Refrigeration and Air-Conditioning

Visit : www.Civildatas.
com
Refrigeration and Air-conditioning

1. Heat Pump and Refrigeration cycles and systems
Heat Engine, Heat Pump
Reversed Carnot Cycle
Liquefaction of Gases
m
Production of Solid Ice
Refrigeration capacity (Ton of refrigeration)
co
2. Vapour Compression System
Modifications in Reversed Carnot Cycle with Vapour as a Refrigerant
Vapour Compression Cycle
Actual Vapour Compression Cycle
Heat Pump
.
Second Law Efficiency of Vapour Compression Cycle
3. Refrigerants
Designation of Refrigerants
tas
Secondary Refrigerants
Substitutes for CFC Refrigerants
lda
Azeotropic Mixtures
4. Refrigerant Compressors
Highlight
Types of Compressors
vi
Volumetric Efficiency of reciprocating Compressors

Effect of Clearance on Work
Performance Characteristics of Reciprocating Compressors
Rotary Compressors
Screw Compressors
Ci
Centrifugal Compressors
Performance Characteristics of Centrifugal Compressors
Comparison of Performance of Reciprocating and Centrifugal
Axial flow compressor
w.
Flash Chamber
5. Condensers
Heat Rejection Ratio
ww
Types of Condensers
6. Expansion Devices
Types of Expansion Devices
Automatic or Constant-Pressure Expansion Valve
Thermostatic-Expansion Valve
Capillary Tube and Its Sizing
Visit : www.Civildatas.com
7. Evaporators
8. Gas Cycle Refrigeration
Limitations of Carnot Cycle with Gas as a Refrigerant
Reversed Brayton or Joule or Bell Coleman Cycle
Application to Aircraft Refrigeration
The Joule- Thomson Coefficient and Inversion Curve
Reversed Stirling Cycle
m
9. Vapour-Absorption System
Simple Vapour-Absorption System
Maximum Coefficient of Performance of a Heat Operated Refrigerating Machine
co
Representation of Vapour Absorption Cycle on In Practical Single-Effect Water-Lithium
Double-effect H20 - LiBr2 Absorption System
Electrolux Refrigerator
.
10. Ejector-Compression System tas
Water as a Refrigerant
Steam Ejector System
11. Psychrometry
Psychometric Properties
lda
Specific humidity or Humidity ratio
Relative humidity
Dew point temperature
Degree of saturation
Wet Bulb Temperature (WBT)
Adiabatic saturation of air and adiabatic saturation temperature
vi
Psychometric Chart
Basic Processes in Conditioning of Air
Sensible heating
Sensible cooling
Ci
Humidification
Dehumidification
Heating and humidification
Cooling and dehumidification
Cooling and humidification
w.
Heating and dehumidification

Sensible heat factor (SHF)
Psychometric Processes in Air Conditioning Equipment
Bypass factor
Heating coil
ww
Air Washer
Water Injector
Steam Injector
Summer Air Conditioning-apparatus Dew Point(RSHF, GSHF, TSH, GTH, Minimum quantity of air (cmm)min)
Air refrigeration system

Boot-strap
Simple evaporative
Regenerative
Boot-strap evaporative
Comfort
Effective temperature
Load calculation
m
Solar refrigeration
Duct Design
. co
tas
vi lda
Ci
w.
ww
1.
Heat Pump and Refrigeration cycles and systems
m
Objective Questions (IES, IAS, GATE)
co
Heat Engine, Heat Pump
1. A heat pump works on a reversed Carnot cycle. The temperature in the condenser
coils is 270 C and that in the evaporator coils is -230 C. For a work input of 1 kW, how
much is the heat pumped?
.
(a) 1 kW (b) 5 kW [IES 2007]
(c) 6 kW
1. Ans. (c) For heat pump (COP)H.P =
tas Q1
W
=
T1
T1 − T2
=
(d) None of the above
300
300 − 250
or Q1=6xW = 6 kW
2. A heat pump is used to heat a house in the winter and then reversed to cool the
lda
house in the summer. The inside temperature of the house is to be maintained at 20oC.
The heat transfer through the house walls is 7·9 kJ/s and the outside temperature in
winter is 5oC. What is the minimum power (approximate) required driving the heat
pump? [IES-2006]
(a) 40·5 W (b) 405 W (c) 42·5 W (d) 425 W
Q1 T1 293 7.9 ×15
2. Ans. (b) ( COP ) HP =
vi
= = orW = kW = 405W
W T1 − T2 15 293
4. A refrigerator based on reversed Carnot cycle works between two such temperatures
that the ratio between the low and high temperature is 0.8. If a heat pump is operated
Ci
between same temperature range, then what would be its COP? [IES-2005]
(a) 2 (b) 3 (c) 4 (d) 5
T2 T1
4. Ans. (d) = 0.8 or ( COP )H.P = =5
T1 T1 − T2
w.
5. A heat pump for domestic heating operates between a cold system at 00C and the hot
system at 60oC. What is the minimum electric power consumption if the heat rejected is
80000 kJ/hr? [IES-2003]
(a) 2 kW (b) 3 kW (c) 4 kW (d) 5 kW
ww
5. Ans. (c)
For minimum power consumption,
Q1 Q2 Q1 − Q2 W
= = =
T1 T2 T1 − T2 T1 − T2
Q1 Q2 Q1 − Q2 W
= = =
T1 T2 T1 − T2 T1 − T2
T1 − T2 80000 333 − 273
W = Q1 × = × = 4kW
m
T1 3600 333
co
6. A refrigerator working on a reversed Carnot cycle has a C.O.P. of 4. If it works as a
heat pump and consumes 1 kW, the heating effect will be [IES-2003]
(a) 1KW (b) 4 KW (c) 5 KW (d) 6 KW
6. Ans. (c)
.
(COP) Heat pump = (COP) refrigerator + 1 = 4 + 1 = 5
tas
or (COP) Heat pump =
Q1 Heating effect
W
=
work input
or Heating effect, Q1 = W x (COP)Heat pump = 5 kW
lda
12. The coefficient of performance (COP) of a refrigerator working as a heat pump is
given by [IES-1992, 1994, 2000; GATE-1995]
(a) (COP)heat pump = (COP)refrigerator+ 2 (b) (COP)heat pump = (COP)refrigerator+ 1
(c) (COP)heat pump = (COP)refrigerator - 1 (d) (COP)heat pump = (COP)refrigerator
12. Ans. (b) The COP of refrigerator is one less than COP of heat pump, if same
refrigerator starts working as heat pump i.e. (COP)heat pump = (COP)refrigerator + 1
vi
9. A heat pump operating on Carnot cycle pumps heat from a reservoir at 300 K to a
Ci
reservoir at 600 K. The coefficient of performance is [IES-1999]

(a) 1.5 (b) 0.5 (c) 2 (d) 1
T1 600
9. Ans. (c) COP of heat pump = = =2
T1 − T2 600 − 300
w.
10. Assertion (A): Heat pump used for heating is a definite advancement over the simple
electric heater. [IES-1995]
Reason (R): The heat pump is far more economical in operation than electric heater.
10. Ans. (b) A and R are right. R is not correct explanation for A.
ww
11. A heat pump is shown schematically as [IES-1994]
m
. co
tas
11. Ans. (c) In heat pump, heat is rejected to source, work done on compressor, and
heat absorbed from sink.
lda
13. A heat pump working on a reversed Carnot cycle has a C.O.P. of 5. lf it works as a
refrigerator taking 1 kW of work input, the refrigerating effect will be [IES-1993]
(a) 1 kW (b) 2 kW (c) 2 kW (d) 4 kW
13. Ans. (d)
work done
COP heat pump = or heat rejected = 5 x work done
heat rejected
vi
And heat rejected = refrigeration effect + work input

or 5 x work input - work input = refrigeration effect
or 4 x work input = refrigeration effect
Ci
or refrigeration effect = 4 x 1kW = 4kW
15. A building in a cold climate is to be heated by a Carnot heat pump. The minimum
outside temperature is -23°C. If the building is to be kept at 27oC and heat requirement
is at the rate of 30 kW, what is the minimum power required for heat pump? [IAS-2007]
w.
(a) 180 kW (b) 30 kW (c) 6 kW (d) 5 kW

Q1 T1 ⎛ T ⎞ ⎛ 250 ⎞
15. Ans. (d) (COP)H.P= = orW = Q1 ⎜1 − 2 ⎟ = 30 × ⎜1 − ⎟ = 5KW
W T1 − T2 ⎝ T1 ⎠ ⎝ 300 ⎠
ww
16. In the system given above, the temperature T =

300 K. When is the thermodynamic efficiency ɳE of
engine E equal to the reciprocal of the COP of R?
(a) When R acts as a heat pump
(b) When R acts as a refrigerator
(c) When R acts both as a heat pump and a
refrigerator
(d) When R acts as neither a heat pump nor a
refrigerator
m
. co
tas
lda
[IAS-2007]
16. Ans. (a)
300 1 1
ηE = 1 − = = or COP = z
600 2 COP
300 150
(COP) H .P = = z and (COP) R = =1
vi
300 − 150 300 − 150

∴R must act as a Heat pump
Ci
17. Assertion (A): The coefficient of performance of a heat pump is greater than that for
the refrigerating machine operating between the same temperature limits.
Reason (R): The refrigerating machine requires more energy for working where as a
heat pump requires less. [IAS-2002; IES - 2002]
17. Ans. (c) R is false. For refrigerating machine our aim is to extract heat from lower
w.
temperature source. In heat pump we are interested on heat addition to higher

temperature side so it is heat extracted + work added. That so why it’s COP is higher but
work requirement is same for both the machine.
ww
18. In a certain ideal refrigeration cycle, the COP of heat pump is 5. The cycle under
identical condition running as heat engine will have efficiency as [IAS-2001]
(a) zero (b) 0.20 (c) 1.00 (d) 6.00
T1 T1 − T2 1 1
18. Ans. (b) (COP ) HE = and η = = = = 0.2
T1 − T2 T1 ( COP ) HE 5
19. The COP of a Carnot heat pump used for heating a room at 20° C by exchanging
heat with river water at 10° C is [IAS-1996]
(a) 0.5 (b) 2.0 (c) 28.3 (d) 29.3

T1 293
19. Ans. (d) COP = = = 29.3
T1 − T2 293 − 283
20. Assertion (A): Although a heat pump is a refrigerating system, the coefficient of
performance differs when it is operating on the heating cycle.
Reason(R): It is condenser heat that is useful (the desired effect) instead of the
refrigerating effect.
m
20. Ans. (a)
21. An industrial heat pump operates between the temperatures of 27°C and -13°C. The
rates of heat addition and heat rejection are 750 Wand 1000 W, respectively. The COP
co
for the heat pump is [GATE-2003]
(a) 7.5 (b) 6.5 (c) 4.0 (d) 3.0
21. Ans. (c)
Q1 1000
( COP )HP = = =4
.
Q1 − Q2 1000 − 750
tas
lda
23. Any thermodynamic cycle operating between two temperature limits is reversible if
vi
the product of efficiency when operating as a heat engine and the coefficient of
performance when operating as refrigeration is equal to 1. [GATE-1994]
23. Ans. False
Ci
w.
ww
26. In a reversible cycle, the source temperature is 2270C and the sink temperature is
270C. The maximum available work for a heat input of 100 kJ will be
(a) 100 kJ (b) 60 kJ (c) 40 kJ (d) 88 kJ [IAS-1995]
26. Ans. (c)
m
co
Reversed Carnot Cycle
27. A refrigerator works on reversed Carnot cycle producing a temperature of -40°C.
Work done per TR is 700 kJ per ten minutes. What is the value of its COP?
.
(a) 3 (b) 4.5 (c) 5.8 (d) 7.0 [IES-2005]
27. Ans. (a) W =
700
10
tas
kJ / min,Q = 210kJ / min, COP =
210
70
=3
28. The coefficient of performance of a refrigerator working on a reversed Carnot cycle is

4. The ratio of the highest absolute temperature to the lowest absolute temperature is
(a) 1.2 (b) 1.25 (c) 3.33 (d) 4 [IES-1999; IAS - 2003]
28. Ans. (b)
lda
T2 1 T T
( COP )Refrigerator of reversed Carnot cycle = =
T1
= 4, or 1 -1 = 0.25 or 1 = 1.25
T1 -T2 -1 T2 T2
T2
30. In an ideal refrigeration (reversed Carnot) cycle, the condenser and evaporator
temperatures are 27°C and -13°C respectively. The COP of this cycle would be
vi
(a) 6.5 (b) 7.5 (c) 10.5 (d) 15.0 [IES-1997]
30. Ans.(a ) COP =

T1
=
( 273 − 13) = 6.5
T2 − T1 ( 273 + 27 ) − ( 273 − 13)
Ci
31. A refrigeration system operates on the reversed Carnot cycle. The temperature for
the system is: Higher temperature = 40°C Lower temperature = 20°C
The capacity of the refrigeration system is 10 TR. What is the heat rejected from the
w.
system per hour if all the losses are neglected? [IAS-2007]

(a) 1·25 kJ/hr (b) 1·55 kJ/hr (c) 2·3 kJ/hr (d) None of the above
T2 293 293 Q2
31. Ans. (d) COP= = = =
T1 − T2 213 − 293 20 W
ww
20
Q2 = 10 × 14000 KJ / hr or W = 14 × 104 × KJ / hr
293
20 ⎛ 20 ⎞
Q1 = Q2 + W = 14 × 104 + 14 × 104 × = 14 × 104 ⎜1 + ⎟ KJ / hr = 150MJ / hr
293 ⎝ 293 ⎠
32. A refrigerating machine working on reversed Carnot cycle takes out 2 kW of heat
from the system at 200 K while working between temperature limits of 300 K and 200 K.
C.O.P. and power consumed by the cycle will, respectively, be [IES-1997; IAS-2004]
(a) 1 and 1 kW (b) 1 and 2 kW (c) 2 and 1 kW (d) 2 and 2 kW
T2 200 Q
32. Ans. (c) COP= = =2=
T1 − T2 300 − 200 W
Q
given Q = 2kW ∴ W = = 1kW
2
m
33. A Carnot refrigerator requires 1.5 kW/ton of refrigeration to maintain a region at a
temperature of – 30oC. The C.O.P. of the Carnot refrigerator is [IES-2003]
(a) 1.42 (b) 2.33 (c) 2.87 (d) 3.26
co
Q2 3.5
33. Ans. (b) COP of carnot refrigerator = = = 2.33 [ As 1TR ≈ 3.5 kW ]
W 1.5
35. A refrigerating machine working on reversed Carnot cycle consumes 6kW to produce
.
a refrigerating effect of 1000kJ/min for maintaining a region at -40oC.The higher
(a) 317.88
35. Ans. (b)
(b) 43.88
tas
temperature (in degree centigrade) of the cycle will be
(c) 23 (d) zero
[IAS-1997]
Q T2
COP = =
W T1 − T2
lda
(1000 / 60 ) 233
or =
6 T1 − 233
or T1 − 233 = 83.88 or T1 = 316.88K = 43.880 C
36. The C.O.P. of a Carnot refrigeration cycle decreases on [IAS 1994]

vi
(a) decreasing the difference in operating temperatures

(b) keeping the upper temperature constant and increasing the lower temperature
(c) increasing the upper temperature and keeping the lower temperature constant
(d) increasing the upper temperature and decreasing the lower temperature
Ci
T2
36. Ans. (c) COP of Carnot refrigerator will decrease if upper temperature T1 is
T1 − T2
increased and T2 keeping const.
w.
37. The working temperatures in evaporator and condenser coils of a refrigerator are
-23° C and 27° C respectively. The COP of the refrigerator is 0.8 of the maximum COP.
For a power input of 1 kW, the refrigeration effect produced will be [IES-2001]
(a) 4 kW (b) 5 kW (c) 8 kW (d) 2.5 kW
37. Ans. (a)
ww
39. The efficiency of a Carnot engine is given as 0·75. If the cycle direction is reversed,
what will be the value of C.O.P. for the Carnot refrigerator?
(a) 0·27 (b) 0·33 (c) 1·27 (d) 2·33 [IAS-2002]
39. Ans. (b)
1 1
1st method: (COP ) R = (COP) H . P − 1 = −1 = − 1 = 0.33
ηCarnot 0.75
T2 T 1 T2 1
2nd method: ηCarnot = 1 − = 0.75 or 2 = or = = 0.33 = (COP ) R
T1 T1 4 T1 − T2 4 − 1
40. A Carnot refrigerator works between the temperatures of 200 K and 300 K. If the
refrigerator receives 1 kW of heat the work requirement will be [IAS-2000]
(a) 0.5 kW (b) 0.67 kW (c) 1.5 kW (d) 3 kW
Q T2 1× ( 300 − 200 )
40. Ans. (a) COP = = or W = KW = 0.5KW
m
W T1 − T2 200
41. It is proposed to build refrigeration plant for a cold storage to be maintained at – 3oC.
The ambient temperature is 27°C. If 5 x 106 kJ/h of energy is to be continuously
co
removed from the cold storage, the MINIMUM power required to run the refrigerator will
be [IAS-1997]
(a) 14.3 kW (b) 75.3 kW (c) 154.3 kW (d) 245.3 kW
41. Ans. (c)
.
T2 270 Q Q 5 × 106
Maximum COP = = =9= or Wmin = = kW = 154.3kW
T1 − T2 300 − 270tas Wmin 9 9 × 3600
42. If an engine of 40 percent thermal efficiency drives a refrigerator having a coefficient

of performance of 5, then the heat input to the engine for each kJ of heat removed from
the cold body of the refrigerator is
lda
(a) 0.50kJ (b) 0.75kJ (c) 1.00 kJ (d) 1.25 kJ [IAS-1996]
42. Ans. (a)
W Q2
0.4 = ...............(i) 5= ..........................(ii)
Q1 W
Q2
∴ 0.4Q1 = or Q1 = 0.5Q2
5
vi
60. A heat engine with 30% efficiency drives a refrigerator of COP 5.0. What would be
the net heat input to the engine for each MW of heat removed in the refrigerator?
(a) 66.67 kJ (b) 600 kJ (c) 666.67 kJ (d) 6600 kJ [IES-2004]
60. Ans. (c) For each MW of heat removal in the refrigerator power needed to
Ci
1 MW
refrigerator= = 0.2MW
5
0.2 0.2
For 0.2 MW work output heat engine needed = = 666.67 kJ / s
η 0.3
w.
62. In the above figure, E is a heat engine with

efficiency of 0.4 and R is a refrigerator. Given that
Q2+Q4=3Q1 the COP of the refrigerator is
ww
(a) 2.5
(b) 3.0
(c) 4.0
(d) 5.0
[IES-1992]
Q2
62. Ans. (d) For heat engine, efficiency = 1 − = 0.4 or Q2 = 0.6Q1
Q1
And for refrigerator, W +Q = Q4 or (Q1 – Q2) + Q3 = Q4 or Q1 + Q3 = Q2+ Q4 = 3Q1
Therefore 2 Q1 = Q3
Q3 Q3 2Q1
COP of refrigerator = = = =5
W Q1 − Q2 Q1 − 0.6Q1
m
43. A reversible engine has ideal thermal efficiency of 30%. When it is used as a
refrigerating machine with all other conditions unchanged, the coefficient of performance
will be [IAS-1994, 1995]
(a) 3.33 (b) 3.00 (c) 2.33 (d) 1.33
co
43. Ans. (c)
.
tas
45. A Carnot cycle refrigerator operates between 250K and 300 K. Its coefficient of
performance is [GATE-1999]
lda
(a) 6.0 (b) 5.0 (c) 1.2 (d) 0.8
T2 250
45. Ans. (b) ( COP )R = = =5
T1 − T2 300 − 250
δQ
46. In the case of a refrigeration system undergoing an irreversible cycle, φ is…
T
vi
(a) < 0 (b) = 0 (c) > 0 (d) Not sure [GATE-1995]

46. Ans. (a)
Ci
Liquefaction of Gases
47. Where is an air refrigeration cycle generally employed? [IES-2006]
(a) Domestic refrigerators (b) Commercial refrigerators
(c) Air-conditioning (d) Gas liquefaction
47. Ans. (d)
w.
Production of Solid Ice

48. In a vapour compression refrigeration cycle for making ice, the condensing
temperature for higher COP [IES-2006]
ww
(a) Should be near the critical temperature of the refrigerant

(b) Should be above the critical temperature of the refrigerant
(c) Should be much below the critical temperature of the refrigerant
(d) Could be of any value as it does not affect the COP
48. Ans. (c)
49. Assertion (A): When solid CO2 (dry ice) is exposed to the atmosphere, it gets
transformed directly into vapour absorbing the latent heat of sublimation from the
surroundings. [IAS-1997]
Reason (R): The triple point of CO2 is at about 5 atmospheric pressure and at 216 K.
49. Ans. (a)
50. Assertion (A): Quick freezing of food materials helps retain the original texture of
food materials and taste of juices. [IES-1994]
Reason (R): Quick freezing causes the formation of smaller crystals of water which does
not damage the tissue cells of food materials.
50. Ans. (c) A is true but R is false.
m
Refrigeration capacity (Ton of refrigeration)
51. Assertion (A): The COP of an air-conditioning plant is lower than that of an ice plant.
Reason (R): The temperatures required in the ice plant are lower than those required for
co
an air-conditioning plant. [IAS-1997]
51. Ans. (d) The COP of an air-conditioning plant is higher than that of an ice plant.
52. One ton refrigeration is equivalent to [IES-1999]

(a) 3.5 kW (b) 50 kJ/s (c) l000 J/min (d) 1000 kJ/min
.
52. Ans. (a) tas N
53. The power (kW) required per ton of refrigeration is , where COP is the
COP
coefficient of performance, then N is equal to [IAS-2001]
(a) 2.75 (b) 3.50 (c) 4.75 (d) 5.25
lda
Q Q 12660
53. Ans. (b) COP = or W = if W is in KW, Q = kW = 3.52 kW
W COP 3600
54. Round the clock cooling of an apartment having a load of 300 MJ/day requires an
air-conditioning plant of capacity about [GATE-1993]
(a) 1 ton (b) 5 tons (c) 10 tons (d) 100 tons
vi
54. Ans. (a)

Ci
56. In a one ton capacity water cooler, water enters at 30oC at the rate of 200 litres per
hour. The outlet temperature of water will be (sp. heat of water =4.18 kJ/kg K)
w.
(a) 3.5°C (b) 6.3°C (c) 23.7 °C (d) 15°C [IES-2001; 2003]
56. Ans. (d)
3.516 × 3600 = 4.18 × 200 × (300 - x)
or x = 14.98°C ≈ 15°C
ww
57. A refrigerating machine having coefficient of performance equal to 2 is used to

remove heat at the rate of 1200 kJ/min. What is the power required for this machine?
(a) 80 kW (b) 60 kW (c) 20 kW (d) 10 kW [IES 2007]
Q Q 1200
57. Ans. (d) COP = or W = = = 10 kW
W COP 60 x 2
58. A Carnot refrigerator has a COP of 6. What is the ratio of the lower to the higher
absolute temperatures? [IES-2006]
(a) 1/6 (b) 7/8 (c) 6/7 (d) 1/7

T2 T 1 7 T 6
58. Ans. (c) ( COP ) R = = 6 or 1 = 1 + = ∴ 2 =
T1 − T2 T2 6 6 T1 7
3. A reversed Carnot cycle working as a heat pump has a COP of 7. What is the ratio of
minimum to maximum absolute temperatures? [IES-2005]
(a) 7/8 (b) 1/6 (c) 6/7 (d) 1/7
T1 T1 − T2 1 T2 6
( COP )H.P
m
3. Ans. (c) = =7 or = or =
T1 − T2 T1 7 T1 7
59. Which one of the following statements is correct? [IES-2004]
co
In a domestic refrigerator periodic defrosting is required because frosting
(a) causes corrosion of materials (b) reduces heat extraction
(c) overcools food stuff (d) partially blocks refrigerant flow
59. Ans. (b)
.
61. Consider the following statements:
tas [IES-1997]
In thermoelectric refrigeration, the coefficient of performance is a function of:
1. electrical conductivity of materials. 2. Peltier coefficient
3. Seebeck coefficient 4. temperature at cold and hot junctions.
5. thermal conductivity of materials.
lda
Of these statements
(a) 1, 3, 4 and 5 are correct (b) 1, 2, 3 and 5 are correct
(c) 1, 2, 4 and 5 are correct (d) 2, 3,4 and 5 are correct
61. Ans. (b) In thermoelectric refrigeration, there are no hot and cold junctions
63. When the lower temperature is fixed, COP of a refrigerating machine can be
vi
improved by [IES-1992]
(a) operating the machine at higher speeds (b) operating the machine at lower speeds
(c) raising the higher temperature (d) lowering the higher temperature
63. Ans. (d) In heat engines higher efficiency can be achieved when (T1 – T2) is higher.
Ci
In refrigerating machines it is the reverse, i.e. (T1 – T2) should be lower.
64. Assertion (A): Power input per TR of a refrigeration system increases with decrease
in evaporator temperature. [IAS-2004]
w.
Reason (R): C.O.P. of refrigeration system decreases with decrease in evaporator

temperature.
64. Ans. (a)
65. In a 0.5 TR capacity water cooler, water enters at 30°C and leaves at 15°C.What is
ww
the actual water flow rate? [IES-2005]

(a) 50 litres/hour (b) 75 litres/hour (c) 100 litres/hour (d) 125 litres/hour
65. Ans. (c) Q = mCP Δt or 0.5 × 12660 = m × 4.2 × ( 30 − 15 ) or m = 100kg / hr
Answers with Explanation (Objective)
m
. co
tas
vi lda
Ci
w.
ww
2. Vapour Compression System

Modifications in Reversed Carnot Cycle with Vapour as a Refrigerant
1. The schematic diagram of a vapour compression refrigeration system can be
m
represented as [IAS-1996]
. co
tas
lda
1. Ans. (b)
vi
Vapour Compression Cycle

2. In a vapour compression refrigeration plant, the enthalpy values at different points are:
Ci
(i) Enthalpy at exit of the evaporator = 350 kJ/kg [IES-2006]

(ii) Enthalpy at exit of the compressor 375 kJ/kg
(iii) Enthalpy at exit of the condenser = 225 kJ/kg
The refrigerating efficiency of the plant is 0·8. What is the power required per kW of
cooling to be produced?
w.
(a) 0·25 kW (b) 4·0 kW (c) 12·5 kW (d) 11 kW

2. Ans. (a)
h3 = h 4
Refrigerating effect (Qo)
ww
= (h1 - h4) x ɳr
= (350 – 225)x 0.8
= 100 kJ/kg
Compressor work (W) = (

h2 – h1 = 375 – 350 = 25
kJ/kg
W 25
The power required per kW of cooling = = kW/kW of cooling
Q 100
3. The values of enthalpy at the beginning of compression, at the end of compression

and at the end of condensation are 185 kJ/kg, 210 kJ/kg and 85 kJ/kg respectively. What
is the value of the COP of the vapour compression refrigeration system? [IES-2005]
(a) 0·25 (b) 5·4 (c) 4 (d) 1·35
(h1 − h4 ) (185 − 85 ) 100
m
3. Ans. (c) COP = = = =4
(h2 − h1 ) ( 210 − 185 ) 25
4. Replacing a water-cooled condenser with an air-cooled one in a vapour compression
co
refrigeration system with constant evaporator pressure results in [IAS-2000]
(a) increase in condensation pressure (b) decrease in pressure ratio
(c) increase in pressure ratio (d) increase in condensation temperature
4. Ans. (d)
Heat transfer co-efficient of gas very small compared to water hwater >> hair so for same
.
heat transfer temperature difference will be high
tas
Q = hw A ( ΔT ) w = hair A ( ΔT )air ,so ( ΔT )air > ( ΔT ) w
5. In a vapour compression refrigeration plant, the refrigerant leaves the evaporator at

195 kJ/kg and the condenser at 65 kJ/kg. For 1 kg/s of refrigerant, what is the
refrigeration effect?
lda
[IES-2005]
(a) 70 KW (b) 100 KW (c) 130 KW (d) 160 KW
5. Ans. (c) Q = m ( h1 − h4 ) = 1× (195 − 65 ) = 130kW
6. Consider the following statements in respect of absorption refrigeration and vapour

compression refrigeration systems: [IES-2003]
vi
1. The former runs on low grade energy.

