Instructions for use

Coffee machine

Index
GB
Installation 4
GB FR ES Positioning
Built-in installation
English,1 Français, 27 Espanol, 53 Ventilation
Centring and fixing
Electrical connection
Installing the power cable
Rating plate

Description of the appliance 6

Overall view
Control panel

Starting and using 7

The first time you switch on
Priming the water circuit
Regulating water hardness
Aqua Prima filter (where installed)
Installing the Aqua Prima filter
Additional information for correct use of the “Aqua
prima” filter (where installed)
Grinding regulation

Brewing 10
SBS System
Regulating the quantity of coffee per cup
Brewing coffee (1 cup)
Brewing coffee (2 cups)
Dispensing hot water
Brewing steaming/cappuccino

Maintenance and care 12

General cleaning
Descaling
Interrupting the descaling cycle

Programming 15
MENU command
Changing individual functions
Programmable functions
Factory settings

Display messages 23

Problems - causes - solutions 24

Precautions and recommendations 25

GB IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and/or injury to persons, including the following:

1 Read all instructions and information in this instruction book and any other literature included
in this carton referring to this product before operating or using this appliance.
2 Do not touch hot surfaces. Use handles or knobs.
3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or
appliance in water or other liquid.
4 Close supervision is necessary when any appliance is used by or near children.
5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or
taking off parts, and before cleaning the appliance.
6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions
or has been damaged in any way. Return appliance to the nearest authorized service centre
for examination, repair or adjustment.
7 The use of accessory attachments not recommended by the appliance manufacturer may
result in fire, electric shock or personal injury.
8 Do not use outdoors.
9 Do not let cord hang over edge of table or counter, or touch hot surfaces.
10 Do not place on or near a hot gas or electric burner, or in a heated oven.
11 Always turn appliance “OFF”, then plug cord into the wall outlet. To disconnect, turn switch to
“OFF”, then remove plug from wall outlet.
12 Do not use appliance for other then intended household use.
13 Use extreme caution when using hot steam.

SAVE THESE INSTRUCTIONS

2
 CAUTION GB

This appliance is for household use. Any servicing, other than cleaning and user maintenance,
should be performed by an authorized service centre. Do not immerse base in water. To reduce
the risk of fire or electric shock, do not disassemble the base. There are no user serviceable parts
inside. Repair should be done by authorized service personnel only.

1 Check voltage to be sure that the voltage indicated on the nameplate agrees with your
voltage.
2 Never use warm or hot water to fill the water tank. Use cold water only.
3 Keep your hands and the cord away from hot parts of the appliance during operation.
4 Never clean with scouring powders or hard implements. Simply use a soft cloth dampened
with water.
5 To avoid your coffee maker scaling up, use purified or bottled water.

INSTRUCTIONS FOR THE POWER SUPPLY

CORD

A A short power-supply cord is provided to reduce risks of getting tangled up or tripping over
a longer cord.
B Longer extension cords are available and may be used if care is exercised in their use.
C If a long extension cord is used:
1 the marked electrical rating of the extension cord should be at least as great as the electrical
rating of the appliance.
2 if the appliance is of the grounded type, the extension cord should be a grounding type
3 the cable does not hang from the table to avoid the risk of getting caught up in it.

3
 Installation

! Keep this booklet for consultation at any time. In the ! Once the appliance has been encased, there must
GB event of sale, transfer of the machine or of the owner be no contact possible with electrical parts. Declared
ensure that the booklet is kept with the machine so that consumption values shown on the rating plate are
the new owner is informed of the operating instructions measured on the basis of this type of installation.
and warnings.
Ventilation
! Read all instructions carefully: they contain important
information regarding installation, operation and safety. To ensure good ventilation, remove the rear panel of the
cabinet.
Positioning It is recommended to install the coffee machine so that
it is resting on a continuous surface with an opening of
! Packaging is not a toy for children and should at least 45 x 540 mm in the base.
be disposed of in accordance with regulations for
separated waste collection (see Precautions and Centring and fixing
recommendations).
To centre the coffee machine, position the shims
! Installation must be carried out in compliance with beneath the holes in the outer structure of the machine.
these instructions by professionally qualified personnel.
Incorrect installation may cause damage to persons, ! All shims must be attached so that they ensure perfect
animals and/or objects. stability of the machine.

Built-in installation To attach the shims to the cabinet proceed as follows:

To ensure the correct functioning of the appliance, the • remove the drip tray
cabinet must have the right characteristics: from the machine;

• the panels next to the coffee machine must be in

heat-resistant material;

• veneered wood cabinets should be joined using

glues resistant to 100°C and must be steam-
resistant;

• for all installations of built-in coffee machines

cabinets should have the following dimensions: • remove the lower
plastic protection;

�
���
��

�
���
��
�� �
�� ���
� ��
• fasten the 2 wood
��
��
� screws in the 2 holes
�
located to the rear of the
base.

