CONTROLS

A Division of BRAY INTERNATIONAL, Inc.

Bray/McCannalok Butterfly Valves

Technical Manual

TM1023 - 12/03/2009
Bray/McCannalok
Butterfly Valves
Technical Manual - Table of Contents
Topic Page(s)

Seating & Unseating Torques..........................3

Imperial (Lb-Ins)................................................4-6

Metric (N-m).....................................................7-9

Dynamic Torque.................................................10-13

Valve Sizing Coefficients...............................14

Imperial (Cv).....................................................15-16

Metric (Kv)........................................................17-18

Pressure & Temperature Rating (ºF & ºC)

With PTFE Seats................................................19

With RTFE Seats................................................20

Flange Bolting Guide........................................21

Series 40/41/4A - ASME 150.............................22-23

Series 42/43/4B - ASME 300.............................24-25

Series 44/45 - ASME 600...................................26

All statements, technical information, and recom-

mendations in this bulletin are for general use only.
Consult Bray representatives or factory for the specific
requirements and material selection for your intended
application. The right to change or modify product
design or product without prior notice is reserved.
 Bray/McCannalok HPBV – Seating & Unseating Torques

Seating & Unseating Torques:

Valve orientation to the flow of media affects the torque.
Torque values are presented in two categories:

FLOW FLOW

Seat Retainer Seat Retainer

UPSTREAM DOWNSTREAM

FLOW FLOW

Seat Retainer Seat Retainer

UPSTREAM DOWNSTREAM

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 3 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 150 - Torques (Lb-Ins)

Series 40/41/4A Standard - Valve Differential Pressure (PSIG)
Valve Less than 150 psig >150-200 psig >200-250 psig >250-285 psig
Size
Inches Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
2.5 170 200 190 240 210 280 215 300
3 185 220 210 260 225 300 230 320
4 275 320 300 370 315 420 320 460
5 550 650 640 800 705 940 730 1,040
6 690 810 770 960 825 1,100 840 1,200
8 1,280 1,500 1,400 1,700 1,500 1,950 1,570 2,100
10 2,400 2,800 3,640 3,300 2,820 3,760 2,870 4,100
12 3,500 4,100 4,000 5,000 4,400 5,900 4,550 6,500
14 5,400 6,300 5,920 7,400 6,400 8,500 6,650 9,500
16 7,700 9,100 9,040 11,300 10,100 13,500 10,500 15,000
18 11,900 14,000 13,600 17,000 15,000 20,000 15,400 22,000
20 15,300 18,000 17,100 21,300 18,500 24,700 18,900 27,000
24 24,650 29,000 27,680 34,600 30,000 40,100 30,800 44,000
26 24,650 29,000 27,680 34,600 30,000 40,100 30,800 44,000
28 34,850 41,000 37,600 47,000 44,300 59,200 44,500 63,500
30 39,950 47,000 42,960 53,700 50,800 67,700 52,500 75,000
32 45,000 53,000 48,800 61,000 57,600 76,800 58,800 84,000
34 45,000 53,000 48,800 61,000 57,600 76,800 58,800 84,000
36 54,000 64,000 64,800 81,000 73,500 98,000 77,000 110,000
40 62,000 73,000 73,600 92,000 82,500 110,000 84,700 121,000
42 71,000 83,000 84,000 105,000 95,250 127,000 101,000 143,000
48 98,000 115,000 121,600 152,000 142,500 190,000 151,900 217,000
54 136,000 160,000 169,600 212,000 198,000 265,000 211,400 302,000
60 Please Consult Factory

Series 40/41 Fire Safe - Valve Differential Pressure (PSIG)

2.5 680 720 690 770 700 810 710 840
3 750 800 760 830 770 870 780 900
4 850 900 880 980 890 1,050 910 1,100
5 1,420 1,500 1,470 1,630 1,500 1,750 1,600 1,850
6 1,660 1,750 1,690 1,880 1,800 2,000 1,900 2,100
8 2,600 2,800 2,690 2,950 2,750 3,100 2,860 3,200
10 3,900 4,200 4,100 4,530 4,250 4,860 4,400 5,100
12 6,500 6,900 6,600 7,350 6,700 7,790 6,900 8,100
14 12,300 13,000 12,600 14,000 13,200 15,500 13,600 17,000
16 15,200 16,000 15,800 17,600 16,300 19,200 16,320 20,400
18 18,000 19,000 18,900 21,000 19,000 22,500 19,200 24,000
20 21,800 23,000 22,500 25,000 23,800 28,000 28,800 36,000
24 31,000 33,000 34,200 38,000 37,400 44,000 50,400 63,000
26 Please Consult Factory
28 Please Consult Factory
30 Please Consult Factory
32 Please Consult Factory
34 Please Consult Factory
36 Please Consult Factory
40 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 4 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 300 - Torques (Lb-Ins)

Series 42/43/4B Standard - Valve Differential Pressure (PSIG)
Valve Less than 150 psig >150-350 psig >350-550 psig >550-740 psig
Size
Inches Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
2.5 170 200 290 360 380 510 470 670
3 185 220 310 380 400 530 490 690
4 270 320 420 530 550 730 700 1,000
5 550 650 1,000 1,250 1,390 1,850 1,800 2,550
6 850 1,000 1,320 1,650 1,720 2,300 2,100 3,000
8 1,580 1,850 2,480 3,100 3,230 4,300 3,700 5,300
10 2,800 3,300 4,400 5,500 5,700 7,600 7,000 10,000
12 4,250 5,000 6,640 8,300 8,630 11,500 10,500 15,000
14 7,300 8,600 10,720 13,400 13,700 18,300 15,400 22,000
16 11,900 14,000 17,200 21,500 21,800 29,000 26,600 38,000
18 15,300 18,000 21,600 27,000 27,100 36,100 31,500 45,000
20 20,400 24,000 29,400 36,700 37,000 49,300 42,700 61,000
24 32,300 38,000 45,600 57,000 57,500 76,700 66,500 95,000
30 68,000 80,000 101,600 127,000 129,000 172,000 147,000 210,000
36 101,150 119,000 144,000 180,000 180,000 240,000 203,000 290,000
40 115,600 136,000 168,000 210,000 222,000 296,000 278,600 398,000
48 127,500 150,000 217,600 272,000 321,000 428,000 403,200 576,000
54 Please Consult Factory

Series 42/43 Fire Safe - Valve Differential Pressure (PSIG)

2.5 680 720 775 860 860 1,010 880 1,100
3 750 800 855 950 935 1,100 960 1,200
4 850 900 1,080 1,200 1,275 1,500 1,360 1,700
5 1,420 1,500 2,070 2,300 2,635 3,100 2,880 3,600
6 2,000 2,100 2,610 2,900 3,150 3,700 3,440 4,300
8 3,000 3,150 3,870 4,300 4,675 5,500 4,960 6,200
10 6,900 7,300 9,180 10,200 11,050 13,000 12,000 15,000
12 10,450 11,000 13,200 14,700 15,640 18,400 16,800 21,000
14 18,050 19,000 21,600 24,000 22,100 26,000 22,400 28,000
16 26,600 28,000 34,200 38,000 37,400 44,000 39,200 49,000
18 Please Consult Factory
20 Please Consult Factory
24 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 5 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 600 - Torques (Lb-Ins)

Series 44/45 Standard - Valve Differential Pressure (PSIG)
Valve Less than 150 psig >150-600 psig >600-1050 psig >1050-1480 psig
Size
Inches Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
3 400 480 700 870 900 1,200 1,000 1,450
4 850 960 1,280 1,600 1,580 2,100 1,900 2,700
6 1,450 1,700 2,560 3,200 3,450 4,600 4,100 5,800
8 3,500 4,100 5,760 7,200 7,600 10,100 9,800 14,000
10 7,100 8,300 9,600 12,000 13,500 18,000 16,800 24,000
12 10,100 11,800 11,200 14,000 19,500 26,000 21,000 30,000
14 11,900 14,000 19,200 24,000 24,800 33,000 30,000 43,000
16 14,000 16,500 28,400 35,500 34,500 46,000 45,500 65,000
18 16,200 19,000 34,400 43,000 49,000 65,000 64,400 92,000
20 21,300 25,000 45,600 57,000 66,000 88,000 87,000 124,000
24 33,000 39,000 71,000 89,000 94,000 125,000 123,000 175,000
30 71,000 83,000 137,000 172,000 180,000 240,000 217,000 310,000
Series 44/45 Fire Safe - Valve Differential Pressure (PSIG)
3 Please Consult Factory
4 Please Consult Factory
6 Please Consult Factory
8 Please Consult Factory
10 Please Consult Factory
12 Please Consult Factory
14 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 6 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 150 - Torques (N-m)

