Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Ingginw PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 12

International Journal of

Development Strategies in Humanities, Management and Social Sciences | IJDSHMSS


ISSN Hard Print: 2360-9036 | ISSN Online: 2360-9044 | Volume 7, Number 1 May, 2017

Extraction and Utilization of Natural Dye Extract from


Guinea Corn Leaf

1 2
Nwonye, N. U. & Priscilla Nnenna Ezema
1
Department of Home Economics, Nutrition & Dietetics, University of Uyo
2
Department of Home Economics, Hospitality Management and Tourism,
Michael Okpara University of Agriculture, Umudike

Abstract

T he leaves of guinea corn were bought from the market, chopped and the dye
content was extracted using water and acetone respectively as solvents. The
extraction of the dye was done using cold method (maceration) and soxhlet.
This work was on guinea corn, a potential source of dye stuff for textile and food. The
objective of the study was to assess the dye and colouring potential of the extracts from
guinea corn, using different techniques of dye extraction: assess the light, washing and
rubbing fastness properties and to impart colour on food using the extracted dye. To
achieve the above objectives, guinea corn leaf, alum, cotton fabric and other materials
were bought from the market in Aba. The experiment was carried out in chemistry
laboratory in the University of Uyo, Uyo Akwa Ibom State. The sample was treated and
the substrate was scoured and mordanted. Cold maceration and soxhlet extraction were
employed using distilled water and acetone as solvents. The dye was produced in four
states using distilled water and acetone plus sample in maceration and the yield were
wine and slightly deep wine respectively while in soxhlet extraction, distilled water plus
sample and acetone plus sample yielded slightly reddish brown and reddish brown
colours. The extracted dyes were applied on cotton fabric treated with alum. The colours
after dyeing yielded blush, deep blush, brick and deep brick respectively. The extracted
dye was also used to impart colour on foods. It was therefore concluded that the process
of the extraction was eco-friendly. The dye obtained has the dyeing potential which can
be used as a source of textile dyeing and food colouring. It is therefore recommended
that efforts should be made towards producing natural dyes as they are eco-friendly and
can be produced in different shades.

Keywords: Extraction, Natural dye, Acetone, Soxhlet, Maceration, Guinea corn leaf

Corresponding Author: Nwonye, N. U.

http://internationalpolicybrief.org/journals/international-scientific-research-consortium-journals/intl-jrnl-of-development-strategies-in-humanities-vol7-no1-may2017

IJDSHMSS | Page 40
Background to the Study
Natural dyes can be obtained from various parts of plants such as flowers, roots, leaves, barks,
insects' secretion and minerals. These plants can be found in our environment. Although dyes
abound in the natural environment, they can also be formed in different ways and used in
different applications depending on their manufacturing processes (Obenewaa, 2010).
Osobohien (2009) defined natural dyes as substances from plants and animals that impart
colour to foods, cosmetics, drugs, hair, fibre, fur and polymers. The dyes are introduced to
different items to upgrade their appearance and make them attractive for consumers to
patronize. Irrespective of the pressing issue connected with use of natural dyes such as poor
yield, poor adherence to textile materials, there is the need for sustainable processes which can
be seen as the driving force for the development of new strategies to revive the use of natural
dyes.

Natural dyes can exhibit better biodegradability and generally possess higher compatibility
with the environment compared to synthetic dyes (Osabohien, 2009) and Otutu et al, 2010).
Round the universe efforts are tailored toward promoting the cultivation of natural dye plants
and their application in dyeing (Osabbohien, 2014). This has been possible because they are
eco-friendly compared to synthetic dyes.

