Aspire 5730z 5330 PDF

Aspire 5730Z/5330 Series
Service Guide
Service guide files and updates are available

on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
Revision History
Please refer to the table below for the updates made on Aspire 5730Z/5330 Series service guide.
Date Chapter Updates
II
Copyright
Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in
any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without
the prior written permission of Acer Incorporated.
Disclaimer
The information in this guide is subject to change without notice.
Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the
contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular
purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is". Should the
programs prove defective following their purchase, the buyer (and not Acer Incorporated, its distributor, or its
dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential
damages resulting from any defect in the software.
Acer is a registered trademark of Acer Corporation.

Intel is a registered trademark of Intel Corporation.
Pentium and Pentium II/III are trademarks of Intel Corporation.
Other brand and product names are trademarks and/or registered trademarks of their respective holders.
III
Conventions
The following conventions are used in this manual:
SCREEN MESSAGES Denotes actual messages that appear

on screen.
NOTE Gives bits and pieces of additional
information related to the current
topic.
WARNING Alerts you to any damage that might
result from doing or not doing specific
actions.
CAUTION Gives precautionary measures to
avoid possible hardware or software
problems.
IMPORTANT Reminds you to do specific actions
relevant to the accomplishment of
procedures.
IV
Preface
Before using this information and the product it supports, please read the following general information.
1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION
decided for Acer's "global" product offering. To better fit local market requirements and enhance product
competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g.
add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered
in this generic service guide. In such cases, please contact your regional offices or the responsible
personnel/channel to provide you with further technical details.
2. Please note WHEN ORDERING FRU PARTS, that you should check the most up-to-date information
available on your regional web or channel. If, for whatever reason, a part number change is made, it will
not be noted in the printed Service Guide. For ACER-AUTHORIZED SERVICE PROVIDERS, your Acer
office may have a DIFFERENT part number code to those given in the FRU list of this printed Service
Guide. You MUST use the list provided by your regional Acer office to order FRU parts for repair and
service of customer machines.
V
VI
Table of Contents
System Specifications 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Easy-Launch Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Touchpad basics (with two-click buttons) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Using the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Lock Keys and embedded numeric keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Windows Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Hot Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Special Key (only for certain models) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Launching Acer Empowering Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Empowering Technology password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Acer eAudio Management (only for certain models) . . . . . . . . . . . . . . . . . . . . . 17
Acer ePower Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Acer eDataSecurity Management (only for certain models) . . . . . . . . . . . . . . . .19
Acer eRecovery Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Acer eSettings Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Windows Mobility Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Using the System Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Acer GridVista (dual-display compatible) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Hardware Specifications and Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
System Utilities 33
BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Boot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
BIOS Flash Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Remove HDD/BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Machine Disassembly and Replacement 47
Disassembly Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Pre-disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Disassembly Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
External Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
External Modules Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Removing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Removing the SD dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the ExpressCard dummy card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Removing the Lower Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Removing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Removing the WLAN Board Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Removing the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Main Unit Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
VII
Table of Contents
Removing the Middle Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Removing the Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
Removing the Heatsink Fan Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Removing the CPU Heatsink Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Removing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Separating the Upper Case from the Lower Case . . . . . . . . . . . . . . . . . . . . . . .70
Removing the LED Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Removing the Speaker Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Removing the Touchpad Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Removing the Modem Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Removing the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Removing the USB Board Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Removing the Bluetooth Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .86
LCD Module Disassembly Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
LCD Module Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Removing the LCD Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
Removing the LCD panel with the Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Removing the Inverter Board and FPC Cable . . . . . . . . . . . . . . . . . . . . . . . . . .90
Removing the LCD Brackets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .93
Removing the Antennas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Removing the Web Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
Troubleshooting 97
System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
External Diskette Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
External CD-ROM Drive Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Keyboard or Auxiliary Input Device Check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Memory Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Power System Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Touchpad Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Power-On Self-Test (POST) Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Index of Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Phoenix BIOS Beep Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Index of Symptom-to-FRU Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
Intermittent Problems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Undetermined Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Jumper and Connector Locations 117
Top and Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .117
Clearing Password Check and BIOS Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
Clearing Password Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .119
BIOS Recovery by Crisis Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
FRU (Field Replaceable Unit) List 121
Aspire 5730Z/5330 Series Exploded Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Model Definition and Configuration 130
Aspire 5730Z/5330 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .130
Test Compatible Components 155
Microsoft® Windows® Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .156
VIII
Table of Contents
Online Support Information 159
Index 161
IX
Table of Contents
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many feature:
Platform
Intel® Centrino® 2 processor technology, featuring:
K Intel® Core™2 Duo processor*
K Intel® Pentium® dual-core processor*
K Intel® Celeron® processor*
K Mobile Intel® GL40/GM45 Express Chipset*
K Intel® Wireless WiFi Link 5100/5300*
K Acer InviLink™ Nplify™ 802.11b/g/Draft-N*
K Acer InviLink™ 802.11b/g*
System Memory
K Dual-channel SDRAM support
K Up to 1 GB of DDR2 667 MHz memory, upgradeable to 2 GB using two soDIMM modules*
K Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules*
Display and graphics

K 15.4" WXGA 1280 x 800
K Mobile Intel® GL40/GM45 Express Chipset*
Storage subsystem
K 2.5" hard disk drives
K Optical drive options:
jDVD-Super Multi double-layer drive
K 5-in-1 card reader
Special keys and controls

K 88-/89-/93-key keyboard
K Touchpad pointing device
K Empowering Key
K Easy-launch buttons: WLAN, Volume Up, Volume Down and Bluetooth
Audio
K Two built-in stereo speakers
K High-definition audio support
K MS-Sound compatible
Chapter 1 1
K Built-in microphone
Communication
K Integrated Acer Crystal Eye webcam*
K WLAN:
jAcer InviLink™ Nplify™ 802.11b/g/Draft-N*
jAcer InviLink™ 802.11b/g*
K WPAN: Bluetooth® 2.0+Enhanced Data Rate (EDR)*
K LAN: Gigabit Ethernet; Wake-on-LAN ready
K Modem: 56K ITU V.92; Wake-on-Ring ready
I/O Ports
K ExpressCard™/54 slot
K 5-in-1 card reader (SD/MMC/MS/MS PRO/xD)
K 4 USB 2.0 ports
K External display (VGA) port
K Headphones/speaker/line-out jack*
K Microphone-in jack
K Line-in jack
K Ethernet (RJ-45) port
K Modem (RJ-11) port
K DC-in jack for AC adapter
Environment
K Temperature:
jOperating: 5 °C to 35 °C
jNon-operating: -20 °C to 65 °C
K Humidity (non-condensing):
jOperating: 20% to 80%
jNon-operating: 20% to 80%
NOTE: "*" "Only for certain models"
NOTE: The specifications listed above are for reference only. The exact configuration of your PC depends on
the model purchased.
2 Chapter 1
System Block Diagram
Chapter 1 3
Your Acer Notebook tour
After knowing your computer features, let us show you around your new computer.
Front View
1
3
14
4
5
9
6
13
7 12
8 11
9 10
Icon Item Description

1 Acer Crystal Eye Web camera for video communication.
2 Display screen Also called Liquid-Crystal Display (LCD), displays computer
output.
3 Power button Turns the computer on and off.
4 Speakers Left and right speakers deliver stereo audio output.

5/7 Easy-launch Buttons for launching frequently used programs.
buttons
6 VOL+/ Volume up/Volume Increases the sound volume/Decreases the sound volume.
VOL- down
8 Palmrest Comfortable support area for your hands when you use the
computer.
9 Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of
the computer's functions and components.
10 Click buttons The left and right buttons function like the left and right mouse
(left and right) buttons.
4 Chapter 1
11 Touchpad Touch-sensitive pointing device which functions like a computer
mouse.
12 Microphone Internal microphone for sound recording.
13 Keyboard For entering data into your computer.

14 Empowering key Launch Acer Empowering Technology
1 Acer PureZone Two internal stereo microphones for sound recording.
Closed Front View

1 Latch Locks and releases the lid.
Chapter 1 5
Left View
1 2 3 4 5 6 7 8
# Icon Item Description

1 Kensington lock slot Connects to a Kensington-compatible computer security
lock.
2 DC-in jack Connects to an AC adapter.
3 Ethernet (RJ-45) Connects to an Ethernet 10/100/1000-based network.

port
4 External display Connects to a display device

(VGA) port (e.g., external monitor, LCD projector).
5 USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB
camera) (only for certain models).
6 Line-in jack Accepts audio line-in devices (e.g., audio CD player,
stereo walkman).
Microphone-in jack Accepts input from external microphones.
Headphones/ Connects to audio line-out devices (e.g., speakers,

speaker/line-out headphones).
jack with
S/PDIF support
7 ExpressCard/54 Accepts one ExpressCard/54 module.
slot
8 5-in-1 card reader Accepts Secure Digital (SD), MultiMediaCard (MMC),
Memory Stick (MS), Memory Stick PRO (MS PRO), xD-
Picture Card (xD).
Right View
1 234 5 6

1 Optical drive Internal optical drive; accepts CDs or DVDs.
6 Chapter 1
2 Optical disk access Lights up when the optical drive is active.
indicator
3 Optical drive eject Ejects the optical disk from the drive.
button
4 Emergency eject hole Ejects the optical drive tray when the computer is
turned off.
Note: Insert a paper clip to the emergency eject
hole to eject the optical drive tray when the
computer is off.
5 USB 2.0 port Connect to USB 2.0 devices (e.g., USB mouse,
USB camera).
6 Modem (RJ-11) port Connects to a phone line.
Rear View
# Icon Item Description

1 Ventilation slots Enable the computer to stay cool, even after
prolonged use.
Chapter 1 7
Bottom View
1 6
2
3
5
4

1 Battery bay Houses the computer's battery pack.
2 Battery lock Locks the battery in position.
3 Battery release Releases the battery for removal.

latch
4 Memory Houses the computer's main memory.

compartment
5 Hard disk bay Houses the computer's hard disk (secured with
screws).
6 Ventilation slots Enable the computer to stay cool, even after

and cooling fan prolonged use.
Note: Do not cover or obstruct the opening of the
fan.
8 Chapter 1
Indicators
The computer has several easy-to-read status indicators. The front panel indicators are visible even when the
computer cover is closed.
Icon Function Description
HDD Indicates when the hard disk drive is
active.
Num Lock Lights up when Num Lock is

activated.
Caps Lock Lights up when Caps Lock is
activated.
Power Indicates the computer's power
status.
Battery Indicates the computer's battery
status.
NOTE: 1. Charging: The light shows amber when the battery is charging. 2. Fully charged: The light shows
green when in AC mode.
Easy-Launch Buttons
Located beside the keyboard are application buttons. These buttons are called easy-launch buttons. They are:
WLAN, Internet, email, Bluetooth, Arcade and Acer Empowering Technology.
The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To
set the Web browser, mail and programmable buttons, run the Acer Launch Manager.You can access the
Launch Manager by clicking on Start, All Programs, and then Launch Manager to start the application.
Icon Function Description

Wireless communication Enables/disables the wireless function. Indicates the status
button/indicator of wireless LAN communication.
(manufacturing option)
VOL+ Volume up Increases the sound volume.
VOL- Volume down Decreases the sound volume.
Bluetooth communication Enables/disables the Bluetooth function. Indicates the
button/indicator status of Bluetooth communication.
(manufacturing option)
Acer Empowering Launch Acer Empowering Technology (user-
Technology programmable)
Chapter 1 9
Touchpad basics (with two-click buttons)
The following items show you how to use the touchpad with two-click buttons.
1 2 3
K Move your finger across the touchpad (1) to move the cursor.
K Press the left (2) and right (3) buttons located beneath the touchpad to perform selection and execution
functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the
touchpad is the same as clicking the left button.
Function Left button (2) Right button (3) Main touchpad (1)
Execute Quickly click twice. Tap twice (at the same speed as double-clicking
a mouse button).
Select Click once. Tap once.
Drag Click and hold, then use Tap twice (at the same speed as double-clicking
finger on the touchpad a mouse button); rest your finger on the touchpad
to drag the cursor. on the second tap and drag the cursor.
Access Click once.
context menu
NOTE: Illustrations for reference only. The exact configuration of your PC depends on the model purchased.
NOTE: When using the touchpad, keep it — and your fingers — dry and clean. The touchpad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping harder will not increase
the touchpad's responsiveness.
NOTE: By default, vertical and horizontal scrolling is enabled on your touchpad. It can be disabled under
Mouse settings in Windows Control Panel.
10 Chapter 1
Using the Keyboard
The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function
and special keys.
Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off.
Lock key Description

Caps Lock When Caps Lock is on, all alphabetic characters typed are
in uppercase.
Num Lock When Num Lock is on, the embedded keypad is in numeric mode. The keys
<Fn> + <F11> function as a calculator (complete with the arithmetic operators +, -, *, and /).
Use this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
NOTE: <Fn> + <F11> works only for certain models.
Scroll Lock <Fn> + When Scroll Lock is on, the screen moves one line up or down when you press
<F12> the up or down arrow keys respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the key caps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access Num Lock on Num Lock off

Number keys on Type numbers in a normal manner.
embedded keypad
Cursor-control keys on Hold <Shift> while using cursor- Hold <Fn> while using cursor-
embedded keypad control keys. control keys.
Main keyboard keys Hold <Fn> while typing letters on Type the letters in a normal
embedded keypad. manner.
Chapter 1 11
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key Description
Windows Pressed alone, this key has the same effect as
key clicking on the Windows Start button; it launches the
Start menu.
It can also be used with other keys to provide a
variety of functions:
< >: Open or close the Start menu
< > + <D>: Display the desktop
< > + <E>: Open Windows Explore
< > + <F>: Search for a file or folder
< > + <G>: Cycle through Sidebar gadgets
< > + <L>: Lock your computer (if you are
connected to a network domain), or switch users (if
you're not connected to a network domain)
< > + <M>: Minimizes all windows
< > + <R>: Open the Run dialog box
< > + <T>: Cycle through programs on the
taskbar
< > + <U>: Open Ease of Access Center
< > + <X>: Open Windows Mobility Center
< > + <BREAK>: Display the System Properties
dialog box
< > + <SHIFT+M>: Restore minimized windows
to the desktop
< > + <TAB>: Cycle through programs on the
taskbar by using Windows Flip 3-D
< > + <SPACEBAR>: Bring all gadgets to the
front and select Windows Sidebar
<CTRL> + < > + <F>: Search for computers (if
you are on a network)
<CTRL> + < > + <TAB>: Use the arrow keys to
cycle through programs on the taskbar by using
Windows Flip 3-D
Note: Depending on your edition of Windows Vista,
some shortcuts may not function as described.
Application This key has the same effect as clicking the right
key mouse button; it opens the application's context
menu.
12 Chapter 1
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer’s controls like screen
brightness, volume output and the BIOS utility.
To activate hot keys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey Icon Function Description

<Fn> + <F1> Hotkey help Displays help on hotkeys.
<Fn> + <F2> Acer eSettings Launches Acer eSettings in Acer Empowering

