Deh 1100
Deh 1100
DEH-1100
DEH-11 X1M/UC
X1M/UC
- This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. SAFETY INFORMATION ............................................2 7. GENERAL INFORMATION .......................................45
2. EXPLODED VIEWS AND PARTS LIST .......................2 7.1 DIAGNOSIS ........................................................45
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8 7.1.1 TEST MODE ..............................................45
4. PCB CONNECTION DIAGRAM ................................26 7.1.2 DISASSEMBLY .........................................48
5. ELECTRICAL PARTS LIST ........................................36 7.2 PARTS .................................................................52
6. ADJUSTMENT..........................................................41 7.2.1 IC................................................................52
7.2.2 DISPLAY ....................................................58
7.3 OPERATIONAL FLOW CHART ...........................59
8. OPERATIONS AND SPECIFICATIONS.....................60
1. SAFETY INFORMATION
CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of
California to cause cancer, birth defects or other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
8
2
9 11
7
14
1
15
10
13
12
2
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDE6124 11-1 Polyethylene Bag CEG1116
2 Spring CBH1650 11-2 Owner’s Manual CRD3133
3 Screw CBA1002 11-3 Installation Manual CRD3134
* 4 Polyethylene Bag CEG-127 * 11-4 Card ARY1048
5 Screw CRZ50P090FMC 12 Carton See Contrast table(2)
Part No.
Mark No. Symbol and Description DEH-1100/X1M/UC DEH-11/X1M/UC
12 Carton CHG3953 CHG3954
13 Contain Box CHL3953 CHL3954
3
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
2.2 EXTERIOR
4
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
Part No.
Mark No. Symbol and Description DEH-1100/X1M/UC DEH-11/X1M/UC
43 Keyboard Unit CWM6783 CWM6782
50 Grille Unit CXB4619 CXB4620
5
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
6
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
Mark No. Description Part No. Mark No. Description Part No.
1 Control Unit CWX2411 46 •••••
2 Connector(CN802) CKS2192 47 Ball CNR1189
3 Connector(CN801) CKS2193 48 Belt CNT1086
4 Connector(CN701) CKS2773 49 Roller CNV4509
5 Connector(CN101) CKS3486 50 Arm CNV6037
7
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-1100,11
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A TUNER AMP ASSY
A
B FM/AM TUNER UNIT
FM FRONT END FM/AM 1ST IF 10.7MHz
ANTENNA Q3 T51 Q51 CF51 CF52 CF53 FM MPX
CN402
25 24
27
32 19
IC 2 PM4008A 6
38 39 42 44 46 63 34 33 41 44 11 12 13 46
69
ANT1 TV
ANT2 TV 22
RF TV
70
54 COMP
MIXER.IF AMP DET 21
IC 1 78 LDET
18
PML002A 65
71
35
Q201 Q204
33 32 45 55 57 CF202 61 74 75
28
EEPROM
AM RF 5 4
IC 3
AM 2ND IF 450kHz 6 BR9010FV 3
Q202
VDD
FMSD
DI/DO
VCC
CE2
CE1
NL1
NL2
CK
SL
25 22 10 14 12 15 16 13 2 3 4
Q411
PDIO
PCE2
CK
PCE1
PCK
SD
PD
LOCL
VCC VDD
18 TOP HOME
4
SPINDLE M S801
C MOTOR 12
SOP
HOME
11
CN801 SOM
14
1 COP
CARRIAGE M 13 COM 1 CDLOAD CDLOAD
MOTOR 2 FWD 6 19
10 28 CDEJET EJET
LOP REV 5 20
9 21 CONT CONT
LOM MUTE 11 14
LOADING 3
MOTOR
M
4
CN802
EJTSNS EJTD
3 22 3
1 DSCSNS DINC
23 2
CLAMP CLAMP
VD 21 4
SELECT Q981
SENSE D803 D802 D801 VD
S802 VD 24 1 B.U
2 CLAMP
DISC SENSE +5V REGULATOR
4 IC 701 2
E PHOTO UNIT(S8) VDD
BA05SFP
IN
Q982
1 CD5VON CD5VON
7 18
VDCONT
8
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-1100,11
CN301
REAR L CH
Q346
SYSTEM
CONTROLLER
IC 601(1/2)
PE5091A
6
SD
76
SL
14
TUNPCE
13
TUNPCK
48
TUNPCE2
12
TUNPDO
PDIO 11
TUNPDI VST
VCK Q353
67 VDT
LOCL
Q903
BACKUP
VDD B.U B.U
FUSE
10A B
2 BACK UP
GND
1 GND
2 VST/ VCK/ VDT POWER AMP
IN1
Q351 MUTE
Q902
asens ACC 4 ACC
bsens
B.U
63
ASENS
Q901
64
BSENS
SYSTEM
CONTROLLER
IC 601(2/2) C
PE5091A
Q942 Q941
42 B.REMOTE
SYSPW B.REMOTE
31 CDLOAD 5
34 CDEJECT
23 CONT
44
80 MUTE
EJTSNS
79
DSCSNS
C KEYBOARD UNIT
27
CLAMP
CN601 CN1801
8 20
KYDT 3 3 KYDT
22 9 LCD
VDCONT 4 4 18
DPDT DPDT
RESET
60 1 IC 602 2
RESET VDD
S–80834ANY
VDD
50
5 5 VDD
10 VLCD
41
SWVDD Q650
35
CD5VON
LCD DRIVER
IC 1801 D
PD6293A
KEY MATRIX
22 23
X1801
9
Downloaded from www.Manualslib.com 5manuals search engine 6 7 8
1 2 3 4
DEH-1100,11
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS
LIST”.
