W i d e Fo r mat Pr i nte r

Te r i o s t a r LP-10 3 0 Se r i e s

Multifunction Model

LP-1030-MF
Printer Model

LP-1030

Quick Reference Guide

U00123009604
 Preface
Your Printer is a Teriostar LP-1030 Series Wide Format Printer.

This manual describes the basic operation methods for both the LP-1030 and LP-1030-MF
models. For more detailed information, see the User's Manuals on the supplied CD-ROM.
Keep this guide in a place where you can easily read it when required.

Table of Contents
Turning the Power On/Off……………………… 3 Operating the Printer from a Computer MF … 25
Power On………………………………………………… 3 Troubleshooting………………………………… 26
Power Off………………………………………………… 3
When an Error Message Appears……………………… 26
Mode Buttons…………………………………… 3 Smears on a Printout………………………………… 26
Replacing the Paper……………………………… 4 Changing the Time Until Power Save Mode………… 26
Automatic Paper Cutting After a Certain Time……… 26
Replacing the Toner Cartridge…………………… 6
Automatic Paper Cutting After Opening
Replacing the Waste Toner Bottle……………… 8 and Closing a Door…………………………………… 27

Replacing the Charger Unit……………………… 10 Changing the Print Density…………………………… 27

Wrinkles on Tracing Paper…………………………… 27
Replacing the Process Cartridge………………… 12
Selecting Paper to Match the Print Data……………… 27
Part Names………………………………………… 14 Missing Print or Slow Data Reception………………… 28

Paper Jams………………………………………… 16 Service Representatives………………………… 31

Disposal Method……………………………………… 31
Copying MF …………………………………… 22

Importing Images (Documents) to a Computer MF … 23

 Turning the Power On/Off
Power On Power Off

1 2 1Press down for

1 sec. or longer

Mode Buttons
zzCOPY button MF
Changes to copy mode, and the lamp at the button's
left lights up. For more details, see the separate User's
Manual for Multifunction Printer Operation.
zzSUBMIT button MF
Changes to submission mode, and the lamp at the
button's left lights up. For more details, see the separate
User's Manual for Multifunction Printer Operation.
zzSCAN button MF
Changes to scan mode, and the lamp at the button's
left lights up. For more details, see the separate User's
Manual for Multifunction Printer Operation.
zzPRINT button
Changes to print mode and enables printing.
zzMENU button
Changes to menu mode, which enables the Printer
setting specification.

3
 Replacing the Paper

1 5

2 6

4
 TT Replacing the Paper

60 cm
(23.63 inches)

ロール紙の交換 1 2 3 4 5 6 7
Replacing Roll Paper
᳈ᤶ㒌ो
用紙カット位置
Paper Cut Position
ߛ㒌ԡ㕂

10

5
 Replacing the Toner Cartridge

1 3

x10
x10

6
 TT Replacing the Toner Cartridge

7 8

Disposing of Empty Toner Cartridges

Put the used toner cartridge into the bag provided in the box of the new toner cartridge, and dispose
of it according to the local regulations.

7
 Replacing the Waste Toner Bottle
x10
1 2

3 ①

8
 TT Replacing the Waste Toner Bottle

5 7

6
①

Disposing of Used Toner Bottles

Dispose of the waste toner bottle according to the local regulations.

9
 Replacing the Charger Unit

1 5
Press down for
1 sec. or longer

3
6

10
 TT Replacing the Charger Unit

8 12

TIP ‘‘ The charger unit can be installed in

either direction.
If lines or other defects appear on
the printout, inverting the charger
unit right and left sides may solve the
problem.

10

11

11
 Replacing the Process Cartridge

1 6
Press down for
1 sec. or longer

7
3

10

11

12
 TT Replacing the Process Cartridge

12 15

13
16

14 17
①

① ②

② ③

18
③

13
 Part Names
Front Side

Multifunction Model

Scanner cover Original output guide

Document table Latch lever

Filter cover

Drawer for roll 1

Waste toner door

Drawer for roll 2

Printer Model

Latch lever

Filter cover

Drawer for roll 1

Drawer for roll 2 Waste toner door

14
 TT Part Names

Rear Side

Multifunction Model Printer Model

Toner door Toner door

Rear door
Rear door

Fuser unit drawer Process cartridge drawer

Paper outlet cover

15
 Paper Jams
The door requiring action is displayed, in
accordance with the paper jam location.
Open the specified door and take the appropriate
action to remove the paper jam.

Paper jam in a Roll paper drawer

1 3
ロール紙の交換 1 2 3 4 5 6 7
Replacing Roll Paper
᳈ᤶ㒌ो
用紙カット位置
Paper Cut Position
ߛ㒌ԡ㕂

16
 TT Paper Jams

Paper jam in the rear door

1 3

17
TT Paper Jams

Paper jam in the Fuser unit

1 3

When you cannot pull out the paper easily:

18
 TT Paper Jams

Paper jam in a roll paper drawer or

front door

1 3

4
2 用紙カット位置
ロール紙の交換
Replacing Roll Paper
᳈ᤶ㒌ो
1 2 3 4 5 6 7

Paper Cut Position

ߛ㒌ԡ㕂

19
TT Paper Jams

Original jam MF

7 1

8 2

20
 TT Paper Jams

21
Copying MF

Press COPY

Set the original

Position the original facing down. Set it in the Printer
aligned with the original width guide. The inserted original
is automatically pulled into the Printer, and set.

