ICPractical Ion Chromatography

Practical Ion
Chromatography
An Introduction
Practical Ion Chromatography
An Introduction
Dipl.-Ing. Claudia Eith

Prof. Dr. Maximilian Kolb
Prof. Dr. Andreas Seubert
Dr. Kai Henning Viehweger (Editor)
All rights reserved to the publisher, including translation.

Printed by Metrohm Ltd., CH-9101 Herisau, Switzerland
8.792.5003 – 2001-02
Practical Ion Chromatography 1

2 Metrohm Monograph
Contents
1 The authors .................................................................................................................................. 5
2 Introduction .................................................................................................................................. 6
3 Theoretical section ........................................................................................................................ 7
3.1 The history and importance of ion chromatography ............................................................... 7
3.2 Theory of chromatography .................................................................................................... 8
3.2.1 Chromatography divisions and terminology ................................................................ 8
3.2.2 Theoretical concepts for describing the chromatography process ............................. 12
3.3 Basic principles of ion chromatography (IC) ........................................................................ 17
3.3.1 Terminology and classification in LC ......................................................................... 17
3.3.2 Ion exchange ........................................................................................................... 17
3.3.3 Ion pair formation .................................................................................................... 19
3.3.4 Ion exclusion ........................................................................................................... 19
3.4 Retention models in ion chromatography ............................................................................. 21
3.4.1 Retention models in anion chromatography .............................................................. 21
3.4.2 Retention models in cation chromatography ............................................................. 27
3.5 Ion chromatography detection systems ............................................................................... 30
3.5.1 Electrochemical detection methods .......................................................................... 30

3.5.2 Spectroscopic detection methods ............................................................................. 35
3.6 Stationary phases in ion chromatography ............................................................................ 36
3.6.1 Overview of common stationary phases ................................................................... 36
3.6.2 Stationary phases in anion chromatography ............................................................. 38
3.6.3 Stationary phases in cation chromatography ............................................................ 38
3.6.4 Cation exchangers based on silica gel ...................................................................... 39
3.6.5 Cation exchangers based on organic polymers ......................................................... 39
3.6.6 Pellicular cation exchangers ..................................................................................... 39
3.6.7 Stationary phases in ion exclusion chromatography .................................................. 40
3.6.8 The meaning of the capacity of ion exchangers ......................................................... 40
3.7 Eluents in ion chromatography ............................................................................................ 41
3.7.1 Anion chromatography ............................................................................................. 41
3.7.2 Cation chromatography ............................................................................................ 44
3.7.2.1 Cation chromatography of alkali, alkaline earth and ammonium ions
with conductivity detection ......................................................................... 44
3.7.2.2 Cation chromatography of transition metal and alkaline earth ions
with post-column derivatization and photometric detection .......................... 45
3.7.2.3 Ion exclusion chromatography .................................................................... 47

4 Practical section ......................................................................................................................... 48
4.1 Information about the practical work .................................................................................... 48
4.2 Experiments covering the theory of ion chromatography ...................................................... 51
4.2.1 Experiment 1 - Ion chromatography with and without chemical suppression ........... 51
4.2.2 Experiment 2 - Capacity of separating columns ...................................................... 55
4.2.3 Experiment 3 - Selectivity of separating columns .................................................... 58
4.2.4 Experiment 4 - Calibration, detection and determination limits in ion
chromatography ............................................................................. 63
4.2.5 Experiment 5 - Altering the selectivity with the aid of crown ethers (18 Crown-6) .... 67
4.2.6 Experiment 6 - Altering the selectivity by using complexing agents .......................... 70
4.2.7 Experiment 7 - Preconcentration technique ............................................................. 76
4.3 Experiments for determining anions ..................................................................................... 80
4.3.1 Experiment 8 - Determining anions in drinking water ............................................... 80

4.3.2 Experiment 9 - Anions in ethanol and spirits (liquor) ............................................... 84
4.3.3 Experiment 10 - Anions in lettuce ............................................................................. 91
4.3.4 Experiment 11 - Phosphoric acid in cola drinks ........................................................ 95
4.3.5 Experiment 12 - Organic acids in wine ................................................................... 101
4.3.6 Experiment 13 - Determination of contaminants in borate – chloride and sulfate
in borax solutions ......................................................................... 107
4.3.7 Experiment 14 - Determination of anions in wastewater .......................................... 112
4.3.8 Experiment 15 - Fluoride in toothpaste .................................................................... 118
4.3.9 Experiment 16 - Anions in brown and white sugar .................................................. 122
4.3.10 Experiment 17 - Contaminants in hydrogen peroxide ............................................... 128
4.4 Experiments for determining cations .................................................................................. 135
4.4.1 Experiment 18 - Alkali metals and alkaline earth metals in drinking water and
mineral water ............................................................................... 135
4.4.2 Experiment 19 - Determination of transition metals ................................................. 139
4.4.3 Experiment 20 - Contaminants in silica gel – determination of calcium and
magnesium ions ........................................................................... 146
4.4.4 Experiment 21 - Cosmetics and corrosion protection: determination of
ethanolamine and alkali metals ...................................................... 150
4.4.5 Experiment 22 - Alkali metals and alkaline earth metals in wine .............................. 155
5 Literature cited .......................................................................................................................... 159
4 Metrohm Monograph
The authors
Claudia Eith
Studied chemistry at the Fachhochschule in Aalen, one term's practical work in the drinking water and
wastewater analysis sector in Adelaide (Australia); since 2000 with Metrohm AG in the R&D division.
Maximilian Kolb
Studied chemistry at the Technical University in Munich, promotion in the field of
homogeneous catalysis, then managed the water quality division of the water authority in
Traunstein for 5 years. Since 1982 Professor at the Fachhochschule Aalen; fields of
work: environmental technology, environmental analysis and chemometrics.
Andreas Seubert
Studied chemistry at Hannover University, promotion 1990: "Ultratrace analysis in highly
pure refractory metals with trace-matrix separation by ion chromatography". Habilitation
1995: "On-line HPLC-atomic spectrometry coupling applications in elemental analysis",
1998 to 2000 temporary professorship in ana-lytical chemistry at Kassel University, since
March 2000 professorship in analytical chemistry at the Philipps University in Marburg.
Kai Henning Viehweger

Studied chemistry at Hamburg University, thesis in the field of inorganic analysis. Promotion in
the field of research into marine and estuarine ecological systems; since 1996 in the
marketing division with Metrohm AG – international sales manager for ion chromatography.

Introduction
Examining things which do not reveal themselves directly is always a challenge. The reasons for this
vary from simple curiosity to the real necessity of survival. There are many different ways of looking
behind the curtains. The simplest way is to use the human senses: listening, touching, smelling,
tasting and seeing. In earlier days the alchemists liked to use these five senses. This is why today
acids taste acidic and bromine has its name derived from "bromos", Greek for fetid. To the naked
eye chromium appears to be colored, as "chroma" from a historical linguistic point of view is the
same as color. The alchemists also expressed their feelings with insults such as "you kobold" for
cobalt, the presence of which caused our ancestors great difficulty in the production of iron.
Many individual things cannot be seen directly. They are too thoroughly mixed or the
human senses are not capable of identifying them. This is the moment when analysis
comes into play. It is able to extract precise information from an undefined mixture of
components which cannot be obtained by the human senses alone.
Although the organism is full of them, the human senses cannot experience them directly. We
are talking about ions, those charged atoms or molecules which are an integral part of virtually
all living and dead matter. Ions are responsible for the transfer of information along the nerves,
for ensuring that digestion takes place, for making sure that the blood pressure is correct and
that there is sufficient oxygen in the blood. Ions bring salt into the sea, control your thirst and
ionic constituents are used as food by all living things – from bacteria up to human beings.
A knowledge about the type and number of ions to be found in the environment helps us to
understand biochemical and ecological relationships. If the ionic concentrations in a foodstuff
is known then these provide us with information about whether the food is safe to eat or not.
There are many different ways of determining ions qualitatively (by their type) and
quantitatively (by their amount). Each piece of information is important. One method used for
obtaining this information is ion chromatography. Chromatography basically means "writing
with color". In traditional analysis this means the separation of substances according to their
color and their determination by visual observation. Al-though not all ions are characterized by
visible colors the term has been retained, but other methods of determination are used today.
Ion chromatography is one member of this large family of chromatographic methods. It can be used – to
put it very simply – to determine all ions which carry one or two charges. In the past ion chromatography or
"IC" used to be a very expensive method but today it is much more favorably priced. This is why it has
developed into a universal and powerful analytical tool which is easy to use.
This "Practical Ion Chromatography" will show that IC is not just an abstract analytical form,
but that it can provide rapid answers to common daily problems such as: Is the drinking water
suitable for feeding babies? How much nitrate is there in the spinach? Why does the washing
machine scale up? Does the wastewater cause environmental pollution? As accurate practical
analytical work is almost impossible without a theoretical background this monograph also
contains detailed information in a separate theoreti-cal section.
"Practical Ion Chromatography" is intended not only to provide you with a knowledge of
the basic prin-ciples of IC but also to provide you with an overview of general
chromatographic principles. And chroma-tography can do an awful lot: it satisfies
scientific curiosity and ensures healthy survival in a polluted environment.
6 Metrohm Monograph
3 Theoretical section
3.1 The history and importance of ion chromatography
The beginnings of ion chromatography (IC) or, more exactly, ion exchange chromatography go back to the
middle of the previous century. Between 1935 and 1950 knowledge about ion exchangers and their appli-
cations was considerably extended by the "Manhattan project". In the fifties and sixties theoretical models
for understanding the phenomenon of ion exchange and of ion chromatography, which is based on this,
were worked out. Continuous detectors were used in the seventies; this allowed the jump from low-
pressure to high-performance chromatography to be completed.
Table 1 History of ion exchange and ion chromatography, the analytical technique based on ion exchange
ca. 1850 Soil as an ion exchanger for Mg2+, Ca2+ and NH4+ Thomson & Way LC
1935 Sulfonated and aminated condensation polymers Adams, Holmes
(phenol/formaldehyde)
1942 Sulfonated PS/DVB resin as cation exchanger d'Alelio
(Manhattan Project)
1947 Aminated PS/DVB resin as anion exchanger McBurney
1953 Ion exclusion chromatography Wheaton, Baumann
1957 Macroporous ion exchangers Corte, Meyer, Kunin et al.
1959 Basic theoretical principles Helfferich
1967-70 Pellicular ion exchangers Horvath, Kirkland
1975 Ion exchange chromatography with conductivity Small, Stevens, Baumann
detection using a "stripper" HPLC
1979 Conductivity detection without a "stripper" Gjerde, Fritz, Schmuckler
1976-80 Ion pair chromatography Waters, Bidlingmeier,
Horvath et al.
The term 'ion chromatography' was coined in 1975 with the introduction of detection by conductivity
combined with a chemical reduction in conductivity by Small, Stevens and Baumann; it was subsequently
used as a trade name for marketing purposes for a long time. In the meantime the abbreviated term 'ion
chromatography' has become established as the superordinate term for the ion exchange, ion exclusion
and ion pair chromatography methods included under high performance liquid chromatography (HPLC)
[1]. IC today is dominant in the determination of anions while the atomic spectrometry
methods, com-monly used for the determination of cations, are hardly useful for determining
the electronegative anion formers of the fifth to seventh main groups of the periodic system.
The most important field of application today for anion chromatography is the routine investigation of
aqueous systems; this is of vital importance in the analysis of drinking water [2,3,4]. IC is also used for the
analysis of the element species in anionic elements or complexes; this is mainly for solving environmen-

tally relevant problems. The third largest field of application for anion chromatography is ultratrace
analysis in ultrapure process chemicals required chiefly in the semiconductor industry.
Today the ion exchangers normally used for HPLC consist of spherical polymer particles with
a diameter of about 5 to 15 µm. Various methods are used to attach so-called anchor groups
to the surface of the polymer; these are used as spacers between the basic polymer and real
functional groups. These normally consist of quaternary ammonium ions which are chemically
attached to the anchor groups. The total number of functional groups is known as the
exchanger capacity; this is a basic characteristic of ion exchangers.
Commercial packing materials for anion chromatography are of a low-capacity nature with exchanger
capacities of between 50 and 100 µmol per separating column. This results from the dominant application
of conductivity detection which is universally used for ions because the sensitive detection of the analytes
requires that the elution system used has as low a self-conductivity as possible. With low-capacity anion
exchangers very dilute aqueous solutions of NaOH or carbonate buffers are usually quite adequate; their
self-conductivity can be additionally reduced by chemical suppression [2,4].
In anion chromatography it is chiefly functional groups of Type I (trimethylammonium, TMA) and
Type II (dimethylethanolammonium, DMEA) which are used today. As the real interaction between
the stationary phase and the analyte anions takes place at the functional group this means that its
structure has a decisive influence on the selective behavior of packing materials. According to
current knowledge the polarity of the functional groups, which can be controlled by the number of
hydroxyethyl residues (-CH2CH2OH) on the quaternary nitrogen, is of particular importance [2,4].
The term "ion chromatography" includes all separations of ionic species within HPLC with online detection
and is therefore largely independent of apparative limitations [5]. IC has developed into the method of
choice, above all in anion analysis, because of the wide range of separating columns, elution systems and
detectors which are now available. The reason for this is that only a few separation processes exist for
anions; these are hardly suitable for practical use. Gravimetric and volumetric methods are limited by their
sensitivity and their selectivity. Even the meteoric development of gas chromatography from 1965 on-
wards did not have any great advantages for anions, as the non-volatile ions needed to be derivatized first
and the sensitivity did not meet the demands placed on trace analysis today [6]. For the analysis of cations
powerful atomic spectrometry alternatives to IC exist, e.g. ICP-AES/MS, so that the value of cation chro-
matography is considerably less when compared with anion chromatography. However, cation chroma-
tography has achieved a certain importance in the analysis of alkali metals and alkaline earths and in the
determination of ammonium-nitrogen (drinking water analysis). In the speciation of ionic compounds IC in
combination with element-specific detectors is indispensable. A good overview of the applications of IC in
various sectors is given in the works of Haddad et al. and Weiss [2,4].
3.2 Theory of chromatography

3.2.1 Chromatography divisions and terminology
Chromatography is a physicochemical method for separating mixtures of substances. The
separation effect is based on repeated distribution between two phases; one phase is stationary
while the second, mobile phase moves in a particular direction [7,8]. Chromatography techniques
are divided up according to the physical states of the two participating phases:
8 Metrohm
Monograph
Figure 1 Division of chromatography
methods according to the
states of the stationary and
mobile phases
A further differentiation of chromatography methods can be made according to the basic

processes which occur during separation, such as adsorption or distribution, or
according to the type of procedure carried out (column or planar chromatography) [9].
Retention parameters
If a mixture of substances is subjected to chromatographic separation then a distribution equilibrium
is formed between the mobile and stationary phases for each individual component. The
substances can only be separated successfully when the distribution coefficients D of the
components differ sufficiently from one another. D is defined as the ratio of the concentrations of a
substance A between the stationary (Index S) and the mobile phases (Index M):
(1)
Accordingly substances with a larger distribution coefficient D will be held back (retained) more strongly
than those with a smaller D. The chromatographic separation procedure is shown in the form of a chro-
matogram in which a detector signal is recorded as a function of the elution volume of the mobile phase or
the time. This means that it corresponds to a concentration or mass profile as a function of time. The
detector signal should be proportional to the concentration of an analyte at the end of the migration path
[8]. As shown in equation 2, the residence time or gross retention time tR of a substance on the stationary
phase is obtained by adding the net retention time tS, which corresponds to the actual residence time on the
migration path, and the flow time of the mobile phase without any interaction, the dead time tM.
(2)
Owing to the formation of channels, diffusion processes or irregularities in the equilibrium achieved be-
tween the mobile and stationary phases some particles may pass through the stationary phase more
slowly or more quickly than is to be expected from the net retention time t S. This means that a chromato-
gram does not consist of an infinite number of narrow signals, but ideally of Gaussian peaks (Figure 2).

Figure 2 Elution chromatogram of a separation by ion chromatography with indication of the
most important quantities
As a result of diffusion processes, which increase in importance as the residence time on

the stationary phase increases, the width of a substance peak increases as the retention
time increases. This phenom-enon is characteristic of all chromatography methods.
As already mentioned, under ideal circumstances a peak in a chromatogram shows Gaussian distribution.
Figure 3 shows an example of Gaussian distribution.
Figure 3 Gaussian distribution with

the most important quantities
10 Metrohm
Monograph
The width at half the peak height is known as the half width b 0,5 and corresponds to the 2.354-fold variance
σ of the distribution. The base width w is defined by the difference of the points of intersection
of the slope tangents with the y-axis which is the same as the 4-fold variance of the Gauss
function. Both quantities are a measure of the performance of a chromatography separating
column and, with an ideal peak shape, can be used for calculating the number of plates.
Variations from the ideal peak form can be described by a so-called asymmetry factor T. This
is defined as the ratio of the distances A and B between the central verticals and the slopes of
the distribution at 10% of their height (Figures 2 and 3) and can be calculated to:
(3)
For Gaussian peaks T = 1. A variation towards a larger T value is known as tailing, towards a smaller one
as fronting. In practice the intention is to achieve an asymmetry factor from T = 0.9 to 1.1.
Retention factor, selectivity and resolution

As the gross retention time t R depends largely on the chromatographic conditions it is only under defined
conditions that it is characteristic for a particular substance and can therefore be used for qualitative
identification. A dimensionless quantity is introduced, the retention factor k'; this allows comparisons to
be made between different chromatographic systems. It provides information about how much longer a
substance remains on the migration distance than in the mobile phase [8]. The retention factor is math-
ematically defined as the product of the distribution coefficient D and the phase volume ratio between the
mobile and stationary phases or as the ratio of the net retention time to the dead time. A calculation over
the length of the migration distance L and the speed of the mobile phase u is also possible (Equation 4).
(4)
At small values of k' a substance elutes close to the dead time or at the dead volume of the
chromatogra-phy system; this means that separation is poor. If k' is very large this means that,
although the separation is good, there is a long residence time on the migration path and the
peak becomes wider. Ideally the retention factor should be between 2 and 5.
Two substances will only be adequately separated if their retention factors differ from each
other suffi-ciently. The selectivity coefficient α, also known as the relative separating factor,
is a measure of the separability of two substances and is defined as follows:
(5)
If two substances cannot be separated then α = 1 and coelution occurs. The larger the value
of α, the better the separation. However, as α increases the time required for the separation
also increases, so that in practice selectivity coefficients of α = 1.5 are aimed for [10].
The selectivity coefficient does not describe the quality of the separation process. The resolution R does
not just take the relative positions of the peaks into account, but also their half-width (b 0.5) and base width
(w) values, as can be seen in Equation 6.

(6)
If the difference between the retention times of two peaks is large in relation to their base
widths or half-widths then the resolution is good. If an ideal peak symmetry is assumed then
two substances with R = 0.5 can still be identified. For qualitative separation R should be 1
(4σ-separation), for quantification a resolution of R = 1.2 to 1.5 is aimed for [25]. Resolutions
of R ≥ 2 (8σ-separation) are to be avoided because of the long analysis times involved.
3.2.2 Theoretical concepts for describing the chromatography

process The theoretical separation stages model
The theoretical separation stages model is derived from the distillation process and is used to
describe chromatographic separations [11]. It divides the stationary phase into single sections,
the theoretical separation stages or plates, on which in principle a completely reversible and
infinitely quick equilibrium between the mobile and stationary phases is achieved exactly and
instantaneously. The performance (efficiency) of a chromatography system is therefore
characterized by as high a number of theoretical separation stages as possible.
The number of theoretical plates N can be determined directly from the chromatogram by
using the variance as well as the base width and half-widths and is calculated as follows [12]:
(7)
Instead of the number of theoretical plates the height equivalent to a theoretical plate
HETP can also be used to describe the separating performance.
(8)
From Equations 5 ... 8 it can be seen that a stationary phase with a very large number of
theoretical plates can even separate substances from one another whose selectivity
coefficients or resolutions hardly differ at all. The equations also allow the calculation of
the number of theoretical plates which are necessary to solve a separation problem.
The theoretical separation stages model can be used to explain the occurrence of Gaussian signals
in chromatography if it is assumed that, because of flow and diffusion processes, only a finitely
quick and incomplete equilibrium is achieved between the mobile and stationary phases. This
results in a peak broadening process as a narrow substance zone at the start of the migration path
clearly becomes broader as the residence time on the stationary phase increases.
The calculation of the number of theoretical plates according to Equation 7 assumes that the
peak shape is ideal; however, this rarely occurs in reality. With asymmetric peak shapes the
calculation must be carried out according to the momental method [13]. Equation 9 includes
the symmetry factor and produces approximate values which make sense.
12 Metrohm
Monograph
(9)
A number of effective plates n, which represents the actual separation performance more closely
than the number of theoretical plates N, is corrected by the retention factor k' and is obtained from:
(10)
The dynamic theory (van Deemter theory)

The decisive weakness of the theoretical separation stages model is that distillation and chromatography
are based on two fundamentally different physicochemical processes. Also no assumptions are made
about the influence of important parameters which are experimentally accessible and which do not affect
the type or quality of the stationary phase itself [14,15]. These could be:
• flow rate of the mobile phase
• particle diameter in the stationary phase
• thickness of surface films on the packing material
In addition, quantities such as the diffusion coefficients in the mobile and stationary phases, the tempera-
ture or the detector volume in liquid chromatography are very important for the separation performance.
The dynamic theory developed by van Deemter is, in principle, an extension of the
theoretical separation stages model which takes non-ideal limiting conditions into
account [16]. The following assumptions are made:
• no spontaneous and unhindered achievement of equilibria
• delayed mass transport in the stationary and mobile phases
• no homogeneous mobile phase flow rate over the whole cross-section of the column
• occurrence of scatter diffusion and channel formation in the stationary phase
• longitudinal diffusion irrespective of the mobile phase speed and directly proportional
to the residence time on the migration path
The relationship between the dynamic effects mentioned above and the height
equivalent to a theoretical plate is given by the van Deemter equation.
(11)
The three terms A, B and C depend in different ways upon the flow rate u of the mobile phase. The terms
A and B describe the whole mass transport through the stationary phase; term C is determined by interfer-
ence to the achievement of the equilibrium between the mobile and stationary phases.
Term A describes the eddy diffusion, which can be regarded as being a cause of peak widening owing to a
multi-pathway effect. This term is also known as the packing factor and is independent of the linear flow
rate u of the mobile phase, at least in a first approximation. The following relationship applies to term A:
(12)

