Akira LCT 27pbstp

LCD TV
Service Manual
-2 -
MODEL:
LCT-27PBSTP
Model No.: LCT-27PBSTP.doc
Version: 1.0
-3 -
CONTENTS
SAFETY PRECAUTION .............................................................................................................4
SPECIFICATION ........................................................................................................................6
APPEARANCE & CONTROL FUNCTION ...............................................................................11
ALIGNMENT INSTRUCTION ...................................................................................................16
SOFTWARE UPGRADING.......................................................................................................26
WORKING PRINCIPAL ANALYSIS ..........................................................................................29
BLOCK DIAGRAM....................................................................................................................30
IC BLOCK DIAGRAM ...............................................................................................................31
WIRING DIAGRAM...................................................................................................................34
ASSEMBLY LIST ......................................................................................................................35
TROUBLE SHOOTING GUIDE ................................................................................................41
APPENDIX ...............................................................................................................................49
CIRCUIT DIAGRAM
PARTS LIST
Version: 1.0
-4 -
IMPORTANT SAFETY PRECAUTION
Version: 1.0
-5 -
Version: 1.0
-6 -
SPECIFICATION
Screen Size & Type 597 x 336 mm
Net Dimension 700 x 230 x 582 mm
Gross Dimension 800 x 309 x 670 mm
Net Weight 19kg
Gross Weight 21kg

General
Power Consumption (Normal Operation) 140 Watts (MAX)
Power Consumption (Standby

3 Watts (MAX)
Operation)
Front Cabinet Colour Silver + Black
Back Cabinet Colour Grey 05
Stand Type / Colour Swivel / black+ silver
Power Adapter Input Voltage

Power Adapter
Power Adapter Output Voltage
Power Adapter Output Voltage No adaptor
Power Plug Type
Certification
Mains Voltage 100-240V

Built-In Power
Supply
Mains Frequency 50/60Hz
Power Plug Type 2.5-Amp round pin(VDE standard)
Operating Temperature 0 - 40 deg C

Operating
Spec
Storage Temperature -25 - -55degC
90% RH Max(Ta<=40 deg C& web-bulb
Relative Humidity Level temperature should be 39degC Max (Ta>40degC)
RF PAL I , B/G , D/K

Reception & Playback
RF SECAM B/G , D/K , L/L'

System
RF NTSC N/A
VIDEO PAL Yes
VIDEO SECAM Yes
VIDEO NTSC NTSC PLAYBACK 3.58 / 4.43
Version: 1.0
-7 -
Brand & Model CMO , V270W1-L04
Resolution 1280 x 720
Displayable Colour 16.7M
Hard coating(2H),Anti-reflective coating<less 2%

Surface Treatment
reflection
Viewing Angle (H/V) 170/170

Panel
Display Response Time 16.6ms
Contrast Ratio 900 : 1
Brightness 550cd/m2
Aspect 16:9
Lamp Life >=50,000
Bad pixels warranty (Bright / Dark /

Bright <2, Dark<5, total no more then 5 dot
Total)
Channel Coverage 40 - 870Mhz
Preset Channels 1 - 200

Tuner
S + Hyper Band CATV Yes
Aerial Input N/A
Detachable N/A
Comb Filter Yes 3D
Velocity Modulation N/A
Noise Reduction Weak / Medium / Strong
Film Theater N/A
Detail Enhancer Yes
Super Contrast N/A
Colour Transient Improvement Yes
Picture Mode Option 4 , Vivid / Standard / Mild / Customer

Picture
Brightness Control Range 0 to 100
Contrast Control Range 0 to 100
Colour Control Range 0 to 100
Sharpness Control Range 0 to 100
Hue Control -50 to 50
Colour Temp Selection 3 , Normal / Warm / Cool
Yes
Black Stretch
Version: 1.0
-8 -
Audio Output 6 Watts x 2
NICAM Stereo Yes
German A2 Stereo Yes
Surround No
Dual Sound Decoding Yes

Audio
Audio Mode Option 4 , Live / Pop / Rock / Customer
Volume Control 0 to 100
Treble Control -50 to 50
Bass Control -50 to 50
Balance Control -50 to 50
Auto Volume Level N/A
CVBS Input Yes / 1
S Video Input Yes / 1
Component YCbCr Input Yes / 1
Component YCbCr Displayable Modes 480i , 576i , 1080i
Progressive YPbPr Input Yes , 1
Component YPbPr Displayable Modes 480p , 576p, 720p
VGA D-15 Input Yes ,1

Terminals
PC Audio L/R Input Yes , No, earphone
SCART Input Yes , 2
SCART Output N/A
CVBS Output N/A
Optical Input N/A
Coaxial Input N/A
DVI Input N/A
Earphones Input Yes , 1
HDMI Input Yes , 1
Tele-text 1000 pages
All , (West Europe, East Europe, Turkish / Greek ,

Other Features
Tele-text Language
Cyrillic, Arabic)
PIP / POP / PBP(4 wins) on all terminal and 9 picture

P in P Type
browse on TV
Number of Tuner 2
Channel Scan Auto / Manual
Version: 1.0
-9 -
Display Aspect Ratio Control Auto / 16:9 / 14:9 / 4:3 / zoom
OSD Language OSD with Chinese , English, Russian, Turkish
Other Menu Feature OSD background
Screensaver No
Timer On Yes
Timer Off Yes
Sleep Timer Yes 15,30,45,60,90,120 min
Auto Shutdown When No Signal 5 min
Picture Freeze Yes
Child Lock Yes
Prog+ , Prog- , Vol+ , Vol- , Menu , TV/AV , Main

Local Keys
Switch
Instruction Manual Lang English, Russian
Auto Tuning Yes
Manual Tuning Yes
Manual Fine Tuning Yes

Installation
Manual/Auto Colour Sys Both
Manual/Auto Sound Sys Both
Program Naming Yes
Skip Channel Yes
Exchange Channel Yes
Copy Channel Manual sort program
Remote Control Yes
Batteries for RC Yes
Euro 2 Pin Power Plug No
3 Pin Power Plug No
Instruction Manual Yes

Accessories
Warrantee Card Yes , Russian
RF Cable Yes
S-Video Cable No
CVBS Cable No
VGA Cable No
SCART Cable No
DVI Cable No
Version: 1.0
-10 -
HDMI Cable No
Optical Cable No
Coaxial Cable No
Wall Mounting Bracket Yes
Specification are subject to changes without prior notice.
Version: 1.0
-11 -
APPEARANCE & CONTROL FUNCTION
Version: 1.0
-12 -
MAIN UNIT
Version: 1.0
-13 -
REMOTE CONTROL
Version: 1.0
-14 -
Version: 1.0
-15 -
Alignment Instructions
1. Test equipment
PM5515 (Video signal generator)
PM54200(SCART signal generator)
VG-848(YUV, VGA and DVI signal generator)
K-7253 (VGA signal generator)
CA210 (White balancer)
2. The alignment flow chart (see below figure)
Version: 1.0
-16 -
3 Unit adjustments
Method for entering factory menu: Press MENU → -/--→9→1→8 one by one, then enter
factory menu, press the SLEEP button to select adjustment page, exit factory menu to press
the MENU button.
4 EEPROM initialization
Enter the first page of factory menu, select “EEPROM INITIALIZE” to be “on”, after turn off the
unit, repeating turn on the unit is over.
5 white balance adjustment