22
 Importing Images (Documents) to a Computer MF

Double-click TerioStation.
1

Click the Scan tab.

2

Click Save Folder.

3

Select the destination folder to save the scanned

4 data. Click OK.

Click Scan.
5

23
TT Importing Images (Documents) to a Computer MF

Click Preferences.
6

Input the Printer IP address in the Assign host

7 name/IP address field. Click OK.

Set the scan conditions, and then click Scan.

8

Load the original.

9

Important
‹‹ If "Scanner is operating in another mode" is displayed, press SCAN on the operation panel.
‹‹ If "Color processing is not supported because the scanner being used is a dedicated monochrome
device" is displayed, you cannot scan in color mode.

24
 Operating the Printer from a Computer MF

Start the web browser and enter "http://(IP address set on the Printer)" in the
1 address field. Press Enter.

Click English.
2

Click an item from the left menu to check the settings or Printer status.
3

25
 Troubleshooting

When an Error Message Appears Automatic Paper Cutting After a Certain

Time
Take the action specified by the panel message.
Or see the User's Manual for Basic Printer Operation, Set Top Cut Timer in the Printer Engine menu.
Chapter 5. Menu

Smears on a Printout
Replace the process cartridge. (& page 12) Printer Engine

Changing the Time Until Power Save

Roll 1 Top Cut Timer
Mode
ro
Set Time Before Power Save in the Printer Engine
menu. Roll 2 Top Cut Timer
Menu

Off
or

Printer Engine 30 minutes

or

Time Before Power Save 1 hour

or

15 minutes 2 hours
or
or

30 minutes 4 hours
or
or

60 minutes 1 minute
or
or

90 minutes 5 minutes
or
or

235 minutes 10 minutes

26
 TT Troubleshooting

Automatic Paper Cutting After Opening Wrinkles on Tracing Paper

and Closing a Door
Set Humidity for Tracing Paper to High Humidity
Set Top Cut at Door Open to On in the Printer in the Printer Engine menu.
Engine menu. Menu
Menu

Printer Engine
Printer Engine

Humidity for Tracing Paper

Top Cut at Door Open

High Humidity
On

Selecting Paper to Match the Print Data

Changing the Print Density
Select Optimal at Paper Supply Mode.
Set Print Density in the Printer Engine menu. Menu
Menu

PDL settings
Printer Engine

Select the port and format

Print Density

Paper Parameters
Low
or
Paper Supply Mode
Slightly Low
or
Optimal
Normal
or

Slightly High
or

High

27
TT Troubleshooting

Missing Print or Slow Data Reception Click Change in the operation mode of
Change the driver settings.
4 the driver.
In Start Menu, open Devices and Printers.
1

Change the output process selection from

5 Process with Printer to Process with
Computer. Click OK.

Right-click the OKI LP-1030 icon, and

2 then click Printing Preferences.

Click the Options tab. Click Apply.

3 6

28
 TT Troubleshooting

Click OK.
7 If the problem persists:
Perform steps 1 to 4 and open Driver
1 Operation Mode.

Print.
8 If the symptom persists, perform the
following setting operation.

Set the resolution of the printer driver to

2 200dpi or 100dpi. Click OK.

29
TT Troubleshooting

Click Apply. Click OK.

3 4

Print.
5

The User's Manuals and driver are on the supplied CD-ROM.

30
 Service Representatives

OKI Data Infotech offers support to ensure you get the most from your Teriostar LP-1030 Series Printer.
For details, contact your dealer or nearest service representative.
http://www.okidata-infotech.com/distributors/index.html

Disposal Method

Dispose of the used toner cartridges and waste toner bottles according to the local regulations.

31
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

The CE mark, that shows that the products sold in the EU are conformed to the requirements of EC directive,
is statutorily obliged to be affixed to the products.
In each directive, the scope of directive to be applied to equipment is explicitly defined. Our company’s
product LP-1030 series conforms the EMC directive, low voltage directive and RoHS Directive.

Inquiry of CE mark:

OKI Europe Ltd.

Wide Format Division
Siemensstrasse 9 , D-63263 Neu-Isenburg
Germany
Tel: +49 (0)6102 297 400
Fax: +49 (0)6102 297 50 400

OKI Data Infotech Corporation

8 Nakase 1-chome, Mihama-ku, Chiba-shi, Chiba 261-8507, Japan
Phone : +81 43 211 1363
Fax : +81 43 211 8709

1-8, Nakase, Mihama-ku, Chiba-shi, Chiba, 261-8507, Japan

TEL: (043) 211-1369

U00123009604 December, 2015

Copyright© 2015 OKI Data Infotech Corporation.
All rights reserved.
The contents of this manual may be changed without prior notice.