Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
211 views

Physical Programming With Arduino!: Some Sample Projects !

This document provides an overview of several physical computing and circuit projects that can be done with an Arduino board, including: - Blinking an LED, light sensing, playing tones with a piezo speaker, controlling a servo motor, and interfacing with Processing. - It also discusses logic gates and provides a code example for a logic tester circuit using an Arduino.

Uploaded by

yusufmagician
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
211 views

Physical Programming With Arduino!: Some Sample Projects !

This document provides an overview of several physical computing and circuit projects that can be done with an Arduino board, including: - Blinking an LED, light sensing, playing tones with a piezo speaker, controlling a servo motor, and interfacing with Processing. - It also discusses logic gates and provides a code example for a logic tester circuit using an Arduino.

Uploaded by

yusufmagician
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 16

CTA - 2014!

Physical Programming Some sample projects…!

with Arduino!
Arduino Uno - Arduino Leonardo look-alike!

Arduino Uno and its cheap


The Board! cousin from Borderless
Electronics!
Mini - Breadboard!

❖  typical solderless
breadboard has side rails
for positive and ground…!
❖  mini breadboards are
without rails!
If you’re designing circuits, you may be…!

Fritzing!
http://fritzing.org/home/!
!
Used to create breadboard diagrams - free
and open source!
!
Based on Processing…!

Arduino IDE!
Language based on C/C++(Wiring)!
Based on Processing IDE!
!Processing: setup() and draw()!
!Arduino: setup() and loop()!
TONS of examples:!
•  http://arduino.cc/en/Tutorial/
HomePage !
•  https://learn.adafruit.com/!
!
Some Basics…!

Compile/Download!
Select Tools>Board>Leonardo!
!
Select File>Examples> whichever !
!
Select ‘Check’ for compile!
!
Select ‘Arrow’ to download to board!
!
!
Blink (Arduino’s Hello World)!

/*!
  Blink!
  Turns on an LED on for one second, then off for one second,
repeatedly.!
  This example code is in the public domain.!
 */!
 !
// Pin 13 has an LED connected on most Arduino boards and!
// already has a resistor built in. Otherwise put resistor in!
// give it a name:!
!
int led = 13;!
!
// the setup routine runs once when you press reset:!
void setup() {                !
  // initialize the digital pin as an output.!
  pinMode(led, OUTPUT);     !
}!
!
// the loop routine runs over and over again forever:!
void loop() {!
  digitalWrite(led, HIGH);   // turn the LED on!
  delay(1000);               // wait for a second!
  digitalWrite(led, LOW);    // turn the LED off!
  delay(1000);               // wait for a second!
}!
Light Sensing!
/*!
  Photoresistor !
  Turns on an LED on when light level is below threshold. Open
the serial monitor to see the light values Tools>Serial Monitor!
 !
 */!
 !
!
int led = 11;!
int lightPin = 0;!
!
// the setup routine runs once when you press reset:!
void setup() {                !
  // initialize the digital pin as an output.!
  Serial.begin(9600);!
pinMode(led, OUTPUT);     !
}!
!
// the loop routine runs over and over again forever:!
void loop() {!
  Serial.println(analogRead(lightPin));   // turn the LED on
(HIGH is the voltage level)!
  delay(100);               // wait for a second!
  if (analogRead(lightPin)>900){!
!digitalWrite(led, HIGH); }   // turn the LED off by !
// making the voltage HIGH!
                !
else{!
digitalWrite(led, LOW);!
}!
}!
!
Piezo Speaker!
/*!
  Melody!
 !
 Plays a melody !
 !
 circuit:!
 * 8-ohm speaker on digital pin 8!
!
 */!
 #include "pitches.h"!
!
// notes in the melody:!
int melody[] = {!
  NOTE_C4, NOTE_G3,NOTE_G3, NOTE_A3, NOTE_G3,0, NOTE_B3, NOTE_C4};!
!
// note durations: 4 = quarter note, 8 = eighth note, etc.:!
int noteDurations[] = {!
  4, 8, 8, 4,4,4,4,4 };!
!
void setup() {!
  // iterate over the notes of the melody:!
  for (int thisNote = 0; thisNote < 8; thisNote++) {!
!
    // to calculate the note duration, take one second !
    // divided by the note type.!
    //e.g. quarter note = 1000 / 4, eighth note = 1000/8, etc.!
    int noteDuration = 1000/noteDurations[thisNote];!
    tone(8, melody[thisNote],noteDuration);!
!
    // to distinguish the notes, set a minimum time between them.!
    // the note's duration + 30% seems to work well:!
    int pauseBetweenNotes = noteDuration * 1.30;!
    delay(pauseBetweenNotes);!
    // stop the tone playing:!
    noTone(8);!
  }!
}!
!
void loop() {!
  // no need to repeat the melody.!
}!
Servo Motor!
!
!
#include <Servo.h> !
 !
Servo myservo;  // create servo object to control a servo !
                // a maximum of eight servo objects can be !
! ! ! // created !
 !
int pos = 0;    // variable to store the servo position !
 !
void setup() !
{ !
  myservo.attach(9); // attaches the servo on pin 9 to the servo !
} !
 !
 !
void loop() !
{ !
  for(pos = 0; pos < 180; pos += 1)  // goes from 0 to 180 !
  {                                  // in steps of 1 degree !
    myservo.write(pos);              //go to position 'pos' !
    delay(15);                       // waits 15ms!
  } !
  for(pos = 180; pos>=1; pos-=1)     // goes from 180 to 0 !
  {                                !
    myservo.write(pos);              // go to position 'pos' !
    delay(15);                       // waits 15ms!
  } !
}!
Interface with Processing!
Download

