TSS-800 Infinity Subwoofer PDF
TSS-800 Infinity Subwoofer PDF
TSS-800 Infinity Subwoofer PDF
(TSS-800 SYSTEM)
SERVICE MANUAL
CONTENTS
TSS-Sub800 Specifications
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications
and construction details in this and related Infinity publications are therefore subject to change without notice.
1
TSS-Sub800
PACKAGING
2
TSS-Sub800
TSS-Sub800 100W Powered Sub/ Plate Amp
Input Sensitivity
Input Frequency 50 Hz 50 Nominal Freq.
Line Input (L&R) 15.62 mVrms ±2dB To 1 Watt Single input driven, AP Zo=600 Ohms
LFE Input 10.36 mVrms ±2dB To 1 Watt LFE input driven only, AP Zo=600 Ohms
Signal to Noise
SNR-A-Weighted 100 dBA 85 rel. to rated power A-Weighting filter
SNR-unweighted 80 dBr 80 rel. to rated power 22K filter
SNR @ 1W-unweighted 60 dBr 60 rel. to 1W Output 22K filter
Volume @max, using RMS reading
Residual Noise Floor 1.5 mVrms 2.5 DMM/VOM (or A/P)
Volume @max, w/ A/P Swept Bandpass
Residual Noise Floor 1 mVrms(max) 2 Measurement (Line freq.+ harmonics)
Input Impedance
Line input L&R , LFE >10 K ohms n/a Nominal
Filters
2nd order variable 50-150Hz + 2nd order
Low Pass (fixed or variable) 4th order -- ±2dB fix
Slope & Q dB/Octave n/a
Subsonic filter (HPF) 2nd order fix Hz ±2dB
Slope & Q dB/Octave n/a
Features
LFE Input YES Functional
Phase Switch (yes/no) YES -- Functional
Volume pot Taper (lin/log) LOG -- Functional
ATO YES Functional
Input Configuration
Line In (L,R) L ,R -- Functional RCA inputs (L&R)
Line level in LFE LFE Functional RCA single input
Transients/Pops
ATO Transient 5 mV-peak 10 @ Speaker Outputs
Turn-on Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from OFF to ON
Turn-off Transient 50 mV-peak 100 @ Speaker Outputs AC Line cycled from ON to OFF
Efficiency
Maximum allowable input power under
nominal Input voltage and frequency, HOT
Stand-by Input Power 14 Watts 18 @ nom. line voltage or COLD operation.
Power Cons.@rated power 195 Watts 210 @ nom. line voltage 100 Watts @ 4 Ohms
3
TSS-Sub800
Protection
Short Circuit Protection YES -- Functional Direct short at output
Temperature rise should not exceed 35K
Thermal Protection 65 deg. C -- Functional @1/8 max unclipped Power rise
DC Offset Protection YES -- Functional DC present at Speaker Out leads Relay or crowbar (for driver/fire protection)
4
TSS-800 (120V) OM 2/24/06 10:01 AM Page 10
TSS-Sub800
SUBWOOFER CONTROLS
Rear Panel 1 Subwoofer-Level Control
2 Crossover-Frequency Adjustment
3 Phase Switch
¡ 4 LFE Input
5 Line-Level Inputs
™
6 Power Indicator LED
£ 7 Power Switch
¢ ∞
A Few Suggestions
§ We recommend that you do not operate your speakers or
subwoofer with the bass, treble and loudness controls set to
full boost.This will place undue strain on your electronics and
speakers and could damage them.
TSS-Sub800 ¶
NRTU/C
CSA22-2 NO.1
UL 1492
The volume control setting on your processor/preamp or receiver
is not a specific indication of the overall loudness level of the
speakers.The only important consideration is the loudness level at
which the system can be played, regardless of where the volume
control is set.
Important!
Whenever changing cables, pulling plugs, etc., ALWAYS TURN OFF
ALL EQUIPMENT, including the subwoofer.
5
TSS-800 (120V) OM 2/24/06 10:01 AM Page 11
TSS-Sub800
SUBWOOFER CONNECTIONS
If you have a Dolby® Digital or DTS® receiver/ If your receiver/processor does not contain
processor with a low-frequency-effects (LFE) a Dolby Digital or DTS processor but has a
or subwoofer output: subwoofer output:
RECEIVER/PROCESSOR
SUBWOOFER OR
LFE OUTPUT
15' (4.5m)
subwoofer
cable
included 15' (4.5m)
subwoofer cable
included
TSS-Sub800/230 TSS-Sub800/230
6
TSS-800 (120V) OM 2/24/06 10:01 AM Page 12
TSS-Sub800
OPERATION
Surround Modes Crossover Adjustment
When using the TSS-800 in a Dolby Digital or DTS home theater The Crossover Frequency Control 2 determines the highest
system, make sure all speakers are set to “Small”. In a Dolby frequency at which the subwoofer reproduces sounds. For the
Pro Logic® home theater system, make sure the receiver’s TSS-800, it is recommended that this control be set at 120Hz
center channel mode is set to “Normal.” (approximately the 3 o’clock position).