A-a
Large size
A-a A-b
SCH diagram
CD:+4.
FM(100%):-19
AM (30%):-30
272
183
162
DSP-201M-S00B
C499
162
103
183
272
104
4.194304MHz
CSS1023
150 150
682
R
822
433
SYSTEM CONTROLLER
R699 0R0
C
KEYBOARD 104
UNIT
D
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and For resistors and capacitors in the circuit diagrams, their resistance values or
discrete resistors. capacitance values are expressed in codes:
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and Ex. *Resistors
discrete capacitors. Code Practical value
The > mark found on some component parts indicates 123 12k ohms
the importance of the safety factor of the part. 103 10k ohms
Therefore, when replacing, be sure to use parts of
identical designation. *Capacitors
Code Practical value
A
103 0.01µF
101/10 100µF/10V
10
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-1100,11
A-b A
CD:+10.1dBs
FM(100%):+3.5dBs
AM (30%):-7dBs
AA TUNER AMP ASSY
4.1dBs
9.5dBs
0dBs
SOURCE SELECTOR/
E.VOL
POWER AMP
332/16
CD:+10.1dBs
FM(100%):+3.5dBs
AM (30%):-7dBs
B
CD:+36.1dBs
FM(100%):+29.5dBs
AM (30%):+19dBs
>
CEK1136
600µH
Reset
C
(B2)
CD MECHANISM MODULE
VD REGULATOR
CD:+4.1dBs
D
D
D
A
C
A-a A-b
12
1
1
A-a
DEH-1100,11
CD:+4.1dBs
FM(100%):-19.5dBs
AM (30%):-30dBs
272
183
162
SOURCE
C499
E.VOL
162
103
183
DSP-201M-S00B
272
3
3
4
4
104
4.194304MHz
CSS1023
150 150
150 150
682
Reset
822
5
433
2
6
R699 0R0
C
104
KEYBOARD
UNIT
7
7
NOTE :
Symbol indicates a resistor.
CD MECHANISM MODULE
No differentiation is made between chip resistors and For resistors and capacitors in the circuit diagrams, their resistance values or
discrete resistors. capacitance values are expressed in codes:
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and
D
Ex. *Resistors
discrete capacitors. Code Practical value
The > mark found on some component parts indicates 123 12k ohms
the importance of the safety factor of the part. 103 10k ohms
Therefore, when replacing, be sure to use parts of
identical designation. *Capacitors
Code Practical value
103 0.01µF
101/10 100µF/10V
8
8
A-a 13
DEH-1100,11
A-a A-b
B
C
A
D
B
D
A
14
A-a A-b
1
1
A-b
DEH-1100,11
CD:+10.1dBs
FM(100%):+3.5dBs
AM (30%):-7dBs
SOURCE SELECTOR/
E.VOL
POWER AMP
3
3
332/16
CD:+10.1dBs
FM(100%):+3.5dBs
AM (30%):-7dBs
1
CD:+36.1dBs
FM(100%):+29.5dBs
AM (30%):+19dBs
4
4
>
CEK1136
600µH
5 6 7 8
DEH-1100,11
A-a A-b
A
600µH
(B2)
C
VD REGULATOR
CD:+4.1dBs
D
Reset
CD MECHANISM MODULE
A-b 15
2
A A
B FM/AM TUNER UNIT
B
KV1410(23)
C
DAN217U
DAN217U
16 B
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-1100,11
KV1410(23)
C KEYBOARD UNIT
PD6293A
LCD DRIVER,
KEY CONTROLLER
CAW1560
18
1
C
Downloaded from www.Manualslib.com manuals search engine
2 3 4
5 6 7 8
DEH-1100,11
LOUD
CN601
B
CLK LOCAL
A
BSM
DEH-1100/X1M/UC DEH-11/X1M/UC
IL1801-1804 CEL1547(14V 40mA) CEL1638(14V 40mA)
A
D CONTROL UNIT
PICKUP UNIT
(SERVICE)(P8)
CN101
RF-AMP, SE
E PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR
M3 CXB2562
CARRIAGE MOTOR
M1 CXB2190
D LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
20
1
D E
Downloaded from www.Manualslib.com manuals search engine
2
BA05SFP
5V REGULATOR
3 4
5 6 7 8
DEH-1100,11
SWITCHES:
CONTROL UNIT
S801 : HOME SWITCH.....ON-OFF
S802 : CLAMP SWITCH....ON-OFF
The underlined indicates the switch position.
