300-101 V23.75

IT Certification Guaranteed, The Easy Way!
Exam : 300-101
Title : Implementing Cisco IP Routing
Vendor : Cisco
Version : V23.75
1
NO.1 Which two options are benefits of BGP peer groups?(Choose two)
A. A configuration change can be applied simultaneously to all peers in the peer group
B. They can optimize backdoor routes
C. They can be updated via multicast
D. Each neighbor in a peer group can have different inbound BGP policies
E. They use soft updates to minimize bandwidth consumption
F. They support groups of paths
Answer: A D
NO.2 Where must a network engineer configure the ip helper-address command on a router?
A. On the interface that will receive the broadcast
B. On the interface that is closest to the destination DHCP server
C. On the global configuration mode
D. On the DHCP configuration
Answer: A
NO.3 Which adverse circumstance can the TTL feature prevent?

A. routing loops
B. DoS attacks
C. link saturation
D. CAM table overload
Answer: B
Explanation
https://www.cisco.com/c/en/us/about/security-center/protecting-border-gatewayprotocol.html
NO.4 Which of the following situations results in a routing loop

A. when you implement noncontiguous IP routing blocks
B. when you have a single point of redistribution
C. when you have multiple points of redistribution
D. when you use NAT translation on the edge of your network
E. when you implement contiguous IP routing blocks
Answer: C
NO.5 Which type of address does OSPFv3 uses to form neighbor adjancises and to send LSAs?
A. unicast addresses
B. tank-local addresses
2
C. unicast IPv4 addresses

D. unicast address FF02 5
Answer: A
NO.6 A network engineer configures two connected routers to run OSPF in Area 0, however, the
routes fail establish adjacency. Which configuration item causes this issue?
A. OSPF process numbers do not match on both neighbor routers
B. The same OSPF router IDs are configured on both routers
C. The same MTU sizes are configured on both sides
D. Area numbers match
Answer: D
NO.7 What is the maximum number of hops on a route that RIPng advertises as reachable?
A. 15
B. 30
C. 99
D. 255
Answer: A
Explanation
https://quizlet.com/166800413/ccnp-ripng-flash-cards/
NO.8
Answer:
check below explanation for details
Explanation
Below is detail answer given
3
4
NO.9 Which feature can mitigate fragmentation issues within network segments that are between
GRE endpoints?
A. TCP Flow Control
B. ICMP DF bit
C. TCP MSS
D. PMTU
Answer: D
NO.10 Which two features were added in MSCHAP version 2?(choose 2)

A. Mutual authentication between peers.
B. Using the MD5 hash for stronger security
C. Using three-way handshakes for authentication.
D. Ability to change an expired password
E. Backward-compatibility with MSCHAP version 1.
Answer: A D
5
NO.11 50. Which SNMP verification command shows the encryption and authentication protocols
that are used in SNMPv37
A. show snmp vi
B. show snmp user
C. show snmp group
D. show snmp
Answer: B
NO.12 Which location within the network is preferred when using a dedicated router for Cisco IP SLA
operations?
A. user edge
B. provider edge
C. access edge
D. distribution edge
Answer: D
NO.13 Refer to the exhibit.

R1 and R2 are unable to establish an EIGRP adjacency. Which action corrects the problem?
A. Change the EIGRP router-id value on one of the routers so that the values on the two routers are
different.
B. Add the no auto-summary command to the R2 configuration so that it matches the Rl
configuration.
C. Change the autonomous system number on one of the routers so that each router has different
values.
D. Chang the IP address and subnet mask on R2 so that it is on the same subnet as R1.
Answer: D
NO.14 Which two statements about PPPOE packet types are true? (Choose two)
A. PADI is an initialization packet sent as a broadcast message
B. PADO is a unicast reply packet sent to the client.
C. PADR is a broadcast packet sent from the client to request a new server.
D. PADR is a broadcast reply packet sent to the client.
E. PADR is a unicast confirmation packet sent to the client.
Answer: A C
NO.15 How big is the smallest packet that will always be fragmented on a standard Ethernet
network with default configuration?
A. 1500 bytes
B. 1800 bytes
C. 2048 bytes
D. 2100bytes
Answer: A
6
NO.16 Which two statements about GRE tunnel interfaces are true? (Choose two)
A. To establish a tunnel the source interface must be m the up/up state.
B. To establish a tunnel the source interface must be a Joopback.
C. A tunnel destination must be a physical interface that is the up state.
D. A tunnel destination must be routable but can be unreachable.
E. A tunnel can be established when the source interface is in the up/down state.
Answer: C D
NO.17 Which three causes of unicast flooding are true/ (Choose three)
A. excess space in the forwarding table
B. changes in the STP topology
C. consistent STP topology
D. asymmetric routing
E. symmetric routing
F. forwarding table overflow
Answer: B D F
NO.18 Which functions are included in the two-message rapid exchanged that a DHCPV6 can receive
from a server?
A. advertise and request
B. solicit and reply
C. solicit and request
D. advertise and reply
Answer: B
NO.19 Refer to the exhibit. Which networking challenge is the most important issue to address to
enable optimal communication between the networks at Company A and Company B?
A. IPv4 MTU
B. IPv4 fragmentation
C. UDP latency
D. unicast flooding
E. asymmetric routing
Answer: E
NO.20 What percent of R1 interfaces bandwidth is ERIGRP allowed to use?

A. 10
B. 20
C. 30
D. 40
Answer: B
NO.21 Which STP feature can reduce TCNs on ports that are connected to end devices?
A. BPDU guard
7
B. Root guard
C. PortFast
D. BackboneFast
Answer: C
NO.22 You want to configure a device to select an OSPF-learned route as the preferred path overan
EBGP-learned route Which action must you take?
A. Increase the OSPF cost
B. Decrease the OSPF cost
C. Increase the oSPF administrative distance
D. Decrease the OsPF administrative distance
Answer: D
NO.23 Which two statements about NTP operation are true? (Choose two.)
A. By default, NTP communications use UDP port 123.
B. If multiple NTP servers are configured, the one with the lowest stratum is preferred.
C. "Stratum" refers to the number of hops between the NTP client and the NTP server.
D. Locally configured time overrides time received from an NTP server.
E. If multiple NTP servers are configured, the one with the highest stratum is preferred.
Answer: A B
NO.24 After reviewing to EVN configuration, a network administrator notices that a predefined BVN,
which is known as" vnet global" was configured. What is the purpose of this EVM?
A. It defines the routing scope fr each particular EVN edge interface.
B. It aggregates and canes all dop1q tagged traffic.
C. It refer to the global routing context and corresponds to the default RIB.
D. It safeguard the virtual network that is preconfigured to avoid mismatched routing instances.
Answer: C
NO.25 Which security feature can protect DMVPN tunnels?

A. IPsec
B. TACACS+
C. RTBH
D. RADIUS
Answer: A

Which statements describes the effect of this configuration on a Cisoc router?
8
A. The default router through 10.0.1 is never used.

B. The default router through 192.168.0.1 is used only when 10.0.0 is unreachable.
C. The default router through 10.0.0.1 only when 192.168.0.1 is unreachable.
D. The default router through 192.168.0.1 is never used.
Answer: B
NO.27 A network engineer has configured an IOS router to synchronize its clock with a Windows
server. After several minutes, the network engineer notices that the local time on the router does not
match the time on the Windows server What is the reason for this?
A. Either a firewall between the two devices or an ACL on the router is blocking TCP port 958
B. Either a firewall between the two devices or an ACL on the router is blocking UDP port 958
C. Either a firewall between the two devices or an ACL on the router is blocking UDP port 123
D. Either a firewall between the two devices or an ACL on the router is blocking TCP port 123
Answer: C
NO.28 In which scenario can asymmetric routing occur?

A. active/standby firewall setup
B. active/active firewall setup
C. redundant routers running VRRP
D. single path in and out of the network
Answer: B
NO.29 Which feature or technology is supported with stateful NAT64?