In Equation (12) dp is the average particle diameter in the stationary phase, λ describes the statistical
irregularity of the packing; this should be as homogeneous as possible and consist of uniform particles.
Term B describes the longitudinal diffusion in or against the direction of flow of the mobile
phase. It is of particular interest when capillary columns are used in gas chromatography
(GC), as the diffusion coeffi-cients in gases are higher by 4 to 5 powers of ten than in liquids.
B is calculated as being the product of the diffusion coefficient in the mobile phase D M and the
labyrinth factor γ, which describes the porosity of the stationary phase.
(13)
B = 2 · γ · DM
As the importance of diffusion decreases as the flow rate of the mobile phase increases
this means that B is inversely proportional to u.
Term C is known as the mass transfer term. The delayed mass transfer between the mobile and stationary
phases usually has the greatest influence on peak broadening. Interference in achieving equilibrium be-
tween the mobile and stationary phases increases as u increases, which is why there is a direct propor-
tionality to the linear flow rate. The delays in mass transfer result from the very small diffusion coefficient
DS in the stationary phase in comparison to the mobile phase; this is why particles which are actually
resident in the pores of the stationary phase remain behind the peak maximum as it moves on together
with the mobile phase. The term C can be considerably reduced by short diffusion paths and quick transfer
processes. This can mainly be achieved by localizing the pores on the surface so that only a few extend
into the interior of the stationary phase. The mass transfer term C is calculated as follows:
(14)
Graphical representation of the van Deemter equation shows a hyperbolic curve, from
whose minimum value the flow rate u for the minimum plate height (maximum number of
plates) can be determined (Figure 4).
Figure 4 Representation of the individual

terms of the van Deemter theory with
the resulting van Deemter curve
showing the optimum flow rate
Even the dynamic theory is based on ideal requirements. In reality the three terms A, B and C
are only independent of one another in a first approximation, with there being an additional
influence of the flow rate u on the eddy diffusion (Term A). Term C can be differentiated by
using the terms CM and CS, which describe the mass transfer in the mobile phase (C M) and to
the stationary phase and back (C S). This is why the original van Deemter equation has been
modified for numerous applications in HPLC, GC and TLC [17,18].
14 Metrohm
Monograph
Modern liquid chromatography (LC)
Liquid chromatography LC is to be regarded as the generic term for numerous modern liquid
chromatog-raphy separation methods. It can be used for a wide range of different substances and is
characterized by its excellent analytical performance. LC also includes ion chromatography (IC)
which is probably the most important separation method used in modern analytical chemistry [3].
HPLC is a logical further development of the classical liquid chromatography (LC). In classical LC,
intro-duced by Tswett in 1906, glass columns with a diameter of 1 to 5 cm and a length of up to 500
cm were used; these were filled with separation phases with particle sizes of 150 to 200 µm. Even
separations of simple mixtures of substances could often take several hours with an average
separation performance. As a result of the understanding of the chromatography process which was
later developed (Equation 11) it became clear that increased performance could only be achieved
by a dramatic reduction of the particle diameter in the stationary phase; however, this placed
completely new demands on the equipment used for chromatography.
Since about 1970 special and powerful instrument technology has become available which is able to
overcome the high counter-pressures of 10 to 50 MPa which occur when packing materials with a particle
diameter of 3 to 10 µm and separating columns of 125 to 250 mm length x 4 mm ID are used.
As a result of the dramatic miniaturization HPLC has developed into a purely analytical
separating method; in contrast classical LC is today practically only used for preparative
purposes. The advantages of HPLC in comparison to classical LC are chiefly:
• excellent chromatographic efficiency
• continuous working process
• online detection of the separated substances
• high sensitivity and reproducibility
• utilization of the retention time for qualitative identification of substances
• short analysis times
Irrespective of its field of application, an HPLC system consists chiefly of the components shown in Figure
5: the high-performance pump with mobile phase (eluent) storage, injector (sample introduction),
sepa-rating column and detection system (including derivatization, data acquisition and processing):
Figure 5 HPLC or IC unit setup with the most important components

Apart from the separating column the pump is the heart of every HPLC system. It must be able to
deliver the eluent as uniformly and pulsation-free as possible, even against high counter-pressures.
This means that it is also necessary to use a special sample loop injector for sample application. A
6-way valve is normally used; this is able to accept a defined volume of the sample in a loop at
standard pressure and to transfer this to the HPLC system operating at high pressure. The
composition of the mobile phase and the type of separating column must be adapted to the
analytical problem to be solved. This also applies to the selection of the detection system. Today all
data acquisition and processing is carried out by computer. This basic setup of an HPLC system can
be extended virtually at will to solve a particular analytical problem.
Separating principles in LC
HPLC can be differentiated according to the different physicochemical interactions
between the substances in a sample and the stationary phase. Although in reality there
are usually several different mechanisms responsible for a successful separation [9], a
rough classification according to the following separation mechanisms is possible:
• adsorption
• distribution
• size exclusion
• affinity
• ion exchange
• ion pair formation
• ion exclusion
Adsorption chromatography is defined by interfacial reactions, in which liquid or gaseous
substances are enriched at a solid phase. Various models are available for providing a qualitative
and quantitative descrip-tion of adsorption processes; here we only refer you to the relevant
physical chemistry literature [19]. Two different techniques are used. In normal phase
chromatography the stationary phase is usually silica gel and therefore considerably more polar
than the mobile phase (hydrocarbons). In reversed phase chroma-tography the conditions are
exactly the opposite. For practical reasons, which chiefly concern eluent handling, virtually only RPC
is used today [3,9].
In distribution chromatography the stationary phase is a liquid which is immiscible with the mobile
phase. Separation is based on the differing solubilities of the analytes in the two phases. In an ideal
case the Nernst distribution law applies. This separating mechanism plays an important role,
particularly in gas chromatography when capillaries coated with separating liquids are used as the
stationary phase. Distri-bution chromatography may also occur in HPLC if silica gels modified with
non-polar hydrocarbons, e.g. so-called octadecyl phases, are used as the separating material.
Size exclusion chromatography (SEC) allows separation according to the molecular size as a result of
sieve effects. Silica gels or organic polymer resins with a defined pore structure are used as the stationary
phase. Smaller analytes can diffuse into the pores and are retarded. As the molecule size increases any
interaction with the pores becomes less likely, until at a particular size molecules are completely excluded
and practically elute in the dead volume. SEC is widely used in polymer analysis and bioanalysis.
Affinity chromatography allows the separation of mixtures of substances by selective or specific interac-
tive forces. Highly specific interactions can be observed between antibodies and antigens (key-keyhole
principle), as well as with enzymes and their substrates in particular. In practice enzymes or antibodies are
chemically immobilized on a stationary phase. If there is a corresponding substrate or antigen in the
16 Metrohm
Monograph
sample then this is retarded with extreme selectivity. This is why bioaffinity chromatography is
indispens-able in the active substance analysis sector (pharmacology).
Ion exchange chromatography (IC) together with ion pair and ion exclusion
chromatography are de-scribed in detail in the following section.
3.3 Basic principles of ion chromatography (IC)

3.3.1 Terminology and classification in LC
Ion exchange chromatography or ion chromatography (IC) is a subdivision of HPLC.
According to IUPAC ion exchange chromatography is defined as follows [7,8]:
"In ion exchange chromatography separation is based on differences in the ion exchange
affinities of the individual analytes. If inorganic ions are separated and can be detected by
conductivity detectors or by indirect UV detection then this is also called ion chromatography".
For several reasons this definition is an unhappy choice. The detection technique should be
considered separately from the existing separation mechanism. Apart from this, a limitation of
the term 'ion chroma-tography' to inorganic ions is difficult to understand as in practice in any
given system both organic and inorganic ions can be separated and identified simultaneously.
An older, more general definition is more suitable for defining ion chromatography [20]:
"Ion chromatography includes all rapid liquid chromatography separations of ions in
columns coupled online with detection and quantification in a flow-through detector."
This definition characterizes ion chromatography irrespective of the separating
mechanism and detection method while at the same time distinguishing it from classical
ion exchange. The following separation principles apply in ion chromatography:
• ion exchange
• ion pair formation
• ion exclusion
Chromatography methods are defined by the chief separation mechanism used. Today ion exchange chro-
matography is simply known as ion chromatography (IC), while ion pair chromatography (IPC) and ion
exclusion chromatography (IEC) are regarded as being more specialized applications.
3.3.2 Ion exchange

Ion exchange chromatography (IC) is based on a stoichiometric chemical reaction between ions in
a solution and a normally solid substance carrying functional groups which can fix ions as a result of
electrostatic forces. In the simplest case in cation chromatography these are sulfonic acid groups, in
anion chromatography quaternary ammonium groups. In theory ions with the same charge can be
exchanged completely reversibly between the two phases. The process of ion exchange leads to a
condition of equilibrium. The side towards which the equilibrium lies depends on the affinity of the
participating ions to the functional groups of the stationary phase. Figure 6 is a schematic diagram
showing the exchange processes for cations and anions. The analyte ions are marked A, the eluent
ions competing with them for the exchange positions with E.

Figure 6 Schematic diagram showing the ion exchange process in ion chromatography. Left: cation exchange,
right: anion exchange
Thermodynamic aspects of the ion exchange process

Ion exchangers normally consist of solid phases on whose surface ionic groups are
fixed. Because of the condition of electroneutrality there is always an oppositely-charged
counter-ion in the vicinity of the func-tional group. The counter-ion usually originates from
the mobile phase and is therefore also known as the eluent ion.
If a sample is added which contains two analyte ions A – and B– then these briefly displace the
eluent ions E– and are retained at the fixed charge before they are in turn exchanged for the
eluent ion. For anion chromatography this results in the following reversible equilibria:
(15)
(16)
The different affinities of A – and B– to the functional groups mean that separation is possible. The equilib-
rium constant K is also known as the selectivity coefficient and is calculated as follows for anion A-:
(17)
If it can be assumed that the concentration of the eluent ions is normally higher than that of the
analyte ions by several powers of ten then [E–] can be regarded as being a constant in the mobile
and stationary phases. This means that the distribution coefficient D A (Equation 1) and the retention
factor k'A (Equation 4) can be calculated. Strictly speaking, such calculations are only permissible if
the concentrations in Equa-tion 17 correspond to the activities; however, this is only the case for an
infinite dilution [19]. In principle the activities of the ions in the stationary phase are inaccessible [4].
For the most frequently used ion exchangers of low capacity, which can only be used as the mobile
phase with very dilute electrolytes, the activities are simply disregarded. Such very coarse
approximations are no longer valid for high-capacity (> 200 mmol/g) packing materials and
concentrated eluents; these show clear variations from the 'ideal' behavior.
18 Metrohm
Monograph
3.3.3 Ion pair formation
With the aid of ion pair chromatography it is possible to separate the same analytes as in ion
exclusion chromatography, but the separation mechanism is completely different. The stationary
phases used are completely polar reversed phase materials such as are used in distribution
chromatography. A so-called ion pair regent is added to the eluents; this consists of anionic or
cationic surfactants such as tetraalkylammonium salts or n-alkylsulfonic acids. Together with the
oppositely charged analyte ions the ion pair reagents form an uncharged ion pair, which can be
retarded at the stationary phase by hydropho-bic interactions. Separation is possible because of the
formation constants of the ion pairs and their different degrees of adsorption. Figure 7 shows a
simplified static ion exchange model in which it is assumed that interactions with the analytes only
occur after adsorption of the ion pair reagent at the stationary phase.
Figure 7 Schematic diagram showing the static ion exchange model in ion pair
chromatography (IPC). The separation principle applies to both anions and cations.
3.3.4 Ion exclusion

Ion exclusion chromatography (IEC) is mainly used for the separation of weak acids or
bases [2,4]. The greatest importance of IEC is for the analysis of weak acids such as
carboxylic acids, carbohydrates, phenols or amino acids. Figure 8 shows the separation
principle of IEC using an R - COOH carboxylic acid as an example.

Figure 8 Donnan exclusion as the separation principle in ion exclusion chromatography (IEC)
In IEC a completely sulfonated cation exchanger whose sulfonic acids groups are electrically neutral with protons
as counter ions is frequently used as packing material. In aqueous eluents the functional groups are hydrated. The
hydrate shell is limited by an (imaginary) negatively charged membrane (Donnan mem-brane). It is only passable
by uncharged, non-dissociated molecules such as water. Organic carboxylic acids can be separated if strong
mineral acids such as sulfuric acid are used as the mobile phase. Owing to the low acid constants (pK A values) of
the carboxylic acids these are present in a virtually fully non-dissociated form in strongly acidic eluents. They can
pass through the Donnan membrane and be adsorbed at the stationary phase, whereas the sulfate ions of the
completely dissociated sulfuric acid are excluded.
Figure 9 shows the typical dependency of the elution volume of an acid on its pKA value
for separation by ion exclusion. Superimposed adsorption (long-chain carboxylic acids,
H2S) and the limits of the practical working range can be clearly recognized. In the final
instance carboxylic acids are separated because of their different pKA values.
Figure 9 Dependency of the elution volume on

the particular pKA value of the acids
in ion exclusion chromatography
20 Metrohm
Monograph
3.4 Retention models in ion chromatography
In an ideal case the retention of an analyte in ion chromatography would only be determined by its affinity
to the functional groups of the ion exchanger. This affinity can be described by the formulation of a chemi-
cal reaction, the ion exchange reaction, and can be explained by using the law of mass action.
The retention models described below attempt to make predictions about the retention behavior of partici-
pating analytes under particular chromatographic conditions based on the law of mass action. If the
resulting models are suitable for explaining the macroscopic observations then with their help it is pos-
sible, for example, to optimize an elution system for a particular separation problem.
3.4.1 Retention models in anion chromatography

The following observations initially only involve elution by isoionic displacement as the simplest
elution mechanism in ion chromatography. The actual example refers to anion chromatography, but
the same considerations apply similarly to cation chromatography. Only when complexing agents
are added to the eluents is it necessary to extend the retention model: this is described in the
section: «Retention model for elution in the presence of complexing agents» (section 3.4.2).
Retention model for eluents with one anion

If electroneutrality is assumed then the simplest approach to a retention model for
isoionic displacement is one in which a single eluent ion Ey– competes with one analyte
anion Ax– for the functional groups of the stationary phase [4]. The concentration of the
eluent anions Ey– remains constant with time (isocratic elution).
The exchange sites on a separating column with a capacity Q are occupied by eluent anions E y– at the
start of the chromatographic process. If a sample containing the analyte ion A x– is added then the following
equilibrium becomes established between the stationary phase (index S) and the mobile phase (index M):
(18)
According to the law of mass action this equilibrium can be described by a

thermodynamic equilibrium constant. If the activities of the participating ions are taken
into account then the following thermodynamic equilibrium constant is obtained:
(19)
As the activities of the participating ions cannot be determined in the stationary and
mobile phases the activity in the stationary phase is ignored and set as being 1.
If for the analyte anion Ax– two known quantities, the distribution coefficient DA and the
retention factor k'A, are now introduced from section 3.2.1,
(20)

then, by including these quantities and neglecting the activities, Equation 19 can be converted to:
(21)
As the concentration of the eluent ions E is normally higher than that of the analyte
anions Ax– by several powers of ten, a good approximation can be obtained by assuming
that all the functional groups are occupied by Ey–. Under this assumption the non-
determinable concentration of Ey– in the stationary phase can be replaced by the more
easily accessible parameters of exchange capacity Q and charge of the eluent anion y:
(22)
This means that Equation 21 can be converted to:

(23)
The retention factor k'A of the analyte anion Ax– can easily be obtained from a
chromatogram. Equation 23 is therefore solved for this quantity.
(24)
This equation is of crucial importance for anion chromatography as it provides a

quantitative relationship between the retention factor k' A and several experimentally
accessible parameters such as the concentra-tion of the eluent and the exchange
capacity. In practice a logarithmic version of Equation 24 is used for reasons of clarity.
(25)
From Equation 25 it can be seen that:

• Increasing the eluent concentration [Ey–] accelerates elution
o larger retention factors result from larger equilibrium constants KA,E, higher
exchange capacities Q and a larger phase-volume ratio Φ.
• Multivalent analytes Anx– are retarded more strongly than monovalent Ax–,
o at least as long as the eluent concentration [Ey–] is relatively low. This is also known
as electro-selectivity.
• Multivalent eluents Eny– have a higher elution power than monovalent Ey–
o the elution of multivalent analytes Anx– is more strongly influenced by increased
concentrations of monovalent eluent ions Ey– than that of monovalent analytes Ax–.
22 Metrohm
Monograph
As a first approximation it can be assumed that the selectivity coefficients are
independent of Q at constant Φ; this results in the following proportionality:
(26)
From Equation 26 it can be seen that if the exchange capacity Q is increased then the
concentration of the eluent [E y–] must be increased proportionally in order to obtain constant
retention factors. This is the reason why low-capacity separation phases are normally used in
ion chromatography, as high electrolyte concentrations would make the most important
detection method used in ion chromatography, conductiv-ity detection, practically impossible.
In order to optimize separation problems the eluent concentration [E y–] is often varied. If all
the other parameters occurring in Equation 25 are kept constant then this can be simplified to:
(27)
A graphical plot of Equation 27 gives a straight line with a slope m = – x/y and an
intercept on the axis C which contains the quantities Q, Φ and K A,E. If a monoanionic
eluent is used then m is also known as the effective charge. Figure 10 shows the result
of Equation 27 for various combinations of differently charged eluent and analyte anions.
Figure 10 Graphical presentation of Equation 28

for various combinations of differently
charged eluent and analyte anions [4].
Equation 27 has been confirmed in numerous publications; however, under the

assumption that low-capacity separation materials and dilute eluents have been used.
If the exchange capacity Q is varied while the other parameters remain constant, then
Equation 25 can be simplified to:
(28)
The graphical representation of this equation is similar to Figure 10, but with a positive slope. Chromato-
graphic investigations into the variation of Q have to date only been carried out once for the separation of
divalent cations. This has shown that, in contrast to previous assumptions, the retention factor and the
selectivity coefficients cannot be regarded as being independent of the exchange capacity. For the optimi-

zation of separation problems it is clear that apart from the concentration of the eluent [E
y–] the exchange capacity Q is also an important quantity.
The above considerations only apply for one analyte anion. If two different anions A x– and Bz–
compete for the functional groups then the following applies for the selectivity coefficients K A,B:
(29)
By taking Equation 20 into account the selectivity α is first obtained
(30)
and then after converting the Equations 31 a and b,
(31a)
(31b)
which can be simplified to for analytes with the same charge (x = z):
(32) or (33)
For the selectivity between two similarly charged analyte anions this means:
• it is only a function of the selectivity coefficients KA,B and the charges z and x,
• at constant KA,B the selectivity depends neither on the concentration [E y–] nor on the
chemical consti-tution of the eluent anion (!)
If A and B have different charges then:
• a depends on the retention factor of one of the two analytes,
• the two retention factors k'A and k'B are not independent of one another (!)
In Equations 31 to 33 it is particularly interesting that the selectivities of two anions initially depend on
neither the chemical constitution nor on the charge of the eluent anion, providing that the phase-volume
ratio and the selectivity coefficient are constant. However, in practice an alteration in a can be achieved by
a variation of [E y–], as two analytes with the same charge can nevertheless have different chemical
properties, e.g. polarizability and hydration; this can result in different affinities to the stationary phase.
However, these interactions are not taken into account in the classical derivation.
24 Metrohm
Monograph
Retention models for eluents with several anions
The previous observations have referred to elution systems with only a single eluent
anion. In practice there are usually several eluting species present, for example in
carbonate/hydrogen carbonate buffers or in multi-base acids such as phosphoric acids,
whose dissociation and therefore distribution of species depends strongly on the pH.
Even in simple cases in which none of the participating eluent anions is involved in the acid-base
equilib-rium, the relationship between the retention factor k' and the eluent concentration [E –] cannot
be repre-sented in the form of a simple log-log relationship according to Equation 28. This would
only be possible if the concentration or the elution power of the other eluent anions could be
ignored; this would then correspond to the retention model for monoanionic eluents.
In the literature several models concerned with polyanionic eluents are described; these
are briefly dis-cussed below:
• dominant equilibrium model [21]
• effective charge model [22-24]
• multiple eluent species model [25, 26]
If an eluent based on phosphate with H2PO4–, HPO42– and PO43–, (otherwise H2P–, HP2– and
P3–) and the monovalent analyte ion A– is considered then the following equilibria are formed:
(34)
(35)
(36)
Here the quantities x1..3 correspond to the shares of the particular reaction in the retention, which is why:
(37)
Both the dominant equilibrium model and the effective charge model postulate a particular
charge for the eluent anion, even though several species are present; this means that the
retention model for monoanionic eluents obtained in Section 3.4.1 can be used.
The dominant equilibrium model assumes that the equilibrium in Equation 36 is wholly on the right-hand
side, as P3– is bound far more strongly to the stationary phase than H 2P– and HP2– as a result of its higher
charge. This means that P3– alone is decisive for the elution so that the charge of the eluent anion is –3.
However, in practice this model only achieves a good agreement with multivalent analytes [4].
In the effective charge model an effective charge is calculated, taking into account the pH value, from
the molar fractions of the possible species H 2P–, HP2– and P3– [22]. By using these together with the
existing concentrations of the eluent species a relationship analogous to Equation 27 can be obtained.
However, a requirement for such a type of calculation is that the selectivities of the eluent species do not
differ greatly

with respect to the analyte ions A–. The effective charge model is chiefly suitable for use
with monovalent analytes [4].
In reality the multiple eluent species model is most suitable for the description of eluents whose compo-
nents are chemically derived from one another. The following observations are based on the model of
Mongay et al. [27], which is a further development of the work of Jenke and Pagenkopf [25].
Equations 34 to 36 can be used to express the global equilibrium on the separating
column (Equation 38). By taking Equation 37 into account, the equilibrium constants K A,P
can be defined for the exchange process if the activities are ignored (Equation 39).
(38)
(39)
The further mathematical treatment is carried out as for the derivation of the retention
model for monoanionic eluents. The following must chiefly be taken into account:
• the (possible) dissociation of the analyte anion A–
• the total concentration of the eluent species: cP = [H3P] + [H2P–] + [HP2–] + [P3–]
• the extent of the interactions between the eluent species and the functional groups
The introduction of the retention factors k' A (Equation 20) and the capacity Q (Equation
22) supplies, after further mathematical conversion, a complicated expression for k'A [28];
this is given here only in its logarithmic and further simplified form:
(40)
C3 is a constant which, similar to Equation 27, contains quantities such as the phase-volume ratio,
the capacity and the equilibrium constant; c P is the total of the concentrations of the eluent species.
From Equation 40 it can be deduced that the slopes of the straight lines in a double logarithmic plot
must always be smaller than those according to the simple retention model for monoanionic eluents
(Equation 27), as the total in the brackets is always smaller than one. It is also clear that the pH
value has a decisive influence on the extent to which the log-log relationship is influenced.
For eluent species which are not chemically derived from one another Janoš et al. have provided a model
which was developed for describing eluents containing a phosphate buffer and additional perchlorate [29].
This model was derived according to similar considerations to those described above, but in addition an
exchange equilibrium must be taken into account for a further monovalent eluent ion. The calculations
provide very complicated expressions for the retention factor; these can be dramatically simplified for
neutral or acidic eluents. If only a single further monovalent eluent species is present in addition to the
perchlorate then Equation 41 is obtained in which x and y represent the contributions of the corresponding
equilibrium reactions (x: phosphate buffer, y: perchlorate) to the retention. As in the other models, C is a
26 Metrohm
Monograph
constant, while the factor a, which is not defined any more closely, is intended to take
into account how much more strongly the perchlorate ion is bound at the stationary
phase than the phosphate species involved.
(41)
As in Equation 41 the terms within the brackets are always smaller than one, the slope
of the log-log plot is always less than would be expected from the simple retention
model. In actual applications the model provides good agreement with the experimental
data. However, the form described above cannot be used for alkaline elution systems.
3.4.2 Retention models in cation chromatography

Cation chromatography must be divided into two groups of retention models. One group is
concerned with alkali metal and alkaline earth cations as analytes and only requires one elution
system based on isoionic displacement. In this case the stationary phase has carboxylic acid
groups as functional groups. In the separation of metal ions with two or more charges the use of a
complexing agent is essential; its influence on retention is described below.
Retention model for eluents with one cation

The explanations given in the Section «Retention model for eluents with one anion» apply in an analogous
way for cation chromatography with elution by isoionic displacement. In practice this is relevant for the
determination of alkali metals and alkaline earths, ammonium and short-chain amines. Apart from H +,
organic cations such as 2,3-diaminopropionic acid (DAP) are used as eluent cations in combination with
dilute hydrochloric acid. Depending on the set pH of the eluent, DAP is present in the ionic forms (1) and
(2) (Figure 11). After suppression the zwitterionic form (3) is obtained, which has no self-conductivity.
Figure 11 Ionic species of

diaminopropioni
c acid
Retention model for elution in the presence of complexing agents

In cation chromatography eluents which contain a complexing agent in addition to the eluent cation E n+ are
used for the separation of alkaline earth, transition and heavy metal ions. The complexing agents used are
mainly dicarboxylic acids H2L such as tartaric acid, oxalic acid, citric acid and also pyridinedicarboxylic
acid. The analytes form complexes of differing stabilities with the anions of the complexing agents HL – and
L2–; their stoichiometries also differ. As a result of the complexing process the effective charge, i.e. the
charge of the analyte present over an average period of time, is reduced. As this occurs in accordance
with the kinetics of complex formation and the stability constants of the complexes, the differences in
selectivity increase and the separation of even similar analytes becomes possible. Apart from ion
exchange, complex formation is decisive for the separation of higher-charged metal ions.