CN701
CN605
A
Note:1. The encircled numbers denote measuring pointes in the circuit diagram.
2. Reference voltage
REFO:2.5V
- Waveforms
1 RFI 0.5V/div. 0.5µs/div. 1 CH1: RFI 1V/div. 0.5ms/div. 1 CH1: RFI 1V/div. 0.5ms/div.
Normal mode: play 2 CH2: MIRR 5V/div. 2 CH2: MIRR 5V/div.
Test mode: Tracking open Normal mode: The defect part
passes 800µm
REFO →
REFO →
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO → REFO →
GND →
REFO → REFO →
REFO →
22
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO →
REFO →
GND →
REFO →
REFO → REFO →
REFO →
GND → GND →
GND →
REFO → REFO →
GND → GND →
23
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
REFO →
REFO → REFO →
24
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
25
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-1100,11
A
4.1 TUNER AMP ASSY
NOTE FOR PCB DIAGRAMS
1. The parts mounted on this PCB
include all necessary parts for
several destination.
For further information for
respective destinations, be sure
to check with the schematic dia-
gram.
2. Viewpoint of PCB diagrams
Connector Capacitor
SIDE A
B
C
CN701
D
26 A
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
C CN1801
5 6 7 8
DEH-1100,11
A
SIDE A
28 A
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-1100,11
SIDE B
SIDE A
A
B
C
FM/AM TUNER UNIT
D
B
30
1
B
Downloaded from www.Manualslib.com manuals search engine
2 3 4
1 2 3 4
DEH-1100,11
SIDE B
C
FM/AM TUNER UNIT
D
B
BAND
AUDIO
A
EJECT
]
'
'
BSM
[
CLOCK
LOCAL
B
6
5
4
C
3
2
SOURCE/OFF
KEYBOARD UNIT
1
LOUD
D
C
+
32 C
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
1 2 3 4
DEH-1100,11
SIDE B
A
B
CN601
A
C
KEYBOARD UNIT
D
C
D
A
34
D CONTROL UNIT
1
1
PICKUP UNIT(SERVICE)(P8)
DEH-1100,11
M1 CARRIAGE MOTOR
M3 SPINDLE MOTOR
3
3
4
4
3
2 D CN802
1
SIDE A
1 2 3 4
DEH-1100,11
SIDE B
CLAMP
B
CONTROL UNIT
C
D
36
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
R 651 RS1/8S222J C 363 CEJA100M16
R 655 RS1/10S103J C 364 CKSYB474K16
R 656 RS1/10S103J C 365 CKSQYB474K16
R 657 RD1/4PU102J C 366 CKSYB474K16
R 658 RD1/4PU102J C 367 CKSQYB474K16
37
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
L 201 Inductor LCTB330K1608 R 904 RS1/16S473J
L 202 Inductor CTF1287 R 907 RS1/16S103J
L 203 Inductor LCTA121J3225 R 908 RS1/16S681J
L 901 Coil CTC1154 R 909 RS1/16S473J
L 902 Inductor LCTA3R3J3225 R 914 RS1/16S562J
38
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
C 211 CKSRYB103K50 Unit Number : CWX2411
C
C
212
215
CCSRCH101J50
CKSRYB223K25
D Unit Name : Control Unit
C 216 CKSQYB334K16
C 217 CKSRYB103K50 MISCELLANEOUS
39
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
C 301 CEV101M10
C 603 CCSQSL152J50
C 604 CCSQSL152J50
C 702 10µF/10V CCH1349
C 703 CKSQYB334K16
Unit Number :
E Unit Name : Photo Unit(S8)
Q 1 Photo-transistor CPT230SX-TU
Q 2 Photo-transistor CPT230SX-TU
40
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions 2) Test Mode
• This unit uses a single power supply (+5V) for the reg- This mode is used for adjusting the CD mechanism
ulator. The signal reference potential, therefore, is module of the device.
connected to REFO(approx. 2.5V) instead of GND.