Technology.
<Fn> + <F3> Acer ePower Launches Acer ePower Management in Acer
Management Empowering Technology.
<Fn> + <F4> Sleep Puts the computer in Sleep mode.
<Fn> + <F5> Display toggle Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6> Screen blank Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F7> Touchpad toggle Turns the internal touchpad on and off.
<Fn> + <F8> Speaker toggle Turns the speakers on and off.
<Fn> + < > Brightness up Increases the screen brightness.
<Fn> + < > Brightness down Decreases the screen brightness.
<Fn> + < > Volume up Increases the sound volume

(only for certain models).
<Fn> + < > Volume down Decreases the sound volume
(only for certain models).
Chapter 1 13
Special Key (only for certain models)
You can locate the Euro symbol and the US dollar sign at the upper-center
and/or bottom-right of your keyboard.
The Euro symbol

1. Open a text editor or word processor.
2. Either press < > at the bottom-right of the keyboard, or hold <Alt Gr> and then press the <5> key at the
upper-center of the keyboard.
NOTE: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/
typography/faq/faq12.htm for more information.
The US dollar sign

1. Open a text editor or word processor.
2. Either press < > at the bottom-right of the keyboard, or hold <Shift> and then press the <4> key at the
upper-center of the keyboard.
NOTE: This function varies according to the language settings.
14 Chapter 1
Acer Empowering Technology
The Empowering Technology toolbar makes it easy for you to access frequently used functions and manage
your new Acer system. Activated by pressing the Empowering Key, it provides access to the following utilities:
NOTE: The following content is for general reference only. Actual product specifications may vary.
K Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home
Theater on your system (only for certain models).
K Acer ePower Management optimizes battery usage via customizable power plans.
K Acer eDataSecurity Management protects data with passwords and encryption (only for certain
models).
K Acer eRecovery Management backs up and recovers data flexibly, reliably
and completely.
K Acer eSettings Management accesses system information and adjusts settings easily.
For more information, right-click on the Empowering Technology toolbar, then select Help. For help with a
particular utility, launch the utility and click the icon at the bottom of the active window.
Launching Acer Empowering Technology

To launch Acer Empowering Technology:
1. Press the Empowering Key to display the Acer Empowering Technology toolbar on the desktop.
2. To hide the toolbar, press the Empowering Key again or click the hide button on the toolbar.
You may also launch Acer Empowering Technology by running the program from the Acer Empowering
Technology program group in the Start menu, or by double-clicking the icon if you have created a
desktop shortcut.
To launch Acer Empowering Technology applications:

1. On the Acer Empowering Technology toolbar, click the icon that corresponds to the application you want
to launch.
2. When you mouse over an application icon, a quick menu appears below the toolbar. The quick menu
allows you to perform certain tasks simply and quickly.
3. You may also run the application by selecting it from the Acer Empowering Technology program group in
the Start menu.
NOTE: You may also double-click or right-click to run Acer eAudio Management, and right-click to
run Acer ePower Management from the system tray.
Chapter 1 15
Empowering Technology password
You must set the Empowering Technology password to use the password protection feature of Acer
eRecovery Management to protect your data.
To set the Empowering Technology password:

1. Launch Acer eRecovery Management.
2. Click the Restore tab.
3. Click Password settings. The Empowering Technology Password Center dialogue box pops up.
4. Click Create a new password.
5. In the Create a New Password dialogue box, key in and confirm your password in the appropriate boxes.
Your password should have a minimum of 4 and a maximum of 12 characters.
6. Enter a password hint that will help you remember your password.
7. Make sure the box Use for Acer eRecovery Management is checked.
8. Click OK to set the password.
16 Chapter 1
Acer eAudio Management (only for certain models)
Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby Home Theater on
your system. Select Movie or Game mode to experience the awesome realism of 5.1-channel audio output
from the speakers fitted to your system via Dolby Surround sound technology. Music mode lets you enjoy your
favorite tunes, in vivid detail.
To choose your playback device, click the icon on the upper right side of the Acer eAudio Management
window.
Chapter 1 17
Acer ePower Management
Acer ePower Management features a straightforward user interface for configuring your power management
options. To access this utility, select Acer ePower Management from the Empowering Technology toolbar, run
the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows
power icon in the system tray and select Acer ePower Management.
Using power plans

Acer ePower Management comes with three predefined power plans: Balanced, High performance and
Power saver.
View and adjust settings for On Battery and Plugged In modes by clicking the appropriate tabs. For more
power options, click in the Acer ePower Management utility, or right-click the Windows power icon in the
system tray and select Power Options.
You can also create customized power plans. You can create, switch between, edit, delete and restore power
plans, as described below.
To create a new power plan:

Creating customized power plans allows you to save and quickly switch to a personalized set of power
options.
1. Click the New power plan option or icon .
2. Enter a name for your new power plan.
3. Choose a predefined power plan to base your customized plan on.
4. If necessary, change the display, sleep and hibernation settings you want your computer to use.
5. Click OK to save your new power plan.
To switch between power plans:

1. Move your mouse over the Acer ePower Management application on the Acer Empowering
Technology toolbar. The quick menu appears.
Select the power plan you want to switch to.
2. You may also switch between power plans by launching the Acer ePower Management application.
Select the power plan you wish to switch to, then click Apply.
To edit a power plan:

Editing a power plan allows you to adjust system settings like LCD brightness, CPU speed and Graphics
power mode (only for certain models).
1. Switch to the power plan you wish to edit.
2. Adjust settings as required.
3. Click Apply or Save to save your new settings.
NOTE: You can revert to the default settings of the predefined power plans by clicking the Restore button.
To delete a power plan:
You cannot delete the power plan you are currently using. The active power plan will mark with in upper
left corner of power plan icon. If you want to delete the active power plan, switch to another one first.
1. Select the power plan you wish to delete.
2. Click the Delete this plan icon.
NOTE: You cannot delete the predefined power plans, but you can modify the settings of the predefined power
plans.
18 Chapter 1
Battery status
1. The quick menu shows the remaining battery life based on current usage.
2. You can also launch the Acer ePower Management application and refer to the Battery status panel
located just below the power plans.
3. Click the Battery tab to view remaining battery life, battery status, and remaining battery life in standby
and hibernate modes.
Acer eDataSecurity Management (only for certain models)

Acer eDataSecurity Management is an encryption utility that protects your files from being accessed by
unauthorized persons. It is conveniently integrated with Windows Explorer as a shell extension for quick data
encryption/decryption and also supports on-the-fly file encryption for Lotus Notes and Microsoft Outlook.
On first use, the Acer eDataSecurity Management setup wizard will prompt you to create the Master
Password. You will use this password to access the Personal Secure Disk (PSD). The Master Password may
also be used to encrypt/decrypt files by default.
Chapter 1 19
If you set a different password to encrypt a file, but you forgot the encryption password, you can use the
Master Password to decrypt the file.
NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose
the password, the Master Password is the only other key capable of decrypting the file. If you lose both
passwords, there will be no way to decrypt your encrypted file! Be sure to safeguard all related
passwords!
Acer eRecovery Management

Acer eRecovery Management is a versatile backup utility. It allows you to create full or incremental backups,
burn the factory default image to optical disc, and restore from previously created backups or reinstall
applications and drivers. By default, user-created backups are stored to the D:\ drive.
Acer eRecovery Management provides you with:
K Backup:
20 Chapter 1
jBack up factory default to CD/DVD
jBack up drivers and applications to CD/DVD
jCreate user backup
jManage user backups
K Restore:
jRestore system to factory default
jReinstall applications/drivers
jRestore system from user backup
jPassword settings
To use the password protection feature of Acer eRecovery Management to protect your data, you must first set
the Empowering Technology password. To set the password, refer to the section "Empowering Technology
password".
For more information, please refer to"Acer eRecovery Management" on page 62 in the Acer System
User's Guide.
NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery
Management's Backup factory default to CD/DVD feature to burn a backup image to CD or DVD. To
ensure the best results when recovering your system using a CD or Acer eRecovery Management,
detach all peripherals (except the external Acer ODD, if your computer has one), including your Acer
ezDock.
Chapter 1 21
Acer eSettings Management
Acer eSettings Management allows you to inspect hardware specifications, set BIOS passwords and modify
boot options.
Acer eSettings Management also:
K Provides a simple graphical user interface for navigation.
K Prints and saves hardware specifications.
K Lets you set an asset tag for your system.
22 Chapter 1
Windows Mobility Center
The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can
quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings
include display brightness, volume, power plan, wireless networking on/off, external display settings,
synchronization status and presentation settings.
Windows Mobility Center also includes Acer-specific settings like sharing folders overview/sharing service on
or off, Bluetooth Add Device (if applicable), and a shortcut to the Acer user guide, drivers and utilities.
To launch Windows Mobility Center:
K Use the shortcut key < > + <X>.
K Start Windows Mobility Center from the Control panel.

K Start Windows Mobility Center from the Accessories program group in the Start menu.
K Launch Windows Mobility Center by right-clicking in the system tray and select Windows Mobility
Center.
Chapter 1 23
Using the System Utilities Start Control Panel Display
Settings (2)
Extend my windows desktop onto this monitor
Acer GridVista (dual-display compatible)
Apply OK
NOTE: This feature is only available on certain models.
To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then
select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the
display box and then click the check box Extend my windows desktop onto this monitor. Finally, click
Apply to confirm the new settings and click OK to complete the process.
Acer GridVista is a handy utility that offers four pre-defined display settings so you can view multiple windows
on the same screen. To access
Start this function, please go to Start>All
All Programs Programs and click on Acer GridVista.
Acer GridVista
You may choose any one of the four display settings indicated below:
Double (vertical), Triple (primary at left), Triple (primary at right), or Quad Acer Gridvista is dual-display
compatible, allowing two displays to be partitioned independently.
Acer Gridvista is dual-display compatible, allowing two displays to be partitioned independently.
AcerGridVista is simple to set up:

1. Run Acer GridVista and select your preferred screen configuration for each display from the task bar.
2. Drag and drop each window into the appropriate grid.
3. Enjoy the convenience of a well-organized desktop.
24 Chapter 1
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's
recommended value.
Chapter 1 25
Hardware Specifications and Configurations
Processor
Item Specification
CPU type Intel® Core™2 Duo Mobile Processor P8400 (2.26G), P8600 (2.4
G), P9500 (2.53G), T9400 (2.53G), T9600 (2.8G)
Core logic Mobile Intel® 945 Express Chipset
CPU package Socket B (P8400, P8600, P9500) and Socket P (T9400, T9600)
CPU core voltage 1.0375V to 1.3V
CPU Fan True Value Table
DTS(degree C) Fan Speed (rpm) Acoustic Level (dBA)

45-50 0-3000 29
55-66 0-3300 33
68-74 3300-3800 38
78-83 3800-4100 40
86-91 4100-4800 40
Throttling 50%: On= 99 ° C; OFF=93 ° C
OS shut down at 105 ° C; H/W shot down at 110 ° .C

BIOS
Item Specification
BIOS vendor Phoenix
BIOS Version 1.04c
System Memory
Item Specification
Memory controller Built-in
Memory size 0MB (no on-board memory)
DIMM socket number 2 sockets
Supports memory size per socket 2048MB
Supports maximum memory size 4G for 64bit OS (with two 2GB SODIMM)
Supports DIMM type DDR 2 Synchronous DRAM
Supports DIMM Speed 667 MHz
Supports DIMM voltage 1.8V and 0.9V
Supports DIMM package 200-pin soDIMM
Memory module combinations You can install memory modules in any combinations as long as
they match the above specifications.
26 Chapter 1
Memory Combinations
Slot 1 Slot 2 Total Memory