(42)
(43)
(44)
In order to take the influence of the complexing agent on the ion chromatography separation into
account the retention model for isoionic displacement (see Section 3.4) is extended. The α M value is
introduced as an influencing quantity which describes the degree of complex formation of the
analyte. The fraction αM of the free analyte ions in the mobile phase is given as
(45)
with [Me'] as the total concentration of the metal ions. The α M value can be calculated from the complex
formation constants, the acid dissociation constant of the carboxylic acid and the pH of the eluent. If
complex formation is taken into account then the following is obtained for the distribution coefficient D Me:
(46)
If it is assumed that only free analyte ions Mex+ interact with the carboxylic acid or sulfonic acid
groups and that c(Ez+) >> c(H+), then the following is obtained for Equation 21:
(47)
In a similar manner to Equation 25 the logarithmic form of Equation 47 is obtained as:
(48)
If several cationic metal species occur together, e.g. Me x+ and MeHL(x–1)+, then normally only a single
peak is obtained in the chromatogram for the analytes involved. The number of peaks which are
obtained depends on the kinetics of the complexing and decomplexing equilibria in the mobile
phase. Only one peak is obtained if the complex equilibria are achieved more rapidly in the mobile
phase in comparison to the residence time of the complex in the stationary phase. On the other
hand, if the complexing process occurs slowly then asymmetric or multiple peaks may occur.
28 Metrohm
Monograph
If it is assumed that all metal species present in the mobile phase can interact with the stationary phase
then the following is obtained for the experimentally determined capacity factor k' exp of the analyte:
(49)
Consideration of the dependency of the capacity factor on the influencing quantities Q, [E y+]
as well as αM requires that the relationship presented in Equation 48 is used as the basis, as
the divalent analytes mainly form neutral or anionic complexes with strong complexing agents.
Calculation of αM values
According to Equation 45, the αM value is defined as the ratio of the concentration of the
free metal ions to the total concentration of the metal ions. The concentrations of the
metal species present in the mobile phase can be calculated from the relevant complex
formation constants and the acid dissociation con-stants of the carboxylic acids used.
If tartaric acid is used as the complexing agent in eluents then it is chiefly the neutral
MeL 1:1 complexes which are formed with the alkaline earth, transition and heavy metals
together with a lesser amount of the hydrogen tartrate complex MeHL +. For tartaric acid
eluents the following is obtained for the calculation of the αM value:
(50)
where cL is the total concentration of tartaric acid and αHL and αL are the molar fractions
of the acid anions HL– and L2–.
Apart from 1:1 complexes, some metal ions also form stable MeL 22– complexes with
oxalic acid and/or pyridinedicarboxylic acid , so that αM can be calculated as follows:
(51)
Calculation of the acid dissociation

The pH and concentration of the complexing agent in the mobile phase determine the
concentration at the ligand and therefore the extent to which the analyte is complexed.
An acid with two protons dissociates in two stages:
(52)
(53)

with the acid constants ΚS and ΚS . The molar fractions αH L, αHL and αL used to calculate the
1 2 2
αM value are obtained from the laws of mass action of the individual deprotonization stages:
(54)
(55)
(56)
3.5 Ion chromatography detection systems

Different methods are used for the detection of substances in the HPLC sector. The selection
of a suitable detector must always be made in accordance with the analytical problem to be
solved. The demands placed on the detector can be summarized as follows:
• high measuring sensitivity and short response times
• measuring signal proportional to the analyte concentration (large linear range)
• small baseline changes (drift)
• low background noise
• as small a volume as possible to reduce peak broadening
A general differentiation is made between selective and non-selective detectors. Whereas a
selective de-tector responds directly to a property of the analyte, non-selective detectors react
to an alteration to one of the physical properties of the whole elution system caused by the
analyte. As the detectors used in ion chromatography do not differ in principle from those used
for «conventional» HPLC the most important detection systems will at least be mentioned in
this section. The universal and most frequently used IC detector is the conductivity detector.
3.5.1 Electrochemical detection methods
Conductivity detection
Conductivity detection, also known as conductometric detection, has a market share of about
55% in the ion chromatography sector [4]. If the number of ion chromatographs which have been
sold is taken into account then this share is probably much higher today. Conductivity detection is a
non-selective detection principle; in this case both direct and indirect detection determinations are
possible. As aqueous electro-lytes are frequently used as the mobile phase in ion chromatography,
the detector must be able to respond to the relatively small changes in the total conductivity of the
eluent caused by the analyte ions. By the use of so-called suppression techniques the self-
conductivity of particular eluents can be dramatically re-duced; in the case of strong acid anions it is
also possible to achieve a considerable improvement to the sensitivity.
30 Metrohm
Monograph
The conductivity κ is determined technically as the reciprocal of the resistance R which a
liquid produces between two electrodes with an area of A at a distance of L.
(57)
The equivalent conductivity Λ of a solution can be determined as:

(58)
The limiting conductivity Λ∞ and the variation of conductivity with concentration can be
determined by using Equation 59. Constants A and B are empirical substance constants.
(59)
The conductivity of an electrolyte is obtained by adding the ionic conductivities Λ –Anion and Λ+Cation together:
(60)
Figure 12 Construction of a conductivity measuring cell.
According to Kohlrausch's law, the conductivity of a dilute solution is proportional to the

sum of the conductivities of all the ions multiplied by their concentrations.
(61)
where κ is the conductivity in S cm –1, Λ the limiting conductivity in S cm 2 (z mol)–1 and c

the concentration in z mol L –1 (z corresponds to the charge on the ion). The factor 1000
comes from the fact that 1 liter is equal to 1000 cm3.
The change in conductivity caused by the analyte is proportional to its concentration in the eluate,
(62)

where S and E stand for the analyte and eluent ion respectively. As in conductivity detection the alteration
in conductivity is measured, in anion chromatography only small alterations in conductivity occur at high
basic conductivities. This means that keeping the basic conductivity as low as possible is advantageous.
Figure 13 Changes in the eluate

conductivity during the separation
of a multi-substance mixture by
ion chromatography. The plots
are for an eluent with high (red)
and low (blue) conductivity
In ion chromatography the conductivity of an eluate can either be determined directly or after passage
through a suppressor. These versions are known as the single column and suppressor techniques. The
version which is to be preferred can be determined by carrying out a rough calculation.
If direct conductivity detection is used in anion chromatography then the sensitivity κ Peak of the
measure-ment depends on the difference in the equivalent conductivities of the
analyte and eluent anions; with chloride as the analyte and carbonate as the eluent
anion the following equations are obtained:
κ Peak ≈ c Analyte
(Λ-– – – Λ
-– 2– ) ⇒ κ Peak
≈c Analyte
(76 – 72)
Cl
CO3
κ ≈c •4
Peak Analyte
If the eluent is adapted to the requirements of direct conductivity detection then the
following sensitivity is obtained by replacing the carbonate eluent by a phthalate eluent:
κ Peak ≈ c Analyte
(Λ-– – – Λ-– ) ⇒ κ Peak
≈ c Analyte (76 – 38)
Cl Phthalate
κ ≈c • 38
Peak Analyte
If, on the other hand, the conductivity of the eluent is chemically suppressed (exchange of the
eluent cations for H+), the sensitivity depends on the sum of the equivalent conductivities of
the analyte anion and the H+ ion; the following then applies for Cl– as analyte anion:
κ Peak ≈ c Analyte + +)
(Λ-– – + Λ ⇒ κ Peak ≈ c Analyte (76 + 350)
Cl H
κ ≈c • 426
Peak Analyte
From this rough calculation it can be seen that, for anions, direct conductivity detection is
less sensitive by a factor of 10 than conductivity detection after chemical suppression.
32 Metrohm
Monograph
In a similar way the following rough calculation can be made for cation chromatography, with
Na+ as the analyte and H+ as the eluent cation. In the case of direct conductivity detection
(NaCl/HCl) the following equations are obtained for the sensitivity κ Peak of the measurement:
+ +
κ Peak
≈cAnalyte
(Λ + –Λ + )⇒ κ
Peak Analyte
≈c (50 – 350)
Na H
κ ≈c • (–300)
Peak Analyte
If, on the other hand, the conductivity of the eluent is chemically suppressed (exchange
of the eluent anions Cl– for OH–), the following applies:
κPeak ≈ cAnalyt (Λ+Na+ + Λ-–OH–) ⇒ κPeak ≈ cAnalyt (50 + 198)
κ ≈c • 248
Peak Analyt
This means that the sensitivity is better for direct conductivity detection of cations than
for conductivity detection after chemical suppression.
Table 2 Equivalent conductivity Λ∞ of several
ions
Cations Λ+ (S cm2 eq–1) Anions Λ– (S cm2 eq–1)

H+ 350 OH– 198
Li+ 39 F– 54
Na+ 50 Cl– 76
K+ 74 Br– 78
NH4+ 73 I– 77
½ Mg2+ 53 NO2– 72
½ Ca2+ 60 NO3– 71
–
½ Sr2+ 59 HCO3 45
½ Ba2+ 64 ½ CO32– 72
½ Zn2+ 52 H2PO4– 33
2–
½ Hg2+ 53 ½ HPO4 57
1
½ Cu2+ 55 /3 PO43– 69
½ Pb2+ 71 ½ SO42– 80
½ Co2+ 53 CN– 82
1 3+
/3 Fe 70 SCN– 66
N(Et)4+ 33 Acetate 41
½ Phthalate 38
Propionate 36
Benzoate 32
Salicylate 30
½ Oxalate 74

Suppressors for ion chromatography can be arranged either as discontinuously working packed-bed
sup-pressors as shown in Figure 14 or as continuously working membrane suppressors. The
packed-bed suppressor in the revolver version used by Metrohm has three identical suppressor
units; while one unit acts as the suppressor the second is regenerated and the third is rinsed with
water. After an analysis has been carried out the revolver is rotated by 120 degrees and the column
which has just been rinsed is used as the suppressor. This makes quasi-continuous work possible.
Figure 14 Schematic construction of a packed-bed

suppressor for quasi-continuous work
The membrane suppressor shown in Figure 15 allows continuous work but, as a result of the
use of ion exchange membranes, is susceptible to occupation of the membrane surface; this
reduces the suppres-sion capacity and finally causes the suppressor to cease functioning.
Figure 15 Schematic construction of

a continuously working membrane
suppressor
Amperometric detection
In principle voltammetric detectors can be used for all compounds which have functional groups
which are easily reduced or oxidized. The amperometric detector is the most important version. In
this detector a certain potential is applied between a working electrode and a reference electrode. If
an electrochemi-cally active analyte, whose half-wave potential is such that the applied potential
causes reduction or oxidation, now passes between the electrodes then a current will flow; this
represents the measuring signal. Amperometry is very sensitive; the conversion rate is only about
10%. Apart from a few cations (Fe 3+, Co2+) it is chiefly anions such as nitrite, nitrate, thiosulfate as
well as halogens and pseudohalogens which can be determined in the ion analysis sector. The most
important applications lie, however, in the analysis of sugars by anion chromatography and in
clinical analysis. Owing to its different working prin-ciple, the coulometric detector provides a
quantitative turnover without, however, there being any in-creased sensitivity.
34 Metrohm
Monograph
Potentiometric detection
In potentiometric detection ion-sensitive electrodes are used, some of which have a very high
selectivity. Despite their necessary high degree of miniaturization the sensors must function reliably;
this still causes problems in practice. This is the reason why up to now potentiometric detection, in
the ion chromatogra-phy sector, is limited to a few special applications.
3.5.2 Spectroscopic detection methods
Photometric detection
Because of its extremely wide range of application photometric or UV/VIS detection is the most
important detection method used in HPLC, as virtually all organic molecules contain chromophore groups
which are able to absorb in the UV or VIS spectrum. A requirement is that the eluent used does not absorb
in the range of wavelengths used. With direct detection at the maximum absorption of an analyte UV/VIS
detec-tion is practically selective. Substances which either only have a limited absorption or no absorption
at all in the particular wavelength range can be determined indirectly by measuring the maximum
absorption of the elution system. In the field of inorganic ion analysis UV/VIS detection plays a smaller
role. While of the simple anions only analytes such as nitrate, bromide or iodide absorb, important
analytes such as fluoride, sulfate or phosphate can only be measured indirectly [4]. Many cations do not
absorb at all, but multivalent and transition metals in particular can be converted in a post-column
derivatization with chelate formers such as 4-(2-pyridylazo)-resorcinol (PAR) or Tiron to form colored
complexes. Redox-active analytes such as bromate and other oxohalide ions can be analyzed by UV/VIS
detection after undergoing a post-column reaction with an electrochemically active indicator.
Fluorescence detection
Fluorescence detection is very sensitive and is always possible whenever analytes can be excited
to fluoresce; this is mainly the case for organic compounds with extended π-electron systems. This
means that typical applications are found in the fields of clinical and organic analysis. In connection
with ion chromatography, fluorescence detection is used in a few special cases, as only particular
ions such as Ce3+ are directly accessible and non-fluorescing ions can only be detected after
derivatization. It is ex-tremely difficult to develop elution systems for this detection method because
of its great susceptibility to interference by contaminants. Furthermore the linear range of the
method is relatively small (often less than two powers of ten) owing to self-absorption effects.
Coupling techniques
So-called coupling techniques represent the link-up of a chromatography system with an
independent analytical method, usually spectrometry [3]. In recent years these methods have
greatly increased in importance. Although the coupling of a gas chromatograph with a mass
spectrometer (GC-MS) is well established, coupling HPLC with spectrometric methods causes great
technical problems. In classical HPLC, i.e. the analysis of organic compounds, couplings with a
mass spectrometer (LC-MS), IR-spec-trometer (LC-FTIR) and nuclear magnetic resonance
spectrometer (LC-NMR) are available [3]. In particu-lar, powerful atomic spectrometric detectors are
used in ion chromatography (IC). Examples are atomic emission and mass spectrometry with
inductively coupled plasma (IC-ICP-AES, MS); as a result of their element specificity and sensitivity
these provide excellent performance data. This is the reason why, de-spite their relatively high
costs, such systems are used for the analysis of species and in the ultratrace analysis of elements.

Refractometry
Differential refractometry is a further detection method based on an optical method. This detector is also
called an RI detector (from Refractive Index). It is wholly non-specific and is suitable for universal use as
the quantity measured is the change in the refractive index of the pure eluent caused by the analyte.
However, the great temperature sensitivity of the refractive index means that the method is very suscep-
tible to interference. Provided that the temperature is absolutely stable the method has a linear range of
three powers of ten. As simple inorganic ions have an extremely low refractive index they can only be
determined indirectly by using eluents to which strongly refracting compounds have been added.
3.6 Stationary phases in ion chromatography

Efficient ion chromatography requires packing materials which are made of very small particles which are
as spherical as possible and have a narrow particle size distribution range. Particles with diameters from 2
to 10 µm are used. In addition the packing material should display ion exchange kinetics which are as
rapid as possible. Apart from the particle this also determines the performance of ion exchangers.
3.6.1 Overview of common stationary phases

A wide range of different organic and inorganic materials is suitable for use in ion
chromatography. What they all have in common is that their surfaces bear functional groups
which are able to exchange ions. The following classes of substances can be used [4]:
• Modified organic polymer resins
• Modified silica gels
• Inorganic salts (e.g. polyphosphates)
• Glasses
• Zeolites
• Metal oxides (e.g. Al2O3)
• Cellulose derivatives
Apart from these, systems with a very complex constitution are also possible, such as anion
exchangers with functional groups consisting of alkali metal ions bound to a stationary phase by
crown ethers. In practice the most important representatives are based on modified organic polymer
resins and silica gels. Figure 16 provides an overview of separation materials used in IC:
Figure 16 Commonly used stationary phases in ion chromatography [4]
36 Metrohm
Monograph
All stationary phases can be further differentiated according to their type of application
(anion or cation chromatography) or the structure of the functional group. The packing
materials based on silica gel were originally used for ion chromatography. Although they
have a very good separating performance and are mechanically extremely stable, their
chemical instability means that they can only be used in the pH range 2 to 7.
From about 1980 onwards ion exchangers became available which were based on organic
polymers and could be used in ion chromatography; these were manufactured by modifying
commercially available adsorber resins. Today the packing materials used are normally based
on either polystyrene-divinylbenzene copolymers (PS-DVB) or methacrylate polymers (MMA).
These two basic copolymer types mainly differ in their polarity. The PS-DVB copolymers
are completely non-polar and represent RP phases whereas the MMA polymers are
relatively polar. This situation is an advantage in IC as the more polar separation phases
have a lesser tendency to secondary interactions such as adsorption.
The greatest advantage of the organic polymer resins is their great chemical stability throughout the
whole pH range. After initial problems had been overcome their chromatographic efficiency is
similar to that of the silica gels. However, MMA phases may have a limited mechanical stability, this
could limit the length of the separation column used or the maximum possible eluent flow rate.
In ion chromatography today two types of stationary phases are used which differ in principle;
surface functionalized ion exchangers and pellicular ion exchangers. In the first type the functional
groups are located directly on the polymer surface or in the pores; the pellicular materials have very
small particles (also surface functionalized) which are bound to larger central particles [4]. The
bonding can either be mechanical or result from hydrophobic or electrostatic interactions. Figure 17
shows the arrangement of the two types of packing material using anion exchangers as examples.
Figure 17 Structure of surface functionalized (a) and pellicular anion exchangers with mechanical bonding (b)
The pellicular packing materials have a higher chromatographic efficiency as the diffusion
paths are kept very short owing to the greater distance of the functional groups from the base
material; this results in excellent mass transfer. However, the chemical stability of these
separation phases is considerably less than that of the surface functionalized materials.

3.6.2 Stationary phases in anion chromatography
The functional group used in anion chromatography is normally produced by converting an
anchor group with a suitable amine. This produces ammonium ions which are fixed on the
polymer surface. Functional groups based on nitrogen are virtually the only ones used for the
separation of anions by IC. This is based chiefly on their unusually good chemical stability and
the almost unlimited number of possible substituents at the nitrogen atom.
Ammonium groups are generated on polymer surface by converting an anchor group with an amine.
The alkyl residues at the positively charged nitrogen can be varied over a wide range. In the simplest case
R = H and a primary (1°) ammonium ion is formed. However, this can be deprotonated at higher pH values
and loose its charge. With this type of packing material the exchange capacity depends on the pH of the
eluent which is why they are also known as weakly basic. If the hydrogen atoms are now substituted
successively by alkyl groups then first secondary (2°) and then tertiary (3°) ammonium groups are formed;
these can also be deprotonated. Only when all the residues R consist of alkyl groups is the capacity or
charge irrespective of the pH of the eluent and a strongly basic quaternary (4°) anion exchanger is ob-
tained. In chromatography a pH-independent capacity is normally the aim so that only completely alkylated
materials are used. For special applications such as protein analysis or preconcentration techniques
weakly basic materials are also used.
The two most important functional groups in anion chromatography are derived from
trimethylamine (TMA) and dimethylethanolamine (2-dimethylaminoethanol, DMEA). Practically
all commercially available separation materials use one of these two groups. TMA groups are
also known in the literature as Type I groups, DMEA groups as Type II. Other functional
groups with a close relationship to those mentioned above are shown in Figure 18:
Figure 18 Overview of the most important functional groups which are mentioned in this work
TMA: Trimethylamine (Type I) DEMA: Diethanolmethylamine
EDMA: Ethyldimethylamine TEA: Triethanolamine
DMEA: Dimethylethanolamine (Type II)
In commercial materials, which are usually derived from Type I or II, the exact
arrangement of the func-tional groups is a well-guarded secret [4].
3.6.3 Stationary phases in cation chromatography

In cation chromatography both materials based on silica gel and polymer-based
materials are in use. In contrast to anion chromatography with its usual alkaline eluents
the conditions for cation chromatography also allow the use of silica gels.
38 Metrohm
Monograph
3.6.4 Cation exchangers based on silica gel
With cation exchangers based on silica gel a differentiation is made between directly
functionalized mate-rials and those which are coated by a polymer.
Practically the only reports concerning functionalized materials are about strongly acidic exchangers with a
sulfonic acid group [a2,a4]. These have a good chromatographic efficiency, but are unsuitable for the
simultaneous determination of alkali metals and alkaline earths owing to the large differences in affinity.
With polymer-coated silica gels, the so-called Schomburg phases, the silicate surface is coated with
a "prepolymer" which is then immobilized by cross-linking. By subsequent functionalization various
different types of exchanger can be realized. In order to obtain weakly acidic cation exchangers
polybutadienemaleic acid (PBDMA) is used, this is then radically cross-linked in-situ [30]. As a result
of the thin polymer layer of about 1 to 5 nm [31] the analyte diffusion paths are short so that a high
degree of chromatographic efficiency is the result.
A large number of applications for silica-gel-based ion exchangers exist. The simultaneous
separation of alkali metals and alkaline earths is one of the most frequent applications; the
separation of transition metal and heavy metal ions is also possible. However, several
disadvantages prevent the universal use of ion exchangers based on silica gels:
• At pH < 2 the bond between the silicon matrix and the functional group becomes increasingly
weaker; this leads to a gradual erosion of the functional groups and a loss in capacity.
• At pH > 7 the solubility of the silica gel increases considerably; this results in a reduction in the
mechanical stability of the packing, particle break-up and a dead volume at the start of the column.
3.6.5 Cation exchangers based on organic polymers

Resins produced by styrene-divinylbenzene copolymerization are mainly used as the matrix. The
limita-tions mentioned for silica gel exchangers do not exist here; they can be used over the whole
pH range of 0–14 and are also inert to fluoride. Although their pressure resistance is less than that
of silica gels it is generally still adequate, with the exception of a few methacrylate resins.
The majority of commercially available cation exchangers use sulfonic acid groups as the functional
groups. These can be bound to the aromatic system either directly or via a spacer whose length is
variable. Sulfonic acid exchangers with spacers have a considerably better chromatographic
efficiency; the spacer length is of secondary importance. They are not suitable for the simultaneous
determination of alkali metals and alkaline earths owing to the large differences in affinity.
3.6.6 Pellicular cation exchangers

As well as the directly functionalized resins pellicular exchangers are also available. They have a double
layer arrangement as it is not possible to present a completely aminated substrate particle. This is why a
fully sulfonated substrate particle is first surrounded by a layer of aminated and then by a layer of sul-
fonated latex particles. Fixing takes place via electrostatic and van der Waals interactions. The relatively
large diameter of the substrate particles (10–30 µm) results in a comparatively low counterpressure. The
small diameter (20–250 nm) of the latex particles allows short diffusion paths with correspondingly rapid
exchange processes and therefore a high separating column efficiency. The disadvantage of pellicular
materials is their sensitivity to organic solvents [32] and to mobile phases with a high ionic strength as in
this case the latex particles are gradually displaced.

