Basic Kart Setup
Basic Kart Setup
Basic Kart Setup
Here are some changes that can be made to kart setup, and what these changes should do
to the handling of you kart - in theory. There's never one set rule for every chassis for every
track though, so these should only be taken as guidelines. Experimenting with the setup by
yourself and taking note of how the changes affect handling is the best way to find out what
best works for you and your kart. In addition to the kart chassis setup your engine and carb
setting play an important role in your speed. The most important factor however is the nut
behind the wheel - and most attention should go into improving your driving rather than
spending all your time worrying about the kart.
You should really only start to fool around with your kart setup when you can consistently
lap within 2 tenths or so every lap for 10+ lap stints. This way when you make a setup
change you should be confident enough that an improvement in lap time was caused by the
change and not by the driver. Another important point to remember is that you should only
change one thing at a time. If you change two or three factors you will have no idea which
change did what. In last-ditch efforts during race weekends it is of course understandable to
go for several changes at once - when you are way off on the setup.
An important part of setting up a kart is understanding the handling problems. Often drivers
go to try to add grip to the rear of the kart because they are oversteering through a corner.
Closer analysis may however reveal that the oversteer is actually caused by understeer
earlier in the corner. The understeer makes the driver turn the front wheel more than
desired and as the front regains traction the kart snaps into oversteer. It is very important to
think what in your driving may improve the handling of the kart.
The air pressure in the tires is one of the most important things to get right. Starting with
manufacturer recommended pressures is best, and then experimenting with lower or higher
pressures. An important point to remember is that for example 12psi might be absolutely
perfect during your first three laps but your times might quickly start getting worse (often a
sudden .5 tenths per lap slower). This means that your tires were at the optimum pressure
when you started but as tires heat up the pressure builds up and the tires will start
underperforming when the pressure gets higher than optimum. Being fast right out of the
pits is what you need for 3 laps of qualifying, but not for a race.
I find that a good way to find tire pressures that work is by looking at your times. If you are
able to consistently drop your times by a tenth per lap for example over the first five laps
and then your times stabilise or still improve slightly at a slower rate for the next 10 laps you
have found good pressures for a 10-15 lap race. You can try slightly higher pressures until
you reach the point where your times get worse after a few laps.
Generally you would use lower pressures for a long race, high ambient/track temperature,
and when there is a lot of rubber on the track. For the opposite conditions you would
reduce tyre pressure. In wet weather the more water there is on track the more pressure
you should run. On a drying track it is important to run low pressures in wets to prevent
them overheating as much as possible.
Widening the rear track stops the kart from binding as easily and in theory makes the rear of
the kart looser. If your kart is hopping in the corners or you can feel your engine severely
bogging coming out of corners widening the rear track might help (only change rear track
about 10mm each time though).
Going narrower on the rear track in theory makes the kart stick to the track better. So if you
have lots of oversteer narrowing the rear should help.
In general widening the front track should give more front end grip and improve
responsiveness. Narrowing it makes the front end less responsive. Sometimes however it
may feel like the front end needs to be widened out but the front tyres may actually be
overworked and doing the opposite will solve the problem. There is a small difference in
feedback to the driver between the tires being overworked or being underworked - with
time you should be able to distinguish the difference.
Ride Height:
Changing the ride height of your kart makes a big difference to handling. When there isn't a
lot of grip on the track and the kart is sliding all over the place raising the chassis can help a
lot. Normally you would want to run the chassis low for a low centre of gravity to maximise
overall grip. On bumpy street tracks having the chassis higher is a good idea - and on a
street track it’s better to have a kart which binds a little than to have one which slides a lot.
You can also try to change just the front or the rear ride height to affect handling. If you are
experiencing lots of understeer for example you may want to raise the front end and see if
you can generate a bit more front end bite.
For wet weather you would want to set the chassis high if you have the time. Raising the
seat also results in the same result of raising the overall centre of gravity.
Toe-in/out:
Setting the front end alignment is important to have a kart that handles predictably. On
karts you will mainly be looking to have 0mm toe to about 2mm toe-out. Having toe-out will
make the kart more responsive to steering movements and will improve turn-in. The more
your tires are pointing away from dead-ahead however the more rolling resistance you are
introducing. In wet weather you would be looking to run 2mm or more toe to reduce
understeer which is common place because not as much weight is transferred forward
under braking.
