9.22 11.3 13.2
mm
90 x 90 6.74 8.01 10.5 12.8 15.1
mm
100 x 7.53 8.96 11.7 14.4 17.0 19.4 21.4
100 mm
110 x 8.31 9.90 13.0 16.0 18.9
110 mm
120 x 10.8 14.3 17.6 20.8 23.8 26.4 31.8
120 mm
140 x 16.8 20.7 24.5 28.3 31.4 34.2 38.1
140 mm
150 x 18.0 22.3 26.4 30.5 34.0 36.9 41.3 48.7
150 mm
160 x 19.3 23.8 28.3 32.7 36.5 39.7 44.4 52.6
160 mm
180 x 27.0 32.1 37.2 41.5 45.2 50.7 60.5
180 mm


200 x 30.1 35.8 41.6 46.5 50.8 57.0 68.3

200 mm
220 x 39.6 46.1 51.5 56.3 63.2 76.2
220 mm
250 x 45.2 52.8 59.1 64.6 72.7 88.0
250 mm
260 x 47.1 55.0 61.6 67.3 75.8 91.9
260 mm
300 x 54.7 63.9 71.6 78.4 88.4 108
300 mm
 Data sheet SSAB Domex Tube Double Grade 2017-04-25

Rectangular
Height x 2.0mm 2.5mm 3.0mm 4.0mm 5.0mm 6.0mm 7.1mm 8.0mm 8.8mm 10.0mm 12.5mm
Width (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m)
40 x 20 1.68 2.03 2.36
mm
40 x 30 1.99 2.42 2.83
mm
50 x 30 2.31 2.82 3.30 4.20
mm
60 x 40 2.93 3.60 4.25 5.45 6.56
mm
70 x 50 3.56 4.39 5.19 6.71 8.13
mm
80 x 40 3.56 4.39 5.19 6.71 8.13
mm
80 x 60 5.17 6.13 7.97 9.70
mm
90 x 50 5.17 6.13 7.97 9.70
mm
100 x 40 5.17 6.13 7.97 9.70
mm
100 x 50 5.6 6.60 8.59 10.5 12.3
mm
100 x 60 5.95 7.07 9.22 11.3 13.2
mm
100 x 80 6.74 8.01 10.5 12.8 15.1
mm
120 x 40 5.96 7.07 9.22 11.3 13.2
mm
120 x 50 6.35 7.54 9.85 12.1 14.2
mm
120 x 60 6.74 8.01 10.5 12.8 15.1
mm


120 x 80 7.53 8.96 11.7 14.4 17.0 19.4 21.4 23.1 25.6
mm
120 x 8.31 9.90 13.0 16.0 18.9
100 mm
140 x 60 8.96 11.7 14.4 17.0
mm
140 x 70 7.92 9.43 12.4 15.2 17.9
mm
140 x 80 9.90 13.0 16.0 18.9
mm
150 x 50 7.53 8.96 11.7 14.4 17.0
mm
150 x 11.3 14.9 18.3 21.7 24.9 27.7 30.0 33.4
100 mm
160 x 70 13.6 16.8 19.8 25.2
mm
160 x 80 14.3 17.6 20.8 23.8 26.4 28.6 31.8
mm
160 x 90 14.9 18.3 21.7 24.9 27.7 30.0
mm
180 x 16.8 20.7 24.5 28.3 31.4 34.2 38.1
100 mm
180 x 18.0 22.3 26.4 30.5 34.0 36.9 41.3 48.7
120 mm
 Data sheet SSAB Domex Tube Double Grade 2017-04-25

Height x 2.0mm 2.5mm 3.0mm 4.0mm 5.0mm 6.0mm 7.1mm 8.0mm 8.8mm 10.0mm 12.5mm
Width (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m) (kg/m)
200 x 80 16.8 20.7 24.5 28.3 31.4 34.2 38.1
mm
200 x 18.0 22.3 26.4 30.5 34.0 36.9 41.3 48.7
100 mm
200 x 23.8 28.3 32.7 36.5 39.7 44.4 52.6
120 mm
220 x 25.4 30.2 35.0 39.0 42.5 47.5
120 mm
250 x 26.18 31.11 40.23 49.11
100 mm
250 x 30.1 35.8 41.6 46.5 50.8 57.0 68.3
150 mm
260 x 35.8 41.6 46.5 50.8 57.0 68.3
140 mm
260 x 39.6 46.1 51.5 56.3 63.2
180 mm
300 x 30.1 35.8 41.6 46.5 50.8 57.0 68.3
100 mm
300 x 40.5 47.2 52.8 64.8 78.1
150 mm
300 x 45.2 52.8 59.1 64.6 72.7 88.0
200 mm
400 x 54.7 63.9 71.6 78.4 88.4 108
200 mm