A. FTP and ICMP on an application layer gateway
B. VFR
C. IP multicast
D. NAT44 and NAT64 on the same interface
Answer: B
NO.30 Drag and drop the IPv6 NAT characteristic from the left onto the correct IPv6 NAT category on
the right.
9
Answer:
Explanation
NO.31 Other than a working EIGRP configuration which component must be the same on all routers
for EIGRP authentication key rollover to work correctly?
A. time
B. SNMP
C. passwords
D. SMTP
Answer: A
NO.32 Which two options are benefits of BGP peer groups?( Choose two)
A. They can optimize backdoor routes
B. They support groups of paths
10
C. A configuration change can be applied simultaneously to all peers in the peer group
D. Each neighbor in a peer group can have different inbound BGP policies
E. They can be updated via multicast
F. They use soft updates to minimize bandwidth consumption
Answer: C D
NO.33 Refer to the exhibit an engineer is enabling VPN services foe a customer and noticed the
output when placing the customer facing interfaces into a VRF which action connects the issue?
A. Reset interface Gigabite Ethernet 1.
B. Disable the VRF CUST_A
C. REconfigure the IP address on Gigabite Ethernet 1.
D. Enabling IPv6 on the interface
Answer: C
NO.34 A Network engineer recently deployed easy virtual networking in the enterprise network.
Which feature improves shared services support?
A. router replication
B. tunnel feedback
C. routers distinguishers
D. edge interfacing
Answer: A
NO.35 Which two effects of symmetric routing are true? (Choose two)
A. unicast flooding
B. uRPF failure
C. errdisabling of ports
D. port security violations
E. excessive STP reconvergence
Answer: A B
NO.36 JS Industries has expanded their business with the addition of their first remote office. The
remote office router (R3) was previously configured and all Corporate subnets were reachable from
R3. JS Industries is interested in using route summarization along with the EIGRP Stub Routing feature
to increase network stability while reducing the memory usage and bandwidth utilization to R3.
Another network professional was tasked with implementing this solution. However, in the process
of configuring EIGRP stub routing connectivity with the remote network devices off of R3 has been
lost.
Currently EIGRP is configured on all routers R2, R3, and R4 in the network. Your task is to identify and
resolve the cause of connectivity failure with the remote office router R3. Once the issue has been
resolved you should complete the task by configuring route summarization only to the remote office
router R3.
You have corrected the fault when pings from R2 to the R3 LAN interface are successful, and the R3 IP
routing table only contains 2 10.0.0.0 subnets.
11
12
Answer:
See the explanation part for details.
13
Explanation
First we have to figure out why R3 and R4 can not communicate with each other. Use the show
running-config command on router R3.
[eigrp10.jpg]
Notice that R3 is configured as a stub receive-only router. The receive-only keyword will restrict the
router from sharing any of its routes with any other router in that EIGRP autonomous system. This
keyword will also prevent any type of route from being sent. Therefore we will remove this command
and replace it with the eigrp stub command:
R3# configure terminal R3(config)# router eigrp 123 R3(config-router)# no eigrp stub receive-only
R3(config-router)# eigrp stub R3(config-router)# end Now R3 will send updates containing its
connected and summary routes to other routers. Notice that the eigrp stub command equals to the
eigrp stub connected summary because the connected and summary options are enabled by default.
Next we will configure router R3 so that it has only 2 subnets of 10.0.0.0 network. Use the show ip
route command on R3 to view its routing table:
[ee1%255B5%255D.jpg]
14
Because we want the routing table of R3 only have 2 subnets so we have to summary sub-networks
at the interface which is connected with R3, the s0/0 interface of R4.
There is one interesting thing about the output of the show ip route shown above: the 10.2.3.0/24,
which is a directly connected network of R3. We can't get rid of it in the routing table no matter what
technique we use to summary the networks. Therefore, to make the routing table of R3 has only 2
subnets we have to summary other subnets into one subnet.
In the output if we don't see the summary line (like 10.0.0.0/8 is a summary...) then we should use
the command ip summary-address eigrp 123 10.2.0.0 255.255.0.0 so that all the ping can work well.
In conclusion, we will use the ip summary-address eigrp 123 10.2.0.0 255.255.0.0 at the interface
s0/0 of R4 to summary.
R4> enable R4# conf t
R4(config)# interface s0/0 R4(config-if)# ip summary-address eigrp 123 10.2.0.0 255.255.0.0 Now we
jump back to R3 and use the show ip route command to verify the effect, the output is shown below:
[ee2%255B5%255D.jpg]
15
Note: Please notice that the IP addresses and the subnet masks in your real exam might be different
so you might use different ones to solve this question.
Just for your information, notice that if you use another network than 10.0.0.0/8 to summary, for
example, if you use the command ip summary-address eigrp 123 10.2.0.0 255.255.0.0 you will leave a
/16 network in the output of the show ip route command.
[ee3%255B5%255D.jpg]
But in your real exam, if you don't see the line "10.0.0.0/8 is a summary, Null0" then you can
summarize using the network 10.2.0.0/16. This summarization is better because all the pings can
work well.
Finally don't forget to use the copy run start command on routers R3 and R4 to save the
configurations.
R3(config-if)# end
R3# copy run start
R4(config-if)# end
R4# copy run start
If the "copy run start" command doesn't work then use "write memory".
16
NO.37
Answer:
Check the explanation part below:
Explanation
Always remember the Process id and area , in this question process id is 37a nd OSPF area is 23
Process id 37 area 23 Indianapoll at first go to HOST A and write this configuration
Seattle(config)#router ospf 37 Seattle (config-router)#network 192.168.3.4 0.0.0.3 area 23 Seattle
(config-router)#area 23 stub For Host B Indianapoll #configure terminal Indianapoll (config)#router
ospf 37 Indianapoll (config-router)#network 192.168.3.4 0.0.0.3 area 23 Indianapoll (config-
router)#area 23 stub no-summary
17
Show ip route in host A

To verify the lab O* this one should be there.
NO.38 Which two statements about NAT in a DMVPN environment are true?(choose two)
A. A hub router can be behind a dynamic NAT on a device.
B. Spoke routers can reside only on the public side of a NAT device.
C. Two spokes can establish session among themselves using PAT behind different devices.
D. A spoke router can be represented by a static NAT on a device.
E. A hub router can use static NAT for its public IP address.
Answer: D E
NO.39 Which three methods can a network engineer used to fix a metric-based routing loop in the
network?(choose three)
18
A. Filter routes manually using prefix lists

B. Implement proper network summarization on key routing points
C. Utilize route database filters
D. Filter routes based on tags
E. Implement offset lists at network boundaries
F. Filter routes manually using distribute lists
Answer: D E F
NO.40 A network engineer executes the command show ip eigrp vrf purple topology Which type of
information is displayed as a result?
A. route successors for a specific routing table
B. active neighbors for a global routing table
C. routes for a global routing table
D. updates that were sent for a specific routing table
Answer: D
NO.41 Which statement about spilt-horizon rule for distance vector routing protocols are true?
A. A router advertises a route to an unreachable network with an infinite metric.
B. A router does not advertise routes to any neighboring router.
C. A router advertises routes back out the interface on which it learned them with an mfirrte metric.
D. A router does not advertise routes back out the interface on which it learned them.
Answer: A
NO.42 Which two statements about Frame Relay point-point connections are true?
A. They can operate normally without a DLCI map.
B. The device can establish a pout to-point connection to the cloud without a DLCI.
C. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud.
D. Changing a point-to-port subinterface to a different type requires the device to be reloaded.
E. Each physical interface that extends to the Frame Relay cloud can support a SVC.
Answer: C D
NO.43 What type of route filtering is occurring on R6?

A. Distribute-list using an ACL
B. Distribute-list using a prefix-list
C. Distribute-list using a route-map
D. An ACL using a distance or 255
Answer: A
19
You have correctly identified the inside and outside interfaces in the NAT configuration of this device.
Which effect of the configuration is true?
A. static NAT
B. dynamic NAT
C. PAT
D. NAT64
Answer: C
Which statement describes the effect of this configuration on a Cisco router'?

A. The default route through 10 0 0 1 is never used
B. The default route through 192 168 0 1 is used only when 10 0 0 1 is unreachable
C. The default route through 192 168 0.1 is never used
D. The default route through 10 0 0 1 is used only when 192 168 0 1 is unreachable
Answer: D
NO.46 Considering the IPv6 address independence requirement, which process do you avoid when
you use NPTw for translation?
A. IPsec AH header modification
B. checksum verification
C. IPv6 duplication and conservation
D. Rewriting of higher layer information
Answer: D
NO.47 Which statement about conditional debugging is true?
20
A. It can support only one condition at a time

B. You can limit the output to a specific interface
C. It generates debug messages only for packets entering the router
D. It is limited to Ethernet, serial, and multilink interfaces
Answer: B
NO.48 Which type of information is displayed when a network engineer executes the show track 1
command on the router?
A. information about tracking list 1 information about the IP route track table
B. time to next poll for track object 1
C. tracking information statistics
Answer: A
NO.49 Which two statements about EVN are true? (Choose two.)
A. It supports IPv6 traffic.
B. It can support up to 16 VNs.
C. It uses redistribution to share routes between VNs.
D. It supports SSM only.
E. A configuration can be based on an existing VRF configuration.
Answer: C E
Explanation
https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/layer-3-
vpnsl3vpn/whitepaper_c11-638769
NO.50 Which three algorithms can you configure with the ip cef load-sharing algorithm
command?(choose three)
A. per-packed
B. Tunnel
C. per-destination
D. Universal
21
E. Per-source
F. Include-port
Answer: B D F
NO.51 Which two statements about uRPF are true? (Choose two)
A. It is enabled on a per-mterface basis CD It is enabled globally
B. Strict mode is most appropriate for networks with asymmetnc routing
C. Strict mode may drop legitimate traffic
D. The keyword any can be used with both strict mode and loose mode
E. Loose mode may drop traffic when asymmetric routing occurs on the network
Answer: A D
NO.52 Drag and drop the statement about device security from the left on the correct features on
the right.
Answer:
22
NO.53 Which two statements about AAA with the local database are true?(Choose two)
A. The local database can serve only as a backup authentication method
B. It supports a limited number of usemames and passwords Accounting is not supported locally
C. By default, it is queried before a TACACS+ or RADIUS server
D. Authorization is available only for one-time -use logins
Answer: B C
NO.54 A Network engineer wants a NTP Client to be able to update the local system without
updating or synchronizing with the remote system. Which keyboard for the ntp access-grup
command is needed to accomplish this?
A. server
23
B. peer
C. query-only
D. server-only
Answer: A
NO.55 Which problem can be caused by latency on a UDP stream?

A. The devices at each end of the stream are forced to negotiate a smaller vwndow size.
B. The device that receives the stream is forced to hold data m the buffer for a longer penod of time.
C. The device that sends the stream is forced to hold data in the buffer for a longer period of time.
D. The overall throughput of the stream is decreased.
Answer: B
NO.56 What happens when two EIGRP peers have mismatched K values?
A. The two devices are unable to correctly perform equal-cost routing
B. The two devices fail to perform EIGRP graceful shutdown when one device goes down
C. The two devices fail to from an adjacency
D. The two devices are unable to correctly perform unequal-cast load balancing
Answer: C
Explanation
http://www.ciscopress.com/articles/article.asp?p=27839
https://supportforums.cisco.com/t5/lan-switching-and-routing/eigrp-k-value-mismatchissue/td-
p/1008233
NO.57 Which two causes of latency are true?(choose two)

A. High bandwidth on a link
B. Split horizon
C. Propagation delay
D. Serialization delay
E. Under-utilization of a link
Answer: C E
NO.58 Drag and drop the GRE features from the left onto the correct descriptions on the right.
24
Answer:
NO.59 Which key chain is being used for authentication of EIGRP adjacency between R4 and R2?
A. CISCO
B. EGRP
C. KEY
D. MDS
25
Answer: A
Router DHCP is configured to lease IPv4 and IPv6 addresses to clients on ALS1 and ALS2. Clients on
ALS2 receive IPv4 and IPv6 addresses Clients on ALS1 receive IPv4 addresses. Which configuration on
DSW1 allows clients on ALS1 to receive IPv6 addresses'?
A. DSW1(cunfig-if)>>ipv6 dhcp relay destination 2002:404:404::404:404 GigabitEthernet1/2
B. DSW1(configFipv6 route 2002:404:404: 404:404/128 FastEthemet1/0
C. DSWKconfKj K)cipv6 helper address 2002:404:404:404:404
D. DSW1 uihrp-condg^default-router 2002:A04:A01:A04:A01
Answer: D
NO.61 Which command instructs a PPPoE client to obtain its IP address from the PPPoE server?
A. IP address negotiated
B. IP address DHCP
C. IP address dynamic
D. IP address auto negotiate
Answer: A
NO.62 Which two commands must be configured on a DMVPN hub to enable phase 3? (Choose two
)
A. ip nhrp redirect
B. ip nhrp interest
C. ip nhrp shortcut
D. Ip nhrp map
26
E. ip redirects
Answer: A D
NO.63 You are configuring a Microsoft client to call a PPP server using CHAP. Only the client will be
authenticated.
But the clients password has expired and must be changed. Which ppp server configuration allows
the call be completed?
A. ppp authentication ma-chap-v2
B. ppp authentication ms-cahp-v2 callin
C. ppp authentication chap
D. ppp authentication callin
E. ppp authentication ms-chap callin
Answer: B
NO.64 Which set of actions does a network engineer perform to set the IPv6 address of a DHCP relay
server at the VLAN interface level?
A. Enter the global configuration mode, enable IPv6 DHCP relay from interface confi; mode, and
define the IPv6 address of a DHCP relay server.
B. Enter the global configuration mode and enable the IPv6 DHCP relay
C. Enter the VLAN interface configuration mode, enable IPv6 DHCP relay, and define the IPv6 address
of a DHCP relay server
D. Enter the VLAN interface configuration mode and define the IPv6 address of a DHCP relay server.
Answer: C
How can you configure a second export destination for IP address 192.168.10.1?
A. Specify a different TCP port.
B. Specify a VRF.
C. Configure a version 5 flow-export to the destination
D. Specify a different UDP port.
E. Specify a different flow ID.
Answer: B
NO.66 What is VRF-Lite?

