How to Assemble and Use the Supplement Structure of the AKARI Origami unit

AKARI Origami Origami lampshade

"Celes"

Assembly time for the LED stand : Approximately 30 minutes Tri-color RGB LED
Parts in the Kit
Cover Attachment receiver
Origami lampshade "Checkered
Switch Lantern"
cover

Base unit (top)

Dials (3) Color adjuster dials
Screws (9)
Cover
(If you remove the cover, you can
access a pin connector for
linking to the "Japanino")
LED Switch
support column
Attachment for the
Celes ■ Attaching the circuit boards to the base unit 3. Attach the circuit boards to the base unit (top)

Screws
1. Attach the dials to the circuit boards Attach the large and small circuit
boards to the base unit (top) with
Attach the three dials to the volume shafts on the two circuit boards. Orient the screws using the position of the
Base unit (bottom) dials with the jagged sides up as shown in the diagram, and push them onto the switch on the large circuit board as a
posts all the way to the bottom. Circuit
guide for positioning the circuit board
boards. Slide the circuit boards in at Dial
an angle so that the dials protrude out
Dial through the slits in the base unit (top). Slit
Insert the switch cover at this time, as
well.
Volume shafts Base unit
(top)

Pass the LED connector through the

Origami paper Dials Screws hole in the center of the base unit
For the Checkered Lantern: 6 sheets (top).
For the Celes: 10 sheets with 3 pre-scored strips per sheet (cleanly cut the
strips apart using a utility knife or other cutting tool)
Attachment for the
Circuit board Checkered Lantern Circuit LED
* TANT N-8 paper is used for the origami paper here.
Volume shafts board connector
* The origami paper is included in the case with the parts shown at left. Take care to
ensure that you do not accidentally throw the paper away.
Dial

Things you will need Circuit

boards

A Phillips screwdriver, a utility knife, three AA batteries Slit

Screws
2. Connect the connector from the battery box to the
circuit board Dial
Materials used in this kit
Base unit, attachments, dials, cover, switch cover, LED stand, and support column stand Insert the battery connector coming out from the battery box on the base unit Switch
(white): ABS (bottom) into the battery connector receptacle on the circuit board.
Attachment receiver (white): POM Switch cover Base unit
Support column (white): PS (top)
Screws: Iron (chromium-plated) Base unit (bottom)
Battery contacts: Iron (nickel-plated)

Slit
Battery connector Line the switch up with this
part here.

Battery connector
receptacle Attach the switch cover to the black switch cap from
above at an angle as shown in the picture. If you find it
difficult to attach the cover, loosen the screws on the
circuit board and move the circuit board back before
attaching.

1 Otona no Kagaku 2
 R

■ Assembling the Base Unit 4. Attach the LED support column to the base unit ■ Turning the LED ON Auto mode A
G
(top) You can set it to this mode by pressing the switch twice starting with
1. Place the cover on the base unit (bottom) Turn the switch on the base unit ON the switch in the Switch OFF position. Each color in the RGB LED will
Push the LED connector part into the center of the base unit, and
Slide the cover into the slot on the base unit (bottom) to attach it. The switch on the AKARI Origami unit is programmed to cycle cycle through getting darker and brighter at different timing patterns.
insert the support column into the hole on the base unit. Line up B
through to the next operation in the sequence given each time the The timing patterns are as shown below, but the LED colors will roughly
the notch on the hole with the protrusion on the support column button is pressed. Each of the modes will be described below. appear to change at random. 30 60
to insert, and then continue to turn the support column （秒）
clockwise until it clicks into place.
Changes from brighter to darker over a cycle lasting approx. 20 sec.
Switch Manual Auto mode Auto mode Switch
ON mode A B OFF R