2. The pumping work in the former is negligible since specific volume of strong
liquid solution is small.
3. The latter uses an absorber while former uses a generator.
Ci
4. The liquid pump alone replaces compressor of the latter.

Which of these statements are correct?
(a) 1 and 2 (b) 1 and 3 (c) 1 and 4 (d) 2 and 4
6. Ans. (a)
w.
7. A standard vapour compression refrigeration cycle consists of the following 4

thermodynamic processes in sequence: [IES-2002]
(a) isothermal expansion, isentropic compression, isothermal compression and
isentropic expansion
ww
(b) constant pressure heat addition, isentropic compression, constant pressure heat
rejection and isentropic expansion
(c) constant pressure heat addition, isentropic compression, constant pressure heat
rejection and isentropic expansion
(d) isothermal expansion, constant pressure heat addition, isothermal compression and
constant pressure heat rejection
7. Ans. (b)
8. For a heat pump working on vapour compression cycle, enthalpy values of the
working fluid at the end of heat addition process, at the end of compression process, at
the end of heat rejection process, and at the end of isenthalpic expansion process are
195 kJ/kg, 210 kJ/kg, and 90 kJ/kg respectively. The mass flow rate is 0.5 kg/s. Then the
heating capacity of heat pump is, nearly [IES-2001]
(a) 7.5 kW (b) 45 kW (c) 52.2 kW (d) 60 kW
8. Ans. (d)
9. The enthalpies at the beginning of compression, at the end of compression and at the
m
end of condensation are respectively 185 kJ/kg, 210 kJ/kg and 85 kJ/kg. The COP of the
vapour compression refrigeration system is [IES-2000]
(a) 0.25 (b) 5.4 (c) 4 (d) 1.35
co
9. Ans. (c)
10. In a vapour compression plant, if certain temperature differences are to be

maintained in the evaporator and condenser in order to obtain the necessary heat
transfer, then the evaporator saturation temperature must be [IES-1999]
.
(a) higher than the derived cold-region temperature and the condenser saturation
tas
temperature must be lower than the available cooling water temperature by sufficient
amounts
(b) lower than. the derived cold-region temperature and the condenser saturation
temperature must be lower than the available cooling water temperature by sufficient
amounts
lda
(c) lower than the derived cold-region temperature and the condenser saturation
temperature must be higher than the available cooling water temperature by sufficient
amounts
(d) higher than the derived cold-region temperature and the condenser saturation
temperature must be higher than the available cooling water temperature by sufficient
amounts
vi
10. Ans. (c)
11. The correct sequence of the given components of a vapour compression refrigerator
is
Ci
(a) evaporator, compressor, condenser and throttle valve [IES-1999]

(b) condenser, throttle valve, evaporator and compressor
(c) compressor, condenser, throttle valve and evaporator
(d) throttle valve, evaporator, compressor and condenser
w.
11. Ans. (c)
12. Consider the following statements: [IES-1998]

In a vapour compression system, a thermometer placed in the liquid line can indicate
whether the
ww
1. refrigerant flow is too low 2. water circulation is adequate.

3. condenser is fouled 4. pump is functioning properly.
Of these statements
(a) 1, 2 and 3 are correct (b) 1, 2 and 4 are correct
(c) 1, 3 and 4 are correct (d) 2, 3 and 4 are correct
12. Ans. (d) Thermometer in liquid line can't detect that refrigerant flow is too low.
In the case of a vapour compression machine, if the condensing temperature of the

refrigerant is closer to the critical temperature, then there will be [IES-1997]
1. excessive power consumption 2. high compression 3. large volume flow.
Of these statements
(a) 1, 2 and 3 are correct (b) 1 and 2 are correct (c) 2 and 3 are correct (d) 1 and 3 are
correct
13. Ans. (c) If the condensing temperature of the refrigerant is closer to the critical
temperature, compression will be high and large volume flow will take place.
m
14. A single-stage vapour compression refrigeration system cannot be used to produce
ultralow temperatures because [IES-1997]
(a) refrigerants for ultra-low temperatures are not available
co
(b) lubricants for ultra-low temperatures are not available
(c) volumetric efficiency will decrease considerably
(d) heat leakage into the system will be excessive
14. Ans. (a) Refrigerants for ultra-low temperatures are not available
.
15. In a vapour compression refrigeration system, a throttle valve is used in place of an
tas
expander because
(a) it considerably reduces the system weight
(b) it improves the COP, as the condenser is small. [IES-1996]
(c) the positive work in isentropic expansion of liquid is very small.
(d) it leads to significant cost reduction.
lda
15. Ans. (c) In a vapour compression refrigeration system, expander is not used
because the positive work in isentropic expansion of liquid is so small that it can't justify
cost of expander. Thus a throttle valve is used in place of expander.

A decrease in evaporator temperature of a vapour compression machine leads to
vi
1. an increase in refrigerating effect 2. an increase in specific volume of vapour

3. a decrease in volumetric efficiency of compressor
4. an increase in compressor work.
Of these statements
Ci
(a) 1,3 and 4 are correct (b) 1,2 and 3 are correct
(c) 2,3 and 4 are correct (d) 2 and 4 are correct.
16. Ans. (a)
w.
17. Assertion (A): In remote places, the use of absorption refrigeration system plant is
more advantageous when compared to vapour compression plant. [IES-1993]
Reason (R): The absorption system can use relatively low temperature heat as energy
source.
17. Ans. (c) Assertion A is correct but reason is not true. The correct reason should have
ww
been that no electricity is required for operation of absorption refrigeration system plant.
18. In a vapour compression refrigeration plant, the refrigerant leaves the evaporator at
195 kJ/kg and the condenser at 65 kJ/kg. For every kg of refrigerant the plant can supply
per second, a cooling load of [IES-1993]
(a) 70 kW (b) 100 kW (c) 130 kW (d) 160 kW
18. Ans. (c) h1 = 195 kJ/kg and h3 = 65 kJ/kg.
Since there is no heat transfer in throttling, h3 = h4
Refrigeration effect = h1 - h4 = 195 – 65 = 130 kJ/kg
19. Consider the following statements: [IAS-2007]

1. The work of compressor in vapour compression refrigeration system increases
with superheat of the suction vapour.
2. The work of compressor depends on the pressure difference rather than the
temperature difference of evaporator and condenser.
3. The coefficient of performance is within the range of 3 to 6 except at very low
temperature when it may be less than 1.
Which of the statements given above are correct?
m
(a) 1, 2 and 3 (b)1 and 2 only (c) 1 and 3 only (d) 2 and 3 only
19. Ans. (a)
co
20. Consider the following statements pertaining to a vapour compression type
refrigerator:
1. The condenser rejects heat to the surroundings from the refrigerant. [IAS-2002]
2. The evaporator absorbs heat from the surroundings to be cooled.
3. Both the condenser and evaporator are heat exchangers with refrigerant as a
.
common medium. tas
4. The amount of heat exchanged in condenser and evaporator are equal under steady
conditions.
Which of the above statements are correct?
(a) 1 and 2 (b) 1, 2 and 3 (c) 1, 2 and 4 (d) 2, 3 and 4
20. Ans. (b)
lda
21. In a vapour compression cycle, the refrigerant, immediately after expansion value is
(a) saturated liquid (b) subcooled liquid (c) dry vapour (d) wet vapour
[IAS-2002]
21. Ans. (d)
In P-h diagram it is point 4’or 4 both are
vi
very wet vapour.

Ci
w.
22. Assertion (A): In a vapour compression refrigeration system, the condenser pressure
ww
should be kept as low as possible.

Reason (R): Increase in condenser pressure reduces the refrigerating effect and
increases the work of compression. [IAS-1999]
22 Ans. (a)
23. Match List I (T-s diagram) with List II (P-h diagrams) of vapour compression
refrigeration cycles and select the correct answer using the codes given below the lists:
m
. co
tas
lda
Codes: A B C D A B C D [IAS-1999]
(a) 1 4 2 3 (b) 1 4 3 2
(c) 4 1 3 2 (d) 4 1 2 3
23. Ans. (b)
vi
24. Theoretical vapour compression refrigeration cycle is represented on a T-s diagram

as [IAS-1997]
Ci
w.
24. Ans. (c)

ww
25. In an ideal vapour compression refrigeration cycle, the enthalpy of the refrigerant
before and after the evaporator are respectively 75 kJ/hg and 180 kJ/kg. The circulation
rate of the refrigerant for each ton of refrigeration is [IAS-1997]
(a) 1 kg/min (b) 2 kg/min (c) 3 kg/min (d) 4 kg/min
211
25. Ans. (b) Q = m (h1 - h4) = m (180-75) = 211 or m = = 2kg/min
105
26. In an ideal vapour compression refrigeration cycle, the enthalpy of the refrigerant at
exit from the condenser, compressor and evaporator is 80 kJ/kg, 200 kJ/kg and 180
kJ/kg respectively. The coefficient of performance of the cycle is
(a) 6 (b) 5 (c) 3.5 (d) 2.5 [IAS-1996]
26. Ans. (b) h3 = h4 = 80 kJ/kg
h1=180 kJ/kg and h2=200 kJ/kg
WC = h2 - h1 = 200 -180 = 20 KJ/kg
Q = h1 - h4 = 180 – 80 = 100 KJ/kg
m
Q 100
∴ COP = = =5
Wc 20
co
27. The correct sequence of vapour compression (VC), vapour absorption (VA) and
.
steam ejector (SE) refrigeration cycles in increasing order of the C.O. P is [IAS-1995]
tas
(a) VC, VA, SE (b) VA, SE, VC (c) SE, VC, VA (d) SE, VA, VC
27. Ans. (b) The correct sequence of VC, VA and SE in increasing order of COP is VA,
SE and VC, the Value being of the order of 0.3 to 0.4 0.5 to 0.8 and 4 to 5 respectively.
28. The vapour compression refrigeration cycle is

lda
represented as shown in the figure below, with
state 1 being the exit of the evaporator. The
coordinate system used in this figure is
(a) p-h (b) T-s
(c) p-s (d) T-h
vi
Ci
[GATE-2005]
28. Ans. (a)
29. In a vapour compression refrigeration system, liquid to suction heat exchanger is

used to
w.
(a) Keep the COP constant [GATE-2000]

(b) prevent the liquid refrigerant from entering the compressor
(c) subcool the liquid refrigerant leaving the condenser
(d) subcool the vapour refrigerant from the evaporator
29. Ans. (c)
ww
Data for Q. 30 – 31 are given below. Solve the problems and choose correct
answers.
A refrigerator based on ideal vapour compression cycle operates between the
temperature limits of -20°C and 40°C. The refrigerant enters the condenser as saturated
vapour and leaves as saturated liquid. The enthalpy and entropy values for saturated
liquid and vapour at these temperatures are given in the table below.
30. If refrigerant circulation rate is 0.025 kg/s, the refrigeration, effect is equal to
(a) 2.1 kW (b) 2.5 kW (c) 3.0 kW (d) 4.0 kW [GATE-2003]
30. Ans. (a)
m
. co
tas
lda
31. The COP of the refrigerator is [GATE-2003]

vi
(a) 2.0 (b) 2.33 (c) 5.0 (d) 6.0

31. Ans. (b)
Ci
32. A refrigerating system operating on reversed Brayton refrigeration cycle is used for
w.
maintaining 250K. If the temperature at the end of constant pressure cooling is 300 K
and rise in the temperature of air in the refrigerator is 50 K, then the net work of
compression will be (assume air as the working substance with cp = kJ per kg per°C)
(a) 250 kJ/kg (b) 200 kJ/kg (c) 50kJ/kg (d) 25kJ/kg [IES-1993]
ww
32. Ans. (d) Figure

shows the reversed
Brayton refrigeration
cycle.
Various values are
shown.
Net work of compression
= (h2 – h1) - (h3 - h4)
m
T2 T3
Now =
T1 T4
300
or T2 = × 250 = 375
co
200
Net work = (375 - 250) - (300 - 200) = 25 and Net work = 25 x Cp = 25 kJ/kg
33. Match List-I (Effect) with List-II (Process) in the case of an ideal refrigeration cycle
and select the correct answer using the codes given below the Lists:
.
[IAS-1997]
List-I tas List-II
A. Work input 1. Constant pressure at higher temperature
B. Heat rejection 2. Isentropic compression
C. Expansion 3. Constant temperature at lower pressure
D. Heat absorption 4. Adiabatic
Codes: A B C D A B C D
lda
(a) 4 1 2 3 (b) 2 3 4 1
(c) 2 1 4 3 (d) 4 2 3 1
33. Ans. (c)
Actual Vapour Compression Cycle

vi
34. Assertion (A): Subcooling of refrigerant liquid increases the coefficient of

performance of refrigeration. [IES-2004]
Reason (R): Subcooling reduces the work requirement of a refrigeration cycle.
Ci
34. Ans. (c) Sub cooling ↑ Refrigerating effect thus ↑ COP but has no effect on
compressor work (Wc).
35. Subcooling heat exchanger is used in a refrigeration cycle. The enthalpies at

condenser outlet and evaporator outlet are 78 and 182 kJ/kg respectively. The enthalpy
w.
at outlet of isentropic compressor is 230 kJ/kg and enthalpy of subcooled liquid is 68

kJ/kg. The COP of the cycle is [IES-2002]
(a) 3.25 (b) 2.16 (c) 3.0 (d) 3.5
35. Ans. (c)
ww
36. The performance of an evaporator condenser largely depends on [IES-1999]

(a) dry bulb temperature of air (b) wet bulb temperature of air
(c) hot water temperature (d) air-conditioned room temperature
36. Ans. (a)
37. Which one of the following is the p-v diagram for air refrigeration cycle?
m
. co
37. Ans. (a)
tas
38. Match items in List I with those in List II and III and select the correct answer.
List I List II List III [IES-1996]
A. Reversed Carnot engine 1. Condenser 6. Generator
lda
B. Subcooling 2. Evaporator 7. Increase in refrigerating effect.
C. Superheating 3. Vortex refrigerator 8. Highest COP.
D. Constant enthalpy 4. Throttling 9. Adiabatic.
5. Heat pump 10. Dry compression.
Code: A B C D A B C D
(a) 3,10 1,7 2,9 4,6 (b) 5,8 1,7 2,10 4,9
vi
(c) 4,10 3,8 3,10 1,6 (d) 2,7 5,8 4,6 1,9
38. Ans. (b) Reversed Carnot engine is used for heat pump and it has highest COP.
Thus for A, the correct choice from List II and List III is 5, 8. Sub cooling occurs in
condenser and it increases refrigeration effect. Therefore for B, the correct choice from
Ci
List II and III is 1, 7.

Superheating occurs in evaporator and it is involved in dry compression. Thus for Part C
in List I, the correct choice from Lists IT and III is 2, 10. Constant enthalpy process takes
place during throttling and is basically adiabatic process. This D is matched with 4,9.
w.
39. The figure given above depicts saturation

dome for water on the temperature-entropy
plane. What is the temperature difference
ΔT shown on a typical isobar line known as?
ww
(a) Degree of wet bulb depression

(b) Degree of saturation
(c) Degree of sub cooling
(d) Degree of reheat
[IES-2006]
39. Ans. (c)
40. The operating temperature of a cold storage is - 2°C. Heat leakage from the
surrounding is 30 kW for the ambient temperature of 40°C. The actual COP of the
refrigeration plant used is one-fourth that of an ideal plant working between the same
temperatures. The power required to drive the plant is [IES-1994]
(a) 1.86 kW (b) 3.72 kW (c) 7.44 kW (d) 18.60 kW
40. Ans. (d) COP of ideal plant working between limits -2 and 40°C, i. e. 271 and 313 K
T1 271
is = = 6.45 , So COP of refrigeration plant = 6.45/4 =1.61
m
T2 − T1 313 − 271
heat abstracted 30
COP = or Work required = = 1.86 KW
Work required 1.61
co
41. Consider the following steps: [IES-1994]
1. Starting of compressor 2. Starting of cooling tower pump.
3. Starting of chiller water pump 4. Starting of blower motor of cooling coil.
.
The correct sequence of these steps in the starting of a cell air-conditioning plant using
chilled water cooling coil, is tas
(a) 3,1,4,2 (b) 1,3,2,4 (c) 3,2,1,4 (d) 1,3,4,2
41. Ans. (c) The correct sequence in starting of a central air conditioning plant using
chilled water cooling coil is starting of chiller water pump, starting of cooling tower pump,
starting the compressor, starting of blower motor of cooling coil.
lda
42. A refrigerator storage is supplied with 3600 kg of fish at a temperature of 27°C. The
fish has to be cooled to -23°C for preserving it for a long period without deterioration.
The cooling takes place in 10 hours. The specific heat of fish is 2·0 kJ/kgK above
freezing point of fish and 0·5 kJ/kgK below freezing point of fish, which is -3°C. The
latent heat of freezing is 230 kJ/kg. What is the power to drive the plant if the actual COP
is half that of the ideal COP? [IAS-2002]
vi
(a) 30 kW (b) 15 kW (c) 12 kW (d) 6 kW

1 1 T 1 250
42. Ans. (c) (COP) actal = (COP)ideal = × 2 = × = 2.5
2 2 T1 − T2 2 300 − 250
Ci
Total Heat transfer (Q) = m.c pbf ( ΔT )before freeze + m.c paf ( ΔT )after freeze
= 3600[2 × 30 + 230 + 0.5 × 20] kJ = 3600 × 300 kJ
Q 3600 × 300
Rate of heat transfer = = = 30 kW
w.
t 10 × 3600
Q Q 30
COP = or W = = = 12 kW
W COP 2.5
ww

High condenser pressure in a refrigeration system can occur because
1. the water flow rate is lower than the desired value.
2. non-condensable gases are present in the system
3. of accumulation of lubricating oil in condenser
4. of low charge of refrigerant in the system.
Of these statements
(a) 1, 3 and 4 are correct (b) 1, 2 and 3 are correct
(c) 1, 2 and 4 correct (d) 2, 3 and 4 are correct
43. Ans. (b)
44. Excessive pressure drop in liquid line in a refrigerating system causes [IAS-1998]
(a) high condenser pressure (b) flashing of the liquid refrigerant
(c) higher evaporator pressure (d) under cooling of the liquid refrigerant
44. Ans. (b)
45. In system A vapour are superheated by 10°C in the evaporator while in system B
vapour are superheated by 10°C in a liquid vapour regenerative heat exchanger, other
m
conditions being the same. Then
(a) C.O.P. of A = C.O.P. of B [IAS-2002]
(b) C.O.P. of both A and B > C.O.P. of Reversed Carnot Cycle
co
(c) C.O.P. of A > C.O.P. of B
(d) C.O.P. of A < C.O.P. of B
45. Ans. (a)
h1′ − h1 = h3 − h3′
.
For regeneration as h1′ − h4 = h1 − h4′
∴ COP is same
tas
lda
Heat Pump
vi
Second Law Efficiency of Vapour Compression Cycle

Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
3.
Refrigerants
m
1. A good refrigerant should have
co
(a) large latent heat of vaporisation and low operating pressures
(b) small latent heat of vaporisation and high operating pressures
(c) large latent heat of vaporisation and large operating pressures
(d) small latent heat of vaporisation and low operating pressures
.
1. Ans. (a)
tas
2. The desirable combination of properties for a refrigerant include
(a) high specific heat and low specific volume
[IES-1998]
(b) high heat transfer coefficient and low latent heat

(c) high thermal conductivity and low freezing point
(d) high specific heat and high bailing point
lda
2. Ans. (a) High thermal conductivity enables better heat transfer in evaporator and
condenser. Lower specific volume implies smaller compressor can be used and
refrigerating effect per kg of refrigerant increases.
3. Match List II with List II and select the correct answer using the codes given below the
vi
lists:
List I (Refrigerant) List II (Principal application) [IES-1995]
A. Air 1. Direct contact freezing of food
B. Ammonia 2. Centrifugal compressor system
Ci
C. Carbon dioxide 3. Large industrial temperature installation

D. Refrigerant-II 4. Automotive air-conditioners
5. Aircraft refrigeration
(a) 4 3 1 2 (b) 5 3 1 2
w.
(c) 2 4 3 5 (d) 5 3 2 1
3. Ans. (b)
4. Which 'of the following statements are true for Ammonia as a refrigerant?
ww
1. It has higher compressor discharge temperature compared to fluorocarbons.

2. It is toxic to mucous membranes.
3. It requires larger displacement per TR compared to fluorocarbons.
4. It reacts with copper and its alloys.
Select the correct answer using the codes given below: [IES-1993]
Codes:
4. Ans. (c)
5. A good refrigerant should have:

(a) High latent heat of vaporization and low freezing point [IES-1992]
(b) High operating pressure and low freezing point
(c) High specific volume and high latent heat of vaporization.
(d) Low COP and low freezing point.
5. Ans. (a)
6. Which of the following refrigerant has the maximum ozone depletion in the
stratosphere?
m
[IES-1992]
(a) Ammonia (b) Carbon dioxide (c) Sulphur dioxide (d) Fluorine
6. Ans. (d)
co
7. Assertion (A): R-22 is used as a refrigerant in all refrigerators.
Reason (R): R-22 is non – toxic and non – inflammable. [IAS-1998]
7. Ans. (d)
.
Designation of Refrigerants tas
8. Consider the following statements regarding refrigerants: [IES-2000]
1. Refrigerant NH3 is used in reciprocating compressors.
2. Refrigerant CO2 is used in reciprocating compressors.
3. Refrigerant R-11 is used in centrifugal compressors.
lda
(a) 1 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
8. Ans. (d)
9. Environment friendly refrigerant R134a is used in the new generation domestic

refrigerators. Its chemical formula is [GATE-2004]
(a) CH ClF2 (b) C2 Cl3 F3 (c) C2 Cl2 F4 (d) C2 H2 F4
vi
9. Ans. (d)
Ci
w.
10. Match List-I (Refrigerant) with List-II (Chemical constituent) and select the correct
answer using the codes given below the lists: [IES-2001]
ww
List-I (Refrigerant) List -II (Chemical constituent)

A. R-12 1. Trichlorotrifluroethane (CCl2FCClF2)
B. R-22 2. Difluoro monochloro methane (CHF2CI)
C. R-717 3. Ammonia (NH3)
D. R-113 4. Difluoro dichloro methane (CCl2F2)
(a) 3 2 4 1 (b) 4 2 3 1
(c) 3 1 4 2 (d) 4 1 3 2
10. Ans. (b)
11. Match List I (Chemical formula of refrigerant) with List II (Numerical Designation) and
select the correct answer using the codes given below the lists:
List I List II [IAS-2002]
(Chemical formula of refrigerant) (Numerical Designation)
A. NH3 1. 12
B. CCl2F2 2. 22
C. CHClF2 3. 40
D. CCl2 FCCl F2 4. 113
m
5. 717
(a) 4 1 5 2 (b) 5 3 2 4
co
(c) 4 3 5 2 (d) 5 1 2 4
11. Ans. (d) R(C-1)(H+1)F and Cl by balance
And for inorganic refrigerant R (700+Molecular weight)
12. Match List I with List II and select the correct answer using the codes given below
.
the Lists: tas
A. Refrigerant 11 1. CC12F2
B. Refrigerant 12 2. C2Cl2F4
C. Refrigerant 22 3. CCl3F
D. Refrigerant 114 4. CHClF2
lda
5. CH2ClF
(a) 2 1 5 3 (b) 3 4 5 2
(c) 3 1 4 2 (d) 5 1 4 3
12. Ans. (c)
R ( C − 1)( H + 1) F ∴R11 = R 011 ⇒ C = 1, H = 0, F = 1, Cl = 3
vi
∴R12 = R012 ⇒ C = 1, H = 0, F = 2, Cl = 2
∴R 22 = R 022 ⇒ C = 1, H = 1, F = 2, Cl = 1
Ci
∴R114 = R114 ⇒ C = 2, H = 0, F = 4, Cl = 2
13. The refrigerant - 12 (R – 12) used in vapour compression refrigeration system is

(a) CHCIF2 (b) CCl2F2 (c) CHCl2F (d) CCIF3 [IAS-2000]
w.
13. Ans. (b) R12 = R012 = R(C-1)(H+1)F Therefore C = 1, H = 0, F = 2

by balance Cl = 2
the lists: [IAS-1999]
ww
List I (Refrigerant) List II (Designation)