If REFO and GND are connected to each other by mis- • Test mode starting procedure
take during adjustments, not only will it be impossi- Reset while pressing the 4 and 6 keys together.
ble to measure the potential correctly, but the servo
will malfunction and a severe shock will be applied to • Test mode cancellation
the pick-up. To avoid this, take special note of the fol- Switch ACC, back-up OFF.
lowing.
Do not connect the negative probe of the measuring • After pressing the EJECT key, do not press any other
equipment to REFO and GND together. It is especially key until the disk is completely ejected.
important not to connect the channel 1 negative
probe of the oscilloscope to REFO with the channel 2 • If the ] or [ key is pressed while focus search is in
negative probe connected to GND. progress, immediately turn the power off (otherwise
Since the frame of the measuring instrument is usual- the actuator may be damaged due to adhesion of the
ly at the same potential as the negative probe, change lenses).
the frame of the measuring instrument to floating sta-
tus. • Jump operation of TRs other than 100TR continues
If by accident REFO comes in contact with GND, after releasing the key. CRG move and 100TR jump
immediately switch the regulator or power OFF. operations are brought into the “Tracking close” sta-
tus when the key is released.
• Always make sure the regulator is OFF when connect-
ing and disconnecting the various filters and wiring • Powering Off/On resets the jump mode to “1TR”, and
required for measurements. the automatic adjustment value to the initial value.
41
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
- Flow Chart
4 6
Test Mode In
Reset
Select CD SOURCE
BAND 3 6
Power ON
(Adjustment for T.Offset)
Power ON
TRK MIN SEC
(Not adjustment for T.Offset)
Display 00 00 00 TRK MIN SEC
Display 99 99 99
Power OFF
BAND 3 6 1 ] [ 2
Display
91 91 91 Display 0x 0x 0x 00 00 00 00 00 00 00 00 00
or or or
TRK MIN SEC TRK MIN SEC TRK MIN SEC
99 99 99 99 99 99 99 99 99
Power OFF
BAND 1 6 3 ] [ 2
T.Close and
F,T AGC and T. Close and RF AGC Coefficient Display/ CRG+ CRG- T.Balance
RF AGC and Fit Servo Rough Servo and RF AGC Adjustment
Fit Servo TRK MIN SEC TRK MIN SEC
Display 8x 8x 8x 8x 8x 8x
or or
TRK MIN SEC TRK MIN SEC
9x 9x 9x 9x 9x 9x
Tracking
Power OFF Open
BAND 1 3 6 ] [ 2
*4 *5 *6 CRG-/TR Jump- *6
F, T, RF AGC/ F, T AGC and CRG/TR Jump NO. CRG+/TR Jump+ *7
F.Bias Display Select RF AGC Select TRK MIN SEC
Power OFF
Display
8x 8x 8x
or
BAND TRK MIN SEC
2
9x 9x 9x
Tracking
Open
TRK MIN SEC
Display 8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
42
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFOUT
• Disc • ABEX TCD-784
• Mode • TEST MODE
CONTROL UNIT
E
F L.P.F.
Xch Ych
E 100kΩ
Oscilloscope
REFO 390pF
F 100kΩ
390pF
REFO REFO
L.P.F.
• Checking Procedure
1. In test mode, load the disc and switch the 5V regulator on.
2. Using the ] and [ buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-
ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-
ence is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-
age angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
43
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
0° 30°
45° 60°
75° 90°
44
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the
error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the
users and also for facilitating trouble analysis and repair work in servicing.