Some Dolby Digital-equipped receivers/processors offer different NOTE: This control will have no effect if the LFE Input 4 is
setup options for each source or surround mode (e.g., CD-stereo, used. If you have a Dolby Digital or DTS receiver/processor,
videotape, Dolby, Pro Logic). In each case, follow your equipment’s the low-pass frequency is set by the receiver/processor. Consult
instructions to ensure that the subwoofer output is turned on and your owner’s manual to learn how to view or change this setting.
that the speakers are set to “Small” in each mode. A setting of 120Hz – 150Hz is recommended.
7
TSS-Sub800
8
TSS-Sub800
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
Sweep Function
Driver Function
9
TSS-Sub800
10
TSS-Sub800
11
TSS-Sub800
TSS-Sub800 AMP
yes
yes yes Check ,+VCC& -VCC
Test R121,R122 signal no DC voltage Check J123,J124 etc
no
yes yes
Check Q107,Q108,Q105,
Check RY101,D102,Q113,Q114 etc
Q106,Q103,Q104,U101,etc
yes
no
Check U101,Q115,Q116,R138 etc Set R138 to R140’S
yes Voltage is 0.51VDC
yes
Check P102 signal The Amp ass’Y OK, END
12
TSS-Sub800
13
TSS-Sub800
14
TSS-Sub800
15
TSS-Sub800
16
TSS-Sub800
17
TSS-Sub800
18
TSS-Sub800
TSS-Sub800 (120v) Electrical Parts List
Part Number Description Qty Reference Designator
PREAMP PCB
Resistors
Capacitors
Semiconductors
19
TSS-Sub800
Part Number Description Qty Reference Designator
PREAMP PCB
Miscellaneous
LIMITER PCB
Resistors
Capacitors
Semiconductors
Miscellaneous
POWER/MAIN PCB
Resistors
20
TSS-Sub800
Part Number Description Qty Reference Designator
POWER/MAIN PCB
Capacitors
Semiconductors
Miscellaneous
21
TSS-Sub800
Part Number Description Qty Reference Designator
POWER/MAIN PCB
MISCELLANEOUS/MECHANICAL
22
TSS-Sub800
23
TSS-Sub800
1 2 3 4 5 6
FM phase sw
P1 1 4
2 5 C252 C251 C244 C243 C246 +15V
1 0.1uF/C 10uF 0.1uF/C 10uF 0.1uF/C
3 6
2
8
D SW301A SW301B +15v D
FM phase sw C218 U201D
U201C 0.27uF/MSC TL074 U203
C208 U201A 13
C216 TL074 4558 -15v
220P 3 TL074 9 14 U201 U202
5
0.22uF/MSC R226 R227 -15V
4
1 8 3 1 6 4 12 TL074 TL074
11
11
C206
JK202A R213 R216 2 1 2 R224 10
6.8K VR202A 6.8K VR202B C217
2 10K R212 6.8K B20K B20K R228
1K 10uF R211 5.1K 0.082uF/MSC
G2 C211 10k R223 C215 R225 10K C254 C253 C242 C241 C245
220P 6.8K
1 0.1uF/MSC 10K 0.1uF/C 10uF 0.1uF/C 10uF 0.1uF/C
2
1
D201 D202 C207 220P
1 R214 2 R217 4148 4148
1
1K 10K
C210 -15V +15v
220P
1
R4
3
C5 R1 R5 1.47K
1 2
1
2
5.1k R231 100K R234 C4 TL074
U202B R3 8.25K 9 14
C219 2.87K 6 TL074 8 R238 12
C220 C1 C2
2
220P C3
2 C221 C222 7 0.047uF/MSC 10 22uF
C R237 22K C
1 5 R2 240 15.4K R240
10uF 3 JUP JUP JUP Q201
2
U202A .47uF/MSC .47uF/MSC OPT 10K
1
R230 R7 R6
TL074 3
1
1
OPT OPT
2
+15V
C213
10uF R257
Q207
2
C231 D213 2M R260
R253 C1815
1 2 4.7K
3 M201
150 3.3V SGO
10uF 7
PTC
1
C230 220P D216 6
U203B +15V
1
JUP 5
+15V 6 4558D
2
R221 10K 4
7 -15V
R251 3
D212 +15v R252 2 R258 1 5 MUTE
1
D206 R250 D215 2
C214 220P GND
2
2
2
2
D117 C229 47P R259
JK202B P2.5-7
1
2
C1815 100K R262 1M
1K 7 1 R249 2 2 D214
1.2K
D207 D211 R254 100uF 18K
5 1 1 2 3
G3
C212
1
2
1
47K R222 4148 1K
TL074
1
2
4148 R255
2
PAGE: 1/3
DSGN
APVD
CUSTOMER: JBL DATE:2006-6-10
1 2 3 4 5 6
24
TSS-Sub800
25
TSS-Sub800
26