HP DeskJet F2280

HP Deskjet F2200 All-in-One series
Windows Help
Downloaded from ManualsPrinter.com Manuals


Contents
1 HP Deskjet F2200 All-in-One series Help...............................................................................7
2 HP All-in-One overview
The HP All-in-One at a glance....................................................................................................9
Contents
Control panel buttons...............................................................................................................10
Status light overview.................................................................................................................12
Use the HP Photosmart software.............................................................................................13
3 Find more information............................................................................................................15
4 How do I?.................................................................................................................................17
5 Connection information
Supported connection types.....................................................................................................19
Use printer sharing...................................................................................................................19
6 Load originals and load paper

Load originals...........................................................................................................................21
Choose papers for printing and copying...................................................................................21
Recommended papers for printing and copying.................................................................22
Recommended papers for printing only..............................................................................23
Papers to avoid...................................................................................................................23
Load paper...............................................................................................................................24
Load full-size paper............................................................................................................24
Load 10 x 15 cm (4 x 6 inch) photo paper..........................................................................26
Load index cards................................................................................................................27
Load envelopes..................................................................................................................28
Load other types of paper...................................................................................................29
7 Print from your computer

Print from a software application..............................................................................................31
Make the HP All-in-One the default printer...............................................................................32
Change the print settings for the current job............................................................................32
Set the paper size...............................................................................................................32
Set the paper type for printing............................................................................................33
View the print resolution.....................................................................................................33
Change the print speed or quality.......................................................................................34
Change the page orientation..............................................................................................34
Scale the document size....................................................................................................35
Preview your print job.........................................................................................................35
Change the default print settings..............................................................................................36
Printing shortcuts......................................................................................................................36
Create printing shortcuts....................................................................................................36
Delete printing shortcuts.....................................................................................................37
Downloaded from ManualsPrinter.com Manuals 1

Perform special print jobs.........................................................................................................37
Print a borderless image.....................................................................................................38
Print a photo on photo paper..............................................................................................39
Print using Maximum dpi...................................................................................................40
Print on both sides of the page...........................................................................................41
Print a multiple-page document as a booklet.....................................................................42
Print multiple pages on a single sheet................................................................................45
Print a multiple-page document in reverse order................................................................46
Reverse an image for iron-on transfers..............................................................................47
Print on transparencies.......................................................................................................47
Contents
Print a group of addresses on labels or envelopes............................................................48

Print a poster......................................................................................................................49
Print a Web page................................................................................................................49
Stop a print job.........................................................................................................................50
Resume a print job...................................................................................................................51
8 Use the copy features

Make a copy.............................................................................................................................53
Set the copy paper type............................................................................................................53
Change copy speed..................................................................................................................54
Make multiple copies of the same original................................................................................55
Copy a two-page black-and-white document...........................................................................56
Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo.....................................................56
Stop copying.............................................................................................................................57
9 Use the scan features

Scan an original........................................................................................................................59
Edit a scanned preview image..................................................................................................61
Edit a scanned image...............................................................................................................61
Edit a scanned document.........................................................................................................61
Stop scanning...........................................................................................................................62
10 Maintain the HP All-in-One

Clean the HP All-in-One...........................................................................................................63
Clean the exterior...............................................................................................................63
Clean the glass...................................................................................................................63
Clean the lid backing..........................................................................................................64
Print a self-test report...............................................................................................................65
2
Contents
Work with print cartridges.........................................................................................................65

Handle the print cartridges.................................................................................................66
Check the estimated ink levels...........................................................................................67
Replace the print cartridges................................................................................................67
Use ink-backup mode.........................................................................................................71
Ink-backup mode output...............................................................................................71
Exit ink-backup mode...................................................................................................71
Use a photo print cartridge.................................................................................................71
Store the print cartridges....................................................................................................72
Print cartridge storage and handling.............................................................................72
Contents
Print cartridge protector................................................................................................72
Align the print cartridges.....................................................................................................73
Clean the print cartridges...................................................................................................74
Clean the print cartridge contacts.......................................................................................75
Clean the area around the ink nozzles...............................................................................77
Remove ink from your skin and clothing.............................................................................80
11 Shop for ink supplies.............................................................................................................81
12 Troubleshooting
View the Readme file................................................................................................................83
Hardware setup troubleshooting...............................................................................................83
The product will not turn on................................................................................................84
Software installation troubleshooting........................................................................................87
Uninstall and reinstall the software.....................................................................................90
Paper jams................................................................................................................................92
Information on paper..........................................................................................................93
Print cartridge troubleshooting..................................................................................................93
Information on print cartridges............................................................................................94
Resolving print cartridge problems.....................................................................................95
Resolving print cartridge error messages...........................................................................95
Print quality troubleshooting.....................................................................................................98
Wrong, inaccurate, or bleeding colors................................................................................99
Ink is not filling the text or graphics completely................................................................102
The printout has a horizontal band of distortion near the bottom of a borderless
print...................................................................................................................................103
Printouts have horizontal streaks or lines.........................................................................105
Printouts are faded or have dull colors.............................................................................106
Printouts seem blurry or fuzzy..........................................................................................108
Printouts are slanted or skewed.......................................................................................110
Ink streaks on the back of the paper................................................................................110
Print troubleshooting...............................................................................................................112
Envelopes print incorrectly...............................................................................................112
Borderless printing produces unexpected results.............................................................113
The product is not responding..........................................................................................113
The product prints meaningless characters......................................................................116
Nothing happens when I try to print..................................................................................117
The margins are not printing as expected........................................................................119
Text or graphics are cut off at the edge of the page.........................................................121
A blank page came out while printing...............................................................................122

Copy troubleshooting..............................................................................................................124
Nothing happens when I try to copy.................................................................................125
Parts of the original do not appear or are cut off..............................................................126
The printout is blank.........................................................................................................127
A borderless copy has white space around the edges.....................................................128
Scan troubleshooting..............................................................................................................129
Scan fails..........................................................................................................................129
Text is incorrect or missing...............................................................................................132
Errors......................................................................................................................................133
Flashing lights...................................................................................................................133
Contents
Product messages............................................................................................................135
Mechanism error.........................................................................................................136
Scan errors.................................................................................................................137
Unable to print............................................................................................................152
Product might not be correctly installed......................................................................157
Product was not found................................................................................................161
Product could not find available scan destinations.....................................................165
Error occurred while communicating with the product................................................168
File messages...................................................................................................................172
Supported file types for the HP All-in-One..................................................................173
General user messages...................................................................................................173
Cannot crop................................................................................................................173
Paper messages...............................................................................................................174
Out of paper................................................................................................................175
Power and connection messages.....................................................................................179
Communication test failed..........................................................................................180
Two-way communication lost......................................................................................181
Print cartridge messages..................................................................................................182
The print carriage is stalled........................................................................................185
Need alignment or alignment failed............................................................................189
Print cartridges missing or not detected.....................................................................191
Incompatible print cartridges......................................................................................195
Print cartridge problem...............................................................................................198
13 HP warranty and support

Warranty.................................................................................................................................205
Print cartridge warranty information........................................................................................205
Support process.....................................................................................................................205
Before you call HP customer support.....................................................................................206
HP support by phone..............................................................................................................206
Phone support period.......................................................................................................206
Placing a call....................................................................................................................207
After the phone support period.........................................................................................207
Additional warranty options....................................................................................................207
HP Quick Exchange Service (Japan).....................................................................................208
HP Korea customer support...................................................................................................208
Prepare the product for shipment...........................................................................................209
Pack the product.....................................................................................................................209
14 Technical information
Specifications.........................................................................................................................211
4
Contents
Notice to Windows 2000 users...............................................................................................212

Environmental product stewardship program.........................................................................212
Paper use.........................................................................................................................213
Plastics.............................................................................................................................213
Material safety data sheets...............................................................................................213
Recycling program............................................................................................................213
HP inkjet supplies recycling program...............................................................................213
Energy Star® notice.........................................................................................................213
Disposal of waste equipment by users in private households in the European
Union................................................................................................................................214
Contents
Regulatory notices..................................................................................................................214
FCC statement..................................................................................................................215
Notice to users in Korea...................................................................................................215
VCCI (Class B) compliance statement for users in Japan................................................216
Notice to users in Japan about the power cord................................................................216
Noise emission statement for Germany...........................................................................216
Toxic and hazardous substance table..............................................................................216
HP Deskjet F2200 All-in-One series declaration of conformity.........................................217
Index............................................................................................................................................219

Contents
6
1 HP Deskjet F2200 All-in-
One series Help
For information about the HP All-in-One, see:
• HP All-in-One overview
• Find more information
• How do I?
• Connection information
• Load originals and load paper
• Print from your computer

• Use the copy features
• Use the scan features
• Maintain the HP All-in-One
• Shop for ink supplies
• HP warranty and support
• Technical information
NOTE: If you are using the product with a Windows 2000 computer, some features
may not be available. For more information, see Notice to Windows 2000 users.
Help
Downloaded from ManualsPrinter.com Manuals HP Deskjet F2200 All-in-One series Help 7

Chapter 1
Help
8 HP Deskjet
Downloaded F2200 All-in-One seriesManuals
from ManualsPrinter.com Help
2 HP All-in-One overview
The HP Deskjet F2200 All-in-One series is a versatile device that enables easy-to-use
copying, scanning, and printing.
Copy
The HP All-in-One allows you to produce high-quality color and black-and-white copies
on a variety of paper types. You can enlarge or reduce the size of an original to fit a
specific paper size, adjust the copy quality, and make high-quality copies of photos.
Scan
Scanning is the process of converting text and pictures into an electronic format for your
computer. You can scan almost anything (photos, magazine articles, and text documents)
on the HP All-in-One.
Print from your computer
The HP All-in-One can be used with any software application that allows printing. You
can print a range of projects, such as borderless images, newsletters, greeting cards,
iron-on transfers, and posters.
This section contains the following topics:
• The HP All-in-One at a glance
• Control panel buttons
• Status light overview
• Use the HP Photosmart software
The HP All-in-One at a glance
HP All-in-One overview
Label Description
1 Control panel
2 Input tray
Downloaded from ManualsPrinter.com Manuals HP All-in-One overview 9

Chapter 2
(continued)
Label Description
3 Tray extender
4 Paper-width guide
5 Print cartridge door
6 Glass
7 Lid backing
8 Rear access door
9 Rear USB port
10 Power connection*
* Use only with the power adapter supplied by HP.
Control panel buttons

Label Icon Name and Description
1 On: Turns the HP All-in-One on or off. The On button is lit when the HP All-
in-One is powered on. The light blinks while performing a job.
When the HP All-in-One is off, a minimal amount of power is still used by the
device. To completely disconnect the power supply to the HP All-in-One, turn
the device off, and then unplug the power cord.
CAUTION: Before you unplug the power cord, you must press the On
button and allow the HP All-in-One to turn itself off. This prevents the print
cartridges from drying out.
2 Check Print Cartridge lights: Indicates the need to reinsert the specified print
cartridge, replace the print cartridge, or close the print cartridge door. The
Black/Photo light indicates that the problem is with the black or photo print
10 HP All-in-One
Downloaded overview
from ManualsPrinter.com Manuals
(continued)
Label Icon Name and Description
cartridge, and the Color light indicates that the problem is with the tri-color
print cartridge.
3 Cancel: Stops a print, copy, or scan job.

A blinking Paper light next to the Cancel button indicates the need to load
paper or clear a paper jam. Press any button after a problem is solved to
instruct the HP All-in-One to continue.
4 Scan: Starts scanning the original currently on the glass. The Scan command
is ignored if the HP All-in-One is busy with any other job. The Scan command
functions only when the computer is on.
5 Paper Type: Changes the paper type setting to either plain or photo paper.
Make sure the appropriate paper type is loaded in the input tray. The default
paper type setting is Plain Paper.
The Paper Type lights indicate the currently selected paper size and type:
• Plain Paper: Letter and A4 paper
• Photo Paper (Large): Letter and A4 photo paper
• Photo Paper (Small): 10 x 15 cm (4 x 6 inch) photo paper
6 Start Copy Black: Starts a black-and-white copy job.

Press this button multiple times to specify multiple black copies. The printer
will start printing shortly after the number of copies have been selected. The
number of copies to be printed is shown to the right of this button.
TIP: The maximum number of copies you can make using the control panel
is 9 (varies by model). To make more copies at once, use the HP Software.
When initiating multiple copies of an original from the software, only the last
digit of the number of copies is represented on the control panel. For
example, if you are making 25 copies, the number 5 appears on the display.
7 Start Copy Color: Starts a color copy job.

Press this button multiple times to specify multiple color copies. The printer
will start printing shortly after the number of copies have been selected. The
number of copies to be printed is shown to the right of this button.
TIP: The maximum number of copies you can make using the control panel
is 9 (varies by model). To make more copies at once, use the HP Software.
When initiating multiple copies of an original from the software, only the last
digit of the number of copies is represented on the control panel. For
example, if you are making 25 copies, the number 5 appears on the display.
Downloaded from ManualsPrinter.com Manuals Control panel buttons 11

Chapter 2
Status light overview

Several indicator lights inform you of the status of the HP All-in-One.
Label Description
1 On light
2 Check Print Cartridge lights
3 Paper light
4 Paper Type lights (for the Paper Type button)
The following table describes common situations and explains what the lights mean.
Light status What it means

All lights are off. The HP All-in-One is turned off. Press the On button to turn on the device.
The On light and one of the Paper The HP All-in-One is ready for printing, scanning, or copying.
Type lights are on.
The On light is blinking. The HP All-in-One is busy printing, scanning, copying, or aligning the
print cartridges.
The On light blinks quickly for 3 You pressed a button while the HP All-in-One is already busy printing,
seconds and then is on steady. scanning, copying, or aligning the print cartridges.
The On light blinks for 20 seconds You pressed the Scan button and there was no response from the
and then is steady. computer.
The Paper light is blinking. • The HP All-in-One is out of paper.

• The HP All-in-One has a paper jam.
• The paper size setting in the copy software does not match the paper
size detected in the input tray.
The Check Print Cartridge light is • The print cartridge door is open.
blinking. • The print cartridges are missing or not seated correctly.
• The tape was not removed from the print cartridge.
12 HP All-in-One
Downloaded overview
(continued)
Light status What it means
• The print cartridge is not intended for use in this HP All-in-One.

• The print cartridge might be defective.
• The print cartridge is low on ink.
The On, Paper, and Check Print Scanner failure. For more information, see Scan fails.
Cartridge lights are blinking.
Turn off the HP All-in-One, then turn it on again. If the problem persists,
contact HP Support.
NOTE: HP All-in-One will still operate as a printer.
All lights are blinking. The HP All-in-One has a fatal error.

1. Turn the HP All-in-One off.
2. Unplug the power cord.
3. Wait a minute, then plug the power cord back in.
4. Turn the HP All-in-One back on.
If the problem persists, contact HP Support.
Use the HP Photosmart software

The HP Photosmart Software provides a fast and easy way to make prints of your photos.
It also provides access to other basic HP imaging software features, such as saving and
viewing your photos.
For more information on using the HP Photosmart Software:
• Check the Contents panel on the left. Look for the HP Photosmart Software Help
contents book at the top.
• If you do not see the HP Photosmart Software Help contents book at the top of the
Contents panel, access the software help through the HP Solution Center.
NOTE: The HP Photosmart software supports the following file formats: BMP, DCX,
FPX, GIF, JPG, PCD, PCX, TIF, PICT, PSD, PCS, EPS, TGA, SGI, PDF, and PNG
Downloaded from ManualsPrinter.com Manuals Use the HP Photosmart software 13

Chapter 2
14 HP All-in-One
Downloaded overview
3 Find more information
You can access a variety of resources, both printed and onscreen, that provide
information about setting up and using the HP All-in-One.
Setup Guide
The Setup Guide provides instructions for setting up the HP All-in-One and
installing software. Make sure you follow the steps in the Setup Guide in order.
If you have problems during setup, check the Setup Guide for troubleshooting
information, or see Troubleshooting in this onscreen Help.
Basics Guide
The Basics Guide contains an overview of the HP All-in-One, including step-
by-step instructions for basic tasks, troubleshooting tips, and technical
information.
HP Photosmart animations
The HP Photosmart animations, located in the relevant sections of the onscreen
Help, show you how to complete key tasks on the HP All-in-One. You will learn
how to load paper and other media, replace the print cartridges, and scan
originals.
Onscreen Help
The onscreen Help provides detailed instructions on using all features of the
HP All-in-One.
• The How Do I? topic provides links so you can quickly find information on
performing common tasks.
• The The HP All-in-One overview topic provides general information about
the main features of the HP All-in-One.
• The Troubleshooting topic provides information about resolving errors
you might encounter with the HP All-in-One.
Readme
The Readme file contains the most recent information which might not be found
in other publications.
Install the software to access the Readme file. For more information, see View
the Readme file.
www.hp.com/support If you have Internet access, you can get help and support from the HP Web
site. This Web site offers technical support, drivers, supplies, and ordering
information.
Find more information
Downloaded from ManualsPrinter.com Manuals Find more information 15

Chapter 3
Find more information
16 Find more
Downloaded frominformation
ManualsPrinter.com Manuals
4 How do I?
This section contains links to commonly performed tasks, such as printing photos and
optimizing your print jobs.
• How do I change the print settings?
• How do I print borderless photos on 10 x 15 cm (4 x 6 inch) paper?
• How do I load envelopes?
How do I?
• How do I scan using the control panel?
• How do I get the best print quality?
• How do I print on both sides of the paper?
• How do I replace the print cartridges?
• How do I align the print cartridges?
• How do I clear a paper jam?
Downloaded from ManualsPrinter.com Manuals How do I? 17

Chapter 4
How do I?
18 How do
Downloaded I? ManualsPrinter.com Manuals
from
5 Connection information
The HP All-in-One comes equipped with a USB port so you can connect directly to a
computer using a USB cable. You can also share the product over an existing home
network.
• Supported connection types
• Use printer sharing
Supported connection types

The following table contains a list of supported connection types.
Description Recommended number Supported software Setup instructions

of connected features
Connection information
computers for best
performance
USB connection One computer connected All features are Follow the Setup Guide
with a USB cable to the supported. for detailed instructions.
rear USB 1.1 full speed
peripheral connection
port on the HP All-in-One.
Printer sharing Up to five. All features resident on Follow the instructions in

the host computer are Use printer sharing.
The host computer must
supported. Only printing
be on at all times in order
is supported from the
to print from the other
other computers.
computers.
Use printer sharing

If your computer is on a network, and another computer on the network has an HP All-
in-One connected to it by a USB cable, you can print to that printer using printer sharing.
The computer directly connected to the HP All-in-One acts as the host for the printer and
has full software functionality. The other computer, which is referred to as a client, has
access only to the print features. You must perform other functions from the host
computer or from the control panel on the HP All-in-One.
To enable printer sharing on a Windows computer

▲ Refer to the user guide that came with your computer or see the Windows onscreen
Help.
Downloaded from ManualsPrinter.com Manuals Connection information 19

Chapter 5
Connection information
20 Connection
Downloaded information
6 Load originals and load paper
You can load many different types and sizes of paper in the HP All-in-One, including letter
or A4 paper, photo paper, transparencies, and envelopes.
• Load originals
• Choose papers for printing and copying
• Load paper
Load originals
You can copy or scan up to letter- or A4-size originals by loading them on the glass.
To load an original on the glass

1. Lift the lid on the HP All-in-One.
2. Place your original with the side you want to copy or scan face down on the left front
corner of the glass.
TIP: For more help on loading an original, refer to the engraved guides along the
edge of the glass.
TIP: To get the correct copy size, make sure that there is no tape or other foreign
object on the glass.
Load originals and load paper
3. Close the lid.
Choose papers for printing and copying

You can use different types and sizes of paper in the HP All-in-One. Review the following
recommendations to get the best printing and copying quality. Whenever you change
paper types, remember to change the paper type settings. For more information, see Set
the paper type for printing.
Downloaded from ManualsPrinter.com Manuals Load originals and load paper 21

Chapter 6

• Recommended papers for printing and copying
• Recommended papers for printing only
• Papers to avoid
Recommended papers for printing and copying

If you want the best print quality, HP recommends using HP papers that are specifically
designed for the type of project you are printing. If you are printing photos, for example,
load HP Premium or HP Premium Plus photo paper in the input tray.
The following is a list of HP papers you can use for copying and printing. Depending on
your country/region, some of these papers might not be available.
NOTE: To achieve a borderless print, you must use 10 x 15 cm (4 x 6 inch) paper

with tab. The HP All-in-One prints to the edge of three sides of the paper. When you
remove the tab from the fourth side, you have a borderless print.
HP Premium Plus Photo Paper

HP Premium Plus Photo Papers are the best HP photo papers, with image quality and
fade resistance superior to store-processed photos. They are ideal for printing your high-
resolution images for framing or including in a photo album. These papers are available
in several sizes, including 10 x 15 cm (4 x 6 inch) (with or without tabs), A4, and 8.5 x 11
inch sizes for printing or copying photos from the product.
HP Premium Photo Paper

HP Premium Photo Papers are high-quality, glossy-finish or soft gloss-finish photo
papers. They look and feel like store-processed photos and can be mounted under glass
or in an album. These papers are available in several sizes, including 10 x 15 cm (4 x 6

inch) (with or without tabs), A4, and 8.5 x 11 inch sizes for printing or copying photos from
the product.
HP Premium Inkjet Transparency Film

HP Premium Inkjet Transparency Film make your color presentations vivid and even more
impressive. This film is easy to use and handle and dries quickly without smudging.
HP Premium Inkjet Paper

HP Premium Inkjet Paper is the ultimate coated paper for high-resolution usage. A
smooth, matte finish makes it ideal for your highest-quality documents.
HP Bright White Inkjet Paper

HP Bright White Inkjet Paper delivers high-contrast colors and sharp text. It is opaque
enough for two-sided color usage with no show-through, which makes it ideal for
newsletters, reports, and flyers.
22 Load from
Downloaded originals and load paper
HP All-in-One Paper or HP Printing Paper
• HP All-in-One Paper is specifically designed for HP All-in-One products. It has an
extra bright blue-white shade that produces sharper text and richer colors than
ordinary multifunction papers.
• HP Printing Paper is a high-quality multifunction paper. It produces documents that
look and feel more substantial than documents printed on standard multipurpose or
copy paper.
To order HP papers and other supplies, go to www.hp.com/buy/supplies. If prompted,
choose your country/region, follow the prompts to select your product, and then click one
of the shopping links on the page.
NOTE: At this time, some portions of the HP Web site are available in English only.
Recommended papers for printing only

Certain papers are supported only when you start the print job from your computer. The
following list provides information about these papers.
If you want the best print quality, HP recommends using HP papers. Using paper that is
too thin or too thick, paper that has a slick texture, or paper that stretches easily can cause
paper jams. Using paper that has a heavy texture or does not accept ink can cause printed
images to smear, bleed, or not fill in completely.
Depending on your country/region, some of these papers might not be available.
HP Iron-On Transfers
HP Iron-On Transfers (for color fabrics or for light or white fabrics) are the ideal solution
for creating custom T-shirts from your digital photos.

HP Brochure & Flyer Paper
HP Brochure & Flyer Paper (Gloss or Matte) is glossy-coated or matte-coated on both
sides for two-sided use. They are the perfect choice for near-photographic reproductions
and business graphics for report covers, special presentations, brochures, mailers, and
calendars.
HP Premium Presentation Paper

HP Premium Presentation Paper gives your presentation a quality look and feel.
To order HP papers and other supplies, go to www.hp.com/buy/supplies. If prompted,
choose your country/region, follow the prompts to select your product, and then click one
of the shopping links on the page.
NOTE: At this time, some portions of the HP Web site are available in English only.
Papers to avoid
Using paper that is too thin or too thick, paper that has a slick texture, or paper that
stretches easily can cause paper jams. Using paper that has a heavy texture or does not
accept ink can cause printed images to smear, bleed, or not fill in completely.
Downloaded from ManualsPrinter.com Manuals Choose papers for printing and copying 23
Chapter 6
NOTE: For a complete list of supported media sizes, see the printer software.
Papers to avoid for all print and copy jobs

• Any size paper other than those listed in the printer software.
• Paper with cutouts or perforations (unless specifically designed for use with HP inkjet
devices).
• Highly textured stock, such as linen. It might not print evenly, and the ink can bleed
into these papers.
• Extremely smooth, shiny, or coated papers not specifically designed for the HP All-
in-One. They can jam the HP All-in-One or repel the ink.
• Multi-part forms, such as duplicate and triplicate forms. They can wrinkle or get stuck,
and the ink is more likely to smear.
• Envelopes with clasps or windows. They can get stuck in the rollers and cause paper
jams.
• Banner paper.
Additional papers to avoid when copying

• Envelopes.
• Transparency film other than HP Premium Inkjet Transparency Film or HP Premium
Plus Inkjet Transparency Film.
• Iron-On Transfers.
• Greeting card paper.
Load paper
This section describes the procedure for loading different types and sizes of paper into
the HP All-in-One for your copies or printouts.
TIP: To help prevent rips, wrinkles, and curled or bent edges, store all paper flat in
a resealable bag. If the paper is not stored properly, extreme changes in temperature
and humidity might result in curled paper that does not work well in the HP All-in-One.

• Load full-size paper
• Load 10 x 15 cm (4 x 6 inch) photo paper
• Load index cards
• Load envelopes
• Load other types of paper
Load full-size paper

You can load many types of letter or A4 paper into the input tray of the HP All-in-One.
24 Load from
To load full-size paper
1. Flip the tray extender up toward you.
NOTE: When you use legal-size paper, leave the tray extender closed.
2. Slide the paper-width guide to its outermost position.
3. Tap a stack of paper on a flat surface to align the edges, and then check the paper
for the following:

• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack are the same size and type.
Downloaded from ManualsPrinter.com Manuals Load paper 25

Chapter 6
4. Insert the stack of paper into the input tray with the short edge forward. Ensure that
the side you want to print on faces down. Slide the stack of paper toward the product
until it stops.
CAUTION: Make sure that the product is idle and silent when you load paper
into the input tray. If the product is servicing the print cartridges or otherwise
engaged in a task, you could push the paper too far forward, causing the product
to eject blank pages.
TIP: If you are using letterhead, insert the top of the page first with the side you
want to print on facing down. For more help on loading full-size paper and
letterhead, refer to the diagram engraved in the base of the input tray.
5. Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray
and is no higher than the top of the paper-width guide.
Load 10 x 15 cm (4 x 6 inch) photo paper

You can load 10 x 15 cm (4 x 6 inch) photo paper into the input tray of the HP All-in-One.
For the best results, use 10 x 15 cm (4 x 6 inch) HP Premium Plus Photo Paper or HP
Premium Photo Paper with tab.
NOTE: For borderless printing, the HP All-in-One only supports 10 x 15 cm (4 x 6

inch) photo paper with a tear-off tab. You can automatically adjust the settings in the
Properties dialog box to print a borderless 10 x 15 cm (4 x 6 inch) photo on
HP Premium Plus Photo Paper. Click the Printing Shortcuts tab, and then, in the
Printing Shortcuts list, select Photo printing-borderless.
26 Load from
TIP: To help prevent rips, wrinkles, and curled or bent edges, store all paper flat in
a resealable bag. If the paper is not stored properly, extreme changes in temperature
and humidity might result in curled paper that does not work well in the HP All-in-One.
To load photo paper in the input tray

1. Remove all paper from the input tray.
2. Insert the stack of photo paper into the far-right side of the input tray with the print
side or glossy side down and short edge forward. Slide the stack of photo paper
toward the product until it stops.
If you are using photo paper that has a tear-off tab, verify that the tab is pointing away
from the product.
TIP: For more help on loading small-size photo paper, refer to the guides
engraved in the base of the input tray for loading photo paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray

For best results, set the paper type before copying or printing.
Related topics
• Change the print settings for the current job
• Set the copy paper type
Load index cards

You can load index cards into the input tray of the HP All-in-One to print notes, recipes,
and other text.
NOTE: The HP All-in-One leaves a 1.2 cm (0.5 inch) border on one short edge.
Before printing many cards, print one test card to make sure that the border does not
crop your text.