Series 40/41/4A Standard - Valve Differential Pressure (Bar)
Valve Less than 10.3 Bar >10.3-14 Bar >14-17.2 Bar >17.2-20 Bar
Size
mm Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
65 19 23 21 27 24 32 24 34
80 21 25 24 29 25 34 26 36
100 31 36 34 42 36 47 36 52
125 62 73 72 90 80 106 82 118
150 78 92 87 108 93 124 95 136
200 145 170 158 192 170 220 177 237
250 271 316 411 373 319 425 324 463
300 396 463 452 565 497 667 514 735
350 610 712 669 836 723 961 751 1,074
400 870 1,028 1,022 1,277 1,141 1,526 1,187 1,695
450 1,345 1,582 1,537 1,921 1,695 2,260 1,740 2,486
500 1,729 2,034 1,932 2,407 2,091 2,791 2,136 3,051
600 2,785 3,277 3,128 3,910 3,390 4,531 3,480 4,972
650 2,785 3,277 3,128 3,910 3,390 4,531 3,480 4,972
700 3,938 4,633 4,249 5,311 5,006 6,690 5,029 7,176
750 4,514 5,311 4,854 6,068 5,740 7,650 5,933 8,475
800 5,085 5,989 5,514 6,893 6,509 8,678 6,644 9,492
850 5,085 5,989 5,514 6,893 6,509 8,678 6,644 9,492
900 6,102 7,232 7,322 9,153 8,306 11,074 8,701 12,430
1,000 7,006 8,249 8,317 10,396 9,323 12,430 9,571 13,673
1,050 8,023 9,379 9,492 11,865 10,763 14,351 11,413 16,159
1,200 11,074 12,995 13,741 17,176 16,103 21,470 17,165 24,521
1,350 15,368 18,080 19,165 23,956 22,374 29,945 23,888 34,126
1,500 Please Consult Factory

Series 40/41 Fire Safe - Valve Differential Pressure (Bar)

65 77 81 78 87 79 92 80 95
80 85 90 86 94 87 98 88 102
100 96 102 99 111 101 119 103 124
125 160 170 166 184 170 198 181 209
150 188 198 191 212 203 226 215 237
200 294 316 304 333 311 350 323 362
250 441 475 463 512 480 549 497 576
300 735 780 746 831 757 880 780 915
350 1,390 1,469 1,424 1,582 1,492 1,752 1,537 1,921
400 1,718 1,808 1,785 1,989 1,842 2,170 1,844 2,305
450 2,034 2,147 2,136 2,373 2,147 2,543 2,170 2,712
500 2,463 2,599 2,543 2,825 2,689 3,164 3,254 4,068
600 3,503 3,729 3,865 4,294 4,226 4,972 5,695 7,119
650 Please Consult Factory
700 Please Consult Factory
750 Please Consult Factory
800 Please Consult Factory
850 Please Consult Factory
900 Please Consult Factory
1,000 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 7 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 300 - Torques (N-m)

Series 42/43/4B Standard - Valve Differential Pressure (Bar)
Valve Less than 10.3 Bar >10.3-24 Bar >24-38 Bar >38-51 Bar
Size
mm Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
65 19 23 33 41 43 58 53 76
80 21 25 35 43 45 60 55 78
100 31 36 47 60 62 82 79 113
125 62 73 113 141 157 209 203 288
150 96 113 149 186 194 260 237 339
200 179 209 280 350 365 486 418 599
250 316 373 497 622 644 859 791 1,130
300 480 565 750 938 975 1,300 1,187 1,695
350 825 972 1,211 1,514 1,548 2,068 1,740 2,486
400 1,345 1,582 1,944 2,430 2,463 3,277 3,006 4,294
450 1,729 2,034 2,441 3,051 3,062 4,079 3,560 5,085
500 2,305 2,712 3,322 4,147 4,181 5,571 4,825 6,893
600 3,650 4,294 5,153 6,441 6,498 8,667 7,515 10,735
750 7,684 9,040 11,481 14,351 14,577 19,436 16,611 23,730
900 11,430 13,447 16,272 20,340 20,340 27,120 22,939 32,770
1,000 13,063 15,368 18,984 23,730 25,086 33,448 31,482 44,974
1,200 14,408 16,950 24,589 30,736 36,273 48,364 45,562 65,088
1,350 Please Consult Factory
Series 42/43 Fire Safe - Valve Differential Pressure (Bar)
65 77 81 88 97 97 114 99 124
80 85 90 97 107 106 124 108 136
100 96 102 122 136 144 170 154 192
125 160 170 234 260 298 350 325 407
150 226 237 295 328 356 418 389 486
200 339 356 437 486 528 622 560 701
250 780 825 1,037 1,153 1,249 1,469 1,356 1,695
300 1,181 1,243 1,492 1,661 1,767 2,079 1,898 2,373
350 2,040 2,147 2,441 2,712 2,497 2,938 2,531 3,164
400 3,006 3,164 3,865 4,294 4,226 4,972 4,430 5,537
450 Please Consult Factory
500 Please Consult Factory
600 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 8 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Seating & Unseating Torques

ASME 600 - Torques (N-m)

Series 44/45 Standard - Valve Differential Pressure (Bar)
Valve Less than 10.3 Bar >10.3-41.4 Bar >41.4-72.4 Bar >72.4-102 Bar
Size
mm Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream Retainer Upstream Retainer Downstream
80 45 54 79 98 102 136 113 164
100 96 108 145 181 179 237 215 305
150 164 192 289 362 390 520 463 655
200 396 463 651 814 859 1,141 1,107 1,582
250 802 938 1,085 1,356 1,526 2,034 1,898 2,712
300 1,141 1,333 1,266 1,582 2,204 2,938 2,373 3,390
350 1,345 1,582 2,170 2,712 2,802 3,729 3,390 4,859
400 1,582 1,865 3,209 4,012 3,899 5,198 5,142 7,345
450 1,831 2,147 3,887 4,859 5,537 7,345 7,277 10,396
500 2,407 2,825 5,153 6,441 7,458 9,944 9,831 14,012
600 3,729 4,407 8,023 10,057 10,622 14,125 13,899 19,775
750 8,023 9,379 15,481 19,436 20,340 27,120 24,521 35,030

Series 44/45 Fire Safe - Valve Differential Pressure (Bar)

80 Please Consult Factory
100 Please Consult Factory
150 Please Consult Factory
200 Please Consult Factory
250 Please Consult Factory
300 Please Consult Factory
350 Please Consult Factory

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Torque : 9 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Dynamic Torques

Dynamic Torques:
When a media flows through a butterfly valve, static pressure Estimating Dynamic Torque
does not act uniformly on the surfaces of the valve disc. Dynamic Dynamic torque can be estimated using the following
torque will cause rotary motion when unchecked by the actuator
or manual operator possibly resulting in opening or closing of the empirical equations:
valve. If the dynamic torque is of a magnitude that is greater than
the bearing and packing friction torque and there is no actuator Liquid Flow:
in place to maintain disc position, the opening or closing action Imperial....... Td (Lb-inches) = Ct D³ p
could result in injury to operating personnel or an interruption of
the process. Sudden closure (slamming) can cause water hammer
Metric.......... Td (N-m) = .0001 Ct D³ p
damage in lines carrying liquid.
Gas Flow:
In high performance butterfly valves which have the disc Imperial....... Td (Lb-inches) = Ct D³ Y p
offset from the stem and have non-symmetrical disc faces, Metric.......... Td (N-m) = .0001 Ct D³ Y p
dynamic torque acts to close the valve if the valve is installed with
the seat retainer downstream,Pressure Distribution
but can act to close or open the
valve, depending on the position of the disc, if the seat retainer Dynamic Torque - Terminology
is upstream.
Ct - dynamic torque coefficient (see graphs and tables on
Seat Retainer Upstream the pg. 10 for values of Ct.) Positive value of Ct means
that the dynamic torque acts to close the valve and a
negative value of Ct to open the valve.

FLOW D - nominal valve size (inch or mm)

Fk - ratio of specific heat factor (dimensionless)
Fk = k/1.40 or Fk = 1 for air
k- ratio of specific heat (dimensionless)
p - effective pressure drop across the valve (psi or bar)
Seat Retainer Downstream
p1 - valve inlet pressure (psia or bar abs.)
Td - dynamic torque (Lb-inches or N-m)

FLOW x- x = p/p1
Y- gas expansion factor (dimensionless)
Y = 1 – x / (3 Fk xt)
xt - gas critical pressure ratio (dimensionless)
Dynamic torque should be calculated as part of the valve actua- Values of xt change with disc position and are identi-
tor sizing procedure or to determine if hand lever operation is ac- cal for seat retainer upstream and downstream.
ceptable. In this regard, the total torque of all service conditions
must be considered. º Open xt º Open xt
The total torque when the disc is in the seat consists of: 10º 0.46 55° 0.31
1. Seating torque 15º 0.46 60° 0.28
2. Stem packing torque
3. Eccentricity torque 20º 0.46 65° 0.27
4. Stem bearing torque 25° 0.45 70° 0.25
The total torque when the disc is in the seat is published as seat-
30° 0.44 75° 0.24
ing/unseating torque. When the disc is out of the seat, the total
torque consists of dynamic torque, stem packing torque, and stem 35° 0.42 80° 0.22
bearing torque. 40° 0.39 85° 0.21
Total torque changes with the disc position. Maximum total 45° 0.35 90º 0.19
torque can occur at shutoff (disc in the seat), at breakaway (mo- 50° 0.33
tion initiation), or at any open disc position where the product of
valve pressure drop and dynamic torque coefficient peaks in com-
bination with prevailing bearing and packing torque.