The simultaneous determination of alkali metals and alkaline earths is possible by using a modified version
in which the aminated layer is covalently bound. However, the differences in selectivity between potas-
sium, magnesium and calcium are unnecessarily large so that relatively long analysis times are required.
This can be traced back to the strongly acidic sulfonic acid groups which are used.
3.6.7 Stationary phases in ion exclusion chromatography

The choice of stationary phases for IEC is very limited. The formation of the Donnan membrane by
disso-ciated functional groups is important for the separation process. Their number should be
relatively high. In addition the packing material should avoid analyte adsorption on the stationary
phase as much as pos-sible. As the analytes are mainly from the carboxylic acid and sugar groups,
as polar a surface as possible is the aim. Practically no demands are placed on the kinetics of the
ion exchange reaction as the separation is based on an exclusion mechanism. Low cross-linked
PS/DVB polymers are almost the only ones used; these are completely sulfonated.
3.6.8 The meaning of the capacity of ion exchangers

Apart from the sort of matrix and the type of functional group, the exchange capacity Q is
the decisive quantity for characterizing ion exchangers. It provides information about the
number of places which are available for ion exchange.
The exchange capacity is normally given in grams of dry packing material, either in
microequivalents (µeq/g) or micromols (µmol/g) [2]. Other information is also normally given [33].
For analytical purposes ion exchangers can be divided roughly according to their capacity into:
• low-capacity materials: Q < 100 µmol/g
• medium-capacity materials: 100 < Q < 200 µmol/g
• high-capacity materials: Q > 100 µmol/g
The separation phases used in classical ion exchangers are all high-capacity types with 3 to 5 mmol/g [4].
The above definition of the capacity is based on a complete equilibrium being attained between the
station-ary and mobile phases; this is why it is also known as the static capacity. In contrast, the
dynamic (effective) capacity is understood to be the number of functional groups which are actually
available during a chromatographic process. It is always smaller than the static capacity [2,4].
The exchange capacity can be determined in different ways [33]:
• volumetrically or titrimetrically
• by elemental analysis
• by determining retention times
All the methods provide different values for Q for the same material. Volumetric methods are most fre-
quently used in practice. For anion exchangers a packed separating column or a defined amount of resin
is loaded, e.g. with chloride solution. After the residual chloride has been washed out the column or resin
can be eluted with nitrate. The amount of chloride eluted, which corresponds to the static exchange
capacity under equilibrium conditions, can be titrated against AgNO 3 solution and quantified.
The pH dependency of ion exchangers can usually be neglected. With cation
exchangers the capacity of the weakly acidic carboxylic acid groups (R-COOH) is only
given at higher pH values (deprotonation), while the strongly acidic sulfonic acid groups
(R-SO3H) are always completely deprotonated and provide a pH-independent capacity.
40 Metrohm
Monograph
In combination with the retention models (Section 3.4) the importance of Q for the selection of the
elution and detection systems becomes obvious. Universal conductivity detection was practically
impossible to realize with eluents with a high ionic strength, no matter which special technique was
used. This is the reason why, since the introduction of ion chromatography in 1975, virtually only
low-capacity separating columns have been used. Up to now high-capacity ion exchangers have
only been described in IC appli-cations in combination with detection techniques which are not so
strongly limited by the elution system, such as UV/VIS detection [2,4].
While low-capacity separating materials are very suitable for the analysis of samples with a low
ionic strength and therefore a low matrix load, at higher ionic strengths they rapidly reach their
limits. Overload effects occur because of their low number of functional groups; these result in
deformed peaks and a dramatic drop in efficiency. Problems also occur if the analytes are present
in very different concentra-tions; this is almost always the case in ultratrace analysis.
3.7 Eluents in ion chromatography

As in all separations by liquid chromatography, the mobile phase is also the easiest
parameter to alter in ion chromatography in order to influence the separation. In contrast,
the separating column and the detec-tion system are in most cases predefined.
The choice of a suitable elution system can be made by using a wide range of criteria. In anion
chromatog-raphy the following parameters must be taken into account, among others [4]:
• Compatibility with the detection method
• Chemical nature and concentration of the eluent ion
• pH
• Buffer capacity
• Organic solvent content (modifiers)
In the relevant literature [2,4,5] the discussion about the mobile phases mainly takes place
from the point of view of whether they are suitable for the so-called single column or for the
suppressor technique. This will also be the case below, even though the focal point of the
subject of this work is the exchange capacity Q of the separating column. A brief explanation
of the terms «single column technique» and «suppressor technique» is given first. As in the
previous section, the observations are mainly limited to anion chroma-tography.
3.7.1 Anion chromatography
Single column technique

In the single column technique, which was established in ion chromatography by Gjerde and
colleagues in 1979 [33], the outlet of a separating column is directly connected to a detector; this
corresponds to the classical arrangement of an HPLC apparatus. To distinguish it from the second
main version of IC this technique is also known as «non-suppressed ion chromatography». The
eluent containing the analytes leaves the separating column and is not altered chemically. The
number of possible elution systems with different chemical characteristics is almost unlimited. Apart
from the separation problem itself, only the compatibility of the eluent with the detector needs to be
taken into account. For example, if direct UV detection is to be used then the eluent must not
absorb in the relevant spectral range. In the single column technique no limitations are placed on
the detection system so that in principle all the usual HPLC detec-tors could be used.

For low-capacity anion exchangers (Q < 100 µmol/separating column) a whole range of
eluents with different chemical characteristics are available for the single-column technique.
The concentration of the eluents is normally in the lower mol/kg range or even below. Among
other things, the substance classes mentioned below can be used [4]. In special cases
complexing agents such as EDTA or borate-mannitol complexes can also be used.
• Aromatic carboxylic acids
• Aliphatic carboxylic acids
• Sulfonic acids
• Alkali hydroxides
• Inorganic acids such as H2SO4, HCl or H3PO4
The most important class of compounds are the aromatic carboxylic acids and their salts.
The represen-tatives which are most frequently used are shown in Figure 19.
Figure 19 Structures of the most important aromatic carboxylic acids used with the single column technique.
This class of substances is used so frequently as the solutions of the acids and their salts have a very high
elution power combined with a relatively small self-conductivity, so that they can be used for direct con-
ductivity detection. With multi-base acids the charge and therefore the elution power can be controlled via
the pH. However, this must be maintained very accurately. Aromatic carboxylic acids have a high absorp-
tion in the UV spectrum so that they can be used advantageously in indirect UV/VIS detection.
For aromatic sulfonic acids such as p-toluene sulfonic acid the same statements apply in
principle; these are always present in a deprotonated state and therefore possess no
buffer capacity. Their elution power can only be controlled via the concentration.
Aliphatic carboxylic acids such as oxalic acid and citric acid have a high self-conductivity but are UV-
transparent, so that they can be used for direct UV/VIS detection. This also applies to aliphatic sulfonic
acids, of which methanesulfonic acid is the one which is most frequently used. The higher homologues of
both classes of compounds with their long hydrocarbon chains and the low equivalent conductivities with
which this is associated offer the possibility of being used for direct conductivity detection [2,4].
Alkali hydroxides have only a very limited use in the single column technique, as the OH – ion has the
lowest affinity to quaternary ammonium groups of all possible eluent anions. As a result high eluent
concentra-tions are required even at low capacities so that at the best only indirect conductivity detection
can be used. In contrast, UV/VIS detection is easily possible, although the basically UV-transparent
hydroxide ion has a distinct absorption below 220 nm at higher concentrations.
42 Metrohm
Monograph
If inorganic acids or their salts are used then their virtually complete dissociation and associated high
conductivity means that only photometric detectors can be used. If phosphoric acid or phosphates are
used then the buffer capacity and the elution power can be controlled via the pH of the eluent.
Most of the eluents mentioned here also allow the use of other detection systems such as
amperometry, fluorimetry or coupling techniques. If you wish to use the elution systems
mentioned above with these detectors please refer to the relevant literature [2,4,5].
Suppressor technique
The suppressor technique is the detection technique originally used when IC was introduced [1]. In con-
trast to the single column technique, this method uses only conductivity detection. In the suppressor
technique a so-called suppressor is inserted between the separating column and the detector‚ which is
why this technique is also known as «suppressed ion chromatography» [2,4]. Both the eluent and the
analytes are chemically modified in the suppressor, this is of particular importance with respect to the
subsequent conductivity detection. The suppressor has the task of reducing the self-conductivity of the
eluent and, if possible, of increasing the detectability of the analytes.
The principle of chemical suppression is shown in Equations 63 and 64 for an anion
chromatography application. An NaHCO3 eluent is used, the chloride ion is the analyte.
Suppression is carried out with a strongly acidic H+-form cation exchanger.
(63)
(64)
In the simplest case the suppressor unit consists of a column inserted after the separating column,
which is where the older term «two-column technique» originates. The eluent sodium hydrogen
carbonate is neutralized according to Equation 63, as the sodium ions are replaced by protons. This
dramatically lowers the self-conductivity of the eluent. The analyte Cl – itself is not altered (Equation
64), but its counter-ion Na + is exchanged for H+, which has a considerably larger equivalent
conductivity [19]. As the detector records the sum of the conductivities of the analyte and counter-
ion as the signal, the two reactions which take place result in a clearly improved sensitivity.
The columns with H+-form cation exchangers originally used as suppressors made a
considerable contri-bution to broadening the peaks. In addition they could only be operated
discontinuously, as the cation exchanger had to be regenerated. This is why continuously
operating membrane suppressors are mainly used today; in these the regenerating agent,
usually dilute sulfuric acid, and eluent are led past each other in a counterflow principle [6].
Despite its advantages the suppressor technique also has several crucial disadvantages. In practice only
those eluents which are based on alkali hydroxides or carbonates can be successfully suppressed in
anion chromatography. Anions of weaker acids, e.g. acetate or fluoride, are almost completely protonated
after the suppression reaction, so that their detectability is much lower when compared with the single
column technique. High-valency cations must be removed before the analysis as they form insoluble
hydroxides which precipitate out on the separating column and can block it.
As has already been made clear, the suppressor technique is synonymous with chemical suppression of the
eluent and the use of direct conductivity detection [2,4]. This technique is unusually widespread in anion
chromatography, chiefly because in many cases it is more sensitive than the direct conductivity detec-tion used in
the single column technique. The self-conductivity of the classical eluents (e.g. 2 mmol/kg

phthalate, pH = 8) in the single column technique is about 200 µS/cm. For suppressible
eluents it is usually lower by at least one power of ten.
Chemical suppression of self-conductivity is only possible for a few eluents. These are solutions of [4]:
• Alkali hydroxides
• Alkali carbonates and hydrogen carbonates
• Borates (e.g. B4O72–)
• Amino acids
In practice, of the eluents mentioned above only the alkali hydroxides and carbonate buffers are of
any great importance, which means that the choice of potential mobile phases is very limited.
The hydroxide ion is an extremely weak eluent ion, so that even with low-capacity separating
materials work must be carried out at high concentrations above 50 mmol/kg. If very polar
functional groups are used then the relative retention force of the OH – ion can be considerably
increased by utilizing the hydrox-ide selectivity. With OH – eluents manipulation of the retention
times or selectivities can only be carried out via the concentration.
The use of alkali carbonates and alkali hydrogen carbonates permits considerably more flexible elution
systems. Both species, HCO3– and CO32–, are present as carbonic acid H 2CO3 after suppression; this is
only dissociated to a very small extent. In its elution power hydrogen carbonate is only slightly stronger
than hydroxide, whereas carbonate is a relatively strong eluent. Both anions are normally used together;
this results in an eluent with a buffer effect whose elution power can be easily controlled via the concentra-
tions of the two components and the ratio of their concentrations. Because of the charges on the eluent
species the selectivity for monovalent and divalent analytes can be influenced very selectively. The con-
centration ratio of the two eluent ions can also be adjusted very accurately via the pH, this is why the pH
range used for HCO3–/CO32– eluents is between 8 and 11. Just as for OH – eluents, elution can be acceler-
ated by the use of stationary phases with polar functional groups.
Both elution systems can only be used successfully with surface functionalized anion
exchangers when either the matrix (methacrylate copolymers) or the functional group has a
high polarity. For separating columns based on PS-DVB very poor peak symmetries and long
retention times have been observed for weak analytes (nitrate, bromide) even when polar
functional groups are used. With pellicular materials these effects are not so marked, which
explains their exceptionally widespread use in the suppressor technique [2,4].
3.7.2 Cation chromatography
3.7.2.1 Cation chromatography of alkali, alkaline earth and ammonium ions with conductivity detection
In the separation of alkali metal and ammonium ions as well as short-chain aliphatic amines on sulfonated
separation phases by ion chromatography, mineral acids such as HCl or HNO 3 are mainly used as the
eluent [4]. The acid concentration of the eluent depends on the type and capacity of the cation exchanger
used and is a few mmol/L. Divalent cations such as the alkaline earths cannot be eluted with mineral acids
as they have a distinctly higher affinity to the stationary phase and a dramatic increase in the acid concen-
tration would make detection too insensitive or mean that suppression could no longer be guaranteed. As
an alternative an organic base such as ethylenediamine can also be used for the separation of alkaline
earth ions. At low pH values this is protonated and is present as a divalent cation.
The simultaneous analysis of alkali and alkaline earth cations on strongly acidic cation exchangers is
mainly carried out with eluents which contain hydrochloric acid and 2,3-diaminopropionic acid [2]. By
44 Metrohm
Monograph
varying the pH it is possible to alter the degree of protonation of the amino groups and
therefore the elution power of the 2,3-diaminopropionic acid (see section 3.4.2).
In ion chromatography systems without suppression, weak organic acids can also be
used as eluents in addition to the mineral acids. Organic acids used are e.g. oxalic acid,
citric acid, tartaric acid. Complexing agents such as 2,6-pyridinedicarboxylic acid
(PDCA) and 18-crown-6 are used to selectively influence the analysis times of individual
cations.
There are two different types of conductivity detection. If the basic conductivity of the eluents is high, e.g.
with dilute mineral acids because of the high conductivity of the H + ions, then direct conductivity detection
is possible with the analytes having a clearly lower conductivity than the eluent. This means that negative
peaks are produced which, however, can be converted into a normal chromatogram by reversing the
polarity of the detector or by simple inversion. If the quality of the conductivity detector does not permit
sensitive conductivity measurements at a high level then suppression is also used for cation chromatog-
raphy. The construction of suppressors for cation chromatography is far more difficult than for anion
chromatography and they also have a much shorter working life.
3.7.2.2 Cation chromatography of transition metal and alkaline earth ions with
post-column derivatization and photometric detection
Monovalent cations such as H+ or Na+ are unsuitable for use as an eluent for the separation of transition
and heavy metal ions as the selectivity coefficients of the analytes hardly differ at the same charge
number. However, separation can be realized by the introduction of a secondary equilibrium. This is done
by using complex-forming carboxylic acids (see Figure 20) such as citric acid, oxalic acid and tartaric acid
as the eluent. Together with the metal ions these form neutral or anionic complexes (see section 3.4).
Figure 20 Various carboxylic acids as eluents in cation chromatography.
By complexing the metal cations the effective charge density of the analytes is reduced. In addition
the different complex forming constants of the individual metal ions increase the selectivity of the
separation. The elution mechanism is a result of the isoionic displacement by the counter-ion
(pushing effect) and complex formation (pulling effect) by the complex-forming ligands [4].
Figure 21 shows the equilibria between the analytes M 2+, the complexing agent L2– and
the counter-ions E+ which participate in the elution mechanism.

Figure 21
Schematic diagram of the
equilibria participating in
the exchange process
[4].
The extent of the isoionic displacement by the counter-ions E + is determined by the affinity of the cation to
the stationary phase. With monovalent counter-ions the cation with the greater affinity to the stationary
phase has a stronger eluting effect. The influence of the complexing agent can be varied by altering the pH
and concentration of the eluent. In addition the elution power can be influenced by the use of several
complexing agents as well as by using a divalent cation as the counter-ion.
Whereas both types of conductivity detection are suitable for the detection of alkali metals and alkaline
earths, transition and heavy metal ions can only be determined by direct conductivity measurement with-
out suppressor. If the suppressor technique were to be used then these metals would be converted into
(mostly) insoluble hydroxides by the suppressor reaction. Direct conductivity detection is only possible
when eluents with a low basic conductivity are used together with low-capacity cation exchangers.
This is why post-column derivatization with the formation of photometrically detectable metal
complexes is mainly used for the detection of transition and heavy metal ions. After leaving the
separating column the eluate is mixed with a metallochromic reagent in a post-reactor; this reacts
with the analytes to form colored metal complexes which can be detected photometrically. A wide
range of azo-dyes can be used as the coloring agents [2,4]; these react with a large number of
metal cations. Transition metals and lanthanoides react with 4-(2-pyridylazo)-resorcinol (PAR)
(Figure 22) to form colored complexes. Lanthanoides and actinoides can be detected by using 2,7-
bis(2-arsenophenylazo)-1,8-dihydroxynaphthalene-3,6-disulfonic acid (Arsenazo III). Pyrocatechol-
3,5-disulfonic acid (Tiron) is suitable for the post-column derivatization of aluminum.
Figure 22 Structure of the metal indicator PAR
46 Metrohm
Monograph
PAR is mainly used for the detection of transition and heavy metal ions. With Fe, Co, Ni, Cu, Zn, Mn, Pb
and Cd PAR forms colored complexes; these absorb at wavelengths from 490 to 520 nm with absorption
coefficients up to 104 L mol –1 cm–1 and can be detected photometrically. The sensitivity of the method is
based on the fact that the extinction coefficients of the metal-PAR complexes are large compared with the
absorption coefficient of the reagent at the wavelengths used.
3.7.2.3 Ion exclusion chromatography

In IEC the choice of the elution agent is, like the selection of the packing material, not very exciting.
The range extends from pure water up to dilute mineral acids. When selecting the most suitable
system it is also necessary to take the detection system into account. The most frequently used
detection systems are photometric and conductivity detection. With photometric detection dilute
sulfuric or perchloric acid are often used because of their absolute UV transparency. When applying
conductivity detection, dilute sulfu-ric acid is the eluent of choice as it yields good chromatograms
with a minimum of equipment (no sup-pressor required). In combination with a cation
chromatography suppressor dilute hydrochloric acid can be used as eluent.
The concentration of the acid in the eluent determines the degree of dissociation of the
analytes and therefore also their retention. In general the retention decreases as the
acid concentration increases. The peak shape is also influenced by the acid
concentration. For organic acids pure water is usually not suitable owing to its increasing
adsorption although it produces excellent results for carbonate and boric acid.

4 Practical section
The practical section of this textbook presents experiments which provide a detailed introduction to the
world of ion chromatography. A start is made with experiments covering the theory of ion chromatography
(chapter 4.2); the second part (chapter 4.3) continues with the determination of anions and the third and
final part (chapter 4.4) deals with the determination of organic and inorganic cations.
In principle the experiments can be carried out on any ion chromatograph. However, the
equipment level of the instrument should still fulfil the following requirements:
• Low-pulsation double-piston pump, if possible working without an external nitrogen or helium supply
• Flow control meeting column requirements
• Electric injection valve
• Possibility of connecting various sample loops and preconcentration columns
• Electronic suppression for anions and cations
• Chemical suppression for anions
• Temperature-stabilized conductivity detector, if possible better than ±0.01 °C
• Thermally and electronically shielded housing
• Anion and cation operation
• PC control is recommended
All the modular or compact IC systems from Metrohm fulfil the above requirements as a
matter of course. However, the 792 Basic IC is specially designed for training and teaching
and is therefore recommended for carrying out the experiments described below.
Figure 23 The Metrohm 792 Basic IC: specially

developed for training and teaching
4.1 Information about the practical work

Bacterial growth
In order to prevent bacterial growth, the eluent, rinsing and regenerating solutions should always be made
up freshly and not used over a longer period of time. If bacterial or algal growth should nevertheless occur
then 5% methanol or acetone can be added to the eluent. If membrane suppressors are used this is not
48 Metrohm
Monograph
possible as these could be destroyed by organic solvents. However, the Metrohm
Suppressor Module «MSM» is 100% solvent-resistant.
Cation analysis
In each analysis carried out the sample must be acidified (pH 2.5 … 3.5) with nitric acid
(approx. 100 µL 2 mol/L HNO3 to 100 mL sample), as otherwise no reproducible results
will be obtained for divalent cations.
Chemical grade
All the chemicals used should have at least the grades p.a. (analytical grade) or puriss.
(extra pure). Any standards used must be specially suitable for ion chromatography; for
example, sodium salts should be dissolved in water, not in acid.
Contamination sources
All solutions, samples, regenerating solutions, the water and the eluents used should be free of particles
as these will block the separating columns in the course of time (rise of column pressure). This is espe-
cially important when preparing the eluents as these flow through the column continuously (500 to 1000
mL per working day, whereas the sample throughput is approximately 0.5 mL).
Eluent degassing
In order to avoid bubble formation it is recommended that the water used for preparing the
eluent is degassed before the reagents are added to it. This can be done by applying a
vacuum from a water-jet or vacuum pump for about 10 minutes or by using an ultrasonic bath.
Environmental protection
One of the great advantages of ion chromatography is that usually aqueous media are used.
This is why the chemicals used in ion chromatography are to a large extent non-toxic and do
not pollute the environ-ment. However, if acids, bases, organic solvents or heavy metal
standards are used then care should be taken that these are disposed of properly after use.
Instrument shut-down
If the ion chromatograph is not to be used for a longer period of time (>1 week) then the
separating column should be removed and the ion chromatograph rinsed with methanol/water
(1:4). Care should be taken that all three chambers of the suppressor are rinsed.
Safety information
Protective goggles, protective clothing and, if necessary, protective gloves should be worn when carrying
out all the experiments. Be sure to observe the safety information (R/S-phrases) given for the chemicals.
Selecting a column
Most of the experiments described are carried out on very favorably priced columns – Metrosep
Anion Dual 1 for anions and Metrosep C2 for cations. These columns provide adequate separation
for all the experiments described. Of course, the Metrosep product range includes separating
columns which have a considerably better performance, but these are also more expensive.