Chapter 6
To load index cards in the input tray

2. Insert the stack of cards vertically (short edge facing outwards), with the side you
want to print on facing down, into the far-right side of the input tray. Slide the stack of
cards forward until it stops.
3. Slide the paper-width guide inward against the stack of cards until it stops.
Do not overload the input tray; make sure the stack of cards fits within the input tray
Related topics
Load envelopes
You can load one or more envelopes into the input tray of the HP All-in-One. Do not use
shiny or embossed envelopes or envelopes that have clasps or windows.
NOTE: For specific details on how to format text for printing on envelopes, consult
the help files in your word processing software. For best results, consider using a label
for the return address on envelopes.
28 Load from
To load envelopes
2. Insert one or more envelopes into the far-right side of the input tray, with the envelope
flaps on the left and facing up. Slide the stack of envelopes forward until it stops.
TIP: To avoid paper jams, tuck the flap inside each envelope.
TIP: For more help on loading envelopes, refer to the diagram engraved in the
base of the input tray.
3. Slide the paper-width guide inward against the stack of envelopes until it stops.
Do not overload the input tray; make sure the stack of envelopes fits within the input
tray and is not higher than the top of the paper-width guide.
Load other types of paper

The following papers require extra attention to load them properly.
NOTE: Not all paper sizes and paper types are available with all the functions on
the HP All-in-One. Some paper sizes and paper types can only be used if you are
starting a print job from the Print dialog box in a software application. They are not

available for copying. Papers that are only available for printing from a software
application are indicated as such.
HP Premium Inkjet Transparency Film

▲ Insert the film so that the white transparency strip (with arrows and the HP logo) is on
top and is going into the input tray first.
NOTE: The HP All-in-One cannot automatically detect the paper type. For best
results, set the paper type to transparency film in the software before printing onto
transparency film.
HP Iron-On Transfers (for printing only)

1. Flatten the transfer sheet completely before using it; do not load curled sheets.
TIP: To prevent curling, keep transfer sheets sealed in the original package until
you are ready to use them.
2. Locate the blue stripe on the nonprinting side of the transfer paper and then manually
feed one sheet at a time into the input tray with the blue stripe facing up.

Chapter 6
Related topics
• Set the paper type for printing
30 Load from
7 Print from your computer
The HP All-in-One can be used with any software application that allows printing. You
can print a range of projects, such as borderless images, newsletters, greeting cards,
iron-on transfers, and posters.
• Print from a software application
• Make the HP All-in-One the default printer
• Change the default print settings
• Printing shortcuts
• Perform special print jobs
• Stop a print job
• Resume a print job
Print from a software application

Most print settings are automatically handled by the software application. You need to
change the settings manually only when you change print quality, print on specific types
of paper or transparency film, or use special features.
To print from a software application

1. Make sure you have paper loaded in the input tray.
2. On the File menu in your software application, click Print.
3. Make sure the product is the selected printer.
4. If you need to change settings, click the button that opens the Properties dialog box.
Depending on your software application, this button might be called Properties,
Options, Printer Setup, Printer, or Preferences.
NOTE: When printing a photo, you must select options for the specific photo
paper and photo enhancement.
5. Select the appropriate options for your print job by using the features available in the
Advanced, Printing Shortcuts, Features, and Color tabs.
TIP: You can easily select the appropriate options for your print job by choosing
one of the predefined print tasks on the Printing Shortcuts tab. Click a type of
print task in the Printing Shortcuts list. The default settings for that type of print
task are set and summarized on the Printing Shortcuts tab. If necessary, you
can adjust the settings here and save your custom settings as a new printing
shortcut. To save a custom printing shortcut, select the shortcut and click Save
As. To delete a shortcut, select the shortcut and click Delete.
6. Click OK to close the Properties dialog box.

7. Click Print or OK to begin printing.
Print
Downloaded from ManualsPrinter.com Manuals Print from your computer 31

Chapter 7
Make the HP All-in-One the default printer

You can set the HP All-in-One as the default printer to use from all software applications.
This means that the HP All-in-One is automatically selected in the printer list when you
select Print from the File menu in a software application. The default printer is
automatically selected when you click the Print button in the toolbar of most software
applications. For more information, see the Windows Help.
Change the print settings for the current job

You can customize the print settings of the HP All-in-One to handle nearly any print task.
• Set the paper size
• View the print resolution
• Change the print speed or quality
• Change the page orientation
• Scale the document size
• Preview your print job
Set the paper size

The paper size setting helps the HP All-in-One determine the printable area on the page.
Some of the paper size choices have a borderless equivalent, which allows you to print
to the top, bottom, and side edges of the paper.
Usually, you set the paper size in the software application you used to create your
document or project. However, if you are using custom-size paper, or if you cannot set
the paper size from your software application, you can change the paper size in the
Properties dialog box before printing.
To set the paper size

4. Click the button that opens the Properties dialog box.
5. Click the Features tab.
6. In the Resizing Options area, click the appropriate paper size from the Size list.
The following table lists the suggested paper size settings for the different types of
paper you can load in the input tray. Make sure to look at the long list of choices in
Print
32 Print from
Downloaded fromyour computer
the Size list to see if a defined paper size already exists for the type of paper you are
using.
Paper type Suggested paper size settings
Copier, multi-purpose, or Letter or A4

plain papers
Envelopes Appropriate listed envelope size
Greeting-card papers Letter or A4
Index cards Appropriate listed card size (if listed sizes are not appropriate,
you can specify a custom paper size)
Inkjet papers Letter or A4
Iron-on T-shirt transfers Letter or A4
Labels Letter or A4
Legal Legal
Letterhead Letter or A4
Panorama photo paper Appropriate listed panorama size (if listed sizes are not
appropriate, you can specify a custom paper size)
Photo papers 10 x 15 cm (4 x 6 inch), letter, A4, or an appropriate listed size
Transparency films Letter or A4
Custom-size papers Custom paper size
Set the paper type for printing

If you print on special papers, such as photo paper, transparency film, envelopes, or
labels, or if you experience poor print quality, you can set the paper type manually.
To set the paper type for printing

6. In the Basic Options area, from the Paper Type drop-down list, select More.
7. Select the type of paper that you have loaded, and then click OK.
View the print resolution

The printer software displays the print resolution in dots per inch (dpi). The dpi varies
according to the paper type and print quality that you select in the printer software.
Print
Downloaded from ManualsPrinter.com Manuals Change the print settings for the current job 33
Chapter 7
To view the print resolution

6. In the Print Quality drop-down list, select the appropriate print quality setting for your
project.
7. In the Paper Type drop-down list, select the type of paper that you have loaded.
8. Click the Resolution button to view the print resolution dpi.
Change the print speed or quality

The HP All-in-One automatically chooses a print quality and speed setting depending on
the paper type setting you select. You can also change the print quality setting to
customize the speed and quality of the print process.
To select a print speed or quality

6. In the Print Quality drop-down list, select the appropriate quality setting for your
project.
NOTE: To view the maximum dpi that the product will print, click Resolution.
7. In the Paper Type drop-down list, select the type of paper that you have loaded.
Change the page orientation

The page orientation setting allows you to print your document vertically or horizontally
on the page.
Usually, you set the page orientation in the software application you used to create your
document or project. However, if you are using custom-size or special HP paper, or if you
cannot set the page orientation from your software application, you can change the page
orientation in the Properties dialog box before printing.
To change the page orientation

Print
34 Print from
6. In the Basic Options area, do one of the following:
• Click Portrait to print the document vertically on the page.
• Click Landscape to print the document horizontally on the page.
Scale the document size

The HP All-in-One allows you to print the document at a different size than the original.
To scale the document size

6. In the Resizing options area, click Scale to paper size, and then click the
appropriate paper size from the drop-down list.
Preview your print job

You can preview your print job before sending it to the HP All-in-One. This helps to prevent
wasting paper and ink on projects that do not print as expected.
To preview your print job

5. Select the print settings appropriate for your project on each of the tabs in the dialog
box.
7. Select the Show Preview Before Printing check box.
8. Click OK, and then click Print or OK in the Print dialog box.
Your print job displays in the preview window.
9. In the HP preview window, do one of the following:
• To print, click Start Printing.
• To cancel, click Cancel Printing.
Print
Downloaded from ManualsPrinter.com Manuals Change the print settings for the current job 35
Chapter 7
Change the default print settings

If there are settings that you frequently use for printing, you might want to make them the
default print settings so they are already set when you open the Print dialog box from
within your software application.
To change the default print settings

1. In the HP Solution Center, click Settings, point to Print Settings, and then click
Printer Settings.
2. Make changes to the print settings, and click OK.
Printing shortcuts
Use printing shortcuts to print with print settings that you use often. The printer software
has several specially designed printing shortcuts that are available in the Printing
Shortcuts list.
NOTE: When you select a printing shortcut the appropriate printing options are
automatically displayed. You can leave them as is or change them. You can also
create a shortcut. For more information, see Create printing shortcuts.
Use the Printing Shortcuts tab for the following print tasks:
• General Everyday Printing: Print documents quickly.
• Photo Printing–Borderless: Print to the top, bottom, and side edges of 10 x 15 cm
(4 x 6 inch) HP Premium Plus Photo Papers with a tear-off tab.
• Photo Printing–With White Borders: Print a photo with a white border around the
edges.
• Fast/Economical printing: Produce draft-quality printouts quickly.
• Presentation printing: Print high-quality documents, including letters and
transparencies.
• Two-sided (Duplex) Printing: Print two-sided pages with the HP All-in-One
manually.
• Create printing shortcuts
• Delete printing shortcuts
Related topics
• Print a borderless image
• Print a photo on photo paper
• Print on transparencies
• Print on both sides of the page
Create printing shortcuts

In addition to the printing shortcuts that are available in the Printing Shortcuts list, you
can create your own printing shortcuts.
If you frequently print on transparency film, for example, you can create a printing shortcut
by selecting the Presentation Printing shortcut, changing the paper type to HP Premium
Print
36 Print from
Inkjet Transparency Film, and then saving the modified shortcut under a new name; for
example, Transparency Presentations. After creating the printing shortcut, simply
select it when printing on transparency film rather than changing the print settings each
time.
To create a printing shortcut

4. Click the Printing Shortcuts tab.
5. In the Printing Shortcuts list, click a printing shortcut.
The print settings for the selected printing shortcut are displayed.
6. Change the print settings to those you want in the new printing shortcut.
7. Click Save as and type a name for the new printing shortcut, and then click Save.
The printing shortcut is added to the list.
Delete printing shortcuts

You might want to delete printing shortcuts that you no longer use.
To delete a printing shortcut

4. Click the Printing Shortcuts tab.
5. In the Printing Shortcuts list, click the printing shortcut that you want to delete.
6. Click Delete.
The printing shortcut is removed from the list.
NOTE: Only the shortcuts that you have created can be deleted. The original HP
shortcuts cannot be deleted.
Perform special print jobs

In addition to supporting standard print jobs, the HP All-in-One can perform special jobs
such as printing borderless images, iron-on transfers, and posters.
• Print a borderless image
• Print a photo on photo paper
• Print using Maximum dpi
• Print on both sides of the page
Print
Downloaded from ManualsPrinter.com Manuals Perform special print jobs 37

Chapter 7
• Print a multiple-page document as a booklet

• Print multiple pages on a single sheet
• Print a multiple-page document in reverse order
• Reverse an image for iron-on transfers
• Print on transparencies
• Print a group of addresses on labels or envelopes
• Print a poster
• Print a Web page
Print a borderless image

Borderless printing lets you print to the top, bottom, and side edges of 10 x 15 cm (4 x 6
inch) HP Premium Plus Photo Papers with a tear-off tab. When you remove the tear-off
tab, the printed image is borderless and extends to the edges of the paper.
TIP: You can automatically adjust the settings in the Properties dialog box to print
a borderless 10 x 15 cm (4 x 6 inch) photo on HP Premium Plus Photo Paper. Click
the Printing Shortcuts tab, and then, in the Printing Shortcuts list, select Photo
printing-borderless. You can also set the options manually as described in the
following procedure.
To print a borderless image

2. Place the photo paper, with the print side down and the short edge forward, on the
right side of the input tray. Verify that the tear-off tab is pointing away from the product.
Print
38 Print from
7. In the Size list, click the size of photo paper loaded in the input tray.
If a borderless image can be printed on the specified size, the Borderless printing
check box is enabled.
8. In the Paper Type drop-down list, click More, and then select the appropriate paper
type.
NOTE: You cannot print a borderless image if the paper type is set to Plain
paper or to a type of paper other than a photo paper.
9. Select the Borderless printing check box if it is not already checked.

If the borderless paper size and paper type are not compatible, the product software
displays an alert and allows you to select a different type or size.
NOTE: Do not leave unused photo paper in the input tray. The paper might start
to curl, which could reduce the quality of your printout. Photo paper should be flat
before printing.
Related topics
Load 10 x 15 cm (4 x 6 inch) photo paper
Print a photo on photo paper

To achieve the best print quality, HP recommends using HP papers that are specifically
designed for the type of project you are printing along with genuine HP ink. HP papers
and HP ink are specifically designed to work well together to provide high-quality output.
For photo printing, HP recommends that you use HP Premium Plus Photo Papers with
the HP All-in-One.
To print a photo on photo paper

1. Remove all paper from the input tray, and then load the photo paper print side down.

Print

Chapter 7
6. In the Basic Options area, select the appropriate photo paper type from the Paper
Type drop-down list.
If the paper size and paper type are not compatible, the product software displays an
alert and allows you to select a different type or size.
8. In the Basic Options area, select a high print quality, such as Best, from the Print
Quality drop-down list.
NOTE: For maximum dpi resolution, go to the Advanced tab, and then select
Enabled from the Maximum dpi drop-down list. For more information, see Print
using Maximum dpi.
9. In the HP Real Life Technologies area, click the Photo fix drop-down list and select
from the following options:
• Off: applies no HP Real Life Technologies to the image.
• Basic: enhances low-resolution images; moderately adjusts image sharpness.
• Full: automatically adjusts brightness, contrast, and sharpness; enhances low-
resolution images; automatically removes red-eye coloring in the photo.
TIP: You can remove red-eye coloring in the photo when using the Off or
Basic mode by selecting the Remove red eye check box.
10. Click OK to return to the Properties dialog box.

11. (Optional) If you want to print the photo in black and white, click the Color tab and
select the Print in grayscale check box. From the drop-down list, select one of the
following options:
• High Quality: uses all the available colors to print your photo in grayscale. This
creates smooth and natural shades of gray.
• Black Ink Only: uses black ink to print your photo in grayscale. The gray shading
is created by varying patterns of black dots, which might result in a grainy image.
NOTE: Do not leave unused photo paper in the input tray. The paper might start to
curl, which could reduce the quality of your printout. Photo paper should be flat before
printing.
Print using Maximum dpi

Use Maximum dpi mode to print high-quality, sharp images.
To get the most benefit from Maximum dpi mode, use it to print high-quality images such
as digital photographs. When you select the Maximum dpi setting, the printer software
displays the optimized dots per inch (dpi) that the HP All-in-One will print.
Printing in Maximum dpi takes longer than printing with other settings and requires a
large amount of disk space.
NOTE: If a photo print cartridge is also installed, the print quality is enhanced. A
photo print cartridge can be purchased separately if it is not included with the HP All-
in-One. Photo print cartridges are not supported on all models of the product.
Print
40 Print from
To print in Maximum dpi mode
5. Click the Advanced tab.
6. In the Printer Features area, select Enabled from the Maximum dpi drop-down list.
8. In the Paper Type drop-down list, click More, and then select the appropriate paper
type.
9. In the Print Quality drop-down list, click Maximum dpi.
NOTE: To view the maximum dpi that the product will print, click Resolution.
10. Select any other print settings that you want, and then click OK.
Related topics
Work with print cartridges
Print on both sides of the page

You can print two-sided pages with the HP All-in-One manually. When printing two-sided
pages, make sure to use paper that is thick enough so that images do not show through
to the other side.
To print on both sides of the page

1. Load paper into the input tray.
6. In the Paper saving options area, select Manual from the Two-sided printing drop-
down list.
Print

Chapter 7
7. For binding, do one of the following:

• For binding on the top like a notebook or calendar, select the Flip Pages Up check
box.
This causes the odd and even pages of your document to print opposite of each
other top-to-bottom. This ensures that the top of the page is always at the top of
the sheet when you flip the pages up in your bound document.
• For binding on the side like a book or magazine, click to clear the Flip Pages
Up check box.
This causes the odd and even pages of your document to print opposite of each
other left-to-right. This ensures that the top of the page is always at the top of the
sheet when you turn the pages in your bound document.
The product begins printing. Wait until all the odd-numbered pages are printed before
removing any of the printed pages from the output tray.
A dialog box displays instructions on the screen when it is time to process the second
side of your job.
9. Click Continue when done.
Print a multiple-page document as a booklet

The HP All-in-One allows you to print your document as a small booklet, which you can
fold and then staple together.
For best results, design your document to fit on a multiple of four pages, such as an 8,
12, or 16-page program for a child's school play or for a wedding.
11 9 7
1 3 5
Print
42 Print from
To print a multiple-page document as a booklet
1. Load paper into the input tray.
The paper should be thick enough so that the images do not show through to the
other side.
6. In the Paper saving options area, select Manual from the Two-sided printing drop-
down list.
7. Select the binding edge from the Booklet layout is list, as appropriate for your
language.
• If your language reads left-to-right, click Left edge binding.
• If your language reads right-to-left, click Right edge binding.
The Pages per sheet box is automatically set to two pages per sheet.
The product begins printing.
A dialog box displays instructions on the screen when it is time to process the second
side of your job. Do not click Continue in the dialog box until you have reloaded the
paper as instructed in the following steps.
9. Wait until the product has stopped printing for several seconds before removing any
of the printed pages from the output tray.
If you remove the pages while the document is still printing, the pages might get out
of order.
10. Follow the instructions that appear on your screen for reloading the paper to print on
the second side, and then click Continue.
11. When the entire document has finished printing, fold the stack of paper in half, so that
the first page is on top, then staple the document along the crease.
TIP: For best results, use a saddle stapler, or a heavy-duty stapler with a long
reach to staple the booklet.
Print

Chapter 7
Figure 7-1 Left-edge binding for left-to-right languages
Figure 7-2 Right-edge binding for right-to-left languages

Print
44 Print from
Print multiple pages on a single sheet
You can print up to 16 pages on a single sheet of paper.
1 2
3 4
To print multiple pages on a single sheet

6. In the Pages per sheet list, click 2, 4, 6, 9, or 16.
7. If you want a border to appear around each page image printed on the sheet of paper,
select the Print page borders check box.
8. In the Page order list, click an appropriate page order option.
The sample output graphic is numbered to show how the pages will be ordered if you
select each option.
Print

Chapter 7
Print a multiple-page document in reverse order

Because of the way the paper feeds through the HP All-in-One, the first page that prints
is print side up at the bottom of the stack. Usually this means you need to put the printed
pages in the correct order.
A better way is to print the document in reverse order so that the pages are stacked
correctly.
TIP: Set this option as a default setting so you do not have to remember to set it
every time you print a multiple-page document.
To print a multiple-page document in reverse order

6. In the Layout Options area, select Front to Back in the Page Order option.
NOTE: If you set your document to print on both sides of the page, the Front to
Back option is not available. Your document will automatically print in the correct
order.
NOTE: When you are printing multiple copies, each set is printed completely
before the next set is printed.
Print
46 Print from
Reverse an image for iron-on transfers
This feature reverses an image so you can use it for iron-on transfers. This feature is also
useful for transparencies when you want to make notations on the back of the
transparency without scratching the original.
To reverse an image for iron-on transfers

5. In the Paper Type drop-down list, click More, and then select HP Iron-on Transfer
from the list.
6. If the selected size is not what you want, click an appropriate size in the Size list.
8. In the Printer Features area, select On from the Mirror Image drop-down list.
NOTE: To prevent jams, manually feed the iron-on transfer sheets into the input
tray one sheet at a time.
Print on transparencies
For the best results, HP recommends you use HP transparency products with the HP All-
in-One.
To print on transparencies
1. Load the transparency into the input tray.
Print

Chapter 7
6. In the Basic Options area, from the Paper Type drop-down list, select More. Then
select the appropriate paper type.
TIP: If you want to make notations on the back of the transparencies and erase
them later without scratching the original, click the Advanced tab, and select the
Mirror Image check box.
7. In the Resizing Options area, from the Size drop-down list, select More. Then, select
an appropriate size.
NOTE: The product automatically waits for transparencies to dry before

releasing them. Ink dries slower on film than on plain paper. Make sure you allow
enough time for the ink to dry before handling the transparency.
Print a group of addresses on labels or envelopes

With the HP All-in-One, you can print on a single envelope, a group of envelopes, or label
sheets designed for inkjet printers.
To print a group of addresses on labels or envelopes

1. Print a test page on plain paper first.
2. Place the test page on top of the label sheet or envelope, and hold both up to the
light. Check the spacing for each block of text. Make adjustments as needed.
3. Load the labels or envelopes into the input tray.
CAUTION: Do not use envelopes with clasps or windows. They can get stuck in
the rollers and cause paper jams.
4. If you are printing on envelopes, do the following:

a. Display the print settings, and click the Features tab.
b. In the Resizing Options area, click the appropriate envelope size in the Size list.
Related topics
Load envelopes
Print
48 Print from
Print a poster
You can create a poster by printing a document on multiple pages. The HP All-in-One
prints dotted lines on some pages to indicate where to trim the pages before taping them
together.
To print a poster
6. Expand Document Options, and then expand Printer Features.
7. In the Poster Printing drop-down list, click either 2x2 (4 sheets), 3x3 (9 sheets),
4x4 (16 sheets), or 5x5 (25 sheets).
This selection tells the product to enlarge your document so that it fits on 4, 9, 16, or
25 pages.
If your originals are of multiple pages, each of those pages will be printed on 4, 9, 16,
or 25 pages. For example, if you have a one-page original and you select 3x3, you
will get 9 pages; if you select 3x3 for a two-page original, 18 pages will print.
9. After the poster has printed, trim the edges of the sheets and tape the sheets together.
Print a Web page

You can print a Web page from your Web browser on the HP All-in-One.
If you use Internet Explorer 6.0 or higher for Web browsing, you can use HP Smart Web
Printing to ensure simple, predictable web printing with control over what you want and
how you want it printed. You can access HP Smart Web Printing from the toolbar in
Internet Explorer. For more information about HP Smart Web Printing, see the help file
provided with it.
Print

Chapter 7
To print a Web page

2. On the File menu in your Web browser, click Print.
TIP: For best results, select HP Smart Web Printing on the File menu. A check
mark appears when it is selected.
The Print dialog box appears.
4. If your Web browser supports it, select the items on the Web page that you want to
include in the printout.
For example, in Internet Explorer, click the Options tab to select options such as As
laid out on screen, Only the selected frame, and Print all linked documents.
5. Click Print or OK to print the Web page.
TIP: To print Web pages correctly, you might need to set your print orientation to
Landscape.
Stop a print job

Although you can stop a print job from either the HP All-in-One or the computer, HP
recommends you stop it from the HP All-in-One for best results.
To stop a print job from the product

▲ Press Cancel. If the print job does not stop, press Cancel again.
It can take a few moments for the print job to be cancelled.
To stop a print job from the computer (Windows Vista users)

1. On the Windows taskbar, click Start, and then click Control Panel.
2. Click Printers.
3. Double-click the product icon.
TIP: You can also double-click the printer icon in the Windows taskbar.
4. Select the print job you want to cancel.

5. On the Document menu, click Cancel Printing or Cancel, or press the Delete key
on your keyboard.
To stop a print job from the computer (Windows XP users)

2. Open the Printers and Faxes control panel.
Print
50 Print from
5. On the Document menu, click Cancel Printing or Cancel, or press the Delete key
on your keyboard.
To stop a print job from the computer (Windows 2000 users)

1. On the Windows taskbar, click Start, point to Settings, and then click Printers.

4. On the Document menu, click Cancel or press the Delete key on your keyboard.
Related topics
Resume a print job

If an error occurs while printing, you may need to resume the job from the HP All-in-One
or the computer after you address the error.
To resume a print job from the control panel

▲ On the control panel, press any button.
To resume a print job from the computer (Windows Vista users)

2. Click Printers.
4. Select the print job you want to resume.

5. On the Document menu, click Resume Printing or Resume.
It can take a few moments to resume the print job.
To resume a print job from the computer (Windows XP users)

2. Open the Printers and Faxes control panel.

5. On the Document menu, click Resume Printing or Resume.
Print
Downloaded from ManualsPrinter.com Manuals Resume a print job 51

Chapter 7
To resume a print job from the computer (Windows 2000 users)

1. On the Windows taskbar, click Start, point to Settings, and then click Printers.

4. On the Document menu, click Resume.
Related topics
Print
52 Print from
8 Use the copy features
The HP All-in-One allows you to produce high-quality color and black-and-white copies
on a variety of paper types. You can enlarge or reduce the size of an original to fit a
Use the copy features

specific paper size, adjust the copy quality, and make high-quality copies of photos,
including borderless copies.

• Make a copy
• Change copy speed
• Make multiple copies of the same original
• Copy a two-page black-and-white document
• Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo
• Stop copying
Make a copy
You can make quality copies from the control panel.
To make a copy from the control panel

TIP: For quality copies, ensure that the scanner glass is clean and that there are
no foreign materials adhering to it. For more information, see Clean the glass.
3. Press the Paper Type button to set the paper type.

4. Press Start Copy Black or Start Copy Color.
Related topics
Set the copy paper type

You can set the paper type for copying to either Plain or Photo.
To set the paper type for copies

Downloaded from ManualsPrinter.com Manuals Use the copy features 53

Chapter 8

Copies made on photo paper are automatically made using Best quality. When Photo
Paper is selected, the HP All-in-One enlarges or shrinks the original to fit within the
copy margin of the detected paper size.
Copies made on plain paper are automatically made using Normal quality. When the
Plain Paper is selected, the HP All-in-One makes an exact copy of the original placed
on the scanner glass.
NOTE: Ensure that the scanner glass is clean for the copy function to work
properly.
4. Press Start Copy Black or Start Copy Color.

Refer to the following table to determine which paper type setting to choose based on the
paper loaded in the input tray.
Paper type Control panel setting
Copier paper or letterhead Plain
HP Bright White Paper Plain
HP Premium Plus Photo Paper, Glossy Photo
HP Premium Plus Photo Paper, Matte Photo
HP Premium Plus 4 x 6 inch Photo Paper Photo
HP Photo Paper Photo
HP Everyday Photo Paper Photo
HP Everyday Photo Paper, Semi Gloss Photo
Other photo paper Photo
HP Premium Paper Plain
HP All-in-One Paper Plain
HP Printing Paper Plain
Other inkjet paper Plain
Legal Plain
Related topics
Change copy speed

Copies made from the control panel on regular, plain paper automatically use Normal
quality.
You can make a Fast copy using the instructions below. Fast copies faster with
comparable quality text, but the graphics quality might be lower. Fast copies use less ink
and extend the life of your print cartridges.
54 Use the
Downloaded copy
from features
NOTE: Fast or Normal are not available when the paper type is set to Photo.
To make a Fast copy



4. Press and hold down the Scan button, and then press either Start Copy Black or
Start Copy Color.
Related topics
Set the copy paper type
Make multiple copies of the same original

You can set the number of copies from the control panel or from the software that you
installed with the HP All-in-One.
To make multiple copies of an original from the control panel


4. Press the Start Copy Black or Start Copy Color button to increase the number of
copies up to a maximum of 9 (varies by model). The product starts the copy job after
the last button press.
TIP: Use the software that you installed with the product to set the number of
copies higher than 9.
In this example, the product makes six copies of the original 10 x 15 cm (4 x 6 inch)
photo.
Downloaded from ManualsPrinter.com Manuals Make multiple copies of the same original 55
Chapter 8
Related topics
Copy a two-page black-and-white document

You can use the HP All-in-One to copy a single- or multiple-page document in color or
black and white. In this example, the HP All-in-One is used to copy a two-page black-
and-white original.
To copy a two-page document from the control panel

4. Press Start Copy Black.
5. Wait until the product has finished printing the first page. Remove the first page from
the glass and load the second page.
6. Press Start Copy Black.
Related topics
Make a 10 x 15 cm (4 x 6 inch) borderless copy of a photo

To make a borderless copy of a photo, use the 10 x 15 cm (4 x 6 inch) HP Premium Plus
Photo Paper with a tear-off tab. When you remove the tear-off tab, the output is a
borderless copy of the image that extends to the edges of the paper.
56 Use the
Downloaded copy
from features
To make a borderless copy of a photo from the control panel
1. Load 10 x 15 cm (4 x 6 inch) tabbed photo paper in the input tray. Verify that the tab
is pointing away from the product.

NOTE: To make a borderless copy, you must use tabbed photo paper.
2. Load your original print side down on the left front corner of the glass.
3. Press Paper Type to select the Photo paper type.
NOTE: When the Photo paper type is selected, the HP All-in-One defaults to
making a borderless copy with a 10 x 15 cm (4 x 6 inch) original.
4. Press Start Copy Color.

