Manual Book Sharp Aquos LC-32LE260M
Manual Book Sharp Aquos LC-32LE260M
Manual Book Sharp Aquos LC-32LE260M
1st Addition
SERVICE MANUAL
No. S94M55LC-32LE260M
LED BACKLIGHT TV
MODEL: LC-32LE260M
OUTLINE
This model is based on the LC-32LE265M and is changed some parts.This Service Manual covers the
modification alone. For the other points, please refer to the LC-32LE265M Service Manual.
CONTENTS
CHAPTER 3. SPECIFICATIONS
[1] SPECIFICATIONS 3-1
CHAPTER 4. ADJUSTMENT
[1] ADJUSTMENT 4-1
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
LC
S ervice work s hould be performed only by qualified s ervice technicians who are thoroughly familiar with all s afety checks and the
s ervic ing guidelines which follow:
WAR NING All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
1. F or continued safety, no modification of any circuit should be only for the purpose of completing these checks.)
attempted.
Any reading of 0.74 Vrms (this corresponds to 0.5 mA rms AC .) or
2. Disconnect AC power before servicing. more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
B E F OR E R E T UR NING T HE R E C E IVE R (F ire &
S hock Hazard)
B efore returning the receiver to the us er, perform the following
s afety checks : DVM
3. Inspect all lead dress to make certain that leads are not pinched, AC S C ALE
and check that hardware is not lodged between the chassis and
other metal parts in the receiver. 1.5k ohm
4. Inspect all protective devices such as non-metallic control knobs, 10W
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
0.15 µF
the following manner.
T E S T P R OB E
• P lug the AC cord directly into a 110-240 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paral-
leled by a 0.15 F capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or elec-
trical ground connected to an earth ground. T O E XP OS E D C ONNE C T T O
• Use an AC voltmeter having with 5000 ohm per volt, or higher, sen- ME T AL P AR T S K NOWN E AR T H
G R OUND
sitivity or measure the AC voltage drop across the resistor.
• C onnect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
S A F E T Y NOT IC E
Many electrical and mechanical parts in LC D colour television have F or continued protection, replacement parts must be identical to those
special safety-related characteristics. used in the original circuit.
T hese characteristics are often not evident from visual inspection, nor T he use of a substitute replacement parts which do not have the same
can protection afforded by them be necessarily increased by using safety characteristics as the factory recommended replacement parts
replacement components rated for higher voltage, wattage, etc. shown in this service manual, may create shock, fire or other hazards.
R eplacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by " " and shaded areas in the R eplacement P arts List
and S chematic Diagrams.
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
1–1
LC-32LE260M
[2] PRECAUTION FOR USING LEAD-FREE
SOLDER
Indicates lead-free solder of tin, silver and copper. Indicates lead-free solder of tin, silver and copper.
Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 qC which is higher than the conventional lead solder by 40 qC, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
PRICE PART
PARTS CODE DESCRIPTION
RANK DELIVERY
ZHNDAi123250E BL J I0.3mm 250g (1roll)
ZHNDAi126500E BK J I0.6mm 500g (1roll)
ZHNDAi12801KE BM J I1.0mm 1kg (1roll)
1–2
LC-32LE260M
OUTLINE
This model is based on LC-32LE265M and ƉĂƌƟĂůLJ ŵŽĚŝĮĞĚ͘
For contents not covered in this Service DĂŶƵĂů͕ĂĐĐŽƌĚŝŶŐůLJ ,please refer to
LC-32LE265M Service DĂŶƵĂů͘
SUPPLIED ACCESSORIES
X3 OPERATION MANUAL TINS-G227WJZZ TINS-G237WJZZ CHINESE-S
X3 OPERATION MANUAL TINS-G228WJZZ TINS-G238WJZZ ENG/ARABIC
X3 OPERATION MANUAL TINS-G233WJZZ TINS-G243WJZZ FRE/POR
X3 OPERATION MANUAL TINS-G230WJZZ TINS-G240WJZZ INDO
X3 OPERATION MANUAL TINS-G229WJZZ TINS-G239WJZZ THAI
X3 OPERATION MANUAL TINS-G235WJZZ TINS-G245WJZZ ENG SPC
X3 OPERATION MANUAL TINS-G234WJZZ TINS-G244WJZZ KAZ/RUS
X3 OPERATION MANUAL TINS-G232WJZZ TINS-G242WJZZ FRE
X8 RF ADAPTOR - QCNCWA969WJZZ ADD
X9 ERRATA SHEET - TCAUHA617WJZZ ADD
2–1
LC-32LE260M
CHAPTER 3. SPECIFICATIONS
[1] SPECIFICATIONS
Specifications
Item Model LC-32LE260M
LCD panel 80 cm
Resolution 1,049,088 pixels (1366 g 768)
Video Colour System PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV TV-Standard PAL: B/G, D/K, I SECAM: B/G, D/K, K/K1 NTSC: M
Function
Receiving VHF/UHF 43.25—863.25 MHz
Channel
CATV S1—S41ch (including Hyperband)
TV-Tuning System Auto Preset 99 ch
STEREO/BILINGUAL NICAM: B/G, I, D/K A2 stereo: B/G
Viewing angles H : 176º V : 176º
Audio amplifier/Speakers 5 Wg 2 / 4 g 7 cm 2pcs
Terminals Antenna input UHF/VHF 75 q DIN type
INPUT 1 / INPUT 2 HDMI (HDMI input, PC input)
INPUT 3 VIDEO in, AUDIO in, COMPONENT in
INPUT 4 VIDEO in, AUDIO in
OUTPUT AUDIO out, Headphone ( 3.5 mm stereo)
USB USB
USB device/File system USB Memory / FAT/FAT32
Photo file format JPEG (.jpg) (DCF2.0 compliant). Progressive format jpeg files are not supported.