A. VRF without VPN
B. VRF without MPLS
C. VRF wrthout Cisco Express Forwarding swrtching
D. VRF wrthout independent routing tables
27
Answer: C
NO.67 When OSPF is forming an adjacency, in which state does the actual exchange of the
information in the link-state database occur?
A. loading
B. exchange
C. INIT
D. exstart
Answer: B
NO.68 Which access list entry check for an ACK within a packet TCP header?
A. access-list 49 permit tcp any any eq 21 established
B. access-list 49 permit tcp any any eq 21 tcp-ack
C. cess-list 149 permit tcp any any eq 21 established
D. access-list 49 permit ip any any eq 21 tcp-ack
Answer: C
NO.69 Which two features does RADIUS combine?(Choose two)

A. authorization
B. authenticate
C. ssH
D. accounting
E. Telnet
Answer: A B
NO.70 Which statement is true about an edge interface in relation to the Cisco Easy Virtual
Network?
A. An edge interface is used to differentiate VRF instances.
B. An edge interface connects to end devices such as hosts and servers that are VRF-aware.
C. An edge interface connects a user device to the EVN while defining the EVN boundaries.
D. An edge interface is configured using the vnet trunk command under the switched virtual
interface.
Answer: C
NO.71 Which two statements about the enable secret and enable password commands are true?(
Choose two)
A. The both commands are missing from the global configuration, vty lines use the console password
B. The enable secret command overrides enable password
C. The enable password command has a stronger encryption algorithm than enable secret
D. The enable secret command is backwards-compatible with more versions of IOS
E. The enable secret and enable password commands must be used together
Answer: A B
28
Which routes from OSPF process 5 are redistributed into EIGRP?

A. E1 and E2 subnets matching access list TO-OSPF
B. E1 and E2 subnets matching prefix list TO-OSPF
C. only E2 subnets matching access list TO-OSPF
D. only E1 subnets matching prefix listTO-OS1
Answer: D
NO.73 Which Cisco Express Forwarding component maintains the Layer 2 next-hop addresses that
are used for hardware switching?
A. FIB
B. RIB
C. adjacency table
D. ARP table
Answer: C
NO.74 Which command is implemented to display log messages with a timestamp that includes the
length of time since the device was last rebooted?
A. service timestamps log datetime msec
B. logging facility 20
C. service timestamps debugging localtim
D. logging monitor 7
E. service timestamps log uptime
Answer: E
NO.75 A network engineer is enabling conditional debugging and execute two command. Debug
condition interfaces serial00 and debug condition interfaces serial 0/1. Which debugging output is
displayed as a result?
A. interface cannot be used as a debug condition.
B. Output is display for both specified interfaces.
C. Output is display for interface serial 0/1 only.
D. Output is display for interface 0/0 only.
Answer: B
NO.76 Which command sequence is implemented on a router to configure unicast reverse path
29
forwarding in loose mode?

A. interface GigabitEthernet0/0 ip verify unicast source reachable-via rx
B. interface GigabitEthernet0/0 ip unicast source reachable-via loose
C. interface GigabitEthernet0/0 ip verify unicast source reachable-via any
D. interface GigabteEthernet0/0 Ip verify uncast source reachable-via all
Answer: C
NO.77 Which command sequence can you enter on a router to configure Unicast Reverse Path
Forwarding in loose mode?
A. interface GigabitEthernet0/0 ip verify unicast source reachable-via loose
B. interface GigabitEthernet0/0 ip verify unicast source reachable-via all
C. interface GigabitEthernet0/0 ip verify unicast source reachable-via any
D. interface GigabitEthernet0/0 ip verify unicast source reachable-via rx
Answer: C
You want router R1 to perform unequal-cost routing to the 192.168.10.0/24 network. What is the
smallest EIGRP variance value that you can configure on R1 to achieve this result?
A. 1
B. 2
C. 3
D. 4
Answer: A
NO.79 In SNMP v3, which security level provides encryption of the data?
30
A. authNoPriv
B. authMember
C. authPriv
D. noAuthNoPnv
Answer: C
NO.80 13. Which two features are provided by EIGRP for IPv6?(choose two)
A. Backbone areas
B. SPF algorithm
C. Partial updates
D. Area border router
E. Scaling
Answer: C E
NO.81 What is the role of a route distinguisher in a VRF-Lite setup implementation?

A. It extends the IP address to identify which VRF instance it belongs to.
B. It manages the import and export of routes between two or more VRF instances
C. It enables multicast distribution for VRF-Lite setups to enhance EGP routing protocol capabilities
D. It enables multicast distribution for VRF-Lite setups to enhance IGP routing protocol Capabilities
Answer: A
NO.82 Which calculation is used to determine the default EIGRP metric?

A. bandwidth - delay
B. bandwidth / delay
C. bandwidth * delay
D. bandwidth +
Answer: D
NO.83 Which configuration parameter is invalid when configuration unicast reverse path
forwarding?
A. source reachable via both
B. allow self to router
C. allow based on ACL match
D. allow default route
Answer: A
NO.84 You are configuring a static route. Which action must you take to avoid the possibility of
recursive row
A. Use the ip route command to specify the next-hop IP address only
B. Specify the next hop on a directly connected interface
C. Use the ip route command to specify both the next-hop IP address and the connected interface
D. Use the ip route command to specify the connected interface only
Answer: C
31
NO.85 Which two protocols are required for DMVPN? (Choose two)
A. mGRE
B. IPsec
C. OpenVPN
D. PPTP
E. INHRP
Answer: B E
NO.86 Which criterion does the BGP maximum paths feature use for load balancing?
A. MED
B. local preference
C. weight
D. router ID
Answer: C
Explanation
Also MED and local preference should considered.
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_bgp/configuration/xe-16/irgxe-16-
book/ibgp-multipa
https://learningnetwork.cisco.com/docs/DOC-11233
32
NO.87 Which NAT command do you enter to disable dynamic ARP learning on an interface?
A. R1(config-if)#ip nat enable
B. R1(config-if)#ip nat inside
C. R1(config)#ip nat service
D. R1(config-if)#ip nat outside
E. R1(config)#ip nat allow-static-host
Answer: E
NO.88 Which two statements are limitations of stateful NAT64? (Choose two)
A. It supports DNS64 only
B. Layer 4 supports TCP only
C. It is unable to route VRF traffic
D. It is unable to route multicast traffic
E. It supports FTP traffic only with an ALG
Answer: C D
NO.89 Which criterion does BGP evaluate first when determinin the best path?
A. MED value
B. neighbor address
C. local preference value
D. weight
Answer: D
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html
33
NO.90 Drag and drop the statements about NAT64 from the left onto the correct NAT64 types on
the right.
Answer:
Explanation
34
NO.91 Drag and drop the statements about device security from the left onto the correct description
on the right.
Select and Place:
Answer:
35
NO.92 Which password takes precedence if you configure multiple passwords for Telnet connections
to a Cisco IOS device?
A. console line password
B. enable secret password
C. enable password
D. aux line
E. password
Answer: B
36
Which three NTP features can be deduced on the router (Choose three.)
A. only accepts time requests from 192.168.1.1
B. only handle four requests at a time
C. only is in stratum 4
D. only updates its time from 192.168.1.1
E. only accepts time requests from 192.168.1.4
F. only updates its time from 192.168.1.4
Answer: A C F
NO.94 A route with default RIPv2 settings loses connectivity to it's next-hop neighbor. How long
dows the router wait before removing the route to the next hop from its route table?
A. 30 seconds
B. 60 seconds
C. 180 seconds
D. 240 seconds
Answer: D
NO.95 Which condition must be met before two EVN devices can connect?
A. An EtherChannel must be configured with at least two interfaces connected between the devices.
B. A fiber connection must be established between the devices.
C. One VLAN interface must be configured between the devices.
D. A trunk interface must be configured between the devices.
Answer: D
NO.96 You are a network engineer with ROUTE.com, a small IT company. They have recently merged
two organizations and now need to merge their networks as shown in the topology exhibit. One
network is using OSPF as its IGP and the other is using EIGRP as its IGP. R4 has been added to the
existing OSPF network to provide the interconnect between the OSPF and EIGRP networks. Two links
have been added that will provide redundancy.
The network requirements state that you must be able to ping and telnet from loopback 101 on R1 to
the OPSF domain test address of 172.16.1.100. All traffic must use the shortest path that provides the
37
greatest bandwidth. The redundant paths from the OSPF network to the EIGRP network must be
available in case of a link failure. No static or default routing is allowed in either network.
A previous network engineer has started the merger implementation and has successfully assigned
and verified all IP addressing and basic IGP routing. You have been tasked with completing the
implementation and ensuring that the network requirements are met. You may not remove or
change any of the configuration commands currently on any of the routers. You may add new
commands or change default values.
Answer:
Check the Explanation part for details answer.
Explanation
First we need to find out 5 parameters (Bandwidth, Delay, Reliability, Load, MTU) of the s0/0/0
interface (the interface of R2 connected to R4) for redistribution:
R2#show interface s0/0/0
Write down these 5 parameters, notice that we have to divide the Delay by 10 because the metric
unit is in tens of microsecond. For example, we get Bandwidth=1544 Kbit, Delay=20000 us,
Reliability=255, Load=1, MTU=1500 bytes then we would redistribute as follows:
R2#config terminal
R2(config)# router ospf 1
R2(config-router)# redistribute eigrp 100 metric-type 1 subnets
R2(config-router)#exit
R2(config-router)#router eigrp 100
R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500
Note: In fact, these parameters are just used for reference and we can use other parameters with no
problem.
If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000) For R3 we use the
show interface fa0/0 to get 5 parameters too R3#show interface fa0/0 For example we get
Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500 bytes R3#config terminal
R3(config)#router ospf 1 R3(config-router)#redistribute eigrp 100 metric-type 1 subnets
38
R3(config)#exit R3(config-router)#router eigrp 100 R3(config-router)#redistribute ospf 1 metric

10000 100 255 1 1500 Finally you should try to "show ip route" to see the 172.16.100.1 network (the
network behind R4) in the routing table of R1 and make a ping from R1 to this network.
Note: If the link between R2 and R3 is FastEthernet link, we must put the command below under
EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4), which is better than R1
-> R2 -> R4.
R2(config-router)# distance eigrp 90 105
This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP
external routes to 105, which is smaller than the Administrative Distance of OSPF (110) -> the link
between R2 & R3 will be preferred to the serial link between R2 & R4.
Note: The actual OPSF and EIGRP process numbers may change in the actual exam so be sure to use
the actual correct values, but the overall solution is the same.
NO.97 Which OSPF network type uses a DR?