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Dynamic : 10 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Dynamic Torques

For: Condition: Use: Note:

Pipe and • Nominal Valve Size
Valve Size • Valve Pressure Drop
Equal • Ct from graphs/tables on pg. 12
Subchoked
Flow • Nominal Valve Size
• Ct from graphs/tables on pg. 12
W/ Pipe
• Valve Pressure Drop as if valve
Reducers
were installed in valve-sized
pipe with same flow rate

If actual pressure drop at the choked condition is

• Nominal Valve Size not known, estimate by evaluating the pressure in
Pipe and
• Ct from graphs/tables on pg. 12 the piping at the valve outlet needed to sustain the
Valve Size
• Actual Pressure drop through choked flow rate through the piping downstream
Equal
valve. of the valve; then subtracting it from the valve inlet
pressure.

Choked Flow If the pressure drop at the choked condition is

not known, estimate the line pressure just down-
• Nominal Valve Size stream of the valve/reducer assembly which is
W/ Pipe • Ct from graphs/tables on pg. 12 needed to sustain the choked flow rate of the
Reducers • Actual pressure drop through valve/reducer assembly through the downstream
valve/reducer assembly. piping; then subtract this pressure from the line
pressure just ahead of the valve/reducer assembly,
to get the actual pressure drop.

For: Condition: Use: Note:

Pipe and • Nominal Valve Size
Valve Size • Valve Pressure Drop
Equal • Ct from graphs/tables on pg. 12
Subchoked
Flow • Nominal Valve Size
• Ct from graphs/tables on pg. 12 In calculating Y, use the line pressure
W/ Pipe
• Valve Pressure Drop (and expansion factor just upstream of the inlet reducer for p1
Reducers
Y) as if valve were installed in valve-sized and xt from the table on page 10.
pipe with same flow rate.

• Nominal Valve Size

Pipe and • Gas expansion factor Y of 2/3
Valve Size • Ct from graphs/tables on pg. 12 Use xt from the table on page 10.
Equal
• p = p1 Fk xt
Choked Flow
• Nominal Valve Size Use the line pressure just upstream
W/ Pipe • Gas expansion factor Y of 2/3 of the inlet reducer for p1 and xt from
Reducers • Ct from graphs/tables on pg. 12 the table above in calculating p,
• p = p1 Fk xt on page 10.

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Dynamic : 11 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Dynamic Torques

Figure 3. Ct values with the Seat Retainer Down Stream

McCannalok Dynamic Torque Coefficient
Seat Retainer Downstream
.055
Dynamic Torque Coefficient

0.5
0.45
.04
0.35
.03
0.25
.02
0.15
.01
0.05
.0
Angle of Opening 0˚ 10˚ 15˚ 20˚ 25˚ 30˚ 35˚ 40˚ 45˚ 50˚ 55˚ 60˚ 65˚ 70˚ 75˚ 80˚ 85˚ 90˚
Ct Down .0 .012 .022 .031 .044 .058 .073 .088 .114 .141 .176 .212 .260 .308 .370 .431 .496 .362

Figure 4. Ct values with the Seat Retainer Up Stream

McCannalok Dynamic Torque Coefficient
Seat Retainer Upstream
.015
0.1
Dynamic Torque Coefficient

0.05
.0 !
-0.05
-0.1
-0.15
-0.2
-0.25
-0.3
-0.35
-0.4
Angle of Opening 0˚ 10˚ 15˚ 20˚ 25˚ 30˚ 35˚ 40˚ 45˚ 50˚ 55˚ 60˚ 65˚ 70˚ 75˚ 80˚ 85˚ 90˚
Ct up .0 .015 .018 .020 .023 .027 .037 .046 .055 .063 .078 .086 .093 .100 .084 .032 -.17 -.37

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Dynamic : 12 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Dynamic Torques

1. Subchoked Liquid Flow, Line-size Valve.

Example Calculations: Data:
A 24” class 150 McCannalok is to be installed in a 24” • 75 psi with the valve 20 degrees open
line carrying water. It has been determined that the flow • 70 psi with the valve 30 degrees open
is not choked and the following pressure drops through • 35 psi with the valve 40 degrees open
the valve have been calculated: • 3.5 psi with the valve 55 degrees open
• 1.1 psi with the valve 60 degrees open
• .20 psi with the valve 70 degrees open
• .05 psi with the valve 80 degrees open
• .03 psi with the valve 90 degrees open
Estimate the maximum dynamic torque in Lb-inches for the valve Td = Ct D³ p
considering installation with the seat retainer upstream.
Substituting produces following results: • 20 degrees, Td = .020 x 24³ x 75 = 20,700 Lb-inches,
(tends to close the valve)
• 30 degrees, Td = .027 x 24³ x 70 = 26,100 Lb-inches
• 40 degrees, Td = .046 x 24³ x 35 = 22,300 Lb-inches
• 55 degrees, Td = .078 x 24³ x 3.5 = 3,800 Lb-inches
• 60 degrees, Td = .086 x 24³ x 1.1 = 1,300 Lb-inches
• 70 degrees, Td = .100 x 24³ x .20 = 300 Lb-inches
• 80 degrees, Td = .032 x 24³ x .05 = 20 Lb-inches
• 90 degrees, Td = -.369 x 24³ x .03 = -150 Lb-inches,
(tends to open the valve)
Thus the peak dynamic torque will occur between 30 and 40 degrees open.
Verify dynamic torque at 35 degrees: Approximate pressure drop = (70+35)/2 = 52.5 psi.
At 35 degrees: Td = .037 x 24³ x 52.5 = 27,000 Lb-inches
The peak dynamic torque of approximately 27,000 Lb-inches occurs at about 35 degrees open.
When sizing the valve operator, total torque must be considered. The total torque when the disc is in the seat con-
sists of seating torque, stem packing torque, eccentricity torque and stem bearing torque. The total torque when
the disc is in the seat is published as seating/unseating torque (see pages 1-6. When the disc is out of the seat, total
torque consists of dynamic torque, stem packing torque, and stem bearing torque.

2. Choked Gas Flow, Reduced-size Valve.

Example Calculations:
20” (DN 500) class 300 McCannalok butterfly valve is installed in a 600 mm (24”) line flowing air and the disc is
set at 45 degrees. The flow is choked. A pressure gauge tapped into the pipe just above the upstream reducer shows
24.5 bar.
Estimate the dynamic torque in N-m, given that the seat D = 500 mm
retainer is installed downstream. Fk = 1.0
Ct = .114
Y = .667 for choked flow
p1 = 24.5 + 1.0 = 25.5 bar absolute, (1 atm. = 1.013
bar, i.e. about 1.0 bar)
xt at 45º = .35
Calculations:
p = p1 Fk xt Td = .0001 Ct D³ Y p
p = 25.5 x 1.0 x .35 = 8.9 bar Td = .0001 x .114 x 500³ x .667 x 8.9 = 8,500 N-m
Thus the dynamic torque at 45º open is about 8,500 N-m, and acts to close the valve.

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Dynamic : 13 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Valve Sizing Coefficients

Valve Sizing Coefficients:

1. Valve Sizing Coefficients (Cv). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 15-16
1. Cv stands for Valve Sizing Coefficient.
2. Cv varies with the valve size, angle of opening and the manufacturer’s valve style.
3. Cv is defined as the volume of water in USGPM that will flow through a given restriction or valve
opening with a pressure drop of one (1) psi at room temperature.

2. Valve Sizing Coefficients (Kv). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 17-18

1. Kv stands for Valve Sizing Coefficient.
2. Kv varies with the valve size, angle of opening and the manufacturer’s valve style.
3. Kv is defined as the volume of water in Cubic Meters/Hour (m3/hr) that will flow through a given
restriction or valve opening with a pressure drop of one (1) bar at room temperature.