Music file format MP3 (.mp3) Bitrate: 32 k, 40 k, 48 k, 56 k, 64 k, 80 k, 96 k, 112 k, 128 k, 160 k,
(Files may not be playable 192 k, 224 k, 256 k, 320 kbps
depending on the bitrate) Sampling frequency: 32 k, 44.1 k, 48 kHz
OSD language English/Simplified Chinese/Arabic/French/Portuguese/Russian/Persian/Thai/
Vietnamese/Indonesian
Power Requirement AC 110—240 V, 50/60 Hz
Power Consumption 41 W (1.0 W Standby)
without stand 739 (W) g 440 (H) g 93 (D) mm
Dimensions
with stand 739 (W) g 482 (H) g 174 (D) mm
Weight 5.7 kg (without stand) / 6.5 kg (with stand)
Operating Temperature 0°C — 40°C
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
3–1
LC-32LE260M
CHAPTER 4. ADJUSTMENT
[1] ADJUSTMENT
This adjustment page is only covering MAIN SOFTWARE PACKAGE & FACTORY SETTING,
for contents not covered in this page ,please refer to the LC-32LE265M Service Manual .
2. FACTORY SETTING
Model Name Factory Setting Remote Control S-System Setting OSD Language
Key Name Code Setting
4–1
LC-32LE260M
CHAPTER 5. TROUBLESHOOTING
TABLE
[1] TROUBLESHOOTING TABLE
Is the AC cord connector tightly connected to the set? NO Reconnect the AC cord tightly and turn on the power again.
YES
Are the wire harnesses and other cables properly connected in NO Reconnect the wire harnesses and other cables properly in the
the set? set.
YES
Are the DC/DC converter outputs and the output voltages along NO Check the DC/DC converters and the control lines. Replace
the control lines as specified? defective parts as required.
1) D+5.0V (I C9601)
2) D+3.3V ( IC9602)
3) D+1.26 V (I C9604)
4) D+3.3V (IC9603)
5) D+1.8V (IC9606)
6) D+2.5 (IC9608)
YES
Is there 7.5V from IC9605 & IC9603 NO Check the AC_CTRL Line (90) of IC3301 , IC3101,X 3301
crystal oscillation
YES
Replace IC3301
5–1
LC-32LE260M
Is there IF output from the tuner pin( 8 ) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there VIF input at pin 51 & 52 of IC3301? NO Check the circuit between TU1101 & IC3301.
YES
Are there the signal outputs of IC3301(pin 33) ? NO Check IC3301 and its peripheral circuit.
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
Is INPUT 3 selected on the input select menu screen? NO Select INPUT 3 on the input select menu screen to pick up the
right input signal.
YES
Is there the video signal input at pin (31 ) of IC3301? NO Check the line between pin (7) of TL509 and pin (31) of IC3301.
YES
Are there LVDS signal outputs of IC3301 at pin 61-64 and pin NO Check IC3301 and its peripheral circuits.
66-71
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
5–2
LC-32LE260M
Is INPUT 2 selected on the input select menu screen? NO Select INPUT 2 on the input select menu screen to pick up the
right input signal.
YES
Are there the Y, Pb and Pr signal inputs at pins (22), (24) and NO Check the line between pins (10)/(11)/(12) of TL504 ,TL505,
(26) of IC 3301 respectively? TL506 and pin (22),(24),(26)
YES
Is input waveform of IC3301 normal? NO Check the line between pins (10)/(11)/(12) of TL504 ,TL505,
Y=(24)pin , Pb=(22) pin, Pr=(26) pin TL506 and pin (22),(24),(26)
YES
Are the LVDS signal output from IC3301 at pin 61-64 NO
Check IC3301 and its peripheral circuits.
and pin 66-71 ?
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
Is INPUT 1 selected on the menu screen? NO Select INPUT 1 on the input select menu screen to pick up the
right signal input.
YES
Are there signal outputs from SC1501 to IC3301? NO Check peripheral circuits between SC1501 and IC3301.
YES
Are there LVDS signal outputs of IC3301 at pin 61-64 and pin NO Check IC3301 and its peripheral circuits.
66-71
YES
Check LVDS cable, LCD controller (incl. panel) and their periph-
eral circuits.
5–3
LC-32LE260M
Is the IF output from the tuner pin (8) of TU1101 as specified? NO Check TU1101 and its peripheral circuits.
YES
Is there the I2C signal input at pins (55), (56) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there audio signal intput at pin(4),(10) of IC1701? NO Check connection between IC3301 and IC1701 and its
peripheral circuits.
YES
Is the L-ch audio signal output at pin(26),(27),(29),(30) of IC1701 NO Check IC1701 and its peripheral circuits.
normal ?
Is the R-ch audio signal output at pin(20),(21),(23)(24) of IC1701
normal ?