0MB 256MB 256MB
0MB 512MB 512MB
0MB 1024MB 1024MB
0MB 2048MB 2048MB
256MB 256MB 512MB
256MB 512MB 768MB
256MB 1024MB 1280MB
256MB 2048MB 2304MB
512MB 256MB 768MB
512MB 512MB 1024MB
512MB 1024MB 1536MB
512MB 2048MB 2560MB
1024MB 0MB 1024MB
1024MB 256MB 1280MB
1024MB 512MB 1536MB
1024MB 1024MB 2048MB
1024MB 2048MB 3072MB
2048MB 0MB 2048MB
2048MB 256MB 2304MB
2048MB 512MB 2560MB
2048MB 1024MB 3072MB
2048MB 2048MB 4096MB
NOTE: Above table lists some system memory configurations. You may combine DIMMs with various
capacities to form other combinations. On above table, the configuration of slot 1 and slot 2 could be
reversed.
Item Specification
LAN Chipset Broadcom BCM5764/Broadcom BCM5765
Supports LAN protocol 10/100/1000 Mbps
LAN connector type RJ45
LAN connector location Left side
Features Integrated 10/100 BASE-T transceiver
Wake on LAN support compliant with ACPI 2.0
PCI v2.2
Bluetooth Interface
Item Specification
Chipset Foxconn Bluetooth FOX_BRM_2.0 F/W 300
Data throughput 723 bps (full speed data rate)
Protocol Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG
specification is ratified).
Interface USB 1.1
Chapter 1 27
Bluetooth Interface
Item Specification
Connector type USB
Wireless Module 802.11b/g
Item Specification
Chipset WLAN 802.11ABGN SHIRLEYPEAK1*2
Data throughput 11~54 Mbps, up to 270 Mbps for Draft-N
Protocol 802.11b+g, Draft-N
Interface PCI bus (mini PCI socket for wireless module)
Hard Disk Drive Interface
Item
Vendor & HGST WD1600BEVT- SEAGATE SATA WD WD3200BEVT-
Model Name HTS542512K9SA00 22ZCT0 ST9250827AS 22ZCT0 ML125
BRONCO-B LF HITACHI TOSHIBA
SEAGATE HTS541616J9SA00 MK2546GSX LF
ST9120817AS LF LF HGST
TOSHIBA SEAGATE SATA HTS542525K9SA00
MK1246GSX LF ST9160827AS LF
WD1200BEVS- TOSHIBA WD WD2500BEVS-
22UST0 ML125 LF MK1646GSX LF 22UST0 ML125
Capacity 120000 160000 250000 320000
(MB)
Bytes per 512 512 512 N/A
sector
Data heads 3 3/4 4 N/A
Drive Format
Disks 2 2 2 N/A
Spindle 5400 RPM 5400 RPM 5400 RPM 5400 RPM
speed
(RPM)
Performance Specifications
Buffer size 8MB 8MB 8MB 8MB
Interface SATA SATA SATA SATA
Max. media 540 540 540 850
transfer rate
(disk-buffer,
Mbytes/s)
DC Power Requirements
Voltage 5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5%
tolerance
28 Chapter 1
Optical Disc Drive
Item Specification
Vendor & model name TOSHIBA SUPER-MULTI DRIVE DL 8X TS-L633A LF
PIONEER SUPER-MULTI DRIVE 8X DVR-TD08RS LF
PANASONIC SUPER-MULTI DRIVE DL 8X UJ-870A LF
HLDS SUPER-MULTI DRIVE TRAY DL 8X GSA-T50N LF
HLDS SUPER-MULTI DRIVE DL 8X GSA-T50N LF
SONY SUPER-MULTI DRIVE DL 8X AD-7560S LF
PLDS SUPER-MULTI DRIVE DL 8X DS-8A2S LF
Performance Specification With CD Diskette With DVD Diskette
Transfer rate (KB/sec) Sustained: Sustained:
Max 3.6Mbytes/sec Max 10.08Mbytes/sec
Buffer Memory 2MB
Interface SATA
Applicable disc format Applicable disc format
CD: CD-DA, CD-ROM, CD-ROM XA, Photo CD (multi-session), Video
CD, Cd-Extra (CD+), CD-text
DVD: DVD-VIDEO, DVD-ROM, DVD-R (3.9GB, 4.7GB) DVD-R DL,
DVD-RW, DVD-RAM, DVD+R, DVD+R DL, DVD+RW
CD:
CD-DA (Red Book) - Standard Audio CD & CD-TEXT
CD-ROM (Yellow Book Mode1 & 2) - Standard Data
CD-ROM XA (Mode2 Form1 & 2) - Photo CD, Multi-Session
CD-I (Green Book, Mode2 Form1 & 2, Ready, Bridge)
CD-Extra/ CD-Plus (Blue Book) - Audio & Text/Video
Video-CD (White Book) - MPEG1 Video
CD-R (Orange Book Part)
CD-RW & HSRW (Orange Book Part Volume1 & Volume 2
Super Audio CD (SACD) Hybrid type
US & US+ RW
DVD:
DVD-ROM (Book 1.02), DVD-Dual
DVD-Video (Book 1.1)
DVD-R (Book 1.0, 3.9G)
DVD-R (Book 2.0, 4.7G) - General & Authoring
DVD+R (Version 1.0)
DVD+RW
DVD-RW (Non CPRM & CPRM)
DVD°”R Dual
Loading mechanism Load: Manual
Release: (a) Electrical Release (Release Button)
(b) Release by ATAPI command
(c) Emergency Release
Power Requirement
Input Voltage 5 V +/- 5% (Operating)
Chapter 1 29
Audio Interface
Item Specification
Audio Controller Realtek ALC883 Azalia and Amplifier Maxim MAX9710 &
MAX4411
Audio onboard or optional Built-in
Mono or Stereo Stereo
Resolution 18 bit stereo full duplex
Compatibility HD audio Interface; S/PDIF output for PCM or AC-3
content
Sampling rate 1Hz resolution VSR (Variable Sampling Rate)
Internal microphone Yes
Internal speaker / Quantity Yes/2 (1.5W speakers)
Video Memory
Item Specification
Chipset VGA CARD NB9P-GS/Intel GMA970 VGA
Memory size 512M GDDR3/
Item Specification
Chipset ICH8M
USB Compliancy Level 2.0
OHCI USB 1.1 and USB 2.0 Host controller
Number of USB port 3
Location Two on the right side/one on the front
Serial port function control Enable/Disable by BIOS Setup
System Board Major Chips
Item Controller
Core logic Mobile Intel® GM945/PM945 + ICH8M Express Chipset
VGA nVidia GeForce 9300 GS/9600M GT/UMA
USB 2.0 Intel ICH8M
Super I/O controller N/A
MODEM ALC 883
Bluetooth FOXCONN BCM2045 V2
Wireless 802.11 b+g WLAN 802.11ABGN SHIRLEYPEAK1*2
PCMCIA/ 5 in 1 Card Reader JMicron Cardreader JMB385
Audio Codec Audio Azalia(ALC888S)
Keyboard
Item Specification
Keyboard controller NS PC97541V
30 Chapter 1
Keyboard
Item Specification
Total number of keypads 84-/85-key
Windows logo key Yes
Internal & external keyboard work Plug USB keyboard to the USB port directly: Yes
simultaneously
Battery
Item Specification
Vendor Panasonic/Sanyo/Sony/Simplo
Battery Type Li-ion
Pack capacity 6Cell 4400 MAH/8Cell 4800 MAH
Number of battery cell 6/8
Package configuration 3 cells in series, 2 series in parallel
4 cells in series, 2 series in parallel
LCD 15.4” inch
Item Specification
Vendor & model name CMO/AUO/LG
Screen Diagonal (mm) 15.4 inches
Display resolution (pixels) 1280 x 800 WXGA
Pixel Pitch 0.204 x 0.204
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode Normally White
Typical White Luminance (NIT) 220
also called Brightness
Luminance Uniformity 1.25 max.
Contrast Ratio 400 typical
Response Time msec 8
Nominal Input Voltage VDD +3.3V
Viewing Angle (degree)
Horizontal: Right/Left 45/45
Vertical: Upper/Lower 15/35
Temperature Range( ° C)
Operating 0 to +50
Storage (shipping) -40 to +60
AC Adaptor
Item Specification
Input 100-240V~ 1.5A, 50-60Hz/
Output 19V 4.74A 90W/19V 3.42A 65W
Chapter 1 31
System Power Management
ACPI mode Power Management

Mech. Off (G3) All devices in the system are turned off completely.
Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned
off completely.
Working (G0/S0) Individual devices such as the CPU and hard disc may be
power managed in this state.
Suspend to RAM (S3) CPU set power down
VGA Suspend
PCMCIA Suspend
Audio Power Down
Hard Disk Power Down
CD-ROM Power Down
Super I/O Low Power mode
Save to Disk (S4) Also called Hibernation Mode. System saves all system
states and data onto the disc prior to power off the whole
system.
32 Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility
The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when “Press <F2> to enter Setup” message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Phoenix SecureCore(tm) Setup Utility

Information Main Security Boot Exit
C P U Ty p e : Intel (R) Core (TM)2 Duo CPU T9400 @ 2.53 GHz

CPU Speed: 2.53 GHz
IDE0 Model Name: XXXXXXXXXXX-(XX)
IDE0 Serial Number: XXXXXXXX
ATA P I M o d e l N a m e : XXXXXXXXXXX-XXX XX-XXXX-(XX)
S y s t e m B I O S Ve r s i o n : VX.XX
V G A B I O S Ve r s i o n : XX-XXX XXXXXX.XXX.XXX.XXX.XXXXXX
K B C Ve r s i o n : XX.XX
Serial Number: XXXXXXXXXXXXXXXXXXXXXXX
A s s e t Ta g N u m b e r : None
Product Name: Aspire 5730
Manufacturer Name: Acer
UUID: XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX
F1 Help Select Item -/+ C h a n g e Va l u e s F9 Setup Defaults

Esc Exit Select Menu Enter Select Sub-Menu F10 Save and Exit
Chapter 2 33
Navigating the BIOS Utility
There are five menu options: Information, Main, Security, Boot, and Exit.
Follow these instructions:
K To choose a menu, use the left and right arrow keys.
K To choose an item, use the up and down arrow keys.
K To change the value of a parameter, press F5 or F6.
K A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
K Press Esc while you are in any of the menu options to go to the Exit menu.
K In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
34 Chapter 2
Information
The Information screen displays a summary of your computer hardware information.

C P U Ty p e : Intel (R) Core (TM)2 Duo CPU T9400 @ 2.53 GHz

CPU Speed: 2.53 GHz
IDE0 Model Name: XXXXXXXXXXX-(XX)
IDE0 Serial Number: XXXXXXXX
ATA P I M o d e l N a m e : XXXXXXXXXXX-XXX XX-XXXX-(XX)
S y s t e m B I O S Ve r s i o n : VX.XX
V G A B I O S Ve r s i o n : XX-XXX XXXXXX.XXX.XXX.XXX.XXXXXX
K B C Ve r s i o n : XX.XX
Serial Number: XXXXXXXXXXXXXXXXXXXXXXX
A s s e t Ta g N u m b e r : None
Product Name: Aspire 5730
Manufacturer Name: Acer
UUID: XXXxXxXX-xXxX-XXxx-xXXx-xXXxXXxXxxXX

NOTE: The system information is subject to different models.
Parameter Description
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
IDE0 Model Name This field shows the model name of HDD installed on primary IDE master.
IDE0 Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name This field shows the model name of the Optical device installed in the system.
System BIOS Version Displays system BIOS version.
VGA BIOS Version This field displays the VGA firmware version of the system.
KBC Ver This field shows the keyboard
Serial Number This field displays the serial number of this unit.
Asset Tag Number This field displays the asset tag number of the system.
Product Name This field shows product name of the system.
Manufacturer Name This field displays the manufacturer of this system.
UUID Number Universally Unique Identifier (UUID) is an identifier standard used in software construction,
standardized by the Open Software Foundation (OSF) as part of the Distributed
Computing Environment (DCE).
Chapter 2 35
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.

Item Specific Help

S y s t e m Ti m e : [10:10:10]
System Date: [07/26/2008]
< Ta b > , < S h i f t - Ta b > , o r
System Memory: 640 KB <Enter> selects field.
Extended Memory: 4061 MB
Vi d e o M e m o r y : 32 MB
Quiet Boot: [Enabled]

Network Boot: [Enabled]
F12 Boot Menu: [Disabled]
D2D Recovery: [Enabled]
S ATA M o d e [AHCI]

NOTE: The screen above is for your reference only. Actual values may differ.
36 Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter Description Format/Option

System Time Sets the system time. The hours are displayed Format: HH:MM:SS
with 24-hour format. (hour:minute:second) System Time
System Date Sets the system date. Format MM/DD/YYYY (month/day/
year)
System Date
System Memory This field reports the memory size of the system.
Memory size is fixed to 640MB
Extended Memory This field reports the memory size of the
extended memory in the system.
Extended Memory size=Total memory size-1MB
VGA Memory Shows the VGA memory size.
Quiet Boot Determines if Customer Logo will be displayed or Option: Enabled or Disabled
not; shows Summary Screen is disabled or
enabled.
Enabled: Customer Logo is displayed, and
Summary Screen is disabled.
Disabled: Customer Logo is not displayed, and
Summary Screen is enabled.
Network Boot Enables, disables the system boot from LAN Option: Enabled or Disabled
(remote server).
F12 Boot Menu Enables, disables Boot Menu during POST. Option: Disabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The Option: Enabled or Disabled
function allows the user to create a hidden
partition on hard disc drive to store operation
system and restore the system to factory
defaults.
SATA Mode Control the mode in which the SATA controller Option: AHCI or IDE
should operate.
NOTE: The sub-items under each device will not be shown if the device control is set to disable or auto. This is
because the user is not allowed to control the settings in these cases.
Chapter 2 37
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.

Item Specific Help

Supervisor Password is: Clear
User Password is: Clear
HDD Password is: Clear Supervisor Password
controls access of the
Set Supervisor Password [Enter] w h o l e s e t u p u t i l i t y.
Set User Password [Enter] It can be used to boot
Set HDD Password [Enter] up when Password on
boot is enabled.
Password on Boot: [Disabled]

Esc Exit Select Menu Enter Select Su b - M e n u F10 Save and Exit
NOTE: Please refer to “Remove HDD/BIOS Password” section if you need to know how to remove HDD/BIOS
Password.
38 Chapter 2
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter Description Option

Supervisor Password Is Shows the setting of the Supervisor password Clear or Set
User Password Is Shows the setting of the user password. Clear or Set
HDD Password Is Shows the setting of the hard disk password. Clear or Set
Set Supervisor Password Press Enter to set the supervisor password.
When set, this password protects the BIOS
Setup Utility from unauthorized access. The
user can not either enter the Setup menu nor
change the value of parameters.
Set User Password Press Enter to set the user password. When
user password is set, this password protects
the BIOS Setup Utility from unauthorized
access. The user can enter Setup menu only
and does not have right to change the value of
parameters.
Set HDD Password Enter HDD Password.
Password on Boot Defines whether a password is required or not Disabled or Enabled
while the events defined in this group
happened. The following sub-options are all
requires the Supervisor password for changes
and should be grayed out if the user password
was used to enter setup.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
your password. If you forget your password, you may have to return your notebook computer to your
dealer to reset it.
Setting a Password
Follow these steps as you set the user or the supervisor password:
1. Use the “w” and “y” keys to highlight the Set Supervisor Password parameter and press the e key. The
Set Supervisor Password box appears:
2. Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3. Press e.
After setting the password, the computer sets the User Password parameter to “Set”.
4. If desired, you can opt to enable the Password on boot parameter.
5. When you are done, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2 39
Removing a Password
Follow these steps:
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set
Password box appears:
2. Type the current password in the Enter Current Password field and press e.
3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The
computer then sets the Supervisor Password parameter to “Clear”.
4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Changing a Password
1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set
Password box appears:
2. Type the current password in the Enter Current Password field and press e.
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4. Press e. After setting the password, the computer sets the User Password parameter to “Set”.
5. If desired, you can enable the Password on boot parameter.
6. When you are done, press u to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
The password setting is complete after the user presses u.
40 Chapter 2
If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
If the new password and confirm new password strings do not match, the screen will display the following
message.
Chapter 2 41
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the diskette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay.

Item Specific Help

Boot priority order:
1: IDE HDD: XXXXXXXXXXX-(XX) U s e < > o r < > to
2: IDE CD: XXXXXXXXXXX-XXX XX-XXXX-XX select a device, then
3: PCI LAN: Network Boot press <F6> to move it
4: USB HDD: up the list, or <F5>
5: USB FDD: to move it down the
6: USB Key: list. Press <Esc> to
7: USB CDROM: escape the menu.

42 Chapter 2
Exit
The Exit screen contains parameters that confirmed or discard the changes made to the parameters in the
BIOS Setup Utility.

Item Specific Help

Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults Exit System Setup and
Discard Changes save your changes to
Save Changes CMOS.

The table below describes the parameters in this screen.
Parameter Description
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Changes Exit utility without saving setup data to CMOS.
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
Chapter 2 43
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
K New versions of system programs
K New features or options
K Restore a BIOS when it becomes corrupted.
Use the Flash utility to update the system BIOS flash ROM.
NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery
Diskette before you use the Flash utility.
NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Flash.
NOTE: Please use the AC adaptor power supply when you run the Flash utility. If the battery pack does not
contain enough power to finish BIOS flash, you may not boot the system because the BIOS is not
completely loaded.
Fellow the steps below to run the Flash.
1. Prepare a bootable diskette.
2. Copy the flash utilities to the bootable diskette.
3. Then boot the system from the bootable diskette. The flash utility has auto-execution function.
44 Chapter 2
Remove HDD/BIOS Utility
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
K If you key in wrong HDD password for three time, “HDD password error code” would display on the
screen. See the image below.
K If you need to solve HDD password locked problem, you can run HDD_PW.EXE
1. Key in “hdd_pw 15494 0”
2. Select “2”
3. Choose one upper-case string
K Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.
Chapter 2 45
46 Chapter 2
Chapter 3
Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
K Wrist grounding strap and conductive mat for preventing electrostatic discharge
K Flat screwdriver
K Philips screwdriver
K Hex screwdriver
K Plastic flat screwdriver
K Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3 47
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.