Storing the separating columns
• Metrosep Anion Dual 1 IC anion column (6.1006.020)
For short-term storage (days) the column cartridge is stored in the closed holder. For long-term stor-
age (weeks) the column is stored in the dark in the storage vessel supplied in acetone/water (1:9).
Figure 24 Metrosep Anion Dual 1 IC column

(6.1006.020) with column holder
• Metrosep A Supp 5 IC anion column

(6.1006.530) The column is stored in the eluent.
• Metrosep C2 IC cation column (6.1010.210)
The column is stored in the eluent in a refrigerator (4 °C). It is essential that the
column does not dry out.
Figure 25 Metrosep C2 IC cation column (6.1010.210)
• Nucleosil 5SA IC cation column (6.1007.000)

For short-term storage (days) the column is stored in the eluent, for long-term storage
(weeks) in methanol/water (1:4).
• Metrosep Organic Acids column (6.1005.200)
For short-term storage (days) the column is stored in the eluent, for long-term storage
(weeks) in deionized water.
• Separating columns from other manufacturers
Please refer to the manufacturer's instructions.
50 Metrohm
Monograph
Water quality
In ion chromatography mainly aqueous media are used. This is why the water quality is crucial for good
chromatography results. If the water quality is unsatisfactory then it is certain that the results will also be
unsatisfactory. In addition there is the danger of damaging the instrument and separating column. The
deionized water used «aq. demin.» should therefore have a resistance greater than 18 MΩ and be
particle-free. It is recommended that the water is filtered through a 0.45 µm filter.
4.2 Experiments covering the theory of ion chromatography

4.2.1 Experiment 1 – Ion chromatography with and without chemical suppression
The equivalent conductivity Λ∞ is always obtained by adding together the equivalent
conductivities of all anions Λ∞− and cations Λ∞+ in the solution:
Λ∞ = Λ∞+ + Λ∞−
In principle the conductivity increases as the concentration of the electrolyte or ions
increases. A linear relationship only exists for dilute solutions, as Λ depends on the
concentration (Kohlrausch's law). The values found in tables (see chapter «Conductivity
detection») apply for Λ∞ – equivalent conductivity in infinitely dilute solutions.
The size of the equivalent conductivity depends to a great extent on the temperature (±2% /
°C). In particular, for measurements without chemical suppression, i.e. mostly against a high
background, errors caused by a change in temperature are extremely noticeable. This is why
temperature fluctuations within the detector should not be larger than 0.01 °C.
In ion chromatography without chemical suppression, in which the background
conductivity is suppressed electronically, the eluent should have as low a conductivity as
possible. The salts of weak acids such as phthalic acid, salicylic acid and benzoic acid
come into question here. A value measured without chemical suppression depends on
the difference in the equivalent conductivities of the sample ion and the eluent ion.
∆Λ ∼ (ΛP – ΛE)
Negative peaks always occur when the conductivity of the sample ion is lower than that of the eluent ion.
An example of this is the phosphate anion. At pH = 5 it is mainly present as H 2PO4–. As the equivalent
conductivity Λ∞ of the H2PO4– with 33 S*cm2/mol is lower than the equivalent conductivity Λ ∞ of the
phthalate with 38 S*cm 2/mol a small negative peak is obtained. This can be remedied by selecting a
higher pH, at which the phosphate is present as HPO 42– with an equivalent conductivity Λ∞ of 57
S*cm2/mol.
Ion chromatography with chemical suppression means that the background conductivity
is reduced chemi-cally. An eluent with a high conductivity is converted in a post-column
reaction – the suppression reaction – into an eluent with a low conductivity.
In anion analysis this is carried out by using the salts of weak acids, e.g. HCO3–, CO32–
and BO33–, in the eluent. All the cations in the eluent and in the sample are exchanged
for H+ in the suppressor. Weakly dissociated acids are formed from the eluent according
to the following reaction: Na+ + HCO3– +H+ – Na+ > H2CO3
The resulting carbonic acid is mainly present as CO 2 + H2O. As a result the residual
conductivity is very low. As the counter-ions of the anions to be determined are also
exchanged for H+ in the suppressor the following equation can be formulated:

+ +
Na+ + Cl– +H – Na > H+ + Cl–
Instead of the Na+ and Cl– which were originally present in the sample the considerably
higher equivalent conductivity of H+ and Cl– is now measured and this also against a
lower background conductivity. Theo-retically a signal can be expected which is larger by
a factor of ten than for a measurement without chemical suppression. However, in
practice only an increase in sensitivity in the range of a factor of 2 to 4 is obtained.
In contrast to a linear calibration function obtained when working without chemical suppression,
when chemical suppression is used a quadratic calibration function is obtained; this means that a
multi-point calibration is necessary for its calculation. The linear concentration range is considerably
smaller (approx. 1/20 to 1/50) than when working without chemical suppression.
Learning content
• Principles of an IC system setup
• Differences between working with and without chemical suppression
• Determination of the different sensitivities of the two methods
Experiment 1a – Measurement without chemical suppression

Table 3 Parameters – Experiment 1a
Column 6.1006.020 Metrosep Anion Dual 1 (3 x 150 mm)

Eluent 8 mmol/L phthalic acid, 2% acetonitrile; pH = 4.1 (TRIS)
Conductivity approx. 400 µS/cm
Sample Standard (fluoride, chloride, nitrite, bromide, nitrate, phosphate, sulfate)
Method exp_01_n.mtw
System anonsupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Analysis time 20 min
Loop 100 µL
Polarity +
Eluent preparation
Dissolve 1.33 g phthalic acid in 20 mL acetonitrile and a little water and make up to 1 L. Adjust
the pH to 4.1 by adding approx. 1 g TRIS (solid). Before addition of the reagents degas the
water used by applying a water-jet pump vacuum for 10 min or by using an ultrasonic bath.
52 Metrohm
Monograph
Chromatogram 1 Standard solution
Table 4 Components – Experiment 1a
Peak Component tR [min] Conc. [mg/L] No. of plates Area [µS/cm*s]

1 Fluoride 3.6 5 2310 51
2 Chloride 4.9 5 3680 71
3 Nitrite 5.7 5 3670 36
4 Bromide 6.7 10 3960 63
5 Nitrate 7.8 10 3890 74
6 Sulfate 10.9 10 3430 88
7 System peak 17
Experiment 1b – Measurement with chemical suppression
Table 5 Parameters – Experiment 1b

Eluent 2.4 mmol/L NaHCO3 / 2.5 mmol/L Na2CO3 + 2% acetone
Conductivity after chemical suppression approx. 16 µS/cm
Method exp_01_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa

53
Loop 20 µL
Suppressor Regenerating agents: 50 mmol/L H2SO4, ultrapure water
Autostep with Fill
Polarity +
Eluent preparation
Dissolve 265 mg sodium carbonate (anhydrous) and 201.5 mg sodium hydrogen
carbonate in 980 mL ultrapure water. Then add 20 mL acetone.

Table 6 Components – Experiment 1b

1 Fluoride 3.8 2 2780 48
2 Chloride 5.7 5 4100 81
System peak 6.8
3 Nitrite 7.3 5 3900 46
4 Bromide 8.6 10 4510 69
5 Nitrate 10.4 10 4480 87
6 Phosphate 11.7 10 3220 43
7 Sulfate 14.4 10 3660 113
The system peak is significantly smaller here than in experiment 1a, chromatogram 1,
and can therefore only be discerned at highly sensitive settings of the conductivity scale.
54 Metrohm
Monograph
4.2.2 Experiment 2 – Capacity of separating columns
Cut-off peaks, shark-fin-shaped peaks, altered retention times for the same ions, peaks
with tailing or fronting – all these can have a common cause: overloading the column.
Each column has a finite number of ion exchange sites. Before the sample is injected these are
completely occupied by eluent ions. When the sample is injected, ion exchange starts to take place:
Eluent ions are exchanged for sample ions and sample ions for eluent ions. As the ion species differ
in their bonding constants they elute from the column at different speeds. The required result is the
separation of the mixture of substances and therefore the chromatogram.
This process only functions perfectly if the number of exchange sites is substantially higher
than the number of bonding places required by the sample. For example, a column with a
capacity of 1 meq (milli-equivalent) can bind a maximum of 1 mmol monovalent ions.
A second effect which has a negative influence on the separation is the fact that in principle each ion can
act as an eluent ion. If the column is overloaded then many eluent ions are replaced by sample ions. This
results in incalculable alterations to the column equilibria and the separation becomes worse.
The capacity of a column can be determined by completely occupying it with chloride ions.
After a rinsing step with deionized water the chloride ions are eluted with a carbonate eluent
and then quantified by either ion chromatography or argentometric titration.
In the following experiment the chloride concentration is increased until the column is
overloaded. Some effects associated with overloading the column are described below:
→ the retention times of the following ions become shorter,
→ the peak of the dominant ion is cut off,
→ the peak of the dominant ion tails,
→ the number of theoretical plates (TP) becomes smaller,
→ the area/height ratio becomes worse (at constant area, the peak height decreases) and
→ the peak symmetry becomes poorer.

The peak symmetry also becomes poorer with blocked column frits, increased dead
volumes and as a result of absorption effects on the column material.
Learning content
• Explanation of the following chromatographic parameters: retention time, resolution,
area, number of plates, symmetry and area/height ratio
• Influence of a dominant main component on components with a much smaller
concentration: alter-ations to the above-mentioned parameters
55
Table 7 Parameters – Experiment 2

+ NaCl (approx. 1 g weighed in)
Method exp_02_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 20 µL
Suppressor Regenerating agent: 50 mmol/L H2SO4, ultrapure water
Autostep with Fill
Polarity +
Eluent preparation
carbonate in 980 mL ultrapure water and then add 20 mL acetone.
Chromatogram 3a Standard solution with a very high chloride concentration
56 Metrohm
Monograph
Chromatogram 3b Standard solution with a very high chloride concentration; enlarged part of chromatogram 3a
Remarks
Sodium chloride is weighed in. The retention times of the peaks as well as the values for
the number of plates and area may vary depending on the quantity of NaCl weighed in.
The huge chloride peak interferes with the evaluation of the following peaks. Correct identification of
the individual peaks is only possible by spiking the sample solution with the respective anions.

4.2.3 Experiment 3 – Selectivity of separating columns
If the strength of the eluent is plotted against the logarithm of the retention times of mono- and
divalent ions then a straight line is obtained. The slope of this line is greater for divalent ions than for
monovalent ions. The increase in the elution strength of the eluent therefore has a greater influence
on the retention time of the divalent ions than on the retention time of monovalent ions.
The influence can be observed on the sulfate ion. As the eluent concentration increases
the elution of sulfate is accelerated more than that of the monovalent ions.
In general divalent ions are stronger eluents than monovalent ones as they can form two
bonds with the stationary phase and therefore enter into stronger interactions with it.
At the same molarity, sodium hydroxide has a higher pH than carbonate/hydrogen
carbonate. The elution power of the OH– ion is lower compared to that of the hydrogen
carbonate as the hydroxide ion does not interact as strongly with the stationary phase.
The retention time of the phosphate ion depends strongly on the pH value. At high pH
values the equilib-rium is displaced from HPO42– towards PO43–. If sodium hydroxide is
added to a sodium carbonate eluent, this results in the retention time of the phosphate
being increased while the retention times of all other ions are shortened.
Learning content
• Comparison of eluents with monovalent and divalent anions
• Comparison of sodium hydroxide and carbonate/hydrogen carbonate eluents
• Influence of the eluent pH on the retention of phosphate
Table 8 Parameters – Experiments 3a to 3d

Eluents a) 2.5 mmol/L Na2CO3 / 2.4 mmol/L NaHCO3
b) 4 mmol/L Na2CO3 / 1 mmol/L NaHCO3
c) 4 mmol/L Na2CO3 / 1 mmol/L NaOH
d) 1 mmol/L Na2CO3 / 4 mmol/L NaOH
Method exp_03_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Analysis time a) 14 min
b) 11 min
c) 11 min
d) 24 min
Loop 20 µL
Autostep with Fill
Polarity +
58 Metrohm
Monograph
Experiment 3a – 2.5 mmol/L Na2CO3 / 2.4 mmol/L
NaHCO3 Eluent preparation

carbonate in 1 L ultrapure water.
Chromatogram 4 Standard solution – 2.5 mmol/L Na2CO3 / 2.4 mmol/L NaHCO 3


1 Fluoride 3.5 2 2733 47
2 Chloride 5.1 5 4003 81
3 Nitrite 6.6 5 3344 48
4 Bromide 7.6 10 4156 69
5 Nitrate 9.1 10 4199 91
6 Phosphate 9.8 10 2902 47
7 Sulfate 11.8 10 3442 118

Experiment 3b – 4 mmol/L Na2CO3 / 1 mmol/L
NaHCO3 Eluent preparation
Dissolve 424 mg sodium carbonate (anhydrous) and 84 mg sodium hydrogen carbonate

in 1 L ultrapure water.
Chromatogram 5 Standard solution – 4 mmol/L Na2CO3 / 1 mmol/L NaHCO3


1 Fluoride 3.3 2 2422 50
2 Chloride 4.6 5 3696 83
3 Nitrite 5.8 5 2797 47
4 Bromide 6.8 10 3970 69
5 Phosphate 7.7 10 4456 37
6 Nitrate 8.0 10 3500 102
7 Sulfate 8.7 10 3120 123
60 Metrohm
Monograph
Experiment 3c – 4 mmol/L Na2CO3 / 1 mmol/L NaOH
Eluent preparation
Dissolve 424 mg sodium carbonate (anhydrous) and 40 mg NaOH in 1 L ultrapure water.
Chromatogram 6 Standard solution – 4 mmol/L Na2CO3 / 1 mmol/L NaOH

Table 11 Components – Experiment 3c

1 Fluoride 3.2 2 2386 51
2 Chloride 4.4 5 3699 84
3 Nitrite 5.5 5 3624 47
4 Bromide 6.3 10 3997 70
5 Nitrate 7.5 10 3597 91
6 Phosphate + Sulfate 8.0 10 / 10 1772 175

Experiment 3d – 1 mmol/L Na2CO3 / 4 mmol/L NaOH
Eluent preparation
Dissolve 106 mg sodium carbonate (anhydrous) and 160 mg NaOH in 1 L ultrapure water.
Chromatogram 7 Standard solution – 1 mmol/L Na2CO3 / 4 mmol/L NaOH

Table 12 Components – Experiment 3d

1 Fluoride 3.6 2 2935 56
2 Chloride 5.0 5 4131 91
3 Nitrite 6.1 5 4096 53
4 Bromide 6.9 10 4490 74
5 Nitrate 8.0 10 4417 100
6 System peak 9.4
7 Sulfate 12.5 10 3671 126
8 Phosphate 21.2 10 2836 47
62 Metrohm
Monograph
4.2.4 Experiment 4 – Calibration, detection and determination limits in ion chromatography
Important parameters for analytical determination methods are the linear range, detection limit and deter-
mination limit. The mathematical methods for these are laid down in standards, e.g. in DIN 32645.
If chromatograms are recorded with a conductivity detector then the peak area is usually used for
evalua-tion. The peak area is proportional to the amount of substance. If the peak area is plotted
against the concentration then the calibration function is obtained. It is linear for measurements
without chemical suppression. As a first approximation it is a quadratic function for measurements
with chemical suppres-sion. Evaluation programs calculate the calibration functions automatically.
Evaluation using peak height is used preferentially for strongly tailing peaks or for
insufficiently separated peaks with strongly differing area/height ratios as in those cases
the area-based evaluation leads to large errors.
The detection limit is the minimum concentration of an analyte which can still be
detected with known statistical certainty. The theoretically smallest concentration which
can just be distinguished from a blank value is calculated.
There are two methods for calculating the detection limit:
– Blank value method:
The blank sample should be a sample which does not contain the ion to be determined but
produces a signal at the same location as the sample ion. The repeated measurement of a blank
sample gives for a concentration «0» (X value) measured values (Y values) whose mode (average
maximal frequency) is known as the blank value. By using the calibration curve the maximum Y
value is assigned to a concentra-tion value on the X axis; this is the detection limit.
– Calibration curve method:
This method is used when it is not possible to determine a blank value because the ion under investigation
cannot be detected in the sample. In the calibration curve method multiple measurements are carried out
on different concentrations of the ion. A range of confidence is then obtained from the standard deviation.
In this way the concentration «0» corresponds to a particular Y interval. The calibration function is used to
assign the Y interval to a concentration interval whose maximum value is the detection limit.
The signal/noise ratio is often used to determine the detection limit. For example, the
detection limit is defined as being the analyte concentration at which the measuring
signal is 3 times, 5 times or 7 times the baseline noise.
The determination limit is reached when the measuring error undercuts a particular value when compared
with the analytical value, e.g. 1/3. Only then will a numerical value be given in the analytical report, as
otherwise the measuring error is regarded as being too large in comparison to the analytical value. As an
estimation it can be said that the determination limit is higher than the detection limit by a factor of three.
Learning content
• What does calibration mean?
• Comparison of a single-point and a multi-point calibration – estimation of error
• Determining the system noise
• Estimating the detection limit

4.2.5 Experiment 4a – Determining anions with chemical suppression

Method exp_04_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
carbonate in 980 mL ultrapure water and then add 20 mL acetone.
Chromatogram 8 Merger – Standard solutions with different concentrations
64 Metrohm
Monograph
Peak Component tR [min] Conc. [mg/L]

Level 1 Level 2 Level 3 Level 4
1 Fluoride 3.9 1 5 25 50
2 Chloride 5.6 1 5 25 50
3 System peak 6.8
4 Nitrite 7.5 1 5 25 50
5 Bromide 8.6 1 5 25 50
6 Nitrate 10.3 1 5 25 50
7 Phosphate 11.7 1 5 25 50
8 Sulfate 14.3 1 5 25 50
Experiment 4b – Determining anions without chemical suppression


Eluent 8 mmol/L phthalic acid, 2% acetonitrile; pH = 4.1
Method exp_04_n.mtw
System anonsupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 100 µL
Polarity +
Eluent preparation
Dissolve 1.33 g phthalic acid in 20 mL acetonitrile and a little water and make up to 1 L.
Adjust the pH to 4.1 by adding TRIS (solid).

Chromatogram 9 Merger – Standard solutions with different concentrations
Peak Component tR [min] Conc. [mg/L]

Level 1 Level 2 Level 3 Level 4
1 Fluoride 3.6 1 5 25 50
2 Chloride 4.9 1 5 25 50
3 Nitrite 5.7 1 5 25 50
4 Bromide 6.6 1 5 25 50
5 Nitrate 7.7 1 5 25 50
6 Sulfate 11.0 1 5 25 50
7 System peak 17.0
66 Metrohm
Monograph
4.2.5 Experiment 5 – Altering the selectivity with the aid of crown ethers (18 Crown-6)
The retention times of cations can be altered by adding complexing agents to the eluents. The
complexing agent acts as a ligand, the analyte cation is included as the central metal ion. The
more selective a ligand with respect to a central metal ion, the stronger the influence on the
retention time. In an ideal case the retention times of the other cations will only alter slightly.
Complexing agents are used to obtain better separation of alkali metal ions. The addition of the crown ether
18 Crown-6 to the eluent leads to a better separation of Na +, NH4+ and K+. For example, the crown ether
can be added to the eluent to improve the separation between Na + and NH4+ when traces of NH4+ have to
be determined in natural waters. The increase in the retention time of K + is particularly dramatic. This can
be explained by the formation of the complex from K + and dibenzo-18-crown-6-ether (18 Crown-6). K+ fits
exactly in the «cage» of the ether. It is complexed via the electron pairs of the oxygen atoms. After
complexation, a considerably larger molecule with the same charge is separated. This means that the
retention time of the potassium is increased as a result of steric hindrance.
The name 18 Crown-6 indicates that the ring
system consists of 18 atoms of which 6 are oxygen
atoms. Crown ethers not only play an important
role in ion chro-matography, but are also used as
the ion-selective phase in potassium electrodes.
Learning content
• Effect of a very selective complexing agent on the
retention times
Figure 26 Potassium – 18 Crown-6 • Explanation of the effect in comparison with Experi-
ment 6
Table 17 Parameters – Experiments 5a and 5b
Column 6.1010.210 Metrosep C2 (4 x 100 mm)

Eluent a) 4 mmol/L tartaric acid / 0.75 mmol/L dipicolinic acid
b) 4 mmol/L tartaric acid / 0.75 mmol/L dipicolinic acid + 0.25 mmol/L
crown ether
Sample Standard (lithium, sodium, ammonium, potassium, calcium, magnesium
+ 2 mmol/L HNO3)
Method exp_05_c.mtw
System cation.smt
Flow 1 mL/min
Pressure 8 MPa
b) 17 min
Loop 10 µL
Polarity –

Experiment 5a – Eluent without crown ether
Eluent preparation
Dissolve 600 mg tartaric acid and 125 mg dipicolinic acid in 100 mL ultrapure water
under heating and then make up to 1 L with ultrapure water.
Chromatogram 10 Standard solution – Eluent without crown ether

1 Lithium 2.7 1 4270 14
2 Sodium 3.6 5 4640 18
3 Ammonium 4.2 5 3640 19
4 Potassium 6.1 10 2890 17
5 Calcium 8.1 10 2950 33
6 Magnesium 9.9 10 2310 65
68 Metrohm
Monograph
Experiment 5b – Eluent with crown ether
Eluent preparation
under heating, add 132 mg crown ether and make up to 1 L with ultrapure water.
Chromatogram 11 Standard solution – Eluent with crown ether

1 Lithium 2.8 1 4250 14
2 Sodium 4.1 5 4550 18
3 Ammonium 5.1 5 3260 19
4 Calcium 9.3 10 2170 33
5 Magnesium 10.6 10 2200 66
6 Potassium 14.9 10 1910 17

4.2.6 Experiment 6 – Altering the selectivity by using complexing agents
In the analysis of magnesium, sodium and potassium ions in the presence of zinc and
calcium ions the ability of zinc and calcium ions to form complexes with dipicolinic acid
(DPA, 2,6-pyridinedicarboxylic acid) is utilized.
Me 2+ dipicolin complex
The constant resulting from complex formation
Me2+ + (DPA) ↔ [MeDPA]2+
is different for each metal.

Depending on the pH, the following complexes can be formed (increasing removal of H+
as the pH in-creases):
acidic conditions weakly acidic conditions alkaline conditions
This means that, depending on the pH, the complex formed has either a double positive
charge, a single positive charge, or is uncharged.
The primary separation criterion on a cation exchanger column is the charge of the ions to be separated.
Uncharged complexes are not retarded whereas complexes with a 3-fold positive charge are bound very
strongly. As a result of the complex formation constant and the set pH the complex has a certain average
equilibrium charge. This equilibrium charge determines the retention time. This is the reason why divalent
metal ions can be accelerated by the addition of dipicolinic acid within a particular pH range.
There is no influence on the retention times of monovalent metal ions, which do not form
a complex with dipicolinic acid.
Learning content
• Influence of the complex formation constant on the retention time – comparison of zinc and calcium
• Behavior of other transition metal ions

• Influence of the pH value on the total charge of the complex
• Explaining the effects in comparison to Experiment 5
70 Metrohm
Monograph
Table 20 Parameters – Experiments 6a to 6d

Eluent a) 4 mmol/L tartaric acid
b) 4 mmol/L tartaric acid + 0.1 mmol/L dipicolinic acid
c) 4 mmol/L tartaric acid + 0.25 mmol/L dipicolinic acid
d) 4 mmol/L tartaric acid + 0.75 mmol/L dipicolinic acid
Sample Standard (sodium, zinc, potassium, calcium, magnesium + 2 mmol/L HNO 3)
Method exp_06_c.mtw
System cation.smt
Flow 1 mL/min
Pressure 7 MPa
b) 20 min
c) 16 min
d) 13 min
Loop 10 µL
Polarity –

Experiment 6a – 4 mmol/L tartaric acid
Eluent preparation
Dissolve 600 mg tartaric acid in 1L ultrapure water.
Chromatogram 12 Standard solution – Eluent 4 mmol/L tartaric acid

1 Sodium 4.3 5 4450 17
2 Potassium 7.8 10 2330 16
3 Zinc 11.2 5 2330 11
4 Magnesium 14.4 10 2010 63
5 Calcium 19.5 10 2640 34
72 Metrohm
Monograph
Experiment 6b – 4 mmol/L tartaric acid + 0.1 mmol/L
dipicolinic acid Eluent preparation
Dissolve 600 mg tartaric acid and 17 mg dipicolinic acid under heating in 100 mL
ultrapure water and make up to 1L.
Chromatogram 13 Standard solution – Eluent 4 mmol/L tartaric acid + 0.1 mmol/L dipicolinic acid

1 Zinc 1.9 5 554 6.7
2 Sodium 4.4 5 4390 17
3 Potassium 7.6 10 2750 16
4 Magnesium 14.8 10 2100 64
5 Calcium 17.9 10 2720 33

Experiment 6c – 4 mmol/L tartaric acid + 0.25 mmol/L
Peak Component tR [min] Conc. [mg/L] No. of plates Area [mS/cm*s]

– Zinc ~1.1 5
1 Sodium 4.3 5 4450 18
2 Potassium 7.8 10 2330 17
3 Calcium + Magnesium 14.4 10 + 10 2010 98
74 Metrohm
Monograph
Experiment 6d – 4 mmol/L tartaric acid + 0.75 mmol/L
Table 24 Components – Experiment 6d

– Zinc ~1.1 5
1 Sodium 3.8 5 4540 17
2 Potassium 6.4 10 2900 17
3 Calcium 8.5 10 2630 33
4 Magnesium 10.5 10 2190 67
Remarks
All solutions must be stored in plastic vessels. For a correct determination of sodium all contact with
glass must be avoided. The pH of the standard and sample solutions must be between 2.5 and 3.5.
After changing the eluent allow the system to run until the baseline is constant.
Chromatograms 14 and 15: Zinc is complexed by the dipicolinic acid and elutes in the front peak.