YES
Are the audio signal L-ch and R-ch output at (1)/(2) and (3)/(4) of NO Check circuit between IC 1701 & P1701.
P1701 normal?
YES
Check speakers and their peripheral circuits.
5–4
LC-32LE260M
YES
Is there the I2C signal input at pin (55), (56) of IC3301? NO Check IC3301 and its peripheral circuits.
YES
Is there audio signal input at pin(4),(10) of IC1701? NO Check connection between IC3301 and IC1701 and its periph-
eral circuits.
YES
Is the L-ch audio signal output at pin(26),(27),(29),(30)of NO Check IC1701 and its peripheral circuits.
IC1701
YES
Are the audio signal L-ch and R-ch output at (1)/(2) and (3)/(4) of NO Check circuit between IC1701 & P1701 .
P1701 normal?
YES
Check speakers and their peripheral circuits.
5–5
LC-32LE260M
Does the HDMI image appear onscreen? NO Refer to “<INPUT 1> in No external input video onscreen
(HDMI)”.
YES
No audio output from <INPUT 1> NO Check the EDID.
YES
Are waveforms input in to the pins of IC3301 normally? NO Check peripheral circuits IC3301.
YES
Is there audio signal input at pin (4),(10) of IC1701 NO Check connection between IC3301 and IC1701 and its periph-
eral circuits.
YES
Is the L-ch audio signal output at pin(26),(27),(29),(30) of IC1701 NO Check IC1701 and its peripheral circuits.
normal ?
Is the R-ch audio signal output at pin (20),(21),(23),(24) of IC1701
normal ?
YES
Are the audio signal L-ch and R-ch output at (1)/(2) and (3)/(4) of NO Check circuit between IC1701 & P1701.
P1701 normal?
YES
Check speakers and their peripheral circuits.
5–6
LC-32LE260M
YES
Is there the L-ch audio signal input from pin (2) of external input
terminal J501 (HDMI AUDIO IN) to pin (28) of IC3301?
Is there the R-ch audio signal input from pin (3) of external input
terminal J501 (HDMI AUDIO IN) to pin (29) of IC3301?