4. Remove the battery pack.
Disassembly Process
The disassembly process is divided into the following stages:
• External module disassembly
• Main unit disassembly
• LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
Item Screw Color Part No.

A M2 x L8 Black 86.00E34.738
B M2.5 x L6 Black 86.00E12.536
C M2 x L3 Silver 86.9A522.3R0
D M3 x L4 Silver 86.9A524.4R0
E M2.5 x L10 Silver 86.00F84.73A
F M2 x L4 Silver 86.00C07.220
G M2 x L4 Black 86.00A02.140
H M2 x L3 Black 86.9A552.3R0
48 Chapter 3
External Module Disassembly Process
External Modules Disassembly Flowchart
The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you
on the components that need to be removed during servicing. For example, if you want to remove the main
board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
EXTERNAL MODULE DISASSEMBLY
TURN OFF POWER

AND PERIPHERALS
UNPLUG POWER
CABLES
REMOVE BATTERY
PACK
ExpressCard
SD DUMMY CARD
DUMMY CARD
Captive Screwx4 Ax6

LOWER
COVER
Hx1
Cx1
WLAN DIMM ODD HDD
BOARD MODULES MODULE MODULE
Cx2 Dx2
OPTICAL DISK OPTICAL HARD DISK HARD DISK
DRIVE LOCKER BRACKET DRIVE
BRACKET
Screw List

A M2 x L8 Black 86.00E34.738
D M3 x L4 Silver 86.9A524.4R0
H M2 x L3 Black 86.9A552.3R0
Chapter 3 49
Removing the Battery Pack
1. Turn base unit over.
2. Slide the battery lock/unlock latch to the unlock position.
3. Slide the battery release latch to the release position to pop out the battery pack, then remove the battery
pack from the main unit.
50 Chapter 3
Removing the SD dummy card
1. Push the SD dummy card all the way in to eject it.
2. Pull it out from the slot.
Removing the ExpressCard dummy card

1. Push the ExpressCard dummy card all the way in to eject it.
Chapter 3 51
2. Pull it out from the slot.
Removing the Lower Cover

1. See “Removing the Battery Pack” on page 50.
2. Remove the four captive screws and the six screws (A) on the lower cover.
Step Size (Quantity) Color Torque

1~6 M2.5 x L8 (6) Black 3.0 kgf-cm
52 Chapter 3
3. Use a plastic screw driver to carefully pry open the lower cover.
4. Remove the lower cover from the lower case.
Removing the DIMM

2. See “Removing the Lower Cover” on page 52..
3. Push out the latches on both sides of the DIMM socket to release the DIMM.
Chapter 3 53
4. Remove the DIMM module.
Removing the WLAN Board Modules

2. See “Removing the Lower Cover” on page 52.
3. Remove the white antenna cable that is taped to the WLAN board module.
54 Chapter 3
4. Disconnect the antenna cables from the WLAN board.
NOTE: There are 2 antenna cables connected to the WLAN board module. The Black antenna cable is
connected to the MAIN connector and the Gray antenna cable is connected to the AUX connector.
5. Move the antenna away from the WLAN board and remove the one screw (H) on the WLAN board to
release the WLAN board.

1 M2 x L3 (1) Black 1.6 kgf-cm
Chapter 3 55
6. Detach the WLAN board from the WLAN socket.
NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly.
Removing the Hard Disk Drive Module

3. Remove the one screw (C) securing the hard disk drive module.

1 M2 x L3 (1) Silver 1.6 kgf-cm
56 Chapter 3
4. Slide the hard disk drive module away from the connector.
5. Lift the hard disk drive module and remove it from the hard disk drive bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
6. Remove the two adhesive tape covering the two screws.
Chapter 3 57
7. Remove the two screws (D) securing the hard disk to the bracket and remove the hard disk from the
bracket.

1~2 M3 x L4 (2) Silver 3.0 kgf-cm
Removing the Optical Drive Module

58 Chapter 3
3. Use a pin and push it inside the emergency eject hole to eject the odd drive tray.
4. Carefully pull out the odd drive tray until the part of the module is visible and then slowly push back to
close the tray into the module with the module still partially exposed.
5. Slowly pull out the odd module from the odd drive bay.
Chapter 3 59
6. Remove the two screws (C) securing the locker bracket and remove the locker bracket from the optical
disk drive module.

60 Chapter 3
Main Unit Disassembly Process
Main Unit Disassembly Flowchart
MAIN UNIT DISASSEMBLY
MAIN UNIT
MIDDLE COVER Cx1
HEAT SINK FAN
KEYBOARD SCREW X 4
CPU
Ax2, Ex2 THERMAL MODULE
LCD MODULE
CPU
A x 11, G x 4
UPPER CASE
Cx1 Cx1 Cx4

Cx2
MODEM LED SPEAKER
CARD BOARD MODULE TOUCHPAD
BRACKET
Cx1 Cx1 TOUCHPAD

MODULE
MAIN BLUETOOTH USB
BOARD MODULE MODULE
Screw List

A M2 x L8 Black 86.00E34.738
E M2.5 x L10 Silver 86.00F84.73A
G M2 x L4 Black 86.00A02.140
H M2 x L3 Black 86.9A552.3R0
Chapter 3 61
Removing the Middle Cover
2. Use a plastic screw driver to pry loose the side of the middle cover.
3. Carefully pry loose the middle cover from the latches securing it and remove the middle cover.
62 Chapter 3
Removing the Keyboard
2. See “Removing the Middle Cover” on page 62.
3. Push down on the lock and release the latches securing the keyboard to the upper case.
4. Carefully pry loose the keyboard and turn it over on the touchpad area.
Chapter 3 63
5. Disconnect the keyboard cable from the main board to remove the keyboard.
Removing the Heatsink Fan Module

3. Disconnect the heatsink fan connector from the main board.
64 Chapter 3
4. Remove the one screw (C) securing the heatsink fan module in place.

5. Carefully lift up the heatsink fan module.
Removing the CPU Heatsink Module

3. See “Removing the Heatsink Fan Module” on page 64.
Chapter 3 65
4. Remove the four screws securing the CPU heatsink module.
5. Carefully remove the heatsink module from the system.
Removing the CPU

4. See “Removing the CPU Heatsink Module” on page 65.
5. Using a flat screwdriver, turn the CPU socket latch counter-clockwise to release the CPU.
66 Chapter 3
6. Lift up carefully to remove the CPU.
NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown.
Removing the LCD Module

2. See “Removing the SD dummy card” on page 51.
3. See “Removing the ExpressCard dummy card” on page 51.
5. See “Removing the WLAN Board Modules” on page 54.
Chapter 3 67
9. Turn over the system and remove the two screws (A) from the bottom of the left and right hinges.

1~2 M2.5 x L8 (2) Black 3.0 kgf-cm
10. Disconnect the LCD cable connector from the main board.
68 Chapter 3
11. Carefully pull out the wireless antenna cables from the hole and release the cables from the latches.
12. Remove the two screws (E) from the left and right hinge of the LCD module.

1~2 M2.5 x L10 (2) Silver 3.0 kgf-cm
Chapter 3 69
13. Carefully remove the LCD module from the base unit.
NOTE: When connecting the cable back to the unit, please note that the cable should be routed well.
Separating the Upper Case from the Lower Case

5. See “Removing the DIMM” on page 53.
7. See “Removing the Hard Disk Drive Module” on page 56.
8. See “Removing the Optical Drive Module” on page 58.
10. See “Removing the Keyboard” on page 63.
13. See “Removing the CPU” on page 66.
14. See “Removing the LCD Module” on page 67.
70 Chapter 3
15. Disconnect the touchpad cable from the TPAD1 connector on the main board.
16. Disconnect the LED cable from LEDCN1 on the main board.
Chapter 3 71
17. Disconnect the speaker cable from the INTSPK1 connector on the main board.
18. Remove the eleven screws (11 x A, 1 x G) from the bottom panel.

1~11 M2.5 x L8 (11) Black 3.0 kgf-cm
12 M2 x L4 (1) Black 3.0 kgf-cm
72 Chapter 3
19. Turn the unit over and remove the three screws (G) from the top panel.

1~3 M2 x L4 (3) Black 3.0 kgf-cm
20. Gently remove the upper case from the lower case.
Removing the LED Board

Chapter 3 73
15. See “Separating the Upper Case from the Lower Case” on page 70.
16. Disconnect the LED cable from the LED board.
17. Disconnect the internal microphone cable from the INTMIC1 connector on the LED board.
74 Chapter 3
18. Remove the one screw (C) securing the LED board.

19. Remove the LED board from the upper cover.
Removing the Speaker Module

Chapter 3 75
16. Remove the four screws (C) securing the speaker module.

17. Remove the tape covering the speaker cable.
76 Chapter 3
18. Release the speaker cable from the latches.
19. Remove the speaker module from the upper case.
Removing the Touchpad Module

Chapter 3 77
16. Remove the touchpad cable that is glued to the bracket.
17. Disconnect the touchpad cable from the touchpad board.
78 Chapter 3
18. Remove the two screws (C) securing the bracket to the upper case.

19. Remove the touchpad bracket.
Chapter 3 79
20. Carefully pry loose and remove the touch pad board.
WARNING:The touchpad board is glued to the upper case, only remove the touchpad board if it is defective.
Removing the Modem Board

80 Chapter 3
16. Remove the one screw (C) securing the modem card.

17. Lift the modem board from the main board.
Chapter 3 81
18. Disconnect the cable from the modem board.
Removing the Main Board

16. See “Removing the Modem Board” on page 80.
82 Chapter 3
17. Disconnect the USB cable from the USBCN1 connector on the main board.
18. Disconnect the bluetooth cable from the BLUE1 connector on the main board.
19. Remove the one screw (C) securing the main board in place.

Chapter 3 83
20. Carefully remove the main board.
Removing the USB Board Module

16. See “Removing the Modem Board” on page 80.
84 Chapter 3
17. Remove the one screw (C) securing the USB board module to the lower case.

18. Release the USB cable from the latch.
19. Remove the USB board module from the lower case.
Chapter 3 85
Removing the Bluetooth Modules
16. Remove the bluetooth module from the lower case.
NOTE: Be careful when removing the bluetooth module, because it is glued to the lower case.
86 Chapter 3
LCD Module Disassembly Process
LCD Module Disassembly Flowchart
LCD MODULE DISASSEMBLY
LCD MODULE
Bx4
LCD BEZEL
Bx5
LCD ASSEMBLY
Fx2 Fx2 LCD BACK PANEL

LCD FPC LEFT LCD RIGHT LCD
CABLE BRACKET BRACKET
ANTENNAS VGA
CAMERA
Screw List

B M2.5 x L6 Black 86.00E12.536
F M2 x L4 Silver 86.00C07.220
Chapter 3 87
Removing the LCD Bezel
10. Remove the four screw covers from the LCD bezel.
11. Remove the four screws (B) on the LCD module as shown.

1~4 M2.5 x L6 (4) Black 3.0 kgf-cm
88 Chapter 3
12. Carefully pry open the LCD bezel and place the bezel on top of the LCD panel.
Removing the LCD panel with the Brackets

10. See “Removing the LCD Bezel” on page 88.
Chapter 3 89
11. Disconnect the cable from the web camera.
12. Remove the five screws (5 x B) securing the LCD module.

1~5 M2.5 x L6 (5) Black 3.0 kgf-cm
13. Remove the LCD with the brackets from the back cover.
Removing the Inverter Board and FPC Cable

90 Chapter 3
11. See “Removing the LCD panel with the Brackets” on page 89.
12. Disconnect the cables from the inverter board.
Chapter 3 91
13. Detach any adhesive tapes and any cable that is glued to the LCD panel.
92 Chapter 3
14. Disconnect the FPC cable from the LCD panel.
Removing the LCD Brackets

12. See “Removing the Inverter Board and FPC Cable” on page 90.
13. Remove the four screws (4 x F) securing the left and right LCD brackets to remove the brackets.
Chapter 3 93
Removing the Antennas

12. Release the antenna cables from the aluminium tapes.
94 Chapter 3
13. Remove the left and right antenna cables together with the tapes holding them in place.
NOTE: There is no need to remove the antenna unless you really need to replace it.
Removing the Web Camera

Chapter 3 95
12. Remove the Web camera from the back cover.
96 Chapter 3
Chapter 4
Troubleshooting
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Go To
Power failure. (The power indicator does “Power System Check” on page 99.
not go on or stay on.)
POST does not complete. No beep or error “Power-On Self-Test (POST) Error
codes are indicated. Message” on page 102
“Undetermined Problems” on page 116
POST detects an error and displayed “Error Message List” on page 103
messages on screen.
Other symptoms (i.e. LCD display problems “Power-On Self-Test (POST) Error
or others). Message” on page 102
Symptoms cannot be re-created Use the customer-reported symptoms and
(intermittent problems). go to “Power-On Self-Test (POST) Error
Message” on page 102
“Intermittent Problems” on page 115
“Undetermined Problems” on page 116
Chapter 4 97
System Check Procedures
External Diskette Drive Check
Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is
required.
NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause
damage to the drive or cause the drive to fail.
Do the following to select the test device.
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if FDD Test is passed as the program runs to FDD Test.
3. Follow the instructions in the message window.
If an error occurs with the internal diskette drive, reconnect the diskette connector on the system board.
If the error still remains:
1. Reconnect the external diskette drive/DVD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
3. Replace the main board.
External CD-ROM Drive Check

Do the following to isolate the problem to a controller, drive, or CD-ROM. Make sure that the CD-ROM does
not have any label attached to it. The label can cause damage to the drive or can cause the drive to fail.
Do the following to select the test device:
1. Boot from the diagnostics diskette and start the diagnostics program.
2. See if CD-ROM Test is passed when the program runs to CD-ROM Test.
If an error occurs, reconnect the connector on the System board. If the error still remains:
1. Reconnect the external diskette drive/CD-ROM module.
2. Replace the external diskette drive/CD-ROM module.
Keyboard or Auxiliary Input Device Check

Remove the external keyboard if the internal keyboard is to be tested.
If the internal keyboard does not work or an unexpected character appears, make sure that the flexible cable
extending from the keyboard is correctly seated in the connector on the system board.
If the keyboard cable connection is correct, run the Keyboard Test.
If the tests detect a keyboard problem, do the following one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the keyboard cables.
2. Replace the keyboard.
The following auxiliary input devices are supported by this computer:

K Numeric keypad
98 Chapter 4
K External keyboard
If any of these devices do not work, reconnect the cable connector and repeat the failing operation.
Memory Check
Memory errors might stop system operations, show error messages on the screen, or hang the system.
1. Boot from the diagnostics diskette and start the diagnostic program (please refer to main board.
2. Go to the diagnostic memory in the test items.
3. Press F2 in the test items.
NOTE: Make sure that the DIMM is fully installed into the connector. A loose connection can cause an error.
Power System Check

To verify the symptom of the problem, power on the computer using each of the following power sources:
1. Remove the battery pack.
2. Connect the power adapter and check that power is supplied.
3. Disconnect the power adapter and install the charged battery pack; then check that power is supplied by
the battery pack.
If you suspect a power problem, see the appropriate power supply check in the following list:
K “Check the Power Adapter” on page 100
K “Check the Battery Pack” on page 101
Chapter 4 99
Check the Power Adapter
Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power
adapter cable. See the following figure
Pin 1: +19 to +20.5V

Pin 2: 0V, Ground
1. If the voltage is not correct, replace the power adapter.