Understanding your Chassis
I've read it many times on 4cycle.com about what the optimum setting is for cross. You
don't hear it as much with nose and left side, but the question will pop up. The answer is
that there are no perfect set-up numbers. What must be realized is that each kart and each
driver do not perform the same. Therefore each will require different numbers to perform
to both the kart and the driver’s ability. These numbers may even go outside what the
manufacturer has suggested. The thing that separates the really good drivers form the
mediocre ones is experimentation. These racers use the set-up sheets as a baseline to start
from and tweak the numbers from there. Now the question is how do you find your perfect
numbers? Let me explain.
First you need to understand some things. Setting up a kart is nothing more than a balancing
act. What we are looking for is the perfect balance between forward traction, turning
traction and sideways traction (side bite). If you have too much forward traction, the kart
does not want to turn into the corners. The front of the kart just slides. This is an
understeering (pushing) kart. If the kart has too much turning traction then the rear end of
the kart slides up the track. This is an oversteering (loose) kart. If the kart has too much side
bite it will 'feel' great in the corners but loses speed. This is a binding kart. What is important
to remember right now is that turning traction hurts forward traction and vice versa. Then if
we have too much turning and forward traction then we have a 'binding' kart as well.
What we are looking for is corner speed. Corner speed equals greater straightaway speeds.
This means that we want the maximum amount of forward traction with the least amount
of turning traction that we can get away with in the corners. Too much or too little of one or
the other or even both will slow you down. Let’s look at some things in basic terms.
Nose weight: Nose weight affects how a kart turns. More nose weight equals more turning
traction. Less nose weight is opposite. Too much nose will be loose on entry while too little
will cause a push on entry.
Left side: Left side controls side bite and how much weight is transferred to the right-side
tires. Too much LS will cause a 4-wheeled drift and too little will be tight on entry.
Cross: Cross affects how a kart turns and the distribution of weight transfer. You have varied
opinions on cross. Some say increasing cross loosens the kart while others swear it tightens
the kart. My advice is to experiment with cross and find out how it affects your kart.
Generally too much cross will push on entry while too little will be loose off.
Rear Stagger: Rear stagger affects how well a kart rolls in the corners. More stagger means
that the kart will turn in a tighter circle and less stagger will make the kart turn in a larger
circle. Careful because rear stagger affects straightaway speed.
Front Stagger: Front stagger affects how the kart redistributes weight as the front wheels
are turned. Usually high cross or small tube chassis require less front stagger while low cross
or big tube chassis require more front stagger. More front stagger will reduce cross while
less front stagger will increase cross. Other factors are with camber, especially camber gains
on the RF with steering input. All I'm going to say is try 1 1/4" front stagger then 1 3/4" front
stagger (resetting your numbers) and add steering input. Look at your numbers (nose, LS
and cross) and camber changes compared to both. You will be surprised.
Caster: Generally, more caster equals more front bite, less caster equals less front bite.
There is a lot more to the caster puzzle than this though. I hear this statement a lot: "Caster
is a driver preference adjustment". To me there is way more to the caster game than most
will admit to. Caster sets into motion the rate of weight transfer. Either caster setting will
'unload' the LR. One does it mechanically (LF) while the other does it by nature (RF). Most
will leave the caster settings 'as set by the factory' and few will play with caster. Caster is a
great tool to use to tune the kart. You can generally add bite to the kart by decreasing the
split or by adding caster to both sides. If you increase the split you can take bite out of the
kart. These are very general statements. There is a lot more related to caster than what is
obvious.
Camber: This adjustment has several things tied to it. They are: tire grip and the timing for
weight transfer. This is why changes in camber can drastically change the handling of the
kart. The amount of camber that you need depends on such things as track surface and
configuration, tires, and the amount of cross that you have. Generally high cross set-ups
need -3.0 camber or more. Low cross set-ups need -2.5 or less.
Basically kart setup is a balancing act between turning traction (nose weight), forward
traction (rear weight) and side bite (left side). As discussed above too much forward traction
(rear weight) will cause the kart to push and not enough will cause a kart to be loose. Too
much side bite (low left side) will cause the kart to bind while too little (more left side) will
cause the kart to 4-wheel drift. Too much turning traction (more nose weight) will make the
kart loose while too little (less nose weight) will cause the kart to push. Then we have
probably the most confusing setup number … cross. I don’t know why but people really
confuse themselves with cross. Let’s take a better look at cross.
Cross Weight: You can ask ten different questions on cross and get ten different answers.
