This document outlines various repair and maintenance services for a vessel including:
1) Docking and undocking services from December 27, 2015 to January 05, 2016 including blocks and line handlers.
2) Hull preservation work such as scraping, grit sandblasting, and painting of the hull from the keel to the bulwarks.
3) Plate repairs including replacing deteriorated shell platings, installing doublers, and crop-out and installation of zinc anodes.
This document outlines various repair and maintenance services for a vessel including:
1) Docking and undocking services from December 27, 2015 to January 05, 2016 including blocks and line handlers.
2) Hull preservation work such as scraping, grit sandblasting, and painting of the hull from the keel to the bulwarks.
3) Plate repairs including replacing deteriorated shell platings, installing doublers, and crop-out and installation of zinc anodes.
This document outlines various repair and maintenance services for a vessel including:
1) Docking and undocking services from December 27, 2015 to January 05, 2016 including blocks and line handlers.
2) Hull preservation work such as scraping, grit sandblasting, and painting of the hull from the keel to the bulwarks.
3) Plate repairs including replacing deteriorated shell platings, installing doublers, and crop-out and installation of zinc anodes.
This document outlines various repair and maintenance services for a vessel including:
1) Docking and undocking services from December 27, 2015 to January 05, 2016 including blocks and line handlers.
2) Hull preservation work such as scraping, grit sandblasting, and painting of the hull from the keel to the bulwarks.
3) Plate repairs including replacing deteriorated shell platings, installing doublers, and crop-out and installation of zinc anodes.
Download as XLS, PDF, TXT or read online from Scribd
Download as xls, pdf, or txt
You are on page 1/ 10
A DOCKING & UNDOCKING SERVICES :
A-1 Docking and undocking, including first day rental.
Dock rentals of each subsequent laydays. A-2 Dock in : December 27, 2015 Dock out : January 05, 2016 A-3 Preparation of Blocks : a. Erection of center blocks for proper docking. b. Erection of side blocks for proper docking and shoring. A-4 Line handlers for mooring and unmooring during docking/undocking. Wharfage fee during stay of vessel along side of wharf after A-5 dry-docking for completion of all repair works.
B HULL PRESERVATION WORKS :
B-1 Scraping of tenacious marine growth and barnacles from keel to LWL. Jetwashing with high pressured fresh water to remove salts deposit B-2 and other marine contaminants from keel to DLL. B-3 Grit sandblasting of entire hull to the following : a. Keel to DLL Spotblasting 40% Sweepblasting 60% b. DLL to bulwark top Spotblasting 40% Sweepblasting 60%
B HULL PRESERVATION WORKS :
B-4 Jetwashing with low pressured fresh water prior to 2nd coat painting. Airless spray painting of gritblasted hull using owner supplied B-5 CHUGOKU paints with the following schedules : a. Keel to DLL applied one ( 1 ) touch-up coat of super bondex gray paint applied one ( 1 ) full coats of epicon marine hb-al paint applied two ( 2 ) full coats of seagrand prix anti-fouling mark paint b. DLL to bulwark top applied one ( 1 ) touch-up coat of super bondex gray paint applied one ( 1 ) full coat of super bondex gray paint applied one ( 1 ) full coat of epoxy enamel white paint B-6 Covering of hull anodes with tapes prior to painting and peeled-off. B-7 Painting of draft marks at port and stbd side. Painting of port of registry. B-8 Staging inway of hull cleaning and painting.