2. If the voltage is within the range, do the following:
K Replace the System board.
K If the problem is not corrected, see “Undetermined Problems” on page 116.
K If the voltage is not correct, go to the next step.
NOTE: An audible noise from the power adapter does not always indicate a defect.
3. If the power-on indicator does not light up, check the power cord of the power adapter for correct
continuity and installation.
4. If the operational charge does not work, see “Check the Battery Pack” on page 101.
100 Chapter 4
Check the Battery Pack
To check the battery pack, do the following:
From Software:
1. Check out the Power Management in control Panel
2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total
Battery Power Remaining are correct.
3. Repeat the steps 1 and 2, for both battery and adapter.
4. This helps you identify first the problem is on recharging or discharging.
From Hardware:
1. Power off the computer.
2. Remove the battery pack and measure the voltage between battery terminals 1(+) and 6(ground).
3. If the voltage is still less than 7.5 Vdc after recharging, replace the battery.
To check the battery charge operation, use a discharged battery pack or a battery pack that has less than 50%
of the total power remaining when installed in the computer.
If the battery status indicator does not light up, remove the battery pack and let it return to room temperature.
Re-install the battery pack.
If the charge indicator still does not light up, replace the battery pack. If the charge indicator still does not light
up, replace the DC/DC charger board.
Touchpad Check
If the touchpad doesn’t work, do the following actions one at a time to correct the problem. Do not replace a
non-defective FRU:
1. Reconnect the touchpad cables.
2. Replace the touchpad.
3. Replace the system board.
After you use the touchpad, the pointer drifts on the screen for a short time. This self-acting pointer movement
can occur when a slight, steady pressure is applied to the touchpad pointer. This symptom is not a hardware
problem. No service actions are necessary if the pointer movement stops in a short period of time.
Chapter 4 101
Power-On Self-Test (POST) Error Message
The POST error message index lists the error message and their possible causes. The most likely cause is
listed first.
NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU
replacement does not solve the problem, put the original part back in the computer. Do not replace a
non-defective FRU.
This index can also help you determine the next possible FRU to be replaced when servicing a computer.
If the symptom is not listed, see “Undetermined Problems” on page 116.
The following lists the error messages that the BIOS displays on the screen and the error symptoms classified
by function.
NOTE: Most of the error messages occur during POST. Some of them display information about a hardware
device, e.g., the amount of memory installed. Others may indicate a problem with a device, such as the
way it has been configured.
NOTE: If the system fails after you make changes in the BIOS Setup Utility menus, reset the computer, enter
Setup and install Setup defaults or correct the error.
102 Chapter 4
Index of Error Messages
Error Code List
Error Codes Error Messages

006 Equipment Configuration Error
Causes:
1. CPU BIOS Update Code Mismatch
2. IDE Primary Channel Master Drive Error
(THe causes will be shown before “Equipment
Configuration Error”)
010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh)
070 Real Time Clock Error
071 CMOS Battery Bad
072 CMOS Checksum Error
110 System disabled.
Incorrect password is specified.
<No error code> Battery critical LOW
In this situation BIOS will issue 4 short beeps then shut
down system, no message will show.
<No error code> Thermal critical High
In this situation BIOS will shut down system, not show
message.
Error Message List
Error Messages FRU/Action in Sequence

Failure Fixed Disk Reconnect hard disk drive connector.
“Load Default Settings” in BIOS Setup Utility.
Hard disk drive
System board
Stuck Key see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard error see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard Controller Failed see “Keyboard or Auxiliary Input Device Check” on page 98.
Keyboard locked - Unlock key switch Unlock external keyboard
Monitor type does not match CMOS - Run Run “Load Default Settings” in BIOS Setup Utility.
Setup
Shadow RAM Failed at offset: nnnn BIOS ROM
System board
System RAM Failed at offset: nnnn DIMM
System board
Extended RAM Failed at offset: nnnn DIMM
System board
System battery is dead - Replace and run Replace RTC battery and Run BIOS Setup Utility to
Setup reconfigure system time, then reboot system.
System CMOS checksum bad - Default RTC battery
configuration used Run BIOS Setup Utility to reconfigure system time, then
reboot system.
Chapter 4 103
Error Message List
Error Messages FRU/Action in Sequence

System timer error RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Real time clock error RTC battery
Run BIOS Setup Utility to reconfigure system time, then
reboot system.
System board
Previous boot incomplete - Default Run “Load Default Settings” in BIOS Setup Utility.
configuration used RTC battery
System board
Memory size found by POST differed from Run “Load Default Settings” in BIOS Setup Utility.
CMOS DIMM
System board
Diskette drive A error Check the drive is defined with the proper diskette type in
BIOS Setup Utility
See “External Diskette Drive Check” on page 98.
Incorrect Drive A type - run SETUP Check the drive is defined with the proper diskette type in
BIOS Setup Utility
System cache error - Cache disabled System board
CPU ID: System board
DMA Test Failed DIMM
System board
Software NMI Failed DIMM
System board
Fail-Safe Timer NMI Failed DIMM
System board
Device Address Conflict Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Allocation Error for device Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Failing Bits: nnnn DIMM
BIOS ROM
System board
Fixed Disk n None
Invalid System Configuration Data BIOS ROM
System board
I/O device IRQ conflict Run “Load Default Settings” in BIOS Setup Utility.
RTC battery
System board
Operating system not found Enter Setup and see if fixed disk and drive A: are properly
identified.
Diskette drive
Hard disk drive
System board
104 Chapter 4
Error Message List
No beep Error Messages FRU/Action in Sequence

No beep, power-on indicator turns off and Power source (battery pack and power adapter). See “Power
LCD is blank. System Check” on page 99..
Ensure every connector is connected tightly and correctly.
Reconnect the DIMM.
LED board.
System board.
No beep, power-on indicator turns on and Power source (battery pack and power adapter). See “Power
LCD is blank. System Check” on page 99..
Reconnect the LCD connector
Hard disk drive
LCD inverter ID
LCD cable
LCD Inverter
LCD
System board
No beep, power-on indicator turns on and Reconnect the LCD connectors.
LCD is blank. But you can see POST on an LCD inverter ID
external CRT. LCD cable
LCD inverter
LCD
System board
No beep, power-on indicator turns on and a Ensure every connector is connected tightly and correctly.
blinking cursor shown on LCD during System board
POST.
No beep during POST but system runs Speaker
correctly. System board
Chapter 4 105
Phoenix BIOS Beep Codes
Code Beeps POST Routine Description

02h Verify Real Mode
03h Disable Non-Maskable Interrupt (NMI)
04h Get CPU type
06h Initialize system hardware
08h Initialize chipset with initial POST values
09h Set IN POST flag
0Ah Initialize CPU registers
0Bh Enable CPU cache
0Ch Initialize caches to initial POST values
0Eh Initialize I/O component
0Fh Initialize the local bus IDE
10h Initialize Power Management
11h Load alternate registers with initial POST
values
12h Restore CPU control word during warm
boot
13h Initialize PCI Bus Mastering devices
14h Initialize keyboard controller
16h 1-2-2-3 BIOS ROM checksum
17h Initialize cache before memory autosize
18h 8254 timer initialization
1Ah 8237 DMA controller initialization
1Ch Reset Programmable Interrupt Controller
20h 1-3-1-1 Test DRAM refresh
22h 1-3-1-3 Test 8742 Keyboard Controller
24h Set ES segment register to 4 GB
26h Enable A20 line
28h Autosize DRAM
29h Initialize POST Memory Manager
2Ah Clear 215 KB base RAM
2Ch 1-3-4-1 RAM failure on address line xxxx
2Eh 1-3-4-3 RAM failure on data bits xxxx of low byte
of memory bus
2Fh Enable cache before system BIOS
shadow
30h 1-4-1-1 RAM failure on data bits xxxx of high byte
of memory bus
32h Test CPU bus-clock frequency
33h Initialize Phoenix Dispatch Manager
36h Warm start shut down
38h Shadow system BIOS ROM
3Ah Autosize cache
106 Chapter 4
3Ch Advanced configuration of chipset
registers
3Dh Load alternate registers with CMOS
values
42h Initialize interrupt vectors
45h POST device initialization
46h 2-1-2-3 Check ROM copyright notice
48h Check video configuration against CMOS
49h Initialize PCI bus and devices
4Ah Initialize all video adapters in system
4Bh QuietBoot start (optional)
4Ch Shadow video BIOS ROM
4Eh Display BIOS copyright notice
50h Display CPU type and speed
51h Initialize EISA board
52h Test keyboard
54h Set key click if enabled
58h 2-2-3-1 Test for unexpected interrupts
59h Initialize POST display service
5Ah Display prompt “Press F2 to enter
SETUP”
5Bh Disable CPU cache
5Ch Test RAM between 512 and 640 KB
60h Test extended memory
62h Test extended memory address lines
64h Jump to User Patch1
66h Configure advanced cache registers
67h Initialize Multi Processor APIC
68h Enable external and CPU caches
69h Setup System Management Mode (SMM)
area
6Ah Display external L2 cache size
6Bh Load custom defaults (optional)
6Ch Display shadow-area message
6Eh Display possible high address for UMB
recovery
70h Display error messages
72h Check for configuration errors
76h Check for keyboard errors
7Ch Set up hardware interrupt vectors
7Eh Initialize coprocessor if present
80h Disable onboard Super I/O ports and
IRQs
81h Late POST device initialization
Chapter 4 107
82h Detect and install external RS232 ports
83h Configure non-MCD IDE controllers
84h Detect and install external parallel ports
85h Initialize PC-compatible PnP ISA devices
86h Re-initialize onboard I/O ports
87h Configure Motherboard Configurable
Devices (optional)
88h Initialize BIOS Area
89h Enable Non-Maskable Interrupts (NMIs)
8Ah Initialize Extended BIOS Data Area
8Bh Test and initialize PS/2 mouse
8Ch Initialize floppy controller
8Fh Determine number of ATA drives
(optional)
90h Initialize hard-disk controllers
91h Initialize local-bus hard-disk controllers
92h Jump to UserPatch2
93h Build MPTABLE for multi-processor
boards
95h Install CD ROM for boot
96h Clear huge ES segment register
97h Fixup Multi Processor table
98h 1-2 Search for option ROMs. One long, two
short beeps on checksum failure.
99h Check for SMART drive (optional)
9Ah Shadow option ROMs
9Ch Set up Power Management
9Dh Initialize security engine (optional)
9Eh Enable hardware interrupts
9Fh Determine number of ATA and SCSI
drives
A0h Set time of day
A2h Check key lock
A4h Initialize Typematic rate
A8h Erase F2 prompt
AAh Scan for F2 key stroke
ACh Enter SETUP
AEh Clear Boot flag
B0h Check for errors
B2h POST done- prepare to boot operating
system
B4h 1 One short beep before boot
B5h Terminate QuietBoot (optional)
B6h Check password (optional)
108 Chapter 4
B9h Prepare Boot
BAh Initialize DMI parameters
BBh Initialize PnP Option ROMs
BCh Clear parity checkers
BDh Display MultiBoot menu
BEh Clear screen (optional)
BFh Check virus and backup reminders
C0h Try to boot with INT 19
C1h Initialize POST Error Manager (PEM)
C2h Initialize error logging
C3h Initialize error display function
C4h Initialize system error handler
C5h PnPnd dual CMOS (optional)
C6h Initialize notebook docking (optional)
C7h Initialize notebook docking late
C8h Force check (optional)
C9h Extended checksum (optional)
D2h Unknown interrupt
Code Beeps
E0h Initialize the chipset
E1h Initialize the bridge
E2h Initialize the CPU
E3h Initialize the system timer
E4h Initialize system I/O
E5h Check force recovery boot
E6h Checksum BIOS ROM
E7h Go to BIOS
E8h Set Huge Segment
E9h Initialize Multi Processor
EAh Initialize OEM special code
EBh Initialize PIC and DMA
ECh Initialize Memory type
EDh Initialize Memory size
EEh Shadow Boot Block
EFh System memory test
F0h Initialize interrupt vectors
F1h Initialize Run Time Clock
F2h Initialize video
F3h Initialize System Management Mode
F4h 1 Output one beep before boot
Chapter 4 109
Code Beeps
F5h Boot to Mini DOS
F6h Clear Huge Segment
F7h Boot to Full DOS
110 Chapter 4
Index of Symptom-to-FRU Error Message
LCD-Related Symptoms
Symptom / Error Action in Sequence

LCD backlight doesn't work Enter BIOS Utility to execute “Load Setup Default Settings”,
LCD is too dark then reboot system.
LCD brightness cannot be adjusted Reconnect the LCD connectors.
LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't
work).
LCD inverter ID
LCD cable
LCD inverter
LCD
System board
Unreadable LCD screen Reconnect the LCD connector
Missing pels in characters LCD inverter ID
Abnormal screen LCD cable
Wrong color displayed LCD inverter
LCD
System board
LCD has extra horizontal or vertical lines LCD inverter ID
displayed. LCD inverter
LCD cable
LCD
System board
Indicator-Related Symptoms

Indicator incorrectly remains off or on, but Reconnect the inverter board
system runs correctly Inverter board
System board
Power-Related Symptoms

Power shuts down during operation Power source (battery pack and power adapter). See “Power
System Check” on page 99.
Battery pack
Power adapter
Hard drive & battery connection board
System board
The system doesn’t power-on. Power source (battery pack and power adapter). See “Power
Battery pack
Power adapter
Hard drive & battery connection board
System board
Chapter 4 111
Power-Related Symptoms

The system doesn’t power-off. Power source (battery pack and power adapter). See “Power
Hold and press the power switch for more than 4 seconds.
System board
Battery can’t be charged See “Check the Battery Pack” on page 101.
Battery pack
System board
PCMCIA-Related Symptoms

System cannot detect the PC Card PCMCIA slot assembly
(PCMCIA) System board
PCMCIA slot pin is damaged. PCMCIA slot assembly
Memory-Related Symptoms

Memory count (size) appears different from Enter BIOS Setup Utility to execute “Load Default Settings,
actual size. then reboot system.
DIMM
System board
Speaker-Related Symptoms

In Windows, multimedia programs, no Audio driver
sound comes from the computer. Speaker
System board
Internal speakers make noise or emit no Speaker
sound. System board
Power Management-Related Symptoms

