Fosroc Trafficguard UR constructive solutions

Skid resistant, flexible, waterproof protection flooring

system

Uses Instructions for use

Trafficguard UR is a modified polyurethane-based traffic deck Surface Preparation

system designed to provide an added level of protection to,
New concrete surfaces should have reached 80% of their
new and existing, heavily trafficked areas such as:
intended physical properties - generally only achieved after a
„ Car parks minimum curing period of 28 days. Existing concrete surfaces
must be prepared to provide a clean, sound substrate.
„ Industrial manufacturing units
Surfaces should be clean and dry with open capillary, free
„ Warehouses
from laitance, oil & grease, curing compounds or other surface
contaminants which may prevent full and proper adhesion of
Advantages
the primer. All blowholes, and other surface undulations
„ Flexible and tear resistant greater than 1 mm in depth, should be repaired using
Nitomortar FC(B)*†.
„ Waterproof
Temperature of the substrate during application must be
„ Seamless
between 5°C and 40°C.
„ Rapid application, reliable and safe
Priming
„ Available in a range of colours
Apply Trafficguard Primer to the prepared surface at a wet film
thickness of 200 microns.
Description
Whilst Trafficguard Primer is still wet, seed with Fosroc Anti
Trafficguard UR is a multi-layer deck protection system
Slip Grain No. 3 at a rate of 0.4 kg / m2 and allow to cure for 24
comprising a primer, flexible & waterproof Membrane and
hours.
UV resistant wearing course. All components are applied in
the liquid phase and react chemically to form a tough, flexible, Application
waterproof, protective surface.
Membrane

Apply Trafficguard Membrane to the primed surface at a wet

film thickness of 750 microns. For best results the Trafficguard
Properties
Membrane should be applied with a notched trowel or
Membrane squeegee.
Elongation (ASTM D412) : >100% Whilst the base coat is still wet apply Fosroc Anti Slip Grain
Tensile Strength (ASTM D412) : 6.0 N/mm² No. 1200 at a rate of 0.4 kg / m2. Allow to cure for 12 hours
Wearcourse prior to applying the wear course.
Weathering (30 days) : No change in Wear Course
(ASTM G53) original appearance
Corrosion Resistance : No change in Apply Trafficguard Wear Course to the base coat at a wet film
(ASTMB117) original appearance thickness of 140 microns. Allow to cure for 24 hours prior to
Humidity Resistance : No change in trafficking.
(water Fog exposure) original appearance Cleaning

Tools and equipment should be cleaned with immediately

after use with Fosroc Solvent 102*.
Trafficguard UR
Fosroc Trafficguard UR

Estimating Precautions

Supply Health and safety

Trafficguard Primer : 9 litre packs
Trafficguard Primer, Membrane and wear course and Fosroc
Trafficguard Membrane : 8 litre packs
Solvent 102 should not come in contact with skin or eyes, nor
Trafficguard Wear Course : 20 litre packs
should they be swallowed. Avoid inhalation of vapours and
Antislip Grains No. 1200, 3 : 25 kg bags
ensure adequate ventilation.
Coverage
Some people are sensitive to resins, hardeners and solvents.
Trafficguard Primer : 5.0 m2/litre
Wear suitable protective clothing, gloves and eye/face
Trafficguard Membrane : 1.3 m2/litre
protection. Barrier creams such as Kerodex Antisolvent or
Trafficguard Wear Course : 4.7 m2/litre
Rozalex Antipaint provide additional skin protection.
Antislip Grains No. 1200, 3 : 0.4 kg / m²
Should accidental skin contact occur, remove immediately
Note: The above coverage rates are given for guidance only
with a resin removing cream such as Kerocleanse Standard
as actual quantities used will vary depending upon
Grade Skin Cleanser or Rozaklens Industrial Skin Cleanser,
the nature of substrate and conditions on site.
followed by washing with soap and water - do not use solvent.

Storage The use of goggles is recommended, in case of accidental

eye contamination, rinse immediately with plenty of water
Shelf life
and seek medical advice.
When stored in warehouse conditions at less than 25°C,
If swallowed seek medical attention immediately - do not
Trafficguard UR will have a shelf life of 12 months. Avoid
induce vomiting.
storage of material under direct sunlight.
Fire
Technical Support
Fosroc Solvent 102 is flammable. Do not use near a naked
Fosroc offers a full technical support package to specifiers, flame.
end users and contractors, as well as on-site assistance in
Flash points
locations all over the world.
Fosroc Solvent 102 : 33°C

Limitations

- Do not proceed with application if precipitation is imminent,

temperatures are expected to drop below 7°C within 24
hours of application.

- Trafficguard UR should not be applied onto substrate known

to suffer from rising dampness, having R.H. greater than
75% as measured in accordance with BS 8203 Appendix A
or having moisture content greater than 5% as measured
by a Hammond concrete/mortar moisture tester (type COCO). * Denotes the trademark of Fosroc International Limited
†
- Do not proceed with application if an osmotic condition is See separate data sheet
known or is suspected to exist.
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: agf@fosroc.com
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: abudhabi@fosroc.com
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: bahrain@fosroc.com
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: kuwait@fosroc.com

www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: oman@fosroc.com
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: qatar@fosroc.com

UAE/0291/10/M