Input PAL signal of 16-level gray-scale (TIMING969 PATTAN921) from VG848 to AV channel,
enter user menu, set color to 0, APL to “off”, enter factory menu white balance adjustment
page, select color temperature, fixed the GGAIN to 50H, adjust BGIAN and RGAIN to 400nits,
then the color coordinate to 284, 299. Fixed the BOFFSET to 50H, adjust GOFFSET and
ROFFSET to 5nits, then the color coordinate to 284, 299. Select cool tint, adjust color
coordinate to 270, 283. Select warm tint, adjust color coordinate to 313, 329.
6. Performance Inspections
6.1 TV function
Enter the search menu → auto search, connect RF-TV terminal to the central signal source,
check if there is station skipping.
6.2 AV/S input terminal

Input AV/S signal, check the picture and sound is normal
6.3 SCART terminal (note: check the SCART terminal, set display mode to AUTO)
6.3.1 Check SCART INPUT special function
6.3.1.1 SCART1 terminal function
a. After turn on the unit, connect the SCART1 to PM54200 signal generator, then the unit
auto select to SCART1 mode.
b. SCART signal generator sends CVBS signal to the unit, check if the image and sound
is normal. It sends image format (16:9 and 4:3) to the unit, check if the unit auto identify is
normal. Change SCART signal to RGB signal, check if the image and sound is normal, It
sends image format (16:9 and 4:3) to the unit, check the unit auto identify is normal. Select the
PIP mode, connect earphone cable, and check if the sound is normal.
Version: 1.0
-17 -
a. After turn on the unit, connect the SCART2 to PM54200 signal generator, then the unit
auto select to SCART2 AV mode.
b. SCART signal generator sends CVBS signal to the unit, check if the image and sound
is normal. It sends image format (16:9 and 4:3) to the unit, check if the unit auto identify is
normal, and display the SCART2 AV. Change SCART signal to Y/C signal, select the SCART2
Y/C channel mode, check if the image and sound is normal, It sends image format (16:9 and
4:3) to the unit, check if the unit auto identify is normal. Select the PIP mode, connect
earphone cable, and check if the sound is normal.
6.3.2 Check SCART OUTPUT special function

Input signal in the TV states, connect the SCART1 terminal to the TV. Change the TV program,
check if output signal of SCART1 is TV signal, and the image and sound is normal, change the
unit channel, the CART1 output TV signal, it can not other signal.
Input signal in the TV/AV/S states, connect the SCART2 terminal to the TV. Change the unit
channel, check if output signal of SCART2 is current signal, and the image and sound is
normal.
6.4 YPbPr/YPbPr terminal Input the YUV signal (VG-848 signal generator), separate input
YUV format signal of table 1, check if the image and sound is normal. If the image is deflection
of the H-field, select auto sync correction of the SCREEN menu. If the image is slight disturb,
adjust the FINE TUNE correction of the SCREEN menu. Open the PIP mode, connect the
earphone, and check if the image and sound is normal.
Table 1 YUV Signal Format
H-frequency(kHz) V-frenquency(Hz) Signal

1 15.734 59.94 SDTV 480i
2 31.469 59.94 HDTV 480p
4 44.955 59.94 HDTV 720p
6 33.716 59.94 HDTV 1080i
7 15.625 50 SDTV 576i
8 31.25 50 HDTV 576p
9 33.75 50 HDTV 1080i
10 37.50 50 HDTV 720p
6.5 VGA terminal Input the VGA signal (VG-848 signal generator), separate input VGA
Version: 1.0
-18 -
format signal of table 1, check if the image and sound is normal. If the image is deflection of
the H-field, select auto sync correction of the SCREEN menu. If the image is slight disturb,
adjust the FINE TUNE correction of the SCREEN menu. Open the PIP mode, connect the
earphone, and check if the image and sound is normal.
6.6 HDMI terminal HDMI signal format receive the three high definition signal: 480P,
576P,720P/50/60 Hz, 1080I/50/60 Hz, except for the table 2 signal. Check if the image
(contain HDCP ON and OFF) and sound is normal. If the image is deflection of the H-field,
select auto sync correction of the SCREEN menu. Open the PIP mode, connect the earphone,
and check if the image and sound is normal.
TABLE2 VGA Signal Format
Point clock pulse

Resolution H-Frequency(kHz) V-Frenquency(Hz) Remark
Frenquency(MHz)
1 720 X 400 31.469 70.086 28.322 IBM
2 640 X 480 31.469 59.94 25.175 IBM
3 640 X 480 37.861 72.809 31.5 VESA
4 640 X 480 37.5 75 31.5 VESA
5 640 X 480 43.269 85.008 36 VESA
6 800 X 600 35.156 56.25 36 VESA
7 800 X 600 37.879 60.317 40 VESA
8 800 X 600 48.077 72.188 50 VESA
9 800 X 600 46.875 75 49.5 VESA
10 800 X 600 53.674 85.061 56.25 VESA
11 1024 X 768 48.363 60.004 65 VESA
12 1024 X 768 56.476 70.069 75 VESA
13 1024 X 768 60.023 75.029 78.75 VESA
14 1280 X 1024 63.98 60.02 108.00 VESA
15 1024 X 768 68.667 84.98 94.486 VESA
Version: 1.0
-19 -
6.7 Ex-Factory setting see to TABLE 3 -TABLE 9 TABLE 3 Factory Option Menus
Items Ex-Factory setting
IIC Bus-off Off

EEPROM Erase Off
Backlight Adjustable Off
Back Light 100
Menu Timeout 5
Blank switch enable On
ShowLogo On
Auto Program Sort On
West Europe / East Europe / Cyrillic
TT Char Group
/ Turkish /Greek/Arabic/Hebrew
Dynamic Scart Off
Note: the latter 6 items should set according to clients’ require.
Version: 1.0
-20 -
TABLE 4 Factory Audio Setting TABLE 5 Factory Video Limit Setting
Ex-Factory setting
Items
LCT-27PBSTP LCT-32PBSTP LCT-37PBSTP LCT-42PBSTP
Volume 1 2CH 2CH 2CH 2CH
Volume 25 55H 57H 5AH 5AH
Volume 50 5CH 5EH 61H 61H
Volume 75 64H 65H 69H 69H
Volume 100 6BH 6DH 72H 72H
HP VOLUME SETTING
Volume 1 64H
Volume 25 96H
Volume 50 A1H
Volume 75 AEH
Volume 100 BEH
MSP Scart1
72H
Volume
Prescale Scart 4CH
Prescale FM/AM 27H
Prescale Nicam 64H
Scart TV Volume 20H
Scart AV Volume 72H
D/K select HDEV3 Off
AVC Off
Equalizer Bands
60H
Max
Spatial Mode 0
Spatial Strength 00H
Version: 1.0
-21 -
Items CVBS SC-RGB YPBPR D-SUB HDMI