A. Dichlorodifluoromethane 1. R 718
B. Water 2. R 22
C. Methyl chloride 3. R40
D. Monochloride-fluoromethane 4. R 12
(a) 4 1 2 3 (b) 1 4 3 2
(c) 1 4 2 3 (d) 4 1 3 2
14. Ans. (d)
Secondary Refrigerants
1. Practically all common refrigerants have approximately the same COP and
power requirement.
m
2. Ammonia mixes freely with lubricating oil and this helps lubrication of
compressors.
3. Dielectric strength of refrigerants is an important property in hermetically sealed
compressor units.
co
4. Leakage of ammonia can be detected by' halide torch method.
Of these statements
(a) 1, 2 and 4 are correct (b) 2 and 4 are correct (c) 1, 3 and 4 are correct (d) 1 and 3
are correct
.
15. Ans. (d) Practically all refrigerants, except CO2 have fairly same COP and power
requirements. Thus statement (a) is correct.
tas
Ammonia does not mix freely with lubricating oil. Therefore statement (b) is wrong.
Dielectric strength of refrigerants is an important property in hermetically sealed
compressor units.
Leakage of ammonia is detected by its odour or sulphur candle with which ammonia
forms white smoke like fumes. Thus statements 1 and 4 are correct and choice (d) is the
lda
right choice.
16. In milk chilling plants, the usual secondary refrigerant is [IES-1998]

(a) ammonia solution (b) sodium silicate (c) glycol (d) brine
16. Ans. (c)
vi
17. Assertion (A): Freon-12 is odourless and its leakage cannot be easily detected.
However, it is preferred in comfort air-conditioning. [IAS 1994]
Reason (R): It is almost impossible for Freon-12 leakage to attain a fatal concentration.
Ci
17. Ans. (a)
18. The leakage in a Freon-based refrigeration system can be detected by using a/an
(a) oxy-acetylene torch (b) halide torch [IES-2000]
(c) sulphur torch (d) blue litmus paper
w.
18. Ans. (b)
19. Match List I with List II and select the correct answer [IES-1994]
List I List II
A. Freon 12 1. Centrifugal systems
ww
B. Freon 22 2. Low temperature cold storage

C. Freon 11 3. Window type a/c units
D. Ammonia 4. Ice plants
(a) 3 2 1 4 (b) 3 1 2 4
(c) 1 2 4 3 (d) 1 3 4 2
19. Ans. (a)
20. The pipes and fitting in an ammonia refrigeration system should be made of
(a) cast steel or wrought iron (b) aluminium (c) naval brass (d) copper [IAS-1998]
20. Ans. (a)
Substitutes for CFC Refrigerants
Azeotropic Mixtures
m
21. Match List-I with List-II and select the correct answer using the codes given below
the lists: [IAS-2004]
List-I List-II
A. Sulphur candle test 1. Propane
co
B. Halide torch test 2. Ammonia
C. Soap and water test 3. Halocarbon refrigerants
D. Ammonia swab test 4. Sulphur dioxide
.
(a) 2 3 1 4 (b) 4 1 3 2
(c) 2
21. Ans. (a)
1 3 4 tas (d) 4 3 1 2

1. In Freon 22 system, moisture chocking generally does not occur.
2. Freon 11 is mainly used in large capacity air-conditioning plants with centrifugal
lda
compressor.
3. Pressure of lubricating oil in evaporator will increase the heat transfer coefficient.
4. Refrigerants that are completely miscible with oil, do not cause oil chocking.
Of these statements:
(a) 1, 2 and 3 are correct (b) 1, 2 and 3 correct
(c) 2, 3 and 4 correct (d) 1, 3 and 4 are correct
vi
22. Ans. (b)
23. Which one of the following refrigerants has the highest critical temperature?
Ci
(a) Water (b) Carbon dioxide (c) Freon 12 (d) Ammonia [IAS-1996]
23. Ans. (a)
24. The significant advantage of using ammonia as a refrigerant is its [IAS-1996]

(a) characteristic odour (b) high latent heat (c) solubility (d) inflammability
w.
24. Ans. (b)
25. The use of Refrigerant - 22 (R-22) for temperatures below - 30°C is not
recommended due to its [GATE-1993]
ww
(a) good miscibility with lubricating oil (b) poor miscibility with lubricating oil
(c) low evaporating pressure (d) high compressor discharge temperature
25. Ans. (d)
26. Selection of a refrigerant for a vapour – compression system depends on which

among the following? [IES 2007]
(a) Toxicity (b) Environmental effect
(c) Saturation pressure – temperature relationship (d) All of the above
26. Ans. (d)
27. Which one of the following is the fluid whose properties in all its three phase are
made use of in thermodynamics?
(a) Ammonia (b) Freon 12
(c) Helium (d) Water [IES 2007]
27. Ans. (d)
28. Oil separator is NOT required in refrigeration system if [IES-2003]

(a) refrigerant and oil are immiscible at all pressures and temperatures
m
(b) refrigerant and oil are immiscible at condensation pressure and temperature
(c) refrigerant and oil are miscible at all pressures and temperatures
(d) refrigerant and oil are miscible at condensation pressures and temperature.
co
28. Ans. (c)
29. Ozone depletion by CFCs occurs by breakdown of [IES-2002]

(a) chlorine atoms from refrigerant by UV radiation and reaction with ozone in
troposphere
.
(b) fluorine atoms from refrigerant by UV radiation
tas and reaction with ozone in
troposphere
(c) chlorine atoms from refrigerant by UV radiation and reaction with ozone in
stratosphere
(d) fluorine atoms from refrigerant by U V radiation and reaction with ozone in
stratosphere
lda
29. Ans. (c)

In ammonia refrigeration systems, oil separator is provided because
1. Oil separation in evaporator would lead to reduction in heat transfer coefficient.
2. Oil accumulation in the evaporator causes choking of evaporator.
vi
3. Oil is partially miscible in the refrigerant.

4. Oil causes choking of expansion device.
Of these statements
(a) 1 and 2 are correct (b) 2 and 4 are correct
Ci
(c) 2, 3 and 4 are correct (d) 1, 3 and 4 are correct

30. Ans. (b)

w.
Moisture should be removed from refrigerants to avoid

1. compressor seal failure. 2. freezing at the expansion valve.
3. restriction to refrigerant flow. 4. corrosion of steel parts.
Of these statements
(a) 1, 2, 3 and 4 are correct (b) 1 and 2 are correct
ww
(c) 2, 3 and 4 are correct (d) 1, 3 and 4 are correct.

31. Ans. (a) All the statements about effect of moisture on refrigerant are correct.
32. The color of the flame of halide torch, in a case of leakage of Freon refrigerant, will
change to
(a) bright green (b) yellow (c) red (d) orange [IAS-1996]
32. Ans. (a)
33. The leaks in a refrigeration system Freon are detected by: [IES-2006]
(a) A halide torch, which on detecting produces greenish flame light

(b) Sulphur sticks, which on detecting give white smoke
(c) Using reagents
(d) Sensing reduction in pressures
33. Ans. (a)
34. Ideal refrigeration mixture is one which [IAS-2007]

(a) Obeys Raoult's law in liquid phase and does not obey Dalton's law in vapour phase
(b) Does not obey Raoult's law in liquid phase and does not obey Dalton's law in vapour
m
phase
(c) Obeys Raoult's law in liquid phase and obeys Dalton's law in vapour phase
(d) Does not obey Raoult's law in liquid phase and obeys Dalton's law in vapour phase
co
34. Ans. (c)
.
tas
vi lda
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
4. Refrigerant Compressors
Highlight
For gas compressor [always use Reversible process]
m
a. Work required for Reversible polytropic compression
(n −1 )
n ⎡ ⎤
W= P1V1 ⎢ ⎛⎜ P2 ⎞⎟ n (all n)
n −1 − 1⎥
⎢⎜ P ⎟
co
⎥
⎢⎣ ⎝ 1 ⎠ ⎥⎦
b. Work required for Reversible Adiabatic compression
γ ⎡
⎛ ⎞
(γ −1 )
⎤
W= P1V1 ⎢ ⎜ 2 ⎟ γ
P
− 1⎥ (all γ)
γ −1
.
⎢ ⎜⎝ P1 ⎟⎠ ⎥
⎢⎣ tas ⎦⎥
c. But Work required when polytropic as well as adiabatic compression
γ ⎡ (n −1 )
⎤
W= P1V1 ⎢ ⎛⎜ P2 ⎞⎟ (mix of n and γ)
− 1⎥
n
γ −1 ⎢⎜ P ⎟ ⎥
⎢⎣ ⎝ 1 ⎠ ⎥⎦
lda
[Note: In reversible polytropic there is heat transfer but in this case,
adiabatic, heat transfer is not there.]
vi
Ci
w.
ww
Types of Compressors
1. Match List I with II and select the correct answer using the code given below the
m
Lists:
List I List II
(Name of Equipment) (Pressure Ratio)
A. Fan 1. 1.1
co
B. Blower 2. 2.5
C. Centrifugal air compressor 3. 4
D. Axial flow air compressor 4. 10
Code: [IES - 2007]
.
A B C D A B C D
(a) 2 1 3 4 tas (b) 1 2 3 4
(c) 1 2 4 3 (d) 2 1 4 3
1. Ans. (b)
2. Which of the following can be the cause/causes of an air-cooled compressor getting

lda
overheated during operation?
1. Insufficient lubricating oil. [IES-2006]
2. Broken valve strip.
3. Clogged intake filter.
Select the correct answer using the code given below:
(a) Only 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) 1, 2 and 3
vi
2. Ans. (d)
3. Which type of valves is generally used in reciprocating refrigerant compressors?

Ci
(a) Mushroom valve (b) Puppet valve [IES-2006]

(c) Plate valve (d) Throttle valve
3. Ans. (c)

w.
In reciprocating compressors, one should aim at compressing the air

(a) adiabatically (b) isentropically (c) isothermally (d) poly tropically
4. Ans. (c)
5. Roots blower is an example of

ww
[IES-2003]
(a) Reciprocating (positive displacement) compressor
(b) Rotary (positive displacement) compressor
(c) Centrifugal compressor
(d) Axial compressor
5. Ans. (b)
6. Match List I with List II and select the correct answer: [IES-2002]
List I List II
(Refrigeration equipment) (Characteristic)

A. Hermetically sealed compressor 1. Capillary tube
B. Semi-hermitically sealed compressor 2. Both compressor and motor enclosed in a
shell or casting
C. Open type compressor 3. Both compressor and motor enclosed in a
shell or casing with a removable cylinder
cover
D. Expansion device 4. Driving motor of enclosed in a shell or
casing and connected to the shaft driving
m
the compressor
A B C D A B C D
(a) 1 4 3 2 (b) 2 3 4 1
co
(c) 1 3 4 2 (d) 2 4 3 1
6. Ans. (b)
7. The capacity of an air compressor is specified as 10 m3/min. It means that the

compressor is capable of [IES-2000]
.
(a) supplying 3 m3 of compressed air per minute
tas
(b) compressing 3 m3 of free air per minute
(c) supplying 3 m3 of compressed air at NTP
(d) compressing 3 m3 of standard air per minute
7. Ans. (a)
lda
8. Which one of the following pairs of features and compressors type is NOT correctly
matched? [IES-2000]
(a) Intake and delivery ports compression is attained by: Vane compressor back flow
and internal compression cylindrical rotor set to eccentric casing
(b) Intermittent discharge requires receiver, produces high : Reciprocating compressor
pressure, slow speed and lubricati0n problems
vi
(c) Continuous flow, radial now, handles large volume : Centrifugal compressor
much higher speed and fitted into design of aero-engine
(d) Successive pressure drops through contracting : Axial flow compressor
passages, blades are formed from a number of circular arcs, axial now
Ci
8. Ans. (c)
9. When a burnt out hermetic compressor is replaced by a new one, it is desirable to

include in the system a large drier-cum ·strainer also. This is to be placed in [IES-1999]
w.
(a) liquid line (b) suction line (c) hot gas line (d) discharge line
9. Ans. (d)
10. Assertion (A): A reciprocating air compressor at sea level would deliver a greater
mass of air than a compressor on a mountain. [IES-1998]
ww
Reason (R): The compressor ratings are given for "free air".
10. Ans. (b)
11. What is the preferred intercooler pressure for a two stage air compressor working
between the suction pressure ps and the delivery pressure Pd? [IES-2006]
(a) (ps + pd)/2 (b) (ps + pd)/2 (c) (ps + pd)1/2 (d) (ps + pd)1/4
11. Ans. (c)
12. When are shock waves formed in air compressors? [IES-2006]
(a) Mach number < 0.9 (b) Mach number> 0·9

(c) Mach number = 2
(d) Mach number changes suddenly from one value to another
12. Ans. (b)
13. Assertion (A): In multi-stage compressors, the polytropic efficiency is always greater
than the isentropic efficiency. [IES-2005]
Reason(R): Higher the pressure ration, the greater is the polytropic efficiency.
13. Ans. (b)
m
14. For a two-stage reciprocating air compressor, the suction pressure is 1.5 bar and the
delivery pressure is 54 bar. What is the value of the ideal intercooler pressure?
co
(a) 6 bar (b) 9 bar (c) 27.75 bar (d) 9/ 2 bar [IES-2004]
14. Ans. (b) Pi = PP1 2 = 54 × 1.5 = 9 bar
15. During steady flow compression process of a gas with mass flow rate of 2 kg/s.
.
increase in specific enthalpy is 15kJ/kg and decrease in kinetic energy is 2 kJ/kg. The
compressor is
(a) 23 kW (b) 26kW
tas
rate of heat rejection to the environment is 3kW. The power needed to drive the
(c) 29kW (d) 37 kW [IES-2003]

15. Ans. (c) Power needed to drive the compression
v12 v2
Using, S.F.E.E., we get: h1 + + Q = h2 + 2 + W
lda
2 2
W = - 3 - 30 + 4 = - 29 kW
16. In a two-stage compressor with ideal intercooling, for the work requirement to be
minimum, the intermediate pressure Pi in terms of condenser and evaporator pressure
Pc and pe respectively is [IES-2003]
vi
(a) pi = pc pe (b) pi = pc pe (c) pi = pc / pe (d) pi = pc / pe

16. Ans. (b)
Ci
17. When a refrigerator system is started from ambient conditions, the evaporator
temperature decreases from ambient temperature to design value. This period is known
as a pull-down period. The power requirement of compressor during pull-down
(a) decreases continuously (b) increases continuously [IES-2003]
w.
(c) remains constant (d) increases and then decreases

17. Ans. (b)
p2
18. If n is the polytropic index of compression and is the pressure ratio for a three-
p1
ww
stage compressor with ideal intercooling, the expression for the total work of three stage
is [IES-2001]
⎧ ( n −1) ⎫ ⎧ ( n −1) ⎫
3n ⎪⎛ p2 ⎞ n ⎪ n ⎪⎛ p2 ⎞ 3n ⎪
(a) p1v1 ⎨⎜ ⎟ − 1⎬ (b) p1v1 ⎨⎜ ⎟ − 1⎬
( n − 1) ⎪⎝ p1 ⎠ ⎪ ( n − 1) ⎪⎝ p1 ⎠ ⎪
⎩ ⎭ ⎩ ⎭
⎧ ( n −1) ⎫ ⎧ ( n −1) ⎫
n ⎛ ⎞
⎪ p2 n ⎪ 3n ⎛ ⎞
⎪ p2 3n ⎪
(c) p1v1 ⎨⎜ ⎟ − 1⎬ (d) p1v1 ⎨⎜ ⎟ − 1⎬
( n − 1) ⎪⎝ p1 ⎠ ⎪ ( n − 1) ⎪⎝ p1 ⎠ ⎪
⎩ ⎭ ⎩ ⎭
18. Ans. (d)
19. The air with enthalpy of 100kJ/kg is compressed by an air compressor to a pressure
and temperature at which its enthalpy becomes 200kJ/kg. The loss of heat is 40kJ/kg
m
from the compressor as· the air passes through it. Neglecting kinetic and potential
energies, the power required for an air mass flow of 0.5kg/s is [IES-2000]
(a) 30kW (b) 50kW (c) 70 kW (d) 90 kW
19. Ans. (a)
co
20. A two-stage compressor takes in air at 1.1 bar and discharges at 20 bar. For
maximum efficiency, the intermediate pressure is [IES-2000]
(a) 10.55 bars (b) 7.33 bars (c) 5.5 bar (d) 4.7 bar
.
20. Ans. (d)
tas
21. The discharge pressure of the compressor in the refrigeration system goes up due to
the
(a) lower volumetric efficiency of the compressor
(b) formation of scale in the condenser
(c) large size of the condenser (d) undercharge of the refrigerant [IES-2000]
lda
21. Ans. (b)
22. A 3-stage reciprocating compressor has suction pressure of 1 bar and delivery
pressure of 27 bar. For minimum work of compression, the delivery pressure of 1st stage
is [IES-1999]
(a) 14 bar (b) 9 bar (c) 5.196 bar (d) 3bar
vi
22. Ans. (d) For minimum work of compression in 3 stage compressor the delivery
pressure of 1st stage is 3 27/1=3bar = 3 bar
Ci
23. Which one of the following statements is true? [IES-1998]

(a) In a multi-stage compressor, adiabatic efficiency is less than stage efficiency
(b) In a multi-stage turbine, adiabatic efficiency is less than the stage efficiency
(c) Preheat factor for a multi-stage compressor is greater than one
w.
(d) Preheat factor does not affect the multi-stage compressor performance
23. Ans. (c)
ww
24. The heat rejection by a reciprocating

air compressor during the reversible
compression process AB, shown in the
following temperature-entropy diagram,
is represented by the area:
(a) ABC (b) ABDE
(c) ABFG (d) ABFOE
m
co
[IES-1997]
24. Ans. (b) Heat rejection during AB is given by area below it on entropy axis, i.e.
ABDE. DES
.
25. For a multistage compressor, the polytropic efficiency is [IES-1996]
(a) the efficiency of all stages combined together
tas (b) the efficiency of one stage.
(c) constant throughout for all the stages (d) a direct consequence of the
pressure ratio.
25. Ans. (a) For multistage compressor, the polytropic efficiency is the efficiency of all
stages combined together
lda
26. Phenomenon of choking in compressor means [IES-1996]
(a) no flow of air.
(b) fixed mass flow rate regardless of pressure ratio.
(c) reducing mass flow rate with increase in pressure ratio.
(d) increased inclination of chord with air stream.
26. Ans. (b) Phenomenon of choking in compressor means fixed mass flow rate
vi
regardless of pressure ratio
27. The usual assumption in elementary compressor cascade theory is that [IES-1996]
Ci
(a) axial velocity through the cascade changes.

(b) for elementary compressor cascade theory, the pressure rise across the cascade is
given by equation of state
(c) axial velocity through the cascade does not change.
(d) with no change in axial velocity between inlet and outlet, the velocity diagram is
w.
formed.
27. Ans. (c) The usual assumption in elementary compressor cascade theory is that
axial velocity thr6ugh the cascade does not change.
28. In a reciprocating air compressor the compression works per kg of air.

ww
[IES-1995]
(a) increases as clearance volume increases
(b) decreases as clearance volume increases
(c) is independent of clearance volume
(d) increases with clearance volume only for multistage compressor.
28. Ans. (a) Compression work per kg. of air increases as clearance volume increases.
29. Assertion (A): The isothermal efficiency of a reciprocating compressor becomes

100% if perfect cooling of the fluid during compression is attained.
Reason (R): Work done in a reciprocating compressor is less if the process of

compression is isothermal rather than polytropic. [IES-1993]
29. Ans. (a) Both assertion and reason are correct and R provides correct explanation
for A.

1. Reciprocating compressors are best suited for high pressure and low volume
capacity.
2. The effect of clearance volume on power consumption is negligible for the same
m
volume of discharge
3. While the compressor is idling, the delivery valve is kept open by the control circuit.
4. Inter-cooling of air between the stages of compression helps to minimize losses.
co
Of these statements
(c) 2 and 4 are correct (d) 3 alone is correct
30. Ans. (b)
.
31. The inlet and exit velocity diagrams of a turbomachine rotor are shown in the given
tas
figure. The turbomachine is [IES-1993]
vi lda
(a) an axial compressor with backward curved blades

(b) a radial compressor with backward curved blades
(c) a radial compressor with forward curved blades
Ci
(d) an axial compressor with forward curved blades

31. Ans. (c) From inlet and outlet diagrams it will be seen the blade velocity u2 > u1 from
which it is clear that it is radial compressor. For axial compressor, u2 = u1. Further in
outlet velocity triangle, velocity Vr2 is in the direction of u2 which means blades are
w.
forward curved. In case of backward curved blades the direction of Vr2 will be opposite to
that of u2 i.e. angle between Vr2 & u2 will be acute.
32. For two stage compressor in which index of compression for low pressure stage is m
and for high pressure stage in n. The load shearing with perfect inter-cooling is
ww
expressed as: [IES-1992]

W1 m ( n − 1) W1 n ( n − 1) W1 n W1 m
(a) = (b) = (c ) = (d ) =
W2 n ( m − 1) W2 m ( m − 1) W2 m W2 n
32. Ans. (a)
33. p-v diagram has been obtained from a test on a reciprocating compressor. Which of
the following represents that diagram? [GATE-2005]
(a) (b)
m
(c) (d)
. co
33. Ans. (d) It is obtained from a test, so pout will be some less than compressor outlet
pressure for opening the delivery valve.
tas
34. A single-acting two-stage compressor with complete inter cooling delivers air at 16
bar. Assuming an intake state of 1 bar at 15°C, the pressure ratio per stage is
(a) 16 (b) 8 (c) 4 (d) 2 [GATE-2001]
lda
34. Ans. (c) Pressure ratio of each stage must be same
pi p 2 pi × p2 p2
rp = = = = = 16 = 4
p1 pi p1 × pi p1
35. Air (Cp = 1 kJ/kg, γ = 1.4) enters a compressor at a temperature of 27°C. The
vi
compressor pressure ratio is 4. Assuming an efficiency of 80%, the compressor work

required in kJ/kg is [GATE-1998]
(a)160 (b)172 (c)182 (d)225
Ci
γ −1 γ −1
⎡ ⎤ ⎡ ⎤
γ RT1 ⎢⎛ p2 ⎞ γ ⎛ p ⎞ γ ⎡ 1.4 −1 ⎤
35. Ans. (c) Wideal = ⎜ ⎟ − 1 = c p T1 ⎜ ⎟ − 1⎥ = 1× 300 ⎢ 4 1.4 − 1⎥ = 146kJ / kg
⎥ ⎢ 2
γ − 1 ⎢⎝ p1 ⎠ ⎥ ⎢ p ⎥
⎢⎣ ⎥⎦ ⎢⎣⎝ 1 ⎠ ⎥⎦ ⎣ ⎦
Wideal 146
w.
Wactual = = = 182kJ / kg
η 0.8
36. Consider a two stage reciprocating air compressor with a perfect intercooler
operating at the best intermediate pressure. Air enters the low pressure cylinder at 1bar,
ww
27°C and leaves the high pressure cylinder at 9 bar. Assume the index of compression
and expansion in each stage is 1.4 and that for air R = 286.7 J/kg K, the work done per
kg air in the high pressure cylinder is [GATE-1997]
(a) 111 kJ (b) 222 kJ (c) 37 kJ (d) 74 kJ
36. Ans. (a)
Pr essure ratio must be same

Pi P2 Pi × P2 P2 9
∴ rP = = = = = =3
P1 Pi P1 × Pi P1 1
Work done of each stage also same
γ −1
γ RT1 ⎡ ⎤ 1.4 × 287 × 300 ⎡ 1.4 −1 ⎤
⎢γ
γ
Weach stage = − 1⎥ = 3 1.4 − 1⎥ = 111 kJ
γ − 1 ⎢⎣ P ⎥⎦ (1.4 − 1) ⎢⎣ ⎦
m
37. For an air-conditioning plant above 300 ton, which one of the following systems
would normally be preferred?
(a) Ammonia reciprocating compressor (b) Centrifugal chiller [IES-1997]
(c) Absorption refrigeration system (d) Hermetic compressor
co
37. Ans. (a) Ammonia reciprocating compressor is preferred
38. When the discharge pressure is too high in a refrigeration system, high pressure
control is installed to [IES-1996]
.
(a) stop the cooling fan (b) stop the water circulating pump.
tas
(c) regulate the flow of cooling water (d) stop the compressor.
38. Ans. (c) When the discharge pressure is too high in refrigeration system, high
pressure control is installed to regulate the flow of cooling water
39. What is the cause of burn out of hermetically sealed refrigerant compressors?
(a) Phase to phase short because of worn insulation
lda
(b) By prolonged overload operation
(c) By some mechanical failure (d) All the above [IAS-2007]
39. Ans. (d)
40. Which of the following are the special features of a hermetically sealed compressor
vi
of a refrigerator? [IAS-1999]
1. The compressor may be reciprocating to rotary type
2. No shaft seal is necessary
3. More silent in operation
Ci
4. COP is more than that of open compressor

Select the correct answer using the codes given below:
40. Ans. (b)
w.
41. Use of hermetically sealed compressor in a vapour compression refrigeration system

results in [IAS-1998]
(a) decrease in energy consumption (b) increase in energy consumption
(c) increase in COP (d) increase in pressure ratio
ww
41. Ans. (a)
42. When does L.P. cut-off occur in a refrigeration system?