��
�� ��
��� �
�

4
! All protective parts must be attached so that they Rating plate
cannot be removed without the aid of a tool. GB
• Nominal voltage
Next replace the protection and the drip tray. See plate on the appliance
• Power rating
Electrical connection
See plate on the appliance
! Coffee machines with three-pole power cable are • Power supply
regulated for alternating current, with voltage and See plate on the appliance
frequency shown on the rating plate attached to the • Shell material
appliance. Metal
• Dimensions (w x h x d) (mm)
! The installer is responsible for checking the correct 595 x 460 x 320
connection of components and observing safety
regulations. • Weight (kg)
23
Before connecting make sure that: • Cable length (mm)
• the socket is earthed and is compliant with statutory 1200
regulations: • Control panel
• the socket is able to withstand the maximum power Piezoelectric
load of the machine, shown on the rating plate;
• Water tank
• the supply voltage is within the values shown on the
Removable
rating plate;
• the socket is compatible with the appliance’s plug. • Water tank (l)
Otherwise replace the plug or the socket; do not use 1.75
extension leads or adaptors. • Coffee bean hopper capacity (g)
300 g coffee beans
! Once the appliance is installed, the electric cable and • Pump pressure (bars)
socket must be easy to reach. 15
• Boiler
! The power cable must not be subject to coiling or
2 - Stainless Steel - Aluminium
compression.
• Safety devices
! The cable must be checked regularly and replaced Boiler pressure safety valve
only by authorised technicians. Safety thermostat

! The company accepts no responsibility for non-

compliance with these regulations. Subject to engineering and manufacturing changes
due to technological developments.
Installing the power cable
The machine conforms to the European Directive
• Put the plug in the 89/336/EEC (Italian Legislative Decree 476 dated
tray socket on the rear 04/12/92) concerning electromagnetic compatibility.
of the machine

• Connect the power

cable to the mains

• Put the plug in the

power socket.

The position of the

power cable must be
such that no section of it is above room temperature
by more than 50°C.

5
 Description of the
appliance
Overall view
GB
Water tank Front control panel
Main switch
SBS
Coffee bean hopper
Hot water/steam spout

Grill

Tray full float

Grind regulation

Brew group Adjustable-height brew unit

Drip tray

Control panel DESCALING

key

žžžžžžžžžžžžžžžžžžž
žžžžžžžžžžžžžžžžžžž

PROGRAMMING/EXIT Select STEAM key

selection key
Select HOT WATER key
PAGE SCROLL Select ESPRESSO key
key Select REGULAR COFFEE key
SELECT/CONFIRM Select LONG COFFEE key
Key
Select DOUBLE COFFEE key

6
Starting and using

! Before starting the machine make sure the hoppers Rinse and fill the
contain the amount described in the manual. tank with fresh drinking GB
Prime the circuit immediately to prevent damage to the water.
machine.
Close the lid and
! After starting the machine, regulate water hardness. replace the tank in
That will allow you to keep your machine in perfect position.
order (see Programming).
! The machine requires
the tank to be filled
The first time you switch on even when the level
is still high. This
1. Open the front panel happens because the tank of the coffee machine has
by pressing firmly in the been preset to house the optional “water filter”, thus
centre requiring a minimum level of water in the tank for
filtering to be performed

! Always use fresh, non-sparkling water to fill the tank.

Hot water or any other liquid may damage the tank
and/or the machine. Do
not switch the machine
on without water: make
sure there is enough
water in the tank.
2. Remove only part of
the bean hopper.
The main switch is in
the “O” position. To
switch on, press the key
in the “I” position.

Close the front panel by pressing firmly in the centre.

The machine begins to heat up and the display shows:

3. Pour coffee beans RINSING

into the hopper being WARMING UP...
careful not to add too
many. When the right temperature is reached, the machine
Close the lid and repla- goes through a rinsing cycle.
ce the hopper inside the
machine. RINSING

The machine dispenses water from the brew unit as it

rinses the internal circuits.
4. Remove the water
tank fully from the After rinsing, the machine returns to normal operating
machine. conditions. The display shows:
SELECT PRODUCT
READY FOR USE

! To disable the rinse cycle, see the paragraph on

programming the machine.

7
 Priming the water circuit Water filter (where installed)
GB
! Before starting the machine after long periods of The water filter purifies the water used in the
inactivity, if the water tank has been completely preparation of coffee.
emptied, it is essential to prime the machine circuit. Its properties reduce the hardness of water and remove
Moreover the circuit must be primed every time the the unpleasant taste of chlorine.
following is displayed:
The water filter may be installed at any time.

VENTILATE
Installing the water filter
1. To prime the circuit,
direct the steam spout 1. Open the front panel
over the drip tray. and remove the water
Place a cup or suitable tank.
container below the Empty the tank of any
steam spout and press water.
the key.