Synthetic dyes are synthesized from petro chemical sources through hazardous chemical
processes which pose a threat to the environment (Ekong, 2016) Researches have shown that
synthetic dyes are suspected to release harmful chemicals that are allergic, carcinogenic and
detrimental to human health (Mansour, 2013). Textiles industries produce large amounts of
polluted effluents that are normally discharged to surfaces of water bodies and ground water
aquifers. This chemical waste contribute several damages to the ecological system of the
receiving water surfaces, creating a lot of problem to ground water resources. In 1996,
Germany became the first country to ban certain azo dyes. As the world demand for fibres and
safety dyes increases, consumers became conscious of environmental hazards posed by
synthetic dyes which causes skin cancer, disorders and allergic contact dermatitis. This
condition of environmental consciousness had lead to the rebirth of interest in natural dye
(Kultam and Gokhale, 2011). There has become the necessity to develop natural dyes as they
have better bio-degradability with the environment. They are non-toxic, non-allergic to the
skin, non-carcinogenetic, easily available and renewable (Thiyaparajan, Balakrishn and
Tarnilaras, 2015). For proper technical extraction and application of natural dyes, efficient
method of extraction and adequate use of solvents that will be able to extract the dye from the
plant has to be employed. This has led to so many research works carried out across the world
on the application of natural dyes as important alternatives to synthetic dyes (Acguah and
Oduro, 2012).

The African continent is rich in different plant species with potential to produce novel natural
products with dye-yielding properties (Wanyama et al, 2014). The authors reported that India
alone has abundance of dye-yielding plants from whose different parts extraction of colour
components for textile application and commercialization are gaining prominence in that part
of the world. Nigeria has abundant resources in terms of plants which contain dyes in parts
such as the roots, bark, leaves, seeds, fruits and flowers. One of such plant is guinea corn.

Guinea corn (sorghum bicolor) belongs to the grass family, Poaceae. The genus sorghum is one
of about 100 genera of Poaceae. The genus is in the sub family, panicodeae and the tribe,

IJDSHMSS | Page 41
andropogoneae. It is called kopo-mopo-re-corn in Yoruba, millomaize in United states (U.S),
dura in Sudanm great millet and guinea corn in West Africa, kafir corn in South Africa,
Mtama in Eastern Africa, and jowar in India (FAO, 1995 in Osabohieri, 2014). Sorghum is
known by inflorescence (lead) and grain (Fruiter edible seed) in the fern of a panicle, spikelets
borne in pairs and extensively branching roots. It is particularly more grown in warmer
climates of the world. As grain, sorghum is used as food for people, livestock and poultry. It is
the fifth most important cereal crop in the world, sorghum grass family have hollow stems
(Culms) that are plugged at intervals (the nodes), with leaves arising at the nodes. The leaves
generally are differentiated with a lower sheath hugging the stems from a distance and a blade.
Sorghum bicolor originated in Northern Africa and can grow in arid soil and withstand
prolonged droughts. It grows in clumps that may reach over four meters high. The grain (seed)
is small, reaching about 3 - 4 mm in diameter. The colour of the special seeds varies from white
through red and brown, pale yellow to deep purple brown etc.

The United states is the world producer of sorghum followed by India and Nigeria (FSD,
2007). In U.S, Australia and Argentina, Its growth habit is similar to that of maize, but with
more side shoots and a more extensively branched root system. It is generally used as food,
fodder, in the production of biodiesel, construction of brooms and brushes etc.

Guinea corn leaf is an important source of carbohydrate, protein and minerals such as
calcium, selemum, manganese and iron in which the bioavailability depends on the level of
interactions with various anti-nutrients (FAO, 2001). It is also rich in B-complex vitamins.
Apart from its uses as food, it contains some chemical compounds that are protective against
cancer, heart disease, heavy menstrual flow and tumor growth (Oyetaya and Ogunrotimi,
2012). Guinea corn leaves form an addition to the huge mass of environmental pollutants from
crop harvest. Oyetaya and Ogunrotimi, (2012) discovered that guinea corn leaf is a potential
source of nutrients and an essential antioxidant compound which could supplement human
and animal diets instead of constituting a waste and source of environmental pollution.
Therefore it is a good source for dye extraction.