4.2.7 Experiment 7 – Preconcentration technique
In ion chromatography sample injection is carried out with the aid of a sample loop
integrated into the injection valve. Under standard conditions the volume of the sample
loop is 20 µL for anions and 10 µL for cations. With a simple IC system sample loops of
this size cover detection limits of 100 µg/L or 100 ppb without any problem.
By enlarging the sample loop, e.g. to 100 µL, the detection limits can be lowered by a factor of ten, ap-
proximately. However, larger sample volumes produce a substantially larger water peak, which affects the
evaluation of the peaks that elute early. Additionally, the the shape of asymmetric peaks becomes worse.
A simple method for lowering the detection limit by several orders of magnitude is sample
preconcentration. A preconcentration column is mounted instead of the sample loop. An increased
sample volume – 5 mL in our example – is rinsed through the preconcentration column. In principle,
this column is packed with the same material as is used in the separating column itself. This
ensures that all the anions or cations are completely retained on it as long as no eluting ions are
present. If, however, the sample contains the same anions as the eluent at the same concentration
range then the analyte ions will not accumulate on the preconcentration column.
The capacity of the preconcentration column is significantly smaller than that of the separation column. To
elute the enriched ions in as small a volume as possible, extraction by the eluent is performed counter-
current, that is, the flow direction during preconcentration is opposed to that during elution.
Usually, an alkaline eluent is used combined with chemical suppression.
Figure 27 Preconcentration technique: on the left «fill» position, on the right «inject» position
The preconcentration technique allows concentrations in the lower ppb range to be

determined on even a simple chromatography system.
76 Metrohm
Monograph
Learning content
• What is sample preparation?
• Where is the interface between ion chromatography and sample preparation?
• What is the advantage of sample preconcentration?
• What are the limits of the method?
• What is the reason for using alkaline eluents with suppression?
• What is the effect of CO2/carbonate in the sample?

Sample ultrapure water
Method exp_07_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 4 MPa
Preconcentration column 6.1006.300 Metrosep Anion
Sample volume 5 mL on preconcentration column
Autostep with Fill
Polarity +
Eluent preparation
carbonate in 980 mL ultrapure water and add 20 mL acetone.

Peak Component tR [min] Conc. [µg/L] No. of plates Area [µS/cm*s]

1 Fluoride + acetate 3.8 1+1 1620 5.4
2 Chloride 5.7 1 3090 5.2
3 System peak 6.8
4 Nitrite 7.4 1 3270 2.3
5 Bromide 8.6 1 3970 1.3
6 Nitrate 10.3 1 3600 1.9
7 Phosphate 11.6 1 3290 0.7
8 Sulfate 14.1 1 2980 1.1
78 Metrohm
Monograph
Chromatogram 17 Ultrapure water

1 Chloride 5.7 0.030 2240 0.17
2 System peak 6.8
Remarks
Thoroughly rinse all vessels, syringes and the system several times; use plastic vessels.

4.3 Experiments for determining anions
4.3.1 Experiment 8 – Determining anions in drinking water
Drinking water is our most important foodstuff. It is obtained mainly from ground water
and surface water. Surface waters include water from lakes and reservoirs, bank filtrate,
groundwater enriched with surface water and river water.
According to DIN 2000 drinking water must satisfy the following requirements:
It should be colorless, clear, cool and free from foreign odor and taste.
If possible it should be naturally free from pathogens and substances which are hazardous to
health.
It should not contain too many salts, particularly hardness components, iron, manganese, as well as
organic substances (peat and humic substances).
It should not cause corrosion.
The amount available should be sufficient to supply all the requirements of the population supplied with it.
Depending on the degree of pollution various methods are used for the treatment of drinking water.
Screening, removes coarse soil and larger particles.

Sand filter, for filtration; biodegradation processes also occur in the sand and help with purification.
Active charcoal filter adsorbs dissolved organic substances, e.g. pesticides.
Removal of iron and manganese by the oxidation of Fe(II) and Mn(II); this process would otherwise take
place in the drinking water pipeline and result in brown turbidity or flocs in the drinking water.
Figure 28 Drinking water treatment – diagram by Thomas Seilnacht, Tuttling
80 Metrohm
Monograph
Disinfection is always necessary when the water is not pathogen-free. Chlorine, ozone,
chlorine dioxide and UV irradiation are all used.
Preventative chlorination before release into the drinking water pipeline in order to
prevent growth of microorganisms on the way to the consumer.
Learning content
• Investigation of the «Number 1» foodstuff
• Checking the information given on bottles of mineral water
Table 28 Limiting values for drinking water (Federal Republic of Germany)
Fluoride 1.5 mg/L as F–

Nitrate 50 mg/L as NO3–
Nitrite 0.1 mg/L as NO2–
Chloride 250 mg/L
Sulfate 250 mg/L

Sample Drinking water
Method exp_08_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation

Chromatogram 18 Drinking water from Herisau (Switzerland)
Table 30 Components – Standard

1 Fluoride 3.7 0.05 2680 1.2
2 Chloride 5.8 6.5 2500 104
3 System peak 6.8
4 Nitrate 10.3 8.4 4560 74
5 Sulfate 14.4 14.4 3670 68
82 Metrohm
Monograph
Chromatogram 19 Mineral water without carbon dioxide
Table 31 Components – Mineral water without carbon dioxide

1 Fluoride 3.7 1.5 2560 35
2 Chloride 5.7 14.1 2980 226
3 System peak 6.8
4 Bromide 8.5 0.075 4810 0.5
5 Nitrate 10.3 1.4 4400 12
6 Sulfate 14.3 300 3830 3400
Remarks
Mineral water containing carbon dioxide must be degassed before the measurement – why?

4.3.2 Experiment 9 – Anions in ethanol and spirits (liquor)
The determination of anions in organic solvents is possible, although at the start of the chromatogram
pronounced system peaks often occur. Analyses of gin, whiskey and ethanol are used as examples.
In order to obtain lower detection limits, the preconcentration technique can be applied (see chapter
4.2.8). In some cases, however, the matrix (e.g. ethanol) may greatly interfere with the
determination, leading to badly shaped peaks that cannot be evaluated (see chromatogram 25). It is
then necessary to remove the matrix by rinsing the preconcentration column with ultrapure water
(matrix elimination). In this way good chromatograms are obtained (see chromatogram 24).
The matrix elimination technique can be used to analyze polar and even non-polar solvents.
An alternative method to remove organic matter from aqueous solutions is to use a RP
(Reversed Phase) sample preparation column.
Learning content
• Analysis of foodstuffs
• Influence of the matrix on chromatography
• Sample preparation
• Sample preconcentration and matrix elimination
Table 32 Parameters – Experiments 9a to 9c

Sample a) Gin
b) Whiskey
c) Ethanol
Method exp_09_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 5 MPa
b) 33 min
c) 17 min
Loop a) 100 µL
b) 100 µL
c) 500 µL on 6.1006.300 Metrosep Anion preconcentration column;
for matrix elimination rinse with 2 mL ultrapure water
Autostep with Fill
Polarity +
84 Metrohm
Monograph
Eluent preparation
Experiment 9a – Determination of anions in gin
Chromatogram 20 Standard solution for the analysis of gin
Table 33 Components – Experiment 9a – Standard

1 Chloride 5.5 0.1 4240 7.8
2 System peak 7.0
3 Nitrate 9.6 0.02 2980 0.9
4 Sulfate 13.0 0.4 3320 22
5 Oxalate 14.9 0.02 3710 0.7

Chromatogram 21 Analysis of gin
Table 34 Components – Experiment 9a – Gin

1 Chloride 5.6 0.11 2230 8.8
2 Nitrate 9.7 0.014 3360 0.6
3 Sulfate 13.0 0.43 3260 23.5
4 Oxalate 14.9 0.013 3920 0.5
86 Metrohm
Monograph
Experiment 9b – Determination of anions in whiskey
Chromatogram 22 Standard solution for the analysis of whiskey
Table 35 Components – Experiment 9b – Standard

1 Chloride 5.5 1 4700 84
2 System peak 7.0
3 Nitrate 9.6 0.5 3640 20
4 Phosphate 10.8 0.5 2960 11
5 Malate 12.1 0.5 3730 306
6 Sulfate 13.0 1 3350 56
7 Oxalate 14.9 1 3250 41

Chromatogram 23 Analysis of whiskey
Table 36 Components – Experiment 9b – Whiskey

1 Chloride 5.6 1.3 3300 167
2 System peak 7.3
5 Nitrate 9.8 0.22 4000 8.7
6 Phosphate 10.9 0.43 3510 9.6
7 Malate 12.4 0.81 4580 5.8
8 Sulfate 13.1 0.88 3040 49
9 Oxalate 15.1 1.91 3540 79
Remarks
Peaks 3, 4 and 10 not evaluated.
88 Metrohm
Monograph
Experiment 9c – Determination of anions in ethanol with preconcentration
and matrix elimination
Chromatogram 24 Determination of anions in ethanol with matrix elimination
Table 37 Components – Experiment 9c – with matrix elimination

1 Chloride 5.3 0.021 3570 9.5
2 System peak 6.8
3 Nitrate 9.3 0.013 3940 2.8
4 Sulfate 12.3 0.046 2130 14
5 Oxalate 14.1 0.018 3250 3.8

Chromatogram 25 Determination of anions in ethanol without matrix elimination
Table 38 Components – Experiment 9c – without matrix elimination

No peaks
Remarks
Thoroughly rinse all vessels, syringes and the system several times; use plastic vessels.
90 Metrohm
Monograph
4.3.3 Experiment 10 – Anions in lettuce
Nitrate enters the human body via drinking water, but also by eating vegetables, salad, etc.
The WHO (World Health Organization) recommends that the daily nitrate consumption should
not exceed 220 mg per person. In Germany the average daily consumption is about 130 mg
per person per day. Approx. 5% of this originates from meat and sausages; the remainder is
split about 50:50 between drinking water and veg-etables, salad, etc.
Nitrate can have an adverse effect on human health in several different ways. Nitrate itself is relatively
non-toxic. Only when larger amounts are consumed can this lead to inflammation of the gastro-intestinal
tract. However, under certain conditions, particularly in the presence of bacteria such as are present in the
human mouth, nitrate is reduced to nitrite by the enzyme nitrate reductase:
Nitrite is able to convert hemoglobin, the red blood colorant, to methemoglobin (Fe 2+ is oxidized to Fe3+). In
contrast to hemoglobin, methemoglobin cannot transport oxygen in the blood. In adult human beings this
damage can be remedied by metabolic reactions. However, the metabolism of babies up to 5 months old
is not yet able to do this. This results in a lack of oxygen in the baby's blood and the skin turns bluish. This
cyanosis or methemoglobinemia can sometimes result in death.
In the acidic surroundings of the stomach nitrite can react with various secondary
amines (two H atoms of the ammonium molecule are replaced by alkyl residues), which
enter the human body via medicines and foodstuffs, to form nitrosamines.
Nitrosamines are among the most carcinogenic substances known. They are formed
within the organism from non-carcinogenic compounds.
Learning content
• Checking foodstuffs for nitrite and nitrate in particular


Sample Lettuce
Method exp_10_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 5 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
Sample preparation
Chop up lettuce, disperse, add ultrapure water (ratio 1:100) and filter.
92 Metrohm
Monograph
Chromatogram 26 Standard solution for the analysis of lettuce
Table 40 Components – Experiment 10 – Standard solution

1 Chloride 5.3 5 4480 80
2 System peak 6.7
3 Nitrate 9.3 5 4320 42
4 Phosphate 10.4 5 2990 24
5 Malate 11.8 10 3140 26
6 Sulfate 12.7 2 3330 22
7 Oxalate 14.6 0.1 3500 0.9

Chromatogram 27 Analysis of lettuce (1:100 dilution)
Table 41 Components – Experiment 10 – Lettuce

1 Chloride 5.3 540 4260 86
2 System peak 6.6
4 Nitrate 9.4 410 4240 34
5 Phosphate 10.4 540 2960 25
6 Malate 11.8 1160 2180 30
7 Sulfate 12.6 206 2800 23
8 Oxalate 14.5 10 2300 1
Remarks
94 Metrohm
Monograph
4.3.4 Experiment 11 – Phosphoric acid in cola drinks
Coca-Cola is a non-alcoholic beverage which contains carbon dioxide and caffeine. It was first
made in 1885 by the American pharmacist Pemberton. Among its ingredients are extracts of
cola nuts, bitter oranges, locust beans, ginger essence, 12% sugar, 0.28% phosphoric acid
(pH 2.7), caramel color and carbon dioxide. The caffeine content is 16 mg/100 mL.
The determination of the phosphoric acid content in the cola drinks is of special
significance as the local cola bottlers get the concentrate and the bottling is controlled
via the phosphate content, requiring a highly accurate determination.
Many cola drinks are available on the market (Pepsi Cola, Club Cola, River Cola, Afri
Cola, etc.); the composition of these may differ from Coca-Cola.
Phosphoric acid is a tribasic acid (pK A1= 2.161; pKA2= 7.207; pKA3= 12.325). The amounts of
the different species vary with the pH as can be seen in the following diagram:
Figure 29 Buffering effect of phosphoric acid in the pH range 6 ... 8
A mixture of primary and secondary phosphate is frequently used as a buffer solution which
buffers in the pH range 6 ... 8 (90% H2PO4– + 10% HPO42– to 10% H2PO4– + 90% HPO42–).
See also the Henderson-Hasselbalch equation (buffer equation)

Learning content
• Phosphoric acid chemistry
• Influence of the pH on chromatographic separation
• Statistics: reproducibility

Sample Coca-Cola
Method exp_11_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Analysis time 18 min for Coca-Cola, 30 min for low-calorie Coca-Cola
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
96 Metrohm
Monograph
Chromatogram 28 Standard solution for the analysis of cola

1 Chloride 5.3 1 4140 15
2 System peak 6.7
3 Nitrate 9.4 1 4220 8.0
4 Phosphate 10.5 50 3250 261
5 Sulfate 12.7 1 2950 13

Experiment 11a – Analysis of cola (1:10 dilution)
Chromatogram 29 Analysis of cola (1:10 dilution)

1 Chloride 5.3 5.9 3100 8.9
2 System peak 6.8
3 Nitrate 9.5 5.9 5000 4.7
4 Phosphate 10.5 510 3370 266
5 Sulfate 12.8 11.0 3520 14
98 Metrohm
Monograph
Experiment 11b – Analysis of low-calorie cola (1:10 dilution)
Chromatogram 30 Analysis of low-calorie cola (1:10 dilution)

1 Chloride 5.3 6.0 2990 9.2
2 System peak 6.7
3 Nitrate 9.4 7.3 4290 5.8
4 Phosphate 10.5 663 1850 346
5 Sulfate 12.8 14.4 1630 19
Remarks

Experiment 11c – Reproducibility of the phosphate measurements in cola
Chromatogram 31 Merger of 8 measurements (undiluted)
Table 46 Reproducibility of the measurements
Chromatogram Phosphate peak area Phosphate conc.

[µS/cm*s] [mg/L]
1 3627 519
2 3629 520
3 3626 519
4 3626 519
5 3636 521
6 3638 521
7 3639 521
8 3638 521
Standard deviation: below 0.2%
Remarks
The cola must be degassed. In low-calorie cola the sweetener cyclamate lies under the phosphate peak.
100 Metrohm
Monograph
4.3.5 Experiment 12 – Organic acids in wine
According to the German wine law, wine is a product which is only obtained by the
complete or partial alcoholic fermentation of fresh or mashed grapes or from grape juice.
Grape juice contains about 12 … 25% carbohydrates (glucose, fructose) and 0.9 …
1.5% acids; the most important are L-(+) tartaric acid (2R, 3R) and malic acid, but citric
acid, ketoglutaric acid, succinic acid and lactic acid may also be present.
An important criterion for assessing the grape juice is the Oechsle degree (Oe°); the higher it is the more
sugar the juice contains. It indicates the number of grams by which 1 L juice at 20 °C is heavier than 1 L
distilled water. For example, juice with a density of 1.115 kg/L (115 g more than 1 L water) has 115
°Oechsle. From the degrees Oechsle a simple calculation permits determination of the sugar and alcohol
content. 1.7 g sugar produce 1 mL (0.794 g) ethanol. At an alcohol volume fraction of 12 … 15% fermen-
tation comes to a standstill as the yeasts are killed off by the alcohol they have produced.
The aroma of the wine is made up of 600 to 800 components: hydrocarbons, alcohols,
aldehydes, ke-tones, acids, esters, lactones, ethers, phenols and many more.
Of analytical interest are the 2R, 3R-tartaric acid, malic acid, citric acid, lactic acid and
succinic acid. The total acid content (calculated as tartaric acid) is usually between 5.5
and 8.5 g/L. Acetic acid, propionic acid, higher fatty acids and abnormal amounts of
lactic acid occur in "spoiled" wine and are chiefly pro-duced by microorganisms.
L-(+)-tartaric acid
(2R, 3R)-form
Alcoholic fermentation takes place according to the following equation:
Figure 30 Abbreviations: ADP = adenosine diphosphate, ATP = adenosine triphosphate, P = phosphate
The weak organic acids are determined by ion exclusion chromatography (see chapters
3.3.4, 3.6.7 and 3.7.2.3).

Table 47 Acid content (mg/L) of German wines (mean value from 4 or 2 individual analyses, German denominations have been retained)
10
Typical Riesling Müller-Thurgau

high-quality
wine Portugieser Kabinett Spätlese Auslese Beerenaus- Silvaner Spätlese Auslese Beeren-
Rotwein lese, Eiswein Kabinett auslese
Oxalic acid 15.7 13.0 11.0 45.8 16.0 21.7 16.7 40.9 15.4 19.5
Succinic acid 194.0 260.1 205.8 282.1 230.2 149.2 243.8 215.1 264.9 269.2
Fumaric acid 44.2 31.9 24.6 28.3 20.8 36.0 20.9 51.8 27.0 40.6
Glutaric acid 3.7 1.9 4.5 2.6 2.3 7.0 2.6 2.2 1.9 6.2
c- or t- Aconitic acid 2.1 1.9 + 5.5 4.9 6.4 1.4 2.5 1.6 4.5
Glycolic acid 1.8 1.3 + + 1.4 6.9 3.7 3.4 1.7 5.8
D- + L-Lactic acid 1789 2364 319.8 159.8 151.0 2141 793 221.0 208.1 2096
Anglyceric acid 43.5 62.6 50.1 39.5 59.0 53.0 49.6 87.0 68.8 49.9
Triglyceric acid ± ± ± ± ± ± ± ± ± ±
3-M-2,3-DHBS ± ± ± ± ± ± ± ± ± ±
Malic acid 3971 5080 3850 3871 4235 2251 2893 3163 3410 2897
Tartaric acid 1586 994 1428 1431 817 1251 1280 1014 805 887
Citramalic acid 94.5 53.7 63.0 18.6 46.8 48.2 31.3 33.8 24.2 41.0
α-Hydroxyglutaric acid 24.9 27.5 18.2 24.5 28.4 20.6 18.8 15.3 26.9 22.2
Citric acid 138.9 150.2 241.1 222.8 298.6 287.3 200.7 221.7 240.2 335.1
Glyoxylic acid + 1.0 + + 4.0 6.1 2.9 1.8 1.1 3.1
Pyruvic acid 20.6 29.8 17.8 12.4 16.8 8.6 17.6 22.7 18.6 33.0
α-Ketoglutaric acid 41.1 45.7 38.6 36.8 55.7 35.6 41.0 33.7 40.3 27.5
Gluconic acid 59.0 357.2 54.5 95.9 452.1 337.2 53.9 131.1 373.9 540
Mucic acid – + – – 4.1 20.4 – + 4.5 11.2
Glucuronic acid 2.1 3.4 3.8 5.8 7.9 14.5 1.7 6.0 7.6 10.2
Galacturonic acid 11.1 11.7 14.1 19.7 22.0 43.4 10.0 17.3 23.2 34.3
L-Ascorbic acid 12.9 9.0 13.7 10.1 9.8 9.6 12.0 10.4 9.7 8.5
Total acids 7977 9491 6349 6302 6474 6744 5685 5284 5565 7333
Metrohm
Remarks
– = not detectable ± = present in traces (approx. 5 mg/L), not evaluated
+ = traces 3-M-2,3-DHBS = 3-methyl-2,3-dihydroxybutyric acid
Learning content
• Ion exclusion chromatography
• Which ions can be determined by ion exclusion chromatography?
Column 6.1005.200 Metrosep Organic Acids (7.8 x 250 mm)

Eluent 0.5 mmol/L H2SO4 / acetone (85:15)
Sample Wine
Method exp_12_o.mtw
System orgacids.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 20 µL
Polarity +
Eluent preparation
Mix together 0.5 mmol H2SO4 (850 mL) and acetone (150 mL).
Sample preparation
Dilute sample 1:100, filter wine through 0.45 µm filter.

Experiment 12a – Determination of organic acids in white wine
Chromatogram 32 Standard for the determination of organic acids in wine
Table 49 Components – Experiment 12a – Standard solution

1 Citrate 7.2 5 26200 1.1
2 Tartrate 7.5 20 7990 31
3 Malate 8.3 5 9210 4.5
4 Succinate 9.9 5 7140 1.2
5 Lactate 10.8 20 8830 11
6 Acetate 13.1 10 11500 1.2
7 System peak 15.9
104 Metrohm
Monograph
Chromatogram 33 Determination of organic acids in white wine (1:100 dilution)
Table 50 Components – Experiment 12a – White wine

1 Citrate 7.2
2 Tartrate 7.5 1210 8430 19
4 Malate 8.2
7 Succinate 9.8 350 5660 0.8
8 Lactate 10.7 2190 8820 13
9 Acetate 13.0 710 5200 0.8
10 System peak 15.8
Remarks
Peaks 3, 5, 6 not evaluated.