Mechanical Properties
Grade Thickness Yield Strength Rp0.2 Tensile Strength Rm Elongation A 52) Charpy-V -40°C
(mm) (min MPa) (MPa) (min %) 10x10 mm test speci-
men 1)
(J)
S355J2H 2- 2.99 355 510- 680 20 27


S355J2H 3- 12.5 355 470- 630 20 27

S420MH 2- 12.5 420 500- 660 19 40
Mechanical properties meet or exceed the requirements of EN 10219.
The mechanical properties for rectangular hollow sections are tested by SSAB on the longer side of the cross section.
1)
Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6mm. The specified minimum value corresponds to a full-size specimen.
2)
The hollow sections with D/T < 15 (round) or (B + H)/2T < 12,5 (rectangular and square), the minimum value of elongation is reduced by 2.

Chemical Composition
Grade C Si Mn P S
(max %) (max %) (max %) (max %) (max %)
S355J2H 0.16 0.251) 1.60 0.020 0.012
S420MH 0.16 0.25 1)
1.60 0.020 0.012
Chemical composition meets or exceeds the requirements of EN 10219.
Chemical analyses enables welding in the corner area without restrictions (EN 1993-1-8).
The steel is aluminium-killed.
1) Si content guaranteed at 0.15–0.25 %.

 
Carbon Equivalent Values

CEV 0.39
(max %)
CEV value exceeds the requirements of EN 10219.
 Data sheet SSAB Domex Tube Double Grade 2017-04-25

Tolerances
 
Characteristic Circular hollow sections
Tolerances meet or exceed the requirements of EN 10219
Outside diameter (D) 1) ±1%, however a minimum of ±0.5 mm and a maximum of ±10 mm
Out-of-roundness 2%, when D/T ≤ 100
Thickness (T) When D ≤ 323.9 mm: -5%/+10%, with a minimum of ±0.2 mm and
maximum ±0.5 mm
When 355.6 ≤ D ≤ 406.4 mm3): ±10%, when T ≤ 5 mm / ±0.5 mm,
when T > 5 mm
When D > 406.4 mm3): ±10%, with a maximum of ±2 mm
Straightness 0.20% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000- 18000 mm (standard lengths 6000 &
12000 mm)

Exact length Agreed at the time of enquiry and order

1)
All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.
 
Characteristic Square hollow sections
Tolerances meet or exceed the requirements of EN 10219
Outside dimensions (B, H) 1) When B, H < 100 mm ±1 % minimum ±0.5 mm
When 100 mm ≤ B, H ≤ 200 mm: ±0.8%
When B, H > 200 mm: ±0.6%
-5%/ +10 %, with a minimum of ±0.2 mm and maximum ±0.5 mm


Thickness (T)
External corner profile When T ≤ 6 mm: 1.6 x T–2.4 x T
When 6 mm < T ≤ 10 mm: 2.0 x T-3.0 x T
When T > 10 mm: 2.4 x T–3.6 x T
Squareness of side 90° ±1°
Concavity/convexity 0.8%, with a minimum of 0.5 mm
Twist 2 mm + 0.5 mm/m
Straightness 0.15% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000- 18000 mm (standard lengths 6000 &
12000 mm)

Exact length Agreed at the time of enquiry and order

1)
All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.
 
 Data sheet SSAB Domex Tube Double Grade 2017-04-25

Characteristic Rectangular hollow sections

Tolerances meet or exceed the requirements of EN 10219
Outside dimensions (B, H) 1) When B, H < 100 mm ±1 % minimum ±0.5 mm
When 100 mm ≤ B, H ≤ 200 mm: ±0.8%
When B, H > 200 mm: ±0.6%
Thickness (T) -5%/ +10 %, with a minimum of ±0.2 mm and maximum ±0.5 mm
External corner profile When T ≤ 6 mm: 1.6 x T–2.4 x T
When 6 mm < T ≤ 10 mm: 2.0 x T-3.0 x T
When T > 10 mm: 2.4 x T–3.6 x T
Squareness of side 90° ±1°
Concavity/convexity 0.8%, with a minimum of 0.5 mm
Twist 2 mm + 0.5 mm/m
Straightness 0.15% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000- 18000 mm (standard lengths 6000 &
12000 mm)

Exact length Agreed at the time of enquiry and order

1)
All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.

Contact Information
www.ssab.com/contact


The English version of this document shall prevail in case of discrepancy. Download the latest version of this document at www.ssab.com
SSAB, Strenx, Hardox, Docol, GreenCoat, Toolox, Armox, Ramor, Domex, Laser, Raex, Duroxite are trademarks owned by the SSAB group of companies.