GX3 Mac Driver Installation Guide

EZ-USB® GX3™ Mac OS X Driver
Installation Guide
Cypress Semiconductor
198 Champion Court
San Jose, CA 95134-1709
Phone (USA): 800.858.1810
Phone (Intnl): 408.943.2600
http://www.cypress.com
Copyrights
© Cypress Semiconductor Corporation, 2016. The information contained herein is subject to change without notice.
Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a
Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted
nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an
express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical
components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury
to the user. The inclusion of Cypress products in life-support systems application implies that the manufacturer assumes all
risk of such use and in doing so indemnifies Cypress against all charges.
Trademarks
GX3 is a trademark and EZ-USB is a registered trademark of Cypress Semiconductor Corp. All other trademarks or
registered trademarks referenced herein are property of the respective corporations.
Source Code
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected
by and subject to worldwide patent protection (United States and foreign), United States copyright laws and international
treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use,
modify, create derivative works of, and compile the Cypress Source Code and derivative works for the sole purpose of
creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or
representation of this Source Code except as specified above is prohibited without the express written permission of
Cypress.
Disclaimer
CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described
herein. Cypress does not assume any liability arising out of the application or use of any product or circuit described herein.
Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure
may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support
systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against
all charges.
Use may be limited by and subject to the applicable Cypress software license agreement.
2
Contents
1. Introduction ........................................................................................................................................................... 4
2. Driver Installation Procedure ................................................................................................................................. 4
3. Driver Uninstallation Procedure ............................................................................................................................ 9
3
1. Introduction
This document provides detailed information on the installation and the uninstallation of the EZ-USB® GX3™ Mac OS X v10.6
to v10.11 driver. The sections below show the step-by-step information on how to install the driver and verify the version
number of the driver installed. The document also explains on how to enable the GX3 based Ethernet network and configure it
on the Mac OS.
2. Driver Installation Procedure

1. Download the GX3 driver for Mac OS from www.cypress.com/gx3software. Unzip the package into a folder.
2. The GX3 Mac OS driver installation package is CYUSB3610.dmg.
3. Double click on the CYUSB3610.dmg file and a virtual disk named CYUSB3610 will appear on the Desktop as shown in
Figure 2-1.
Figure 2-1. Virtual disk CYUSB3610
4. Click the CYUSB3610_v2.8.0.pkg and the driver setup dialog box will pop-up as shown in Figure 2-2. Click the Continue
button to start the installation operation and follow the instructions.
4
Figure 2-2. Driver Installation Dialog box
5. Click the Install button to continue installation operation as shown in Figure 2-3.
.Figure 2-3. Installation procedure
5
6. The OS may ask for the user permission before beginning to install. Please enter your username and password to grant
permission for installation as shown in Figure 2-4.
Figure 2-4. User permission before installation
7. Click on the Continue button to proceed further as shown in Figure 2-5.

Figure 2-5. Continue installation
8. Once the installation is complete, click on the Restart button as shown in Figure 2-6 to restart the Mac OS for the latest
GX3 driver to take effect.
Figure 2-6. System Restart
6
9. After system re-boot, plug CY4701/CY4702 board or any device with GX3 on it to the USB port of the MacBook. Open
System Information and refer to the details as shown in Figure 2-7. Please check whether the driver is installed properly
or not.
Figure 2-7. GX3 System Information
10. The driver version can be checked by running the kextstat command from the terminal window. The driver version can
also be checked from the System Information > Software > Extensions > CYUSB3610 as shown in Figure 2-8.
7
Figure 2-8. Driver details and version information
11. Click on Network to add a new CYUSB Ethernet network interface as shown in Figure 2-9. Click on Apply button.
Figure 2-9. Configuring the Network
8
12. The new CYUSB3610 network interface is ready for operation and the green indication besides CYUSB3610 assures the
network is ready. The network parameters can be seen in the Systems Information under Network tab as shown in
Figure 2-10.
Figure 2-10 Network Information
3. Driver Uninstallation Procedure

The GX3 CYUSB3610 Mac OS driver can be uninstalled using the CYUSB3610_Uninstall exe file. Please follow the below
steps to uninstall the GX3 driver.
1) Click on the CYUSB3610.dmg so that CYUSB3610 virtual drive appears as shown in Figure 3-1.
Figure 3-1. CYUSB3610 Virtual drive
9
2. Click CYUSB3610_Uninstall_v140 to uninstall the Mac OS driver. The operating system may ask for the administrator
password to finish uninstallation process as shown in Figure 3-2.
Figure 3-2. Driver Uninstallation
10

GX3 Mac Driver Installation Guide

Uploaded by

Copyright:

Available Formats

GX3 Mac Driver Installation Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

GX3 Mac Driver Installation Guide

Uploaded by

Copyright:

Available Formats

EZ-USB® GX3™ Mac OS X Driver

2. Driver Installation Procedure

7. Click on the Continue button to proceed further as shown in Figure 2-5.

3. Driver Uninstallation Procedure

You might also like