Remove the tab to make the copy completely borderless.
Related topics
Stop copying
To stop copying
▲ Press Cancel on the control panel.
Downloaded from ManualsPrinter.com Manuals Stop copying 57

Chapter 8
Related topics
58 Use the
Downloaded copy
from features
9 Use the scan features
Scanning is the process of converting text and pictures into an electronic format for your
computer. You can scan almost anything (photos, magazine articles and text documents)
on the HP All-in-One.
NOTE: When scanning, the HP Photosmart Software enables you to save an image
in the following file formats: BMP, DCX, FPX, GIF, JPG, PCD, PCX, and TIF.
You can use the scanning features of the HP All-in-One to do the following:
• Scan text from an article into your word processor and quote it in a report.
• Print business cards and brochures by scanning a logo and using it in your publishing
software.
• Send photos to friends and relatives by scanning your favorite prints and including
them in e-mail messages.
• Create a photographic inventory of your house or office.
• Archive treasured photos in an electronic scrapbook.
NOTE: If you are using the HP Photosmart Software, the Optical Character
Recognition (OCR) software might not be installed on your computer. To install the
Scan
OCR software, you must re-insert the software disk and select OCR under the
Custom installation options.

• Scan an original
• Edit a scanned preview image
• Edit a scanned image
• Edit a scanned document
• Stop scanning
Scan an original
For original documents or images placed on the glass, you can start a scan from your
computer or from the HP All-in-One. This section explains the second option: how to scan
from the control panel of the HP All-in-One to a computer.
To use the scan features, the HP All-in-One and computer must be connected and turned
on. The HP Photosmart Software must also be installed and running on your computer
prior to scanning. To verify that the HP Photosmart Software is running on a Windows
Downloaded from ManualsPrinter.com Manuals Use the scan features 59

Chapter 9
computer, look for the HP Digital Imaging Monitor icon in the system tray at the lower
right side of the screen, near the time.
NOTE: Closing the HP Digital Imaging Monitor icon in the Windows system tray
can cause the HP All-in-One to lose some of its scan functionality. If this happens,
Scan
you can restore full functionality by restarting your computer or by starting the
HP Photosmart Software.
The HP Photosmart Software that you installed on your computer has many tools that
you can use to edit and print your scanned image. You can improve the overall image
quality by adjusting the brightness, sharpness, color tone, or saturation. You can also
crop, straighten, rotate, or resize the image. When the scanned image looks just the way
you want it, you can open it in another application, send it through e-mail, save it to a file,
or print it.
60 Use the
Downloaded scan
from features
To scan to a computer
2. Press Scan.
The product scans the original automatically. A preview image of the scan appears
on your computer, where you can edit it. Any edits that you make apply to the current
scan session only.
The HP Photosmart Software has many tools that you can use to edit your scanned
image. You can improve the overall image quality by adjusting the brightness,
sharpness, color tone, or saturation. You can also crop, rotate, or resize the image.
3. Make any edits to the preview image, and then click Accept when you are finished.
Related topics
Edit a scanned preview image

You can use the tools in the HP Scanning software to modify a preview image. Any
changes that you make, such as brightness, image type, resolution, and more apply only
to this scan session.
Scan
You can make additional changes in the HP Photosmart software after the image is
scanned.
Related topics
Edit a scanned image

You can edit a scanned image, such as a photo or graphic, using the software you
installed with the HP All-in-One. Using this software, you can rotate or crop the image,
as well as adjust the brightness, contrast, and color saturation.
Related topics
Edit a scanned document

You can edit a scanned document using your Optical Character Recognition (OCR)
software. Scanning text using OCR software enables you to bring the content of magazine
articles, books, and other printed matter into your favorite word processor and many other
Downloaded from ManualsPrinter.com Manuals Edit a scanned preview image 61

Chapter 9
applications as editable text. Learning to use OCR software correctly is important if you
want to obtain the best results. Do not expect scanned text documents to be letter-perfect
the first time you use your OCR software. Using OCR software is an art that takes time
and practice to master.
Related topics
Stop scanning
To stop scanning
▲ Press Cancel on the control panel.
Related topics
Scan
62 Use the
Downloaded scan
from features
10 Maintain the HP All-in-One
The HP All-in-One requires little maintenance. Sometimes you might want to clean the
glass and lid backing to remove surface dust and ensure that your copies and scans
remain clear. You will also need to replace, align, or clean your print cartridges from time
to time. This section provides instructions for keeping the HP All-in-One in top working
condition. Perform these simple maintenance procedures as necessary.
• Clean the HP All-in-One
• Print a self-test report
• Work with print cartridges
Clean the HP All-in-One

To ensure that your copies and scans remain clear, you might need to clean the glass
and lid backing. You might also want to dust the exterior of the HP All-in-One.
• Clean the exterior
• Clean the glass
• Clean the lid backing
Clean the exterior

Use a soft cloth or slightly moistened sponge to wipe dust, smudges, and stains off the
case. The interior of the HP All-in-One does not require cleaning. Keep fluids away from
the control panel and the interior of the HP All-in-One.
Maintain the HP All-in-One

CAUTION: To avoid damage to the exterior of the HP All-in-One, do not use alcohol
or alcohol-based cleaning products.
Clean the glass

Fingerprints, smudges, hair, and dust on the main glass surface slow down performance
and affect the accuracy of the copy and scan features.
To clean the glass

1. Turn off the product, unplug the power cord, and raise the lid.
2. Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive
glass cleaner.
CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on

the glass, since they can damage it. Do not place or spray liquid directly on the
glass. The liquid might seep under the glass and damage the product.
Downloaded from ManualsPrinter.com Manuals Maintain the HP All-in-One 63

Chapter 10
3. Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4. Plug in the power cord, and then turn on the product.
Clean the lid backing

Minor debris can accumulate on the white document backing located underneath the lid
of the HP All-in-One.
To clean the lid backing

1. Turn off the product, unplug the power cord, and raise the lid.
2. Clean the white document backing with a soft cloth or sponge slightly moistened with
a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3. Dry the backing with a dry, soft, lint-free cloth.
CAUTION: Do not use paper-based wipes, as these might scratch the backing.
64 Maintain
Downloaded fromtheManualsPrinter.com
HP All-in-One Manuals
4. If further cleaning is needed, repeat the previous steps using isopropyl (rubbing)
alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual
alcohol.
CAUTION: Be careful not to spill alcohol on the glass or exterior of the product,
as this might damage it.
5. Plug in the power cord, and then turn on the product.
Print a self-test report

If you are experiencing problems with printing, print a self-test report before you replace
the print cartridges. This report provides useful information on several aspects of your
product, including your print cartridges.
To print a self-test report

1. Load letter or A4 unused plain white paper into the input tray.
2. Press and hold the Cancel button and then press the Start Copy Color button.
The product prints a self-test report, which might indicate the source of the printing
problem. A sample of the ink test area of the report is shown below.
3. Make sure the test patterns show a complete grid and the thick color lines are
complete.

• If more than a few lines in a pattern are broken, this might indicate a problem with
the nozzles. You might need to clean the print cartridges.
• If the black line is missing, faded, streaked, or shows lines, this might indicate a
problem with the black or photo print cartridge in the right slot.
• If any of the color lines are missing, faded, streaked, or show lines, this might
indicate a problem with the tri-color print cartridge in the left slot.
Related topics
• Clean the print cartridges
• Replace the print cartridges
Work with print cartridges

To ensure the best print quality from the product, you will need to perform some simple
maintenance procedures. This section provides guidelines for handling the print
cartridges and instructions for replacing, aligning, and cleaning the print cartridges.
You might also need to check your print cartridges if the Check Print Cartridge light is on.
This might mean that the print cartridges are not installed properly or are missing, the
Downloaded from ManualsPrinter.com Manuals Print a self-test report 65

Chapter 10
plastic tape has not been removed from the print cartridges, the print cartridges are low
on ink, or the print carriage is blocked.
• Handle the print cartridges
• Check the estimated ink levels
• Use ink-backup mode
• Use a photo print cartridge
• Store the print cartridges
• Align the print cartridges
• Clean the print cartridges
• Clean the print cartridge contacts
• Clean the area around the ink nozzles
• Remove ink from your skin and clothing
Handle the print cartridges

Before you replace or clean a print cartridge, you should know the part names and how
to handle the print cartridges.
1 Copper-colored contacts
2 Plastic tape with pink pull tab (must be removed before installing)
3 Ink nozzles under tape
Hold the print cartridges by their black plastic sides, with the label on top. Do not touch
the copper-colored contacts or the ink nozzles.
66 Maintain
NOTE: Handle the print cartridges carefully. Dropping or jarring cartridges can cause
temporary printing problems, or even permanent damage.
Check the estimated ink levels

You can easily check the ink supply level to determine how soon you might need to
replace a print cartridge. The ink supply level shows an estimate of the amount of ink
remaining in the print cartridges. Actual ink levels may vary.
TIP: You can also print a self-test report to see if your print cartridges might need to
be replaced.
NOTE: If the print cartridges were used before being installed in the product, or have
been refilled, the estimated ink levels on the Estimated Ink levels tab may be
inaccurate or unavailable.
NOTE: Ink from the cartridges is used in the printing process in a number of different
ways, including in the initialization process, which prepares the product and cartridges
for printing, and in print head servicing, which keeps print nozzles clear and ink flowing
smoothly. In addition, some residual ink is left in the cartridge after it is used. For more
information, see www.hp.com/go/inkusage.
To check the ink levels from the HP Photosmart Software

Printer Toolbox.
NOTE: You can also open the Printer Toolbox from the Print Properties dialog
box. In the Print Properties dialog box, click the Features tab, and then click the
Printer Services button.
The Printer Toolbox appears.

2. Click the Estimated Ink Level tab.
The estimated ink levels for the print cartridges appear.
Related topics
Print a self-test report
Replace the print cartridges

When the ink level for the print cartridge is low, a message appears on your computer
screen. You can also check the ink levels by using the software installed with the HP All-
in-One. Follow these instructions when the ink level is low.
NOTE: Ink level warnings and indicators provide estimates for planning purposes
only. When you receive a low-ink warning message, consider having a replacement
cartridge available to avoid possible printing delays. You do not need to replace the
print cartridges until print quality becomes unacceptable.
Downloaded from ManualsPrinter.com Manuals Work with print cartridges 67

Chapter 10
To order print cartridges for the HP All-in-One, go to www.hp.com/buy/supplies. If

prompted, choose your country/region, follow the prompts to select your product, and
then click one of the shopping links on the page.
Choose the right cartridge combination

Choose the best combination of cartridges for your print job:
• Everyday printing: Use a black cartridge along with a tri-color cartridge.
• Color photos: Use a photo cartridge along with a tri-color cartridge.
photo print cartridge can be purchased separately if it is not included with the
HP All-in-One. Photo print cartridges are not supported on all models of the
product.
To replace the print cartridges

1. Make sure the product is on and you have letter or A4 unused plain white paper loaded
in the input tray.
CAUTION: If the product is turned off when you open the print cartridge door to
access the print cartridges, it will not release the cartridges for changing. You
might damage the product if the print cartridges are not docked safely when you
try to remove them.
2. Open the print cartridge door.

The print carriage should move to the center of the product. If the print carriage does
not move to the center, turn the product off, and then on.
3. Wait until the print carriage is idle and silent, and then lightly press down on a print
cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the
slot on the left.
68 Maintain
If you are replacing the black or photo print cartridge, remove the print cartridge from
the slot on the right.
1 Print cartridge slot for the tri-color print cartridge

2 Print cartridge slot for the black and photo print cartridges
4. Pull the print cartridge toward you out of its slot.

5. If you are removing the black print cartridge in order to install the photo print cartridge,
store the black print cartridge in the print cartridge protector or an airtight plastic
container.
If you are disposing of the print cartridge, recycle the print cartridge. The HP Inkjet
Supplies Recycling Program is available in many countries/regions, and lets you
recycle used print cartridges free of charge. For more information, go to the following
Web site:
www.hp.com/hpinfo/globalcitizenship/environment/recycle/inkjet.html
6. Remove the new print cartridge from its packaging, being careful to touch only the
black plastic. Gently remove the plastic tape using the pink pull tab.
CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching

these parts can result in clogs, ink failure, and bad electrical connections.

Chapter 10
7. Slide the new print cartridge at a slight upward angle into the empty slot. Then gently
push on the upper part of the print cartridge forward until it snaps into place.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black or photo print cartridge, slide it into the right slot.
8. Close the print cartridge door.

9. After the print cartridge alignment sheet prints, load it on the left front corner of the
glass with the top of the page to the left.
70 Maintain
10. Press the Scan button.
The product aligns the print cartridges. Recycle or discard the print cartridge
alignment sheet.
Related topics
• Check the estimated ink levels
Use ink-backup mode

Use the ink-backup mode to operate the HP All-in-One with only one print cartridge. The
ink-backup mode is initiated when a print cartridge is removed from the print cartridge
carriage. During ink-backup mode, the product can only print jobs from the computer.
You cannot initiate a print job from the control panel (such as copying or scanning an
original).
NOTE: When the HP All-in-One operates in ink-backup mode, a message is

displayed on screen. If the message is displayed and two print cartridges are installed
in the product, verify that the protective piece of plastic tape has been removed from
each print cartridge. When plastic tape covers the print cartridge contacts, the product
cannot detect that the print cartridge is installed.
For more information about ink-backup mode, see the following topics:
• Ink-backup mode output
• Exit ink-backup mode
Ink-backup mode output

Printing in ink-backup mode slows the HP All-in-One and affects the quality of printouts.

Installed print cartridge Result
Black print cartridge Colors print as grayscale.
Tri-color print cartridge Colors print but black is grayed and is not a true black.
Photo print cartridge Colors print as grayscale.
NOTE: HP does not recommend using the photo print cartridge for ink-backup mode.
Exit ink-backup mode

Install two print cartridges in the HP All-in-One to exit ink-backup mode.
For information about installing a print cartridge, see Replace the print cartridges.
Use a photo print cartridge

You can optimize the quality of the color photos you print and copy with the HP All-in-
One by purchasing a photo print cartridge. Remove the black print cartridge and insert
the photo print cartridge in its place. With the tri-color print cartridge and photo print
cartridge installed, you have a six-ink system, which provides enhanced quality color
photos.

Chapter 10
When you want to print regular text documents, swap the black print cartridge back in.
Use a print cartridge protector or an airtight plastic container to keep your print cartridge
secure when it is not being used.
photo print cartridge can be purchased separately if it is not included with the HP All-
in-One. Photo print cartridges are not supported on all models of the product.
Related topics
Store the print cartridges

Follow these guidelines to maintain and store HP print cartridges and to ensure consistent
print quality.
• Print cartridge storage and handling
• Print cartridge protector
Print cartridge storage and handling

Follow these guidelines to help maintain HP print cartridges and ensure consistent print
quality:
• When you remove a print cartridge from the device, store it in an airtight plastic
container to prevent the ink from drying out. If you are storing a photo print cartridge,
you can use a print cartridge protector. For more information, see Print cartridge
protector.
• Keep all unused print cartridges in their original sealed packages until they are
needed. Store print cartridges at room temperature (15–35 degrees C or 59–95
degrees F).
• Do not remove the plastic tape covering the ink nozzles until you are ready to install
the print cartridge in the device. If the plastic tape has been removed from the print
cartridge, do not attempt to reattach it. Reattaching the tape damages the print
cartridge.
CAUTION: Always turn the HP All-in-One off with the Power button before you
unplug the power cord or turn off a power strip. This allows the device to store the
print cartridges properly. When you store the HP All-in-One, always leave the active
print cartridges inside the device.
Print cartridge protector

In some countries/regions, when you purchase a photo print cartridge (not supported on
all models of the product), you might also receive a print cartridge protector. If a print
cartridge protector is not available, you can use an airtight plastic container to protect
your print cartridge.
The print cartridge protector is designed to keep a print cartridge secure and prevent it
from drying out when it is not being used. Whenever you remove a print cartridge from
the HP All-in-One with the intention of using it again later, store it in the print cartridge
protector. For example, store the black print cartridge in a print cartridge protector if you
72 Maintain
are removing it so you can print high-quality photos with the photo and tri-color print
cartridges.
To insert a print cartridge into the print cartridge protector

▲ Place the print cartridge into the print cartridge protector at a slight angle and snap it
securely into place.
To remove the print cartridge from the print cartridge protector

▲ Press down on the top of the print cartridge protector to release the print cartridge,
and then gently remove the print cartridge out of the print cartridge protector.

Align the print cartridges
Aligning the print cartridges ensures high-quality output. The HP All-in-One prompts you
to align and calibrate the print cartridges every time you install a new print cartridge. Make
sure you align the print cartridges when prompted to ensure excellent print quality.
NOTE: If you remove and reinstall the same print cartridge, the HP All-in-One will
not prompt you to align the print cartridges. The HP All-in-One remembers the
alignment values for that print cartridge, so you do not need to realign the print
cartridges.

Chapter 10
To align newly installed print cartridges

1. Make sure you have letter or A4 unused plain white paper loaded in the input tray.
The HP All-in-One prints a print cartridge alignment sheet.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
If the alignment fails again, you might have a defective sensor or print cartridge.
Contact HP Support. Go to www.hp.com/support. If prompted, choose your
country/region, and then click Contact HP for information on calling for technical
support.
2. Load the print cartridge alignment sheet print side down on the left front corner of the
glass with the top of the page to the left.
The HP All-in-One aligns the print cartridges. Recycle or discard the print cartridge
alignment sheet.
To align the print cartridges from the HP Photosmart Software

NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
Printer Toolbox.

3. Click the Device Services tab.
4. Click Align the Print Cartridges.
The HP All-in-One prints a print cartridge alignment sheet.
5. Load the print cartridge alignment sheet print side down on the left front corner of the
glass.
The HP All-in-One aligns the print cartridges. Recycle or discard the print cartridge
alignment sheet.
Related topics
Clean the print cartridges

Use this feature when the self-test report shows streaking, white lines through any of the
lines of color or when a color is muddy after installing a print cartridge for the first time.
74 Maintain
Do not clean print cartridges unnecessarily, as this wastes ink and shortens the life of the
ink nozzles.
To clean the print cartridges from the HP Photosmart Software

1. Load letter, A4, or legal unused plain white paper into the input tray.
Printer Toolbox.
3. Click the Device Services tab.
4. Click Clean the Print Cartridges.
5. Follow the prompts until you are satisfied with the quality of the output, and then click
Done.
If print quality still seems poor after you clean the print cartridges, try cleaning the
print cartridge contacts before replacing the affected print cartridge.
Related topics
• Clean the print cartridge contacts
Clean the print cartridge contacts

CAUTION: Do not clean the print cartridge contacts unless you are having a problem
with print quality and other measures have not been successful. For more information,
see Print quality troubleshooting.

Clean the print cartridge contacts if you get repeated messages on your computer screen
prompting you to check a print cartridge after you already have cleaned or aligned the
print cartridges, or if the Check Print Cartridge light is blinking.
Before cleaning the print cartridge contacts, remove the print cartridge and verify that
nothing is covering the print cartridge contacts, then reinstall the print cartridge. If you
continue to get messages to check the print cartridges, clean the print cartridge contacts.
Make sure you have the following materials available:
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
TIP: Coffee filters are lint-free and work well for cleaning print cartridges.
• Distilled, filtered, or bottled water (tap water might contain contaminants that can
damage the print cartridges).
CAUTION: Do not use platen cleaners or alcohol to clean the print cartridge
contacts. These can damage the print cartridge or the product.

Chapter 10
To clean the print cartridge contacts

1. Turn on the product and open the print cartridge door.
The print carriage moves to the center of the product.
2. Wait until the print carriage is idle and silent, and then unplug the power cord from
the back of the product.
3. Lightly press down on the print cartridge to release it, and then pull it toward you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the HP All-
in-One for more than 30 minutes.
4. Inspect the print cartridge contacts for ink and debris buildup.
5. Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze any
excess water from it.
6. Hold the print cartridge by its sides.
7. Clean only the copper-colored contacts. Allow the print cartridges to dry for
approximately ten minutes before reinserting.
2 Ink nozzles (do not clean)
76 Maintain
8. Hold the print cartridge with the HP logo on top, and insert the print cartridge back
into the slot. Make sure you push the print cartridge in firmly until it snaps into place.
9. Repeat if necessary for the other print cartridge.

10. Gently close the print cartridge door and plug the power cord into the back of the
product.
Related topics
• Clean the area around the ink nozzles

Clean the area around the ink nozzles
If the HP All-in-One is used in a dusty environment, a small amount of debris might
accumulate inside the device. This debris can include dust, hair, carpet, or clothing fibers.
When debris gets on the print cartridges, it can cause ink streaks and smudges on printed
pages. Ink streaking can be corrected by cleaning around the ink nozzles as described
here.
NOTE: Clean the area around the ink nozzles only if you continue to see streaks
and smudges on your printed pages after you have already cleaned the print
cartridges by using the software you installed with the HP All-in-One.

Chapter 10

• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart or
leave fibers.
CAUTION: Do not touch the copper-colored contacts or ink nozzles. Touching

these parts can result in clogs, ink failure, and bad electrical connections.
To clean the area around the ink nozzles

3. Lightly press down on the print cartridge to release it, and then pull it towards you out
of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and clean
each print cartridge one at a time. Do not leave a print cartridge outside the product
for more than 30 minutes.
4. Place the print cartridge on a piece of paper with the ink nozzles facing up.
5. Lightly moisten a clean foam rubber swab with distilled water.
78 Maintain
6. Clean the face and edges around the ink nozzle area with the swab, as shown below.
1 Nozzle plate (do not clean)

2 Face and edges around the ink nozzle area
CAUTION: Do not clean the nozzle plate.
into the slot. Make sure you push the print cartridge in firmly until it snaps into place.

product.
Related topics
Clean the print cartridges

Chapter 10
Remove ink from your skin and clothing

Follow these instructions to remove ink from your skin and clothing:
Surface Remedy
Skin Wash the area with an abrasive soap.
White fabric Wash the fabric in cold water and use chlorine bleach.
Color fabric Wash the fabric in cold water and use sudsy ammonia.
CAUTION: Always use cold water to remove ink from fabric. Warm or hot water can
set the ink into the fabric.
80 Maintain
11 Shop for ink supplies
For a list of print cartridge numbers, see the printed documentation that came with the
HP All-in-One. You can also use the software that came with the HP All-in-One to find
out the reorder number for all the print cartridges. You can order print cartridges online
from the HP Web site. Additionally, you can contact a local HP reseller to find out the
correct print cartridge reorder numbers for your product and purchase print cartridges.
To order genuine HP supplies for the HP All-in-One, go to www.hp.com/buy/supplies. If
prompted, choose your country/region, follow the prompts to select your product, and
then click one of the shopping links on the page.
NOTE: Ordering print cartridges online is not supported in all countries/regions. If it

is not supported in your country/region, contact a local HP reseller for information
about purchasing print cartridges.
To order print cartridges from your desktop

▲ Click the Shop for HP Supplies icon on your desktop to connect to HP SureSupply.
You will see a list of original HP printing supplies that are compatible with your device,
as well as options to conveniently purchase the supplies you need (options vary by
country/region).
If you deleted this icon from your desktop, click the Start menu, point to the HP folder,
then click Shop for Supplies.
To order print cartridges through the HP Photosmart Software

Printer Toolbox.
2. Click the Estimated Ink Levels tab.

3. Click Print Cartridge Ordering Information.
The print cartridge reorder numbers appear.
4. Click Order Online.
HP sends detailed printer information, including model number, serial number, and
ink supply levels, to an authorized online reseller. The supplies you need are
preselected; you can change quantities, add or remove items, and then check out.
Shop for ink supplies
Downloaded from ManualsPrinter.com Manuals Shop for ink supplies 81

Chapter 11
Shop for ink supplies
82 Shop from
Downloaded for inkManualsPrinter.com
supplies Manuals
12 Troubleshooting
• View the Readme file
• Hardware setup troubleshooting
Troubleshooting
• Software installation troubleshooting
• Paper jams
• Print cartridge troubleshooting
• Print quality troubleshooting
• Print troubleshooting
• Copy troubleshooting
• Scan troubleshooting
• Errors
View the Readme file

You might want to refer to the Readme file for information on system requirements and
possible installation problems.
You can access the Readme file by clicking Start, pointing to Programs or All
Programs, pointing to HP, pointing to Deskjet F2200 All-In-One series, and then
clicking Readme.
You can access the Readme file by double-clicking the icon located in the top-level folder
of the HP All-in-One software CD-ROM.
Hardware setup troubleshooting

This section contains hardware troubleshooting information for the product.
Many issues are caused when the product is connected to the computer using a USB
cable before the HP Photosmart software is installed on the computer. If you connected
the product to your computer before the software installation screen prompts you to do
so, you must follow these steps:
Troubleshooting common setup issues

1. Disconnect the USB cable from the computer.
2. Uninstall the software (if you have already installed it).
For more information, see Uninstall and reinstall the software.
3. Restart your computer.
4. Turn off the product, wait one minute, then restart it.
5. Reinstall the HP Photosmart software.
CAUTION: Do not connect the USB cable to the computer until prompted by the
software installation screen.
Downloaded from ManualsPrinter.com Manuals Troubleshooting 83

Chapter 12

• The product will not turn on
• I connected the USB cable, but I am having problems using the HP All-in-One with
my computer
• After setting up the product, it does not print
Troubleshooting
The product will not turn on

Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
• Solution 1: Make sure the power cord is connected
• Solution 2: Press the On button more slowly
Solution 1: Make sure the power cord is connected
Solution:
• Make sure the power cord is firmly connected to both the product and the power
adapter. Plug the power cord into a power outlet, surge protector, or power strip.
1 Power connection
2 Power cord and adapter
• If you are using a power strip, make sure the power strip is on. Or, try plugging
the product directly into a power outlet.
• Test the power outlet to make sure it is working. Plug in an appliance that you
know works, and see if the appliance has power. If not, then there might be a
problem with the power outlet.
• If you plugged the product into a switched outlet, make sure the outlet is switched
on. If it is switched to on but still does not work, then there might be a problem
with the power outlet.
Cause: The product was not properly connected to a power supply.
84 Troubleshooting
If this did not solve the issue, try the next solution.
Solution 2: Press the On button more slowly

Solution: The product might not respond if you press the On button too quickly.
Press the On button once. It might take a few minutes for the product to turn on. If
Troubleshooting
you press the On button again during this time, you might turn the product off.
CAUTION: If the product still does not turn on, it might have a mechanical failure.
Unplug the product from the power outlet.
Contact HP support for service.
Go to: www.hp.com/support. If prompted, choose your country/region, and then
click Contact HP for information on calling for technical support.
Cause: You pressed the On button too quickly.
I connected the USB cable, but I am having problems using the HP All-in-One with
my computer
Solution: You must first install the software that came with the product before
connecting the USB cable. During installation, do not plug in the USB cable until
prompted by the onscreen instructions.
Once you have installed the software, connecting your computer to the product with
a USB cable is straightforward. Simply plug one end of the USB cable into the back
of your computer and the other into the back of the product. You can connect to any
USB port on the back of your computer.
If you installed the software, uninstall it and then reinstall it, connecting the USB cable
only when prompted.
Downloaded from ManualsPrinter.com Manuals Hardware setup troubleshooting 85

Chapter 12
For more information on installing the software and connecting the USB cable, see
the Setup Guide that came with the product.
Cause: The USB cable was connected before the software was installed.
Connecting the USB cable before prompted can cause errors.
After setting up the product, it does not print

Troubleshooting
Solution:
• Look at the On button located on the product. If it is not lit, the product is turned
off. Make sure the power cord is firmly connected to the product and plugged into
a power outlet. Press the On button to turn on the product.
• Make sure the print cartridges are installed.
• Make sure you have paper loaded in the input tray.
• Make sure that the product does not have a paper jam.
• Check that the print carriage is not jammed.
Open the print cartridge door to access the print carriage area. Remove any
objects that are blocking the print carriage, including any packing materials. Turn
the product off and then turn it on again.
• Print a test page to see if the product can print and is communicating with the
computer. For more information, see Print a self-test report.
• Make sure that the print queue is not paused. If it is, choose the appropriate setting
to resume printing. For more information about accessing the print queue, see
the documentation that came with the operating system installed on your
computer.
• Check the USB cable. If you are using an older cable, it might not be working
properly. Try connecting it to another product to see if the USB cable works. If
you experience problems, the USB cable might need to be replaced. Also verify
that the cable does not exceed 3 meters (9.8 feet) in length.
• Make sure your computer is USB ready and that you are using a supported
operating system. For more information, see the Readme file.
• Check the connection from the product to your computer. Verify that the USB
cable is securely plugged into the USB port on the back of the product. Make sure
86 Troubleshooting
the other end of the USB cable is plugged into a USB port on your computer. After
the cable is connected properly, turn the product off and then on again.
Troubleshooting
• If you are connecting the product through a USB hub, make sure the hub is turned
on. If the hub is on, try connecting directly to your computer.
• Check other printers or scanners. You might need to disconnect older products
from your computer.
• Try connecting the USB cable to another USB port on your computer. After you
check the connections, try restarting your computer. Turn the product off and then
on again.
• After you check the connections, try restarting your computer. Turn the product
off and then on again.
• If necessary, remove and then install the software you installed with the product
again. For more information, see Uninstall and reinstall the software.
For more information on setting up the product and connecting it to your computer,
see the Setup Guide that came with the product.
Cause: The product and computer were not communicating with each other.
Software installation troubleshooting

Use this section to solve any problems you might encounter while setting up the
HP Photosmart software.
• When I insert the CD-ROM into my computer’s CD-ROM drive, nothing happens
• The Minimum System Checks screen appears
• A red X appears on the USB connect prompt
• I received a message that an Unknown Error has occurred
• Some of the buttons are missing in the HP Solution Center
Downloaded from ManualsPrinter.com Manuals Software installation troubleshooting 87

Chapter 12
• The registration screen does not appear

• The HP Digital Imaging Monitor does not appear in the system tray
• Uninstall and reinstall the software
When I insert the CD-ROM into my computer’s CD-ROM drive, nothing happens
Solution: If the installation does not run automatically, you can start it manually.
Troubleshooting
To start the installation from a Windows computer

1. From the Windows Start menu, click Run.
2. In the Run dialog box, enter d:\setup.exe, and then click OK.
If your CD-ROM drive is not assigned to drive letter D, enter the appropriate drive
letter.
Cause: The installation failed to run automatically.
The Minimum System Checks screen appears

Solution: Click Details to see what the specific problem is, and then correct the
problem before attempting to install the software.
Cause: Your system did not meet the minimum requirements to install the software.
A red X appears on the USB connect prompt

Solution: Verify that the product is set up properly, and then try to re-establish the
connection.
To retry the USB connection

1. Verify that the USB cable is set up properly as follows:
• Unplug the USB cable and plug it in again or try plugging the USB cable into
a different USB port.
• Do not attach the USB cable to a keyboard.
• Verify that the USB cable is 3 meters (9.8 feet) or less in length.
• If you have several USB devices attached to your computer, you might want
to unplug the other devices during the installation.
2. Unplug the product power cord, and then plug it in again.
88 Troubleshooting
3. Verify that the USB cable and power cord are plugged in.
Troubleshooting
4. Click Retry to retry the connection.
5. Continue with the installation and restart the computer when prompted.
Cause: Normally, a green check appears indicating that the plug and play was
successful. A red X indicates that the plug and play failed.
I received a message that an Unknown Error has occurred

Solution: Try to continue with the installation. If that does not work, stop and then
restart the installation, and follow the directions on the screen. If an error occurs, you
might need to uninstall and then reinstall the software. Do not simply delete the
product application files from your computer. Make sure to remove them properly
using the uninstall utility provided when you installed the software that came with the
product.
For more information, see:
Uninstall and reinstall the software
Cause: The source of the error is unknown.
Some of the buttons are missing in the HP Solution Center

Solution: If the appropriate icons and buttons for your product do not appear in the
HP Solution Center, your installation might not be complete, and you might need to
uninstall and then reinstall the software. Do not simply delete the product application
files from your hard drive. Make sure to remove them properly using the uninstall utility
provided in the HP All-in-One program group.