A. Nonbroadcast multi-access
B. point-to-point
C. point-to-multipoint
D. point-to-point nonbroadcast
Answer: A
Explanation
https://learningnetwork.cisco.com/thread/35730
NO.98 Which two options are components of a dual stack? (Choose two.)
A. IPv6 traffic
B. IPv4 traffic
C. Layer 3 switch
D. EIGRP
E. Layer 2 switch
F. OSPF
Answer: A B
NO.99 Which two LSA types were introduced to support OSPF for IPV6?
A. type 9
B. type 7
C. type 8
D. type 10
E. type 5
Answer: A C
NO.100 Drag and drop the statements from the left onto the correct uRPF modes on the right Select
and Place:
39
Answer:
Explanation
40
Based on Cisco best practice, which statement about the output is true?
A. The output should be analyzed by a network engineer before executing any debug commands on
an IOS router in production
B. The output should be analyzed by a network engineer before executing any configuration
commands on an IOS router in production
C. The output should be analyzed by a network engineer before allocating additional memory and
CPU usage to processes on an IOS router in production
D. The output should be analyzed by a network engineer before executing other show commands on
an IOS router in production
Answer: A
After configuring GRE between two routers running EIGRP that are connected to each other via a
WAN link, a network engineer notices that the two routers cannot establish the GRE tunnel to begin
the exchange of routing updates What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking TCP 47.
41
B. Either a firewall between the two routers or an ACL on the router is blocking IP protocol
C. Either a firewall between the two routers or an ACL on the router is blocking UDP 57
D. Either a firewall between the two routers or an ACL on the router is blocking IP protocol number
47
Answer: B
NO.103 A customer asks its service provider for VPN support for IPv4 and IPv6 address families
Which command enables a VRF that supports these requirements?
A. Router(config-vrf) #route-target 004:006
B. Router(config-vrf)#rd 004: 006
C. Router(config)#ipvrf CUSTOMER
D. Router(config-vrf)#vrf definition
CUSTOMER
Answer: D
NO.104 Which statement about stateless and stateful IPv6 auto configuration is true?
A. Both stateless and stateful autoconfiguration require no additional setup
B. Stateless autoconfiguration requires additional setup, whereas stateful autoconfiguration requires
no additional setup
C. Stateless autoconfiguration requires no additional setup, whereas stateful autoconfiguration
requires additional setup
D. Both stateless and stateful autoconfiguration require additional setup
Answer: D
NO.105 What is the minimum privilege level to allow a user to execute all user-level commands but
prohibits enable level commands by default?
A. level 0
B. level 1
C. level 14
D. level 15
E. level 16
Answer: B
NO.106 Which task must you perform to enable point-to-point frame relay connection?
A. Disable inverse ARP
B. Configure the encapsulation type
C. Enable inverse ARP
D. Configure static address mapping
Answer: D
NO.107 Drag and drop the statement from the left onto the correct IPv6 router security features on
the right.
42
Answer:
43
NO.108 A network engineer wants to monitor hop-by-hop response time on the network Which IP
SLA operation accomplishes this task?
A. UDP echo
B. ICMPecho
C. ICMP path echo
D. ICMP path jitter
Answer: C
NO.109 When an EIGRP router discovers a new neighbor, which packet type does the router send to
help the neighbor build its topology table?
A. replies
B. requests
C. updates
D. queries
Answer: C
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routingprotocol-
eigrp/13669-1.html#p
NO.110 Which protocol does VRF-Lite support?

A. IS-IS
B. ODR
C. EIGRP
D. IGRP
Answer: C
NO.111 Which adverse event can occur as a consequence of asymmetric routing on the network?
A. vulnerability to a man-in the - middle attack
B. inadvertent HSRP active router preemption
C. errdisabled port
D. unicast flooding
Answer: D
NO.112 Which technology supports overlapping IP addresses on a single interface?

A. policy-based routing
B. VRF-Lite
C. On-Demand Routing
44
D. QoS
Answer: B
NO.113 Which option is an invalid redistribute command option for redistributing routes from
EIGRPintoOSPF?
A. route map
B. tag
C. access list
D. metric
Answer: C
NO.114 Which command creates a manual summary on an interface when using EIGRP?
A. ip summary-address 100 172.32.0.0 255.255 254.0
B. ip summary-address eigrp 100 172.32.0.0 255.255.254.0
C. summary-address eigrp 100 172.32.0.0 255.255.254.0
D. area 100 range 172.32.0.0 255.255.254.0
Answer: B
NO.115 Refer to the exhibit. Which effect of this configuration is true?
A. It designates the interface as a GRE tunnel endpoint

B. it configures 802 lq trunking on the interface
C. I designates the interface as an EVN trunk
D. I removes VTP from the interface
Answer: B
NO.116 During which DMVPN phase is spoke to-spoke communication enabled?

A. Phase 4
B. Phase 1
C. Phase 2
D. Phase 5
Answer: C
NO.117 Drag and Drop the Frame Relay LMI extensions from the left onto the correct descriptions
on the right.
45
Answer:
Explanation
+ Address registration - allows neighboring Cisco devices to exchange the management ip addresses
+ Global addressing - Enables Frame Relay to identify interfaces in same manner as LAN
+ Multicasting - Provides most efficient transmission of routing protocol messages and support
address resolution
+ Simple flow control - Supports devices that are unable to use congestion notification
+ Virtual circuit - Prevents data from being transmitted in black hole
NO.118 Which LSA type in 0SPFv3 is used for link-local u

A. Link LSA type 5
B. Link LSA type 8
C. Link LSA type 6
D. Link LSA type 4
Answer: B
NO.119 Users were moved from the local DHCP server to the remote corporate DHCP server. After
46
the move, none of the users were able to use the network. Which two issues will prevent this setup
from working properly?
(Choose two)
A. The broadcast domain is too large for proper DHCP propagation
B. The DHCP server IP address configuration is missing locally
C. The route to the new DHCP server is missing
D. Auto-QoS is blocking DHCP traffic.
E. 802.tX is blocking DHCP traffic
Answer: B C
NO.120 A network engineer has configured an IOS router to synchronize its clock with a Windows
server. After several minutes, the network engineer notices that the local time on the router does not
match the time on the windows server. What is the reason for this?
A. Ether a firewall between the drives or an ACL on the router is blocking TCP port 958.
B. Either a firewall between the two devices or an ACL on the router is blocking TCP port 123.
C. Either a firewall between the two devices or an ACL on the router is blocking UDP port 123.
D. Either a firewall between the two devices or an ACL on the router is blocking UDP port 858.
Answer: C
NO.121 Which condition prevents the establishment of a DMPVN tunnel between two spokes?
A. The two spokes have different tunnel keepalive settings
B. HSRP is enabled on the spoke devices
C. IPsec is enabled on the spoke devices
D. The two spokes are behind different PAT devices
Answer: A
NO.122 If you convert a WAN connection with OSPF from form T1 to a frame Relay circuit which two
actions must you take to enable the connection?(Choose two.)
A. Change the OSPF network type to nonbroadcast
B. Change the OSPF network type to multipoint nonbroadcast
C. Manually configure the hello and dead timers Change the OSPF network type to broadcast
D. Manually configure neighbors in the OSPF process
Answer: A D
NO.123 Which two statements about NetFlow templates are true? (Choose two.)
A. Only NetFlow version 9 is template based.
B. NetFlow version 5 and version 9 are template based.
C. Only NetFlow version 5 is template based.
D. Template can increased bandwidth usage.
E. They can increase overall performance.
F. They can reduce bandwidth usage.
Answer: A D
47
NO.124 45. Refer to the following configuration command. Which statement about the command is
true?
router(config)ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
A. Any packet that is received in the inside interface with a source IP port address 172.16.10.8:8080
is translated to 172.16.10.8:80
B. Any packet that is received in the inside interface with a source IP port address of 172.16. 10.8: 80
is translated to 172.16.10.8.8080
C. The router accepts only a TCP connection from port 8080 and port 80 on IP address 172.16
D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8 is
redirected to port 8080 or port 80
Answer: A
NO.125 Which feature filters information at the interface level?

A. prefix-list
B. syslog
C. conditional debugging
D. local logging
Answer: D
NO.126 Refer to the exhibit. How does R1 handle the route to network 10.1.80.0/24?
A. R1 redistributes network 10.1.80.0/24 into EIGRP without changing the mask

B. R1 changes the mask to /32 and then redistributes network 10.1.80.0/24 into EIGRP as a classful
network
C. R1 changes the mask to /32 and then redistributes network 10.1.80.0/24 into EIGRP as a assless
network
D. R1 fails to redistribute network 10.1.80.0/24 into EIGRP
Answer: A
48
What is indicated by the show ip cef command for an address?