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Coefficients : 14 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Valve Sizing Coefficients

ASME 150 Series 40/41/4A - Valve Sizing Coefficient (Cv)

Valve Disc Position (Degrees)
Size
Inches 90º 80º 70º 60º 50º 40º 30º 20º 10º
2 1/2 160 136 100 78 50 30 16 8 3
3 185 178 155 123 87 56 32 14 5
4 375 365 315 250 175 115 63 31 10
5 790 675 500 360 238 146 78 41 16
6 1,350 1,070 750 510 330 218 140 81 35
8 2,800 2,230 1,590 1,060 685 456 280 165 65
10 4,300 3,450 2,430 1,630 1,050 700 450 250 100
12 6,650 5,330 3,750 2,530 1,630 1,080 700 390 155
14 7,650 6,100 4,300 2,900 1,890 1,250 810 450 175
16 9,800 7,860 5,510 3,700 2,420 1,530 1,020 580 230
18 10,500 9,100 6,960 5,100 3,520 2,220 1,180 500 170
20 13,500 11,700 8,800 6,500 4,500 2,820 1,530 640 200
24 20,000 17,100 12,800 9,570 6,640 3,880 2,200 920 240
26 20,000 17,100 12,800 9,570 6,640 3,880 2,200 920 240
28 28,000 23,900 18,200 13,500 9,300 5,700 3,100 1,300 290
30 32,000 27,300 20,900 15,500 10,700 6,700 3,600 1,510 320
32 34,000 29,100 22,300 16,500 11,400 7,150 3,850 1,610 340
34 34,000 29,100 22,300 16,500 11,400 7,150 3,850 1,610 340
36 48,500 41,100 31,700 23,200 16,400 10,200 5,430 2,260 480
40 62,000 55,200 44,000 33,300 23,800 15,200 8,600 3,520 670
42 65,000 58,000 46,100 35,000 25,000 16,000 9,000 3,700 700
48 91,000 80,900 63,700 43,600 29,100 20,000 11,000 4,600 920
54 125,000 111,000 87,500 60,000 40,000 27,500 15,000 6,000 1,200
60 160,000 140,000 105,000 75,000 50,000 31,000 17,000 7,000 1,400

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Coefficients : 15 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Valve Sizing Coefficients

ASME 300 Series 42/43/4B - Valve Sizing Coefficient (Cv)

Valve Disc Position (Degrees)
Size
Inches 90º 80º 70º 60º 50º 40º 30º 20º 10º
2 1/2 160 136 100 78 50 30 16 8 3
3 185 178 155 123 87 56 32 14 5
4 375 365 315 250 175 115 63 31 10
5 790 675 500 360 238 146 78 41 16
6 1,000 875 710 530 370 240 138 79 26
8 2,000 1,720 1,360 950 630 405 240 121 47
10 2,650 2,250 1,740 1,200 780 510 295 150 61
12 4,000 3,400 2,500 1,690 1,100 710 430 220 92
14 4,100 3,500 2,600 1,770 1,200 830 490 240 100
16 7,800 6,540 4,550 2,970 1,840 1,160 730 420 180
18 9,500 8,000 6,170 4,530 3,110 1,970 1,080 440 94
20 11,000 9,570 7,300 5,400 3,720 2,330 1,250 530 110
24 18,000 15,100 11,400 8,570 5,920 3,700 2,000 830 180
30 29,000 24,400 18,900 13,700 8,500 6,000 3,230 1,330 290
36 45,000 38,100 29,200 21,000 14,800 9,100 4,660 1,730 380
42 60,000 54,000 42,000 30,000 19,000 13,000 7,500 2,600 450
48 83,000 74,000 58,000 41,000 26,000 17,000 10,000 4,400 800
54 Please Consult Factory

ASME 600 Series 44/45 - Valve Sizing Coefficient (Cv)

Valve Disc Position (Degrees)
Size
Inches 90º 80º 70º 60º 50º 40º 30º 20º 10º
3 165 158 135 103 67 46 12 8 3
4 300 270 210 150 95 70 45 30 5
8 1,500 1,350 1,050 750 480 345 209 78 20
10 2,200 1,970 1,540 1,100 700 500 300 140 40
12 3,100 2,790 2,170 1,550 1,000 680 400 190 55
14 3,900 3,300 2,400 1,570 1,100 730 420 200 70
16 5,000 4,200 2,900 1,900 1,200 800 500 250 95
18 6,000 5,000 3,900 2,800 1,900 1,200 660 290 130
20 8,000 6,900 5,300 3,900 2,700 1,700 950 400 143
24 11,000 9,300 7,000 5,200 3,600 2,250 1,200 500 180
30 15,000 13,000 10,000 8,400 5,100 2,800 1,650 600 200

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Coefficients : 16 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Valve Sizing Coefficients

ASME 150 Series 40/41/4A - Valve Sizing Coefficient (Kv)

Valve Disc Position (Degrees)
Size
mm 90º 80º 70º 60º 50º 40º 30º 20º 10º
65 136 116 85 67 43 26 14 7 3
80 158 152 132 105 74 48 27 12 4
100 320 311 269 213 149 98 54 26 9
125 674 576 427 307 203 125 67 35 14
150 1,152 913 640 435 281 186 119 69 30
200 2,388 1,902 1,356 904 584 389 239 141 55
250 3,668 2,943 2,073 1,390 896 597 384 213 85
300 5,672 4,546 3,199 2,158 1,390 921 597 333 132
350 6,525 5,203 3,668 2,474 1,612 1,066 691 384 149
400 8,359 6,705 4,700 3,156 2,064 1,305 870 495 196
450 8,957 7,762 5,937 4,350 3,003 1,894 1,007 427 145
500 11,516 9,980 7,506 5,545 3,839 2,405 1,305 546 171
600 17,060 14,586 10,918 8,163 5,664 3,310 1,877 785 205
650 17,060 14,586 10,918 8,163 5,664 3,310 1,877 785 205
700 23,884 20,387 15,525 11,516 7,933 4,862 2,644 1,109 247
750 27,296 23,287 17,828 13,222 9,127 5,715 3,071 1,288 273
800 29,002 24,822 19,022 14,075 9,724 6,099 3,284 1,373 290
850 29,002 24,822 19,022 14,075 9,724 6,099 3,284 1,373 290
900 41,371 35,058 27,040 19,790 13,989 8,701 4,632 1,928 409
1,000 52,886 47,086 37,532 28,405 20,301 12,966 7,336 3,003 572
1,050 55,445 49,474 39,323 29,855 21,325 13,648 7,677 3,156 597
1,200 77,623 69,008 54,336 37,191 24,822 17,060 9,383 3,924 785
1,350 106,625 94,683 74,638 51,180 34,120 23,458 12,795 5,118 1,024
1,500 136,480 119,420 89,565 63,975 42,650 26,443 14,501 5,971 1,194

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Coefficients : 17 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Valve Sizing Coefficients

ASME 300 Series 42/43/4B - Valve Sizing Coefficient (Kv)

Valve Disc Position (Degrees)
Size
mm 90º 80º 70º 60º 50º 40º 30º 20º 10º
65 136 116 85 67 43 26 14 7 3
80 158 152 132 105 74 48 27 12 4
100 320 311 269 213 149 98 54 26 9
125 674 576 427 307 203 125 67 35 14
150 853 746 606 452 316 205 118 67 22
200 1,706 1,467 1,160 810 537 345 205 103 40
250 2,260 1,919 1,484 1,024 665 435 252 128 52
300 3,412 2,900 2,133 1,442 938 606 367 188 78
350 3,497 2,986 2,218 1,510 1,024 708 418 205 85
400 6,653 5,579 3,881 2,533 1,570 989 623 358 154
450 8,104 6,824 5,263 3,864 2,653 1,680 921 375 80
500 9,383 8,163 6,227 4,606 3,173 1,987 1,066 452 94
600 15,354 12,880 9,724 7,310 5,050 3,156 1,706 708 154
750 24,737 20,813 16,122 11,686 7,251 5,118 2,755 1134 247
900 38,385 32,499 24,908 17,913 12,624 7,762 3,975 1476 324
1,050 51,180 46,062 35,826 25,590 16,207 11,089 6,398 2218 384
1,200 70,799 63,122 49,474 34,973 22,178 14,501 8,530 3753 682
1,350 Please Consult Factory

ASME 600 Series 44/45 - Valve Sizing Coefficient (Kv)

Valve Disc Position (Degrees)
Size
Inches 90º 80º 70º 60º 50º 40º 30º 20º 10º
80 141 135 115 88 57 39 10 7 3
100 256 230 179 128 81 60 38 26 4
200 1,280 1,152 896 640 409 294 178 67 17
250 1,877 1,680 1,314 938 597 427 256 119 34
300 2,644 2,380 1,851 1,322 853 580 341 162 47
350 3,327 2,815 2,047 1,339 938 623 358 171 60
400 4,265 3,583 2,474 1,621 1,024 682 427 213 81
450 5,118 4,265 3,327 2,388 1,621 1,024 563 247 111
500 6,824 5,886 4,521 3,327 2,303 1,450 810 341 122
600 9,383 7,933 5,971 4,436 3,071 1,919 1,024 427 154
750 12,795 11,089 8,530 7,165 4,350 2,388 1,407 512 171