Library for Processing v2.0: processing2-arduino.zip (Updated 6 Nov. 2013) 


(properties file here: processing2-arduino.txt)

Library for Processing v1.5: processing-arduino.zip (Updated 11 Nov. 2011) 


(properties file here: processing-arduino.txt)
Instructions
1. Unzip the library and copy the "arduino" folder into the "libraries" sub-folder of your Processing Sketchbook. (You can find
the location of your Sketchbook by opening the Processing Preferences. If you haven't made a "libraries" sub-folder, create
one.)
2. Run Arduino, open the Examples > Firmata > StandardFirmata sketch (or servoFirmata), and upload it to the Arduino board.
3. Configure Processing for serial: http://processing.org/reference/libraries/serial/
4. In Processing, open one of the examples that comes with with the Arduino library.
5. Edit the example code to select the serial port used by Arduino. Specifically, change the [0] in this line arduino = new Arduino(this,
Arduino.list()[0], 57600);
6. 
To find the correct item in the array, run this code in Processing: import processing.serial.*;
7. import cc.arduino.*;
8. println(Arduino.list());
The output window will enumerate your serial ports. Select the number corresponding to the serial port in your Arduino
environment found under Tools > Serial Port.
9. Run the servo example.
Some Circuits (not Arduino)!
to illustrate Logic Gates!
NOT Logic Gate!
AND Logic Gate!
OR Logic Gate!
Logic Tester with Arduino!
/*!
Logic Tester with RGB LED!
Turns on the green LED when a logic "1" (+5V) signal is detected. The!
red LED will turn on at logic "0" (0V) signal. Also, when powering!
up the Arduino the red LED is on.!
*/!
// RG pins wired to the Arduino microcontroller!
// give them names:!
int redled = 9;!
int grnled = 10;!
int probein = 8;!
int probeStatus = 0;!
// the setup routine runs once when you press reset:!
void setup() {!
// initialize the digital pins as outputs:!
pinMode(redled, OUTPUT);!
pinMode(grnled, OUTPUT);!
pinMode(probein, INPUT);!
// turn RGB outputs off:!
digitalWrite(redled, HIGH);!
digitalWrite(grnled, HIGH);!
}!
// the loop routine runs over and over again forever:!
void loop() {!
// read the status of the test probe value:!
probeStatus = digitalRead(probein);!
if (probeStatus == HIGH) { // check if the test probe value is HIGH!
digitalWrite(redled, HIGH); // turn the red LED off (HIGH is off)!
digitalWrite(grnled, LOW); // turn the green LED on (LOW is on)!
}!
else {!
digitalWrite(redled, LOW); // turn the red LED on!
digitalWrite(grnled, HIGH); // turn the green LED off!
}!

You might also like