2. Remove the filter

2. Wait until the water packaging and set the
runs smoothly out of the calendar to the current
steam spout. month.
To interrupt, press the key.
! Refer to the notes for
After the above operations have been completed the using the filter below.
machine is ready for use.
3. Insert the filter into the
To dispense coffee, hot water or steam and for proper tank. The reference mark
use of the machine, carefully follow the instructions that and the groove should
are provided. coincide. Press down
completely.

Fill the tank with fresh

drinking water and
replace in the machine.
Close the front panel.

Dispense all the water in

Regulating water hardness the tank into a container.
Afterwards fill the tank
Regulate the machine to the right degree of water hard- again with water.
ness that you will use.
According to this setting, the machine advises when it is ! Program the machine
necessary to run a descaling cycle. for use with the filter
(see programming). The
Read the sections on “Water hardness” in “Program- machine informs the user when it is time to replace the
ming” to regulate hardness. filter.

! The water filter must always be removed before run-

ning the descaling cycle.

8
Additional information for correct use of Grinding regulation
the water filter (where installed) GB
! Take care when rotating the knob that regulates
For correct use of the water filter (where installed), grinding, which is inside the coffee hopper. Do not put
here are a number of recommendations: ground and/or freeze-dried coffee in the bean hopper.
1. Store the water filter in a cool place away from the
sun, at a temperature of between +5°C and +40°C; ! Do not put any material other than coffee beans in
2. Use in areas with temperature no higher than 60°C; the hopper.
3. It is advisable to wash the water filter if the machine
has been inactive for 3 days or more; Switch off at the mains before carrying out any type of
4. Replace filter if the machine has been inactive for operation inside the bean hopper.
20 days or more;
5. To preserve a filter that has already been opened, The quality and flavour of coffee depend on the
place in a plastic airtight bag and store in the grinding level, as well as the blend used.
refrigerator; do not store in freezer, as this will alter The machine has a knob to regulate the coffee
the properties of the filter; grinding.
6. Before using the filter, place in water in the tank for
30 minutes; To regulate the grinding,
7. Once removed from its package, do not store filter turn the knob one
in the open air; setting at a time. The
8. The filter must be replaced 90 days after it has been figures indicate the
removed from its package, or after it has filtered 60 fineness of grinding.
litres of drinking water.
The manufacturer
configures each
appliance on an
intermediate grinding
setting. If the grind is
too fine, rotate the knob
to a higher setting; if the grind is too coarse, turn the
knob to a lower setting.

The variation in grind will only be seen after one or two

coffees have been brewed.

Use coffee bean blends for espresso machines. Try

not to use high grinding settings (e.g. 1/10). Use
different coffee blends for these settings. Keep the
coffee in a fresh place in a sealed, airtight container.

Grinding must only be regulated if coffee is not brewed

properly:

• if it is brewed too fast, this means that the grind is

too coarse; turn the knob to a lower setting;

• if it is brewed in drips and/or intermittently, this

means that the grind is too fine; turn the knob to a
higher setting.

9
 Brewing

SBS System Wait for the cup to fill with the required amount. Press
GB the same key again.
The machine has a device to regulate the body of In this way the machine is programmed to brew the
coffee: SBS. quantity of coffee you require.
This system gives
optimal brewing with
any kind of coffee on the
market.
Brewing coffee (1 cup)
! Before brewing coffee, make sure the water tank and
the coffee tank are full and that the display shows:
! Regulation can even be
done while the coffee is SELECT PRODUCT
brewing. READY FOR USE

Place 1 cup beneath the

Turn the knob to brew unit spouts.
regulate.
Rotate knob: You can adjust the height
• left for crème café; of the brew unit to your
• to the centre for espresso; cups by shifting it up or
• right for a strong coffee. down manually.

Regulating the quantity of coffee per cup

The machine is programmed to brew 3 kinds of coffee:

espresso coffee with the key, To brew the coffee press the coffee brewing key ( ,
regular coffee with the key; or ). This is shown on the display (e.g.):
long coffee with the key.
1 SMALL COFFEE
To adjust the DISPENSING
programmed values to
the size of the cup, place In this operating mode the machine automatically grinds
the cup beneath the and measures out the right amount of coffee.
brew unit. Next the brew cycle is started.
1 SMALL COFFEE
Press the key
PREBREWING...
and using the
key scroll through the
functions until you get to: After the prebrewing cycle, the coffee begins to come
out of the brew unit spout.
PROGR. COFFEE LENG.* The display will show:
PROGR. WATER AMOUNT 1 SMALL COFFEE
Press the key; the display shows: DISPENSING

SELECT PRODUCT Dispensing stops automatically when the set level is

PROGRAMM. COFFEE reached.
press the key to brew the required type of coffee
( , or ); this is shown on the display (e.g.): ! It is nevertheless possible to interrupt dispensing of
coffee by pressing the key ( , or ).
1 SMALL COFFEE
PROGRAMM. COFFEE