Experiment 12b – Determination of organic acids in red wine
Chromatogram 34 Determination of organic acids in red wine (1:100 dilution)
Table 51 Components – Experiment 12b – Red wine

1 Citrate 7.2
2 Tartrate 7.5 2230 8300 34
4 Malate 8.2
7 Succinate 9.9 410 10500 1.0
8 Lactate 10.8 1560 9570 8.9
9 Acetate 13.1 1010 7950 1.1
10 System peak 15.9
Remarks
Peaks 3, 5, 6 were not identified; citrate and malate could not be quantified correctly.
106 Metrohm
Monograph
4.3.6 Experiment 13 – Determination of contaminants in borate – chloride and
sulfate in borax solutions
Borax (disodium tetraborate, Na2B4O7·10 H2O, Na2[B4O5(OH)4]·8H2O) has the following structure:
Figure 31 «Borax» (disodium tetraborate, Na2B4O7·10 H2O,

Na2[B4O5(OH)4]·8H2O)
When it melts borax can dissolve many metal oxides with the formation of characteristic colors. These
«borax pearls» are well-known in practical inorganic chemistry. Borax is also used in the manufacture of
glass, pottery glazes, porcelain and as a flux in brazing. At 100 °C borax loses 5 water molecules and
becomes the pentahydrate «jeweler's borax». If a soldering flux is added to it then surface contaminants –
mainly oxide layers – are destroyed. These would otherwise affect the formation of an alloy between the
solder (itself an alloy of silver, copper and tin) and the basic material.
Sodium tetraborate (borax) solutions are used in the internal cooling circuit of nuclear power
plants as neutron absorbers. The purity of the material is extremely important as traces of
chloride and sulfate cause corrosion in the piping, which must be avoided by all means.
Boric acid H3BO3 or B(OH)3 is a very weak monobasic acid whose pK A value of 9.25
corresponds approxi-mately to that of HCN. Boric acid is not an H+ donor (Brönsted acid
definition), but rather an OH– acceptor (Lewis acid definition).
Ion chromatography without chemical suppression uses an acidic eluent with pH = 4.1 for the
determina-tion of the contaminants in borate. At this pH borate is present almost entirely as boric
acid B(OH)3. In contrast to the negatively charged anions, boric acid does not interact with the
stationary phase of the separating column. This means that it elutes in the dead volume.
However, with chemical suppression the weakly alkaline carbonate/hydrogen carbonate
eluent is used instead. Although it is now possible to separate borate as an anion, the
detection does not function. The cause of this can be found in the suppressor, which
exchanges all the Na+ ions by H+ ions. As a result, the weak boric acid is formed.
The large amount of boric acid disturbs the chromatogram, making the determination of the anions
almost impossible. Matrix elimination (see chapter 4.3.2) is the best possibility to solve the problem.
In power plants, traces of anions must often be determined in water samples containing
2 to 4% boric acid. In these cases, the matrix elimination technique with sample
preconcentration is applied (see chromatogram 37).
Learning content
• Strong and weak acids
• Comparison between measurements with electronic and chemical suppression

Experiment 13a – Measurement without chemical suppression (with electronic suppression)

Eluent 8 mmol/L phthalic acid, 2% acetonitrile; pH = 4.1 (TRIS)
Sample 1 g/L Borax in ultrapure water, spiked with 1 ppm chloride and 1 ppm sulfate
Method exp_13_n.mtw
System anonsupp.smt
Flow 0.5 mL/min
Pressure 2 MPa
Loop 100 µL
Polarity +
Eluent preparation
Dissolve 1.33 g phthalic acid in 20 mL acetonitrile and a little water, add the solution to degassed
water and make up to 1 L. Adjust the pH to 4.1 by the addition of solid TRIS (approx. 1 g).
Chromatogram 35 Borate spiked with 1 ppm chloride and 1 ppm sulfate – without chemical suppression
108 Metrohm
Monograph

1 Chloride 4.4 1 2790 12
2 Sulfate 9.0 1 3270 8.4
3 System peak 19
Experiment 13b – Measurement with chemical suppression

Sample 1 g/L Borax spiked with 1 ppm chloride, sulfate
Method exp_13_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 2 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation

Chromatogram 36 Borate spiked with 1 ppm chloride and 1 ppm sulfate – with chemical
suppression Table 55 Components – Experiment 13b

1 Chloride 5.4 1 4170 15
2 Sulfate 13.7 1 3290 11
Example chromatogram – Determination of trace anions in boric acid with

preconcentration and matrix elimination
Table 56 Parameters – Example chromatogram
Column 6.1006.100 Metrosep Anion Dual 2 (4.6 x 75 mm)

Eluent 0.8 mmol/L NaHCO3 / 5.5 mmol/L Na2CO3
Sample 4% aqueous solution of boric acid
Flow 0.8 mL/min
Pressure 4.6 MPa
Sample introduction 2 mL sample is passed over a preconcentration column where the trace
anions to be determined are retained. Afterwards the preconcentration column
is rinsed with ultrapure water in order to remove the boric acid (matrix elimina-
tion) and then switched into the eluent path (Inject). The retained trace anions are
re-eluted, transported to the Metrosep Anion Dual 2 column and separated there.
Autostep with Fill
Polarity +
110 Metrohm
Monograph
Eluent preparation
carbonate in 1 L ultrapure water.
Chromatogram 37 Determination of trace anions in 4% boric acid with preconcentration and matrix elimination
Table 57 Components – Example chromatogram
Peak Component tR [min] Conc. [µg/L]

1 Chloride 5.7 15.6
3 Nitrate 12.6 4.1
4 Phosphate 15.6 15.5
5 Sulfate 20.9 35.8

4.3.7 Experiment 14 - Determination of anions in wastewater
In biological treatment plants wastewater is mainly purified with the help of bacteria.
Organic substances are oxidized to a large extent with the consumption of oxygen.
Apart from the oxidation of organic substances, ammonium can also be oxidized to
nitrate (nitrification) in suitably designed plants.
In oxygen-free basins bacteria utilize the nitrate oxygen for the oxidation of organic
substances (denitrifica-tion).
Phosphate – a plant nutrient like NH4+ and NO3– – can be precipitated, e.g. by the addition of
Fe3+ salt solutions. Apart from the so-called sum parameters – biochemical oxygen demand
(BOD), chemical oxygen demand (COD), total organic carbon (TOC) – which are a measure
of the organic load of the wastewater or water in general, the analysis of NH 4+, NO3–, PO43– is
also important. Cl–, SO42– are normally only analyzed under special circumstances.
In communal treatment plants with more than 100 000 so-called population equivalents (1 population
equivalent is the sewage flow per head) the following limits have been laid down in Germany:
BOD 15 mg/L
COD 75 mg/L
NH4-N 10 mg/L*
NTot 18 mg/L* (sum of NH4-N, NO2-N, NO3-N)
PO4-PTot 1 mg/L
* Only applies at a wastewater temperature ∞ 12 °C, as nitrification is greatly influenced by the temperature.
NH4-N, NO2-N, NO3-N means that all the values of the nitrogen contained in the ions is
taken into consid-eration; the same applies for PO4-P (P content).
Learning content
• Environmental analysis
• Sample preparation techniques
• Analysis of mixtures of substances with large differences in concentration – dynamic
concentration range
112 Metrohm
Monograph
Table 58 Parameters – Experiment 14a and 14b

Sample Herisau wastewater
Method exp_14_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 2 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
Sample preparation
Filtering of the samples is absolutely essential. Use, for example, Minisart (Sartorius) or
one-way filter holders (Schleicher & Schüll) with a pore size of 0.45 µm or less. Even
seemingly clear solutions can contain very fine particles that damage the column.

Experiment 14a - Treatment plant inflow
Chromatogram 38 Standard chromatogram for the analysis of a treatment plant inflow
Table 59 Components – Experiment 14a – Standard

1 Chloride 5.2 100 3470 2270
2 Nitrate 9.1 2 4330 16
3 Phosphate 10.3 5 3040 21
4 Sulfate 12.5 100 3820 1470
114 Metrohm
Monograph
Chromatogram 39 Analysis of a treatment plant inflow
Table 60 Components – Experiment 14a – Treatment plant inflow

1 Chloride 5.2 128 2980 2910
5 Nitrate 9.2 2.1 4620 16
6 Phosphate 10.3 7.0 3040 30
7 Sulfate 12.5 132 3720 1940
Remarks
Peaks 2, 3, 4 and 8 not evaluated.

Experiment 14b - Treatment plant outflow
Chromatogram 40 Standard chromatogram for the analysis of a treatment plant outflow

1 Fluoride 3.6 0.1 2900 2.1
2 Chloride 5.2 5 4140 78
3 Nitrate 9.1 10 4210 87
4 Sulfate 12.5 5 3420 53
116 Metrohm
Monograph
Chromatogram 41 Analysis of a treatment plant outflow
Table 62 Components – Experiment 14b – Treatment plant outflow

1 Fluoride 3.6 0.05 2900 1.1
2 Chloride 5.2 7.3 3870 114
4 Nitrate 9.2 8.5 4390 73
5 Sulfate 12.5 6.8 3460 71
Remarks
Peak 3 not evaluated.

4.3.8 Experiment 15 – Fluoride in toothpaste
Toothpastes are made from different ingredients:
• Water – 30 to 40%
• Cleaning substances – are insoluble, inorganic substances which intensify the cleaning
action of the toothbrush. They have a particle size <15 µm. Commonly used cleaning
substances are Al2O3, CaCO3, CaHPO4·2H2O, SiO2·H2O, sodium aluminum silicate.
• Fluoride – increases the resistance of the dental enamel against attack by acids originating from
bacterial plaque. Fluorides also make the mineralization of the dental enamel possible (the
inorganic part of dental enamel consists mainly of calcium phosphate, hydroxyapatite, calcium
carbonate, mag-nesium phosphate, calcium fluoride and calcium chloride). This means that
fluoride is important for the prevention of caries. The fluorine compounds most frequently used
are sodium fluoride, sodium monofluorophosphate and quaternary ammonium fluorides, which
also contain free fluoride ions. Fluo-ride is added to the drinking water in some countries.
Sodium monofluorophosphate
• Surfactants (e.g. sodium lauryl sulfate) – lower the surface tension and help to distribute
the tooth-paste evenly. They increase the cleaning effects, particularly in locations which
are difficult to reach with the toothbrush. Other ingredients of toothpastes are e.g.:
• Moisteners (e.g. glycerol, sorbite, polyethylene glycol) – improve the low-temperature
stability and prevent drying out.
• Binders and thickeners (e.g. sodium carboxymethylcellulose) – prevent separation
into liquid and solid phases.
• Sweeteners (e.g. sodium saccharin) – improve the taste of the toothpaste.
• Preservatives (e.g. 4-hydroxybenzoic acid) – are used to protect the toothpaste
against bacterial decomposition.
• Aromatic substances – are added to increase both the acceptance of the toothpaste
and also hygiene consciousness. These include peppermint oil, menthol, aniseed oil,
eucalyptus oil, aromatic oils, citrus oil.
Analysis of toothpaste by ion chromatography determines the fluoride originating from
sodium fluoride together with the sodium monofluorophosphate.
Remarks
Citrate elutes from the Metrosep Anion Dual 1 (3 x 150 mm) only after approx. 90 min.
In order to check whether citrate is present in the toothpaste, Experiment 15b uses the Metrosep Anion
Dual 1 precolumn cartridge (6.1006.030) instead of the Metrosep Anion Dual 1 separating column.
118 Metrohm
Monograph
Learning content
• Quality control
Experiment 15a – Toothpaste (1) without citrate


Sample Standard (fluoride, chloride, phosphate, sulfate, saccharin)
Toothpaste
Method exp_15_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 3 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
Sample preparation
Dissolve 1 g toothpaste in 19 mL ultrapure water and then filter it through a 0.45 µm filter.

Chromatogram 42 Toothpaste (1) without citrate (1:20 dilution)

1 Fluoride 3.9 1304 1357 1663
2 Formate 4.5 52 1643 19.8
3 Chloride 5.6 66 4325 55.3
4 System peak 6.7
5 Monofluorophosphate 10.2 4527 3.1
6 Phosphate 11.5 260 3047 55.4
7 Sulfate 14.1 1346 3831 880
8 Saccharin 42.6 160 1917 179
Experiment 15b – Toothpaste (2) with citrate
Column 6.1006.030 Metrosep Anion Dual 1 precolumn cartridge

Sample Toothpaste
Method exp_15b_s.mtw
System asupp.smt
Flow 0.5 mL/min
120 Metrohm
Monograph
Pressure 3 MPa
Loop 20 µL
Autostep with Fill
Polarity +
Eluent preparation
Sample preparation
Dissolve1 g toothpaste in ultrapure water (1:20 dilution) and then filter it through a 0.45 µm filter.
Chromatogram 43 Toothpaste (2) with citrate (1:20 dilution)

1 Saccharin 8.2 160 510 177
2 Citrate 16.2 2600 267 360

4.3.9 Experiment 16 – Anions in brown and white sugar
Sugars are organic compounds with a semiacetal-forming carbonyl group and several
hydroxyl groups. In general use ‘sugar’ normally refers to the disaccharide saccharose.
Figure 32 The disaccharide saccharose
In the manufacture of sugar from sugar beet the beet are first washed and chopped up; they are
then extracted with water in so-called diffusion units in counterflow. The soluble constituents –
sugar, salts, acids, proteins, pectins – are dissolved. The major share of the non-sugar constituents
is precipitated out by the addition of burnt lime (CaO). Carbon dioxide (CO 2) is then used to
precipitate the excess calcium hydroxide as CaCO 3. After filtration the sugar solution is
concentrated in multi-stage evaporators to form «thick juice», filtered again and concentrated further
until the sugar separates out as «white massecuite». The sugar is separated off in centrifuges and,
after purification (recrystallization), snow-white crystal sugar with a purity of 99.95% is obtained. The
centrifuge run-off of the last stage is a brown-colored syrup – molasses.
Brown sugar is less intensively purified and may be colored by the addition of molasses.
Apart from organic contaminants, it contains alkali metal and alkaline earth ions as well
as anions; it also has a different taste to white crystal sugar.
The organic contaminants can be separated off with an RP column before the anions
are determined. Learning content
• Process control
• Checking foodstuffs containing large amounts of sugar, e.g. honey
122 Metrohm
Monograph

Sample a) White sugar
b) Brown sugar
Method exp_16_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 4 MPa
Loop 100 µL
Autostep with Fill
Polarity +
Eluent preparation
Sample preparation
Dissolve the sugar in ultrapure water (1:10 dilution) and filter through a 0.45 µm filter.

Experiment 16a – White sugar
Chromatogram 44 Standard solution for the analysis of white sugar
Table 68 Components – Experiment 16a – Standard solution

1 Chloride 5.5 0.1 4408 8.1
2 System peak 7.0
3 Nitrate 9.6 0.1 3682 4.0
4 Malate 12.0 0.1 3587 1.2
5 Sulfate 12.9 0.1 2995 5.9
6 Oxalate 14.8 0.1 3260 3.7
124 Metrohm
Monograph
Chromatogram 45 Analysis of white sugar (1:10 dilution)
Table 69 Components – Experiment 16a – White sugar

1 Chloride 5.5 1.3 4183 10.3
2 System peak 7.2
3 Nitrate 9.8 0.8 4157 3.2
4 Malate 12.2 1.5 2833 1.8
5 Sulfate 13.1 0.9 3404 5.2
6 Oxalate 15.0 1.4 3432 5.3

Experiment 16b – Brown sugar
Chromatogram 46 Standard solution for the analysis of brown sugar
Table 70 Components – Experiment 16b – Standard solution

1 Chloride 5.3 20 3640 2200
2 System peak 6.9
3 Nitrate 9.6 0.1 3700 3.9
4 Phosphate 10.7 10 3330 245
5 Malate 12.1 5 3430 62
6 Sulfate 13.0 5 3600 294
7 Oxalate 14.9 1 3220 40
126 Metrohm
Monograph
Chromatogram 47 Analysis of brown sugar (1:10 dilution)
Table 71 Components – Experiment 16b – Brown sugar

1 Chloride 5.4 217 3480 2380
2 System peak 7.2
3 Nitrate 9.7 1.8 2870 7.0
4 Phosphate 10.8 84 3320 205
5 Malate 12.2 55 3840 68
6 Sulfate 13.0 74 3980 435
7 Oxalate 14.9 6.9 3530 28
Remarks
With brown sugar, contaminants may elute at later retention times; this could interfere
with the following chromatograms if the run time is too short. This is why the white sugar
should be measured first, followed by the brown sugar.

4.3.10 Experiment 17 – Contaminants in hydrogen peroxide
Pure hydrogen peroxide (H2O2) melts at 0.4 °C and boils at 150 °C. Pure hydrogen peroxide can
only be prepared by fractional crystallization under strict safety conditions. Commercial H 2O2 is
available as an aqueous solution with concentrations of 35, 50, 60 or 70%. These solutions are
purified by means of ion exchangers or by distillation. The strongly exothermal decomposition of
H2O2 into H2O and O2 does not occur spontaneously, but heavy metals act as catalysts.
2 H2O2 → 2 H2O + O2 +196.2 kJ

Heavy metal ions are bound by the addition of stabilizers such as polyphosphates, EDTA,
stannate etc. This inhibits decomposition. The characteristic property of H 2O2 is its oxidizing
effect. The standard poten-tial (E0) is + 1.8 V at pH = 0 and + 0,78 V at pH = 14.
Hydrogen peroxide is one of the most important products in the basic chemicals sector with a yearly production of
2.7 million tonnes. It is manufactured industrially by the conversion of anthrahydroquinone with atmospheric O 2.
This produces the corresponding anthraquinone and H 2O2. Anthraquinone is reduced back to anthrahydroquinone
by elemental hydrogen and a palladium catalyst and is returned to the system.
A large proportion of the H2O2 is used for bleaching paper and cellulose. In many
countries chlorine bleaches (with Cl2 or ClO2), with which not readily biodegradable
chlorinated organic compounds enter the wastewater, have been wholly or partially
replaced by other methods. This means that H2O2 has become very important.
Other fields of application are:
Removing iron and manganese from drinking water.
Detoxifying wastewater containing cyanides (CN– → CNO–), e.g. wastewater from
electroplating baths, with H2O2 or H2O2/H2SO4.
The combination of H2O2 and UV supplies HO radicals (hydroxyl radicals), which are extremely strong
oxidants (E0 = + 2,8 V). These are of interest for the purification of special types of wastewater.
The development of a method for the manufacture of propylene oxide from propene and H 2O2
(titanium layer catalysts) instead of the water-polluting chlorohydrin method is very promising.
Among the secondary products of H2O2, sodium perborate and sodium percarbonate are
the most impor-tant ones; these are used as bleaches in washing powders.
H2O2 is used in the electronics industry for the cleaning of silicon wafers and printed circuits.
The determination of contaminants in H2O 2 is of great importance, above all in the last-mentioned
electron-ics industry. Even the smallest amounts of foreign ions (ng/L or ppt) significantly decrease the
yield of wafers as, for example, phosphate and nitrate cause n-lattice defects in the silicon crystal.
At elevated concentrations, hydrogen peroxide affects both the separation column and the carbonate equi-
librium of the eluent (see chromatogram 49). This is why matrix elimination (see chapter 4.3.2) is applied in
trace analysis with the following advantages: First, the concentrated solutions can be analyzed without
dilution; second, larger sample volumes can be used (preconcentration).
128 Metrohm
Monograph
Learning content
• Process control
• Selectivity of different columns

Sample Hydrogen peroxide 30%, suprapur
Method exp_17_s.mtw
System asupp.smt
Flow 0.5 mL/min
Pressure 2 MPa
Sample introduction 1 mL sample on preconcentration column; for matrix elimination, rinse
with 1 mL ultrapure water
Autostep with Fill
Polarity +
Eluent preparation
Sample introduction
Rinse the system thoroughly with ultrapure water, then pass 1 mL sample over the
preconcentration column and rinse with 1 mL ultrapure water.

Chromatogram 48 Standard solution for the determination of anions in hydrogen peroxide

1 Acetate 4.2 5 2620 108
2 Formate 4.4 1 2940 222
3 Chloride 5.3 1 3300 587
4 System peak 6.9
5 Nitrate 9.2 0.1 3730 31
5 Sulfate 12.4 0.5 3160 163
6 Oxalate 14.2 0.1 3010 21
130 Metrohm
Monograph
Experiment 17a – Analysis of hydrogen peroxide without matrix elimination
Chromatogram 49 Analysis of hydrogen peroxide (30%) without matrix elimination

Experiment 17b – Analysis of hydrogen peroxide with matrix elimination
Chromatogram 50 Analysis of hydrogen peroxide (30%) with matrix elimination

2 Acetate 4.2 8.8 1780
3 Formate 4.4 0.83 2170
5 Chloride 5.3 0.86 2960 507
6 System peak 7.2
7 Nitrate 9.3 0.15 4560 47
8 Sulfate 12.5 0.44 2520 142
10 Oxalate 14.1 0.05 2480 10
Remarks
Rinse vessels, syringes and system thoroughly several times. Use plastic vessels.
Protective goggles must be worn! Peaks 1, 4 and 9 not evaluated.
132 Metrohm
Monograph
Experiment 17c – Analysis of hydrogen peroxide with matrix elimination on a
high-perfor-mance column
Table 75 Parameters – Experiment 17c
Column 6.1006.530 Metrosep A Supp 5 (4 x 250 mm)

Eluent 1 mmol/L NaHCO3 / 3.2 mmol/L Na2CO3
Sample Hydrogen peroxide 30%, suprapur
Method exp_17c_s.mtw
System asupp5.smt
Flow 1.0 mL/min
Pressure 11 MPa
Sample introduction 1 mL sample on preconcentration column; for matrix elimination rinse
with 1 mL ultrapure water
Autostep with Fill
Polarity +
Eluent preparation
Dissolve 339 mg sodium carbonate (anhydrous) and 84 mg sodium hydrogen carbonate
in 1 L ultrapure water.
Sample introduction
Rinse the system thoroughly with ultrapure water, then pass 1 mL sample over the
preconcentration column and rinse with 1 mL ultrapure water.

Chromatogram 51 Analysis of hydrogen peroxide (30%) with matrix elimination on the Metrosep A Supp 5

3 Acetate 6.3 6.8 2850 219
4 Formate 6.7 0.77 8740 123
6 Chloride 8.9 0.78 17810 380
7 System peak 13.0
8 Nitrate 16.4 0.15 19100 37
10 Sulfate 23.3 0.35 16640 86
13 Oxalate 27.0 0.04 12100 7.7
Remarks
Peaks 1, 2, 5. 9, 10, 11 and 12 not evaluated.
134 Metrohm
Monograph
4.4 Experiments for determining cations
4.4.1 Experiment 18 – Alkali metals and alkaline earth metals in drinking
water and mineral water
Apart from the dissolved gases O 2, N2 and CO 2, natural water also contains salts which are mainly
leached out of the soil and rocks to enter the ground water. Another ingredient of natural water are polar
organic compounds originating, for example, from the humus layers of the soil. Contamination by
wastewater is also a possible source of various salts and organic compounds. The most important salts
are the chlo-rides, sulfates and hydrogen carbonates of sodium, calcium and magnesium.
An important parameter of drinking water, both for its use as a foodstuff and its use in
washing processes or industrial processes, is the so-called water hardness.
The total hardness of the water is understood as being the sum of the molar concentrations
(mmol/L) of the calcium and magnesium ions. That part of the hardness which can be removed by
boiling is known as the carbonate hardness (previously temporary hardness). The residual
hardness is caused by sulfate and chloride ions, whose Ca and Mg salts cannot be precipitated out
by boiling.
With the classical soaps – sodium salts of fatty acids – calcium and magnesium ions form insoluble
calcium and magnesium compounds. These are both ineffective in washing and are also deposited
on textiles as a «gray frosting». Modern washing agents contain alkyl sulfates which do not form
insoluble calcium and magnesium compounds. The zeolites which are also added to these washing
agents function as ion exchangers and bind Ca2+ and Mg2+ ions. This effectively prevents the
precipitation of insoluble CaCO3 and basic magnesium carbonate on heating.
The drinking water regulations, which are the implementation of an EC drinking water directive (80/778/
EEC), contain the following values for cations:
NH4+ 0.5 mg/L

Na+ 150 mg/L
K+ 12 mg/L
Mg2+ 50 mg/L
Ca2+ 400 mg/L
An increased intake of sodium ions by human beings causes high blood pressure, among other things.
The daily Na+ requirement of 1 g is greatly exceeded today (3 to 7 g).
In all analyses carried out the samples must be acidified by the addition of nitric acid (pH
2.5 to 3.5), as otherwise no reproducible results will be obtained for divalent cations.
If the sodium content of the sample ist substantially higher than that of the standard
solution, the latter’s sodium content should be adapted to that of the sample.
Learning content
• Checking the «Number 1» foodstuff
• Checking the information given on bottles of mineral water
• Why is it necessary to acidify the samples?