In extracting dye from plants, different techniques can be used. Examples of such techniques
are maceration and soxhlet extraction. Maceration is a technique used in extracting dye from
plants that involves leaving the pulverized plant to soak in a suitable solvent in a closed
container. Cold maceration is done at room temperature by mixing the plant with the solvent
and leaving the mixture for several hours while occasionally shaking or stirring. Finally the
extract in strained from the plant particles (Malidi and Altikriti, 2010, Neha and Vidya, 2011).
Temperature in maceration can be cold or hot. This type of technique requires no special
apparatus like the soxhlet.

Soxhlet extraction is a technique that places a specialized piece of glass ware in between a flask
and a condenser. The refluxing soxhlet repeatedly washes the solid extracting the desired
compounds into the flask. The technique is mostly carried out for colourant identification. The
temperature of the instrument is always maintained well under the boiling point of the solvent
used. Several cycles of the solvent is run as to extract all the compounds from the plant part for
dye application.

Dye application is the widely used procedure in adding colour to fibres, yarns and fabrics.
When a fabric is exposed or introduced into the dye bath the item absorbs the molecules of the

IJDSHMSS | Page 42
dye. Any excess dye that remains on the outside of the fabric can bleed or become sensitive to
surface abrasion, chemical additives or mordants such as salt and alum which most times are
used to facilitate absorption of dye into cotton fibre. Colouring matters extracted from plants
has diversified exceptions and have little or no colouring power by themselves except when
used in conjunction with a mordant. Osabohien (2009) confirmed that many of the natural
dyes have poor affinity for textile materials unless they are treated with a mordant.

Mordants are chemical agents which allow a reaction to occur between the dye and the fabric
thereby aiding in fixing the colour to the fabric. Mordants fix the dye to a substrate by
combining with the dye pigment to form an insoluble compound (wipperlinger, 2004).
Obenewaa (2010) commented that mordant is an essential part of the dyeing process. It is very
essential except for plants which contain a lot of tannin and do not necessarily require
mordants. Not all dyes accept mordants. Natural dyes can be substantive and adjective.
Substantive dyes like lichens and walnut need no mordant to help them adhere to the fabric.
Adjective dyes do. The mordant joins with the fabric and the dye to set the colour permanently.
It enters deep into the fiber, and when the dye is added they combine to form a good colour
(Earth Guild, 2016).

Mordants that are regularly used are ALUM (potassium aluminum sulfate), IRON (fereous
sulfate) TIN (stannous chloride) BLUE VERTICAL (Copper sulfate) TANNIC ACID,
GLAUBER'S SALT, and CREAM OF TARTAR. Alum is the most common mordant. It does
not affect colour. It can be used with cream of tartar which helps evenness and brightens
slightly. Iron is also called copperas. It sadden or darken colours, bringing out green shades.
Cotton and wool are dyed before mordanting with iron when darker shades are required and
Tin blooms or brightens colour. Regular used with cream of tartar. Tin is poisonous. It is a good
additive. Blue vitriol sadden the colour and brings out green. It is a good additive. It is also
poisonous. Tannic acid is a good mordant for vegetable fibers. Cream of tartar is used in some
cases as additives to help in getting evenness and brightens slightly. Apart from textile dyeing,
natural dye extract can be used to impart colour on foods.

Food has always been assessed firstly by its colour when it comes to desirability. The act of
eating is a multi-sensory experience, synthesizing perceptions of sight, taste, smell and touch,
colour provides visual information about a food quality and condition, and influences the
perception of its flavor. In nature, colour is determined by a food's inherent qualities, indicating
types of flavor and degrees of sweetness, ripeness or decay (Obenewaa, 2010). Humans have
continued to add or change the natural colour in food from very early times and for a variety of
reasons such as aesthetic purposes to increase appetite and appeal, for symbolic effects, to
make a less desirable food seem more desirable, and to mask defects. From ancient times, other
varieties of food colourants have been derived from plant, animal, and mineral sources.