Bright Min D5H CFH C7H CFH D2H
Bright Middle 00H 00H 03H 05H 07H
Bright Max 38H 3DH 34H 3DH 31H
Contrast Min 09H 09H 09H 09H 08H
Contrast Middle 20 25H 20H 25H 23H
Contrast Max 2AH 31H 29H 31H 2CH
Sharpness Min 00H 00H 00H 00H 00H
Sharpness Middle 10H 10H 10H 10H 10H
Sharpness Max 1FH 1FH 1FH 1FH 1FH
Color Min 00H 00H 00H 00H 00H
Color Middle 1DH 1DH 1DH 1DH 1DH
Color Max 2DH 2DH 2DH 2DH 2DH
Hue Min 80H 80H 80H 80H 80H
Hue Middle 20H 20H 20H 20H 20H
Hue Max 7FH 7FH 7FH 7FH 7FH
Version: 1.0
-22 -
TABLE 6 White Balance Adjust TABLE 7 Image analog setting TABLE9 SOUND
equilibrium value setting
ITEMS LCT-27PBSTP LCT-32PBSTP LCT-37PBSTP LCT-42PBSTP

R Offset 55 55 54 53
G Offset 51 53 57 49
B Offset 50 50 50 50
R Gain 42 36 36 37
G Gain 50 50 50 50
B Gain 21 40 51 38
Brightness 51 51 51 51
Contrast 100 100 100 100
Color Temperature Standard
R Offset 60 59 58 55
G Offset 55 55 58 52
B Offset 50 50 50 50
R Gain 35 25 24 32
G Gain 50 50 50 50
B Gain 28 48 61 48
Contrast 100 100 100 100
Color Temperature Cold
R Offset 55 49 49 44
G Offset 53 51 53 47
B Offset 50 50 50 50
R Gain 62 51 58 66
G Gain 50 50 50 50
B Gain 8 23 33 22
Contrast 100 100 100 100
Color Temperature Warm
Version: 1.0
-23 -
CVBS Vivid Standard Mild Custom

Contrast 90 80 50 80
Color 70 60 40 60
Hue 00 00 00 00
Sharpness 60 50 30 50
SC-RGB Vivid Standard Mild Custom
Color 80 65 40 65
Hue 00 00 00 00
YPBPR Vivid Standard Mild Custom
Color 80 65 40 65
Hue 00 00 00 00
D-SUB Vivid Standard Mild Custom
Color 80 65 40 65
Hue 00 00 00 00
HDMI Vivid Standard Mild Custom
Color 80 70 40 70
Hue 00 00 00 00
Note: in factory menu states, it can change the factory mode to value of the image and sound, else select the image
and sound balanced value in the other states.
Version: 1.0
-24 -
Live Pop Rock Custom

120 Hz 50 50 65 50
500 Hz 50 50 55 50
1.5 kHz 50 60 55 50
5 kHz 80 70 55 50
10 kHz 85 70 55 50
6.8 Ex-factory setting of user menu

6.8.1 select TV channel
6.8.2 video menu, Mode: Standard, NR: Medium, APL:ON
6.8.3 sound menu, Volume: 20, Balance: 00, Equalizer: Custom, HP Volume: 20;
6.8.4 edit menu, Color System: Auto, Sound System: DK;

6.8.5 option menu, Default Zoom: Auto, Child Lock: Off, Menu Language: English, Country:
UK, WSS: OFF, Blue Screen: On.
Note: the 6.8.4 and 6.8.5 items should set according to clients require.
Version: 1.0
-25 -
Software Upgrading
1. Enter the software upgrading state of the TV Method 1: press the VOL- button in the unit,
turn on the main power switch, then the screen display black screen, but the indicator to blue.
Method 2: Enter factory menu, select the IIC-BUS OFF item.
2. Connection upgrading tools with upgrading port.
3. Dual- click IAPWriter logo, enter the upgrading states (if the PC and the IIC communication
trouble, it can prompt.
4. Select the file menu load the software follow as:
Version: 1.0
-26 -
5. Select WRITE DEVICE item of the device menu, till the right screen display “DONE”.
6. Turn off the power , restart the unit.

Note: because of the software, it may be no-stabilization, the software can auto download
and write.
Version: 1.0
-27 -
NOTE: Do not shut the power off or turn the TV set on during the FLASH write.
Otherwise it may lead to no way for flash to rewrite.
Version: 1.0
-28 -
Working Principle Analysis

1. Analog signal flow
Antenna reception signal send to integrative tuner (contain HF and IF amplifier circuit), the
tuner is controlled the command (SDA and SCL) of the MCU N301 (M16C), select appropriate
channel to system switch, via HF amplifier and IF amplifier decode, output video signal of
2VPP and sound signal of 1VPP.
Sound signal (SCART1, 2 sound, AV sound, YPbPr, HDMI and D-SUB) via N581 HEF4052BT
(sound diverter switch) to output signal, it send to N801(MPS3410 sound processing and
volume control) switch of audio. Select right/left sound channel, their send to digital sound
amplifier N803 (TPA3008) amplify, then send to speaker.
After output video signal of tuner, SCART1 video signal and RGB signal via matched
resistance, the signal thought alone channel send to main decode IC(N101 SVP-EX52) video
switch, A/D transition, digital decode, image scale and OSD superposition, then send to LVDS
level drive for LCD screen.
AV, S-Video, SCART2 video and Y/C signal thought matched resistance, the signal send to
the N506 video switch (SN74CBT3257CDR), via switching to selected signal (EX52_Y and
EX52_C) to main decode IC (N101 SVP-EX52) video switch, A/D transition, digital decode,
image scale and OSD superposition, then send to LVDS level drive for LCD screen.
D-sub and YPbPr signal thought matched resistance, the signal send to the N507 video switch
(SN74CBT3257CDR), via switching to selected signal (EX52_YUV) to main decode IC (N101
SVP-EX52) video switch, A/D transition, digital decode, image scale and OSD superposition,
then send to LVDS level drive for LCD screen.
2. Digital signal flow:HDMI signal thought HDMI reception chip N405 (SiI9011HDMI with
HDCP function), after receive, output digital format signal send to SVP-EX52 PIP channel
thought image scale and OSD superposition, then send to LVDS level drive for LCD screen.
The HDMI chip output audio digital format signal change to analog sound signal from N403
(CS4344 audio DA transfer chip), then N581 switched to N801 (MPS3410 sound processing
and volume control).
3. TELETEXT function
This unit adopt main decode IC N101(SVP-EX52) of Trident company, it has TELETEXT
decode function, after decoded, the teletext information in OSD display.
Version: 1.0
-29 -
BLOCK DIAGRAM
Version: 1.0
-30 -
IC Block Diagram
1. Sound processing IC (MSP3410)
Sound signal send to sound processing N801 MSP3410, and dual-circuit tuner has second
SIF, it sends to N801 (stereo decode and auto volume control), N801 has audio channel
switch, after switching in N581 (HEF4052BT), the audio input of VGA/HDMI/YPbPr will be sent
to N801 together with the audio signal of TV and AV to do the switching process. A way signal
thought volume and high-low sound controlled, output the left and right audio send to digital
audio amplifier N803 (TPA3008) amplify, then it send to speaker, other way signal output
left-right audio send to earphone amplifier N805 (NJW1109), after audio control and power
amplifier, it output to earphone socket. Other two ways signal output audio of TV out and AV
out by SCART terminal of video board. MSP3410 internal block diagram as follow:
Main pins instructions:

2, 3: SCL, SDA 27, 28: left-right audio of audio power amplification 36, 37: left-right audio of
earphone 24, 25: left-right audio of AV OUT 33, 34: left-right audio of TV OUT 47, 48: left-right
audio from main board 50, 51: left-right audio of SCART2 53, 54: left-right audio of SCART1 56,
57: left-right audio of AV IN 67, 69: SIF input of sub-channel and main-channel TV
59: MONO input of sub-channel TV
2. Sub-channel and SCART video signal decode IC (TVP5147)

Sub-tuner TUNER202 decode video, AV, S-VIDEO, SCART1 video, SCART2 video and Y/C
signal, after matching impedance, enter decoding IC N601 (TVP5147), so the PIP image of
sub-channel can selecting arbitrary video signal.
Version: 1.0
-31 -
MSP3410 internal block diagram as follow:
TVP5147 main pins instructions:

28, 29: SCL, SDA
22: Video input for SCART1 7, 80: Y/C signal input for SCART2
16: video signal input of sub-tuner
8: Y signal input of AV or S-Video
1: C signal input of S-Video
9, 2, 18: YUV signal input of compatible DTV
Version: 1.0
-32 -
3. Reception HDMI signal (SiI9011)

After differential signal of HDMI send to N405 (SiI9011), then it transform 24bit for video digital
signal, and sent to IC N101 (SVP-EX52) processing.
SiI9011 internal block diagram as follow:
Version: 1.0
-33 -
4. Main decode and processing IC(DPTV-SVP-EX52) SVP-EX52 internal block

diagram as follow:
SVP-EX52 main pins instructions:

14, 16: SCL, SDA
10, 11: VGAHS, VGAVS input,
244, 231: EX52_Y and EX52_C input
243: main tuner video signal input
242: video signal input for Scart1
226, 248, 233: Scart1 RGB input
246, 232, 225: EX52_YUV input
236, 237: video output for SCART2
Version: 1.0
-34 -
Wiring Diagram
Control Button
Power Supply
DATA PCB
Audio PCB
“R” Speaker “L” Speaker
Video PCB
IR Board

Version: 1.0
-35 -
Assembly List
Name Part No. Main IC and No.
Data processing board 667-L27W18-69 N101 DPTV-SVP-EX52 (353-DPTV0-20)
N201 K4D2632838F (353-26323-10)
N302 W29C040P-90B (353-29040-30)
N301 M30620SPGP (353-30620-20)
N601 TVP5147PFP (353-51470-10)
N405 SiI9011CLU (353-90110-10)
N403 CS4344CZZ (353-43440-10)
Audio processing board 667-L27W18-15 TUNER201 JS-6B2/122A2-A2 (590-40512-00)
TUNER202 JS-6B2/121A2 (590-40511-00)
N801 MSP3410G (353-34100-80)
N803 TPA3008D (353-30080-10)
N805 NJW1109M (353-11092-20)
Video processing board 667-L27W18-40
IR reception board 667-L27W18-09
(LC-27W18S)
Button board 667-L27W18-05
(LC-27W18S)
667-L32W25-05
(LC-27W25S)
Power supply board 667-L27W18-20
Version: 1.0
-36 -
Identification criteria for the bright spot and dark spot of the LCD screen
Notes:
1 Definition of defected point (bright spot, dark spot): It is identified as a defected point
if its area exceeds 1/2 of a single picture element (R, G, B).
2 Definition of bright spot: It is identified as a bright spot if it is bright in the state of dark
field and its bright size remains unchanged
3 Definition of dark spot: It is identified as a dark spot if it is dark in the state of white
field and its dark size remains unchanged
4 Definition of two neighboring points: Defects of a group of picture elements (RB,RG,GB).
Version: 1.0
-37 -
TROUBLE SHOOTING
1. Fault clearance
Before servicing please check to find the possible causes of the troubles according to the table
below:
1.1 Antenna (signal):
Picture is out of focus or jumping Bad status in signal receiving Poor signal Check if there are
failures with the electrical connector or the antenna.
Check if the antenna is properly connected.
Fringe in picture Check if the antenna is correctly oriented. Maybe there

is electric wave reflected from hilltop or building.
Picture is interfered by Possibly due to interference from automobile, train, high

stripe shaped bright spots voltage transmission line, neon lamp etc. Maybe there is
interference between antenna and power supply line.
Please try to separate them in a longer distance.
Maybe the shielded-layer of signal wire is not connected
properly to the connector.
There appear streaks or Check if interfered by other equipment and if interfered

light color on the screen possibly by the equipment like transmitting antenna,
non-professional radio station and cellular phone.
Version: 1.0
-38 -
1.2 TV set:
Symptoms Possible cause

Check to see if the power plug has been inserted properly
Unable to switch the power on
into the socket.
Check to see if the power supply of liquid crystal TV has

been switched on. (As can be indicated by the red LED at
the front of the TV set) See if it’s receiving the signal that is
No picture and sound transmitted from other source than the station Check if it’s
connected to the wrong terminal or if the input mode is correct.
Check if the signal cable connection between video frequency
source and the liquid crystal TV set is correct.
Deterioration of color phase or

Check if all the picture setups have been corrected.
color tone
Screen position or size is not
Check is the screen position and size is correctly set up.
proper
Picture is twisted and deformed Check to see if the picture-frame ratio is properly set up.
Check the “Component” or “RGB” settings of the liquid
Picture color changed or colorless Crystal TV set and make proper adjustment according to
signal types
Check if the contrast setting is too high. Possibly the output

Picture too bright and there is quality of DVD broadcaster is set too high. It maybe also
distortion in the brightest area due to improper terminal connection of the video frequency
signal in a certain position of the system.
Picture is whitish or too bright Check if the setting for the brightness is too high Possibly the
in the darkest area of the picture brightness grade of DVD player (broadcaster) is set too high.
No picture or signal produced

Check if the cable is disconnected. Check if it’s connected
from the displayer if “XXX in
to the proper terminal or if the input mode is correct.
search” appears.
Check if the TV set can receive input signal. The signal is not
There appears an indication –
correctly identified and VGA format is beyond the specified
“outside the receivable scope)
scope.
Version: 1.0
-39 -
Check if the batteries are installed in the reverse order. Check