10
Brewing coffee (2 cups) Dispensing hot water
GB
! Before brewing coffee, make sure the water tank and ! At the start, short spurts of hot water may be
the coffee tank are full and that the display shows: dispensed. Danger of scalding. The hot water spout
can reach high temperatures. Do not touch it with bare
hands.
SELECT PRODUCT
READY FOR USE Before dispensing water, make sure the following is
shown on the display:
Place 2 cups beneath SELECT PRODUCT
the brew unit spouts.
READY FOR USE
You can adjust the
height of the brew unit When the machine is
to your cups by shifting ready to brew coffee,
it up or down manually. proceed as follows:

1. Place a cup and/or a

container below the hot
To brew the coffee, press first the key, and then the water/steam spout.
coffee brewing key ( , or ). This is shown on
the display, e.g.:
2 SMALL COFFEES 2.Press the key; the display shows:
DISPENSING
HOT WATER
In this operating mode the machine automatically
grinds and measures out the right amount of coffee.
! A preset amount of water is dispensed. This may be
! The preparation of two coffees requires two grinding modified in the “PROGR. WATER AMOUNT” menu
cycles and two separate brew cycles. These are described in the chapter on “Programming”.
handled automatically by the machine.
To stop dispensing hot water, press the key again.
The machine returns to normal operating mode.
Next the brew cycle is started.
2 SMALL COFFEES
PREBREWING...

After the prebrewing cycle, the coffee begins to come

out of the brew unit spout.
The display will show:
Brewing steaming/cappuccino

Steam can be used to froth milk for cappuccino and

2 SMALL COFFEES also to heat beverages.
DISPENSING
! Danger of scalding! At the start, short spurts of hot
water may be dispensed. The brewing spout can reach
Dispensing stops automatically when the set level is
high temperatures: Do not touch it with bare hands.
reached.

! It is nevertheless possible to interrupt dispensing of

coffee by pressing ( , or ) key; If the first
coffee is interrupted, the second will not be dispensed.

11
 Maintenance and care

1. With the machine General cleaning

GB ready to brew coffee,
place a cup and/or a ! Maintenance and cleaning operations can only be
container below the hot carried out when the machine is cold and disconnected
water/steam spout. from the power supply.

2. Press the key to • Do not immerse the machine in water or place any of
discharge any water left its parts in a dishwasher.
in the steam spout; in a
short time, only steam • Do not use sharp objects or harsh chemical products
will come out of the (solvents) for cleaning.
spout.
The display shows: • Do not dry the machine and/or its components in a
microwave and/or conventional oven.
STEAM
• Clean the water tank
on a daily basis and
change the water.
3. Press the key to stop dispensing steam.

4. Fill 1/3 of the container you wish to use to prepare • Remove and clean
the cappuccino with cold milk. the filter in the tank.

! Use cold milk and a cold cup for better results when
preparing cappuccino. • Use a soft cloth
moistened with water to
5. Immerse the steam clean the appliance.
spout in the milk to be
heated and press the
key. Move the container • Clean the dispensing
gently up and down for outlet and the brew
uniform foam formation. group.

! Steam is dispensed for • We recommend

a preset amount of time. emptying and cleaning
This may be modified the drip tray and the
dregs drawer on a daily
in the “PROGRAM
basis. To do this, extract
STEAM TIME” menu described in the chapter on the drip tray then empty
“Programming”. and clean all parts.

6. Press the again to stop dispensing steam.

• The brew unit may be
! The same system can be used to heat other removed for cleaning:
beverages. 1. Lower the brew unit
spouts
2. Grasp the brew unit as
! After this operation, shown and extract it from
clean the steam spout its seat.
with a wet cloth. 3. Wash the whole unit in
hot water.

12
The brew group must be cleaned every time the coffee Descaling
bean hopper is filled and at least once a week. GB
Scale normally forms with use of the appliance.
• Switch off the Descaling is necessary every 3 - 4 months when
machine by pressing
there is a reduction in water flow or when the machine
the main switch to “O”.
displays the following message:
• Remove the drip READY FOR USE
tray and the dregs DECALCIFY
drawer. Open the
service door.
! If you want to descale the machine yourself, you can
• Remove the brew
use a non-toxic and/or non-harmful descaling product
group by the handle
for coffee machines, commonly available in the shops.
and press the key
Ariston descaling product is recommended.
marked “PUSH”.
! Never use vinegar as a descaler.
• Wash the two steel
filters of all coffee ! Remove the water filter before descaling (where
residues. installed).
• The brew group
Follow the instructions for descaling:
must be cleaned only
with warm water and
no detergents. Wash
all parts and dry 1. Mix the descaling
thoroughly. product with water
following the
• Thoroughly clean instructions on the
the inside compartment product package, and
of the machine. fill the tank with water.