This study was based on using the guinea corn leaves for dye extraction that is environmentally
friendly. The extraction was aimed at using different solvents and different methods of
extraction to ascertain the most effective means of extracting the dye pigments from the plant.
Furthermore, the study was also focused on mordanting the substrate with alum before dyeing.
The study also used the extracted dye to impart colour on foods.

IJDSHMSS | Page 43
Materials and Methods
Materials
The dried leaves of the Guinea corn used for the work was purchased from New Market in Aba
South, Abia State. The cotton fabric, baking soda, Aceton, and alum were obtained from old
market in Aba South of Abia State. All chemicals used as solvent for extraction were of
analytical grade and required no purification.

Equipment/instrument
Apparatus used for the experiments include: Volumetric flask (100ml/ 500ml),Beakers of
varying sizes, Graduated measuring cylinder of volume size 10,20,25 and 100ml, Soxhlet
apparatus, Heating mantle, Weighing balance, Pot, Bath, Rotary evaporator. The equipments
were obtained from the chemical laboratory of the department of chemistry, University of
Uyo, Uyo Akwa Ibom state, Nigeria. Water was provided in the chemistry laboratory.

Treatment of Sample
The plant sample was washed with distilled water to remove dirt and later checked for final
spots on the leaves which may produce adverse effects on the extraction process of the dye stuff.
The guinea corn leaves sample was reduced to smaller pieces using knife. See below.

Samples of guinea corn leaves

Treatment of Substrate
Scouring the substrate: The substrate (White Cotton) was simmered in a solution of dish soap.
This removed the oil, wax or dirt that might interfere with dye adhering to the fiber. After, the
substrate was rinsed properly.

Mordanting the substrate: In order to charge the substrate to be dyed, potassium Aluminum
sulphate which is locally known as alum was used for the treatment. Two litres (2ls) of water
was filled in a pot, 1 table spoon (1 Tb) alum and 1tsp baking soda were added to it plus the
substrate. This was brought to a boiling point of 100˚C with constant starring and simmered for
two hours. The substrate (cotton Fabric) was allowed to cool off and soaked in the alum
solution overnight.

IJDSHMSS | Page 44
Methods of Dye Extraction
Cold Maceration
100gs of the sample (guinea corn leaves) was added to a beaker (500ml) containing 300ml of
distilled water and agitation was done at intervals for 48 hours for complete extraction. The
resultant mixture was filtered using cotton wool and filter funnel. Similar experiment was
conducted with acetone to compare the extraction power of the solvents. The temperature and
the PH of each extract was taken and recorded.

Soxhlet Extraction
The dried leaves of guinea corn were gathered, chopped into smaller pieces and measured
quantities of pulverized samples were fed into the soxhlet extractor. This method of extraction
is carried out when a compound of low solubility needs to be extracted from a solid mixture.
This technique places a specialized piece of glassware in-between a flask and a condenser. The
refluxing solvent repeatedly washes the solid extracting the desired compound into the flask.
The soxhlet extraction was carried out for colorant identification. Soxhlet extractor comprises
of the condenser, thimble, siphon tube, solvent tube, round bottom flask and the heating
mantle. 100g of each of the samples was measured into the thimble and 300ml of acetone was
added into the round bottom flask fitted into the thimble for extricable. The heating mantle was
on and extraction was done for 6 hours on the sample and the temperature for extraction was
56.05˚c on the sample which is the boiling point of acetone. The same procedure was used for
the extraction using water as solvent with a temperature of 100˚c. Several cycles of solvent were
run so as to extract all the compounds from the leaves. Rotary Evaporator was used to remove
excess solvent leaving the dye in dry state. The percentage yield, pH value and colour were
determined for the purified dye samples. See below

Sample of Dye Extract from Guinea Corn Leaves

Extraction Yield Percentage


The extraction yield was measured. This was done by measuring the solvent's efficiency to
specific components from the original material (Murugan and parimelahagan, 2014). This was
defined as the amount of extract recovered in mass compared to the initial amount of whole
plant. This was presented in percentage (%).