I'm going to explain it like this: Cross is NOT a primary adjustment tool. Cross should be used
to fine tune the kart. If your kart is close on setup here is how to adjust cross. I adjust by air
pressure (AP) build up others will adjust using tire temps. If in all cases my RF builds more
AP than the RR then I reduce cross. This will relieve the RF of some of its dynamic loading. If
the RR is building the AP then I increase cross to relieve it of some of its loading. A lot of
what you do will depend on your front-end settings. Generally adding cross decreases the
amount of bite in the kart making it more loose. On the other hand decreasing cross adds
bite to the kart making it want to push. Like I have said before cross can affect your kart
differently depending on your balance (nose vs left side).
I know many race both dirt and asphalt. So what changes do you need to make? Do
anything to take bite out of the kart. That would be to increase left side, cross and RF
camber and reduce caster and nose weight.
Weight Transfer: The amount of weight that transfers is proportional to the height of the
CG, and inversely proportional to the track width of the kart. The following formula will
always hold true: Total Transfer = Total Kart Weight * CG height * Cornering G’s/ Track
Width. We want to minimize weight transfer as much as possible but not to totally eliminate
it; this in turn prevents a decrease in overall traction. Remember that the more loaded a tire
is the more it grips. The amount of weight transferred is also dependent on other factors
like its speed, the radius of the turn and the kart’s path through the turn. The fact that the
amount of weight transferred is proportional to the radius of the turn is one of the reasons
why a large, smooth radius is the fastest line when cornering: it minimizes weight transfer,
so it maximizes overall grip and cornering power.
Obviously, weight transfer has an overall effect on handling: more weight on a tire means
more grip. So, if the CG is located further towards the rear, the kart will have a lot of rear
traction, which is nice to have if acceleration is important. If the CG is located further
towards the front, the kart will have a lot of steering, but it might lack rear traction, which
increases the risk of spinning out. This is the same for lateral weight distribution in LTO karts
except it works left to right. So the CG is very important because it determines the karts roll
characteristics and weight transfer.
The reason we run so much left side weight in LTO karts is to better distribute the weight
when we corner. Asphalt is a little different but not much. The reason we run more left side
on asphalt than we do on dirt is because when we corner we create more G's. Because of
this more left side is needed to counteract the greater side-to-side weight transfer. Same
thing for dirt. When the track is wet/slick we need less left side because the weight is not
going to transfer like it will do when the track is hard/fast. So the more G's we create the
more left side that we need and vice versa.
To a certain extent cross plays a role in dynamic load transfer. Chassis design plays a very
important role in how a kart distributes dynamic loads. Karts are geometrically and
mechanically softer in the front than in the rear. Part of this has to do with CG ‘roll’.
Something to consider is that dynamic weight transfer will always seek the path of least
resistance. Here is an example: due to low lateral acceleration the CG must be able to roll
easily (low front roll stiffness). Low front roll stiffness will make the transition stage
between turn in and keeping the LR unloaded from the effect of horizontal acceleration
easier. All I’m saying is that weight will stay off the LR as the ‘jacking effect’ is coming off,
rather than having the LR ‘reload’ due to excessive front roll stiffness. This is speaking in
terms of a track with low grip. It's opposite for a high grip track.
As a very general rule, entry handling problems can be adjusted at the front-end while exit
problems can be adjusted at the rear end. Usually front-end settings affect how a kart
enters the corner and the rear end affects how a kart exits.
As for tires and air pressure well… there are so many combinations to that puzzle that it is
nearly impossible to cover them all. Not only do you have different combinations of air
pressure, tire compounds and tire manufactures but each person’s setup has an effect on
these combinations as well. The best thing to do is experiment.
This is a very brief explanation of understanding your chassis. I have a manual out that goes
into more detail about how all this stuff effects your kart.
Weight Transfer INTRO
In any discussion of kart handling and setup, "weight transfer" is a term that will always
come up. It is usually used in a general sense, and is almost meaningless without some
additional information. Here is why; on a kart, there are three different ways that weight
shifts from one tire to another.
The purpose of this article is to define each of the three types of weight transfer. With a
better understanding of weight transfer, discussions on kart setup can be more detailed,
and a greater understanding of kart dynamics will be possible.
1) Mechanical Weight Jacking - This type of weight transfer occurs when the steering wheel
is moved, causing the front wheels to turn. It can be seen and measured on scales.
2) Dynamic Weight Transfer - This type of weight transfer occurs in corners. It is caused by
lateral G-force shifting weight off of the left side (LS) tires and onto right side (RS) tires of
the kart.