(a) If the ambient temperature is low [IAS-2004]
(b) If non-condensable gases are present in the condenser
(c) If refrigerant charge is low
(d) If lubricating oil gets accumulated in the condenser
42. Ans. (a)
43. A refrigeration compressor designed to operate with R 22………. (can/cannot) be

operated with R 12 because the condensing pressure of R22 at any give temperature
is……..(higher/lower) than that of R 12. [GATE-1992]
43. Ans. cannot; higher
44. Select statements from List II matching the processes in List I. Enter your answer as
A, B if the correct choice for (1) is (A) and that for (2) is (B) [GATE-1999]
List I List II
(1) Inter-cooling (A) No heat transfer during compression
m
(2) Isothermal compression (B) Reduces low pressure compressor work
(C) Heat rejection during compression
(D) Reduces high pressure compressor work
co
44. Ans. (c, d)
45. The optimum intermediate pressure Pi for a gas turbine plant operating between
pressure limits P1 and P2 with perfect inter cooling between the two stages of
.
compression (with identical isentropic efficiency is given by [IES-2003,IES-1996]
tas
1
(a) Pi= P2-P1 (b) Pi= (P1+P2) (c) Pi= P1 P2 (d) Pi= P22 − P12
2
45. Ans. (c): We know that for minimum compressor work pressure ratio of both stage
lda
P1 P
must be same so = i or Pi= P1 P2
Pi P2
46. For a two stage-reciprocating compressor, compression from P1 to P2 is with perfect
inter-cooling and no Pressure losses. If compression in both cylinders follows the
vi
same poly-tropic process and the atmospheric pressure is Pa , then the intermediate
pressure Pi is given by [IES-1994]
1
Ci
(a) Pi= P2-P1 (b) Pi= (P1+P2) (c) Pi= P1 P2 (d) Pi= P22 − P12
2
46. Ans. (c): We know that for minimum compressor work pressure ratio of both stages
w.
P1 P
must be same so = i or Pi= P1 P2 Note: Here Pa is superfluous data that has
Pi P2
no use.
47. Two-stage compressors takes in air at 1.1 bar and discharges at 20 bar. For
ww
maximum efficiency, the intermediate pressure is [IES-2000]

(a) 10.55 bar (b) 7.33 bar (c) 5.5 bar (d) 4.7 bar
47. Ans. (d): We know that for minimum compressor work pressure ratio of both stages
must
P1 P
be same so = i or Pi= P1 P2 = 1.1 x 20 = √22 = 4.7 bar
Pi P2
48. 3-stage reciprocating compressors have suction pressure of 1 bar and delivery
pressure of 27 bar. For minimum work of compression, the delivery pressure of first
stage is
(a) 14 bar (b) 9 bar (c) 5.196 bar (d) 3 bar [IES-1999]
m
48. Ans. (d): We know that for minimum compressor work pressure ratio of 3-stage must
be same so P =Pi1 i2 = P2 = 3 P P P =3 P
i1 i2 2 2
co
P P 1 i1 P i2
P P P1 P i1 i2 1
or Pi1= P1x 3 P = P12/3 .P21/3= 1x 271/3=3 bar

2
P 1
.
49. In a gas turbine cycle with two stages of reheating, working between maximum
(a) (P1P4) 1/3 and (P1P4) 2/3

tas
pressure P1 and minimum pressure P4, the optimum pressures would be
(b) (P12 P4) 1/3 and (P1P42) 1/3
(c) (P1P4) 1/2 and P1P42/3 (d) (P1P4) 1/2 and (P1P4) 2/3 [IES-1993]
lda
49. Ans. (b) We know that for minimum compressor work pressure ratio of 3-stage must
be same so P2 = P3 = P4 = 3 P P P = 3 P4
2 3 4
P1 P 2 P 3
P P P1 P1 2 3
or P2= P1x3 P = (P12 P4)1/3 =(P1P42)1/3

vi
4
and P3= P 4
P 1
3 P 4
P 1
Ci
Alternatively you may give answer by dimensional similarity. Only choice (b) has the
dimension of pressure.
w.
50. Four-stage compressor with perfect inter-cooling between stages compresses air
from 1 bar to 16 bar. The optimum pressure in the last intercooler will be
(a) 6 bar (b) 8 bar (c) 10 bar (d) 12 bar [IES-1998]
ww
50. Ans. (b): We know that for minimum compressor work pressure ratio of 4-stage must
be same so P i1 = P i2 = P i3 = P 2 = 4 Pi1 Pi 2 Pi 3 P2 =4 P
2
P 1 P i1 P i2 P i3
P P P1 i1 i2 P i3 P
1
or Pi3 = P2 = P1 1/4P2 ¾ =11/4x(16) ¾ = 8 bar

P2
4
P1
Volumetric Efficiency of reciprocating Compressors

51. Which one of the following statements is correct for reciprocating air compressor?
(a) Its volumetric efficiency increases with increasing clearance ratio
(b) Its volumetric efficiency increases with increasing pressure ratio
(c) Its volumetric efficiency does not vary with change in clearance ratio and pressure
ratio
(d) Its volumetric efficiency decreases with increasing clearance ratio and pressure ratio,
both [IES 2007]
m
1
⎛ p ⎞n
51. Ans. (d) ηv = 1 + C – C. ⎜⎜ 2 ⎟⎟
⎝ p1 ⎠
co
Volumetric efficiency of a reciprocating air compressor increases with
1. increase in clearance ratio
2. decrease in delivery pressure
.
3. multi staging tas
Which of the statements given above is/are correct?
(a) Only 1 and 2 (b) Only 2 and 3 (c) Only 3 (d) 1, 2 and 3
1
⎛ p2 ⎞ n
52. Ans. (b) ηv = 1 + C − C ⎜ ⎟ if p2 ↓ thenηv ↑
⎝ p1 ⎠
lda
53. The clearance volume of a reciprocating compressor directly affects
(a) piston speed (b) noise level [IAS-1998]
(c) volumetric efficiency (d) temperature of air after compression
1/n
⎛P ⎞
53. Ans. (c) ηv = 1 + c − c ⎜ 2 ⎟
vi
⎝ P1 ⎠
54. Which of the following statements are correct for multi staging in a reciprocating air
compressor? [IES-2006]
1. It decreases the volumetric efficiency.
Ci
2. The work done can be reduced.

3. A small high-pressure cylinder is required.
4. The size of flywheel is reduced.
Select the correct answer using the codes given below
w.
(a) 1, 2 and 3 (b) 2, 3 and 4 (c) 1, 3 and 4 (d) 1, 2 and 4

54. Ans. (b) 1 is false, It increases the volumetric efficiency.
55. Consider the following statements [IES-2000]

The volumetric efficiency of a reciprocating compressor can be enhanced by
ww
1. heating the intake air 2. decreasing the clearance volume

3. cooling the intake air
Which of these statements is/are correct?
(a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 3 alone
55. Ans. (c)
56. Assertion (A): Decrease of pressure and increase of temperature of the refrigerant in
the suction pipeline connecting the evaporator to the reciprocating compressor reduces
the refrigerating capacity of the system. [IES-2003]
Reason (R): Decrease of pressure and increase of temperature of the refrigerant in the
suction pipeline connecting the evaporator to the compressor reduces the volumetric
efficiency of the reciprocating compressor.
56. Ans. (a)
57. The ratio of the clearance volume to the displacement volume of a R12 reciprocating
m
compressor is 0.05. Specific volume at inlet and outlet of compressor are 0.04 and 0.02
m3/kg respectively. Volumetric efficiency of the compressor is [IES-2002]
(a) 95.0% (b) 47.5% (c) 38.0% (d) 19.0%
co
57. Ans. (a)

The volumetric efficiency of a compressor depends upon
1. clearance volume 2. pressure ratio 3. index of expansion.
.
Of these correct statements are tas
(a) 1 and 2 (b) 1 and 3 (c) 2 and 3 (d) 1, 2, and 3
58. Ans. (d) The volumetric efficiency of a compressor depends upon 1. clearance
volume 2. pressure ratio. 3. index of expansion.
59. A gas engine has a swept volume of 300 cc and clearance volume of 25 cc. Its
lda
volumetric efficiency is 0.88 and mechanical efficiency is 0.90. What is the volume of the
mixture taken in per stroke? [IES-1995]
(a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc
Volume of mixture
59. Ans. (c) Volumetric η = , and volume of mixture = 300 x 0.88 =
300
264 cc
vi
60. Which of the following statements does NOT apply to the volumetric efficiency of a
reciprocating air compressor? [GATE-1999]
Ci
(a) It decreases with increase in inlet temperature

(b) It increases with decrease in pressure ratio
(c) It increases with decrease in clearance ratio
(d) It decreases with increase in clearance to stroke ratio
60. Ans. (a)
w.
61. Which of the following are the reasons for the volumetric efficiency of reciprocating
compressor being less than 100%? [IAS-1995]
1. Deviations from isentropic process. 2. Pressure drop across the valves.
3. Superheating in compressor. 4. Clearance volume.
ww
5. Deviations from isothermal process 6. leakages.

Select the correct answer from the codes given below:
(a) 1, 2, 3 and 5 (b) 2, 3, 4 and 5 (c) 1, 4, 5 and 6 (d) 2, 3 and 6
61. Ans. (d) The reason for volumetric efficiency of reciprocating compressor being less
that 100% are pressure drop across the valves, superheating in compressor, clearance
volume and leakages.
Effect of Clearance on Work

In a reciprocating compressor, clearance volume is provided.
1. so that piston does not hit and damage the valves
m
2 to account for differential thermal expansion of piston and cylinder
3. to account for machining tolerances
4. to achieve isentropic compression
co
62. Ans. (a) In centrifugal compressor there also isentropic compression occurs so.
63. A large clearance volume in a reciprocating compressor results in [IES-1995]
.
(a) reduced volume flow rate (b) increased volume flow rate
(c) lower suction pressure tas(d) lower delivery pressure.
63. Ans. (d) Large clearance volume in reciprocating compressor results in lower
delivery pressure.
64. Clearance volume of a reciprocating compressor is 100 ml, and the volume of the
cylinder at bottom dead centre is 1.0 litre. The clearance ratio of the compressor is
lda
[GATE-1997]
64. Ans. (c) Piston displacement volume = 900 ml
clerance volume 100 1
Therefore clearance ratio = = =
Piston displacement volume 900 9
vi
65. A R-12 refrigerant reciprocating

compressor operates between the
Ci
condensing temperature of 30oC and

evaporator temperature of – 20oC.
The clearance volume ratio of the
compressor is 0.03. Specific heat ratio
of the vapour is 1.15 and the specific
w.
volume at the suction is 0.1089 m3/kg.

Other properties at various states are
given in the figure. To realize 2 Tons
of refrigeration, the actual volume
ww
displacement rate considering the

effect of clearance is [GATE-2004]
(a) 6.35x10-3 m3/s (b) 63.5 x10-3 m3/s (c) 635 x10-3 m3/s (d) 4.88x10-3 m3/s
65. Ans. (a)
m
. co
Performance Characteristics of Reciprocating Compressors
tas
66. Which of the following techniques are employed for control of reciprocating
compressors?
1. Throttle control 2. Clearance control 3. Blowing air to waste
(a) 1, 2 and 3 (b) 1 and 2 only
lda
(c) 2 and 3 only (d) 1 and 3 only [IES 2007]
66. Ans. (d)
67. Reciprocating compressors are provided with [IES-2000]

(a) simple disc/plate valve (b) poppet valve
(c) spring-loaded disc valve (d) solenoid valve
vi
67. Ans. (a)
68. Consider the following factors: [IES-1999]

1. Cylinder size 2. Clearance ratio
Ci
3. Delivery pressure 4. Compressor shaft power.

The factors which affect the volumetric efficiency of a single-stage reciprocating air
compressor would include
w.
68. Ans. (a) Volumetric efficiency of a single stage reciprocating air compressor is
dependent on clearance ratio and cylinder size.
ww
69. The diagram shown in the figure

represents reversible compression of air
on the p-V co-ordinates. The work of
compression needed by a centrifugal
compressor is equal to the area
(a) ABDE-ABC
(b) ABDE
(c) ABFG
(d) ABFG-ABC
m
co
[IES-1999]
69. Ans. (b) Work of compression is area below the compression curve AB, i.e. ABDE
70. Performance of a reciprocating compressor is expressed by [IAS-2003]
.
Isothermal work Indicated work
tas Adiabatic work Indicated work
(a) (b) (c) (d)
Indicated work Isothermal work Indicated work Adiabatic work
70. Ans. (a)
71. The isothermal efficiency of a reciprocating compressor is defined as actual work

done during compression
lda
[IAS 1994]
actual work done during compression
(a)
isothermal work done during compression
adiabatic work done during compression
(b)
vi

(c)
actual work done during compression
Ci
(d)
actual work done during adiabatic compression
71. Ans. (c)
w.
Rotary Compressors
72. A rotary compressor is used when a refrigerating system has to handle a refrigerant
with
(a) low specific volume and high pressure difference
ww
(b) low specific volume and low pressure difference

(c) large specific volume and high pressure difference
(d) large specific volume and low pressure difference [IAS-1997]
72. Ans. (d)
73. Assertion (A): A vane type rotary compressor is a rotodynamic machine.

Reason(R): A rotodynamic machine is one in which a fluid flows freely through the
rotating part of the machine. [IES-2005]
73. Ans. (a)
74. The inlet and exit velocity diagrams of a turbo-machine rotor are shown.
This turbo-machine is [IES-2002]
m
co
(a) an axial compressor with backward curved blades
.
(b) a radial compressor with backward curved blades
tas
(d) an axial compressor with forward curved blades
74. Ans. (c)
lda
Screw Compressors
Centrifugal Compressors
75. In the centrifugal air compressor design practice, the value of polytropic exponent of
compression is generally taken as [IES-1998]
(a) 1.2 (b) 1.3 (c) 1.4 (d) 1.5
vi
75. Ans. (c)
76. What does application of centrifugal air compressors lead to?

Ci
(a) Large frontal area of aircraft

(b) Higher flow rate through the engine
(c) Higher aircraft speed
(d) Lower frontal area of the aircraft [IES-2006]
76. Ans. (a)
w.
77. In a centrifugal compressor, how can the pressure ratio be increased?

(a) Only by increasing the tip speed [IES-2006]
(b) Only by decreasing the inlet temperature
(c) By both (a) and (b)
ww
(d) Only by increasing the inlet temperature

78. Ans. (c)
79. The pressure rise in the impeller of centrifugal compressor is achieved by

(a) the decrease in volume and diffusion action [IES-2002]
(b) the centrifugal action and decrease in volume
(c) the centrifugal and diffusion action
(d) the centrifugal and push-pull action
79. Ans. (c)
80. The flow in the vane less space between the impeller exit and diffuser inlet of a
centrifugal compressor can be assumed as [IES-2001]
(a) free vortex (b) forced vortex (c) solid body rotation (d) logarithmic spiral
80. Ans. (b)
81. Consider the following statements [IES-2000]

In centrifugal compressors, there is a tendency of increasing surge when
m
I. the number of diffuser vanes is less than the number of impeller vanes
2. the number of diffuser vanes is greater than the number of impeller vanes
3. the number of diffuser vanes is equal 10 the number of impeller vanes
co
4. mass flow is greatly in excess of that corresponding to the design mass flow
(a) 1 and 4 (b) 2 alone (c) 3 and 4 (d) 2 and 4
81. Ans. (d)
.
82. In a radial blade centrifugal compressor, the velocity of blade tip is 400 m/s and slip
tas
factor is 0.9. Assuming the absolute velocity at inlet to be axial, what is the work done
per kg of flow? [IES-2005]
(a) 36 kJ (b) 72 kJ (c) 144kJ (d) 360 kJ
82. Ans. (c)
lda
83. In centrifugal compressor terminology, vane less space refers to the space between
(a) the inlet and blade inlet edge (b) blades in the impeller [IES-1999]
(c) diffuser exit and volute casing (d) impeller tip and diffuser inlet edge
83. Ans. (d) The vane less shape' refers to space between impeller tip and diffuser inlet
edge.
vi
84. Centrifugal compressors are suitable for large discharge and wider mass flow range,
but at a relatively low discharge pressure of the order of 10 bars, because of [IES-1997]
(a) low pressure ratio (b) limitation of size of receiver
(c) large speeds (d) high compression index
Ci
84. Ans. (a) Pressure ratio is low for centrifugal compressors
85. Given: Vw2 = velocity of whirl at outlet [IES-1997]

u2 = peripheral velocity of the blade tips
w.
the degree of reaction in a centrifugal compressor is equal to

Vw 2 u2 2Vw 2 Vw 2
(a )1 − (b)1 − (c)1 − ( d )1 −
2u2 2Vw 2 u2 u2
85. Ans. (a)
ww
86. For large tonnage (more than 200 tons) air-conditioning applications, which one of
the following types of compressors is recommended? [IES-1996]
(a) Reciprocating (b) Rotating (c) Centrifugal (d) Screw.
86. Ans. (d) For large tonnage air conditioning applications, specially built centrifugal
compressors are used
87. In a centrifugal compressor assuming the same overall dimensions, blade inlet angle
and rotational speeds, which of the following bladings will given the maximum pressure
rise?
(a) Forward curved blades (b) Backward curved blades. [IES-1995]
(c) Radial blades (d) All three types of bladings have the same pressure rise.
87. Ans. (a) Forward curved blades give maximum pressure rise.
88. In a centrifugal compressor, the highest Mach number leading to shockwave in the
fluid flow occurs at
m
[IES-1995]
(a) diffuser inlet radius (b) diffuser outlet radius
(c) impeller inlet radius (d) impeller outer radius.
88. Ans. (b)
co
89. If two geometrically similar impellers of a centrifugal compressor are operated at the
same speed, then their head, discharge and power will vary with their diameter ratio 'd'
as
(a) d, d2 and d3 respectively (b) d2, d3 and d5 respectively.
.
3 5
(c) d, d and d respectively tas (d) d2, d and d3 respectively.
89. Ans. (d) Head, discharge and power are proportional to d2, d and d3 [IES-1994]
90. The stagnation pressure rise in a centrifugal compressor stage takes place.
(a) only in the diffuser (b) in the diffuser and impeller. [IES-1994]
(c) only in the impeller (d) only in the inlet guide vanes.
lda
90. Ans. (a)
91. The specific speed of a centrifugal compressor is generally [GATE-1997]

(a) higher than that of an axial compressor
(b) less than that of a reciprocating compressor
(c) independent of the type of compressor, but depends only on the size of the
vi
compressor
(d) more than the specific speed of the reciprocating compressor but less that of the
axial compressor
91. Ans. (d)
Ci
92. A multistage compressor is to be designed for a given flow rate and pressure ratio. If
the compressor consists of axial flow stages followed by centrifugal instead of only axial
flow stages, then the [IES-1993]
w.
(a) overall diameter would be decreased (b) overall diameter would be increased
(c) axial length of the compressor would be increased
(d) axial length of the compressor would be decreased
92. Ans. (b) In case of axial flow stages, diameter will be less and same but in case of
centrifugal compressor, the flow is radial at outlet and thus overall diameter will increase.
ww
93. When the outlet angle from the rotor of a centrifugal compressor is more than 90,
then the blades are said to be [IES-1992]
(a) forward curved (b) backward curved
(c) radial (d) either backward or forward curved
93. Ans. (a)
Performance Characteristics of Centrifugal Compressors
94. Which one of the following expresses

the isentropic efficiency ɳ of the
compression process in terms of
enthalpy changes as indicated in the
figure given above?
ΔH s ΔH
(a) η = (b)η =
m
ΔH ΔH s
( ΔH − Δ H s )
(c) η =
ΔH
co
(ΔH − ΔH s )
(d) η = [IES-2005]
ΔH s
94. Ans. (a)
.
tas
95. Which portion of the centrifugal
compressor characteristics shown in
the figure is difficult to obtain
experimentally?
(a) RS
lda
(b) ST
(c) TU
(d) UV
vi
Ci
[IES-2001]
95. Ans. (a)
96. For centrifugal compressors, which one of the following is the correct relationship
between pressure coefficient (ɸp) slip factor (ɸs) work input factor (ɸw) and isentropic
w.
efficiency (ɳa)? [IES-2005]

φs × φw φw φs × η a
(a) φ p = (b) φ p = (c) φ p = φs × φw ×η a (d) φ p =
ηa φs × η a φw
ww
96. Ans. (c)
97. Which one of the following is the effect of blade shape on performance of a
centrifugal compressor? [IES-1996]
(a) Backward curved blade has poor efficiency.
(b) Forward curved blade has higher efficiency.
(c) Backward curved blades lead to stable performance.
(d) Forward curved blades produce lower pressure ratio
97. Ans. (c) In centrifugal compressor, backward curved blades lead to stable
performance.
98. The curve in the given figure shows

the variation of theoretical pressure ratio
with mass of flow rate for a compressor
running at a constant speed. The
permissible operating range of the
compressor is represented by the part
m
of the curve from
(a) A to B (b) B to C
(c) B to D (d) D to E
co
[IES-1995]
98. Ans. (c) Curve B to D represents permissible operating range of compressor.
.
99. Air ( Cp = 1 KJ, γ = 1.4 ) enters a compressor at a temperature of 270C, the
tas
compressor pressure ratio is 4. Assuming an efficiency of 80 %, the compressor work
required in KJ/Kg is [GATE-1998]
(a) 160 (b) 172 (c) 182 (d) 225
lda
γ γ (γ−1)
99. Ans. (c): Wideal = (P1V1 – P2V2) = P1V1 [ ⎛⎜P2⎞⎟ γ - 1]
γ −1 γ −1 ⎜ ⎟
⎝ P1 ⎠
γ (γ−1) (γ−1)
= RT1 [ ⎛⎜P2⎞⎟ γ - 1] = CpT1 [ ⎛⎜P2⎞⎟ γ - 1] = 1x300[40.4/1.4-1] = 146
γ −1 ⎜ ⎟
⎝ P1 ⎠
⎜ ⎟
⎝ P1 ⎠
vi
146
∴ Wactual = W ideal = = 182
η 0.8
Ci
Comparison of Performance of Reciprocating and Centrifugal

w.
Axial flow compressor

100. In an axial flow compressor, when the degree of reaction is 50%, it implies that
(a) Work done in compression will be the least [IES-2006]
(b) 50% stages of the compressor will be ineffective
ww
(c) Pressure after compression will be optimum

(d) The compressor will have symmetrical blades
100. Ans. (d)

For a large aviation gas turbine an axial flow compressor is usually preferred over
centrifugal compressor because
1. the maximum efficiency is higher. 2. the frontal area is lower.
3. the pressure rise per stage is more. 4. the cost is lower.

(a) 1 and 4 (b) Only 1 and 2 (c) 1,2 and 3 (d) 2,3 and 4
101. Ans. (b)
102. While flowing through the rotor blades in an axial flow air compressor, the relative
velocity of air: [IES-2005]
(a) Continuously decreases (b) Continuously increases
(c) First increases and then decreases (d) First decreases and then increases
m
102. Ans. (a)
103. Which one of the following is the correct expression for the degree of reaction for
co
an axial-flow air compressor? [IES-2004]
Work input to the rotor Change of enthalpy in the rotor
(a) (b)
Work input to the stage Change of enthalpy in the stage
Pressure rise in the rotor Isentropic work
.
(c) (d)
Pressure rise in the stage tas Actual work
103. Ans. (c) It is compressor.
104. If the static temperature rise in the rotor and stator respectively are ∆TA and ∆TB,
the degree of reaction in an axial flow compressor is given by [IES-1999]
ΔTA ΔTA ΔTB ΔTB
lda
(a) (b) (c) (d)
ΔTB ΔTA +ΔTB ΔTA +ΔTB ΔTA
104. Ans. (b)
static temperature rise in rotor ΔTA
Degreeof reaction of axial flow compressor = =
static temperature rise in stage ΔTA +ΔTB
vi
105. Degree of reaction in an axial compressor is defined as the ratio of static enthalpy
rise in the [IES-1996]
(a) rotor to static enthalpy rise in the stator. (b) stator to static enthalpy rise in the rotor.
Ci
(c) rotor to static enthalpy rise in the stage. (d) stator to static enthalpy rise in the stage.
105. Ans. (c) Degree of reaction in an axial compressor is defined as the ratio of static
enthalpy rise in the rotor to static enthalpy rise in the stage.
106. Compared to axial compressors centrifugal compressors are more suitable for
w.
(a) high head, low flow rate (b) low head, low flow rate [IES-2002]
(c) low head, high flow rate (d) high head, high flow rate
106. Ans. (c)
ww
107. Stalling of blades in axial- flow compressor is the phenomenon of [IES-2002]

(a) air stream blocking the passage (b) motion of air at sonic velocity
(c) unsteady, periodic and reversed flow
(d) air steam not able to follow the blade contour
107. Ans. (d) Same Q IES 2007 Q105
108. In an axial flow compressor [IES-2002]

α1 =exit angle from stator β1 = inlet angle to rotor
α2 = inlet angle to stator β2 = outlet angle from rotor
The condition to have a 50% degree of reaction is

(a) α1 = β2 (b) α2 = β1 (c) α1 = β2 and β1 = α2 (d) α1 = α2 and β1 = β2
108. Ans. (c)
109. In an axial flow compressor design, velocity diagrams are constructed from the
experimental data of aerofoil cascades. Which one of the following statements in this
regard is correct? [IES-2000]
(a) Incidence angle of the approaching air is measured from the trailing edge of the
blade
m
(b) δ is the deviation angle between the angle of incidence and tangent to the camber
line.
(c) The deflection ε of the gas stream while passing through the cascade is given by
co
ε = α1 − α 2
(d) ε is the sum of the angle of incidence and camber less any deviation angle, i.e.,
ε = i +θ −δ
109. Ans. (a)
.
(c) an axial compressor
tas
110. The turbo machine used to circulate refrigerant in a large refrigeration plant is
(a) a centrifugal compressor (b) a radial turbine
(d) an axial turbine
[IES-1998]
110. Ans. (c)
111. The energy transfer process is [IES-1998]

lda
(a) continuous in a reciprocating compressor and intermittent in an axial compressor
(b) continuous in an axial compressor and intermittent in a reciprocating compressor
(c) continuous in both reciprocating and axial compressors
(d) intermittent in both reciprocating and axial compressors
111. Ans. (c)
vi
112. In an axial flow compressor stage, air enters and leaves the stage axially. If the
whirl component of the air leaving the rotor is half the mean peripheral velocity of the
rotor blades, then the degree of reaction will be [IES-1998]
Ci
(a) 1.00 (b) 0.75 (c)0.50 (d)0.25

Vf Vf 1
112. Ans. (d) Degree of reaction = ( tan β1 + tan β 2 ) ; =
2Vb Vb 2
Vf 1 1
(1) = 0.25
w.
tan β1 = = = tan β 2 ∴Degree of reaction =

Vb 2 2× 2
113. If an axial flow compressor is designed for a constant velocity through all stages,
then the area of annulus of the succeeding stages will [IES-1998]
ww
(a) remain the same (b) progressively decrease

(c) progressively increase (d) depend upon the number of stages
113. Ans. (a)
114. The inlet and exit velocity diagrams of a turbo-machine rotor are shown in the figure
I and figure II respectively. [IES-1995]
The turbo-machine is
m
(a) an axial compressor with radial blades
(b) a radial compressor with radial blades.
(d) an axial compressor with forward curved blades.
co
114. Ans. (a) Velocity diagrams are for axial compressor (u1 = u2) with radial blades (V1
and Vr2) are perpendicular to u1 and u2).
115. In a multi-stage axial flow compressor with equal temperature rise in all stages, the
.
Pressure ratio in the subsequent stages
(a) Remains constant
(c) Decreases
115. Ans. (a)
tas
(b) Increases gradually
(d) Increases rapidly [IES 2007]
116. Consider the following statements in respect of axial flow compressor:

1. An axial flow air compressor is often describe is a reversed reaction turbine.
lda
2. With 50% degree of reaction, the velocity diagrams are symmetrical.
Which of the statements given above is/are correct? [IES 2007]
(a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2
116. Ans. (c)
117. Stalling phenomena in an axial flow compressor stage is caused due to which one
vi
of the following?
(a) Higher mass flow rate than the designed value
(b) Lower mass flow rate than the designed value
Ci
(c) Higher mass flow rate or non-uniformity in the blade profile

(d) Lower mass flow rate or non-uniformity in the blade profile [IES 2007]
117. Ans. (d)
118. Consider the following statements regarding the axial flow in an air compressor:
w.
1. Surging is a local phenomenon while stalling affects the entire compressor.