YES
Are I2S signal output from the pins (42), (43) of IC3301 normally? NO Check peripheral circuits of IC3301.
YES
Is there audio signal input at pin(22),(32) of IC1702 NO Check connection between IC3301 and IC1702 and its periph-
eral circuits.
YES
Is the L- ch audio signal output at pin ( 10 ),(11),(16),(17) of NO Check IC1702 and its peripheral circuits.
IC1702 normal ?
Is the R- ch audio signal output at pin(2),(3),(8),(9) of IC1702
normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of NO Check circuit between IC1702 & P1702.
P1702 normal?
YES
Check speakers and their peripheral circuits.
5–7
F
B
C
D
H
A
G
1
GRAM
㼀㻱㻹㻼㻌㻿㻱㻺㻿㻻㻾
㼀㻴㻟㻟㻜㻝 㻯㻻㻺㼀㻾㻻㻸 㻿㼃
㻯㻻㻺㼀㻾㻻㻸㻌㻿㼃
㻾㻴㻙㻴㼄㻭㻜㻡㻣㼃㻶㻽㼆 㻿㻝㻜㻝㻌㼪㻌㻿㻝㻜㻣
+3.3V
㼄㼀㻭㻸㻔㻞㻣㻹㻴㼦㻕 㻾㻱㻿㻱㼀㻌㻵㻯
㼄㻟㻟㻜㻝 㻵㻯㻟㻟㻜㻞
2
㻾㻯㻾㻿㻯㻭㻞㻟㻣㼃㻶㻽㼆㼅 㼂㻴㻵㻼㻿㼀㻤㻠㻞㻥㼁㻙㻝㼅
ࠉࠉࠉࠉ
KKEY 1
KKEY 2
KKEY 0
XIN/XOUTT
LED_IR PWB
3
㻻㻲㻸
㻲㻾㻻㻹㻺㻳㻼㻵㻻㼇㻞㼉 A
㻮㻸㼋㻱㻾㻾 C
㻿㼀㻮
㻵㻞㻯㻌㻭㻰㻰㻾㻱㻿㻿䠖㻯㻜
㻵㻞㻯 㻝 㻞㻢㼂
㻝㻚㻞㻢㼂 㻲㻾㻻㻹㻌㻯㻼㼁㻌
㻿㼀㻮㼅㻌㻯㼀㻾㻸
4
㻝㻟㻚㻡㼂
TO PANEL 㻗㻟㻚㻟㻜㼂
HPD0_IN
㻴㻻㼀㻼㻸㼁㻳
5
I2C(HDMI)
㻵㻺㻼㼁㼀㻞 㻹㻿㼀㻣㻤㻟㻝㻸㻹㻷
CHAPTER 6. SYSTEM BLOCK DIA-
㻴㻻㼀㻼㻸㼁㻳
6–1
㼀㻾㻭㻺㻿㻵㻿㼀㻻㻾㻌
㻵㻺㻼㼁㼀㻌㻟 㻵㻺㻼㼁㼀㻟㼋㼅㻛㻯㼂㻮㻿㻘㻼㼎㻘㻼 㻿㼃
㻿㻻㻳㻵㻺㻝㻛㻳㻺㻝㻼㻛㻯㼂㻮㻿㻝㼋㻾㻵㻺㻝㻼㻛㻮㻵 㻳㻼㻵㻻㼇㻟㼉
㻯㻻㻹㻼㻻㻺㻱㻺㼀㻛㻭㼁㻰㻵㻻㻌㻵㻺 㻔㻲㻻㻾㻌㼃㼄㻳㻭㻌
㻵㻺㻼㼁㼀㻟㻌㻸㻛㻾 㻮㻸㼋㻻㻺
㻻㻺㻸㼅㻕
㻵㻺㻼㼁㼀㻌㻠㻌
㻵㻺㻼㼁㼀㻠㼋㻯㼂㻮㻿 㻯㼂㻮㻿㻜
㻯㼂㻮㻿㻛㻭㼁㻰㻵㻻㻌㻵㻺
6
㻸㻵㻺㻱㻵㻺㼋㻸㻜㻛㻾㻜
㻵㻺㻼㼁㼀㻠㻌㻸㻛㻾
㼁㻭㻾㼀㻌㻶㻭㻯㻷
㻶㻟㻟㻜㻝
㻽㻶㻭㻷㻶㻭㻜㻞㻣㼃㻶㼆㼆 㼁㻭㻾㼀 㻼㻺㻸㻝㻞㼂㻌
㻸㼃
㻸㼂㻰㻿㻌
㻿㻯㻟㻤㻜㻝
㻟㻞㻎㻦㻌㻤㻌㼎㼕㼠 㻰㻭㼀㻭㻌㻭㻔㻤㻕 㻟㻜㼜㼕㼚㻌 㻰㻭㼀㻭㻌㻭㻔㻤㻕
㻯㻸㻷 㻭㻔㻞㻕 㻲㻲㻯 㻯㻸㻷㻌㻭㻔㻞㻕
㼁㻿㻮
㻼㻭㻺㻱㻸
㻶㻟㻤㻜㻝 㻵㻞㻯
㼁㻿㻮㻌㻵㻲 㻟㻞㻎㼃㼄㻳㻭
㻽㻿㻻㻯㼆㻭㻟㻝㻥㼃㻶㻽㼆
㻡㻜㻛㻢㻜㻴㼦
7
㻡㼂㻌㻿㼃㻵㼀㻯㻴 +5.0V
㻽㻡㻜㻝㻌㻒㻌㻽㻡㻜㻞
㼂㻿㻷㼀㻭㻝㻡㻟㻡㼀㻗㻙 㻲㻾㻻㻹㻌㻯㻼㼁㻌㻿㼀㻮㼅㻌㻯㼀㻾㻸
HP_IN
㻳㻼㻵㻻㼇㻢㼉
8
HP MUTE
㻿㻼㻵㻌㻵㻲 㻸㻵㻺㻱㻻㼁㼀㼋㻸㻜㻛㻾㻜
㻾㻱㻿㻱㼀㻌㻵㻯
㻵㻯㻝㻣㻜㻞
㻿㻼㻵
㻼㻻㻼㻌
㻺㻻㻵㻿㻱㻌
㻯㻛㻹
㻿㼀㻮㼅㻌㻯㼀㻾㻸
㻿
㻿㻼㻌㻹㼁㼀㻱
㻿㻼㼋㻸
㻿㻼㼋㻾
㻿㻼㻵㻌㻲㻸㻭㻿㻴㻌
㼃㻾㻵㼀㻱
UR+13.5V
9
+3.3V
㻭㼁㻰㻵㻻㻌㻭㻹㻼
㻵㻯㻝㻣㻜㻝
㻿㻼㻵㻌㻲㻸㻭㻿㻴 㼂㻴㻵㼀㻼㻭㻟㻝㻟㻜㻰㻙㻝㼅
㻹㻭㻵㻺 㻵㻯㻟㻝㻜㻝
㼂㻴㻵㼃㻞㻡㻽㻟㻞㻮㼂㻙
㻿㻼㼋㻸
㻝㼅㻌㻟㻞㻹㻮㼕㼠
㻿㻼㼋㻾
TO DC DC CONVERTER, TUNER
LDO. USB, FLASH & HP AMP.