3) Dynamic Weight Jacking - This type of weight transfer is really just a part of dynamic
weight transfer. When weight transfers from the LS to the RS of the kart in a corner, most of
the weight will tend to go toward either the right front (RF) tire or the right rear (RR) tire. It
is determined by chassis design and setup.
In some ways, mechanical weight jacking is the easiest mode of weight transfer to
understand. It occurs when the steering wheel is moved, turning the front wheels. With
steering input, the LF tire will move downward, while the RF tire will move upward. This is
easily seen and measured on scales. The amount and timing of the weight transfer is
affected by all of our front-end setup parameters; camber, caster, KPI, scrub radius, etc.
Despite how easy it is to see and measure, controlling this type of weight transfer is really
the "black magic" area of kart setup. The individual setup parameters that control how
mechanical weight jacking occurs are simple to understand. Understanding how they relate
to each other, and the ability to use them to your advantage, is something very few people
have mastered.
I'm not going to go any further into the details of this mode of weight transfer here. Look to
Mike McCarty's "Understanding Your Chassis" article in the 4-Cycle Chassis Tech Section
(http://www.4cycle.com/chassis/art.asp?art_id=34&art_content_id=210&FormArticle_Page
=1&) for a more complete description. For the purposes of this discussion, it is only
important to recognize that this type of weight transfer differs from the other types.
The concept of this type of weight transfer is very simple; when a kart is turning, weight
transfers from the LS of the kart to the RS. Dynamic weight transfer refers to the total
amount of weight that transfers from left to right. It can be easily predicted.
There are only a few items that affect dynamic weight transfer:
1) VCG - the height above the ground of the centre of gravity of the kart and driver.
2) Kart Track Width - the width of the kart. The distance between the outside edge of the
rear tire tread can be used.
In the "Understanding Your Chassis" article in the 4-Cycle Chassis Tech Section, mentions
the formula for calculating dynamic weight transfer:
"Weight Transfer: The amount of weight that transfers is proportional to the height of the
CG, and inversely proportional to the track width of the kart. The following formula will
always hold true: Total Transfer = Total Kart Weight * CG height * Cornering G's/ Track
Width."
Think about it this way; the length of the VCG is a lever. The total weight of the kart and
driver is distributed between the LS and RS of the kart. As G-force builds in a turn, it pushes
to the right on the VCG lever, attempting to lift the LS of the kart. As the LS of the kart lifts,
weight is taken off the LS tires, and moved to the RS tires. As more G-force pushes on the
VCG, more weight will be transferred.
It is important to understand that the amount of dynamic weight transfer does not depend
on tire pressure, chassis stiffness, or any other characteristic of kart design or setup. Also,
on a kart, this type of weight transfer happens almost instantaneously. There isn't much
that can be done to speed dynamic weight transfer up or slow it down, but it is easy to
control the total amount that occurs. Adjusting the VCG height or the track width of the kart
will change the total amount of weight transfer that occurs. Adjusting the amount of static
LS weight will determine how much total weight ends up on the RS of the kart in a turn,
which controls "side bite".
DYNAMIC WEIGHT JACKING
As mentioned previously, dynamic weight jacking is really just a part of dynamic weight
transfer. It is simply the distribution of the dynamically transferred weight between the RS
tires. Some percentage of the transferred weight will go to the RF tire, and the remaining
percentage will go to the RR tire. These percentages are determined by setup parameters
and, more importantly, chassis design.
The goal of chassis design and setup is to reach a neutral balance in handling during turn-in,
at the apex, and during the exit of a turn. The key to this balance is controlling the loading
on the RS tires throughout the turn. In controlling this balance, the unloading and re-loading
of the left rear (LR) tire is critical.
Statically, the LR tire on a kart carries the most weight. In a corner, most of the weight that
will transfer is going to come off of the LR tire. It will not transfer directly from left to right.
Much of the weight statically loaded on the LR tire will transfer to the RF tire.
From a chassis design perspective, the distribution of dynamic weight transfer is determined
by things like tubing diameter and wall thickness, and the stiffness or softness of the waist
of the kart. Another factor is the stiffness of the rear axle. Some chassis are equipped with
split tubes that can be clamped. This allows some adjustment of the dynamic weight jacking
characteristics of the chassis.
From a setup perspective the main thing that affects distribution of weight is the relative
stiffness of the RF and the RR of the kart. It helps to think of each corner of the kart
individually. Anything that changes the relative stiffness of the RF corner of the kart
compared to the RR corner will affect transferred weight distribution.