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Coefficients : 18 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Pressure Bar
0 20 40 60 80 100
600 300
500
Carbon Steel Body RTFE Seats

Temperature ºC
Temperature ºF 400 Bray/McCannalok HPBV – Pressure & Temperature
200
300
200 100
100 ASME 150 ASME 300 ASME 600
0
0
-20 -29
0 200 400 600 800 1000 1200 1400 1600
With PTFE Seats: Pressure psig

Pressure Bar
0 20 40 60 80 100
600
300
500
PTFE Seats

Temperature ºC
Stainless Steel Body
Temperature ºF

400 200
300
200 100
100
ASME 150 ASME 300 ASME 600
0
0
-20 -29
0 200 400 600 800 1000 1200 1400 1600
Pressure psig

Pressure Bar
0 20 40 60 80 100
600 300
500
Carbon Steel Body PTFE Seats

Temperature ºC
Temperature ºF

400 200
300
200 100
100 ASME 150 ASME 300 ASME 600
0
0
-20 -29
0 200 400 600 800 1000 1200 1400 1600
Pressure psig

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Press/Temp : 19 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Pressure & Temperature

With RTFE Seats:

Pressure Bar
0 20 40 60 80 100
600
300
500
RTFE Seats

Temperature ºC
Stainless Steel Body
Temperature ºF

400 200
300
200 100
100
ASME 150 ASME 300 ASME 600
0
0
-20 -29
0 200 400 600 800 1000 1200 1400 1600
Pressure psig

Pressure Bar
0 20 40 60 80 100
600 300
500
Carbon Steel Body RTFE Seats

Temperature ºC
Temperature ºF

400 200
300
200 100
100 ASME 150 ASME 300 ASME 600
0
0
-20 -29
0 200 400 600 800 1000 1200 1400 1600
Pressure psig

Pressure Bar
0 20 40 60 80 100
600
300
500
PTFE Seats
Temperature ºC

Stainless Steel Body

Temperature ºF

400 200
300
200 100
100
ASME 150 ASME 300 ASME 600
0
0
-20 -29
All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Press/Temp : 020 The200
technical data herein400 600 only. Product suitability
is for general information 800 should be1000 1200 detailed knowledge
based solely upon customer’s 1400 and experience
1600
with their application.
Pressure psig
 Bray/McCannalok HPBV – Flange Bolting Guide

Flange Bolting Guide

Stud Bolt & 2 Hex Nuts Studs & Hex Nuts

Valve Body Valve Body
Seat Retainer Seat Retainer
Gasket Gasket Gasket Gasket
Flange Flange Flange Flange

Length of Stud Bolt L2 L1

Hex Head Machine Bolt Hex Head Machine Bolts

& Hex Nut
Valve Body Valve Body
Seat Retainer Seat Retainer
Gasket Gasket Gasket Gasket
Flange Flange Flange Flange

Length of Stud Bolt L2 L1

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 21 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Flange Bolting Guide

ASME 150 - Series 40/41

Valve Size STUDS & STUD BOLTS HEX HEAD BOLTS
Ins mm Wafer (Series 40) Qty. Lug (Series 41) Qty. Wafer (Series 40) Qty. Lug (Series 41) Qty.
5/8-11 x 5.50 (L1) 4 5/8-11 x 2.50 (L1) 4 5/8-11 x 5.00 (L1) 4 5/8-11 x 1.50 (L1) 4
2 1/2 65
5/8-11 x 2.75(L2) 4 5/8-11 x 2.00(L2) 4
5/8-11 x 5.50 (L1) 4 5/8-11 x 2.50 (L1) 4 5/8-11 x 5.00 (L1) 4 5/8-11 x 1.50 (L1) 4
3 80
5/8-11 x 2.75(L2) 4 5/8-11 x 2.00(L2) 4
5/8-11 x 5.50 (L1) 8 5/8-11 x 2.50 (L1) 8 5/8-11 x 5.00 (L1) 8 5/8-11 x 1.75 (L1) 8
4 100
5/8-11 x 3.00(L2) 8 5/8-11 x 2.25(L2) 8
3/4-10 x 6.00 (L1) 8 3/4-10 x 2.75 (L1) 8 3/4-10 x 5.25 (L1) 8 3/4-10 x 1.75 (L1) 8
5 125
3/4-10 x 3.25(L2) 8 3/4-10 x 2.25(L2) 8
3/4-10 x 6.00 (L1) 8 3/4-10 x 2.75 (L1) 8 3/4-10 x 5.25 (L1) 8 3/4-10 x 1.75 (L1) 8
6 150
3/4-10 x 3.25(L2) 8 3/4-10 x 2.25(L2) 8
3/4-10 x 6.50 (L1) 8 3/4-10 x 3.00 (L1) 8 3/4-10 x 5.75 (L1) 8 3/4-10 x 2.00 (L1) 8
8 200
3/4-10 x 3.50(L2) 8 3/4-10 x 2.50(L2) 8
7/8-9 x 7.25 (L1) 12 7/8-9 x 3.25 (L1) 12 7/8-9 x 6.50 (L1) 12 7/8-9 x 2.00 (L1) 12
10 250
7/8-9 x 4.00(L2) 12 7/8-9 x 3.00(L2) 12
7/8-9 x 8.00 (L1) 12 7/8-9 x 3.25 (L1) 12 7/8-9 x 7.25 (L1) 12 7/8-9 x 2.00 (L1) 12
12 300
7/8-9 x 4.25(L2) 12 7/8-9 x 3.00(L2) 12
1-8 x 9.00 (L1) 12 1-8 x 4.00 (L1) 12 1-8 x 8.00 (L1) 12 1-8 x 2.50 (L1) 12
14 350
1-8 x 5.00(L2)` 12 1-8 x 3.50(L2) 12
1-8 x 9.50 (L1) 16 1-8 x 4.25 (L1) 16 1-8 x 9.00 (L1) 16 1-8 x 3.00 (L1) 16
16 400
1-8 x 5.00(L2)` 16 1-8 x 3.50(L2) 16
1 1/8-8 x 10.50 (L1) 16 1 1/8-8 x 4.50 (L1) 16 1 1/8-8 x 9.50 (L1) 16 1 1/8-8 x 3.00 (L1) 16
18 450
1 1/8-8 x 5.50(L2) 16 1 1/8-8 x 4.00(L2) 16
1 1/8-8 x 11.50 (L1) 20 1 1/8-8 x 5.00 (L1) 20 1 1/8-8 x 10.00 (L1) 20 1 1/8-8 x 3.50 (L1) 20
20 500
1 1/8-8 x 6.00(L2) 20 1 1/8-8 x 4.50(L2) 20
1 1/4-8 x 13.00 (L1) 20 1 1/4-8 x 5.75 (L1) 20 1 1/4-8 x 11.50 (L1) 20 1 1/4-8 x 4.00 (L1) 20
24 600
1 1/4-8 x 7.00(L2) 20 1 1/4-8 x 5.00(L2) 20
1 1/4-8 x 6.50(L2)* 4 1 1/4-8 x 6.50(L2)* 4 1 1/4-8 x 4.75(L2)* 4 1 1/4-8 x 4.75(L2)* 4
1 1/4-8 x 5.75 (L1)* 4 1 1/4-8 x 5.75 (L1)* 4 1 1/4-8 x 4.00 (L1)* 4 1 1/4-8 x 4.00 (L1)* 4
26 650
1 1/4-8 x 15.25 (L1) 20 1 1/4-8 x 7.25(L2) 20 1 1/4-8 x 13.75 (L1) 20 1 1/4-8 x 5.50(L2) 20
1 1/4-8 x 6.50 (L1) 20 1 1/4-8 x 4.75 (L1) 20
1 1/4-8 x 6.75(L2)* 4 1 1/4-8 x 6.75(L2)* 4 1 1/4-8 x 5.00(L2)* 4 1 1/4-8 x 5.00(L2)* 4
1 1/4-8 x 6.00 (L1)* 4 1 1/4-8 x 6.00 (L1)* 4 1 1/4-8 x 4.25 (L1)* 4 1 1/4-8 x 4.25 (L1)* 4
28 700
1 1/4-8 x 15.50 (L1) 24 1 1/4-8 x 7.25(L2) 24 1 1/4-8 x 14.00 (L1) 24 1 1/4-8 x 5.50(L2) 24
1 1/4-8 x 6.50 (L1) 24 1 1/4-8 x 4.75 (L1) 24
1 1/4-8 x 16.50 (L1) 24 1 1/4-8 x 7.25 (L1) 24 1 1/4-8 x 15.00 (L1) 24 1 1/4-8 x 5.00 (L1) 24
1 1/4-8 x 5.00 (L1)* 4 1 1/4-8 x 8.75(L2) 24 1 1/4-8 x 3.50 (L1)* 4 1 1/4-8 x 6.50(L2) 24
30 750
1 1/4-8 x 6.50(L2)* 4 1 1/4-8 x 5.00 (L1)* 4 1 1/4-8 x 5.00(L2)* 4 1 1/4-8 x 3.50 (L1)* 4
1 1/4-8 x 6.375(L2)* 4 1 1/4-8 x 5.00(L2)* 4
(L1) See illustration on Pg. 21
(L2) See illustration on Pg. 21 - Install from seat retainer side of valve
*Install in flange bolt holes closest to the valve stem
NOTE: Bolt Lengths indicated include allowances for installing 1/16” or 1/8” thick gasket.
Refer to flange standards for bolting material specifications; for example, as listed in ANSI 16.5 and ASME B16.47