IJDSHMSS | Page 45
Dyeing Procedure
All the extracts were obtained in both aqueous and powdered form. 5g of the concentrated dye
from the leaves of the guinea corn was mixed with 100ml of distilled water and acetone
respectively for the dyeing process. The proportion of the fabric to be dyed with the dye
mixture were constant in all the operations. The measurement of the fabric were 47cm by
25cm. 100ml of the liquid dye was measured into a 250ml beaker, the fabric was submerged
into the beaker, the fabric heated between 40-60˚c and stirred approximately for 20 minutes
respectively. The dyed fabric was removed and aired for oxidation to take place for five
minutes. It was rinsed separately in running water and dried under a shade. See below

Samples of Dyed Fabric

Water Acetone Water Acetone


maceration maceration Soxhhlet Soxhlet

Colour Imparted on Food Substrate


Macaroni Colouring
10g of macaroni was washed and put in the pot. 1.0g of dry dye sample was measured into a
glass beaker, water was added and turned into the pot containing the pasta and stirred in order
to obtain a uniform colour. The cooking was done for ten minutes and the pasta allowed to
drain water very well. It was allowed for sometime to cool. See below

Yoghurt Drink Colouring


1.0g of the dry sample was mixed with 30 ml of water stirred very well and added to 170ml of
homemade yoghurt in a container corked and shacked very well for 10 minutes. A
homogenous mixture was formed with fine colour shade of blush as shown below

IJDSHMSS | Page 46
Batter
1.0g of dry sample was mixed with 10ml of water, stirred very well and added to the batter
stirring vigorously so as to mix very well in it. A well dispersed colour of blush was obtained as
shown below.

Result
Table 1: Cold Maceration Extraction of 100g of Material
Material Technique Temperature PH Time Yield
Guinea corn leaves Water 32˚c 5 48hours 38.6%
Maceration
Guinea Corn leaves Acetone 32˚c 5 48hours 49.8%
Maceration

Table 2: Soxhlet Extraction of 100g of Material


Material Technique Temperature PH Time Yield
Guinea Corn leaves Water 100˚c 5 6hours 52.1%
Soxhlet

Guinea Corn leaves Acetone 56.05 5 6hours 61.8%


Soxhlet

IJDSHMSS | Page 47
Table 3: Colour obtained with Different Solvents and method of Extraction
Material Technique Type of PH Temperature Colour observed Colour observed
textile after filtration after dyeing
Guinea Water white 5 32˚C Wine Blush
Corn maceration cotton
Leaves
Acetone white 5 32˚C Slightly reddish Brick
maceration cotton brown
Water white 5 100˚C Slightly deep Wine Deep blush
soxhlet cotton
Acetone white 5 56.05 Deep reddish Deep brick
soxhlet cotton brown

Table 1revealed that in water maceration the dye yield was 38.6% under 32˚C with PH 5 and the
time observed was 48 hours. For acetone maceration the yield was 49.8% maintaining the same
temperature and PH.

Table 2 showed result on soxhlet extraction. The water soxhlet of the plant at 100˚C within the
PH of 5 gave the yield of 52.1% and the time observed for the experiment was 6 hours. For
acetone soxhlet the temperature was 56.05 as the boiling point and the same PH and time was
maintained. It gave dye yield of 61.8%.

Table 3 revealed the colour obtained from different solvents and methods. For water
maceration, the colours observed after filtration and dyeing were wine and blush. In acetone
maceration it was slightly reddish brown and brick. The water soxhlet gave slightly deep wine
and deep blush after filtration and dyeing while acetone soxhlet gave deep reddish brown and
deep brick.

Food Colouring
Table 4: Colour Imparted on Substrate
Dye extract Technique Substrate Colour impart
Guinea corn leaf Water soxhlet Macaroni Blush
Flour
Batter Blush
Yoghurt Blush

Table 4 shows the different hues imparted on food such as macaroni, yoghurt, and batter. The
colours improved the facial value of these foods and drink. The harmless nature of the dye as
was extracted with distilled water and the nutrive values as having been researched by different
scholars could allow for these applications (Osabohien et al, 2013, FAO, 1995). The colour
obtained was blush in all the foods and drink. Table 9 answered research question 5.