㻿㻼
㻼㻝㻣㻜㻞㻝
㻠㼜㼕㼚
㻿㻼㼋㻸
ࠉࠉࠉࠉࠉࠉࠉ
㻿㻼㼋㻾
㻿㻼㼋㻸 㻿㻼㼋㻾
10
㻤䃈㻌㻡㼃 㻤䃈㻡㼃
LC-32LE260M
LC-32LE260M
1 2 3 4 5 6 7 8 9 10
7–1
LC-32LE260M
1 2 3 4 5 6 7 8 9 10
7–2
F
B
C
D
H
A
G
1
(QKITPG492WJTN) KG492WE
LF1
QPWBNG492WJZZ
a
LC-32LE260M
FDC4
LW
2
T2 C1105 R1105
POW SC3801
FDC4 R3816
R1106
P3802
P3802 30 C1109
SC3801
R1109 C1108 C1115
HAND 1 FDC2
R3817 R3818
1
R3819
R1110 R1114 FB1101 TU1101
R3809
Q3802 Q3302
C3801 R3815R3812R3814R3813R3811 R3319
R3810
C1112
FDC2
UR1 1 R1103
3
13 C3802 R1104
R1111 TU1101
C1110
C9627 R3806
R7831
94V-0 R3802 Q3801
C1111
C7819
R1112
R3807
P3301
P3301 R1113
J3301
FB3802 FB3801
CHECKER J502
FB3309
J3301
L9601
4
R9617 C3313
C9614
7
Q1704
L9602 C9608
X3301
X3301
9
12
C3309C3345
C3339R3331 R1737R1734 C1737 R1739
IC1702
13
L9601 C1743
C9607
R3332
R1742
C1744
R w Y
L1701 C3346
8
L9602 R1735 R1738 C1739
C3322C3315C3311 R3329
C1738
R1717
39 C1732 IC501 C1740
C3328
64 FB3310 R1720
C1736
L1701
C3331 C1741 C1742
RED WHITE YELLOW
5
65
5
IC501 J502
C9615 R3333
1
WRITER 38
4
C1731
16
FB3302 C3340
R9628
C3307
SP
C9626
L1702 R9631 C3329 R3322
C513
C3303 R1519 C3325 R3321
R516
R1518
C3305 R3311 VA510
7–3
R3303
C3319 R3318 C514
C1731 IC3302
L1702
C3316 R3316 J503
C3317 VA511
1
C3312 R3314 R517
Q3301 C3321 R G
C3301
B
6
IC3301 C3308 R3313
P1701 R3306
R3310 HP
R1702
R1522 C1501
R7835 RED BLUE GREEN
R1521
R3309
4
R1510
SMT-A
IC3301 R1509
R1508 C508
P1701 J503
R1507 C507
R510
R1506
UL1 C1701 R505 C502 R504 C503VA504
L1703 R1505 R509
C501
R1504
VA505
C509
7
C1701 R522 102 R1503
C506
VA507
C505 R507 C510
1 C504
VA501
R506
C511
L1704 103
Q503
128 R512 J506
C3318 R3337R3336
R3304R3305 R1525R1526 R1529R1530 R1531R1532
R3315R3317 R511 w
L1703 C512
R
1
R521 R523 R1527R1528
TEST3 VA508 J506
L1704
Q502 R3320R3302R3301
P101 UP
A B C D E F G H
R3308 R1515
R519 R520
D1501
RED WHITE
8
C3310 R1541
USB VA513 VA512 R1537 R1536 Q1502 Q1501 R1514
5
Q1506 R1535
D1503 D1504 R1513
R1502
R1534
R1520 C3302TH3301 FDC3
Q1505 R1501
R1540 R1524 R1523
P101
R1512
R1516 D1502
R1533 R1517 Q1503
Q1504 19 1 FDC3
MAIN UNIT (CHIP SIDE-A)
R1511 HDMI
19 1
FDC1
S102 RIGHT S101
LEFT SC3803
LED
J3801
FDC1
J3801
9
POWER
SC3802 SC3803
SC3802
S101
HDMI
DOWN S102
10
LC-32LE260M
CAUTION:
This circuit diagram is original one, therefore there may be a slight
difference from yours.
SAFETY NOTES:
1) DISCONNECT THE AC PLUG FROM THE AC OUTLET
BEFORE REPLACING PARTS.
2) SEMICONDUCTOR HEAT SINKS SHOU LD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS
OPERATING.
8–1
F
B
C
D
H
A
G
1
R521
Q502 47K R3102 R3101
KTA1535T 10K 4.7K
E
Q503
B P3802
2SC3928AR
NB101WJ
C R523 R522
1K 10K SC3801
NB144WJQZ R3807
1
+5V
R519 0
5.1
1 PNL +12V
2
USB_DN
R3802 2 UR +13.5V
3
USB_DP 4 3 2 1 C9627
100K
WP
GND
GND
VCC
VCC
VCC
VCC
R520
GND
SDA
SCL
GND
ORX3-
10u
ORX3+
ORX2+
ORX2-
ORX1+
ORX1-
GND
ORX0+
ORX0-
GND
GND
J3801
ZA319WJQZ
OCLK+
OCLK-
GND
GND
GND
NC
GND
SELLVDS
5.1 R9601 R9619 GND WP SO/SIO1 CS C9601 3 UR +13.5v
4
LC-32LE260M
9
8
7
6
5
4
3
2
1
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
S101 3.3K TQ
KA037WJ IC3101 4 UR +13.5V
TWF TWF
D3101
TL3801
1/2W 1/2W
DB2S310L
W25Q32FV Q3801 GND
1
5
3
[2] MAIN UNIT
8 7 6 5 C3802 Q3802
KTA1535T 1u
2
SCLK KRC102S 6 GND
HOLD
NC
NC
EN
SI/SIO0 VCC
VCC
7 GND
10u
5 6 7 8
2
IC9604
C3801
BD00IC0E 8 GND
C9618
4.7u
0.1u
C3101
9 PS_ON
KZA931WJQZ
VOUT
FB
GND
NC
10 LAMP_ERR
VOL+ CH-UP
1 4 6 5 4 10K
1 2 3 4 R9630
11 PWM(OFL)
INPUT/MENU TL9610 FB9602 R3338
22P
2 5 A192WJ TU1101
22
C3347
D+1.26V 12 STB
NQA073WJQZ
R3340
100
CH-DOWN VOL P Q3302 13 Motion Flow
3 6 R9618 R9621 R9622 SDA SCL AIF- AIF+ NC NC IF_AGC NC 3.3V RESET NC
12K 1.5K 22K RN4983
1u
F F F 11 10 9 8 7 6 5 4 3 2 1
4.7u
C9619
R9628
S102
C9620
1 2 3
C9621
KZA931WJQZ
10K
KZA176WJ
KA050WJ R101
10u
R3309
8.2K
1K
C1113
R1105 0.1u C1115
100 C1108 10u
12K 8.2K C1106 C1107
R104 R103 0.01u
2.7K
0.1u 0.1u
R3310
C1112 OFL
4.7K
3
10u
R1103
R1106
4.7K
R1107
R1104
R1108 BLERR
100 33
33 FB1101
C1114
2 C1101
1000P
R1101 A191WJ
0.1u MF
33K
33K
3 180
R3301
R3302
C1104
1 180P
L1101
1u
J3301
0.1uH
JA039WJQZ
0.1u
0.1u
C3315
C3321
C3317
4.7K
4.7K
R3319
SERVICE
R3320
C1102 R1102
180 C1103 C1105
102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 0.1u
22P 22P
USB_DATA+
R1113
STB
100
VDDC
LED_G
SPI_DI
SPI_DO
SPI_CS
SPI_WP
RXO_0N
RXO_2P
RXO_3N
RXE_1P
RXE_2P
RXO_1N
RXO_1P
RXO_2N
RXO_3P
RXE_0N
RXE_0P
RXE_1N
RXE_2N.