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 22 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Flange Bolting Guide

ASME 150 - Series 40/41

Valve Size STUDS & STUD BOLTS HEX HEAD BOLTS
Ins mm Wafer (Series 40) Qty. Lug (Series 41) Qty. Wafer (Series 40) Qty. Lug (Series 41) Qty.
1 1/2-8 x 7.75(L2)* 4 1 1/2-8 x 7.75(L2)* 4 1 1/2-8 x 5.50(L2)* 4 1 1/2-8 x 5.50(L2)* 4
1 1/2-8 x 6.75 (L1)* 4 1 1/2-8 x 6.75 (L1)* 4 1 1/2-8 x 4.75 (L1)* 4 1 1/2-8 x 4.75 (L1)* 4
32 800
1 1/2-8 x 17.75 (L1) 24 1 1/2-8 x 8.50(L2) 24 1 1/2-8 x 16.00 (L1) 24 1 1/2-8 x 6.50(L2) 24
1 1/2-8 x 7.50 (L1) 24 1 1/2-8 x 5.25 (L1) 24
1 1/2-8 x 7.75(L2)* 4 N/A 1 1/2-8 x 5.75(L2)* 4 N/A
34 850 1 1/2-8 x 6.75 (L1)* 4 1 1/2-8 x 4.75 (L1)* 4
1 1/2-8 x 18.25 (L1) 28 1 1/2-8 x 16.50 (L1) 28
1 1/2-8 x 19.00 (L1) 28 1 1/2-8 x 7.00 (L1) 28 1 1/2-8 x 17.50 (L1) 28 1 1/2-8 x 6.00 (L1) 28
1 1/2-8 x 5.75 (L1)* 4 1 1/2-8 x 8.25(L2) 28 1 1/2-8 x 4.00 (L1)* 4 1 1/2-8 x 7.00(L2) 28
36 900
1 1/2-8 x 6.75(L2)* 4 1 1/2-8 x 5.75 (L1)* 4 1 1/2-8 x 5.00(L2)* 4 1 1/2-8 x 4.00 (L1)* 4
1 1/2-8 x 6.75(L2)* 4 1 1/2-8 x 5.00(L2)* 4
N/A N/A 1 1/2-8 x 8.00 (L1)* 4 N/A N/A 1 1/2-8 x 5.75(L2)* 4
1 1/2-8 x 7.25(L2)* 4 1 1/2-8 x 5.25 (L1)* 4
40 1,000
1 1/2-8 x 8.75 (L1) 32 1 1/2-8 x 6.75(L2) 32
1 1/2-8 x 8.00(L2) 32 1 1/2-8 x 6.00 (L1) 32
1 1/2-8 x 21.00 (L1) 32 1 1/2-8 x 8.00 (L1) 32 1 1/2-8 x 19.50 (L1) 32 1 1/2-8 x 6.00 (L1) 32
1 1/2-8 x 7.50 (L1)* 4 1 1/2-8 x 9.00(L2) 32 1 1/2-8 x 5.50 (L1)* 4 1 1/2-8 x 7.00(L2) 32
42 1,050
1 1/2-8 x 8.25(L2)* 4 1 1/2-8 x 7.50 (L1)* 4 1 1/2-8 x 6.00(L2)* 4 1 1/2-8 x 5.50 (L1)* 4
1 1/2-8 x 8.25(L2)* 4 1 1/2-8 x 6.00(L2)* 4
1 1/2-8 x 8.75(L2)* 4 1 1/2-8 x 8.75(L2)* 4 1 1/2-8 x 6.50(L2)* 4 1 1/2-8 x 6.50(L2)* 4
1 1/2-8 x 8.00 (L1)* 4 1 1/2-8 x 8.00 (L1)* 4 1 1/2-8 x 6.00 (L1)* 4 1 1/2-8 x 6.00 (L1)* 4
48 1,200
1 1/2-8 x 22.50 (L1) 40 1 1/2-8 x 9.25(L2) 40 1 1/2-8 x 20.50 (L1) 40 1 1/2-8 x 7.25(L2) 40
1 1/2-8 x 9.00 (L1) 40 1 1/2-8 x 6.75 (L1) 40
1 3/4-8 x 10.00(L2)* 4 1 3/4-8 x 10.00(L2)* 4 1 3/4-8 x 7.75(L2)* 4 1 3/4-8 x 7.75(L2)* 4
1 3/4-8 x 8.75 (L1)* 4 1 3/4-8 x 8.75 (L1)* 4 1 3/4-8 x 6.50 (L1)* 4 1 3/4-8 x 6.50 (L1)* 4
54 1,350
1 3/4-8 x 24.75 (L1) 40 1 3/4-8 x 11.25(L2) 40 1 3/4-8 x 20.50 (L1) 40 1 3/4-8 x 9.00(L2) 40
1 3/4-8 x 10.00 (L1) 40 1 3/4-8 x 7.75(L1) 40
N/A N/A 1 3/4-8 x 10.25(L2)* 4 N/A N/A 1 3/4-8 x 8.00(L2)* 4
1 3/4-8 x 9.00 (L1)* 4 1 3/4-8 x 6.75 (L1)* 4
60 1,500
1 3/4-8 x 12.00(L2) 48 1 3/4-8 x 9.75(L2) 48
1 3/4-8 x 11.00 (L1) 48 1 3/4-8 x 8.75 (L1) 48
(L1) See illustration on Pg. 21
(L2) See illustration on Pg. 21 - Install from seat retainer side of valve
*Install in flange bolt holes closest to the valve stem
NOTE: Bolt Lengths indicated include allowances for installing 1/16” or 1/8” thick gasket.
Refer to flange standards for bolting material specifications; for example, as listed in ANSI 16.5 and ASME B16.47

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 23 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Flange Bolting Guide