45
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
46
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
47
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
7.1.2 DISASSEMBLY
- Removing the Upper Case (not shown)
Fig.1
CD Mechanism Module
Cover
- Removing the Tuner Amp Assy
Fig.2
Fig.3
Tuner Amp Assy
48
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
B A
Arm A
Arm
B A
49
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
A A
50
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
A
A
Loading Motor
Pickup Unit
Shaft
51
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
7.2 PARTS
7.2.1 IC
- Pin Functions(PE5091A)
Pin No. Pin Name I/O Format Function and Operation
1 MODEL1 I Model select input
2 NL1 I Noise level input
3 NL2DT I Noise level input 2
4 AVSS A/D GND
5 ST I Stereo input
6 SD I SD signal input
7 AREF1 (D/A converter standard voltage)
8 KYDT I Key data input
9 DPDT O C Key data output
10 SDBW I SDBW input
11 TUNPDI I PLL IC data input
12 TUNPDO O C PLL IC data output
13 TUNPCK O C PLL IC clock output
14 TUNPCE O C PLL IC chip enable output
15 NC Not used
16 XSI I C LSI data input
17 XSO O C LSI data output
18 XSCK O C LSI clock output
19 DRST O C RDS decoder reset output
20 ADPW O C A/D converter power output
21 NC Not used
22 VDCONT O C VD power control output
23 CONT O C Servo driver power control output
24 XAO O C CD LSI data discernment control signal output
25 XRST O C CD LSI reset output
26 XSTB O C CD LSI strobe output
27 CLAMP I Disc clamp sense input
28 MIRR I Mirror detection input
29 FOK I Focus OK signal input
30 LOCK I Spindle lock detector input
31 CDLOAD O C LOAD motor loading control output
32 TELIN I Cellular mute input
33 VSS GND
34 CDEJECT O LOAD motor eject control output
35 CD5VON O C CD +5V power supply control output
36–40 NC Not used
41 SWVDD O C Grille power supply control output
42 SYSPW O C System power supply control output
43 NC Not used
44 MUTE O C Mute output
45 PEE O C Beep tone output
46 LOCH O C LOCH output
47 RDS57K I 57kHzBP-OUT sense input
48 TUNPCE2 O C EEPROM chip enable output 2
49 NC Not used
50 VCK O C Clock output for electronic volume
51 VDT O C Data output for electronic volume
52 ANTPW O C Antenna power output
53 VST O C Strobe pulse output for electronic volume
54–57 DEQ4-1 O C Direct EQ data output 4-1
58, 59 NC Not used
60 RESET Reset
61, 62 NC Not used
63 ASENS I ACC power sense input
52
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
*PE5091A BR9010FV
80 61 NC 1 8 WC
1 60
21 40
SK 4 5 DI
S-80834ANY *PD6293A
33
48
32 49
17 64
16
1 2 3
OUT VDD VSS
53
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
SN761029DL
TONEout-R
BASS-C1-R
BASS-C2-R
REARout-R
FADERin-R
FRNTout-R
BASS-R-R
SWout-R
IN4(+)-R
LOUD-R
IN4(-)-R
TREB-R
VRin-R
ZCin-R
AGND
DATA
IN1-R
IN2-R
IN3-R
DVcc
VCC
STB
CLK
NC
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
Isolator
Volume, Treble Bass Fader
Loudness
Gain
Adjust
Gain
Adjust
Volume,
Loudness Treble Bass Fader Power A
Supply
Isolator
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
AVcc
IN1-L
IN2-L
IN3-L
IN4(+)-L
IN4(-)-L
AGND
SWout-L
ZCin-L
LOUD-L
VRin-L
TREB-L
BASS-C1-L
BASS-R-L
BASS-C2-L
TONEout-L
NC
FADERin-L
FRNTout-L
REARout-L
VREFin
AGND
DGND
Ct
54
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
55
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
1
1
26
21 100
80
50
40 76
61
51
75
41
60
56
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
BA5985FM
57
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
7.2.2 DISPLAY
- CAW1560
SEGMENT
COMMON
58
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
Power ON
VDD=5V
68pin
bsens
66pin
asens
65pin
dsens
63pin
L
ADPW←H
20pin
swvdd←L
41pin
300ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300msec, the oscillator
may be defective.
Source ON
YES
SYSPW←H
42pin
59
Downloaded from www.Manualslib.com manuals search engine
DEH-1100,11
LOCAL button
LOUD button CLOCK button AUDIO button
Buttons 1–6 BSM button
60
Downloaded from www.Manualslib.com manuals search engine
A TitleOperation
Basic (English) A Title (English)
Note:
• When no disc is set in this product, built-in CD player source will not change.
• When this product’s blue/white lead is connected to the car’s Auto-antenna relay control terminal,
Preset Number Indicator
the car’s Auto-antenna extends when this product’s source is switched ON. To retract the antenna, Band
switch the source OFF. Frequency Indicator FM1 = FM2
= FM3 =AM
2. Raise or lower the volume. Band Indicator
Preset Tuning
Hold for 1 second
• You can memorize broadcast stations in buttons 1 through 6
for easy, one-touch station recall.