The system will not enter hibernation See “Save to Disk (S4)” on page 32.
Keyboard (if control is from the keyboard)
Hard disk drive
System board
The system doesn't enter hibernation mode Press Fn+o and see if the computer enters hibernation
and four short beeps every minute. mode.
Touchpad
Keyboard
Hard disk connection board
Hard disk drive
System board
The system doesn’t enter standby mode See “Save to Disk (S4)” on page 32.
after closing the LCD LCD cover switch
System board
112 Chapter 4
Power Management-Related Symptoms

The system doesn't resume from See “Save to Disk (S4)” on page 32.
hibernation mode. Hard disk connection board
Hard disk drive
System board
The system doesn't resume from standby See “Save to Disk (S4)” on page 32.
mode after opening the LCD. LCD cover switch
System board
Battery fuel gauge in Windows doesn’t go Remove battery pack and let it cool for 2 hours.
higher than 90%. Refresh battery (continue use battery until power off, then
charge battery).
Battery pack
System board
System hangs intermittently. Reconnect hard disk/CD-ROM drives.
Hard disk connection board
System board
Peripheral-Related Symptoms

System configuration does not match the Enter BIOS Setup Utility to execute “Load Default Settings”,
installed devices. then reboot system.
Reconnect hard disk/CD-ROM/diskette drives.
External display does not work correctly. Press Fn+F5, LCD/CRT/Both display switching
System board
USB does not work correctly System board
Print problems. Ensure the “Parallel Port” in the “Onboard Devices
Configuration” of BIOS Setup Utility is set to Enabled.
Onboard Devices Configuration
Run printer self-test.
Printer driver
Printer cable
Printer
System Board
Serial or parallel port device problems. Ensure the “Serial Port” in the Devices Configuration” of
BIOS Setup Utility is set to Enabled.
Device driver
Device cable
Device
System board
Keyboard/Touchpad-Related Symptoms

Keyboard (one or more keys) does not Reconnect the keyboard cable.
work. Keyboard
System board
Chapter 4 113
Keyboard/Touchpad-Related Symptoms

Touchpad does not work. Reconnect touchpad cable.
Touchpad board
System board
Modem-Related Symptoms

Internal modem does not work correctly. Modem phone port
modem combo board
System board
NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined
Problems” on page 116.
114 Chapter 4
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Chapter 4 115
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power
System Check” on page 99.):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
K Non-Acer devices
K Printer, mouse, and other external devices
K Battery pack
K Hard disk drive
K DIMM
K CD-ROM/Diskette drive Module
K PC Cards
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
K System board
K LCD assembly
116 Chapter 4
Chapter 5
Jumper and Connector Locations

Top and Bottom View
Chapter 5 117
118 Chapter 5
Clearing Password Check and BIOS Recovery
This section provide you the standard operating procedures of clearing password and BIOS recovery for
Aspire 5730Z/5330 Series. Aspire 5730Z/5330 Series provide one Hardware Open Gap on main board for
clearing password check, and one Hotkey for enabling BIOS Recovery.
Clearing Password Check
Hardware Open Gap Description

Hardware Default Setting Operation Description
Gap Open (Normal) Short (Clearing Password Check)
HW Gap position on M/B space:

Gap name in Aspire 5730Z/5330 Series is G10
Steps for Clearing BIOS Password Check

If users set BIOS Password (Supervisor Password and/or User Password) for a security reason, BIOS will ask
the password during systems POST or when systems enter to BIOS Setup menu. However, once it is
necessary to bypass the password check, users need to short the HW Gap to clear the password by the
following steps:
• Power Off a system, and remove HDD, AC and Battery from the machine.
• Open the back cover of the machine, and find out the HW Gap on M/B as picture.
• Use an electric conductivity tool to short the two points of the HW Gap.
• Plug in AC, keep the short condition on the HW Gap, and press Power Button to power on the
system till BIOS POST finish. Then remove the tool from the HW Gap.
• Restart system. Press F2 key to enter BIOS Setup menu.
•If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and
try again.
NOTE: The steps are only for clearing BIOS Password (Supervisor Password and User Password).
Chapter 5 119
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block:

BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous
BIOS flashing process failed.
BIOS Recovery Hotkey:

The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered
on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and Battery
present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called Boot
Block.
Steps for BIOS Recovery by Crisis Disk:

Before doing this, one Crisis Disk should be prepared ready in hand. The Crisis Disk could be made by
executing the Crisis Disk program in another system with Windows XP OS.
Follow the steps below:
1. Power Off system.
2. Insert the Crisis Disk to a USB floppy drive which is attached to the BIOS flash failed machine.
3. In the power-off state, press Fn+Esc and hold them and then press Power Button. The system should be
powered on with Crisis BIOS Recovery process.
4. BIOS Boot Block starts to restore the BIOS code from the Crisis floppy disk to BIOS ROM on the failed
machine.
5. If the Crisis flashing process is finished, the system will restart.
If the Crisis Recovery process is finished, the system should be powered on with successful and workable
BIOS. Then a person can update the latest version BIOS for this machine by regular BIOS flashing process.
120 Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of 5730Z/5330 Series. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Chapter 6 121
Aspire 5730Z/5330 Series Exploded Diagram
122 Chapter 6
Aspire 5730Z/5330 Series FRU List
Category No. Part Name and Description Acer Part No.

ACCESSORY
REMOTE CONTROLLER FORMOSA21 RT.22700.011
RC804V-B EN
REMOTE CONTROLLER FORMOSA21 RT.22700.008
RC804V-B EU
Adapter
ADAPTER 90W LITEON PA-1900-24AR AP.09003.011
ADAPTER 90W DELTA ADP-90SB AP.09001.013
BBEA LF
ADAPTER 90W 3PIN DELTA ADP-90SB AP.09001.014
ADT 90W 19V 3P HP-OL093B13P LF AP.0900A.001
ADAPTER 65W 3PIN DELTA SADP- AP.06501.014
65KB BFJA LF
ADAPTER 65W LITEON PA-1650-02AC AP.06503.016
LF
ADAPTER 65W HIPRO HP-OK065B13 AP.0650A.010
LF
ADAPTER 65W DELTA SADP-65KB AP.06501.013
DFA LF
Battery-
SANYO AS-2007B LI-ION 3S2P SANYO BT.00603.042
6 CELL 4400MAH
SONY AS-2007B LI-ION 3S2P SONY 6 BT.00604.025
CELL 4400MAH
PANASONIC AS-2007B LI-ION 3S2P BT.00605.021
PANASONIC 6 CELL 4400MAH
SIMPLO AS-2007B LI-ION 3S2P BT.00607.016
SIMPLO AS-2007B LI-ION 4S2P BT.00807.015
Boards
EIGER AUDIO BD 07629-2M (D) 55.AR501.001
EIGER PD E KEY BD (D) 55.AR501.006
EIGER PD LAUNCH BD (D) 55.AR501.002
EIGER PD POWER BD (D) 55.AR501.007
EIGER PD USB BD WITH TV (D) 55.AQE01.001
TOUCHPAD SYNAPTICS TM00540-001 56.AGV01.001
BT MOD FOXCONN BCM2045 V2 BT.21100.005

WLAN 802.11ABGN SHIRLEYPEAK1*2 KI.SPM01.003
VGA MXM CARD NVIDIA 9PGSHM 55.AQ301.001
DDRIII 512MB W/HDCP (MSI MADE)
VGA CARD NB9P-GS/512M GDDR3
BIWA MINI SENSOR BD 07522-2M 55.TKJ01.001

EIGER PD FP BD WITH MINI (D) 55.AQ301.002
TV TUNCER DVB-T MINI TT-1260DA TU.23100.015
Chapter 6 123
CAPACITIVE BUTTON TM-01119-001 55.AR501.005
MODEM BOARD FOXCONN DELPHI- FX.22500.022
AM5 V2H 1.5_3.3V
Cables
LAUNCH BOARD CABLE 50.AR501.002
MEDIA BOARD CABLE 50.AR501.005
TOUCHPAD BOARD CABLE 50.AR501.006
USB BOARD CABLE 50.AR501.003
BLUETOOTH BOARD CABLE 50.AR501.007
AUDIO BOARD CABLE 50.AR501.001
DC-IN CABLE 90W 50.AQ301.001
TV TUNER BOARD CABLE 50.AQE01.001
TOUCHPAD BUTTON BOARD CABLE 50.AR501.004
DC-IN CABLE 65W 50.AR501.008
LCD/CAMERA CABLE 15.4" WXGA 50.AR501.009
POWER CORD 10A 125V US 27.T30V1.001
POWER CORD 10A 125V 3PIN US BK 27.01518.641
POWER CORD 2.5A 125V 8121- USA/ 27.01518.781
W CNS
POWER CORD 220V 3PIN EUR 27.T30V1.004
POWER CABLE 16A 250V 3PIN EUR 27.01518.731
UK
POWER CORD 3A 250V 3PIN UK 27.01518.541
POWER CORD 5A 250V 3PIN UK BK 27.03118.001
POWER CORD 10A 3PIN BK 27.01518.561
DENMARK
POWER CORD 10A 250V 3PIN 27.01518.671
DENMARK BK
POWER CORD 10A 250V 3PIN BK 27.01518.571
SOUTH AFRICA
POWER CORD 16A 250V SOUTH 27.01518.681
AFRICA BK
POWER CORD 10A 250V SWISS 27.01518.581
POWER CORD 10A 250V 3PIN SWISS 27.01518.691
BK
POWER CORD 10A 250V 3PIN CHINA 27.01518.591
POWER CORD 10A 250V 3PIN CHINA 27.01518.701
BK
POWER CORD 10A 250V 3PIN ITALY 27.01518.611
POWER CORD 10A 250V 3PIN ITALY 27.01518.711
BK
POWER CORD 2.5A 250V SOUTH 27.01518.631
AFRICA BK (INDIA)
POWER CORD 10A 250V SOUTH 27.01518.721
AFRICA BK (INDIA)
POWER CORD 2.5A 250V AUSTRALIA 27.01518.621
POWER CORD ACA/ACNZ 27.03218.021
POWER CORD 7A 125V 2PIN JAPEN 27.01518.551
POWER CORD 7A 125V 2PIN JAPAN 27.03518.161
POWER CORD 7A 250V 2PIN KOREA 27.01518.531
124 Chapter 6
POWER CORD 250V 10A 3PIN ISRAEL 27.01518.761
Case/Cover/Bracket/Assembly
LOWER CASE W/MODEM CABLE&FAN 60.AQE01.001
BRACKET&SPEAKER FOR TV
SPEAKER SUB WOFFER 23.AR501.001
SPEAKER SET 23.AR501.002
EXPRESS DUMMY CARD 42.AR501.004
NEW CARD DUMMY CARD 42.TK901.005
SD DUMMY CARD 42.TK901.006
MIDDLE COVER 42.AR501.001
UNITLOAD COVER 42.AR501.002
E-KEY COVER 42.AR501.003
TOUCHPAD BRACKET 33.AR501.001
VGA BOARD BARCKET FOR NVIDIA 33.TPE01.001
UPPER CASE W/SPEAKER&E KEY 60.AQ301.002
CABLE&POWER
CABLE&FINGERPRINT HOLE
OPTICAL BRACKET 33.AR501.002
BD COMBO BEZEL 42.AR501.005
SUPER MULIT BEZEL 42.AGV01.005
HDD BRACKET 33.AR501.003
LCD COVER 15.4" W/BACKLIGHT 60.AR501.005
MODULE&ANTENNA
LCD BEZEL 15.4" W/MICROPHONE 60.AR501.004
LCD BRACKET W/HINGE LEFT 33.AR501.004
LCD BRACKET W/HINGE RIGHT 33.AR501.005
Combo Module
COMBO MODULE BLU-RAY 2X 6M.AR501.001
ODD SONY BD COMBO 12.7MM TRAY KO.0020E.002