A. CEF cannot switch packet for this route and drops it
B. CEF is unable to get routing information for this route
C. CEF cannot switch packet for this route and passes it to the next best switching method
D. A valid entry and is punted to hardware-based forwarding
Answer: C
NO.128 Which two EIGRP metrics have nonzero K values by default? (Choose two.)
A. reliability
B. delay
C. cost
D. load
E. bandwidth
Answer: B E
NO.129 Which two debug commands can you use to view issues with CHAP and PAP authentication?
(Choose two.)
A. DebugTACACS
B. Debug radius
C. Debug AAA authentication
D. Debug PPP negotiation
E. Debug PPPauthentication
Answer: D E
49
You are configuring the R1 Serial0 interface for a point-to-point connection. Drag and drop the
required configuration statements from the left onto the correct locations from the diagram on the
right Not all commands are used.
50
Answer:
Explanation
NO.131 Which statement about dynamic NAT is true?

A. It maps inside addresses to different port numbers.
B. It creates a one-to-one mapping of inside addresses to a global address.
51
C. It uses the overload command to map addresses.

D. It maps inside addresses to a pool of global addresses.
Answer: D
NO.132 What is the administrative distance of an EIGRP summary route?

A. 90
B. 5
C. 1
D. 170
Answer: B
NO.133 Which command must you configure globally to supportRIPng?

A. ip routing
B. ip cef
C. ipv6 enable
D. ipv6 unicast-routing
Answer: D
NO.134 Which statement describes the effect of this configuration on a Cisco router?
A. The default router through 192.168.0.1 is used only when 10.0.0.1 is unreachable
B. The default router through 192.168.0.1 is never used.
C. The default through 10.0.0.1 used only when 192.168.0.1 is unreachable.
D. The default route through 10.0.0.1 is never used.
Answer: A
NO.135 Which two statements about the OSPF down bit are true? (Choose two)
A. It is set only for LSA types 3,5. and 7
B. It is set only for LSA types 1, 2 and 4
C. It is set only when an OSPF virtual link is created
D. It is set when MP-BGP routes are redistributed into OSPF
E. It is set when OSPF routes are redistributed into BGP
Answer: A D
NO.136 Which IP SLA operation can be used to simulate voice traffic on a network?
A. TCP connect
B. UDP-jitter
C. ICMP-echo
D. ICMP-jitter
Answer: B
NO.137 Which two types of traffic can benefit from LLQ? (Choose two)
A. voice
B. telnet
52
C. video
D. file transfer
E. email
Answer: A C
NO.138 When a new PC is connected to the network, which step must it take first to receive a DHCP
address?
A. It sends a DHCPHELLO message to the DHCP server IP address.
B. It sends a DHCPREQUEST message to the DHCP server IP address.
C. It sends a DHCPREQUEST message to 255.255.255.255.
D. It sends a DHCPDISCOVER message to 255.255.255.255.
Answer: D
NO.139 Which action is the most efficient way to handle route feedback when connecting a RIPv2
network to OSPF?
A. Implement distribute lists
B. Implement route tags
C. Implement route maps with access lists
D. Implement IP prefix lists.
Answer: C
NO.140 Company is deploying a multicast application that must be accessible between sites, but
must not be accessible outside of the organization Based on
A. FF00:/16
B. FFOE:/16
C. FF02:/16
D. FF08:/16
Answer: C
NO.141 Which two packet type can an EIGRP router send when a route goes into the Active
state?(choose two)
A. reply
B. request
C. hello
D. update
E. query
Answer: A E
Explanation
https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-
routingprotocoleigrp/13669-1.html#p
53

Which networking challenge is the most important issue due to address to enable optimal
communication between the networks at company A and company B?
A. unicast flooding
B. IPv4 MTU
C. asymmetric
D. routing IPv4 fragmentation
E. UDP latency
Answer: C
54
Which option describes why the EIGRP neighbors of this router are not learning routes that are
received from OSPF?
A. The routing protocols do not have the same AS number.
B. There is no overlap in the subnets advertised.
C. The subnet defined in OSPF is not part of area 0.
D. Default metrics are not configured under EIGRP.
Answer: D
NO.144 Where can NetFlow export data for long term storage and analysis?
A. another network device
B. syslog
C. flat file
D. collector
Answer: D
NO.145 Which two statements about the OSPF down bit are true? (Choose two )
A. It is set when OSPF routers are redistributed into BGP
B. It is set only for LSA types 1,2 and 4.
C. It set when an OSFP virtual link in created.
D. It is set only for LSA types 3, 5, and 7
E. It is set when MP-BGP routers are redistributed into OSPF
Answer: C D
NO.146 Which two statements about ICMP unreachable messages are true?(Ch oose two)
A. They are sent when a route to the destination is missing from the routing table
B. They can be enabled and disabled on a device only on a global level
C. They are sent when a destination address responds to an ARP request
D. They include the entire packet so that the source can identify the process that generated the
message
E. They include a portion of the original data so that the source can identify the process that
generated the message
Answer: A C
NO.147 Which two types of threshold are configured for tracking object? (Choose two)
A. delay
B. percentage
C. bandwidth
D. administrative distance
E. weight
Answer: B E
NO.148 Which two different configurations can you apply to a device to block incoming SSH access?
(Choose two.)
55
A. Option A
B. Option B
C. Option C
D. Option D
E. Option E
Answer: B C
NO.149 WHICH COMMAND DO YOU ENTER ON ROUTER R6 SO THAT BGP SUPPORTS MULTIPLE
PROTOCOLS?
56
A. R6(config-router-af)#bgp additional-path install

B. R6(Config-router)#no address-family ipv6 unicast
C. R6(config-router)#no bgp default ipv4-multicast
D. R6(confi-router)#bgp default ipv4-multicast
Answer: B
NO.150 21. Which protocol can you use to remotely install an IOS image on a Cisco switch?
A. SFTP
B. NetFlow
C. FTP
D. SNMP
Answer: C
NO.151 Which two statements about NHRP in a DMVPN environ two.)

A. It routes traffic through the tunnel.
B. It provides address resolution to route traffic.
C. It can authenticate VPN endpoints.
D. It requires each endpoint to have a unique network ID.
E. It can identify PIM-SM RPs over a tunnel.
Answer: B C
NO.152 Refer to exhibit.
A packet capture indicates that router is not forwarding the DHCP packets that it receives on
interface FastEthernet command must be entered in global configuration mode to resolve this issue?
A. ip forward-protocol
B. ip DHCP relay
C. ip helper
D. service DHCP
Answer: A
NO.153 Which command prevents routes from sending routing updates through a router intercaes?
A. distribute-list in
B. passive-interface
C. default-metric
D. distribute-list out
Answer: B
NO.154 Which three functionalities are specific to stateful NAT64? (Choose three.)
A. It conserves IPv4 addresses.
57
B. It requires IPv4-translatable IPv6 addresses.

C. No constraint is put on the number of endpoints due to 1:N translation.
D. It helps ensure end-to-end address transparency and scalability.
E. A state or bindings are created on every unique translation.
F. It requires either manual or DHCPv6-based address assignment for IPv6 hosts.
Answer: A C E
All neighbor routers are in the BGP peer group named PEER-1 All passwords are configured as Cisco.
These messages are logged to the console of router DSW1. which is peering with router Core. Which
two configurations allow a peering session to form between DSW1 and the Core? (Choose two.)
A. Core(config-router)#neighbor 5.0.0.5 peer-group PEER-1 Core(config-router)#neighbor PEER-1
password cisco
B. DSW1(config-router)#neighbor 5.0.0.5 peer-group PEER-1 DSW1(config-router)#neighbor PEER-1
password cisco
C. DSW1(config-router)#neighbor 51.51.51.1 peer-group PEER-1 DSW1(config-router)#neighbor
PEER-2 password cisco
D. Core(config-router)#neighbor 51.51.51.1 peer-group PEER-1 Core(config-router)#neighbor PEER-1
password cisco
E. Core(config-router)#neighbor 5.0.0.5 peer-group PEER-2 Core(config-router)#neighbor PEER-1
password cisco
Answer: A C
NO.156 How can you minimize unicast flooding in a network?

A. Configure HSRP on two routers, with one subnet preferred on the first router and different subnet
preferred on the second router.
B. Set the router's ARP timeout value to be the same as the timeout value for Layer forwarding table
entries.
C. Set the router's ARP timeout value to greater than the timeout value for Layer 2 forwarding table
entries.
D. Set the router's ARP timeout value to less than the timeout value for Layer 2 forwarding table
entries.
Answer: B
NO.157 What is the hop count that is advertised for an unreachable network by a RIP routes that
uses poison reverse?
A. 0
B. 15
58
C. 16
D. 255
Answer: C
NO.158 You are a network engineer with ROUTE.com, a small IT company. ROUTE.com has two
connections to the Internet; one via a frame relay link and one via an EoMPLS link. IT policy requires
that all outbound HTTP traffic use the frame relay link when it is available. All other traffic may use
either link. No static or default routing is allowed.
Choose and configure the appropriate path selection feature to accomplish this task. You may use the
Test Workstation to generate HTTP traffic to validate your solution.
59
Answer:
Explanation
We need to configure policy based routing to send specific traffic along a path that is different from
the best path in the routing table.
Here are the step by Step Solution for this:
1) First create the access list that catches the HTTP traffic:
R1(config)#access-list 101 permit tcp any any eq www
2) Configure the route map that sets the next hop address to be ISP1 and permits the rest of the
traffic:
R1(config)#route-map pbr permit 10
R1(config-route-map)#match ip address 101
R1(config-route-map)#set ip next-hop 10.1.100.2
R1(config-route-map)#exit
R1(config)#route-map pbr permit 20
3) Apply the route-map on the interface to the server in the EIGRP Network:
R1(config-route-map)#exit
R1(config)#int fa0/1
R1(config-if)#ip policy route-map pbr
R1(config-if)#exit
R1(config)#exit
First you need to configure access list to HTTP traffic and then configure that access list. After that
configure the route map and then apply it on the interface to the server in EIGRP network.
60
NO.159 49. Which two OSPF router types can perform summarization in an OSPF network?(Choose
two)
A. backbone router
B. area border router
C. summary router
D. a autonomous system boundary router
E. internal router
Answer: B D
NO.160 Which statement about stateless and tasteful IPv6 auto configuration is true?
A. Both stateless and stateful configuration require additional setup.
B. Stateless autofiguration requires no additional setup whereas stateful autoconnguration requires
additional setup
C. Stateless autoconftguraton requires additional setup whereas stateful autoconfiguration requires
no additional setup.
D. Both stateless and stateful autoconfiguration require no additional setup.
Answer: D
NO.161 In which two areas does OSPF send a summary route by default? (Choose two.)
A. NSSA
B. backbone
C. stub
D. normal
E. totally stubby
Answer: C D
NO.162 Which LAN feature enables a default gateway to inform its end de
A. HSRP
B. proxy ARP
C. ICMP redirects
D. ICMP unreachable
Answer: C
NO.163 After configuring RIPng on two routers that are connected via a WAN link, a network
engineer notices that the two routers cannot exchange routing pdates. What is the reason for this?
A. Either a firewall between the two routers or an ACL on the router is blocking UDP 521
B. Either a firewall between the two routers or an ACL on the router is blocking TCP 520
C. Either a firewall between the two routers or an ACL on the router is blocking TCP 521
D. Either a firewall between the two routers or an ACL on the router is blocking UDP 520.
Answer: A
NO.164 Which value Identifies VPNs in an EVN environment?