if the battery is effective. Check the distance or angle from the
Remote control cannot work
monitor. Check if there is any obstruct between the remote
properly
control and the TV set. Check if the remote control signal-
receiving window is exposed to strong fluorescence.
No picture and sound, but only Check if the antenna cable is correctly connected, or if it has
hash. received the video signal correctly.
Check if the antenna cable is correctly connected. Of if it has
Blur picture
received the right video signal.
Check if the “mute” audio frequency setting is selected. Check
if the sound volume is set to minimum. Make sure the
No sound
earphone is not connected. Check if the cable connection is
loose.
When being played or in pause VHS picture search tape
sometimes can’t provide stable picture, which may lead to
When playing VHS picture search
incorrect display of the liquid crystal TV, In this case please
tape, there are lines at the top or
press “auto” key on the remote control so as to enable the
bottom of the picture.
liquid crystal TV set to recheck the signal and then to display
correct picture signal
Version: 1.0
-40 -
TROUBLE SHOOTING GUIDE
Version: 1.0
-41 -
Version: 1.0
-42 -
Version: 1.0
-43 -
Version: 1.0
-44 -
Version: 1.0
-45 -
Version: 1.0
-46 -
Version: 1.0
-47 -
Version: 1.0
-48 -
Version: 1.0
-49 -
APPENDIX
Version: 1.0
-65 -
PARTS LIST
PART No. Description Quantity
335-27001-00 PANEL V270W1-L04 ! 1
360-30042-00 POWER SWITCH HF-606 ! 1
364-42201-00 SOCKET WP2-9C 2
485-10171-00 POWER CARD 300+LASR-24 ! 1
605-L27X183-01 SPEAKERS INSTALLATION GUIDE 1
615-1A526-00A PANEL HOLDER ASS'Y 1
615-10545-00A WALL BRACKET ASS'Y 1
655-B1202-54 (12-PINS) LEAD WITH HOUSING 1
655-33901-13 (3-PINS) LEAD WITH HOUSING 1
655-4E302-101 (4-PINS) LEAD WITH HOUSING 1
655-6E302-69 (6-PINS) LEAD WITH HOUSING 1
655-61201-125 (6-PINS） LEAD WITH HOUSING 1
655-71202-80 (７-PINS） LEAD WITH HOUSING 1
655-74302-30 (7)-PINS LEAD WITH HOUSING 0.5
655-74302-30 (7)-PINS LEAD WITH HOUSING 0.5
665-D0002-589 LVDS CABLE 30-PINS 1
700-60255-100 LED-CONDUCTOR 1
743-1B180-8A1 KEY DECORATION 1
743-10181-00 LED-CONDUCTOR DECORATION 1
770-189B0-79 UL2468 20# 180mm 2
780-X18RH-AF2 BACK CABINET 1
808-1A841-AF0A AV INTERFACE BOARD ( LEFT ） 1
808-1A842-AF0 AV INTERFACE BOARD ( RIGHT ） 1
808-10812-AF0 POWER CARD COVER 1
808-10829-AF0 BOTTOM CONNECTING COVER 2
808-10833-AF0 BACK CABINET RIGHT COVER 1
808-10835-AF0 BACK CABINET LEFT COVER 1
808-10836-AF0 ROTATION AXIS COVER 1
808-10837-AF0 DECORATION COVER 4
808-10840-AF0A KEY COVER 1
808-70361-00 INSULATION INTERFACE 1
808-80265-01 CONDUCTIVE GASKET(18X14X60) 4
Version: 1.0
-66 -
851-23008-14 SCREW SJ2824 ST3X8-Y 4
851-23008-14 SCREW SJ2824 ST3X8-Y 4
851-23010-14 SCREW SJ2824 ST3X10C-Y 4
851-23010-14 SCREW SJ2824 ST3X10C-Y 14
851-23010-14 SCREW SJ2824 ST3X10C-Y 2
851-23010-14 SCREW SJ2824 ST3X10C-Y 2
851-23012-14 SCREW SJ2824 ST3X12C-Y 4
851-43010-14 SCREW F(+)T3x10A-Y 2
851-43010-14 SCREW F(+)T3x10A-Y 2
851-53008-31 SCREW SJ2825 ST3X8FT D.Zn 2
851-53012-14 SCREW SJ2825 ST3X12C-Y 2
852-23006-81 SCREW SJ2829 M3X6-D.Zn 4
852-33008-85 SCREW B(+) M3X8- 1
852-43006-84 SCREW F(+) M3X6-Y 2
852-43006-85 SCREW F(+)M3X6- 3
852-43010-84 SCREW F(+) M3X10-Y 2
852-53006-81 SCREW SJ2830 M3X6-D.Zn 2
852-53006-81 SCREW SJ2830 M3X6-D.Zn 1
852-53006-81 SCREW SJ2830 M3X6-D.Zn 7
852-53006-81 SCREW SJ2830 M3X6-D.Zn 4
852-53006-81 SCREW SJ2830 M3X6-D.Zn 4
852-53006-81 SCREW SJ2830 M3X6-D.Zn 4
852-53006-81 SCREW SJ2830 M3X6-D.Zn 1
852-53008-81 SCREW SJ2830 M3X8-D.Zn 4
852-54010-81 SCREW SJ2830 M4X10-D.Zn 8
852-54016-84 SCREW SJ2830 M4X16-Y 8
857-10002-09 COTTON FLANNEL 4
859-11302-00 BACK LIGHT STRIPE 1
863-81369-00A POLY FOAM (TOP ,BOTTOM ) 1
863-81370-00 POLY FOAM (BOTTOM ,BOTTOM ) 1
870-10156-00 BRACKET ( LEFT ） 2
Version: 1.0
-67 -
870-10157-00 BRACKET ( RIGHT ） 2
870-10285-AM0 POWER SOCKET BRACKET 1
870-3A183-AF0 USB BRACKET 1
870-30185-030 LIGHT CONDUCTOR BRACKET ( DARK GRAY ） 1
881-63071-00 GROUND PROTECTION LABEL 1
886-31021-00 ACCESSORIES BOX(15L) 1
887-20047-01 ACCESSORIES PALSTIC BAG 1
887-21163-P0 PALSTIC BAG (1100X800) 1
894-30030-11 WASHER GB97.1-85-3-140Hv-D.Zn 2
894-40030-14 WASHER GB859-87 3 DZn 2
364-93222-00 AV JACK EV-021F-AV3 2
485-10171-00 POWER CARD 300+LASR-24 ! -1
485-10199-00 POWER CARD SW198+LASR-24 ! 1
488-10012-00 BATTERY 7# 2
604-L27W18S3-02 I/M 1
605-L27X183-02 WALL BRACKET INSTALLATION GUIDE 1
665-D0002-156 RF CABLEΦ9.5(m)-Φ9.5(m) 1
780-X18W0-1C1 FRONT CABINET 1
880-10815-B1 FRONT LOGO 1
881-62875-165 BACK PLATE LABEL LCT-27PBSTP,AKIRA 1
881-80847-00 WRRANTY CARD (AKIRA) 1
886-31842-040WA CARTON BOX (LCT-27PBSTP,AKIRA) 1
301-IL27W18-02G RC-I02-0GREMOTE CONTROL UNIT ASS'Y 1
615-1A288-00A WALL BRACKET ASS'Y 1
852-34008-81 SCREW B(+) M4X8-D.Zn 6
855-B0016-00 EXPANSION BOLT M8X72 4
855-C4030-00 SCREW 4X30 10
886-31511-00 WALL BRACKET BAGS 1
887-21167-00 WALL BRACKET ACCESSORIES BAG 1
615-10495-00B ROTATION AXIS ASS'Y 1
742-30091-00 TIE 1
808-10742-0G0 POST COVER BOARD （FRONT） 1
808-10830-0G0 POST COVER BOARD (BACK） 1
808-10843-AC0A TV STAND FIXING BOARD 1
808-10928-8A0 TV STAND FACE PLATE 1
Version: 1.0
-68 -
820-20052-00 COUNTERWEIGHT BOARD 1
851-43008-14 SCREW F(+)T3x8A-Y 9
851-43008-14 SCREW F(+)T3x8A-Y 1
851-43008-14 SCREW F(+)T3x8A-Y 1
851-43040-14 SCREW SJ2825 ST3X40C-Y 1
851-44012-57 SCREW F(+)4X12G-D.Zn 4