• Take the handle and

return the brew group 2. Turn on the machine
to the compartment at the main switch.
clicking it into place.
Close the door.
3. Press the key for at least 5 seconds to select the
• Place the dregs function. The display shows:
drawer and the grill
in the drip tray before DECALCIFY
inserting into the machine. NO

! For perfect efficiency of the brew group, a 4. Using the keys, select:
maintenance kit is available from Ariston outlets.
DECALCIFY
YES

5. Direct the steam

spout towards the drip
tray.

6. Place a suitably
sized container below
the steam spout and
press the key.

13
 The machine will start an automatic descaling cycle Interrupting the descaling cycle
GB with pauses programmed by the manufacturer and
automatically managed by the machine. If the descaling cycle is interrupted by the machine
The display will show: switching off, it is resumed when the machine is
MACHINE IS DESCALING switched on again.

The descaling cycle may be interrupted by pressing the

6. At the end of the cycle, dispensing of the descaling key; the display shows:
solution will stop and the display will show: MACHINE IS DESCALING
RINSE MACHINE INTERRUPTED
FILL WATERTANK
press the key and the descaling cycle resumes. If
7. Rinse the water tank the key and the key are pressed, the display
thoroughly and fill it with shows:
fresh drinking water.
DESCAL. INTERRUPTED
EMPTY WATERTANK
Warning! After the operation, empty the water tank of
Replace the tank and the descaling solution and wash it with fresh drinking
close the front panel. water. The machine’s circuit must be washed with a
The display will show: rinse cycle.

RINSE MACHINE Proceed as for a normal rinse cycle as described at

point 7 of the previous chapter.
PRESS WATER KEY

8. Place a suitably sized

container below the
steam spout and press
the key.

Rinsing of the machine

circuits begins and the
display will show:
MACHINE IS RINSING

9. When the rinse cycle is complete, the display will

show:
RINSING FINISHED
PRESS WATER KEY

12. Fill the water tank, press the key, reprime the
circuits and leave the machine to heat up.

! If you are using a product other than the

recommended one it is important to follow the
manufacturer’s instructions shown on the pack of the
descaling product.

14
Programming

Setting machine functions Programmable functions

GB
The user can change a number of the machine’s
operating parameters according to personal
preference. STANDBY

When the appliance is used very little, it is possible

to select the STANDBY mode. This function reduces
energy costs. Nevertheless, it is recommended to
switch off the appliance at the mains if it is to be out of
service for long periods. The machine reheats in just a
few minutes when reactivated.
MENU command
Select the function by pressing the key
To change operating parameters, enter programming ENERGY SAVING *
mode with the key, when the machine is at rest. RINSING
In programming, select the required function and press
the key. This scrolls you through the functions and enable with the key. The display shows:
available on the machine.

To exit the programming, press the key. ENERGY SAVING

The machine is on but none of its components is

active.

To activate the machine press .

Changing individual functions

RINSING
Select the required function by pressing the
key. Immediately after heating, the appliance automatically
Enable the required function with the key. Scroll eliminates any water left in the internal ducts to ensure
through the variables using the key. To save that only fresh water is used to make coffee.
the required variable, press key.
The function has been enabled by the manufacturer.
Note: the key interrupts programming at any time
without saving changes. This operation is only possible To disable the function, press the key, select
before pressing the key. this function:
RINSING *
LANGUAGE

and enable it with the key. The display shows:

RINSING
ON

15
 Programming

Now, with the key select WATER HARDNESS

GB
RINSING Water hardness varies according to geographical
OFF region. Hence, the machine must be regulated for the
hardness of the water used. This is expressed on a
and save the choice using the key. scale of 1 to 4. The appliance is already programmed
for average hardness (3).

To regulate hardness,
LANGUAGE briefly dip (1 second) the
strip provided in water.
This function modifies the display language. Choose Next, shake the strip
from Italian, German, Portuguese, Spanish, English, gently to eliminate
French and Dutch. The machine is generally excess water. After one
programmed with the language of the country where it minute the test results
will be sold. are visible. Check the
number of squares that
To change the language, use the key to choose have changed colour.
this function:
Use the key to select this function:
LANGUAGE *
WATER HARDNESS *
CONTRAST
WATERFILTER
and enable it with the key.
Enable it with the key.
The display shows: The display shows:

LANGUAGE WATER HARDNESS

ENGLISH HARDNESS 3

Select the required language by pressing the Select the right hardness using the key (e.g. 2
key and use the key to save your choice. squares = Hardness 2) and save using the key.

! Warning: this setting allows the machine to notify

when it is time for descaling treatment.

CONTRAST
The display shows:

Regulates display contrast for better viewing. READY FOR USE

DECALCIFY
Use the key to select this function:
CONTRAST *
WATER HARDNESS WATER FILTER (where installed)

Enable it with the key. This function provides better management of the “water
filter (where installed), notifying the user when the filter
is to be replaced.
The display shows:
CONTRAST ! The function must be enabled when installing the
>¢¢¢¢¢ < 50 water filter for the first time.