2. Stalling is a local phenomenon while surging affects the entire compressor.
3. The pressure ratio of an axial compressor stage is smaller than that of a centrifugal
compressor stage.
ww
Of these statements are correct [IES-2001]

(a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3
118. Ans. (d)
119. High positive incidence in an axial compressor blade row leads to

(a) suppression of separation of flow on the blade. (b) choking of the flow.
(c) separation of flow on the suction side of the blade. [IES-1994]
(d separation of flow on the pressure side of the blade.
119. (a)
120. Assertion (A): In axial flow compressors, momentum blading is more efficient than
radial flow blading. [IES-1997]
Reason (R): In radial flow blading, the pressure head increases due to centrifugal head.
120. Ans. (b)
121. Assertion (A): The work required per kg of air flow / min. for axial flow compressors
is lower than that for centrifugal compressor for the same pressure ratio. [IES-1995]
m
Reason (R): The isentropic efficiency of axial flow compressor is much higher than that
of a centrifugal compressor.
121. Ans. (a) Both A and R are correct and R provides right explanation for A.
co
121. In air-craft gas turbines, the axial flow compressor is preferred because [IES-1993]
(a) of high pressure rise (b) it is stall free (c) of low frontal area (d) of higher thrust
121. Ans. (c) Axial flow compressor is preferred in aircraft gas turbines because of
requirement of low frontal area.
.
(a) blade camber
tas
122. In axial flow compressor, exit flow angle deviation from the blade angle is a function
of
(b) space-chord ratio [IES-1993]
(c) both blade camber and space-chord ratio (d) blade camber and incidence angle
122. Ans. (c)
lda
123. Match List-I with List-II (pertaining to blower performance) and select the correct
answer using the codes given below the Lists: [IES-1997]
List-I List-Il
A. Slip 1. Reduction of whirl velocity
B. Stall 2. Fixed mass flow rate regardless of pressure ratio
vi
C. Choking 3. Flow separation

4. Flow area reduction
Codes: A B C A B C
(a) 4 3 2 (b) 4 1 3
Ci
(c) 1 3 2 (d) 2 3 4
123. Ans. (c)
124. Under which one of the following sets of conditions will a supersonic compressor
w.
have the highest efficiency? [IES-1995]

(a) Rotor inlet velocity is supersonic and exit velocity subsonic; stator inlet velocity is
subsonic and exit velocity is subsonic.
(b) Rotor inlet velocity is supersonic and exit velocity subsonic; stator inlet velocity is
supersonic and exit velocity is subsonic.
ww
(c) Rotor inlet velocity is supersonic and exit velocity supersonic; stator inlet velocity is
supersonic and exit velocity is subsonic.
(d) Rotor inlet velocity is supersonic and exit velocity supersonic; stator inlet velocity is
subsonic and exit velocity is subsonic.
124. Ans. (c)
125. Consider the following characteristics: [IAS-2002]

1. The fluid enters the pump axially and is discharged radially.
2. Maximum efficiency may be of the order of 90%.
3. Development of a low head

4. A limited suction capacity
Which of the above characteristics are possessed by axial flow pumps?
125. Ans. (b) In Axial flow pumps the fluid both enters and discharged axially.
m
Flash Chamber
126. The flash chamber in a single stage simple vapour compression cycle [IES-1998]
(a) increases the refrigerating effect (b) decreases the refrigerating effect
(c) increases the work of compression (d) has no effect on refrigerating effect
co
126. Ans. (d) Flash chamber has no effect on refrigerating effect.
127. Flash chamber is used in refrigeration for which one of the following?
(a) Decreasing the pressure during multistage compression [IAS-2007]
.
(b) Increasing the compressor pressure ratio
(c) Effective intercooling medium for purpose of increasing COP
tas
(d) Maintaining the same pressure and temperature
127. Ans. (c)
128. Match List-I with List-II and select the correct answer using the codes given below
the Lists:
lda
List-I List-II
A. Bell Colemn refrigeration 1. Compressor [IES-1998]
B. Vapour compression refrigeration 2. Generator
C. Absorption refrigeration 3. Flash chamber
D. Jet refrigeration 4. Expansion cylinder
vi
(a) 1 4 3 2 (b) 4 1 3 2
(c) 1 4 2 3 (d) 4 1 2 3
128. Ans. (d)
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
5.
Condensers
m
co
Heat Rejection Ratio
1. In a vapour compressor refrigeration system, the compressor capacity is 2100
kJ/minute and heat rejection factor is 1.2. What will, respectively be the heat rejected
from the condenser and C. O. P? [IES-2004]
.
(a) 5040 kJ/minute and 5 (b) 2520 kJ/minute and 5
(c) 2520 kJ/minute and 4
1. Ans. (b)
refrigeration = = 1+
W
= 1+
tas
(d) 5040 kJ/minute and 4
Heat rejection ratio (G) = The loading on the condenser per unit of
Qo + W 1
Qo Qo COP
1 1
or G = 1 + or 1.2 = 1 + or COP = 5
lda
COP COP
given W = 210 kJ / min
∴ Qo = 2100 kJ / min or Qo + W = 1.2.Qo = 2520kJ / min
2. A refrigeration plant uses a condenser with heat rejection ratio of 1.2. If the capacity of
vi
the plant is 210kJ/min, then what is the value of the COP of the refrigeration plant?
(a) 3 (b) 5 (c) 7 (d) 9 [IES-2005]
Q1 Q2 1
2. Ans. (b) = 1.2 or = = 5 = COP
Q2 Q1 − Q2 0.2
Ci
3. Experimental measurements on a refrigeration system indicate that rate of heat

extraction by the evaporator, rate of heat rejection in the condenser and rate of heat
rejection by the compressor body to environment are 70 kW, 90 kW and 5 kW
w.
respectively. The power input (in kW) required to operate the system is [IES-2002]
(a) 15 (b) 20 (c) 25 (d) 75
3. Ans. (c)
ww
Types of Condensers
4. For small installations of refrigeration systems (up to 35 kW), which type of condenser
is used? [IES-2006]
(a) Shell and cube type (b) Shell and coil type
(c) Double tube type (d) Air cooled type
4. Ans. (d)
5. A condenser of a refrigeration system rejects heat at a rate of 120 kW, while its
compressor consumes a power of 30 kW. The coefficient of performance of the system
would be
(a) 1/4 (b) 1/3 (c) 3 (d) 4 [IES-1995]
5. Ans. (b) Heat rejected in condenser = 120 kW: Compressor work = 30 kW;
Net refrigeration effect = 120 - 30 = 90 kW.
Therefore COP = 30/90 = 1/3
6. A pressure gauge on the discharge side of a refrigerant compressor reads too high.
m
The reasons could be: [IES-1995]
1. Lack of cooling water 2. Water temperature being high
3. Dirty condenser surfaces 4. Refrigerant temperature being too high
co
Of these reasons
(a) 1, 2 and 4 are valid (a) 1, 2 and 3 are valid
(c) 2, 3 and 4 are valid (a) 1, 3 and 4 are valid
6. Ans. (b)
.
7. Assertion (A): Condensers of large refrigerating plants including central air-
tas
conditioning systems are invariably water-cooled. [IAS-1996]
Reason (R): Water is available at a temperature lower than that of the surrounding air
and has a higher specific heat.
7. Ans. (a)
lda
8. A condenser of refrigeration system rejects heat at a rate of 120 kW, while its
compressor consumes a power of 30 kW. The coefficient of performance of the system
would be [GATE-1992]
1 1
(a) (b) 4 (c) (d) 3
4 3
8. Ans. (d)
vi
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
6.
Expansion Devices
m
co
Types of Expansion Devices
1. Match List-I (Expansion device) with List-II (Operation) and select the correct answer
using the codes given below the lists: [IES-2001]
.
List-l (Expansion device) List-II (Operation)
A. Float valve
B. Automatic expansion
tas 1. Constant degree of superheat at evaporator exit
pressure
2. Constant degree of superheat at evaporator inlet
valve pressure
C. Internally equalized thermostatic 3. Constant level of refrigerant in the evaporator
lda
expansion valve
D. Externally equalized thermostatic 4. Constant pressure in the evaporator expansion
valve
Codes:
A B C D A B C D
(a) 1 2 4 3 (b) 3 2 4 1
vi
(c) 3 4 2 1 (d) 1 4 2 3
1. Ans. (c)
2. An expansion valve is NOT used for reducing pressure in the [IAS-2000]

Ci
(a) vapour compression refrigeration cycle (b) vapour absorption refrigeration cycle
(c) steam-jet refrigeration cycle (d) gas refrigeration cycle
2. Ans. (d) Steam-jet refrigeration cycle is similar to vapour compression refrigeration
cycle where mechanical compressor is substituted by steam ejector or booster.
w.
3. Assertion (A): In vapour compression refrigeration system throttle valve is used and
not expansion cylinder. [IES-1995]
Reason (R): Throttling is a constant enthalpy process.
3. Ans. (b) A and R are true. But R is not right reasoning for A.
ww
Automatic or Constant-Pressure Expansion Valve

4. Which one of the following types of expansion valves is suitable for a refrigeration
plant operating at constant load? [IAS-2007]
(a) Thermostatic expansion valve (b) Automatic expansion valve
(c) Capillary tube (d) none of the above
4. Ans. (b)
5. An automatic expansion value is required to maintain constant [IAS-1998]

(a) pressure in the evaporator (b) temperature in the freezer
(c) pressure in the liquid line (d) temperature in the condenser
5. Ans. (a)
Thermostatic-Expansion Valve
6. The sensing bulb of the thermostatic expansion valve is located at the [IES-2002]
m
(a) exit of the evaporator (b) inlet of the evaporator
(c) exit of the condenser (d) inlet of the condenser
6. Ans. (a)
co
7. A valve which maintains a constant degree of superheat at the end of the evaporator
coil, is called [IES-1993]
(a) automatic expansion valve (b) high side float valve
(c) thermostatic expansion valve (d) low side float valve
.
7. Ans. (c)
valve?
tas
8. Which one of the following is the most important function of thermostatic expansion
[IAS-2003]
(a) To control the degree of superheat (b) To control the evaporator temperature
(c) To control the pressure drop (d) To control the evaporator pressure
8. Ans. (a)
lda
Dry compression in reciprocating compressor is preferred because it
1. prevent valve damage
2. enables use of thermostatic expansion valve.
3. minimizes irreversibility in the compressor.
vi
4. prevents washing out of the lubricating oil from cylinder walls.

Ci
(c) 1 and 4 are correct (d) 3 and 4 are correct

9. Ans. (c)
10. Which one of the following is responsible for the operation of a thermostatic
expansion valve? [IES-2005]
w.
(a) Pressure changes in evaporator (b) Temperature changes in evaporator

(c) Degree of superheat in evaporator (d) Degree of subcooling in evaporator
10. Ans. (c)
11. A thermostatic expansion value in refrigeration system

ww
[IES-1992]
(a) ensures the evaporator completely filled with refrigerant of the load
(b) is suitable only for constant load system
(c) maintains different temperatures in evaporator in proportion to load
(d) none of the above.
11. Ans. (a)
Capillary Tube and Its Sizing

The pressure in a horizontal capillary tube of a refrigeration system decreases due to the
1. frictional resistance offered by the tube wall 2. acceleration of refrigerant in the tube
3. heat transfer from the tube wall 4. decrease in the potential energy
(a) 1 and 4 (b) 2, 3 and 4 (c) 1, 2 and 3 (d) 1 and 2
12. Ans. (d)
m
13. In a domestic refrigerator, a capillary tube controls the flow of refrigerant from the
(a) expansion valve to the evaporator (b) evaporator to the thermostat [IES-1994]
(c) condenser to the expansion valve (d) condenser to the evaporator.
co
13. Ans. (d) In domestic refrigerator, a capillary tube controls the flow of refrigerant from
condenser to evaporator
14. In on-off control refrigeration system, which one of the following expansion devices is
.
used? [IAS-2004]
(a) Capillary tube tas (b) Thermostat
(c) Automatic expansion valve (d) Float valve
14. Ans. (a)
15. Which of the features of expansion valves in the following lists are correctly
matched? [IAS-2004]
lda
Expansion Device Feature
1. Capillary tube : Choking
2. Thermostatic expansion valve : Constant temperature
3. Automatic Expansion valve : Constant degree of superheat
4. Float valve : Mass flow rate of refrigerant is proportional to
load
vi

15. Ans. (c)
Ci
16. The throttling device used in the domestic refrigerator is [IAS-2002]

(a) internally equalized thermostatic expansion valve
(b) externally equalized thermostatic expansion valve
(c) automatic expansion valve
w.
(d) capillary tube

16. Ans. (d)

The pressure in a capillary tube of a refrigerator decreases because
ww
1. tube wall offers frictional resistance .

2. refrigerant accelerates in the tube
3. tube transfer the heat
4. Potential energy decreases
Of these statements
(a) 1 and 2 are correct (b) 1, 2 and 3 are correct
17. Ans. (a)
18. In the window air conditioner, the expansion device used is [GATE-2004]
(a) capillary tube (b) thermostatic expansion valve
(c) automatic expansion valve (d) float valve
18. Ans. (a)
m
. co
tas
vi lda
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
7.
Evaporators
m
1. The deposition of frost on evaporator tubes of an air conditioner will result in
co
(a) decrease in heat transfer (b) increase in heat transfer [IES-1992]
(c) no change in heat transfer (d) increase in capacity of evaporator
1. Ans. (a)
.
2. When a refrigeration plant is started, the evaporator temperature decreases from
(a) It increases continuously

tas
room temperature to the required value. During this period, how does the compressor
power requirement vary? [IAS-2004]
(b) It decreases and then becomes constant
(c) It increases, reaches a peak and then decreases
(d) It remains constant
2. Ans. (a)
lda

vi
Ci
w.
ww
8.
Gas Cycle Refrigeration
m
co
Limitations of Carnot Cycle with Gas as a Refrigerant
1. Air refrigeration cycle is used in [IES-1998]
(a) commercial refrigerators (b) domestic refrigerators
(c) gas liquefaction (d) air-conditioning
.
1. Ans. (a) Air refrigeration cycle finds use in commercial refrigerators.
tas
Reversed Brayton or Joule or Bell Coleman Cycle
2. Match List-I (Process) with List-II (Type) for Bell Coleman or Joule or Reverse Brayton
cycle for gas cycle refrigeration and select the correct answer using the codes given
below the Lists: [IES-2003]
lda
List-I List-II
(Process) (Type)
A Compression 1. Isobaric
B. Heat rejection 2. Isothermal
C. Expansion 3. Isentropic
D. Heat absorption 4. Isenthalpic
vi
(a) 3 1 4 2 (b) 3 1 3 1
(c) 3 2 3 2 (d) 3 1 2 2
2. Ans. (b)
Ci
lists
List I List II [IAS 1994]
w.
A. 1. Vapour compression cycle using

expansion valve
ww
B. 2. Bell-Coleman cycle (gas compression

cycle)
m
C. 3. Vapour compression cycle using
expansion engine
. co
tas
Codes:
A B C A B C
(a) 1 2 3 (b) 2 3 1
lda
(c) 1 3 2 (d) 2 1 3
3. Ans. (d)
4. When the Brayton cycle working in the pressure limits of p1 and p2 is reversed and
operated as a refrigerator, what is the ideal value of COP for such a cycle?
γ −1
vi
⎛p ⎞ 1
(a) ⎜⎜ 2 ⎟⎟ −1 (b) γ −1
[IES 2007]
⎝ p1 ⎠ ⎛ p2 ⎞
⎜⎜ ⎟⎟ −1
⎝ p1 ⎠
Ci
1
(c) (d) None of the above
{
(γ −1) }
⎛ p2 ⎞ γ
⎜⎜ ⎟⎟ −1
⎝ p1 ⎠
w.
γ −1
1 1 rp γ
4. Ans. (c) η H . E = 1 - (γ −1) / γ
∴ (COP)H.P= = γ −1
rp η H .E rp γ −1
ww
1 1
(COP)R = (COP)H.P – 1 = γ −1 = γ −1
rp γ −1 ⎛ p2 ⎞ γ
⎜⎜ ⎟⎟ −1
⎝ p1 ⎠
Application to Aircraft Refrigeration

5. While designing the refrigeration system of an aircraft prime consideration is that the
(a) system has high C.O.P. (b) H.P./ton is low [IES-1993]
(c) weight of refrigerant circulated in the system is low
(d) weight of the refrigeration equipment is low·
5. Ans. (d)
The Joule- Thomson Coefficient and Inversion Curve
m
Reversed Stirling Cycle
. co
tas
vi lda
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
9.
Vapour-Absorption System
m
co
Simple Vapour-Absorption System
1. In a vapour absorption refrigerator, heat is rejected in: [IES-2006]
(a) Condenser only (b) Generator only
(c) Absorber only (d) Condenser and absorber
.
1. Ans. (d)
tas
2. The most common type of absorption system in use in industrial applications is based
on the refrigerant - absorbent combination of [IES-1999]
(a) air-water (b) lithium bromide-air
(c) carbon dioxide-water (d) ammonia-water
2. Ans. (b) Industrial applications use lithium bromide-water combination for absorption
lda
refrigeration units.
3. Solar energy can be directly used in [IES-1999]

(a) vapour compression refrigeration system (b) vapour absorption refrigeration system
(c) air refrigeration system (d) jet refrigeration system
vi
3. Ans. (b)
4. Vapour absorption refrigeration system works using the [IES-1997]

(a) ability of a substance to get easily condensed or evaporated
Ci
(b) ability of a vapour to get compressed or expanded

(c) affinity of a substance for another substance
(d) absorptivity of a substance
4. Ans. (c) Vapour absorption refrigeration system works using the affinity of a substance
for another substance.
w.
5. Which one of the following statements regarding ammonia absorption system is

correct 'I
The solubility of ammonia in water is [IES-1997]
ww
(a) a function of the temperature and pressure of the solution

(b) a function of the pressure of the solution irrespective of the temperature
(c) a function of the temperature of the solution alone
(d) independent of the temperature and pressure of the solution
5. Ans. (a) The solubility of ammonia in water is a function of temperature and pressure
of the solution.
6. The refrigerant used for absorption refrigerators working heat from solar collectors is a
mixture of water and [IES-1996]
(a) carbon dioxide (b) sulphur dioxide (c) lithium bromide (d) freon 12.
6. Ans. (c) The refrigerant used for absorption refrigerators working on heat from solar
collectors is a mixture of water and lithium bromide
7. Waste heat can be effectively used in which one of the following refrigeration
systems?
(a) Vapour compression cycle (b) Vapour absorption cycle.
(c) Air refrigeration cycle (d) Vortex refrigeration system. [IES-1995]
7. Ans. (b) Waste heat can be utilized in vapour absorption cycle.
m
8. Match List I (Basic components of Aqua-ammonia refrigeration system) with List II
(functions of the components in the system) and select the correct answer using the
co
codes given below the lists: [IES-1995]
List I List II
A. Generator 1. Dehydration
B. Analyzer 2. Removal of vapour from strong aqua-ammonia solution
C. Rectifier 3. Producing dry ammonia vapour by removing traces of water particles
.
completely tas
D. Receiver 4. Storage of high pressure liquid ammonia
5. Formation of liquid ammonia from high pressure vapours.
(a) 3 1 2 4 (b) 5 3 4 2
(c) 1 3 2 5 (d) 2 1 3 4
lda
8. Ans. (d)
9. Absorbent in a vapour absorption refrigeration system separates from the refrigerant

only when it [IAS-2007]
(a) Is sufficiently heated (b) Is sprayed on cooling water
(c) Is cooled (d) Reacts with refrigerant
vi
9. Ans. (a)
10. The function of a compressor in a vapour absorption system is performed by the

Ci
(a) absorber (b) absorber and pump [IAS-2000]

(c) pump and generator (d) absorber, pump & generator
10. Ans. (d)
w.
11. In the absorption refrigeration cycle, the compressor of the vapour compression
refrigeration cycle is replaced by [IAS 1994]
(a) liquid pump (b) generator
(c) absorber and generator (d) absorber, liquid pump and generator
11. Ans. (d) The compressor of vapour compression refrigeration cycle is replaced by
ww
absorber, liquid pump and generator in the absorption refrigeration cycle.
12. List I List II [GATE-1997]

(A) Liquid to suction heat exchanger 1. Vapour absorption refrigeration
(B) Constant volume heat addition 2. Vapour compression refrigeration
(C) Normal shock 3. Diesel cycle
(D) Ammonia water 4. Otto cycle
5. Converging nozzle
6. Converging-diverging nozzle
12. Ans. (A) -2, (B) -4, (C)-6, (D)-1
13. A vapour absorption refrigeration system is a

heat pump with three thermal reservoirs as shown in
the figure. A refrigeration effect of 100 W is required
at 250 K when the heat source available is at 400 K.
Heat rejection occurs at 300 K. The minimum value
of heat required (in W) is
m
(a) 167 (b) 100 (c) 80 (d) 20
co
[GATE-2005]
13. Ans. (c)
.
tas
lda
.
vi
14. List I List II [GATE-1997]

(A) Liquid to suction heat exchanger 1. Vapour absorption refrigeration
(B) Constant volume heat addition 2. Vapour compression refrigeration
Ci
(C) Normal shock 3. Diesel cycle

(D) Ammonia water 4. Otto cycle
5. Converging nozzle
6. Converging-diverging nozzle
14. Ans. (A) -2, (B) -4, (C)-6, (D)-1
w.
Maximum Coefficient of Performance of a Heat Operated

Refrigerating Machine
ww
15. Maximum possible COP of a solar absorption refrigeration system with generator
temperature of 360 K, absorber temperature of 300 K, condenser temperature of 300 K
and evaporator temperature of 270 K is [IES-2002]
(a) 9 (b) 6 (c) 3 (d) 1.5
15. Ans. (d)
16. A solar-absorption refrigeration system has generator temperature of 87° C.

evaporator temperature of - 3° C, condenser and absorber temperatures of 27° C each,
then its maximum possible COP is [IES-2001]
(a) 10.0 (b) 9.0 (c) 1.80 (d) 1.50

16. Ans. (d)
17. A reversible heat engine runs between high temperature T1 and low temperature T2.
The work output of this heat engine is used to run reversible refrigeration cycle
absorbing heat at temperature T3 and rejecting at temperature T2. What is the COP of
the combined system? [IAS-2004]
⎛ T1 − T2 ⎞ ⎛ T3 ⎞ ⎛ T2 ⎞ ⎛ T2 − T3 ⎞
(a) ⎜ ⎟⎜ ⎟ (b) ⎜ ⎟⎜ ⎟
m
⎝ T1 ⎠ ⎝ T2 − T3 ⎠ ⎝ T1 − T2 ⎠ ⎝ T3 ⎠
⎛ T1 ⎞ ⎛ T3 ⎞ ⎛ T3 ⎞⎛ T1 ⎞
(c) ⎜ ⎟⎜ ⎟ (d) ⎜ ⎟⎜ ⎟
⎝ T1 − T2 ⎠ ⎝ T2 − T3 ⎠ ⎝ T1 − T3 ⎠ ⎝ T2 − T1 ⎠
co
17. Ans. (a)
Q1 Q2 Q1 − Q2 Q
.
W
= = = orW = 1 × (T1 − T2 )
T1 T2 T1 − T2 T1 − T2 T1 tas
Q3 Q21 Q21 − Q3 W Q
= = = orW = 3 × (T2 − T3 )
T3 T2 T2 − T3 T2 − T3 T3
lda
Q Q
or 1 (T1 − T2 ) = 3 (T1 − T3 )
T1 T3
Q3 ⎛ T3 ⎞ ⎛ T1 − T2 ⎞
or COP = =⎜ ⎟×⎜ ⎟
Q1 ⎝ T2 − T3 ⎠ ⎝ T1 ⎠
vi
Ci
18. The maximum COP for the absorption cycle is given by (TG = generator temperature,
Tc = environment temperature, TE = refrigerated space temperature) [IES-1998]
TE (TG − TC ) T (T − T ) TC (TG − TC ) TG (TC − TE )
(a) (a ) (b) G C E (c ) (d )
TG (TC − TE ) TE (TG − TC ) TG (TC − TE ) TC (TG − TC )
w.
18. Ans. (a)
19. Theoretical maximum C.O.P. of a vapour absorption system (where, TG =generator

temp, TE = evaporator temp, To = environmental temp) is [IES-2003]
ww
TE ⎛ TG − TO ⎞ TE ⎛ TO − TE ⎞ TG ⎛ TG − TO ⎞ TG ⎛ TO − TE ⎞
(a) ⎜ ⎟ (b) ⎜ ⎟ (c) ⎜ ⎟ (d) ⎜ ⎟
TG ⎝ TO − TE ⎠ TG ⎝ TG − TO ⎠ TE ⎝ TO − TE ⎠ TE ⎝ TG − TO ⎠
19. Ans. (a)
20. A heat engine having an efficiency of 70% is used to drive a refrigerator having a co-
efficient of performance of 5. The energy absorbed from low temperature reservoir by
the refrigerator for each kJ of energy absorbed from high temperature source by the
engine is [GATE-2004]
(a) 0.14 kJ (b) 0.71 kJ (c) 3.5 kJ (d) 7.1 kJ

20. Ans. (c)
m
co
21. For the same condenser and evaporator temperatures, the COP of absorption
refrigeration system is less than that of mechanical vapour compression refrigeration
system, since in the absorption refrigeration system, [IAS-1997]
.
(a) a liquid pump is used for compression (b) a refrigerant as well as a solvent is used
tas
(c) absorber requires heat rejection
(d) low grade energy is used to run the system
21. Ans. (d)
22. Air cooling is used for freon compressors whereas water jacketing is adopted for
lda
cooling ammonia compressors. This is because [IES-1997]
(a) latent heat of ammonia is higher than that of freon
(b) thermal conductivity of water is higher than that of air
(c) specific heat of water is higher than that of air
(d) of the larger superheat horn of ammonia compression cycle.
22. Ans. (a) Because of high latent heat of ammonia water cooling is required to remove
vi
large heal
Representation of Vapour Absorption Cycle on In Practical Single-

Ci
Effect Water-Lithium
23. A vapour absorption refrigeration system is a
heat pump with three thermal reservoirs as shown in
the figure. A refrigeration effect of 100 W is required
w.
at 250 K when the heat source available is at 400 K.