A. route target
61
B. VLAN ID
C. DLCI
D. virtual network tag
Answer: D
NO.165 Which three TCP enhancements can be used with TCP selective acknowledgments? (Choose
three)
A. MTU window
B. TCP path discovery
C. explicit congestion notification
D. header compression
E. time stamps
F. keepalive
Answer: C E F
NO.166 Which two tasks must you perform to configure a BGP peer group?(Choose two)
A. Configure the soft-update value
B. Activate the default route
C. Set the advertisement Interva
D. Activate each neighbor
E. Assign neighbors to the peer group
Answer: D E
NO.167 Which two commands must be used to troubleshoot high memory usage for a process?
A. router#show memory allocating-process table
B. router#show memory processor statistics
C. router#show memory events
D. router#show memory summary
E. routertfshow memory dead
Answer: A D
NO.168 In which two ways can split horizon issues be overcome in a Frame Relay network
environment? (Choose two)
A. enabling split horizon
B. configuring one physical serial interface with Frame Relay to various remot
C. disabling split horizon
D. configure a loopback interface with Frame Relay to various remote site
E. configuring multiple subinterfaces on a single physical interface to
Answer: C E
NO.169 Drag and Drop the AAA features from the left onto the correct description on the right
Select and Place:
62
Answer:
Explanation
NO.170 When does a Cisco router send an ICMP redirect?

A. when the packet's source and destination VRFs are different
B. when the packet is source-routed
C. when the packet's destination has load-balanced entries in the route table
D. when the packet's ingress and egress interfaces are the same
Answer: D
Explanation
63
NO.171 A network engineer is enabling RIPng on a new customer link. Under which configuration
mode is RIPng enabled?
A. Global
B. Router
C. Interface
D. IPv6
Answer: A
NO.172 Which types of LSAs are present in the stub area?

A. LSA type 1 and 2
B. LSA type 1. 2. 3, 4. and 5
C. LSA type 1 2, and 3
D. LSA type 3 and 5
Answer: C
NO.173 Which LSA types can exist only in an OSPF NSSA area?
A. type 1 LSA
B. type 3 LSA
C. type 5 LSA
D. type 7 LSA
Answer: D
NO.174 Which feature eliminates the need for Cisco Express forwarding to maintain a route cache?
A. MAC address table
B. adjacency table
C. FIB
D. RIB
Answer: C
Explanation
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/XE3-6-0E/15-
22E/configuration/guide/xe-360-config/cef.pdf
64
NO.175 A customer requests policy-based routing Packets arriving from source 209 165 200 225
should be sent to the next hop at 209 165 200 227 with the precedence bit set to priority. Packets
arriving from source 209 165 200
226 should be sent to the next hop at 209 165 200 228 with the precedence bit set to critical Which
configuration completes these requirements'?
A customer requests policy-based routing Packets arriving from source 209 165 200 225 should be
sent to the next hop at 209 165 200 227 with the precedence bit set to priority Packets arriving from
source 209.165.200
226 should be sent to the next hop at 209 165 200 228 with the precedence bit set to critical. Which
configuration completes these requirements?
A)
65
B)
C)
D)
66
A. Option A
B. Option B
C. Option C
D. Option D
Answer: A
NO.176 Which command do you enter on router R6 so that BGP supports multiple protocols'?
A. R6(config-router-af)#bgp additional-paths install
B. R6(config-router-af)#no bgp default ipv4-multicast
C. R6(config-router)#no address-family ipv4 unicast
D. R6(config-router)#bgp default ipv4-multicast
E. R6(config-router)#no bgp default ipv4-unicast I
Answer: E
NO.177 Traffic from R1 to R6 loopback address is load shared between R1-R2-R4-R6 and R1-R3-R5-
R6 path. What is the ratio of the traffic over each path?
A. 1:1
B. 1:5
C. 6:8
D. 19:80
Answer: D
NO.178 Which two actions are common methods for migrating a network from one network
protocol to another?
(choose two)
67
A. Channing the relative administrative distance of the two routing protocols.

B. Channing the network Ip address and bringing up the addresses using the new routing protocol
C. removing the currency protocol and implementing the new routing protocol
D. redistributing from the current routing protocol to the new routing protocol
E. disabling IP routing globally and implement the new routing protocol
Answer: B D
NO.179 Which two statements about Frame Relay LMI autosense are true on a Router?(Choose two
)
A. It requires the line protocol to be up
B. it operates when the line is up but the line protocol is down
C. It requires the LMI type to be explicitly configured
D. It operates on Frame Relay DTE interfaces
E. It operates on Frame Relay DCE interfaces
Answer: B D
NO.180 Which two statements about DMVPN are true?

A. Multicast traffic is not supported
B. It requires full-mesh connectivity on the network
C. IPsec encryption is not supported with statical addressed spokes
D. It uses NHRP to create a mapping database of spoke addresses
E. It supports dynamic addresses for spokes in a hub-and-spoke VPN topology
Answer: D E
NO.181 A network engineer is configuring two dedicated internet connection within the internet
nodule.
One connection is primary connection to all wired business communication. While the other is the
primary connection for all customer wireless traffic?
A. PBR
B. IP QoS
C. MMC
D. IP SLA
E. IP SAA
Answer: A
NO.182 Which two BGP neighbor states are valid? (Choose two)
A. DROTHER
B. established
C. stuck in active
D. unknown
E. 2-WAY
F. active
Answer: B F
68
NO.183 10. Device R1 has 1 Gigabit and 10 Gigabit Ethernet interfaces, which command do you
enter so that it takes full advantage of OSPF costs?
A. R1(config router) #auto-cost reference-bandwidth 10000
B. R1(config route-map) #set metric 10000000000
C. R1(config if) #ip ospf cost 10000
D. R1(config router) #auto-cost reference-bandwidth 10000000000
E. R1(config if) #ip ospf cost 10000000000
F. R1(config route-map) #set metric 10000
Answer: A
NO.184 Which two statements about NetFlow templates are true? (Choose two)
A. Only NetPlow version 5 is template-based.
B. Templates can increase bandwidth usage
C. NetFlow version 5 and version 9 are template-based
D. Only NetFlow version 9 is template-based
E. They can increase overall performance
F. They can reduce bandwidth usage
Answer: B D
NO.185 A network engineer wants to display the statistics of an active tunnel on a DMVPN network
Which command must the administrator execute to accomplish this task?
A. router#show crypto ipsec so
B. router#show crypto isakmp sa
C. router#show crypto isakmp peers
D. routerfaceshow crypto ipsec transform-set
E. router#show crypto engine connections active
Answer: A
NO.186 Which option is one way to mitigate symmetric routing on an active/active firewall setup for
TCP based connections?
A. performing packet captures
B. disabling asr-group commands on interfaces that are likely to receive asymetnc traffic
C. replacing them with redundant routers and allowing load balancing
D. disabling stateful TCP checks
Answer: D
NO.187 Which two statements about GRE tunnel keys are true? (Choose two.)
A. The key ID must be the same on each device.
B. They prevent the injection of unwanted frames.
C. They prevent the injection of unwanted packets.
D. They must be stored to a keychain.
E. They provide the highest level of security that is available.
69
Answer: A C
NO.188 Which two statements are examples of the difference between IPV4 and IPV6 EIGRP?
(Choose two)
A. Network command is not used m IPv6
B. DUAL is used for route calculations
C. IPv6 keyword is used in many EIGRP commands
D. DUAL is not used for route calculations
E. Network command is used in IPv6
Answer: A C
NO.189 When Unicast Reverse Path Forwarding is configured on an interface, which action does the
interface take first when it receives a packet?
A. It checks the ingress access lists
B. It verifies a reverse path via the FIB to the source
C. It checks the egress access lists
D. It verifies that the source has a valid CEF adjacency
Answer: D
NO.190 A network engineer applies the command ip tcp adjust-mss <bytes> under interface
configuration mode. What is the result?
A. The probability of SYN packet truncation is increased
B. The optimum MTU value for the interface is set
C. The UDP session is inversely affected
D. The probability of dropped or segmented TCP packets is decreased
Answer: B
NO.191 Which access list entry checks for an ACK within a packet TCP header?
A. access-list 49 permit ip any any eq 21 tcp-ack
B. access-list 149 permit tcp any any eq 21 established
C. access-list 49 permit tcp anyany eq 21 tcp-ack
D. access-list 49 permit tcp any any eq 21 established
Answer: B
NO.192
70
Refer to the exhibit. Which two reasons for IP SLA tracking failure are true*? (Choose two)
A. A route back lo the R1 LAN network is missing in R2
B. The threshold value is wrong
C. The destination must be 172 30 30 2 for icmp-echo
D. The default route has wrong next hop IP address
E. The source-interface is configured incorrectly
Answer: A E
NO.193 Which two commands must you configure in the calling router to support the PPPoE client?
(Choose two.)
A. pppoe enable group
B. mtu
C. peer default ip address pool
D. pppoe-client dial-pool-numb
E. bba-group pppoe
Answer: B D
NO.194 Which DHCP option provides a TFTP server that cisco phones can use to download a
configuration?
A. DHCP Option 82
B. DHCP Option 68
C. DHCP Option 66
D. DHCP Option 57
Answer: C
NO.195 Which two statements about IP access lists are true?(Choose two)
A. Extended access lists must include port numbers
B. They support wildcard masks to limit the address bits to which entries are applied
C. Entries are applied to traffic in the order in which they appear
71
D. They end with an implicit permit

E. IP access lists without at least one deny statement permit all traffic by default
Answer: B C
NO.196 What is the default authentication in RIPv2 when authentication is enabled?

A. enable password authentication
B. MD5 authentication
C. SHA1 authentication
D. plaintext
authentication
Answer: D
NO.197 Which value determines the amount of traffic that a network path can hold in transit?
A. route cache setting
B. maximum window size
C. bandwidth delay product
D. MSS
Answer: D
Which effect of this configuration is true?