The key point to remember is that a stiffer corner will be more resistant to weight transfer.
Anything that softens a corner of the kart will cause more weight to transfer to it.
Let's go back for a minute to the first type of weight transfer discussed; mechanical weight
jacking. When the steering wheel is turned, it is obvious that weight is transferred from the
RF/LR tires onto the LF/RR tires. What is less obvious is that the RF is being made softer
compared to the RR. With the steering wheel turned, more of the transferred weight will be
distributed to the RF tire. More caster, scrub radius, etc. (anything that causes more
mechanical weight jacking), will cause more weight to transfer dynamically to the RF,
creating more grip on the RF tire and less on the RR tire.
Cross weight will also affect the distribution of transferred weight. With low-cross setups
(generally 54% or less) lowering cross weight will further soften the RF, increasing bite via
more weight transfer.
High-cross setups work differently. A high-cross setup creates a relatively stiffer RF
compared to the RR, and so less weight will transfer dynamically to the RF compared to a
low-cross setup. This type of setup works because of the grip provided by weight that is
statically pre-loaded onto the RF tire.
CONCLUSION
These are the basic issues surrounding weight transfer. Mike McCarty goes into a much
more detailed discussion of weight jacking axes, and chassis design variables in his manual
"Understanding Chassis Theory and Dynamics".
Next time the subject of weight transfer comes up, think about which type of weight
transfer is really being discussed. When you have questions about a setup issue, try to use
these terms to describe your thoughts.
Ignition Timing UNDERSTANDING IGNITION TIMING
Q: Why does a Non-Restricted engine seem to operate well with 28 degrees Ignition Timing
and a .052" jet at 6200 rpm, while a Restrictor Plate engine runs well with 30 degrees
Ignition Timing and a .062" jet at 5600 rpm?
Theory #1: You could assume as a rule that the higher the rpm band you operate in, the less
Ignition Timing you need to use.
Theory #2: You could assume as a rule that since the restricted engine is utilizing a larger jet
that you would need increased Ignition Timing in order to burn all of the fuel.
So we have:
Non-Restricted= Low Ignition/High Fuel
Restricted= High Ignition/Low Fuel
Is either theory true? No. The hole in both theories is that a Limited Modified engine will
operate properly in excess of 9200 rpm while using High Fuel and High Ignition Timing.
What about the Restricted engine using a larger jet? Even though the jet size is larger on a
restricted engine, it has to be larger because of the reduced fuel signal in the carb venture.
So, the restricted engine will rarely use more fuel than a Non-Restricted engine, even
though the jet size would make a person think so.
Does more fuel use require more Ignition Timing? No. The final clue to my puzzle came in
building an Open class engine. Larger than all of the aforementioned engines, this baby was
a Fuel Hog, yet it operated best at 28 degrees of Ignition Timing.
So, we have:
Open= Low Ignition/Very High Fuel
How can that be? The answer is found in VE (Volumetric Efficiency). Volumetric Efficiency is
simply how well an engine cylinder fills and evacuates (empties) within a given amount of
time.
In the case of our restricted engine, any engine when restricted by a plate forms turbulence
inside the port, which in turn impedes flow. The end result is reduced VE. Turbulence
creates a poorly mixed fuel/air charge which resists efficient combustion in the cylinder,
thus Increased Ignition Timing is required in order for the engine to produce peak
combustion pressure at the most opportune time, transferring the resultant forces to the
piston, connecting rod, and eventually the crankshaft.
What about the Limited engine? The Limited worked well with Increased Ignition Timing
because there was a lot more fuel to burn, but the Open worked well at 28 degrees with
even more fuel. Why? Because of flow. The Open had optimized larger ports, Big valves, and
a harder "pull" to fill the cylinder because of increased cubic inches (bore and/or stroke are
larger). In short, because the Open filled the cylinder more efficiently (VE) than any of the
other engine designs.
In Summary:
The proper use of Ignition Timing is a balancing act dependent upon VE.
Tires!!!!
Tires. Boy, what a can of worms this is! I could tell you how to mount them, and spend this
evening watching the Winston Cup race I taped, but then I wouldn't get all those lively
discussions these articles generate when I'm informed that my info is "slightly" inaccurate!
Enough whining, let us look at those numbers and compound codes printed on the side.