Now select the required contrast by pressing the Use the key to select this function:
key and use the key to save your choice. WATERFILTER *
TEMPERATURE

16
Enable it with the key. PROGRAMMING COFFEE SIZE
GB
The display shows: This function enables you to regulate the amount of
coffee brewed when the ( , or ) keys are
WATERFILTER pressed.
OFF
You can program the amount dispensed one key at
Use the key to select a time Continue repeating the procedure described
below to program several keys.
WATERFILTER
ON Use the key to select the function:
PROGR. COFFEE LENG.*
and press the key to confirm. PROGR. WATER AMOUNT
! The “RESET” must be given whenever a new
Enable it with the key.
cartridge filter is installed.
The display shows:
For this command, use the key to select the
function: SELECT PRODUCT
WATERFILTER PROGRAMM. COFFEE
RESET ! In this phase, if the display remains idle for a certain
amount of time, the machine exits the function.
Enable it with the key.
Position the cup that you want to fill.
Press the key to brew the required type of coffee ( ,
or ); this is shown on the display (e.g.):

TEMPERATURE
1 SMALL COFFEE
This function regulates the temperature of the water DISPENSING
for coffee (high, medium and low). and then:

Use the key to select the function:

1 SMALL COFFEE
PROGRAMM. COFFEE
TEMPERATURE *
PROGR. COFFEE LENG. Wait for the cup to fill with the required amount. Press
the key again.
Enable it with the key.

The display shows (e.g.):

TEMPERATURE PROGRAMMING THE QUANTITY OF WATER
MEDIUM
This function enables you to regulate the amount of
water that is dispensed whenever is pressed. You
Select the required temperature by pressing the
need just one key to fill your container with the right
key and use the key to save your choice.
amount of water

Use the key to select the function:

PROGR. WATER AMOUNT*
PROGRAM STEAM TIME

17
 Programming

Enable it with the key. AROMA ESPRESSO

GB
The display shows: This function allows you to program a dosage (quantity)
setting for coffee beans to be ground for espresso
SELECT PRODUCT (strong, medium, mild).
PROGRAMM. WATER
Use the key to select the function:
Position the container that you want to fill and press . AROMA SMALL COFFEE *
Water is dispensed from the steam spout and the
AROMA COFFEE
display shows:
Enable it with the key.
HOT WATER
PROGRAMM. WATER The display shows (e.g.):
AROMA SMALL COFFEE
When the required amount is reached, press the
key again.
STRONG

The machine is now programmed. Select the required dose by pressing the key
and use the key to save your choice.

PROGRAMMING STEAM TIME

AROMA COFFEE
This function enables you to regulate how long steam is
dispensed whenever is pressed. This function allows you to program a dosage (quantity)
setting for coffee beans to be ground for coffee (strong,
Use the key to select the function: medium, mild).

PROGRAM STEAM TIME * Use the key to select the function:

AROMA SMALL COFFEE
AROMA COFFEE *
Enable it with the key.
AROMA LARGE COFFEE

The display shows: Enable it with the key.

SELECT PRODUCT The display shows (e.g.):

PROGRAMM. STEAM
AROMA COFFEE
Position the container with the drink that you want to
MEDIUM
heat and press the key.
Select the required dose by pressing the key
Steam is dispensed from the spout and the display and use the key to save your choice.
shows:
STEAM
PROGRAMM. STEAM

When the required amount is reached, press the

key again.

The machine is now programmed.

18
AROMA LONG COFFEE TOTAL COFFEES
GB
This function allows you to program a dosage This function displays the number of coffees already
(quantity) setting for coffee beans to be ground for dispensed by the appliance.
long coffee (strong, medium, mild).
Use the key to select the function:
Use the key to select the function:
TOTAL COFFEE *
AROMA LARGE COFFEE * TIMER
PREBREWING
Enable it with the key.
Enable it with the key.
The display shows (e.g.):
The display shows (e.g.):
TOTAL COFFEE
AROMA LARGE COFFEE 81
STRONG
Press key to exit.
Select the required dose by pressing the key
and use the key to save your choice.

TIMER

PRE-BREWING This function enables you to save energy when the

machine is not used for long periods.
The pre-brewing process enhances the aroma of This function is preset by the manufacturer and is
coffee to give it an excellent taste. This function automatically enabled.
moistens the coffee before it is actually brewed.

Use the key to select the function:

ENERGY SAVING
PREBREWING *
after 3 hours from the use.
TOTAL COFFEES
! Switch-off time can be regulated at 15-minute
Enable it with the key. intervals with a minimum of 15 minutes. The function
cannot be disabled.
The display shows (e.g.):
PREBREWING Use the key to select the function:
ON TIMER *
CLOCK
Use the key to choose whether to disable the
function:
Enable it with the key.
PREBREWING
OFF The display shows:
STANDBY
or to extend the phase AFTER 3:00
PREBREWING
LONG Select the automatic switch-off interval by pressing the
key and use the key to save.

to enhance the flavour of your coffee.