* The power will turn OFF automatically one hour after the switch was last
Changes from brighter to darker over a cycle lasting approx. 28 sec.
pressed.
G
Be sure to Manual mode
check the orientation of
In this mode, you can set the color to whatever you want by turning the Changes from brighter to darker over a cycle lasting approx. 48 sec.
the cover.
dials. Each of the dials is positioned from the switch as shown in the picture
* Do not attach the cover if planning to link the AKARI Origami to the "Japanino", below. Each dial is set up so that the light will get brighter when the dial is B
Slowly and
the supplement from Vol. 27 of the magazine.
carefully LED support turned clockwise as seen from above. Adjust the dials to produce the color 30 60
push the column you want. （秒）
(sec.)
2. Fit the base unit (top) and the base unit (bottom) cable into Click Auto mode B
the base unit.
together You can set it to this mode by pressing the switch three times starting with the
switch in the Switch OFF position. Each color in the RGB LED will change
Place the base unit (bottom) onto the base unit (top) while lining the Goes out Gets brighter between bright and dark in order over equally long cycles. With this mode, you
position for the switch up with the switch on the base unit (top). Screw Base
can enjoy sharply defined color changes along with the blending of two colors
unit
down the base unit (bottom) plate using the three holes in the battery box, GREEN (G) that appears during the transitions from one distinct RGB color to the next.
being careful not to let any wires get caught in the areas screwed down.

Off Off Off

Base unit (bottom) Screws

Completed R
Gets brighter and brighter until it reaches the maximum brightness and then
Gets brighter Goes out starts to get darker and darker.

RED (R) BLUE (B) G

Attachment receiver

You can change the

amount of support Goes Switch Gets B
column visible below the out brighter
30 60
lampshade by moving
（秒）
(sec.)
this up and down.
Check to make sure that
the LED connector has
been pulled outside of the Q: The LED will not light up even though the power A: The connector terminal connections may be bad. Unplug and plug the

Q＆A
Base unit connector several times and try again.
base unit. is ON. R
(top) A: Confirm that the batteries are new and that they
have been inserted in the correct direction. Check to Q: The battery box gets hot.
Switch make sure that the connector on the LED support A: Remove the battery immediately, and then contact us using the contact
column and the battery connector have been securely information given below.
fastened in place. Also make sure that the wires have not gotten caught G
in the screws and cut. Q: I couldn't find any origami paper included with the supplement.
A: The origami paper is slipped into the bottom of the Styrofoam tray when
Q: The light suddenly turns off unexpectedly. the kit is packaged. Double check the contents of the cardboard box
A: In order to conserve energy, there is an Auto OFF function that works to B again.
turn off power automatically one hour after the last operation has been
made. Press the switch button again to turn the power back on. Q: The switch is hard to press. 30 60
3. Attach the LED connector to the LED support A: Using the instructions given on the lower right of page 2, adjust the
（秒）

column Q: The brightness levels do not change when the dials are turned. position of the circuit board and reinsert the switch cover.
A: The unit may be in Auto mode. Press the switch button repeatedly until
Attach the LED connector from the hole on the base unit to the the unit turns off, and then press it just once more to turn it back on. The
connector on the LED support column. unit will be in Manual mode, which allows you to adjust the brightness
For information on how to make and levels.
attach an origami lampshade, go to
Q: Dials are hard to turn.
page 5 of this instruction booklet. A: The base unit (top) and/or LED cable may be interfering with the dial(s).
Remove the base unit (bottom) to check.
Connector on the LED LED connector
support column Q: Screws are hard to turn.
A: If you find that any screws are hard to turn, first try screwing in the screws
alone without trying to attach anything in order to prime the screw
holes before assembling. Try to use a screwdriver with a secure bit (end).

Q: The LED lighting is unstable.

3 Otona no Kagaku 4
 How to Assemble and Use the Supplement ■ Putting the units together
Hand 1. Slide a "hand" on

How to Make an Origami Lampshade

one unit into a "gap"
on another unit so that
they fit together to
combine the two units. The two units should look like the diagrams when put 2.Add a third unit to the assembly in the
Two different types of paper are included with this supplement for making lampshades for the AKARI Origami unit. You can make both together. same way.
the Checkered Lantern and the Celes and use each for a different location or type of situation. We've also included instructions on how
Hand
to make another type of lampshade, although we did not provide any paper for this one. Please select some paper that you like and try
making this one, too.
Gap

The Checkered Lantern Valley fold

(fold over)
Mountain fold (fold
under)
Time to complete: 30 min. ~ 1 hr.
As seen from the front As seen from the side
Gap
This lampshade was named the Checkered
Lantern due to the fact that a checkered How to fold one unit
pattern emerges when the finished 4. Rest the final unit on the top of
lampshade is attached and the LED is turned This side is the Turn the the assembly, and slide the "hands"
back side of the paper over. from the unit assembly into the
on. You will use the set of six square sheets
paper. The fold open "gaps" on the final unit.
of paper included in the supplement to lines are raised
make this lampshade. on this side.
The paper comes with pre-inserted fold
lines, so just fold the paper along those lines.
Use the side with indented fold lines as the
front side of the paper. The colored side of
paper shown in the diagrams is the front
5. Grasp one of the exposed
side. "hands" with your fingers and curve
1.Take two opposite corners and 2 it inward as shown in the picture
fold them in to the center. below.
3 3. Add a fourth unit on the front side.
Add a fifth unit on the other side in the
same way.