Discussion
The dye sample from the heartwood of leaves of guinea corn was found soluble in distilled
water and acetone. It was observed that the dye concentration was high in the soxhlet
extraction. This supports the fact that soxhlet extraction is a very efficient form of extracting
colour from solid materials (Vankar, 2016). It may also be as a result of the temperature as the
heat of the solvent comes in contact with plant the extracting power was more efficient.
Temperature is the main factor which affects the extraction efficiency of dye from natural plant

IJDSHMSS | Page 48
(Kannanmarking, Uma and Rajarathinam, 2015). At higher a temperature water and acetone
was able to extract larger yield of natural dyes. The hues obtained by maceration using acetone
as the solvent gave brick and deep brick compared to maceration using water as solvent which
gave blush and deep blush . It also supports the fact that maceration is preferable used with
volatile solvents (Hans-Jorg Bart, 2016)

See Appendix 1.
The temperature of the various extracts were taken during extraction and dyeing. The variation
in temperature range was from 30-100˚c at PH 5. The variation in temperature range for
maceration was 32-60˚c while for soxhlet was 56-100˚c. The difference in temperature between
the distilled water and acetone is that acetone is very high in volatility (Usoro, 2001).

The colour observed after filtration and dyeing revealed distilled water plus sample in
maceration as blush, Acetone + Sample in maceration as brick, distilled water plus sample in
soxhlet as deep blush and acetone plus sample in soxhlet as deep brick.(See Table 3).

The colour imparted on food such as macaroni, batter and yoghurt drink contributed in
improving the appearance and nutritive values of the food and drink. This is in line with
Oyetayo and Ogunrotimi, (2012) and Osabohien (2014) that natural dye can be used to impart
colour on foods thereby improving the appearance for customers to patronize as well as enrich
the nutritive value..

Conclusion
This work showed that different hues of dye can be extracted from the leaves of Guinea corn.
The process of the extraction was eco-friendly. The dye hue obtained has the dyeing potential
which can be used as a source of textile dyeing. The colour shade can be obtained using
different methods and different solvents. The research work unveiled that their properties are
preferable to synthetic dye as they are not toxic. The use of mordant in textile application is
found to be fruitful to improving colour adherence and shades of the dyes. Guinea corn leaf is a
very good plant part that serves as a source of raw material for obtaining shades of wine red dye
that can be used for fabric dyeing in future. The study also unfolded the usefulness of dye
obtained from guinea corn leaf using water soxhlet technique as food colouring product.

Recommendations
The advantages of researching natural dyes and their application on textiles will improve the
art of creativity in the field of clothing and textiles. In view of the results of this study the
following recommendations are made.
1. The clothing and textile sections in secondary schools, colleges of education and
universities can use the result of the study as a resource material for teaching creative
skills in dyeing fabrics, fibres, yarns, tie-dye, batik etc.
2. Instructors should use the study to educate the students on the use of dye that is eco-
friendly.
3. The government should sponsor research work on natural dye exploration as this will
help to safe guard our environment from the damage caused by the use of synthetic
dyes.
4. It is recommended that dye obtained from guinea corn leaf should be used for food
colouring.

IJDSHMSS | Page 49
References
Acguah, S.B. & Oduro, K.A. (2012). Traditional cloth dyeing enterprise at ntons: challenges
opportunities. West African Journal Appl. Ecol 20 (1): 25-36.

Ekong, E.E (2016). Development, application and physical properties of printed textiles using Dyes
obtained Three Natural Plant sources. Unpublished project submitted to the Department
of Human Ecology, Nutrition and Dietetics, Faculty of Agriculture, University of
Uyo.