A. The device sends SNMP traps related to BGP operations to host 192.168 1.128
B. It configures an ACL to protect SNMP managers from receiving BGP traps.
C. it configures the device to use string ciscotest for read and write access to any SNMP manager on
the network.
D. it configures the device to communicate with other devices in the ciscotest community using
SNMPv3
Answer: A
NO.199 What happens when unicast flood protection is triggered on a VLAN?

A. The VLAN is shut down
B. Traffic on the VLAN is load-balanced across multiple links
C. The VLAN is removed from the VLAN database
D. Traffic on the VLAN is passed to another VLAN with lower load
Answer: A
72
NO.200 Which address is an IPv6 multicast addreess?

A. 2002 0 :0: 0 :0 :0 :0: 2
B. 00020 0 :0:0: 0:0:2
C. FF02.0.:0 :0 :0:0 :0 :2
D. FE02 0:0 :0 :0 :0:0:2
Answer: C
NO.201 Which task must you perform to implement EIGRP for IPv6 on a device?
A. Use the ipv6 cef command to enable Cisco Express Forwarding on the device.
B. Configure a loopback interface on the device.
C. Manually configure the router ID
D. Statically configure a neighbor
Answer: C
NO.202 27. Under which circumstance can TCP starvation occur?

A. when DNS and TFTP traffic are transmitted on the same link
B. when TCP traffic is blocked by an ACL
C. when UDP traffic is processed in a policy-map before TCP traffic
D. when Http and Https traffic are transmitted on the same link
E. when TCP and UDP traffic are mixed in the same class of service
Answer: E
NO.203 Which two protocols can cause TCP starvation? (Choose two)
A. SMTP
B. TFTP
C SNMP
C. FTP
D. HTTPS
Answer: A B
NO.204 Which two types of threshold can you configure for tracking objects? (Choose two.)
A. weight
B. MTU
C. percentage
D. bandwidth
E. delay
F. administrative distance
Answer: A C
73
You notice that traffic from R1 to the 192.168.10 0/24 network prefers the path through R3 instead
of the least-cost path through R2.What is the most likely reason for this route selection?
A. OSPF prefers external routes over interarea routes.
B. OSPF prefers interarea routes over intra-area routes.
C. OSPF prefers external routes over intra-area routes.
D. OSPF prefers intra-area routes over interarea routes
Answer: D
NO.206 After reviewing the EVN configuration, a network admin notice that a predefined EVN,
which is know as vnet global was configured. What is the purpose of this EVN?
A. It refers to the global context and corresponds to the default RIB.
B. It aggregates and carries dot1q tagged traffic.
C. It defines the routing scope for each particular EVN edge interface.
D. It safeguards the virtual that is preconfigure to avoid mismatched routing instances.
Answer: A
74
NO.207 A user is attempting to authentication on the device connected to a TACACS+ server but the
server require more information from the user to complete authentication. Which response does the
TACACS+ daemon return?
A. ACCEPT
B. ERROR
C. REJECT
D. CONTINUE
Answer: D
NO.208 A network engineer execute the show ip cache flow command. Which two types of
information are displayed in the report that is generated? (Choose two)
A. MLS flow traffic
B. flow samples for specific protocols
C. IP packets distribution flow expert statistic
D. top takers
Answer: B D
NO.209 Which three benefits does the Cisco Easy Virtual Network provide to an enterprise network?
(Choose three)
A. simplified Layer 3 network virtualization
B. improved shared services support
C. enhanced management, troubleshooting, and usability
D. reduced configuration and deployment time for dot1q trunking
E. increased network performance and throughput
F. decreased BGP neighbor configurations
Answer: A B C
NO.210 A network engineer executes the commands logging host 172.16.200.225 and logging trap 5
Which action results when these two commands are executed together?
A. Logging messages that have any severity level are sent to the remote server 172.16 200.225
B. Logging messages that have a severity level of "notifications'* and above (urnericay tower) are
sent to the remote server 172.16.200.225
C. Logged information is stored locally, showing the source as 172.16.200.225
D. Logging messages that have a debugging severity level are sent to the remote server
172.16.200.225
Answer: B
NO.211 What is the advertised distance for the 192.168.46.0 network on R1?
A. 333056
B. 1938688
C. 1810944
D. 307456
Answer: C
75
NO.212 Which feature can be used to reduce the number of ICMP unreachable messages egressing
a router?
A. ICMP rate-limiting
B. asymmetric routing
C. URPF
D. ip unreachables command
Answer: A
NO.213 Which command is implemented to configure an enable password that uses an encrypted
password from another configuration?
A. enable secret 6 $abc/.!#.Cd34$!ao0
B. enable secret Sabc%!#.Cd34S!ao0
C. enable secret 5 $abc%!#.Cd34$!ao0
D. enable secret 15 $abc%!#.Cd34$!ao0
E. enable secret 7 Sabc%!#.Cd34$!aoO
Answer: D
NO.214 Which two configurations does a PPPoE client support? (Choose two)
A. The client is installed on the same network device as the server
B. The client is connecting over an ATM PVC
C. The client is connected to multiple hosts over DMVPN
D. Eight clients are configured on a single CPE
E. The client is installed on a native IPv6 network
Answer: A B
NO.215 Which SNMP model and level can provide DES encryption?
A. SNMPV2noAuthNoPrry
B. SNMPv3authNoPriv
C. SNMPv3 authEn
D. SNMPv3noAuthNoPrv
Answer: C
NO.216 Which feature mitigates fragmentation issues caused by endpoint hosts?

A. MSS HMTU
B. ICMP
C. ICMP DF bit
D. TCP How Control
Answer: B
NO.217 Which two statements about OSPFv3 are true?(choose two)

A. The router ID is configured as an IPv6 address.
B. It uses loopback IPv6 addresses to form neighbor relationships.
76
C. The router ID is configured as an IPv4 address.

D. It uses LSA type 6 for intra-area prefixes.
E. It is backwards-compatible with OSPFv2 through the use of sham link.
F. It uses link-local addresses to form neighbor relationships.
Answer: C F
A user calls from another branch office with a request to establish a simple VPN tunnel to test a new
router's tunneling capability. Based on the configuration in the exhibit, which type of tunnel was
configured?
A. IPsec site-to -site
B. 6to4
C. PPTP
D. EZVPN
Answer: B
NO.219 ROUTE.com is a small IT corporation that has an existing enterprise network that is running
IPv6 0SPFv3.
Currently OSPF is configured on all routers. However, R4's loopback address (FEC0:4:4) cannot be
seen in R1's IPv6 routing table. You are tasked with identifying the cause of this fault and
implementing the needed corrective actions that uses OPSF features and does not change the
current area assignments. You will know that you have corrected the fault when R4's loopback
address (FEC0:4:4) can be seen in RTs IPv6 routing table.
Special Note: To gain the maximum number of points you must remove all incorrect or unneeded
configuration statements related to this issue.
77
78
79
Answer:
Explanation
To troubleshoot the problem, first issue the show running-config on all of 4 routers. Pay more
attention to the outputs of routers R2 and R3 The output of the "show running-config" command of
R2:
The output of the "show running-config" command of R3:
80
We knew that all areas in an Open Shortest Path First (OSPF) autonomous system must be physically
connected to the backbone area (Area 0). In some cases, where this is not possible, we can use a
virtual link to connect to the backbone through a non-backbone area. The area through which you
configure the virtual link is known as a transit area. In this case, the area 11 will become the transit
area. Therefore, routers R2 and R3 must be configured with the area <area id> virtual-link <neighbor
router-id>command. + Configure virtual link on R2 (from the first output above, we learned that the
OSPF process ID of R2 is 1):
R2>enable
R2#configure terminal
R2(config)#ipv6 router ospf 1
R2(config-rtr)#area 11 virtual-link 3.3.3.3
Save the configuration:
R2(config-rtr)#end
R2#copy running-config startup-config
(Notice that we have to use neighbor router-id 3.3.3.3, not R2's router-id 2.2.2.2) + Configure virtual
link on R3 (from the second output above, we learned that the OSPF process ID of R3 is 1 and we
have to disable the wrong configuration of "area 54 virtual-link 4.4.4.4"):
R3>enable
R3#configure terminal
R3(config-rtr)#no area 54 virtual-link 4.4.4.4
R3(config-rtr)#area 11 virtual-link 2.2.2.2
Save the configuration:
R3(config-rtr)#end
R3#copy running-config startup-config
You should check the configuration of R4, too. Make sure to remove the incorrect configuration
statements to get the full points.
R4(config-router)#no area 54 virtual-link 3.3.3.3
R4(config-router)#end
After finishing the configuration doesn't forget to ping between R1 and R4 to make sure they work.
Note. If you want to check the routing information, use the show ipv6 route command, not "show ip
route".
81
You are configuring the R1 Serial0 interface for a multipoint connection. Drag and drop the required
configuration statements from the left onto the .corresponding locations from the diagram on the
right.
Answer:
82
Explanation
NO.221 A network engineer executes the show IP Cache flow command, Which two types of
information are displayed in the report that is generated? (Choose two.)
A. flow export statistics
B. SMLS flow traffic
C. flow samples for specific protocols
D. top talkers
E. IP packet distribution
Answer: A C
NO.222 What are two important differences between OSPFv2 and OSPFv3? (Choose
two.)
A. Only OSPFv3 provides support for IPv6.
B. Only OSPFv3 automatically chooses a router ID for the local device.
C. Only OSPFv3 supports multiple OSPF instances on a single link.
D. Only OSPFv3 automatically enables interfaces when you create them in device configuration
mode.
E. Only OSPFv3 automatically detects OSPF neighbors on an NBMA interface.
Answer: A C
83
Which LSA type does R3 propagate into Area 1 for the 192.168.10.0/24 network?
A. type 3 LSA
B. type 5 LSA
C. type 7 LSA
D. type 10
Answer: B
NO.224 Which option is a perquisite for stateful NAT64?