RXO_CP
RXO_CN
RXO_0P
AC_CTRL
SPI_CLK
SP_MUTE
HP MUTE
103 AVDD_MOD RXE_CN 64
LAMP ERR
AVDD_MOD
AVDD_MOD
USB_DATA-
HP DETECT
PANEL_POW
104 GND RXE_CP 63
TUNER RESET
FB3305
POWER ON/OFF
HDMI1 Detect
HDMI2 Detect
0254TA
C3318
105 OFL RXE_3N 62 IC9605
0.1u
3416C25N
106 LED_R RXE_3P 61 FB3304
R3337 C3304 A192WJ
5
1
100 2.2u Vout Vin
107 UART_Rx RXE_4N 60
R3336 R1739
Q1704
2
100 GND
R1742 100K
4
UART_Tx
4.7K
108 RXE_4P 59 LTC044EEB
R3317
P101 C3322 10K
FB3308
TL1706
0254TA
4.7K
4
3
On
1K
NC
R3315
NB150WJ 0.1u
109 VDDIO_DATA VDDC 58 C9623
C3324 KZA510WJPZ
R3304
1K
RA T O LE D 0.1u 10u C9624
R3305
110 KEY1 AVDD_PLL 57 KZA520WJQZ
1u
D+3.3V KEY2 C3311
1 111 SDA 56 C1742
0.1u 1u R513
C1740 3 4
GND 112 THERM SCL 55 1u 33K
2
CD OUT
R/C
8
7
6
5
4 PST8429U
CN
CP
IC3301
VSS
R3308
LED_R 5 115 CPU RESET IXD632WJQZ VIFM 52 C1737
2.7K
9
VDD GND
4
0.1u
IC501 J503
10K
R105
117 HOTPLUG2 AVDD_REF 50 JA030WJQZ
TPA6139A R514
2
C3345 GND
11
GAIN 1K
5
10u
12
OUT_R OUT_L
4
0.01u
R1735 R1738
C3302
119 TMDS2 CLK+ 48
TH3301
XIN
R1517 2 1 1.5K 3.9K
GND
HXA057WJQZ
C3346
2
NC
NC
-IN_L
-IN_R
5
33 R516
R1717
3
C1732
16
14
15
13
SCA239WJQZ 100K
R3306 121 TMDS2 DATAO+ HP/LINEOUT_R 46 0.22u 0
R3329 24MHz
22K C3309 470 R1737
6
1
4
GND OUT C1741
R3307 1000P
1K R3331 C3340 R1701
125 HDMI_2 SCL PC_AUD_R 42 4.7K C1739
200K 1000P
C9617 1000P
2
3
VDD CD TMDS2 DATA2- C3313 KZA520WJQZ R9602
126 PC_AUD_L 41
1u 100
10u FB9601
127 TMDS2 DATA2+ 40 A192WJ
C3301 COMP_R
5
1
IC3302 0.01u
Vout Vin
PST8429U HOT
128 PLUG1 COMP_L 39
R9605
8–2
2
NC On 62K 0.1u
KZA510WJPZ R9612 F
PC_G
PC_VSYNC
CVBS2
CVBS_GND
AUREFM
PC_B
Video_GND
PC_R
AVDD_ADC25
COMP_Y
COMP_GND
COMP_Pr
CVBS3
AUVAG
AVDD_MOD
ARC
pc_SOG
COMP_Pb
COMP_SOG
AVDD_ADC33
CVBS1
CVBSOUT1
AVDD_AU33
CVBS_R
AVDD_12
TMDS1 DATA1-
HDMI_1 SDA
VSYNC
CVBS_L
TMDS1 DATA0+
TMDS1 DATA2+
PC_HSYNC
TMDS1 DATA0-
TMDS1 DATA1+
TMDS1 DATA2-
HDMI_1 SCL
TMDS1 CLK+
TMDS1 CLK-
10u 390 F R9610
R9617 5 6 7 8
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 5 6 7 8 100K
IC9603 100K
Q1506
D1503 3416C25N FB RT EN SS FB RT EN SS
DB2S310L D1504 LTC014EEB R9604
DB2S310L R9611 56K
SC3802 C3320 C3332 C3306
INPUT2 33K F
6
ZA321WJQZ 1u 2.2u 0.1u D+3.3V
C3307
TL3305
F
0.1u
IC9602 IC9601
0.1u C3303 FB3302 BD95835EFJ
R1536 47K C3310 0.1u FB3306 BD95835EFJ
20 21 A192WJ
2 4 6 8 10 12 14 16 18 0254TA
C9604
330P GND SW VIN BST
1 3 5 7 9 11 13 15 17 19 FB3307 GND SW VIN BST
C9611
22 23 A367WJQZ 390P 4 3 2 1 C9608
1000P
D+5.0V
0.047u
4 3 2 1
0.047u
FB3301 R9607 0.1u
R1533
0.047u
1K A192WJ 300K
10u
0.1u
C3328
R9614
C3331
F
82
330K C9607
C3308
R9609
Q1505
C3334
10u
C3305
82
C9614 C9615
C3319
C3312
C3316
F
0.047u
0.047u
R9616
0.047u
Q1504 LTC044EEB 0.1u