Preset station recall 2 seconds or less
Broadcast station preset memory 2 seconds or more
Note:
• Up to 18 FM stations (6 in FM1, FM2 and FM3) and 6 AM stations can be stored
in memory.
• You can also use the 5 or ∞ buttons to recall broadcast stations memorized in
buttons 1 through 6.
61
DEH-1100,11
A TitleOperation
Basic (English) A TitleAdjustment
Audio (English)
62
Basic Operation of Built-in CD Player Entering the Audio Menu
With this Menu, you can adjust the sound quality.
Eject Note:
• After entering the Audio Menu, if you do not perform an operation within about 30 seconds, the
DEH-1100,11
Note:
• If a disc cannot be inserted fully or playback fails, make sure the recorded side is down.
Push the EJECT button and check the disc for damage before reinserting it.
• If a disc is inserted with the recorded side up, it will be ejected automatically after a few
moments.
• If the built-in CD player cannot operate properly, an error message (such as “ERROR-14”)
appears on the display.
A TitleAdjustment
Audio (English)
Note:
• FADER “0” is the proper setting when 2 speakers are in use.
63
DEH-1100,11
64
Connection Diagram
Perform these connections when using a different amp (sold separately).
Rear output
To system control terminal of
Fuse the power amp or Auto-antenna
Antenna jack relay control terminal.
(Max. 300 mA 12 V DC.)
Blue/white Power amp
(sold separately)
System remote control
Rear + + Rear
speaker speaker
≠ ≠
DEH-1100,11
8.2 SPECIFICATIONS
General CD player
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable) System .................................... Compact disc audio system
Grounding system ........................................ Negative type Usable discs .................................................. Compact disc
Max. current consumption ...................................... 10.0 A Signal format .................... Sampling frequency: 44.1 kHz
Dimensions Number of quantization bits: 16; linear
(DIN) (chassis) ...... 178 (W) × 50 (H) × 159 (D) mm Frequency characteristics .............. 5 – 20,000 Hz (±1 dB)
[7 (W) × 2 (H) × 6-1/4 (D) in] Signal-to-noise ratio ...... 94 dB (1 kHz) (IHF-A network)
(nose) ............ 188 (W) × 58 (H) × 19 (D) mm Dynamic range ............................................ 92 dB (1 kHz)
[7-3/8 (W) × 2-1/4 (H) × 3/4 (D) in] Number of channels ............................................ 2 (stereo)
(D) (chassis) ...... 178 (W) × 50 (H) × 164 (D) mm
[7 (W) × 2 (H) × 6-1/2 (D) in] FM tuner
(nose) ............ 170 (W) × 48 (H) × 14 (D) mm Frequency range .................................... 87.9 – 107.9 MHz
[6-3/4 (W) × 1-7/8 (H) × 1/2 (D) in] Usable sensitivity .................................................... 10 dBf
Weight ........................................................ 1.4 kg (3.1 lbs) (0.9 µV/75 Ω, mono, S/N: 30 dB)
50 dB quieting sensitivity .... 15 dBf (1.5 µV/75 Ω, mono)
Amplifier Signal-to-noise ratio ...................... 70 dB (IHF-A network)
Continuous power output is 17 W per channel min. into 4 Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)
ohms, both channels driven 50 to 15,000 Hz with no more Frequency response ...................... 30 – 15,000 Hz (±3 dB)
than 5% THD. Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
Maximum power output ...................................... 40 W × 4 Selectivity .................................................... 70 dB (2ACA)
Load impedance .......................... 4 Ω (4 – 8 Ω allowable) Three-signal intermodulation
Preout maximum output level/ (desired signal level) ........................................ 30 dBf
output impedance .................................... 2.2 V/1 kΩ (two undesired signal level: 100 dBf)
Tone controls
(Bass) .............................................. ±12 dB (100 Hz) AM tuner
(Treble) ............................................ ±12 dB (10 kHz) Frequency range ...................... 530 – 1,710 kHz (10 kHz)
Loudness contour ........ +10 dB (100 Hz), +7 dB (10 kHz) Usable sensitivity .............................. 18 µV (S/N: 20 dB)
(volume: –30 dB) Selectivity ................................................ 50 dB (±10 kHz)
Note:
• Specifications and the design are subject to possi-
ble modification without notice due to improve-
ments.
65
Downloaded from www.Manualslib.com manuals search engine