A. application layer gateway
B. ICMP64
C. DNS64
D. IPsec for IPv6
Answer: C
NO.225 Which action is one way to mitigate asymmetric routing on an active/active firewall setup
foi TCP-based connections'?
A. disabling asr-group commands on interfaces that are likely to receive asymmetnc traffic
B. performing packet captures
C. disabling stateful TCP checks I
D. replacing them with redundant routers and allowing load balancing
Answer: C
NO.226 Which option is the best for protecting CPU utilization on a device?
A. fragmentation
B. COPP
C. ICMP redirects
D. ICMPunreachabl messages
Answer: B
NO.227 Drag and drop the ACL types from the left onto the correct description on the right.
84
Answer:
Explanation
NO.228 Which two statements about Frame Relay point-to-point connections are true?(Choose two
)
A. They use two DLCIs to communicate with multiple endpoints over the Frame Relay cloud
B. The device can establish a point-to-point connection to the cloud without a DLCI
C. Changing a point-to-point subinterface to a different type requires the device to be reloaded
D. They can operate normally without a DLCI map
E. Each physical interface that extends to the Frame Relay cloud can support a single Svc
85
Answer: A C
NO.229 Which two statements about EVnS are true? (Choose two)
A. VRFs using MPLS require a trunk interface that uses EVN
B. All EVNs within a trunk interface can share the same IP infrastructure
C. Each EVN within a trunk interface must be configured separately
D. Commands that are specified once under a trunk interface can be inherited by all EVNs
E. VRF-Lite requires a trunk interface that uses EVN
Answer: B D
NO.230 Which statement about IP SLA feature is true?

A. It ensures that there are appropriate levels of service for network applications
B. It classifies various traffic types by examining information within Layers 3 through 7
C. It measures how the network treats traffic for specific applications by generating traffic that bears
similar characteristics to application traffic.
D. It keeps track of the number of packets and bytes that are observed in each flow by storing
information in a cache flow
Answer: A
NO.231 Which two tasks does a DHCP relay agent perform?(Choose two)
A. It forwards DHCPOFFER and DHCPCOMPLETE messages to the DHCP client.
B. It forwards DHCPDISCOVER and DHCPREQUEST messages to the DHCP server
C. It forwards DHCPHELLO and DHCPREQUEST messages to the DHCP server.
D. It forwards DHCPREQUEST and DHCPACK messages to the DHCP server!
E. It forwards DHCPOFFER and DHCPACK messages to the DHCP client.
Answer: B E
NO.232 Which two statements about VRF-Lite configuration are true? (Choose two)
A. They support ISIS.
B. Each customer has its own dedicated TCAM resources.
C. Different customers can have overlapping IP addresses on different VPNs.
D. They support the exchange of MPLS labets.
E. They support a maximum of 512 000 routes.
F. Each customer has its own private routing table.
Answer: B F
NO.233 Which technology is required on an EVN trunk interface?

A. NAT
B. 802.1q
C. VRF-Lite
D. IS-IS
Answer: C
86
NO.234 What does stateful NAT64 do that stateless NAT64 does not do?
A. Stateful NAT64 maintains bindings of IPv4 to IPv6 link-local addresses.
B. Stateful NAT64 translates IPv4 to IPv6.
C. Stateful NAT64 translates IPv6 to IPv4.
D. Stateful NAT64 maintains bindings or session state while performing translation.
Answer: D
NO.235 What does the following access list, which is applied on the external interface FastEthernet
1/0 of the perimeter router, accomplish?
A. It prevents private internal addresses to be accessed directly from outside

B. It filters incoming traffic from private address ranges 10 0 0 0-10 0 0 255,172 16.0 0-172.31.255
255.192 168 0 0-192 168 255 255 and logs any intrusion attempts
C. It prevents the internal network from being used in spoofed denial of service attacks and logs any
exit to the Internet
D. It filters incoming traffic from private addresses in order to prevent spoofing and logs any
intrusion attempts
Answer: B
NO.236 A network engineer executes the show crypto ipsec sa command which three pieces of
information are displayed in the output? (Choose three)
A. tagged packets
B. untagged packets
C. inbound crypto map
D. path MTU
E. invalid identity packets
F. remaininig key
Answer: C D F
NO.237 Which two steps must you perform to allow access to a device when the connection to a
remote TACACS+ authentication server fails? (Choose two)
A. include the local keyword in the AAA configuration
B. Configure accounting to reference the log of previously authenticated connections
C. Configure the device to accept Telnet and SSH connections.
D. Remove the aaa new model command from the global configuration
E. Configure a local username and password on the device
87
Answer: B E
NO.238 Which is the minimum privilege level to allow a user to execute all user-level commands but
prohibits enable-level commands by default?
A. level 0
B. level 1
C. level 14
D. level 15
E. level 16
Answer: B
NO.239 Which routing protocol routes traffic through the best path and second best path at the
same time?
A. EIGRP
B. BGP
C. OSPF
D. RIP
Answer: B
NO.240 Which task must you perform to enable a point-to-point Frame Relay connection?
A. Enable inverse ARP.
B. Configure the encapsulation type.
C. Configure static address mapping.
D. Disable inverse ARP.
Answer: C
NO.241 Which interfaces type does a PPPoE client use to establish a session?
A. dialer
B. virtual-template
C. physical
D. loopback
Answer: A
NO.242 A router receives a routing advertisement for 10.1.1.0/24 from an EIGRP peer and from an
OSPF peer, Which route does the router install in the routing table, and for which reason?
A. the OSPF route, because the administrative distance is lower
B. the EIGRP route, because the metric is lower
C. the OSPF route, because the metric is lower
D. the EIGRP route, because the administrative distance is lower
Answer: D
NO.243 Which three NTP operating modes must the ntp trusted-key command be configured on for
authentication to operate properly?(Choose three)
88
A. client
B. interface
C. stratum
D. server
E. peer
F. broadcast
Answer: A D F

Which two reasons for IP SLA tracking failure are true*? (Choose two )
A. A route back to the R1 LAN network is missing in R2

B. The threshold value is wrong
C. The destination must be 172 30 30 2 for icmp-echo
D. The default route has wrong next hop IP address
E. The source-interface is configured incorrectly
Answer: A E
NO.245 Which condition must be met before you can configure SSH on a device running Cisco loS?
A. The device must have an auxilary port.
B. The device must have a modem connection.
C. The loS must be a crypto in
D. Telnet must be disabled on the device
Answer: C
NO.246 A network engineer wants to implement an SNMP process for host machines using the
strongest security available which command accomplishes this task?
A. router(confi)#snmp-server-host 172-16-200.225 traps v3
B. router(confi)#snmp-server-host 172-16-200.225 traps v2c auth
C. router(confi)#snmp-server-host 172-16-200.225 traps v1
89
D. router(confi)#snmp-server-host 172-16-200.225 traps v2c

Answer: A
NO.247 A router was configured with the EIRGP stub command. The router advertises which types
of routes?
A. static and summary
B. connected, static, and summary
C. connected and static
D. connected and summary
Answer: D
NO.248 Which SNMP security level is available across all versions of the protocol?
A. AuthPriv
B. NoAuthPriv
C. AuthNoPriv
D. NoAuthNoPriv
Answer: A
NO.249 In which network environment is AAA with RADIUS most appropriate?

A. when Apple Talk Remote Access Is in use
B. when NetBIOS Frame Control Protocol is in use
C. when users require access to only one device at a time
D. when you need to separate all AAA services
Answer: C
NO.250 Which feature can automatically assign IP addresses IP addresses in a PPPoE environment?
A. DHCP
B. BOOTP
C. PPP
D. APPA
Answer: C
90

300-101 V23.75

Uploaded by

Copyright:

300-101 V23.75

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

300-101 V23.75

Uploaded by

Copyright:

IT Certification Guaranteed, The Easy Way!

Title : Implementing Cisco IP Routing

NO.3 Which adverse circumstance can the TTL feature prevent?

NO.4 Which of the following situations results in a routing loop

C. unicast IPv4 addresses

NO.10 Which two features were added in MSCHAP version 2?(choose 2)

NO.13 Refer to the exhibit.

NO.20 What percent of R1 interfaces bandwidth is ERIGRP allowed to use?

NO.25 Which security feature can protect DMVPN tunnels?

NO.26 Refer to the exhibit.

A. The default router through 10.0.1 is never used.

NO.28 In which scenario can asymmetric routing occur?

NO.29 Which feature or technology is supported with stateful NAT64?

Show ip route in host A

A. Filter routes manually using prefix lists

NO.43 What type of route filtering is occurring on R6?

NO.44 Refer to the exhibit.

NO.45 Refer to the exhibit.

Which statement describes the effect of this configuration on a Cisco router'?

NO.47 Which statement about conditional debugging is true?

A. It can support only one condition at a time

NO.55 Which problem can be caused by latency on a UDP stream?

NO.57 Which two causes of latency are true?(choose two)

NO.60 Refer to the exhibit.

NO.65 Refer to the exhibit.

NO.66 What is VRF-Lite?

NO.69 Which two features does RADIUS combine?(Choose two)

NO.72 Refer to the exhibit.

Which routes from OSPF process 5 are redistributed into EIGRP?

forwarding in loose mode?

NO.78 Refer to the exhibit.

NO.81 What is the role of a route distinguisher in a VRF-Lite setup implementation?

NO.82 Which calculation is used to determine the default EIGRP metric?

NO.93 Refer to the exhibit.

R3(config)#exit R3(config-router)#router eigrp 100 R3(config-router)#redistribute ospf 1 metric

NO.97 Which OSPF network type uses a DR?

NO.101 Refer to the exhibit.

NO.102 Refer to the exhibit.

NO.110 Which protocol does VRF-Lite support?

NO.112 Which technology supports overlapping IP addresses on a single interface?

NO.115 Refer to the exhibit. Which effect of this configuration is true?

A. It designates the interface as a GRE tunnel endpoint

NO.116 During which DMVPN phase is spoke to-spoke communication enabled?

NO.118 Which LSA type in 0SPFv3 is used for link-local u

NO.125 Which feature filters information at the interface level?

A. R1 redistributes network 10.1.80.0/24 into EIGRP without changing the mask

NO.127 Refer to the exhibit.

What is indicated by the show ip cef command for an address?

NO.130 Refer to the exhibit.

NO.131 Which statement about dynamic NAT is true?

C. It uses the overload command to map addresses.

NO.132 What is the administrative distance of an EIGRP summary route?

NO.133 Which command must you configure globally to supportRIPng?

NO.142 Refer to the exhibit.

NO.143 Refer to the exhibit.

A. R6(config-router-af)#bgp additional-path install

NO.151 Which two statements about NHRP in a DMVPN environ two.)

NO.152 Refer to exhibit.

B. It requires IPv4-translatable IPv6 addresses.

NO.155 Refer to the exhibit.

NO.156 How can you minimize unicast flooding in a network?

NO.164 Which value Identifies VPNs in an EVN environment?