851-44012-57 SCREW F(+)4X12G-D.Zn 4
868-20478-00A CUSHION 8
870-4D202-0G0A UPRIGHT POST( SILVERY WHITE 06) 1
364-42201-00 SOCKET WP2-9C 2
384-20507-81 SPEAKER ST50-05 4
384-21912-W0 SPEAKER ST13-Q09 2
665-D0002-593 SPEAK WIRES 120mm 2
808-10831-0G0 FRONT COVER OF SPEAKERS 1
808-10832-AF0 BACK COVER OF SPEAKERS 1
808-70255-00 EVAGLUE （75X30X1.5) 1
808-70259-00 EVAGLUE (25X15X2) 1
808-70259-00 EVAGLUE (25X15X2) 1
808-70367-00 EVAGLUE (900X4X1) 2
851-23008-14 SCREW SJ2824 ST3X8-Y 4
851-23010-14 SCREW SJ2824 ST3X10C-Y 4
851-23010-14 SCREW SJ2824 ST3X10C-Y 12
851-23012-14 SCREW SJ2824 ST3X12C-Y 4
851-53008-14 SCREW SJ2824 ST3X8C-Y 16
870-10276-00 SPEAKERS CONNECTING PARTS 2
887-21270-00 PALSTIC BAG (150X900) 1
340-00168-00 DIODE UF4007 1
340-00168-00 DIODE UF4007 1
340-00237-003 DIODE FR105(P) 1
340-00270-00 DIODE 1N5819 1
340-00345-00 DIODE P6KE200A 1
340-00403-00 DIODE SF10L 60U 1
340-00424-00 DIODE MBRF20150CT 1
340-00424-00 DIODE MBRF20150CT 1
340-80028-00 *RECTIFIER U8KBA80R 1
Version: 1.0
-69 -
343-00600-70 TRANSISTOR FQPF 12N60C 1
343-00600-70 TRANSISTOR FQPF 12N60C 1
352-02650-10 IC TNY265P 1
352-08170-50 IC H11A817C (D) 1
364-331CK-00 3-PINS CONNECTORS FF-A3963-WV-2 1
364-77511-00 FUSE HOLDER 2
459-B233M-70 CERAMIC CAPACITOR ECKDNS332ME ! 1
459-5122K-00 CERAMIC CAPACITOR RQC05B221K-H46CA 1
459-5222K-00 CERAMIC CAPACITOR RQC10B222K-H46CA 1
459-6247K-00 CERAMIC CAPACITOR DE1205B472K1K 1
459-6310R-00 CERAMIC CAPACITOR DE1510E103Z1K 1
462-2B422-M0V POLYESTER CAP 250VAC-0.22uF-M ! 1
462-25447-H1 POLYESTER CAP CL21-400V-474J-P15(II 1
462-25447-H1 POLYESTER CAP CL21-400V-474J-P15(II 1
464-DE610-M0 ELECTROLYTIC CAP CD110H-25V-10uF-M 1
464-DE810-M1 ELECTROLYTIC CAP CD81-25V-1000uF-M 1
464-DF722-M0 ELECTROLYTIC CAP CD110H-35V-220uF-M 1
464-D7710-M0G ELECTROLYTIC CAP CD288H-400V-100uF-M 1
467-2FA47-H0 METAL RESISTOR 1W-4.7Ω-JL 1
467-2H147-H0A METAL RESISTOR 3W-470Ω-J 1
467-2H356-H0D METAL RESISTOR 3W-56kΩ-JL 1
467-6HB15-H0A WIRE ROUND RESISTOR RX21-3W-0.15Ω-J 1
467-6HB33-H0 WIRE ROUND RESISTOR RX21-3W-0.33Ω-JL 1
467-8E510-H0A SOLID RESISTOR 1/2W-1MΩ-J ! 1
469-40004-00 THERMISTOR 5D2-14LC ! 1
470-00341-00 SWITCHING TRANSFORMERSRW16ES-X70V113 ! 1
470-00388-00 SWITCHING TRANSFORMERBCK-100-02B1 ! 1
477-20076-00 LINE FILTER TF1409F-122Y2R0-X 1
477-20079-00 LINE FILTER TF1807F-103Y2R0-X0 1
477-40189-00 FIXED COIL LI050 1
Version: 1.0
-70 -
477-40252-00 FIXED COIL SF-T8-45I-X01 1
477-40265-00 FIXED COIL SRW3019C-X03V101 1
569-03145-00 #FUSE 20T 2A 250V UL ! 1
569-14141-80 FUSE 50T 4AL 250V ! 1
569-22155-00 FUSE 250V 5A ! 1
655-21101-08 （2-PINS） LEAD WITH HOUSING 1
666-13511-00 FERRITE BEAD 3.5X1X4.5 1
666-13511-00 FERRITE BEAD 3.5X1X4.5 1
706-BA201-01 HEAT SINK 1
706-BA201-01 HEAT SINK 1
706-V2501-01 HEAT SINK 1
852-93008-81 COMPOSE SCREW SJ2836 M3X8-D.Zn 5
998 JUMPER WIRE 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-50392-00 ZENER DIODE BZV55-B3V9 1
340-51602-00 SMD ZENER BZV55-B16V 1
340-52702-00 ZENER DIODE BZV55-B27V 1
342-29070-80 SMD TRANSISTOR MMBT2907ALT1 1
342-39040-00 SMD TRANSISTOR MMBT3904 1
342-39040-00 SMD TRANSISTOR MMBT3904 1
342-39060-30 SMD TRANSISTOR MMBT3906LT1 1
353-04310-30 SMD IC LM431ACDR 1
353-27010-10 SMD IC PS2701-1-V 1
353-27010-10 SMD IC PS2701-1-V 1
353-48000-10 SMD IC ML4800CS 1
455-22010-H0 SMD RESISTOR RC11-1/8W-10-J 1
Version: 1.0
-71 -
455-22210-H0 SMD RESISTOR RC11-1/8W-1K-J 1
455-22218-H0 SMD RESISTOR RC11-1/8W-1.8K-J 1
455-22326-F1 SMD RESISTOR RC-05K2672FT 1
455-22326-F1 SMD RESISTOR RC-05K2672FT 1
455-31000-H0 SMD RESISTOR RC06J000 1
Version: 1.0
-72 -
456-2510R-C2 SMD CAPACITOR 08052E105Z250BA 1
456-3133H-12 SMD CAPACITOR C2012CH1H331JT 1
456-3233K-B2 SMD CAPACITOR C2012X7R1H332KT 1
467-1C033-H03 CARBON RESISTOR 1/6W-33Ω-J 1
467-1C210-H03 CARBON RESISTOR 1/6W-1K-J 1
467-1D122-H03 CARBON RESISTOR RT14-1/4W-220Ω-J 1
782-L27W18-200C POWER PCB 1
895-6020025-50 RIVET GB876-86-2X2.5- 1
895-6020025-50 RIVET GB876-86-2X2.5- 1
Version: 1.0
-73 -
998 JUMPER WIRE 1
998 JUMPER WIRE 1
998 JUMPER WIRE 1
998 JUMPER WIRE 1
998 JUMPER WIRE 1
998 JUMPER WIRE 1
998 JUMPER WIRE 1
360-10001-00 TACT SWITCH KFC-A06-4X4.5X5B 1
364-33101-00 3-PINS CONNECTORS TJC3-03A 1
467-1C243-H03 CARBON RESISTOR 1/6W-4.3K-J 1
467-1C243-H03 CARBON RESISTOR 1/6W-4.3K-J 1
782-L27W18-050A BUTTON PCB 1
870-30184-020 KEY BRACKET ( BLACK ） 1
877-50490-0T0 KEY (PLATE SILVERY WHITE ） 1
343-18150-104 TRANSISTOR 2SC1815-Y 1
352-51170-00 IC HRM538BB5117 (D) 1
364-33104-00 3-PINS CONNECTORS TJC3-03AWT 1
459-1410M-00 CERAMIC CAPACITOR DD410-SR104M25 1
464-6D622-M0 ELECTROLYTIC CAP CD110-16V-22uF-M 1
Version: 1.0
-74 -
782-L27W18-0900 IR RECEIVE PCB 1
340-10132-20 LIGHT-EMITTING DIODE HFT5038CPBR 2
655-3K301-02 (3-PINS) LEAD WITH HOUSING 1
329-61805-00 CRYSTAL HC-49U 18.432MHZ 1
340-00003-00 DIODE IN4001 1
352-78090-90 IC TA78L09 (D) 1
364-11212-00 EARPHONE JACK ST-112 1
364-3A205-00 21 CONNECTORS HJ-2105W 1
364-3B101-00 十 2-PINS CONNECTORS TJC3-12A 1
364-3D101-00 十-PINS CONNECTORS TJC3-10A 1
364-41205-00 ANT SOCKET HR-J2 1
462-90410-H0 POLYESTER CAP 63V-0.1uF-J 1
464-6E610-M0 ELECTROLYTIC CAP CD110-25V-10uF-M 1
464-6F747-M1 ELECTROLYTIC CAP CD110-35V-470uF-M 1
467-1D010-H0 CARBON RESISTOR RT14-1/4W-10Ω-J 1
471-1056H-00 PEAKING COIL EL0606SKI-560J 1
471-1110K-00 PEAKING COIL EL0606SKI-101K 1
471-1110K-00 PEAKING COIL EL0606SKI-101K 1