ASME 300 - Series 42/43

Valve Size STUDS & STUD BOLTS HEX HEAD BOLTS
Ins mm Wafer (Series 42) Qty. Lug (Series 43) Qty. Wafer (Series 42) Qty. Lug (Series 43) Qty.
3/4-10 x 6.00 (L1) 8 3/4-10 x 2.75 (L1) 8 3/4-10 x 5.50 (L1) 8 3/4-10 x 1.75 (L1) 8
2 1/2 65
3/4-10 x 3.25(L2) 8 3/4-10 x 2.25(L2) 8
3/4-10 x 6.00 (L1) 8 3/4-10 x 2.75 (L1) 8 3/4-10 x 5.50 (L1) 8 3/4-10 x 1.75 (L1) 8
3 80
3/4-10 x 3.25(L2) 8 3/4-10 x 2.25(L2) 8
3/4-10 x 6.25 (L1) 8 3/4-10 x 3.00 (L1) 8 3/4-10 x 5.25 (L1) 8 3/4-10 x 2.00 (L1) 8
4 100
3/4-10 x 3.50(L2) 8 3/4-10 x 2.50(L2) 8
3/4-10 x 7.25 (L1) 8 3/4-10 x 3.50 (L1) 8 3/4-10 x 6.25 (L1) 8 3/4-10 x 2.50 (L1) 8
5 125
3/4-10 x 4.00(L2) 8 3/4-10 x 3.25(L2) 8
3/4-10 x 7.75 (L1) 12 3/4-10 x 3.75 (L1) 12 3/4-10 x 6.50 (L1) 12 3/4-10 x 2.50 (L1) 12
6 150
3/4-10 x 4.00(L2) 12 3/4-10 x 3.00(L2) 12
7/8-9 x 8.25 (L1) 12 7/8-9 x 4.00 (L1) 12 7/8-9 x 7.50 (L1) 12 7/8-9 x 3.00 (L1) 12
8 200
7/8-9 x 4.50(L2) 12 7/8-9 x 3.50(L2) 12
1-8 x 9.50 (L1) 16 1-8 x 4.50 (L1) 16 1-8 x 8.50 (L1) 16 1-8 x 3.50 (L1) 16
10 250
1-8 x 5.00(L2) 16 1-8 x 3.50(L2) 16
1 1/8-8 x 10.25 (L1) 16 1 1/8-8 x 4.75 (L1) 16 1 1/8-8 x 9.25 (L1) 16 1 1/8-8 x 3.50 (L1) 16
12 300
1 1/8-8 5.50(L2) 16 1 1/8-8 4.00(L2) 16
1 1/8-8 x 11.75 (L1) 16 1 1/8-8 x 5.50 (L1) 20 1 1/8-8 x 10.50 (L1) 16 1 1/8-8 x 4.00 (L1) 16
1 1/8-8 x 5.50 (L1)* 4 1 1/8-8 x 6.00 (L2) 20 1 1/8-8 x 3.00 (L1)* 4 1 1/8-8 x 4.00(L2) 16
14 350
1 1/8-8 x 6.00 (L2)* 4 1 1/8-8 x 3.50(L2)* 4 1 1/8-8 x 3.00 (L1)* 4
1 1/8-8 x 3.50(L2)* 4
1 1/4-8 x 13.00 (L1) 16 1 1/4-8 x 6.00 (L1) 20 1 1/4-8 x 11.75 (L1) 16 1 1/4-8 x 4.00 (L1) 16
1 1/4-8 x 5.00 (L1)* 4 1 1/4-8 x 6.50(L2) 20 1 1/4-8 x 3.50 (L1)* 4 1 1/4-8 x 4.50(L2) 16
16 400
1 1/4-8 x 5.50(L2)* 4 1 1/4-8 x 4.00(L2)* 4 1 1/4-8 x 3.50 (L1)* 4
1 1/4-8 x 5.00(L2)* 4
1 1/4-8 x 14.00 (L1) 20 1 1/4-8 x 6.25 (L1) 24 1 1/4-8 x 13.00 (L1) 20 1 1/4-8 x 4.50 (L1) 20
1 1/4-8 x 5.50 (L1)* 8 1 1/4-8 x 7.25(L2) 24 1 1/4-8 x 3.50 (L1)* 4 1 1/4-8 x 5.00(L2) 20
18 450
1 1/4-8 x 4.00(L2)* 4 1 1/4-8 x 3.50 (L1)* 4
1 1/4-8 x 4.50(L2)* 4
1 1/4-8 x 14.50 (L1) 20 1 1/4-8 x 6.75 (L1) 24 1 1/4-8 x 13.00 (L1) 20 1 1/4-8 x 4.50(L1) 20
1 1/4-8 x 5.50 (L1)* 4 1 1/4-8 x 7.50(L2) 24 1 1/4-8 x 4.00 (L1)* 4 1 1/4-8 x 5.00(L2) 20
20 500
1 1/4-8 x 6.00(L2)* 4 1 1/4-8 x 4.50(L2)* 4 1 1/4-8 x 4.00(L1)* 4
1 1/4-8 x 5.00(L2)* 4
1 1/2-8 x 16.25 (L1) 20 1 1/2-8 x 6.50 (L1) 24 1 1/2-8 x 15.00 (L1) 20 1 1/2-8 x 5.00(L1) 20
1 1/2-8 x 6.25 (L1)* 4 1 1/2-8 x 7.50(L2) 24 1 1/2-8 x 4.50 (L1)* 4 1 1/2-8 x 6.00(L2) 20
24 600
1 1/2-8 x 6.75(L2)* 4 1 1/2-8 x 5.50(L2)* 4 1 1/2-8 x 4.50(L1)* 4
1 1/2-8 x 5.50(L2)* 4
1 3/4-8 x 20.50 (L1) 24 1 3/4-8 x 8.00 (L1) 28 1 3/4-8 x 19.00 (L1) 24 1 3/4-8 x 6.50(L1) 28
30 750 1 3/4-8 x 8.25 (L1)* 8 1 3/4-8 x 9.25(L2) 28 1 3/4-8 x 6.00 (L1)* 4 1 3/4-8 x 7.00(L2) 24
1 3/4-8 x 6.50(L2)* 4 1 3/4-8 x 7.00(L2)* 4
(L1) See illustration on Pg. 21
(L2) See illustration on Pg. 21 - Install from seat retainer side of valve
*Install in flange bolt holes closest to the valve stem
NOTE: Bolt Lengths indicated include allowances for installing 1/16” or 1/8” thick gasket.
Refer to flange standards for bolting material specifications; for example, as listed in ANSI 16.5 and ASME B16.47

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 24 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Flange Bolting Guide

ASME 300 - Series 42/43

Valve Size STUDS & STUD BOLTS HEX HEAD BOLTS
Ins mm Wafer (Series 42) Qty. Lug (Series 43) Qty. Wafer (Series 42) Qty. Lug (Series 43) Qty.
2-8 x 24.00 (L1) 28 2-8 x 10.00 (L1) 56 2-8 x 22.00 (L1) 28 2-8 x 7.00(L1) 28
36 900 2-8 x 8.75 (L1)* 8 2-8 x 9.00 (L1) 8 2-8 x 6.50(L2) 8 2-8 x 6.50(L1)* 8
2-8 x 7.50(L2) 28
N/A 1 5/8-8 x 9.50(L2)* 4 N/A 1 5/8-8 x 7.50(L2)* 4
1 5/8-8 x 8.50 (L1)* 4 1 5/8-8 x 6.50(L1)* 4
40 1,000
1 5/8-8 x 10.25(L2) 28 1 5/8-8 x 8.00(L2) 28
1 5/8-8 x 9.25 (L1) 28 1 5/8-8 x 7.00(L1) 28
N/A 1 5/8-8 x 9.50(L2)* 4 N/A 1 5/8-8 x 7.50(L2)* 4
1 5/8-8 x 8.50 (L1)* 4 1 5/8-8 x 6.50(L1)* 4
42 1,050
1 5/8-8 x 10.50(L2) 28 1 5/8-8 x 8.50(L2) 28
1 5/8-8 x 9.50 (L1) 28 1 5/8-8 x 7.25(L1) 28
N/A 1 3/4-8 x 10.50(L2)* 4 N/A 1 3/4-8 x 8.25(L2)* 4
1 3/4-8 x 9.00(L1)* 4 1 3/4-8 x 6.75(L1)* 4
44 1,100
1 3/4-8 x 11.25(L2) 28 1 3/4-8 x 9.00(L2) 28
1 3/4-8 x 9.75(L1) 28 1 3/4-8 x 7.50(L1) 28
N/A 1 7/8-8 x 10.75(L2)* 4 N/A 1 7/8-8 x 8.25(L2)* 4
1 7/8-8 x 9.50(L1)* 4 1 7/8-8 x 7.75(L1)* 4
48 1,200
1 7/8-8 x 12.00(L2) 28 1 7/8-8 x 9.50(L2) 28
1 7/8-8 x 11.00(L1) 28 1 7/8-8 x 8.50(L1) 28
N/A N/A 1 1/2-8 x 8.00 (L1)* 4 N/A
1 1/2-8 x 7.25(L2)* 4
40 1,000
1 1/2-8 x 8.75 (L1) 32
1 1/2-8 x 8.00(L2) 32
1 1/2-8 x 21.00 (L1) 32 1 1/2-8 x 8.00 (L1) 32 1 1/2-8 x 19.50 (L1) 32 1 1/2-8 x 6.00 (L1) 32
1 1/2-8 x 7.50 (L1)* 4 1 1/2-8 x 9.00(L2) 32 1 1/2-8 x 5.50 (L1)* 4 1 1/2-8 x 7.00(L2) 32
42 1,050
1 1/2-8 x 8.25(L2)* 4 1 1/2-8 x 7.50 (L1)* 4 1 1/2-8 x 6.00(L2)* 4 1 1/2-8 x 5.50 (L1)* 4
1 1/2-8 x 8.25(L2)* 4 1 1/2-8 x 6.00(L2)* 4
1 1/2-8 x 8.75(L2)* 4 1 1/2-8 x 8.75(L2)* 4 1 1/2-8 x 6.50(L2)* 4 1 1/2-8 x 6.50(L2)* 4
1 1/2-8 x 8.00 (L1)* 4 1 1/2-8 x 8.00 (L1)* 4 1 1/2-8 x 6.00 (L1)* 4 1 1/2-8 x 6.00 (L1)* 4
48 1,200
1 1/2-8 x 22.50 (L1) 40 1 1/2-8 x 9.25(L2) 40 1 1/2-8 x 20.50 (L1) 40 1 1/2-8 x 7.25(L2) 40
1 1/2-8 x 9.00 (L1) 40 1 1/2-8 x 6.75 (L1) 40
1 3/4-8 x 10.00(L2)* 4 1 3/4-8 x 10.00(L2)* 4 1 3/4-8 x 7.75(L2)* 4 1 3/4-8 x 7.75(L2)* 4
1 3/4-8 x 8.75 (L1)* 4 1 3/4-8 x 8.75 (L1)* 4 1 3/4-8 x 6.50 (L1)* 4 1 3/4-8 x 6.50 (L1)* 4
54 1,350
1 3/4-8 x 24.75 (L1) 40 1 3/4-8 x 11.25(L2) 40 1 3/4-8 x 20.50 (L1) 40 1 3/4-8 x 9.00(L2) 40
1 3/4-8 x 10.00 (L1) 40 1 3/4-8 x 7.75(L1) 40
N/A N/A 1 3/4-8 x 10.25(L2)* 4 N/A N/A 1 3/4-8 x 8.00(L2)* 4
1 3/4-8 x 9.00 (L1)* 4 1 3/4-8 x 6.75 (L1)* 4
60 1,500
1 3/4-8 x 12.00(L2) 48 1 3/4-8 x 9.75(L2) 48
1 3/4-8 x 11.00 (L1) 48 1 3/4-8 x 8.75 (L1) 48
(L1) See illustration on Pg. 21
(L2) See illustration on Pg. 21 - Install from seat retainer side of valve
*Install in flange bolt holes closest to the valve stem
NOTE: Bolt Lengths indicated include allowances for installing 1/16” or 1/8” thick gasket.
Refer to flange standards for bolting material specifications; for example, as listed in ANSI 16.5 and ASME B16.47