C PLATES & SECTIONS :
C-1 Crop-out and replate deteriorated forward side shell platings. @ frame # 67-68 S 01 pc 9 mm x 0.42 mx 0.70 m ms plate @ frame # 64-67 P 01 pc 9 mm x 0.40 mx 2.06 m ms plate a. Steel weight installed less than 300 kgs 50% b. Plates with single curvature 10% C-2 Installation of doubler plate port side. ### 01 pc 9 mm x 0.40 mx 0.98 m frame # 55- 56 ### 01 pc 9 mm x 0.32 mx 0.32 m frame # 48-49 C-3 Installation of doubler plate stbd. side. 30 ### 01 pc 6 mm x 2.26 mx 0.94 m frame # 17- 20 C-4 Installation of bulwark top plates @ port side. ### 01 pc 9 mm x 2.00 mx 0.20 m ms plate a. Steel weight installed less than 300 kgs 50% C-5 Build up pin holes . C-6 Crop-out and installation of welded type zinc anodes 8.5 kgs. 44-38-04-40-42-46
322838224043
D RUDDER, PROPELLER & SHAFT WORKS :
D-1 RUDDER WORKS : a. Removal and reinstallation of jumping collar. b. Checked clearances of upper neck, lower neck and puntle bearings and submiited results to Owner's Representative. c. Installation of lifting padeye. d. Disconnection and reconnection of steering gear from stock. e. Pull-out of rudder stock inway to renew upper and lower bearing and install after. f. Pull-out of pintle bearing inway for renewal. g. Removal and reinstallation of rudder blade inway to pull-out and reinstall propeller and tailshaft. D-2 PROPELLER WORKS : a. Removal and reinstallation of D = 67 inches x P = 42 inches x four ( 4 ) bladed propeller.
D RUDDER, PROPELLER & SHAFT WORKS :
D-2 PROPELLER WORKS : b. Reconditioning of bronze propeller size 67" diameter x 42" pitch x 4 blade right hand rotation, such as straightening bent blades, alignment on trailing and leading edges from 3R to tip, equal blade spacing balancing and polishing. D-3 TAILSHAFT WORKS : a. Checked clearances of inboard and outboard bearings and submiited results to Owner's Representative. c. Slackened coupling bolts, disconnected coupling from shaft, draw- out and reinstallation of 4 inØ water lubricated tailshaft. d. Checking straightness and polishing of tailshaft on workshop. e. Removed worn-out inboard and outboard bearings and installed newly machined magkuno wood bearings. f. Repacking of stuffing box gland. D-4 Lifting of propeller and tailshaft ( pull-out and install ) Hauling of propeller and tailshaft to workshop for repair and returned D-5 back later after completion. D-6 Staging inway of propulsion works.
D RUDDER, PROPELLER & SHAFT WORKS :
D-7 Sea Valves and Sea Chests : a. Removal of gratings of sea chests, cleaning of inner surfaces, blasting, painting with A/C & A/F and refitting. b. Disconnected, removed valves from sea chest and later reinstalled. c. Opening of sea valves for inspection, cleaning, grinding, blasting, valve seat lapping, painting with A/C and repacking. 5K 100 Angle Valve 5K 80 Angle Valve 5K 50 Angle Valve 5K 40 Angle Valve 5K 25 Angle Valve Conducted onboard sea trial to determine satisfactory of completed D-8 propulsion works and main engine alignment.
E MACHINING WORKS : E-1 Alignment of bended portions of tailshaft by machine pressed. Reface from outboard to inboard and fibering packing portion of E-2 tailshaft. Fabricate rudder pin sleeve using material manganese bronze E-3 6" diam. X 140 mm Machining of tailshaft bearings using magkuno wood : E-4 Inboard : OD = 239.3 mm ID = 193 mm L = 8inches Outboard : OD = 240.1 mm ID = 197.2 mm L = 725 mm Materials magkunu wood by yard supply. E-5 11" diam. X 3 ft 11" diam. X 2 ft
28.543307
F GENERAL SERVICES : F-1 HULL GAUGING : a. Conducted hammer testing on entire hull below H2O line for utg testing. b. Conducted UTG testing on marked suspected areas of entire hull. c. Provision of new shell expansion plan in absence of reference plan. d. Furnished CAD drawing of shell expansion plan and indicated updated readings taken from utg testing. e. Provision of CAD drawing for new docking plan . F-2 Shore Power : a. Line connection and disconnection. b. Supply of power onboard during repair works. F-3 Fire Watchman and Security Watchman : a. Fire watchman during the entire duration of repair. b. Security watchman during the entire duration of repair. F-4 Daily galley garbage during the entire duration of repair. Conducted megger test on all motors and panel boards and submitted F-5 insulation resistance report to OR as per MARINA requirements.
A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder
A Guide to Motor Boat Design and Construction - A Collection of Historical Articles Containing Information on the Methods and Equipment of the Boat Builder