C3329
10u
10u
C9603
10u
C9602
33
33
LTC044EEB
68
C9622
10u
C9605
33
0.1u
10u
C9610
FB3310
10u
A192WJ
C9609
47K
47K
C9612
0.1u
33
33
68
L9601
R1534
R3313
R1535
PB014WJQZ
R3311
R3323
R3316
R3318
R3314
L9602
R1540 10uH
R3322
PB014WJQZ
100
10uH
FB3303
0254TA
R1541
100 C3337 R3330
200K
R1525 0 1000P
R3324 C3338
R1526 0 200K 1000P
7
R1527 0
R1528 0
R1529 0
R1530 0
100
100K
0.22u
100
R1521
R1531
C1734
R1715
0
1u
R1520
0.22u
C1733
1u
10 TW
R1719
C1719
C1716
100K
R1532 0
R1725
100K
R1721
R1716
1u
0.22u
C1710
C1735
100K
0
R1705
R7835
100
C1723
0.22u
Q1503
R7831 R1703
D1502 LTC014EEB 14 13 12 11 10 9 8 7 6 5 4 3 2 1
100 4.7K
D1501 DB2S310L BLERR
SC3803 DB2S310L
NC
SD
INPUT1 ZA321WJQZ MF
PBTL
AGND
GVDD
AVCC
LINN
LINP
RINP
RINN
GAIN1
GAIN0
FAULT
PLIMIT
20 21 IC1701
2 4 6 8 10 12 14 16 18 R1514 47K 29
TPA3020D
C7819
8
1 3 5 7 9 11 13 15 17 19
0.1u
22 23
PGND
OUTNR
PVCCR
PVCCR
BSPR
BSNL
OUTNL
OUTPL
PVCCL
BSNR
PGND
BSPL
PVCCL
OUTPR
2.2u
2.2u
KZA691WJ
C501
C504
C507
KZA691WJ
15 16 17 18 19 20 21 22 23 24 25 26 27 28
2.2u
2.2u
KZA691WJ
C510
Q1501
C1705
C1713
C1717
C1726
0.22u
0.22u
0.22u
0.22u
47K
47K
12K 12K
1u
0.1u
0.1u
C1729
100u
C1701
C1730
1000P
100u
C1731
C1704
C1702
C1703
1000P
R1513
R1512
C1706
330P
330P
330P
330P
C1714
C1718
10K
10K
C1727
R504
R506
R1708
L1702
L1704
10K
10
L1703
10K
TW 10
R511
R509
PB489WJQZ
PB489WJQZ
L1701
TW
10 TW
PB489WJQZ
R1714
TW 10
75
PB489WJQZ
R1726
R1503 0
R1723
*R7834
75
75
75
R502
R501
R503
R508
0
OFL
R1504 0
R1505 0
C1708
C1712
C1721
C1725
1000P
1000P
1000P
1000P
R1506 0
0
R1507
9
0
R1508
C1709
C1715
C1722
C1728
1u
1u
1u
1u
R1509 0
4 Lch +
R1510 0
3 Lch -
J502 12 6 9 3 11 5 8 2 10 4 7 1
ZA127WJ
2 Rch -
1 2 3 4
1 Rch +
J506
Pr Pb Y FA068WJQZ
10
PartsGuide
LC-32LE260M
PARTS GUIDE
No. S94M55LC-32LE260M
LED BACKLIGHT TV
MODEL: LC-32LE260M
CONTENTS
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
2
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
3
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
4
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
5
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
6
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
7
LC-32LE260M
[5] POWER Unit: DUNTKG409FM01
P7101 QPLGNB203WJZZ V PI Socket
C7007 RC-EZC030WJZZ V E-Cap
C7001 RC-FZA560WJN1 V Noise Suppression Capacitor
C7004 RC-FZA560WJN1 V Noise Suppression Capacitor
C7009 RC-FZA709WJQZ V Film capacitor
C7012 RC-KZB009WJN1 V Ceramic capacitor
L7001 RCILFA415WJQZ V Coil
D7101 RH-DX0229CEZZ V Diode
D7012 RH-FXA014WJZZ V Diode
VA7001 RH-VXA182WJN1 V Varistor
T7001 RTRNWA457WJPZ V Transformer
D7801 VHDSR560///-1 V Diode
8
LC-32LE260M
[6] CABINET AND MECHNICAL PARTS