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 25 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.
 Bray/McCannalok HPBV – Flange Bolting Guide

ASME 600 - Series 44/45

Valve Size STUDS & STUD BOLTS HEX HEAD BOLTS
Ins mm Wafer (Series 44) Qty. Lug (Series 45) Qty. Wafer (Series 44) Qty. Lug (Series 45) Qty.
3/4-10 x 7.25(L1) 8 3/4-10 x 3.75(L2) 8 3/4-10 x 6.25(L1) 8 3/4-10 x 2.50(L2) 8
3 80
3/4-10 x 3.50(L1) 8 3/4-10 x 2.25(L1) 8
7/8-9 x 8.75(L1) 8 7/8-9 x 4.50(L2) 8 7/8-9 x 7.50(L1) 8 7/8-9 x 3.25(L2) 8
4 100
7/8-9 x 4.00(L1) 8 7/8-9 x 2.50(L1) 8
1.00-8 x 10.25(L1) 12 1.00-8 x 5.50(L2) 12 1.00-8 x 9.25(L1) 12 1.00-8 x 4.00(L2) 12
6 150
1.00-8 x 5.00(L1) 12 1.00-8 x 3.25(L1) 12
1 1/8-8 x 12.00(L1) 12 1 1/8-8 x 6.50(L2) 12 1 1/8-8 x 10.75(L1) 12 1 1/8-8 x 4.75(L2) 12
8 200
1 1/8-8 x 5.75(L1) 12 1 1/8-8 x 4.00(L1) 12
1 1/4-8 x 6.25(L2)* 4 1 1/4-8 x 6.75(L2)* 4 1 1/4-8 x 4.75(L2)* 4 1 1/4-8 x 5.00(L2)* 4
1 1/4-8 x 5.75(L1)* 4 1 1/4-8 x 5.75(L1)* 4 1 1/4-8 x 4.00(L1)* 4 1 1/4-8 x 4.00(L1)* 4
10 250 1 1/4-8 x 13.50(L1) 12 1 1/4-8 x 7.25(L2) 12
1 1/4-8 x 12.25(L1) 12 1 1/4-8 x 5.50(L2) 12
1 1/4-8 x 6.25(L1) 12
1 1/4-8 x 4.50(L1) 12
1 1/4-8 x 6.50(L2)* 4 1 1/4-8 x 7.00(L2)* 4 1 1/4-8 x 5.25(L2)* 4 1 1/4-8 x 5.00(L2)* 4
1 1/4-8 x 6.00(L1)* 4 1 1/4-8 x 6.00(L1)* 4 1 1/4-8 X 4.25(L1)* 4 1 1/4-8 x 4.00(L1)* 4
12 300 1 1/4-8 X 14.50(L1) 16 1 1/4-8 x 7.50(L2) 16
1 1/4-8 X 13.50(L1) 16 1 1/4-8 x 5.75(L2) 16
1 1/4-8 x 6.50(L1) 16
1 1/4-8 x 4.75(L1) 16
1 3/8-8 x 6.50(L2)* 4 1 3/8-8 x 6.50(L2)* 4 1 3/8-8 x 4.50(L2)* 4 1 3/8-8 x 4.50(L2)* 4
1 3/8-8 x 6.25(L1)* 4 1 3/8-8 x 6.25(L1)* 4 1 3/8-8 x 4.25(L1)* 4 1 3/8-8 x 4.25(L1)* 4
14 350 1 3/8-8 x 15.25(L1) 16 1 3/8-8 x 7.25(L2) 16
1 3/8-8 x 10.75(L1) 16 1 3/8-8 x 5.25(L2) 16
1 3/8-8 x 6.75(L1) 16
1 3/8-8 x 5.00(L1) 16
1 1/2-8 x 7.00(L2)* 4 1 1/2-8 x 7.00(L2)* 4 1 1/2-8 x 4.75(L2)* 4 1 1/2-8 x 4.75(L2)* 4
1 1/2-8 x 6.75(L1)* 4 1 1/2-8 x 6.75(L1)* 4 1 1/2-8 x 4.50(L1)* 4 1 1/2-8 x 4.50(L1)* 4
16 400 1 1/2-8 x 17.00(L1) 16 1 1/2-8 x 7.75(L2) 16
1 1/2-8 x 11.50(L1) 16 1 1/2-8 x 5.50(L2) 16
1 1/2-8 x 7.50(L1) 16
1 1/2-8 x 5.25(L1) 16
1 5/8-8 x 8.00(L2)* 4 1 5/8-8 x 8.00(L2)* 4 1 5/8-8 x 5.50(L2)* 4 1 5/8-8 x 5.50(L2)* 4
1 5/8-8 x 7.50(L1)* 4 1 5/8-8 x 7.50(L1)* 4 1 5/8-8 x 5.00(L1)* 4 1 5/8-8 x 5.00(L1)* 4
18 450 1 5/8-8 x 19.00(L1) 16 1 5/8-8 x 8.75(L2) 16
1 5/8-8 x 13.00(L1) 16 1 5/8-8 x 6.25(L2) 16
1 5/8-8 x 8.25(L1) 16
1 5/8-8 x 5.75(L1) 16
1 7/8-8 x 8.50(L2)* 4 1 7/8-8 x 8.50(L2)* 4 1 7/8-8 x 6.00(L2)* 4 1 7/8-8 x 6.00(L2)* 4
1 7/8-8 x 7.75(L1)* 4 1 7/8-8 x 7.75(L1)* 4 1 7/8-8 x 5.25(L1)* 4 1 7/8-8 x 5.25(L1)* 4
20 500 1 7/8-8 x 20.25(L1) 20 1 7/8-8 x 9.25(L2) 20
1 7/8-8 x 14.00(L1) 20 1 7/8-8 x 6.75(L2) 20
1 7/8-8 x 8.50(L1) 20
1 7/8-8 x 6.00(L1) 20
1 7/8-8 x 9.00(L2)* 4 1 7/8-8 x 9.00(L2)* 4 1 7/8-8 x 6.25(L2)* 4 1 7/8-8 x 6.25(L2)* 4
1 7/8-8 x 8.00(L1)* 4 1 7/8-8 x 8.00(L1)* 4 1 7/8-8 x 5.25(L1)* 4 1 7/8-8 x 5.25(L1)* 4
24 600 1 7/8-8 x 22.50(L1) 20 1 7/8-8 x 9.75(L2) 20
1 7/8-8 x 15.25(L1) 20 1 7/8-8 x 7.00(L2) 20
1 7/8-8 x 9.50(L1) 20
1 7/8-8 x 6.75(L1) 20
30 750
(L1) See illustration on Pg. 21
(L2) See illustration on Pg. 21 - Install from seat retainer side of valve
*Install in flange bolt holes closest to the valve stem
NOTE: Bolt Lengths indicated include allowances for installing 1/16” or 1/8” thick gasket.
Refer to flange standards for bolting material specifications; for example, as listed in ANSI 16.5 and ASME B16.47

All information herein is proprietary and confidential and may not be copied or reproduced without the expressed written consent of BRAY INTERNATIONAL, Inc.
Flange Bolting : 26 The technical data herein is for general information only. Product suitability should be based solely upon customer’s detailed knowledge and experience with their application.