Chapter 12
Cause: The installation might not be complete.
The registration screen does not appear

Solution: You can access the registration (Sign up now) screen from the Windows
taskbar by clicking Start, pointing to Programs or All Programs, HP, Deskjet F2200
All-In-One series, and then clicking Product Registration.
Troubleshooting
Cause: The registration screen did not launch automatically.
The HP Digital Imaging Monitor does not appear in the system tray
Solution: If the HP Digital Imaging Monitor does not appear in the system tray
(normally located at the lower-right corner of the desktop), start the HP Solution
Center.
If the appropriate icons and buttons for your product do not appear in the HP Solution
Center, your installation might not be complete, and you might need to uninstall and
then reinstall the software. Do not simply delete the product application files from your
hard drive. Make sure to remove them properly using the uninstall utility provided in
the HP All-in-One program group.
Cause: The installation might not be complete.

If your installation is incomplete, or if you connected the USB cable to the computer before
prompted by the software installation screen, you might need to uninstall and then
reinstall the software. Do not simply delete the HP All-in-One application files from your
90 Troubleshooting
computer. Make sure to remove them properly using the uninstall utility provided when
you installed the software that came with the HP All-in-One.
To uninstall from a Windows computer
NOTE: Use this method if Uninstall is not available in the Windows Start menu (click
Programs or All Programs, HP, Deskjet F2200 All-In-One series, Uninstall).
Troubleshooting
1. Open the Windows control panel and double-click Add or Remove Programs.
NOTE: The procedure to open the control panel varies by operating system. If
you are not sure how to do this, see the Windows Help.
2. Select HP Deskjet All-In-One Driver Software, and then click Change/Remove.

Follow the onscreen instructions.
3. Disconnect the product from your computer.
NOTE: It is important that you disconnect the product before restarting your
computer. Do not connect the product to your computer until after you have
reinstalled the software.
5. Insert the product CD-ROM into your computer’s CD-ROM drive and then start the
Setup program.
6. Follow the onscreen instructions and the instructions provided in the Setup Guide that
came with the product.
When the software installation is complete, the HP Digital Imaging Monitor icon appears
in the Windows system tray.
To verify that the software is properly installed, double-click the HP Solution Center icon
on the desktop. If the HP Solution Center shows the essential icons (Scan Picture and
Scan Document), the software has been properly installed.

Chapter 12
Paper jams
To help avoid paper jams, follow these guidelines:
• Remove printed papers from the output tray frequently.
• Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag.
• Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn.
• Do not combine different paper types and paper sizes in the input tray; the entire stack
Troubleshooting
of paper in the input tray must be the same size and type.
• Adjust the paper-width guide in the input tray to fit snugly against all paper. Make sure
the paper-width guide does not bend the paper in the input tray.
• Do not force paper too far forward in the input tray.
• Use paper types that are recommended for the product.
For more information, see the following topics:
• Clear paper jams
• Information on paper
Clear paper jams

Solution: Clear the paper jam through the rear access door.
To clear a paper jam from the rear access door

1. Press in the tab on the left side of the rear access door to release the door.
Remove the door by pulling it away from the product.
CAUTION: Trying to clear a paper jam from the front of the product can
damage the print mechanism. Always access and clear paper jams through
the rear access door.
2. Gently pull the paper out of the rollers.
CAUTION: If the paper tears when you are removing it from the rollers, check
the rollers and wheels for torn pieces of paper that might be remaining inside
the product. If you do not remove all the pieces of paper from the product,
more paper jams are likely to occur.
92 Troubleshooting
3. Replace the rear access door. Gently push the door forward until it snaps into
place.
Troubleshooting
4. Press any button on the control panel to continue the current job.
Cause: Paper had jammed in the product.
Information on paper
The HP All-in-One is designed to work well with most paper types. Test a variety of paper
types before buying a large quantity. Find a paper type that works well and is easy to
purchase. HP Premium papers are designed for the best quality results. In addition, follow
these tips:
• Do not use paper that is too thin, that has a slick texture, or that stretches easily. It
can feed incorrectly through the paper path, causing paper jams.
• Store photo media in its original packaging inside a resealable plastic bag on a flat
surface in a cool, dry place. When you are ready to print, remove only the paper you
plan to use immediately. When you have finished printing, return any unused photo
paper to the plastic bag.
• Do not leave unused photo paper in the input tray. The paper might start to curl, which
might reduce the quality of your printouts. Curled paper can also cause paper jams.
• Always hold photo paper by the edges. Fingerprints on photo paper can reduce print
quality.
• Do not use paper that is heavily textured. It can cause graphics or text to print
improperly.
• Do not combine different paper types and paper sizes in the input tray; the entire stack
of paper in the input tray must be the same size and type.
• Store printed photos under glass or in a storage book to prevent bleeding over time
from high humidity. Use HP Premium Plus photo paper for maximum performance.
Print cartridge troubleshooting

If you are experiencing problems with printing, you might have a problem with one of the
print cartridges. If you receive an error message about the print cartridges, see Print
cartridge messages for more information.
Try the following:
• Information on print cartridges
• Resolving print cartridge problems
• Resolving print cartridge error messages
Downloaded from ManualsPrinter.com Manuals Print cartridge troubleshooting 93

Chapter 12
Information on print cartridges

For best results, use HP print cartridges. The following tips help maintain HP print
cartridges and ensure consistent print quality.
• Keep all print cartridges in the original sealed packages until they are needed.
• Store print cartridges at room temperature (15.6°-26.6° C or 60°-78° F).
• Do not reattach the protective tape once it has been removed from the print cartridge.
Troubleshooting
Reattaching the plastic tape might damage the print cartridge. Place the print cartridge
in the product immediately after removing the plastic tape. If this is not possible, store
it in a print cartridge protector or airtight plastic container.
• HP recommends that you do not remove the print cartridges from the product until
you have replacement print cartridges available to install.
• Turn off the product from the control panel. Do not turn off the product by turning off
a power strip or unplugging the power cord from the product. If you improperly turn
off the product, the print carriage does not return to the correct position and the print
cartridges can dry out.
• Do not open the print cartridge door unless necessary. This exposes the print
cartridges to air, which reduces the life of the print cartridges.
NOTE: If you leave the print cartridge door open for a long period of time, the
product will recap the print cartridges to protect them from exposure to air.
• It might be necessary to clean the print cartridges when you notice a significant
decrease in print quality.
TIP: You might notice a decrease in print quality if the print cartridges have not
been used for a long time.
• Do not clean the print cartridges unnecessarily. This wastes ink and shortens the life
of the cartridges.
• Handle print cartridges carefully. Dropping, jarring, or rough handling during
installation can cause temporary printing problems. If print quality is poor right after
cartridge installation, allow half an hour for the print cartridge to recover.
Print cartridge troubleshooting
94 Troubleshooting
Resolving print cartridge problems
Many problems can be resolved with the following procedures. If you receive a specific
error message about the print cartridges, see Print cartridge messages for more
information.
To troubleshoot the print cartridges

1. Remove and reinstall the print cartridges.
Troubleshooting
For more information, see Replace the print cartridges.
NOTE: Make sure the plastic tape has been removed. If it is still covering the ink
nozzles, gently remove the plastic tape by using the pink pull tab.
2. If print quality is suffering, check the estimated ink levels.

For more information, see Check the estimated ink levels.
3. Print a self-test report and review the test patterns.
For more information, see Print a self-test report.
4. Clean the print cartridges:
• First, try cleaning the print cartridges from the HP Photosmart Software. For more
information, see Clean the print cartridges.
CAUTION: Performing this procedure unnecessarily can waste ink and

shorten the life of the cartridges.
• If cleaning the print cartridges from the software did not help, you can try cleaning
the print cartridge contacts. For more information, see Clean the print cartridge
contacts.
5. If none of the previous procedures resolved the problem, replace the print cartridges.
Resolving print cartridge error messages

After you install a print cartridge, one or both of the print cartridge status lights begin to
blink. The printer will not print. One of the following messages may appear on your
computer screen:
Print Cartridge Problem
Incorrect Print Cartridge(s)
Incorrectly Installed Cartridge(s)
Print Cartridge(s) Missing
Work through the following sections in order. When the print cartridge light stops blinking,
you have solved the problem.

Chapter 12
NOTE: In the procedures below, the problem cartridge is identified by the blinking
light. The light on the left blinks when the tri-color print cartridge (on the left) is the
problem, the light on the right blinks when the black or photo cartridge (on the right)
is the problem, and both lights blink when both cartridges are the problem.
• Solution 1: Remove and reinstall the print cartridges

• Solution 2: Clean the print cartridge contacts
Troubleshooting
• Solution 3: Print in ink-backup mode
Solution 1: Remove and reinstall the print cartridges

Solution: The print cartridge may not have full electrical contact with the printer.
Removing and reinstalling the cartridge may help.
NOTE: HP cannot guarantee the quality of remanufactured or refilled cartridges.
To verify and install the correct print cartridges

1. Make sure the product is on. Press the On button if it is not lit.
2. Open the print cartridge door, and then wait until the print carriage is idle and
silent.
3. Press down lightly on the end of the problem cartridge to release it.
4. Slide the cartridge out and inspect it:
CAUTION: Do not touch the copper electrical contacts or the ink nozzles.
• Check the electrical contacts for debris.
• Make sure all the clear nozzle protective tape has been removed.
CAUTION: Do not attempt to remove the copper electrical strip!

5. Read the selection number on the print cartridge label and make sure it is
compatible with the product. Compatible print cartridges are listed in the printed
documentation that came with the product.
1 Selection number
96 Troubleshooting
6. If the print cartridge has the wrong selection number, install a new print cartridge.
Troubleshooting
Solution 2: Clean the print cartridge contacts
Solution: If the print cartridge selection number is correct and the previous solution
did not resolve the problem, try cleaning the print cartridge. For more information, see
Clean the print cartridge contacts.
If the print cartridge status light continues to flash after cleaning the print cartridge,
replace the print cartridge. For more information, see Replace the print cartridges.
Solution 3: Print in ink-backup mode

Solution: If you do not have a replacement print cartridge, you can still print in ink
backup mode. Remove the problem cartridge and print with the remaining cartridge.
Use ink-backup mode

Chapter 12
Print quality troubleshooting

If you are having problems with print quality, try the solutions in this section and observe
the following guidelines.
To troubleshoot print quality issues

1. Check the print cartridges.
Troubleshooting
HP recommends that you use genuine HP print cartridges. Genuine HP print

cartridges are designed and tested with HP printers to help you easily produce great
results, time after time.
NOTE: HP cannot guarantee the quality or reliability of non-HP supplies. Printer

service or repairs required as a result of using a non-HP supply will not be covered
under warranty.
If you believe you purchased genuine HP ink cartridges, go to:
www.hp.com/go/anticounterfeit

2. Check the ink levels.
If you have installed a refilled or remanufactured print cartridge, or a cartridge that
has been used in another printer, the ink level indicator will be inaccurate or
unavailable. The ink levels provided are an estimate. When print cartridges are truly
low on ink, printouts will be faded or streaked. As long as print quality is acceptable,
there is no reason to replace print cartridges. Low ink warnings are provided for
planning purposes only.
For more information, see Check the estimated ink levels.
3. Make sure you turn off the product by pressing the On button.
CAUTION: Do not turn off the product by turning off a power strip or unplugging
the power cord from it. If you improperly turn off the product, the print carriage
does not return to the correct position and the print cartridges can dry out.
4. To achieve the best print quality, HP recommends using HP papers that are
specifically designed for the type of project you are printing along with genuine HP
ink. HP papers and HP ink are specifically designed to work well together to provide
high-quality output.
5. Check the product settings to make sure that the print mode and paper selection is
correct for the paper and the task.
For more information, see Set the paper type for printing and Choose papers for
printing and copying.
6. If the cartridges are genuine HP and the product is not in backup mode, print a self-
test report to determine if the product and ink supplies are operating correctly.
This will use one sheet of plain paper and a very small amount of ink.
98 Troubleshooting
7. Evaluate the self-test report.
If the self-test report shows a defect, try the following:
• Clean the print cartridges automatically. For more information, see Clean the print
cartridges.
• If you are missing lines when you print, clean the electrical contacts. For more
information, see Clean the print cartridge contacts.
• Replace the print cartridge. For more information, see Replace the print
Troubleshooting
cartridges.
8. If the self-test report does not show a problem, investigate other causes, such as the
image file or software program.
For additional print cartridge troubleshooting, visit the HP Web site at www.hp.com/
support.
• Wrong, inaccurate, or bleeding colors
• Ink is not filling the text or graphics completely
• The printout has a horizontal band of distortion near the bottom of a borderless print
• Printouts have horizontal streaks or lines
• Printouts are faded or have dull colors
• Printouts seem blurry or fuzzy
• Printouts have vertical streaks
• Printouts are slanted or skewed
• Ink streaks on the back of the paper
• Paper is not picked up from the input tray
• The text edges are jagged
Wrong, inaccurate, or bleeding colors

If your printout has one of the following print quality problems, try the solutions in this
section for help.
• Colors look different than what you expected.
For example, the colors in your graphic or photo look one way on your computer
screen but print out differently, or magenta was replaced with cyan in your printout.
• Colors run into each other, or look like they are smeared on the page. The edges
might have a feathering appearance instead of being sharp and defined.
Try the following solutions if the colors appear wrong, inaccurate, or bleed into each other.
• Solution 1: HP recommends using genuine HP print cartridges
• Solution 2: Check the paper loaded in the input tray
• Solution 3: Check the paper type
• Solution 4: Check to see if the product is in ink-backup mode
• Solution 5: Check the print settings
• Solution 6: Clean the print cartridges
Solution 1: HP recommends using genuine HP print cartridges

Solution: Check to see if your print cartridges are genuine HP print cartridges.
Downloaded from ManualsPrinter.com Manuals Print quality troubleshooting 99

Chapter 12


under warranty.
Troubleshooting
If you believe you purchased genuine HP print cartridges, go to:

Cause: Non-HP ink was being used.

Solution 2: Check the paper loaded in the input tray

Solution: Make sure the paper is loaded correctly and that it is not wrinkled or too
thick.
• Load paper with the side you want to print on facing down. For example, if you
are loading glossy photo paper, load the paper with the glossy side down.
• If the paper is too close to the print cartridge during printing, the ink might be
smeared. This can happen if the paper is raised, wrinkled, or very thick, such as
a mailing envelope. Make sure the paper lays flat in the input tray and is not
wrinkled.
• Load paper
Cause: The paper was loaded incorrectly, or it was wrinkled or too thick.
Solution 3: Check the paper type

Solution: HP recommends that you use HP Premium Papers or any other paper
type that is appropriate for the product.
Always make sure the paper you are printing on is flat. For best results when printing
images, use HP Premium Plus Photo Paper.
Store photo media in its original packaging inside a resealable plastic bag on a flat
paper to the plastic bag. This will prevent the photo paper from curling.
NOTE: There is no problem with the ink supplies and replacing the print
cartridges is unnecessary.
100 Troubleshooting
Cause: The wrong kind of paper was loaded in the input tray.
Troubleshooting
Solution 4: Check to see if the product is in ink-backup mode
Solution: Check to see if the the product is printing in ink-backup mode, with only
one print cartridge installed.
If the product is in ink-backup mode, text and photo quality will differ from those printed
when using both print cartridges.
If you are satisfied with the print quality, continue printing in ink-backup mode. Or,
replace the missing print cartridge.
• Use ink-backup mode
Cause: A print cartridge was missing and the product was printing in ink-backup
mode.
Solution 5: Check the print settings

Solution: Check the print settings.
• Check the print settings to see if the color settings are incorrect.
For example, check to see if the document is set to print in grayscale. Or, check
to see if advanced color settings such as saturation, brightness, or color tone, are
set to modify the appearance of colors.
• Check the print quality setting and make sure it matches the type of paper loaded
in the product.
You might need to choose a lower print quality setting, if colors are running into
each other. Or, choose a higher setting if you are printing a high-quality photo,
and then make sure photo paper such as HP Premium Photo Papers, is loaded
in the input tray.
NOTE: On some computer screens, colors might appear differently than they do
when printed on paper. In this case, there is nothing wrong with the product, print
settings, or print cartridges. No further troubleshooting is required.

Cause: The print settings were set incorrectly.

Chapter 12
Solution 6: Clean the print cartridges

Solution: Print a self-test report to determine if there is a problem with the print
cartridges. If the self-test report shows a problem, clean the print cartridges. If the
Troubleshooting
problem persists, you might need to replace the print cartridges.

For more information on print cartridges, see Print cartridge troubleshooting.
Cause: The print cartridges need to be cleaned.
Ink is not filling the text or graphics completely

Try the following solutions if the ink is not filling the text or image completely so that it
appears that parts are missing or blank.
• Solution 1: HP recommends using genuine HP print cartridges
Solution 1: HP recommends using genuine HP print cartridges

Solution: Check to see if your print cartridges are genuine HP print cartridges.

under warranty.
Cause: Non-HP ink was being used.


• Check the paper type setting to make sure it matches the type of paper loaded in
the input tray.
• Check the quality setting. Use a higher quality setting to increase the amount of
ink used for printing.
102 Troubleshooting
Cause: The paper type or print quality settings were incorrectly.
Troubleshooting



Solution: Print a self-test report to determine if there is a problem with the print
cartridges. If the self-test report shows a problem, clean the print cartridges. If the
problem persists, you might need to replace the print cartridges.
Cause: The print cartridges need to be cleaned.
The printout has a horizontal band of distortion near the bottom of a borderless
print
Try the following solutions if your borderless print has a blurry band or line on the bottom
of it.

Chapter 12
NOTE: There is no problem with the ink supplies and replacing the print cartridges
is unnecessary.

• Solution 2: Check the print quality setting
• Solution 3: Rotate the image
Troubleshooting


Solution 2: Check the print quality setting

Solution: Check the quality setting. Use a higher quality setting to increase the
amount of ink used for printing.
using Maximum dpi.

Cause: The print quality setting was set too low.
104 Troubleshooting
Solution 3: Rotate the image
Solution: If the problem persists, use the software you installed with the product or
another software application to rotate your image 180 degrees so that the light blue,
gray, or brown hues in your image do not print at the bottom of the page.
Change the page orientation
Troubleshooting
Cause: The photo image had light blue, gray, or brown hues that print near the
bottom of the page.
Printouts have horizontal streaks or lines

Try the following solutions if your printout has lines, streaks, or marks on it that run side-
to-side across the width of the page.
• Solution 1: Make sure the paper is loaded correctly
• Solution 2: Check the print quality setting
• Solution 3: If the print cartridge was dropped, wait for it to recover
• Solution 4: Clean the print cartridge nozzles
Solution 1: Make sure the paper is loaded correctly

Solution: Make sure the paper is loaded correctly.
Cause: The paper was not feeding properly or was not loaded correctly.
Solution 2: Check the print quality setting

Solution: Check the quality setting. Use a higher quality setting to increase the
amount of ink used for printing.
using Maximum dpi.

Cause: The print quality setting was set too low.

Chapter 12
Solution 3: If the print cartridge was dropped, wait for it to recover

Solution: Allow 30 minutes for the print cartridge to recover.
Cause: A tri-color or photo print cartridge was jarred or handled roughly during
installation.
Troubleshooting
Solution 4: Clean the print cartridge nozzles

Solution: Check the print cartridges. If it looks as though there are fibers or dust
around the ink nozzles, clean the ink nozzle area of the print cartridge.
Clean the area around the ink nozzles
Cause: The print cartridge nozzles needed to be cleaned.

Solution: Check the estimated ink levels remaining in the print cartridges.
NOTE: Ink level warnings and indicators provide estimates for planning
purposes only. When you receive a low-ink warning message, consider having a
replacement cartridge available to avoid possible printing delays. You do not need
to replace the print cartridges until print quality becomes unacceptable.
If there is ink remaining in the print cartridges, but you are still noticing a problem,
print a self-test report to determine if there is a problem with the print cartridges. If the
self-test report shows a problem, clean the print cartridges. If the problem persists,
you might need to replace the print cartridges.

Cause: The print cartridges needed to be cleaned or there was insufficient ink.
Printouts are faded or have dull colors

Try the following solutions if the colors in your printout are not as bright and intense as
you expected.
• Solution 3: If you are making a copy, place a protective sheet on the glass
• Solution 4: Clean the glass
106 Troubleshooting
the input tray.
Troubleshooting
Cause: The paper type or print quality settings were set incorrectly.


Solution 3: If you are making a copy, place a protective sheet on the glass
Solution: If you are making a copy, try placing one or more clear plastic sheet
protectors directly on the glass, and then place the original print side down on top of
the sheet protectors.
Cause: The quality of the original was poor.

Chapter 12
Solution 4: Clean the glass

Solution: Clean the glass and lid backing.
• Clean the glass
Cause: Debris might be stuck on the glass or on the back of the document lid; this
Troubleshooting
causes poor copy quality and slows down processing.



Printouts seem blurry or fuzzy

Try the following solutions if your printout is smudged or unclear.
NOTE: There is no problem with the ink supplies and replacing the print cartridges
is unnecessary.
TIP: After reviewing the solutions in this section, you can go to HP's support Web
site to see if there is additional troubleshooting help. For more information, go to:
www.hp.com/support.

• Solution 2: Check the resolution of the image
108 Troubleshooting
the input tray.
Troubleshooting
Cause: The paper type or print quality settings were set incorrectly.
Solution 2: Check the resolution of the image

Solution: Check the resolution of the image. If you are printing a photo or graphic,
and the resolution is too low, it will be blurry or fuzzy when printed.
If a digital photo or rasterized graphic has been resized, it can be blurry or fuzzy when
printed.
Cause: The resolution of the image was low.
Printouts have vertical streaks

Refer to this section if your printout has a lines, streaks, or marks on it that run up-
and-down or lengthwise down the page.


Chapter 12
Printouts are slanted or skewed

Try the following solutions if your printout does not appear straight on the page.
• Solution 1: Make sure the paper is loaded correctly
Troubleshooting
• Solution 2: Make sure only one type of paper is loaded

• Solution 3: Check the rear access door
Solution 1: Make sure the paper is loaded correctly

Solution: Make sure the paper is loaded correctly.
Cause: The paper was not feeding properly or was not loaded correctly.
Solution 2: Make sure only one type of paper is loaded

Solution: Load only one type of paper at a time.
Cause: More than one type of paper was loaded in the input tray.
Solution 3: Check the rear access door

Solution: Make sure the rear access door is securely installed.
Cause: The rear access door was not securely installed.
Ink streaks on the back of the paper

Try the following solutions if there is smeared ink on the back of your printout.
• Solution 1: Print on a page of plain paper
• Solution 2: Wait while the ink dries
Solution 1: Print on a page of plain paper

Solution: Print one or several pages of plain paper to soak up any excess ink in
the product.
To remove excess ink using plain paper

1. Load several sheets of plain paper in the input tray.
2. Wait five minutes.
110 Troubleshooting
3. Print a document with little or no text.
4. Check the back of the paper for ink. If there is still ink on the back of the paper,
try printing on another page of plain paper.
Cause: Ink accumulated inside the product, where the back of the paper rests
during printing.
Troubleshooting
Solution 2: Wait while the ink dries
Solution: Wait at least thirty minutes for the ink inside the product to dry, then try
the print job again.
Cause: The excess ink in the product needed to dry out.
Paper is not picked up from the input tray
Solution:
Do one of the following:
• If the product is out of paper or there are only a few sheets remaining, load more
paper in the input tray.
• If there is paper in the input tray:
• Remove the stack of paper from the input tray and verify that all the paper in
the input tray is the same size and type.
• Replace any paper that is ripped, dusty, wrinkled, or bent.
If the paper is curled, uncurl the paper by gently bending it in the opposite
direction of the curl or replace the paper.
• Tap the stack of paper on a flat surface to align the edges.
• Verify that the stack of paper contains between 10 and 25 sheets of paper.
• Reload the paper into the input tray.
Follow the prompts on the display to continue.
Cause: There was not enough paper in the input tray.
The text edges are jagged

Try the following solutions if the text in your printouts is not sharp and the edges are
rough.
Solution: Use TrueType or OpenType fonts to ensure that the product is able to
print smooth fonts. When selecting a font, look for the TrueType or OpenType icon.
Some software applications offer custom fonts that have jagged edges when enlarged
or printed. Also, if you want to print bitmapped text, it might have jagged edges when
enlarged or printed.

Chapter 12
Cause: The font was a custom size.
Print troubleshooting
Use this section to solve these printing problems:
• Envelopes print incorrectly
Troubleshooting
• Borderless printing produces unexpected results

• The product is not responding
• The product prints meaningless characters
• Nothing happens when I try to print
• The pages in my document came out in the wrong order
• The margins are not printing as expected
• Text or graphics are cut off at the edge of the page
• A blank page came out while printing
• Ink is spraying the inside of the HP All-in-One when I print a photo
Envelopes print incorrectly

• Solution 1: Reload the envelopes in the input tray
• Solution 2: Load a different type of envelope
Solution 1: Reload the envelopes in the input tray

Solution: Remove all paper from the input tray. Load a stack of envelopes in the
input tray, with the envelope flaps facing up and on the left.
NOTE: To avoid paper jams, tuck the flaps inside the envelopes.
Cause: A stack of envelopes was loaded incorrectly.

