Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
136 views

Stacker Raspberry Pi

The document provides step-by-step instructions for installing Repetier-Server on a Raspberry Pi to enable remote monitoring and control of a 3D printer. It describes downloading Raspbian OS, writing it to an SD card, setting up the Raspberry Pi by expanding storage and changing time zone/password. It then guides connecting to a LAN, updating the system, downloading and installing Repetier-Server, and accessing it through a web browser to configure and control the 3D printer remotely over the network.

Uploaded by

JederVieira
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
136 views

Stacker Raspberry Pi

The document provides step-by-step instructions for installing Repetier-Server on a Raspberry Pi to enable remote monitoring and control of a 3D printer. It describes downloading Raspbian OS, writing it to an SD card, setting up the Raspberry Pi by expanding storage and changing time zone/password. It then guides connecting to a LAN, updating the system, downloading and installing Repetier-Server, and accessing it through a web browser to configure and control the 3D printer remotely over the network.

Uploaded by

JederVieira
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Installation of Repetier-Server on a Raspberry Pi

The follow instructions1​ are intended to


assist a Stacker operator with the
installation of Repetier-Server onto a
Raspberry Pi. ​These instructions are
provided only ​ as a guide and they presume
a basic knowledge of both computer hardware and the LINUX operating system. Neither the
Raspberry Pi nor the LINUX operating system are covered by your Stacker warranty. Stacker’s
customer support does not extend to third-party products.

The Raspberry Pi is a low-cost credit card-sized single-board computer developed in


the United Kingdom by the Raspberry Pi Foundation (​https://www.raspberrypi.org/​).
Repetier-Server (​https://www.repetier-server.com/​) is software which enables the
remote operation of your Stacker 3D printer using any web enabled device such as a
smart phone, tablet or desktop computer. Although Repetier-Server is free, we
strongly encourage you to either purchase the Pro version or provide a donation to Repetier.
Find the donation button at the bottom of the download page
https://www.repetier-server.com/download-repetier-server/

Before you begin, you will need:


● Raspberry Pi (preferably the Raspberry Pi
3 Model B)
● Power supply (5v 2Amp)
● 8GB or larger MicroSD card (class 10
recommended).
● Monitor or TV with an HDMI input
● HDMI cable
● Mouse
● Keyboard
● LAN (local area network) with WiFi or Cat5
cable

Please Note: Some users have experienced problems with their Raspberry Pi due to inadequate
power supply, unsupported microSD cards, or incompatible Wi-Fi adapters which are not plug

1
​ ast Updated 24 October 2016. If you have any suggestions to help improve these instructions, please let us know
L
at ​info@stacker3d.com​.
and play. There are many Raspberry Pi kits and accessories on the market. Make sure to do
your own research and read reviews before purchasing a Raspberry Pi and its accessories.

Step 1: Install Raspbian onto your microSD card


1. Download the latest Raspbian image file to your computer:
http://downloads.raspberrypi.org/raspbian_latest
2. After downloading the .zip file, unzip the file to get the image file (.img).
3. To write the image to your microSD card, follow the instruction found on
https://www.raspberrypi.org/documentation/installation/installing-images/README.md
​ a. For Windows users, you will need to download Win32DiskImager
b. With Win32DiskImager software, write the Raspbian image to the microSD card
(always double check and make sure you select the correct drive when writing an
image file!)

Step 2: Setup the Raspberry Pi


1. Now that the image is written to the microSD card, insert the card into the Raspberry Pi
and connect a keyboard, mouse, and monitor.
2. Connect the power supply, which will boot your Raspberry Pi (note the red and green
lights).
3. Open the terminal and type the command s ​ udo raspi-config​.

4. Within the Configuration Tool


a. Select ​1. Expand Filesystem​ – to use all the free space on the SD card
b. Select ​2. Change User Password​ – Change your password (recommended)
c. Select ​5. Internationalisation Options → ​ ​I​2 Change time zone​ – Change the
timezone to suit your location.
5. Press ​Finish ​to save the configuration and reboot

Step 3: Join Your LAN


1. The Raspberry Pi 3 Model B comes with an internal 8 ​ 02.11n Wireless adapter. To utilize
WiFi on older Raspberry Pi models, you will need to acquire a wireless adapter. You
can always also use a Cat5 cable to connect to the Pi to the LAN.
2. Upon restarting your Raspberry Pi, if the GUI doesn’t load automatically, enter your
username and password. Note, the default username is ​pi ​and the default password is
raspberry​, and manually start the GUI by typing the terminal command s ​ tartx
3. Once the GUI has loaded, click on network icon (top right) and select your network and
enter the network password
4. Open the Terminal and type ​sudo ifconfig​ command to discover your IP address. You
will find your Raspberry Pi’s IP address in the wlan0 section. Red boxes in the image
below show where you should look for your Pi’s IP address.

Step 4: Update the Pi


1. Now that your Raspberry Pi is working and connected to the network, you have the
option of remotely accessing your Pi via SSH. The procedure varies according to your
operating system and personal preference, to see the instructions for connecting with
SSH, go to https://www.raspberrypi.org/documentation/remote-access/ssh/
2. Update the Raspberry Pi by typing each of the following commands into the Terminal
(note, some of these updates will take a considerable amount of time depending upon
your internet download speed):
a. sudo apt-get update
b. sudo apt-get upgrade
c. sudo rpi-update
3. After you have performed all the necessary updates, reboot your Pi with the terminal
command ​sudo reboot

Step 5: Download and Install Repetier Server


1. Open the terminal
​ get
2. Download Repetier Server with the following command: w
http://download.repetier.com/files/server/debian-armel/Repetier-Server-0.80.0-Linu
x.deb
​ udo dpkg -i Repetier-Server-0.80.0-Linux.deb
3. Install the .deb file with the command s

Step 6: Access Repetier


1. Connect your Raspberry Pi via USB cable to your Stacker printer, and then power on
both the Raspberry Pi and the printer.
2. With any web browser on the same network, enter the Raspberry Pi’s IP address with
port extension 3344. For example, if the Raspberry Pi’s IP address was 192.168.0.104,
you would type ​http://192.168.0.104:3344​ into the web browser on your computer or
phone. If you are unable to connect, confirm the IP address of your Raspberry Pi with
either a Terminal ​ifconfig c​ ommand.
3. The first time you access your Stacker printer, you will see the Dashboard, and you will
need to click ​+ Add new Printer​ and complete the configuration items.

4. When adding a printer, you will be directed through the following steps:

Step 1: Naming. ​ Give your printer a name. If you anticipate using multiple 3D printers
on your network, you will want to use unique descriptive names for your printers.

Step 2: Connecting Printer.​ You will need to change the baud rate to 250000. The
other default settings should be correct
Step 3: Geometry.​ The Geometry should match that of your printer, so only make
changes if necessary.

Step 4: Extruders and Bed.​ Verify the number of exturders and change the filament
diameter to 1.75mm.

Step 5: Features.​ The features should match those of your printer, i.e.,
Fan = Yes, SD Card = Yes, and Software Power = No

5. Click ​Finish
6. From the dashboard, select your printer and start using Repetier-Server.
7. For detailed documentation on using Repetier-Server, please visit
https://www.repetier-server.com/documentation/

You might also like