Eluent 4 mmol/L tartaric acid / 0.75 mmol/L dipicolinic acid
Sample Standard (sodium, ammonium, potassium, calcium, magnesium +
2 mmol/L HNO3)
– Tap water (+ approx. 100 µL 2 mol/L HNO3 for 100 mL sample)
to pH = 2.5 ... 3.5)
– Mineral water (+ approx. 100 µL 2 mol/L HNO3 for 100 mL sample)
to pH = 2.5 ... 3.5)
Method exp_18_c.mtw
System cation.smt
Flow 1 mL/min
Pressure 7 MPa
Loop 10 µL
Polarity –
Eluent preparation
under heating and make up to 1 L with ultrapure water.
136 Metrohm
Monograph
Table 78 Components – Experiment 18 – Standard

1 Sodium 3.8 0.5 4200 1.5
2 Potassium 6.5 0.2 3090 0.9
3 Calcium 8.4 20 1960 66
4 Magnesium 11.0 5 2700 34
Chromatogram 53 Tap water (Herisau, Switzerland; 1:10 dilution)
Table 79 Components – Experiment 18 – Tap water

1 Sodium 3.8 5 4840 1.4
2 Calcium 8.7 85 2640 29
3 Magnesium 11.2 19 3520 13

Chromatogram 54 Mineral water (1:10 dilution)
Table 80 Components – Experiment 18 – Mineral water

1 Sodium 3.7 4.3 4190 1.3
2 Potassium 6.4 0.8 6350 0.3
3 Calcium 8.3 344 1520 113
4 Magnesium 10.9 62 2550 43
Remarks
All solutions must be stored in plastic vessels. All contact with glass must be avoided for a correct sodium
determination. The pH value of the standard and sample solutions should be between 2.5 and 3.5.
138 Metrohm
Monograph
4.4.2 Experiment 19 – Determination of transition metals
Complexing agents are added to the mobile phase in order to separate the transition metal ions. They
reduce the charge density and improve the selectivity of the separation, which is relatively low for transi-
tion metal ions having the same charge. Apart from the equilibrium between exchanger resin and analyte
ion, if complexing agents are added there is a further equilibrium, namely between metal ion and
complexing agent. This equilibrium is also influenced by the pH of the solution if various dissociation steps
of the complexing agent are possible or if the metal ions form hydroxy complexes.
Weak organic acids are often used as complexing agents, e.g. tartaric acid, citric acid, oxalic acid, pyri-
dine-2,6-dicarboxylic acid (dipicolinic acid – see chapter 4.2.7 – Experiment 6 – Altering the selectivity by
using complexing agents). The number of ligands L surrounding the central metal ion (Me) can vary, e.g.
MeL, MeL2, MeL 3. The resulting charge can also differ. Depending on the charge of the metal ion, the
ligands and their number, either cationic, neutral or anionic complexes can be present. This means that,
depending on their charge, the complexes can be separated on cation exchangers or anion exchangers.
Theoretically the use of exchangers containing both cation and anion exchanger groups is possible.
The separation can be influenced and optimized by varying the pH value and the complexing
agents – two or more different complexing agents can be added to the mobile phase. In part
the influences are contrary and difficult to predict. Some general information is given below:
• Different stabilities (complex formation constants) influence the separation.
• The addition of an organic solvent, e.g. acetone, to the eluent also influences the
separation. Lipophilic ions elute more quickly after the addition.
• In cation exchange chromatography, ethylenediamine has proven itself as an eluting
agent. Under normal conditions it is present as a cation carrying two protons.
• An increase of the pH results in a reduction of the retention time by reducing the total charge.
• An increase in the ligand concentration in the mobile phase, apart from displacing the
complexing equilibrium, also increases the concentration of the counter-ion H+ or Na+
and accelerates the dis-placement of the complex from the negatively charged
exchange sites, i.e. the separation performance is reduced.
• An increase in the ligand concentration causes an increase in the retention time as the coordination
number of the complex increases, but the free anionic ligands also promote the elution of the anionic
metal complex, so that two opposing effects exist with regard to the retention time.
Detection of the complexes can be carried out either by conductivity or photometrically
(post-column derivatization).
For conductivity detection only detection without chemical suppression can be used as
insoluble hydrox-ides would be formed by the suppressor reaction and the only eluent
anions available are carbonate or hydroxide.
Photometric detection requires post-column derivatization in which an additional, chromophoric
complexing agent displaces the one originally present (e.g. tartaric acid, oxalic acid...). The newly
formed and UV- or VIS-absorbing complex is detected, whereby the absorption maximum of the
free ligands must not be in the region of the maximum of the complex. As, for most complexing
dyestuffs, the maxima of the indi-vidual transition-metal complexes lie in different wave-length
regions, the detection limits of the individual metals differ greatly.

Learning content
• Influence of the eluent on the selectivity
• Complexing of transition metal ions
• Complexing agents for photometric detection
• Photometry
Column 6.1007.000 Nucleosil 5SA (4 x 125 mm)

Eluent a) 4 mmol/L tartaric acid, 0.5 mmol/L citric acid,
3 mmol/L ethylenediamine, 5% acetone
b) 3.5 mmol/L oxalic acid
5% acetone
pH = 4 (approx. 120 µL ethylenediamine)
Sample Standard
Tap water
Method exp_19_c.mtw
System nucleosil.smt
Flow 1.5 mL/min
Pressure 13 MPa
b) 13 min
Loop 100 µL
Polarity –
140 Metrohm
Monograph
Experiment 19a – Determining transition metals with an eluent containing tartaric
acid, citric acid, ethylenediamine and acetone
Eluent preparation
Dissolve 600 mg tartaric acid and 105 mg citric acid in ultrapure water. Add 200 µL
ethylenediamine and 50 mL acetone and make up to 1 L.
Chromatogram 55 Standard solution 1 for determining the transition metals (Eluent a)

Table 82 Components – Experiment 19a – Standard solution 1

1 Nickel 3.4 5 1020 40
2 Zinc 4.4 5 5640 36
3 Cobalt 5.6 5 4370 34
4 Iron(II) 8.1 10 6150 30
5 Calcium 9.8 5 6340 29
6 Magnesium 10.8 5 6390 39

Chromatogram 56 Standard solution 2 for determining the transition metals (Eluent a)
Table 83 Components – Experiment 19a – Standard solution 2

1 Lead 2.9 5 2680 8.6
2 Nickel 3.4 5 930 43
3 Zinc 4.3 5 5510 37
4 Cobalt 5.6 5 4310 34
5 Cadmium 8.6 5 6600 15
6 Manganese 9.9 10 6270 45
142 Metrohm
Monograph
Chromatogram 57 Analysis of tap water (Eluent a – 1:10 dilution)
Table 84 Components – Experiment 19a – Tap water

1 Zinc 4.2 0.12 6360 0.9
2 Calcium 9.8 9.0 5750 53
3 Magnesium 10.6 1.9 7460 17

Experiment 19b – Determining transition metals with an eluent containing oxalic
acid, ethyl-enediamine, acetone
Eluent preparation
Dissolve 315 mg oxalic acid in ultrapure water, add 50 mL acetone and make up to 1 L
with ultrapure water. Adjust to pH = 4 with ethylenediamine (approx. 120 µL).
Chromatogram 58 Standard solution for determining the transition metals (Eluent b)

1 Iron 2.2 10 2110 50
2 Manganese 4.0 10 1830 110
3 Magnesium 7.5 5 3110 98
4 Calcium 12.3 5 6000 45
144 Metrohm
Monograph
Chromatogram 59 Analysis of tap water (Eluent b, 1:10 dilution)
Table 86 Components – Experiment 19b – Tap water

1 Magnesium 7.3 41 4690 2.1
2 Calcium 12.4 83 4780 9.1
Remarks
Calcium and manganese coelute if Eluent a is used. With Eluent b calcium and manganese
are separated; nickel, zinc and cobalt are strongly complexed and elute in the water peak.

4.4.3 Experiment 20 - Contaminants in silica gel - determination of calcium and
magne-sium ions
Silica gel is produced, for example, by the hydrolysis of sodium silicate and the almost
complete removal of water; it has the following structure:
Apart from its use as a technical adsorption agent, silica gel is used in both gas
chromatography and high pressure liquid chromatography.
In gas chromatography originally only packed columns were used – they still are used
to a small extent today. A liquid phase, e.g. silicone oil, is applied to a particulate carrier
such as silica gel. The number of theoretical plates of such columns is low compared
with those of the capillary columns which are mainly used today.
In high pressure liquid chromatography (HPLC) silica gel is used as a stationary phase or carrier material for
adsorption, reversed phase (RP), normal phase and ion chromatography. For some of these applica-tions the
silica gel surfaces have to be modified with functional groups (e.g. C18 or ion exchanger groups).
In adsorption chromatography silica gel is also used as a stationary phase or in addition to
Al2O3. The chromatographic separation is based on dipole-induced dipole linkage, dipole-
dipole linkage, hydrogen bridge linkage and π-complex linkage. Adsorption chromatography is
used for the separation of non-polar substances which are difficult to dissolve in water.
In RP chromatography the free silanol groups of the silica gel are hydrophobicized by
the chemical bond-ing of longer alkyl chains (e.g. octyl or octadecyl groups):
Figure 33 Reaction of silica gel with

chlorosilan (R = C8H17 to C18H37)
In this conversion free residual silanol groups remain; these can adsorb polar compounds and cause peak
tailing. These residual silanol groups can be deactivated by trimethylchlorosilane – «end capping».
In normal phase chromatography the polar residues are chemically bonded to the silanol groups, e.g.:
A less polar or nonpolar mobile phase is used with this polar stationary phase for chromatographic sepa-
ration. In RP chromatography, which is used in approx. 75% of all HPLC applications, the polarities are
reversed and a nonpolar stationary phase is used with a polar mobile phase. This means that the name
reversed phase has a historical basis as this method was only developed later.
146 Metrohm
Monograph
In ion chromatography silica gel to which sulfonic acid groups have been bonded is
used as a cation exchanger for the analysis of alkali ions.
Contamination of silica gel by metal ions is important in chromatography as these can cause non-
specific interactions or blank values. A strongly acidic cation exchanger is used for the analysis of
these contami-nants; monovalent cations elute in the dead volume and only the divalent cations are
separated. Fe(III) must be reduced by ascorbic acid to Fe(II) before the analysis.
Learning content
• Quality control
• Additional experiment: spiking the extract with Fe(III); determination with and without
the addition of ascorbic acid (vitamin C)
• HPLC separating columns based on silica gel
Column 6.1007.000 Nucleosil 5SA (4 x 125 mm)

Eluent 4 mmol/L tartaric acid, 0.5 mmol/L citric acid,
3 mmol/L ethylenediamine, 5% acetone
Sample Silica gel (5% solution)
Method exp_20_c.mtw
System nucleosil.smt
Flow 1.5 mL/min
Pressure 13 MPa
Loop 100 µL
Polarity –
Eluent preparation
Dissolve 600 mg tartaric acid and 105 mg citric acid in ultrapure water. Add 200 µL
ethylenediamine and 50 mL acetone and make up to 1 L with ultrapure water.

Chromatogram 60 Standard solution for the determination of cations in silica gel

1 Calcium 9.6 0.5 6990 3.1
2 Magnesium 10.5 0.1 7260 0.7
148 Metrohm
Monograph
Chromatogram 61 Determination of cations in silica gel
Table 89 Components – Experiment 20 – Silica gel

Iron 8.1 n.d. – –
1 Calcium 9.7 9.4 6850 2.9
2 Magnesium 10.6 1.4 10100 0.4

4.4.4 Experiment 21 – Cosmetics and corrosion protection: determination of
ethanolamine and alkali metals
The following three ethanolamines, whose systematic names are aminoethanol,
iminodiethanol and nitrilotriethanol, are made by reacting ammonia and ethylene oxide.
Aminoethanol Iminodiethanol
Nitrilotriethanol
All three substances are used for removing CO2 and H2S from mixtures of gases, e.g. for
removing carbon dioxide from synthesizer gas and in the synthesis of ammonia as well
as for the removal of hydrogen sulfide from refinery gases.
At a higher temperature CO2 is again released and the ethanolamine NR3 is returned to
the absorption process.
The H2S released again at the higher temperature is oxidized to liquid sulfur in «Claus
units»; this is converted to sulfuric acid via SO2 and SO3.
Monoethanolamine (MAK = maximum allowable workplace concentration = 3 ppm) is
used in surfac-tants as a fatty acid ester. Diethanolamine is used in furniture and floor
care products, shoe polish and lubricants.
Triethanolamine forms triethanolamine soaps with fatty acids, e.g. with stearic acid
C18H35COOH. These are easily soluble in water and mineral oils and are therefore used
as emulsifiers. They may also be contained in cosmetic preparations (e.g. shaving
foam).
Monoethanolamine is used as corrosion inhibitor in power stations as it maintains a
weakly alkaline pH and scavenges excess H+ ions.
150 Metrohm
Monograph
For their determination by ion chromatography the ethanolamines are protonated by the
addition of acid and can then be determined as their ammonium derivatives.
Learning content
• Determining inorganic and organic cations
• Changing the selectivity by adding complexing agents
• Determination of amines by ion chromatography
Table 90 Parameters – Experiments 21a to 21c

Eluent a ) 4 mmol/L tartaric acid / 0.75 mmol/L dipicolinic acid
b) 4 mmol/L tartaric acid / 0.5 mmol/L dipicolinic acid
Sample Ethanolamine, triethanolamine + standard cations
Method exp_21_c.mtw
System cation.smt
Flow 1 mL/min
Pressure 6 MPa
b) 13 min
c) 14 min
Loop 10 µL
Polarity –
Eluent preparation
a) Dissolve 600 mg tartaric acid and 125 mg dipicolinic acid in 100 mL ultrapure water
under heating, then make up to 1 L with ultrapure water.
b) Dissolve 600 mg tartaric acid and 84 mg dipicolinic acid in 100 mL ultrapure water,
then make up to 1 L with ultrapure water.

Chromatogram 62 Standard 1 – Eluent a
Table 91 Components – Experiment 21a – Standard 1 (Eluent a)

1 Sodium 3.8 2 4520 6.8
2 Ammonium 4.3 2 4340 6.8
3 Monoethanol-amine 4.9 7 4120 10.8
4 Potassium 6.4 5 3070 7.9
5 Triethanolamine 9.0 20 2230 6.9
152 Metrohm
Monograph
Chromatogram 63 Standard 2 – Eluent a
Table 92 Components – Experiment 21 – Standard 2 (Eluent a)
Peak Component tR [min] Conc. No. of plates Area

[mg/L] [µS/cm*s]
1 Sodium 3.7 2 4500 7.2
2 Ammonium 4.3 2 4190 7.0
3 Monoethanolamine 4.9 7 4380 9.8
4 Potassium 6.4 5 2930 8.6
5 Calcium + triethanolamine 8.7 5 + 20 2070 24
6 Magnesium 11.0 5 2970 32

Chromatogram 64 Standard 2 – Eluent b
Table 93 Components – Experiment 21 – Standard 2

1 Sodium 3.9 2 4700 7.2
2 Ammonium 4.5 2 4110 7.0
3 Monoethanol-amine 5.1 7 4400 9.6
4 Potassium 6.6 5 2920 8.4
5 Triethanolamine 9.3 20 2400 7.3
6 Calcium 10.8 5 3240 16
7 Magnesium 12.2 5 2820 32
Remarks
If Eluent a is used then calcium and monoethanolamine coelute.
All solutions must be stored in plastic vessels. All contact with glass must be avoided for
a correct sodium determination.
154 Metrohm
Monograph
4.4.5 Experiment 22 – Alkali metals and alkaline earth metals in wine
The mineral substances in the grape juice are chiefly phosphates of calcium, magnesium and potassium.
The concentrations of these compounds are 3 – 5 g/L. The mineral content, also known as «ash» of the
wine is lower than that of the juice as a part of the minerals is taken up by the yeasts in their metabolism.
The mineral content is also reduced by the separation of tartrates. This means that wine contains only
about 1.8 – 2.5 g/L «ash». Important cationic constituents are given as oxides; these are K 2O (approx.
40%), MgO (approx. 6%), CaO (approx. 4%) and Na 2O (approx. 2%).
(see Experiment 12)
Learning content
• Process analysis – checking tartrate precipitation

Eluent 4 mmol/L tartaric acid / 0.75 mmol/L dipicolinic acid
Sample Standard (sodium, potassium, calcium, magnesium + 2 mmol/L HNO 3)
Red wine (Pinot Noir, Switzerland), White wine (Fechy, Switzerland)
Method exp_22_c.mtw
System cation.smt
Flow 1 mL/min
Pressure 6 MPa
Loop 10 µL
Polarity –
Eluent preparation:
under heating, then make up to 1 L with ultrapure water.
Sample preparation:
Filter and dilute the sample (1:10).

Chromatogram 65 Standard solution for determining cations in wine
Table 95 Components – Experiment 22 – Standard

1 Sodium 3.7 1 4360 3.5
2 Potassium 5.9 100 1480 180
3 Calcium 8.6 5 2950 16
4 Magnesium 10.8 10 2150 66
Remarks
All solutions must be stored in plastic vessels. All contact with glass must be avoided for a correct
sodium determination. The pH of the standard and sample solutions must be between 2.5 and 3.5.
156 Metrohm
Monograph
Chromatogram 66 Determination of cations in white wine (1:10 dilution)
Table 96 Components – Experiment 22 – White wine

1 Sodium 3.7 24 4220 8.4
5 Potassium 6.0 590 1860 106
6 Calcium 8.6 72 2920 23
8 Magnesium 11.0 59 2880 39
Remarks
Peaks No. 2, 3, 4 and 7 not evalued.

Chromatogram 67 Determination of cations in red wine (1:10 dilution)
Table 97 Components – Experiment 22 – Red wine

1 Sodium 3.7 10 2000 3.6
6 Potassium 5.8 1380 1300 248
8 Calcium 8.6 50 3030 16
10 Magnesium 10.8 80 2520 53
Remarks
Peaks No. 2, 3, 4, 5, 7 and 9 not evaluated.
158 Metrohm
Monograph
5 Literature cited
[1] H. Small, T.S. Stevens, W.C. Bauman, Anal. Chem. 47 (1975) 1801
[2] J. Weiß «Ionenchromatographie», 2. Aufl. (1991), Verlag Chemie, Weinheim
[3] J.M. Mermet, M. Otto, H.M. Widmer «Analytical Chemistry», 1st ed. (1998), Wiley-
VCH Verlag, Weinheim-New York
[4] P.R. Haddad, P.E. Jackson, «Ion Chromatography: Principles and Applications», 1 st
ed. (1990), J. Chromatogr. Library Vol. 46, Elsevier Verlag, Amsterdam
[5] J.S. Fritz, D.T. Gjerde, «Ion Chromatography», 3rd ed., Wiley-VCH, Weinheim, 2000
[6] G. Schwedt, «Chromatographische Methoden in der Anorganischen Analytik»,
1. Aufl. (1980), Dr. Alfred Hüthig Verlag, Heidelberg
[7] International Union of Pure and Applied Chemistry (IUPAC), Pure & Appl. Chem. 65 (1993), 819
[8] H. Engelhardt, L. Rohrschneider «Deutsche chromatograpische Grundbegriffe

zur IUPAC-Nomenklatur» (1998), Universität Saarbrücken
[9] G. Schwedt «Chromatographische Trennmethoden», 3. Aufl. (1994), Thieme Verlag, Stuttgart
[10] V.R. Meyer «Praxis der Hochleistungsflüssigchromatographie», 5. Aufl. 1988,

Diesterweg Verlag, Frankfurt/Main
[11] A.J.P Martin, R.L.M. Synge, Biochem. J. 35 (1941) 1358
[12] B.A. Bindlingmeyer, F.V. Warren, Anal. Chem. 56 (1984) 1583
[13] J.P. Foley, J.G. Dorsey, Anal. Chem. 55 (1983) 730
[14] E. Grushka, L.R. Snyder, J.H. Knox, J. Chrom. Sci. 13 (1975) 25
[15] E. Katz, K.L. Ogan, R.P.W. Scott, J. Chromatogr. A 270 (1983) 51
[16] J.J Van Deemter, F.J. Zuiderweg, A.J. Klinkenberg, Chem. Eng. Sci. 5 (1956) 271
[17] J.H. Knox, H.P. Scott, J. Chromatogr. A 282 (1983) 297
[18] A. Berthold, F. Chartier, J.L. Rocca, J. Chromatogr. A 469 (1989) 53
[19] G. Wedler «Lehrbuch der physikalischen Chemie», 3. Aufl. (1987), Verlag Chemie, Weinheim
[20] G. Schwedt, Fresenius Z. Anal. Chem. 320 (1985) 423

[21] M.J. van Os, J. Slania, C.L. de Ligny, W.E. Hammers, J. Agterdendos, Anal.
Chim. Acta 144 (1982) 73
[22] P.R. Haddad, C.E. Cowie, J. Chromatogr. A 303 (1984) 321
[23] A. Diop, A. Jardy, M. Caude, R. Roset, Analusis 14 (1986) 67
[24] A. Jardy, M. Caude, A. Diop, C. Curvale, R. Roset, J. Chromatogr. A 439 (1988) 137
[25] D.R. Jenke, G.K. Pagenkopf, Anal. Chem. 56 (1984) 85 und 88
[26] T.B. Hoover, Sep. Sci. Tech. 17 (1982) 295
[27] P.R. Haddad, P.E. Jackson, A.L. Heckenberg, J. Chromatogr. A 346 (1985) 139

[28] P. Janoš, J. Chromatogr. A 789 (1/2) (1997) 3
[29] P. Janoš, P. Aczel, J. Chromatogr. A 749 (1996) 115
[30] P. Kolla, J. Köhler, G. Schomburg, Chromatographia 23 465 (1987)
[31] C.A. Pohl, J. R. Stillian, P. E. Jackson, J. Chrom. A 789 29 (1997)
[32] K. Dorfner (Hrsg.), «Ion Exchangers», 4th ed. (1991), Walter de Gruyter Verlag, Berlin
[33] D.T. Gjerde, J.S. Fritz, G. Schmuckler, J. Chromatogr. A 186 (1979) 509
160 Metrohm
Monograph

ICPractical Ion Chromatography

Uploaded by

Copyright:

Available Formats

ICPractical Ion Chromatography

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ICPractical Ion Chromatography

Uploaded by

Copyright:

Available Formats

Practical Ion

Dipl.-Ing. Claudia Eith

All rights reserved to the publisher, including translation.

Practical Ion Chromatography 1

3.5.1 Electrochemical detection methods .......................................................................... 30

Practical Ion Chromatography 3

4.3.1 Experiment 8 - Determining anions in drinking water ............................................... 80

Kai Henning Viehweger

Practical Ion Chromatography 5

Practical Ion Chromatography 7

3.2 Theory of chromatography

A further differentiation of chromatography methods can be made according to the basic

Practical Ion Chromatography 9

As a result of diffusion processes, which increase in importance as the residence time on

Figure 3 Gaussian distribution with

Retention factor, selectivity and resolution

Practical Ion Chromatography 11

3.2.2 Theoretical concepts for describing the chromatography

The dynamic theory (van Deemter theory)

Practical Ion Chromatography 13

Figure 4 Representation of the individual

Figure 5 HPLC or IC unit setup with the most important components

Practical Ion Chromatography 15

3.3 Basic principles of ion chromatography (IC)

3.3.2 Ion exchange

Practical Ion Chromatography 17

Thermodynamic aspects of the ion exchange process

3.3.4 Ion exclusion

Practical Ion Chromatography 19

Figure 9 Dependency of the elution volume on

3.4.1 Retention models in anion chromatography

Retention model for eluents with one anion

According to the law of mass action this equilibrium can be described by a

Practical Ion Chromatography 21

This means that Equation 21 can be converted to:

This equation is of crucial importance for anion chromatography as it provides a

From Equation 25 it can be seen that:

Figure 10 Graphical presentation of Equation 28

Equation 27 has been confirmed in numerous publications; however, under the

Practical Ion Chromatography 23

By taking Equation 20 into account the selectivity α is first obtained

and then after converting the Equations 31 a and b,

Practical Ion Chromatography 25

3.4.2 Retention models in cation chromatography

Retention model for eluents with one cation

Figure 11 Ionic species of

Retention model for elution in the presence of complexing agents

Practical Ion Chromatography 27

In a similar manner to Equation 25 the logarithmic form of Equation 47 is obtained as:

Calculation of the acid dissociation

Practical Ion Chromatography 29

3.5 Ion chromatography detection systems

3.5.1 Electrochemical detection methods

The equivalent conductivity Λ of a solution can be determined as:

Figure 12 Construction of a conductivity measuring cell.

According to Kohlrausch's law, the conductivity of a dilute solution is proportional to the

where κ is the conductivity in S cm –1, Λ the limiting conductivity in S cm 2 (z mol)–1 and c

Practical Ion Chromatography 31

Figure 13 Changes in the eluate