Solution 2: Load a different type of envelope

Solution: Do not use shiny or embossed envelopes or envelopes that have clasps
or windows.
112 Troubleshooting
Cause: The wrong type of envelope was loaded.
Borderless printing produces unexpected results

Troubleshooting
• Solution 1: Print from the HP Photosmart Software
• Solution 2: Use the appropriate media
Solution 1: Print from the HP Photosmart Software

Solution: Try printing the image from the photo imaging software that came with
the product.
Cause: Printing a borderless image from a non-HP software application produced
unexpected results.
Solution 2: Use the appropriate media

Solution: To print a borderless image, use 10 x 15 cm (4 x 6 inch) HP Premium
Plus Photo Papers with a tear-off tab. When you remove the tear-off tab, the printed
image is borderless and extends to the edges of the paper.
Print a borderless image
Cause: Use of inappropriate media.
The product is not responding

• Solution 1: Wait for the product to finish other tasks
• Solution 2: Check for a paper jam
• Solution 3: Load more paper in the input tray
• Solution 4: Check for a print carriage stall
• Solution 5: Check the cable connections to the product
• Solution 6: Make sure that the product is turned on
• Solution 7: Restart the product
• Solution 8: Check the print driver status
• Solution 9: Check the print queue for canceled jobs
Downloaded from ManualsPrinter.com Manuals Print troubleshooting 113

Chapter 12
Solution 1: Wait for the product to finish other tasks

Solution: If the product is performing another task such as copying or scanning,
your print job will be delayed until the product completes the current task.
Some documents take a long time to print. If nothing has printed several minutes after
you sent a print job to the product, check your computer to see if there are any
messages.
Troubleshooting
Cause: The product was busy with another task.

Solution 2: Check for a paper jam

Solution: Clear the paper jam.
Clear paper jams
Cause: The product had a paper jam.
Solution 3: Load more paper in the input tray

Solution: Load paper in the input tray.
Cause: The product was out of paper.
Solution 4: Check for a print carriage stall

Solution: Turn off the product, open the print cartridge door, and remove any
objects that are blocking the print carriage (including any packing materials), and then
turn on the product.

The print carriage is stalled
114 Troubleshooting
Cause: The print carriage has stalled.
Solution 5: Check the cable connections to the product

Solution: If the product is not properly connected to the computer, communication
Troubleshooting
errors can occur. Try the following:
If the connections are secure, and nothing has printed several minutes after you sent
a print job to the product, check the status of the product. In the HP Photosmart
Software, click Settings, and then click Status.
Cause: The computer was not communicating with the product.
Solution 6: Make sure that the product is turned on

Solution: Look at the On button located on the product. If it is not lit, the product is
turned off. Make sure the power cord is firmly connected to the product and plugged
into a power outlet. Press the On button to turn on the product.
Cause: The product was turned off.
Solution 7: Restart the product

Solution: Turn off the product, and then unplug the power cord. Plug the power
cord back in, and then press the On button to turn on the product.

Chapter 12
Cause: The product experienced an error.

Solution 8: Check the print driver status

Solution: The printer driver status might have changed to either offline or stop
Troubleshooting
printing.
To check the printer driver status

1. In the HP Solution Center, click the Settings tab.
2. Click Status.
If the status is Offline or Stop printing, change the status to Ready.
Cause: The status of the printer driver has changed.
Solution 9: Check the print queue for canceled jobs

Solution: A print job might remain in the queue after it has been cancelled. The
cancelled print job jams the queue and prevents the next print job from printing.
From your computer, open the printer folder and see if the cancelled job remains in
the print queue. Try to delete the job from the queue. If the print job remains in the
queue, try one or both of the following:
• Disconnect the USB cable from the product, restart the computer, and then
reconnect the USB cable to the product.
• Shut down the product, restart the computer, and then restart the product.
Cause: A deleted print job was still in the queue.
The product prints meaningless characters

• Solution 1: Restart the product and your computer
• Solution 2: Try printing another document
Solution 1: Restart the product and your computer

Solution: Turn off the product and your computer for 60 seconds, then turn them
both on and try printing again.
Cause: The memory in the product was full.
116 Troubleshooting
Solution 2: Try printing another document
Solution: Try printing another document from the same software application. If this
works, then try printing a previously saved version of the document that is not corrupt.
Cause: The document was corrupt.
Troubleshooting
Nothing happens when I try to print
• Solution 3: Make sure that the product is the selected printer
• Solution 4: Check the cable connections to the product
• Solution 7: Check for a print carriage stall


Solution: If the product is performing another task such as copying or scanning,
your print job will be delayed until the product completes the current task.
Some documents take a long time to print. If nothing has printed several minutes after
you sent a print job to the product, check the product display to see if there are any
messages.
Solution 3: Make sure that the product is the selected printer

Solution: Make sure the product is the selected printer in your software application.
TIP: You can set the product as the default printer to ensure that the printer is
automatically selected when you select Print in the File menu of your different
software applications.
Cause: The product was not the selected printer.

Chapter 12
Solution 4: Check the cable connections to the product

errors can occur.
Troubleshooting
If the connections are secure, and nothing has printed several minutes after you sent
a print job to the product, check the status of the product. In the HP Photosmart
Software, click Settings, and then click Status.

Solution: Load paper in the input tray.
Cause: The product was out of paper.
118 Troubleshooting
Clear paper jams
Troubleshooting
Solution 7: Check for a print carriage stall

Cause: The print carriage has stalled.
The pages in my document came out in the wrong order

Solution: Print the document in reverse order. When the document finishes
printing, the pages will be in correct order.
Print a multiple-page document in reverse order
Cause: The print settings were set to print the first page of your document first.
Because of the way the paper feeds through the product, this means the first page
will be print side up at the bottom of the stack.
The margins are not printing as expected

• Solution 1: Set the correct margins in your software application
• Solution 2: Make sure that the paper size setting is correct

Chapter 12
• Solution 3: Check the paper guide position

• Solution 4: Make sure the stack of envelopes is loaded correctly
Solution 1: Set the correct margins in your software application

Solution: Check the printer margins.
Make sure the margin settings for the document do not exceed the printable area of
Troubleshooting
the product.
To check your margin settings

1. Preview your print job before sending it to the product.
In most software applications, click the File menu, and then click Print Preview.
2. Check the margins.
The product uses the margins you have set in your software application, as long
as they are greater than the minimum margins the product supports. For more
information about setting margins in your software application, see the
documentation that came with the software.
3. Cancel the print job if the margins are not satisfactory, and then adjust the margins
in your software application.
Cause: The margins were not set correctly in your software application.
Solution 2: Make sure that the paper size setting is correct

Solution: Verify that you have selected the proper paper size setting for your
project. Make sure that you have loaded the correct paper size in the input tray.
For example, in some countries/regions you may need to specify A4 as the paper
size if A (letter) is the default value.
Set the paper type for printing
Cause: The paper size setting was not set correctly for the project you were printing.
Solution 3: Check the paper guide position

Solution: Remove the stack of paper from the input tray, and then reload the paper.
Make sure that you slide the paper-width guide to the right until it stops at the edge
of the paper.
Load paper
Cause: The paper guides are not positioned correctly.
120 Troubleshooting
Solution 4: Make sure the stack of envelopes is loaded correctly
Solution: Remove all paper from the input tray. Load a stack of envelopes in the
input tray, with the envelope flaps facing up and on the left.
NOTE: To avoid paper jams, tuck the flaps inside the envelopes.
Troubleshooting
Load envelopes
Cause: A stack of envelopes was loaded incorrectly.
Text or graphics are cut off at the edge of the page

• Solution 1: Check the margins in your software application
• Solution 2: Make sure the document can fit on a supported paper size
• Solution 3: Remove and reload the paper in the input tray
Solution 1: Check the margins in your software application

Solution: Make sure the margin settings for the document do not exceed the
printable area of the product.
To check your margin settings

2. Check the margins.
The product uses the margins you have set in your software application, as long
as they are greater than the minimum margins the product supports. For more
information about setting margins in your software application, see the
documentation that came with the software.
3. Cancel the print job if the margins are not satisfactory, and then adjust the margins
in your software application.
Cause: The margins are not set correctly in your software application.

Chapter 12
Solution 2: Make sure the document can fit on a supported paper size
Solution: Make sure the layout of the document you are trying to print fits on a paper
size supported by the product.
To preview the print layout

1. Load the correct paper size into the input tray.
Troubleshooting

3. Check the graphics in the document to make sure that the current size fits within
the printable area of the product.
4. Cancel the print job if the graphics do not fit in the printable area of the page.
TIP: Some software applications allow you to scale the document to fit the paper
size currently selected. Additionally, you can scale the size of a document from
the print Properties dialog box.
Cause: The size of the document you are printing is larger than the paper loaded
in the input tray.
Solution 3: Remove and reload the paper in the input tray

Solution: If the paper is misfeeding, it could cause parts of the document to cut off.
Remove the stack of paper from the input tray, and then reload the paper. Make sure
that you slide the paper-width guide inward until it stops at the edge of the paper.
Cause: The paper is loaded incorrectly.
A blank page came out while printing

• Solution 1: Check the ink levels in the print cartridges
• Solution 2: Check for blank pages at the end of the document
• Solution 4: Check the print cartridges for protective tape
Solution 1: Check the ink levels in the print cartridges

122 Troubleshooting
Troubleshooting
Cause: If you are printing black text, and a blank page comes out of the product,
the black print cartridge might be empty.
Solution 2: Check for blank pages at the end of the document

Solution: Open the document file in your software application and remove any extra
pages or lines at the end of the document.
Cause: The document you are printing contains an additional blank page.

Solution: If the product has only a few sheets remaining, load more paper in the
input tray. If there is plenty of paper in the input tray, remove the paper, tap the stack
of paper against a flat surface, and reload the paper into the input tray.
Cause: The product picked up two sheets of paper.
Solution 4: Check the print cartridges for protective tape

Solution: Check each print cartridge. The tape might have been removed from the
copper-colored contacts, but still might cover the ink nozzles. If the tape is still

Chapter 12
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not
touch the ink nozzles or the copper-colored contacts.
Troubleshooting

Cause: The protective plastic tape was only partially removed from the print
cartridge.
Ink is spraying the inside of the HP All-in-One when I print a photo

Solution: Make sure you load photo paper in the input tray before you print a
borderless print job.
Cause: The borderless print settings require photo paper to be loaded in the input
tray. You are using the wrong paper type.
Copy troubleshooting
Use this section to solve these copy problems:
• Nothing happens when I try to copy
• Parts of the original do not appear or are cut off
• The printout appears enlarged on the page
• The printout is blank
• A borderless copy has white space around the edges
124 Troubleshooting
Nothing happens when I try to copy
• Solution 2: Make sure that the original is placed correctly on the glass
Troubleshooting
• Solution 4: Make sure the paper loaded is recognized by the product

Solution 2: Make sure that the original is placed correctly on the glass
Solution: Place your original with the side you want to copy or scan face down on
the left front corner of the glass.
Cause: The original was placed incorrectly on the glass.


Solution: Check the On light. If it is blinking, the product is busy.
If the product is performing another task such as printing or scanning, your copy job
will be delayed until the product completes the current task.
Downloaded from ManualsPrinter.com Manuals Copy troubleshooting 125

Chapter 12
Solution 4: Make sure the paper loaded is recognized by the product

Solution: Do not use the product to copy onto envelopes or other papers the
product does not support.
Troubleshooting
Related topics
Recommended papers for printing and copying
Cause: The product did not recognize the inserted paper type.

Clear paper jams
Parts of the original do not appear or are cut off

• Solution 1: Place the original correctly on the glass
• Solution 2: Clean the scanner glass
Solution 1: Place the original correctly on the glass

126 Troubleshooting
Solution 2: Clean the scanner glass

Solution: Clean the scanner glass and make sure that there are no foreign
materials adhering to it.
Troubleshooting
For more information, see Clean the glass.
Cause: The scanner glass was dirty, causing the product to include an area in the
copy that was larger than the document.
The printout appears enlarged on the page

Solution: Ensure that your Copy settings are chosen correctly. If the problem
persists, debris might be stuck on the glass or on the back of the document lid. This
can cause the product to detect only a portion of the image. Turn off the product,
unplug the power cord, and use a soft cloth to wipe the glass and the back of the
document lid.
• Clean the glass
Cause: The product detected only a portion of the image due to dust or debris on
the glass.
The printout is blank

• Solution 1: Place the original correctly on the glass
• Solution 2: Check the ink levels in the print cartridges
Solution 1: Place the original correctly on the glass

Downloaded from ManualsPrinter.com Manuals Copy troubleshooting 127

Chapter 12

Solution 2: Check the ink levels in the print cartridges

Troubleshooting
A borderless copy has white space around the edges

• Solution 1: Resize the image
• Solution 2: Use photo paper
Solution 1: Resize the image

Solution: When you make a borderless copy of a very small original, the product
enlarges the original up to a maximum percentage. This might leave white space
around the edges. (The maximum percentage varies by model.)
Depending on the size of the borderless copy you are trying to make, the minimum
size of the original varies. For example, you cannot enlarge a passport photo to create
a letter-size borderless copy.
If you want to make a borderless copy of a very small original, scan the original into
the computer, resize the image, and then print a borderless copy of the enlarged
image.
Cause: You were trying to make a borderless copy of a very small original.
Solution 2: Use photo paper

Solution: Use photo paper with a tear-off tab to make borderless copies.
128 Troubleshooting
Cause: You were trying to make a borderless copy without using photo paper.
Scan troubleshooting
Use this section to solve these scan problems:
• Scan halts
Troubleshooting
• Scan fails
• Scanned image is blank
• Scanned image is incorrectly cropped
• Scanned image has incorrect page layout
• Text format is incorrect
• Scanned image shows dotted lines instead of text
• Text is incorrect or missing
Scan halts
Solution: Turn off the computer and then turn it back on.
If this does not work, try changing the scan to a lower resolution in the software.
Cause: The computer system resources may have been low.
Scan fails
• Solution 1: Make sure your computer is turned on
• Solution 2: Make sure your computer is connected to the product by a USB cable
• Solution 3: Make sure the HP Photosmart Software is installed on your computer
• Solution 4: Make sure the HP Photosmart Software is running on your computer
• Solution 5: Make sure you have sufficient computer memory
Solution 1: Make sure your computer is turned on

Solution: Turn on your computer.
Cause: The computer was not turned on.
Solution 2: Make sure your computer is connected to the product by a USB cable
Solution: Connect your computer to the product with a standard USB cable.
For more information, see the Setup Guide.
Cause: Your computer was not connected to the product by a USB cable.
Downloaded from ManualsPrinter.com Manuals Scan troubleshooting 129

Chapter 12
Solution 3: Make sure the HP Photosmart Software is installed on your computer

Solution: Insert the product installation CD and install the software.
For more information, see the Setup Guide.
Troubleshooting
Cause: The HP Photosmart Software was not installed on your computer.

Solution 4: Make sure the HP Photosmart Software is running on your computer

Solution: Open the software you installed with the product and try scanning again.
NOTE: To check to see whether the software is running, right-click on the HP

Digital Imaging Monitor icon in the system tray at the far right of the Windows
taskbar. Pick a device in the list, and then click Display Status.
Cause: The HP Photosmart Software was not running on your computer.

Solution 5: Make sure you have sufficient computer memory

Solution: Close all applications that are not in use. This includes applications that
run in the background, such as screen savers and virus checkers. If you turn off your
virus checker, remember to turn it back on after you finish your scan.
130 Troubleshooting
If this problem occurs frequently, or if you encounter memory problems while using
other applications, you might need to add more memory to your computer. See the
user guide that came with your computer for more information.
Cause: Too many applications were running on your computer. These applications
occupied your computer memory.
Troubleshooting
Scanned image is blank
Solution: Load your original print side down on the right front corner of the glass.
Scanned image is incorrectly cropped

Solution: The autocropping feature in the software crops anything that is not part
of the main image. Sometimes this might not be what you want. In that case, turn off
autocropping in the software and crop the scanned image manually, or not at all.
Cause: The software was set to automatically crop scanned pictures.
Scanned image has incorrect page layout

Solution: Turn off autocropping in the software to retain the page layout.
Cause: The automatic cropping feature in the software was changing the page
layout.
Text format is incorrect

Solution: Some applications cannot handle framed text formatting. Framed text is
one of the scan document settings in the software. It maintains complex layouts, such
as multiple columns from a newsletter, by putting the text in different frames (boxes)
in the destination application. In the software, select the correct format so that the
scanned text layout and formatting are retained.
Cause: The scan document settings were incorrect.
Downloaded from ManualsPrinter.com Manuals Scan troubleshooting 131

Chapter 12
Scanned image shows dotted lines instead of text

Solution: Make a black-and-white copy of the original and then scan the copy.
Cause: If you used the Text image type to scan text that you plan to edit, the
scanner might not recognize color text. The Text image type scans at 300 x 300 dpi,
in black and white.
If you are scanning an original that has graphics or artwork surrounding the text, the
Troubleshooting
scanner might not recognize the text.
Text is incorrect or missing

• Solution 1: Make sure that the brightness is set appropriately in the software
• Solution 2: Make sure that the glass and the back of the document lid are clean
• Solution 3: Make sure that the scan document settings are set to the correct optical
character recognition (OCR) language
Solution 1: Make sure that the brightness is set appropriately in the software
Solution: Adjust the brightness in the software, and then rescan the original.
To adjust the brightness

1. In the HP Scanning window, click Lighten/Darken in the Basic menu or the
Tools panel.
2. Adjust the brightness indicators.
Cause: The brightness was not set correctly in the software.
Solution 2: Make sure that the glass and the back of the document lid are clean
Solution: Turn off the product, unplug the power cord, and use a soft cloth to wipe
the glass and the back of the document lid.
• Clean the glass
Cause: The glass and the back of the document lid were not clean.
Solution 3: Make sure that the scan document settings are set to the correct optical
character recognition (OCR) language
Solution: Select the correct OCR language in the software.
132 Troubleshooting
Recognition (OCR) software might not be installed on your computer. To install
the OCR software, you must re-insert the software disk and select OCR under the
See the documentation that came with Readiris, or whichever OCR software you use,
for information on how to select the OCR language.
Troubleshooting
Cause: The scan document settings were not set to the correct optical character
recognition (OCR) language.
The OCR language tells the software how to interpret the characters it sees in the
original image. If the OCR language does not match the language in the original, the
scanned text might be incomprehensible.
Errors
If the product has an error, the lights on the product might flash, or an error message
might appear on your computer screen.
• Flashing lights
• Product messages
• File messages
• General user messages
• Paper messages
• Power and connection messages
• Print cartridge messages
Flashing lights
The lights on the HP All-in-One flash in special sequences to inform you about various
error conditions. Refer to the following table for information on solving your error condition
based on which lights are on or blinking on the HP All-in-One.
On light Paper Check Paper Descriptio Solution

light Print Type n
Cartridge lights
light
Off Off Off Both off The HP All- Press the On button to turn the
in-One is HP All-in-One on.
turned off.
Blinking Off Off 1 On, The HP All- Wait for the HP All-in-One to
in-One is finish.
1 Off
processing
a job, such
as print,
scan, copy,
or
alignment.
Downloaded from ManualsPrinter.com Manuals Errors 133

Chapter 12
(continued)
light Print Type n
Cartridge lights
light
Blink faster Off Off 1 On, The HP All- Wait for the HP All-in-One to
for 3 1 Off in-One is finish.
seconds busy.
and then
Troubleshooting
On
Blink for 20 Off Off 1 On, Scan was Make sure the computer is
seconds 1 Off pressed, turned on, the HP All-in-One
and then and there software is installed, and the
On was no computer is connected to the
response HP All-in-One with a USB
from the cable.
computer.
On Blinking Off 1 On, The HP All- Load paper and press any
in-One is button.
1 Off
out of
paper.
The HP All- Clear the paper jam, and

in-One has press any button.
a paper
jam.
Paper-size Change the paper in the tray

setting does or the size setting in the
not match software.
the paper
size
detected in
the input
tray.
On Off Blinking 1 On, Print Raise the door to close it.

1 Off cartridge
door is
open.
The print Install or remove and reinsert

cartridges print cartridges.
are missing
or not
seated
correctly.
The tape Remove print cartridge,

was not remove tape, and reinsert
removed print cartridge.
from the
print
cartridge.
The print The print cartridge might not

cartridge is be supported for use in the
not HP All-in-One. See the Order
intended for Supplies chapter in the User
use in this Guide.
134 Troubleshooting
(continued)
light Print Type n
Cartridge lights
light
HP All-in-
One.
The print 1. Remove the black print
Troubleshooting
cartridge cartridge.
might be 2. Close the print cartridge
defective. door.
3. Check the On light.
• If the On light blinks,
replace the tri-color
print cartridge.
• If the On light remains
steadily lit, replace
the black print
cartridge.
On Blinking Blinking 1 On, The print Open the print cartridge door,
1 Off carriage is and check that the carriage is
stalled. not blocked.
On Blinking Blinking Both The control 1. Turn the HP All-in-One

blinking panel off.
overlay is 2. Attach the control panel
not overlay using the
attached or instructions in the Setup
is not Guide.
attached
3. Turn the HP All-in-One
properly.
back on.
Blinking Blinking Blinking Both off Scanner Turn the HP All-in-One off,
failure then on again.
If the problem persists,
contact HP customer support.
Blinking Blinking Blinking Both The HP All- 1. Turn the HP All-in-One

blinking in-One has off.
a fatal error. 2. Unplug the power cord.
3. Wait a minute, then plug
the power cord back in.
4. Turn the HP All-in-One
back on.
If the problem persists,
contact HP Support.
Product messages
The following is a list of product-related error messages:
• Door open
• Firmware revision mismatch
• Mechanism error
• Memory is full

Chapter 12
• Scan errors
• Unable to print
• Product might not be correctly installed
• Product was not found
• Product could not find available scan destinations
• Required software component was not found or was incorrectly installed
Troubleshooting
• Error occurred while communicating with the product
Door open
Solution: Close the print cartridge door.
Cause: The print cartridge door was open.
Firmware revision mismatch

Solution: To find support and warranty information, go to the HP Web site at
www.hp.com/support. If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
Cause: The revision number of the product firmware does not match the revision
number of the software.
Mechanism error
• Solution 2: Make sure the print carriage is not blocked

Clear paper jams
136 Troubleshooting
Solution 2: Make sure the print carriage is not blocked
Troubleshooting
Cause: The print carriage was blocked.
Memory is full
Solution: Try making fewer copies at a time.
Cause: The document you are copying has exceeded the memory of the product.
Scan errors
Review this section if you receive an error such as one of the following:
• An error occurred communicating with the scanning device. Please ensure that the
scanning device is connected properly and try again.
• The scanning device could not be initialized.
• The scanning device could not be found.
• An internal error has occurred.
• The computer cannot communicate with the scanning device.
NOTE: Before starting to troubleshoot, make a copy to verify that the hardware is
functioning correctly. If you cannot make a copy, see Hardware setup
troubleshooting for more troubleshooting information.
Try each of the following solutions separately. After completing the steps for each
solution, try to scan again. If the product still does not work, then go to the next solution.
• Solution 1: Uninstall and reinstall the software
• Solution 2: Refresh the Windows Device Manager
• Solution 3: Check the Digital Imaging Monitor
• Solution 4: Check the status of the product
• Solution 5: Check the power supply
• Solution 6: Check the USB cable connection

Chapter 12
• Solution 7: Scan with Windows Image Acquisition (WIA)

• Solution 8: Disable the Lexbces service
• Solution 9: Run the Scan Diagnostic utility
• Solution 10: Install a patch
• Solution 11: Check the USB chipset and controller
• Solution 12: Uninstall the software and reset the product
Troubleshooting
Solution 1: Uninstall and reinstall the software

Solution: Verify that the software was installed correctly. Open the HP Solution
Center and verify that all the icons and buttons are present.
If the appropriate icons and buttons for your product (such as Make Copies) do not
appear, your installation might not be complete, and you might need to uninstall and
then reinstall the software. Do not simply delete the application files from your hard
drive. Make sure to remove them properly using the uninstall utility provided with the
software.
To uninstall from a Windows computer
NOTE: Use this method if Uninstall is not available in the Windows Start menu
(click Programs or All Programs, HP, Deskjet F2200 All-In-One series,
Uninstall).
1. Open the Windows control panel and double-click Add or Remove Programs.
NOTE: The procedure to open the control panel varies by operating system.
If you are not sure how to do this, see the Windows Help.
2. Select HP Deskjet All-In-One Driver Software, and then click Change/

Remove.
Follow the onscreen instructions.
3. Disconnect the product from your computer.
5. Insert the product CD-ROM into your computer’s CD-ROM drive and then start
the Setup program.
6. Follow the onscreen instructions and the instructions provided in the Setup Guide
that came with the product.
After you have reinstalled the software, try to scan again.
Cause: The software installation was not complete.
138 Troubleshooting
Solution 2: Refresh the Windows Device Manager
Solution: Refresh the Windows Device Manager.
To refresh the Windows Device Manager

1. On the Windows taskbar, click Start, right-click My Computer, and then click
Properties.
Troubleshooting
2. Click the Hardware tab, and then click Device Manager.
3. Double-click Universal Serial Bus Controllers.
4. Click USB Composite Device, click Action, and then click Uninstall.
If a screen appears to confirm the deletion, confirm the deletion.
5. Disconnect the USB cable from the product.
6. Wait a few seconds, and then reconnect the cable.
This should restart the Windows device detection (Plug and Play). A New
Hardware found screen might appear.
7. Click Next through all of the screens that appear in the Wizard to install the USB
Composite Device.
8. Click Finish to finish the installation.
9. Try to scan again.
10. If these steps do not resolve the problem, try using a different USB cable to
connect the product to the computer.
Cause: Communication problems between the product and the USB controller
caused this error to occur. This might be caused by an incomplete installation, a USB
cable longer than 3 meters (9.8 feet) in length, or a defective USB cable.

Chapter 12
Solution 3: Check the Digital Imaging Monitor

Solution: Verify that the Digital Imaging Monitor is running.
To check that the Digital Imaging Monitor is running

1. Look for the Digital Imaging Monitor icon in the system tray at the lower right
side of the screen, near the time.
Troubleshooting
2. If the Digital Imaging Monitor icon is not present, restart the computer.
3. After the computer restarts, try to scan again.
Cause: The Digital Imaging Monitor was not running.
Solution 4: Check the status of the product

Solution: Check the status of the product in the HP Solution Center.
To check the status of the product

1. On the Windows taskbar, click Start, Programs or All Programs, HP, HP
Solution Center.
2. Verify that the product is listed in the Select Device area or that the appropriate
tab is selected.
3. Click Status.
If the product is working properly, a message appears indicating your product is
ready.
4. If you receive a Disconnected error message, then check whether there is
another instance or another tab for the product with a copy number included, such
as HP Deskjet F2200 All-in-One series 2.
140 Troubleshooting
5. Select the second instance of the product and repeat steps 2 through 4.
Cause: There might have been two instances of the product connected to the
HP Solution Center.
Troubleshooting
Solution 5: Check the power supply
Solution: Check the power supply.
To check the power supply

1. Make sure the power cord is firmly connected to both the product and the power
adaptor. Plug the power cord into a power outlet, surge protector, or power strip.
1 Power connection
2 Power cord and adaptor
2. Make sure the product is turned on.

3. If the product is not receiving electrical power, connect it to another power outlet.
4. Turn off the product and reset it by disconnecting the power cord.
5. Wait 5 seconds, and plug in the power cord.
6. Turn on the product.
Cause: The product was not properly connected to a power supply or needed to be
reset.

Chapter 12
Solution 6: Check the USB cable connection

Solution: Check USB connection between the product and the computer.
To check the USB connection

1. Verify that the USB cable is securely plugged into the USB port on the back of
the product.
Troubleshooting
2. Make sure the other end of the USB cable is plugged into a USB port on your
computer.