1 CCABAD138WJ01 V Front Cabinet Assembly
1-1 GCABAD138WJ4A V Front cabinet
2 CCABBC376WJ01 V Rear Cabinet Assembly
2-1 GCABBC376WJ4A V Rear Cabinet
2-2 JBTN-B023WJ4A V Power Button
2-3 LANGKD438WJ4W V Vesa Angle (x2)
2-4 LANGKE164WJ4W V Vesa Angle (x2)
2-5 XEBS830P08000 V For vesa angle screw (x4)
3 CCOVAE996WJ01 V RC cover assembly
3-1 GCOVAE996WJ4A V RC cover
3-2 HDECQB904WJ4A V RC Decoration
4 GCOVAE341WJ4E V AC Cover
5 GCOVAE980WJ4A V Terminal Cover
6 JBTN-B024WJ4A V Joy Button
7 LANGKE313WJ4W V Bottom Bracket
8 LHLDWA101WJKZ V AC Cord Hook
9 QACCZA284WJPZ V AC Cord (Z/J/I/)
9 QACCZA285WJPZ2 V AC Cord (B)
9 QACCZA286WJPZ V AC Cord (P)
9 QACCBA139WJPZ V AC Cord (N)
10 QCNW-P255WJPZ V PD Wire
11 QCNW-P256WJPZ V LED/IR Wire
12 XBPS730P06WS0 V PWB & ANG screw (x11)
13 XBPS830P06WS0 V For Cab B (x12)
14 XEBS830P10000 V For Cab B (x5)
15 RSP-ZA704WJPZ V Speaker + Harness
[7] LCD PANEL
1 CLCDTA382WE01 V PANEL ASSY
2 CANGKE314WJ01 V KS TOP BEZEL
2-1 LANGKE314WJ4W V TOP BEZEL
2-2 PSPAGB390WJZZ V PORON H
3 CANGKE315WJ01 V KS BTM BEZEL
3-1 LANGKE315WJ4W V BTM BEZEL
3-2 PSPAGB390WJZZ V PORON H
4 CANGKE316WJ01 V KS LEFT BEZEL
4-1 LANGKE316WJ4W V LEFT BEZEL
4-2 PSPAGB391WJZZ V PORON V
5 CANGKE317WJ01 V KS RIGHT BEZEL
5-1 LANGKE317WJ4W V RIGHT BEZEL
5-2 PSPAGB391WJZZ V PORON V
6 CCHSMA731WJ01 V KS B.L CHASSIS
6-1 LCHSMA731WJ4W V B.L CHASSIS
7 LHLDWA360WJUZ V WH
8 LHLDWA361WJUZ V WH
9 LHLDZC216WJ4Z V Speaker holder
10 CHLDZC215WJ01 V KS P-FRAME
10-1 LHLDZC215WJ4A V P-FRAME
10-2 PSPAGB324WJZZ V PORON H
10-3 PSPAGB325WJZZ V PORON V
11 LHLDZC214WJ4A V SUPPORT PIN
12 LX-BZA556WJZZ V BEZEL SCREW
13 PCOVUA252WJZZ V DIFFUSION PLATE
14 PMIR-A369WJ4A V REFLECTION SHT
15 PSHEPB394WJZZ V DIFFUSION SHEET
16 PSHEPB395WJZZ V PRISM SHEET H
17 PSHEPB396WJZZ V PRISM SHEET V
18 PSPAHB380WJ4Z V HIMELON
19 QCNW-P257WJPZ V LVDS FFC
20 QCNW-P258WJPZ V LED BL WIRE
21 R1LK315T3HB60W V PANEL HIRAKI
22 RUNTKB283WJZZ V LED BAR (A)
23 RUNTKB284WJZZ V LED BAR (B)
9
LC-32LE260M
PRICE NEW PART
NO. PARTS CODE RANK MARK RANK DESCRIPTION
Supplied accessories
Remote control unit “AAA” size battery (g2)
X1
X2
X3
X4 X5 X6
Stand base Supporting post Screws (g 8)
10
LC-32LE260M
[9] PACKING PARTS ( NOT REPLACEMENT )
X4
S3
S6
X1 X2
X6
S2 X5
S5
X3
X7
S4
S8
S7
S1
11
LC-32LE260M
12
LC-32LE260M
[10] EXPLODE VIEW
13
LC-32LE260M
14
LC-32LE260M
15
LC-32LE260M
16
EndPage
COPYRIGHT © 2014
COPYRIGHT XXXXBY
BYSHARP
SHARP CORPORATION
CORPORATION
ALL RIGHTS RESERVED.
RQ244
SEPT2014 Printed in Malaysia SHARP MANUFACTURING
Design and Production Information CORPORATION (M) SDN. BHD
Design :SEM PQA DEPARTMENT
Production :SMM Batu Pahat, Johor,
SELVA SMM Malaysia
–1