471-2056H-60 PEAKING COIL LGA0307-56uH-J 1
471-2068K-103 PEAKING COIL LGA0410-68uH-K 1
471-2068K-103 PEAKING COIL LGA0410-68uH-K 1
Version: 1.0
-75 -
477-40031-00 FIXED COIL LG750 1
477-40230-00 FIXED COIL LH470-1 1
590-40511-00 TUNER JS-6B2/121A2 1
590-40512-00 *TUNER JS-6B2/122A2-A2 1
615-10511-00B TV BOARD SHUTTER ASS'Y (TOP ） 1
615-10512-00A TV BOARD SHUTTER ASS'Y (BOTTOM ） 1
665-N0120-00 COAXIAL CABLE CSYV-2B-120 1
665-N0260-00 *COAXIAL CABLE CSYV-2B-260 1
666-12301-00 FERRITE BEAD TY23X13.5X6 1
666-13501-0G FERRITE BEAD 3.5X1X6 1
852-53006-81 SCREW SJ2830 M3X6-D.Zn 2
859-1A1373-00 TVINTERFACE SPACE PLATE ) 1
870-10290-00 RF BRACKET 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
340-00001-0S SMD DIODE LL4148 1
342-08470-90 SMD TRANSISTOR BC847AW 1
342-08570-90 SMD TRANSISTOR BC857 AW 1
353-05050-20 SMD IC PESD5V0L5UY 1
353-05050-20 SMD IC PESD5V0L5UY 1
353-11090-20 SMD ICNJW1109M 1
353-30080-10 SMD ICTPA3008D2 1
353-34100-80 *SMD IC MSP3410G PQFP80(M) 1
455-12000-H0 SMD RESISTOR FTR0603000XR 1
Version: 1.0
-76 -
455-12075-H0 SMD RESISTOR FTR0603750JR 1
Version: 1.0
-77 -
456-1447R-C3 SMD CAPACITOR C3216Y5V1C474ZT 1
456-1447R-C3 SMD CAPACITOR C3216Y5V1C474ZT 1
456-2215K-B1 SMD CAPACITOR 06032R152K250BA 1
456-2410M-C1 SMD CAPACITOR 06032E104M250BA 1
Version: 1.0
-78 -
Version: 1.0
-79 -
456-3018H-11 SMD CAPACITOR 0603CG180J500BA 1
464-6C722-M02 ELECTROLYTIC CAP CD110-10V-220uF-M 1
Version: 1.0
-80 -
464-6E610-M02 *ELECTROLYTIC CAP CD110-25V-10uF-M 1
464-60510-M02 ELECTROLYTIC CAP CD110-50V-1uF-M 1
464-60510-M02 ELECTROLYTIC CAP CD110-50V-1uF-M 1
464-60533-M02 ELECTROLYTIC CAP CD110-50V-3.3uF-M 1
477-40211-00 SMD FIXED COILSLF12575T-330M3R2 1
477-90003-00 SMD CERAMIC FILTER LFA20-2A1E103M 1.5
477-90004-00 SMD CERAMIC FILTER LFA20-2A1E104M 1
666-13207-00 SMD FERRITE BEAD STPB3216-380PT 1
Version: 1.0
-81 -
782-L27W18-150A SOUND TRANSER BOARD PCB 1
364-49219-00 SOCKET HJ-2105F 1
364-91202-00 S-VIDEO TERMINAL CKX5-2K-2 1
364-93219-00 AV JACK AV3-14WKD 1
353-05050-20 SMD IC PESD5V0L5UY 1
353-05050-20 SMD IC PESD5V0L5UY 1
353-05050-20 SMD IC PESD5V0L5UY 1
456-2410R-C1 SMD CAPACITOR C1608Y5V1E104ZT 1
Version: 1.0
-82 -
782-L27W18-4000 VIDEO PROCESSING PCB 1
329-61003-00 CRYSTAL HC-49/US 10.000MHZ 1
329-61402-00 CRYSTAL HC-49/US 14.31818MHZ 1
329-61402-00 CRYSTAL HC-49/US 14.31818MHZ 1
329-62806-00 CRYSTAL HC-49uS 28.322MHz 1
340-50360-00 ZENER DIODE HZ4A2 1
340-50470-00 ZENER DIODE HZ5B1 1
364-3B101-00 十 2-PINS CONNECTORS TJC3-12A 1
364-3D101-00 十-PINS CONNECTORS TJC3-10A 1
364-91204-00 VGA SOCKET 1
364-95209-00 AV JACK AV13-05-501 1
462-B0433-H0 POLYESTER CAP CL21X-50V-0.33uF-J 1
Version: 1.0
-83 -
615-10509-00A DIGITAL BOARD SHUTTER ASS'Y (TOP ） 1
615-10510-00A DIGITAL BOARD SHUTTER ASS'Y (BOTTOM ） 1
655-B1202-52 (12-PINS) LEAD WITH HOUSING 1
655-T1202-50 （10-PINS） LEAD WITH HOUSING 1
804-20427-00 DIGITAL INTERFACE SPACE PLATE 1
340-00289-00 SMD DIODE BAV99LT1 1
340-00289-00 SMD DIODE BAV99LT1 1
340-00289-00 SMD DIODE BAV99LT1 1
340-00296-00 SMD DIODE SK34 1
340-00296-00 SMD DIODE SK34 1
340-00296-00 SMD DIODE SK34 1
340-00362-00 SMD DIODE MBRST130LT3 1
340-00372-00 SMD DIODE MMBD1204 1
340-50512-00 SMD ZENER DIODE BZV55-B5V1 1
340-50512-00 SMD ZENER DIODE BZV55-B5V1 1
342-01380-00 *SMD TRANSISTOR BSS138LT1 1
342-08570-40 SMD TRANSISTOR BC857B 1
342-08570-40 SMD TRANSISTOR BC857B 1
353-DPTV0-20 SMD IC DPTV-SVP-EX52 1
353-03580-80 SMD IC LM358D (M) 1
353-05040-20 SMD IC PESD5V0L4UG 1
353-05050-20 SMD IC PESD5V0L5UY 1
353-11170-G0 SMD IC AMS1117-1.8 (D) 1
353-11170-G0 SMD IC AMS1117-1.8 (D) 1
353-11170-G0 SMD IC AMS1117-1.8 (D) 1
353-11170-G0 SMD IC AMS1117-1.8 (D) 1
Version: 1.0
-84 -
353-11170-10 SMD IC B1117N-2.5 (D) 1
353-11170-10 SMD IC B1117N-2.5 (D) 1
353-11170-20 SMD IC AS1117M-3.3 (M) 1
353-11170-20 SMD IC AS1117M-3.3 (M) 1
353-11170-20 SMD IC AS1117M-3.3 (M) 1
353-11170-20 SMD IC AS1117M-3.3 (M) 1
353-12130-10 SMD ICCM1213-08MS 1
353-15010-50 SMD ICAP1501-50K5 1
353-15010-50 SMD ICAP1501-50K5 1
353-24020-60 SMD IC 24C02N-10SI27 1
353-24210-50 SMD IC 24LC21A/SN 1
353-24320-50 SMD IC24LC32A/SN 1
353-26323-10 SMD IC K4D2632838F-QC50 1
353-28300-00 SMD ICAS2830AT-3.3 (D) 1
353-29040-30 SMD IC W29C040P-90B 1
353-30620-20 SMD ICM30620SPGP (D) 1
353-32570-10 SMD ICSN74CBT3257CDR 1
353-32570-10 SMD ICSN74CBT3257CDR 1
353-40520-80 SMD IC HEF4052BT (M) 1
353-43440-10 *SMD ICCS4344CZZ 1
353-51470-10 SMD ICTVP5147PFP 1
353-70020-10 SMD IC NDC7002N 1
353-70020-10 SMD IC NDC7002N 1
353-74140-40 SMD ICSN74LVC14AD 1
353-90110-10 SMD ICSiI9011CLU 1
364-T1904-00 SMD 19-PINSHDMI 1775245-2 1
364-T3001-00 SMD 30-PINSFF-A1255-WRS 1
454-03710-MB SMD ELECTROLYTIC CAP CDPS-10V-100uF-M 1
454-04610-MA SMD ELECTROLYTIC CAP CDPS-16V-10uF-M 1
Version: 1.0
-85 -
Version: 1.0
-86 -
454-04710-MC SMD ELECTROLYTIC CAP CDPS-16V-100uF-M 1
454-06547-MA SMD ELECTROLYTIC CAP CDPS-25V-4.7uF-M 1
Version: 1.0
-87 -
455-10015-H9 SMD RESISTOR NCA4R150JR 1
Version: 1.0
-88 -
Version: 1.0
-89 -
Version: 1.0
-90 -
Version: 1.0
-91 -
Version: 1.0
-92 -
Version: 1.0
-93 -
Version: 1.0
-94 -
Version: 1.0
-95 -
Version: 1.0
-96 -
Version: 1.0
-97 -
Version: 1.0
-98 -
Version: 1.0
-99 -
474-14A22-K0 SMD COIL SGMI3216M2R2KT 1
Version: 1.0
-100
-
666-12010-00 SMD FERRITE BEAD GB2012D151T 1
666-13204-00 SMD FERRITE BEAD STBL3216-190PT 1
782-L27W18-6900 DSP BOARD PCB 1
Version: 1.0