If the scan fails, continue to the next step.
4. Do one of the following, depending upon how the product is connected to the
computer:
• If the USB cable is connected to a USB hub, try unplugging and replugging
the USB cable into the hub. If that does not work, try turning off the hub and
then turning it on again. Finally, try disconnecting the cable from the hub and
connecting it directly to the computer.
• If the USB cable is connected to a docking station for a laptop, disconnect the
cable from the docking station and connect it directly to the computer.
• If the USB cable is directly connected to the computer, try plugging it into
another USB port on the computer.
5. If there are other USB devices connected to the computer, disconnect the other
devices, except for the keyboard and the mouse.
6. Check the USB cable to make sure it is functioning properly.
NOTE: If you are using an older cable, it might not be working properly. Try
connecting it to another product to see if the USB cable works. If you
experience problems, the USB cable might need to be replaced. Also verify
142 Troubleshooting
7. If another USB cable is available, try using that one instead.
8. Restart the computer.
Cause: The product was not properly connected to the computer.
Troubleshooting
Solution 7: Scan with Windows Image Acquisition (WIA)
Solution: Try scanning with Windows Image Acquisition (WIA) instead of the
HP Solution Center.
To scan using WIA

the product.
The USB icon on the cable faces up when the cable is properly connected.
computer.
4. On the Windows taskbar, click Start, click Programs or All Programs, and then
click Accessories.
5. Click Imaging.
6. From the Imaging application, click File and then click Select Device.
7. Select the product from the TWAIN source list.
8. Click File, and then click Scan New.
Imaging for Windows will scan from the product using TWAIN software instead of
the HP Solution Center.
Cause: If you could scan using WIA, this indicates that there was a problem with
the HP Solution Center. You can continue to use WIA to scan, or try the next solution.

Chapter 12
If you could not scan using WIA, try the next solution.
Solution 8: Disable the Lexbces service

Solution: Check if the Lexbces service is started, and disable it.
If a Lexmark or Dell all-in-one device is connected with a USB cable to a computer
Troubleshooting
where product is installed, the HP software might not scan because the Lexbces
service is running.
NOTE: This solution only applies if you have a Lexmark or Dell all-in-one. If you
do not, try the next solution.
To check for and disable the service

1. Log into Windows as an Administrator.
2. Press the Ctrl + Alt + Delete to open the Task Manager.
3. Click the Processes tab.
4. If the Lexbceserver service is listed in the Image Name list, disable it.
To disable the service

a. On the Windows taskbar, click Start, right-click My Computer, and then click
Manage.
The Computer Management appears.
b. Double-click Services and Applications, and then double-click Services.
c. In the right pane, right-click Lexbceserver, and then click Properties.
d. On the General tab, in the Service status area, click Stop.
e. From the Startup type drop-down menu, select Disabled, and then click
OK.
f. Click OK to close the dialog box.
5. Back up the Registry.
To back up the Registry

a. On the Windows taskbar, click Start.
b. Depending on your operating system, do one of the following:
• Windows Vista: In Start Search, type regedit, and then press Enter.
When the User Account Control dialog box appears, click Continue.
• Windows XP: Click Run. When the Run dialog box appears, type
regedit, and then press Enter.
• Windows 2000: Click Registry, and then click Export Registry
The Registry Editor appears.
c. In the Registry Editor, select My Computer.
d. With My Computer highlighted, click File, and then click Export.
e. Browse to a storage location that is easy for you to remember; for example:
My Documents or Desktop.
f. In the Export Range area, select All.
144 Troubleshooting
g. Enter a filename for the backed up Registry.
HP suggests naming the file with the current date; for example: Registry
Backup 04_01_07.
h. Click Save to save the Registry.
6. Edit the registry.
To edit the Registry
Troubleshooting
a. Select the HKEY_LOCAL_MACHINE\System\CurrentControlSet
\Services\Spooler Registry key.
Details of the Registry key appears on the pane to the right.
b. Check the DependOnService data string (in the pane on the right) to see if
lexbces is listed in the Data column.
c. If the Data column contains lexbces, right-click DependOnService and
select Modify.
Do one of the following:
• If you see only lexbces, but not RPCSS, delete lexbces and enter
RPCSS.
• If you see both lexbces and RPCSS, delete only lexbces and keep
RPCSS.
d. Click OK.
7. Restart the computer, and then try to scan again.
If you can scan successfully, then proceed with the next step to restart the
Lexbcserver service.
NOTE: Restarting the service enables the normal functionality of the

Lexmark or Dell devices without affecting HP software.
8. Restart the Lexbcserver service.
To restart the service

a. On the Windows taskbar, click Start, right-click My Computer, and then click
Manage.
The Computer Management screen appears.
b. Double-click Services and Applications, and then double-click Services.
c. In the right pane, right-click Lexbceserver, and then click Properties.
d. On the General tab, in the Service status area, click Start.
e. From the Startup type drop-down menu, select Automatic, and then click
OK.
f. Click OK to close the dialog box.
Cause: The Lexbceserver service installed by a Lexmark printer, Lexmark all-in-
one, or Dell all-in-one, caused a scan communication error.

Chapter 12
Solution 9: Run the Scan Diagnostic utility

Solution: Download and run the Scan Diagnostic utility to find and correct
problems with your product.
To download and run the Scan Diagnostic utility

1. Go to: www.hp.com and click Software and driver downloads.
2. Select Download drivers and software (and firmware).
Troubleshooting
3. Type your product name and model number in the field provided, and then press
Enter.
4. Select the operating system of your computer where the HP software is installed.
5. Go to the Utility section and download the HP Scan diagnostic utility.
6. Try to scan.
If an error condition is identified with any of the HP software components, a red
X is displayed next to the component. If there is no error condition, a green check
mark is displayed next to the component. The utility is equipped with a Fix button
to correct the error conditions.
Cause: There was a problem with the connections between the product and the
computer.
Solution 10: Install a patch

Solution: Download and install the unexpected internal error and
communications failure patch.
This patch resolves the An unexpected internal error has occurred error and other
communication failures with the product.
To install the patch

1. Go to: www.hp.com and click Software and driver downloads.
2. Select Download drivers and software (and firmware).
3. Select the operating system of your computer where the HP software is installed.
4. Go to the Patch section and download the HP Image zone/photo and imaging
unexpected internal error and communications failure patch.
5. Double-click the patch to install it on the computer.
6. Try to scan.
Cause: You needed to install the unexpected internal error and
communications failure patch.
Solution 11: Check the USB chipset and controller

Solution: Check the USB chipset and controller.
Scan communication errors can occur because of compatibility issues with USB
chipsets installed on the computer. This can be caused by a mismatch in the
146 Troubleshooting
handshake timing between HP device chipset and certain types of USB chipsets on
the computer.
To check the USB chipset and controller

1. On the Windows taskbar, click Start, right-click My Computer, and then click
Properties.
2. Click the Hardware tab, and then click Device Manager.
Troubleshooting
3. Open Universal Serial Bus Controllers by clicking the plus sign (+) next to it.
4. Check if you have one of the following chipsets listed:
• SIS 7001 USB host controller
• ALI chipsets
• NEC universal host controllers
• Intel 82801 AA, Intel 82801BA/BAM
NOTE: This is not a comprehensive list. If you are experiencing

communication issues while trying to scan, follow the steps below to resolve
the issue.
5. Disconnect all USB devices (printers, scanners, cameras, etc.) from the
computer, except the mouse or keyboard.
6. Reconnect the USB cable to the USB port on the back of the product.
7. Reconnect the other end of the USB cable to a USB port on your computer.

Chapter 12
adaptor. Plug the power cord into a power outlet, surge protector or power strip.
Troubleshooting
1 Power connection

10. Print a self-test report to test the basic standalone functionality of the product.
See the following procedure for more information about printing a self-test report.
11. Try to scan.
If the scan is successful, other USB devices connected to the computer might be
causing the problem.
12. If the scan is successful, then connect one USB device at a time to the computer.
13. Test the scanning functionality after each connection, until you identify which
piece of equipment is causing the problem.
14. If the product fails to scan. Or, does not establish communication with the
computer along with any of the USB devices plugged in, then connect a powered
USB hub between the product and the computer.
This might help to establish, or to maintain, communication between the computer
and the product. See the following section for more information about USB hubs.

148 Troubleshooting
complete.
• If more than a few lines in a pattern are broken, this might indicate a problem
with the nozzles. You might need to clean the print cartridges.
• If the black line is missing, faded, streaked, or shows lines, this might indicate
a problem with the black print cartridge in the right slot.
Troubleshooting
More information about using a USB hub

• Verify that the USB hub is a powered hub and the power adapter is plugged in.
Some powered hubs do not include the power adapter as a standard item.
• The hub must be plugged into a power source.
• Some hubs cannot handle more than four full-power USB devices. You can
connect a maximum of five hubs to the system.
• If the product has trouble with a hub when the hubs are connected together, or
there are more than four devices on the hub, connect the product to the hub that
is directly connected to the computer (unless there are known issues).
Cause: There was a compatibility issue with USB chipsets installed on the
computer.
Solution 12: Uninstall the software and reset the product

Solution: Uninstall the software completely, and then reinstall it.
To uninstall the software and reset the product

1. Disconnect and reset the product.
To disconnect and reset the product

a. Make sure the product is turned on.
b. Press the On button to turn off the product.
c. Disconnect the power cord from the back of the product.
d. Reconnect the power cord to the back of the product.
e. Press the On to turn on the product.
2. Uninstall the software completely.
NOTE: It is important that you follow the uninstall procedure carefully to

ensure you have removed the software completely from the computer, before
reinstalling it.

Chapter 12
To uninstall the software completely

a. On the Windows taskbar, click Start, Settings, Control Panel, (or just
Control Panel).
b. Double-click Add/Remove Programs (or click Uninstall a program).
c. Remove all the items that are related to the HP scanning software.
CAUTION: If the computer is manufactured by HP or Compaq, do not

Troubleshooting
remove any applications other than those listed below.

• HP Imaging device functions
• HP Document Viewer
• HP Photosmart Essential
• HP Image Zone
• HP Photo and imaging gallery
• HP Photosmart, Officejet, Deskjet, (with product name and software
version number)
• HP Software update
• HP Share to web
• HP Solution Center
• HP Director
• HP Memories Disk Greeting Card Creator 32
d. Go to C:\Program Files\HP or C:\Program Files\Hewlett-
Packard (for some older products) and delete the Digital Imaging
folder.
e. Go to C:\WINDOWS and rename the twain_32 folder to twain_32 old.
3. Turn off programs that run in the background.
NOTE: When the computer is turned on, a software group called the
Terminate and Stay Resident (TSR) programs automatically loads. These
programs activate some of the computer utilities, such as the anti-virus
software, but are not required for the computer to function. Occasionally,
TSR's prevent the HP software from loading so that it does not install properly.
In Windows Vista, Windows XP, and Windows 2000, use the MSCONFIG
utility to prevent TSR programs and services from starting up.
To turn off programs that run in the background

a. On the Windows taskbar, click Start.
b. Depending on your operating system, do one of the following:
• In Windows Vista: In Start Search, type MSCONFIG, and then press
Enter.
When the User Account Control dialog box appears, click Continue.
• In Windows XP and Windows 2000: Click Run. When the Run dialog box
appears, type MSCONFIG, and then press Enter.
The MSCONFIG utility application appears.
c. Click the General tab.
d. Click Selective Startup.
150 Troubleshooting
e. If there is a check mark next to Load Startup Items, click the check mark to
remove it.
f. Click the Services tab, and select the Hide All Microsoft Services box.
g. Click Disable all.
h. Click Apply, and then click Close.
NOTE: If you receive a message stating Access is denied while making
Troubleshooting
changes, click OK and continue. The message will not prevent you from
making the changes.
i. Click Restart to apply the changes to the computer during the next restart.
After the computer restarts, the You’ve used system configuration utility
to make changes to the way windows starts message appears.
j. Click the check box next to Do not show this message again.
4. Run the Disk Cleanup utility to delete temporary files and folders.
To run the Disk Cleanup utility

a. On the Windows taskbar, click Start, click Programs or All Programs, and
then click Accessories.
b. Click System Tools, and then click Disk Cleanup.
The Disk Cleanup analyzes the hard drive and then presents a report with a
list of components to delete.
c. Select the appropriate check boxes to remove the unnecessary components.
More information about the Disk Cleanup utility

The Disk Cleanup utility frees hard disk space on your computer by doing the
following:
• Deleting temporary Internet files
• Deleting downloaded program files
• Emptying the Recycle Bin
• Deleting files from your temporary folder
• Deleting files created by other Windows tools
• Removing optional Windows components that you do not use
d. After selecting the components to remove, click OK.

Chapter 12
5. Install the software.
To install the software

a. Insert software CD into the CD-ROM drive of the computer.
The software installation will start automatically.
NOTE: If the installation does not run automatically, from the Windows
Troubleshooting
Start menu, click Start Search (or Run). In the Start Search (or Run
dialog box), type d:\setup.exe, and then press Enter. (If your CD-ROM
drive is not assigned to drive letter D, enter the appropriate drive letter.)
b. Follow the prompts on the computer screen to install the software.

6. Try to scan.
Cause: The software needed to be completely uninstalled and reinstalled.
Unable to print
• Solution 1: Print a self-test report
• Solution 2: Clear the print queue
• Solution 3: Disconnect and reconnect the USB cable
• Solution 4: Verify the driver configuration
• Solution 5: Check if the printer is paused or offline
• Solution 6: Clear the print queue manually
• Solution 7: Restart the print spooler
• Solution 8: Check the software application
Solution 1: Print a self-test report

Solution: Print a self-test report to see if the product can print and is communicating
with the computer.

152 Troubleshooting
complete.
a problem with the black print cartridge in the right slot.
Troubleshooting
If the self-test report fails to print, make sure you set up the product properly. See the
Setup Guide that came with the product for information about setting it up.
Cause: The product was not set up properly.
Solution 2: Clear the print queue

Solution: Restart your computer to clear the print queue.
To clear the print queue

2. After the computer has restarted, check the print queue.
a. Depending upon your operating system, do one of the following:
• Windows Vista: On the Windows taskbar, click Start, click Control
Panel, and then click Printers.
• Windows XP: On the Windows taskbar, click Start, click Control Panel,
and then click Printers and Faxes.
• Windows 2000: On the Windows taskbar, click Start, point to Settings,
and then click Printers.
b. Double-click the icon for your product to open the print queue.
If there are no print jobs pending, the issue might have been resolved.
3. Try to print again.
Cause: The computer needed to be restarted to clear the print queue.
Solution 3: Disconnect and reconnect the USB cable

Solution: Disconnect the USB cable from the computer and product, and then
reconnect it.
To disconnect and reconnect the USB cable

1. Disconnect the USB cable from the product.
2. Disconnect the USB cable from the computer.
3. Leave the USB cable disconnected for 5-6 seconds.

Chapter 12
4. Reconnect the USB cable to the product and the computer.

Troubleshooting
After reconnecting the USB cable, the product should start printing the jobs in
queue.
NOTE: If you are connecting the product through a USB hub, make sure the
hub is turned on. If the hub is on, try connecting directly to your computer.
5. If the product does not start printing automatically, start another print job.
Cause: The USB cable needed to be disconnected.
Solution 4: Verify the driver configuration

Solution: Check to make sure the product is set as the default printer and it is using
the correct printer driver.
To verify that the product is set as the default printer

1. Depending upon your operating system, do one of the following:
• Windows Vista: On the Windows taskbar, click Start, click Control Panel, and
then click Printers.
• Windows XP: On the Windows taskbar, click Start, click Control Panel, and
then click Printers and Faxes.
• Windows 2000: On the Windows taskbar, click Start, point to Settings, and
2. Make sure the correct product is set as the default printer.
The default printer has a check mark in a black circle next to it.
3. If the wrong product is set as the default printer, right-click the correct product and
select Set as Default.
154 Troubleshooting
To verify the print driver
Troubleshooting
2. Right-click the icon next to the product, and select Properties.
3. Click the Ports tab to verify that the product is using the correct port.
The port that the product is using is highlighted and has a check mark next to it.
The product should be set to use a DOT4 or the USB00X (where X is replaced
by a number) port.
4. If the product is using the wrong port, click the correct port to select it.
The port that the product is now using is highlighted and has a check mark next
to it.
6. Check the driver listed in the Driver drop-down menu to verify that the product is
using the correct driver.
The name of your product should be listed as the driver.
7. If the wrong driver is selected, select the correct driver from the Driver drop-down
menu.
8. Click OK to save your changes.
Cause: If there was more than one product configured on the same computer, the
product in use was not be set as the default printer, or the wrong driver might have
been configured.
Solution 5: Check if the printer is paused or offline

Solution: Check to make sure the product is not paused or offline.
To check if the printer is paused or offline

then click Printers
2. Double-click the icon for your product to open the print queue.

Chapter 12
3. On the Printer menu, make sure there are no check marks next to Pause
Printing or Use Printer Offline.
On the Printer menu, make sure there are no check marks next to Pause
Printing or Use Printer Offline. If a check mark is present on either option, click
the menu option to remove it. If the menu has the Use Printer Online option,
select that option to put a check mark next to it.
4. If you made any changes, try to print again.
Troubleshooting
Cause: The product was paused or offline.

Solution 6: Clear the print queue manually

Solution: Manually clear the print queue.
To clear the print queue manually

2. Double-click the icon for your product to open the print queue.
3. On the Printer menu, click Cancel all documents or Purge Print Document,
and then click Yes to confirm.
4. If there are still documents in the queue, restart the computer and try printing
again after the computer has restarted.
5. Check the print queue again to make sure it is clear, and then try to print again.
If the print queue is not clear, or if it is clear but jobs are still failing to print, proceed
to the next solution.
Cause: The print queue needed to be manually cleared.
Solution 7: Restart the print spooler

Solution: Restart the print spooler.
To stop and restart the print spooler

2. Double-click Administrative Tools, and then double-click Services.
3. Scroll down the list and click Print Spooler, and then click Stop to stop the
service.
4. Click Start to restart the service, and then click OK.
5. Restart the computer and try printing again after the computer has restarted.
156 Troubleshooting
Cause: The print spooler needed to be restarted.
Solution 8: Check the software application

Solution: Verify whether the software application is the problem.
Troubleshooting
To verify the software application
1. Close the software application and reopen it.
2. Try to print again from the software application.
NOTE: The printer might not support printing from a DOS application.
Determine if the software application is Windows-based or DOS-based by
checking the system requirements of the application.
3. Try printing from Notepad to see if the issue is the software application or the
driver.
To print from Notepad

a. On the Windows taskbar, click Start, and then click Programs or All
Programs.
b. Click Accessories, and then click Notepad.
c. Type a few characters of text into Notepad.
d. Click File, and then click Print.
4. If printing is successful from Notepad but not the software application, contact the
manufacturer of that application for support.
Cause: The software application was be failing or could not interface with the print
driver incorrectly.
Product might not be correctly installed

• Solution 1: Reset the product
• Solution 2: Check the power cord and USB cable
• Solution 3: Restart the computer
• Solution 4: Uninstall and reinstall the product
• Solution 5: Uninstall and reinstall the HP Photosmart Software
Solution 1: Reset the product

Solution: Turn off the product and reset it by disconnecting the power cord. Wait
60 seconds, and then plug in the power cord. Turn on the product.
Cause: You needed to reset the product.

Chapter 12
Solution 2: Check the power cord and USB cable

Solution: Make sure that the power cord and USB cable are properly attached and
plugged in. Also, make sure that the product is turned on.
Troubleshooting

1 Power connection
3 Power outlet

158 Troubleshooting
the product.
computer.
Troubleshooting
computer:

Cause: The power cord or USB cable was not attached properly.

Chapter 12
Solution 3: Restart the computer

Solution: Restart the computer.
Cause: You might not have restarted the computer after installing the product
Troubleshooting
software. Or, there might have been another problem with the computer.
Solution 4: Uninstall and reinstall the product

Solution: Uninstall the product from the Printers and Faxes control panel and then
reinstall it.
To uninstall and reinstall the product

1. Disconnect the USB cable between the product and the computer.
2. On the Windows taskbar, click Start, Printers and Faxes.
3. Right-click the product and select Delete.
4. Wait several seconds, and then reconnect the product to the computer with the
USB cable.
5. Follow any onscreen prompts to reinstall the product.
Cause: There might have been a problem when you originally installed the product.
Solution 5: Uninstall and reinstall the HP Photosmart Software

Solution: Uninstall the complete HP Photosmart Software from the computer and
then reinstall it using the CD that came with your product.
To uninstall and reinstall the software

1. On the Windows taskbar, click Start, Settings, Control Panel.
2. Double-click Add/Remove Programs.
3. Remove all the items that are related to the HP scanning software.
A message appears on the computer to restart after removing some programs
from the Add/Remove Programs list.
4. Select Click here to restart later.
5. Disconnect the product from your computer and then restart your computer.
160 Troubleshooting
6. Insert the HP Photosmart CD-ROM into your computer’s CD-ROM drive and then
start the Setup program.
NOTE: If the Setup program does not appear, locate the setup.exe file on
the CD-ROM drive and double-click it.
Troubleshooting
8. If you are still having trouble scanning, remove the following additional
applications from the Add/Remove Programs list, if they are present.

• HP Image Zone
• HP Photosmart, Officejet, Deskjet, (with product name and software version
number)
• HP Share to web
• HP Director
Cause: There might have been a problem when you originally installed the
Product was not found



Chapter 12


Troubleshooting
1 Power connection
3 Power outlet

162 Troubleshooting
the product.
computer.
Troubleshooting
computer:


Chapter 12

Troubleshooting

reinstall it.

USB cable.


164 Troubleshooting
Troubleshooting

• HP Image Zone
number)
• HP Share to web
• HP Director
Product could not find available scan destinations



Chapter 12


Troubleshooting


• HP Image Zone
number)
• HP Share to web
• HP Director
166 Troubleshooting
Required software component was not found or was incorrectly installed

Troubleshooting

• HP Image Zone
number)
• HP Share to web
• HP Director

Chapter 12
Error occurred while communicating with the product

Troubleshooting

• Solution 6: Contact HP support for service



1 Power connection
3 Power outlet
168 Troubleshooting
Troubleshooting
the product.
computer.

computer:

Chapter 12

Troubleshooting



reinstall it.

USB cable.


170 Troubleshooting
Troubleshooting

• HP Image Zone
number)
• HP Share to web
• HP Director
Solution 6: Contact HP support for service

Solution: If you have completed all of the steps provided in the previous solutions
and are still having a problem, contact HP support for service.
Go to: www.hp.com/support.
If prompted, choose your country/region, and then click Contact HP for technical
support.

Chapter 12
Cause: You might need assistance to enable the product or software to function
properly.
File messages
The following is a list of file-related error messages:
Troubleshooting
• Error reading or writing the file

• File not found
• File format not supported
• Invalid file name
• Supported file types for the HP All-in-One
Error reading or writing the file

Solution: Check to see if you have the right folder and file name.
Cause: The product software could not open or save the file.
File not found

Solution: Close some applications and try the task again.
Cause: There was not enough available memory on your computer to create a print
preview file.
File format not supported

Solution: Open the file in another application, and save it in a format that the
product software recognizes.
Supported file types for the HP All-in-One
Cause: The product software did not recognize or support the file format of the
image you are trying to open or save. If the file extension indicates it is a supported
file type, the file might be corrupted.
Invalid file name

Solution: Make sure that you are not using any invalid symbols in the file name.
Cause: The file name you entered was invalid.
172 Troubleshooting
Supported file types for the HP All-in-One
Refer to the following for the supported file formats:
• The HP Photosmart software supports the following file formats: BMP, DCX, FPX,
GIF, JPG, PCD, PCX, TIF, PICT, PSD, PCS, EPS, TGA, SGI, PDF, and PNG
• When scanning, the HP Photosmart Software enables you to save an image in the
following file formats: BMP, DCX, FPX, GIF, JPG, PCD, PCX, and TIF
Troubleshooting
General user messages
The following is a list of messages related to common user errors:
• Cannot crop
• Disconnected
• No scan options
• Out of disk space
Cannot crop
• Solution 1: Close applications that are not being used
• Solution 2: Create more space on your hard drive
Solution 1: Close applications that are not being used

Solution: Close all applications that are not in use. This includes applications that
run in the background, such as screen savers and virus checkers. If you turn off your
virus checker, remember to turn it back on after you finish your scan.
If this problem occurs frequently, or if you encounter memory problems while using
other applications, you might need to add more memory to your computer. See the
user guide that came with your computer for more information.
Cause: The computer does not have enough memory.
Solution 2: Create more space on your hard drive

Solution: Empty the Recycle Bin on your desktop. You might also need to remove
files from the hard disk; for example, delete temporary files.
Cause: For scanning, there must be at least 50 MB of space available on your
computer's hard disk.
Disconnected
Solution: Make sure your computer is turned on and is connected to the product.
Also make sure you installed the software that came with the product.

Chapter 12
Cause: Several situations can cause this error message to appear.

• Your computer was not turned on.
• Your computer was not connected to the product.
• The software that came with the product was not installed correctly.
• The software that came with the product is installed, but it was not running.
Troubleshooting
No scan options
Solution: Make sure the software is installed and running. For more information,
see the Setup Guide that came with the HP All-in-One.
Cause: The software that came with the product was not running, or has never been
installed.
Out of disk space

Solution: Close some applications and try the task again.
Cause: There was not enough available memory on your computer to perform the
task.
Paper messages
The following is a list of paper-related error messages:
• Cannot load paper from input tray
• Ink is drying
• Out of paper
• Paper jam or misfeed
• Paper mismatch
• Wrong paper width
Cannot load paper from input tray

Solution: If the product is out of paper or there are only a few sheets remaining,
load more paper in the input tray. If there is paper in the input tray, remove the paper,
gently tap the stack of paper against a flat surface, and reload the paper into the input
tray. To continue your print job, press any button on the control panel of the product.
Cause: There was not enough paper in the input tray.
Ink is drying
Solution: Leave the sheet in the output tray until the message disappears. If it is
necessary to remove the printed sheet before the message disappears, carefully hold
the printed sheet on the underside or the edges, and place it on a flat surface to dry.
Cause: Transparencies and some other media require a drying time that is longer
than normal.
174 Troubleshooting
Out of paper
• Solution 1: Replace the rear door of the product
• Solution 2: Check the paper type and the print settings
Troubleshooting
• Solution 3: Clean the rollers
• Solution 4: Contact HP support
Solution 1: Replace the rear door of the product

Solution: If you removed the rear door to clear a paper jam, replace it. Gently push
the door forward until it snaps into place.
Cause: The rear door was removed from the product.

Solution 2: Check the paper type and the print settings

Solution: Check the paper loaded in the input tray and the print settings.
To check the paper in the input tray

1. Remove the stack of paper from the input tray and verify that all the paper in the
input tray is the same size and type.
2. Replace any paper that is ripped, dusty, wrinkled, or bent.
If the paper is curled, uncurl the paper by gently bending it in the opposite direction
of the curl or replace the paper.
NOTE: Use plain paper in the product until the issue is resolved.
3. Tap the stack of paper on a flat surface to align the edges.

4. Verify that the stack of paper contains between 10 and 25 sheets of paper.

Chapter 12
5. Insert the stack of paper into the input tray with the short edge forward and the
print side down. Slide the stack of paper forward until it stops.
Troubleshooting
NOTE: Do not overload in the input tray; make sure the stack of paper fits
within the input tray and is no higher than the top of the paper-width guide.
7. Make sure the print settings, paper size and type, match the paper loaded in the
input tray.
See the following tasks for information about checking and changing these
settings.
To set the paper size

The following table lists the suggested paper size settings for the different types
of paper you can load in the input tray. Make sure to look at the long list of choices
176 Troubleshooting
in the Size list to see if a defined paper size already exists for the type of paper
you are using.
Paper type Suggested paper size settings
Copier, multi-purpose, or Letter or A4

plain papers
Troubleshooting
Envelopes Appropriate listed envelope size
Greeting-card papers Letter or A4
Index cards Appropriate listed card size (if listed sizes are not
Inkjet papers Letter or A4
Iron-on T-shirt transfers Letter or A4
Labels Letter or A4
Legal Legal
Letterhead Letter or A4
Panorama photo paper Appropriate listed panorama size (if listed sizes are not
Photo papers 10 x 15 cm (4 x 6 inch), letter, A4, or an appropriate listed

size
Transparency films Letter or A4
Custom-size papers Custom paper size
To set the paper type for printing

3. Make sure you have selected the correct printer.
6. In the Basic Options area, click the appropriate paper type from the Paper
Type list.
Cause: There was a problem with the paper loaded in the input tray, or the print
settings did not match.
Solution 3: Clean the rollers

Solution: Clean the rollers.