! Note: if automatic switch-on/off times are enabled in
“CLOCK” mode, this function will be ignored.
Save your choice using the key.

19
 Programming

CLOCK Use the key to choose whether to enable the

GB function
This function is enabled and/or disabled by the user
and: SHOW CLOCK TIME *
- displays the exact time when the machine is in ON
“STANDBY” or “SELECT FUNCTION” mode.
- selects the on/off time. Save using the key.

! Note: the time is only displayed at certain times. This

To correctly program this function, the exact time must function can only be disabled by the user.
be set
To disable this function, use the key to choose:
Use the key to select this function:

SHOW CLOCK TIME *

CLOCK * OFF
RINSING CYCLE
Save using the key.
Enable it with the key.

Use the key to select this function: Regulating on/off times

CLOCK TIME *
ON/OFF TIME The machine can be programmed to switch on and off
automatically. Only one “on” time and one “off” time can
be programmed on the machine.
Enable it with the key.
! Note: this function is enabled only if the main switch is
Use the key to select this function: in the “I” position (on).
CLOCK TIME
0:00 Use the key to select this function:
ON/OFF TIME *
Set the current time by pressing the key and SHOW CLOCK TIME
save using key;
Enable it with the key.
Next, press the key to set the minutes and save
using key. ON/OFF TIME
ON TIME 0:00
The time is set and the machine returns to the previous
menu. Set the “on” time by pressing the key and save
using the key.
! Note: the time is memorised when the machine is
switched off. Next, press the key to set the minutes and save
using key.
To display the time
ON/OFF TIME
Use the key to select this function: OFF TIME 0:00
SHOW CLOCK TIME *
AUTOMATIC ON/OFF Set the “off” time by pressing the key and save
using key.

Enable it with the key.

20
Next, press the key to set the minutes and RINSING CYCLE
save using key. GB
This function performs a rinsing cycle using water to
! Attention: if the on and off times coincide, the clean all components involved in brewing coffee.
machine ignores both settings. The clock must be
enabled after this programming in order to function ! A person should be present during the rinsing cycle
correctly. to supervise the operation. Before performing the
rinsing cycle fill the water tank.

To enable automatic on/off Use the key to select this function:

RINSING CYCLE *
! Note: this function is enabled only if on/off times has FACTORY SETTINGS
been programmed.

Use the key to select this function: Press the key.

AUTOMATIC ON/OFF * The display will show:

CLOCK TIME RINSING CYCLE
NO
Enable it with the key.

Use the key to select

AUTOMATIC ON/OFF
NO RINSING CYCLE
YES
In this case disables this function.

Enable the function with the key and when the Press the key to start the rinsing cycle. The display
display shows shows:

AUTOMATIC ON/OFF
RINSING CYCLE
YES

save using the key. The machine dispenses about half the quantity of
water contained in the tank from the brew unit.
Check the parameter settings when exiting
programming. If the current time falls within the Then the cycle stops automatically, and the display
disabled period the display shows: shows:
SELECT PRODUCT
ENERGY SAVING READY FOR USE

! Note: during the disabled phase the machine may

be reactivated at any time by pressing the key. To
disable the machine again, go into programming by
pressing and exit immediately by pressing the
key.

21
 Programming

Factory settings
GB
This function resets the machine’s operating
parameters to the manufacturer’s settings.

Use the key to select this function:

FACTORY SETTINGS *
EXIT

Enable it with the key.

The display then shows:

FACTORY SETTINGS
NO

Choose whether to restore parameters with the

key, and press the key to confirm.

! Warning: when all parameters are restored to factory

settings, all customised settings are lost.

22
Display messages

Display messages
GB
The machine’s display informs the user of how it is to
WASTE TRAY MISSING
be used. • Insert the drip tray and the dregs drawer correctly.
Here is a list of the alarm messages that prevent
coffee brewing and what the user should do to solve
the problem.
CLOSE DOOR
• Close the front door.
ENERGY SAVING
• Press the key “MENU/OK”.
CLOSE CONTROL PANEL
• Close the upper panel.
READY FOR USE
DECALCIFY
• Descale the machine.
VENTILATE
• Place a cup or suitable container below the steam
spout and press the key.
FILL WATERTANK Wait until the water runs smoothly out of the steam
• Fill the water tank with fresh drinking water. spout.
To interrupt, press the key.
! The machine requires the tank to be filled even when
the level is still high. This happens because the tank
of the coffee machine has been preset to house the
optional “water filter”, thus requiring a minimum level of
BREWUNIT BLOCKED
water in the tank for filtering to be performed.

GRINDER BLOCKED
COFFEE BEANS EMPTY • Contact an authorised customer service centre.
READY FOR USE
• Fill the hopper with coffee beans and start the
coffee brew cycle.

WASTE TRAY FULL

• Open the door, remove the dregs drawer and empty

the dregs into a suitable container.