Earth Guild, (2016). Mordants, natural dyes, starter sets retrieved from www.earthguild.com-riff.
Mordant on 24\06\16.

FAO, (2001). Food analysis: food and agricultural association. Rome, Italy

FSD (2007). Food security department, sorghum, post-harvest operation compendium. London:
Macmillan Press.

Kultam, S. S. & Gokhale, A.V et al (2011). Cotton dyeing with natural dyes extracted from
pomegranate (Punica-granatum) peel. Universal Journal of Environment Research and
Technology. 1 (2), 135-139.

Mansour, H. (2013). Textile dyeing, environmental friendly usage orange extract on protein fabrics.
Retrieved from htt://dx.org.10.5772/54410 on 26\06\16.

Murugan, R. & Parimelahagan, T. (2014). Comparative evaluation of different extraction


methods for oxidant and anti-inflammatory properties from Osbecjia Parvifola Arn-
An in vitro approach. Journal of King Saud University 26 (4) 267-275. Retrived from
http://.

Malidi, S. & Altikriti, Y. (2010). Extraction of natural products. Retrieved from on 25/06016.

Neha, G. & Vidya, P. (2011). Extraction and application of natural dye preparations from the
floral parts of Woodfondia fruticosa (Linn) Kurz. India Journal of Natural Products and
Resources 2 (4): 403-408: India. Retrieved from nopr.niscair.res.in>bitstream.

Osabohien, E. (2009). The extraction and utilization of natural dyestuffs from dongoyaro
plant. Journal of the Chemistry Advancement Society. 7:184-190. Nigeria.

Osabohien, P. (2014). Extraction and application of dye stuff from the leaves of guinea corn
and onion skin. International Journal of Biological and Chemical Sciences. Retrieved from
http://ajol.info/index.php/ijbcs.com 20/02/17.

Otutu, J.O., Osabohien, E. & Efurhievive, E .M. (2010). Extraction of natural dyes for textiles
dyeing from the by-products of the timber industry. Biosci. Biotechnol Research. Abia: 7
(i): 87 – 92

Obenewaa, K., (2010). Extraction and application of plant dyes to serve as colourants for food and
Textiles. Published thesis submitted to the School of Gradnete Studies Kwame
Nkrumah University of Science and Technology, Kumah: faculty of Art, Colloge Art
and Social Science.
IJDSHMSS | Page 50
Oyetaya, F. L. & Ogunrotimin, A.I. (2012). Guinea corn (Sorghum Vulgere/leaf, a potential
source of nutrients and photochemical. Journal of Food and Puoloc Helath 2(6):228- 230

Sujata, L. & Raja, A.S. (2016). Natural dyes:Sources, chemistry, application and sustainability Issues.
Retrieved from on 21/06/16.

Thiyagarajan, S. Balakrishnan, K. & Tamilarasi, S. (2015). A study of extraction and dyeing


behaviour of natural dye obtained from cotton. Journal of Applied Chemistry 8:85 – 89.

Ugutuah, V. (2004). The Effect of different additions on the sensory qualities of waakiye, Ghana:
University of Ghana.

Usoro, E. S. (2001). The dyeing of textile fabrics with natural dyes from some local plants. unpublished
project submitted to the Department of Science Laboratory Technology Faculty of
Natural and Applied Science University of Uyo, Uyo.

Vankar, P. (2016). Natural dyes lecture No 9 department of chemistry Indian institute of technology.
Kanpur retrieved from textofvideo.nptel.iitm.ac.in>lec9 on 18/06/16.

Wanyama, P.A.G, Kiremire, B.T & Murumu, J.E.S. (2014). Extraction, characterization and
application of natural dyes from selected plants in Uganda for dye of cotton fabric.
African Journal of Plant Science 8(4) 185-195. Retrieved from http://www.acadenic
joirnals.org/AJPS.

Wipperlinger, M. (2004). About Mordants. Retrieved from www.eathnes.com on 20/06/16

IJDSHMSS | Page 51

You might also like