DL 2X BC-5500S LF W/O BEZEL SATA
Communication Module
EXTERNAL ANTENNA SET 25.AQE01.001
CPU/Processor
Chapter 6 125
CPU INTEL CORE2DUAL P8400 PGA KC.84001.DPP
2.26G 3M 1066 25W
2.4G 1066 25W 3M
2.53G 6M 1066 25W
CPU INTEL CORE2DUAL T9400 PGA KC.94001.DTP
2.53G 6M 1066 35W
CPU INTEL CORE2DUAL T9600 PGA KC.96001.DTP
2.8G 6M 1066 35W
DVD Module
ODD TOSHIBA SUPER-MULTI DRIVE KU.00801.021
12.7MM TRAY DL 8X TS-L633A LF W/O
BEZEL SATA
ODD PIONEER SUPER-MULTI DRIVE KU.00805.044
12.7MM TRAY DL 8X DVR-TD08RS LF
W/O BEZEL SATA
ODD PANASONIC SUPER-MULTI KU.00807.059
DRIVE 12.7MM TRAY DL 8X UJ-870A
LF W/O BEZEL SATA
ODD HLDS SUPER-MULTI DRIVE KU.0080D.029
12.7MM TRAY DL 8X GSA-T50N LF W/
O BEZEL SATA
ODD HLDS SUPER-MULTI DRIVE KU.0080D.034
12.7MM TRAY DL 8X GSA-T50N LF W/
O BEZEL SATA MALAYSIA
ODD SONY SUPER-MULTI DRIVE KU.0080E.009
12.7MM TRAY DL 8X AD-7560S LF W/O
BEZEL SATA
ODD PLDS SUPER-MULTI DRIVE KU.0080F.001
12.7MM TRAY DL 8X DS-8A2S LF W/O
BEZEL SATA
Fan
FAN SUNON 23.AR501.003
Heatsink
CPU HEATSINK AVC NB9 W/O FAN 60.AQ301.003
HDD/Hard Disk Drive
126 Chapter 6
HDD 120GB 5400RPM SATA II HGST KH.12007.014
HTS542512K9SA00 BRONCO-B LF
HDD 120GB 5400RPM SATA SEAGATE KH.12001.032
ST9120817AS LF
HDD 120GB 5400RPM SATA TOSHIBA KH.12004.007
MK1246GSX LF
HDD 120GB 5400RPM SATA WD KH.12008.019
WD1200BEVS-22UST0 ML125 LF
HDD 160GB WD WD1600BEVT-22ZCT0 KH.16008.022
HDD 160GB 5400RPM SATA II HITACHI KH.16007.016
HTS541616J9SA00 LF
HDD 160GB SEAGATE SATA KH.16001.029
ST9160827AS
MK1646GSX LF
HDD 250GB SEAGATE SATA KH.25001.011
ST9250827AS
MK2546GSX LF
HDD 250GB 5400RPM SATA II HGST KH.25007.011
HTS542525K9SA00 LF
WD2500BEVS-22UST0 ML125
WD3200BEVT-22ZCT0 ML125
Keyboard
KEYBOARD 14_15KB-FV3 BLACK KB.INT00.442
E88KS US INTERNATIONAL (ASPIRE
BLACK)
E88KS US INTERNATIONAL HEBREW
(ASPIRE BLACK)
E89KS UK (ASPIRE BLACK)
E89KS TURKISH (ASPIRE BLACK)
E88KS THAILAND (ASPIRE BLACK)
E89KS SWISS/G (ASPIRE BLACK)
E89KS SWEDISH (ASPIRE BLACK)
E89KS SPANISH (ASPIRE BLACK)
89KS SLO/CRO (ASPIRE BLACK)
E88KS RUSSIAN (ASPIRE BLACK)
E89KS PORTUGUESE (ASPIRE
BLACK)
E89KS POLISH (ASPIRE BLACK)
Chapter 6 127
E89KS NORWEGIAN (ASPIRE BLACK)
E88KS KOREAN (ASPIRE BLACK)
E93KS JAPANESE (ASPIRE BLACK)
E89KS ITALIAN (ASPIRE BLACK)
E89KS HUNGARIAN (ASPIRE BLACK)
E88KS GREEK (ASPIRE BLACK)
E89KS GERMAN (ASPIRE BLACK)
E89KS FRENCH (ASPIRE BLACK)
E89KS DUTCH (ASPIRE BLACK)
E89KS DANISH (ASPIRE BLACK)
E89KS CZECH (ASPIRE BLACK)
E88KS TRADITIONAL CHINESE
(ASPIRE BLACK)
E89KS CANADIAN FRENCH (ASPIRE
BLACK)
E89KS BRAZILIAN PORTUGUESE
(ASPIRE BLACK)
E89KS BELGIUM (ASPIRE BLACK)
E88KS ARABIC/ENGLISH (ASPIRE
BLACK)
E89KS ARABIC/FRENCH (ASPIRE
BLACK)
E89KS NORDIC (ASPIRE BLACK)
E89KS ENGLISH/CANADIAN FRENCH
(ASPIRE BLACK)
LCD Module
LCD CMO 15.4" WXGA GLARE N154I3- LK.1540D.022
L03 LF 220NIT 8MS
LCD AUO 15.4" WXGA GLARE LK.15405.028
B154EW02-V7 W/O BRACKET, H/W
CODE 3A LF 220NIT 8MS
LCD AUO 15.4" WXGA GLARE LK.15405.029
B154EW08-V1 W/O BRACKET, HW 3A
LF 220NIT 8MS
LCD LPL 15.4" WXGA GLARE LK.15408.029
LP154WX4-TLB4 LF 220NIT 8MS
128 Chapter 6
MAINBOARD
MAINBOARD AS5930G INTEL LF MB.AQ201.001
PGM45 ICH9 LF FOR MONTEVINA
CPU WITH PR_ESATA
MAINBOARD AS5930 INTEL LF GM45 MB.AR501.001
ICH9 LF FOR MONTEVINA CPU WITH
PR_ESATA
MEMORY
SODIMM 1GB DDRII667 HYNIX KN.1GB0G.012
HYMP112S64CP6-Y5 LF
SODIMM 1GB DDRII667 SAMSUNG KN.1GB0B.016
M470T2864QZ3-CE6
SODIMM 1GB DDRII667 INFINEON KN.1GB02.036
HYS64T128021EDL-3S LF
SODIMM 1GB DDRII667 NANYA KN.1GB03.014
NT1GT64U8HB0BN-3C LF (0.09U)
SODIMM 2GB DDRII667 ELPIDA KN.2GB09.001
EBE21UE8ACUA-6E-E LF
SODIMM 2GB DDRII667 HYNIX KN.2GB0G.004
HYMP125S64CP8-Y5 LF
SODIMM 2GB DDRII667 SAMSUNG KN.2GB0B.003
M470T5663QZ3-CE6 LF
SODIMM 2GB DDRII667 MICRON KN.2GB04.001
MT16HTF25664HY-667E1 LF
SODIMM 512MB DDRII667 HYNIX KN.5120G.024
HYMP164S64CP6-Y5 LF
SODIMM 512MB DDRII667 NANYA KN.51203.032
NT512T64UH8B0FN-3C LF
SODIMM 512MB DDRII667 SAMSUNG KN.5120B.026
M470T6464QZ3-CE6 LF
MISCELLANEOUS
NAME PLATE AS5930 47.AR501.001
LOGO PLATE FOR LCD PANEL 47.AR501.002
SCREW
IMS M2X4(H=0.3) 86.00E13.524
SCREW M2*L3 NYLOK CR 3+ 86.00E25.723
SCREW M2-3 86.9A522.3R0
ISO M2.5X6(H=0.7~0.8MM) 86.00E12.536
M2.5*L10 BLACK ZN 86.00F84.73A
SCREW MACH WAFER M3*L4 NI 86.9A524.4R0
Chapter 6 129
Appendix A
Model Definition and Configuration

Aspire 5730Z/5330 Series
Acer
DIMM DIMM HDD 1 Wireless Blueto VOIP
Model RO Country Part Description CPU LCD ODD
1 2 (GB) LAN oth Phone
no
AS5730 EMEA Germany LX.AU AS5730- C2DP N15.4 SO1G SO1G N160 NSM8 SP1x2M N N
- P0X.0 732G16Mn 7350 WXGA BII6 BII6 GB5.4 XS MW
732G16 01 VHP32ATD G8 KS
Mn E1 MC
UMACE
2*1G/160/
6L/5R/
CB_n2_0.3
D_HG_DE1
3
AS5730 PA Canada LX.AU AS5730Z- PMDT N15.4 SO2G N N160 NSM8 3rd WiFi N N
Z- G0X.0 322G16Mn 3200 WXGA BII6 GB5.4 X 1x2 BGN
322G16 17 VHP32ATC G8 KS
Mn A2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_FR35
Mn A2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_FR33
Mn A2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_FR32
Mn A2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_FR31
Mn A2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_FR34
Appendix A 130
Acer
no
AS5730 PA USA LX.AU AS5730Z- PMDT N15.4 SO2G N N160 NSM8 3rd WiFi N N
Z- G0X.0 322G16Mn 3200 WXGA BII6 GB5.4 XS 1x2 BGN
322G16 12 VHP32ATU G8 KS
Mn S1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_EN33
Mn S1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_EN35
Mn S1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_EN32
Mn S1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_EN34
AS5730 PA ACLA- LX.AU AS5730Z- PMDT N15.4 SO2G N N160 NSM8 3rd WiFi N N
Z- Portuguese G0X.0 322G16Mn 3200 WXGA BII6 GB5.4 X 1x2 BGN
322G16 08 VHP32ATX G8 KS
Mn C2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_XC22
322G16 07 EM G8 KS
Mn VHP32ATX
C2 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_XC21
322G16 06 EM G8 KS
Mn VHP32ATX
C1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_XC22
131 Appendix A
Acer
no
Mn C1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_XC21
Z- Spanish G0X.0 322G16Mn 3200 WXGA BII6 GB5.4 X 1x2 BGN
322G16 04 VHP32ATE G8 KS
Mn A3 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_ES21
322G16 03 EM G8 KS
Mn VHP32ATE
A3 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_ES22
322G16 02 EM G8 KS
Mn VHP32ATE
A1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_ES22
Mn A1 MC
UMAE
1*2G/160/
6L/5R/
CB_bgn_H
G_ES21
AS5730 PA Canada LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Z- E0X.1 323G25Mn 3200 WXGA BII6 BII6 GB5.4 XS 1x2 BGN
Mn A2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR3
5
Z- E0X.1 323G25Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
Mn A2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR3
3
Appendix A 132
Acer
no
Mn A2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR3
2
Mn A2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR3
1
AS5730 EMEA France LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Z- E0Y.0 323G25Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G25 01 VHB32ATF G8 KS
Mn R1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
Mn A2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_FR3
4
AS5730 PA USA LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Mn S1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN3
3
Mn S1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN3
5
Mn S1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN3
2
133 Appendix A
Acer
no
Mn S1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN3
4
AS5730 EMEA South LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- Africa E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 37 EM G8 KS
Mn VHP32ATZ
A2 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
6
323G32 34 EM G8 KS
Mn VHP32ATZ
A1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
AS5730 EMEA Denmark LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn K1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_NO1
3
323G32 36 VHP32ATF G8 KS
Mn R1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
AS5730 EMEA Germany LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn E1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_DE1
3
AS5730 PA ACLA- LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Z- Portuguese E0X.1 323G25Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
Mn C2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_XC2
2
Appendix A 134
Acer
no
323G25 99 EM G8 KS
Mn VHP32ATX
C2 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_XC2
1
323G25 98 EM G8 KS
Mn VHP32ATX
C1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_XC2
2
Mn C1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_XC2
1
Z- Spanish E0X.0 323G25Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
Mn A3 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ES2
1
323G25 95 EM G8 KS
Mn VHP32ATE
A3 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
323G25 94 EM G8 KS
Mn VHP32ATE
A1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
135 Appendix A
Acer
no
Mn A1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ES2
1
AS5730 EMEA Belgium LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 32 VHP32ATB G8 KS
Mn E1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_NL1
3
AS5730 EMEA Holland LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 31 VHP32ATN G8 KS
Mn L1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_NL1
2
AS5730 EMEA Luxembour LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- g E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 27 VHP32ATL G8 KS
Mn U1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_IT42
AS5730 EMEA Norway LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn O1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_NO1
2
AS5730 EMEA Russia LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- E0X.0 323G32Mi 3200 WXGA BII6 BII6 GB5.4 X BG
323G32 29 VHP32ATR G8 KS
Mi U1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bg_0.3
D_HG_RU1
1
AS5730 EMEA Sweden/ LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- Finland E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 30 VHP32ATS G8 KS
Mn E1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FI12
Appendix A 136
Acer
no
AS5730 EMEA Czech LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn Z2 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_SK1
1
AS5730 EMEA Eastern LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- Europe E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
Mn U7 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_ENG
1
AS5730 AAP Australia/ LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Z- New E0X.0 323G25Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 Zealand 92 VHP32ATA G8 KS
Mn U1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5730 AAP Singapore LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
Mn G1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
Mn G1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ZH3
1
323G32 89 EM G8 KS
Mn VHP32ATS
G1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
AS5730 AAP India LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G32 88 VHP32ATIN G8 KS
Mn 1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
137 Appendix A
Acer
no
AS5730 AAP Indonesia LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G32 87 VHP32ATID G8 KS
Mn 1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ID21
323G32 86 EM G8 KS
Mn VHP32ATID
1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_ID22
323G32 85 VHP32ATID G8 KS
Mn 1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
Mn U6 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_CS2
1
Mn U3 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_RU1
1
Mn U1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_CS2
1
Mn U4 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FI12
Appendix A 138
Acer
no
Mn U3 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_RU2
1
Mn U5 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_PL11
AS5730 EMEA Hungary LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 17 VHP32ATH G8 KS
Mn U1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_HU1
1
AS5730 EMEA Slovenia/ LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- Croatia E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 18 VHP32ATSI G8 KS
Mn 1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
323G25 84 EM G8 KS
Mn VHP32ATID
1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
AS5730 AAP Philippines LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 82 VHP32ATP G8 KS
Mn H1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
AS5730 AAP Philippines LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 81 EM G8 KS
Mn VHP32ATP
H1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
139 Appendix A
Acer
no
AS5730 AAP Malaysia LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 80 VHP32ATM G8 KS
Mn Y1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
AS5730 AAP Malaysia LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 79 EM G8 KS
Mn VHP32ATM
Y1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
AS5730 AAP Thailand LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 78 VHP32ATT G8 KS
Mn H1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_TH2
1
AS5730 AAP Thailand LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 77 EM G8 KS
Mn VHP32ATT
H1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_TH2
2
AS5730 EMEA Portugal LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 14 VHP32ATPT G8 KS
Mn 1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_PT1
2
AS5730 EMEA Spain LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn S1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
AS5730 EMEA Greece LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 16 VHP32ATG G8 KS
Mn R1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EL3
2
Appendix A 140
Acer
no
Mn R1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EL2
2
AS5730 EMEA Israel LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 12 VHP32ATIL G8 KS
Mn 1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_HE1
1
AS5730 EMEA Italy LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 11 VHP32ATIT G8 KS
Mn 1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_IT12
AS5730 EMEA Turkey LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
323G32 07 EM G8 KS
Mn VHP32ATT
R1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_TR3
2
AS5730 EMEA Middle LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Z- East E0X.0 323G32Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
323G32 08 EM G8 KS
Mn VHP32ATM
E9 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FR2
2
AS5730 AAP Vietnam LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 76 VHP32ATV G8 KS
Mn N1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5730 AAP Vietnam LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N250 NSM8 3rd WiFi N N
323G25 75 EM G8 KS
Mn VHP32ATV
N1 MC
UMACE
2G+1G/250/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
141 Appendix A
Acer
no
323G32 09 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_AR1
3
323G32 10 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
5
323G32 04 EM G8 KS
Mn VHP32ATM
E3 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
323G32 05 EM G8 KS
Mn VHP32ATM
E6 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
5
323G32 06 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_AR2
3
323G32 03 EM G8 KS
Mn VHP32ATM
E4 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
1
Appendix A 142
Acer
no
AS5730 EMEA Switzerland LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn H1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_IT42
AS5730 EMEA UK LX.AU AS5730Z- PMDT N15.4 SO2G SO1G N320 NSM8 3rd WiFi N N
Mn B1 MC
UMACE
2G+1G/320/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
Z- Africa E0X.0 322G16Mn 3200 WXGA BII6 BII6 GB5.4 XS 1x2 BGN
322G16 74 EM G8 KS
Mn VHP32ATZ
A2 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
6
322G16 73 EM G8 KS
Mn VHP32ATZ
A1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
AS5730 EMEA Denmark LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn K1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_NO1
3
322G16 71 VHP32ATF G8 KS
Mn R1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
AS5730 EMEA Germany LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn E1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_DE1
3
143 Appendix A
Acer
no
AS5730 EMEA Belgium LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 69 VHP32ATB G8 KS
Mn E1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_NL1
3
AS5730 EMEA Holland LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn L1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_NL1
2
AS5730 EMEA Luxembour LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Z- g E0X.0 322G16Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
322G16 67 VHP32ATL G8 KS
Mn U1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_IT42
AS5730 EMEA Norway LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn O1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_NO1
2
AS5730 EMEA Russia LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Z- E0X.0 322G16Mi 3200 WXGA BII6 BII6 GB5.4 X BG
322G16 65 VHP32ATR G8 KS
Mi U1 MC
UMACE
2*1G/160/
6L/5R/
CB_bg_0.3
D_HG_RU1
1
AS5730 EMEA Sweden/ LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Z- Finland E0X.0 322G16Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
Mn E1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FI12
AS5730 EMEA Czech LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn Z2 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_SK1
1
Appendix A 144
Acer
no
Z- Europe E0X.0 322G16Mn 3200 WXGA BII6 BII6 GB5.4 XS 1x2 BGN
Mn U7 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_ENG
1
Mn U6 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_CS2
1
Mn U3 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_RU1
1
Mn U1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_CS2
1
Mn U4 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FI12
Mn U3 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_RU2
1
Mn U5 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_PL11
145 Appendix A
Acer
no
AS5730 EMEA Hungary LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 55 VHP32ATH G8 KS
Mn U1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_HU1
1
AS5730 EMEA Slovenia/ LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Z- Croatia E0X.0 322G16Mn 3200 WXGA BII6 BII6 GB5.4 X 1x2 BGN
322G16 54 VHP32ATSI G8 KS
Mn 1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5730 EMEA Portugal LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 53 VHP32ATPT G8 KS
Mn 1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_PT1
2
AS5730 EMEA Spain LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn S1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
Mn R1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EL3
2
Mn R1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EL2
2
AS5730 EMEA Israel LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 49 VHP32ATIL G8 KS
Mn 1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_HE1
1
Appendix A 146
Acer
no
AS5730 EMEA Italy LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 48 VHP32ATIT G8 KS
Mn 1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_IT12
AS5730 EMEA Turkey LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
322G16 47 EM G8 KS
Mn VHP32ATT
R1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_TR3
2
322G16 46 EM G8 KS
Mn VHP32ATM
E9 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FR2
2
322G16 45 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_AR1
3
322G16 44 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
5
322G16 43 EM G8 KS
Mn VHP32ATM
E3 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_FR2
3
147 Appendix A
Acer
no
322G16 42 EM G8 KS
Mn VHP32ATM
E6 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
5
322G16 41 EM G8 KS
Mn VHP32ATM
E2 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_AR2
3
322G16 40 EM G8 KS
Mn VHP32ATM
E4 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
1
AS5730 EMEA Switzerland LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn H1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_IT42
AS5730 EMEA UK LX.AU AS5730Z- PMDT N15.4 SO1G SO1G N160 NSM8 3rd WiFi N N
Mn B1 MC
UMACE
2*1G/160/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
AS5330 WW WW S2.AS AS5330- CM58 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- J0X.00 581G12Mi 5 WXGA BII6 GB5.4 X BG
581G12 1 VHP32AW G8 KS
Mi W1 MC
UMAC
1*1G/120/
BT/6L/5R/
CB_bg_0.3
D_HG_EN1
1
AS5330 AAP Thailand LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- J0Y.02 571G12Mn 5 WXGA BII6 GB5.4 X 1x2 BGN
571G12 1 VHB32ATT G8 KS
Mn H1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_TH2
1
Appendix A 148
Acer
no
AS5330 AAP Thailand LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 0 EM G8 KS
Mn VHB32ATT
H1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_TH2
2
AS5330 AAP Vietnam LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 9 VHB32ATV G8 KS
Mn N1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5330 AAP Vietnam LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 5 EM G8 KS
Mn VHB32ATV
N1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
AS5330 PA Canada LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 4 VHB32ATC G8 KS
Mn A2 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_FR3
2
AS5330 PA Canada LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 3 VHB32ATC G8 KS
Mn A2 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_FR3
1
AS5330 PA USA LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 2 VHB32ATU G8 KS
Mn S1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN3
4
Mn S1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN3
3
149 Appendix A
Acer
no
Mn S1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN3
2
AS5330 PA ACLA- LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- Portuguese J0Y.02 571G12Mn 5 WXGA BII6 GB5.4 X 1x2 BGN
571G12 9 EM G8 KS
Mn VHB32ATX
C2 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_XC2
1
- Portuguese J0Y.02 571G12Mn 5 WXGA BII6 GB5.4 XS 1x2 BGN
571G12 8 VHB32ATX G8 KS
Mn C2 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_XC2
2
571G12 7 EM G8 KS
Mn VHB32ATX
C1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_XC2
2
571G12 6 VHB32ATX G8 KS
Mn C1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_XC2
1
- Spanish J0Y.02 571G12Mn 5 WXGA BII6 GB5.4 X 1x2 BGN
571G12 5 VHB32ATE G8 KS
Mn A3 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ES2
1
571G12 4 EM G8 KS
Mn VHB32ATE
A3 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
Appendix A 150
Acer
no
571G12 3 EM G8 KS
Mn VHB32ATE
A1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ES2
2
571G12 2 VHB32ATE G8 KS
Mn A1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ES2
1
AS5330 AAP Australia/ LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- New J0Y.01 571G12Mn 5 WXGA BII6 GB5.4 X 1x2 BGN
571G12 Zealand 8 VHB32ATA G8 KS
Mn U1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5330 AAP New LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- Zealand J0Y.01 571G12Mn 5 WXGA BII6 GB5.4 X 1x2 BGN
571G12 7 VHB32ATN G8 KS
Mn Z1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
1
AS5330 AAP Singapore LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 6 VHB32ATS G8 KS
Mn G1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
571G12 4 EM G8 KS
Mn VHB32ATS
G1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
571G12 3 VHB32ATS G8 KS
Mn G1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ZH3
1
151 Appendix A
Acer
no
AS5330 AAP India LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
- J0Y.01 571G12Mn 5 WXGA BII6 GB5.4 XS 1x2 BGN
571G12 2 VHB32ATIN G8 KS
Mn 1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
2
AS5330 AAP Indonesia LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 1 VHB32ATID G8 KS
Mn 1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
571G12 0 EM G8 KS
Mn VHB32ATID
1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
571G12 9 EM G8 KS
Mn VHB32ATID
1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ID22
571G12 8 VHB32ATID G8 KS
Mn 1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ID21
AS5330 AAP Philippines LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 6 VHB32ATP G8 KS
Mn H1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
AS5330 AAP Philippines LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 5 EM G8 KS
Mn VHB32ATP
H1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
Appendix A 152
Acer
no
AS5330 AAP Malaysia LX.AS AS5330- CM57 N15.4 SO1G N N120 NSM8 3rd WiFi N N
571G12 4 VHB32ATM G8 KS
Mn Y1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
3
571G12 3 VHB32ATM G8 KS
Mn Y1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ENC
1
571G12 2 EM G8 KS
Mn VHB32ATM
Y1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_EN1
4
571G12 1 EM G8 KS
Mn VHB32ATM
Y1 MC
UMACE
1*1G/120/
6L/5R/
CB_bgn_0.3
D_HG_ENC
2
153 Appendix A
Appendix A 154
Appendix B
Test Compatible Components