Akira LCT 27pbstp

Uploaded by

Copyright:

Available Formats

Akira LCT 27pbstp

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Akira LCT 27pbstp

Uploaded by

Copyright:

Available Formats

LCD TV

Model No.: LCT-27PBSTP.doc

SAFETY PRECAUTION .............................................................................................................4

APPEARANCE & CONTROL FUNCTION ...............................................................................11

ALIGNMENT INSTRUCTION ...................................................................................................16

WORKING PRINCIPAL ANALYSIS ..........................................................................................29

IC BLOCK DIAGRAM ...............................................................................................................31

ASSEMBLY LIST ......................................................................................................................35

TROUBLE SHOOTING GUIDE ................................................................................................41

Model No.: LCT-27PBSTP.doc

IMPORTANT SAFETY PRECAUTION

Model No.: LCT-27PBSTP.doc

Model No.: LCT-27PBSTP.doc

Screen Size & Type 597 x 336 mm

Net Dimension 700 x 230 x 582 mm

Gross Dimension 800 x 309 x 670 mm

Net Weight 19kg

Gross Weight 21kg

Power Consumption (Normal Operation) 140 Watts (MAX)

Power Consumption (Standby

Front Cabinet Colour Silver + Black

Back Cabinet Colour Grey 05

Stand Type / Colour Swivel / black+ silver

Power Adapter Input Voltage

Power Adapter Output Voltage

Power Adapter Output Voltage No adaptor

Power Plug Type

Mains Voltage 100-240V

Mains Frequency 50/60Hz

Power Plug Type 2.5-Amp round pin(VDE standard)

Operating Temperature 0 - 40 deg C

Storage Temperature -25 - -55degC

90% RH Max(Ta<=40 deg C& web-bulb

Relative Humidity Level temperature should be 39degC Max (Ta>40degC)

RF PAL I , B/G , D/K

RF SECAM B/G , D/K , L/L'

VIDEO PAL Yes

VIDEO SECAM Yes

VIDEO NTSC NTSC PLAYBACK 3.58 / 4.43

Model No.: LCT-27PBSTP.doc

Brand & Model CMO , V270W1-L04

Resolution 1280 x 720

Displayable Colour 16.7M

Hard coating(2H),Anti-reflective coating<less 2%

Viewing Angle (H/V) 170/170

Display Response Time 16.6ms

Contrast Ratio 900 : 1

Lamp Life >=50,000

Bad pixels warranty (Bright / Dark /

Channel Coverage 40 - 870Mhz

Preset Channels 1 - 200

S + Hyper Band CATV Yes

Aerial Input N/A

Comb Filter Yes 3D

Velocity Modulation N/A

Noise Reduction Weak / Medium / Strong

Film Theater N/A

Detail Enhancer Yes