Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 67 views

    Air Compressor Flange Removal and Installation Has Been Added To The Workshop Manual

    Uploaded by

    Chandra Sutawijaya
    Cara perbaikan power steering Eps toyota

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Air Compressor Flange Removal and Installation Has Been Added To The Workshop Manual

    Uploaded by

    Chandra Sutawijaya
    67 views4 pages
    Cara perbaikan power steering Eps toyota

    Original Title

    Eps toyota

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Cara perbaikan power steering Eps toyota

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    67 views4 pages

    Air Compressor Flange Removal and Installation Has Been Added To The Workshop Manual

    Uploaded by

    Chandra Sutawijaya
    Cara perbaikan power steering Eps toyota

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 4

    NUMBER: 08 MBE 4000-3 S.M. REF.: 11.

    1 ENGINE: EPA07 MBE 4000 DATE: September


    2008

    SUBJECT: AIR COMPRESSOR FLANGE

    PUBLICATION: DDC-SVC-MAN-0026
    Air compressor flange removal and installation has been added to the workshop manual.
    REMOVAL OF AIR COMPRESSOR FLANGE
    Remove as follows:
    1. Shut off engine and apply the parking brake, chock the wheels, disconnect vehicle battery
    power, and perform any other applicable safety steps.
    2. Remove the two bolts attaching the power steering pump to the air compressor.

    NOTE:
    Do not remove the power steering lines. Tie up the lines and move the pump out of the way.

    1. Power Steering Pump Mounting Bolt 5. Air Compressor Housing


    2. Power Steering Pump 6. Air Compressor Mounting Bolt
    3. O-ring 7. Air Compressor Flange
    4. Cross Plate

    Figure 1 Air Compressor

    3. Remove the cross plate between the compressor and the power steering pump.
    4. Discard the O-ring between the power steering pump and the air compressor.
    NOTICE:
    When removing the flange, make sure not to damage the
    crankshaft journal or crankshaft bearing.

    5. Remove the four bolts attaching the air compressor flange to the air compressor housing.
    6. Discard O-ring between the air compressor flange and air compressor housing.
    7. Inspect air compressor flange, bearing, and O-ring surfaces for damage. Replace if necessary.

    INSTALLATION OF AIR COMPRESSOR FLANGE


    Installation steps are as follows:
    1. Install the new O-ring between the air compressor flange and air compressor housing.
    NOTICE:
    Make sure to not damage the crankshaft journal or crankshaft
    bearing while installing.

    2. Install the air compressor flange using the four bolts. Torque to 30 N·m (22 lb·ft).

    NOTE:
    Use grease to hold the cross plate in place while installing the power steering pump.

    3. Install the cross plate.


    NOTICE:
    Make sure not to damage the bolt threads when installing the
    power steering pump to the air compressor.

    4. Install the two bolts attaching the power steering pump to the air compressor. Torque to
    40 N·m (30 lb·ft).
    ADDITIONAL SERVICE INFORMATION
    Additional service information is available in the Detroit Diesel EPA07 MBE 4000 Service Manual
    (DDC-SVC-MAN-0026). The next revision to this manual will include the revised information.

    Detroit Diesel®, DDC® and the spinning arrows design are registered trademarks of Detroit Diesel Corporation.
    © Copyright 2008 Detroit Diesel Corporation. All rights reserved. Printed in U.S.A.

    You might also like