! Important note: The dregs drawer must only be

emptied when the machine is switched on. The dregs
drawer must be removed for at least 5 seconds. If the
drawer is emptied when the machine is switched off, it
will not be possible to brew coffee when switched back
on.

BREWUNIT MISSING
• Insert the brew group correctly.

23
 Problems - causes - solutions

Problem Cause Solution

GB
The machine does not switch on The machine is not connected to the Check connection to the power
power supply supply
Coffee is not hot enough The cups are cold Warm the cups with hot water
No hot water or steam is dispensed Steam spout clogged Pull the steam spout downwards to
remove it, and clean
Coffee brews too slowly Coffee too fine Change coffee blend
Rotate the grind regulation knob to
the highest number
Brew group dirty Wash the brew group
SBS system knob turned all the way Turn the knob to the left and when
to the right the machine is brewing, turn toward
the right
Coffee brews too quickly Coffee too coarse Change coffee blend
Rotate the grind regulation knob to
a lower value
SBS system knob turned all the way When the machine is brewing, turn
to the left the knob to the right
The machine takes a long time to There are limescale deposits in the Run descaling cycle
heat up and the amount of water circuit
dispensed from the spout is too
small
The brew group does not come out The brew group is off position Turn the machine on. Close the
front door; the group returns to
the starting position and can be
removed.
Drip tray inserted Remove the drip tray
Coffee leaks out of the brew unit Brew unit in the wrong position Reposition the brew unit
Brew unit clogged Remove brew unit and wash
Coffee has little foam Unsuitable coffee blend or coffee is Change coffee blend
not freshly toasted
Coffee blend too coarse Regulate the grind
SBS system knob turned towards Turn the SBS system knob to the
the left right
Water overflowing from the drip tray Drip tray too full Check the position of the float and
empty the drip tray

24
Precautions and
recommendations
Intended use Cleaning
• The coffee machine is intended only for domestic • Before cleaning the machine, it is indispensable GB
use. to put the main switch on “O” and remove the plug
• Do not make any technical changes or use the from the power socket.
machine for unlawful purposes as this may lead to • Then, wait for the machine to cool down.
hazards! • Never immerse the machine in water! Prevent it
• The machine should only be used by adults in full from being sprayed with water.
possession of their physical and mental faculties. • It is strictly forbidden to tamper with the inside of the
machine.
Power supply
• Only connect the coffee machine to a suitable Storing the machine
power socket. • If the machine is to remain out of use for a long
• The voltage must correspond to the value on the time, switch off and unplug it from the socket. Store
rating plate. it in a dry place out of the reach of children.
• Keep it protected from dust and dirt.
Power cable
• Do not lay heavy objects on the front panel while
• Never use the coffee machine if the power cable is
open.
defective.
• Do not pass the cable around corners, over sharp Servicing / Maintenance
edges or over hot objects and keep it away from oil. • In case of failure, faults or suspected faults, unplug
• Do not pull out the plug by tugging at the power immediately. Never attempt to operate a faulty
cable or touch it with wet hands or feet. machine.
• Servicing and repairs must only be carried out by
Protecting others Authorized Customer Service Centres.
• Ensure that the coffee machine is out of children’s • The manufacturer accepts no responsibility
reach. Children are not aware of the risks linked for servicing and/or repairs not carried out by
with electrical appliances. authorised customer service centres.
• Do not leave the coffee machine packaging within
the reach of children. Fire safety
• In the event of fire, use carbon dioxide extinguishers
Danger of burning (CO2). Do not use water or dry-powder
• Never direct the jet of hot water and/or steam extinguishers.
towards yourself or others. Danger of scalding.
Always use the handles or knobs provided. Disposal
• Do not insert objects into the openings on the • Disposal of packaging materials: comply with local
appliance. regulations for recycling of used packaging.
• European Directive 2002/96/EC on waste electrical
Installation area, use and maintenance and electronic equipment (WEEE), states that
• Do not obstruct the ventilation or heat discharge electrical household appliances must not be
openings. disposed of a normal solid urban waste. Old
• Choose a location that is sufficiently lit, clean and appliances must be collected separately to optimise
near a socket that is easy to reach. the rate of recovery and recycling of the materials of
• Do not place the machine on hot surfaces and close which they are composed, and to prevent potential
to open flames to prevent the casing from melting or damage to health and the environment. The crossed
being damaged. through basket symbol is used on all products as a
• Allow a distance of 10 cm between walls and reminder that they must be disposed of separately.
cooking hotplates. Electrical appliances in disuse can be delivered
• Do not keep the machine at a temperature below to the public refuse collection service or taken to
0°C; freezing may damage the machine. special municipal areas. Otherwise, depending on
• There must be easy access to the socket at all national legislation, they may be taken to the retailer
times. at the time of purchase of a similar product.
• Do not use the coffee machine outdoors. All the main manufacturers of household
appliances are actively involved in the creation
and management of collection and disposal of
appliances in disuse.

25
GB

26