Racing kart tires are very low and very wide as compared to other race tires. The aspect
ratio or relationship of sidereal height t tread width is between 6% and 37%. Formula 1 tires
are 45%. This allows karts to have a low ride height and large contact patch. This ratio is
shown in a street tire as the "50" number in a 235/50R15 type of high performance tire. The
other numbers that describe the tire, for example an 11x6.00-5 tire are the dimensional
sizes in inches. "11" means it stands 11 inches tall (and is 11 inches in diameter). The "6.00"
means the tread width or contact area is 6 inches wide (give or take
a little). The "5" is the wheel diameter if 5 inches.
The tire parts include the tread or section that contacts the road. A thin layer of rubber is
bonded to the tire here. It is the compound or formulation of this rubber that determines its
grip and wear characteristics. A soft compound such as Dunlop¹s R6 is best suited to colder
weather or low grip tracks.
The carcass is the main part of the tire. It is a bias or diagonal overlap of nylon cord layers.
This angle, cord size and sidewall stiffness determine the tire¹s response and ride nature.
The bead area is a bundle of steel wires that strengthen the carcass where it meets the
wheel. This forms the air seal and sometimes makes mounting and removing the tires so
difficult.
The tires should be mounted on a wheel that is approximately the same width as the tire.
(For example, mount a 4.5 tire on a 4 1/2" or 5" rim width.) This should provide a good
contact patch which uses the full tread to good advantage.
Here comes the tough part. Inflation pressure! Pressure and slip control the heat build-up in
a race tire. Finding the correct combination sometimes seems to fall between "dumb luck"
and "black art". Tire temperature determines the grip and rolling resistance a tire has.
"Proper" inflation pressure is a difficult thing to achieve because its meaning can vary with
driver, chassis, track layout, road surface, weather and temperature. Most manufacturers
have an approved range of 10 psi to 25 psi. However, a starting point of 16-18 front and
slightly more (2-3psi more) rear will give you a baseline from which to adjust. Because the
tire pressure is important to performance, an accurate dial type gauge is essential.
Atmospheric Temperature Change: The general rule is to raise pressure during the cool part
of the day. This will decrease the contact patch and generate more heat sooner. In a 4-cycle
kart we are unlikely to badly overheat a tire unless the driver is very erratic or the chassis
has a handling or weight distribution problem.
As the day warms up (noon), we can decrease the pressure 1.5 - 3.0 psi to decrease heat
build-up. Remember, heat is generated by the tire sliding. You know how hot sandpaper
gets as you work it harder and harder!
Compounds: Soft compounds are best suited to Spring/Fall racing or tracks where the
surface is very old or slippery. Harder compounds work better in warm, summer weather.
"SL" or club compounds work best with slightly higher pressures.
Watch for the tire to shred or get tiny little cuts or splits in the surface. This tire is
overheated. It should have a "pebbled" look to it. If the tire overheats even once, it will
suffer a significant amount of deterioration in grip next time you run it. This happens
because tires "cure" or get harder as heat cycles are applied to them.
Variation in Road Surface: If you attend a big race event, especially with a lot of 2-strokes,
rubber will build up on the track and some experimentation will be required. Usually you
will lover the tire pressure unless a bounce or hop begins in the chassis.
Rim Width Changes: A change in width on the same tire will change both lateral and vertical
stiffness. Do not make large changes here, but if the chassis doesn't slide smoothly, or if it
hops, or if it doesn't turn in comfortably, then widening the rim will make the transitions
more predictable. Overall grip will remain the same with equal pressure, however.
Tire Size: Larger front tires can cure a push or you could go to a narrower front rim width
with the same tire size. A larger tire (front or rear) will tend not to "bog" the chassis down
on a very sticky track. Narrower tires are usually used on Jr. karts or slippery tracks. Don't
forget that as you change the size at the rear, you also affect gear ratio. If you increase
circumference, each 1/2" requires a change of one tooth on the rear gear.
Breaking In Tires: A good rule for tire break-ins is to run 5 to 8 laps (but not a full speed) and
then let them cool completely or delay use for 1 day. The tread should appear rough or
"pebbled".
Remember, the tire needs heat to work effectively, but there are limits to how much. The
chassis should try to use all 4 tires as much as possible. That will show the best times "on
the watch". Use tire pressures when the chassis can't be adjusted any further or if tiny
changes need to be made. Don't be afraid to try changes, but get feedback from the driver,
form lap times, and from watching races on TV that tires are the most important factor in
performance. Use them effectively and have a great race!