Heat rejection occurs at 300 K. The minimum value
of heat required (in W) is
(a) 167 (b) 100 (c) 80
(d) 20
ww
[GATE-2005]
23. Ans. (c)
m
.
co
Double-effect H 0 - LiBr Absorption System
2 2
Electrolux Refrigerator
.
24. In an Electrolux refrigerator: tas [IES-2005]
(a) Ammonia is absorbed in water (b) Ammonia is a absorbed in hydrogen
(c) Hydrogen is evaporated in ammonia (d) Ammonia evaporated in hydrogen
24. Ans. (d)
25. Hydrogen is essential in an Electrolux refrigeration system, because

lda
(a) it acts as a catalyst in the evaporator [IES-1997]
(b) the reaction between hydrogen and ammonia is endothermic in evaporator and
exothermic in absorber
(c) the cooled hydrogen leaving the heat exchanger cools the refrigerant entering the
evaporator
(d) it helps in maintaining a low partial pressure for the evaporating ammonia
vi
25. Ans. (d) Hydrogen gas in Electrolux refrigerator helps in maintaining a low partial
pressure for the evaporating ammonia
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
10. Ejector-Compression System

Water as a Refrigerant
Steam Ejector System
m
. co
tas
vi lda
Ci
w.
ww
11.
Psychometry
m
co
Psychometric Properties
A psychrometer measures
1. wet bulb temperature 2. dew point temperature 3. dry bulb temperature.
.
On these statements
(a) 1 alone is correct
(c) 1 and 3 are correct
tas(b) 2 and 3 are correct
(d) 1, 2 and 3 are correct
1. Ans. (c) A psychrometer measures wet bulb temperature and dry bulb temperature
2. If the specific heats of dry air and water vapour are 1.00 kJ/kg-K and 1.88 kJ/kg-K
respectively and the humidity ratio is 0.011, then the specific heat of moist air at 25°C
lda
and 50% relative humidity will be [IES-1994]
(a) 1.0207 kJ/kg-K (b) 1.869 kJ/kg-K (c) 1.891 kJ/kg-K (d) 0.9793 kJ/kg-K
2. Ans. (a) Specific heat of moist air = specific heat of dry air + humidity ratio x specific
head of water vapour = 1.00 + 0.011 x 1.88 = 1.00 + 0.0207 = 1.0207 kJ/kgoK.
vi
Specific humidity or Humidity ratio

0.622 pv
3. The expression , where Pv = partial pressure of water vapour;
Ci
pb − pv
Pb= atmospheric barometric pressure, is used for calculating [IAS-2001]
(a) relative humidity (b) degree of saturation
(c) humidity ratio (d) pressure of air
3. Ans. (c)
w.
pv
Specific humidity or absolute humidity or humidity ratio (w) = 0.622 ×
pb − pv
0.622 pv
4. The expression is used to determine [IES-1998]
ww
pb − pv
(a) relative humidity (b) specific humidity
(c) degree of saturation (d) partial pressure
4. Ans. (b)
5. If Pa and Pv denote respectively the partial pressure of dry air and that of water vapour
in moist air, the specific humidity of air is given by [IES-2001]
pv pv 0.622 pv 0.622 pv
(a) (b) (c) (d)
pa + pv pa pa pa + pv
5. Ans. (c)
6. When the wet bulb and dry bulb temperatures are equal, which of the following
statements is/are correct? [IES-2005]
1. Air is fully saturated. 2. Dew point temperature is reached.
3. Partial pressure of vapour equals to the total pressure.
m
4. Humidity ratio is 100%.
(a) 1 and 2 (b) 1 only (c) 1, 2 and 3 (d) 2 and 3
6. Ans. (a)
co
7. Moist air exists at a pressure of 1.01 bar. The partial pressure and saturation pressure
of water vapour are 0.01 bar and 0.02 bar respectively. What are the relative humidity
and humidity ratio of the moist air, respectively? [IAS-2004]
(a) 50% and 0.00622 (b) 100% and 0.0126
.
(c) 50% and 0.0126 (d) 100%and 0.00622
7. Ans. (a)
PVtas
relative humidity ( Q ) =
PS
× 100% =
0.01
0.02
× 100% = 50%
P 0.01
Specific humidity ( μ ) = 0.622 V = 0.622 × = 0.00622
Pb − Pv 1.01 − 0.01
lda
8. Dew point temperature of air at one atmospheric pressure (1.013 bar) is 18oC. The air
dry bulb temperature, is 30oC. The saturation pressure of water at 18oC and 30oC are
0.02062 bar and 0.04241 bar respectively. The specific heat of air and water vapour
respectively are 1.005 and 1.88 kJ/kg K and the latent heat of vaporization of water at
0oC is 2500 kJ/kg. The specific humidity (kJ/kg of dry air) and enthalpy (kJ/kg of dry air)
vi
of this moist air respectively, are [GATE-2004]

(a) 0.01051, 52.64 (b) 0.01291, 63.15 (c) 0.01481, 78.60 (d) 0.01532, 81.40
8. Ans. (a)
Ci
w.
ww
Relative humidity
pv
9. The equation φ = is used to calculate the (pv = partial pressure of water vapour in
ps
moist air at a given temperature, Ps = saturation pressure of water vapour at the same
temperature) [IES-1999]
(a) relative humidity (b) degree of saturation
(c) specific humidity (d) absolute humidity
m
9. Ans. (a)
10. If the volume of moist air with 50% relative humidity is isothermally reduced to half its
original volume, then relative humidity of moist air becomes [IES-2003]
co
(a) 25 % (b) 60 % (c) 75 % (d) 100 %
10. Ans. (d)
pv1
Relative humidity(RH)1 = = 0.5 or pv1 = 0.5 × ps
ps
.
Where subscript ' v' refers to vapour state.
tas
Where subscript ' s' refers to saturation state.
⎛V ⎞ ⎛ 2V ⎞
pv 2 = pv1 × ⎜ 2 ⎟ = ( 0.5 ps ) × ⎜ 1 ⎟ = ps
⎝ V1 ⎠ ⎝ V1 ⎠
lda
p p
∴Relative humidity(RH)2 = v 2 = s = 100%
ps ps
11. The wet bulb depression is zero, when relative humidity is equal to: [IES-2006]
(a) 100% (b) 60% (c) 40% (d) Zero
11. Ans. (a)
vi
12. Evaporative air-cooler is used effectively when [IES-1995]

(a) dry bulb temperature is very close to the wet bulb temperature
(b) dry bulb temperature is high and relative humidity is high
Ci
(c) dry-bulb temperature is low and relative humidity is high

(d) dry bulb temperature is high and the relative humidity is low.
12. Ans. (d)
13. For which one of the following DBT, WBT and DPT has the same value?
w.
(a) 0 per cent relative humidity line (b) 100 per cent relative humidity line
(c) 50 per cent relative humidity line (d) None of the above [IAS-2007]
13. Ans. (b)
ww
14. Match List I (Quantity) with List II (Measuring Device) and select the correct answer
using the codes given below the Lists: [IAS-2002]
List I List II
(Quantity) (Measuring Device)
A. Engine speed 1. Manometer
B. Fuel heating value 2. Tachometer
C. Air velocity 3. Hydrometer
D. Relative humidity of air 4. Calorimeter
5. Hygrometer
(a) 2 5 1 4 (b) 1 5 3 4
(c) 2 4 1 5 (d) 1 4 3 5
14. Ans. (c)
15. If a sample of moist air of 50% relative humidity at atmospheric pressure is

isothermally compressed to a pressure of two atmospheres, then [IAS-1999]
(a) its relative humidity will reduce to 25%
(b) its relative humidity will remain unchanged
m
(c) the sample of air will become saturated
(d) saturation pressure will increase to twice the value
pv
15. Ans. (b) Relative humidity (φ ) = ,Here totalpressureincreasedbut partial
co
ps
pressureof water vapour isunchanged sonochangeinrelativehumidity
16. A sample of moist air is at a temperature T and relative humidity 50%.Apart of the
.
moisture is removed adiabatically by using an adsorbent. If the heat of adsorption is
tas
negligible, the resulting air will have the same
(a) dry bulb temperature but a lower wet bulb temperature
(b) wet bulb temperature but a higher dry bulb temperature
[IAS-1998]
(c) dry bulb temperature but a higher wet bulb temperature

(d) wet bulb temperature but a lower dry bulb temperature
16. Ans. (b)
lda
17. For a typical sample of ambient air (at 35 °C, 75% relative humidity and standard
atmospheric pressure), the amount of moisture in kg per kg of dry air will be
approximately [GATE-2005]
(a) 0.002 (b) 0.027 (c) 0.25 (d) 0.75
17. Ans. (b)
vi
Ci
w.
18. For air at a given temperature, as the relative humidity is increased isothermally,
(a) the wet bulb temperature and specific enthalpy increase [GATE-2001]
(b) the wet bulb temperature and specific enthalpy decrease
ww
(c) the wet bulb temperature increases and specific enthalpy decreases
(d) the wet bulb temperature decreases and specific enthalpy increases
18. Ans. (a, c)
Dew point temperature
19. The minimum temperature to which water can be cooled in a cooling tower is
(a) the dew point temperature of air (b) the wet bulb temperature of air.
(c) the dry bulb temperature of air (d) the ambient air temperature. [IES-1995]
19. Ans. (a) Water can be cooled in a cooling tower upto dew point temperature of air.
20. In a cooling tower, the minimum temperature to which water can be cooled is equal
to the
(a) dew point temperature of the air at the inlet [IES-2001]
(b) dry bulb temperature of the air at the inlet
(c) thermodynamic wet bulb temperature of the air at the inlet
(d) mean of the dew point and dry bulb temperature of the air at the inlet
m
20. Ans. (a)
21. In a chilled-water spray pond, the temperature of water is lower than dew point
co
temperature of entering air. The air passing through the spray undergoes [IES-1999]
(a) cooling and humidification (b) cooling and dehumidification
(c) sensible cooling (d) dehumidification
21. Ans. (b) In this case condensation of moisture takes place which results in fall in
specific humidity ratio. Cooling and dehumidification take place.
.
tas
22. When a stream of moist air is passed over a cold and dry cooling coil such that no
condensation takes place, then the air stream will get cooled along the line of
(a) constant wet bulb temperature (b) constant dew point temperature [IES-1996]
(c) constant relative humidity (d) constant enthalpy.
22. Ans. (b) When a stream of moist air is passed over a cold and dry cooling coil such
lda
that no condensation takes place, then air stream is cooled along constant dew point
temperature
23. Evaporative regulation of body temperature fails when the body temperature is
(a) more than wet bulb temperature but less than dry bulb temperature
(b) more than dew point but less than wet bulb temperature
vi
(c) more than dew point but less than dry bulb temperature [IAS-1999]
(d) less than dew point
23. Ans. (d)
Ci
24. Dew point temperature is the temperature at which condensation begins when the air
is cooled at constant [GATE-2006]
(a) volume (b) entropy (c) pressure (d) enthalpy
24. Ans. (c)
w.
ww
25. For air with a relative humidity of 80% [GATE-2003]

(a) the dry bulb temperature is less than the wet bulb temperature
(b) the dew point temperature is less than wet bulb temperature
(c) the dew point and wet bulb temperatures are equal
(d) the dry bulb and dew point temperatures are equal
25. Ans. (b)
m
co
1. Dew point is reached by cooling air at constant moisture content.
2. Wet bulb temperature changes by addition of moisture at constant enthalpy.
3. For saturated air, the dry bulb temperature, wet bulb temperature and dew point are
.
the same.
tas
4. Dehumidification of air is achieved by heating. [IAS-1995]
(a) 1 and 3 are correct (b) 1 and 2 are correct(c) 3 and 4 are correct (d) 1 alone is
correct
26. Ans. (a)
lda
Degree of saturation
27. The ratio of weight of water vapour associated with unit weight of dry air to the
weight of water vapour associated with unit weight of dry air saturated at the same dry-
bulb temperature and pressure is known as [IAS-2000]
(a) specific humidity (b) relative humidity (c) absolute humidity (d) degree of saturation
vi
27. Ans. (d)
28. If Pv is the partial pressure of vapour, Ps is the partial pressure of vapour for
saturated air and Pb is the barometric pressure, the relationship between relative
Ci
humidity ' ɸ' and degree of saturation ' μ' is given by [IES-2001]
⎡ pb − ps ⎤ ⎡ pb − pv ⎤ pv pv
(a) μ = φ ⎢ ⎥ (b) μ = φ ⎢ ⎥ (c) μ = φ (d) μ = φ
⎣ pb − pv ⎦ ⎣ pb − ps ⎦ pb ps
w.
28. Ans. (a)
29. Air at state 1 (dpt 1°C, W = 0.0040 kg/kgair) mixes with air at state 2 (dpt 18°C, W =
0.0051 kg/kgair) in the ratio 1 to 3 by weight. The degree of saturation (%) of the mixture
is (the specific humidity of saturated air at 13.6°C, W = 0.01 kg/kgair) [IES-1999]
ww
(a) 25 (b) 30 (c) 48 (d) 62

29. Ans. (c)
0.004 + 3 × 0.0051
kg of moisture actually contained in mixture = = 0.0048
4
kg of moisture in saturated air of mixture = 0.01 kg/kg of air
0.0048
So, Degree of saturation = × 100% = 48%
0.01
30. Match List I with List II and select the correct answer using the code given below the
Lists: [IES-2005]
List I List II
A Degree of saturation 1. Measure of latent enthalpy of moist air
B. Dry bulb temperature 2. Measure of total enthalpy of moist air
C. Wet bulb temperature 3. Measure of the capacity of air to absorb moisture
D. Dew point temperature 4. Measure of sensible enthalpy of moist air
A B C D A B C D
m
(a) 2 1 3 4 (b) 3 4 2 1
(c) 2 4 3 1 (d) 3 1 2 4
30. Ans. (b)
co
1. The specific humidity is the ratio of the mass of water vapour to the mass of dry
air in a given volume of the mixture
2. The relative humidity of the atmospheric air is the ratio of the actual mass of the
.
water vapour in a given volume to that which it would have if it were saturated at
tas
the same temperature
3. The degree of saturation is defined as the ratio of the specific humidity of a
mixture to the specific humidity of the mixture when saturated at the same
temperature
lda
31. Ans. (d)
Wet Bulb Temperature (WBT)

32. If wet bulb depression is equal to the sum of range and approach of a cooling tower,
vi
then the water [IAS-1999]

(a) inlet temperature is equal to the wet bulb temperature of ambient air.
(b) outlet temperature is equal to the wet bulb temperature of ambient air.
Ci
(c) inlet temperature is equal to dry bulb temperature of ambient air.

(d) outlet temperature is equal to dry bulb temperature of ambient air.
32. Ans. (c)
33. In a cooling tower the sum of range and approach is equal to twice the wet bulb
w.
depression. Then [IES-2003]

(a) Dry bulb temperature is mean of water inlet temperature and wet bulb temperature
(b) Dry bulb temperature is mean of water outlet temperature and wet bulb temperature
(c) Water inlet temperature is mean of dry bulb temperature and wet bulb temperature
(d) Water inlet temperature is mean of water outlet temperature and wet bulb
ww
temperature
33. Ans. (a)
Ti = inlet temperature of water in cooling tower

To = outlet temperature of water in cooling tower
Approach = To - Twb
Wet bulb depression = Tdb - Twb
From the given statement, (Ti - To ) + (To - Twb ) = 2 (Tdb - Twb )
Ti + Twb
or Tdb =
m
2
34. In case A, moist air is adiabatically saturated and in case B, moist air is isobarically
saturated. The saturation temperatures in cases A and B are respectively
co
(a) dry bulb temperature and wet bulb temperature [IES-2002]
(b) dew point temperature and wet bulb temperature
(c) wet bulb temperature and dew point temperature
(d) wet bulb temperature and dry bulb temperature
.
34. Ans. (c)

tas
When dry bulb and thermodynamic wet bulb temperatures are same;
[IES-2001]
1. humidity ratio is 100% 2. partial pressure of water vapour equals total pressure
3. air is fully saturated 4. dew point temperature is reached
Select the correct statement(s) using the codes given below:
lda
Codes:
(a) 3 alone (b) 1 and 2 (c) 3 and 4 (d) 1, 2, 3 and 4
35. Ans. (d)
36. At 100% relative humidity, the wet bulb temperature is [IES-1995]

vi
(a) more than dew point temperature (b) same as dew point temperature
(c) less than dew point temperature (d) equal to ambient temperature.
36. Ans. (c)
Ci
37. In a saturated air-water vapour mixture, the [IES-1993]

(a) dry bulb temperature is higher than the wet bulb temperature
(b) dew point temperature is lower than the wet bulb temperature
(c) dry bulb, wet bulb and dew point temperatures are the same
(d) dry bulb temperature is higher than the dew point temperature
w.
37. Ans. (c) In a saturated air-water vapour mixture, the dry bulb, wet bulb and dew point
temperatures are the same.

ww
If moist air is adiabatically saturated in an air washer than

1. wet bulb temperature remains constant
2. relative humidity increases
3. dry bulb temperature decreases
4. humidity ratio decreases
38. Ans. (a)
39. Desert coolers are suitable for hot very dry outside conditions because
(a) water is recirculated in the spray [IAS 1994]
(b) beat is neither added nor removed from the water
(c) wet bulb depression (t-t) is very large (d) large quantity of air can be conditioned
39. Ans. (c)
40. If the measured wet-bulb temperature and the thermodynamic wet-bulb temperature
are equal then the non-dimensional number with a value of unity is the [IAS-2000]
(a) Lewis number (b) Prandtl number (c) Schmidt number (d) Sherwood number
m
40. Ans. (a) Le = 0.945
41. When the wet and dry bulb temperatures are identical, which of the following
co
statements is/are true? [IES-2003]
1. Air is fully saturated 2. Dew point temperature is reached
3. Humidity ratio is unity 4. Partial pressure of vapour equals total pressure
(a) 1 only (b) 1 and 2 (c) 3 and 4 (d) 1, 2, 3 and 4
.
41. Ans. (b) tas
42. When dry-bulb and wet-bulb temperatures are identical, it means that the
(a) air is fully saturated and dew-point temperature has reached [IES-2000]
(b) air is fully saturated
(c) dew-point temperature has reached and humidity is 100%
lda
(d) partial pressure of water vapour is equal to total pressure
42. Ans. (b)
Adiabatic saturation of air and adiabatic saturation temperature

43. During adiabatic saturation process of air, wet bulb temperature [IES-1999]
(a) increases and dry bulb temperature remains constant
vi
(b) remains constant and dry bulb temperature increases

(e) remains constant and dry bulb temperature decreases
(d) decreases and dry bulb temperature remains constant
43. Ans. (b)
Ci
44. During the adiabatic cooling of moist air [IES-1996]

(a) DBT remains constant (b) specific humidity remains constant.
(c) relative humidity remains constant (d) WBT remains constant.
w.
44. Ans. (d) During the adiabatic cooling of moist air, wet bulb temperature remains
constant
45. Water in an insulated evaporative cooler evaporates at the rate of 0.003 kg/s. Air
flow rate is 1kg/s. What is the air temperature decrease if the specific heat of humid air is
ww
1kJ/kg K and latent heat of water is 2500 kJ/kg? [IAS-2004]

(a) 2.50 C (b) 3.00 C (c) 7.50 C (d) 100 C
45. Ans. (c) Heat balance gives us
ma c p ΔT = mw × L
mw × L 0.003 × 2500
or ΔT = = = 7.50 C
ma × c p 1× 1
46. Total heat transfer from a wetted surface depends upon [IAS-2003]
(a) difference in temperature between surface and air
(b) difference in humidity ratio of air and air saturated at wet surface temperature
(c) difference in enthalpy between saturated air at surface temperature and that of air
(d) difference in entropy between saturated air at surface temperature and that of air
46. Ans. (d)
47. The main process which takes place in a desert-cooler is
m
[IAS-2001]
(a) sensible cooling (b) dehumidification
(c) adiabatic saturation (d) cooling and dehumidification
47. Ans. (c) In a desert-cooler water vaporize and latent heat of vaporization is cools the
co
air.
Psychometric Chart
.
48. Moist air is a mixture of dry air and water vapour. Hence three independent intrinsic
tas
thermodynamic properties are required to fix its thermodynamic state. While using
psychometric chart, however, only two thermodynamic properties are needed since,
psychometric chart
(a) is an approximation to actual properties [IES-1993]
(b) assumes that both water vapour and dry air behave like perfect gases
lda
(c) is drawn for actual properties of water vapour and dry air
(d) is drawn for a fixed pressure
48. Ans. (d) The psychometric chart is drawn for a fixed pressure (standard atmospheric
pressure) and thus only two thermodynamic properties are needed to fix thermodynamic
state.
vi
49. With respect to the following figure which shows four processes on the psychometric
chart, match List I with List II and select the correct answer using the codes given below
the lists:
Ci

A. Process RS 1. Cooling and humidifying
B. Process RT 2. Sensible heating
C. Process RU 3. Cooling and dehumidifying
D. Process RW 4. Humidifying
w.
(a) 2 3 1 4 (b) 1 4 2 3
(c) 3 1 4 2 (d) 3 2 1 4
49. Ans. (c)
ww
50. The statements concern psychometric chart. [GATE-2006]

1. Constant relative humidity lines are uphill straight lines to the right
2. Constant wet bulb temperature lines are downhill straight lines to the right
3. Constant specific volume lines are downhill straight lines to the right
4. Constant enthalpy lines are coincident with constant wet bulb temperature lines
Which of the statements are correct?
50. Ans. (a)
51. Which one of the following is

correct for the process 1-2 shown
above?
(a) The partial pressure of water
vapour in air remains constant
(b) Specific humidity of air remains
constant
(c) Enthalpy of air remains constant
m
(d) Dry bulb temperature of air
remains constant
co
[IES-2006]
51. Ans. (c)
.
1. Relative humidity
tas
52. Which of the following properties increasers) during sensible heating of air-water
vapour-mixture?
2. Humidity ratio
[IES-2003]
3. Wet bulb temperature 4. Specific enthalpy of air-vapour mixture

lda
(a) 1 and 2 (b) 3 only (c) 2 and 3 (d) 3 and 4
52. Ans. (d)
vi
Ci
w.
53. Atmospheric air at 35°C and 60% RH can be brought to 20°C and 60% RH by:
(a) Cooling and dehumidification process (b) Cooling and humidification process
(c) Adiabatic saturation process (d) Sensible cooling process
53. Ans. (a)
1-2 = 1-2` + 2`-2
ww
cooling + de-humidification
[IES-2006]
54. Assertion (A): On the psychometric chart, constant enthalpy lines and constant wet
bulb lines are the same. [IAS-1995]
Reason (R): For the same wet bulb temperature, the moisture content remains constant.
54. Ans. (a) Both A and R are true and R is the correct explanation of A
55. To fix the state point in respect of air-vapour mixtures, three intrinsic properties are
needed. Yet, the psychometric chart requires only two because [IES-1998]
(a) water vapour is in the superheated state (b) the chart is for a given pressure
(c) the chart is an approximation to true values (d) the mixtures can be treated as a
perfect gas
55. Ans. (b) Psychometric chart is plotted for standard atmospheric pressure and as
m
such only 2 coordinates are used to fix the state point. For pressures other than
standard atmospheric, some correction is required.
co
In psychrometry, wet-bulb temperature is a measure of enthalpy of moist air, so that in
the psychometric chart,
1. the constant enthalpy lines are also constant wet bulb temperature lines
2. the wet bulb and dry bulb temperature are same at any condition
.
3. the wet - bulb and dry-bulb temperature are equal at saturation condition.
tas
Of these statements.
(a) 1 alone is correct (b) 1 and 2 are correct
(c) 1 and 3 are correct (d) 2 and 3 are correct.
56. Ans. (c)
lda
57. Various psychometric processes are shown in the
figure below.
Process in Figure Name of the process
P. 0-1 1. Chemical dehumidification
Q. 0-2 2. Sensible heating
R. 0-3 3. Cooling and dehumidification
vi
S. 0-4 4. Humidification with steam

injection
T. 0-5 5. Humidification with water [GATE-2005]
injection
Ci
The matching pairs are

(a) P-1, Q-2, R-3, S-4, T-5 (b) P-2, Q-1, R-3, S-5, T-4
(c) P-2, Q-1, R-3, S-4, T-5 (d) P-3, Q-4, R-5, S-1, T-2
57. Ans. (b)
w.