Turn the paper

over.

As seen from the top

■Attaching the assembled
lampshade to the LED stand

6 5. Open the two folded 4

corners.
If you are not able to get the unit
put together easily, apply glue to
each "hand" that you insert into a
7.Fold as shown while taking
10. Fold according to the "gap" to assemble.
care not to let fold lines in
inserted fold lines.
overlapping parts get
crooked. Push the attachment into one of the indentations
in the completed lampshade at whichever

6. Push the curved "hand"

Finished triangle you want until it gets caught on the end.
Be careful not to push the attachment into the
inside of the lampshade.
into the "gap."
11.Fold the other side in
the same way.
Attachment receiver

Unit completed
Make a total of six of
these units.
8.Open.

12

Insert the LED support column into the hole on

the attachment, and push it in up to the
7. Do the same for the other
attachment receiver. Then, turn the support
9 Insert a crease in the exposed "hands."
column clockwise into the base unit.
opposite side as well.
13.Open halfway.
5 Otona no Kagaku 6
 Celes
This lampshade was named Celes from the word Celestial because it glitters brightly like 7. Add in two additional units (for a total of ten
Valley fold
the stars in the sphere. You will use thirty strips measuring 28 cm 4.5 cm (1.1 in. 0.17 in.) Putting together the units) to each of the partially formed stars as
(fold over)
Mountain fold (fold cut from the ten sheets of paper included in the supplement to make this lampshade. five stars for the first line shown in the diagram to complete the five stars
Hand for the first line.
under) The paper comes with pre-inserted fold lines, so just fold the paper along those lines.
Use the side with indented fold lines as the front side of the paper. The colored side of
paper shown in the diagrams is the front side.
Pocket Pocket Complete this
Time to complete: 1 hr. ~ 2 hrs. step for all
five stars

■ How to fold one unit Each sheet of the paper for this lampshade includes three attached strips.
Please cut the three strips apart cleanly using a utility knife or other cutting tool before
starting the origami folds. ❺
This side is ❶
the back side
of the paper.
Unit completed
The fold lines
are raised. Hand
❷

❹
Pocket
Hand
Hand ❸
Pocket
5. Add five more units with each unit added as
shown in the diagram so as to connect each
6. After adding in the five units, you should Putting together the five stars for the
end up with five partial star shapes ( ❶ – ❺ ),
set of two neighboring arms together of the
each with three of the five points of a second line
five arms projecting out from the star.
completed star, for an overall shallow dish-like
3. Fold each big 4. Fold only each of 6. Unfold the folded Fold all thirty of the strips shape. The above picture was taken from the
back side of the assembled shape. Complete this ❶
triangle in half. the two small 5. Fold each in to sections back into the big of paper in the same way.
triangles in front in the opposite triangles shown in . step
half. sides. for all five stars
1. Fold the top and 2. Fold at each of the fold lines ❷
bottom ends into shown in the drawing to create
triangles. two big triangles. ❷ ❸
❶

■Putting the units together Structural diagram for the Celes

Complete this
step
At first glance, the Celes appears to be fairly for all five stars

1.Line up the mountain folds and complicated, but it actually has the simple structure as 8. Combine two arms projecting out from one
Putting together the star Pocket valley folds on a hand with those shown in the diagram. First, you need to create the star with those of neighboring stars ( ❶ and ❷ ,
first star for the bottom, then the five stars for the first ❸ and ❹ , and so on) to create five partial star
for the bottom on a pocket, and slide the hand ❸
all the way into the pocket so line on top of that, and then the five stars for the assemblies. Once you've completed this step,
Hand you should have five partial star shapes with two
that they fit together smoothly. second line on top of the first one. ❺
Finally, you just need to put together the very last star points each.
for the top to complete the lampshade. ❹

■ Attaching the assembled

The star for the top 10. Add in a total of five more units, one at a 9. At this point, there should be five
time, so as to connect together neighboring unattached arms ( ❶ – ❺ ) sticking out lampshade to the LED stand
Once you've slid a The five stars in the five star assemblies. Once you've from the assembly as seen from the
hand into a stars completed this step, you should have five back side.
pocket, go back for the partial star shapes with four points each.
and redo the second line
creases on each The
again to reinforce. five stars
2. Insert in the for the
same way as first line
with the first Putting together the star for the top
one.