Chapter 12

• Lint-free cloth, or any soft material that will not come apart or leave fibers.
• Distilled, filtered, or bottled water.
To clean the rollers

1. Turn off the product and remove the power cord.
Troubleshooting
2. Remove the rear access door.
3. Dip the lint-free cloth into the purified or distilled water, and squeeze any excess
water from it.
4. Clean the rubber rollers to remove any dust or dirt buildup.
5. Replace the rear access door. Gently push the door forward until it snaps into
place.
6. Plug the power cord back in, and turn on the product.
Cause: The rollers were dirty and needed to be cleaned.
Solution 4: Contact HP support

Solution: If you have completed all of the steps provided in the previous solutions,
contact HP support for service.
If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
Cause: Your product needs servicing.
178 Troubleshooting
Paper jam or misfeed
Clear paper jams
Cause: The HP All-in-One had a paper jam.
Troubleshooting
Paper mismatch
Solution: Change the print setting or load the appropriate paper in the input tray.
Cause: The print setting for the print job did not match the paper type or size loaded
in the product.
Wrong paper width

Solution: Change the print setting or load the appropriate paper in the input tray.
Cause: The print setting for the print job did not match the paper type or size loaded
in the product.
Power and connection messages

The following is a list of power- and connection-related error messages:
• HP All-in-One not found
• Communication test failed
• Improper shutdown
• Two-way communication lost

Chapter 12
HP All-in-One not found

errors can occur. Make sure the USB cable is securely connected to the product and
the computer, as shown below.
Troubleshooting

Cause: This error applies only to USB-connected devices. The USB cable was not
plugged in properly.
Communication test failed

• Solution 1: Make sure the product is turned on
• Solution 2: Make sure the product is connected to the computer
Solution 1: Make sure the product is turned on

180 Troubleshooting
Solution 2: Make sure the product is connected to the computer
Solution: If the HP All-in-One is not properly connected to the computer,
communication errors can occur. Make sure the USB cable is connected to the HP All-
in-One and the computer as shown below.
Troubleshooting
Improper shutdown
Solution: Press the On button located on the control panel of the product to turn
the product on and off.
Cause: The last time the product was used, it was not turned off properly. If the
product is turned off by turning off the switch on a power strip or by using a wall switch,
the product can be damaged.
Two-way communication lost

• Solution 1: Make sure the product is turned on
• Solution 2: Make sure the product is connected to the computer
Solution 1: Make sure the product is turned on


Chapter 12

Solution 2: Make sure the product is connected to the computer

Troubleshooting
errors can occur. Make sure the USB cable is securely connected to the product and
the computer, as shown below.

Cause: The product was not connected to the computer.
Print cartridge messages

The following is a list of print cartridge error messages:
• Non-HP cartridges installed
• Previously used genuine HP cartridges installed
• Original HP ink has been depleted
• Low on ink
• Printing in ink-backup mode
• The print carriage is stalled
• Need alignment or alignment failed
• Print cartridge is missing, incorrectly installed, or not intended for your product
• Print cartridges missing or not detected
• Incompatible print cartridges
182 Troubleshooting
• Print cartridges in wrong slot
• Print cartridge problem
Non-HP cartridges installed

Solution: Follow the prompts on the computer screen to continue or replace the
indicated print cartridges with genuine HP cartridges.
Troubleshooting

service or repairs required as a result of using of a non-HP supply will not be
covered under warranty.

Cause: The product detected that a non-HP print cartridge was installed.
Previously used genuine HP cartridges installed

Solution: Check the print quality of the current print job. If it is satisfactory, follow
the prompts on the computer screen to continue.
Ink levels might not be available for the indicated print cartridges. Ink level warnings
and indicators provide estimates for planning purposes only. When you receive a low-
ink warning message, consider having a replacement cartridge available to avoid
possible printing delays. You do not need to replace the print cartridges until print
quality becomes unacceptable.
Cause: A genuine HP print cartridge was previously used in another printer.
Original HP ink has been depleted

Solution: Follow the prompts on the computer screen to continue or replace the
indicated print cartridges with genuine HP cartridges.
Ink levels might not be available for the indicated print cartridges. Ink level warnings
and indicators provide estimates for planning purposes only. When you receive a low-
ink warning message, consider having a replacement cartridge available to avoid
possible printing delays. You do not need to replace the print cartridges until print
quality becomes unacceptable.

service or repairs required as a result of using of a non-HP supply will not be
covered under warranty.

Chapter 12
Cause: The original HP ink in the indicated print cartridges was depleted.
Troubleshooting
Low on ink
Solution: Ink levels might not be available for the indicated print cartridges. Ink level
warnings and indicators provide estimates for planning purposes only. When you
receive a low-ink warning message, consider having a replacement cartridge
available to avoid possible printing delays. You do not need to replace the print
cartridges until print quality becomes unacceptable.
For HP product return and recycling information, visit us at: www.hp.com/recycle.
Cause: The indicated print cartridges were estimated to be low on ink and might
need to be replaced soon.
Printing in ink-backup mode

Solution: If you receive the ink-backup mode message and two print cartridges are
installed in the product, verify that the protective piece of plastic tape has been
removed from each print cartridge. When plastic tape covers the print cartridge
contacts, the device cannot detect that the print cartridge is installed.
For more information, see Use ink-backup mode.

Cause: When the product detected that only one print cartridge is installed, ink-
backup mode is initiated. This printing mode lets you print with a single print cartridge,
but it slows the product and affects the quality of printouts.
184 Troubleshooting
• Solution 1: Print a self-test report
• Solution 2: Clear the print carriage
Troubleshooting
• Solution 3: Check the power source
Solution 1: Print a self-test report

Solution: Print a self-test report to see if the product can print.

complete.
a problem with the black or photo print cartridge in the right slot.
Cause: The error was false.

Chapter 12
Solution 2: Clear the print carriage

Solution: Remove any objects, such as paper, that are blocking the print carriage.
Then reset the product.
To clear the print carriage

1. Make sure the product is on.
Troubleshooting

The print carriage should move to the center of the product. If the print carriage
does not move to the center, turn the product off, and then on.
3. Make note of where the print carriage is stuck and look for jammed paper.
A paper jam can cause the error message and the print carriage to stall.
CAUTION: Do not use any tools or other devices to remove jammed paper.
Always use caution when removing jammed paper from inside the product.
If the print carriage is stuck on the right side

a. Check for any paper or object that might be restricting the print carriage.
b. Move the print carriage all the way to the left side.
c. Check the paper path all the way to the right side and remove any paper still
in the product.
If the print carriage is stuck on the left side

a. Check for any paper or object that may be restricting the print carriage.
b. Move the print carriage all the way to the right side.
c. Check the paper path all the way to the left side and remove any paper still
in the product.
If the print carriage is stuck in the middle

a. Check for any paper or object that may be restricting the print carriage.
b. Move the print carriage all the way to the left side.
c. Check the paper path all the way to the right side and remove any paper still
in the product.
d. Move the print carriage all the way to the right side.
e. Check the paper path all the way to the left side and remove any paper still
in the product.
186 Troubleshooting
5. Check for a paper jam in the rear access door.
To check for a paper jam in the rear access door

a. Press in the tab on the rear access door to release the door. Remove the door
by pulling it away from the product.
Troubleshooting
b. Check for any paper still in the product. Gently pull any paper out of the rollers.
c. Replace the rear access door. Gently push the door forward until it snaps into
place.
6. Do one of the following, depending upon the state of the product:

• If the On button light is on and steady, print a self-test report. If you can print
a self-test report, the carriage is no longer jammed.
• If the On button light is not on or is flashing and the print carriage is still stalled,
proceed to the next solution.
7. Disconnect and reset the product.
To disconnect and reset the product

a. Make sure the product is turned on.
b. Press the On button to turn off the product.
c. Disconnect the power cord from the back of the product.
d. Reconnect the power cord to the back of the product.
e. Press the On to turn on the product.
Cause: The print carriage was blocked by a paper jam.

Chapter 12
Solution 3: Check the power source

Solution: Verify that the product is properly connected to a suitable power source.
To verify that the product is connected to a suitable power source

1. Verify that the product has a two-prong power plug, and make sure you are using
the power cord provided with the product.
Troubleshooting
2. If the product is connected to a computer, make sure the computer has the correct
power plug depending on your country/region.
adaptor.
4. Plug the power cord directly into a wall outlet.
1 Power connection
5. Try to print from your computer.

If the product prints when plugged directly into a wall outlet while disconnected
from any power strips or surge suppressors, the power strip or surge suppressor
might not be allowing sufficient voltage to reach the product.
6. If the product cannot print and the print carriage is still stalled, contact HP support
for service.
If prompted, choose your country/region, and then click Contact HP for
information on calling for technical support.
Cause: There might not be not be sufficient voltage for the product.
188 Troubleshooting
Need alignment or alignment failed
• Solution 1: Incorrect type of paper is loaded in the input tray
• Solution 2: Make sure the protective tape is removed from the print cartridges
• Solution 3: Check if print cartridges are fully inserted
Troubleshooting
• Solution 4: Align newly installed print cartridges
• Solution 5: Print cartridge or sensor might be defective
Solution 1: Incorrect type of paper is loaded in the input tray

Solution: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment fails. Load unused plain white letter or A4 paper into the
input tray, and then try the alignment again. If the alignment fails again, you might
have a defective sensor or print cartridge.
To find support and warranty information, go to the HP Web site at www.hp.com/
support. If prompted, choose your country/region, and then click Contact HP for
Cause: Incorrect type of paper was loaded in the input tray.
Solution 2: Make sure the protective tape is removed from the print cartridges
Solution: Check each print cartridge. The tape might have been removed from the
copper-colored contacts, but still might cover the ink nozzles. If the tape is still
covering the ink nozzles, carefully remove the tape from the print cartridges. Do not
touch the ink nozzles or the copper-colored contacts.

Chapter 12
Remove and then reinsert the print cartridges. Verify that they are fully inserted and
locked in place.
Cause: Protective tape was covering the print cartridges.
Troubleshooting
Solution 3: Check if print cartridges are fully inserted

Solution: Remove and then reinsert the print cartridges. Verify that they are fully
inserted and locked in place.
Cause: The contacts on the print cartridge were not touching the contacts in the
print carriage.
Solution 4: Align newly installed print cartridges

Solution: You must align the print cartridges to ensure excellent print quality.
If the alignment error persists and you cannot clear it , your print cartridge might be
defective. Contact HP for support.
To find support and warranty information, go to the HP Web site at www.hp.com/
support. If prompted, choose your country/region, and then click Contact HP for
Align the print cartridges
Cause: You installed new print cartridges that needed alignment
Solution 5: Print cartridge or sensor might be defective

Cause: The print cartridge or sensor was defective.
Print cartridge is missing, incorrectly installed, or not intended for your product
Solution: If the print cartridges are missing, incorrectly installed, or not intended for
your product, one or both of the print cartridge status lights begin to blink. One of the
following messages may appear on your computer screen:
Print Cartridge Problem
Incorrect Print Cartridge(s)
Incorrectly Installed Cartridge(s)
190 Troubleshooting
Print Cartridge(s) Missing
For resolving these print cartridge error messages, see Resolving print cartridge error
messages.
Print cartridges missing or not detected
Troubleshooting
• Solution 1: Remove and reinsert the print cartridges
• Solution 3: Replace the print cartridges
Solution 1: Remove and reinsert the print cartridges

Solution: Remove and reinsert the print cartridges and verify that they are fully
Also, make sure the print cartridges are installed into the correct slots.
To make sure the print cartridges are installed correctly

CAUTION: If the HP All-in-One is off when you open the print cartridge door
to access the print cartridges, the HP All-in-One will not release the cartridges
for changing. You might damage the HP All-in-One if the print cartridges are
not docked safely when you try to remove them.

3. Check to make sure you are using the correct print cartridges for your product.
For a list of compatible print cartridges, see the printed documentation that came
with the product.

Chapter 12
4. Remove the black print cartridge from the slot on the right. Do not touch the ink
nozzles or the copper-colored contacts. Check for possible damage to the copper-
colored contacts or ink nozzles.
Make sure the clear plastic tape has been removed. If it is still covering the ink
nozzles, gently remove the clear plastic tape by using the pink pull tab. Make sure
you do not remove the copper colored tape containing the electrical contacts.
Troubleshooting
5. Reinsert the print cartridge by sliding it forward into the slot on the right. Then
push the print cartridge forward until it clicks into the socket.
6. Repeat steps 1 and 2 for the tri-color print cartridge on the left side.
Cause: The indicated print cartridges were installed incorrectly.

Solution: Clean the print cartridge contacts.
192 Troubleshooting
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart
or leave fibers.
Troubleshooting

3. Lightly press down on the print cartridge to release it, and then pull it toward you
out of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and
clean each print cartridge one at a time. Do not leave a print cartridge outside
the HP All-in-One for more than 30 minutes.
5. Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze
any excess water from it.

Chapter 12
Troubleshooting
into the slot. Make sure you push the print cartridge in firmly until it snaps into
place.

product.
Cause: The print cartridge contacts needed to be cleaned.

194 Troubleshooting
Solution 3: Replace the print cartridges
Solution: Replace the indicated print cartridge. You can also remove the indicated
print cartridge and print using ink-backup mode.
NOTE: During ink-backup mode, the product can only print jobs from the
computer. You cannot initiate a print job from the control panel (such as printing
a photo from a memory card).
Troubleshooting
Check to see if your print cartridge is still under warranty and end of warranty date
has not been reached.
• If the end of warranty date has been reached, purchase a new print cartridge.
• If the end of warranty date has not been reached, contact HP support. Go to
Related topics
Cause: The print cartridge was damaged.
Incompatible print cartridges

• Solution 1: Make sure you are using the correct print cartridges
• Solution 2: Contact HP customer support
Solution 1: Make sure you are using the correct print cartridges
Solution: Check to make sure you are using the correct print cartridges for your
product. For a list of compatible print cartridges, see the printed documentation that
came with the product.
If you are using print cartridges that are not compatible with the product, replace the
indicated print cartridges with print cartridges that are compatible.
If it appears that you are using the correct print cartridges, proceed to the next
solution.
• Shop for ink supplies
Cause: The indicated print cartridges were not compatible with the product.

Chapter 12
Solution 2: Contact HP customer support

Cause: The print cartridges were not intended for use in this product.
Troubleshooting
Print cartridges in wrong slot

Solution: Make sure the print cartridges are installed into the correct slots. If they
are, remove and reinsert the print cartridges and verify that they are fully inserted and
locked in place.


196 Troubleshooting
with the product.
Troubleshooting
NOTE: If the print cartridges are installed in the wrong slots and you cannot
remove them from the product, contact HP support for service.
If prompted, choose your country/region, and then click Contact HP for

Chapter 12
Print cartridge problem

The message might indicate which cartridge is causing the problem. If so, try the following
solutions to resolve the issue. Solutions are listed in order, with the most likely solution
first. If the first solution does not solve the problem, continue trying the remaining solutions
until the issue is resolved.
If the message does not indicate which cartridge is causing the problem, follow these
steps to determine which cartridge is the problem cartridge. After you determine which
Troubleshooting
cartridge is the problem cartridge, continue with the first solution.
To determine which print cartridge is having the problem

CAUTION: If the product is turned off when you open the print cartridge door to
access the print cartridges, it will not release the cartridges for changing. You
might damage the product if the print cartridges are not docked safely when you
try to remove them.

The print carriage moves to the far right side of the product.
3. Check to make sure you are using the correct print cartridges for your product. For a
list of compatible print cartridges, see the printed documentation that came with the
product.
4. Remove the black print cartridge from the slot on the right.
Press down on the cartridge to release it, and then pull it toward you out of the slot.
1 Tri-color print cartridge

2 Black print cartridge
198 Troubleshooting
6. Check to see if the error has been resolved.
• If the error has been resolved, then there is a problem with the black print
cartridge.
• If the error has not been resolved, continue to the next step.
7. Open the print cartridge door and reinsert the black print cartridge by sliding it forward
into the slot on the right. Then push the print cartridge forward until it clicks into the
Troubleshooting
slot.
8. Remove the tri-color print cartridge from the slot on the left.
Press down on the cartridge to release it, and then pull it toward you out of the slot.
10. Check to see if the error has been resolved.
• If the error has been resolved, then there is a problem with the tri-color print
cartridge.
• If the error has not been resolved, then there is a problem with both print
cartridges.
11. Open the print cartridge door and reinsert the tri-color print cartridge by sliding it
forward into the slot on the left. Then push the print cartridge forward until it clicks into
the slot.
• Solution 1: Remove and reinsert the print cartridges
• Solution 3: Replace the print cartridges
Solution 1: Remove and reinsert the print cartridges

Solution: Remove and reinsert the print cartridges and verify that they are fully

Chapter 12
Also, make sure the print cartridges are installed into the correct slots.

Troubleshooting

with the product.
200 Troubleshooting
Troubleshooting

Solution: Clean the print cartridge contacts on the print carridge(s) that are
experiencing the problem.
• Dry foam rubber swabs, lint-free cloth, or any soft material that will not come apart
or leave fibers.


Chapter 12
3. Lightly press down on the print cartridge to release it, and then pull it toward you
out of the slot.
NOTE: Do not remove both print cartridges at the same time. Remove and
clean each print cartridge one at a time. Do not leave a print cartridge outside
Troubleshooting
the HP All-in-One for more than 30 minutes.
5. Dip a clean foam rubber swab or lint-free cloth into distilled water, and squeeze
any excess water from it.
into the slot. Make sure you push the print cartridge in firmly until it snaps into
place.
202 Troubleshooting
product.
Troubleshooting
Cause: The print cartridge contacts needed to be cleaned.
Solution 3: Replace the print cartridges

Solution: Replace the print cartridges that are experiencing the problem. If only one
of the print cartridges is experiencing the problem, you can also remove it and print
using ink-backup mode.
NOTE: During ink-backup mode, the product can only print jobs from the
computer. You cannot initiate a print job from the control panel (such as copying
or scanning an original). For more information, see Use ink-backup mode.
Cause: One or both of the print cartridges were having a problem.

Chapter 12
Troubleshooting
204 Troubleshooting
13 HP warranty and support
Hewlett-Packard provides Internet and phone support for the HP All-in-One.
• Warranty
• Print cartridge warranty information
• Support process
• Before you call HP customer support
• HP support by phone
• Additional warranty options
• HP Quick Exchange Service (Japan)
• HP Korea customer support
• Prepare the product for shipment
• Pack the product
HP warranty and support

Warranty
For more information about the warranty, see the printed documentation that came with the product.
Print cartridge warranty information

The HP cartridge warranty is applicable when the product is used in its designated HP printing device.
This warranty does not cover HP ink products that have been refilled, remanufactured, refurbished,
misused, or tampered with.
During the warranty period the product is covered as long as the HP ink is not depleted and the end
of warranty date has not been reached. The end of warranty date, in YYYY/MM/DD format, may be
found on the product as indicated:
For a copy of the HP Limited Warranty Statement, see the printed documentation that came with the
product.
Support process
If you have a problem, follow these steps:
1. Check the documentation that came with the product.
2. Visit the HP online support Web site at www.hp.com/support. HP online support is available to
all HP customers. It is the fastest source for up-to-date product information and expert
assistance and includes the following features:
• Fast access to qualified online support specialists
• Software and driver updates for the product
Downloaded from ManualsPrinter.com Manuals HP warranty and support 205

Chapter 13
• Valuable product and troubleshooting information for common problems

• Proactive product updates, support alerts, and HP newsgrams that are available when you
register the product
3. Call HP support. Support options and availability vary by product, country/region, and language.
Before you call HP customer support

Software programs from other companies might be included with the HP All-in-One. If you experience
problems with any of those programs, you will receive the best technical assistance by calling the
experts at that company.
If you need to contact HP support, do the following before you call:

1. Make sure that:
a. The product is plugged in and turned on.
b. The specified print cartridges are installed correctly.
c. The recommended paper is properly loaded in the input tray.
2. Reset the product:
a. Turn off the product by pressing the On button.
b. Unplug the power cord from the back of the product.

c. Plug the power cord back into the product.
d. Turn on the product by pressing the On button.
3. To find support and warranty information, go to the HP Web site at www.hp.com/support. If
prompted, choose your country/region, and then click Contact HP for information on calling for
technical support.
Check the HP Web site for updated information or troubleshooting tips for the product.
4. If you are still experiencing problems and need to speak with an HP support representative, do
the following:
a. Have the specific name of the product, as it appears on the control panel, available.
b. Print a self-test report.
c. Make a color copy to have available as a sample printout.
d. Be prepared to describe your problem in detail.
e. Have your serial number ready.
You can view the serial number by looking at the sticker on the rear side of the product. The
serial number is the 10-character code in the upper left corner of the sticker.
5. Call HP support. Be near the product when you call.
Related topics
• Placing a call
HP support by phone
For a list of support phone numbers, see the printed documentation that came with the device.
• Phone support period
• Placing a call
• After the phone support period
Phone support period

One year of phone support is available in North America, Asia Pacific, and Latin America (including
Mexico). To determine the duration of phone support in Europe, the Middle East, and Africa, go to
www.hp.com/support. Standard phone company charges apply.
206 HP warranty
Downloaded and support
Placing a call
Call HP support while you are in front of the computer and the product. Be prepared to provide the
following information:
• Model number (located on the label on the front of the product)
• Serial number (located on the back or bottom of the product)
• Messages that appear when the situation occurs
• Answers to these questions:
• Has this situation happened before?
• Can you re-create it?
• Did you add any new hardware or software to your computer at about the time that this
situation began?
• Did anything else occur prior to this situation (such as a thunderstorm, product was moved,
etc.)?
After the phone support period

After the phone support period, help is available from HP at an additional cost. Help may also be
available at the HP online support Web site: www.hp.com/support. Contact your HP dealer or call

the support phone number for your country/region to learn more about support options.
Additional warranty options

Extended service plans are available for the HP All-in-One at additional costs. Go to www.hp.com/
support, select your country/region and language, then explore the services and warranty area for
information about the extended service plans.
Downloaded from ManualsPrinter.com Manuals Additional warranty options 207

Chapter 13
HP Quick Exchange Service (Japan)

For instructions on how to pack your product for exchange, see Pack the product.
HP Korea customer support
208 HP warranty
Prepare the product for shipment
If after contacting HP Customer Support or returning to the point of purchase you are requested to
send the product in for service, make sure you remove and keep the following items before returning
your product:
• The print cartridges
• The power cord, USB cable, and any other cable connected to the HP All-in-One
• Any paper loaded in the input tray
• Any originals loaded in the HP All-in-One
To remove print cartridges before shipment
1. Turn on the product and wait until the print carriage is idle and silent. If the product will not turn
on, skip this step and go to step 2.
3. Remove the print cartridges from their slots.
NOTE: If the product does not turn on, you can unplug the power cord and then manually
slide the print carriage to the center to remove the print cartridges.

4. Place the print cartridges in an airtight plastic container so they will not dry out, and put them
aside. Do not send them with the product unless the HP customer support call agent instructs
you to.
5. Close the print cartridge door and wait a few minutes for the print carriage to move back to its
home position (on the left side).
NOTE: Make sure the scanner is idle and has returned to its parked position before turning
off the product.
6. Press the On button to turn off the product.
Pack the product

Complete the following steps once you have removed the print cartridges, turned off the product,
and unplugged it.
To pack the product
1. If available, pack the product for shipment by using the original packing materials or the
packaging materials that came with your exchange product.
Downloaded from ManualsPrinter.com Manuals Prepare the product for shipment 209
Chapter 13
If you do not have the original packaging materials, please use other adequate packaging
materials. Shipping damage caused by improper packaging and/or improper transportation is
not covered under the warranty.
2. Place the return shipping label on the outside of the box.
3. Include the following items in the box:
• A complete description of symptoms for service personnel (samples of print quality problems
are helpful).
• A copy of the sales slip or other proof of purchase to establish the warranty coverage period.
• Your name, address, and a phone number where you can be reached during the day.
210 HP warranty
14 Technical information
The technical specifications and international regulatory information for the HP All-in-One are
provided in this section.
For additional specifications, see the printed documentation that came with the HP All-in-One.
• Specifications
• Notice to Windows 2000 users
• Environmental product stewardship program
• Regulatory notices
Specifications
Technical specifications for the HP All-in-One are provided in this section. For additional
specifications, see the printed Basics Guide.
System requirements
Software and system requirements are located in the Readme file.
For information about future operating system releases and support, visit the HP online support Web
site at www.hp.com/support.
Paper tray capacities
Type Paper weight Paper tray* Output tray†
Plain paper 75 to 90 gsm (20 to 24 Up to 80 (75 gsm (20 lb.) 50 (75 gsm (20 lb.)
lb.) paper) paper)
Legal paper 75 to 90 gsm (20 to 24 Up to 80 (75 gsm (20 lb.) 50 (75 gsm (20 lb.)
lb.) paper) paper)
Cards 200 gsm (110 lb.) index Up to 40 25

max
Technical information
Envelopes 75 to 90 gsm (20 to 24 Up to 10 10
lb.)
Transparency film N/A Up to 30 15 or fewer
Labels N/A Up to 30 25
10 x 15 cm (4 x 6 in.) Photo 236 gsm (145 lb.) Up to 30 25

paper
216 x 279 mm (8.5 x 11 in.) N/A Up to 30 10

Photo paper
* Maximum capacity.
† Output tray capacity is affected by the type of paper and the amount of ink you are using.
HP recommends emptying the output tray frequently.
Copy specifications
• Digital image processing
• Up to 9 copies from original (depends on model)
• Copy speeds vary according to the complexity of the document and model
Downloaded from ManualsPrinter.com Manuals Technical information 211

Chapter 14
• Maximum copy enlargement ranging from 200-400% (depends on model)

• Maximum copy reduction ranging from 25-50% (depends on model)
Scan specifications
• Image editor included
• Integrated OCR software automatically converts scanned text to editable text (if installed)
• Twain-compliant software interface
• Resolution: up to 1200 x 2400 ppi optical (depends on model); 19200 ppi enhanced (software)
For more information about ppi resolution, see the scanner software.
• Color: 48-bit color, 8-bit grayscale (256 levels of gray)
• Maximum scan size from glass: 21.6 x 29.7 cm (8.5 x 11.7 inches)
Print resolution
To find out about the printer resolution, see the printer software. For more information, see View the
print resolution.
Print cartridge yield

Visit www.hp.com/pageyield for more information on estimated cartridge yields.
Acoustic information
If you have Internet access, you can get acoustic information from the HP Web site. Go to:
www.hp.com/support.
Notice to Windows 2000 users

This product provides limited functionality for Windows 2000, including but not limited to the following:
• Scanning is supported using TWAIN or WIA in a software application only. The Scan button on
the control panel will not work.
• Copying is supported from the control panel only.
• The HP Photosmart Software is not available.
• The onscreen Help is not installed, but it is available as a Web download at www.hp.com/
support.
Environmental product stewardship program

Hewlett-Packard is committed to providing quality products in an environmentally sound manner.
Design for recycling has been incorporated into this product. The number of materials has been kept
to a minimum while ensuring proper functionality and reliability. Dissimilar materials have been
designed to separate easily. Fasteners and other connections are easy to locate, access, and
remove using common tools. High priority parts have been designed to access quickly for efficient
disassembly and repair.
For more information, visit HP’s Commitment to the Environment Web site at:
www.hp.com/hpinfo/globalcitizenship/environment/index.html
• Paper use
• Plastics
• Material safety data sheets
• Recycling program
• HP inkjet supplies recycling program
• Energy Star® notice
• Disposal of waste equipment by users in private households in the European Union
212 Technical
Paper use
This product is suited for the use of recycled paper according to DIN 19309 and EN 12281:2002.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability
to identify plastics for recycling purposes at the end of product life.
Material safety data sheets

Material safety data sheets (MSDS) can be obtained from the HP Web site at:
www.hp.com/go/msds
Recycling program
HP offers an increasing number of product return and recycling programs in many countries/regions,
and partners with some of the largest electronic recycling centers throughout the world. HP
conserves resources by reselling some of its most popular products. For more information regarding
recycling of HP products, please visit:
www.hp.com/hpinfo/globalcitizenship/environment/recycle/
HP inkjet supplies recycling program

HP is committed to protecting the environment. The HP Inkjet Supplies Recycling Program is
available in many countries/regions, and lets you recycle used print cartridges and ink cartridges
free of charge. For more information, go to the following Web site:
www.hp.com/hpinfo/globalcitizenship/environment/recycle/
Energy Star® notice

This product is designed to reduce power consumption and save natural resources without
compromising product performance. It has been designed to reduce total energy consumption both
during operation and when the device is not active. This product qualifies for ENERGY STAR® which
is a voluntary program established to encourage the development of energy-efficient office products.
ENERGY STAR is a U.S. registered service mark of the U.S. EPA. As an ENERGY STAR partner,
HP has determined that this product meets ENERGY STAR guidelines for energy efficiency.
For more information on ENERGY STAR guidelines, go to the following Web site:
www.energystar.gov
Downloaded from ManualsPrinter.com Manuals Environmental product stewardship program 213