(a) Pressure and temperature are independent during phase change.
(b) An isothermal line is also a constant pressure line in the wet vapour region.
(c) Entropy decreases during evaporation.
ww
(d) The term dryness fraction is used to specify the fraction by mass of liquid in a mixture
of liquid and vapour.
59. Ans. (b)
Basic Processes in Conditioning of Air

Sensible heating
During sensible heating

1. moisture content increases2. dry bulb temperature and wet bulb temperature increase
3. dew point remains constant 4. relative humidity increases
(a) 1, 2 and 3 (b) 2,3 and 4 (c) 2 and 3 (d) 1 and 2
60. Ans. (c) During sensible heating, dry bulb temperature and wet bulb temperature
increase, dew point remains unchanged. Moisture content remains same and relative
humidity decreases. This statements 2 and 3 are correct
m
the lists:
List I List II
co
A. Steam spray into air 1. Sensible cooling
B. Air passing over a coil carrying steam 2. Cooling and dehumidification
C. Air passing over coil having temperature less 3. Heating and humidification
than dew point 4. Sensible heating [IAS-1996]
D. Air passing over a coil having temperature
.
above the dew point but below the wbt
tas
(a) 2 1 3 4 (b) 3 1 2 4
(c) 3 4 2 1 (d) 4 3 2 1
61. Ans. (c)
lda
62. When moist air comes into contact with a wetted surface whose temperature is less
than the dry-bulb temperature but more than the wet-bulb temperature? [IAS-2000]
(a) sensible, latent and net heat transfers are from air to surface
(b)both sensible and net heat transfers are from air to surface but latent heat transfer is
from surface to air
(c)sensible heat transfer is from air to surface but both latent and net heat transfers are
vi
from surface to air

(d) sensible heat transfer is from surface to air but both latent and net heat transfers are
from air to surface.
62. Ans. (b)
Ci
63. When atmospheric air is heated at constant pressure, its [GATE-2000]

(a) humidity ratio does not change (b) relative humidity increases
(c) dew point temperature does not change (d) wet bulb temperature increases
w.
63. Ans. (a, c)
Sensible cooling
ww
64. During sensible cooling of air, [IES-1998]

(a) its wet bulb temperature increases and dew point remains constant
(b) its wet bulb temperature decreases and the dew point remains constant
(c) its wet bulb temperature increases and the dew point decreases
(d) its wet bulb temperature decreases and dew point increases
64. Ans. (b) During sensible cooling of air, its wet bulb temperature decreases but dew
point remains unchanged.
65. During sensible cooling [IES-1992]

(a) Relative humidity remains constant (b) Wet bulb temperature increases
(c) Specific humidity increases (d) Partial pressure of vapour remains
constant.
65. Ans. (d)
66. If moist air is sensibly cooled above its dew point, which of the following statements
are correct? [IAS-2004]
1. Relative humidity decreases. 2. Wet bulb temperature decreases.
m
3. Wet bulb temperature increases. 4. Humidity ratio remains constant.
Codes:
co
(a) 1 and 2 (b) 1and 3 (c) 3 and 4 (d) 2 and 4
66. Ans. (d)
Humidification
.
Dehumidification tas
67. When warm saturated air is cooled [IES-2000]
(a) excess moisture condenses
(b) excess moisture condenses but relative humidity remains unchanged
(c) excess moisture condenses and specific humidity increases but relative humidity
remains unchanged.
lda
(d) specific humidity increases and relative humidity decreases
67. Ans. (a)
Chemical Dehumidification
In chemical dehumidification process
vi
1. dew point temperature decreases. 2. wet bulb temperature decreases

3. dry bulb temperature increases.
Of these statements
Ci
(a) 1, 2 and 3 are correct (b) 1 and 2 are correct

68. Ans. (b) Statements 1 and 2 are correct because dry bulb temperature remains
constant in dehumidification process.
w.
69. During chemical dehumidification

(a) wet bulb temperature constant but enthalpy changes
(b) dry bulb temperature remains constant
(c) both dew point and we bulb temperature remain constant
(d) enthalpy and web bulb temperature remain constant
ww
[IAS-1996]
69. Ans. (d)
70. During chemical dehumidification process of air [GATE-2004]

(a) dry bulb temperature and specific humidity decrease
(b) dry bulb temperature increases and specific humidity decreases
(c) dry bulb temperature decreases and specific humidity increases
(d) dry bulb temperature and specific humidity increase
70. Ans. (b)
m
71. Select statements from List II matching the processes in List I. Enter your answer as
D,C if the correct choice for (1) is D and that for (2) is (C) [GATE-1999]
co
List I List II
(a) Cooling and dehumidification (A) Dry bulb temperature increases, but
dew - point temperature decreases.
(b)Chemical dehumidification (B) Dew - point temperature increases and
dry - bulb temperature remains uncharged
.
tas (C) Dry - bulb and wet - bulb temperatures
decrease
(D) Dry - bulb temperature decreases, but,
dew - point temperature increases
71. Ans. (c, d)
lda
72.. Which one of the following statement is correct? [IAS-2003]
(a) Dehumidifier coil surface temperature is above both the dew point temperature but
below the freezing point temperature
(b) Dehumidifier coil surface temperature is below the dew point temperature but above
the freezing point temperature
(c) Dehumidifier coil surface temperature is below the dew point temperature and the
vi
freezing point temperature

(d) Dehumidifier coil surface temperature is above the dew point temperature and the
freezing point temperature
72. Ans. (b)
Ci
Heating and humidification

73. In summer air-conditioning, the conditioned air passing through the space undergoes
a process of [IAS-1998]
w.
(a) sensible cooling (b) sensible heating

(c) cooling and dehumidification (d) heating and humidification
73. Ans. (d)
74. The process in a hot water spray washer maintained at a temperature of 400C,
ww
through which unsaturated air at 10° C dry bulb temperature and 50% relative humidity
passes, is
(a) sensible heating (b) humidification [IAS-1997]
(c) heating and humidification (d) heating and dehumidification
74. Ans. (c)
75. Water at 42°C is sprayed into a stream of air at atmospheric pressure, dry bulb
temperature of 40oC and a wet bulb temperature of 20oC. The air leaving the spray
humidifier is not saturated. Which of the following statements is true? [GATE-2005]
(a) Air gets cooled and humidified (b) air gets heated and humidified
(c) Air gets heated and dehumidified (d) Air gets cooled and dehumidified
75. Ans. (b)
m
co
Cooling and dehumidification
.
76. Air at 35°C DBT and 25°C dew point temperature passes through the water shower
(a) Cooling and humidification

(c) Cooling and dehumidification
tas
whose temperature is maintained at 20°C. What is the process involved?
(b) Sensible cooling
(d) Heating and humidification
[IES-2004]
76. Ans. (c) As temp of shower (200C) is below DBT (350C) sensible cooling will
occur.
As temp of the shower (200C) is below Dew point temp (250C) some moisture of will
lda
condensed and form water droplets i.e. dehumidification.
77. If air is passed through a solid chemical absorbent, the psychometric process
followed is
(a) heating and dehumidification with the bulb temperature remaining fairly constant
(b) cooling and dehumidification
vi
[IES-1992]
(c) dehumidification with sharp rise in wet bulb temperature
(d) dehumidification at constant dry bulb temperature.
77. Ans. (a)
Ci
78. It is desired to condition the outside air from 70% RH and 45°C dry bulb to 50% RH
and 25°C dry bulb room condition. The practical arrangement would be [IAS 1994]
(a) cooling and dehumidification (b) dehumidification and pure sensible cooling,
(c) cooling and humidification (d) dehumidification
w.
78. Ans. (a)
79. For the following "Matching" exercise, choose the correct one from among the
alternatives
ww
A, B, C and D [GATE-2000]
Group 1 Group 2
1. Marine Diesel Engine (A) Two stroke engine
2. Air conditioning (B) Four stroke engine
3. Steam Power Plant (C) Rotary engine
4. Gas Turbine Power Plant (D) Cooling and dehumidification
(E) Cooling tower
(F) Brayton cycle
(G) Rankine cycle
(H) D - slide valve

(a) (b) (c) (d)
1-B 1-C 1-C 1-A
2-E 2-F 2-F 2-D
3-F 3-E 3-G 3-G
4-H 4-G 4-E 4-F
79. Ans. (d)
80. For cooling and dehumidifying of unsaturated moist air, it must be passed over a coil
m
at a temperature [IES-2002]
(a) of adiabatic saturation of incoming stream
(b) which is lower than the dew point of incoming stream
co
(c) which lies between dry bulb and wet bulb temperature
(d) which lies between wet bulb and dew point temperature of incoming stream
80. Ans. (b)
81. To cool and dehumidify a stream of moist air, it must be passed over the coil at a
.
temperature tas
(a) which lies between the dry bulb and wet bulb temperatures of the incoming stream
(b) which lies between the wet bulb and dew point temperature of the incoming stream
(c) which is lower than the dew point temperature of the incoming stream
(d) of adiabatic saturation of incoming steam [IAS-1995]
81. Ans. (c)
lda
Cooling and humidification

82. Assertion (A): During cooling with humidification dew point decreases.
Reason (R): The process results in increased specific humidity. [IES-1992]
82. Ans. (d)
vi
83. A cooling coil with a bypass factor of 0.1 and apparatus dew point (adp) of 12°C
comes in contact with air having a dry-bulb temperature of 38° C and dew point of 9° C.
Over the cooling coil, the air would undergo
Ci
(a) sensible cooling (b) cooling and humidification

(c) cooling and dehumidification (d) adiabatic saturation [IAS-2001]
83. Ans. (b) Apparatus due point = 120C
∴ minimum temperature expected = 12 × (1 − 0.1) = 10.80 C
w.
So the process is cooling and humidification as 90C is lower than 10.80C
84. If air at dry-bulb temperature of 35° C and dew point temperature of 20° C passes
through a cooling coil which is maintained at 25° C, then the process would be
ww
(a) sensible cooling (b) cooling and dehumidification [IAS-1997]

(c) cooling and humidification (d)cooling at constant wet bulb temperature
84. Ans. (c)
85. When the air is passed through an insulated chamber having sprays of water
maintained at a temperature higher than the dew point temperature of entering air but
lower than its dry bulb temperature, then the air is said to be [IES-1994]
(a) cooled and humidified (b) cooled and dehumidified
(c) heated and humidified (d) heated and dehumidified
85. Ans. (a) When air is passed through spray of water at temperature higher than dew
point temperature of entering air and lower than its dry bulb temperature, then air is
cooled and humidified.
86. In order to cool and dehumidify a stream of moist air, it must be passed over a coil at
a temperature [IAS-2004]
(a) which lies between the dry bulb and wet bulb temperatures of the incoming stream
(b) which lies between the wet bulb and dew point temperatures of the incoming stream
(c) which is lower than the dew point temperature of the incoming stream
m
(d) of adiabatic saturation of incoming stream
86. Ans. (c)
co
Heating and dehumidification
Sensible heat factor (SHF)
.
87. What is the sensible heat factor during the heating and humidification process equal
to? tas [IES-2006]
H1 + H 2 H 2 − H1 H1 + H 2 H 3 + H1
(a) (b) (c) (d)
H 3 − H1 H 3 − H1 H1 − H 2 H 2 − H1
Where, H1= Total heat of air entering the heating coil
H2 = Total heat of air leaving the heating coil
lda
H3 = Total heat of air at the end of the humidification
87. Ans. (d)
88. The latent heat load in an auditorium is 25% of the sensible heat load. The value of
sensible heat factor (S H F) is equal to [IES-2002]
(a) 0.25 (b) 0.5 (c) 0.8 (d) 1.0
vi
88. Ans. (c)
89. In a psychometric process, the sensible heat added is 30 kJ/sec and the latent heat
added is 20 kJ/sec. The sensible heat factor for the process will be [IES-1993]
Ci
(a) 0.3 (b) 0.6 (c) 0.67 (d) 1.5

sensible heat 30
89. Ans. (b) Sensible heat factor = = = 0.6
sensible heat + latent heat 30 + 20
w.
90. In an air-conditioning process, 5kJ/min heat is extracted from a room. If the sensible
heat factor is 0.8, then the latent heat extracted will be [IAS-1997]
(a) 4 kJ/min (b) 2 kJ/min (c) 1 kJ/min (d) 0.25 kJ/min
SH SH
90. Ans. (c) SHF = or 0.8 = or SH = 4 kJ / min, LH = 1 kJ / min
ww
SH + LH 5
92. In an auditorium, the heat generated due to the occupants and the electric lights and
other equipments is 100 kW. The rate of generation of excess moisture is 60kg/hr. If an
air-conditioner is supplying conditioned air to the auditorium at the rate of 500 m3/min,
then the sensible heat factor (SHF) for the auditorium is [IAS 1994]
(a) 0.27 (b) 0.40 (c) 0.73 (d) 0.95
92. Ans. (c)
Psychometric Processes in Air Conditioning Equipment

Bypass factor
93. Atmospheric air at dry bulb temperature of 15°C enters a heating coil whose surface
temperature is maintained at 400C. The air leaves the heating coil at 25°C. What will be
the by-pass factor of the heating coil? [IES-2004]
(a) 0.376 (b) 0.4 (c) 0.6 (d) 0.67
Actual temp. increased 40 − 25
93. Ans. (b) BPF = 1 − = 1− = 1 − 0.6 = 0.4
m
m
Max possible temp. increased 40 − 15
94. In order to have a low bypass factor of a cooling coil, the fin spacing and the number
co
of tube rows should be: [IES-2005]
(a) Wide apart and high, respectively (b) Wide apart and low, respectively
(c) Close and high, respectively (d) Close and low, respectively
94. Ans. (c)
.
95. Air is 20°C dry bulb temperature and 40% relative humidity is heated upon 40°C
The bypass factor of the heater is

(a) 0.20 (b) 0.25
tas
using an electric heater, whose surface temperature is maintained uniformly at 45°C.
(c) 0.88 (d) 1

[IES-1999]
t3 − t2 45 − 40
95. Ans. (a) Bypass factor = = =0.2
t3 − t1 45 − 20
lda
96. For low bypass factor a cooling coil, the fin spacing and the number of tube rows will
be respectively [IES-1998]
(a) high and high (b) high and low (c) low and high (d) low and low
96. Ans. (d) Low bypass factor is indication of poor heat transfer. For better transfer, no.
of coils should be more and fin spacing should be higher
vi
97. The atmosphere air at dry bulb temperature of 15°C enters a heating coil maintained
at 40°C. The air leaves the heating coil at 25°C. The bypass factor of the heating coil is
Ci
(a) 0.375 (b) 0.4 (c) 0.6 (d) 0.67 [IES-1994]

40 − 25
97. Ans. (d) Bypass factor of heating coil = = 0.67
40 − 15
98. In the case of sensible cooling of air, the coil efficiency is given by (BPF = Bypass
w.
factor)
(a) BPF-1 (b) 1-BPF (c) BPF (d) 1 + BPF [IES-1993]
98. Ans. (b) Coil efficiency in the sensible cooling is = 1 - BPF
99. Assertion (A): Bypass factor of a cooling coil decreases with decrease in face
ww
velocity. [IAS-2003]
Reason (R): Air gets more time to contact the cooling coil at lower face velocity.
99. Ans. (b)
100. The condition of air for a cooling and

dehumidification system is given by th point A at
intake, B at discharge as marked on a
psychometric chart. It C is the apparatus dew
point, the bypass factor is given by
CA CA BC BC
(a) (b) (c ) (d )
AB BC AB CA [IAS-1996]
m
100. Ans. (d)
101. Consider the following statements

1. Low value of the bypass factor for an air-conditioning equipment signifies higher
co
performance of the equipment [IAS 1994]
2. Bypass factor for an air-conditioning equipment signifies the fraction of ambient air
mixed with the air to be conditioned.
3. Bypass factor for an air-conditioning equipment signifies the fraction of the air to be
.
conditioned coming in contact with the conditioning surface.
Of these statements: tas
(a) I and III are correct (b) I and II are correct
(c) III alone is correct (d) II alone is correct
101. Ans. (b)
102. The by-pass factor of single cooling coil in an air-conditioner is 0.7. The by-pass
lda
factor, if three such cooling coils with the same apparatus dew point are kept one behind
the other will be
(a) 0.210 (b) 0.292 (c) 0.343 (d) 0.412 [IES-2001]
102. Ans. (c)
103. By pass factor for a cooling coil [IES-1992]

vi
(a) increases with increase in velocity of air passing through it

(b) decrease with increase in velocity of air passing through it
(c) remains unchanged with increase in velocity of air passing through it
Ci
(d) may increase or decrease with increase in velocity of air passing through it
depending upon the condition of air entering.
103. Ans. (a)
w.
Air Washer
Air washer can work as
ww
1. Humidifier only 2. Dehumidifier only 3. Filter only

Which of the statements given above is/are correct?
(a) Only 1 (b) Only 2 and 3 (c) Only 1 and 3 (d) 1, 2 and 3
104. Ans. (c)
105. Air at dry bulb temperature of 35°C and dew point temperature of 25°C passes
through an air washer whose temperature is maintained at 20°C. What is the nature of
the process involved? [IES-2005]
(a) Cooling and humidification (b) Sensible cooling
(c) Heating and dehumidification (d) Cooling and dehumidification

105. Ans. (d)
106. Air (at atmospheric pressure) at a dry bulb temperature of 40°C and wet bulb
temperature of 20°C is humidified in an air washer operating with continuous water
recirculation. The wet bulb depression (i.e. the difference between the dry and wet bulb
temperatures) at the exit is 25% of that at the inlet. The dry bulb temperature at the exit
of the air washer is closest to [GATE-2008]
(A) 100C (B) 200C (C) 250C (D) 300C
m
106. Ans. (C)
107. In a spray washing system, if the temperature of water is higher than the dry bulb
co
temperature of entering air, then the air is [IES-1993]
(a) heated and dehumidified (b) heated and humidified
(c) cooled and humidified (d) cooled and. dehumidified
107. Ans. (b)
.
108. Two steams moist air ‘1’and ‘2’mix together stream of unsaturated air ‘3’, Let ‘m’
tas
denote the rate of total mass flow of moist air, ‘m ω ’denote the rate of mass flow of
associated water vapour, ‘ ω ’denote the specific humidity and ‘t’ the temperature
of a stream. Then ‘t3’ the temperature of stream ‘3’ will be [IAS-1995]
(a)
( m1 − mω 2 ) ω1t1 + ( m2 − mw2 ) ω2t2 (b)
( m1 − mω 2 ) t1 + ( m2 − mw2 ) t2
( m3 − mω 3 ) ω3 ( m3 − mω1 )
lda
ω1t1 + ω2t2 m1ω1t1 + m2ω2t2
(c) (d)
ω2 m2ω3
108. Ans. (b)
vi
Air Conditioning
109. For an air-conditioned space, RTH = 100 kW, RSHF = 0.75, volume flow rate =
Ci
100m3/min, and indoor design specific humidity is 0.01 kg/kg of dry air. What is the
specific humidity of the supply air? [IES-2005]
(a) 0.010 (b) 0.0075 (c) 0.005 (d) 0.0025
RLH 25
109. Ans. (c) ( Cmm )s,min = or 100 = or (ωi − 0.01) = 0.005
w.
50 (ωi − ωADP ) 50 (ωi − 0.01)

⎡ RSH RSH ⎤
⎢∵ RSHF = RTH = RSH + RLH ⎥
⎣ ⎦
ww

1. If air is heated in a closed chamber, its dew point will increase
2 As relative humidity decreases, the difference between the wet-bulb temperature and
dew point will increase
3. In spray humidification process, the enthalpy of air will decrease
4. The dew-point temperature is always an indication of moisture content of the air
(a) 1 and 2 (b) 2 and 4 (c)1 and 3 (d) 3 and 4
110. Ans. (b)
1. As no moisture is added so no change in dew point.

2. (tw1 – td1) < (tw2 – td2)
m
co
3. By energy balance it increases not decreases because it added water’s enthalpy h2 =
h1 + (ω2 − ω1 ) hf
4. See above graph
.
So 2 & 4 are correct
tas
111. Air-conditioning has to be done for a hall whose RSH = 50 kW and RLH = 50 kW.
There are no other sources of heat addition or leakages. What is the value of the RSHF?
(a) 0.25 (b) 0.5 (c) 0.75 (d) 1.00 [IES-2005]
RSH 50
111. Ans. (b) RSHF = = = 0.5
lda
RSH + RLH 50 + 50

When a GSHF line is extended, it may strike the saturation curve at a point. This point is
called
1. effective surface temperature. 2. air saturation temperature.
vi
3. water boiling temperature. 4. apparatus dew point.

112. Ans. (b)
Ci
113. In the case of a cooling coil with non-zero bypass factor, the apparatus, dew point
temperature lies at the intersection point of [IAS-1997]
(a) room DB line with the saturation curve (b) RSHF and GSHF lines
w.
(c) RSHF and ESHF lines (d) GSHF line with the saturation
curve
113. Ans. (d)
114. The state of air supplied by a cooling coil with a by-pass factor X lies on the
ww
psychometric chart at the [IAS-1998]

(a) intersection of RSHF line with saturation curve
(b) intersection of GSHF line with saturation curve
(c) point which divides RSHF line in proportion to X and (1 - X)
(d) point which divides ESHF line in proportion to X and (I-X)
114. Ans. (d)
115. Fresh air intake (air change per hour) recommended for ventilation purposes in the
air-conditioning system of an office building is [IES-1997]
(a) 1/2 (b) 3/2 (c) 9/2 (d) 25/2

115. Ans. (c)
116. In aircraft, air refrigeration cycle is used because of [IES-1995]

(a) low unit weight per tonne of refrigeration (b) high heat transfer rate.
(c) lower temperature at high-altitudes (d) higher coefficient of performance.
116. Ans. (a)
117. Consider the following statements related to all-air air-conditioning system:
m
1. All air system uses air as heating or cooling fluid. [IAS-2007]
2. When hot air is circulated through rooms, dehumidification is necessary to control
relative humidity.
co
3. Return air ducts are required for recirculation.
(a) 1, 2 and 3 (b) 1 and 2 only (c) 1 and 3 only (d) 2 and 3 only
117. Ans. (c)
.
118. Assertion (A): Dehumidification and humidification respectively are needed in winter
tas
and summer air-conditioning. [IES-1994]
Reason (R): In winter, the air is to be heated and in summer, the air is to be cooled and
moisture control is necessary to maintain the relative humidity within limits.
118. Ans. (a) Both A and R are true and R provides correct explanation for A.
lda
119. Moist air at a pressure of 100 kPa is compressed to 500 kPa and then cooled to
350C in an after cooler. The air at the entry to the after cooler is unsaturated and
becomes just saturated at the exit of the after cooler. The saturation pressure of water at
35°C is 5.628 kPa. The partial pressure of water vapour (in kPa) in the moist air entering
the compressor is closest to [GATE-2008]
(A) 0.25 (B) 0.5 (C) 0.75 (D) 1
vi
119. Ans. (B) Volume change is one fifth and water vapour just compressed to one fifth
5.628
volume so unsaturated vapour pressure= = 1.1256
5
~
Ci
− 1.13kPa
w.
ww
m
. co
tas
vi lda
Ci
w.
ww
Air refrigeration system
m
Boot-strap
Simple evaporative
co
Regenerative
Boot-strap evaporative
1. Which is the most suitable type of air refrigeration system for supersonic planes with
.
Mach Number 3 or above? tas [IES-2005]
(a) Boot-strap (b) Simple evaporative
(c) Regenerative (d) Boot-strap evaporative
1. Ans. (d) Actually for this use Reduced Ambient system of refrigeration.
Comfort
lda
2. In a system: Metabolic rate = M, work done by man = W, rate of convective, radiative
and evaporative heat losses = Q and rate of heat storage = S. Then heat exchange
between man and his environment is given by [IES-2002]
(a) M + W = Q + S (b) M - W = Q - S
(c) M + W = Q – S (d) M - W = Q + S
2. Ans. (d)
vi
3. A human body feels comfortable when the heat produced by the metabolism of
human body is equal to [IES-2006]
Ci
(a) Heat dissipated to the surroundings (b) Heat stored in the human body
(c) Sum of (a) and (b) (d) Difference of (a) and (b)
3. Ans. (c)
4. A human body feels, comfortable when the heat produced by the metabolism of
w.
human body is equal to the [IES-1993]

(a) heat dissipated to the surroundings (b) heat stored in the human body
(c) sum of (a) and (b) (d) difference of (a) and (b)
4. Ans. (a)
ww
5. A passive method to keep the house comfortably warm by solar conditioning in cold
climatic condition is to paint the: [IES-2005]
(a) Eastern wall of the house by black paint on its outer side
(b) Eastern wall of the house by back paints on its inner side
(c) Southern wall of the house by black paint on its outer side
(d) Southern wall of the house by black paint on its inner side
5. Ans. (b)
6. On which factor(s), does the heat lost by the human body in the process of radiation
depend? [IES-2005]
(a) Temperature only (b) Temperature and air motion
(c) Temperature and relative humidity (d) Relative humidity and air motion
6. Ans. (a)
7. Which of the following are normally desired comfort conditions in an air-conditioning

system? [IES-2004]
(a) 25°C DBT and 50% RH (b) 22°C DBT and 90% RH
m
(c) 15°C DBT and 75% RH (d) 15°C DBT and 40% RH
7. Ans. (a)
co
8. The desirable air velocity in the occupied zone for comfort for summer air-conditioners
is in the range of [IES-2000]
(a) 6 - 7 m/minute (b) 4 - 5 m/minute (c) 2 - 3 m/minute (d) 0.5 - 1.5 m/minute
8. Ans. (d)
.
9. A human body feels comfortable when the heat produced due to metabolism of
tas
human body is equal to the [IES-1999]
(a) heat dissipated to the surroundings (b) heat stored in human body
(c) difference between heat dissipated to the surroundings and heat stored in human
body
(d) sum of heat dissipated to the surroundings and heat stored in human body
lda
9. Ans. (a) A human body feels comfortable when heat produced due to metabolism of
human body gets equal to the heat dissipated to the surroundings.
10. The reason for a person feeling more comfortable on a warm day if seated in front of
an electric fan is that the [IES-1999]
(a) metabolic heat production is reduced
vi
(b) body loses more heat by convection and evaporation

(c) body loses more heat by radiation
(d) body loses more heat by evaporation and radiation
10. Ans. (b)
Ci
11. On a summer day, a scooter rider feels more comfortable while on the move than
while at a stop light because
(a) an object ill motion captures less solar radiation. [IES-1998]
w.
(b) air is transparent to radiation and hence it is cooler than the body.
(c) more heat is lost by convection and radiation while in motion
(d) Air has a low specific heat and hence it is cooler.
11. Ans. (a) A body in motion captures less solar radiation.
ww
12. Assertion (A): The actual inside design temperatures selected in comfort air-
conditioning are not necessarily those conditions of optimum comfort.
Reason (R): The length and type of occupancy, the outside design conditions and
economic factors affect the choice. [IAS-2001]
12. Ans. (a)
13. In room air-conditioning for comfort, the supply air in summer should be at
(a) the same temperature as that of the room
(b) 5 to 10° C below the room temperature [IAS-1997]
(c) 2 to 30C above the room temperature (d) at 0° C

13. Ans. (b)
14. What are the general comfort conditions in an air-conditioning system?

(a) 20oC DBT, 80% RH (b) 24 oC DBT, 60% RH [IES-2006]
(c) 25oC DBT, 40% RH (d) 25 oC DBT, 100% RH
14. Ans. (b)
15. Which of the following statements are correct?
m
[IES-1994]
1. The human body can lose heat even if its temperature is less than the atmospheric
temperature.
2. Relative humidity can be increased by cooling and dehumidification.
co
3. Warm air increases the rate of radiation of heat from the human body.
4. Increase in air movement increases the evaporation from the human body.
Codes: (a) 1 and 4 (b) 2 and 4 (c) 1 and 3 (d) 2 and 3
15. Ans. (a)
.
16. The difference between the comfort airconditioning and industrial airconditioning lies
tas
in the [IAS-1998]
(a) equipment used (b) process adopted
(c) indoor requirements (d) ambient conditions
16. Ans. (c)
lda
17. Effective temperature depends on dry bulb temperature, and [IES-2006]
(a) Wet bulb temperature only (b) Relative humidity
(c) Specific humidity (d) Wet bulb temperature and air motion
17. Ans. (d)
vi
18. Dry bulb temperature and wet bulb temperature is 25°C each, and velocity of air
passing over human body is 6 m/min. If velocity increases to 20 m/min, then which one
Ci
of the following is correct? [IES-2006]

(a) The effective temperature decreases
(b) The effective temperature remains the same
(c) The effective temperature increases
(d) The change in effective temperature cannot be estimated with the given information
w.
18. Ans. (a) Any activity which increase human comfort will reduce effective
temperature.
Alternatively: Rydberg and Norback equation gives us difference
Δ t = (t – 24.4) – 0.1276 (C – 9.1)
t = local temperature, oC; C = local velocity m.p.m
ww
if t is constant and C increases from 6 to 20 m/min

Δ t =– 0.1276 (6 – 20) = - 1.8 oC

The optimum effective temperature for human comfort is:
(a) higher in winter than that in summer (b) lower in winter than that in summer
(c) same in winter and summer (d) not dependent on season
19. Ans. (b)

(a) Effective temperature is the index which the correlates combined effects of air dry
bulb temperature, air humidity and air movement upon human comfort
(b) The value of effective temperature in winter and summer should be same for human
comfort
(c) Effective temperature and wet bulb temperature are one and the same
(d) The value of effective temperature should be higher in winter than In summer for
comfort
m
20. Ans. (a)
21. Upon which of the following factors does the effective temperature for human
co
comfort depend? [IES-2003]
1. Dry bulb temperature 2. Humidity ratio
3. Air velocity 4. Mean radiation temperature
(a) 1 and 2 (b) 1, 3 and 4 (c) 2, 3 and 4 (d) 1, 2, 3 and 4
.
21. Ans. (d) tas
22. Assertion (A): Effective temperature, an index of comfort, is defined as that
temperature of saturated air at which one would experience the same feeling of comfort
as experienced in the actual environment. [IES-2001]
Reason (R): Comfort does not depend on humidity and air velocity.
lda
22. Ans. (c)
23. Consider the following parameters: [IES-2000]

1. Dry-bulb temperature 2. Humidity ratio
3. Air velocity 4. Solar radiation intensity
Which of these parameters are taken into account for determining effective temperature
vi
for human comfort?