The star for the bottom

Attach the attachment at a place where three stars intersect.

You may find it easier to insert the attachment if you cut out
a hole in the unit where you plan to insert it that is big
enough to fit it into using a utility knife or other cutting tool.

Finished Attachment receiver

The fifth 11.Add additional units to the [Diagram of lampshade before

unit partially completed stars in completion] While completing
order to complete each five- assembly of the stars for the
pointed star. The five second line, use the unattached
unattached arms here will be arms to put together the star for
3. Insert the fourth and fifth units as combined together to form the top of the lampshade. This
shown in the diagram. the final star for the top of the picture shows completion of Insert the LED support column into the hole on
lampshade. three of the points on the final the attachment, and push it in up to the
You may find it easier to insert the fifth
star. attachment receiver. Then, turn the support
unit if you open the pocket up and then
column clockwise into the base unit.
refold it so as to cover the last hand, as 4. This star shape formed using five different units is the
shown in the picture. base structure for this lampshade.

7 Otona no Kagaku 8
 Earthen
This lampshade was named Earthen because the pattern that emerges 14.Fold in toward the 15.Fold half only
Valley fold back toward the
when the LED is lit up resembles earthenware. No paper is provided for this center.
(fold over) other side.
Mountain fold (fold project, so please get six sheets of square paper such as regular origami
under) paper ready if you intend to try making this lampshade. We recommended
that you use paper that is around 15 cm 15 cm (5.9 in. 5.9 in.) because it will
be easier to make with paper around that size.
Time to complete: 1 hr. .~ 1 hr. and 30 min.

■ How to fold one unit

3. Fold two
opposite corners in 16.Repeat steps
toward the center. (12) to (15) to fold the
opposite side.
Unit completed Make a total of six of these
units.

17.Open as
Unit as seen from shown.
the front side.
Hand Hand

1. Fold the paper in half to insert a 2. Fold in half the other way to insert a Pocket
vertical fold line. horizontal fold line. 4. Fold the paper in
half in such a way
that the folded
parts are tucked
inside.
Hand Hand

Pocket Unit as seen from

the back side.

☆ ☆ ■Putting the units together

5. Fold the two sheets together as
shown in the diagram to insert a
crease line. ☆ ☆
Insert each hand into a pocket.
12.With the paper opened up as shown
in the diagram, you can see that there
is an indentation in the center of the ☆ ☆ You can make it easier to put the units
6. Fold using an inside reverse fold. paper (in the circled part). together and achieve a more polished
Push on this section from the back so finished product if you apply glue to
that it protrudes out, and then pull the the back side of the paper at the Hand Hand Hand Hand
paper in along the fold lines. portions marked with a ☆ in the
picture.

■ Attaching the assembled

lampshade to the LED stand
Hand Hand
11.Open as shown. Hand Hand

7. Fold using an inside

reverse fold.

When the light is turned on, a complicated

13.Fold in toward pattern will emerge as shown in the
the opposite side. picture.
The center part will
protrude out as can
be seen in the
picture below.

8. Do the same on the right

side. 10. Fold as shown in
the diagram. Do the
same on the back
side. Use the attachment for the Checkered Lantern. Cut away one
edge of the protrusions in the Earthen lampshade to insert
the attachment into the hole formed. Affix the Earthen
lampshade and the attachment to each other using
In the above picture, paper with a darker color on one side was used to cellophane tape or the like, and then attach the assembly to
9. Fold back the overlapping make it easier to tell between the front and back sides of the paper; the LED support column.
sections. Do the same on the
back side.
however, in actuality, you'll achieve a better effect with the lighting
using paper that is either white or a light color on one side. Finished
9 Otona no Kagaku 10