This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Aspire 5730Z/5330 series
Compatibility Test Report released by the Acer Mobile System Testing Department.
Appendix B 155
Microsoft® Windows® Vista Environment Test
Item Specification
CRT Port Test
CRT Monitor Acer 211c 21”, ViewSonic G220F, ViewSonic PF790 19”
LCD Monitor Acer FP751 17” TFT LCD, Acer AL1521, Acer AL1721, ViewSonic VD201b,
Westinghouse W37G, HP LP2065, HP S9500
Projector Dell 3300MP
USB Port Test
USB Keyboard/Mouse Microsoft Natural Keyboard Pro
Dell USB Keyboard
Logicool USB Mouse (OWCM-USB)
Logitech USB Wheel Mouse
Logitech First Wheel Mouse
Dell by Logitech
Dell Internet Navigator Keyboard
Dell Smart Card Keyboard
HP USB Optical Austin Mouse
Belkin Miniglow Optical USB Mouse
HP USB Optical Mouse (RB129AA)
USB Speaker/Joystick Aiwa Multimedia Digital Speaker (SC-UC78)
Panasonic USB Speaker EAB-MPC57USB
USB Storage Drive Iomega USB Zip 250MB
Transcend 80G HDD
Plextor DVD+R/RW
LG DVD+R/RW
Sony DVD+R/RW
USB Camera Intel Easy PC Camera (A20953-001)
Orange Micro USB 2.0 Web Cam
USB HUB and Others A TEN UH-204
IOGEAR 4-Port Hub
Corega CG-WLUSBST11
USB Printer/Scanner HP 450WBT Deskjet Printer
USB Flash Drive Sony Memory Key 128MB
Sony Micro Vault Pro USD-5G
IBM 128MB Memory Key
IBM 512MB Memory Key
Apacer Handy Drive
Apacer The USB Flash Drive 256MB
USB ODD Logitec CDRW+DVDROM combo
LG DVD+R/RW
Sony DVD+R/RW
1394 Camera Sony DV-TRV10
Access Point 802.11a Intel Pro/Wireless 5000
NetGear HE 102
Access Point 802.11g D-Link Building Networks People WiFi Certified a/b/g Wireless 108AG
Access Point 802.11n Belkin N1MIMO Wireless Router High Performance wireless 802.11n
Bluetooth Device Sony Ericsson Wireless Headset
Sony Ericsson T610
X Bridge Bluetooth Access Point BT300
156 Appendix B
Item Specification
PCMCIA Test
LAN/Modem Card TDK CardBus Ethernet 10/100 32-Bit CBE-10/100BTX
Storage Card Hitachi Microdrive 4G
1394 Card Buffalo 1394 Interface Cardbus (IFC-ILCB/DV)
USB2.0 Card IBM EtherJet CardBus Adapter 10/100
Wireless Lan Card Cisco Wireless LAN Card 802.11a
(Not recommended for wireless ready NETGEAR Wireless LAN card 802.11a
model)
ISDN Card Toshiba Type B for Bluetooth 128K ISDN Card
GPRS Card Vodafone QL1ACC-21581 3G/GPRS card
Sony Ericsson GC83 GPRS card
Sony Ericsson GC89 GPRS card
ExpressCard Test
Express Card Abcom 5-in-1 Adapter ExpressCard Reader
Abcom GigaLan ExpressCard
Sunix ECF2400 2 Ports 1394A ExpressCard
Memory Card Test (SD/MS/MMC/SM/CF/Microdrive/XD)
SD Card Apacer 128/256MB
SanDisk 256MB
Apacer 2GB (150x Hi-Speed)
KINGMAX 1GB (66x Hi-Speed)
SanDisk 1GB
RiDATA 4GB SD PRO Memory Card
MS Card Sony 512 MS PRO
Lexar 512MB MS PRO
Lexar 1GB MS PRO
Sony 2GB MS PRO
MMC Card SanDisk 32MB
Transcend 64/128MB
Transcend 256MB
SanDisk RS-MMC 128MB
PQI RS-MMC 256MB
Transcend 512MB
A-DATA Turbo 200X 2GB MMC Card
XD Card Apacer 256/512MB
SanDisk 2GB
Olympus 512MB
CF Card Apacer 256/512
SanDisk 2GB
Appendix B 157
158 Appendix B
Appendix C
Online Support Information

This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
K Service guides for all models
K User's manuals
K Training materials
K Bios updates
K Software utilities
K Spare parts lists
K TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
K Detailed information on Acer's International Traveller’s Warranty (ITW)
K Returned material authorization procedures
K An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C 159
160 Appendix C
Index
A Features 1
44
Flash Utility
AFLASH Utility 44
fpc cable 90
Antennas 94
FRU (Field Replaceable Unit) List 121
Audio 30
H
B
Hard disk 28
Battery Pack 50
Hard Disk Drive Module 56
BIOS 26
vendor 26
HDD 28
Version 26 Hibernation mode
BIOS Utility33–44 hotkey13
Navigating 34 Hot Keys 11
Onboard Device Configuration 39
Security 37, 38 I
System Security 43
Indicators 9
Board Layout
Intermittent Problems 115
Top View 117
brightness J
hotkeys 13
Jumper and Connector Locations 117
C Top View 117
caps lock K
on indicator 9
computer Keyboard 30, 63
on indicator 9 Keyboard or Auxiliary Input Device Check 98
CPU 66 L
CPU Fan True Value Table 26
LCD Bezel 88
D LCD Brackets 93
DIMM Module 53 LCD Module Disassembly
Display 3 Flowchart 87
display LCD with the Brackets 89
hotkeys 13 lower cover 52
E M
Error Symptom-to-Spare Part Index 102 Main Unit Disassembly
Euro 14 Flowchart 61
Mainboard 82
External CD-ROM Drive Check 98
media access
External Module Disassembly
9
on indicator
Flowchart 49
Memory Check 99
F
161
130
Model Definition V
Modem Board 80
view
N left 6
rear 7
Notebook Manager right 6
hotkey 13
W
num lock
on indicator 9 Windows 2000 Environment Test 156
O WLAN Board 54
Online Support Information 159

P
Panel 4
Bottom 8
left 4
PC Card 9
Power System Check 99
Battery Pack 101
Power Adapter 100
Processor 26
S
Screw List 48
speakers
hotkey 13
System
Block Diagram 3
System Check Procedures 98
System Memory 26
System Utilities 33
T
Test Compatible Components 155
Top 117
touchpad
hotkey 13
Touchpad Check 101
Troubleshooting 97
U
Undetermined Problems 116
utility
BIOS 33–44
162

Aspire 5730z 5330 PDF

Uploaded by

Copyright:

Available Formats

Aspire 5730z 5330 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Aspire 5730z 5330 PDF

Uploaded by

Copyright:

Available Formats

Aspire 5730Z/5330 Series

Service guide files and updates are available

Date Chapter Updates

Acer is a registered trademark of Acer Corporation.

SCREEN MESSAGES Denotes actual messages that appear

Display and graphics

Special keys and controls

Icon Item Description

4 Speakers Left and right speakers deliver stereo audio output.

13 Keyboard For entering data into your computer.

1 Acer PureZone Two internal stereo microphones for sound recording.

Closed Front View

Icon Item Description

# Icon Item Description

2 DC-in jack Connects to an AC adapter.

3 Ethernet (RJ-45) Connects to an Ethernet 10/100/1000-based network.

4 External display Connects to a display device

Headphones/ Connects to audio line-out devices (e.g., speakers,

Icon Item Description

6 Modem (RJ-11) port Connects to a phone line.

# Icon Item Description

Icon Item Description

2 Battery lock Locks the battery in position.

3 Battery release Releases the battery for removal.

4 Memory Houses the computer's main memory.

6 Ventilation slots Enable the computer to stay cool, even after

Num Lock Lights up when Num Lock is

Icon Function Description

Lock Keys and embedded numeric keypad

Lock key Description

Desired access Num Lock on Num Lock off

Hotkey Icon Function Description

<Fn> + <F2> Acer eSettings Launches Acer eSettings in Acer Empowering

<Fn> + <F8> Speaker toggle Turns the speakers on and off.

<Fn> + < > Brightness up Increases the screen brightness.

<Fn> + < > Brightness down Decreases the screen brightness.

<Fn> + < > Volume up Increases the sound volume

The Euro symbol

The US dollar sign

Launching Acer Empowering Technology

To launch Acer Empowering Technology applications:

To set the Empowering Technology password:

Using power plans

To create a new power plan:

To switch between power plans:

To edit a power plan:

To delete a power plan:

Acer eDataSecurity Management (only for certain models)

Acer eRecovery Management

K Use the shortcut key < > + <X>.

K Start Windows Mobility Center from the Control panel.

AcerGridVista is simple to set up:

CPU Fan True Value Table

DTS(degree C) Fan Speed (rpm) Acoustic Level (dBA)

Throttling 50%: On= 99 ° C; OFF=93 ° C

OS shut down at 105 ° C; H/W shot down at 110 ° .C

Slot 1 Slot 2 Total Memory

Wireless Module 802.11b/g

Hard Disk Drive Interface