Chapter 14
Disposal of waste equipment by users in private households in the European Union
Disposal of Waste Equipment by Users in Private Households in the European Union

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste
English
equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment
at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where
you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
Évacuation des équipements usagés par les utilisateurs dans les foyers privés au sein de l'Union européenne
La présence de ce symbole sur le produit ou sur son emballage indique que vous ne pouvez pas vous débarrasser de ce produit de la même façon que vos déchets courants.
Français
Au contraire, vous êtes responsable de l'évacuation de vos équipements usagés et, à cet effet, vous êtes tenu de les remettre à un point de collecte agréé pour le recyclage des
équipements électriques et électroniques usagés. Le tri, l'évacuation et le recyclage séparés de vos équipements usagés permettent de préserver les ressources naturelles et de s'assurer
que ces équipements sont recyclés dans le respect de la santé humaine et de l'environnement. Pour plus d'informations sur les lieux de collecte des équipements usagés, veuillez contacter
votre mairie, votre service de traitement des déchets ménagers ou le magasin où vous avez acheté le produit.
Entsorgung von Elektrogeräten durch Benutzer in privaten Haushalten in der EU
Dieses Symbol auf dem Produkt oder dessen Verpackung gibt an, dass das Produkt nicht zusammen mit dem Restmüll entsorgt werden darf. Es obliegt daher Ihrer Verantwortung, das
Deutsch
Gerät an einer entsprechenden Stelle für die Entsorgung oder Wiederverwertung von Elektrogeräten aller Art abzugeben (z.B. ein Wertstoffhof). Die separate Sammlung und das
Recyceln Ihrer alten Elektrogeräte zum Zeitpunkt ihrer Entsorgung trägt zum Schutz der Umwelt bei und gewährleistet, dass sie auf eine Art und Weise recycelt werden, die keine
Gefährdung für die Gesundheit des Menschen und der Umwelt darstellt. Weitere Informationen darüber, wo Sie alte Elektrogeräte zum Recyceln abgeben können, erhalten Sie bei
den örtlichen Behörden, Wertstoffhöfen oder dort, wo Sie das Gerät erworben haben.
Smaltimento di apparecchiature da rottamare da parte di privati nell'Unione Europea
Questo simbolo che appare sul prodotto o sulla confezione indica che il prodotto non deve essere smaltito assieme agli altri rifiuti domestici. Gli utenti devono provvedere allo
Italiano
smaltimento delle apparecchiature da rottamare portandole al luogo di raccolta indicato per il riciclaggio delle apparecchiature elettriche ed elettroniche. La raccolta e il riciclaggio
separati delle apparecchiature da rottamare in fase di smaltimento favoriscono la conservazione delle risorse naturali e garantiscono che tali apparecchiature vengano rottamate
nel rispetto dell'ambiente e della tutela della salute. Per ulteriori informazioni sui punti di raccolta delle apparecchiature da rottamare, contattare il proprio comune di residenza,
il servizio di smaltimento dei rifiuti locale o il negozio presso il quale è stato acquistato il prodotto.
Eliminación de residuos de aparatos eléctricos y electrónicos por parte de usuarios domésticos en la Unión Europea
Este símbolo en el producto o en el embalaje indica que no se puede desechar el producto junto con los residuos domésticos. Por el contrario, si debe eliminar este tipo de residuo, es
Español
responsabilidad del usuario entregarlo en un punto de recogida designado de reciclado de aparatos electrónicos y eléctricos. El reciclaje y la recogida por separado de estos residuos
en el momento de la eliminación ayudará a preservar recursos naturales y a garantizar que el reciclaje proteja la salud y el medio ambiente. Si desea información adicional sobre los
lugares donde puede dejar estos residuos para su reciclado, póngase en contacto con las autoridades locales de su ciudad, con el servicio de gestión de residuos domésticos o con la
tienda donde adquirió el producto.
Likvidace vysloužilého zařízení uživateli v domácnosti v zemích EU
Tato značka na produktu nebo na jeho obalu označuje, že tento produkt nesmí být likvidován prostým vyhozením do běžného domovního odpadu. Odpovídáte za to, že vysloužilé
Česky
zařízení bude předáno k likvidaci do stanovených sběrných míst určených k recyklaci vysloužilých elektrických a elektronických zařízení. Likvidace vysloužilého zařízení samostatným
sběrem a recyklací napomáhá zachování přírodních zdrojů a zajišťuje, že recyklace proběhne způsobem chránícím lidské zdraví a životní prostředí. Další informace o tom, kam můžete
vysloužilé zařízení předat k recyklaci, můžete získat od úřadů místní samosprávy, od společnosti provádějící svoz a likvidaci domovního odpadu nebo v obchodě, kde jste produkt
zakoupili.
Bortskaffelse af affaldsudstyr for brugere i private husholdninger i EU
Dette symbol på produktet eller på dets emballage indikerer, at produktet ikke må bortskaffes sammen med andet husholdningsaffald. I stedet er det dit ansvar at bortskaffe affaldsudstyr
Dansk
ved at aflevere det på dertil beregnede indsamlingssteder med henblik på genbrug af elektrisk og elektronisk affaldsudstyr. Den separate indsamling og genbrug af dit affaldsudstyr på
tidspunktet for bortskaffelse er med til at bevare naturlige ressourcer og sikre, at genbrug finder sted på en måde, der beskytter menneskers helbred samt miljøet. Hvis du vil vide mere
om, hvor du kan aflevere dit affaldsudstyr til genbrug, kan du kontakte kommunen, det lokale renovationsvæsen eller den forretning, hvor du købte produktet.
Afvoer van afgedankte apparatuur door gebruikers in particuliere huishoudens in de Europese Unie
Nederlands
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden afgevoerd met het huishoudelijk afval. Het is uw verantwoordelijkheid uw afgedankte apparatuur
af te leveren op een aangewezen inzamelpunt voor de verwerking van afgedankte elektrische en elektronische apparatuur. De gescheiden inzameling en verwerking van uw afgedankte
apparatuur draagt bij tot het sparen van natuurlijke bronnen en tot het hergebruik van materiaal op een wijze die de volksgezondheid en het milieu beschermt. Voor meer informatie over
waar u uw afgedankte apparatuur kunt inleveren voor recycling kunt u contact opnemen met het gemeentehuis in uw woonplaats, de reinigingsdienst of de winkel waar u het product
hebt aangeschaft.
Eramajapidamistes kasutuselt kõrvaldatavate seadmete käitlemine Euroopa Liidus
Kui tootel või toote pakendil on see sümbol, ei tohi seda toodet visata olmejäätmete hulka. Teie kohus on viia tarbetuks muutunud seade selleks ettenähtud elektri- ja elektroonikaseadmete
Eesti
utiliseerimiskohta. Utiliseeritavate seadmete eraldi kogumine ja käitlemine aitab säästa loodusvarasid ning tagada, et käitlemine toimub inimeste tervisele ja keskkonnale ohutult.
Lisateavet selle kohta, kuhu saate utiliseeritava seadme käitlemiseks viia, saate küsida kohalikust omavalitsusest, olmejäätmete utiliseerimispunktist või kauplusest, kust te seadme
ostsite.
Hävitettävien laitteiden käsittely kotitalouksissa Euroopan unionin alueella
Tämä tuotteessa tai sen pakkauksessa oleva merkintä osoittaa, että tuotetta ei saa hävittää talousjätteiden mukana. Käyttäjän velvollisuus on huolehtia siitä, että hävitettävä laite
Suomi
toimitetaan sähkö- ja elektroniikkalaiteromun keräyspisteeseen. Hävitettävien laitteiden erillinen keräys ja kierrätys säästää luonnonvaroja. Näin toimimalla varmistetaan myös,
että kierrätys tapahtuu tavalla, joka suojelee ihmisten terveyttä ja ympäristöä. Saat tarvittaessa lisätietoja jätteiden kierrätyspaikoista paikallisilta viranomaisilta, jäteyhtiöiltä tai tuotteen
jälleenmyyjältä.
Απόρριψη άχρηστων συσκευών στην Ευρωπαϊκή Ένωση
Το παρόν σύμβολο στον εξοπλισμό ή στη συσκευασία του υποδεικνύει ότι το προϊόν αυτό δεν πρέπει να πεταχτεί μαζί με άλλα οικιακά απορρίμματα. Αντίθετα, ευθύνη σας είναι να
Ελληνικά
απορρίψετε τις άχρηστες συσκευές σε μια καθορισμένη μονάδα συλλογής απορριμμάτων για την ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού. Η χωριστή συλλογή και
ανακύκλωση των άχρηστων συσκευών θα συμβάλει στη διατήρηση των φυσικών πόρων και στη διασφάλιση ότι θα ανακυκλωθούν με τέτοιον τρόπο, ώστε να προστατεύεται η υγεία των
ανθρώπων και το περιβάλλον. Για περισσότερες πληροφορίες σχετικά με το πού μπορείτε να απορρίψετε τις άχρηστες συσκευές για ανακύκλωση, επικοινωνήστε με τις κατά τόπους αρμόδιες
αρχές ή με το κατάστημα από το οποίο αγοράσατε το προϊόν.
A hulladékanyagok kezelése a magánháztartásokban az Európai Unióban
Ez a szimbólum, amely a terméken vagy annak csomagolásán van feltüntetve, azt jelzi, hogy a termék nem kezelhető együtt az egyéb háztartási hulladékkal. Az Ön feladata,
Magyar
hogy a készülék hulladékanyagait eljuttassa olyan kijelölt gyűjtőhelyre, amely az elektromos hulladékanyagok és az elektronikus berendezések újrahasznosításával foglalkozik.
A hulladékanyagok elkülönített gyűjtése és újrahasznosítása hozzájárul a természeti erőforrások megőrzéséhez, egyúttal azt is biztosítja, hogy a hulladék újrahasznosítása az
egészségre és a környezetre nem ártalmas módon történik. Ha tájékoztatást szeretne kapni azokról a helyekről, ahol leadhatja újrahasznosításra a hulladékanyagokat, forduljon
a helyi önkormányzathoz, a háztartási hulladék begyűjtésével foglalkozó vállalathoz vagy a termék forgalmazójához.
Lietotāju atbrīvošanās no nederīgām ierīcēm Eiropas Savienības privātajās mājsaimniecībās
Latviski
Šis simbols uz ierīces vai tās iepakojuma norāda, ka šo ierīci nedrīkst izmest kopā ar pārējiem mājsaimniecības atkritumiem. Jūs esat atbildīgs par atbrīvošanos no nederīgās ierīces,
to nododot norādītajā savākšanas vietā, lai tiktu veikta nederīgā elektriskā un elektroniskā aprīkojuma otrreizējā pārstrāde. Speciāla nederīgās ierīces savākšana un otrreizējā pārstrāde
palīdz taupīt dabas resursus un nodrošina tādu otrreizējo pārstrādi, kas sargā cilvēku veselību un apkārtējo vidi. Lai iegūtu papildu informāciju par to, kur otrreizējai pārstrādei var
nogādāt nederīgo ierīci, lūdzu, sazinieties ar vietējo pašvaldību, mājsaimniecības atkritumu savākšanas dienestu vai veikalu, kurā iegādājāties šo ierīci.
Europos Sąjungos vartotojų ir privačių namų ūkių atliekamos įrangos išmetimas
Lietuviškai
Šis simbolis ant produkto arba jo pakuotės nurodo, kad produktas negali būti išmestas kartu su kitomis namų ūkio atliekomis. Jūs privalote išmesti savo atliekamą įrangą atiduodami ją
į atliekamos elektronikos ir elektros įrangos perdirbimo punktus. Jei atliekama įranga bus atskirai surenkama ir perdirbama, bus išsaugomi natūralūs ištekliai ir užtikrinama, kad įranga
yra perdirbta žmogaus sveikatą ir gamtą tausojančiu būdu. Dėl informacijos apie tai, kur galite išmesti atliekamą perdirbti skirtą įrangą kreipkitės į atitinkamą vietos tarnybą, namų ūkio
atliekų išvežimo tarnybą arba į parduotuvę, kurioje pirkote produktą.
Utylizacja zużytego sprzętu przez użytkowników domowych w Unii Europejskiej
Polski
Symbol ten umieszczony na produkcie lub opakowaniu oznacza, że tego produktu nie należy wyrzucać razem z innymi odpadami domowymi. Użytkownik jest odpowiedzialny za
dostarczenie zużytego sprzętu do wyznaczonego punktu gromadzenia zużytych urządzeń elektrycznych i elektronicznych. Gromadzenie osobno i recykling tego typu odpadów
przyczynia się do ochrony zasobów naturalnych i jest bezpieczny dla zdrowia i środowiska naturalnego. Dalsze informacje na temat sposobu utylizacji zużytych urządzeń można
uzyskać u odpowiednich władz lokalnych, w przedsiębiorstwie zajmującym się usuwaniem odpadów lub w miejscu zakupu produktu.
Descarte de equipamentos por usuários em residências da União Européia
Português
Este símbolo no produto ou na embalagem indica que o produto não pode ser descartado junto com o lixo doméstico. No entanto, é sua responsabilidade levar os equipamentos
a serem descartados a um ponto de coleta designado para a reciclagem de equipamentos eletro-eletrônicos. A coleta separada e a reciclagem dos equipamentos no momento do
descarte ajudam na conservação dos recursos naturais e garantem que os equipamentos serão reciclados de forma a proteger a saúde das pessoas e o meio ambiente. Para obter mais
informações sobre onde descartar equipamentos para reciclagem, entre em contato com o escritório local de sua cidade, o serviço de limpeza pública de seu bairro ou a loja em que
adquiriu o produto.
Postup používateľov v krajinách Európskej únie pri vyhadzovaní zariadenia v domácom používaní do odpadu
Slovenčina
Tento symbol na produkte alebo na jeho obale znamená, že nesmie by vyhodený s iným komunálnym odpadom. Namiesto toho máte povinnos odovzda toto zariadenie na zbernom
mieste, kde sa zabezpečuje recyklácia elektrických a elektronických zariadení. Separovaný zber a recyklácia zariadenia určeného na odpad pomôže chráni prírodné zdroje a
zabezpečí taký spôsob recyklácie, ktorý bude chráni ľudské zdravie a životné prostredie. Ďalšie informácie o separovanom zbere a recyklácii získate na miestnom obecnom úrade,
vo firme zabezpečujúcej zber vášho komunálneho odpadu alebo v predajni, kde ste produkt kúpili.
Ravnanje z odpadno opremo v gospodinjstvih znotraj Evropske unije
Slovenščina
Ta znak na izdelku ali embalaži izdelka pomeni, da izdelka ne smete odlagati skupaj z drugimi gospodinjskimi odpadki. Odpadno opremo ste dolžni oddati na določenem zbirnem
mestu za recikliranje odpadne električne in elektronske opreme. Z ločenim zbiranjem in recikliranjem odpadne opreme ob odlaganju boste pomagali ohraniti naravne vire in zagotovili,
da bo odpadna oprema reciklirana tako, da se varuje zdravje ljudi in okolje. Več informacij o mestih, kjer lahko oddate odpadno opremo za recikliranje, lahko dobite na občini,
v komunalnem podjetju ali trgovini, kjer ste izdelek kupili.
Kassering av förbrukningsmaterial, för hem- och privatanvändare i EU
Svenska
Produkter eller produktförpackningar med den här symbolen får inte kasseras med vanligt hushållsavfall. I stället har du ansvar för att produkten lämnas till en behörig återvinningsstation
för hantering av el- och elektronikprodukter. Genom att lämna kasserade produkter till återvinning hjälper du till att bevara våra gemensamma naturresurser. Dessutom skyddas både
människor och miljön när produkter återvinns på rätt sätt. Kommunala myndigheter, sophanteringsföretag eller butiken där varan köptes kan ge mer information om var du lämnar
kasserade produkter för återvinning.
Изхвърляне на оборудване за отпадъци от потребители в частни домакинства в Европейския съюз
Български
Този символ върху продукта или опаковката му показва, чепродуктът не трябва да се изхвърля заедно с домакинските отпадъци. Вие имате отговорността да изхвърлите
оборудването за отпадъци, като го предадете на определен пункт за рециклиране на електрическо или механично оборудване за отпадъци. Отделното събиране и рециклиране
на оборудването за отпадъци при изхвърлянето му помага за запазването на природни ресурси и гарантира рециклиране, извършено така, чеда не застрашава човешкото
здраве и околната среда. За повече информация къде можете да оставите оборудването за отпадъци за рециклиране се свържете със съответния офис в града ви, фирмата за
събиране на отпадъци или смагазина, от който сте закупили продукта
Înlăturarea echipamentelor uzate de către utilizatorii casnici din Uniunea Europeană
Română
Acest simbol de pe produs sau de pe ambalajul produsului indică faptul că acest produs nu trebuie aruncat alături de celelalte deşeuri casnice. În loc să procedaţi astfel, aveţi
responsabilitatea să vă debarasaţi de echipamentul uzat predându-l la un centru de colectare desemnat pentru reciclarea deşeurilor electrice şi aechipamentelor electronice.
Colectarea şi reciclarea separată aechipamentului uzat atunci când doriţi să îl aruncaţi ajută la conservarea resurselor naturale şi asigură reciclarea echipamentului într-o manieră care
protejează sănătatea umană şi mediul. Pentru informaţii suplimentare despre locul în care se poate preda echipamentul uzat pentru reciclare, luaţi legătura cu primăria locală, cu
serviciul de salubritate sau cu vânzătorul de la care aţi achiziţionat produsul.
214 Technical
Regulatory notices
The HP All-in-One meets product requirements from regulatory agencies in your country/region.
• FCC statement
• Notice to users in Korea
• VCCI (Class B) compliance statement for users in Japan
• Notice to users in Japan about the power cord
• Noise emission statement for Germany
• Toxic and hazardous substance table
• HP Deskjet F2200 All-in-One series declaration of conformity
FCC statement
FCC statement
The United States Federal Communications Commission (in 47 CFR 15.105) has specified
that the following notice be brought to the attention of users of this product.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-
able protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For further information, contact:
Manager of Corporate Product Regulations
Hewlett-Packard Company
3000 Hanover Street
Palo Alto, Ca 94304
(650) 857-1501
Modifications (part 15.21)
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by HP may void the user's authority to operate the
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
Notice to users in Korea
Downloaded from ManualsPrinter.com Manuals Regulatory notices 215

Chapter 14
VCCI (Class B) compliance statement for users in Japan
Notice to users in Japan about the power cord
Noise emission statement for Germany
Geräuschemission
LpA < 70 dB am Arbeitsplatz im Normalbetrieb nach DIN 45635 T. 19
Toxic and hazardous substance table

216 Technical
HP Deskjet F2200 All-in-One series declaration of conformity
Downloaded from ManualsPrinter.com Manuals Regulatory notices 217

Chapter 14
218 Technical
Index
Symbols/Numerics print cartridge ink nozzle documents

10 x 15 cm photo paper area 77 edit scanned 61
load 26 print cartridges 74 scan 59
2 pages on 1, print 45 color double-sided prints 41, 42
4 pages on 1, print 45 dull 106
4 x 6 inch (10 x 15 cm) communication problems E
borderless photos test failed 180 edit
print 38 two-way communication scan preview 61
4 x 6 inch photo paper, load 26 lost 181 edit scanned images 61
connection problems enlargement 127
A device not found 180 envelopes
A4 paper, load 24 HP All-in-One will not turn load 28
addresses, print 48 on 84 environment
after the support period 207 connection types supported Environmental product
align print cartridges 73 printer sharing 19 stewardship program 212
alignment control panel error messages
failed 189 buttons 10, out of paper 175
print cartridges 189 copy reading or writing file 172
black-and-white
documents 56
B F
blank 127 fax
blank
borderless has borders 128 paper width incorrect 179
copy 127
borderless photo 56 poor quality printouts 102
scan 131
cancel 57 fax problems
booklet printing 42
make a copy 53 poor print quality 102
border 127
missing information 126 file
borderless copies 56
number of copies 55 invalid name 172
borderless photos
paper types, supported formats 173
copy has borders 128
recommended 53 unsupported formats 172
print 38
specifications 211 firmware revision mismatch 136
buttons, control panel 10
speed 54
troubleshooting 124
C crop G
cancel glass
fails 173
copy 57 clean 63
customer support
print job 50 greeting cards, load 29
contact 206
scan 62 warranty 205, 207
cancel button 11 H
cartridges. See print cartridges HP JetDirect 19
choose paper 21 D
HP Solution Center, missing
default printer, set as 32
clean icons 89
device
exterior 63
no response 113
glass 63 I
not found 180
lid backing 64 images
disconnected error 173
print cartridge contacts 75 edit scanned 61
scan 59
Index

improper shutdown 181 print cartridges 65 photo paper
ink replace print cartridges 67 load 26
drying time 174 self-test report 65 photos
low 122, 184 make a copy 53 edit scanned 61
sprays inside HP All-in- margins ink sprays 124
One 124 incorrect 119, 127 photo print cartridge 71
streaks on the back of text or graphic cut off 121 print borderless 38
paper 110 media. See paper print on photo paper 39
ink cartridges missing poor fax printout quality 102
HP ink depleted 183 information from copy 126 poor printout quality 99
ink levels, check 67 text from scan 132 portrait orientation 34
ink supplies posters 49
purchase 81 N preview image, edit 61
ink, removing ink from skin and no scan options error 174 preview print job 35
clothing 80 number of copies print
ink-backup mode 71 copy 55 2 or 4 pages on 1 45
install software, troubleshoot 83 addresses 48
invalid file name 172 blank printout 122
O
iron-on transfers 47 on button 10 booklet 42
order borderless fails 113
L ink supplies 81 borderless photos 38
labels print cartridges 81 both sides of page 41
load 29 out of paper 175 cancel job 50
landscape orientation 34 overheads, print 47 correct order 46
legal paper distorted printout 103
load 24 envelopes 48
P envelopes print
letter paper page order 46
load 24 incorrectly 112
paper
lid backing, clean 64 faded 106
choose 21
load from computer 31
feed fails 111
10 x 15 cm photo paper 26 from software application 31
incompatible types 23
4 x 6 inch photo paper 26 iron-on transfers 47
jam 136, 179
A4 paper 24 labels 48
jams 92
envelopes 28 margins incorrect 119, 121
load 24
full-size paper 24 meaningless characters 116
misfeed 179
greeting cards 29 multiple pages on one
out of 175
index cards 27 sheet 45
recommended copy
iron-on transfers 29 nothing happens 117
types 53
labels 29 on photo paper 39
recommended sizes for
legal paper 24 posters 49
printing 32
letter paper 24 preview 35
recommended types 22, 23
original 21 print options 32, 36
size incorrect 179
transparencies 29 quality, troubleshoot 99,
tips 93
102, 105, 108
type incorrect 179
resume job 51
M width incorrect 179
maintenance reverse images 47
paper tray capacities 211
align print cartridges 73 reversed page order 119
paper type 33
check ink levels 67 self-test report 65
phone numbers, customer
clean exterior 63 special print jobs 37
support 206
clean glass 63 transparencies 47
phone support 206
clean lid backing 64 troubleshooting 112
phone support period
clean print cartridges 74 vertical streaks 109
period for support 206
Web pages 49
Index
220
Index
print carriage R speed

stalled 185 Readme file 83 copy 54
print cartridge protector 72 recycle print 34
print cartridges ink cartridges 213 start copy
align 73, 189 regulatory notices 215 black 11
check ink levels 67 reinstall software 90 color 11
clean 74 removing ink from skin and status lights
clean contacts 75 clothing 80 overview 12
clean ink nozzle area 77 replace print cartridges 67 stop
damaged 191 reports copy 57
error message 190, 191 self-test 65 print job 50
handle 66 resolution scan 62
incorrect 190 print 34 support process 205
low ink 122 resume system requirements 211
low on ink 184 print job 51
missing 191 T
non-HP ink 183 S T-shirt transfers. See iron-on
order 81 scan transfers
part names 66 blank 131 technical information
photo print cartridge 71 cancel 62 copy specifications 211
previously used 183 crop incorrect 131 paper tray capacities 211
replace 67 documents 59 scan specifications 212
store 72 edit image 61 system requirements 211
tips 94 fails 129 telephone numbers, customer
print quality features 59 support 206
smeared ink 99 halts 129 text
print settings no scan options error 174 cut off 121
layout 34 page layout incorrect 131 dotted lines on scan 132
orientation 34 photos 59 incorrect format on
paper size 32 preview image, edit 61 scan 131
paper type 33 scan specifications 212 incorrect or missing on
print quality 98 stop 62 scan 132
quality 34 text appears as dotted jagged 111
reduce/enlarge 35 lines 132 meaningless characters 116
resizing options 35 text format incorrect 131 not filled in 102
resolution 34 text incorrect 132 smooth fonts 111
speed 34 troubleshooting 129 transparencies
printer sharing scan button 11 load 29
Mac 19 scan glass troubleshoot
Windows 19 clean 63 fax problems 102
printing self-test report 65 hardware installation 83
with one print cartridge 71 set print quality 99
Printing Shortcuts tab 36 print options 32, 36 Readme file 83
problems ship your product 209 software installation 87
copy 124 smeared ink 99 USB cable 85
error messages 133 software application, print troubleshooting
print 112 from 31 copy 124
scan 129 software installation error messages 133
reinstall 90 print 112
Q troubleshoot 87 scan 129
quality uninstall 90 two-sided prints 41, 42
print 34
Index

U
uninstall software 90
USB cable
communication lost 181
USB cable installation 85
W
warranty 205, 207
Web pages, print 49
Index
222

HP DeskJet F2280

Uploaded by

Copyright:

Available Formats

HP DeskJet F2280

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HP DeskJet F2280

Uploaded by

Copyright:

Available Formats

HP Deskjet F2200 All-in-One series

Downloaded from ManualsPrinter.com Manuals

Downloaded from ManualsPrinter.com Manuals

1 HP Deskjet F2200 All-in-One series Help...............................................................................7

3 Find more information............................................................................................................15

6 Load originals and load paper

7 Print from your computer

Downloaded from ManualsPrinter.com Manuals 1

Print a group of addresses on labels or envelopes............................................................48

8 Use the copy features

9 Use the scan features

10 Maintain the HP All-in-One

Work with print cartridges.........................................................................................................65

11 Shop for ink supplies.............................................................................................................81

Downloaded from ManualsPrinter.com Manuals 3

13 HP warranty and support

Notice to Windows 2000 users...............................................................................................212

Downloaded from ManualsPrinter.com Manuals 5

HP Deskjet F2200 All-in-One series

Downloaded from ManualsPrinter.com Manuals HP Deskjet F2200 All-in-One series Help 7

The HP All-in-One at a glance

Downloaded from ManualsPrinter.com Manuals HP All-in-One overview 9

5 Print cartridge door

8 Rear access door

9 Rear USB port

* Use only with the power adapter supplied by HP.

Control panel buttons

Label Icon Name and Description

3 Cancel: Stops a print, copy, or scan job.

6 Start Copy Black: Starts a black-and-white copy job.

7 Start Copy Color: Starts a color copy job.

Downloaded from ManualsPrinter.com Manuals Control panel buttons 11

Status light overview

2 Check Print Cartridge lights

4 Paper Type lights (for the Paper Type button)

Light status What it means

The Paper light is blinking. • The HP All-in-One is out of paper.

• The print cartridge is not intended for use in this HP All-in-One.

NOTE: HP All-in-One will still operate as a printer.

All lights are blinking. The HP All-in-One has a fatal error.

Use the HP Photosmart software

Downloaded from ManualsPrinter.com Manuals Use the HP Photosmart software 13

Downloaded from ManualsPrinter.com Manuals Find more information 15

Downloaded from ManualsPrinter.com Manuals How do I? 17

Supported connection types

Description Recommended number Supported software Setup instructions

Printer sharing Up to five. All features resident on Follow the instructions in

Use printer sharing

To enable printer sharing on a Windows computer

Downloaded from ManualsPrinter.com Manuals Connection information 19

To load an original on the glass

Load originals and load paper

3. Close the lid.

Choose papers for printing and copying

Downloaded from ManualsPrinter.com Manuals Load originals and load paper 21

This section contains the following topics:

Recommended papers for printing and copying

NOTE: To achieve a borderless print, you must use 10 x 15 cm (4 x 6 inch) paper

HP Premium Plus Photo Paper

HP Premium Photo Paper