(a) 1 and 2 (b) 1 and 4 (c) 2, 3 and 4 (d) 1, 2 and 3
23. Ans. (d)
Ci
24. The effective temperature is a measure of the combined effects of

(a) dry bulb temperature and relative humidity (b) dry bulb temperature and air
motion
(c) wet bulb temperature and air motion [IES-1998]
w.
(d) dry bulb temperature, relative humidity and air motion

24. Ans. (d) The effective temperature is the combined effect of dry bulb temperature,
relative humidity and air motion.
25. Effective temperature is that temperature of saturated air which gives the same
ww
degree of comfort as the air at given [IES-1993]

(a) DBT, WBT and incidental solar radiation
(b) WBT, incidential solar radiation and air flow rate
(c) DBT, sol-air temperature and air flow rate (d) DBT, WBT and air flow rate
25. Ans. (d)
26. Which one of the following statements is true for effective temperature, ET?
(a) ET increases with increase in level of activity and it decreases with increase in air
velocity [IAS-2004]
(b) ET decreases with increase in level of activity and it increases with increase in air
velocity.
(c) ET increases with increase in level of activity and it increases with increase in air
velocity
(d) ET decreases with increase in level of activity and decreases with increase in air
velocity.
26. Ans. (c) Rule: Any activity which reduces comfort will increase ET.
m
[IAS-1999]
Effective temperature is NOT a true comfort index because
L discomfort may be experienced at extremely high or low humilities.
2, the radiation effect of surrounding surfaces has not been taken into account.
co
3. it presumes the absence of drafts.
(a) 1, 2 and 3 are correct (b) 1 and 2 are correct
27. Ans. (b)
.
tas
1. Is a measure of the sensation of warmth or coldness. [IAS-1996]

2. Is the uniform temperature of an imaginary enclosure with which man will exchange
the same dry heat by radiation and connection as in the actual environment.
lda
3. Combines the effects of dry bulb temperature, wet bulb temperature and air
movement.
(a) 1 and 2 are correct (b) 1 and 2 are correct(c) 2 and 3 are correct (d)1 and 3
are correct
28. Ans. (a)
vi
29. A room air is at a DBT of Tr and relative humidity φ r . The effective temperature of
the room is
Ci
(a) the temperature at which the room air is saturated but gives the same feeling of
comfort as the actual state of the room air [IAS 1994]
(b) the temperature at which the room air is at 50% relative humidity but gives the same
feeling of comfort as the actual state of the room air
(c) the temperature at which the room air is completely dry but gives the same feeling of
w.
comfort as the actual state of the room air.

(d) none of the above
29. Ans. (a)
ww
Load calculation
30. The heat load from the occupants in air-conditioning load calculation is a source of:
(a) Sensible heat only (b) Latent heat only [IES-2006]
(c) Both sensible and latent heat (d) None of the above
30. Ans. (c)
31. An air-conditioned room of volume 10 m3 has infiltration of air equivalent to 3 air

changes per hour. Density of air is 1.2 kg/m3, specific heat cp is 1 kJ/kg K and
temperature difference between room and ambient air is 20 K. What is the sensible heat
load due to infiltrated air? [IES-2005]
(a) 60 kJ/hour (b) 12 kJ/hour (c) 0.45 kW (d) 0.2 kW
⎧⎛ 10 × 3 ⎞ ⎫
31. Ans. (d) Q = mc p Δt = ⎨⎜ ⎟ × 1.2⎬ × 1× 20 = 0.2kW
⎩⎝ 3600 ⎠ ⎭
32. In an air-conditioning plant the refrigeration load on the coil is 100 TR The mass and
m
enthalpy of air leaving the coil are 420 kg/minute and 40 kJ/kg respectively. What will be
the enthalpy of the air at the Inlet to the coil under these conditions? [IES-2004]
(3) 80 kJ/kg (b) 90 kJ/kg (c) 100 kJ/kg (d) 102.5 kJ/kg
co
32. Ans. (b) ∴ Q = m1 ( h1 − h2 )
Q 100 × 210kJ / min
or h1 = h2 + = 40 + = 90 kJ / kg
m1 420 kg / min
.
tas
lda
33. Moist air enters the cooling coil with mass flow rate of 10 kgda/s at dry bulb
temperature of 30oC and humidity ratio of 0.017 kgw/kgda. It leaves the cooling coil at
dry bulb temperature of16oC and humidity ratio of 0.008 kgw/kgda. If specific heat of
humid air is 1.02 kJ/kgda-K and latent heat of water vapour is 2500 kJ/kgw. The sensible
and latent heat transfer of cooling coil are, respectively [IES-2003]
vi
(a) 140 kW and 25000 kW (b) 142.8 kW and 2.25 kW

(c) 142.8 kW and 225 kW (d) 225 kW and 142.8 kW
33. Ans. (c) We know that humid specific heat, Cp = Cpa+ωCpv = 1.02 KJ/kgda.K
Therefore, Sensible heat load (SHL) = ma C p ( ΔTdb ) = 10 × 1.02 × (30 − 16) = 142.8kW
Ci
( )
and Latent heat load (LHL) = ma (ωi − ωo ) h fg = 10 × ( 0.017 − 0.008 ) × 2500 = 225 kW
34. Atmospheric air at a flow rate of 3 kg/s (on dry basis) enters a cooling and
w.
dehumidifying coil with an enthalpy of 85 kJ/kg of dry air and a humidity ratio of 19
grams/kg of dry air. The air leaves the coil with an enthalpy of 43 kJ/kg of dry air and a
humidity ratio 8 grams/kg of dry air. If the condensate water leaves the coil with an
enthalpy of 67 kJ/kg, the required cooling capacity of the coil in kW is [GATE-2007]
(a) 75.0 (b) 123.8 (c) 128.2 (d) 159.0
ww
34. Ans. (b)
35. An air-conditioned room has length, width and height of 20 m, 30 m and 4 m

respectively. The infiltration is assumed to be one air change. The outdoor and indoor
dry bulb temperatures are 40oC and 25oC respectively. The sensible heat load due to
infiltration is [IES-2003]
(a) 734 kW (b) 12.24 kW (c) 0.204 kW (d) 10 kW
20 × 30 × 4 3
35. Ans (b) Infiltration ‘1’ air change per hour, i.e., (cmm) = m / min
60
[(cmm) = volumetric flow rate cubic meter per minute]
⎛ 20 × 30 × 4 ⎞
1.2 × (cmm) × C p × ( Δt )
1.2 × ⎜ ⎟ × 1.02 × ( 40 − 25 )
⎝ 60 ⎠
Qs = = kW = 12.24kW
60 60
m
36. For an office building the outdoor design conditions are 45°C dbt and humidity ratio
of 0.015. The indoor design conditions are 25°C dbt and 0.01 humidity ratio. The supply
air state is 15°C dbt and 0.007 humidity ratio. If the supply air flow rate is 1000 m3/ min
and fresh air flow rate is m3/ min, room sensible and room latent heat loads are,
co
respectively,
(a) 408 kW and 400 kW (b) 408 kW and 150 kW [IES-2002]
(c) 204 kW and 400 kW (d) 204 kW and 150 kW
36. Ans. (d)
.
37. For an air-conditioning system, the outdoor and indoor design dry bulb temperatures
tas
are 45°C and 25°C respectively. The space to be air-conditioned is 20 m x 30 m X 5 m
and infiltration is estimated to be one air change. If the density and specific heat of air
are 1.2 (kg of dry air)/m3 and 1.02 kJ/(kg of dry air)°C, then the sensible heat load due to
infiltration is, nearly [IES-2001]
(a) 122.4 kW (b) 61.2 kW (c) 12.24 kW (d) 2004 kW
lda
37. Ans. (d)
38. For an-conditioned space, RTH = 100 kW; RSHF = 0.75, volume flow rate is equal to
100 m3/minute and indoor design specific humidity is 0.01 kg/(kg of dry air). The specific
humidity of supply air is [IES-2001]
(a) 0.010 (b) 0.0075 (c) 0.005 (d) 0.0025
vi
38. Ans. (c)

1. The recommended outside air required per person for an auditorium is
Ci
approximately 0.25 m3/min.

2. Outside air for ventilation purposes causes sensible heat load and also latent
heat load.
3. The sensible heat factor for an auditorium is generally kept as 0.7
w.

39. Ans. (c)
40. An air-conditioned room of volume 10 m3 has infiltration of air equivalent to 3 air

ww
changes. Density of air is 1.2 kg/m3, specific heat Cp is 1 kJ/kg-K and temperature
difference between room and ambient air is 20 K. The sensible heat load due to
infiltrated air is [IES-2000]
(a) 60 kJ/hr (b) 12 kJ/hr (c) 6 kW (d) 0.2 kW
40. Ans. (d)
41. The sensible heat factor of a room is given by (S.H.L = Sensible heat load and L.H.L.
= Latent heat load) [IES-1999]
S .H .L − L.H .L S .H .L S .H .L + L.H .L S .H .L
(a ) (b) (c) (d)
S .H .L S .H .L − L.H .L S .H .L S .H .L + L.H .L
S .H .L
41. Ans. (d) SHF =
S .H .L + L.H .L
42. In air-conditioning design for summer months, the condition inside a factory where
heavy work is performed as compared to a factory in which light work is performed
should have
m
(a) lower dry bulb temperature and lower relative humidity [IES-1998]
(b) lower dry bulb temperature and higher relative humidity
(c) lower dry bulb temperature and same relative humidity
co
(d) same dry bulb temperature and same relative humidity
42. Ans. (d) Air conditioning parameters are same for all conditions of loading. Air
conditioning capacity has to be designed for the heat load to maintain the parameters
43. Two summer air-conditioning systems with non-zero by pass factor are proposed for
.
a room with a known sensible and latent heat load. System A operates with ventilation
tas
but system B operates without ventilation. Then the [IES-1995]
(a) bypass factor of system A must be less than the bypass factor of system B
(b) bypass factor of system A must be more than the bypass factor of system B
(c) apparatus dew point for system A must be lower than the apparatus dew point for
system B
lda
(d) apparatus dew point for system A must be higher than the apparatus dew point for
system B.
43. Ans. (c)
44. Consider the following factors: [IES-1994]

1. Wind velocity 2. Type of activity 3. Indoor design conditions 4. Door openings
vi
Occupancy load in cooling load calculations depends upon

(a) 1 and 2 (b) 1 and 3 (c) 1 and 4 (d) 2 and 3.
44. Ans. (d) Occupancy load in cooling load calculation depend upon type of activity and
indoor design conditions.
Ci
Solar refrigeration
45. What is Sol-air temperature? [IES-2006]
(a) It is equal to the sum of outdoor air temperature, and absorbed total radiation divided
w.
by outer surface convective heat transfer coefficient

(b) It is equal to the absorbed total radiation divided by convective heat transfer
coefficient at outer surface
(c) It is equal to the total incident radiation divided by convective heat transfer coefficient
at outer surface
ww
(d) It is equal to the sum of indoor air temperature and absorbed total radiation divided
by convective heat transfer coefficient at outer surface
αI
45. Ans. (a) sol-air temperature te = to +
ho
Rate of heat transfer from outside to wall is qo ∴qo = ho (to − t s ) + α I = ho (te − ts )
For heat transfer through building structure the sol-air temperature is used instead of
conduction and solar radiation separately.
46. A thin flat plate 2m by 2m is hanging freely in air. The temperature of the
surroundings is 25°C. Solar radiation is falling on one side of the rate at the rate of 500
W/m2. The temperature of the plate will remain constant at 30°C, if the convective heat
transfer coefficient (in W/m2oC) is
(a) 25 (b) 50 (c) 100 (d) 200 [IES-1993]
46. Ans. (a) Heat transfer by convection Q = hAΔt
or 500 × (2 × 2) = h × (2 × 2) × ( 30 − 25 ) or h = 100W / m 2 oC
m
47. Assertion (A): Solar Radiation is mainly scattered or transmitted but not absorbed by
the atmosphere. [IES-1992]
co
Reason (R): Absorptivity of atmosphere is low.
47. Ans. (a)
48. A thin flat plate 2 m x 2 m is hanging freely in air. The temperature of the
surroundings is 25°C. Solar radiation is falling on one side of the plate at the rate of 500
.
W/m2. What should be the convective heat transfer coefficient in W/m2oC if the
(a) 25 (b) 50
tas
temperature of the plate is to remain constant at 30oC?
(c) 100
48. Ans. (b) Heat absorbed = heat dissipated or G.A = h × ( 2A ) × Δt
(d) 200
[IES-2005]
500
or 500 = h × 2 × (30 − 25) or h = = 50 W / m2 .k
2×5
lda
49.
vi
Ci
w.
Solar energy is absorbed by the wall of a building as shown in the above figure.
Assuming that the ambient temperature inside and outside are equal and considering
steady-state, the equivalent circuit will be as shown in
(Symbols: Rco = Rconvection,outside RCI = Rconvection,inside and Rw = RWall) [IES-1998]
(a) (b)
ww
(c) (d)
49. Ans. (a) All resistances are in series.
50. A solar collector receiving solar radiation at the rate of 0.6 kW/m2 transforms it to the
internal energy of a fluid at an overall efficiency of 50%. The fluid heated to 350 K is
used to run a heat engine which rejects heat at 313 K. If the heat engine is to deliver 2.5
kW power, then minimum area of the solar collector required would be [GATE-2004]
(a) 8.33 m2 (b) 16.66 m2 (c) 39.68 m2 (d) 79.36 m2
50. Ans. (d)

Let area be A ∴ heat received(G) = 0.6A kW
and power given to the fluid(Q) = G × ε = 0.6A × 0.5 = 0.3A kW
313
Maximum efficiency is Carnot Efficiency (η ) = 1 − = 0.10571
350
Power deliver (W ) = Q × η
Or 2.5 = 0.3A × 0.10571 or A = 79.36m2
m
51. Assertion (A): In an air-conditioned room, the reflective coating should be on the
inside of the window.
Reason (R): Window pane glass is transparent to solar radiation. [IES-1996]
co
51. Ans. (d) A is false but R is true
.
Duct Design tas
52. Consider the following statements pertaining to duct design: [IES-2006]
1. Aspect ratio of ducts should be high.
2. In the equal friction, method of design, use of dampers cannot be eliminated by
any means.
3. The static regain method is not suitable for long ducts.
lda
4. The velocity reduction method is employed only in simple systems.
52. Ans. (b)
53. Which one of the following statements is true for air conditioning duct design?
vi
(a) Static regain method is used, when the duct work is extensive, total pressure drop is
low and flow is balanced
(b) Static regain method is used, when the duct work is extensive, total pressure drop is
high and flow is unbalanced
Ci
(c) Equal friction method is used, when the duct work is extensive, total pressure drop is
low and flow is balanced
(d) Equal friction method is used, when duct work is extensive, total pressure drop is low
and flow is unbalanced [IES-2001]
w.
53. Ans. (c)
54. If coefficient of contraction at the vena contracta is equal to 062, then what will be
the dynamic loss coefficient in sudden contraction in air-conditioning duct? [IES-2004]
(a) 025 (b) 0375 (c) 0.55 (d) 065
ww
2 2
⎛ 1 ⎞ ⎛ 1 ⎞
54. Ans. (b) K=⎜ − 1⎟ = ⎜ − 1⎟ = 0.375
C
⎝ c ⎠ ⎝ 0.62 ⎠
55. Consider the following statements in respect of the contraction and expansion in air
conditioning ducts: [IES-2003]
1. Pressure drop is more in contraction than in expansion.
2. Pressure drop is more in expansion than in contraction.
3. Static pressure increases (regain) in expansion.
4. Static pressure increases (regain) in contraction.

(a) 1 and 2 (b) 1, 2 and 3 (c) 1 and 3 (d) 2 and 4
55. Ans. (c)

The typical air velocities in the ducts of air-conditioning systems are
1. lower in residential buildings as compared to those of public buildings
2. higher in residential buildings as compared to those of public buildings
m
3. higher in industrial buildings as compared to those of public buildings
4. equal in all types of buildings
co
(a) 1 alone (b) 1 and 3 (c) 2 and 3 (d) 4 alone
56. Ans. (b)
57. Which of the following method (s) is/are adopted in the design of air duct system?
1. Velocity reduction method 2. Equal friction method 3. Static regain method.
.
tas [IES-1998]
Codes:
(a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
57. Ans. (c)
58. The most commonly used method for the design of duct size is the [IES-1996]
lda
(a) velocity reduction method (b) equal friction method.
(c) static regain method (d) dual or double duct method.
58. Ans. (a) The most commonly used method for the design of duct size is the velocity
reduction method
59. The equivalent diameter (D) of a circular duct corresponding to a rectangular duct
vi
having longer side 'a' and shorter side ‘b', for the same velocity and pressure drop is
given by [IES-1994]
a+b ab a+b 2ab
(a) D = (b) D = (c) D = (d) D =
a+b a+b
Ci
ab 2ab
59. Ans. (d)
60. Which of the following items related to infiltration of outdoor air in an air-conditioning
system, are correctly matched? [IAS-2007]
w.
1. Stack effect : Height of building

2. Crack length method : Wind velocity
3. Air change method : Floor area
4. Door opening : Occupancy in kitchen
ww

60. Ans. (a)
the lists:
List I (Material) List II (Purpose/application)
A. Glass wool 1. Cold storage
B. Ammonia 2.Domesticrefrigerators
C G.I. Sheet 3. Insulation

D. Polyurethane 4. Ducting[IAS-1995]
(a) 3 1 4 2 (b) 3 3 4 1
(c) 1 3 4 2 (d) 3 1 2 4
61. Ans. (a)
62. Which one of the following statements is correct? [IAS-1995]

(a) The sensible heat gain is due to the difference in humidity
m
(b) The latent heat gain is due to the temperature difference between the fresh air
through unconditioned space in the building adds to the sensible heat gain
(c) The heat gain through the walls of ducts carrying conditioned air through
co
unconditioned space in the building adds to the sensible heat gain
(d) Maximum heat gain to a building occurs through walls
62. Ans. (c)
63. For air-conditioning the operation theatre in a hospital, the percentage of outside air
.
in the air supplied is tas
(a) zero (b) 20 (c) 50 (d) 100 [IAS-1995]
63. Ans. (d) It is advisable to recalculate infected air of operation theatre and
accordingly % age of outside air is 100%.
Statement for Linked Answer Questions 64 and 65:

lda
An un-insulated air conditioning duct of rectangular cross section 1m x 0.5 m, carrying
air at 20°C with a velocity of 10 m/s, is exposed to an ambient of 30°C. Neglect the effect
of duct construction material. For air n the range of 20-30°C, data are as follows: thermal
conductivity = 0.025W/mK: velocity = 18 µPas; Prandtl number = 0.73; density = 1.2
kg/m3. The laminar flow Nusselt number is 3.4 for constant wall temperature conditions
and, for turbulent flow, Nu = 0.023 Re0.8Pr0.8
vi
64. The Reynolds number for the flow is [GATE-2005]

(a) 444 (b) 890 (c) 4.44 x 105 (d) 5.33 x 105
64. Ans. (c)
Ci
ρ vD ⎡ 4A c 4 × 1× 0.5 ⎤
Re = , ⎢D = = = 0.6667 ⎥
μ ⎢⎣ P 2 (1 + 0.5 ) ⎥⎦
1.2 × 10 × 0.6667
Or R e = = 4.444 × 105
18 × 10 −6
w.
65. The heat transfer per metre length of the duct, in watts, is [GATE-2005]
(a) 3.8 (b) 5.3 (c) 89 (d) 769
65. Ans. (d)
ww
Nu = 0.023 × (R e ) × ( 0.73 )
0.8 0.33
= 683.72
hD 683.72 × 0.025
Nu = or h = = 25.64
k 0.6667
Q = hA ( t h − t c ) = 25.64 × 2 × (1 + 0.5 ) × 1× ( 30 − 20 ) = 769 W / m
66. Instantaneous cooling loads are NOT equal to instantaneous heat gains because
(a) Heat gains are offset by cooling provided by the AC system [IES-2003]
(b) Indoor temperatures are lower
(c) Comfort conditions are maintained in the space

(d) Of the storage effect in the construction material of walls and roof
66. Ans. (d)
m
. co
tas
vi lda
Ci
w.
ww
m
. co
tas
vi lda
Ci
w.
ww

Refrigeration and Air-Conditioning - S K Mondal 1

Uploaded by

Copyright:

Available Formats

Refrigeration and Air-Conditioning - S K Mondal 1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Refrigeration and Air-Conditioning - S K Mondal 1

Uploaded by

Copyright:

Available Formats

Visit : www.Civildatas.

Volumetric Efficiency of reciprocating Compressors

Heating and dehumidification

Air refrigeration system

reservoir at 600 K. The coefficient of performance is [IES-1999]

11. A heat pump is shown schematically as [IES-1994]

And heat rejected = refrigeration effect + work input

or refrigeration effect = 4 x 1kW = 4kW

(a) 180 kW (b) 30 kW (c) 6 kW (d) 5 kW

16. In the system given above, the temperature T =

300 − 150 300 − 150

temperature source. In heat pump we are interested on heat addition to higher

(a) 0.5 (b) 2.0 (c) 28.3 (d) 29.3

28. The coefficient of performance of a refrigerator working on a reversed Carnot cycle is

(a) 6.5 (b) 7.5 (c) 10.5 (d) 15.0 [IES-1997]

30. Ans.(a ) COP =

system per hour if all the losses are neglected? [IAS-2007]

36. The C.O.P. of a Carnot refrigeration cycle decreases on [IAS 1994]

(a) decreasing the difference in operating temperatures

42. If an engine of 40 percent thermal efficiency drives a refrigerator having a coefficient

62. In the above figure, E is a heat engine with

(a) < 0 (b) = 0 (c) > 0 (d) Not sure [GATE-1995]

Production of Solid Ice

(a) Should be near the critical temperature of the refrigerant

52. One ton refrigeration is equivalent to [IES-1999]

54. Ans. (a)

57. A refrigerating machine having coefficient of performance equal to 2 is used to

(a) 1/6 (b) 7/8 (c) 6/7 (d) 1/7

59. Which one of the following statements is correct? [IES-2004]

In refrigerating machines it is the reverse, i.e. (T1 – T2) should be lower.

Reason (R): C.O.P. of refrigeration system decreases with decrease in evaporator

the actual water flow rate? [IES-2005]

Answers with Explanation (Objective)

2. Vapour Compression System

Objective Questions (IES, IAS, GATE)

Vapour Compression Cycle

(i) Enthalpy at exit of the evaporator = 350 kJ/kg [IES-2006]

(a) 0·25 kW (b) 4·0 kW (c) 12·5 kW (d) 11 kW

Compressor work (W) = (

3. The values of enthalpy at the beginning of compression, at the end of compression

4. Replacing a water-cooled condenser with an air-cooled one in a vapour compression

5. In a vapour compression refrigeration plant, the refrigerant leaves the evaporator at

6. Consider the following statements in respect of absorption refrigeration and vapour

1. The former runs on low grade energy.

4. The liquid pump alone replaces compressor of the latter.

7. A standard vapour compression refrigeration cycle consists of the following 4

10. In a vapour compression plant, if certain temperature differences are to be

10. Ans. (c)

(a) evaporator, compressor, condenser and throttle valve [IES-1999]

11. Ans. (c)

12. Consider the following statements: [IES-1998]

1. refrigerant flow is too low 2. water circulation is adequate.

13. Consider the following statements:

In the case of a vapour compression machine, if the condensing temperature of the

16. Consider the following statements: [IES-1995]

1. an increase in refrigerating effect 2. an increase in specific volume of vapour

19. Consider the following statements: [IAS-2007]

very wet vapour.